GE-PARALLELUPS

All MIBs › GE-PARALLELUPS

Description: GE-PARALLELUPS module

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is GE-PARALLELUPS?

GE-PARALLELUPS is a General Electric (enterprise OID 818) proprietary MIB reporting status for parallel-redundant UPS installations, built on generic UPS objects modeled after RFC 1628. Its objects cover a discovered-UPS bitmask, request/reply packet objects, and generic UPS identity (manufacturer, model, software version, agent version, name, attached devices, serial number, protocol version, operating time), battery status (status, seconds on battery, estimated minutes/charge remaining, voltage, current, temperature), and an input-line table (bad-line count, line count, per-line frequency). As a status/performance MIB it lets an administrator watch battery runtime and input-line quality across a GE parallel UPS bank. It is deployed on GE parallel-redundant UPS installations. Engineers can download the GE-PARALLELUPS file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in GE-PARALLELUPS. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

GE parallel-redundant UPS installations

Monitoring Examples

An administrator checks upsEstimatedMinutesRemaining-gen and upsBatteryStatus-gen to confirm runway remaining during a power outage on a GE parallel UPS installation.

What Can Be Monitored

battery runtime and input-line quality

Imported Objects

From SNMPv2-SMI

Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE
enterprises

From SNMPv2-TC

AutonomousType
DisplayString
TEXTUAL-CONVENTION
TestAndIncr
TimeInterval
TimeStamp

