HP-SWITCH-BASIC-CONFIG-MIB

All MIBs › HP-SWITCH-BASIC-CONFIG-MIB

Organization: HP Networking

Last Updated: 2015-10-11

Category: Device Management, Vendor: HP/HPE

Description: HP SNMP MIB for basic switch configuration including hostname, location, and fundamental parameters on HP ProCurve switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HP-SWITCH-BASIC-CONFIG-MIB?

HP-SWITCH-BASIC-CONFIG-MIB is an HP Networking proprietary MIB (built on CONFIG-MIB) for basic switch configuration. Its objects cover a save-config action, a CLI-alias table (name, command, row status), a bridge-filter-config table (filter name, drop-port mask, entry status), ACL log-timeout config, IPv4-fragmented-TCP-header-deny and IPv6-non-classifiable-L4-header-deny flags, ACL-grouping-enable, an IGMP-proxy-domain-config table (ID, status, name, IP, multicast range), and a port-copy-name table. As a configuration MIB it lets an administrator confirm CLI aliases, ACL behavior, and IGMP-proxy-domain settings on an HP switch. It is deployed on HP Networking switching equipment (basic configuration). Engineers can download the HP-SWITCH-BASIC-CONFIG-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HP-SWITCH-BASIC-CONFIG-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP Networking switching equipment (basic configuration)

Monitoring Examples

An administrator checks hpSwitchAliasCommand and hpSwitchIgmpProxyDomainIp to confirm CLI alias mappings and IGMP-proxy-domain configuration on an HP switch.

What Can Be Monitored

CLI alias, ACL, and IGMP-proxy-domain configuration

Imported Objects

From CONFIG-MIB

hpSwitchConfig	OBJECT-IDENTITY
hpSwitchFilterConfig	OBJECT-IDENTITY
hpSwitchIgmpConfig	OBJECT-IDENTITY

From ENTITY-MIB

entPhysicalIndex

OBJECT-TYPE

From IF-MIB

InterfaceIndex

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From Q-BRIDGE-MIB

PortList

From SMON-MIB

portCopyEntry

OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus
TruthValue

How to Use in IPNetwork Monitor

Example using hpSwitchRunningCfgChgCount OID:

