RADLAN-MIB

All MIBs › RADLAN-MIB

Category: Vendor: RADLAN/Cisco SB

Description: Root MIB module for Radlan (now part of Marvell) managed network switches, providing the base OID registrations imported by all other RADLAN-specific MIB modules.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RADLAN-MIB?

RADLAN-MIB is the foundational SNMP module for Radlan Computer Communications' embedded switch management software, now part of Marvell/Microchip and licensed to numerous OEM vendors for managed Ethernet switches. Beyond serving as the root OID registration point, it defines core objects covering bridge identity and version, error/alarm reporting, and SNMP community-based access control; administrators tracing a device's RADLAN-MIB OID back to its enterprise branch will find it anchored here. It supports monitoring hardware/software status through objects like rndBrgVersion (firmware/software version), rndBridgeAlarm and rndErrorSeverity/rndErrorDesc (fault and error conditions), and rndInactiveArpTimeOut (ARP aging behavior). It underlies dozens of vendor-specific RADLAN-derived MIBs that extend it for VLANs, QoS, and port management, so it depends only lightly on SNMPv2-SMI itself while being a near-universal import for other rnd*-prefixed modules. It is typically deployed on low-to-mid-range managed Ethernet switches from OEMs that license the Radlan switch software stack.

IPNetwork Monitor allows you to monitor SNMP objects defined in RADLAN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Radlan/Marvell-licensed managed Ethernet switches
OEM switches built on the Radlan switch software stack

Monitoring Examples

An administrator can poll rndBrgVersion to confirm the switch's software/firmware build during an audit, and monitor rndBridgeAlarm alongside rndErrorSeverity and rndErrorDesc to catch and triage internal fault conditions raised by the switch's embedded agent. The rndCommunityTable (rndCommunityEntry rows keyed by rndCommunityMngStationAddr) lets an operator audit which management stations hold read/write access (rndCommunityAccess) via a given rndCommunityString, revealing unauthorized or stale SNMP community entries. rndInactiveArpTimeOut monitoring helps validate ARP table aging configuration on the device.

What Can Be Monitored

bridge software/firmware version
error severity and description
bridge alarm status
SNMP community access table
ARP inactivity timeout

Imported Objects

From BRIDGE-MIB

BridgeId
MacAddress
Timeout
dot1dBasePort	OBJECT-TYPE
dot1dBasePortEntry	OBJECT-TYPE

From IEEE8021-PAE-MIB

PaeControlledPortStatus
dot1xAuthSessionStatsEntry	OBJECT-TYPE
dot1xPaePortNumber	OBJECT-TYPE

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From P-BRIDGE-MIB

EnabledStatus

From Q-BRIDGE-MIB

PortList
VlanIndex
dot1qFdbId	OBJECT-TYPE

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
IpAddress
TimeTicks
enterprises

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Counter32
Counter64
Unsigned32

