RADLAN-OSPFV3-MIB

All MIBs › RADLAN-OSPFV3-MIB

Organization: Radlan Computer Communications Ltd.

Last Updated: 2011-05-04

Category: Routing, Vendor: RADLAN/Cisco SB

Description: Configures OSPFv3 routing for IPv6 networks on Radlan/Marvell switch platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RADLAN-OSPFV3-MIB?

RADLAN-OSPFV3-MIB is a vendor-specific private MIB from RADLAN/Marvell for configuring and monitoring multi-instance OSPFv3 (OSPF for IPv6) routing on switch/router platforms. Given its stated purpose as a multi-instance OSPFv3 MIB, it would expose configuration objects for OSPFv3 instances, areas, and interfaces, along with operational/protocol-state data analogous to the standard OSPFv3-MIB. Its monitoring relevance is protocol/software status: confirming that IPv6 OSPF instances and adjacencies are configured and operating as expected rather than exposing hardware environmentals. It is a vendor extension that parallels and depends conceptually on the standard IETF OSPFv3-MIB, adding multi-instance support. It is typically deployed on Marvell/RADLAN-based Layer 3 switches or routers that route IPv6 traffic using OSPFv3 in multi-instance configurations. Engineers can download the RADLAN-OSPFV3-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in RADLAN-OSPFV3-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Marvell (formerly RADLAN) Layer 3 switches/routers

Monitoring Examples

No object or table names were captured for this module in the source data, so specific polling targets cannot be cited; conceptually an administrator would inspect per-instance OSPFv3 configuration and neighbor/adjacency state to confirm IPv6 routing convergence across multiple OSPFv3 instances.

What Can Be Monitored

OSPFv3 instance configuration
OSPFv3 area configuration
OSPFv3 interface state

Imported Objects

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero

From INET-ADDRESS-MIB

InetAddress
InetAddressIPv6
InetAddressPrefixLength
InetAddressType

From OSPF-MIB

AreaID
BigMetric
DesignatedRouterPriority
HelloRange
Metric
OspfAuthenticationType
PositiveInteger
RouterID
Status
TOSType
UpToMaxAge

From OSPFV3-MIB

Ospfv3AreaIdTC
Ospfv3DeadIntervalRangeTC
Ospfv3IfInstIdTC
Ospfv3LsIdTC
Ospfv3LsaAgeTC
Ospfv3LsaSequenceTC
Ospfv3RouterIdTC
Ospfv3UpToRefreshIntervalTC

From RADLAN-MIB

rnd	OBJECT-IDENTITY

From RADLAN-OSPF-MIB

RlOspfFastHelloMultiplierRange
RlOspfProcessID
RlOspfRestartExitReason
RlOspfRestartHelperStatus
RlOspfRouterIdType

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32
mib-2

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using rlOspfv3OriginateNewLsas OID:

