NTNTECH-INTERFACE-MODULE-CONFIGURATION-MIB

All MIBs › NTNTECH-INTERFACE-MODULE-CONFIGURATION-MIB

Organization: Paradyne Corporation

Last Updated: 2004-11-17

Category: DSL and Broadband Access

Description: Manages DSL interface module line parameters and profile assignment for Paradyne nTech equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is NTNTECH-INTERFACE-MODULE-CONFIGURATION-MIB?

NTNTECH-INTERFACE-MODULE-CONFIGURATION-MIB manages the DSL line-level interface parameters on Paradyne Corporation's nTech IPD12000, IPD4000, and Mini/Micro DSLAM product lines, such as the AAM8000-12/24 and EAM2000-12, configuring per-port DSL and VLAN settings. It exposes per-port configuration tables covering VLAN assignment and ADSL-specific line parameters such as echo-cancellation/FDM mode and fast-path buffering, alongside performance-oriented objects for upstream/downstream signal-to-noise ratio and actual negotiated transmit/receive rates. Its monitoring value is squarely in DSL line performance and hardware status: watching the ADSL SNR and actual sync-rate objects reveals a degrading copper line, excessive noise, or a rate fallback that indicates a physical-layer fault well before a full outage. It complements NTNTECH-CHASSIS-CONFIGURATION-MIB, relying on that MIB's slot/card provisioning to identify which physical port each entry corresponds to. It is deployed on Paradyne/nTech DSLAM and access-multiplexer equipment in telco DSL access networks. Engineers can download the NTNTECH-INTERFACE-MODULE-CONFIGURATION-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in NTNTECH-INTERFACE-MODULE-CONFIGURATION-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Paradyne nTech DSLAM/access multiplexer

Monitoring Examples

An operator polls ifCfgPortAdslTable, via ifCfgPortAdslEntry, for a subscriber port to read ifCfgPortAdslSnrDn and ifCfgPortAdslActualRxRate, then compares them against baseline values recorded at install; a falling SNR paired with a lower actual sync rate indicates line noise or a cabling fault degrading that DSL subscriber's connection.

What Can Be Monitored

per-port ADSL SNR (upstream/downstream)
actual negotiated Tx/Rx rate
VLAN port assignment
ADSL echo cancellation/FDM mode
fast-path buffering configuration