From SNMPv2-SMI-v1

Counter-32
Integer-32
Unsigned-32

From SNMPv2-TC-v1

DateAndTime
DisplayString
PhysAddress
RowPointer
RowStatus
TimeInterval
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
NTF abortTftp	1.3.6.1.4.1.89.0.13			This trap indicates that in the device aborted a TFTP session with the management station. Variable rndErrorDesc and rndErrorSeverity provides the actual message text and severity respectively.
NTF autoConfigurationCompleted	1.3.6.1.4.1.89.0.50			This trap indicates that auto comfiguration completetd succssefully. The bound variable rndErrorDesc, rndErrorSeverity(== info )
NTF bpduGuardPortSuspended	1.3.6.1.4.1.89.0.202			Warning trap indicating - Port was suspended because there was BPDU Guard violation.
NTF chapFailedCommunication	1.3.6.1.4.1.89.0.140
dlPrivate	1.3.6.1.4.1.89.119
NTF dstrSysLog	1.3.6.1.4.1.89.0.175			Master receive trap from slave , and forward it as trap
NTF endTftp	1.3.6.1.4.1.89.0.12			This trap indicates that in the device finished a TFTP transaction with the management station. variable rndErrorDesc and rndErrorSeverity provides the actual message text and severity respectively.
NTF errorsDuringInit	1.3.6.1.4.1.89.0.61			This trap indicates that the an error occured during initialization The bound variable rndErrorDesc, rndErrorSeverity(== error )
NTF facsAccessVoilation	1.3.6.1.4.1.89.0.49			This trap indicates that message that fits FACS statenebt with operation blockAndReport was forward to the interface. The bound variable rndErrorDesc, rndErrorSeverity(== info ) and interface Number.
NTF faultBackUp	1.3.6.1.4.1.89.0.23			Automantic switchover to backup link because of main link fault.
NTF forwardingTabOverflow	1.3.6.1.4.1.89.0.51			This trap indicates that an overflow condition has occurred in the layer II Forward Table. The bound variable rndErrorDesc, rndErrorSeverity(== warning )
NTF framRelaySwitchConnectionDown	1.3.6.1.4.1.89.0.54			This trap indicates that a connection between the Frame Relay Switch and the WanGate failed. The bound variable rndErrorDesc, rndErrorSeverity(== warning )
NTF framRelaySwitchConnectionUp	1.3.6.1.4.1.89.0.53			This trap indicates that a connection establish between the Frame relay Switch and the WanGate. The bound variable rndErrorDesc, rndErrorSeverity(== warning )
NTF frDLCIStatudChange	1.3.6.1.4.1.89.0.138
genGroup	1.3.6.1.4.1.89.2.11
STR genGroupConfigurationSymbol	1.3.6.1.4.1.89.2.11.2	DisplayString	read-only	Defines the Configuration Symbol attached to any hardware module manufactured by LANNET. One single character A..Z defines the CS version.
INT genGroupHWStatus	1.3.6.1.4.1.89.2.11.3	INTEGER	read-only	This attribute describes the status of the group hardware as detected by the sensors software.
STR genGroupHWVersion	1.3.6.1.4.1.89.2.11.1	DisplayString	read-only	Defines the HW version of the product.
ipSpec	1.3.6.1.4.1.89.26
NTF ipxRipTblOverflow	1.3.6.1.4.1.89.0.36			This trap indicates that in an OpenGate IPX RIP table overflow. The bound variable rndErrorDesc, rndErrorSeverity provides the actual message text and severity respectively.
NTF ipxSapTblOverflow	1.3.6.1.4.1.89.0.37			This trap indicates that in an OpenGate IPX SAP table overflow. The bound variable rndErrorDesc, rndErrorSeverity provides the actual message text and severity respectively.
NTF mainLinkUp	1.3.6.1.4.1.89.0.24			Communication returened to main link.
NTF papFailedCommunication	1.3.6.1.4.1.89.0.139
NTF pppSecurityViolation	1.3.6.1.4.1.89.0.137			This trap indicates that a PPP link got an unrecognized secret. The bound variables rndErrorDesc, rndErrorSeverity(== warning ), interface Number. and pppSecurityIdentity
NTF resetRequired	1.3.6.1.4.1.89.0.10			This trap indicates that in order to perform the last SET request, a reset operation of the router/bridge is required. This occurs when the layer 2 routing algorithm is changed between SPF and Spanning Tree. The reset can be performed manually or using the variable rndAction.
rl3sw2swTables	1.3.6.1.4.1.89.63
INT rl3sw2swTablesPollingInterval	1.3.6.1.4.1.89.63.1	INTEGER	read-write	The polling interval for dynamic 3SW/2SW tables in seconds.
rlAAA	1.3.6.1.4.1.89.79
rlAAAEap	1.3.6.1.4.1.89.97
NTF rlAAAUserLocked	1.3.6.1.4.1.89.0.194			Warning trap indicating that the user was locked after number of consecutives unsuccessful login attempts.
rlAgentsCapabilitiesGroups	1.3.6.1.4.1.89.72
rlAggregateSubVlanEntry	1.3.6.1.4.1.89.73.3.1		not-accessible	The row definition for this table.
NUM rlAggregateSubVlanIfIndex	1.3.6.1.4.1.89.73.3.1.1	InterfaceIndex	read-only	Indicate the subVlan that allocated to the aggregate vlan
ROW rlAggregateSubVlanStatus	1.3.6.1.4.1.89.73.3.1.2	RowStatus	read-write	The status of the aggregateSubVlan table entry. It's used to delete an entry
rlAggregateSubVlanTable	1.3.6.1.4.1.89.73.3		not-accessible	The table indicates all the allocated sub-vlans to the aggregateVlans, an entry in the rlAggregateVlanTable must be exist before allocating the subVlans
rlAggregateVlan	1.3.6.1.4.1.89.73
INT rlAggregateVlanArpProxy	1.3.6.1.4.1.89.73.4	INTEGER	read-write	When ARP Proxy is enabled, the router can respond to ARP requests for nodes located on different sub-vlans, which belong to the same Super VLAN.The router responds with its own MAC address. When ARP Proxy is disabled, the router responds only to ARP requests for its own IP addresses.
rlAggregateVlanEntry	1.3.6.1.4.1.89.73.2.1		not-accessible	The row definition for this table.
NUM rlAggregateVlanIndex	1.3.6.1.4.1.89.73.2.1.1	InterfaceIndex	not-accessible	This index indicate the aggrigateVlan id, the aggregate vlan index is starting from 10000
INT rlAggregateVlanMibVersion	1.3.6.1.4.1.89.73.1	INTEGER	read-only	MIB's version, the current version is 1.
STR rlAggregateVlanName	1.3.6.1.4.1.89.73.2.1.2	DisplayString	read-write	The name of the aggregateVlan
INT rlAggregateVlanPhysAddressType	1.3.6.1.4.1.89.73.2.1.3	INTEGER	read-write	This variable indicates whether the physical address assigned to this VLAN should be the default one or be chosen from the set of reserved physical addresses of the device.
ROW rlAggregateVlanStatus	1.3.6.1.4.1.89.73.2.1.4	RowStatus	read-write	The status of the aggregateVlan table entry. It's used to delete an entry
rlAggregateVlanTable	1.3.6.1.4.1.89.73.2		not-accessible	The table creates an aggregateVlans, the IfIndex is from 10000
rlAmap	1.3.6.1.4.1.89.106
rlArpSpoofing	1.3.6.1.4.1.89.60
rlArpSpoofingEntry	1.3.6.1.4.1.89.60.2.1		not-accessible	An entry of this table specifis ifIndex,IP Address and MAC address.
NUM rlArpSpoofingIfIndex	1.3.6.1.4.1.89.60.2.1.1	InterfaceIndex	read-write	The physical interface for which this entry contains information.
IP rlArpSpoofingLocalIpAddr	1.3.6.1.4.1.89.60.2.1.2	IpAddress	read-write	Ip addres for which the device will send ARP reply (ARP spoofing).
PHY rlArpSpoofingMacAddr	1.3.6.1.4.1.89.60.2.1.3	PhysAddress	read-write	MAC addres with which the device will send ARP reply. If the field is ommited or its value 0.0.0.0 the device will send with the interface's MAC address.
INT rlArpSpoofingMibVersion	1.3.6.1.4.1.89.60.1	INTEGER	read-only	MIB's version, the current version is 1.
NUM rlArpSpoofingOutPhysIfIndex	1.3.6.1.4.1.89.60.2.1.5	InterfaceIndexOrZero	read-write	The physical interface to which the device will send periodically ARP requests if its value differs from 0. If its value is 0 then ARP requests will send to all the VLAN's ports.
IP rlArpSpoofingRemoteIpAddr	1.3.6.1.4.1.89.60.2.1.4	IpAddress	read-write	Ip addres for which the device will send periodically ARP requests if its value differs from 0.0.0.0.
ROW rlArpSpoofingStatus	1.3.6.1.4.1.89.60.2.1.6	RowStatus	read-write	It is used to insert, update or delete an entry
rlArpSpoofingTable	1.3.6.1.4.1.89.60.2		not-accessible	A list of the ifIndexes, IP addresses and corresponding MAC addresses.
rlAutoUpdate	1.3.6.1.4.1.89.123
rlBgp	1.3.6.1.4.1.89.71
rlBonjour	1.3.6.1.4.1.89.114
NTF rlBrgMacAddFailedTrap	1.3.6.1.4.1.89.0.183			Informational trap indicating that adding dynamic mac/s failed due to full hash chain.
INT rlBrgMacSwAdminTrapFrequency	1.3.6.1.4.1.89.50.12	INTEGER	read-write	This variable indicates the minimal frequency (in seconds) of sending a trap. It is relevant only when trap is enabled.
INT rlBrgMacSwDynamicTables	1.3.6.1.4.1.89.50.3	INTEGER	read-only	Specifies whether the device supports port dynamic MAC tables.
rlBrgMacSwitch	1.3.6.1.4.1.89.50
INT rlBrgMacSwKeyType	1.3.6.1.4.1.89.50.7	INTEGER	read-only	Specified the used MAC Address Table kye format: macOnly: One global MAC Address Table per device (leaky VLANs). tagAndMac: MAC Address Table per each VLAN (strick VLANs).
INT rlBrgMacSwMaxTableNumber	1.3.6.1.4.1.89.50.2	INTEGER	read-only	Maximum number of MAC Tables supported by the device.
INT rlBrgMacSwOldEntryDeleteMode	1.3.6.1.4.1.89.50.5	INTEGER	read-only	The method used to delete old unused entries refresh_flag: The high level sets a flag when it adds or updates an entry, the Switch clears the flag each time, when it learns the station once more. aging_flag: The high level clears a flag when it adds or updates an entry, the Switch sets the flag each time, when it learns the station once more. aging_time: The high level defines a timeout, the Switch sends a message to the high level each time when the station doesn't send messages during interval between timeout and 2*timeout. Boundaries: The Switch doesn't support any mechanism, and the high level uses two boundaries: red and yellow. When the number of entries exceeds the red boundary, the high level deletes the oldest entries.
INT rlBrgMacSwOperTrapCount	1.3.6.1.4.1.89.50.11	INTEGER	read-only	This variable indicates the trap counter status (i.e. number of received MAC addresses since the last trap sent that haven't been inserted into the hash). It is relevant only when trap is enabled.
INT rlBrgMacSwRedBoundary	1.3.6.1.4.1.89.50.9	INTEGER	read-write	The yellow boundary.
INT rlBrgMacSwSpanningTree	1.3.6.1.4.1.89.50.6	INTEGER	read-only	Specifies whether the device supports port the Spanning Tree Protocol.
T/F rlBrgMacSwTrapEnable	1.3.6.1.4.1.89.50.10	TruthValue	read-write	This variable indicates whether to create a SNMP trap if adding dynamic mac failed due to full hash chain.
INT rlBrgMacSwVersion	1.3.6.1.4.1.89.50.1	INTEGER	read-only	MIB's version, the current version is 2.
INT rlBrgMacSwYellowBoundary	1.3.6.1.4.1.89.50.8	INTEGER	read-write	The yellow boundary.
rlBrgMcMngr	1.3.6.1.4.1.89.117
rlBrgMulticast	1.3.6.1.4.1.89.116
rlBridgeSecurity	1.3.6.1.4.1.89.112
rlBroadcom	1.3.6.1.4.1.89.68
rlCDB	1.3.6.1.4.1.89.94
rlCli	1.3.6.1.4.1.89.52
T/F rlCliFileEnable	1.3.6.1.4.1.89.52.4	TruthValue	read-only	CLI File Enable/Disable
T/F rlCliFileEnableAfterReset	1.3.6.1.4.1.89.52.5	TruthValue	read-write	CLI File Enable/Disable After Reset
INT rlCliMibVersion	1.3.6.1.4.1.89.52.1	INTEGER	read-only	MIB's version, the current version is 1.
STR rlCliPassword	1.3.6.1.4.1.89.52.2	DisplayString	read-write	CLI Password
INT rlCliTimer	1.3.6.1.4.1.89.52.3	INTEGER	read-write	CLI Timer
rlCopy	1.3.6.1.4.1.89.87
rlCpuCounters	1.3.6.1.4.1.89.124
IP rlDhcpApprovalActionAddress	1.3.6.1.4.1.89.76.6.1.2	IpAddress	read-only	IP Address.
T/F rlDhcpApprovalActionApprove	1.3.6.1.4.1.89.76.6.1.4	TruthValue	read-write	Approve or decline ip address.
rlDhcpApprovalActionEntry	1.3.6.1.4.1.89.76.6.1		not-accessible	An entry in rlDhcpApprovalActionTable.
NUM rlDhcpApprovalActionIfIndex	1.3.6.1.4.1.89.76.6.1.1	InterfaceIndex	read-only	IP interface ifIndex.
IP rlDhcpApprovalActionMask	1.3.6.1.4.1.89.76.6.1.3	IpAddress	read-only	IP Address mask.
rlDhcpApprovalActionTable	1.3.6.1.4.1.89.76.6		not-accessible	Action for waiting ip address (approve/decline).
T/F rlDhcpApprovalEnabled	1.3.6.1.4.1.89.76.4	TruthValue	read-only	DHCP Approval feature status - enable (True) or desable (False). Must be True only if DHCP Approval supported, device has only one ip interface and default ip exist.
IP rlDhcpApprovalWaitingAddress	1.3.6.1.4.1.89.76.5.1.2	IpAddress	read-only	IP Address waiting for approval.
rlDhcpApprovalWaitingEntry	1.3.6.1.4.1.89.76.5.1		not-accessible	An entry in rlDhcpApprovalWaitingTable.
IP rlDhcpApprovalWaitingGateway	1.3.6.1.4.1.89.76.5.1.4	IpAddress	read-only	Default gateway of received address.
NUM rlDhcpApprovalWaitingIfIndex	1.3.6.1.4.1.89.76.5.1.1	InterfaceIndex	read-only	IP interface ifIndex.
IP rlDhcpApprovalWaitingMask	1.3.6.1.4.1.89.76.5.1.3	IpAddress	read-only	Mask waiting for approval.
rlDhcpApprovalWaitingTable	1.3.6.1.4.1.89.76.5		not-accessible	IP addresses waiting for approval.
rlDhcpCl	1.3.6.1.4.1.89.76
rlDhcpClActionEntry	1.3.6.1.4.1.89.76.3.1		not-accessible	An entry (conceptual row) in dhcpClActionTable.
STR rlDhcpClActionHostName	1.3.6.1.4.1.89.76.3.1.3	SnmpAdminString	read-write	This option specifies the name of the client.