Select a Marvell (formerly RADLAN) Layer 3 switch/router (multi-instance OSPFv3) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type rlOspfv3OriginateNewLsas into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of new link state advertisements that have been originated. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
rlOspfv3	1.3.6.1.4.1.89.216			The private MIB module definition for Multi Instance OSPF V3 for IPv6 MIB.
RLO rlOspfv3Instance	1.3.6.1.4.1.89.216.1	RlOspfProcessID	read-write	Selected OSPFv3 Process ID. Additional key value for old fashion usage of OSPF standard MIB to support multi OSPF instance.
rlOspfv3GeneralGroupTable	1.3.6.1.4.1.89.216.2		not-accessible	OSPFv3 Instance General Variables
rlOspfv3GeneralGroupEntry	1.3.6.1.4.1.89.216.2.1		not-accessible	Information describing the configured global parame- ters to the Router OSPFv3 Process.
RLO rlOspfv3ProcessId	1.3.6.1.4.1.89.216.2.1.1	RlOspfProcessID	read-only	A 32-bit integer uniquely identifying an OSPFv3 process.
ROU rlOspfv3RouterId	1.3.6.1.4.1.89.216.2.1.2	RouterID	read-write	A 32-bit unsigned integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the 32-bit unsigned integer representation of one of the router's IPv4 interface addresses (if IPv4 is configured on the router). This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
STA rlOspfv3AdminStatus	1.3.6.1.4.1.89.216.2.1.3	Status	read-write	The administrative status of OSPFv3 in the router. The value 'enabled' denotes that the OSPFv3 Process is active on at least one interface; 'disabled' disables it on all interfaces. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
INT rlOspfv3VersionNumber	1.3.6.1.4.1.89.216.2.1.4	INTEGER	read-only	The version number of OSPF for IPv6 is 3.
T/F rlOspfv3AreaBdrRtrStatus	1.3.6.1.4.1.89.216.2.1.5	TruthValue	read-only	A flag to denote whether this router is an area border router. The value of this object is true (1) when the router is an area border router.
T/F rlOspfv3ASBdrRtrStatus	1.3.6.1.4.1.89.216.2.1.6	TruthValue	read-write	A flag to note whether this router is configured as an Autonomous System border router. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
G32 rlOspfv3AsScopeLsaCount	1.3.6.1.4.1.89.216.2.1.7	Gauge32	read-only	The number of AS-scope (e.g., AS-External) link state advertisements in the link state database.
U32 rlOspfv3AsScopeLsaCksumSum	1.3.6.1.4.1.89.216.2.1.8	Unsigned32	read-only	The 32-bit unsigned sum of the LS checksums of the AS-scoped link state advertisements contained in the link state database. This sum can be used to determine if there has been a change in a router's link state database or to compare the link state database of two routers.
C32 rlOspfv3OriginateNewLsasEx	1.3.6.1.4.1.89.216.2.1.9	Counter32	read-only	The number of new link state advertisements that have been originated. This number is incremented each time the router originates a new LSA. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of ospfv3DiscontinuityTime.
C32 rlOspfv3RxNewLsas	1.3.6.1.4.1.89.216.2.1.10	Counter32	read-only	The number of link state advertisements received that are determined to be new instantiations. This number does not include newer instantiations of self-originated link state advertisements. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of ospfv3DiscontinuityTime.
G32 rlOspfv3ExtLsaCount	1.3.6.1.4.1.89.216.2.1.11	Gauge32	read-only	The number of External (LS type 0x4005) in the link state database.
I32 rlOspfv3ExtAreaLsdbLimit	1.3.6.1.4.1.89.216.2.1.12	Integer32	read-write	The maximum number of non-default AS-external-LSA entries that can be stored in the link state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link state database reaches ospfv3ExtAreaLsdbLimit, the router enters Overflow state. The router never holds more than ospfv3ExtAreaLsdbLimit non-default AS-external-LSAs in its database. ospfv3ExtAreaLsdbLimit MUST be set identically in all routers attached to the OSPFv3 backbone and/or any regular OSPFv3 area (i.e., OSPFv3 stub areas and not-so-stubby-areas (NSSAs) are excluded). This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
U32 rlOspfv3ExitOverflowInterval	1.3.6.1.4.1.89.216.2.1.13	Unsigned32	read-write	The number of seconds that, after entering Overflow state, a router will attempt to leave Overflow state. This allows the router to again originate non-default, AS-External-LSAs. When set to 0, the router will not leave Overflow state until restarted. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
T/F rlOspfv3DemandExtensions	1.3.6.1.4.1.89.216.2.1.14	TruthValue	read-write	The router's support for demand circuits. The value of this object is true (1) when demand circuits are supported. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
U32 rlOspfv3ReferenceBandwidth	1.3.6.1.4.1.89.216.2.1.15	Unsigned32	read-write	Reference bandwidth in kilobits per second for calculating default interface metrics. The default value is 100,000 KBPS (100 MBPS). This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
INT rlOspfv3RestartSupport	1.3.6.1.4.1.89.216.2.1.16	INTEGER	read-write	The router's support for OSPF graceful restart. Options include no restart support, only planned restarts, or both planned and unplanned restarts. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
NUM rlOspfv3RestartInterval	1.3.6.1.4.1.89.216.2.1.17	Ospfv3UpToRefreshIntervalTC	read-write	Configured OSPF graceful restart timeout interval. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
T/F rlOspfv3RestartStrictLsaChecking	1.3.6.1.4.1.89.216.2.1.18	TruthValue	read-write	Indicates if strict LSA checking is enabled for graceful restart. A value of true (1) indicates that strict LSA checking is enabled. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
INT rlOspfv3RestartStatus	1.3.6.1.4.1.89.216.2.1.19	INTEGER	read-only	The current status of OSPF graceful restart capability.
NUM rlOspfv3RestartAge	1.3.6.1.4.1.89.216.2.1.20	Ospfv3UpToRefreshIntervalTC	read-only	Remaining time in the current OSPF graceful restart interval.
INT rlOspfv3RestartExitReason	1.3.6.1.4.1.89.216.2.1.21	INTEGER	read-only	Describes the outcome of the last attempt at a graceful restart. none: no restart has yet been attempted. inProgress: a restart attempt is currently underway. completed: the last restart completed successfully. timedOut: the last restart timed out. topologyChanged: the last restart was aborted due to a topology change.
T/F rlOspfv3NotificationEnable	1.3.6.1.4.1.89.216.2.1.22	TruthValue	read-write	This object provides a coarse level of control over the generation of OSPFv3 notifications. If this object is set to true (1), then it enables the generation of OSPFv3 notifications. If it is set to false (2), these notifications are not generated. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
T/F rlOspfv3StubRouterSupport	1.3.6.1.4.1.89.216.2.1.23	TruthValue	read-only	The router's support for stub router functionality. An object value of true (1) indicates that stub router functionality is supported.
INT rlOspfv3StubRouterAdvertisement	1.3.6.1.4.1.89.216.2.1.24	INTEGER	read-write	This object controls the advertisement of stub LSAs by the router. The value doNotAdvertise (1) will result in the advertisement of standard LSAs and is the default value. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
TIM rlOspfv3DiscontinuityTime	1.3.6.1.4.1.89.216.2.1.25	TimeStamp	read-only	The value of sysUpTime on the most recent occasion at which any one of this MIB's counters suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value.
TIM rlOspfv3RestartTime	1.3.6.1.4.1.89.216.2.1.26	TimeStamp	read-only	The value of sysUpTime on the most recent occasion at which the ospfv3RestartExitReason was updated.
INT rlOspfv3OperStatus	1.3.6.1.4.1.89.216.2.1.27	INTEGER	read-only	The current operational state of the OSPF in the router.
ROW rlOspfv3RowStatus	1.3.6.1.4.1.89.216.2.1.28	RowStatus	read-create	This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