Select an HP Networking switch (basic config, CLI aliases, ACL/IGMP-proxy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hpSwitchRunningCfgChgCount into the Find box to locate it in the OID tree, then select it and click OK. The total number of running config changes since last reboot. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hpicfBridgeFilterConfigTable	1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.2		not-accessible	A table that contains information about the source port traffic filter configuration in this device.
hpicfBridgeFilterConfigEntry	1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.2.1		not-accessible	Information about a source port traffic filter configuration in this device.
STR hpicfBridgeFilterName	1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.2.1.1	DisplayString	not-accessible	This variable specifies the name of the filter. Filter name can be upto 20 characters. Filter name cannot contain tilde (~). A filter name can not be same as port-name.
POR hpicfBridgeFilterDropPortMask	1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.2.1.2	PortList	read-create	This variable specifies a group of ports to which forwarding of filtered traffic is not permitted.
ROW hpicfBridgeFilterEntryStatus	1.3.6.1.4.1.11.2.14.11.5.1.7.1.8.2.1.3	RowStatus	read-create	Row can be deleted only when no port are mapped to this filter in 'hpSwitchFilterConfigEntry' table.
hpSwitchIgmpProxyDomainConfigTable	1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.5		not-accessible	A table that contains information about the IGMP proxy domain configurations on this switch.
hpSwitchIgmpProxyDomainConfigEntry	1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.5.1		not-accessible	The information associated with each IGMP proxy domain configuration.
I32 hpSwitchIgmpProxyDomainId	1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.5.1.1	Integer32	not-accessible	The domain id that uniquely identifies a row in the IGMP proxy domain configuration table.
ROW hpSwitchIgmpProxyDomainStatus	1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.5.1.2	RowStatus	read-create	The status of a IGMP proxy domain configuration entry. Allows creation/deletion of the IGMP proxy domain entry. Row cannot be deleted if the IGMP proxy domain is associated with a VLAN.
STR hpSwitchIgmpProxyDomainName	1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.5.1.3	DisplayString	read-create	The IGMP proxy domain name.
IP hpSwitchIgmpProxyDomainIp	1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.5.1.4	IpAddress	read-create	The IGMP proxy domain IP.
IP hpSwitchIgmpProxyMcastLowerIp	1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.5.1.5	IpAddress	read-create	The IGMP proxy domain's lower multicast IP.
IP hpSwitchIgmpProxyMcastUpperIp	1.3.6.1.4.1.11.2.14.11.5.1.7.1.15.5.1.6	IpAddress	read-create	The IGMP proxy domain's upper multicast IP.
hpSwitchBasicConfigMIB	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29			This MIB module describes objects for basic switch configuration.
hpSwitchBasicConfigObjects	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1
hpSwitchNotificationObjects	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.0
INT hpSwitchStartupConfigSource	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.0.1	INTEGER	accessible-for-notify	Indicate the method of change to startup config was initiated.
IPt hpSwitchStartupConfigSourceIPAddrType	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.0.2	InetAddressType	accessible-for-notify	Indicates the source address type of network agent which made a change. Not valid (set to zero) if change is made via CLI on system console.
IP hpSwitchStartupConfigSourceIPAddr	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.0.3	InetAddress	accessible-for-notify	Indicates the source address of network agent which made a change. Not valid (set to zero) if change is made via CLI on system console.
STR hpSwitchStartupConfigSourceUsername	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.0.4	DisplayString	accessible-for-notify	Indicates the username of CLI user making the change to startup config. Zero-string if username is not set or change is made via SNMP
T/F hpSwitchStartupConfigThrottled	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.0.5	TruthValue	accessible-for-notify	Indicates if notification throttle was activated and one or more notifications were dropped.
NTF hpSwitchStartupConfigChange	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.0.6			The hpSwitchStartupConfigChange notification signifies that switch's startup config was modified by user/manager. Notifications might be buffered on the system to be sent after throttle delay. In some cases, notifications will be dropped. At such event the next transmitted notification will set flag hpSwitchStartupConfigThrottled
NTF hpSwitchRunningConfigChange	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.0.7			Notification of a running configuration change event as recorded in hpSwitchRunningCfgChgTable.
INT hpSwitchSaveConfig	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.1	INTEGER	read-write	When this object is set to to 'saveConfig' it results in saving the running configuration of the switch to flash. The saved configuration becomes the boot-up configuration of the switch when it boots next time. When read, this object always returns 'noConfigSave'.
hpSwitchAliasTable	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.2		not-accessible	Table of alias configurations for CLI commands. This table contains information about name of the alias and the corresponding CLI command.
hpSwitchAliasEntry	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.2.1		not-accessible	A row in the alias config table.
STR hpSwitchAliasName	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.2.1.1	DisplayString	not-accessible	Name of the alias which uniquely identifies alias configuration table. 'hpSwitchAliasName' can be used in place of 'hpSwitchAliasCommand` on the CLI. Maximum allowed length for alias name is 32 characters.
OCT hpSwitchAliasCommand	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.2.1.2	OCTET STRING	read-create	CLI command for which 'hpSwitchAliasName' can be used in CLI. Maximum allowed length for alias command is 255 characters. This object is required to create an entry in the table.
ROW hpSwitchAliasConfigRowStatus	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.2.1.3	RowStatus	read-create	Controls creation/deletion of entries in alias table. Row cant be created when 'hpSwitchAliasCommand' is of zero length. Row transition to 'notReady' or 'notInService' states are not allowed.