NUM rlDhcpClActionIfIndex	1.3.6.1.4.1.89.76.3.1.1	InterfaceIndex	read-only	The interface which the action is implemented for or NULL if it implemented for all device.
ROW rlDhcpClActionStatus	1.3.6.1.4.1.89.76.3.1.2	RowStatus	read-write	The status of this entry. Creating the entry renewing Dhcp address on the interface; destroying the entry release Dhcp address on the interface.
rlDhcpClActionTable	1.3.6.1.4.1.89.76.3		not-accessible	The (conceptual) table mentione IP address which must be released/renewed on the interface.
INT rlDhcpClCommandAction	1.3.6.1.4.1.89.76.7.1.2	INTEGER	read-write	Action to apply.
rlDhcpClCommandEntry	1.3.6.1.4.1.89.76.7.1		not-accessible	The row definition for this table.
rlDhcpClCommandTable	1.3.6.1.4.1.89.76.7		read-only	Action MIB for DHCP Renew command.
rlDhcpSpoofing	1.3.6.1.4.1.89.113
rlDigitalKeyManage	1.3.6.1.4.1.89.86
rlDnsCl	1.3.6.1.4.1.89.93
OCT rldot1dDeviceCapabilities	1.3.6.1.4.1.89.57.3.2	OCTET STRING	read-only	Indicates the optional parts of private extension of IEEE 802.1D and 802.1Q that are implemented by this device and are manageable through this MIB. Capabilities that are allowed on a per-port basis are indicated in dot1dPortCapabilities.
rldot1dExtBase	1.3.6.1.4.1.89.57.3
INT rldot1dExtBaseMibVersion	1.3.6.1.4.1.89.57.3.1	INTEGER	read-only	MIB's version, the current version is 1.
rldot1dPriority	1.3.6.1.4.1.89.57.1
INT rldot1dPriorityMibVersion	1.3.6.1.4.1.89.57.1.1	INTEGER	read-only	MIB's version, the current version is 1.
rldot1dPriorityPortGroupEntry	1.3.6.1.4.1.89.57.1.2.1		not-accessible	All ports belonging to a same group have the same User Priority to Traffic Class mapping.
INT rldot1dPriorityPortGroupNumber	1.3.6.1.4.1.89.57.1.2.1.1	INTEGER	read-only	A group, that port belongs to. All ports belonging to a same group have the same User Priority to Traffic Class mapping.
rldot1dPriorityPortGroupTable	1.3.6.1.4.1.89.57.1.2		not-accessible	A list of PortGroupNumber for each port.
rldot1dStp	1.3.6.1.4.1.89.57.2
INT rldot1dStpBpduCount	1.3.6.1.4.1.89.57.2.11	INTEGER	read-write	The number of bpdu that need to received for the link to be considered stable.
INT rldot1dStpBpduType	1.3.6.1.4.1.89.57.2.13.1.8	INTEGER	read-only	Specified the type of BPDU transmitted by this port.
BRI rldot1dStpDesignatedRoot	1.3.6.1.4.1.89.57.2.6.1.5	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
T/F rldot1dStpEdgeportSupportInStp	1.3.6.1.4.1.89.57.2.20	TruthValue	read-only	If EdgePort is supported in stpCompatible mode .
T/F rldot1dStpEnable	1.3.6.1.4.1.89.57.2.3	TruthValue	read-write	Enable / Disable spanning tree. When working in per vlan mode enable / disable STP per all vlans.
T/F rldot1dStpEnableByDefault	1.3.6.1.4.1.89.57.2.17	TruthValue	read-only	The default value of rldot1dStpEnable .
T/F rldot1dStpExtendedPortNumberFormat	1.3.6.1.4.1.89.57.2.5	TruthValue	read-write	Specifies whether the STP uses the extended port fnumber format.
T/F rldot1dStpFilterBpdu	1.3.6.1.4.1.89.57.2.21	TruthValue	read-write	Specified if the device should filter BPDUs when STP is disabled.
INT rldot1dStpFloodBpduMethod	1.3.6.1.4.1.89.57.2.22	INTEGER	read-write	Specified flooding method: 1 - classic - untagged to all stp disabled ports 2 - bridging -normal bridging.
TIM rldot1dStpForwardDelay	1.3.6.1.4.1.89.57.2.6.1.11	Timeout	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
TIM rldot1dStpHelloTime	1.3.6.1.4.1.89.57.2.6.1.9	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
INT rldot1dStpHoldTime	1.3.6.1.4.1.89.57.2.6.1.10	INTEGER	read-only	This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
TIK rldot1dStpLastChanged	1.3.6.1.4.1.89.57.2.12	TimeTicks	read-only	The last time any object in this table was changed by SNMP or other local management means.
TIM rldot1dStpMaxAge	1.3.6.1.4.1.89.57.2.6.1.8	Timeout	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
INT rldot1dStpMibVersion	1.3.6.1.4.1.89.57.2.1	INTEGER	read-only	MIB's version, the current version is 2.
INT rldot1dStpMonitorTime	1.3.6.1.4.1.89.57.2.10	INTEGER	read-write	Factor of hello-time during which a port is monotored to determine if it is stable.
T/F rldot1dStpPortAutoEdgePort	1.3.6.1.4.1.89.57.2.13.1.10	TruthValue	read-write	If TRUE causes the Port when become up, to enter the blocking state, and if during 3 seconds it doesn't receive a BPDU, it will enter the forwarding state.
T/F rldot1dStpPortBelongToVlanDefault	1.3.6.1.4.1.89.57.2.16	TruthValue	read-only	The default value of rldot1dStpPortMustBelongToVlan .
T/F rldot1dStpPortBpduGuardEnable	1.3.6.1.4.1.89.57.2.24.1.1	TruthValue	read-write	Specified if bpdu guard is enabled on this port.
rldot1dStpPortBpduGuardEntry	1.3.6.1.4.1.89.57.2.24.1		not-accessible	A list of information maintained by every port whether it is bpdu guard.
rldot1dStpPortBpduGuardTable	1.3.6.1.4.1.89.57.2.24		not-accessible	A table that contains for each port whether it is bpdu guard .
C32 rldot1dStpPortBpduReceived	1.3.6.1.4.1.89.57.2.13.1.6	Counter_32	read-only	Specified the number of bpdu received in this port.
C32 rldot1dStpPortBpduSent	1.3.6.1.4.1.89.57.2.13.1.5	Counter_32	read-only	Specified the number of bpdu sent from this port.
T/F rldot1dStpPortDampEnable	1.3.6.1.4.1.89.57.2.13.1.2	TruthValue	read-write	Specified if dampening is enabled on this port.
T/F rldot1dStpPortDampStable	1.3.6.1.4.1.89.57.2.13.1.3	TruthValue	read-only	Specified if the port is stable.
rldot1dStpPortEntry	1.3.6.1.4.1.89.57.2.13.1		not-accessible	A list of information maintained by every port about the Spanning Tree Protocol state for that port.
T/F rldot1dStpPortFilterBpdu	1.3.6.1.4.1.89.57.2.13.1.4	TruthValue	read-write	Specified if this port should filter bpdus when stp is disabled.
T/F rldot1dStpPortLoopback	1.3.6.1.4.1.89.57.2.13.1.11	TruthValue	read-only	Specified loopback was detected on port.
T/F rldot1dStpPortMustBelongToVlan	1.3.6.1.4.1.89.57.2.4	TruthValue	read-write	Specifies whether a port must belong to a VLAN in order to participate in the STP.
INT rldot1dStpPortPort	1.3.6.1.4.1.89.57.2.13.1.1	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
T/F rldot1dStpPortRestrictedRole	1.3.6.1.4.1.89.57.2.13.1.9	TruthValue	read-write	If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even if it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected.
INT rldot1dStpPortRole	1.3.6.1.4.1.89.57.2.13.1.7	INTEGER	read-only	Specified the role of this this port.
T/F rldot1dStpPortsEnable	1.3.6.1.4.1.89.57.2.14	TruthValue	read-only	Enable / Disable spanning tree on ports by default .
NTF rldot1dStpPortStateForwarding	1.3.6.1.4.1.89.0.151			The trap is sent by a bridge when any of its configured ports transitions from the Learning state to the Forwarding state.
NTF rldot1dStpPortStateNotForwarding	1.3.6.1.4.1.89.0.152			The trap is sent by a bridge when any of its configured ports transitions from the Forwarding state to the Blocking state.
rldot1dStpPortTable	1.3.6.1.4.1.89.57.2.13		not-accessible	A table that contains extended pair port specific information.
INT rldot1dStpPortToDefault	1.3.6.1.4.1.89.57.2.18	INTEGER	read-write	To order port/s to revert to default setings .
INT rldot1dStpRootCost	1.3.6.1.4.1.89.57.2.6.1.6	INTEGER	read-only	The cost of the path to the root as seen from this bridge.
INT rldot1dStpRootPort	1.3.6.1.4.1.89.57.2.6.1.7	INTEGER	read-only	The port number of the port which offers the lowest cost path from this bridge to the root bridge.
rldot1dStpSeparatedBridges	1.3.6.1.4.1.89.57.2.23
T/F rldot1dStpSeparatedBridgesAutoConfig	1.3.6.1.4.1.89.57.2.23.3	TruthValue	read-write	Enable / Disable Separated Bridges Automatic Configuration.
T/F rldot1dStpSeparatedBridgesEnable	1.3.6.1.4.1.89.57.2.23.2	TruthValue	read-write	Enable / Disable Separated Bridges Feature.
rldot1dStpSeparatedBridgesEntry	1.3.6.1.4.1.89.57.2.23.1.1		not-accessible	Defines the contents of each line in the rlSeparatedBridgesTable table.
T/F rldot1dStpSeparatedBridgesPortEnable	1.3.6.1.4.1.89.57.2.23.1.1.1	TruthValue	read-write	This variable indicates whether the separated bridge feature is enabled on a specified ifIndex.
rldot1dStpSeparatedBridgesTable	1.3.6.1.4.1.89.57.2.23.1		not-accessible	Define if separated bridges feature is enabled for each interface.
INT rldot1dStpSupportedType	1.3.6.1.4.1.89.57.2.19	INTEGER	read-only	The type of stp supported by the device.
T/F rldot1dStpTaggedFlooding	1.3.6.1.4.1.89.57.2.15	TruthValue	read-only	flooding can be done in tagged bpdu .
TIK rldot1dStpTimeSinceTopologyChange	1.3.6.1.4.1.89.57.2.6.1.3	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
CTR rldot1dStpTopChanges	1.3.6.1.4.1.89.57.2.6.1.4	Counter	read-only	The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
rldot1dStpTrapVariable	1.3.6.1.4.1.89.57.2.8
NUM rldot1dStpTrapVrblifIndex	1.3.6.1.4.1.89.57.2.8.1	InterfaceIndex	read-only	The ifIndex of port which STP status was changed
INT rldot1dStpTrapVrblVID	1.3.6.1.4.1.89.57.2.8.2	INTEGER	read-only	The VID of VLAN to which the port belongs which STP status was changed
INT rldot1dStpType	1.3.6.1.4.1.89.57.2.2	INTEGER	read-only	Specifies whether the device supports Spanning Tree per device, or per group.
INT rldot1dStpTypeAfterReset	1.3.6.1.4.1.89.57.2.9	INTEGER	read-write	New mode of spaning tree supported by the device after the next reset.
INT rldot1dStpVlan	1.3.6.1.4.1.89.57.2.6.1.1	INTEGER	read-only	The Vlan index.
T/F rldot1dStpVlanEnable	1.3.6.1.4.1.89.57.2.6.1.2	TruthValue	read-write	Specifies whether this vlan is STP enable or disable
rldot1dStpVlanEntry	1.3.6.1.4.1.89.57.2.6.1		not-accessible	A list of information maintained by every Vlan about the Spanning Tree Protocol state for that Vlan.
BRI rldot1dStpVlanPortDesignatedBridge	1.3.6.1.4.1.89.57.2.7.1.9	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
INT rldot1dStpVlanPortDesignatedCost	1.3.6.1.4.1.89.57.2.7.1.8	INTEGER	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
OCT rldot1dStpVlanPortDesignatedPort	1.3.6.1.4.1.89.57.2.7.1.10	OCTET STRING	read-only	The Port Identifier of the port on the Designated Bridge for this port's segment.
BRI rldot1dStpVlanPortDesignatedRoot	1.3.6.1.4.1.89.57.2.7.1.7	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
INT rldot1dStpVlanPortEnable	1.3.6.1.4.1.89.57.2.7.1.5	INTEGER	read-write	The enabled/disabled status of the port.
rldot1dStpVlanPortEntry	1.3.6.1.4.1.89.57.2.7.1		not-accessible	A list of information maintained by every pair about the Spanning Tree Protocol state for that pair.
CTR rldot1dStpVlanPortForwardTransitions	1.3.6.1.4.1.89.57.2.7.1.11	Counter	read-only	The number of times this port has transitioned from the Learning state to the Forwarding state.
INT rldot1dStpVlanPortPathCost	1.3.6.1.4.1.89.57.2.7.1.6	INTEGER	read-write	The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
INT rldot1dStpVlanPortPort	1.3.6.1.4.1.89.57.2.7.1.2	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
INT rldot1dStpVlanPortPriority	1.3.6.1.4.1.89.57.2.7.1.3	INTEGER	read-write	The value of the priority field which is contained in the more significant 4 bits of the most significant octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of rldot1dStpVlanPort.
INT rldot1dStpVlanPortState	1.3.6.1.4.1.89.57.2.7.1.4	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpVlanPortEnable), this object will have a value of disabled(1).
rldot1dStpVlanPortTable	1.3.6.1.4.1.89.57.2.7		not-accessible	A table that contains pair specific information for the Spanning Tree Protocol.
INT rldot1dStpVlanPortVlan	1.3.6.1.4.1.89.57.2.7.1.1	INTEGER	read-only	The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information.
rldot1dStpVlanTable	1.3.6.1.4.1.89.57.2.6		not-accessible	A table that contains vlan-specific information for the Spanning Tree Protocol.
rldot1dTpAgingTime	1.3.6.1.4.1.89.57.7
INT rldot1dTpAgingTimeMax	1.3.6.1.4.1.89.57.7.2	INTEGER	read-only	The max timeout period in seconds for aging out dynamically learned forwarding information.
INT rldot1dTpAgingTimeMin	1.3.6.1.4.1.89.57.7.1	INTEGER	read-only	The min timeout period in seconds for aging out dynamically learned forwarding information.
rldot1pPriorityMap	1.3.6.1.4.1.89.57.5
rldot1pPriorityMapEntry	1.3.6.1.4.1.89.57.5.2.1		not-accessible	The row definition for this table.
STR rldot1pPriorityMapName	1.3.6.1.4.1.89.57.5.2.1.1	DisplayString	read-only	The map name
POR rldot1pPriorityMapPort	1.3.6.1.4.1.89.57.5.2.1.3	PortList	read-write	the port that the map, is applied on in config
POR rldot1pPriorityMapPortList	1.3.6.1.4.1.89.57.5.2.1.4	PortList	read-only	the ports that the map, is applied on in actual
OCT rldot1pPriorityMapPriority	1.3.6.1.4.1.89.57.5.2.1.2	OCTET STRING	read-write	The map holding the queue
INT rldot1pPriorityMapState	1.3.6.1.4.1.89.57.5.1	INTEGER	read-write	enable / disable