INT rlOspfv3LogAdjacencyChanges	1.3.6.1.4.1.89.216.2.1.29	INTEGER	read-write	Configure the router to send a syslog message when an OSPF neighbor goes up or down. detail � sends a syslog message for each state change, not just when a neighbor goes up or down
T/F rlOspfv3PassiveInterface	1.3.6.1.4.1.89.216.2.1.30	TruthValue	read-write	A flag to note whether to disable sending OSPF routing updates on all OSPF IP interfaces.
I32 rlOspfv3DefaultMetric	1.3.6.1.4.1.89.216.2.1.31	Integer32	read-write	A default metric helps solve the problem of redistributing routes with incompatible metrics. Whenever metrics do not convert, using a default metric provides a reasonable substitute and enables the redistribution to proceed.
I32 rlOspfv3MaximumRedistPrefixNum	1.3.6.1.4.1.89.216.2.1.32	Integer32	read-write	Specifies the maximum number of IP prefixes that can be redistributed into OSPF.
I32 rlOspfv3MaximumRedistPrefixThreshold	1.3.6.1.4.1.89.216.2.1.33	Integer32	read-write	Threshold value, as a percentage, at which a warning message should be generated.
T/F rlOspfv3MaximumRedistPrefixWarningOnly	1.3.6.1.4.1.89.216.2.1.34	TruthValue	read-write	Causes a warning message to be logged when the number of prefixes defined by the maximum argumenthas been exceeded. Additional redistribution is not prevented.
ROU rlOspfv3NextRouterId	1.3.6.1.4.1.89.216.2.1.35	RouterID	read-only	A 32-bit integer uniquely identifying the of router in the Autonomous System after restart. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
RLO rlOspfv3RouterIdType	1.3.6.1.4.1.89.216.2.1.36	RlOspfRouterIdType	read-only	Type of router identifier - default value or manually set by user.
RLO rlOspfv3NextRouterIdType	1.3.6.1.4.1.89.216.2.1.37	RlOspfRouterIdType	read-only	Type of router identifier after restart - default value or manually set by user.
T/F rlOspfv3ASBdrRtrActualStatus	1.3.6.1.4.1.89.216.2.1.38	TruthValue	read-only	A flag to note whether this router is an Autonomous System Border Router. note: rlOspfASBdrRtrStatus field is the configuration and this filed is the actual ASBR status
U32 rlOspfv3CalcMaxDelay	1.3.6.1.4.1.89.216.2.1.39	Unsigned32	read-write	The maximum delay before the Routing Table is recalculated following a change to the Link State Database. (Recalculation is delayed to reduce the frequency of recalculations of the Routing Table). This parameter has units of milliseconds. A value of 0 indicates that a routing calculation will immediately follow an update to the database.
U32 rlOspfv3RteMaxEqCostPaths	1.3.6.1.4.1.89.216.2.1.40	Unsigned32	read-write	The maximum number of equal cost paths that are stored for each destination in the Routing Table.
rlOspfv3AreaTable	1.3.6.1.4.1.89.216.3		not-accessible	Information describing the configured parameters and cumulative statistics of the router's attached areas. The interfaces and virtual links are configured as part of these areas. Area 0, by definition, is the backbone area.
rlOspfv3AreaEntry	1.3.6.1.4.1.89.216.3.1		not-accessible	Information describing the configured parameters and cumulative statistics of one of the router's attached areas. The information in this table is persistent, and when written, the entity SHOULD save the a change to non-volatile storage.
RLO rlOspfv3AreaProcessId	1.3.6.1.4.1.89.216.3.1.1	RlOspfProcessID	read-only	A 32-bit integer uniquely identifying an OSPF process.
ARE rlOspfv3AreaId	1.3.6.1.4.1.89.216.3.1.2	AreaID	not-accessible	A 32-bit unsigned integer uniquely identifying an area. Area ID 0 is used for the OSPFv3 backbone.
INT rlOspfv3AreaImportAsExtern	1.3.6.1.4.1.89.216.3.1.3	INTEGER	read-create	Indicates whether an area is a stub area, NSSA, or standard area. AS-scope LSAs are not imported into stub areas or NSSAs. NSSAs import AS-External data as NSSA LSAs that have Area-scope.
C32 rlOspfv3AreaSpfRuns	1.3.6.1.4.1.89.216.3.1.4	Counter32	read-only	The number of times that the intra-area route table has been calculated using this area's link state database. This is typically done using Dijkstra's algorithm. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of rlOspfv3DiscontinuityTime.
G32 rlOspfv3AreaBdrRtrCount	1.3.6.1.4.1.89.216.3.1.5	Gauge32	read-only	The total number of area border routers reachable within this area. This is initially zero, and is calculated in each Shortest Path First (SPF) pass.
G32 rlOspfv3AreaAsBdrRtrCount	1.3.6.1.4.1.89.216.3.1.6	Gauge32	read-only	The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF pass.
G32 rlOspfv3AreaScopeLsaCount	1.3.6.1.4.1.89.216.3.1.7	Gauge32	read-only	The total number of Area-scope link state advertisements in this area's link state database.
U32 rlOspfv3AreaScopeLsaCksumSum	1.3.6.1.4.1.89.216.3.1.8	Unsigned32	read-only	The 32-bit unsigned sum of the Area-scope link state advertisements' LS checksums contained in this area's link state database. The sum can be used to determine if there has been a change in a router's link state database or to compare the link state database of two routers.
INT rlOspfv3AreaSummary	1.3.6.1.4.1.89.216.3.1.9	INTEGER	read-create	The variable rlOspfv3AreaSummary controls the import of Inter-Area LSAs into stub and NSSA areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate Inter-Area LSAs into the stub or NSSA area. It will only advertise a default route. If it is sendAreaSummary, the router will both summarize and propagate Inter-Area LSAs.
ROW rlOspfv3AreaRowStatus	1.3.6.1.4.1.89.216.3.1.10	RowStatus	read-create	This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
BIG rlOspfv3AreaStubMetric	1.3.6.1.4.1.89.216.3.1.11	BigMetric	read-create	The metric value advertised for the default route into stub and NSSA areas. By default, this equals the least metric among the interfaces to other areas.
INT rlOspfv3AreaNssaTranslatorRole	1.3.6.1.4.1.89.216.3.1.12	INTEGER	read-create	Indicates an NSSA border router's policy to perform NSSA translation of NSSA-LSAs into AS-External-LSAs.
INT rlOspfv3AreaNssaTranslatorState	1.3.6.1.4.1.89.216.3.1.13	INTEGER	read-only	Indicates if and how an NSSA border router is performing NSSA translation of NSSA-LSAs into AS-External-LSAs. When this object is set to 'enabled', the NSSA border router's rlOspfv3AreaNssaTranslatorRole has been set to 'always'. When this object is set to 'elected', a candidate NSSA border router is translating NSSA-LSAs into AS-External-LSAs. When this object is set to 'disabled', a candidate NSSA Border router is NOT translating NSSA-LSAs into AS-External-LSAs.
U32 rlOspfv3AreaNssaTranslatorStabInterval	1.3.6.1.4.1.89.216.3.1.14	Unsigned32	read-create	The stability interval defined as the number of seconds after an elected translator determines its services are no longer required that it should continue to perform its translation duties.
C32 rlOspfv3AreaNssaTranslatorEvents	1.3.6.1.4.1.89.216.3.1.15	Counter32	read-only	Indicates the number of Translator state changes that have occurred since the last start-up of the OSPFv3 routing process. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of rlOspfv3DiscontinuityTime.
INT rlOspfv3AreaStubMetricType	1.3.6.1.4.1.89.216.3.1.16	INTEGER	read-create	This variable assigns the type of metric advertised as a default route.
T/F rlOspfv3AreaTEEnabled	1.3.6.1.4.1.89.216.3.1.17	TruthValue	read-create	Indicates whether or not traffic engineering is enabled in the area. The object is set to the value true (1) to enable traffic engineering. Traffic engineering is disabled by default.
STA rlOspfv3AreaAdminStat	1.3.6.1.4.1.89.216.3.1.18	Status	read-create	The OSPF Area's administrative status. The value formed on the area, and the in- terfaces associated with the area. The value 'disabled' denotes that the area is external to OSPF.
INT rlOspfv3AreaOperStatus	1.3.6.1.4.1.89.216.3.1.19	INTEGER	read-only	The current operational state of the OSPF Area.
STR rlOspfv3AreaFilterPrefixListIn	1.3.6.1.4.1.89.216.3.1.20	DisplayString	read-write	The prefix list is applied to prefixes advertised to the specified area from other areas.