Imported Objects

From NTNTECH-ROOT-MIB

NtnDisplayString
ntntechInterfaceModule	OBJECT-IDENTITY

From SNMPv2-SMI

IpAddress
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT ifCfgAdslPortIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.2	INTEGER	read-only	The physical port number of the ADSL interface.
INT ifCfgAdslSlotIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.1	INTEGER	read-only	The physical slot number of the IPD chassis to which the interface module resides. The Mini/Micro slot index will be 1.
INT ifCfgE1PortIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.7.1.2	INTEGER	read-only	The physical port number of the E1 interface.
INT ifCfgE1SlotIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.7.1.1	INTEGER	read-only	The physical slot number of the IPD chassis to which the interface module resides. The Mini/Micro slot index will be 1.
INT ifCfgIdslPortIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.4.1.2	INTEGER	read-only	The physical port number of the IDSL interface.
INT ifCfgIdslSlotIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.4.1.1	INTEGER	read-only	The physical slot number of the IPD chassis to which the interface module resides. The Mini/Micro slot index will be 1.
INT ifCfgIfPortIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.2.1.2	INTEGER	read-only	The physical port number of the interface.
INT ifCfgIfSlotIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.2.1.1	INTEGER	read-only	The physical slot number of the IPD chassis to which the interface module resides. The Mini/Micro slot index will be 1.
INT ifCfgPortAdslActualDepthDn	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.23	INTEGER	read-only	ADSL dnstream interleaving depth.
INT ifCfgPortAdslActualDepthUp	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.22	INTEGER	read-only	ADSL upstream interleving depth.
INT ifCfgPortAdslActualRxRate	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.19	INTEGER	read-only	ADSL upstream (Rx) data rate. The available upstream data rates range from 32Kbps to 1024Kbps. The upstream data rate can be set by the user via the set value x where x = 1 to 64. The actual data rate that is represented by these set values can be calculated using the following formula, (x * 32Kbps) = upstream data rate, i.e. (3 * 32Kbps) = 96Kbps Note: if an Rx rate value of zero(0) is returned via a GET operation, this would indicate that the port is in 'Adaptive' mode and that the link condition is 'linkdown'.
INT ifCfgPortAdslActualStandardMde	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.21	INTEGER	read-only	ADSL current operating mode, should match ifCfgPortAdslStandardMde UNLESS operating in MULTIMODE
INT ifCfgPortAdslActualTxRate	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.20	INTEGER	read-only	ADSL downstream (Tx) data rates. The available downstream data rates range from 32Kbps to 8064Kbps. The downstream data rate can be set by the user via the set value x where x = 1 to 1024. The actual data rate that is represented by these set values can be calculated using the following formula, (x * 32Kbps) = downstream data rate, i.e. (252 * 32Kbps) = 8064Kbps Note: if a Tx rate value of zero(0) is returned via a GET operation, this would indicate that the port is in 'Adaptive' mode and that the link condition is 'linkdown'.
INT ifCfgPortAdslCorrectionDn	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.12	INTEGER	read-write	ADSL Impulse protection duration in the Upstream duration.
INT ifCfgPortAdslCorrectionUp	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.11	INTEGER	read-write	ADSL Impulse protection duration in the Upstream duration.
INT ifCfgPortAdslDelayDn	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.14	INTEGER	read-write	ADSL Impulse protection duration in the Upstream direction.
INT ifCfgPortAdslDelayUp	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.13	INTEGER	read-write	ADSL Impulse protection duration in the Upstream direction.
INT ifCfgPortAdslEcFdm	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.15	INTEGER	read-write	ADSL Echo Cancellation uses Upstream Tones for Upstream and Dnstream data.
ifCfgPortAdslEntry	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1		not-accessible	An entry containing management information applicable to ADSL module.