OIDs

OID symbolic	OID numeric	Type	Access	Description
imv	1.3.6.1.4.1.818
geHardware	1.3.6.1.4.1.818.1
geUPS	1.3.6.1.4.1.818.1.1
I32 geDiscoveredUPSsMask	1.3.6.1.4.1.818.1.1.1	Integer32	read-only	Reading this variable returns bit mask indicating which UPSs in a parallel system are alive. Management software should poll only these UPSs on their snmp branches 11-18 as follows: 1 FirstUPS alive 2 SecondUPS alive 4 ThirdUPS alive 8 FourthUPS alive 16 FifthUPS alive 32 SixthUPS alive 64 SeventhUPS alive 128 EigthUPS alive Since the management software should always monitor the GenericUPS branch (10), this value has no meaning for single upses (which provide values on that snmp branch), and should be set to zero in that case.
STR geRequestPacket	1.3.6.1.4.1.818.1.1.2	DisplayString	read-write	Put the string, formatted as a IMV/CP4 packet, directly to internally RS485 bus. This OID could be used for accede directly to the internally RS485 bus from a remote place.
STR geReplyPacket	1.3.6.1.4.1.818.1.1.3	DisplayString	read-only	Contain the reply of the IMV/CP4 request packet sent using the OID geRequestPacket. Every time that a write command has be made at the OID ge RequestPacket, the value of this OID is erased.
geGenericUPS	1.3.6.1.4.1.818.1.1.10
upsIdent_gen	1.3.6.1.4.1.818.1.1.10.1
STR upsIdentManufacturer_gen	1.3.6.1.4.1.818.1.1.10.1.1	DisplayString	read-only	The name of the UPS manufacturer.(*)
STR upsIdentModel_gen	1.3.6.1.4.1.818.1.1.10.1.2	DisplayString	read-only	The UPS Model designation.(*)
STR upsIdentUPSSoftwareVersion_gen	1.3.6.1.4.1.818.1.1.10.1.3	DisplayString	read-only	The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)
STR upsIdentAgentSoftwareVersion_gen	1.3.6.1.4.1.818.1.1.10.1.4	DisplayString	read-only	The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)
STR upsIdentName_gen	1.3.6.1.4.1.818.1.1.10.1.5	DisplayString	read-write	A string identifying the UPS. This object should be set by the administrator.(*)
STR upsIdentAttachedDevices_gen	1.3.6.1.4.1.818.1.1.10.1.6	DisplayString	read-write	A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)
STR upsIdentUPSSerialNumber_gen	1.3.6.1.4.1.818.1.1.10.1.7	DisplayString	read-only	The UPS serial number
STR upsIdentComProtVersion_gen	1.3.6.1.4.1.818.1.1.10.1.8	DisplayString	read-only	The IMV communication protocol version
NUM upsIdentOperatingTime_gen	1.3.6.1.4.1.818.1.1.10.1.9	NonNegativeInteger32	read-only	The present value of the operating time. total 'on' time since UPS manufactured
upsBattery_gen	1.3.6.1.4.1.818.1.1.10.2
INT upsBatteryStatus_gen	1.3.6.1.4.1.818.1.1.10.2.1	INTEGER	read-only	The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)
NUM upsSecondsOnBattery_gen	1.3.6.1.4.1.818.1.1.10.2.2	NonNegativeInteger32	read-only	If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)
NUM upsEstimatedMinutesRemaining_gen	1.3.6.1.4.1.818.1.1.10.2.3	PositiveInteger32	read-only	An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)
I32 upsEstimatedChargeRemaining_gen	1.3.6.1.4.1.818.1.1.10.2.4	Integer32	read-only	An estimate of the battery charge remaining expressed as a percent of full charge.(*)
NUM upsBatteryVoltage_gen	1.3.6.1.4.1.818.1.1.10.2.5	NonNegativeInteger32	read-only	The magnitude of the present battery voltage.(*)
I32 upsBatteryCurrent_gen	1.3.6.1.4.1.818.1.1.10.2.6	Integer32	read-only	The present battery current.(*)
I32 upsBatteryTemperature_gen	1.3.6.1.4.1.818.1.1.10.2.7	Integer32	read-only	The ambient temperature at or near the UPS Battery casing.(*)
upsInput_gen	1.3.6.1.4.1.818.1.1.10.3
C32 upsInputLineBads_gen	1.3.6.1.4.1.818.1.1.10.3.1	Counter32	read-only	A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)
NUM upsInputNumLines_gen	1.3.6.1.4.1.818.1.1.10.3.2	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)
upsInputTable_gen	1.3.6.1.4.1.818.1.1.10.3.3		not-accessible	A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)
upsInputEntry_gen	1.3.6.1.4.1.818.1.1.10.3.3.1		not-accessible	An entry containing information applicable to a particular input line.(*)
NUM upsInputLineIndex_gen	1.3.6.1.4.1.818.1.1.10.3.3.1.1	PositiveInteger32	not-accessible	The input line identifier.(*)
NUM upsInputFrequency_gen	1.3.6.1.4.1.818.1.1.10.3.3.1.2	NonNegativeInteger32	read-only	The present input frequency.(*)
NUM upsInputVoltage_gen	1.3.6.1.4.1.818.1.1.10.3.3.1.3	NonNegativeInteger32	read-only	The magnitude of the present input voltage.(*)
NUM upsInputCurrent_gen	1.3.6.1.4.1.818.1.1.10.3.3.1.4	NonNegativeInteger32	read-only	The magnitude of the present input current.(*)
NUM upsInputTruePower_gen	1.3.6.1.4.1.818.1.1.10.3.3.1.5	NonNegativeInteger32	read-only	The magnitude of the present input true power.(*)
NUM upsInputVoltageMin_gen	1.3.6.1.4.1.818.1.1.10.3.3.1.6	NonNegativeInteger32	read-only	The lowest magnitude of the input voltage since last read out.
NUM upsInputVoltageMax_gen	1.3.6.1.4.1.818.1.1.10.3.3.1.7	NonNegativeInteger32	read-only	The highest magnitude of the input voltage since last read out.
upsOutput_gen	1.3.6.1.4.1.818.1.1.10.4
INT upsOutputSource_gen	1.3.6.1.4.1.818.1.1.10.4.1	INTEGER	read-only	The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)
NUM upsOutputFrequency_gen	1.3.6.1.4.1.818.1.1.10.4.2	NonNegativeInteger32	read-only	The present output frequency.(*)
NUM upsOutputNumLines_gen	1.3.6.1.4.1.818.1.1.10.4.3	NonNegativeInteger32	read-only	The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)
upsOutputTable_gen	1.3.6.1.4.1.818.1.1.10.4.4		not-accessible	A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)
upsOutputEntry_gen	1.3.6.1.4.1.818.1.1.10.4.4.1		not-accessible	An entry containing information applicable to a particular output line.(*)
NUM upsOutputLineIndex_gen	1.3.6.1.4.1.818.1.1.10.4.4.1.1	PositiveInteger32	not-accessible	The output line identifier.(*)
NUM upsOutputVoltage_gen	1.3.6.1.4.1.818.1.1.10.4.4.1.2	NonNegativeInteger32	read-only	The present output voltage.(*)
NUM upsOutputCurrent_gen	1.3.6.1.4.1.818.1.1.10.4.4.1.3	NonNegativeInteger32	read-only	The present output current.(*)
NUM upsOutputPower_gen	1.3.6.1.4.1.818.1.1.10.4.4.1.4	NonNegativeInteger32	read-only	The present output true power.(*)
I32 upsOutputPercentLoad_gen	1.3.6.1.4.1.818.1.1.10.4.4.1.5	Integer32	read-only	The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)
upsBypass_gen	1.3.6.1.4.1.818.1.1.10.5
NUM upsBypassFrequency_gen	1.3.6.1.4.1.818.1.1.10.5.1	NonNegativeInteger32	read-only	The present bypass frequency.(*)
NUM upsBypassNumLines_gen	1.3.6.1.4.1.818.1.1.10.5.2	NonNegativeInteger32	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)
upsBypassTable_gen	1.3.6.1.4.1.818.1.1.10.5.3		not-accessible	A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)
upsBypassEntry_gen	1.3.6.1.4.1.818.1.1.10.5.3.1		not-accessible	An entry containing information applicable to a particular bypass input.(*)
NUM upsBypassLineIndex_gen	1.3.6.1.4.1.818.1.1.10.5.3.1.1	PositiveInteger32	not-accessible	The bypass line identifier.(*)
NUM upsBypassVoltage_gen	1.3.6.1.4.1.818.1.1.10.5.3.1.2	NonNegativeInteger32	read-only	The present bypass voltage.(*)
NUM upsBypassCurrent_gen	1.3.6.1.4.1.818.1.1.10.5.3.1.3	NonNegativeInteger32	read-only	The present bypass current.(*)
NUM upsBypassPower_gen	1.3.6.1.4.1.818.1.1.10.5.3.1.4	NonNegativeInteger32	read-only	The present true power conveyed by the bypass.(*)
upsAlarm_gen	1.3.6.1.4.1.818.1.1.10.6
G32 upsAlarmsPresent_gen	1.3.6.1.4.1.818.1.1.10.6.1	Gauge32	read-only	The present number of active alarm conditions.(*)
upsAlarmTable_gen	1.3.6.1.4.1.818.1.1.10.6.2		not-accessible	A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)
upsAlarmEntry_gen	1.3.6.1.4.1.818.1.1.10.6.2.1		not-accessible	An entry containing information applicable to a particular alarm.(*)
NUM upsAlarmId_gen	1.3.6.1.4.1.818.1.1.10.6.2.1.1	PositiveInteger32	not-accessible	A unique identifier for an alarm condition. This value must remain constant.(*)
OID upsAlarmDescr_gen	1.3.6.1.4.1.818.1.1.10.6.2.1.2	AutonomousType	read-only	A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)
TIM upsAlarmTime_gen	1.3.6.1.4.1.818.1.1.10.6.2.1.3	TimeStamp	read-only	The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)
upsWellKnownAlarms_gen	1.3.6.1.4.1.818.1.1.10.6.3
upsAlarmBatteryBad_gen	1.3.6.1.4.1.818.1.1.10.6.3.1			One or more batteries have been determined to require replacement.(*)
upsAlarmOnBattery_gen	1.3.6.1.4.1.818.1.1.10.6.3.2			The UPS is drawing power from the batteries.(*)
upsAlarmLowBattery_gen	1.3.6.1.4.1.818.1.1.10.6.3.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)
upsAlarmDepletedBattery_gen	1.3.6.1.4.1.818.1.1.10.6.3.4			The UPS will be unable to sustain the present load when and if the utility power is lost.(*)
upsAlarmTempBad_gen	1.3.6.1.4.1.818.1.1.10.6.3.5			A temperature is out of tolerance.(*)
upsAlarmInputBad_gen	1.3.6.1.4.1.818.1.1.10.6.3.6			An input condition is out of tolerance.(*)
upsAlarmOutputBad_gen	1.3.6.1.4.1.818.1.1.10.6.3.7			An output condition (other than OutputOverload) is out of tolerance.(*)
upsAlarmOutputOverload_gen	1.3.6.1.4.1.818.1.1.10.6.3.8			The output load exceeds the UPS output capacity.(*)
upsAlarmOnBypass_gen	1.3.6.1.4.1.818.1.1.10.6.3.9			The Bypass is presently engaged on the UPS.(*)
upsAlarmBypassBad_gen	1.3.6.1.4.1.818.1.1.10.6.3.10			The Bypass is out of tolerance.(*)
upsAlarmOutputOffAsRequested_gen	1.3.6.1.4.1.818.1.1.10.6.3.11			The UPS has shutdown as requested, i.e., the output is off.(*)
upsAlarmUpsOffAsRequested_gen	1.3.6.1.4.1.818.1.1.10.6.3.12			The entire UPS has shutdown as commanded.(*)
upsAlarmChargerFailed_gen	1.3.6.1.4.1.818.1.1.10.6.3.13			An uncorrected problem has been detected within the UPS charger subsystem.(*)
upsAlarmUpsOutputOff_gen	1.3.6.1.4.1.818.1.1.10.6.3.14			The output of the UPS is in the off state.(*)
upsAlarmUpsSystemOff_gen	1.3.6.1.4.1.818.1.1.10.6.3.15			The UPS system is in the off state.(*)
upsAlarmFanFailure_gen	1.3.6.1.4.1.818.1.1.10.6.3.16			The failure of one or more fans in the UPS has been detected.(*)
upsAlarmFuseFailure_gen	1.3.6.1.4.1.818.1.1.10.6.3.17			The failure of one or more fuses has been detected.(*)
upsAlarmGeneralFault_gen	1.3.6.1.4.1.818.1.1.10.6.3.18			A general fault in the UPS has been detected.(*)
upsAlarmDiagnosticTestFailed_gen	1.3.6.1.4.1.818.1.1.10.6.3.19			The result of the last diagnostic test indicates a failure.(*)
upsAlarmCommunicationsLost_gen	1.3.6.1.4.1.818.1.1.10.6.3.20			A problem has been encountered in the communications between the agent and the UPS.(*)
upsAlarmAwaitingPower_gen	1.3.6.1.4.1.818.1.1.10.6.3.21			The UPS output is off and the UPS is awaiting the return of input power.(*)
upsAlarmShutdownPending_gen	1.3.6.1.4.1.818.1.1.10.6.3.22			A upsShutdownAfterDelay countdown is underway.(*)
upsAlarmShutdownImminent_gen	1.3.6.1.4.1.818.1.1.10.6.3.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)
upsAlarmTestInProgress_gen	1.3.6.1.4.1.818.1.1.10.6.3.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)
upsAlarmReceptacleOff_gen	1.3.6.1.4.1.818.1.1.10.6.3.25			The receptacle are switch off
NUM upsAlarmMaskA_gen	1.3.6.1.4.1.818.1.1.10.6.4	NonNegativeInteger32	read-only	Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.
upsTest_gen	1.3.6.1.4.1.818.1.1.10.7
OID upsTestId_gen	1.3.6.1.4.1.818.1.1.10.7.1	OBJECT IDENTIFIER	read-write	The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)
TES upsTestSpinLock_gen	1.3.6.1.4.1.818.1.1.10.7.2	TestAndIncr	read-write	A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: try-again: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager / short delay get (upsTestSpinLock) } lock-value = upsTestSpinLock / no test in progress, start the test / set (upsTestSpinLock = lock-value, upsTestId = requested-test) if (error-index == 1) { / (upsTestSpinLock failed) / / if problem is not access control, then some other manager slipped in ahead of us / goto try-again } if (error-index == 2) { / (upsTestId) / / cannot perform the test / give up } / test started ok / / wait for test completion by polling upsTestResultsSummary / get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } / when test completes, retrieve any additional test results / / if upsTestSpinLock == lock-value + 1, then these are our test / / results (as opposed to another manager's / The initial value of upsTestSpinLock at agent initialization shall be 1.()
INT upsTestResultsSummary_gen	1.3.6.1.4.1.818.1.1.10.7.3	INTEGER	read-only	The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)
STR upsTestResultsDetail_gen	1.3.6.1.4.1.818.1.1.10.7.4	DisplayString	read-only	Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)
TIM upsTestStartTime_gen	1.3.6.1.4.1.818.1.1.10.7.5	TimeStamp	read-only	The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)
NUM upsTestElapsedTime_gen	1.3.6.1.4.1.818.1.1.10.7.6	TimeInterval	read-only	The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)
upsWellKnownTests_gen	1.3.6.1.4.1.818.1.1.10.7.7
upsTestNoTestsInitiated_gen	1.3.6.1.4.1.818.1.1.10.7.7.1			No tests have been initiated and no test is in progress.(*)
upsTestAbortTestInProgress_gen	1.3.6.1.4.1.818.1.1.10.7.7.2			The test in progress is to be aborted / the test in progress was aborted.(*)
upsTestGeneralSystemsTest_gen	1.3.6.1.4.1.818.1.1.10.7.7.3			The manufacturer's standard test of UPS device systems.(*)
upsTestQuickBatteryTest_gen	1.3.6.1.4.1.818.1.1.10.7.7.4			A test that is sufficient to determine if the battery needs replacement.(*)
upsTestDeepBatteryCalibration_gen	1.3.6.1.4.1.818.1.1.10.7.7.5			The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)
upsControl_gen	1.3.6.1.4.1.818.1.1.10.8
INT upsShutdownType_gen	1.3.6.1.4.1.818.1.1.10.8.1	INTEGER	read-write	This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)
I32 upsShutdownAfterDelay_gen	1.3.6.1.4.1.818.1.1.10.8.2	Integer32	read-write	Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)
I32 upsStartupAfterDelay_gen	1.3.6.1.4.1.818.1.1.10.8.3	Integer32	read-write	Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)
I32 upsRebootWithDuration_gen	1.3.6.1.4.1.818.1.1.10.8.4	Integer32	read-write	Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)
INT upsAutoRestart_gen	1.3.6.1.4.1.818.1.1.10.8.5	INTEGER	read-write	Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)
NUM upsReceptaclesNum_gen	1.3.6.1.4.1.818.1.1.10.8.6	NonNegativeInteger32	read-only	The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.
upsReceptacleTable_gen	1.3.6.1.4.1.818.1.1.10.8.7		not-accessible	A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.
upsReceptacleEntry_gen	1.3.6.1.4.1.818.1.1.10.8.7.1		not-accessible	An entry containing information applicable to a particular receptacle.
NUM upsReceptacleLineIndex_gen	1.3.6.1.4.1.818.1.1.10.8.7.1.1	PositiveInteger32	not-accessible	The receptacle line identifier.
INT upsReceptacleOnOff_gen	1.3.6.1.4.1.818.1.1.10.8.7.1.2	INTEGER	read-write	The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.
INT upsUPSMode_gen	1.3.6.1.4.1.818.1.1.10.8.8	INTEGER	read-write	The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)
INT upsRectifierOnOff_gen	1.3.6.1.4.1.818.1.1.10.8.9	INTEGER	read-write	The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.
INT upsBatteryChargeMethod_gen	1.3.6.1.4.1.818.1.1.10.8.10	INTEGER	read-write	The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.
INT upsInverterOnOff_gen	1.3.6.1.4.1.818.1.1.10.8.11	INTEGER	read-write	The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.
INT upsBypassOnOff_gen	1.3.6.1.4.1.818.1.1.10.8.12	INTEGER	read-write	The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.
INT upsLoadSource_gen	1.3.6.1.4.1.818.1.1.10.8.13	INTEGER	read-write	The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.
upsConfig_gen	1.3.6.1.4.1.818.1.1.10.9
NUM upsConfigInputVoltage_gen	1.3.6.1.4.1.818.1.1.10.9.1	NonNegativeInteger32	read-write	The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigInputFreq_gen	1.3.6.1.4.1.818.1.1.10.9.2	NonNegativeInteger32	read-write	The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVoltage_gen	1.3.6.1.4.1.818.1.1.10.9.3	NonNegativeInteger32	read-write	The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputFreq_gen	1.3.6.1.4.1.818.1.1.10.9.4	NonNegativeInteger32	read-write	The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVA_gen	1.3.6.1.4.1.818.1.1.10.9.5	NonNegativeInteger32	read-only	The magnitude of the nominal Volt-Amp rating.(*)
NUM upsConfigOutputPower_gen	1.3.6.1.4.1.818.1.1.10.9.6	NonNegativeInteger32	read-only	The magnitude of the nominal true power rating.(*)
NUM upsConfigLowBattTime_gen	1.3.6.1.4.1.818.1.1.10.9.7	NonNegativeInteger32	read-write	The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)
INT upsConfigAudibleStatus_gen	1.3.6.1.4.1.818.1.1.10.9.8	INTEGER	read-write	The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)
NUM upsConfigLowVoltageTransferPoint_gen	1.3.6.1.4.1.818.1.1.10.9.9	NonNegativeInteger32	read-write	The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigHighVoltageTransferPoint_gen	1.3.6.1.4.1.818.1.1.10.9.10	NonNegativeInteger32	read-write	The maximum line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigBatteryCapacity_gen	1.3.6.1.4.1.818.1.1.10.9.11	NonNegativeInteger32	read-write	The installed battery capacity. This value is the 'factory'-value, not the value after calibration.
NUM upsConfigBatteryChargeCurrent_gen	1.3.6.1.4.1.818.1.1.10.9.12	NonNegativeInteger32	read-write	The maximum battery charge current, including external chargers.
INT upsConfigNoLoadShutdown_gen	1.3.6.1.4.1.818.1.1.10.9.13	INTEGER	read-write	Dis- or enable 'no load' shutdown from the contact interface.
NUM upsConfigStartDelay_gen	1.3.6.1.4.1.818.1.1.10.9.14	PositiveInteger32	read-write	Minimum required autonomy time before the UPS may perform an autorestart.
upsGetSet_gen	1.3.6.1.4.1.818.1.1.10.10
NUM upsEventGetNext_gen	1.3.6.1.4.1.818.1.1.10.10.1	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.
NUM upsEventGetPrevious_gen	1.3.6.1.4.1.818.1.1.10.10.2	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMP-NOSUCHNAME for UPSs that don't support this command.
NUM upsEventSetStartingTimeStamp_gen	1.3.6.1.4.1.818.1.1.10.10.3	NonNegativeInteger32	read-write	The timestamp which is used as starting point for downloading events from the UPS event buffer
NUM upsEventRetreiveCurrentTimeStamp_gen	1.3.6.1.4.1.818.1.1.10.10.4	NonNegativeInteger32	read-only	The current timestamp is retreived from the UPS
NUM upsEventTableSize_gen	1.3.6.1.4.1.818.1.1.10.10.5	NonNegativeInteger32	read-only	The number of entries in the event table. This object indicates the number of rows in the event table.
upsEventTable_gen	1.3.6.1.4.1.818.1.1.10.10.6		not-accessible	A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.
upsEventEntry_gen	1.3.6.1.4.1.818.1.1.10.10.6.1		not-accessible	An entry containing information applicable to a particular event.
NUM upsEventLineIndex_gen	1.3.6.1.4.1.818.1.1.10.10.6.1.1	PositiveInteger32	not-accessible	The event line identifier.
NUM upsEventCode_gen	1.3.6.1.4.1.818.1.1.10.10.6.1.2	NonNegativeInteger32	read-only	The event code in numerical format.
NUM upsEventStatus_gen	1.3.6.1.4.1.818.1.1.10.10.6.1.3	NonNegativeInteger32	read-only	The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMP-NOSUCHNAME is returned.
NUM upsEventTime_gen	1.3.6.1.4.1.818.1.1.10.10.6.1.4	NonNegativeInteger32	read-only	The timestamp of the moment the event was generated.
NUM upsParametersRead_gen	1.3.6.1.4.1.818.1.1.10.10.7	PositiveInteger32	read-write	The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.
NUM upsParametersWrite_gen	1.3.6.1.4.1.818.1.1.10.10.8	PositiveInteger32	read-write	The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the first value of the table with the lowest index number.
NUM upsParametersStartAddress_gen	1.3.6.1.4.1.818.1.1.10.10.9	NonNegativeInteger32	read-write	The address which is used as starting point for downloading parameters from the UPS
NUM upsParameterTableSize_gen	1.3.6.1.4.1.818.1.1.10.10.10	NonNegativeInteger32	read-only	The number of entries in the parameter table. This object indicates the number of rows in the parameter table.
upsParameterTable_gen	1.3.6.1.4.1.818.1.1.10.10.11		not-accessible	A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite
upsParameterEntry_gen	1.3.6.1.4.1.818.1.1.10.10.11.1		not-accessible	An entry containing information applicable to a particular parameter.
NUM upsParameterLineIndex_gen	1.3.6.1.4.1.818.1.1.10.10.11.1.1	PositiveInteger32	not-accessible	The parameter line identifier.
I32 upsParameterValue_gen	1.3.6.1.4.1.818.1.1.10.10.11.1.2	Integer32	read-write	The parameter value in numerical format.
NUM upsStatus_gen	1.3.6.1.4.1.818.1.1.10.10.12	NonNegativeInteger32	read-only	The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMP-NOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0001h upsStatusEcomodeIsOn 2 0002h upsStatusBatteryIsCharging 4 0004h upsStatusBatteryIsDischarging 8 0008h upsStatusAlarmIsActive 16 0010h upsStatusRectifierIsOn 32 0020h upsStatusLowBattery 64 0040h upsStatusOnBypass 128 0080h upsStatusMainsBypassOK 256 0100h upsStatusMainsRectifierOK 512 0200h upsStatusDetourIsOn 1024 0400h upsStatusAcousticAlarmIsOn 2048 0800h - (not used.) 4096 1000h upsStatusInverterIsOn 8192 2000h upsStatusNotInParallel (Q1 open) 16384 4000h upsStatusResetLoadOff 32768 8000h upsStatusLoadOff
NUM upsMainsStatisticsMBfail_gen	1.3.6.1.4.1.818.1.1.10.10.13	NonNegativeInteger32	read-only	Count of main bypass failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsMRfail_gen	1.3.6.1.4.1.818.1.1.10.10.14	NonNegativeInteger32	read-only	Count of mains rectifier failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsB2_gen	1.3.6.1.4.1.818.1.1.10.10.15	NonNegativeInteger32	read-only	Count of transients on the mains bypass (0..2 ms), during the last 7 days.
NUM upsMainsStatisticsB5_gen	1.3.6.1.4.1.818.1.1.10.10.16	NonNegativeInteger32	read-only	Count of transients on the mains bypass (2..5 ms), during the last 7 days.
NUM upsMainsStatisticsB10_gen	1.3.6.1.4.1.818.1.1.10.10.17	NonNegativeInteger32	read-only	Count of transients on the mains bypass (5..10 ms), during the last 7 days.
NUM upsMainsStatisticsB200_gen	1.3.6.1.4.1.818.1.1.10.10.18	NonNegativeInteger32	read-only	Count of transients on the mains bypass (10..200 ms), during the last 7 days.
NUM upsMainsStatisticsBypRel_gen	1.3.6.1.4.1.818.1.1.10.10.19	NonNegativeInteger32	read-only	Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.
NUM upsTime_gen	1.3.6.1.4.1.818.1.1.10.10.20	NonNegativeInteger32	read-write	The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMP-genERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.
STR upsRequestPermission_gen	1.3.6.1.4.1.818.1.1.10.10.21	DisplayString	write-only	An encrypted code is send to enable use of restricted write objects during a limited period of time.
I32 upsEventGetCode_gen	1.3.6.1.4.1.818.1.1.10.10.22	Integer32	write-only	The code which is used as starting point to downloading the events from the UPS event buffer.
TES upsEventSpinLock_gen	1.3.6.1.4.1.818.1.1.10.10.23	TestAndIncr	read-write	A spin lock on the event subsystem.
TES upsParameterSpinLock_gen	1.3.6.1.4.1.818.1.1.10.10.24	TestAndIncr	read-write	A spin lock on the parameters subsystem.
geUPSTraps_gen	1.3.6.1.4.1.818.1.1.10.11
NTF upsAlarmBatteryBadTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.1			One or more batteries have been determined to require replacement.
NTF upsAlarmOnBatteryTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.2			An On Battery condition is restored.
NTF upsAlarmLowBatteryTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.
NTF upsAlarmDepletedBatteryTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.4			The UPS will be unable to sustain the present load when and if the utility power is lost)
NTF upsAlarmTempBadTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.5			A temperature is out of tolerance.
NTF upsAlarmInputBadTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.6			An input condition is out of tolerance.
NTF upsAlarmOutputBadTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.7			An output condition (other than OutputOverload) is out of tolerance.
NTF upsAlarmOutputOverloadTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.8			The output load exceeds the UPS output capacity.
NTF upsAlarmOnBypassTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.9			The Bypass is presently engaged on the UPS.
NTF upsAlarmBypassBadTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.10			The Bypass is out of tolerance.
NTF upsAlarmOutputOffAsRequestedTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.11			The UPS has shutdown as requested, i.e., the output is off.
NTF upsAlarmUpsOffAsRequestedTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.12			The entire UPS has shutdown as commanded.
NTF upsAlarmChargerFailedTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.13			An uncorrected problem has been detected within the UPS charger subsystem.
NTF upsAlarmUpsOutputOffTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.14			The output of the UPS is in the off state.
NTF upsAlarmUpsSystemOffTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.15			The UPS system is in the off state.
NTF upsAlarmFanFailureTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.16			The failure of one or more fans in the UPS has been detected.
NTF upsAlarmFuseFailureTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.17			The failure of one or more fuses has been detected.
NTF upsAlarmGeneralFaultTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.18			A general fault in the UPS has been detected.
NTF upsAlarmDiagnosticTestFailedTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.19			The result of the last diagnostic test indicates a failure.
NTF upsAlarmCommunicationsLostTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.20			A problem has been encountered in the communication between the agent and the UPS.
NTF upsAlarmAwaitingPowerTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.21			The UPS output is off and the UPS is awaiting the return of the input power (*).
NTF upsAlarmShutdownPendingTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.22			A upsShutdownAfterDelay countdown is underway.
NTF upsAlarmShutdownImminentTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
NTF upsAlarmTestInProgressTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.
NTF upsAlarmReceptacleOffTrap_gen	1.3.6.1.4.1.818.1.1.10.11.0.25			A receptacle has been switched off.
NTF upsAlarmBatteryBadRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.33			A Battery bad condition is restored.
NTF upsAlarmOnBatteryRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.34			The UPS is drawing power from mains again.
NTF upsAlarmLowBatteryRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.35			A Low Battery condition is restored.
NTF upsAlarmDepletedBatteryRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.36			A Depleted Battery condition is restored.
NTF upsAlarmTempBadRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.37			A bad temperature condition is restored.
NTF upsAlarmInputBadRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.38			An input bad condition is restored.
NTF upsAlarmOutputBadRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.39			An output bad condition is restored.
NTF upsAlarmOutputOverloadRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.40			An output overload condition is restored.
NTF upsAlarmOnBypassRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.41			An On Bypass condition is restored.
NTF upsAlarmBypassBadRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.42			A Bypass bad condition is restored.
NTF upsAlarmOutputOffAsRequestedRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.43			A request shutdown has been restored.
NTF upsAlarmUpsOffAsRequestedRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.44			A entire UPS command has been restored.
NTF upsAlarmChargerFailedRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.45			A Charger Failer condition is restored.
NTF upsAlarmUpsOutputOn_gen	1.3.6.1.4.1.818.1.1.10.11.0.46			The output of the UPS switched in the on state.
NTF upsAlarmUpsSystemOn_gen	1.3.6.1.4.1.818.1.1.10.11.0.47			The UPS system is switched in the on state.