STR rlOspfv3AreaFilterPrefixListOut	1.3.6.1.4.1.89.216.3.1.21	DisplayString	read-write	The prefix list is applied to prefixes advertised out of the specified area to other areas.
rlOspfv3AsLsdbTable	1.3.6.1.4.1.89.216.4		not-accessible	The OSPFv3 Process's AS-scope link state database (LSDB). The LSDB contains the AS-scope link state advertisements from throughout the areas that the device is attached to.
rlOspfv3AsLsdbEntry	1.3.6.1.4.1.89.216.4.1		not-accessible	A single AS-scope link state advertisement.
RLO rlOspfv3AsLsdbProcessId	1.3.6.1.4.1.89.216.4.1.1	RlOspfProcessID	read-only	A 32-bit integer uniquely identifying an OSPF process.
U32 rlOspfv3AsLsdbType	1.3.6.1.4.1.89.216.4.1.2	Unsigned32	not-accessible	The type of the link state advertisement. Each link state type has a separate advertisement format. AS-scope LSAs not recognized by the router may be stored in the database.
ROU rlOspfv3AsLsdbRouterId	1.3.6.1.4.1.89.216.4.1.3	RouterID	not-accessible	The 32-bit number that uniquely identifies the originating router in the Autonomous System.
RLL rlOspfv3AsLsdbLsid	1.3.6.1.4.1.89.216.4.1.4	RlLsID	not-accessible	The Link State ID is an LS type-specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
OSP rlOspfv3AsLsdbSequence	1.3.6.1.4.1.89.216.4.1.5	Ospfv3LsaSequenceTC	read-only	The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number, the more recent the advertisement.
OSP rlOspfv3AsLsdbAge	1.3.6.1.4.1.89.216.4.1.6	Ospfv3LsaAgeTC	read-only	This field is the age of the link state advertisement in seconds. The high-order bit of the LS age field is considered the DoNotAge bit for support of on-demand circuits.
I32 rlOspfv3AsLsdbChecksum	1.3.6.1.4.1.89.216.4.1.7	Integer32	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OCT rlOspfv3AsLsdbAdvertisement	1.3.6.1.4.1.89.216.4.1.8	OCTET STRING	read-only	The entire link state advertisement, including its header.
T/F rlOspfv3AsLsdbTypeKnown	1.3.6.1.4.1.89.216.4.1.9	TruthValue	read-only	The value true (1) indicates that the LSA type is recognized by this router.
rlOspfv3AreaLsdbTable	1.3.6.1.4.1.89.216.5		not-accessible	The OSPFv3 Process's Area-scope LSDB. The LSDB contains the Area-scope link state advertisements from throughout the area that the device is attached to.
rlOspfv3AreaLsdbEntry	1.3.6.1.4.1.89.216.5.1		not-accessible	A single Area-scope link state advertisement.
RLO rlOspfv3AreaLsdbProcessId	1.3.6.1.4.1.89.216.5.1.1	RlOspfProcessID	read-only	A 32-bit integer uniquely identifying an OSPF process.
ARE rlOspfv3AreaLsdbAreaId	1.3.6.1.4.1.89.216.5.1.2	AreaID	not-accessible	The 32-bit identifier of the Area from which the LSA was received.
U32 rlOspfv3AreaLsdbType	1.3.6.1.4.1.89.216.5.1.3	Unsigned32	not-accessible	The type of the link state advertisement. Each link state type has a separate advertisement format. Area-scope LSAs unrecognized by the router are also stored in this database.
ROU rlOspfv3AreaLsdbRouterId	1.3.6.1.4.1.89.216.5.1.4	RouterID	not-accessible	The 32-bit number that uniquely identifies the originating router in the Autonomous System.
RLL rlOspfv3AreaLsdbLsid	1.3.6.1.4.1.89.216.5.1.5	RlLsID	not-accessible	The Link State ID is an LS type-specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
OSP rlOspfv3AreaLsdbSequence	1.3.6.1.4.1.89.216.5.1.6	Ospfv3LsaSequenceTC	read-only	The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number, the more recent the advertisement.
OSP rlOspfv3AreaLsdbAge	1.3.6.1.4.1.89.216.5.1.7	Ospfv3LsaAgeTC	read-only	This field is the age of the link state advertisement in seconds. The high-order bit of the LS age field is considered the DoNotAge bit for support of on-demand circuits.
I32 rlOspfv3AreaLsdbChecksum	1.3.6.1.4.1.89.216.5.1.8	Integer32	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OCT rlOspfv3AreaLsdbAdvertisement	1.3.6.1.4.1.89.216.5.1.9	OCTET STRING	read-only	The entire link state advertisement, including its header.
T/F rlOspfv3AreaLsdbTypeKnown	1.3.6.1.4.1.89.216.5.1.10	TruthValue	read-only	The value true (1) indicates that the LSA type is recognized by this router.
rlOspfv3LinkLsdbTable	1.3.6.1.4.1.89.216.6		not-accessible	The OSPFv3 Process's Link-scope LSDB for non-virtual interfaces. The LSDB contains the Link-scope link state advertisements from the interfaces that the device is attached to.
rlOspfv3LinkLsdbEntry	1.3.6.1.4.1.89.216.6.1		not-accessible	A single Link-scope link state advertisement.
RLO rlOspfv3LinkLsdbProcessId	1.3.6.1.4.1.89.216.6.1.1	RlOspfProcessID	read-only	A 32-bit integer uniquely identifying an OSPF process.
NUM rlOspfv3LinkLsdbIfIndex	1.3.6.1.4.1.89.216.6.1.2	InterfaceIndex	not-accessible	The identifier of the link from which the LSA was received.
OSP rlOspfv3LinkLsdbIfInstId	1.3.6.1.4.1.89.216.6.1.3	Ospfv3IfInstIdTC	not-accessible	The identifier of the interface instance from which the LSA was received.
U32 rlOspfv3LinkLsdbType	1.3.6.1.4.1.89.216.6.1.4	Unsigned32	not-accessible	The type of the link state advertisement. Each link state type has a separate advertisement format. Link-scope LSAs unrecognized by the router are also stored in this database.
ROU rlOspfv3LinkLsdbRouterId	1.3.6.1.4.1.89.216.6.1.5	RouterID	not-accessible	The 32-bit number that uniquely identifies the originating router in the Autonomous System.
RLL rlOspfv3LinkLsdbLsid	1.3.6.1.4.1.89.216.6.1.6	RlLsID	not-accessible	The Link State ID is an LS type-specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics. However, in OSPFv3 the Link State ID always contains the flooding scope of the LSA.
OSP rlOspfv3LinkLsdbSequence	1.3.6.1.4.1.89.216.6.1.7	Ospfv3LsaSequenceTC	read-only	The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number, the more recent the advertisement.
OSP rlOspfv3LinkLsdbAge	1.3.6.1.4.1.89.216.6.1.8	Ospfv3LsaAgeTC	read-only	This field is the age of the link state advertisement in seconds. The high-order bit of the LS age field is considered the DoNotAge bit for support of on-demand circuits.
I32 rlOspfv3LinkLsdbChecksum	1.3.6.1.4.1.89.216.6.1.9	Integer32	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OCT rlOspfv3LinkLsdbAdvertisement	1.3.6.1.4.1.89.216.6.1.10	OCTET STRING	read-only	The entire link state advertisement, including its header.
T/F rlOspfv3LinkLsdbTypeKnown	1.3.6.1.4.1.89.216.6.1.11	TruthValue	read-only	The value true (1) indicates that the LSA type is recognized by this router.
rlOspfv3HostTable	1.3.6.1.4.1.89.216.7		not-accessible	The Host/Metric Table indicates what hosts are directly attached to the router and their corresponding metrics.
rlOspfv3HostEntry	1.3.6.1.4.1.89.216.7.1		not-accessible	A metric to be advertised when a given host is reachable. The information in this table is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
RLO rlOspfv3HostProcessId	1.3.6.1.4.1.89.216.7.1.1	RlOspfProcessID	read-only	A 32-bit integer uniquely identifying an OSPF process.
IPt rlOspfv3HostAddressType	1.3.6.1.4.1.89.216.7.1.2	InetAddressType	not-accessible	The address type of rlOspfv3HostAddress. Only IPv6 global address type is expected.
IP rlOspfv3HostAddress	1.3.6.1.4.1.89.216.7.1.3	InetAddress	not-accessible	The IPv6 address of the host. Must be an IPv6 global address.
MET rlOspfv3HostMetric	1.3.6.1.4.1.89.216.7.1.4	Metric	read-create	The metric to be advertised.
ROW rlOspfv3HostRowStatus	1.3.6.1.4.1.89.216.7.1.5	RowStatus	read-create	This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
ARE rlOspfv3HostAreaID	1.3.6.1.4.1.89.216.7.1.6	AreaID	read-create	The Area the host entry is to be found within. By default, the area for the subsuming OSPFv3 interface, or Area 0 if there is no subsuming interface.
rlOspfv3IfTable	1.3.6.1.4.1.89.216.8		not-accessible	The OSPFv3 Interface Table describes the interfaces from the viewpoint of OSPFv3.
rlOspfv3IfEntry	1.3.6.1.4.1.89.216.8.1		not-accessible	The OSPFv3 Interface Entry describes one interface from the viewpoint of OSPFv3. The information in this table is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
RLO rlOspfv3IfProcessId	1.3.6.1.4.1.89.216.8.1.1	RlOspfProcessID	read-only	A 32-bit integer uniquely identifying an OSPF process.