INT ifCfgPortAdslFastBuffer	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.16	INTEGER	read-write	Selects fast buffer/low latency. Same is interleave delay of 1ms
INT ifCfgPortAdslFrameType	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.7	INTEGER	read-write	ADSL frame type.
INT ifCfgPortAdslPortMode	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.3	INTEGER	read-write	The port mode of operation, ON, OFF, or Adaptive. When a port is set to Adaptive mode, the best possible value for the Rx/Tx data rates will be achieved. A successful data rate connection will be indicated with a port 'linkup' status.
INT ifCfgPortAdslRxRate	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.5	INTEGER	read-write	ADSL upstream (Rx) data rate. The available upstream data rates range from 32Kbps to 1024Kbps. The upstream data rate can be set by the user via the set value x where x = 1 to 32. The actual data rate that is represented by these set values can be calculated using the following formula, (x * 32Kbps) = upstream data rate, i.e. (3 * 32Kbps) = 96Kbps Note: if an Rx rate value of zero(0) is returned via a GET operation, this would indicate that the port is in 'Adaptive' mode and that the link condition is 'linkdown'.
INT ifCfgPortAdslSnrDn	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.18	INTEGER	read-write	Selects Target Dnstream SNR
INT ifCfgPortAdslSnrUp	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.17	INTEGER	read-write	Selects Target Upstream SNR
INT ifCfgPortAdslStandardMde	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.10	INTEGER	read-write	ADSL standard modes of operation. Note: if receive a standard mode of integer value 255 (0xFF), this would indicate that the standard mode is unknown due to a port 'linkdown' condition.
ifCfgPortAdslTable	1.3.6.1.4.1.8059.1.2.1.1.1.2.3		not-accessible	A list of ADSL interface entries.
INT ifCfgPortAdslTxRate	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.6	INTEGER	read-write	ADSL downstream (Tx) data rates. The available downstream data rates range from 32Kbps to 8064Kbps. The downstream data rate can be set by the user via the set value x where x = 1 to 252. The actual data rate that is represented by these set values can be calculated using the following formula, (x * 32Kbps) = downstream data rate, i.e. (252 * 32Kbps) = 8064Kbps Note: if a Tx rate value of zero(0) is returned via a GET operation, this would indicate that the port is in 'Adaptive' mode and that the link condition is 'linkdown'.
INT ifCfgPortAdslVci	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.9	INTEGER	read-write	ADSL Virtual Channel Identifier (VCI).
INT ifCfgPortAdslVpi	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.8	INTEGER	read-write	ADSL Virtual Path Identifier (VPI) value.
INT ifCfgPortAdslVpiVciDetect	1.3.6.1.4.1.8059.1.2.1.1.1.2.3.1.4	INTEGER	read-write	ADSL Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI) detect mode. If this mode is set to ON, auto-detect the line VPI and VCI values.
INT ifCfgPortBackboneVlan	1.3.6.1.4.1.8059.1.2.1.1.1.2.1.1.8	INTEGER	read-write	The Backbone VLAN tag will become the primary identifier that can be used by routers with backbone capabilities to direct traffic to the appropriate network cloud.
INT ifCfgPortBkBoneEthType	1.3.6.1.4.1.8059.1.2.1.1.1.2.1.1.13	INTEGER	read-write	The value assigned to a port which designates the ethernet packet type.
OCT ifCfgPortCircuitID	1.3.6.1.4.1.8059.1.2.1.1.1.2.1.1.3	OCTET STRING	read-write	The circuit identification number assigned to a port on an interface.
INT ifCfgPortE1ClockSrc	1.3.6.1.4.1.8059.1.2.1.1.1.2.7.1.6	INTEGER	read-write	E1 clock source.
ifCfgPortE1Entry	1.3.6.1.4.1.8059.1.2.1.1.1.2.7.1		not-accessible	An entry containing management information applicable to the E1 interface.
INT ifCfgPortE1FrameType	1.3.6.1.4.1.8059.1.2.1.1.1.2.7.1.4	INTEGER	read-write	E1 frame type.
INT ifCfgPortE1LineCode	1.3.6.1.4.1.8059.1.2.1.1.1.2.7.1.5	INTEGER	read-write	E1 line code.
INT ifCfgPortE1RxTxRate	1.3.6.1.4.1.8059.1.2.1.1.1.2.7.1.3	INTEGER	read-write	E1 symetrical (Rx/Tx) data rates. E1 module types and the associated Rx/Tx data rates- EAM2000-12,EIM2000-12,EIM2000-24: Data Rates (Kbps): 256,512,768,1024,1280,1536,1792,1984 Note: if a rate value of zero(0) is returned via a GET operation, it will indicate that the port is defective.