NTF upsAlarmFanFailureRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.48			A Fan failure condition is restored.
NTF upsAlarmFuseFailureRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.49			A Fuse failure condition is restored.
NTF upsAlarmGeneralFaultRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.50			A general fault is restored.
NTF upsAlarmDiagnosticTestFailedRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.51			A last diagnostic test indicates a failure is restored.
NTF upsAlarmCommunicationsLostRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.52			A problem in the communication between the agent and the UPS is restored.
NTF upsAlarmAwaitingPowerRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.53			A awaiting power condition is restored (*).
NTF upsAlarmShutdownPendingRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.54			A upsShutdownAfterDelay countdown is restored.
NTF upsAlarmShutdownImminentRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.55			A shutdown imminent condition is restored.
NTF upsAlarmTestInProgressRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.56			The test is in progress is terminated.
NTF upsAlarmReceptacleOn_gen	1.3.6.1.4.1.818.1.1.10.11.0.57			A receptacle has been switched on.
NTF upsAlarmValueLow_gen	1.3.6.1.4.1.818.1.1.10.11.0.129			A measurement value reached a value below its low-level threshold.
NTF upsAlarmValueHigh_gen	1.3.6.1.4.1.818.1.1.10.11.0.130			A measurement value reached a value higher than its high-level threshold.
NTF upsAlarmValueLowRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.133			A ValueLow alarm condition is restored.
NTF upsAlarmValueHighRestored_gen	1.3.6.1.4.1.818.1.1.10.11.0.134			A ValueHigh alarm condition is restored.
geFirstUPS	1.3.6.1.4.1.818.1.1.11
upsIdent_first	1.3.6.1.4.1.818.1.1.11.1
STR upsIdentManufacturer_first	1.3.6.1.4.1.818.1.1.11.1.1	DisplayString	read-only	The name of the UPS manufacturer.(*)
STR upsIdentModel_first	1.3.6.1.4.1.818.1.1.11.1.2	DisplayString	read-only	The UPS Model designation.(*)
STR upsIdentUPSSoftwareVersion_first	1.3.6.1.4.1.818.1.1.11.1.3	DisplayString	read-only	The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)
STR upsIdentAgentSoftwareVersion_first	1.3.6.1.4.1.818.1.1.11.1.4	DisplayString	read-only	The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)
STR upsIdentName_first	1.3.6.1.4.1.818.1.1.11.1.5	DisplayString	read-write	A string identifying the UPS. This object should be set by the administrator.(*)
STR upsIdentAttachedDevices_first	1.3.6.1.4.1.818.1.1.11.1.6	DisplayString	read-write	A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)
STR upsIdentUPSSerialNumber_first	1.3.6.1.4.1.818.1.1.11.1.7	DisplayString	read-only	The UPS serial number
STR upsIdentComProtVersion_first	1.3.6.1.4.1.818.1.1.11.1.8	DisplayString	read-only	The IMV communication protocol version
NUM upsIdentOperatingTime_first	1.3.6.1.4.1.818.1.1.11.1.9	NonNegativeInteger32	read-only	The present value of the operating time. total 'on' time since UPS manufactured
upsBattery_first	1.3.6.1.4.1.818.1.1.11.2
INT upsBatteryStatus_first	1.3.6.1.4.1.818.1.1.11.2.1	INTEGER	read-only	The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)
NUM upsSecondsOnBattery_first	1.3.6.1.4.1.818.1.1.11.2.2	NonNegativeInteger32	read-only	If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)
NUM upsEstimatedMinutesRemaining_first	1.3.6.1.4.1.818.1.1.11.2.3	PositiveInteger32	read-only	An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)
I32 upsEstimatedChargeRemaining_first	1.3.6.1.4.1.818.1.1.11.2.4	Integer32	read-only	An estimate of the battery charge remaining expressed as a percent of full charge.(*)
NUM upsBatteryVoltage_first	1.3.6.1.4.1.818.1.1.11.2.5	NonNegativeInteger32	read-only	The magnitude of the present battery voltage.(*)
I32 upsBatteryCurrent_first	1.3.6.1.4.1.818.1.1.11.2.6	Integer32	read-only	The present battery current.(*)
I32 upsBatteryTemperature_first	1.3.6.1.4.1.818.1.1.11.2.7	Integer32	read-only	The ambient temperature at or near the UPS Battery casing.(*)
upsInput_first	1.3.6.1.4.1.818.1.1.11.3
C32 upsInputLineBads_first	1.3.6.1.4.1.818.1.1.11.3.1	Counter32	read-only	A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)
NUM upsInputNumLines_first	1.3.6.1.4.1.818.1.1.11.3.2	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)
upsInputTable_first	1.3.6.1.4.1.818.1.1.11.3.3		not-accessible	A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)
upsInputEntry_first	1.3.6.1.4.1.818.1.1.11.3.3.1		not-accessible	An entry containing information applicable to a particular input line.(*)
NUM upsInputLineIndex_first	1.3.6.1.4.1.818.1.1.11.3.3.1.1	PositiveInteger32	not-accessible	The input line identifier.(*)
NUM upsInputFrequency_first	1.3.6.1.4.1.818.1.1.11.3.3.1.2	NonNegativeInteger32	read-only	The present input frequency.(*)
NUM upsInputVoltage_first	1.3.6.1.4.1.818.1.1.11.3.3.1.3	NonNegativeInteger32	read-only	The magnitude of the present input voltage.(*)
NUM upsInputCurrent_first	1.3.6.1.4.1.818.1.1.11.3.3.1.4	NonNegativeInteger32	read-only	The magnitude of the present input current.(*)
NUM upsInputTruePower_first	1.3.6.1.4.1.818.1.1.11.3.3.1.5	NonNegativeInteger32	read-only	The magnitude of the present input true power.(*)
NUM upsInputVoltageMin_first	1.3.6.1.4.1.818.1.1.11.3.3.1.6	NonNegativeInteger32	read-only	The lowest magnitude of the input voltage since last read out.
NUM upsInputVoltageMax_first	1.3.6.1.4.1.818.1.1.11.3.3.1.7	NonNegativeInteger32	read-only	The highest magnitude of the input voltage since last read out.
upsOutput_first	1.3.6.1.4.1.818.1.1.11.4
INT upsOutputSource_first	1.3.6.1.4.1.818.1.1.11.4.1	INTEGER	read-only	The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)
NUM upsOutputFrequency_first	1.3.6.1.4.1.818.1.1.11.4.2	NonNegativeInteger32	read-only	The present output frequency.(*)
NUM upsOutputNumLines_first	1.3.6.1.4.1.818.1.1.11.4.3	NonNegativeInteger32	read-only	The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)
upsOutputTable_first	1.3.6.1.4.1.818.1.1.11.4.4		not-accessible	A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)
upsOutputEntry_first	1.3.6.1.4.1.818.1.1.11.4.4.1		not-accessible	An entry containing information applicable to a particular output line.(*)
NUM upsOutputLineIndex_first	1.3.6.1.4.1.818.1.1.11.4.4.1.1	PositiveInteger32	not-accessible	The output line identifier.(*)
NUM upsOutputVoltage_first	1.3.6.1.4.1.818.1.1.11.4.4.1.2	NonNegativeInteger32	read-only	The present output voltage.(*)
NUM upsOutputCurrent_first	1.3.6.1.4.1.818.1.1.11.4.4.1.3	NonNegativeInteger32	read-only	The present output current.(*)
NUM upsOutputPower_first	1.3.6.1.4.1.818.1.1.11.4.4.1.4	NonNegativeInteger32	read-only	The present output true power.(*)
I32 upsOutputPercentLoad_first	1.3.6.1.4.1.818.1.1.11.4.4.1.5	Integer32	read-only	The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)
upsBypass_first	1.3.6.1.4.1.818.1.1.11.5
NUM upsBypassFrequency_first	1.3.6.1.4.1.818.1.1.11.5.1	NonNegativeInteger32	read-only	The present bypass frequency.(*)
NUM upsBypassNumLines_first	1.3.6.1.4.1.818.1.1.11.5.2	NonNegativeInteger32	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)
upsBypassTable_first	1.3.6.1.4.1.818.1.1.11.5.3		not-accessible	A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)
upsBypassEntry_first	1.3.6.1.4.1.818.1.1.11.5.3.1		not-accessible	An entry containing information applicable to a particular bypass input.(*)
NUM upsBypassLineIndex_first	1.3.6.1.4.1.818.1.1.11.5.3.1.1	PositiveInteger32	not-accessible	The bypass line identifier.(*)
NUM upsBypassVoltage_first	1.3.6.1.4.1.818.1.1.11.5.3.1.2	NonNegativeInteger32	read-only	The present bypass voltage.(*)
NUM upsBypassCurrent_first	1.3.6.1.4.1.818.1.1.11.5.3.1.3	NonNegativeInteger32	read-only	The present bypass current.(*)
NUM upsBypassPower_first	1.3.6.1.4.1.818.1.1.11.5.3.1.4	NonNegativeInteger32	read-only	The present true power conveyed by the bypass.(*)
upsAlarm_first	1.3.6.1.4.1.818.1.1.11.6
G32 upsAlarmsPresent_first	1.3.6.1.4.1.818.1.1.11.6.1	Gauge32	read-only	The present number of active alarm conditions.(*)
upsAlarmTable_first	1.3.6.1.4.1.818.1.1.11.6.2		not-accessible	A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)
upsAlarmEntry_first	1.3.6.1.4.1.818.1.1.11.6.2.1		not-accessible	An entry containing information applicable to a particular alarm.(*)
NUM upsAlarmId_first	1.3.6.1.4.1.818.1.1.11.6.2.1.1	PositiveInteger32	not-accessible	A unique identifier for an alarm condition. This value must remain constant.(*)
OID upsAlarmDescr_first	1.3.6.1.4.1.818.1.1.11.6.2.1.2	AutonomousType	read-only	A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)
TIM upsAlarmTime_first	1.3.6.1.4.1.818.1.1.11.6.2.1.3	TimeStamp	read-only	The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)
upsWellKnownAlarms_first	1.3.6.1.4.1.818.1.1.11.6.3
upsAlarmBatteryBad_first	1.3.6.1.4.1.818.1.1.11.6.3.1			One or more batteries have been determined to require replacement.(*)
upsAlarmOnBattery_first	1.3.6.1.4.1.818.1.1.11.6.3.2			The UPS is drawing power from the batteries.(*)
upsAlarmLowBattery_first	1.3.6.1.4.1.818.1.1.11.6.3.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)
upsAlarmDepletedBattery_first	1.3.6.1.4.1.818.1.1.11.6.3.4			The UPS will be unable to sustain the present load when and if the utility power is lost.(*)
upsAlarmTempBad_first	1.3.6.1.4.1.818.1.1.11.6.3.5			A temperature is out of tolerance.(*)
upsAlarmInputBad_first	1.3.6.1.4.1.818.1.1.11.6.3.6			An input condition is out of tolerance.(*)
upsAlarmOutputBad_first	1.3.6.1.4.1.818.1.1.11.6.3.7			An output condition (other than OutputOverload) is out of tolerance.(*)
upsAlarmOutputOverload_first	1.3.6.1.4.1.818.1.1.11.6.3.8			The output load exceeds the UPS output capacity.(*)
upsAlarmOnBypass_first	1.3.6.1.4.1.818.1.1.11.6.3.9			The Bypass is presently engaged on the UPS.(*)
upsAlarmBypassBad_first	1.3.6.1.4.1.818.1.1.11.6.3.10			The Bypass is out of tolerance.(*)
upsAlarmOutputOffAsRequested_first	1.3.6.1.4.1.818.1.1.11.6.3.11			The UPS has shutdown as requested, i.e., the output is off.(*)
upsAlarmUpsOffAsRequested_first	1.3.6.1.4.1.818.1.1.11.6.3.12			The entire UPS has shutdown as commanded.(*)
upsAlarmChargerFailed_first	1.3.6.1.4.1.818.1.1.11.6.3.13			An uncorrected problem has been detected within the UPS charger subsystem.(*)
upsAlarmUpsOutputOff_first	1.3.6.1.4.1.818.1.1.11.6.3.14			The output of the UPS is in the off state.(*)
upsAlarmUpsSystemOff_first	1.3.6.1.4.1.818.1.1.11.6.3.15			The UPS system is in the off state.(*)
upsAlarmFanFailure_first	1.3.6.1.4.1.818.1.1.11.6.3.16			The failure of one or more fans in the UPS has been detected.(*)
upsAlarmFuseFailure_first	1.3.6.1.4.1.818.1.1.11.6.3.17			The failure of one or more fuses has been detected.(*)
upsAlarmGeneralFault_first	1.3.6.1.4.1.818.1.1.11.6.3.18			A general fault in the UPS has been detected.(*)
upsAlarmDiagnosticTestFailed_first	1.3.6.1.4.1.818.1.1.11.6.3.19			The result of the last diagnostic test indicates a failure.(*)
upsAlarmCommunicationsLost_first	1.3.6.1.4.1.818.1.1.11.6.3.20			A problem has been encountered in the communications between the agent and the UPS.(*)
upsAlarmAwaitingPower_first	1.3.6.1.4.1.818.1.1.11.6.3.21			The UPS output is off and the UPS is awaiting the return of input power.(*)
upsAlarmShutdownPending_first	1.3.6.1.4.1.818.1.1.11.6.3.22			A upsShutdownAfterDelay countdown is underway.(*)
upsAlarmShutdownImminent_first	1.3.6.1.4.1.818.1.1.11.6.3.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)
upsAlarmTestInProgress_first	1.3.6.1.4.1.818.1.1.11.6.3.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)
upsAlarmReceptacleOff_first	1.3.6.1.4.1.818.1.1.11.6.3.25			The receptacle are switch off
NUM upsAlarmMaskA_first	1.3.6.1.4.1.818.1.1.11.6.4	NonNegativeInteger32	read-only	Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.
upsTest_first	1.3.6.1.4.1.818.1.1.11.7
OID upsTestId_first	1.3.6.1.4.1.818.1.1.11.7.1	OBJECT IDENTIFIER	read-write	The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)
TES upsTestSpinLock_first	1.3.6.1.4.1.818.1.1.11.7.2	TestAndIncr	read-write	A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: try-again: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager / short delay get (upsTestSpinLock) } lock-value = upsTestSpinLock / no test in progress, start the test / set (upsTestSpinLock = lock-value, upsTestId = requested-test) if (error-index == 1) { / (upsTestSpinLock failed) / / if problem is not access control, then some other manager slipped in ahead of us / goto try-again } if (error-index == 2) { / (upsTestId) / / cannot perform the test / give up } / test started ok / / wait for test completion by polling upsTestResultsSummary / get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } / when test completes, retrieve any additional test results / / if upsTestSpinLock == lock-value + 1, then these are our test / / results (as opposed to another manager's / The initial value of upsTestSpinLock at agent initialization shall be 1.()
INT upsTestResultsSummary_first	1.3.6.1.4.1.818.1.1.11.7.3	INTEGER	read-only	The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)
STR upsTestResultsDetail_first	1.3.6.1.4.1.818.1.1.11.7.4	DisplayString	read-only	Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)
TIM upsTestStartTime_first	1.3.6.1.4.1.818.1.1.11.7.5	TimeStamp	read-only	The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)
NUM upsTestElapsedTime_first	1.3.6.1.4.1.818.1.1.11.7.6	TimeInterval	read-only	The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)
upsWellKnownTests_first	1.3.6.1.4.1.818.1.1.11.7.7
upsTestNoTestsInitiated_first	1.3.6.1.4.1.818.1.1.11.7.7.1			No tests have been initiated and no test is in progress.(*)
upsTestAbortTestInProgress_first	1.3.6.1.4.1.818.1.1.11.7.7.2			The test in progress is to be aborted / the test in progress was aborted.(*)
upsTestGeneralSystemsTest_first	1.3.6.1.4.1.818.1.1.11.7.7.3			The manufacturer's standard test of UPS device systems.(*)
upsTestQuickBatteryTest_first	1.3.6.1.4.1.818.1.1.11.7.7.4			A test that is sufficient to determine if the battery needs replacement.(*)
upsTestDeepBatteryCalibration_first	1.3.6.1.4.1.818.1.1.11.7.7.5			The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)
upsControl_first	1.3.6.1.4.1.818.1.1.11.8
INT upsShutdownType_first	1.3.6.1.4.1.818.1.1.11.8.1	INTEGER	read-write	This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)
I32 upsShutdownAfterDelay_first	1.3.6.1.4.1.818.1.1.11.8.2	Integer32	read-write	Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)
I32 upsStartupAfterDelay_first	1.3.6.1.4.1.818.1.1.11.8.3	Integer32	read-write	Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)
I32 upsRebootWithDuration_first	1.3.6.1.4.1.818.1.1.11.8.4	Integer32	read-write	Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)
INT upsAutoRestart_first	1.3.6.1.4.1.818.1.1.11.8.5	INTEGER	read-write	Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)
NUM upsReceptaclesNum_first	1.3.6.1.4.1.818.1.1.11.8.6	NonNegativeInteger32	read-only	The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.
upsReceptacleTable_first	1.3.6.1.4.1.818.1.1.11.8.7		not-accessible	A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.
upsReceptacleEntry_first	1.3.6.1.4.1.818.1.1.11.8.7.1		not-accessible	An entry containing information applicable to a particular receptacle.
NUM upsReceptacleLineIndex_first	1.3.6.1.4.1.818.1.1.11.8.7.1.1	PositiveInteger32	not-accessible	The receptacle line identifier.
INT upsReceptacleOnOff_first	1.3.6.1.4.1.818.1.1.11.8.7.1.2	INTEGER	read-write	The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.
INT upsUPSMode_first	1.3.6.1.4.1.818.1.1.11.8.8	INTEGER	read-write	The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)
INT upsRectifierOnOff_first	1.3.6.1.4.1.818.1.1.11.8.9	INTEGER	read-write	The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.
INT upsBatteryChargeMethod_first	1.3.6.1.4.1.818.1.1.11.8.10	INTEGER	read-write	The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.
INT upsInverterOnOff_first	1.3.6.1.4.1.818.1.1.11.8.11	INTEGER	read-write	The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.
INT upsBypassOnOff_first	1.3.6.1.4.1.818.1.1.11.8.12	INTEGER	read-write	The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.
INT upsLoadSource_first	1.3.6.1.4.1.818.1.1.11.8.13	INTEGER	read-write	The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.
upsConfig_first	1.3.6.1.4.1.818.1.1.11.9
NUM upsConfigInputVoltage_first	1.3.6.1.4.1.818.1.1.11.9.1	NonNegativeInteger32	read-write	The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigInputFreq_first	1.3.6.1.4.1.818.1.1.11.9.2	NonNegativeInteger32	read-write	The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVoltage_first	1.3.6.1.4.1.818.1.1.11.9.3	NonNegativeInteger32	read-write	The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputFreq_first	1.3.6.1.4.1.818.1.1.11.9.4	NonNegativeInteger32	read-write	The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVA_first	1.3.6.1.4.1.818.1.1.11.9.5	NonNegativeInteger32	read-only	The magnitude of the nominal Volt-Amp rating.(*)
NUM upsConfigOutputPower_first	1.3.6.1.4.1.818.1.1.11.9.6	NonNegativeInteger32	read-only	The magnitude of the nominal true power rating.(*)
NUM upsConfigLowBattTime_first	1.3.6.1.4.1.818.1.1.11.9.7	NonNegativeInteger32	read-write	The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)
INT upsConfigAudibleStatus_first	1.3.6.1.4.1.818.1.1.11.9.8	INTEGER	read-write	The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)
NUM upsConfigLowVoltageTransferPoint_first	1.3.6.1.4.1.818.1.1.11.9.9	NonNegativeInteger32	read-write	The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigHighVoltageTransferPoint_first	1.3.6.1.4.1.818.1.1.11.9.10	NonNegativeInteger32	read-write	The maximum line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigBatteryCapacity_first	1.3.6.1.4.1.818.1.1.11.9.11	NonNegativeInteger32	read-write	The installed battery capacity. This value is the 'factory'-value, not the value after calibration.
NUM upsConfigBatteryChargeCurrent_first	1.3.6.1.4.1.818.1.1.11.9.12	NonNegativeInteger32	read-write	The maximum battery charge current, including external chargers.
INT upsConfigNoLoadShutdown_first	1.3.6.1.4.1.818.1.1.11.9.13	INTEGER	read-write	Dis- or enable 'no load' shutdown from the contact interface.
NUM upsConfigStartDelay_first	1.3.6.1.4.1.818.1.1.11.9.14	PositiveInteger32	read-write	Minimum required autonomy time before the UPS may perform an autorestart.
upsGetSet_first	1.3.6.1.4.1.818.1.1.11.10
NUM upsEventGetNext_first	1.3.6.1.4.1.818.1.1.11.10.1	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.
NUM upsEventGetPrevious_first	1.3.6.1.4.1.818.1.1.11.10.2	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMP-NOSUCHNAME for UPSs that don't support this command.
NUM upsEventSetStartingTimeStamp_first	1.3.6.1.4.1.818.1.1.11.10.3	NonNegativeInteger32	read-write	The timestamp which is used as starting point for downloading events from the UPS event buffer
NUM upsEventRetreiveCurrentTimeStamp_first	1.3.6.1.4.1.818.1.1.11.10.4	NonNegativeInteger32	read-only	The current timestamp is retreived from the UPS
NUM upsEventTableSize_first	1.3.6.1.4.1.818.1.1.11.10.5	NonNegativeInteger32	read-only	The number of entries in the event table. This object indicates the number of rows in the event table.
upsEventTable_first	1.3.6.1.4.1.818.1.1.11.10.6		not-accessible	A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.
upsEventEntry_first	1.3.6.1.4.1.818.1.1.11.10.6.1		not-accessible	An entry containing information applicable to a particular event.
NUM upsEventLineIndex_first	1.3.6.1.4.1.818.1.1.11.10.6.1.1	PositiveInteger32	not-accessible	The event line identifier.
NUM upsEventCode_first	1.3.6.1.4.1.818.1.1.11.10.6.1.2	NonNegativeInteger32	read-only	The event code in numerical format.
NUM upsEventStatus_first	1.3.6.1.4.1.818.1.1.11.10.6.1.3	NonNegativeInteger32	read-only	The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMP-NOSUCHNAME is returned.
NUM upsEventTime_first	1.3.6.1.4.1.818.1.1.11.10.6.1.4	NonNegativeInteger32	read-only	The timestamp of the moment the event was generated.
NUM upsParametersRead_first	1.3.6.1.4.1.818.1.1.11.10.7	PositiveInteger32	read-write	The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.
NUM upsParametersWrite_first	1.3.6.1.4.1.818.1.1.11.10.8	PositiveInteger32	read-write	The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the first value of the table with the lowest index number.
NUM upsParametersStartAddress_first	1.3.6.1.4.1.818.1.1.11.10.9	NonNegativeInteger32	read-write	The address which is used as starting point for downloading parameters from the UPS
NUM upsParameterTableSize_first	1.3.6.1.4.1.818.1.1.11.10.10	NonNegativeInteger32	read-only	The number of entries in the parameter table. This object indicates the number of rows in the parameter table.
upsParameterTable_first	1.3.6.1.4.1.818.1.1.11.10.11		not-accessible	A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite
upsParameterEntry_first	1.3.6.1.4.1.818.1.1.11.10.11.1		not-accessible	An entry containing information applicable to a particular parameter.
NUM upsParameterLineIndex_first	1.3.6.1.4.1.818.1.1.11.10.11.1.1	PositiveInteger32	not-accessible	The parameter line identifier.
I32 upsParameterValue_first	1.3.6.1.4.1.818.1.1.11.10.11.1.2	Integer32	read-write	The parameter value in numerical format.
NUM upsStatus_first	1.3.6.1.4.1.818.1.1.11.10.12	NonNegativeInteger32	read-only	The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMP-NOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0001h upsStatusEcomodeIsOn 2 0002h upsStatusBatteryIsCharging 4 0004h upsStatusBatteryIsDischarging 8 0008h upsStatusAlarmIsActive 16 0010h upsStatusRectifierIsOn 32 0020h upsStatusLowBattery 64 0040h upsStatusOnBypass 128 0080h upsStatusMainsBypassOK 256 0100h upsStatusMainsRectifierOK 512 0200h upsStatusDetourIsOn 1024 0400h upsStatusAcousticAlarmIsOn 2048 0800h - (not used.) 4096 1000h upsStatusInverterIsOn 8192 2000h upsStatusNotInParallel (Q1 open) 16384 4000h upsStatusResetLoadOff 32768 8000h upsStatusLoadOff
NUM upsMainsStatisticsMBfail_first	1.3.6.1.4.1.818.1.1.11.10.13	NonNegativeInteger32	read-only	Count of main bypass failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsMRfail_first	1.3.6.1.4.1.818.1.1.11.10.14	NonNegativeInteger32	read-only	Count of mains rectifier failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsB2_first	1.3.6.1.4.1.818.1.1.11.10.15	NonNegativeInteger32	read-only	Count of transients on the mains bypass (0..2 ms), during the last 7 days.
NUM upsMainsStatisticsB5_first	1.3.6.1.4.1.818.1.1.11.10.16	NonNegativeInteger32	read-only	Count of transients on the mains bypass (2..5 ms), during the last 7 days.
NUM upsMainsStatisticsB10_first	1.3.6.1.4.1.818.1.1.11.10.17	NonNegativeInteger32	read-only	Count of transients on the mains bypass (5..10 ms), during the last 7 days.
NUM upsMainsStatisticsB200_first	1.3.6.1.4.1.818.1.1.11.10.18	NonNegativeInteger32	read-only	Count of transients on the mains bypass (10..200 ms), during the last 7 days.
NUM upsMainsStatisticsBypRel_first	1.3.6.1.4.1.818.1.1.11.10.19	NonNegativeInteger32	read-only	Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.
NUM upsTime_first	1.3.6.1.4.1.818.1.1.11.10.20	NonNegativeInteger32	read-write	The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMP-firstERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.
STR upsRequestPermission_first	1.3.6.1.4.1.818.1.1.11.10.21	DisplayString	write-only	An encrypted code is send to enable use of restricted write objects during a limited period of time.
I32 upsEventGetCode_first	1.3.6.1.4.1.818.1.1.11.10.22	Integer32	write-only	The code which is used as starting point to downloading the events from the UPS event buffer.
TES upsEventSpinLock_first	1.3.6.1.4.1.818.1.1.11.10.23	TestAndIncr	read-write	A spin lock on the event subsystem.
TES upsParameterSpinLock_first	1.3.6.1.4.1.818.1.1.11.10.24	TestAndIncr	read-write	A spin lock on the parameters subsystem.
geUPSTraps_first	1.3.6.1.4.1.818.1.1.11.11
NTF upsAlarmBatteryBadTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.1			One or more batteries have been determined to require replacement.
NTF upsAlarmOnBatteryTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.2			An On Battery condition is restored.
NTF upsAlarmLowBatteryTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.
NTF upsAlarmDepletedBatteryTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.4			The UPS will be unable to sustain the present load when and if the utility power is lost)
NTF upsAlarmTempBadTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.5			A temperature is out of tolerance.
NTF upsAlarmInputBadTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.6			An input condition is out of tolerance.
NTF upsAlarmOutputBadTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.7			An output condition (other than OutputOverload) is out of tolerance.
NTF upsAlarmOutputOverloadTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.8			The output load exceeds the UPS output capacity.
NTF upsAlarmOnBypassTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.9			The Bypass is presently engaged on the UPS.
NTF upsAlarmBypassBadTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.10			The Bypass is out of tolerance.
NTF upsAlarmOutputOffAsRequestedTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.11			The UPS has shutdown as requested, i.e., the output is off.
NTF upsAlarmUpsOffAsRequestedTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.12			The entire UPS has shutdown as commanded.
NTF upsAlarmChargerFailedTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.13			An uncorrected problem has been detected within the UPS charger subsystem.
NTF upsAlarmUpsOutputOffTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.14			The output of the UPS is in the off state.
NTF upsAlarmUpsSystemOffTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.15			The UPS system is in the off state.
NTF upsAlarmFanFailureTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.16			The failure of one or more fans in the UPS has been detected.
NTF upsAlarmFuseFailureTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.17			The failure of one or more fuses has been detected.
NTF upsAlarmGeneralFaultTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.18			A general fault in the UPS has been detected.
NTF upsAlarmDiagnosticTestFailedTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.19			The result of the last diagnostic test indicates a failure.
NTF upsAlarmCommunicationsLostTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.20			A problem has been encountered in the communication between the agent and the UPS.
NTF upsAlarmAwaitingPowerTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.21			The UPS output is off and the UPS is awaiting the return of the input power (*).
NTF upsAlarmShutdownPendingTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.22			A upsShutdownAfterDelay countdown is underway.
NTF upsAlarmShutdownImminentTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
NTF upsAlarmTestInProgressTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.
NTF upsAlarmReceptacleOffTrap_first	1.3.6.1.4.1.818.1.1.11.11.0.25			A receptacle has been switched off.
NTF upsAlarmBatteryBadRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.33			A Battery bad condition is restored.
NTF upsAlarmOnBatteryRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.34			The UPS is drawing power from mains again.
NTF upsAlarmLowBatteryRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.35			A Low Battery condition is restored.
NTF upsAlarmDepletedBatteryRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.36			A Depleted Battery condition is restored.
NTF upsAlarmTempBadRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.37			A bad temperature condition is restored.
NTF upsAlarmInputBadRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.38			An input bad condition is restored.
NTF upsAlarmOutputBadRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.39			An output bad condition is restored.
NTF upsAlarmOutputOverloadRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.40			An output overload condition is restored.