NUM rlOspfv3IfIndex	1.3.6.1.4.1.89.216.8.1.2	InterfaceIndex	not-accessible	The interface index of this OSPFv3 interface. It corresponds to the interface index of the IPv6 interface on which OSPFv3 is configured.
OSP rlOspfv3IfInstId	1.3.6.1.4.1.89.216.8.1.3	Ospfv3IfInstIdTC	not-accessible	Enables multiple interface instances of OSPFv3 to be run over a single link. Each interface instance would be assigned a separate ID. This ID has local link significance only.
ARE rlOspfv3IfAreaId	1.3.6.1.4.1.89.216.8.1.4	AreaID	read-create	A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0 is used for the OSPFv3 backbone.
INT rlOspfv3IfType	1.3.6.1.4.1.89.216.8.1.5	INTEGER	read-create	The OSPFv3 interface type.
STA rlOspfv3IfAdminStatus	1.3.6.1.4.1.89.216.8.1.6	Status	read-create	The OSPFv3 interface's administrative status. The value formed on the interface; the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPFv3. Note that a value of 'disabled' for the object rlOspfv3AdminStatus will override a value of 'enabled' for the interface.
DES rlOspfv3IfRtrPriority	1.3.6.1.4.1.89.216.8.1.7	DesignatedRouterPriority	read-create	The priority of this interface. Used in multi-access networks, this field is used in the designated-router election algorithm. The value 0 signifies that the router is not eligible to become the Designated Router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker.
NUM rlOspfv3IfTransitDelay	1.3.6.1.4.1.89.216.8.1.8	RlOspfv3UpToRefreshIntervalTC	read-create	The estimated number of seconds it takes to transmit a Link State Update packet over this interface. LSAs contained in the update packet must have their age incremented by this amount before transmission. This value should take into account the transmission and propagation delays of the interface.
NUM rlOspfv3IfRetransInterval	1.3.6.1.4.1.89.216.8.1.9	RlOspfv3UpToRefreshIntervalTC	read-create	The number of seconds between link state advertisement retransmissions for adjacencies belonging to this interface. This value is also used when retransmitting database description and Link State Request packets.
HEL rlOspfv3IfHelloInterval	1.3.6.1.4.1.89.216.8.1.10	HelloRange	read-create	The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
NUM rlOspfv3IfRtrDeadInterval	1.3.6.1.4.1.89.216.8.1.11	Ospfv3DeadIntervalRangeTC	read-create	The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down on the interface. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
U32 rlOspfv3IfPollInterval	1.3.6.1.4.1.89.216.8.1.12	Unsigned32	read-create	The larger time interval, in seconds, between the Hello packets sent to an inactive, non-broadcast multi-access neighbor.
INT rlOspfv3IfState	1.3.6.1.4.1.89.216.8.1.13	INTEGER	read-only	The OSPFv3 interface state. An interface may be in standby state if there are multiple interfaces on the link and another interface is active. The interface may be in Down state if the underlying IPv6 interface is down or if the admin status is 'disabled' either globally or for the interface.
ROU rlOspfv3IfDesignatedRouter	1.3.6.1.4.1.89.216.8.1.14	RouterID	read-only	The Router ID of the Designated Router.
ROU rlOspfv3IfBackupDesignatedRouter	1.3.6.1.4.1.89.216.8.1.15	RouterID	read-only	The Router ID of the Backup Designated Router.
C32 rlOspfv3IfEvents	1.3.6.1.4.1.89.216.8.1.16	Counter32	read-only	The number of times this OSPFv3 interface has changed its state or an error has occurred. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of rlOspfv3DiscontinuityTime.
ROW rlOspfv3IfRowStatus	1.3.6.1.4.1.89.216.8.1.17	RowStatus	read-create	This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
T/F rlOspfv3IfDemand	1.3.6.1.4.1.89.216.8.1.18	TruthValue	read-create	Indicates whether Demand OSPFv3 procedures (Hello suppression to FULL neighbors and setting the DoNotAge flag on propagated LSAs) should be performed on this interface.
MET rlOspfv3IfMetricValue	1.3.6.1.4.1.89.216.8.1.19	Metric	read-create	The metric assigned to this interface. The default value of the metric is 'Reference Bandwidth / ifSpeed'. The value of the reference bandwidth can be set in the rlOspfv3ReferenceBandwidth object.
G32 rlOspfv3IfLinkScopeLsaCount	1.3.6.1.4.1.89.216.8.1.20	Gauge32	read-only	The total number of Link-scope link state advertisements in this link's link state database.
U32 rlOspfv3IfLinkLsaCksumSum	1.3.6.1.4.1.89.216.8.1.21	Unsigned32	read-only	The 32-bit unsigned sum of the Link-scope link state advertisements' LS checksums contained in this link's link state database. The sum can be used to determine if there has been a change in a router's link state database or to compare the link state database of two routers.
T/F rlOspfv3IfDemandNbrProbe	1.3.6.1.4.1.89.216.8.1.22	TruthValue	read-create	Indicates whether or not neighbor probing is enabled to determine whether or not the neighbor is inactive. Neighbor probing is disabled by default.
U32 rlOspfv3IfDemandNbrProbeRetransLimit	1.3.6.1.4.1.89.216.8.1.23	Unsigned32	read-create	The number of consecutive LSA retransmissions before the neighbor is deemed inactive and the neighbor adjacency is brought down.
U32 rlOspfv3IfDemandNbrProbeInterval	1.3.6.1.4.1.89.216.8.1.24	Unsigned32	read-create	Defines how often the neighbor will be probed.
T/F rlOspfv3IfTEDisabled	1.3.6.1.4.1.89.216.8.1.25	TruthValue	read-create	Indicates whether or not traffic engineering is disabled on the interface when traffic engineering is enabled in the area where the interface is attached. The object is set to the value true (1) to disable traffic engineering on the interface. Traffic engineering is enabled by default on the interface when traffic engineering is enabled in the area where the interface is attached.
T/F rlOspfv3IfLinkLSASuppression	1.3.6.1.4.1.89.216.8.1.26	TruthValue	read-create	Specifies whether or not link LSA origination is suppressed for broadcast or NBMA interface types. The object is set to value true (1) to suppress the origination.
INT rlOspfv3IfOperStatus	1.3.6.1.4.1.89.216.8.1.27	INTEGER	read-only	The current operational state of the OSPF interface.
T/F rlOspfv3IfPassive	1.3.6.1.4.1.89.216.8.1.28	TruthValue	read-write	Indicates whether this interface is a passive interface. If set to TRUE, we suppress HELLO packets sent on and received from this interface. We will therefore advertise this interface in our LSAs but not run OSPF protocol over it.
I32 rlOspfv3IfLsaRefreshIntvl	1.3.6.1.4.1.89.216.8.1.29	Integer32	read-write	Self-originated LSAs are periodically reflooded into the routing domain, to add to the robustness of the OSPF protocol. This value determines the interval between refreshes of LSAs that are only flooded over this interface, for example type-9 opaque LSAs, and is defaulted to the OSPF standard default of 1800 seconds (30 minutes).
RLO rlOspfv3IfFastHelloMultiplier	1.3.6.1.4.1.89.216.8.1.30	RlOspfv3FastHelloMultiplierRange	read-create	The number of Hellos that should be sent within 1 second when using Fast Hellos on this interface. This value does not have to be same for all routers attached to a common network, but it is advisable. Fast Hellos are configured using ospfPmIfRtrDeadInterval.
T/F rlOspfv3IfMtuIgnore	1.3.6.1.4.1.89.216.8.1.31	TruthValue	read-write	This object controls whether DC-OSPF checks the MTU size on incoming Database Description packets. By default, if the received MTU size in a DB Description packet is higher than the MTU size configured on the incoming interface, the OSPF adjacency will not be established. If the interface is tunneled over, say, an MPLS network, then the administrator may not know the maximum MTU size and so can tell DC-OSPF to ignore the MTU size on incoming DB description packets.
T/F rlOspfv3IfNameLookup	1.3.6.1.4.1.89.216.8.1.32	TruthValue	read-write	A flag to note whether to look up Domain Name System (DNS) names for use in all OSPF show EXEC command displays.
rlOspfv3VirtIfTable	1.3.6.1.4.1.89.216.9		not-accessible	Information about this router's virtual interfaces that the OSPFv3 Process is configured to carry on.