ROW rldot1pPriorityMapStatus	1.3.6.1.4.1.89.57.5.2.1.5	RowStatus	read-write	The status of the table entry. It's used to delete an entry
rldot1pPriorityMapTable	1.3.6.1.4.1.89.57.5.2		not-accessible	This table hold information the priority maps
rldot1sMstp	1.3.6.1.4.1.89.57.6
STR rldot1sMstpConfigurationName	1.3.6.1.4.1.89.57.6.4	SnmpAdminString	read-only	The active configuration name as will be caried in MST BPDU's.
INT rldot1sMstpDesignatedMaxHopes	1.3.6.1.4.1.89.57.6.8	INTEGER	read-only	Max number of hopes that an MST BPDU will travel inside a region.
T/F rldot1sMstpExtPortBoundary	1.3.6.1.4.1.89.57.6.7.1.5	TruthValue	read-only	Indication if the port is conented to to a lan segment outside or inside the region.
INT rldot1sMstpExtPortDesignatedRegionalCost	1.3.6.1.4.1.89.57.6.7.1.4	INTEGER	read-only	The regional path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
BRI rldot1sMstpExtPortDesignatedRegionalRoot	1.3.6.1.4.1.89.57.6.7.1.3	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
rldot1sMstpExtPortEntry	1.3.6.1.4.1.89.57.6.7.1		not-accessible	A list of information maintained by every port of the CIST.
INT rldot1sMstpExtPortInternalAdminPathCost	1.3.6.1.4.1.89.57.6.7.1.6	INTEGER	read-write	The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object dot1dStpPortPathCost, which returns the operational value of the path cost.
INT rldot1sMstpExtPortInternalOperPathCost	1.3.6.1.4.1.89.57.6.7.1.2	INTEGER	read-only	The contribution of this port to the path cost of paths towards the spanning tree regional root which include this port. 802.1S-2002 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
INT rldot1sMstpExtPortPort	1.3.6.1.4.1.89.57.6.7.1.1	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
rldot1sMstpExtPortTable	1.3.6.1.4.1.89.57.6.7		not-accessible	A table that contains MSTP information about ports of the CIST.
INT rldot1sMstpGroup	1.3.6.1.4.1.89.57.6.6.1.2	INTEGER	read-only	Specifid the active group number this vlan belonges to.
BRI rldot1sMstpInstanceDesignatedRoot	1.3.6.1.4.1.89.57.6.1.1.5	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Muliple Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
T/F rldot1sMstpInstanceEnable	1.3.6.1.4.1.89.57.6.1.1.2	TruthValue	read-only	Specifies whether this Instance is STP enable or disable
rldot1sMstpInstanceEntry	1.3.6.1.4.1.89.57.6.1.1		not-accessible	A list of information maintained by every instance about the multiple Spanning Tree Protocol state for that instance.
TIM rldot1sMstpInstanceForwardDelay	1.3.6.1.4.1.89.57.6.1.1.11	Timeout	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
TIM rldot1sMstpInstanceHelloTime	1.3.6.1.4.1.89.57.6.1.1.9	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
INT rldot1sMstpInstanceHoldTime	1.3.6.1.4.1.89.57.6.1.1.10	INTEGER	read-only	This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
INT rldot1sMstpInstanceId	1.3.6.1.4.1.89.57.6.1.1.1	INTEGER	read-only	The Instance index.
TIM rldot1sMstpInstanceMaxAge	1.3.6.1.4.1.89.57.6.1.1.8	Timeout	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
INT rldot1sMStpInstancePortAdminPathCost	1.3.6.1.4.1.89.57.6.2.1.12	INTEGER	read-write	The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object dot1dStpPortPathCost, which returns the operational value of the path cost.
BRI rldot1sMstpInstancePortDesignatedBridge	1.3.6.1.4.1.89.57.6.2.1.9	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
INT rldot1sMstpInstancePortDesignatedCost	1.3.6.1.4.1.89.57.6.2.1.8	INTEGER	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
OCT rldot1sMstpInstancePortDesignatedPort	1.3.6.1.4.1.89.57.6.2.1.10	OCTET STRING	read-only	The Port Identifier of the port on the Designated Bridge for this port's segment.
BRI rldot1sMstpInstancePortDesignatedRoot	1.3.6.1.4.1.89.57.6.2.1.7	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
INT rldot1sMstpInstancePortEnable	1.3.6.1.4.1.89.57.6.2.1.5	INTEGER	read-only	The enabled/disabled status of the port.
rldot1sMstpInstancePortEntry	1.3.6.1.4.1.89.57.6.2.1		not-accessible	A list of information maintained by every pair about the Spanning Tree Protocol state for that pair.
CTR rldot1sMstpInstancePortForwardTransitions	1.3.6.1.4.1.89.57.6.2.1.11	Counter	read-only	The number of times this port has transitioned from the Learning state to the Forwarding state.
INT rldot1sMstpInstancePortMstiId	1.3.6.1.4.1.89.57.6.2.1.1	INTEGER	read-only	The Vlan group number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information.
INT rldot1sMstpInstancePortPathCost	1.3.6.1.4.1.89.57.6.2.1.6	INTEGER	read-only	The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
INT rldot1sMstpInstancePortPort	1.3.6.1.4.1.89.57.6.2.1.2	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
INT rldot1sMstpInstancePortPriority	1.3.6.1.4.1.89.57.6.2.1.3	INTEGER	read-write	The value of the priority field which is contained in the more significant 4 bits of the most significant octet of the (2 octet long) Port ID. The value is a product of 16. The other octet of the Port ID is given by the value of rldot1dStpVlanGroupPort.
INT rldot1sMStpInstancePortRole	1.3.6.1.4.1.89.57.6.2.1.13	INTEGER	read-only	Specify the role of this this port.
INT rldot1sMstpInstancePortState	1.3.6.1.4.1.89.57.6.2.1.4	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpVlanPortEnable), this object will have a value of disabled(1).
rldot1sMstpInstancePortTable	1.3.6.1.4.1.89.57.6.2		not-accessible	A table that contains pair specific information for the Spanning Tree Protocol.
INT rldot1sMstpInstancePriority	1.3.6.1.4.1.89.57.6.1.1.12	INTEGER	read-write	The value of the write-able portion of the Bridge ID, i.e., the first four bits of the first octet of the (8 octet long) Bridge ID.The value is a product of 4096. The next 12 bit are the msti id . The other (last) 6 octets of the Bridge ID are given by the value of dot1dBaseBridgeAddress.
INT rldot1sMstpInstanceRemainingHopes	1.3.6.1.4.1.89.57.6.1.1.13	INTEGER	read-only	This count value determines the amount of hopes the information transmited by this bridge on this instance can travel.
INT rldot1sMstpInstanceRootCost	1.3.6.1.4.1.89.57.6.1.1.6	INTEGER	read-only	The cost of the path to the root as seen from this bridge.
INT rldot1sMstpInstanceRootPort	1.3.6.1.4.1.89.57.6.1.1.7	INTEGER	read-only	The port number of the port which offers the lowest cost path from this bridge to the root bridge.
rldot1sMstpInstanceTable	1.3.6.1.4.1.89.57.6.1		not-accessible	A table that contains Mstp instance specific information for the Multiple Spanning Tree Protocol.
TIK rldot1sMstpInstanceTimeSinceTopologyChange	1.3.6.1.4.1.89.57.6.1.1.3	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the Mstp Instance .
CTR rldot1sMstpInstanceTopChanges	1.3.6.1.4.1.89.57.6.1.1.4	Counter	read-only	The total number of topology changes detected by this Instance since the management entity was last reset or initialized.
INT rldot1sMstpMaxHopes	1.3.6.1.4.1.89.57.6.3	INTEGER	read-write	Max number of hopes that an MST BPDU will travel inside a region.
INT rldot1sMstpPendingAction	1.3.6.1.4.1.89.57.6.13	INTEGER	read-write	The action to be done with the pending configuration. copyPendingActive - to copy the pending mst configuration to the active one. copyActivePending - to copy the active mst configuration to the pending one.
STR rldot1sMstpPendingConfigurationName	1.3.6.1.4.1.89.57.6.11	SnmpAdminString	read-write	The pending configuration name.
INT rldot1sMstpPendingGroup	1.3.6.1.4.1.89.57.6.6.1.3	INTEGER	read-write	Specifid the pending group number this vlan belonges to.
INT rldot1sMstpPendingRevisionLevel	1.3.6.1.4.1.89.57.6.12	INTEGER	read-write	The pending revision level.
BRI rldot1sMstpRegionalRoot	1.3.6.1.4.1.89.57.6.9	BridgeId	read-only	CIST Regional Root Identifier (13.16.4). The Bridge Identifier of the current CIST Regional Root.
INT rldot1sMstpRegionalRootCost	1.3.6.1.4.1.89.57.6.10	INTEGER	read-only	The CIST path cost from the transmitting Bridge to the CIST Regional Root.
INT rldot1sMstpRemainingHops	1.3.6.1.4.1.89.57.6.14	INTEGER	read-only	This count value determines the amount of hops the information transmitted by this bridge can travel.
INT rldot1sMstpRevisionLevel	1.3.6.1.4.1.89.57.6.5	INTEGER	read-only	The active revision level.
INT rldot1sMstpVlan	1.3.6.1.4.1.89.57.6.6.1.1	INTEGER	read-only	The vlan number of the vlan for which this entry contains Spanning Tree Protocol management information.
rldot1sMstpVlanEntry	1.3.6.1.4.1.89.57.6.6.1		not-accessible	A list of information maintained by every vlan about the group it belongs to.
rldot1sMstpVlanTable	1.3.6.1.4.1.89.57.6.6		not-accessible	A table that contains information about the alocation of vlans to groups.
rldot1wRStp	1.3.6.1.4.1.89.57.4
T/F rldot1wRStpEdgePortStatus	1.3.6.1.4.1.89.57.4.1.1.3	TruthValue	read-write	Specifies whether this port is an Edge Port or not
rldot1wRStpForceVersionEntry	1.3.6.1.4.1.89.57.4.2.1		not-accessible	A list of information maintained by every about the RAPID Spanning Tree Protocol state for that pair.
INT rldot1wRStpForceVersionState	1.3.6.1.4.1.89.57.4.2.1.2	INTEGER	read-write	Specifies whether this Bridge uses the normal RSTP algorithm, or STP Compatibility algorythm: 0 - STP Compatibility 2 - Normal RSTP
rldot1wRStpForceVersionTable	1.3.6.1.4.1.89.57.4.2		not-accessible	A table that contains specific information for the Rapid Spanning Tree Protocol.
INT rldot1wRStpForceVersionVlan	1.3.6.1.4.1.89.57.4.2.1.1	INTEGER	read-only	The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information, If STP per device then only one value of 1 is allowed. If STP per a VLAN then all value of 1..4095 are allowed.
rldot1wRStpVlanEdgePortEntry	1.3.6.1.4.1.89.57.4.1.1		not-accessible	A list of information maintained by every pair about the RAPID Spanning Tree Protocol state for that pair.
INT rldot1wRStpVlanEdgePortPort	1.3.6.1.4.1.89.57.4.1.1.2	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
rldot1wRStpVlanEdgePortTable	1.3.6.1.4.1.89.57.4.1		not-accessible	A table that contains pair specific information for the Rapid Spanning Tree Protocol.
INT rldot1wRStpVlanEdgePortVlan	1.3.6.1.4.1.89.57.4.1.1.1	INTEGER	read-only	The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information, If STP per device then only one value of 1 is allowed. If STP per a VLAN then all value of 1..4095 are allowed.
rldot1x	1.3.6.1.4.1.89.95
rldot1xAuthenticationPortEntry	1.3.6.1.4.1.89.95.10.1		not-accessible	The Port number and mac method
INT rldot1xAuthenticationPortMethod	1.3.6.1.4.1.89.95.10.1.1	INTEGER	read-write	The value of the mac based authenication.
rldot1xAuthenticationPortTable	1.3.6.1.4.1.89.95.10		not-accessible	A table of system level information for each port supported by the Port Access Entity. An entry appears in this table for each port of this system.
C32 rldot1xAuthMultiAuthEapStartsWhileAuthenticated	1.3.6.1.4.1.89.95.12.1.10	Counter32	read-only	Counts the number of times that the state machine transitions from AUTHENTICATED to CONNECTING, as a result of an EAPOL-Start message being received from the Supplicant.
C32 rldot1xAuthMultiAuthEapStartsWhileAuthenticating	1.3.6.1.4.1.89.95.12.1.8	Counter32	read-only	Counts the number of times that the state machine transitions from AUTHENTICATING to ABORTING, as a result of an EAPOL-Start message being received from the Supplicant.
C32 rldot1xAuthMultiAuthFailWhileAuthenticating	1.3.6.1.4.1.89.95.12.1.6	Counter32	read-only	Counts the number of times that the state machine transitions from AUTHENTICATING to HELD, as a result of the Backend Authentication state machine indicating authentication failure (authFail = TRUE).
C32 rldot1xAuthMultiAuthReauthsWhileAuthenticated	1.3.6.1.4.1.89.95.12.1.9	Counter32	read-only	Counts the number of times that the state machine transitions from AUTHENTICATED to CONNECTING, as a result of a reauthentication request (reAuthenticate = TRUE).
C32 rldot1xAuthMultiAuthReauthsWhileAuthenticating	1.3.6.1.4.1.89.95.12.1.7	Counter32	read-only	Counts the number of times that the state machine transitions from AUTHENTICATING to ABORTING, as a result of a reauthentication request (reAuthenticate = TRUE).
C32 rldot1xAuthMultiAuthSuccessWhileAuthenticating	1.3.6.1.4.1.89.95.12.1.5	Counter32	read-only	Counts the number of times that the state machine transitions from AUTHENTICATING to AUTHENTICATED, as a result of the Backend Authentication state machine indicating successful authentication of the Supplicant (authSuccess = TRUE).
C32 rldot1xAuthMultiBackendAccessChallenges	1.3.6.1.4.1.89.95.12.1.12	Counter32	read-only	Counts the number of times that the state machine receives an initial Access-Challenge packet from the Authentication server (i.e., aReq becomes TRUE, causing exit from the RESPONSE state). Indicates that the Authentication Server has communication with the Authenticator.