NTF upsAlarmOnBypassRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.41			An On Bypass condition is restored.
NTF upsAlarmBypassBadRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.42			A Bypass bad condition is restored.
NTF upsAlarmOutputOffAsRequestedRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.43			A request shutdown has been restored.
NTF upsAlarmUpsOffAsRequestedRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.44			A entire UPS command has been restored.
NTF upsAlarmChargerFailedRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.45			A Charger Failer condition is restored.
NTF upsAlarmUpsOutputOn_first	1.3.6.1.4.1.818.1.1.11.11.0.46			The output of the UPS switched in the on state.
NTF upsAlarmUpsSystemOn_first	1.3.6.1.4.1.818.1.1.11.11.0.47			The UPS system is switched in the on state.
NTF upsAlarmFanFailureRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.48			A Fan failure condition is restored.
NTF upsAlarmFuseFailureRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.49			A Fuse failure condition is restored.
NTF upsAlarmGeneralFaultRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.50			A general fault is restored.
NTF upsAlarmDiagnosticTestFailedRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.51			A last diagnostic test indicates a failure is restored.
NTF upsAlarmCommunicationsLostRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.52			A problem in the communication between the agent and the UPS is restored.
NTF upsAlarmAwaitingPowerRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.53			A awaiting power condition is restored (*).
NTF upsAlarmShutdownPendingRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.54			A upsShutdownAfterDelay countdown is restored.
NTF upsAlarmShutdownImminentRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.55			A shutdown imminent condition is restored.
NTF upsAlarmTestInProgressRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.56			The test is in progress is terminated.
NTF upsAlarmReceptacleOn_first	1.3.6.1.4.1.818.1.1.11.11.0.57			A receptacle has been switched on.
NTF upsAlarmValueLow_first	1.3.6.1.4.1.818.1.1.11.11.0.129			A measurement value reached a value below its low-level threshold.
NTF upsAlarmValueHigh_first	1.3.6.1.4.1.818.1.1.11.11.0.130			A measurement value reached a value higher than its high-level threshold.
NTF upsAlarmValueLowRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.133			A ValueLow alarm condition is restored.
NTF upsAlarmValueHighRestored_first	1.3.6.1.4.1.818.1.1.11.11.0.134			A ValueHigh alarm condition is restored.
geSecondUPS	1.3.6.1.4.1.818.1.1.12
upsIdent_second	1.3.6.1.4.1.818.1.1.12.1
STR upsIdentManufacturer_second	1.3.6.1.4.1.818.1.1.12.1.1	DisplayString	read-only	The name of the UPS manufacturer.(*)
STR upsIdentModel_second	1.3.6.1.4.1.818.1.1.12.1.2	DisplayString	read-only	The UPS Model designation.(*)
STR upsIdentUPSSoftwareVersion_second	1.3.6.1.4.1.818.1.1.12.1.3	DisplayString	read-only	The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)
STR upsIdentAgentSoftwareVersion_second	1.3.6.1.4.1.818.1.1.12.1.4	DisplayString	read-only	The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)
STR upsIdentName_second	1.3.6.1.4.1.818.1.1.12.1.5	DisplayString	read-write	A string identifying the UPS. This object should be set by the administrator.(*)
STR upsIdentAttachedDevices_second	1.3.6.1.4.1.818.1.1.12.1.6	DisplayString	read-write	A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)
STR upsIdentUPSSerialNumber_second	1.3.6.1.4.1.818.1.1.12.1.7	DisplayString	read-only	The UPS serial number
STR upsIdentComProtVersion_second	1.3.6.1.4.1.818.1.1.12.1.8	DisplayString	read-only	The IMV communication protocol version
NUM upsIdentOperatingTime_second	1.3.6.1.4.1.818.1.1.12.1.9	NonNegativeInteger32	read-only	The present value of the operating time. total 'on' time since UPS manufactured
upsBattery_second	1.3.6.1.4.1.818.1.1.12.2
INT upsBatteryStatus_second	1.3.6.1.4.1.818.1.1.12.2.1	INTEGER	read-only	The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)
NUM upsSecondsOnBattery_second	1.3.6.1.4.1.818.1.1.12.2.2	NonNegativeInteger32	read-only	If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)
NUM upsEstimatedMinutesRemaining_second	1.3.6.1.4.1.818.1.1.12.2.3	PositiveInteger32	read-only	An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)
I32 upsEstimatedChargeRemaining_second	1.3.6.1.4.1.818.1.1.12.2.4	Integer32	read-only	An estimate of the battery charge remaining expressed as a percent of full charge.(*)
NUM upsBatteryVoltage_second	1.3.6.1.4.1.818.1.1.12.2.5	NonNegativeInteger32	read-only	The magnitude of the present battery voltage.(*)
I32 upsBatteryCurrent_second	1.3.6.1.4.1.818.1.1.12.2.6	Integer32	read-only	The present battery current.(*)
I32 upsBatteryTemperature_second	1.3.6.1.4.1.818.1.1.12.2.7	Integer32	read-only	The ambient temperature at or near the UPS Battery casing.(*)
upsInput_second	1.3.6.1.4.1.818.1.1.12.3
C32 upsInputLineBads_second	1.3.6.1.4.1.818.1.1.12.3.1	Counter32	read-only	A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)
NUM upsInputNumLines_second	1.3.6.1.4.1.818.1.1.12.3.2	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)
upsInputTable_second	1.3.6.1.4.1.818.1.1.12.3.3		not-accessible	A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)
upsInputEntry_second	1.3.6.1.4.1.818.1.1.12.3.3.1		not-accessible	An entry containing information applicable to a particular input line.(*)
NUM upsInputLineIndex_second	1.3.6.1.4.1.818.1.1.12.3.3.1.1	PositiveInteger32	not-accessible	The input line identifier.(*)
NUM upsInputFrequency_second	1.3.6.1.4.1.818.1.1.12.3.3.1.2	NonNegativeInteger32	read-only	The present input frequency.(*)
NUM upsInputVoltage_second	1.3.6.1.4.1.818.1.1.12.3.3.1.3	NonNegativeInteger32	read-only	The magnitude of the present input voltage.(*)
NUM upsInputCurrent_second	1.3.6.1.4.1.818.1.1.12.3.3.1.4	NonNegativeInteger32	read-only	The magnitude of the present input current.(*)
NUM upsInputTruePower_second	1.3.6.1.4.1.818.1.1.12.3.3.1.5	NonNegativeInteger32	read-only	The magnitude of the present input true power.(*)
NUM upsInputVoltageMin_second	1.3.6.1.4.1.818.1.1.12.3.3.1.6	NonNegativeInteger32	read-only	The lowest magnitude of the input voltage since last read out.
NUM upsInputVoltageMax_second	1.3.6.1.4.1.818.1.1.12.3.3.1.7	NonNegativeInteger32	read-only	The highest magnitude of the input voltage since last read out.
upsOutput_second	1.3.6.1.4.1.818.1.1.12.4
INT upsOutputSource_second	1.3.6.1.4.1.818.1.1.12.4.1	INTEGER	read-only	The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)
NUM upsOutputFrequency_second	1.3.6.1.4.1.818.1.1.12.4.2	NonNegativeInteger32	read-only	The present output frequency.(*)
NUM upsOutputNumLines_second	1.3.6.1.4.1.818.1.1.12.4.3	NonNegativeInteger32	read-only	The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)
upsOutputTable_second	1.3.6.1.4.1.818.1.1.12.4.4		not-accessible	A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)
upsOutputEntry_second	1.3.6.1.4.1.818.1.1.12.4.4.1		not-accessible	An entry containing information applicable to a particular output line.(*)
NUM upsOutputLineIndex_second	1.3.6.1.4.1.818.1.1.12.4.4.1.1	PositiveInteger32	not-accessible	The output line identifier.(*)
NUM upsOutputVoltage_second	1.3.6.1.4.1.818.1.1.12.4.4.1.2	NonNegativeInteger32	read-only	The present output voltage.(*)
NUM upsOutputCurrent_second	1.3.6.1.4.1.818.1.1.12.4.4.1.3	NonNegativeInteger32	read-only	The present output current.(*)
NUM upsOutputPower_second	1.3.6.1.4.1.818.1.1.12.4.4.1.4	NonNegativeInteger32	read-only	The present output true power.(*)
I32 upsOutputPercentLoad_second	1.3.6.1.4.1.818.1.1.12.4.4.1.5	Integer32	read-only	The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)
upsBypass_second	1.3.6.1.4.1.818.1.1.12.5
NUM upsBypassFrequency_second	1.3.6.1.4.1.818.1.1.12.5.1	NonNegativeInteger32	read-only	The present bypass frequency.(*)
NUM upsBypassNumLines_second	1.3.6.1.4.1.818.1.1.12.5.2	NonNegativeInteger32	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)
upsBypassTable_second	1.3.6.1.4.1.818.1.1.12.5.3		not-accessible	A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)
upsBypassEntry_second	1.3.6.1.4.1.818.1.1.12.5.3.1		not-accessible	An entry containing information applicable to a particular bypass input.(*)
NUM upsBypassLineIndex_second	1.3.6.1.4.1.818.1.1.12.5.3.1.1	PositiveInteger32	not-accessible	The bypass line identifier.(*)
NUM upsBypassVoltage_second	1.3.6.1.4.1.818.1.1.12.5.3.1.2	NonNegativeInteger32	read-only	The present bypass voltage.(*)
NUM upsBypassCurrent_second	1.3.6.1.4.1.818.1.1.12.5.3.1.3	NonNegativeInteger32	read-only	The present bypass current.(*)
NUM upsBypassPower_second	1.3.6.1.4.1.818.1.1.12.5.3.1.4	NonNegativeInteger32	read-only	The present true power conveyed by the bypass.(*)
upsAlarm_second	1.3.6.1.4.1.818.1.1.12.6
G32 upsAlarmsPresent_second	1.3.6.1.4.1.818.1.1.12.6.1	Gauge32	read-only	The present number of active alarm conditions.(*)
upsAlarmTable_second	1.3.6.1.4.1.818.1.1.12.6.2		not-accessible	A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)
upsAlarmEntry_second	1.3.6.1.4.1.818.1.1.12.6.2.1		not-accessible	An entry containing information applicable to a particular alarm.(*)
NUM upsAlarmId_second	1.3.6.1.4.1.818.1.1.12.6.2.1.1	PositiveInteger32	not-accessible	A unique identifier for an alarm condition. This value must remain constant.(*)
OID upsAlarmDescr_second	1.3.6.1.4.1.818.1.1.12.6.2.1.2	AutonomousType	read-only	A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)
TIM upsAlarmTime_second	1.3.6.1.4.1.818.1.1.12.6.2.1.3	TimeStamp	read-only	The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)
upsWellKnownAlarms_second	1.3.6.1.4.1.818.1.1.12.6.3
upsAlarmBatteryBad_second	1.3.6.1.4.1.818.1.1.12.6.3.1			One or more batteries have been determined to require replacement.(*)
upsAlarmOnBattery_second	1.3.6.1.4.1.818.1.1.12.6.3.2			The UPS is drawing power from the batteries.(*)
upsAlarmLowBattery_second	1.3.6.1.4.1.818.1.1.12.6.3.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)
upsAlarmDepletedBattery_second	1.3.6.1.4.1.818.1.1.12.6.3.4			The UPS will be unable to sustain the present load when and if the utility power is lost.(*)
upsAlarmTempBad_second	1.3.6.1.4.1.818.1.1.12.6.3.5			A temperature is out of tolerance.(*)
upsAlarmInputBad_second	1.3.6.1.4.1.818.1.1.12.6.3.6			An input condition is out of tolerance.(*)
upsAlarmOutputBad_second	1.3.6.1.4.1.818.1.1.12.6.3.7			An output condition (other than OutputOverload) is out of tolerance.(*)
upsAlarmOutputOverload_second	1.3.6.1.4.1.818.1.1.12.6.3.8			The output load exceeds the UPS output capacity.(*)
upsAlarmOnBypass_second	1.3.6.1.4.1.818.1.1.12.6.3.9			The Bypass is presently engaged on the UPS.(*)
upsAlarmBypassBad_second	1.3.6.1.4.1.818.1.1.12.6.3.10			The Bypass is out of tolerance.(*)
upsAlarmOutputOffAsRequested_second	1.3.6.1.4.1.818.1.1.12.6.3.11			The UPS has shutdown as requested, i.e., the output is off.(*)
upsAlarmUpsOffAsRequested_second	1.3.6.1.4.1.818.1.1.12.6.3.12			The entire UPS has shutdown as commanded.(*)
upsAlarmChargerFailed_second	1.3.6.1.4.1.818.1.1.12.6.3.13			An uncorrected problem has been detected within the UPS charger subsystem.(*)
upsAlarmUpsOutputOff_second	1.3.6.1.4.1.818.1.1.12.6.3.14			The output of the UPS is in the off state.(*)
upsAlarmUpsSystemOff_second	1.3.6.1.4.1.818.1.1.12.6.3.15			The UPS system is in the off state.(*)
upsAlarmFanFailure_second	1.3.6.1.4.1.818.1.1.12.6.3.16			The failure of one or more fans in the UPS has been detected.(*)
upsAlarmFuseFailure_second	1.3.6.1.4.1.818.1.1.12.6.3.17			The failure of one or more fuses has been detected.(*)
upsAlarmGeneralFault_second	1.3.6.1.4.1.818.1.1.12.6.3.18			A general fault in the UPS has been detected.(*)
upsAlarmDiagnosticTestFailed_second	1.3.6.1.4.1.818.1.1.12.6.3.19			The result of the last diagnostic test indicates a failure.(*)
upsAlarmCommunicationsLost_second	1.3.6.1.4.1.818.1.1.12.6.3.20			A problem has been encountered in the communications between the agent and the UPS.(*)
upsAlarmAwaitingPower_second	1.3.6.1.4.1.818.1.1.12.6.3.21			The UPS output is off and the UPS is awaiting the return of input power.(*)
upsAlarmShutdownPending_second	1.3.6.1.4.1.818.1.1.12.6.3.22			A upsShutdownAfterDelay countdown is underway.(*)
upsAlarmShutdownImminent_second	1.3.6.1.4.1.818.1.1.12.6.3.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)
upsAlarmTestInProgress_second	1.3.6.1.4.1.818.1.1.12.6.3.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)
upsAlarmReceptacleOff_second	1.3.6.1.4.1.818.1.1.12.6.3.25			The receptacle are switch off
NUM upsAlarmMaskA_second	1.3.6.1.4.1.818.1.1.12.6.4	NonNegativeInteger32	read-only	Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.
upsTest_second	1.3.6.1.4.1.818.1.1.12.7
OID upsTestId_second	1.3.6.1.4.1.818.1.1.12.7.1	OBJECT IDENTIFIER	read-write	The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)
TES upsTestSpinLock_second	1.3.6.1.4.1.818.1.1.12.7.2	TestAndIncr	read-write	A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: try-again: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager / short delay get (upsTestSpinLock) } lock-value = upsTestSpinLock / no test in progress, start the test / set (upsTestSpinLock = lock-value, upsTestId = requested-test) if (error-index == 1) { / (upsTestSpinLock failed) / / if problem is not access control, then some other manager slipped in ahead of us / goto try-again } if (error-index == 2) { / (upsTestId) / / cannot perform the test / give up } / test started ok / / wait for test completion by polling upsTestResultsSummary / get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } / when test completes, retrieve any additional test results / / if upsTestSpinLock == lock-value + 1, then these are our test / / results (as opposed to another manager's / The initial value of upsTestSpinLock at agent initialization shall be 1.()
INT upsTestResultsSummary_second	1.3.6.1.4.1.818.1.1.12.7.3	INTEGER	read-only	The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)
STR upsTestResultsDetail_second	1.3.6.1.4.1.818.1.1.12.7.4	DisplayString	read-only	Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)
TIM upsTestStartTime_second	1.3.6.1.4.1.818.1.1.12.7.5	TimeStamp	read-only	The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)
NUM upsTestElapsedTime_second	1.3.6.1.4.1.818.1.1.12.7.6	TimeInterval	read-only	The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)
upsWellKnownTests_second	1.3.6.1.4.1.818.1.1.12.7.7
upsTestNoTestsInitiated_second	1.3.6.1.4.1.818.1.1.12.7.7.1			No tests have been initiated and no test is in progress.(*)
upsTestAbortTestInProgress_second	1.3.6.1.4.1.818.1.1.12.7.7.2			The test in progress is to be aborted / the test in progress was aborted.(*)
upsTestGeneralSystemsTest_second	1.3.6.1.4.1.818.1.1.12.7.7.3			The manufacturer's standard test of UPS device systems.(*)
upsTestQuickBatteryTest_second	1.3.6.1.4.1.818.1.1.12.7.7.4			A test that is sufficient to determine if the battery needs replacement.(*)
upsTestDeepBatteryCalibration_second	1.3.6.1.4.1.818.1.1.12.7.7.5			The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)
upsControl_second	1.3.6.1.4.1.818.1.1.12.8
INT upsShutdownType_second	1.3.6.1.4.1.818.1.1.12.8.1	INTEGER	read-write	This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)
I32 upsShutdownAfterDelay_second	1.3.6.1.4.1.818.1.1.12.8.2	Integer32	read-write	Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)
I32 upsStartupAfterDelay_second	1.3.6.1.4.1.818.1.1.12.8.3	Integer32	read-write	Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)
I32 upsRebootWithDuration_second	1.3.6.1.4.1.818.1.1.12.8.4	Integer32	read-write	Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)
INT upsAutoRestart_second	1.3.6.1.4.1.818.1.1.12.8.5	INTEGER	read-write	Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)
NUM upsReceptaclesNum_second	1.3.6.1.4.1.818.1.1.12.8.6	NonNegativeInteger32	read-only	The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.
upsReceptacleTable_second	1.3.6.1.4.1.818.1.1.12.8.7		not-accessible	A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.
upsReceptacleEntry_second	1.3.6.1.4.1.818.1.1.12.8.7.1		not-accessible	An entry containing information applicable to a particular receptacle.
NUM upsReceptacleLineIndex_second	1.3.6.1.4.1.818.1.1.12.8.7.1.1	PositiveInteger32	not-accessible	The receptacle line identifier.
INT upsReceptacleOnOff_second	1.3.6.1.4.1.818.1.1.12.8.7.1.2	INTEGER	read-write	The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.
INT upsUPSMode_second	1.3.6.1.4.1.818.1.1.12.8.8	INTEGER	read-write	The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)
INT upsRectifierOnOff_second	1.3.6.1.4.1.818.1.1.12.8.9	INTEGER	read-write	The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.
INT upsBatteryChargeMethod_second	1.3.6.1.4.1.818.1.1.12.8.10	INTEGER	read-write	The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.
INT upsInverterOnOff_second	1.3.6.1.4.1.818.1.1.12.8.11	INTEGER	read-write	The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.
INT upsBypassOnOff_second	1.3.6.1.4.1.818.1.1.12.8.12	INTEGER	read-write	The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.
INT upsLoadSource_second	1.3.6.1.4.1.818.1.1.12.8.13	INTEGER	read-write	The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.
upsConfig_second	1.3.6.1.4.1.818.1.1.12.9
NUM upsConfigInputVoltage_second	1.3.6.1.4.1.818.1.1.12.9.1	NonNegativeInteger32	read-write	The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigInputFreq_second	1.3.6.1.4.1.818.1.1.12.9.2	NonNegativeInteger32	read-write	The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVoltage_second	1.3.6.1.4.1.818.1.1.12.9.3	NonNegativeInteger32	read-write	The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputFreq_second	1.3.6.1.4.1.818.1.1.12.9.4	NonNegativeInteger32	read-write	The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVA_second	1.3.6.1.4.1.818.1.1.12.9.5	NonNegativeInteger32	read-only	The magnitude of the nominal Volt-Amp rating.(*)
NUM upsConfigOutputPower_second	1.3.6.1.4.1.818.1.1.12.9.6	NonNegativeInteger32	read-only	The magnitude of the nominal true power rating.(*)
NUM upsConfigLowBattTime_second	1.3.6.1.4.1.818.1.1.12.9.7	NonNegativeInteger32	read-write	The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)
INT upsConfigAudibleStatus_second	1.3.6.1.4.1.818.1.1.12.9.8	INTEGER	read-write	The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)
NUM upsConfigLowVoltageTransferPoint_second	1.3.6.1.4.1.818.1.1.12.9.9	NonNegativeInteger32	read-write	The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigHighVoltageTransferPoint_second	1.3.6.1.4.1.818.1.1.12.9.10	NonNegativeInteger32	read-write	The maximum line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigBatteryCapacity_second	1.3.6.1.4.1.818.1.1.12.9.11	NonNegativeInteger32	read-write	The installed battery capacity. This value is the 'factory'-value, not the value after calibration.
NUM upsConfigBatteryChargeCurrent_second	1.3.6.1.4.1.818.1.1.12.9.12	NonNegativeInteger32	read-write	The maximum battery charge current, including external chargers.
INT upsConfigNoLoadShutdown_second	1.3.6.1.4.1.818.1.1.12.9.13	INTEGER	read-write	Dis- or enable 'no load' shutdown from the contact interface.
NUM upsConfigStartDelay_second	1.3.6.1.4.1.818.1.1.12.9.14	PositiveInteger32	read-write	Minimum required autonomy time before the UPS may perform an autorestart.
upsGetSet_second	1.3.6.1.4.1.818.1.1.12.10
NUM upsEventGetNext_second	1.3.6.1.4.1.818.1.1.12.10.1	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.
NUM upsEventGetPrevious_second	1.3.6.1.4.1.818.1.1.12.10.2	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMP-NOSUCHNAME for UPSs that don't support this command.
NUM upsEventSetStartingTimeStamp_second	1.3.6.1.4.1.818.1.1.12.10.3	NonNegativeInteger32	read-write	The timestamp which is used as starting point for downloading events from the UPS event buffer
NUM upsEventRetreiveCurrentTimeStamp_second	1.3.6.1.4.1.818.1.1.12.10.4	NonNegativeInteger32	read-only	The current timestamp is retreived from the UPS
NUM upsEventTableSize_second	1.3.6.1.4.1.818.1.1.12.10.5	NonNegativeInteger32	read-only	The number of entries in the event table. This object indicates the number of rows in the event table.
upsEventTable_second	1.3.6.1.4.1.818.1.1.12.10.6		not-accessible	A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.
upsEventEntry_second	1.3.6.1.4.1.818.1.1.12.10.6.1		not-accessible	An entry containing information applicable to a particular event.
NUM upsEventLineIndex_second	1.3.6.1.4.1.818.1.1.12.10.6.1.1	PositiveInteger32	not-accessible	The event line identifier.
NUM upsEventCode_second	1.3.6.1.4.1.818.1.1.12.10.6.1.2	NonNegativeInteger32	read-only	The event code in numerical format.
NUM upsEventStatus_second	1.3.6.1.4.1.818.1.1.12.10.6.1.3	NonNegativeInteger32	read-only	The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMP-NOSUCHNAME is returned.
NUM upsEventTime_second	1.3.6.1.4.1.818.1.1.12.10.6.1.4	NonNegativeInteger32	read-only	The timestamp of the moment the event was generated.
NUM upsParametersRead_second	1.3.6.1.4.1.818.1.1.12.10.7	PositiveInteger32	read-write	The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.
NUM upsParametersWrite_second	1.3.6.1.4.1.818.1.1.12.10.8	PositiveInteger32	read-write	The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the first value of the table with the lowest index number.
NUM upsParametersStartAddress_second	1.3.6.1.4.1.818.1.1.12.10.9	NonNegativeInteger32	read-write	The address which is used as starting point for downloading parameters from the UPS
NUM upsParameterTableSize_second	1.3.6.1.4.1.818.1.1.12.10.10	NonNegativeInteger32	read-only	The number of entries in the parameter table. This object indicates the number of rows in the parameter table.
upsParameterTable_second	1.3.6.1.4.1.818.1.1.12.10.11		not-accessible	A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite
upsParameterEntry_second	1.3.6.1.4.1.818.1.1.12.10.11.1		not-accessible	An entry containing information applicable to a particular parameter.
NUM upsParameterLineIndex_second	1.3.6.1.4.1.818.1.1.12.10.11.1.1	PositiveInteger32	not-accessible	The parameter line identifier.
I32 upsParameterValue_second	1.3.6.1.4.1.818.1.1.12.10.11.1.2	Integer32	read-write	The parameter value in numerical format.
NUM upsStatus_second	1.3.6.1.4.1.818.1.1.12.10.12	NonNegativeInteger32	read-only	The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMP-NOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0001h upsStatusEcomodeIsOn 2 0002h upsStatusBatteryIsCharging 4 0004h upsStatusBatteryIsDischarging 8 0008h upsStatusAlarmIsActive 16 0010h upsStatusRectifierIsOn 32 0020h upsStatusLowBattery 64 0040h upsStatusOnBypass 128 0080h upsStatusMainsBypassOK 256 0100h upsStatusMainsRectifierOK 512 0200h upsStatusDetourIsOn 1024 0400h upsStatusAcousticAlarmIsOn 2048 0800h - (not used.) 4096 1000h upsStatusInverterIsOn 8192 2000h upsStatusNotInParallel (Q1 open) 16384 4000h upsStatusResetLoadOff 32768 8000h upsStatusLoadOff
NUM upsMainsStatisticsMBfail_second	1.3.6.1.4.1.818.1.1.12.10.13	NonNegativeInteger32	read-only	Count of main bypass failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsMRfail_second	1.3.6.1.4.1.818.1.1.12.10.14	NonNegativeInteger32	read-only	Count of mains rectifier failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsB2_second	1.3.6.1.4.1.818.1.1.12.10.15	NonNegativeInteger32	read-only	Count of transients on the mains bypass (0..2 ms), during the last 7 days.
NUM upsMainsStatisticsB5_second	1.3.6.1.4.1.818.1.1.12.10.16	NonNegativeInteger32	read-only	Count of transients on the mains bypass (2..5 ms), during the last 7 days.
NUM upsMainsStatisticsB10_second	1.3.6.1.4.1.818.1.1.12.10.17	NonNegativeInteger32	read-only	Count of transients on the mains bypass (5..10 ms), during the last 7 days.
NUM upsMainsStatisticsB200_second	1.3.6.1.4.1.818.1.1.12.10.18	NonNegativeInteger32	read-only	Count of transients on the mains bypass (10..200 ms), during the last 7 days.
NUM upsMainsStatisticsBypRel_second	1.3.6.1.4.1.818.1.1.12.10.19	NonNegativeInteger32	read-only	Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.
NUM upsTime_second	1.3.6.1.4.1.818.1.1.12.10.20	NonNegativeInteger32	read-write	The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMP-secondERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.
STR upsRequestPermission_second	1.3.6.1.4.1.818.1.1.12.10.21	DisplayString	write-only	An encrypted code is send to enable use of restricted write objects during a limited period of time.
I32 upsEventGetCode_second	1.3.6.1.4.1.818.1.1.12.10.22	Integer32	write-only	The code which is used as starting point to downloading the events from the UPS event buffer.
TES upsEventSpinLock_second	1.3.6.1.4.1.818.1.1.12.10.23	TestAndIncr	read-write	A spin lock on the event subsystem.
TES upsParameterSpinLock_second	1.3.6.1.4.1.818.1.1.12.10.24	TestAndIncr	read-write	A spin lock on the parameters subsystem.
geUPSTraps_second	1.3.6.1.4.1.818.1.1.12.11
NTF upsAlarmBatteryBadTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.1			One or more batteries have been determined to require replacement.
NTF upsAlarmOnBatteryTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.2			An On Battery condition is restored.
NTF upsAlarmLowBatteryTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.
NTF upsAlarmDepletedBatteryTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.4			The UPS will be unable to sustain the present load when and if the utility power is lost)
NTF upsAlarmTempBadTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.5			A temperature is out of tolerance.
NTF upsAlarmInputBadTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.6			An input condition is out of tolerance.
NTF upsAlarmOutputBadTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.7			An output condition (other than OutputOverload) is out of tolerance.
NTF upsAlarmOutputOverloadTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.8			The output load exceeds the UPS output capacity.
NTF upsAlarmOnBypassTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.9			The Bypass is presently engaged on the UPS.
NTF upsAlarmBypassBadTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.10			The Bypass is out of tolerance.
NTF upsAlarmOutputOffAsRequestedTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.11			The UPS has shutdown as requested, i.e., the output is off.
NTF upsAlarmUpsOffAsRequestedTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.12			The entire UPS has shutdown as commanded.
NTF upsAlarmChargerFailedTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.13			An uncorrected problem has been detected within the UPS charger subsystem.
NTF upsAlarmUpsOutputOffTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.14			The output of the UPS is in the off state.
NTF upsAlarmUpsSystemOffTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.15			The UPS system is in the off state.
NTF upsAlarmFanFailureTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.16			The failure of one or more fans in the UPS has been detected.
NTF upsAlarmFuseFailureTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.17			The failure of one or more fuses has been detected.
NTF upsAlarmGeneralFaultTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.18			A general fault in the UPS has been detected.
NTF upsAlarmDiagnosticTestFailedTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.19			The result of the last diagnostic test indicates a failure.
NTF upsAlarmCommunicationsLostTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.20			A problem has been encountered in the communication between the agent and the UPS.
NTF upsAlarmAwaitingPowerTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.21			The UPS output is off and the UPS is awaiting the return of the input power (*).
NTF upsAlarmShutdownPendingTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.22			A upsShutdownAfterDelay countdown is underway.
NTF upsAlarmShutdownImminentTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
NTF upsAlarmTestInProgressTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.
NTF upsAlarmReceptacleOffTrap_second	1.3.6.1.4.1.818.1.1.12.11.0.25			A receptacle has been switched off.
NTF upsAlarmBatteryBadRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.33			A Battery bad condition is restored.
NTF upsAlarmOnBatteryRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.34			The UPS is drawing power from mains again.
NTF upsAlarmLowBatteryRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.35			A Low Battery condition is restored.
NTF upsAlarmDepletedBatteryRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.36			A Depleted Battery condition is restored.
NTF upsAlarmTempBadRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.37			A bad temperature condition is restored.
NTF upsAlarmInputBadRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.38			An input bad condition is restored.
NTF upsAlarmOutputBadRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.39			An output bad condition is restored.
NTF upsAlarmOutputOverloadRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.40			An output overload condition is restored.
NTF upsAlarmOnBypassRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.41			An On Bypass condition is restored.
NTF upsAlarmBypassBadRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.42			A Bypass bad condition is restored.
NTF upsAlarmOutputOffAsRequestedRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.43			A request shutdown has been restored.
NTF upsAlarmUpsOffAsRequestedRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.44			A entire UPS command has been restored.
NTF upsAlarmChargerFailedRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.45			A Charger Failer condition is restored.
NTF upsAlarmUpsOutputOn_second	1.3.6.1.4.1.818.1.1.12.11.0.46			The output of the UPS switched in the on state.
NTF upsAlarmUpsSystemOn_second	1.3.6.1.4.1.818.1.1.12.11.0.47			The UPS system is switched in the on state.
NTF upsAlarmFanFailureRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.48			A Fan failure condition is restored.
NTF upsAlarmFuseFailureRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.49			A Fuse failure condition is restored.
NTF upsAlarmGeneralFaultRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.50			A general fault is restored.
NTF upsAlarmDiagnosticTestFailedRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.51			A last diagnostic test indicates a failure is restored.
NTF upsAlarmCommunicationsLostRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.52			A problem in the communication between the agent and the UPS is restored.
NTF upsAlarmAwaitingPowerRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.53			A awaiting power condition is restored (*).
NTF upsAlarmShutdownPendingRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.54			A upsShutdownAfterDelay countdown is restored.
NTF upsAlarmShutdownImminentRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.55			A shutdown imminent condition is restored.
NTF upsAlarmTestInProgressRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.56			The test is in progress is terminated.
NTF upsAlarmReceptacleOn_second	1.3.6.1.4.1.818.1.1.12.11.0.57			A receptacle has been switched on.
NTF upsAlarmValueLow_second	1.3.6.1.4.1.818.1.1.12.11.0.129			A measurement value reached a value below its low-level threshold.
NTF upsAlarmValueHigh_second	1.3.6.1.4.1.818.1.1.12.11.0.130			A measurement value reached a value higher than its high-level threshold.
NTF upsAlarmValueLowRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.133			A ValueLow alarm condition is restored.
NTF upsAlarmValueHighRestored_second	1.3.6.1.4.1.818.1.1.12.11.0.134			A ValueHigh alarm condition is restored.
geThirdUPS	1.3.6.1.4.1.818.1.1.13
upsIdent_third	1.3.6.1.4.1.818.1.1.13.1
STR upsIdentManufacturer_third	1.3.6.1.4.1.818.1.1.13.1.1	DisplayString	read-only	The name of the UPS manufacturer.(*)
STR upsIdentModel_third	1.3.6.1.4.1.818.1.1.13.1.2	DisplayString	read-only	The UPS Model designation.(*)
STR upsIdentUPSSoftwareVersion_third	1.3.6.1.4.1.818.1.1.13.1.3	DisplayString	read-only	The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)
STR upsIdentAgentSoftwareVersion_third	1.3.6.1.4.1.818.1.1.13.1.4	DisplayString	read-only	The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)
STR upsIdentName_third	1.3.6.1.4.1.818.1.1.13.1.5	DisplayString	read-write	A string identifying the UPS. This object should be set by the administrator.(*)
STR upsIdentAttachedDevices_third	1.3.6.1.4.1.818.1.1.13.1.6	DisplayString	read-write	A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)
STR upsIdentUPSSerialNumber_third	1.3.6.1.4.1.818.1.1.13.1.7	DisplayString	read-only	The UPS serial number
STR upsIdentComProtVersion_third	1.3.6.1.4.1.818.1.1.13.1.8	DisplayString	read-only	The IMV communication protocol version
NUM upsIdentOperatingTime_third	1.3.6.1.4.1.818.1.1.13.1.9	NonNegativeInteger32	read-only	The present value of the operating time. total 'on' time since UPS manufactured
upsBattery_third	1.3.6.1.4.1.818.1.1.13.2
INT upsBatteryStatus_third	1.3.6.1.4.1.818.1.1.13.2.1	INTEGER	read-only	The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)
NUM upsSecondsOnBattery_third	1.3.6.1.4.1.818.1.1.13.2.2	NonNegativeInteger32	read-only	If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)
NUM upsEstimatedMinutesRemaining_third	1.3.6.1.4.1.818.1.1.13.2.3	PositiveInteger32	read-only	An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)
I32 upsEstimatedChargeRemaining_third	1.3.6.1.4.1.818.1.1.13.2.4	Integer32	read-only	An estimate of the battery charge remaining expressed as a percent of full charge.(*)
NUM upsBatteryVoltage_third	1.3.6.1.4.1.818.1.1.13.2.5	NonNegativeInteger32	read-only	The magnitude of the present battery voltage.(*)
I32 upsBatteryCurrent_third	1.3.6.1.4.1.818.1.1.13.2.6	Integer32	read-only	The present battery current.(*)
I32 upsBatteryTemperature_third	1.3.6.1.4.1.818.1.1.13.2.7	Integer32	read-only	The ambient temperature at or near the UPS Battery casing.(*)
upsInput_third	1.3.6.1.4.1.818.1.1.13.3
C32 upsInputLineBads_third	1.3.6.1.4.1.818.1.1.13.3.1	Counter32	read-only	A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)
NUM upsInputNumLines_third	1.3.6.1.4.1.818.1.1.13.3.2	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)
upsInputTable_third	1.3.6.1.4.1.818.1.1.13.3.3		not-accessible	A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)
upsInputEntry_third	1.3.6.1.4.1.818.1.1.13.3.3.1		not-accessible	An entry containing information applicable to a particular input line.(*)
NUM upsInputLineIndex_third	1.3.6.1.4.1.818.1.1.13.3.3.1.1	PositiveInteger32	not-accessible	The input line identifier.(*)
NUM upsInputFrequency_third	1.3.6.1.4.1.818.1.1.13.3.3.1.2	NonNegativeInteger32	read-only	The present input frequency.(*)
NUM upsInputVoltage_third	1.3.6.1.4.1.818.1.1.13.3.3.1.3	NonNegativeInteger32	read-only	The magnitude of the present input voltage.(*)
NUM upsInputCurrent_third	1.3.6.1.4.1.818.1.1.13.3.3.1.4	NonNegativeInteger32	read-only	The magnitude of the present input current.(*)
NUM upsInputTruePower_third	1.3.6.1.4.1.818.1.1.13.3.3.1.5	NonNegativeInteger32	read-only	The magnitude of the present input true power.(*)
NUM upsInputVoltageMin_third	1.3.6.1.4.1.818.1.1.13.3.3.1.6	NonNegativeInteger32	read-only	The lowest magnitude of the input voltage since last read out.
NUM upsInputVoltageMax_third	1.3.6.1.4.1.818.1.1.13.3.3.1.7	NonNegativeInteger32	read-only	The highest magnitude of the input voltage since last read out.
upsOutput_third	1.3.6.1.4.1.818.1.1.13.4
INT upsOutputSource_third	1.3.6.1.4.1.818.1.1.13.4.1	INTEGER	read-only	The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)
NUM upsOutputFrequency_third	1.3.6.1.4.1.818.1.1.13.4.2	NonNegativeInteger32	read-only	The present output frequency.(*)
NUM upsOutputNumLines_third	1.3.6.1.4.1.818.1.1.13.4.3	NonNegativeInteger32	read-only	The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)
upsOutputTable_third	1.3.6.1.4.1.818.1.1.13.4.4		not-accessible	A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)
upsOutputEntry_third	1.3.6.1.4.1.818.1.1.13.4.4.1		not-accessible	An entry containing information applicable to a particular output line.(*)
NUM upsOutputLineIndex_third	1.3.6.1.4.1.818.1.1.13.4.4.1.1	PositiveInteger32	not-accessible	The output line identifier.(*)
NUM upsOutputVoltage_third	1.3.6.1.4.1.818.1.1.13.4.4.1.2	NonNegativeInteger32	read-only	The present output voltage.(*)
NUM upsOutputCurrent_third	1.3.6.1.4.1.818.1.1.13.4.4.1.3	NonNegativeInteger32	read-only	The present output current.(*)
NUM upsOutputPower_third	1.3.6.1.4.1.818.1.1.13.4.4.1.4	NonNegativeInteger32	read-only	The present output true power.(*)
I32 upsOutputPercentLoad_third	1.3.6.1.4.1.818.1.1.13.4.4.1.5	Integer32	read-only	The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)
upsBypass_third	1.3.6.1.4.1.818.1.1.13.5
NUM upsBypassFrequency_third	1.3.6.1.4.1.818.1.1.13.5.1	NonNegativeInteger32	read-only	The present bypass frequency.(*)
NUM upsBypassNumLines_third	1.3.6.1.4.1.818.1.1.13.5.2	NonNegativeInteger32	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)
upsBypassTable_third	1.3.6.1.4.1.818.1.1.13.5.3		not-accessible	A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)
upsBypassEntry_third	1.3.6.1.4.1.818.1.1.13.5.3.1		not-accessible	An entry containing information applicable to a particular bypass input.(*)
NUM upsBypassLineIndex_third	1.3.6.1.4.1.818.1.1.13.5.3.1.1	PositiveInteger32	not-accessible	The bypass line identifier.(*)
NUM upsBypassVoltage_third	1.3.6.1.4.1.818.1.1.13.5.3.1.2	NonNegativeInteger32	read-only	The present bypass voltage.(*)
NUM upsBypassCurrent_third	1.3.6.1.4.1.818.1.1.13.5.3.1.3	NonNegativeInteger32	read-only	The present bypass current.(*)
NUM upsBypassPower_third	1.3.6.1.4.1.818.1.1.13.5.3.1.4	NonNegativeInteger32	read-only	The present true power conveyed by the bypass.(*)
upsAlarm_third	1.3.6.1.4.1.818.1.1.13.6
G32 upsAlarmsPresent_third	1.3.6.1.4.1.818.1.1.13.6.1	Gauge32	read-only	The present number of active alarm conditions.(*)
upsAlarmTable_third	1.3.6.1.4.1.818.1.1.13.6.2		not-accessible	A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)
upsAlarmEntry_third	1.3.6.1.4.1.818.1.1.13.6.2.1		not-accessible	An entry containing information applicable to a particular alarm.(*)
NUM upsAlarmId_third	1.3.6.1.4.1.818.1.1.13.6.2.1.1	PositiveInteger32	not-accessible	A unique identifier for an alarm condition. This value must remain constant.(*)
OID upsAlarmDescr_third	1.3.6.1.4.1.818.1.1.13.6.2.1.2	AutonomousType	read-only	A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)
TIM upsAlarmTime_third	1.3.6.1.4.1.818.1.1.13.6.2.1.3	TimeStamp	read-only	The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)
upsWellKnownAlarms_third	1.3.6.1.4.1.818.1.1.13.6.3
upsAlarmBatteryBad_third	1.3.6.1.4.1.818.1.1.13.6.3.1			One or more batteries have been determined to require replacement.(*)
upsAlarmOnBattery_third	1.3.6.1.4.1.818.1.1.13.6.3.2			The UPS is drawing power from the batteries.(*)
upsAlarmLowBattery_third	1.3.6.1.4.1.818.1.1.13.6.3.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)
upsAlarmDepletedBattery_third	1.3.6.1.4.1.818.1.1.13.6.3.4			The UPS will be unable to sustain the present load when and if the utility power is lost.(*)
upsAlarmTempBad_third	1.3.6.1.4.1.818.1.1.13.6.3.5			A temperature is out of tolerance.(*)
upsAlarmInputBad_third	1.3.6.1.4.1.818.1.1.13.6.3.6			An input condition is out of tolerance.(*)
upsAlarmOutputBad_third	1.3.6.1.4.1.818.1.1.13.6.3.7			An output condition (other than OutputOverload) is out of tolerance.(*)
upsAlarmOutputOverload_third	1.3.6.1.4.1.818.1.1.13.6.3.8			The output load exceeds the UPS output capacity.(*)
upsAlarmOnBypass_third	1.3.6.1.4.1.818.1.1.13.6.3.9			The Bypass is presently engaged on the UPS.(*)
upsAlarmBypassBad_third	1.3.6.1.4.1.818.1.1.13.6.3.10			The Bypass is out of tolerance.(*)
upsAlarmOutputOffAsRequested_third	1.3.6.1.4.1.818.1.1.13.6.3.11			The UPS has shutdown as requested, i.e., the output is off.(*)
upsAlarmUpsOffAsRequested_third	1.3.6.1.4.1.818.1.1.13.6.3.12			The entire UPS has shutdown as commanded.(*)
upsAlarmChargerFailed_third	1.3.6.1.4.1.818.1.1.13.6.3.13			An uncorrected problem has been detected within the UPS charger subsystem.(*)
upsAlarmUpsOutputOff_third	1.3.6.1.4.1.818.1.1.13.6.3.14			The output of the UPS is in the off state.(*)
upsAlarmUpsSystemOff_third	1.3.6.1.4.1.818.1.1.13.6.3.15			The UPS system is in the off state.(*)
upsAlarmFanFailure_third	1.3.6.1.4.1.818.1.1.13.6.3.16			The failure of one or more fans in the UPS has been detected.(*)
upsAlarmFuseFailure_third	1.3.6.1.4.1.818.1.1.13.6.3.17			The failure of one or more fuses has been detected.(*)
upsAlarmGeneralFault_third	1.3.6.1.4.1.818.1.1.13.6.3.18			A general fault in the UPS has been detected.(*)
upsAlarmDiagnosticTestFailed_third	1.3.6.1.4.1.818.1.1.13.6.3.19			The result of the last diagnostic test indicates a failure.(*)
upsAlarmCommunicationsLost_third	1.3.6.1.4.1.818.1.1.13.6.3.20			A problem has been encountered in the communications between the agent and the UPS.(*)
upsAlarmAwaitingPower_third	1.3.6.1.4.1.818.1.1.13.6.3.21			The UPS output is off and the UPS is awaiting the return of input power.(*)
upsAlarmShutdownPending_third	1.3.6.1.4.1.818.1.1.13.6.3.22			A upsShutdownAfterDelay countdown is underway.(*)
upsAlarmShutdownImminent_third	1.3.6.1.4.1.818.1.1.13.6.3.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)
upsAlarmTestInProgress_third	1.3.6.1.4.1.818.1.1.13.6.3.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)
upsAlarmReceptacleOff_third	1.3.6.1.4.1.818.1.1.13.6.3.25			The receptacle are switch off
NUM upsAlarmMaskA_third	1.3.6.1.4.1.818.1.1.13.6.4	NonNegativeInteger32	read-only	Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.
upsTest_third	1.3.6.1.4.1.818.1.1.13.7
OID upsTestId_third	1.3.6.1.4.1.818.1.1.13.7.1	OBJECT IDENTIFIER	read-write	The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)
TES upsTestSpinLock_third	1.3.6.1.4.1.818.1.1.13.7.2	TestAndIncr	read-write	A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: try-again: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager / short delay get (upsTestSpinLock) } lock-value = upsTestSpinLock / no test in progress, start the test / set (upsTestSpinLock = lock-value, upsTestId = requested-test) if (error-index == 1) { / (upsTestSpinLock failed) / / if problem is not access control, then some other manager slipped in ahead of us / goto try-again } if (error-index == 2) { / (upsTestId) / / cannot perform the test / give up } / test started ok / / wait for test completion by polling upsTestResultsSummary / get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } / when test completes, retrieve any additional test results / / if upsTestSpinLock == lock-value + 1, then these are our test / / results (as opposed to another manager's / The initial value of upsTestSpinLock at agent initialization shall be 1.()
INT upsTestResultsSummary_third	1.3.6.1.4.1.818.1.1.13.7.3	INTEGER	read-only	The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)
STR upsTestResultsDetail_third	1.3.6.1.4.1.818.1.1.13.7.4	DisplayString	read-only	Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)
TIM upsTestStartTime_third	1.3.6.1.4.1.818.1.1.13.7.5	TimeStamp	read-only	The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)
NUM upsTestElapsedTime_third	1.3.6.1.4.1.818.1.1.13.7.6	TimeInterval	read-only	The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)
upsWellKnownTests_third	1.3.6.1.4.1.818.1.1.13.7.7
upsTestNoTestsInitiated_third	1.3.6.1.4.1.818.1.1.13.7.7.1			No tests have been initiated and no test is in progress.(*)
upsTestAbortTestInProgress_third	1.3.6.1.4.1.818.1.1.13.7.7.2			The test in progress is to be aborted / the test in progress was aborted.(*)
upsTestGeneralSystemsTest_third	1.3.6.1.4.1.818.1.1.13.7.7.3			The manufacturer's standard test of UPS device systems.(*)
upsTestQuickBatteryTest_third	1.3.6.1.4.1.818.1.1.13.7.7.4			A test that is sufficient to determine if the battery needs replacement.(*)
upsTestDeepBatteryCalibration_third	1.3.6.1.4.1.818.1.1.13.7.7.5			The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)
upsControl_third	1.3.6.1.4.1.818.1.1.13.8
INT upsShutdownType_third	1.3.6.1.4.1.818.1.1.13.8.1	INTEGER	read-write	This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)
I32 upsShutdownAfterDelay_third	1.3.6.1.4.1.818.1.1.13.8.2	Integer32	read-write	Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)
I32 upsStartupAfterDelay_third	1.3.6.1.4.1.818.1.1.13.8.3	Integer32	read-write	Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)
I32 upsRebootWithDuration_third	1.3.6.1.4.1.818.1.1.13.8.4	Integer32	read-write	Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)
INT upsAutoRestart_third	1.3.6.1.4.1.818.1.1.13.8.5	INTEGER	read-write	Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)
NUM upsReceptaclesNum_third	1.3.6.1.4.1.818.1.1.13.8.6	NonNegativeInteger32	read-only	The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.
upsReceptacleTable_third	1.3.6.1.4.1.818.1.1.13.8.7		not-accessible	A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.
upsReceptacleEntry_third	1.3.6.1.4.1.818.1.1.13.8.7.1		not-accessible	An entry containing information applicable to a particular receptacle.
NUM upsReceptacleLineIndex_third	1.3.6.1.4.1.818.1.1.13.8.7.1.1	PositiveInteger32	not-accessible	The receptacle line identifier.
INT upsReceptacleOnOff_third	1.3.6.1.4.1.818.1.1.13.8.7.1.2	INTEGER	read-write	The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.
INT upsUPSMode_third	1.3.6.1.4.1.818.1.1.13.8.8	INTEGER	read-write	The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)
INT upsRectifierOnOff_third	1.3.6.1.4.1.818.1.1.13.8.9	INTEGER	read-write	The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.
INT upsBatteryChargeMethod_third	1.3.6.1.4.1.818.1.1.13.8.10	INTEGER	read-write	The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.
INT upsInverterOnOff_third	1.3.6.1.4.1.818.1.1.13.8.11	INTEGER	read-write	The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.
INT upsBypassOnOff_third	1.3.6.1.4.1.818.1.1.13.8.12	INTEGER	read-write	The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.
INT upsLoadSource_third	1.3.6.1.4.1.818.1.1.13.8.13	INTEGER	read-write	The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.
upsConfig_third	1.3.6.1.4.1.818.1.1.13.9
NUM upsConfigInputVoltage_third	1.3.6.1.4.1.818.1.1.13.9.1	NonNegativeInteger32	read-write	The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigInputFreq_third	1.3.6.1.4.1.818.1.1.13.9.2	NonNegativeInteger32	read-write	The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVoltage_third	1.3.6.1.4.1.818.1.1.13.9.3	NonNegativeInteger32	read-write	The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputFreq_third	1.3.6.1.4.1.818.1.1.13.9.4	NonNegativeInteger32	read-write	The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVA_third	1.3.6.1.4.1.818.1.1.13.9.5	NonNegativeInteger32	read-only	The magnitude of the nominal Volt-Amp rating.(*)
NUM upsConfigOutputPower_third	1.3.6.1.4.1.818.1.1.13.9.6	NonNegativeInteger32	read-only	The magnitude of the nominal true power rating.(*)
NUM upsConfigLowBattTime_third	1.3.6.1.4.1.818.1.1.13.9.7	NonNegativeInteger32	read-write	The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)
INT upsConfigAudibleStatus_third	1.3.6.1.4.1.818.1.1.13.9.8	INTEGER	read-write	The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)
NUM upsConfigLowVoltageTransferPoint_third	1.3.6.1.4.1.818.1.1.13.9.9	NonNegativeInteger32	read-write	The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigHighVoltageTransferPoint_third	1.3.6.1.4.1.818.1.1.13.9.10	NonNegativeInteger32	read-write	The maximum line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigBatteryCapacity_third	1.3.6.1.4.1.818.1.1.13.9.11	NonNegativeInteger32	read-write	The installed battery capacity. This value is the 'factory'-value, not the value after calibration.
NUM upsConfigBatteryChargeCurrent_third	1.3.6.1.4.1.818.1.1.13.9.12	NonNegativeInteger32	read-write	The maximum battery charge current, including external chargers.
INT upsConfigNoLoadShutdown_third	1.3.6.1.4.1.818.1.1.13.9.13	INTEGER	read-write	Dis- or enable 'no load' shutdown from the contact interface.
NUM upsConfigStartDelay_third	1.3.6.1.4.1.818.1.1.13.9.14	PositiveInteger32	read-write	Minimum required autonomy time before the UPS may perform an autorestart.
upsGetSet_third	1.3.6.1.4.1.818.1.1.13.10
NUM upsEventGetNext_third	1.3.6.1.4.1.818.1.1.13.10.1	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.
NUM upsEventGetPrevious_third	1.3.6.1.4.1.818.1.1.13.10.2	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMP-NOSUCHNAME for UPSs that don't support this command.
NUM upsEventSetStartingTimeStamp_third	1.3.6.1.4.1.818.1.1.13.10.3	NonNegativeInteger32	read-write	The timestamp which is used as starting point for downloading events from the UPS event buffer
NUM upsEventRetreiveCurrentTimeStamp_third	1.3.6.1.4.1.818.1.1.13.10.4	NonNegativeInteger32	read-only	The current timestamp is retreived from the UPS
NUM upsEventTableSize_third	1.3.6.1.4.1.818.1.1.13.10.5	NonNegativeInteger32	read-only	The number of entries in the event table. This object indicates the number of rows in the event table.
upsEventTable_third	1.3.6.1.4.1.818.1.1.13.10.6		not-accessible	A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.
upsEventEntry_third	1.3.6.1.4.1.818.1.1.13.10.6.1		not-accessible	An entry containing information applicable to a particular event.
NUM upsEventLineIndex_third	1.3.6.1.4.1.818.1.1.13.10.6.1.1	PositiveInteger32	not-accessible	The event line identifier.
NUM upsEventCode_third	1.3.6.1.4.1.818.1.1.13.10.6.1.2	NonNegativeInteger32	read-only	The event code in numerical format.
NUM upsEventStatus_third	1.3.6.1.4.1.818.1.1.13.10.6.1.3	NonNegativeInteger32	read-only	The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMP-NOSUCHNAME is returned.
NUM upsEventTime_third	1.3.6.1.4.1.818.1.1.13.10.6.1.4	NonNegativeInteger32	read-only	The timestamp of the moment the event was generated.
NUM upsParametersRead_third	1.3.6.1.4.1.818.1.1.13.10.7	PositiveInteger32	read-write	The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.
NUM upsParametersWrite_third	1.3.6.1.4.1.818.1.1.13.10.8	PositiveInteger32	read-write	The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the first value of the table with the lowest index number.
NUM upsParametersStartAddress_third	1.3.6.1.4.1.818.1.1.13.10.9	NonNegativeInteger32	read-write	The address which is used as starting point for downloading parameters from the UPS
NUM upsParameterTableSize_third	1.3.6.1.4.1.818.1.1.13.10.10	NonNegativeInteger32	read-only	The number of entries in the parameter table. This object indicates the number of rows in the parameter table.
upsParameterTable_third	1.3.6.1.4.1.818.1.1.13.10.11		not-accessible	A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite
upsParameterEntry_third	1.3.6.1.4.1.818.1.1.13.10.11.1		not-accessible	An entry containing information applicable to a particular parameter.
NUM upsParameterLineIndex_third	1.3.6.1.4.1.818.1.1.13.10.11.1.1	PositiveInteger32	not-accessible	The parameter line identifier.
I32 upsParameterValue_third	1.3.6.1.4.1.818.1.1.13.10.11.1.2	Integer32	read-write	The parameter value in numerical format.
NUM upsStatus_third	1.3.6.1.4.1.818.1.1.13.10.12	NonNegativeInteger32	read-only	The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMP-NOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0001h upsStatusEcomodeIsOn 2 0002h upsStatusBatteryIsCharging 4 0004h upsStatusBatteryIsDischarging 8 0008h upsStatusAlarmIsActive 16 0010h upsStatusRectifierIsOn 32 0020h upsStatusLowBattery 64 0040h upsStatusOnBypass 128 0080h upsStatusMainsBypassOK 256 0100h upsStatusMainsRectifierOK 512 0200h upsStatusDetourIsOn 1024 0400h upsStatusAcousticAlarmIsOn 2048 0800h - (not used.) 4096 1000h upsStatusInverterIsOn 8192 2000h upsStatusNotInParallel (Q1 open) 16384 4000h upsStatusResetLoadOff 32768 8000h upsStatusLoadOff
NUM upsMainsStatisticsMBfail_third	1.3.6.1.4.1.818.1.1.13.10.13	NonNegativeInteger32	read-only	Count of main bypass failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsMRfail_third	1.3.6.1.4.1.818.1.1.13.10.14	NonNegativeInteger32	read-only	Count of mains rectifier failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsB2_third	1.3.6.1.4.1.818.1.1.13.10.15	NonNegativeInteger32	read-only	Count of transients on the mains bypass (0..2 ms), during the last 7 days.
NUM upsMainsStatisticsB5_third	1.3.6.1.4.1.818.1.1.13.10.16	NonNegativeInteger32	read-only	Count of transients on the mains bypass (2..5 ms), during the last 7 days.
NUM upsMainsStatisticsB10_third	1.3.6.1.4.1.818.1.1.13.10.17	NonNegativeInteger32	read-only	Count of transients on the mains bypass (5..10 ms), during the last 7 days.
NUM upsMainsStatisticsB200_third	1.3.6.1.4.1.818.1.1.13.10.18	NonNegativeInteger32	read-only	Count of transients on the mains bypass (10..200 ms), during the last 7 days.
NUM upsMainsStatisticsBypRel_third	1.3.6.1.4.1.818.1.1.13.10.19	NonNegativeInteger32	read-only	Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.
NUM upsTime_third	1.3.6.1.4.1.818.1.1.13.10.20	NonNegativeInteger32	read-write	The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMP-thirdERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.
STR upsRequestPermission_third	1.3.6.1.4.1.818.1.1.13.10.21	DisplayString	write-only	An encrypted code is send to enable use of restricted write objects during a limited period of time.
I32 upsEventGetCode_third	1.3.6.1.4.1.818.1.1.13.10.22	Integer32	write-only	The code which is used as starting point to downloading the events from the UPS event buffer.
TES upsEventSpinLock_third	1.3.6.1.4.1.818.1.1.13.10.23	TestAndIncr	read-write	A spin lock on the event subsystem.
TES upsParameterSpinLock_third	1.3.6.1.4.1.818.1.1.13.10.24	TestAndIncr	read-write	A spin lock on the parameters subsystem.
geUPSTraps_third	1.3.6.1.4.1.818.1.1.13.11
NTF upsAlarmBatteryBadTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.1			One or more batteries have been determined to require replacement.
NTF upsAlarmOnBatteryTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.2			An On Battery condition is restored.
NTF upsAlarmLowBatteryTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.
NTF upsAlarmDepletedBatteryTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.4			The UPS will be unable to sustain the present load when and if the utility power is lost)
NTF upsAlarmTempBadTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.5			A temperature is out of tolerance.
NTF upsAlarmInputBadTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.6			An input condition is out of tolerance.
NTF upsAlarmOutputBadTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.7			An output condition (other than OutputOverload) is out of tolerance.
NTF upsAlarmOutputOverloadTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.8			The output load exceeds the UPS output capacity.
NTF upsAlarmOnBypassTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.9			The Bypass is presently engaged on the UPS.
NTF upsAlarmBypassBadTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.10			The Bypass is out of tolerance.
NTF upsAlarmOutputOffAsRequestedTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.11			The UPS has shutdown as requested, i.e., the output is off.
NTF upsAlarmUpsOffAsRequestedTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.12			The entire UPS has shutdown as commanded.
NTF upsAlarmChargerFailedTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.13			An uncorrected problem has been detected within the UPS charger subsystem.
NTF upsAlarmUpsOutputOffTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.14			The output of the UPS is in the off state.
NTF upsAlarmUpsSystemOffTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.15			The UPS system is in the off state.
NTF upsAlarmFanFailureTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.16			The failure of one or more fans in the UPS has been detected.
NTF upsAlarmFuseFailureTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.17			The failure of one or more fuses has been detected.
NTF upsAlarmGeneralFaultTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.18			A general fault in the UPS has been detected.
NTF upsAlarmDiagnosticTestFailedTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.19			The result of the last diagnostic test indicates a failure.
NTF upsAlarmCommunicationsLostTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.20			A problem has been encountered in the communication between the agent and the UPS.
NTF upsAlarmAwaitingPowerTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.21			The UPS output is off and the UPS is awaiting the return of the input power (*).
NTF upsAlarmShutdownPendingTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.22			A upsShutdownAfterDelay countdown is underway.
NTF upsAlarmShutdownImminentTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
NTF upsAlarmTestInProgressTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.
NTF upsAlarmReceptacleOffTrap_third	1.3.6.1.4.1.818.1.1.13.11.0.25			A receptacle has been switched off.
NTF upsAlarmBatteryBadRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.33			A Battery bad condition is restored.
NTF upsAlarmOnBatteryRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.34			The UPS is drawing power from mains again.
NTF upsAlarmLowBatteryRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.35			A Low Battery condition is restored.
NTF upsAlarmDepletedBatteryRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.36			A Depleted Battery condition is restored.
NTF upsAlarmTempBadRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.37			A bad temperature condition is restored.
NTF upsAlarmInputBadRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.38			An input bad condition is restored.
NTF upsAlarmOutputBadRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.39			An output bad condition is restored.
NTF upsAlarmOutputOverloadRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.40			An output overload condition is restored.
NTF upsAlarmOnBypassRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.41			An On Bypass condition is restored.
NTF upsAlarmBypassBadRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.42			A Bypass bad condition is restored.
NTF upsAlarmOutputOffAsRequestedRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.43			A request shutdown has been restored.
NTF upsAlarmUpsOffAsRequestedRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.44			A entire UPS command has been restored.
NTF upsAlarmChargerFailedRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.45			A Charger Failer condition is restored.
NTF upsAlarmUpsOutputOn_third	1.3.6.1.4.1.818.1.1.13.11.0.46			The output of the UPS switched in the on state.
NTF upsAlarmUpsSystemOn_third	1.3.6.1.4.1.818.1.1.13.11.0.47			The UPS system is switched in the on state.
NTF upsAlarmFanFailureRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.48			A Fan failure condition is restored.
NTF upsAlarmFuseFailureRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.49			A Fuse failure condition is restored.
NTF upsAlarmGeneralFaultRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.50			A general fault is restored.
NTF upsAlarmDiagnosticTestFailedRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.51			A last diagnostic test indicates a failure is restored.
NTF upsAlarmCommunicationsLostRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.52			A problem in the communication between the agent and the UPS is restored.
NTF upsAlarmAwaitingPowerRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.53			A awaiting power condition is restored (*).
NTF upsAlarmShutdownPendingRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.54			A upsShutdownAfterDelay countdown is restored.
NTF upsAlarmShutdownImminentRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.55			A shutdown imminent condition is restored.
NTF upsAlarmTestInProgressRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.56			The test is in progress is terminated.
NTF upsAlarmReceptacleOn_third	1.3.6.1.4.1.818.1.1.13.11.0.57			A receptacle has been switched on.
NTF upsAlarmValueLow_third	1.3.6.1.4.1.818.1.1.13.11.0.129			A measurement value reached a value below its low-level threshold.
NTF upsAlarmValueHigh_third	1.3.6.1.4.1.818.1.1.13.11.0.130			A measurement value reached a value higher than its high-level threshold.
NTF upsAlarmValueLowRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.133			A ValueLow alarm condition is restored.
NTF upsAlarmValueHighRestored_third	1.3.6.1.4.1.818.1.1.13.11.0.134			A ValueHigh alarm condition is restored.
geFourthUPS	1.3.6.1.4.1.818.1.1.14
upsIdent_fourth	1.3.6.1.4.1.818.1.1.14.1
STR upsIdentManufacturer_fourth	1.3.6.1.4.1.818.1.1.14.1.1	DisplayString	read-only	The name of the UPS manufacturer.(*)
STR upsIdentModel_fourth	1.3.6.1.4.1.818.1.1.14.1.2	DisplayString	read-only	The UPS Model designation.(*)
STR upsIdentUPSSoftwareVersion_fourth	1.3.6.1.4.1.818.1.1.14.1.3	DisplayString	read-only	The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)
STR upsIdentAgentSoftwareVersion_fourth	1.3.6.1.4.1.818.1.1.14.1.4	DisplayString	read-only	The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)
STR upsIdentName_fourth	1.3.6.1.4.1.818.1.1.14.1.5	DisplayString	read-write	A string identifying the UPS. This object should be set by the administrator.(*)
STR upsIdentAttachedDevices_fourth	1.3.6.1.4.1.818.1.1.14.1.6	DisplayString	read-write	A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)
STR upsIdentUPSSerialNumber_fourth	1.3.6.1.4.1.818.1.1.14.1.7	DisplayString	read-only	The UPS serial number
STR upsIdentComProtVersion_fourth	1.3.6.1.4.1.818.1.1.14.1.8	DisplayString	read-only	The IMV communication protocol version
NUM upsIdentOperatingTime_fourth	1.3.6.1.4.1.818.1.1.14.1.9	NonNegativeInteger32	read-only	The present value of the operating time. total 'on' time since UPS manufactured
upsBattery_fourth	1.3.6.1.4.1.818.1.1.14.2
INT upsBatteryStatus_fourth	1.3.6.1.4.1.818.1.1.14.2.1	INTEGER	read-only	The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)
NUM upsSecondsOnBattery_fourth	1.3.6.1.4.1.818.1.1.14.2.2	NonNegativeInteger32	read-only	If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)
NUM upsEstimatedMinutesRemaining_fourth	1.3.6.1.4.1.818.1.1.14.2.3	PositiveInteger32	read-only	An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)
I32 upsEstimatedChargeRemaining_fourth	1.3.6.1.4.1.818.1.1.14.2.4	Integer32	read-only	An estimate of the battery charge remaining expressed as a percent of full charge.(*)
NUM upsBatteryVoltage_fourth	1.3.6.1.4.1.818.1.1.14.2.5	NonNegativeInteger32	read-only	The magnitude of the present battery voltage.(*)
I32 upsBatteryCurrent_fourth	1.3.6.1.4.1.818.1.1.14.2.6	Integer32	read-only	The present battery current.(*)
I32 upsBatteryTemperature_fourth	1.3.6.1.4.1.818.1.1.14.2.7	Integer32	read-only	The ambient temperature at or near the UPS Battery casing.(*)
upsInput_fourth	1.3.6.1.4.1.818.1.1.14.3
C32 upsInputLineBads_fourth	1.3.6.1.4.1.818.1.1.14.3.1	Counter32	read-only	A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)
NUM upsInputNumLines_fourth	1.3.6.1.4.1.818.1.1.14.3.2	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)
upsInputTable_fourth	1.3.6.1.4.1.818.1.1.14.3.3		not-accessible	A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)
upsInputEntry_fourth	1.3.6.1.4.1.818.1.1.14.3.3.1		not-accessible	An entry containing information applicable to a particular input line.(*)
NUM upsInputLineIndex_fourth	1.3.6.1.4.1.818.1.1.14.3.3.1.1	PositiveInteger32	not-accessible	The input line identifier.(*)
NUM upsInputFrequency_fourth	1.3.6.1.4.1.818.1.1.14.3.3.1.2	NonNegativeInteger32	read-only	The present input frequency.(*)
NUM upsInputVoltage_fourth	1.3.6.1.4.1.818.1.1.14.3.3.1.3	NonNegativeInteger32	read-only	The magnitude of the present input voltage.(*)
NUM upsInputCurrent_fourth	1.3.6.1.4.1.818.1.1.14.3.3.1.4	NonNegativeInteger32	read-only	The magnitude of the present input current.(*)
NUM upsInputTruePower_fourth	1.3.6.1.4.1.818.1.1.14.3.3.1.5	NonNegativeInteger32	read-only	The magnitude of the present input true power.(*)
NUM upsInputVoltageMin_fourth	1.3.6.1.4.1.818.1.1.14.3.3.1.6	NonNegativeInteger32	read-only	The lowest magnitude of the input voltage since last read out.
NUM upsInputVoltageMax_fourth	1.3.6.1.4.1.818.1.1.14.3.3.1.7	NonNegativeInteger32	read-only	The highest magnitude of the input voltage since last read out.
upsOutput_fourth	1.3.6.1.4.1.818.1.1.14.4
INT upsOutputSource_fourth	1.3.6.1.4.1.818.1.1.14.4.1	INTEGER	read-only	The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)
NUM upsOutputFrequency_fourth	1.3.6.1.4.1.818.1.1.14.4.2	NonNegativeInteger32	read-only	The present output frequency.(*)
NUM upsOutputNumLines_fourth	1.3.6.1.4.1.818.1.1.14.4.3	NonNegativeInteger32	read-only	The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)
upsOutputTable_fourth	1.3.6.1.4.1.818.1.1.14.4.4		not-accessible	A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)
upsOutputEntry_fourth	1.3.6.1.4.1.818.1.1.14.4.4.1		not-accessible	An entry containing information applicable to a particular output line.(*)
NUM upsOutputLineIndex_fourth	1.3.6.1.4.1.818.1.1.14.4.4.1.1	PositiveInteger32	not-accessible	The output line identifier.(*)
NUM upsOutputVoltage_fourth	1.3.6.1.4.1.818.1.1.14.4.4.1.2	NonNegativeInteger32	read-only	The present output voltage.(*)
NUM upsOutputCurrent_fourth	1.3.6.1.4.1.818.1.1.14.4.4.1.3	NonNegativeInteger32	read-only	The present output current.(*)
NUM upsOutputPower_fourth	1.3.6.1.4.1.818.1.1.14.4.4.1.4	NonNegativeInteger32	read-only	The present output true power.(*)
I32 upsOutputPercentLoad_fourth	1.3.6.1.4.1.818.1.1.14.4.4.1.5	Integer32	read-only	The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)
upsBypass_fourth	1.3.6.1.4.1.818.1.1.14.5
NUM upsBypassFrequency_fourth	1.3.6.1.4.1.818.1.1.14.5.1	NonNegativeInteger32	read-only	The present bypass frequency.(*)
NUM upsBypassNumLines_fourth	1.3.6.1.4.1.818.1.1.14.5.2	NonNegativeInteger32	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)
upsBypassTable_fourth	1.3.6.1.4.1.818.1.1.14.5.3		not-accessible	A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)
upsBypassEntry_fourth	1.3.6.1.4.1.818.1.1.14.5.3.1		not-accessible	An entry containing information applicable to a particular bypass input.(*)
NUM upsBypassLineIndex_fourth	1.3.6.1.4.1.818.1.1.14.5.3.1.1	PositiveInteger32	not-accessible	The bypass line identifier.(*)
NUM upsBypassVoltage_fourth	1.3.6.1.4.1.818.1.1.14.5.3.1.2	NonNegativeInteger32	read-only	The present bypass voltage.(*)
NUM upsBypassCurrent_fourth	1.3.6.1.4.1.818.1.1.14.5.3.1.3	NonNegativeInteger32	read-only	The present bypass current.(*)
NUM upsBypassPower_fourth	1.3.6.1.4.1.818.1.1.14.5.3.1.4	NonNegativeInteger32	read-only	The present true power conveyed by the bypass.(*)
upsAlarm_fourth	1.3.6.1.4.1.818.1.1.14.6
G32 upsAlarmsPresent_fourth	1.3.6.1.4.1.818.1.1.14.6.1	Gauge32	read-only	The present number of active alarm conditions.(*)
upsAlarmTable_fourth	1.3.6.1.4.1.818.1.1.14.6.2		not-accessible	A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)
upsAlarmEntry_fourth	1.3.6.1.4.1.818.1.1.14.6.2.1		not-accessible	An entry containing information applicable to a particular alarm.(*)
NUM upsAlarmId_fourth	1.3.6.1.4.1.818.1.1.14.6.2.1.1	PositiveInteger32	not-accessible	A unique identifier for an alarm condition. This value must remain constant.(*)
OID upsAlarmDescr_fourth	1.3.6.1.4.1.818.1.1.14.6.2.1.2	AutonomousType	read-only	A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)
TIM upsAlarmTime_fourth	1.3.6.1.4.1.818.1.1.14.6.2.1.3	TimeStamp	read-only	The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)
upsWellKnownAlarms_fourth	1.3.6.1.4.1.818.1.1.14.6.3
upsAlarmBatteryBad_fourth	1.3.6.1.4.1.818.1.1.14.6.3.1			One or more batteries have been determined to require replacement.(*)
upsAlarmOnBattery_fourth	1.3.6.1.4.1.818.1.1.14.6.3.2			The UPS is drawing power from the batteries.(*)
upsAlarmLowBattery_fourth	1.3.6.1.4.1.818.1.1.14.6.3.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)
upsAlarmDepletedBattery_fourth	1.3.6.1.4.1.818.1.1.14.6.3.4			The UPS will be unable to sustain the present load when and if the utility power is lost.(*)
upsAlarmTempBad_fourth	1.3.6.1.4.1.818.1.1.14.6.3.5			A temperature is out of tolerance.(*)
upsAlarmInputBad_fourth	1.3.6.1.4.1.818.1.1.14.6.3.6			An input condition is out of tolerance.(*)
upsAlarmOutputBad_fourth	1.3.6.1.4.1.818.1.1.14.6.3.7			An output condition (other than OutputOverload) is out of tolerance.(*)
upsAlarmOutputOverload_fourth	1.3.6.1.4.1.818.1.1.14.6.3.8			The output load exceeds the UPS output capacity.(*)
upsAlarmOnBypass_fourth	1.3.6.1.4.1.818.1.1.14.6.3.9			The Bypass is presently engaged on the UPS.(*)
upsAlarmBypassBad_fourth	1.3.6.1.4.1.818.1.1.14.6.3.10			The Bypass is out of tolerance.(*)
upsAlarmOutputOffAsRequested_fourth	1.3.6.1.4.1.818.1.1.14.6.3.11			The UPS has shutdown as requested, i.e., the output is off.(*)
upsAlarmUpsOffAsRequested_fourth	1.3.6.1.4.1.818.1.1.14.6.3.12			The entire UPS has shutdown as commanded.(*)
upsAlarmChargerFailed_fourth	1.3.6.1.4.1.818.1.1.14.6.3.13			An uncorrected problem has been detected within the UPS charger subsystem.(*)
upsAlarmUpsOutputOff_fourth	1.3.6.1.4.1.818.1.1.14.6.3.14			The output of the UPS is in the off state.(*)
upsAlarmUpsSystemOff_fourth	1.3.6.1.4.1.818.1.1.14.6.3.15			The UPS system is in the off state.(*)
upsAlarmFanFailure_fourth	1.3.6.1.4.1.818.1.1.14.6.3.16			The failure of one or more fans in the UPS has been detected.(*)
upsAlarmFuseFailure_fourth	1.3.6.1.4.1.818.1.1.14.6.3.17			The failure of one or more fuses has been detected.(*)
upsAlarmGeneralFault_fourth	1.3.6.1.4.1.818.1.1.14.6.3.18			A general fault in the UPS has been detected.(*)
upsAlarmDiagnosticTestFailed_fourth	1.3.6.1.4.1.818.1.1.14.6.3.19			The result of the last diagnostic test indicates a failure.(*)
upsAlarmCommunicationsLost_fourth	1.3.6.1.4.1.818.1.1.14.6.3.20			A problem has been encountered in the communications between the agent and the UPS.(*)
upsAlarmAwaitingPower_fourth	1.3.6.1.4.1.818.1.1.14.6.3.21			The UPS output is off and the UPS is awaiting the return of input power.(*)
upsAlarmShutdownPending_fourth	1.3.6.1.4.1.818.1.1.14.6.3.22			A upsShutdownAfterDelay countdown is underway.(*)
upsAlarmShutdownImminent_fourth	1.3.6.1.4.1.818.1.1.14.6.3.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)
upsAlarmTestInProgress_fourth	1.3.6.1.4.1.818.1.1.14.6.3.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)
upsAlarmReceptacleOff_fourth	1.3.6.1.4.1.818.1.1.14.6.3.25			The receptacle are switch off
NUM upsAlarmMaskA_fourth	1.3.6.1.4.1.818.1.1.14.6.4	NonNegativeInteger32	read-only	Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.
upsTest_fourth	1.3.6.1.4.1.818.1.1.14.7
OID upsTestId_fourth	1.3.6.1.4.1.818.1.1.14.7.1	OBJECT IDENTIFIER	read-write	The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)
TES upsTestSpinLock_fourth	1.3.6.1.4.1.818.1.1.14.7.2	TestAndIncr	read-write	A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: try-again: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager / short delay get (upsTestSpinLock) } lock-value = upsTestSpinLock / no test in progress, start the test / set (upsTestSpinLock = lock-value, upsTestId = requested-test) if (error-index == 1) { / (upsTestSpinLock failed) / / if problem is not access control, then some other manager slipped in ahead of us / goto try-again } if (error-index == 2) { / (upsTestId) / / cannot perform the test / give up } / test started ok / / wait for test completion by polling upsTestResultsSummary / get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } / when test completes, retrieve any additional test results / / if upsTestSpinLock == lock-value + 1, then these are our test / / results (as opposed to another manager's / The initial value of upsTestSpinLock at agent initialization shall be 1.()
INT upsTestResultsSummary_fourth	1.3.6.1.4.1.818.1.1.14.7.3	INTEGER	read-only	The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)
STR upsTestResultsDetail_fourth	1.3.6.1.4.1.818.1.1.14.7.4	DisplayString	read-only	Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)
TIM upsTestStartTime_fourth	1.3.6.1.4.1.818.1.1.14.7.5	TimeStamp	read-only	The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)
NUM upsTestElapsedTime_fourth	1.3.6.1.4.1.818.1.1.14.7.6	TimeInterval	read-only	The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)
upsWellKnownTests_fourth	1.3.6.1.4.1.818.1.1.14.7.7
upsTestNoTestsInitiated_fourth	1.3.6.1.4.1.818.1.1.14.7.7.1			No tests have been initiated and no test is in progress.(*)
upsTestAbortTestInProgress_fourth	1.3.6.1.4.1.818.1.1.14.7.7.2			The test in progress is to be aborted / the test in progress was aborted.(*)
upsTestGeneralSystemsTest_fourth	1.3.6.1.4.1.818.1.1.14.7.7.3			The manufacturer's standard test of UPS device systems.(*)
upsTestQuickBatteryTest_fourth	1.3.6.1.4.1.818.1.1.14.7.7.4			A test that is sufficient to determine if the battery needs replacement.(*)
upsTestDeepBatteryCalibration_fourth	1.3.6.1.4.1.818.1.1.14.7.7.5			The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)
upsControl_fourth	1.3.6.1.4.1.818.1.1.14.8
INT upsShutdownType_fourth	1.3.6.1.4.1.818.1.1.14.8.1	INTEGER	read-write	This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)
I32 upsShutdownAfterDelay_fourth	1.3.6.1.4.1.818.1.1.14.8.2	Integer32	read-write	Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)
I32 upsStartupAfterDelay_fourth	1.3.6.1.4.1.818.1.1.14.8.3	Integer32	read-write	Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)
I32 upsRebootWithDuration_fourth	1.3.6.1.4.1.818.1.1.14.8.4	Integer32	read-write	Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)
INT upsAutoRestart_fourth	1.3.6.1.4.1.818.1.1.14.8.5	INTEGER	read-write	Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)
NUM upsReceptaclesNum_fourth	1.3.6.1.4.1.818.1.1.14.8.6	NonNegativeInteger32	read-only	The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.
upsReceptacleTable_fourth	1.3.6.1.4.1.818.1.1.14.8.7		not-accessible	A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.
upsReceptacleEntry_fourth	1.3.6.1.4.1.818.1.1.14.8.7.1		not-accessible	An entry containing information applicable to a particular receptacle.
NUM upsReceptacleLineIndex_fourth	1.3.6.1.4.1.818.1.1.14.8.7.1.1	PositiveInteger32	not-accessible	The receptacle line identifier.
INT upsReceptacleOnOff_fourth	1.3.6.1.4.1.818.1.1.14.8.7.1.2	INTEGER	read-write	The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.
INT upsUPSMode_fourth	1.3.6.1.4.1.818.1.1.14.8.8	INTEGER	read-write	The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)
INT upsRectifierOnOff_fourth	1.3.6.1.4.1.818.1.1.14.8.9	INTEGER	read-write	The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.
INT upsBatteryChargeMethod_fourth	1.3.6.1.4.1.818.1.1.14.8.10	INTEGER	read-write	The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.
INT upsInverterOnOff_fourth	1.3.6.1.4.1.818.1.1.14.8.11	INTEGER	read-write	The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.
INT upsBypassOnOff_fourth	1.3.6.1.4.1.818.1.1.14.8.12	INTEGER	read-write	The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.
INT upsLoadSource_fourth	1.3.6.1.4.1.818.1.1.14.8.13	INTEGER	read-write	The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.
upsConfig_fourth	1.3.6.1.4.1.818.1.1.14.9
NUM upsConfigInputVoltage_fourth	1.3.6.1.4.1.818.1.1.14.9.1	NonNegativeInteger32	read-write	The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigInputFreq_fourth	1.3.6.1.4.1.818.1.1.14.9.2	NonNegativeInteger32	read-write	The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVoltage_fourth	1.3.6.1.4.1.818.1.1.14.9.3	NonNegativeInteger32	read-write	The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputFreq_fourth	1.3.6.1.4.1.818.1.1.14.9.4	NonNegativeInteger32	read-write	The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVA_fourth	1.3.6.1.4.1.818.1.1.14.9.5	NonNegativeInteger32	read-only	The magnitude of the nominal Volt-Amp rating.(*)
NUM upsConfigOutputPower_fourth	1.3.6.1.4.1.818.1.1.14.9.6	NonNegativeInteger32	read-only	The magnitude of the nominal true power rating.(*)
NUM upsConfigLowBattTime_fourth	1.3.6.1.4.1.818.1.1.14.9.7	NonNegativeInteger32	read-write	The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)
INT upsConfigAudibleStatus_fourth	1.3.6.1.4.1.818.1.1.14.9.8	INTEGER	read-write	The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)
NUM upsConfigLowVoltageTransferPoint_fourth	1.3.6.1.4.1.818.1.1.14.9.9	NonNegativeInteger32	read-write	The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigHighVoltageTransferPoint_fourth	1.3.6.1.4.1.818.1.1.14.9.10	NonNegativeInteger32	read-write	The maximum line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigBatteryCapacity_fourth	1.3.6.1.4.1.818.1.1.14.9.11	NonNegativeInteger32	read-write	The installed battery capacity. This value is the 'factory'-value, not the value after calibration.
NUM upsConfigBatteryChargeCurrent_fourth	1.3.6.1.4.1.818.1.1.14.9.12	NonNegativeInteger32	read-write	The maximum battery charge current, including external chargers.
INT upsConfigNoLoadShutdown_fourth	1.3.6.1.4.1.818.1.1.14.9.13	INTEGER	read-write	Dis- or enable 'no load' shutdown from the contact interface.
NUM upsConfigStartDelay_fourth	1.3.6.1.4.1.818.1.1.14.9.14	PositiveInteger32	read-write	Minimum required autonomy time before the UPS may perform an autorestart.
upsGetSet_fourth	1.3.6.1.4.1.818.1.1.14.10
NUM upsEventGetNext_fourth	1.3.6.1.4.1.818.1.1.14.10.1	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.
NUM upsEventGetPrevious_fourth	1.3.6.1.4.1.818.1.1.14.10.2	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMP-NOSUCHNAME for UPSs that don't support this command.
NUM upsEventSetStartingTimeStamp_fourth	1.3.6.1.4.1.818.1.1.14.10.3	NonNegativeInteger32	read-write	The timestamp which is used as starting point for downloading events from the UPS event buffer
NUM upsEventRetreiveCurrentTimeStamp_fourth	1.3.6.1.4.1.818.1.1.14.10.4	NonNegativeInteger32	read-only	The current timestamp is retreived from the UPS
NUM upsEventTableSize_fourth	1.3.6.1.4.1.818.1.1.14.10.5	NonNegativeInteger32	read-only	The number of entries in the event table. This object indicates the number of rows in the event table.
upsEventTable_fourth	1.3.6.1.4.1.818.1.1.14.10.6		not-accessible	A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.
upsEventEntry_fourth	1.3.6.1.4.1.818.1.1.14.10.6.1		not-accessible	An entry containing information applicable to a particular event.
NUM upsEventLineIndex_fourth	1.3.6.1.4.1.818.1.1.14.10.6.1.1	PositiveInteger32	not-accessible	The event line identifier.
NUM upsEventCode_fourth	1.3.6.1.4.1.818.1.1.14.10.6.1.2	NonNegativeInteger32	read-only	The event code in numerical format.
NUM upsEventStatus_fourth	1.3.6.1.4.1.818.1.1.14.10.6.1.3	NonNegativeInteger32	read-only	The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMP-NOSUCHNAME is returned.
NUM upsEventTime_fourth	1.3.6.1.4.1.818.1.1.14.10.6.1.4	NonNegativeInteger32	read-only	The timestamp of the moment the event was generated.
NUM upsParametersRead_fourth	1.3.6.1.4.1.818.1.1.14.10.7	PositiveInteger32	read-write	The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.
NUM upsParametersWrite_fourth	1.3.6.1.4.1.818.1.1.14.10.8	PositiveInteger32	read-write	The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the first value of the table with the lowest index number.
NUM upsParametersStartAddress_fourth	1.3.6.1.4.1.818.1.1.14.10.9	NonNegativeInteger32	read-write	The address which is used as starting point for downloading parameters from the UPS
NUM upsParameterTableSize_fourth	1.3.6.1.4.1.818.1.1.14.10.10	NonNegativeInteger32	read-only	The number of entries in the parameter table. This object indicates the number of rows in the parameter table.
upsParameterTable_fourth	1.3.6.1.4.1.818.1.1.14.10.11		not-accessible	A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite
upsParameterEntry_fourth	1.3.6.1.4.1.818.1.1.14.10.11.1		not-accessible	An entry containing information applicable to a particular parameter.
NUM upsParameterLineIndex_fourth	1.3.6.1.4.1.818.1.1.14.10.11.1.1	PositiveInteger32	not-accessible	The parameter line identifier.
I32 upsParameterValue_fourth	1.3.6.1.4.1.818.1.1.14.10.11.1.2	Integer32	read-write	The parameter value in numerical format.
NUM upsStatus_fourth	1.3.6.1.4.1.818.1.1.14.10.12	NonNegativeInteger32	read-only	The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMP-NOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0001h upsStatusEcomodeIsOn 2 0002h upsStatusBatteryIsCharging 4 0004h upsStatusBatteryIsDischarging 8 0008h upsStatusAlarmIsActive 16 0010h upsStatusRectifierIsOn 32 0020h upsStatusLowBattery 64 0040h upsStatusOnBypass 128 0080h upsStatusMainsBypassOK 256 0100h upsStatusMainsRectifierOK 512 0200h upsStatusDetourIsOn 1024 0400h upsStatusAcousticAlarmIsOn 2048 0800h - (not used.) 4096 1000h upsStatusInverterIsOn 8192 2000h upsStatusNotInParallel (Q1 open) 16384 4000h upsStatusResetLoadOff 32768 8000h upsStatusLoadOff
NUM upsMainsStatisticsMBfail_fourth	1.3.6.1.4.1.818.1.1.14.10.13	NonNegativeInteger32	read-only	Count of main bypass failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsMRfail_fourth	1.3.6.1.4.1.818.1.1.14.10.14	NonNegativeInteger32	read-only	Count of mains rectifier failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsB2_fourth	1.3.6.1.4.1.818.1.1.14.10.15	NonNegativeInteger32	read-only	Count of transients on the mains bypass (0..2 ms), during the last 7 days.
NUM upsMainsStatisticsB5_fourth	1.3.6.1.4.1.818.1.1.14.10.16	NonNegativeInteger32	read-only	Count of transients on the mains bypass (2..5 ms), during the last 7 days.
NUM upsMainsStatisticsB10_fourth	1.3.6.1.4.1.818.1.1.14.10.17	NonNegativeInteger32	read-only	Count of transients on the mains bypass (5..10 ms), during the last 7 days.
NUM upsMainsStatisticsB200_fourth	1.3.6.1.4.1.818.1.1.14.10.18	NonNegativeInteger32	read-only	Count of transients on the mains bypass (10..200 ms), during the last 7 days.
NUM upsMainsStatisticsBypRel_fourth	1.3.6.1.4.1.818.1.1.14.10.19	NonNegativeInteger32	read-only	Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.
NUM upsTime_fourth	1.3.6.1.4.1.818.1.1.14.10.20	NonNegativeInteger32	read-write	The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMP-fourthERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.
STR upsRequestPermission_fourth	1.3.6.1.4.1.818.1.1.14.10.21	DisplayString	write-only	An encrypted code is send to enable use of restricted write objects during a limited period of time.
I32 upsEventGetCode_fourth	1.3.6.1.4.1.818.1.1.14.10.22	Integer32	write-only	The code which is used as starting point to downloading the events from the UPS event buffer.
TES upsEventSpinLock_fourth	1.3.6.1.4.1.818.1.1.14.10.23	TestAndIncr	read-write	A spin lock on the event subsystem.
TES upsParameterSpinLock_fourth	1.3.6.1.4.1.818.1.1.14.10.24	TestAndIncr	read-write	A spin lock on the parameters subsystem.
geUPSTraps_fourth	1.3.6.1.4.1.818.1.1.14.11
NTF upsAlarmBatteryBadTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.1			One or more batteries have been determined to require replacement.
NTF upsAlarmOnBatteryTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.2			An On Battery condition is restored.
NTF upsAlarmLowBatteryTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.
NTF upsAlarmDepletedBatteryTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.4			The UPS will be unable to sustain the present load when and if the utility power is lost)
NTF upsAlarmTempBadTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.5			A temperature is out of tolerance.
NTF upsAlarmInputBadTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.6			An input condition is out of tolerance.
NTF upsAlarmOutputBadTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.7			An output condition (other than OutputOverload) is out of tolerance.
NTF upsAlarmOutputOverloadTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.8			The output load exceeds the UPS output capacity.
NTF upsAlarmOnBypassTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.9			The Bypass is presently engaged on the UPS.
NTF upsAlarmBypassBadTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.10			The Bypass is out of tolerance.
NTF upsAlarmOutputOffAsRequestedTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.11			The UPS has shutdown as requested, i.e., the output is off.
NTF upsAlarmUpsOffAsRequestedTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.12			The entire UPS has shutdown as commanded.
NTF upsAlarmChargerFailedTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.13			An uncorrected problem has been detected within the UPS charger subsystem.
NTF upsAlarmUpsOutputOffTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.14			The output of the UPS is in the off state.
NTF upsAlarmUpsSystemOffTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.15			The UPS system is in the off state.
NTF upsAlarmFanFailureTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.16			The failure of one or more fans in the UPS has been detected.
NTF upsAlarmFuseFailureTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.17			The failure of one or more fuses has been detected.
NTF upsAlarmGeneralFaultTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.18			A general fault in the UPS has been detected.
NTF upsAlarmDiagnosticTestFailedTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.19			The result of the last diagnostic test indicates a failure.
NTF upsAlarmCommunicationsLostTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.20			A problem has been encountered in the communication between the agent and the UPS.
NTF upsAlarmAwaitingPowerTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.21			The UPS output is off and the UPS is awaiting the return of the input power (*).
NTF upsAlarmShutdownPendingTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.22			A upsShutdownAfterDelay countdown is underway.
NTF upsAlarmShutdownImminentTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
NTF upsAlarmTestInProgressTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.
NTF upsAlarmReceptacleOffTrap_fourth	1.3.6.1.4.1.818.1.1.14.11.0.25			A receptacle has been switched off.
NTF upsAlarmBatteryBadRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.33			A Battery bad condition is restored.
NTF upsAlarmOnBatteryRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.34			The UPS is drawing power from mains again.
NTF upsAlarmLowBatteryRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.35			A Low Battery condition is restored.
NTF upsAlarmDepletedBatteryRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.36			A Depleted Battery condition is restored.
NTF upsAlarmTempBadRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.37			A bad temperature condition is restored.
NTF upsAlarmInputBadRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.38			An input bad condition is restored.
NTF upsAlarmOutputBadRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.39			An output bad condition is restored.
NTF upsAlarmOutputOverloadRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.40			An output overload condition is restored.
NTF upsAlarmOnBypassRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.41			An On Bypass condition is restored.
NTF upsAlarmBypassBadRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.42			A Bypass bad condition is restored.
NTF upsAlarmOutputOffAsRequestedRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.43			A request shutdown has been restored.
NTF upsAlarmUpsOffAsRequestedRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.44			A entire UPS command has been restored.
NTF upsAlarmChargerFailedRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.45			A Charger Failer condition is restored.
NTF upsAlarmUpsOutputOn_fourth	1.3.6.1.4.1.818.1.1.14.11.0.46			The output of the UPS switched in the on state.
NTF upsAlarmUpsSystemOn_fourth	1.3.6.1.4.1.818.1.1.14.11.0.47			The UPS system is switched in the on state.
NTF upsAlarmFanFailureRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.48			A Fan failure condition is restored.
NTF upsAlarmFuseFailureRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.49			A Fuse failure condition is restored.
NTF upsAlarmGeneralFaultRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.50			A general fault is restored.
NTF upsAlarmDiagnosticTestFailedRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.51			A last diagnostic test indicates a failure is restored.
NTF upsAlarmCommunicationsLostRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.52			A problem in the communication between the agent and the UPS is restored.
NTF upsAlarmAwaitingPowerRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.53			A awaiting power condition is restored (*).
NTF upsAlarmShutdownPendingRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.54			A upsShutdownAfterDelay countdown is restored.
NTF upsAlarmShutdownImminentRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.55			A shutdown imminent condition is restored.
NTF upsAlarmTestInProgressRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.56			The test is in progress is terminated.
NTF upsAlarmReceptacleOn_fourth	1.3.6.1.4.1.818.1.1.14.11.0.57			A receptacle has been switched on.
NTF upsAlarmValueLow_fourth	1.3.6.1.4.1.818.1.1.14.11.0.129			A measurement value reached a value below its low-level threshold.
NTF upsAlarmValueHigh_fourth	1.3.6.1.4.1.818.1.1.14.11.0.130			A measurement value reached a value higher than its high-level threshold.
NTF upsAlarmValueLowRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.133			A ValueLow alarm condition is restored.
NTF upsAlarmValueHighRestored_fourth	1.3.6.1.4.1.818.1.1.14.11.0.134			A ValueHigh alarm condition is restored.
geFifthUPS	1.3.6.1.4.1.818.1.1.15
upsIdent_fifth	1.3.6.1.4.1.818.1.1.15.1
STR upsIdentManufacturer_fifth	1.3.6.1.4.1.818.1.1.15.1.1	DisplayString	read-only	The name of the UPS manufacturer.(*)
STR upsIdentModel_fifth	1.3.6.1.4.1.818.1.1.15.1.2	DisplayString	read-only	The UPS Model designation.(*)
STR upsIdentUPSSoftwareVersion_fifth	1.3.6.1.4.1.818.1.1.15.1.3	DisplayString	read-only	The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)
STR upsIdentAgentSoftwareVersion_fifth	1.3.6.1.4.1.818.1.1.15.1.4	DisplayString	read-only	The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)
STR upsIdentName_fifth	1.3.6.1.4.1.818.1.1.15.1.5	DisplayString	read-write	A string identifying the UPS. This object should be set by the administrator.(*)
STR upsIdentAttachedDevices_fifth	1.3.6.1.4.1.818.1.1.15.1.6	DisplayString	read-write	A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)
STR upsIdentUPSSerialNumber_fifth	1.3.6.1.4.1.818.1.1.15.1.7	DisplayString	read-only	The UPS serial number
STR upsIdentComProtVersion_fifth	1.3.6.1.4.1.818.1.1.15.1.8	DisplayString	read-only	The IMV communication protocol version
NUM upsIdentOperatingTime_fifth	1.3.6.1.4.1.818.1.1.15.1.9	NonNegativeInteger32	read-only	The present value of the operating time. total 'on' time since UPS manufactured
upsBattery_fifth	1.3.6.1.4.1.818.1.1.15.2
INT upsBatteryStatus_fifth	1.3.6.1.4.1.818.1.1.15.2.1	INTEGER	read-only	The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)
NUM upsSecondsOnBattery_fifth	1.3.6.1.4.1.818.1.1.15.2.2	NonNegativeInteger32	read-only	If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)
NUM upsEstimatedMinutesRemaining_fifth	1.3.6.1.4.1.818.1.1.15.2.3	PositiveInteger32	read-only	An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)
I32 upsEstimatedChargeRemaining_fifth	1.3.6.1.4.1.818.1.1.15.2.4	Integer32	read-only	An estimate of the battery charge remaining expressed as a percent of full charge.(*)
NUM upsBatteryVoltage_fifth	1.3.6.1.4.1.818.1.1.15.2.5	NonNegativeInteger32	read-only	The magnitude of the present battery voltage.(*)
I32 upsBatteryCurrent_fifth	1.3.6.1.4.1.818.1.1.15.2.6	Integer32	read-only	The present battery current.(*)
I32 upsBatteryTemperature_fifth	1.3.6.1.4.1.818.1.1.15.2.7	Integer32	read-only	The ambient temperature at or near the UPS Battery casing.(*)
upsInput_fifth	1.3.6.1.4.1.818.1.1.15.3
C32 upsInputLineBads_fifth	1.3.6.1.4.1.818.1.1.15.3.1	Counter32	read-only	A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)
NUM upsInputNumLines_fifth	1.3.6.1.4.1.818.1.1.15.3.2	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)
upsInputTable_fifth	1.3.6.1.4.1.818.1.1.15.3.3		not-accessible	A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)
upsInputEntry_fifth	1.3.6.1.4.1.818.1.1.15.3.3.1		not-accessible	An entry containing information applicable to a particular input line.(*)
NUM upsInputLineIndex_fifth	1.3.6.1.4.1.818.1.1.15.3.3.1.1	PositiveInteger32	not-accessible	The input line identifier.(*)
NUM upsInputFrequency_fifth	1.3.6.1.4.1.818.1.1.15.3.3.1.2	NonNegativeInteger32	read-only	The present input frequency.(*)
NUM upsInputVoltage_fifth	1.3.6.1.4.1.818.1.1.15.3.3.1.3	NonNegativeInteger32	read-only	The magnitude of the present input voltage.(*)
NUM upsInputCurrent_fifth	1.3.6.1.4.1.818.1.1.15.3.3.1.4	NonNegativeInteger32	read-only	The magnitude of the present input current.(*)
NUM upsInputTruePower_fifth	1.3.6.1.4.1.818.1.1.15.3.3.1.5	NonNegativeInteger32	read-only	The magnitude of the present input true power.(*)
NUM upsInputVoltageMin_fifth	1.3.6.1.4.1.818.1.1.15.3.3.1.6	NonNegativeInteger32	read-only	The lowest magnitude of the input voltage since last read out.
NUM upsInputVoltageMax_fifth	1.3.6.1.4.1.818.1.1.15.3.3.1.7	NonNegativeInteger32	read-only	The highest magnitude of the input voltage since last read out.
upsOutput_fifth	1.3.6.1.4.1.818.1.1.15.4
INT upsOutputSource_fifth	1.3.6.1.4.1.818.1.1.15.4.1	INTEGER	read-only	The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)
NUM upsOutputFrequency_fifth	1.3.6.1.4.1.818.1.1.15.4.2	NonNegativeInteger32	read-only	The present output frequency.(*)
NUM upsOutputNumLines_fifth	1.3.6.1.4.1.818.1.1.15.4.3	NonNegativeInteger32	read-only	The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)
upsOutputTable_fifth	1.3.6.1.4.1.818.1.1.15.4.4		not-accessible	A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)
upsOutputEntry_fifth	1.3.6.1.4.1.818.1.1.15.4.4.1		not-accessible	An entry containing information applicable to a particular output line.(*)
NUM upsOutputLineIndex_fifth	1.3.6.1.4.1.818.1.1.15.4.4.1.1	PositiveInteger32	not-accessible	The output line identifier.(*)
NUM upsOutputVoltage_fifth	1.3.6.1.4.1.818.1.1.15.4.4.1.2	NonNegativeInteger32	read-only	The present output voltage.(*)
NUM upsOutputCurrent_fifth	1.3.6.1.4.1.818.1.1.15.4.4.1.3	NonNegativeInteger32	read-only	The present output current.(*)
NUM upsOutputPower_fifth	1.3.6.1.4.1.818.1.1.15.4.4.1.4	NonNegativeInteger32	read-only	The present output true power.(*)
I32 upsOutputPercentLoad_fifth	1.3.6.1.4.1.818.1.1.15.4.4.1.5	Integer32	read-only	The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)
upsBypass_fifth	1.3.6.1.4.1.818.1.1.15.5
NUM upsBypassFrequency_fifth	1.3.6.1.4.1.818.1.1.15.5.1	NonNegativeInteger32	read-only	The present bypass frequency.(*)
NUM upsBypassNumLines_fifth	1.3.6.1.4.1.818.1.1.15.5.2	NonNegativeInteger32	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)
upsBypassTable_fifth	1.3.6.1.4.1.818.1.1.15.5.3		not-accessible	A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)
upsBypassEntry_fifth	1.3.6.1.4.1.818.1.1.15.5.3.1		not-accessible	An entry containing information applicable to a particular bypass input.(*)
NUM upsBypassLineIndex_fifth	1.3.6.1.4.1.818.1.1.15.5.3.1.1	PositiveInteger32	not-accessible	The bypass line identifier.(*)
NUM upsBypassVoltage_fifth	1.3.6.1.4.1.818.1.1.15.5.3.1.2	NonNegativeInteger32	read-only	The present bypass voltage.(*)
NUM upsBypassCurrent_fifth	1.3.6.1.4.1.818.1.1.15.5.3.1.3	NonNegativeInteger32	read-only	The present bypass current.(*)
NUM upsBypassPower_fifth	1.3.6.1.4.1.818.1.1.15.5.3.1.4	NonNegativeInteger32	read-only	The present true power conveyed by the bypass.(*)
upsAlarm_fifth	1.3.6.1.4.1.818.1.1.15.6
G32 upsAlarmsPresent_fifth	1.3.6.1.4.1.818.1.1.15.6.1	Gauge32	read-only	The present number of active alarm conditions.(*)
upsAlarmTable_fifth	1.3.6.1.4.1.818.1.1.15.6.2		not-accessible	A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)
upsAlarmEntry_fifth	1.3.6.1.4.1.818.1.1.15.6.2.1		not-accessible	An entry containing information applicable to a particular alarm.(*)
NUM upsAlarmId_fifth	1.3.6.1.4.1.818.1.1.15.6.2.1.1	PositiveInteger32	not-accessible	A unique identifier for an alarm condition. This value must remain constant.(*)
OID upsAlarmDescr_fifth	1.3.6.1.4.1.818.1.1.15.6.2.1.2	AutonomousType	read-only	A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)
TIM upsAlarmTime_fifth	1.3.6.1.4.1.818.1.1.15.6.2.1.3	TimeStamp	read-only	The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)
upsWellKnownAlarms_fifth	1.3.6.1.4.1.818.1.1.15.6.3
upsAlarmBatteryBad_fifth	1.3.6.1.4.1.818.1.1.15.6.3.1			One or more batteries have been determined to require replacement.(*)
upsAlarmOnBattery_fifth	1.3.6.1.4.1.818.1.1.15.6.3.2			The UPS is drawing power from the batteries.(*)
upsAlarmLowBattery_fifth	1.3.6.1.4.1.818.1.1.15.6.3.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)
upsAlarmDepletedBattery_fifth	1.3.6.1.4.1.818.1.1.15.6.3.4			The UPS will be unable to sustain the present load when and if the utility power is lost.(*)
upsAlarmTempBad_fifth	1.3.6.1.4.1.818.1.1.15.6.3.5			A temperature is out of tolerance.(*)
upsAlarmInputBad_fifth	1.3.6.1.4.1.818.1.1.15.6.3.6			An input condition is out of tolerance.(*)
upsAlarmOutputBad_fifth	1.3.6.1.4.1.818.1.1.15.6.3.7			An output condition (other than OutputOverload) is out of tolerance.(*)
upsAlarmOutputOverload_fifth	1.3.6.1.4.1.818.1.1.15.6.3.8			The output load exceeds the UPS output capacity.(*)
upsAlarmOnBypass_fifth	1.3.6.1.4.1.818.1.1.15.6.3.9			The Bypass is presently engaged on the UPS.(*)
upsAlarmBypassBad_fifth	1.3.6.1.4.1.818.1.1.15.6.3.10			The Bypass is out of tolerance.(*)
upsAlarmOutputOffAsRequested_fifth	1.3.6.1.4.1.818.1.1.15.6.3.11			The UPS has shutdown as requested, i.e., the output is off.(*)
upsAlarmUpsOffAsRequested_fifth	1.3.6.1.4.1.818.1.1.15.6.3.12			The entire UPS has shutdown as commanded.(*)
upsAlarmChargerFailed_fifth	1.3.6.1.4.1.818.1.1.15.6.3.13			An uncorrected problem has been detected within the UPS charger subsystem.(*)
upsAlarmUpsOutputOff_fifth	1.3.6.1.4.1.818.1.1.15.6.3.14			The output of the UPS is in the off state.(*)
upsAlarmUpsSystemOff_fifth	1.3.6.1.4.1.818.1.1.15.6.3.15			The UPS system is in the off state.(*)
upsAlarmFanFailure_fifth	1.3.6.1.4.1.818.1.1.15.6.3.16			The failure of one or more fans in the UPS has been detected.(*)
upsAlarmFuseFailure_fifth	1.3.6.1.4.1.818.1.1.15.6.3.17			The failure of one or more fuses has been detected.(*)
upsAlarmGeneralFault_fifth	1.3.6.1.4.1.818.1.1.15.6.3.18			A general fault in the UPS has been detected.(*)
upsAlarmDiagnosticTestFailed_fifth	1.3.6.1.4.1.818.1.1.15.6.3.19			The result of the last diagnostic test indicates a failure.(*)
upsAlarmCommunicationsLost_fifth	1.3.6.1.4.1.818.1.1.15.6.3.20			A problem has been encountered in the communications between the agent and the UPS.(*)
upsAlarmAwaitingPower_fifth	1.3.6.1.4.1.818.1.1.15.6.3.21			The UPS output is off and the UPS is awaiting the return of input power.(*)
upsAlarmShutdownPending_fifth	1.3.6.1.4.1.818.1.1.15.6.3.22			A upsShutdownAfterDelay countdown is underway.(*)
upsAlarmShutdownImminent_fifth	1.3.6.1.4.1.818.1.1.15.6.3.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)
upsAlarmTestInProgress_fifth	1.3.6.1.4.1.818.1.1.15.6.3.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)
upsAlarmReceptacleOff_fifth	1.3.6.1.4.1.818.1.1.15.6.3.25			The receptacle are switch off
NUM upsAlarmMaskA_fifth	1.3.6.1.4.1.818.1.1.15.6.4	NonNegativeInteger32	read-only	Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.
upsTest_fifth	1.3.6.1.4.1.818.1.1.15.7
OID upsTestId_fifth	1.3.6.1.4.1.818.1.1.15.7.1	OBJECT IDENTIFIER	read-write	The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)
TES upsTestSpinLock_fifth	1.3.6.1.4.1.818.1.1.15.7.2	TestAndIncr	read-write	A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: try-again: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager / short delay get (upsTestSpinLock) } lock-value = upsTestSpinLock / no test in progress, start the test / set (upsTestSpinLock = lock-value, upsTestId = requested-test) if (error-index == 1) { / (upsTestSpinLock failed) / / if problem is not access control, then some other manager slipped in ahead of us / goto try-again } if (error-index == 2) { / (upsTestId) / / cannot perform the test / give up } / test started ok / / wait for test completion by polling upsTestResultsSummary / get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } / when test completes, retrieve any additional test results / / if upsTestSpinLock == lock-value + 1, then these are our test / / results (as opposed to another manager's / The initial value of upsTestSpinLock at agent initialization shall be 1.()
INT upsTestResultsSummary_fifth	1.3.6.1.4.1.818.1.1.15.7.3	INTEGER	read-only	The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)
STR upsTestResultsDetail_fifth	1.3.6.1.4.1.818.1.1.15.7.4	DisplayString	read-only	Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)
TIM upsTestStartTime_fifth	1.3.6.1.4.1.818.1.1.15.7.5	TimeStamp	read-only	The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)
NUM upsTestElapsedTime_fifth	1.3.6.1.4.1.818.1.1.15.7.6	TimeInterval	read-only	The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)
upsWellKnownTests_fifth	1.3.6.1.4.1.818.1.1.15.7.7
upsTestNoTestsInitiated_fifth	1.3.6.1.4.1.818.1.1.15.7.7.1			No tests have been initiated and no test is in progress.(*)
upsTestAbortTestInProgress_fifth	1.3.6.1.4.1.818.1.1.15.7.7.2			The test in progress is to be aborted / the test in progress was aborted.(*)
upsTestGeneralSystemsTest_fifth	1.3.6.1.4.1.818.1.1.15.7.7.3			The manufacturer's standard test of UPS device systems.(*)
upsTestQuickBatteryTest_fifth	1.3.6.1.4.1.818.1.1.15.7.7.4			A test that is sufficient to determine if the battery needs replacement.(*)
upsTestDeepBatteryCalibration_fifth	1.3.6.1.4.1.818.1.1.15.7.7.5			The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)
upsControl_fifth	1.3.6.1.4.1.818.1.1.15.8
INT upsShutdownType_fifth	1.3.6.1.4.1.818.1.1.15.8.1	INTEGER	read-write	This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)
I32 upsShutdownAfterDelay_fifth	1.3.6.1.4.1.818.1.1.15.8.2	Integer32	read-write	Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)
I32 upsStartupAfterDelay_fifth	1.3.6.1.4.1.818.1.1.15.8.3	Integer32	read-write	Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)
I32 upsRebootWithDuration_fifth	1.3.6.1.4.1.818.1.1.15.8.4	Integer32	read-write	Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)
INT upsAutoRestart_fifth	1.3.6.1.4.1.818.1.1.15.8.5	INTEGER	read-write	Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)
NUM upsReceptaclesNum_fifth	1.3.6.1.4.1.818.1.1.15.8.6	NonNegativeInteger32	read-only	The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.
upsReceptacleTable_fifth	1.3.6.1.4.1.818.1.1.15.8.7		not-accessible	A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.
upsReceptacleEntry_fifth	1.3.6.1.4.1.818.1.1.15.8.7.1		not-accessible	An entry containing information applicable to a particular receptacle.
NUM upsReceptacleLineIndex_fifth	1.3.6.1.4.1.818.1.1.15.8.7.1.1	PositiveInteger32	not-accessible	The receptacle line identifier.
INT upsReceptacleOnOff_fifth	1.3.6.1.4.1.818.1.1.15.8.7.1.2	INTEGER	read-write	The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.
INT upsUPSMode_fifth	1.3.6.1.4.1.818.1.1.15.8.8	INTEGER	read-write	The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)
INT upsRectifierOnOff_fifth	1.3.6.1.4.1.818.1.1.15.8.9	INTEGER	read-write	The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.
INT upsBatteryChargeMethod_fifth	1.3.6.1.4.1.818.1.1.15.8.10	INTEGER	read-write	The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.
INT upsInverterOnOff_fifth	1.3.6.1.4.1.818.1.1.15.8.11	INTEGER	read-write	The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.
INT upsBypassOnOff_fifth	1.3.6.1.4.1.818.1.1.15.8.12	INTEGER	read-write	The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.
INT upsLoadSource_fifth	1.3.6.1.4.1.818.1.1.15.8.13	INTEGER	read-write	The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.
upsConfig_fifth	1.3.6.1.4.1.818.1.1.15.9
NUM upsConfigInputVoltage_fifth	1.3.6.1.4.1.818.1.1.15.9.1	NonNegativeInteger32	read-write	The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigInputFreq_fifth	1.3.6.1.4.1.818.1.1.15.9.2	NonNegativeInteger32	read-write	The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVoltage_fifth	1.3.6.1.4.1.818.1.1.15.9.3	NonNegativeInteger32	read-write	The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputFreq_fifth	1.3.6.1.4.1.818.1.1.15.9.4	NonNegativeInteger32	read-write	The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVA_fifth	1.3.6.1.4.1.818.1.1.15.9.5	NonNegativeInteger32	read-only	The magnitude of the nominal Volt-Amp rating.(*)
NUM upsConfigOutputPower_fifth	1.3.6.1.4.1.818.1.1.15.9.6	NonNegativeInteger32	read-only	The magnitude of the nominal true power rating.(*)
NUM upsConfigLowBattTime_fifth	1.3.6.1.4.1.818.1.1.15.9.7	NonNegativeInteger32	read-write	The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)
INT upsConfigAudibleStatus_fifth	1.3.6.1.4.1.818.1.1.15.9.8	INTEGER	read-write	The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)
NUM upsConfigLowVoltageTransferPoint_fifth	1.3.6.1.4.1.818.1.1.15.9.9	NonNegativeInteger32	read-write	The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigHighVoltageTransferPoint_fifth	1.3.6.1.4.1.818.1.1.15.9.10	NonNegativeInteger32	read-write	The maximum line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigBatteryCapacity_fifth	1.3.6.1.4.1.818.1.1.15.9.11	NonNegativeInteger32	read-write	The installed battery capacity. This value is the 'factory'-value, not the value after calibration.
NUM upsConfigBatteryChargeCurrent_fifth	1.3.6.1.4.1.818.1.1.15.9.12	NonNegativeInteger32	read-write	The maximum battery charge current, including external chargers.
INT upsConfigNoLoadShutdown_fifth	1.3.6.1.4.1.818.1.1.15.9.13	INTEGER	read-write	Dis- or enable 'no load' shutdown from the contact interface.
NUM upsConfigStartDelay_fifth	1.3.6.1.4.1.818.1.1.15.9.14	PositiveInteger32	read-write	Minimum required autonomy time before the UPS may perform an autorestart.
upsGetSet_fifth	1.3.6.1.4.1.818.1.1.15.10
NUM upsEventGetNext_fifth	1.3.6.1.4.1.818.1.1.15.10.1	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.
NUM upsEventGetPrevious_fifth	1.3.6.1.4.1.818.1.1.15.10.2	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMP-NOSUCHNAME for UPSs that don't support this command.
NUM upsEventSetStartingTimeStamp_fifth	1.3.6.1.4.1.818.1.1.15.10.3	NonNegativeInteger32	read-write	The timestamp which is used as starting point for downloading events from the UPS event buffer
NUM upsEventRetreiveCurrentTimeStamp_fifth	1.3.6.1.4.1.818.1.1.15.10.4	NonNegativeInteger32	read-only	The current timestamp is retreived from the UPS
NUM upsEventTableSize_fifth	1.3.6.1.4.1.818.1.1.15.10.5	NonNegativeInteger32	read-only	The number of entries in the event table. This object indicates the number of rows in the event table.
upsEventTable_fifth	1.3.6.1.4.1.818.1.1.15.10.6		not-accessible	A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.
upsEventEntry_fifth	1.3.6.1.4.1.818.1.1.15.10.6.1		not-accessible	An entry containing information applicable to a particular event.
NUM upsEventLineIndex_fifth	1.3.6.1.4.1.818.1.1.15.10.6.1.1	PositiveInteger32	not-accessible	The event line identifier.
NUM upsEventCode_fifth	1.3.6.1.4.1.818.1.1.15.10.6.1.2	NonNegativeInteger32	read-only	The event code in numerical format.
NUM upsEventStatus_fifth	1.3.6.1.4.1.818.1.1.15.10.6.1.3	NonNegativeInteger32	read-only	The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMP-NOSUCHNAME is returned.
NUM upsEventTime_fifth	1.3.6.1.4.1.818.1.1.15.10.6.1.4	NonNegativeInteger32	read-only	The timestamp of the moment the event was generated.
NUM upsParametersRead_fifth	1.3.6.1.4.1.818.1.1.15.10.7	PositiveInteger32	read-write	The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.
NUM upsParametersWrite_fifth	1.3.6.1.4.1.818.1.1.15.10.8	PositiveInteger32	read-write	The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the first value of the table with the lowest index number.
NUM upsParametersStartAddress_fifth	1.3.6.1.4.1.818.1.1.15.10.9	NonNegativeInteger32	read-write	The address which is used as starting point for downloading parameters from the UPS
NUM upsParameterTableSize_fifth	1.3.6.1.4.1.818.1.1.15.10.10	NonNegativeInteger32	read-only	The number of entries in the parameter table. This object indicates the number of rows in the parameter table.
upsParameterTable_fifth	1.3.6.1.4.1.818.1.1.15.10.11		not-accessible	A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite
upsParameterEntry_fifth	1.3.6.1.4.1.818.1.1.15.10.11.1		not-accessible	An entry containing information applicable to a particular parameter.
NUM upsParameterLineIndex_fifth	1.3.6.1.4.1.818.1.1.15.10.11.1.1	PositiveInteger32	not-accessible	The parameter line identifier.
I32 upsParameterValue_fifth	1.3.6.1.4.1.818.1.1.15.10.11.1.2	Integer32	read-write	The parameter value in numerical format.
NUM upsStatus_fifth	1.3.6.1.4.1.818.1.1.15.10.12	NonNegativeInteger32	read-only	The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMP-NOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0001h upsStatusEcomodeIsOn 2 0002h upsStatusBatteryIsCharging 4 0004h upsStatusBatteryIsDischarging 8 0008h upsStatusAlarmIsActive 16 0010h upsStatusRectifierIsOn 32 0020h upsStatusLowBattery 64 0040h upsStatusOnBypass 128 0080h upsStatusMainsBypassOK 256 0100h upsStatusMainsRectifierOK 512 0200h upsStatusDetourIsOn 1024 0400h upsStatusAcousticAlarmIsOn 2048 0800h - (not used.) 4096 1000h upsStatusInverterIsOn 8192 2000h upsStatusNotInParallel (Q1 open) 16384 4000h upsStatusResetLoadOff 32768 8000h upsStatusLoadOff
NUM upsMainsStatisticsMBfail_fifth	1.3.6.1.4.1.818.1.1.15.10.13	NonNegativeInteger32	read-only	Count of main bypass failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsMRfail_fifth	1.3.6.1.4.1.818.1.1.15.10.14	NonNegativeInteger32	read-only	Count of mains rectifier failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsB2_fifth	1.3.6.1.4.1.818.1.1.15.10.15	NonNegativeInteger32	read-only	Count of transients on the mains bypass (0..2 ms), during the last 7 days.
NUM upsMainsStatisticsB5_fifth	1.3.6.1.4.1.818.1.1.15.10.16	NonNegativeInteger32	read-only	Count of transients on the mains bypass (2..5 ms), during the last 7 days.
NUM upsMainsStatisticsB10_fifth	1.3.6.1.4.1.818.1.1.15.10.17	NonNegativeInteger32	read-only	Count of transients on the mains bypass (5..10 ms), during the last 7 days.
NUM upsMainsStatisticsB200_fifth	1.3.6.1.4.1.818.1.1.15.10.18	NonNegativeInteger32	read-only	Count of transients on the mains bypass (10..200 ms), during the last 7 days.
NUM upsMainsStatisticsBypRel_fifth	1.3.6.1.4.1.818.1.1.15.10.19	NonNegativeInteger32	read-only	Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.
NUM upsTime_fifth	1.3.6.1.4.1.818.1.1.15.10.20	NonNegativeInteger32	read-write	The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMP-fifthERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.
STR upsRequestPermission_fifth	1.3.6.1.4.1.818.1.1.15.10.21	DisplayString	write-only	An encrypted code is send to enable use of restricted write objects during a limited period of time.
I32 upsEventGetCode_fifth	1.3.6.1.4.1.818.1.1.15.10.22	Integer32	write-only	The code which is used as starting point to downloading the events from the UPS event buffer.
TES upsEventSpinLock_fifth	1.3.6.1.4.1.818.1.1.15.10.23	TestAndIncr	read-write	A spin lock on the event subsystem.
TES upsParameterSpinLock_fifth	1.3.6.1.4.1.818.1.1.15.10.24	TestAndIncr	read-write	A spin lock on the parameters subsystem.
geUPSTraps_fifth	1.3.6.1.4.1.818.1.1.15.11
NTF upsAlarmBatteryBadTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.1			One or more batteries have been determined to require replacement.
NTF upsAlarmOnBatteryTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.2			An On Battery condition is restored.
NTF upsAlarmLowBatteryTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.
NTF upsAlarmDepletedBatteryTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.4			The UPS will be unable to sustain the present load when and if the utility power is lost)