hpSwitchACLConfig	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.3
I32 hpSwitchAclLogtimeoutConfig	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.3.1	Integer32	read-write	The time in seconds between ACL logging summary messages. Some devices may limit the range to 30..300.
INT hpSwitchAclIpv4DenyFragmentedTcpHeader	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.3.2	INTEGER	read-write	Configure the device to drop all IPv4 packets containing a fragmented TCP header.
INT hpSwitchAclIpv6DenyNonClassifiableL4Header	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.3.3	INTEGER	read-write	Configure the device to drop all IPv6 packets for which the Layer 4 header cannot be processed by ACL hardware.
T/F hpSwitchAclGroupingEnable	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.3.4	TruthValue	read-write	This object enables or disables ACL Grouping support. When set to true(1), ACL Grouping will allow for the sharing of hardware entries from an ACL with the same name and type and applied in the same direction when the hpicfGppcv2AcSharedFlag is used to apply the ACL. When set to false(2), entries will be unshared.
hpicfPortCopyNameTable	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.4		not-accessible	This table contains Mirroring Destination name String.
hpicfPortCopyNameEntry	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.4.1		not-accessible	An entry in the hpicfPortCopyNameEntry contains Mirroring Destination name string.
STR hpicfPortCopyName	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.4.1.1	DisplayString	read-create	Mirroring Destination name string.
INT hpSwitchDefaultLogon	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.5	INTEGER	read-write	This indicates whether switch should boot to CLI (default) or menu. The changes takes effect after rebooting the switch.
hpSwitchChassisLocateTable	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.6		not-accessible	This table is contains information about the current state of all the chassis locate LEDs.
hpSwitchChassisLocateEntry	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.6.1		not-accessible	Contains information about the current state of a particular chassis LED.
INT hpSwitchChassisLocateState	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.6.1.1	INTEGER	read-write	The current state of the chassis locate LED.
I32 hpSwitchChassisLocateDuration	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.6.1.2	Integer32	read-write	The duration for which the current LED state is to be maintained. The minimum value is 60 and the maximum value is 86400. The 'off' state does not require a duration. A get request for the duration when the state is 'off' will return the default duration value.
INT hpSwitchChassisLocateWhen	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.6.1.3	INTEGER	read-write	When to apply the values specified by hpSwitchChassisLocateState and hpSwitchChassisLocateDuration. If not specified, the default is now.
hpSwitchModules	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.7
hpSwitchModuleInfoTable	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.7.1		not-accessible	A table describing all modules that can be supported by the device.
hpSwitchModuleInfoEntry	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.7.1.1		not-accessible	The information regarding the module type in the switch. This table lists all the supported module types. The supported module type will have the equivalent module name.
I32 hpSwitchModuleInfoModId	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.7.1.1.1	Integer32	not-accessible	The module Id. This is a sequence number
STR hpSwitchModuleInfoModType	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.7.1.1.2	DisplayString	read-only	The module type in the switch. This is the Jnumber string that is supported on the device.
hpSwitchModuleConfigTable	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.7.2		not-accessible	A table to configure the module type for a specific module.
hpSwitchModuleConfigEntry	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.7.2.1		not-accessible	This entry is used to configure the module type for a specific module. Configuration of module type is not allowed if it is already configured.
STR hpSwitchModuleConfigModType	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.7.2.1.1	DisplayString	read-write	The module type in the switch. This is the Jnumber supported on the device. The supported types are listed in hpSwitchModuleInfoTable.
STR hpSwitchModuleConfigModName	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.7.2.1.2	DisplayString	read-only	The module name in the switch.
T/F hpSwitchModuleConfigModRemove	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.7.2.1.3	TruthValue	read-write	This MIB object is used to remove the slot configuration. Setting this object to true (1) will remove the module configuration. Default value is false (2). This object should always returns false (2). The module can be configured by setting the hpSwitchModuleConfigModType to a supported Jnumber on the device.
STR hpSwitchWebSupportUrl	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.8	DisplayString	read-write	URL for the web interface support page.
U32 hpSwitchStartupConfigSeqNum	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.9	Unsigned32	read-write	This is the value of the global startup-config sequential number. Every change to startup-config increments the value by 1. Must be stored in non-volatile memory to be carried over the system boot.
INT hpSwitchStartupConfigNotifyEnable	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.10	INTEGER	read-write	Indicates whether the SNMP entity is permitted to generate hpSwitchStartupConfigChange notifications. Default is disabled.
INT hpSwitchImplicitConfigSave	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.11	INTEGER	read-write	This object is to enable/disable the implicit write-memory (saving the running-config to the flash) done after every successful SNMP set operation. When set to 'enable', config changes are written to the flash which results in slow performance for these set operations. To get faster processing while doing large number of continuous SNMP set operations, this object can be set to 'disable'; And,once the SNMP set operations are done, 'hpSwitchSaveConfig' MIB object can be used to save the running-config to the flash. This object will not be saved across a re-boot, and will always be set to 'enable' at boot. It is advisable to set this MIB object to 'disable' only when there are a lot of continuous SNMP set operations e.g. a script executing a large number of SNMP set operations.