ifCfgPortE1Table	1.3.6.1.4.1.8059.1.2.1.1.1.2.7		not-accessible	A list of E1 interface entries.
ifCfgPortEntry	1.3.6.1.4.1.8059.1.2.1.1.1.2.1.1		not-accessible	An entry containing management information applicable to the IPD12000, IPD4000 Access/Inverse module as well as the Mini/Micro DSLAM.
INT ifCfgPortFloodMde	1.3.6.1.4.1.8059.1.2.1.1.1.2.1.1.10	INTEGER	read-write	The value assigned to a port which designates the flood mode.
IP ifCfgPortFltrIp1End	1.3.6.1.4.1.8059.1.2.1.1.1.2.1.1.5	IpAddress	read-write	The value assigned to a port which designates the end of the first Ip filter range.
IP ifCfgPortFltrIp1Start	1.3.6.1.4.1.8059.1.2.1.1.1.2.1.1.4	IpAddress	read-write	The value assigned to a port which designates the start of the first Ip filter range.
IP ifCfgPortFltrIp2End	1.3.6.1.4.1.8059.1.2.1.1.1.2.1.1.7	IpAddress	read-write	The value assigned to a port which designates the end of the second Ip filter range.
IP ifCfgPortFltrIp2Start	1.3.6.1.4.1.8059.1.2.1.1.1.2.1.1.6	IpAddress	read-write	The value assigned to a port which designates the start of the second Ip filter range.
ifCfgPortIdslEntry	1.3.6.1.4.1.8059.1.2.1.1.1.2.4.1		not-accessible	An entry containing management information applicable to the IDSL interface.
INT ifCfgPortIdslRxTxRate	1.3.6.1.4.1.8059.1.2.1.1.1.2.4.1.3	INTEGER	read-write	IDSL symetrical (Rx/Tx) data rates. IDSL module types and the associated Rx/Tx data rates- IAM144-12: Data Rates (Kbps): 128,144 Note: if a rate value of zero(0) is returned via a GET operation, it will indicate that the port is defective.
ifCfgPortIdslTable	1.3.6.1.4.1.8059.1.2.1.1.1.2.4		not-accessible	A list of IDSL interface entries.
INT ifCfgPortIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.1.1.2	INTEGER	read-only	The physical port number of the interface.
INT ifCfgPortIpFltProtocol	1.3.6.1.4.1.8059.1.2.1.1.1.2.1.1.11	INTEGER	read-write	The value assigned to a port which designates the IP filter protocol.
INT ifCfgPortReset	1.3.6.1.4.1.8059.1.2.1.1.1.2.1.1.12	INTEGER	read-write	This value is always read as integer value 2. Reset all associated port statistics to zero upon initiation of the reset(1).
ifCfgPortSdslEntry	1.3.6.1.4.1.8059.1.2.1.1.1.2.5.1		not-accessible	An entry containing management information applicable to the SDSL interface.
INT ifCfgPortSdslLineCode	1.3.6.1.4.1.8059.1.2.1.1.1.2.5.1.4	INTEGER	read-write	Line code for the SDSL modules. Note, the line code may be set on the following modules, SIM2000-12,SIM2000-24,SIM2000V-24,SIM2000V-12, or the SDSL micro DSLAM. The line code options are described as follows- CAP: Carrierless Amplitude and Phase modulation 2B1Q: Two Binary, One Quaternary G.SHDSL: Multirate Symmetric Single-pair DSL
INT ifCfgPortSdslRxTxRate	1.3.6.1.4.1.8059.1.2.1.1.1.2.5.1.3	INTEGER	read-write	SDSL symetrical (Rx/Tx) data rates. SDSL module types and the associated Rx/Tx data rates- SAM1000-12: Data Rates (Kbps): 272,528,784,1168 SAM2000-12,SAM2000Q-12,SAM2000G-12,SAM2000D-12,SAM2000DQ-12, SIM2000-24,SuD2011_12T,SuD2011_12E,SuD2003_12T,SuD2003_12E, SuD2011_6T,SuD2011_6E,SuD2002_6T,SuD2002_6E: Data Rates (Kbps): 144,272,400,528,784,1040,1552,2064,2320 SAM2000V-12,SAM2000QV-12,SAM2000GV-12,SIM2000V-12,SIM2000V-24: Data Rates (Kbps): 272,400,528,784,1040,1552,2064,2320 Note: if a rate value of zero(0) is returned via a GET operation, it will indicate that the port is defective.
ifCfgPortSdslTable	1.3.6.1.4.1.8059.1.2.1.1.1.2.5		not-accessible	A list of SDSL interface entries.
INT ifCfgPortT1ClockSrc	1.3.6.1.4.1.8059.1.2.1.1.1.2.6.1.7	INTEGER	read-write	T1 clock source.
ifCfgPortT1Entry	1.3.6.1.4.1.8059.1.2.1.1.1.2.6.1		not-accessible	An entry containing management information applicable to the T1 interface.
INT ifCfgPortT1FrameType	1.3.6.1.4.1.8059.1.2.1.1.1.2.6.1.4	INTEGER	read-write	T1 frame type.
INT ifCfgPortT1LineCode	1.3.6.1.4.1.8059.1.2.1.1.1.2.6.1.5	INTEGER	read-write	T1 line code.
INT ifCfgPortT1RxTxRate	1.3.6.1.4.1.8059.1.2.1.1.1.2.6.1.3	INTEGER	read-write	T1 symetrical (Rx/Tx) data rates. T1 module types and the associated Rx/Tx data rates- TAM1500-12,TIM1500-12,TIM1500-24: Data Rates (Kbps): 192,384,576,768,960,1152,1344,1536 Note: if a rate value of zero(0) is returned via a GET operation, it will indicate that the port is defective.
ifCfgPortT1Table	1.3.6.1.4.1.8059.1.2.1.1.1.2.6		not-accessible	A list of T1 interface entries.