INT rldot1xAuthMultiBackendAuthState	1.3.6.1.4.1.89.95.14.1.4	INTEGER	read-only	The current state of the Backend Authentication state machine.
C32 rldot1xAuthMultiBackendAuthSuccesses	1.3.6.1.4.1.89.95.12.1.15	Counter32	read-only	Counts the number of times that the state machine receives an EAP-Success message from the Authentication Server (i.e., aSuccess becomes TRUE, causing a transition from RESPONSE to SUCCESS). Indicates that the Supplicant has successfully authenticated to the Authentication Server.
C32 rldot1xAuthMultiBackendNonNakResponsesFromSupplicant	1.3.6.1.4.1.89.95.12.1.14	Counter32	read-only	Counts the number of times that the state machine receives a response from the Supplicant to an initial EAP-Request, and the response is something other than EAP-NAK (i.e., rxResp becomes TRUE, causing the state machine to transition from REQUEST to RESPONSE, and the response is not an EAP-NAK). Indicates that the Supplicant can respond to the Authenticators chosen EAP-method.
C32 rldot1xAuthMultiBackendOtherRequestsToSupplicant	1.3.6.1.4.1.89.95.12.1.13	Counter32	read-only	Counts the number of times that the state machine sends an EAP-Request packet (other than an Identity, Notification, Failure or Success message) to the Supplicant (i.e., executes txReq on entry to the REQUEST state). Indicates that the Authenticator chose an EAP-method.
C32 rldot1xAuthMultiBackendResponses	1.3.6.1.4.1.89.95.12.1.11	Counter32	read-only	Counts the number of times that the state machine sends an initial Access-Request packet to the Authentication server (i.e., executes sendRespToServer on entry to the RESPONSE state). Indicates that the Authenticator attempted communication with the Authentication Server.
rldot1xAuthMultiConfigEntry	1.3.6.1.4.1.89.95.14.1		not-accessible	The configuration information for an Authenticator PAE.
rldot1xAuthMultiConfigTable	1.3.6.1.4.1.89.95.14		not-accessible	A table that contains the configuration objects for the Authenticator PAE associated with each port and MAC. An entry appears in this table for each port and MAC that may authenticate access to itself.
PAE rldot1xAuthMultiControlledPortStatus	1.3.6.1.4.1.89.95.14.1.5	PaeControlledPortStatus	read-only	The current value of the controlled Port status parameter for the Port.
rldot1xAuthMultiDiagEntry	1.3.6.1.4.1.89.95.12.1		not-accessible	The diagnostics information for an Authenticator PAE.
INT rldot1xAuthMultiDiagPortNumber	1.3.6.1.4.1.89.95.12.1.1	INTEGER	read-only	Port Number.
MAC rldot1xAuthMultiDiagSourceMac	1.3.6.1.4.1.89.95.12.1.2	MacAddress	read-only	Mac of the authentication session.
rldot1xAuthMultiDiagTable	1.3.6.1.4.1.89.95.12		not-accessible	A table that contains the diagnostics objects for the Authenticator PAE associated with each Port and MAC. An entry appears in this table for each port and MAC that have an authentication session currently running under way for them.
C32 rldot1xAuthMultiEapLengthErrorFramesRx	1.3.6.1.4.1.89.95.11.1.12	Counter32	read-only	The number of EAPOL frames that have been received by this Authenticator in which the Packet Body Length field is invalid.
C32 rldot1xAuthMultiEapolFramesRx	1.3.6.1.4.1.89.95.11.1.3	Counter32	read-only	The number of valid EAPOL frames of any type that have been received by this Authenticator.
C32 rldot1xAuthMultiEapolFramesTx	1.3.6.1.4.1.89.95.11.1.4	Counter32	read-only	The number of EAPOL frames of any type that have been transmitted by this Authenticator.
C32 rldot1xAuthMultiEapolLogoffFramesRx	1.3.6.1.4.1.89.95.11.1.6	Counter32	read-only	The number of EAPOL Logoff frames that have been received by this Authenticator.
C32 rldot1xAuthMultiEapolReqFramesTx	1.3.6.1.4.1.89.95.11.1.10	Counter32	read-only	The number of EAP Request frames (other than Rq/Id frames) that have been transmitted by this Authenticator.
C32 rldot1xAuthMultiEapolReqIdFramesTx	1.3.6.1.4.1.89.95.11.1.9	Counter32	read-only	The number of EAP Req/Id frames that have been transmitted by this Authenticator.
C32 rldot1xAuthMultiEapolRespFramesRx	1.3.6.1.4.1.89.95.11.1.8	Counter32	read-only	The number of valid EAP Response frames (other than Resp/Id frames) that have been received by this Authenticator.
C32 rldot1xAuthMultiEapolRespIdFramesRx	1.3.6.1.4.1.89.95.11.1.7	Counter32	read-only	The number of EAP Resp/Id frames that have been received by this Authenticator.
C32 rldot1xAuthMultiEapolStartFramesRx	1.3.6.1.4.1.89.95.11.1.5	Counter32	read-only	The number of EAPOL Start frames that have been received by this Authenticator.
C32 rldot1xAuthMultiEntersAuthenticating	1.3.6.1.4.1.89.95.12.1.4	Counter32	read-only	Counts the number of times that the state machine transitions from CONNECTING to AUTHENTICATING, as a result of an EAP-Response/Identity message being received from the Supplicant.
C32 rldot1xAuthMultiEntersConnecting	1.3.6.1.4.1.89.95.12.1.3	Counter32	read-only	Counts the number of times that the state machine transitions to the CONNECTING state from any other state.
C32 rldot1xAuthMultiInvalidEapolFramesRx	1.3.6.1.4.1.89.95.11.1.11	Counter32	read-only	The number of EAPOL frames that have been received by this Authenticator in which the frame type is not recognized.
INT rldot1xAuthMultiPaeState	1.3.6.1.4.1.89.95.14.1.3	INTEGER	read-only	The current value of the Authenticator PAE state machine.
INT rldot1xAuthMultiPortNumber	1.3.6.1.4.1.89.95.14.1.1	INTEGER	read-only	Port Number.
C32 rldot1xAuthMultiSessionFramesRx	1.3.6.1.4.1.89.95.13.1.5	Counter32	read-only	The number of user data frames received on this Port during the session.
C32 rldot1xAuthMultiSessionFramesTx	1.3.6.1.4.1.89.95.13.1.6	Counter32	read-only	The number of user data frames transmitted on this Port during the session.
STR rldot1xAuthMultiSessionId	1.3.6.1.4.1.89.95.13.1.7	SnmpAdminString	read-only	A unique identifier for the session, in the form of a printable ASCII string of at least three characters.
C64 rldot1xAuthMultiSessionOctetsRx	1.3.6.1.4.1.89.95.13.1.3	Counter64	read-only	The number of octets received in user data frames on this Port during the session.
C64 rldot1xAuthMultiSessionOctetsTx	1.3.6.1.4.1.89.95.13.1.4	Counter64	read-only	The number of octets transmitted in user data frames on this Port during the session.
rldot1xAuthMultiSessionStatsEntry	1.3.6.1.4.1.89.95.13.1		not-accessible	The session statistics information for an Authenticator PAE. This shows the mandatory values being collected for each session that is still in progress, or the final values for the last valid session on each port where there is no session currently active.
INT rldot1xAuthMultiSessionStatsPortNumber	1.3.6.1.4.1.89.95.13.1.1	INTEGER	read-only	Port Number.
MAC rldot1xAuthMultiSessionStatsSourceMac	1.3.6.1.4.1.89.95.13.1.2	MacAddress	read-only	Mac of the authentication session.
rldot1xAuthMultiSessionStatsTable	1.3.6.1.4.1.89.95.13		not-accessible	A table that contains the session statistics objects for the Authenticator PAE associated with each Port. An entry appears in this table for each port that may authenticate access to itself.
TIK rldot1xAuthMultiSessionTime	1.3.6.1.4.1.89.95.13.1.8	TimeTicks	read-only	The duration of the session in seconds.
STR rldot1xAuthMultiSessionUserName	1.3.6.1.4.1.89.95.13.1.9	SnmpAdminString	read-only	The User-Name representing the identity of the Supplicant PAE.
MAC rldot1xAuthMultiSourceMac	1.3.6.1.4.1.89.95.14.1.2	MacAddress	read-only	Mac of the authentication session.
rldot1xAuthMultiStatsEntry	1.3.6.1.4.1.89.95.11.1		not-accessible	The statistics information for an Authenticator PAE.
INT rldot1xAuthMultiStatsPortNumber	1.3.6.1.4.1.89.95.11.1.1	INTEGER	read-only	Port Number.
MAC rldot1xAuthMultiStatsSourceMac	1.3.6.1.4.1.89.95.11.1.2	MacAddress	read-only	Mac of the authentication session.
rldot1xAuthMultiStatsTable	1.3.6.1.4.1.89.95.11		not-accessible	A table that contains the statistics objects for the Authenticator PAE associated with each Port and MAC for multisession 802.1x mode of operation. An entry appears in this table for each port and MAC that have an authentication session currently running under way for them.
INT rlDot1xAuthSessionAuthenticMethod	1.3.6.1.4.1.89.95.2.1.1	INTEGER	read-only	The authentication method used to establish the session.
T/F rldot1xBpduFilteringEnabled	1.3.6.1.4.1.89.95.15	TruthValue	read-write	Specify that when 802.1x is globally disabled, 802.1x BPDU packets would be filtered or bridged.
rldot1xExtAuthSessionStatsEntry	1.3.6.1.4.1.89.95.2.1		not-accessible	The session statistics information for an Authenticator PAE. This shows the current values being collected for each session that is still in progress, or the final values for the last valid session on each port where there is no session currently active.
rldot1xExtAuthSessionStatsTable	1.3.6.1.4.1.89.95.2		not-accessible	A table that contains the session statistics objects for the Authenticator PAE associated with each Port. An entry appears in this table for each port that may authenticate access to itself.
POR rldot1xGuestVlanPorts	1.3.6.1.4.1.89.95.5	PortList	read-write	the ports that can be members in the guest vlan
T/F rldot1xGuestVlanSupported	1.3.6.1.4.1.89.95.3	TruthValue	read-only	indicate if guest vlan is supported.
VLA rldot1xGuestVlanVID	1.3.6.1.4.1.89.95.4	VlanIndex	read-write	specify the guest vlan tag , 0 for non exiting.
INT rldot1xMibVersion	1.3.6.1.4.1.89.95.1	INTEGER	read-only	MIB's version, the current version is 1.
NTF rldot1xPortStatusAuthorizedTrap	1.3.6.1.4.1.89.0.184			Informational trap indicating that port 802.1x status is authorized.
NTF rldot1xPortStatusUnauthorizedTrap	1.3.6.1.4.1.89.0.185			Warning trap is indicating that port 802.1x status is unAuthorized.
NTF rldot1xSupplicantMacAuthorizedTrap	1.3.6.1.4.1.89.0.203			Informational trap indicating that MAC authentication supplicant is authenticated and is allowed to access the network.
NTF rldot1xSupplicantMacUnauthorizedTrap	1.3.6.1.4.1.89.0.204			Warning trap is indicating that Radius server rejects MAC authentication supplicant.
rldot1xUnAuthenticatedVlanEntry	1.3.6.1.4.1.89.95.7.1		not-accessible	port belong to vlan in all port authenticated state except force unauthenticated entry
ROW rldot1xUnAuthenticatedVlanStatus	1.3.6.1.4.1.89.95.7.1.1	RowStatus	read-write	The row status variable, used according to row installation and removal conventions.
T/F rldot1xUnAuthenticatedVlanSupported	1.3.6.1.4.1.89.95.6	TruthValue	read-only	indicate if unauthenticated Vlan is supported.
rldot1xUnAuthenticatedVlanTable	1.3.6.1.4.1.89.95.7		not-accessible	port belong to vlan in all port authenticated state except force unauthenticated table
POR rldot1xUserBasedVlanPorts	1.3.6.1.4.1.89.95.9	PortList	read-write	the ports that can be members in the user based vlan
T/F rldot1xUserBasedVlanSupported	1.3.6.1.4.1.89.95.8	TruthValue	read-only	indicate if user based Vlan is supported.
rlDot3adAgg	1.3.6.1.4.1.89.65
rlEmbWeb	1.3.6.1.4.1.89.66
rlEnv	1.3.6.1.4.1.89.83
NTF rlEnvMonFanStateChange	1.3.6.1.4.1.89.0.176			Trap indicating the fan state. rndErrorSeverity will be: 0 for fan state nomal, notPresent 1 for fan state warning, notFunctioning 2 for fan state critical 3 for fan state fatal The error text will specify the fan index, fan description and the exact fan state
NTF rlEnvMonPowerSupplyStateChange	1.3.6.1.4.1.89.0.177			Trap indicating the power supply state. rndErrorSeverity will be: 0 for power supply state nomal, notPresent 1 for power supply state warning, notFunctioning 2 for power supply state critical 3 for power supply state fatal The error text will specify the power supply index, power supply description and the exact power supply state
NTF rlEnvMonTemperatureRisingAlarm	1.3.6.1.4.1.89.0.179			Trap indicating that the temperature in the device has exceeded the device specific safe temperature threshold.
rlExperience	1.3.6.1.4.1.89.51
rlFFT	1.3.6.1.4.1.89.47
rlFile	1.3.6.1.4.1.89.96
rlGalileo	1.3.6.1.4.1.89.56
rlGlobalIpAddrTable	1.3.6.1.4.1.89.118
rlGmrp	1.3.6.1.4.1.89.75
INT rlGmrpMibVersion	1.3.6.1.4.1.89.75.2	INTEGER	read-only	MIB's version, the current version is 1.
T/F rlGmrpSupported	1.3.6.1.4.1.89.75.1	TruthValue	read-only	Is Gmrp supported in the device or not.
T/F rlGmrpVlanEnable	1.3.6.1.4.1.89.75.4.1.2	TruthValue	read-write	Enable/Disable Gmrp in the vlan.
rlGmrpVlanEntry	1.3.6.1.4.1.89.75.4.1		not-accessible	An entry in the rlGmrpVlanTable.
rlGmrpVlanTable	1.3.6.1.4.1.89.75.4		not-accessible	This table is to Enable/Disable Gmrp in the vlan.
INT rlGmrpVlanTag	1.3.6.1.4.1.89.75.4.1.1	INTEGER	read-only	The tag of the VLAN for which this entry contains information.
rlGvrp	1.3.6.1.4.1.89.64
INT rlGvrpMibVersion	1.3.6.1.4.1.89.64.3	INTEGER	read-only	MIB's version, the current version is 3.
T/F rlGvrpSupported	1.3.6.1.4.1.89.64.2	TruthValue	read-only	Is GVRP supported in this device or not