rlOspfv3VirtIfEntry	1.3.6.1.4.1.89.216.9.1		not-accessible	Information about a single virtual interface. The information in this table is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
RLO rlOspfv3VirtIfProcessId	1.3.6.1.4.1.89.216.9.1.1	RlOspfProcessID	read-only	A 32-bit integer uniquely identifying an OSPF process.
ARE rlOspfv3VirtIfAreaId	1.3.6.1.4.1.89.216.9.1.2	AreaID	not-accessible	The transit area that the virtual link traverses. By definition, this is not Area 0.
ROU rlOspfv3VirtIfNeighbor	1.3.6.1.4.1.89.216.9.1.3	RouterID	not-accessible	The Router ID of the virtual neighbor.
NUM rlOspfv3VirtIfIndex	1.3.6.1.4.1.89.216.9.1.4	InterfaceIndex	read-only	The local interface index assigned by the OSPFv3 Process to this OSPFv3 virtual interface. It is advertised in Hellos sent over the virtual link and in the router's router-LSAs.
OSP rlOspfv3VirtIfInstId	1.3.6.1.4.1.89.216.9.1.5	Ospfv3IfInstIdTC	read-only	The local Interface Instance ID assigned by the OSPFv3 Process to this OSPFv3 virtual interface.
NUM rlOspfv3VirtIfTransitDelay	1.3.6.1.4.1.89.216.9.1.6	RlOspfv3UpToRefreshIntervalTC	read-create	The estimated number of seconds it takes to transmit a Link State Update packet over this interface.
NUM rlOspfv3VirtIfRetransInterval	1.3.6.1.4.1.89.216.9.1.7	RlOspfv3UpToRefreshIntervalTC	read-create	The number of seconds between link state advertisement retransmissions for adjacencies belonging to this interface. This value is also used when retransmitting database description and Link State Request packets. This value should be well over the expected round-trip time.
HEL rlOspfv3VirtIfHelloInterval	1.3.6.1.4.1.89.216.9.1.8	HelloRange	read-create	The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor.
NUM rlOspfv3VirtIfRtrDeadInterval	1.3.6.1.4.1.89.216.9.1.9	Ospfv3DeadIntervalRangeTC	read-create	The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor.
INT rlOspfv3VirtIfState	1.3.6.1.4.1.89.216.9.1.10	INTEGER	read-only	OSPF virtual interface states. The same encoding as the ospfV3IfTable is used.
C32 rlOspfv3VirtIfEvents	1.3.6.1.4.1.89.216.9.1.11	Counter32	read-only	The number of state changes or error events on this virtual link. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of rlOspfv3DiscontinuityTime.
ROW rlOspfv3VirtIfRowStatus	1.3.6.1.4.1.89.216.9.1.12	RowStatus	read-create	This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
G32 rlOspfv3VirtIfLinkScopeLsaCount	1.3.6.1.4.1.89.216.9.1.13	Gauge32	read-only	The total number of Link-scope link state advertisements in this virtual link's link state database.
U32 rlOspfv3VirtIfLinkLsaCksumSum	1.3.6.1.4.1.89.216.9.1.14	Unsigned32	read-only	The 32-bit unsigned sum of the Link-scope link state advertisements' LS checksums contained in this virtual link's link state database. The sum can be used to determine if there has been a change in a router's link state database or to compare the link state database of two routers.
STA rlOspfv3VirtIfAdminStatus	1.3.6.1.4.1.89.216.9.1.15	Status	read-create	The desired administrative state of this virtual interface.
INT rlOspfv3VirtIfOperStatus	1.3.6.1.4.1.89.216.9.1.16	INTEGER	read-only	The current operational state of this virtual interface.
rlOspfv3NbrTable	1.3.6.1.4.1.89.216.10		not-accessible	A table describing all neighbors in the locality of the OSPFv3 router.
rlOspfv3NbrEntry	1.3.6.1.4.1.89.216.10.1		not-accessible	The information regarding a single neighbor.
RLO rlOspfv3NbrProcessId	1.3.6.1.4.1.89.216.10.1.1	RlOspfProcessID	read-only	A 32-bit integer uniquely identifying an OSPF process.
NUM rlOspfv3NbrIfIndex	1.3.6.1.4.1.89.216.10.1.2	InterfaceIndex	not-accessible	The Local Link ID of the link over which the neighbor can be reached.
OSP rlOspfv3NbrIfInstId	1.3.6.1.4.1.89.216.10.1.3	Ospfv3IfInstIdTC	not-accessible	Interface instance over which the neighbor can be reached. This ID has local link significance only.
ROU rlOspfv3NbrRtrId	1.3.6.1.4.1.89.216.10.1.4	RouterID	not-accessible	A 32-bit unsigned integer uniquely identifying the neighboring router in the Autonomous System.
IPt rlOspfv3NbrAddressType	1.3.6.1.4.1.89.216.10.1.5	InetAddressType	read-only	The address type of rlOspfv3NbrAddress. Only IPv6 addresses without zone index are expected.
IP rlOspfv3NbrAddress	1.3.6.1.4.1.89.216.10.1.6	InetAddress	read-only	The IPv6 address of the neighbor associated with the local link.
I32 rlOspfv3NbrOptions	1.3.6.1.4.1.89.216.10.1.7	Integer32	read-only	A bit mask corresponding to the neighbor's options field.
DES rlOspfv3NbrPriority	1.3.6.1.4.1.89.216.10.1.8	DesignatedRouterPriority	read-only	The priority of this neighbor in the designated- router election algorithm. The value 0 signifies that the neighbor is not eligible to become the Designated Router on this particular network.
INT rlOspfv3NbrState	1.3.6.1.4.1.89.216.10.1.9	INTEGER	read-only	The state of the relationship with this neighbor.
C32 rlOspfv3NbrEvents	1.3.6.1.4.1.89.216.10.1.10	Counter32	read-only	The number of times this neighbor relationship has changed state or an error has occurred. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of rlOspfv3DiscontinuityTime.
G32 rlOspfv3NbrLsRetransQLen	1.3.6.1.4.1.89.216.10.1.11	Gauge32	read-only	The current length of the retransmission queue.
T/F rlOspfv3NbrHelloSuppressed	1.3.6.1.4.1.89.216.10.1.12	TruthValue	read-only	Indicates whether Hellos are being suppressed to the neighbor.
NUM rlOspfv3NbrIfId	1.3.6.1.4.1.89.216.10.1.13	InterfaceIndex	read-only	The Interface ID that the neighbor advertises in its Hello packets on this link, that is, the neighbor's local interface index.
INT rlOspfv3NbrRestartHelperStatus	1.3.6.1.4.1.89.216.10.1.14	INTEGER	read-only	Indicates whether the router is acting as a graceful restart helper for the neighbor.
NUM rlOspfv3NbrRestartHelperAge	1.3.6.1.4.1.89.216.10.1.15	Ospfv3UpToRefreshIntervalTC	read-only	Remaining time in current OSPF graceful restart interval, if the router is acting as a restart helper for the neighbor.
INT rlOspfv3NbrRestartHelperExitReason	1.3.6.1.4.1.89.216.10.1.16	INTEGER	read-only	Describes the outcome of the last attempt at acting as a graceful restart helper for the neighbor. none: no restart has yet been attempted. inProgress: a restart attempt is currently underway. completed: the last restart completed successfully. timedOut: the last restart timed out. topologyChanged: the last restart was aborted due to a topology change.
NUM rlOspfv3NbrDeadTime	1.3.6.1.4.1.89.216.10.1.17	PositiveInteger	read-only	The time remaining in seconds within which we need to receive a hello packet from the neighbor or we declare the adjacency down. If fast hellos area in use, this value is always set to 1. If the oper_status is down or ospfPmNbrState is DOWN, then the value is set to zero and the field is not valid.
ARE rlOspfv3NbrAreaId	1.3.6.1.4.1.89.216.10.1.18	AreaID	read-only	The area to which the neighbor belongs. If the oper_status is down, then this value is set to zero and the field is not valid.
rlOspfv3CfgNbrTable	1.3.6.1.4.1.89.216.11		not-accessible	A table describing all configured neighbors. The Configured Neighbors table just gives OSPFv3 information for sending OSPFv3 packets to potential neighbors and is typically used on NBMA and Point-to-Multipoint networks. Once a Hello is received from a neighbor in the Configured Neighbor table, an entry for that neighbor is created in the Neighbor table and adjacency state is maintained there. Neighbors on multi-access or Point-to-Point networks can use multicast addressing, so only Neighbor table entries are created for them.
rlOspfv3CfgNbrEntry	1.3.6.1.4.1.89.216.11.1		not-accessible	The information regarding a single configured neighbor. The information in this table is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
RLO rlOspf3CfgNbrProcessId	1.3.6.1.4.1.89.216.11.1.1	RlOspfProcessID	read-only	A 32-bit integer uniquely identifying an OSPF process.
NUM rlOspfv3CfgNbrIfIndex	1.3.6.1.4.1.89.216.11.1.2	InterfaceIndex	not-accessible	The Local Link ID of the link over which the neighbor can be reached.