INT ifCfgPortT1TxBuildOut	1.3.6.1.4.1.8059.1.2.1.1.1.2.6.1.6	INTEGER	read-write	T1 tx buildout.
ifCfgPortTable	1.3.6.1.4.1.8059.1.2.1.1.1.2.1		not-accessible	A list of IPD12000, IPD4000 Access/Inverse module and Mini/Micro DSLAM entries.
ifCfgPortVLANEntry	1.3.6.1.4.1.8059.1.2.1.1.1.2.2.1		not-accessible	An entry containing management information applicable to an IPD12000, IPD4000 Access/Inverse module and Mini/Micro DSLAM port.
INT ifCfgPortVlanPriority	1.3.6.1.4.1.8059.1.2.1.1.1.2.1.1.9	INTEGER	read-write	The value assigned to a port which designates the VLAN priority.
ifCfgPortVLANTable	1.3.6.1.4.1.8059.1.2.1.1.1.2.2		not-accessible	A list of IPD12000, IPD4000 Access/Inverse module and Mini/Micro DSLAM port 802.1Q VLAN entries.
INT ifCfgSdslPortIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.5.1.2	INTEGER	read-only	The physical port number of the SDSL interface.
INT ifCfgSdslSlotIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.5.1.1	INTEGER	read-only	The physical slot number of the IPD chassis to which the interface module resides. The Mini/Micro slot index will be 1.
INT ifCfgSlotIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.1.1.1	INTEGER	read-only	The physical slot number of the IPD chassis to which the interface module resides. The Mini/Micro DSLAM will have a slot index value of 1.
INT ifCfgT1PortIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.6.1.2	INTEGER	read-only	The physical port number of the T1 interface.
INT ifCfgT1SlotIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.6.1.1	INTEGER	read-only	The physical slot number of the IPD chassis to which the interface module resides. The Mini/Micro slot index will be 1.
INT ifCfgVLANIdEnd	1.3.6.1.4.1.8059.1.2.1.1.1.2.2.1.5	INTEGER	read-write	The value assigned to a port which designates the end of a VLAN ID range.
INT ifCfgVLANIdStart	1.3.6.1.4.1.8059.1.2.1.1.1.2.2.1.4	INTEGER	read-write	The value assigned to a port which designates the start of a VLAN ID range.
INT ifCfgVLANIndex	1.3.6.1.4.1.8059.1.2.1.1.1.2.2.1.3	INTEGER	read-only	A pointer to one of ten possible VLAN tags that can be assigned to a port.
ifModCfgMIBObjects	1.3.6.1.4.1.8059.1.2.1.1
ifModCfgParameterConfiguration	1.3.6.1.4.1.8059.1.2.1.1.1
ntntechInterfaceModuleConfigurationMIB	1.3.6.1.4.1.8059.1.2.1			This mib module defines an SNMP API to manage Paradyne Corporation's IPD12000, IPD4000, and Mini/Micro DSLAM interface parameters. The interface types are described below, AMD8000-12 12-Port ADSL Mini DSLAMs With Full Rate and G.lite Operational Modes AAM8000-12 12-Port ADSL Access Multiplexer with Full Rate and G.lite Operational Modes AAM8000-24 24-Port ADSL Access Multiplexer with Full Rate and G.lite Operational Modes EAM2000-12 12-Port E1 Access Multiplexer TAM1500-12 12-Port T1 Access Multiplexer IAM144-12 12-Port IDSL Access Multiplexer SAM1000-12 12-Port SDSL Access Multiplexer SAM2000-12, SAM2000Q-12, and SAM2000G-12 12-Port SDSL Access Multiplexers with CAP, 2B1Q or TC/PAM (G.SHDSL) encoding SAM2000D-12 12-Port SDSL Access Multiplexer W/O voice daughter card, running CAP encoding SAM2000DQ-12 12-Port SDSL Access Multiplexer W/O voice daughter card, running 2B1Q encoding SAM2000V-12, SAM2000QV-12, SAM2000GV-12 12-Port SDSL Access Multiplexers with Voice Capability running CAP, 2B1Q or TC/PAM (G.SHDSL) encoding SIM2000-12 12-Port SDSL Access Multiplexer with CAP, 2B1Q and TC/PAM (G.SHDSL) encoding SIM2000-24 24-Port SDSL Access Multiplexer with CAP, 2B1Q and TC/PAM (G.SHDSL) encoding SMD2000-12, SMD2000Q-12, SMD2000G-12 12-Port SDSL Mini DSLAMs: AC and DC Versions with Cap, 2B1Q and G.SHDSL Line encoding SuD2011_12T, SuD2011_12E, SuD2003_12T, SuD2003_12E 12-Port SDSL Micro DSLAMs: Cap, 2B1Q and G.SHDSL Line encoding SuD2011_6T, SuD2011_6E, SuD2002_6T, SuD2002_6E 6-Port SDSL Micro DSLAMs: Cap, 2B1Q and G.SHDSL Line encoding
prmCfgInterface	1.3.6.1.4.1.8059.1.2.1.1.1.1
prmCfgInterfacePort	1.3.6.1.4.1.8059.1.2.1.1.1.2

RFC description

Northern Telecom Technologies vendor-private MIB for interface module configuration and management.

Start monitoring Paradyne nTech DSLAMs/access multiplexers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download NTNTECH-INTERFACE-MODULE-CONFIGURATION-MIB

What Is NTNTECH-INTERFACE-MODULE-CONFIGURATION-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description