NTF rlHotSwapTrap	1.3.6.1.4.1.89.0.159			Hot swap trap.
rlIfInterfaces	1.3.6.1.4.1.89.54
NTF rlIgmpProxyTableOverflow	1.3.6.1.4.1.89.0.156			An IGMP PROXY Table overflow.
NTF rlIgmpV1MsgReceived	1.3.6.1.4.1.89.0.157			An IGMP Message of v1 received on ifIndex.
rlIntel	1.3.6.1.4.1.89.121
NTF rlIpFftStnOverflow	1.3.6.1.4.1.89.0.145			The IP SFFT overflow.
NTF rlIpFftSubOverflow	1.3.6.1.4.1.89.0.146			The IP NFFT overflow.
NTF rlIpmFftOverflow	1.3.6.1.4.1.89.0.149			The IPM FFT overflow.
rlIpMRouteStdMIB	1.3.6.1.4.1.89.62
rlIPmulticast	1.3.6.1.4.1.89.46
NTF rlIpxFftStnOverflow	1.3.6.1.4.1.89.0.147			The IPX SFFT overflow.
NTF rlIpxFftSubOverflow	1.3.6.1.4.1.89.0.148			The IPX NFFT overflow.
rlJumboFrames	1.3.6.1.4.1.89.91
INT rlJumboFramesCurrentStatus	1.3.6.1.4.1.89.91.1	INTEGER	read-only	Show the current Jumbo Frames status
INT rlJumboFramesStatusAfterReset	1.3.6.1.4.1.89.91.2	INTEGER	read-write	Set the Jumbo Frames status after reset
rlLinksysSmartMIB	1.3.6.1.4.1.89.115
rlLldp	1.3.6.1.4.1.89.110
rlLocalization	1.3.6.1.4.1.89.103
NTF rlLockPortTrap	1.3.6.1.4.1.89.0.170			Informational trap indicating that a locked port receive a frame with new source Mac Address.
rlMacBasePrio	1.3.6.1.4.1.89.101
rlMacMulticast	1.3.6.1.4.1.89.55
INT rlManagedMrid	1.3.6.1.4.1.89.2.7.3.1.2	INTEGER	read-write	The router instance currently managed by the NMS who accessed the agent through the community table entry corresponding to the keys of this entry
T/F rlManualReboot	1.3.6.1.4.1.89.94.2	TruthValue	read-only	Indicates whether the device was shutdown orderly before reboot or not (i.e. power failure)
STR rlMD5Key	1.3.6.1.4.1.89.86.2.1.2	DisplayString	read-write	The 128-bit secret authentication key. The key can get value only once and cannot be modified. When read, rlMD5KeyChainKey always returns an Octet String of length zero.
rlMD5KeyChainEntry	1.3.6.1.4.1.89.86.1.1		not-accessible	Key-chain with key ID that belongs to this chain
INT rlMD5KeyChainKeyId	1.3.6.1.4.1.89.86.1.1.2	INTEGER	read-only	A 8-bit identifier for the secret authentication key. This identifier is the same as key ID used in rlMD5KeyTable.
ROW rlMD5KeyChainKeyRowStatus	1.3.6.1.4.1.89.86.1.1.3	RowStatus	read-write	It is used to insert, update or delete an entry
STR rlMD5KeyChainName	1.3.6.1.4.1.89.86.1.1.1	DisplayString	read-only	Name of the key-chain to which belongs the secret authentication key
rlMD5KeyChainTable	1.3.6.1.4.1.89.86.1		not-accessible	Key-chains and key ID's
rlMD5KeyEntry	1.3.6.1.4.1.89.86.2.1		not-accessible	Secret authentication key with all related parameters
INT rlMD5KeyId	1.3.6.1.4.1.89.86.2.1.1	INTEGER	read-only	A 8-bit identifier for the secret authentication key
ROW rlMD5KeyRowStatus	1.3.6.1.4.1.89.86.2.1.7	RowStatus	read-write	It is used to insert, update or delete an entry
DAT rlMD5KeyStartAccept	1.3.6.1.4.1.89.86.2.1.3	DateAndTime	read-write	The time that the router will start accepting packets that have been created with the given key
DAT rlMD5KeyStartGenerate	1.3.6.1.4.1.89.86.2.1.4	DateAndTime	read-write	The time that the router will start using the key for packet generation
DAT rlMD5KeyStopAccept	1.3.6.1.4.1.89.86.2.1.6	DateAndTime	read-write	The time that the router will stop accepting packets that have been created with the given key
DAT rlMD5KeyStopGenerate	1.3.6.1.4.1.89.86.2.1.5	DateAndTime	read-write	The time that the router will stop using the key for packet generation
rlMD5KeyTable	1.3.6.1.4.1.89.86.2		not-accessible	Secret authentication keys used by MD5 Authentication Algorithm
rlMir	1.3.6.1.4.1.89.61
INT rlMirCurMriNum	1.3.6.1.4.1.89.61.4	INTEGER	read-write	The number of the MRI of which MIB variables are treated at the same time by the SNMP agent.
rlMirInterfaceEntry	1.3.6.1.4.1.89.61.5.1		not-accessible	An entry of this table specifies the MRID assignement to a L2 interfrace.
NUM rlMirInterfaceIfIndex	1.3.6.1.4.1.89.61.5.1.1	InterfaceIndex	read-write	The L2 interface for which this entry contains information.
INT rlMirInterfaceMrid	1.3.6.1.4.1.89.61.5.1.2	INTEGER	read-write	Multi IP Router Instance Identifier to which the interface is assgned.
rlMirInterfaceTable	1.3.6.1.4.1.89.61.5		not-accessible	A list of the assignment ifinterfaces to IP Router instances.
INT rlMirMaxNumOfMRIs	1.3.6.1.4.1.89.61.3	INTEGER	read-only	The maximun instanses of IP Multi Instance Routers.
INT rlMirMaxNumOfMRIsAfterReset	1.3.6.1.4.1.89.61.2	INTEGER	read-write	The maximun instanses of IP Multi Instance Routers after the following reset.
INT rlMirMibVersion	1.3.6.1.4.1.89.61.1	INTEGER	read-only	MIB's version, the current version is 1.
rlMirVlanBaseLogicalPortsEntry	1.3.6.1.4.1.89.61.7.1		not-accessible	A VLAN based logical point-to-point port.
NUM rlMirVlanBaseLogicalPortsIfIndex	1.3.6.1.4.1.89.61.7.1.1	InterfaceIndex	read-write	IfIndex of VLAN based Logical point-to-point port.
NUM rlMirVlanBaseLogicalPortsReservedIfIndex	1.3.6.1.4.1.89.61.7.1.2	InterfaceIndex	read-write	IfIndex of VLAN based reserved physical port on which the logical port is defined.
ROW rlMirVlanBaseLogicalPortsStatus	1.3.6.1.4.1.89.61.7.1.4	RowStatus	read-write	It is used to add, update and delete an entry
rlMirVlanBaseLogicalPortsTable	1.3.6.1.4.1.89.61.7		not-accessible	A list VLAN based logical ports.
INT rlMirVlanBaseLogicalPortsVlanTag	1.3.6.1.4.1.89.61.7.1.3	INTEGER	read-write	VLAN tag.
rlMirVlanBaseReservedPortsEntry	1.3.6.1.4.1.89.61.6.1		not-accessible	A VLAN based reserved physical port.
NUM rlMirVlanBaseReservedPortsIfIndex	1.3.6.1.4.1.89.61.6.1.1	InterfaceIndex	read-write	IfIndex of VLAN based reserved physical port.
ROW rlMirVlanBaseReservedPortsStatus	1.3.6.1.4.1.89.61.6.1.2	RowStatus	read-write	It is used to delete an entry
rlMirVlanBaseReservedPortsTable	1.3.6.1.4.1.89.61.6		not-accessible	A list VLAN based reserved physical ports.
rlMngInf	1.3.6.1.4.1.89.89
INT rlMridConnection	1.3.6.1.4.1.89.2.7.3.1.1	INTEGER	read-write	The router instance connecting the NMS who accessed the agent through the community table entry corresponding to the keys of this entry.
rlMridEntry	1.3.6.1.4.1.89.2.7.3.1		not-accessible	The row definition for this table.
rlMridTable	1.3.6.1.4.1.89.2.7.3		not-accessible	The MRID related configurations table of the agent
rlMultiSessionTerminal	1.3.6.1.4.1.89.69
rlNicRedundancy	1.3.6.1.4.1.89.105
rlOib	1.3.6.1.4.1.89.111
rlpBridgeMIBObjects	1.3.6.1.4.1.89.57
rlPhy	1.3.6.1.4.1.89.90
rlPhysicalDescription	1.3.6.1.4.1.89.53
NTF rlPhysicalDescriptionChanged	1.3.6.1.4.1.89.0.150			Indicates that the physical decription of the device has changed
rlPoe	1.3.6.1.4.1.89.108
rlPolicy	1.3.6.1.4.1.89.59
NTF rlPolicyDropPacketTrap	1.3.6.1.4.1.89.0.153			Indicates that the packet drop due to the policy
NTF rlPolicyForwardPacketTrap	1.3.6.1.4.1.89.0.154			Indicates that the packet has forward based on policy
INT rlPortCopyMibVersion	1.3.6.1.4.1.89.84.1	INTEGER	read-only	MIB's version, the current version is 1.
INT rlPortCopySupport	1.3.6.1.4.1.89.84.2	INTEGER	read-only	supported - The standard portCopy is supported. notSupported - the standard portCopy is not supported. only basic portCopy operation is supported.
T/F rlPortCopyVlanTagging	1.3.6.1.4.1.89.84.3.1.1	TruthValue	read-write	TRUE - Mirrored packets will transmit from portCopyDest - Tagged FALSE - Mirrored packets will transmit from portCopyDest - unTagged
rlPortCopyVlanTaggingEntry	1.3.6.1.4.1.89.84.3.1		not-accessible	Each entry specify how mirrored packets will transmit from the portCopyDest: Tagged or unTagged. The values in this entry will be valid only when the dot1dBasePort will be configured as a portCopyDest in the portCopyTable.
rlPortCopyVlanTaggingTable	1.3.6.1.4.1.89.84.3		not-accessible	A supplementing table for portCopyTable. For every portCopyDest a vlan-tagging option is available.
NUM rlPortGmrpJoinTime	1.3.6.1.4.1.89.75.3.1.1	TimeInterval	read-write	The Gmrp Join time, in centiseconds.
NUM rlPortGmrpLeaveAllTime	1.3.6.1.4.1.89.75.3.1.3	TimeInterval	read-write	The Gmrp LeaveAll time, in centiseconds.
NUM rlPortGmrpLeaveTime	1.3.6.1.4.1.89.75.3.1.2	TimeInterval	read-write	The Gmrp Leave time, in centiseconds.
ENA rlPortGmrpOverrideGarp	1.3.6.1.4.1.89.75.3.1.4	EnabledStatus	read-write	If enabled{1}, Gmrp timer values for this port are determined by the values in this entry. Otherwise, they are determined by the values in dot1dPortGarpTable.
rlPortGmrpTimersEntry	1.3.6.1.4.1.89.75.3.1		not-accessible	Gmrp timer values for a bridge port.
rlPortGmrpTimersTable	1.3.6.1.4.1.89.75.3		not-accessible	A table of Gmrp timer values for every bridge port. This is indexed by dot1dBasePort.
rlPortGvrpApplicantStatusEntry	1.3.6.1.4.1.89.64.6.1		not-accessible	GVRP Applicant Status value for a bridge port.
rlPortGvrpApplicantStatusTable	1.3.6.1.4.1.89.64.6		not-accessible	A table of GVRP Applicant Status values for every bridge port. This is indexed by dot1dBasePort.
INT rlPortGvrpApplicantStatusValue	1.3.6.1.4.1.89.64.6.1.1	INTEGER	read-write	participant - the Gvrp enabled port sending GARP PDUs. nonParticipant - preventing the Gvrp enabled port from sending GARP PDUs.
INT rlPortGvrpErrorStatisticsClear	1.3.6.1.4.1.89.64.5.1.7	INTEGER	read-write	activate - the signal/trigger to clear ALL the rlPortGvrpErrorStatisticsEntry's fields. passive - specify that the rlPortGvrpErrorStatisticsClear field is not activate, or finshed the clearnce process. the rlPortGvrpErrorStatisticsClear return automatically to passive after it was activate.
rlPortGvrpErrorStatisticsEntry	1.3.6.1.4.1.89.64.5.1		not-accessible	GVRP ErrorStatistics values for a bridge port.
CTR rlPortGvrpErrorStatisticsInvAlen	1.3.6.1.4.1.89.64.5.1.5	Counter	read-only	The number of Invalid Attribute Length encountered by the GVRP port. (since the last clearance)
CTR rlPortGvrpErrorStatisticsInvAtyp	1.3.6.1.4.1.89.64.5.1.2	Counter	read-only	The number of Invalid Attribute Type encountered by the GVRP port. (since the last clearance)
CTR rlPortGvrpErrorStatisticsInvAval	1.3.6.1.4.1.89.64.5.1.3	Counter	read-only	The number of Invalid Attribute Value encountered by the GVRP port. (since the last clearance)
CTR rlPortGvrpErrorStatisticsInvEvent	1.3.6.1.4.1.89.64.5.1.6	Counter	read-only	The number of Invalid Event encountered by the GVRP port. (since the last clearance)
CTR rlPortGvrpErrorStatisticsInvPlen	1.3.6.1.4.1.89.64.5.1.4	Counter	read-only	The number of Invalid PDU Length encountered by the GVRP port. (since the last clearance)
CTR rlPortGvrpErrorStatisticsInvProt	1.3.6.1.4.1.89.64.5.1.1	Counter	read-only	The number of Invalid Protocol Id encountered by the GVRP port. (since the last clearance)
rlPortGvrpErrorStatisticsTable	1.3.6.1.4.1.89.64.5		not-accessible	A table of GVRP ErrorStatistics values for every bridge port. This is indexed by dot1dBasePort.
NUM rlPortGvrpJoinTime	1.3.6.1.4.1.89.64.1.1.1	TimeInterval	read-write	The GVRP Join time, in centiseconds.
NUM rlPortGvrpLeaveAllTime	1.3.6.1.4.1.89.64.1.1.3	TimeInterval	read-write	The GVRP LeaveAll time, in centiseconds.
NUM rlPortGvrpLeaveTime	1.3.6.1.4.1.89.64.1.1.2	TimeInterval	read-write	The GVRP Leave time, in centiseconds.
ENA rlPortGvrpOverrideGarp	1.3.6.1.4.1.89.64.1.1.4	EnabledStatus	read-write	If enabled{1}, GVRP timer values for this port are determined by the values in this entry. Otherwise, they are determined by the values in dot1dPortGarpTable.
rlPortGvrpRegistrationModeEntry	1.3.6.1.4.1.89.64.8.1		not-accessible	GVRP Registration Mode value for a bridge port.
T/F rlPortGvrpRegistrationModeForbidden	1.3.6.1.4.1.89.64.8.1.1	TruthValue	read-write	true - deregisters all VLANS on the specified port and prevents any VLAN creation or registration on that port. false - the registration operation on this port behaves normally.
rlPortGvrpRegistrationModeTable	1.3.6.1.4.1.89.64.8		not-accessible	A table of GVRP Registration Mode values for every bridge port. This is indexed by dot1dBasePort.
INT rlPortGvrpStatisticsClear	1.3.6.1.4.1.89.64.4.1.13	INTEGER	read-write	activate - the signal/trigger to clear ALL the rlPortGvrpStatisticsEntry's fields. passive - specify that the rlPortGvrpStatisticsClear field is not activate, or finshed the clearnce process. the rlPortGvrpStatisticsClear return automatically to passive after it was activate.
rlPortGvrpStatisticsEntry	1.3.6.1.4.1.89.64.4.1		not-accessible	GVRP statistics values for a bridge port.
CTR rlPortGvrpStatisticsREmp	1.3.6.1.4.1.89.64.4.1.3	Counter	read-only	The number of Empty Received on the port, since the last clearance.
CTR rlPortGvrpStatisticsRJE	1.3.6.1.4.1.89.64.4.1.1	Counter	read-only	The number of Join Empty Received on the port, since the last clearance.
CTR rlPortGvrpStatisticsRJIn	1.3.6.1.4.1.89.64.4.1.2	Counter	read-only	The number of Join In Received on the port, since the last clearance.
CTR rlPortGvrpStatisticsRLA	1.3.6.1.4.1.89.64.4.1.6	Counter	read-only	The number of Leave All Received on the port, since the last clearance.