hpSwitchRunningCfgChgObjects	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12
INT hpSwitchRunningCfgChgNotifyEnable	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12.1	INTEGER	read-write	Indicates whether the SNMP entity is permitted to generate hpSwitchRunningConfigChange notifications. Default is disabled.
U32 hpSwitchRunningCfgChgTransmitInterval	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12.2	Unsigned32	read-write	Specifies the transmission interval in seconds for sending running config change traps. Only one running config change trap is sent in this time interval. Default value is 0, indicating there is no limit on sending running config change traps.
DAT hpSwitchRunningCfgChgLatestDateAndTime	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12.3	DateAndTime	read-only	Indicates the date and time of the most recent running config change.
C32 hpSwitchRunningCfgChgCountEx	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12.4	Counter32	read-only	The total number of running config changes since last reboot.
C32 hpSwitchRunningCfgChgEntriesBumped	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12.5	Counter32	read-only	The number of times the oldest entry in hpSwitchRunningCfgChgTable was discarded to make room for a new entry.
hpSwitchRunningCfgChgEventTable	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12.6		not-accessible	A table of latest 32 running configuration change events.
hpSwitchRunningCfgChgEventEntry	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12.6.1		not-accessible	Information about running configuration change event on this switch.
I32 hpSwitchRunningCfgChgEventTableIndex	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12.6.1.1	Integer32	not-accessible	The Index for hpSwitchRunningCfgChgTable.
U32 hpSwitchRunningCfgChgEventId	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12.6.1.2	Unsigned32	read-only	Identifies a specific running config change. Monotonically increasing values will be assigned by the system to each event as it occurs. If the system is reset, these event ID values will be reset as well.
INT hpSwitchRunningCfgChgEventMethod	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12.6.1.3	INTEGER	read-only	Indicates the source through which change to running config was initiated.
IPt hpSwitchRunningCfgChgEventSourceIPAddrType	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12.6.1.4	InetAddressType	read-only	Indicates the source address type of network agent which made a change. This object value is set to an address type of unknown when not applicable.
IP hpSwitchRunningCfgChgEventSourceIPAddr	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12.6.1.5	InetAddress	read-only	Indicates the source address of network agent which made a running config change. The value is an address of length 0 (unknown(0)) if not available or not applicable.
STR hpSwitchRunningCfgChgEventUsername	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12.6.1.6	DisplayString	read-only	Indicates the username of the user making the change the change to running config. Empty string (length 0) if username is not available or not applicable.
DAT hpSwitchRunningCfgChgEventDateAndTime	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.12.6.1.7	DateAndTime	read-only	Indicates the date and time of the running config change.
INT hpSwitchSecureModeLevel	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.13	INTEGER	read-write	Indicates current Secure-Mode Level of switch standard : switch operates with standard security capabilities. enhanced : switch operates with enhanced security capabilities for configurations to satisfy FIPS 140-2 requirements.The default level is standard.
INT hpSwitchCdpRunMode	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.14	INTEGER	read-write	Indicates the mode of CDP processing. This variable has no effect when CDP is disabled (cdpGlobalRun = FALSE).
hpSwitchCdpObjects	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.15
hpSwitchCdpPreStdVoiceTable	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.15.1		not-accessible	Information about cdp pre-standard-voice admin status for each port in this device.
hpSwitchCdpPreStdVoiceEntry	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.15.1.1		not-accessible	Information about cdp pre-standard-voice admin status for a switch port.
NUM hpSwitchCdpPreStdVoiceIfIndex	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.15.1.1.1	InterfaceIndex	not-accessible	The ifIndex value of the local interface.
INT hpSwitchCdpPreStdVoiceStatus	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.15.1.1.2	INTEGER	read-write	Indicates the admin status for cdp pre-standard-voice mode for this cdpInterfaceIfIndex entry Default is txAndRx and this value is valid only if hpSwitchCdpRunMode is 'preStdVoice(3)' .
POR hpSwitchIgnoreUntagMacPortList	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.16	PortList	read-write	Prevent learning MAC addresses on the specified ports when the VLAN is untagged and the destination MAC address is one of the following: 01000C-CCCCCC (CDP) 0180c2-00000e (LLDP) 0180c2-000003 (EAPOL)
INT hpSwitchControlPlaneProtectionAdminStatus	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.17	INTEGER	read-write	The operational status of the Control Plane Protection feature. When Control Plane Protection feature is enabled on a device, if the number of IP error packets exceed the threshold value they are dropped at the data plane. This eliminates the processing of error packets by control plane, thereby reducing the load on the CPU.
hpSwitchFPModules	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.19
hpSwitchFPModuleConfigTable	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.19.1		not-accessible	A table that contains the configuration details for flexible modules.
hpSwitchFPModuleConfigEntry	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.19.1.1		not-accessible	An entry in the table that contains the configuration details of a flexible module.
INT hpSwitchFPModuleConfigType	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.19.1.1.1	INTEGER	read-write	The J-Number of the flexible module. When set to a value other than none, the value can only be changed to none. Setting this object to none (0) erases the flexible module configuration .