OSP rlOspfv3CfgNbrIfInstId	1.3.6.1.4.1.89.216.11.1.3	Ospfv3IfInstIdTC	not-accessible	Interface instance over which the neighbor can be reached. This ID has local link significance only.
IPt rlOspfv3CfgNbrAddressType	1.3.6.1.4.1.89.216.11.1.4	InetAddressType	not-accessible	The address type of rlOspfv3NbrAddress. Only IPv6 addresses without zone index are expected.
IP rlOspfv3CfgNbrAddress	1.3.6.1.4.1.89.216.11.1.5	InetAddress	not-accessible	The IPv6 address of the neighbor associated with the local link.
DES rlOspfv3CfgNbrPriority	1.3.6.1.4.1.89.216.11.1.6	DesignatedRouterPriority	read-create	The priority of this neighbor in the designated- router election algorithm. The value 0 signifies that the neighbor is not eligible to become the Designated Router on this particular network.
ROW rlOspfv3CfgNbrRowStatus	1.3.6.1.4.1.89.216.11.1.7	RowStatus	read-create	This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
rlOspfv3VirtNbrTable	1.3.6.1.4.1.89.216.12		not-accessible	A table describing all virtual neighbors.
rlOspfv3VirtNbrEntry	1.3.6.1.4.1.89.216.12.1		not-accessible	Virtual neighbor information.
RLO rlOspfv3VirtNbrProcessId	1.3.6.1.4.1.89.216.12.1.1	RlOspfProcessID	read-only	A 32-bit integer uniquely identifying an OSPF process.
ARE rlOspfv3VirtNbrArea	1.3.6.1.4.1.89.216.12.1.2	AreaID	not-accessible	The transit area Identifier.
ROU rlOspfv3VirtNbrRtrId	1.3.6.1.4.1.89.216.12.1.3	RouterID	not-accessible	A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.
NUM rlOspfv3VirtNbrIfIndex	1.3.6.1.4.1.89.216.12.1.4	InterfaceIndex	read-only	The local Interface ID for the virtual link over which the neighbor can be reached.
OSP rlOspfv3VirtNbrIfInstId	1.3.6.1.4.1.89.216.12.1.5	Ospfv3IfInstIdTC	read-only	The interface instance for the virtual link over which the neighbor can be reached.
IPt rlOspfv3VirtNbrAddressType	1.3.6.1.4.1.89.216.12.1.6	InetAddressType	read-only	The address type of rlOspfv3VirtNbrAddress. Only IPv6 addresses without zone index are expected.
IP rlOspfv3VirtNbrAddress	1.3.6.1.4.1.89.216.12.1.7	InetAddress	read-only	The IPv6 address advertised by this virtual neighbor. It must be a global scope address.
I32 rlOspfv3VirtNbrOptions	1.3.6.1.4.1.89.216.12.1.8	Integer32	read-only	A bit mask corresponding to the neighbor's options field.
INT rlOspfv3VirtNbrState	1.3.6.1.4.1.89.216.12.1.9	INTEGER	read-only	The state of the virtual neighbor relationship.
C32 rlOspfv3VirtNbrEvents	1.3.6.1.4.1.89.216.12.1.10	Counter32	read-only	The number of times this virtual link has changed its state or an error has occurred. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of rlOspfv3DiscontinuityTime.
G32 rlOspfv3VirtNbrLsRetransQLen	1.3.6.1.4.1.89.216.12.1.11	Gauge32	read-only	The current length of the retransmission queue.
T/F rlOspfv3VirtNbrHelloSuppressed	1.3.6.1.4.1.89.216.12.1.12	TruthValue	read-only	Indicates whether Hellos are being suppressed to the neighbor.
NUM rlOspfv3VirtNbrIfId	1.3.6.1.4.1.89.216.12.1.13	InterfaceIndex	read-only	The Interface ID that the neighbor advertises in its Hello packets on this virtual link, that is, the neighbor's local Interface ID.
INT rlOspfv3VirtNbrRestartHelperStatus	1.3.6.1.4.1.89.216.12.1.14	INTEGER	read-only	Indicates whether the router is acting as a graceful restart helper for the neighbor.
NUM rlOspfv3VirtNbrRestartHelperAge	1.3.6.1.4.1.89.216.12.1.15	Ospfv3UpToRefreshIntervalTC	read-only	Remaining time in the current OSPF graceful restart interval, if the router is acting as a restart helper for the neighbor.
INT rlOspfv3VirtNbrRestartHelperExitReason	1.3.6.1.4.1.89.216.12.1.16	INTEGER	read-only	Describes the outcome of the last attempt at acting as a graceful restart helper for the neighbor. none: no restart has yet been attempted. inProgress: a restart attempt is currently underway. completed: the last restart completed successfully. timedOut: the last restart timed out. topologyChanged: the last restart was aborted due to a topology change.
NUM rlOspfv3VirtNbrDeadTime	1.3.6.1.4.1.89.216.12.1.17	PositiveInteger	read-only	The time remaining in seconds within which we need to receive a hello packet from the neighbor or we declare the adjacency down. If fast hellos area in use, this value is always set to 1. If the oper_status is down or ospfPmVirtNbrState is DOWN, then the value is set to zero and the field is not valid.
rlOspfv3AreaAggregateTable	1.3.6.1.4.1.89.216.13		not-accessible	The Area Aggregate Table acts as an adjunct to the Area Table. It describes those address aggregates that are configured to be propagated from an area. Its purpose is to reduce the amount of information that is known beyond an area's borders. A range of IPv6 prefixes specified by a prefix / prefix length pair. Note that if ranges are configured such that one range subsumes another range, the most specific match is the preferred one.
rlOspfv3AreaAggregateEntry	1.3.6.1.4.1.89.216.13.1		not-accessible	A single area aggregate entry. Information in this table is persistent, and when this object is written, the entity SHOULD save the change to non-volatile storage.
RLO rlOspfv3AreaAggregateProcessId	1.3.6.1.4.1.89.216.13.1.1	RlOspfProcessID	read-only	A 32-bit integer uniquely identifying an OSPF process.
ARE rlOspfv3AreaAggregateAreaID	1.3.6.1.4.1.89.216.13.1.2	AreaID	not-accessible	The area the Address Aggregate is to be found within.
INT rlOspfv3AreaAggregateAreaLsdbType	1.3.6.1.4.1.89.216.13.1.3	INTEGER	not-accessible	The type of the Address Aggregate. This field specifies the Area LSDB type that this Address Aggregate applies to.
IPt rlOspfv3AreaAggregatePrefixType	1.3.6.1.4.1.89.216.13.1.4	InetAddressType	not-accessible	The prefix type of rlOspfv3AreaAggregatePrefix. Only IPv6 addresses are expected.
IP rlOspfv3AreaAggregatePrefix	1.3.6.1.4.1.89.216.13.1.5	InetAddress	not-accessible	The IPv6 prefix.
ADR rlOspfv3AreaAggregatePrefixLength	1.3.6.1.4.1.89.216.13.1.6	InetAddressPrefixLength	not-accessible	The length of the prefix (in bits). A prefix can not be shorter than 3 bits.
ROW rlOspfv3AreaAggregateRowStatus	1.3.6.1.4.1.89.216.13.1.7	RowStatus	read-create	This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
INT rlOspfv3AreaAggregateEffect	1.3.6.1.4.1.89.216.13.1.8	INTEGER	read-create	Prefixes subsumed by ranges will either trigger the advertisement of the indicated aggregate (advertiseMatching) or result in the prefix not being advertised at all outside the area.
U32 rlOspfv3AreaAggregateRouteTag	1.3.6.1.4.1.89.216.13.1.9	Unsigned32	read-create	This tag is advertised only in the summarized As-External LSA when summarizing from NSSA-LSAs to AS-External-LSAs.
rlOspfv3VirtLinkLsdbTable	1.3.6.1.4.1.89.216.14		not-accessible	The OSPFv3 Process's Link-scope LSDB for virtual interfaces. The LSDB contains the Link-scope link state advertisements from virtual interfaces.
rlOspfv3VirtLinkLsdbEntry	1.3.6.1.4.1.89.216.14.1		not-accessible	A single Link-scope link state advertisement for a virtual interface.
RLO rlOspfv3VirtLinkLsdbProcessId	1.3.6.1.4.1.89.216.14.1.1	RlOspfProcessID	read-only	A 32-bit integer uniquely identifying an OSPF process.
ARE rlOspfv3VirtLinkLsdbIfAreaId	1.3.6.1.4.1.89.216.14.1.2	AreaID	not-accessible	The transit area that the virtual link traverses. By definition, this is not Area 0.
ROU rlOspfv3VirtLinkLsdbIfNeighbor	1.3.6.1.4.1.89.216.14.1.3	RouterID	not-accessible	The Router ID of the virtual neighbor.
U32 rlOspfv3VirtLinkLsdbType	1.3.6.1.4.1.89.216.14.1.4	Unsigned32	not-accessible	The type of the link state advertisement. Each link state type has a separate advertisement format. Link-scope LSAs unrecognized by the router are also stored in this database.
ROU rlOspfv3VirtLinkLsdbRouterId	1.3.6.1.4.1.89.216.14.1.5	RouterID	not-accessible	The 32-bit number that uniquely identifies the originating router in the Autonomous System.
RLL rlOspfv3VirtLinkLsdbLsid	1.3.6.1.4.1.89.216.14.1.6	RlLsID	not-accessible	The Link State ID is an LS type-specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