CTR rlPortGvrpStatisticsRLE	1.3.6.1.4.1.89.64.4.1.5	Counter	read-only	The number of Leave Empty Received on the port, since the last clearance.
CTR rlPortGvrpStatisticsRLIn	1.3.6.1.4.1.89.64.4.1.4	Counter	read-only	The number of Leave In Received on the port, since the last clearance.
CTR rlPortGvrpStatisticsSEmp	1.3.6.1.4.1.89.64.4.1.9	Counter	read-only	The number of Empty Sent on the port, since the last clearance.
CTR rlPortGvrpStatisticsSJE	1.3.6.1.4.1.89.64.4.1.7	Counter	read-only	The number of Join Empty Sent on the port, since the last clearance.
CTR rlPortGvrpStatisticsSJIn	1.3.6.1.4.1.89.64.4.1.8	Counter	read-only	The number of Join In Sent on the port, since the last clearance.
CTR rlPortGvrpStatisticsSLA	1.3.6.1.4.1.89.64.4.1.12	Counter	read-only	The number of Leave All Sent on the port, since the last clearance.
CTR rlPortGvrpStatisticsSLE	1.3.6.1.4.1.89.64.4.1.11	Counter	read-only	The number of Leave Empty Sent on the port, since the last clearance.
CTR rlPortGvrpStatisticsSLIn	1.3.6.1.4.1.89.64.4.1.10	Counter	read-only	The number of Leave In Sent on the port, since the last clearance.
rlPortGvrpStatisticsTable	1.3.6.1.4.1.89.64.4		not-accessible	A table of GVRP statistics values for every bridge port. This is indexed by dot1dBasePort.
rlPortGvrpTimersEntry	1.3.6.1.4.1.89.64.1.1		not-accessible	GVRP timer values for a bridge port.
rlPortGvrpTimersTable	1.3.6.1.4.1.89.64.1		not-accessible	A table of GVRP timer values for every bridge port. This is indexed by dot1dBasePort.
rlQosCliMib	1.3.6.1.4.1.89.88
rlRadius	1.3.6.1.4.1.89.80
rlRCli	1.3.6.1.4.1.89.70
OCT rlRCliConfigPassword	1.3.6.1.4.1.89.70.4	OCTET STRING	read-write	RCLI Config mode Password
OCT rlRCliEnablePassword	1.3.6.1.4.1.89.70.3	OCTET STRING	read-write	RCLI Enable mode Password
INT rlRcliFileAction	1.3.6.1.4.1.89.70.6	INTEGER	read-write	RCLI Configuration File action determines whether The device configuration after reset will be set by the configuration file content or not.
INT rlRCliMibVersion	1.3.6.1.4.1.89.70.1	INTEGER	read-only	MIB's version, the current version is 1.
INT rlRCliTimer	1.3.6.1.4.1.89.70.5	INTEGER	read-write	RCLI Timeout
OCT rlRCliUserPassword	1.3.6.1.4.1.89.70.2	OCTET STRING	read-write	RCLI User mode Password
rlRmonControl	1.3.6.1.4.1.89.49
rlRs232	1.3.6.1.4.1.89.104
rlSecuritySuiteMib	1.3.6.1.4.1.89.120
rlSmon	1.3.6.1.4.1.89.84
rlSNMP	1.3.6.1.4.1.89.98
rlSocket	1.3.6.1.4.1.89.85
INT rlSocketBlockMode	1.3.6.1.4.1.89.85.2.1.4	INTEGER	read-only	Specifies the blocking mode of the socket.
rlSocketEntry	1.3.6.1.4.1.89.85.2.1		not-accessible	An entry (conceptual row) in the SocketTable.
INT rlSocketId	1.3.6.1.4.1.89.85.2.1.1	INTEGER	read-only	The value of the id of the socket.
INT rlSocketMibVersion	1.3.6.1.4.1.89.85.1	INTEGER	read-only	MIB's version, the current version is 1.
INT rlSocketState	1.3.6.1.4.1.89.85.2.1.3	INTEGER	read-only	Specifies the state in which the socket is in.
rlSocketTable	1.3.6.1.4.1.89.85.2		not-accessible	The (conceptual) table listing the sockets which are currently open in the system.
INT rlSocketType	1.3.6.1.4.1.89.85.2.1.2	INTEGER	read-only	Specifies the type of the socket.
TIK rlSocketUpTime	1.3.6.1.4.1.89.85.2.1.5	TimeTicks	read-only	The time elapsed since this socket was created.
rlSsh	1.3.6.1.4.1.89.78
rlSsl	1.3.6.1.4.1.89.100
rlStack	1.3.6.1.4.1.89.107
NTF rlStackStateChange	1.3.6.1.4.1.89.0.178			Trap indicating the stack connection state 0 for stack state connected, 1 for stack state disconnected
T/F rlStartupCDBChanged	1.3.6.1.4.1.89.94.1	TruthValue	read-only	Indicates whether the startup CDB has changed between the router's last two reboots
rlStormCtrl	1.3.6.1.4.1.89.77
T/F rlStormCtrlBroadcastEnable	1.3.6.1.4.1.89.77.8.1.6	TruthValue	read-write	enable or disable the storm control for Broadcast frames
U32 rlStormCtrlBroadcastRate	1.3.6.1.4.1.89.77.8.1.7	Unsigned_32	read-write	set the storm control rate limit for the Broadcast frames, 0 indicate blocking of frames from this type.
OCT rlStormCtrlEnbaleDependencyBetweenTypes	1.3.6.1.4.1.89.77.6	OCTET STRING	read-only	indicate enable limitation of dependency between frame types, such as enabling of multicast should be with the enabling of broadcast type (bcm 5632)
rlStormCtrlEntry	1.3.6.1.4.1.89.77.8.1		not-accessible	storm control protection, defined per port,frame type and rate
INT rlStormCtrlGroupBroadcastId	1.3.6.1.4.1.89.77.9.1.3	INTEGER	read-only	Indicates the id of the group for broadcast frame type that the port belongs to, 0 indicates that broadcast frame type is not supported.
rlStormCtrlGroupEntry	1.3.6.1.4.1.89.77.9.1		not-accessible	group id for each supported frame type defined per port.
INT rlStormCtrlGroupMulticastId	1.3.6.1.4.1.89.77.9.1.4	INTEGER	read-only	Indicates the id of the group for multicast frame type that the port belongs to, 0 indicates that multicast frame type is not supported.
rlStormCtrlGroupTable	1.3.6.1.4.1.89.77.9		not-accessible	The table contains per port for each supported frame type to which group it belongs.
INT rlStormCtrlGroupUnknownMulticastId	1.3.6.1.4.1.89.77.9.1.2	INTEGER	read-only	Indicates the id of the group for unknown multicast frame type that the port belongs to, 0 indicates that unknown multicast frame type is not supported.
INT rlStormCtrlGroupUnknownUnicastId	1.3.6.1.4.1.89.77.9.1.1	INTEGER	read-only	Indicates the id of the group for unknown unicast frame type that the port belongs to, 0 indicates that unknown unicast frame type is not supported.
INT rlStormCtrlMibVersion	1.3.6.1.4.1.89.77.2	INTEGER	read-only	MIB's version, the current version is 3.
T/F rlStormCtrlMulticastEnable	1.3.6.1.4.1.89.77.8.1.8	TruthValue	read-write	enable or disable the storm control for multicast frames
U32 rlStormCtrlMulticastRate	1.3.6.1.4.1.89.77.8.1.9	Unsigned_32	read-write	set the storm control rate limit for the multicast frames, 0 indicate blocking of frames from this type.
OCT rlStormCtrlRateDependencyBetweenTypes	1.3.6.1.4.1.89.77.7	OCTET STRING	read-only	indicate limitation of dependency between frame types for rate assignment, for example: assigning of rate limit for unicast frame must assigning the same rate for multicast and bradcast frame (bcm 5615), in case the device support enbale per each frame type but with the same rate limitation.
OCT rlStormCtrlRateSupportPerType	1.3.6.1.4.1.89.77.5	OCTET STRING	read-only	identify if rate control is supported for each frame type
RLS rlStormCtrlRateType	1.3.6.1.4.1.89.77.8.1.1	RlStormCtrlRateUnit	read-write	indicate the rate unit type
OCT rlStormCtrlRateUnitTypeSupport	1.3.6.1.4.1.89.77.3	OCTET STRING	read-only	the supported rate unit type for the storm rate control
T/F rlStormCtrlSetDefaultBroadcastEnable	1.3.6.1.4.1.89.77.8.1.15	TruthValue	read-write	indicate if return the storm control enable for Broadcast frames to its default.
T/F rlStormCtrlSetDefaultBroadcastRate	1.3.6.1.4.1.89.77.8.1.16	TruthValue	read-write	indicate if return the storm control rate limit for the Broadcast frames to its default.
T/F rlStormCtrlSetDefaultMulticastEnable	1.3.6.1.4.1.89.77.8.1.17	TruthValue	read-write	indicate if return the storm control for multicast frames to its default.
T/F rlStormCtrlSetDefaultMulticastRate	1.3.6.1.4.1.89.77.8.1.18	TruthValue	read-write	indicate if return the storm control rate limit for the multicast frames to its default.
T/F rlStormCtrlSetDefaultRateType	1.3.6.1.4.1.89.77.8.1.10	TruthValue	read-write	indicate if return the rate unit type to its default.
T/F rlStormCtrlSetDefaultUnknownMulticastEnable	1.3.6.1.4.1.89.77.8.1.13	TruthValue	read-write	indicate if return the storm control enable for unknown multicast frames to its default.
T/F rlStormCtrlSetDefaultUnknownMulticastRate	1.3.6.1.4.1.89.77.8.1.14	TruthValue	read-write	indicate if return the storm control rate limit for the unknown multicast frames to its default.
T/F rlStormCtrlSetDefaultUnknownUnicastEnable	1.3.6.1.4.1.89.77.8.1.11	TruthValue	read-write	indicate if return the storm control enable for unknown unicast frames to its default.
T/F rlStormCtrlSetDefaultUnknownUnicastRate	1.3.6.1.4.1.89.77.8.1.12	TruthValue	read-write	indicate if return the storm control rate limit for the unknown unicast frames to its default.
T/F rlStormCtrlSupport	1.3.6.1.4.1.89.77.1	TruthValue	read-only	Identify if the strom control protection is supported
rlStormCtrlTable	1.3.6.1.4.1.89.77.8		not-accessible	The table contains the storm control protection per port
OCT rlStormCtrlTypeSupport	1.3.6.1.4.1.89.77.4	OCTET STRING	read-only	the supported frame type for the storm control protection
T/F rlStormCtrlUnknownMulticastEnable	1.3.6.1.4.1.89.77.8.1.4	TruthValue	read-write	enable or disable the storm control for unknown multicast frames
U32 rlStormCtrlUnknownMulticastRate	1.3.6.1.4.1.89.77.8.1.5	Unsigned_32	read-write	set the storm control rate limit for the unknown multicast frames, 0 indicate blocking of frames from this type.
T/F rlStormCtrlUnknownUnicastEnable	1.3.6.1.4.1.89.77.8.1.2	TruthValue	read-write	enable or disable the storm control for unknown unicast frames
U32 rlStormCtrlUnknownUnicastRate	1.3.6.1.4.1.89.77.8.1.3	Unsigned_32	read-write	set the storm control rate limit for the unknown unicast frames, 0 indicate blocking of frames from this type.
rlSwPackageVersion	1.3.6.1.4.1.89.67
rlSwPackageVersionEntry	1.3.6.1.4.1.89.67.1.1		not-accessible	The row definition for this table.
STR rlSwPackageVersionName	1.3.6.1.4.1.89.67.1.1.1	DisplayString	read-only	The Package name.
rlSwPackageVersionTable	1.3.6.1.4.1.89.67.1		not-accessible	The table listing the current versions of packages that are included in the running software.
STR rlSwPackageVersionVesrion	1.3.6.1.4.1.89.67.1.1.2	DisplayString	read-only	The Package version.
rlSyslog	1.3.6.1.4.1.89.82
rlTelnet	1.3.6.1.4.1.89.58
STR rlTelnetLoginBanner	1.3.6.1.4.1.89.58.5	DisplayString	read-write	Telnet Login Banner. When telnet connection is established, the banner is the concatanation of this MIB and rlTelnetSecondLoginBanner.
INT rlTelnetMibVersion	1.3.6.1.4.1.89.58.1	INTEGER	read-only	MIB's version, the current version is 1.
STR rlTelnetPassword	1.3.6.1.4.1.89.58.2	DisplayString	read-write	Telnet Password
STR rlTelnetSecondLoginBanner	1.3.6.1.4.1.89.58.6	DisplayString	read-write	Telnet Login Banner Extension. When telnet connection is established, the banner is the concatanation of rlTelnetLoginBanner and this MIB
IP rlTelnetSessionClientAddress	1.3.6.1.4.1.89.58.4.1.2	IpAddress	read-only	Telnet Session Client IP address
INT rlTelnetSessionId	1.3.6.1.4.1.89.58.4.1.1	INTEGER	read-only	Telnet Session ID
STR rlTelnetSessionLoginTime	1.3.6.1.4.1.89.58.4.1.3	DisplayString	read-only	Telnet Session Login Time string
INT rlTelnetSessionStatus	1.3.6.1.4.1.89.58.4.1.4	INTEGER	read-write	Telnet Session status. After status has been set to diconnect the sessions is closed and the matching entry is deleted from the table.
INT rlTelnetTimeout	1.3.6.1.4.1.89.58.3	INTEGER	read-write	The number of minutes after which the TCP connection is closed if no activity is detected from the Client
rlTelnetUsersEntry	1.3.6.1.4.1.89.58.4.1		not-accessible	The row definition for this table.
rlTelnetUsersTable	1.3.6.1.4.1.89.58.4		not-accessible	This table hold information about current telnet sessions
STR rlTerminalDebugModePassword	1.3.6.1.4.1.89.69.1	DisplayString	read-write	When a user wants to change the terminal mode from debug mode to ASCII he must enter this password first
rlTimeSynchronization	1.3.6.1.4.1.89.92
rlTraceRoute	1.3.6.1.4.1.89.81
INT rlTraceRouteMibVersion	1.3.6.1.4.1.89.81.1	INTEGER	read-only	MIB's version, the current version is 1.
NTF rlTrunkPortAddedTrap	1.3.6.1.4.1.89.0.160			Informational trap indicating that a port is added to a trunk
NTF rlTrunkPortNotCapableTrap	1.3.6.1.4.1.89.0.162			Informational trap indicating that a port can not be added to a trunk because of device limitations or diffrent swIfType.
NTF rlTrunkPortRemovedTrap	1.3.6.1.4.1.89.0.161			This warning is generated when a port removed from a trunk.
rlUPnP	1.3.6.1.4.1.89.109
NTF rlVrrpEntriesDeleted	1.3.6.1.4.1.89.0.158			One or more VRRP entries deleted due to IP interface deletion or transition.
rlWlanAccessPoint	1.3.6.1.4.1.89.102
rlWlanMIB	1.3.6.1.4.1.89.200
rnd	1.3.6.1.4.1.89
INT rndActiveSoftwareFile	1.3.6.1.4.1.89.2.13.1.1.2	INTEGER	read-only	Indicates the current active software file, image1 or image2.
INT rndActiveSoftwareFileAfterReset	1.3.6.1.4.1.89.2.13.1.1.3	INTEGER	read-write	Indicates the software file that will be active after reset (image1 or image2). If an error occurred in the download process, resulting in the corruption of the single software file, The value 'invalidImage' will be returned. This value can not be set by the user.