STR hpSwitchFPModuleConfigName	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.19.1.1.2	DisplayString	read-write	The flexible module name in the switch. Some devices do not support configuration of the flexible module name and will return an error if this object is set.
INT hpSwitchRESTInterfaceStatus	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.20	INTEGER	read-write	The object that can be used to enable or disable the REST interface. The default value is enable.
I32 hpSwitchRESTSessionIdleTimeout	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.1.21	Integer32	read-write	The time period after which the REST session timeout occurs. A user can configure this parameter. The default value is 600 seconds.
hpSwitchBasicConfigConformance	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2
hpSwitchBasicConfigCompliances	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.1
hpSwitchBasicConfigCompliance	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.1.1			The compliance statement for config entities which implements basic configuration of the switch.
hpSwitchBasicConfigCompliance2	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.1.2			The compliance statement for config entities which implements basic configuration of the switch.
hpSwitchBasicConfigCompliance3	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.1.3			The compliance statement for config entities which implements basic configuration of the switch.
hpSwitchBasicConfigCompliance4	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.1.4			The compliance statement for config entities which implements basic configuration of the switch.
hpSwitchBasicConfigCompliance5	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.1.5			The compliance statement for config entities which implements basic configuration of the switch.
hpSwitchBasicConfigCompliance6	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.1.6			The compliance statement for config entities which implements basic configuration of the switch.
hpSwitchBasicConfigCompliance7	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.1.7			The compliance statement for config entities which implements the basic configuration of the switch.
hpSwitchBasicConfigCompliance8	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.1.8			The compliance statement for entities that implement the Control Plane Protection feature on a device.
hpSwitchBasicConfigCompliance10	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.1.10			The compliance statement for entities that implement the flexible Module configuration on a device.
hpSwitchBasicConfigCompliance11	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.1.11			The compliance statement for entities that implement the REST interface configuration on a device.
hpSwitchBasicConfigCompliance12	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.1.12			The compliance statement for config entities which implements basic configuration of the switch.
hpSwitchBasicConfigGroups	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2
hpSwitchBasicConfigGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.1			A collection of objects for basic configuration of the switch.
hpSwitchAliasGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.2			A collection of objects for alias configuration for CLI commands.
hpicfBridgeFilterConfigGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.3			A collection of objects for source-port filter configuration.
hpicfPortCopyNameGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.4			A collection of objects for mirror configuration for CLI commands.
hpSwitchAclLogtimeoutGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.5			A collection of objects for ACL log timeout configuration of the switch.
hpSwitchIgmpProxyDomainConfigGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.6			A collection of objects for IGMP proxy domain configuration.
hpSwitchChassisLocateGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.7			A collection of objects for chassis locate configuration.
hpSwitchModuleGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.8			A collection of objects for switch module configuration.
hpSwitchStartupConfigChangeGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.9			A collection of objects for startup config change notifications.
hpSwitchBasicConfigGroup2	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.10			A collection of objects for switch basic configurations.
hpSwitchRunningCfgChgGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.11			A collection of objects for running config change details and its notification.
hpSwitchBasicConfigGroup3	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.12			A collection of objects for switch Secure mode configurations.
hpSwitchCdpConfigGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.13			A collection of objects for Cisco discovery protocol mode configurations.
hpSwitchCdpPreStdVoiceGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.14			A collection of objects for Cisco discovery protocol mode configurations.
hpSwitchIgnoreUntagMacConfigGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.15			A collection of objects for Ignore untag MAC configurations.
hpSwitchModuleConfigGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.16			Group of objects representing module configuration.
hpSwitchBasicConfigGroup4	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.17			A collection of objects to configure the Control Plane Protection on a device.
hpSwitchAclGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.20			A collection of objects to configure ACL options on a device.
hpSwitchFPModuleGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.21			A collection of objects for switch flexible module configuration.
hpSwitchRESTInterfaceGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.22			A collection of objects for the Representational State Transfer (REST) interface configuration.
hpSwitchAclGroupingEnableGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.2.23			A collection of objects to configure ACL Grouping options on a device.
hpSwitchBasicNotificationGroups	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.3
hpSwitchBasicNotificationGroup	1.3.6.1.4.1.11.2.14.11.5.1.7.1.29.2.3.1			Switch Basic Config notifications

RFC description

MIB module for basic switch configuration including ACLs, IGMP, and module management.

Start monitoring HP Networking switch (basic config, CLI aliases, ACL/IGMP-proxy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HP-SWITCH-BASIC-CONFIG-MIB