OSP rlOspfv3VirtLinkLsdbSequence	1.3.6.1.4.1.89.216.14.1.7	Ospfv3LsaSequenceTC	read-only	The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number, the more recent the advertisement.
OSP rlOspfv3VirtLinkLsdbAge	1.3.6.1.4.1.89.216.14.1.8	Ospfv3LsaAgeTC	read-only	This field is the age of the link state advertisement in seconds. The high-order bit of the LS age field is considered the DoNotAge bit for support of on-demand circuits.
I32 rlOspfv3VirtLinkLsdbChecksum	1.3.6.1.4.1.89.216.14.1.9	Integer32	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OCT rlOspfv3VirtLinkLsdbAdvertisement	1.3.6.1.4.1.89.216.14.1.10	OCTET STRING	read-only	The entire link state advertisement, including its header.
T/F rlOspfv3VirtLinkLsdbTypeKnown	1.3.6.1.4.1.89.216.14.1.11	TruthValue	read-only	The value true (1) indicates that the LSA type is recognized by this router.
rlOspfv3NotificationEntry	1.3.6.1.4.1.89.216.15
INT rlOspfv3ConfigErrorType	1.3.6.1.4.1.89.216.15.1	INTEGER	accessible-for-notify	Potential types of configuration conflicts. Used by the rlOspfv3ConfigError and rlOspfv3ConfigVirtError notifications.
INT rlOspfv3PacketType	1.3.6.1.4.1.89.216.15.2	INTEGER	accessible-for-notify	OSPFv3 packet types.
ADR rlOspfv3PacketSrc	1.3.6.1.4.1.89.216.15.3	InetAddressIPv6	accessible-for-notify	The IPv6 address of an inbound packet that cannot be identified by a neighbor instance. Only IPv6 addresses without zone index are expected.
rlOspfv3Notifications	1.3.6.1.4.1.89.216.16
NTF rlOspfv3VirtIfStateChange	1.3.6.1.4.1.89.216.16.1			An rlOspfv3VirtIfStateChange notification signifies that there has been a change in the state of an OSPFv3 virtual interface. This notification should be generated when the interface state regresses (e.g., goes from Point-to-Point to Down) or progresses to a terminal state (i.e., Point-to-Point).
NTF rlOspfv3NbrStateChange	1.3.6.1.4.1.89.216.16.2			An rlOspfv3NbrStateChange notification signifies that there has been a change in the state of a non-virtual OSPFv3 neighbor. This notification should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., 2-Way or Full). When a neighbor transitions from or to Full on non-broadcast multi-access and broadcast networks, the notification should be generated by the Designated Router. A Designated Router transitioning to Down will be noted by ospfIfStateChange.
NTF rlOspfv3VirtNbrStateChange	1.3.6.1.4.1.89.216.16.3			An rlOspfv3VirtNbrStateChange notification signifies that there has been a change in the state of an OSPFv3 virtual neighbor. This notification should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., Full).
NTF rlOspfv3IfConfigError	1.3.6.1.4.1.89.216.16.4			An rlOspfv3IfConfigError notification signifies that a packet has been received on a non-virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a notification only if it prevents an adjacency from forming.
NTF rlOspfv3VirtIfConfigError	1.3.6.1.4.1.89.216.16.5			An rlOspfv3VirtIfConfigError notification signifies that a packet has been received on a virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a notification only if it prevents an adjacency from forming.
NTF rlOspfv3IfRxBadPacket	1.3.6.1.4.1.89.216.16.6			An rlOspfv3IfRxBadPacket notification signifies that an OSPFv3 packet that cannot be parsed has been received on a non-virtual interface.
NTF rlOspfv3VirtIfRxBadPacket	1.3.6.1.4.1.89.216.16.7			An rlOspfv3VirtIfRxBadPacket notification signifies that an OSPFv3 packet that cannot be parsed has been received on a virtual interface.
NTF rlOspfv3LsdbOverflow	1.3.6.1.4.1.89.216.16.8			An rlOspfv3LsdbOverflow notification signifies that the number of LSAs in the router's link state database has exceeded rlOspfv3ExtAreaLsdbLimit.
NTF rlOspfv3LsdbApproachingOverflow	1.3.6.1.4.1.89.216.16.9			An rlOspfv3LsdbApproachingOverflow notification signifies that the number of LSAs in the router's link state database has exceeded ninety percent of rlOspfv3ExtAreaLsdbLimit.
NTF rlOspfv3IfStateChange	1.3.6.1.4.1.89.216.16.10			An rlOspfv3IfStateChange notification signifies that there has been a change in the state of a non-virtual OSPFv3 interface. This notification should be generated when the interface state regresses (e.g., goes from DR to Down) or progresses to a terminal state (i.e., Point-to-Point, DR Other, DR, or Backup).
NTF rlOspfv3NssaTranslatorStatusChange	1.3.6.1.4.1.89.216.16.11			An rlOspfv3NssaTranslatorStatusChange notification indicates that there has been a change in the router's ability to translate OSPFv3 NSSA LSAs into OSPFv3 External LSAs. This notification should be generated when the Translator Status transitions from or to any defined status on a per-area basis.
NTF rlOspfv3RestartStatusChange	1.3.6.1.4.1.89.216.16.12			An rlOspfv3RestartStatusChange notification signifies that there has been a change in the graceful restart state for the router. This notification should be generated when the router restart status changes.
NTF rlOspfv3NbrRestartHelperStatusChange	1.3.6.1.4.1.89.216.16.13			An rlOspfv3NbrRestartHelperStatusChange notification signifies that there has been a change in the graceful restart helper state for the neighbor. This notification should be generated when the neighbor restart helper status transitions for a neighbor.
NTF rlOspfv3VirtNbrRestartHelperStatusChange	1.3.6.1.4.1.89.216.16.14			An rlOspfv3VirtNbrRestartHelperStatusChange notification signifies that there has been a change in the graceful restart helper state for the virtual neighbor. This notification should be generated when the virtual neighbor restart helper status transitions for a virtual neighbor.
I32 rlOspfv3EnableNotificationsOspfEvents	1.3.6.1.4.1.89.216.17	Integer32	read-write	A bit mask indicating enable SNMP notifications for OSPF errors. Bit 0, if set, for authenticationFailure trap. enables only the ospfIfFailure trap. Allows SNMP notifications to be sent when a packet has been received on a nonvirtual interface from a neighbor router whose authentication key or authentication type conflicts with the authentication key or authentication type of this router. Bit 1, if set, for badPacket trap. enables only the ospfIfRxBadPacket trap. Allows SNMP notifications to be sent when an OSPF packet that has not been parsed has been received on a nonvirtual interface. Bit 2, if set, for configError trap. enables only the ospfIfConfigError trap. Sends SNMP notifications when a packet has been received in a nonvirtual interface from a neighbor router whose configuration parameters conflict with the configuration parameters of this router. Bit 3, if set, for virtAuthenticationFailure trap. enables only the ospfVirtIfFailure trap. Allows SNMP notifications to be sent when a packet has been received on a virtual interface from a neighbor router whose authentication key or authentication type conflicts with the authentication key or authentication type of this router. Bit 4, if set, for virtBadPacket trap. enables only the ospfVirtIfRxBadPacket trap. Allows SNMP notifications to be sent when an OSPF packet that has not been parsed has been received on a virtual interface. Bit 5, if set, for virtConfigError trap. enables only the ospfVirtIfConfigError trap. Sends SNMP notifications when a packet has been received in a virtual interface from a neighbor router whose configuration parameters conflict with the configuration parameters of this router.
INT rlOspfv3EnableNotificationsOspfRateLimitSeconds	1.3.6.1.4.1.89.216.18	INTEGER	read-write	Sets the rate limit window size, in seconds. A number from 2 to 60. The default value is 10.
INT rlOspfv3EnableNotificationsOspfRateLimitTrapNumber	1.3.6.1.4.1.89.216.19	INTEGER	read-write	Sets the maximum number of traps sent during the window time. A number from 0 to 300. The default number is 7.

RFC description

Manages multi-instance OSPFv3 routing for IPv6 networks with enhanced OSPF features.

Start monitoring Marvell (formerly RADLAN) Layer 3 switches/routers (multi-instance OSPFv3) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RADLAN-OSPFV3-MIB