rndActiveSoftwareFileEntry	1.3.6.1.4.1.89.2.13.1.1		not-accessible	An entry (conceptual row) in the rndActiveSoftwareFileTable.
rndActiveSoftwareFileTable	1.3.6.1.4.1.89.2.13.1		not-accessible	The (conceptual) table listing the active software file of the requested unit.
rndApplications	1.3.6.1.4.1.89.35
T/F rndBackupConfigurationEnabled	1.3.6.1.4.1.89.2.15	TruthValue	read-only	Specifies whether the device supports backup-config parameters in lcli commands.
STR rndBaseBootVersion	1.3.6.1.4.1.89.2.10	DisplayString	read-only	Defines the boot version of the product.
PHY rndBasePhysicalAddress	1.3.6.1.4.1.89.2.12	PhysAddress	read-only	The Base physical (MAC) address of the device.
rndBootP	1.3.6.1.4.1.89.24
INT rndBootPRelaySecThreshold	1.3.6.1.4.1.89.24.2	INTEGER	read-write	BootP requests are relayed only if their SEC field is greater or equal to the threshold value in order to allow local BootP Servers to answer first.
IP rndBootPServerAddress	1.3.6.1.4.1.89.24.1	IpAddress	read-write	The IPAddress of the BOOTP server. the OpenGate will act as a BootP relay if this parameter is not equale to 0.0.0.0.
OCT rndBrgFeatures	1.3.6.1.4.1.89.2.5	OCTET STRING	read-only	A bit mask that defines the features supported by a particular configuration of this network element: __________________________________________ \| Byte 1\|Byte 2 \|Byte 3 \| ....\|Byte 20 \| \|87654321\| \| 87654321\| \|________\|_______________________________\| Byte1 : bit1: TX Block mask bit2: Source Routing Encapulation bit3: SNA/SDLC bit4: Frame Relay bit5: SNMP bit6: LAN Manager bit7: High Performance bit8: Translation Byte2 : bit1: DEC Router bit2: IPX Router bit3: IP Router Byte3 : bit1: Dial Up Backup bit2: COD bit3: FACS bit4: Load Balance bit5: Remote Configuration bit6: RIP 2 bit7: OSPF bit8: IPX RIP/SAP Filter Byte4 : bit1: BootP Server bit2: BootP Client bit3: Compression bit4: V25.bis bit5: ISDN bit6: CODv2 bit7: NSPF bit8: UDP Relay Byte5 bit1:VirtualLAN bit2:Static IP Multicast bit3:IP Redundancy bit4:CCM2 bit5:ISDN Bonding bit6:Backup Link Selection -- for the VAN/Rdapter ver 4.0 bit7:IP/IPX Forwarding -- for the WANgate ver 4.0 bit8:Improved COD Byte6 bit1: Server Disptacher bit2: ISDN_US -- for the VANSX/WANGATE ver 5.0 bit3: PPP bit4: IP Rip Filter -- for Vgate3 bit5: Zero Hop Routing -- for Vgate3 bit6: ISDN Japan bit7: PPP-Security Byte7 bit1: With unmanaged Switch bit2: 2 LANs bit3: OSPF Ver 2.0 bit4: FACS Ver 2.0 bit5: Multiple WEB Farm bit6: Backup Server bit7: Check Connectivity bit8: WSD multiplexing Byte8 bit1: MRT3 bit2: WSD Redundancy bit3: DHCP Server bit4: WSD Connection Limit bit5: WSD Distributed System bit6: WSD Load Report bit7: WSD super farm bit8: RadWiz leased line Byte9 bit1: PPP IP address negotiaton bit2: DNS bit3: Nat bit4: WSD Static proximity bit5: WSD Dynamic proximity bit6: WSD Proxy bit7: WSD Proximity client bit8: MAC Load balancing Byte10 bit1: Unnum Inf bit2: Power Supply redundancy bit3: MRT PPP Compression bit4: ZHR Apolo bit5: Copy port bit6: UDP Relay 2.0 bit7: NVRAM bit8: URL table Byte11 bit1: URL super farm bit2: NAT on LAN bit3: Remote Con bit4: AP5000 bit5: Session tracking bit6: Mirroring bit7: Alias IP bit8: CSD Nat Byte12 bit1: content check bit2: mlb virtual ip bit3: reserved RadLan bit4: csd nat exception bit5: statistics monitor bit6: reserved-for-radware
OCT rndBrgLicense	1.3.6.1.4.1.89.2.6	OCTET STRING	read-write	This parameter is used for entering a s/w license number for a device. A separate license number is supplied for each device.
STR rndBrgVersion	1.3.6.1.4.1.89.2.4	DisplayString	read-only	The bridge version.
rndBridgeAlarm	1.3.6.1.4.1.89.2.3
INT rndBridgeType	1.3.6.1.4.1.89.2.1	INTEGER	read-only	Identification of the RND bridge type.
INT rndCommunityAccess	1.3.6.1.4.1.89.2.7.2.1.3	INTEGER	read-write	The allowed access to this management station
rndCommunityEntry	1.3.6.1.4.1.89.2.7.2.1		not-accessible	The row definition for this table.
IP rndCommunityMngStationAddr	1.3.6.1.4.1.89.2.7.2.1.1	IpAddress	read-write	The management station that will be allowed to communicate with the agent IP address
STR rndCommunityOwner	1.3.6.1.4.1.89.2.7.2.1.7	DisplayString	read-write	The owner of this community
INT rndCommunityPortSecurity	1.3.6.1.4.1.89.2.7.2.1.6	INTEGER	read-write	If enabled the device will only receive SNMP messages from the port, through which this NMS is reachable from the device.
INT rndCommunityStatus	1.3.6.1.4.1.89.2.7.2.1.5	INTEGER	read-write	The status of this entry. If the status is invalid the community entry will be deleted
STR rndCommunityString	1.3.6.1.4.1.89.2.7.2.1.2	DisplayString	read-write	The community string with which the management station will communicate with the agent
rndCommunityTable	1.3.6.1.4.1.89.2.7.2		not-accessible	The community table of the agent
INT rndCommunityTrapDestPort	1.3.6.1.4.1.89.2.7.2.1.8	INTEGER	read-write	The transport protocol (usually UDP) port to which traps to the management station represebted by this entry will be sent. The default is the well-known IANA assigned port number for SNMP traps. This object is relevant only if rndCommunityTrapsEnable has a value different from trapsDisable.
INT rndCommunityTrapsEnable	1.3.6.1.4.1.89.2.7.2.1.4	INTEGER	read-write	Should the agent send traps to the management station, and what version is required
rndDeviceParams	1.3.6.1.4.1.89.2
INT rndEndOfMib	1.3.6.1.4.1.89.1000.1	INTEGER	read-only	This variable indicates this is the end of RND MIB.
rndEndOfMibGroup	1.3.6.1.4.1.89.1000
STR rndErrorDesc	1.3.6.1.4.1.89.2.3.1	DisplayString	read-only	A textual description of the enterprise-specific trap sent to the Network Management Station by the RND managed device.
INT rndErrorSeverity	1.3.6.1.4.1.89.2.3.2	INTEGER	read-only	The severity type of the enterprise-specific trap sent to the Network Management Station by the RND managed device.
STR rndImage1Date	1.3.6.1.4.1.89.2.16.1.1.6	DisplayString	read-only	Indicates the compilation date of image-1 in the system.
STR rndImage1Name	1.3.6.1.4.1.89.2.16.1.1.2	DisplayString	read-only	Indicates the file name of image-1 in the system.
STR rndImage1Time	1.3.6.1.4.1.89.2.16.1.1.8	DisplayString	read-only	Indicates the compilation time of image-1 in the system.
STR rndImage1Version	1.3.6.1.4.1.89.2.16.1.1.4	DisplayString	read-only	Indicates the version of image-1 in the system.
STR rndImage2Date	1.3.6.1.4.1.89.2.16.1.1.7	DisplayString	read-only	Indicates the compilation date of image-2 (if present) in the system.If image-2 is not present show 'no info' text
STR rndImage2Name	1.3.6.1.4.1.89.2.16.1.1.3	DisplayString	read-only	Indicates the file name of image-2 (if present) in the system.If image-2 is not present show 'no info' text
STR rndImage2Time	1.3.6.1.4.1.89.2.16.1.1.9	DisplayString	read-only	Indicates the compilation time of image-2 (if present) in the system.If image-2 is not present show 'no info' text
STR rndImage2Version	1.3.6.1.4.1.89.2.16.1.1.5	DisplayString	read-only	Indicates the version of image-2 (if present) in the system.If image-2 is not present show 'no info' text
rndImageInfo	1.3.6.1.4.1.89.2.16
rndImageInfoEntry	1.3.6.1.4.1.89.2.16.1.1		not-accessible	An entry in the rndImageInfoTable.
rndImageInfoTable	1.3.6.1.4.1.89.2.16.1		not-accessible	The table contains information about images.
INT rndImageSize	1.3.6.1.4.1.89.2.14	INTEGER	read-only	Max number of sectors currently allocated for image(s).
INT rndInactiveArpTimeOut	1.3.6.1.4.1.89.2.2	INTEGER	read-write	This variable defines the maximum time period that can pass between ARP requests concerning an entry in the ARP table. After this time period, the entry is deleted from the table.
rndIpHost	1.3.6.1.4.1.89.2.7
rndIpHostManagement	1.3.6.1.4.1.89.2.7.4
INT rndIpHostManagementIfIndex	1.3.6.1.4.1.89.2.7.4.2	INTEGER	read-write	if supported manage , indicate ifindex, if 0 thaen disable
T/F rndIpHostManagementSupported	1.3.6.1.4.1.89.2.7.4.1	TruthValue	read-only	ifindex manage supported.
STR rndManagedDate	1.3.6.1.4.1.89.2.9	DisplayString	read-write	The date will be sent in the format ddmmyy
STR rndManagedTime	1.3.6.1.4.1.89.2.8	DisplayString	read-write	The time will be sent in the format hhmmss
rndMng	1.3.6.1.4.1.89.1
rndNotifications	1.3.6.1.4.1.89.0			All the rnd notifications will reside under this branch as specified in RFC2578 'Structure of Management Information Version 2 (SMIv2)' 8.5
rndSoftwareFile	1.3.6.1.4.1.89.2.13
INT rndStackUnitNumber	1.3.6.1.4.1.89.2.16.1.1.1	INTEGER	read-write	The unit number (for stackable devices) or 1 for 'stand alone' device.
INT rndUnitNumber	1.3.6.1.4.1.89.2.13.1.1.1	INTEGER	read-write	The unit number (for stackable devices) or 1 for 'stand alone' device.
NTF routeTableOverflow	1.3.6.1.4.1.89.0.5			An overflow condition has occurred in the Routing Table. The Routing Table is used for IP routing algorithm (RIP).
NTF rsDhcpAllocationFailure	1.3.6.1.4.1.89.0.142			DHCP failed to allocate an IP address to a requesting host because of memory shortage or inadequate configuration of available IP addresses.
NTF rsIpZhrConnectionsTableOverflow	1.3.6.1.4.1.89.0.70			The Zero Hop Routing connections Table has been overflown.
NTF rsIpZhrNotAllocVirtualIp	1.3.6.1.4.1.89.0.73			The source IP address sent an ARP specifying a virtual IP which was not allocated for this source. This virtual IP will not be allocated to connections of this specific source IP.
NTF rsIpZhrReqStaticConnNotAccepted	1.3.6.1.4.1.89.0.71			The requested static connection was not accepted because there is no available IP virtual address to allocate to it.
NTF rsIpZhrVirtualIpAsSource	1.3.6.1.4.1.89.0.72			The virtual IP address appeared as a source IP. All the connections using it will be deleted and it will not be further allocated to new connections.
NTF rsPingCompletion	1.3.6.1.4.1.89.0.136			A rsPingCompleted trap is sent at the completion of a sequence of pings if such a trap was requested when the sequence was initiated. The trap severity is info. The trap text will specify the following information: rsPingCompletionStatus, rsPingSentPackets, rsPingReceivedPackets In addition to the above listed objects (which are always present), the message will also specify the following quantities: if any responses were received: rsPingMinReturnTime rsPingAvgReturnTime rsPingMaxReturnTime
NTF rsSDclientsTableOverflow	1.3.6.1.4.1.89.0.68			This warning is generated when an overflow occurs in the clients table.
NTF rsSDinactiveServer	1.3.6.1.4.1.89.0.69			This warning is generated when a server does not respond to the dispatchers polling and is thought to be inactive.
NTF rsSnmpSetRequestInSpecialCfgState	1.3.6.1.4.1.89.0.74			An incoming SNMP SET request was rejected because no such requests (except action requests) are accepted after start of new configuration reception or during sending the current configuration to an NMS.
rsTunning	1.3.6.1.4.1.89.29
rsUDP	1.3.6.1.4.1.89.42
NTF rsWSDRedundancySwitch	1.3.6.1.4.1.89.0.141			Whenever main server fails and backup takes over or server comes up after failure a trap of this type is issued.
NTF rxOverflowHWFault	1.3.6.1.4.1.89.0.3			An RX buffer overflow has occurred in one of the LAN or link interfaces. The bound variable rndErrorDesc provides the interface number.
NTF startTftp	1.3.6.1.4.1.89.0.14			Informational trap indicating that the device has intiated a TFTP session. rndErrorDesc will contain the file type in question
NTF stpLoopbackDetection	1.3.6.1.4.1.89.0.205			Warning trap indicating - A loopback was detected on port.
NTF stpLoopbackDetectionResolved	1.3.6.1.4.1.89.0.206			Warning trap indicating - A loopback detection resolved on port.
NTF swIfTablePortLock	1.3.6.1.4.1.89.0.192			Warning trap is indicating port lock hase began.
NTF swIfTablePortUnLock	1.3.6.1.4.1.89.0.193			Warning trap is indicating port lock has ended.
swInterfaces	1.3.6.1.4.1.89.43
NTF txOverflowHWFault	1.3.6.1.4.1.89.0.4			Interport queue overflow has occurred in one of the LAN or link interfaces. The bound variable rndErrorDesc provides the interface number.
vlan	1.3.6.1.4.1.89.48
NTF vlanDynamicToStatic	1.3.6.1.4.1.89.0.173			vlan status was changed from dynamic to static
NTF vlanDynPortAdded	1.3.6.1.4.1.89.0.66
NTF vlanDynPortRemoved	1.3.6.1.4.1.89.0.67
NTF vlanDynVlanAdded	1.3.6.1.4.1.89.0.171			add gvrp dynamic vlan
NTF vlanDynVlanRemoved	1.3.6.1.4.1.89.0.172			remove gvrp dynamic vlan
NTF vlanStaticToDynamic	1.3.6.1.4.1.89.0.174			vlan status was changed from static to dynamic

RFC description

Radlan-private enterprise MIB defining common management objects and OID registrations for Radlan networking devices.

Start monitoring Radlan/Marvell-licensed managed Ethernet switches, OEM switches (base enterprise MIB) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RADLAN-MIB

What Is RADLAN-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description