NTF upsAlarmTempBadTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.5			A temperature is out of tolerance.
NTF upsAlarmInputBadTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.6			An input condition is out of tolerance.
NTF upsAlarmOutputBadTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.7			An output condition (other than OutputOverload) is out of tolerance.
NTF upsAlarmOutputOverloadTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.8			The output load exceeds the UPS output capacity.
NTF upsAlarmOnBypassTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.9			The Bypass is presently engaged on the UPS.
NTF upsAlarmBypassBadTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.10			The Bypass is out of tolerance.
NTF upsAlarmOutputOffAsRequestedTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.11			The UPS has shutdown as requested, i.e., the output is off.
NTF upsAlarmUpsOffAsRequestedTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.12			The entire UPS has shutdown as commanded.
NTF upsAlarmChargerFailedTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.13			An uncorrected problem has been detected within the UPS charger subsystem.
NTF upsAlarmUpsOutputOffTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.14			The output of the UPS is in the off state.
NTF upsAlarmUpsSystemOffTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.15			The UPS system is in the off state.
NTF upsAlarmFanFailureTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.16			The failure of one or more fans in the UPS has been detected.
NTF upsAlarmFuseFailureTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.17			The failure of one or more fuses has been detected.
NTF upsAlarmGeneralFaultTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.18			A general fault in the UPS has been detected.
NTF upsAlarmDiagnosticTestFailedTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.19			The result of the last diagnostic test indicates a failure.
NTF upsAlarmCommunicationsLostTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.20			A problem has been encountered in the communication between the agent and the UPS.
NTF upsAlarmAwaitingPowerTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.21			The UPS output is off and the UPS is awaiting the return of the input power (*).
NTF upsAlarmShutdownPendingTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.22			A upsShutdownAfterDelay countdown is underway.
NTF upsAlarmShutdownImminentTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
NTF upsAlarmTestInProgressTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.
NTF upsAlarmReceptacleOffTrap_fifth	1.3.6.1.4.1.818.1.1.15.11.0.25			A receptacle has been switched off.
NTF upsAlarmBatteryBadRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.33			A Battery bad condition is restored.
NTF upsAlarmOnBatteryRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.34			The UPS is drawing power from mains again.
NTF upsAlarmLowBatteryRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.35			A Low Battery condition is restored.
NTF upsAlarmDepletedBatteryRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.36			A Depleted Battery condition is restored.
NTF upsAlarmTempBadRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.37			A bad temperature condition is restored.
NTF upsAlarmInputBadRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.38			An input bad condition is restored.
NTF upsAlarmOutputBadRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.39			An output bad condition is restored.
NTF upsAlarmOutputOverloadRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.40			An output overload condition is restored.
NTF upsAlarmOnBypassRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.41			An On Bypass condition is restored.
NTF upsAlarmBypassBadRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.42			A Bypass bad condition is restored.
NTF upsAlarmOutputOffAsRequestedRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.43			A request shutdown has been restored.
NTF upsAlarmUpsOffAsRequestedRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.44			A entire UPS command has been restored.
NTF upsAlarmChargerFailedRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.45			A Charger Failer condition is restored.
NTF upsAlarmUpsOutputOn_fifth	1.3.6.1.4.1.818.1.1.15.11.0.46			The output of the UPS switched in the on state.
NTF upsAlarmUpsSystemOn_fifth	1.3.6.1.4.1.818.1.1.15.11.0.47			The UPS system is switched in the on state.
NTF upsAlarmFanFailureRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.48			A Fan failure condition is restored.
NTF upsAlarmFuseFailureRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.49			A Fuse failure condition is restored.
NTF upsAlarmGeneralFaultRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.50			A general fault is restored.
NTF upsAlarmDiagnosticTestFailedRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.51			A last diagnostic test indicates a failure is restored.
NTF upsAlarmCommunicationsLostRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.52			A problem in the communication between the agent and the UPS is restored.
NTF upsAlarmAwaitingPowerRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.53			A awaiting power condition is restored (*).
NTF upsAlarmShutdownPendingRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.54			A upsShutdownAfterDelay countdown is restored.
NTF upsAlarmShutdownImminentRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.55			A shutdown imminent condition is restored.
NTF upsAlarmTestInProgressRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.56			The test is in progress is terminated.
NTF upsAlarmReceptacleOn_fifth	1.3.6.1.4.1.818.1.1.15.11.0.57			A receptacle has been switched on.
NTF upsAlarmValueLow_fifth	1.3.6.1.4.1.818.1.1.15.11.0.129			A measurement value reached a value below its low-level threshold.
NTF upsAlarmValueHigh_fifth	1.3.6.1.4.1.818.1.1.15.11.0.130			A measurement value reached a value higher than its high-level threshold.
NTF upsAlarmValueLowRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.133			A ValueLow alarm condition is restored.
NTF upsAlarmValueHighRestored_fifth	1.3.6.1.4.1.818.1.1.15.11.0.134			A ValueHigh alarm condition is restored.
geSixthUPS	1.3.6.1.4.1.818.1.1.16
upsIdent_sixth	1.3.6.1.4.1.818.1.1.16.1
STR upsIdentManufacturer_sixth	1.3.6.1.4.1.818.1.1.16.1.1	DisplayString	read-only	The name of the UPS manufacturer.(*)
STR upsIdentModel_sixth	1.3.6.1.4.1.818.1.1.16.1.2	DisplayString	read-only	The UPS Model designation.(*)
STR upsIdentUPSSoftwareVersion_sixth	1.3.6.1.4.1.818.1.1.16.1.3	DisplayString	read-only	The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)
STR upsIdentAgentSoftwareVersion_sixth	1.3.6.1.4.1.818.1.1.16.1.4	DisplayString	read-only	The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)
STR upsIdentName_sixth	1.3.6.1.4.1.818.1.1.16.1.5	DisplayString	read-write	A string identifying the UPS. This object should be set by the administrator.(*)
STR upsIdentAttachedDevices_sixth	1.3.6.1.4.1.818.1.1.16.1.6	DisplayString	read-write	A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)
STR upsIdentUPSSerialNumber_sixth	1.3.6.1.4.1.818.1.1.16.1.7	DisplayString	read-only	The UPS serial number
STR upsIdentComProtVersion_sixth	1.3.6.1.4.1.818.1.1.16.1.8	DisplayString	read-only	The IMV communication protocol version
NUM upsIdentOperatingTime_sixth	1.3.6.1.4.1.818.1.1.16.1.9	NonNegativeInteger32	read-only	The present value of the operating time. total 'on' time since UPS manufactured
upsBattery_sixth	1.3.6.1.4.1.818.1.1.16.2
INT upsBatteryStatus_sixth	1.3.6.1.4.1.818.1.1.16.2.1	INTEGER	read-only	The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)
NUM upsSecondsOnBattery_sixth	1.3.6.1.4.1.818.1.1.16.2.2	NonNegativeInteger32	read-only	If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)
NUM upsEstimatedMinutesRemaining_sixth	1.3.6.1.4.1.818.1.1.16.2.3	PositiveInteger32	read-only	An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)
I32 upsEstimatedChargeRemaining_sixth	1.3.6.1.4.1.818.1.1.16.2.4	Integer32	read-only	An estimate of the battery charge remaining expressed as a percent of full charge.(*)
NUM upsBatteryVoltage_sixth	1.3.6.1.4.1.818.1.1.16.2.5	NonNegativeInteger32	read-only	The magnitude of the present battery voltage.(*)
I32 upsBatteryCurrent_sixth	1.3.6.1.4.1.818.1.1.16.2.6	Integer32	read-only	The present battery current.(*)
I32 upsBatteryTemperature_sixth	1.3.6.1.4.1.818.1.1.16.2.7	Integer32	read-only	The ambient temperature at or near the UPS Battery casing.(*)
upsInput_sixth	1.3.6.1.4.1.818.1.1.16.3
C32 upsInputLineBads_sixth	1.3.6.1.4.1.818.1.1.16.3.1	Counter32	read-only	A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)
NUM upsInputNumLines_sixth	1.3.6.1.4.1.818.1.1.16.3.2	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)
upsInputTable_sixth	1.3.6.1.4.1.818.1.1.16.3.3		not-accessible	A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)
upsInputEntry_sixth	1.3.6.1.4.1.818.1.1.16.3.3.1		not-accessible	An entry containing information applicable to a particular input line.(*)
NUM upsInputLineIndex_sixth	1.3.6.1.4.1.818.1.1.16.3.3.1.1	PositiveInteger32	not-accessible	The input line identifier.(*)
NUM upsInputFrequency_sixth	1.3.6.1.4.1.818.1.1.16.3.3.1.2	NonNegativeInteger32	read-only	The present input frequency.(*)
NUM upsInputVoltage_sixth	1.3.6.1.4.1.818.1.1.16.3.3.1.3	NonNegativeInteger32	read-only	The magnitude of the present input voltage.(*)
NUM upsInputCurrent_sixth	1.3.6.1.4.1.818.1.1.16.3.3.1.4	NonNegativeInteger32	read-only	The magnitude of the present input current.(*)
NUM upsInputTruePower_sixth	1.3.6.1.4.1.818.1.1.16.3.3.1.5	NonNegativeInteger32	read-only	The magnitude of the present input true power.(*)
NUM upsInputVoltageMin_sixth	1.3.6.1.4.1.818.1.1.16.3.3.1.6	NonNegativeInteger32	read-only	The lowest magnitude of the input voltage since last read out.
NUM upsInputVoltageMax_sixth	1.3.6.1.4.1.818.1.1.16.3.3.1.7	NonNegativeInteger32	read-only	The highest magnitude of the input voltage since last read out.
upsOutput_sixth	1.3.6.1.4.1.818.1.1.16.4
INT upsOutputSource_sixth	1.3.6.1.4.1.818.1.1.16.4.1	INTEGER	read-only	The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)
NUM upsOutputFrequency_sixth	1.3.6.1.4.1.818.1.1.16.4.2	NonNegativeInteger32	read-only	The present output frequency.(*)
NUM upsOutputNumLines_sixth	1.3.6.1.4.1.818.1.1.16.4.3	NonNegativeInteger32	read-only	The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)
upsOutputTable_sixth	1.3.6.1.4.1.818.1.1.16.4.4		not-accessible	A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)
upsOutputEntry_sixth	1.3.6.1.4.1.818.1.1.16.4.4.1		not-accessible	An entry containing information applicable to a particular output line.(*)
NUM upsOutputLineIndex_sixth	1.3.6.1.4.1.818.1.1.16.4.4.1.1	PositiveInteger32	not-accessible	The output line identifier.(*)
NUM upsOutputVoltage_sixth	1.3.6.1.4.1.818.1.1.16.4.4.1.2	NonNegativeInteger32	read-only	The present output voltage.(*)
NUM upsOutputCurrent_sixth	1.3.6.1.4.1.818.1.1.16.4.4.1.3	NonNegativeInteger32	read-only	The present output current.(*)
NUM upsOutputPower_sixth	1.3.6.1.4.1.818.1.1.16.4.4.1.4	NonNegativeInteger32	read-only	The present output true power.(*)
I32 upsOutputPercentLoad_sixth	1.3.6.1.4.1.818.1.1.16.4.4.1.5	Integer32	read-only	The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)
upsBypass_sixth	1.3.6.1.4.1.818.1.1.16.5
NUM upsBypassFrequency_sixth	1.3.6.1.4.1.818.1.1.16.5.1	NonNegativeInteger32	read-only	The present bypass frequency.(*)
NUM upsBypassNumLines_sixth	1.3.6.1.4.1.818.1.1.16.5.2	NonNegativeInteger32	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)
upsBypassTable_sixth	1.3.6.1.4.1.818.1.1.16.5.3		not-accessible	A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)
upsBypassEntry_sixth	1.3.6.1.4.1.818.1.1.16.5.3.1		not-accessible	An entry containing information applicable to a particular bypass input.(*)
NUM upsBypassLineIndex_sixth	1.3.6.1.4.1.818.1.1.16.5.3.1.1	PositiveInteger32	not-accessible	The bypass line identifier.(*)
NUM upsBypassVoltage_sixth	1.3.6.1.4.1.818.1.1.16.5.3.1.2	NonNegativeInteger32	read-only	The present bypass voltage.(*)
NUM upsBypassCurrent_sixth	1.3.6.1.4.1.818.1.1.16.5.3.1.3	NonNegativeInteger32	read-only	The present bypass current.(*)
NUM upsBypassPower_sixth	1.3.6.1.4.1.818.1.1.16.5.3.1.4	NonNegativeInteger32	read-only	The present true power conveyed by the bypass.(*)
upsAlarm_sixth	1.3.6.1.4.1.818.1.1.16.6
G32 upsAlarmsPresent_sixth	1.3.6.1.4.1.818.1.1.16.6.1	Gauge32	read-only	The present number of active alarm conditions.(*)
upsAlarmTable_sixth	1.3.6.1.4.1.818.1.1.16.6.2		not-accessible	A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)
upsAlarmEntry_sixth	1.3.6.1.4.1.818.1.1.16.6.2.1		not-accessible	An entry containing information applicable to a particular alarm.(*)
NUM upsAlarmId_sixth	1.3.6.1.4.1.818.1.1.16.6.2.1.1	PositiveInteger32	not-accessible	A unique identifier for an alarm condition. This value must remain constant.(*)
OID upsAlarmDescr_sixth	1.3.6.1.4.1.818.1.1.16.6.2.1.2	AutonomousType	read-only	A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)
TIM upsAlarmTime_sixth	1.3.6.1.4.1.818.1.1.16.6.2.1.3	TimeStamp	read-only	The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)
upsWellKnownAlarms_sixth	1.3.6.1.4.1.818.1.1.16.6.3
upsAlarmBatteryBad_sixth	1.3.6.1.4.1.818.1.1.16.6.3.1			One or more batteries have been determined to require replacement.(*)
upsAlarmOnBattery_sixth	1.3.6.1.4.1.818.1.1.16.6.3.2			The UPS is drawing power from the batteries.(*)
upsAlarmLowBattery_sixth	1.3.6.1.4.1.818.1.1.16.6.3.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)
upsAlarmDepletedBattery_sixth	1.3.6.1.4.1.818.1.1.16.6.3.4			The UPS will be unable to sustain the present load when and if the utility power is lost.(*)
upsAlarmTempBad_sixth	1.3.6.1.4.1.818.1.1.16.6.3.5			A temperature is out of tolerance.(*)
upsAlarmInputBad_sixth	1.3.6.1.4.1.818.1.1.16.6.3.6			An input condition is out of tolerance.(*)
upsAlarmOutputBad_sixth	1.3.6.1.4.1.818.1.1.16.6.3.7			An output condition (other than OutputOverload) is out of tolerance.(*)
upsAlarmOutputOverload_sixth	1.3.6.1.4.1.818.1.1.16.6.3.8			The output load exceeds the UPS output capacity.(*)
upsAlarmOnBypass_sixth	1.3.6.1.4.1.818.1.1.16.6.3.9			The Bypass is presently engaged on the UPS.(*)
upsAlarmBypassBad_sixth	1.3.6.1.4.1.818.1.1.16.6.3.10			The Bypass is out of tolerance.(*)
upsAlarmOutputOffAsRequested_sixth	1.3.6.1.4.1.818.1.1.16.6.3.11			The UPS has shutdown as requested, i.e., the output is off.(*)
upsAlarmUpsOffAsRequested_sixth	1.3.6.1.4.1.818.1.1.16.6.3.12			The entire UPS has shutdown as commanded.(*)
upsAlarmChargerFailed_sixth	1.3.6.1.4.1.818.1.1.16.6.3.13			An uncorrected problem has been detected within the UPS charger subsystem.(*)
upsAlarmUpsOutputOff_sixth	1.3.6.1.4.1.818.1.1.16.6.3.14			The output of the UPS is in the off state.(*)
upsAlarmUpsSystemOff_sixth	1.3.6.1.4.1.818.1.1.16.6.3.15			The UPS system is in the off state.(*)
upsAlarmFanFailure_sixth	1.3.6.1.4.1.818.1.1.16.6.3.16			The failure of one or more fans in the UPS has been detected.(*)
upsAlarmFuseFailure_sixth	1.3.6.1.4.1.818.1.1.16.6.3.17			The failure of one or more fuses has been detected.(*)
upsAlarmGeneralFault_sixth	1.3.6.1.4.1.818.1.1.16.6.3.18			A general fault in the UPS has been detected.(*)
upsAlarmDiagnosticTestFailed_sixth	1.3.6.1.4.1.818.1.1.16.6.3.19			The result of the last diagnostic test indicates a failure.(*)
upsAlarmCommunicationsLost_sixth	1.3.6.1.4.1.818.1.1.16.6.3.20			A problem has been encountered in the communications between the agent and the UPS.(*)
upsAlarmAwaitingPower_sixth	1.3.6.1.4.1.818.1.1.16.6.3.21			The UPS output is off and the UPS is awaiting the return of input power.(*)
upsAlarmShutdownPending_sixth	1.3.6.1.4.1.818.1.1.16.6.3.22			A upsShutdownAfterDelay countdown is underway.(*)
upsAlarmShutdownImminent_sixth	1.3.6.1.4.1.818.1.1.16.6.3.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)
upsAlarmTestInProgress_sixth	1.3.6.1.4.1.818.1.1.16.6.3.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)
upsAlarmReceptacleOff_sixth	1.3.6.1.4.1.818.1.1.16.6.3.25			The receptacle are switch off
NUM upsAlarmMaskA_sixth	1.3.6.1.4.1.818.1.1.16.6.4	NonNegativeInteger32	read-only	Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.
upsTest_sixth	1.3.6.1.4.1.818.1.1.16.7
OID upsTestId_sixth	1.3.6.1.4.1.818.1.1.16.7.1	OBJECT IDENTIFIER	read-write	The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)
TES upsTestSpinLock_sixth	1.3.6.1.4.1.818.1.1.16.7.2	TestAndIncr	read-write	A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: try-again: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager / short delay get (upsTestSpinLock) } lock-value = upsTestSpinLock / no test in progress, start the test / set (upsTestSpinLock = lock-value, upsTestId = requested-test) if (error-index == 1) { / (upsTestSpinLock failed) / / if problem is not access control, then some other manager slipped in ahead of us / goto try-again } if (error-index == 2) { / (upsTestId) / / cannot perform the test / give up } / test started ok / / wait for test completion by polling upsTestResultsSummary / get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } / when test completes, retrieve any additional test results / / if upsTestSpinLock == lock-value + 1, then these are our test / / results (as opposed to another manager's / The initial value of upsTestSpinLock at agent initialization shall be 1.()
INT upsTestResultsSummary_sixth	1.3.6.1.4.1.818.1.1.16.7.3	INTEGER	read-only	The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)
STR upsTestResultsDetail_sixth	1.3.6.1.4.1.818.1.1.16.7.4	DisplayString	read-only	Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)
TIM upsTestStartTime_sixth	1.3.6.1.4.1.818.1.1.16.7.5	TimeStamp	read-only	The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)
NUM upsTestElapsedTime_sixth	1.3.6.1.4.1.818.1.1.16.7.6	TimeInterval	read-only	The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)
upsWellKnownTests_sixth	1.3.6.1.4.1.818.1.1.16.7.7
upsTestNoTestsInitiated_sixth	1.3.6.1.4.1.818.1.1.16.7.7.1			No tests have been initiated and no test is in progress.(*)
upsTestAbortTestInProgress_sixth	1.3.6.1.4.1.818.1.1.16.7.7.2			The test in progress is to be aborted / the test in progress was aborted.(*)
upsTestGeneralSystemsTest_sixth	1.3.6.1.4.1.818.1.1.16.7.7.3			The manufacturer's standard test of UPS device systems.(*)
upsTestQuickBatteryTest_sixth	1.3.6.1.4.1.818.1.1.16.7.7.4			A test that is sufficient to determine if the battery needs replacement.(*)
upsTestDeepBatteryCalibration_sixth	1.3.6.1.4.1.818.1.1.16.7.7.5			The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)
upsControl_sixth	1.3.6.1.4.1.818.1.1.16.8
INT upsShutdownType_sixth	1.3.6.1.4.1.818.1.1.16.8.1	INTEGER	read-write	This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)
I32 upsShutdownAfterDelay_sixth	1.3.6.1.4.1.818.1.1.16.8.2	Integer32	read-write	Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)
I32 upsStartupAfterDelay_sixth	1.3.6.1.4.1.818.1.1.16.8.3	Integer32	read-write	Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)
I32 upsRebootWithDuration_sixth	1.3.6.1.4.1.818.1.1.16.8.4	Integer32	read-write	Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)
INT upsAutoRestart_sixth	1.3.6.1.4.1.818.1.1.16.8.5	INTEGER	read-write	Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)
NUM upsReceptaclesNum_sixth	1.3.6.1.4.1.818.1.1.16.8.6	NonNegativeInteger32	read-only	The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.
upsReceptacleTable_sixth	1.3.6.1.4.1.818.1.1.16.8.7		not-accessible	A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.
upsReceptacleEntry_sixth	1.3.6.1.4.1.818.1.1.16.8.7.1		not-accessible	An entry containing information applicable to a particular receptacle.
NUM upsReceptacleLineIndex_sixth	1.3.6.1.4.1.818.1.1.16.8.7.1.1	PositiveInteger32	not-accessible	The receptacle line identifier.
INT upsReceptacleOnOff_sixth	1.3.6.1.4.1.818.1.1.16.8.7.1.2	INTEGER	read-write	The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.
INT upsUPSMode_sixth	1.3.6.1.4.1.818.1.1.16.8.8	INTEGER	read-write	The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)
INT upsRectifierOnOff_sixth	1.3.6.1.4.1.818.1.1.16.8.9	INTEGER	read-write	The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.
INT upsBatteryChargeMethod_sixth	1.3.6.1.4.1.818.1.1.16.8.10	INTEGER	read-write	The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.
INT upsInverterOnOff_sixth	1.3.6.1.4.1.818.1.1.16.8.11	INTEGER	read-write	The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.
INT upsBypassOnOff_sixth	1.3.6.1.4.1.818.1.1.16.8.12	INTEGER	read-write	The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.
INT upsLoadSource_sixth	1.3.6.1.4.1.818.1.1.16.8.13	INTEGER	read-write	The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.
upsConfig_sixth	1.3.6.1.4.1.818.1.1.16.9
NUM upsConfigInputVoltage_sixth	1.3.6.1.4.1.818.1.1.16.9.1	NonNegativeInteger32	read-write	The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigInputFreq_sixth	1.3.6.1.4.1.818.1.1.16.9.2	NonNegativeInteger32	read-write	The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVoltage_sixth	1.3.6.1.4.1.818.1.1.16.9.3	NonNegativeInteger32	read-write	The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputFreq_sixth	1.3.6.1.4.1.818.1.1.16.9.4	NonNegativeInteger32	read-write	The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVA_sixth	1.3.6.1.4.1.818.1.1.16.9.5	NonNegativeInteger32	read-only	The magnitude of the nominal Volt-Amp rating.(*)
NUM upsConfigOutputPower_sixth	1.3.6.1.4.1.818.1.1.16.9.6	NonNegativeInteger32	read-only	The magnitude of the nominal true power rating.(*)
NUM upsConfigLowBattTime_sixth	1.3.6.1.4.1.818.1.1.16.9.7	NonNegativeInteger32	read-write	The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)
INT upsConfigAudibleStatus_sixth	1.3.6.1.4.1.818.1.1.16.9.8	INTEGER	read-write	The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)
NUM upsConfigLowVoltageTransferPoint_sixth	1.3.6.1.4.1.818.1.1.16.9.9	NonNegativeInteger32	read-write	The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigHighVoltageTransferPoint_sixth	1.3.6.1.4.1.818.1.1.16.9.10	NonNegativeInteger32	read-write	The maximum line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigBatteryCapacity_sixth	1.3.6.1.4.1.818.1.1.16.9.11	NonNegativeInteger32	read-write	The installed battery capacity. This value is the 'factory'-value, not the value after calibration.
NUM upsConfigBatteryChargeCurrent_sixth	1.3.6.1.4.1.818.1.1.16.9.12	NonNegativeInteger32	read-write	The maximum battery charge current, including external chargers.
INT upsConfigNoLoadShutdown_sixth	1.3.6.1.4.1.818.1.1.16.9.13	INTEGER	read-write	Dis- or enable 'no load' shutdown from the contact interface.
NUM upsConfigStartDelay_sixth	1.3.6.1.4.1.818.1.1.16.9.14	PositiveInteger32	read-write	Minimum required autonomy time before the UPS may perform an autorestart.
upsGetSet_sixth	1.3.6.1.4.1.818.1.1.16.10
NUM upsEventGetNext_sixth	1.3.6.1.4.1.818.1.1.16.10.1	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.
NUM upsEventGetPrevious_sixth	1.3.6.1.4.1.818.1.1.16.10.2	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMP-NOSUCHNAME for UPSs that don't support this command.
NUM upsEventSetStartingTimeStamp_sixth	1.3.6.1.4.1.818.1.1.16.10.3	NonNegativeInteger32	read-write	The timestamp which is used as starting point for downloading events from the UPS event buffer
NUM upsEventRetreiveCurrentTimeStamp_sixth	1.3.6.1.4.1.818.1.1.16.10.4	NonNegativeInteger32	read-only	The current timestamp is retreived from the UPS
NUM upsEventTableSize_sixth	1.3.6.1.4.1.818.1.1.16.10.5	NonNegativeInteger32	read-only	The number of entries in the event table. This object indicates the number of rows in the event table.
upsEventTable_sixth	1.3.6.1.4.1.818.1.1.16.10.6		not-accessible	A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.
upsEventEntry_sixth	1.3.6.1.4.1.818.1.1.16.10.6.1		not-accessible	An entry containing information applicable to a particular event.
NUM upsEventLineIndex_sixth	1.3.6.1.4.1.818.1.1.16.10.6.1.1	PositiveInteger32	not-accessible	The event line identifier.
NUM upsEventCode_sixth	1.3.6.1.4.1.818.1.1.16.10.6.1.2	NonNegativeInteger32	read-only	The event code in numerical format.
NUM upsEventStatus_sixth	1.3.6.1.4.1.818.1.1.16.10.6.1.3	NonNegativeInteger32	read-only	The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMP-NOSUCHNAME is returned.
NUM upsEventTime_sixth	1.3.6.1.4.1.818.1.1.16.10.6.1.4	NonNegativeInteger32	read-only	The timestamp of the moment the event was generated.
NUM upsParametersRead_sixth	1.3.6.1.4.1.818.1.1.16.10.7	PositiveInteger32	read-write	The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.
NUM upsParametersWrite_sixth	1.3.6.1.4.1.818.1.1.16.10.8	PositiveInteger32	read-write	The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the first value of the table with the lowest index number.
NUM upsParametersStartAddress_sixth	1.3.6.1.4.1.818.1.1.16.10.9	NonNegativeInteger32	read-write	The address which is used as starting point for downloading parameters from the UPS
NUM upsParameterTableSize_sixth	1.3.6.1.4.1.818.1.1.16.10.10	NonNegativeInteger32	read-only	The number of entries in the parameter table. This object indicates the number of rows in the parameter table.
upsParameterTable_sixth	1.3.6.1.4.1.818.1.1.16.10.11		not-accessible	A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite
upsParameterEntry_sixth	1.3.6.1.4.1.818.1.1.16.10.11.1		not-accessible	An entry containing information applicable to a particular parameter.
NUM upsParameterLineIndex_sixth	1.3.6.1.4.1.818.1.1.16.10.11.1.1	PositiveInteger32	not-accessible	The parameter line identifier.
I32 upsParameterValue_sixth	1.3.6.1.4.1.818.1.1.16.10.11.1.2	Integer32	read-write	The parameter value in numerical format.
NUM upsStatus_sixth	1.3.6.1.4.1.818.1.1.16.10.12	NonNegativeInteger32	read-only	The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMP-NOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0001h upsStatusEcomodeIsOn 2 0002h upsStatusBatteryIsCharging 4 0004h upsStatusBatteryIsDischarging 8 0008h upsStatusAlarmIsActive 16 0010h upsStatusRectifierIsOn 32 0020h upsStatusLowBattery 64 0040h upsStatusOnBypass 128 0080h upsStatusMainsBypassOK 256 0100h upsStatusMainsRectifierOK 512 0200h upsStatusDetourIsOn 1024 0400h upsStatusAcousticAlarmIsOn 2048 0800h - (not used.) 4096 1000h upsStatusInverterIsOn 8192 2000h upsStatusNotInParallel (Q1 open) 16384 4000h upsStatusResetLoadOff 32768 8000h upsStatusLoadOff
NUM upsMainsStatisticsMBfail_sixth	1.3.6.1.4.1.818.1.1.16.10.13	NonNegativeInteger32	read-only	Count of main bypass failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsMRfail_sixth	1.3.6.1.4.1.818.1.1.16.10.14	NonNegativeInteger32	read-only	Count of mains rectifier failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsB2_sixth	1.3.6.1.4.1.818.1.1.16.10.15	NonNegativeInteger32	read-only	Count of transients on the mains bypass (0..2 ms), during the last 7 days.
NUM upsMainsStatisticsB5_sixth	1.3.6.1.4.1.818.1.1.16.10.16	NonNegativeInteger32	read-only	Count of transients on the mains bypass (2..5 ms), during the last 7 days.
NUM upsMainsStatisticsB10_sixth	1.3.6.1.4.1.818.1.1.16.10.17	NonNegativeInteger32	read-only	Count of transients on the mains bypass (5..10 ms), during the last 7 days.
NUM upsMainsStatisticsB200_sixth	1.3.6.1.4.1.818.1.1.16.10.18	NonNegativeInteger32	read-only	Count of transients on the mains bypass (10..200 ms), during the last 7 days.
NUM upsMainsStatisticsBypRel_sixth	1.3.6.1.4.1.818.1.1.16.10.19	NonNegativeInteger32	read-only	Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.
NUM upsTime_sixth	1.3.6.1.4.1.818.1.1.16.10.20	NonNegativeInteger32	read-write	The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMP-sixthERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.
STR upsRequestPermission_sixth	1.3.6.1.4.1.818.1.1.16.10.21	DisplayString	write-only	An encrypted code is send to enable use of restricted write objects during a limited period of time.
I32 upsEventGetCode_sixth	1.3.6.1.4.1.818.1.1.16.10.22	Integer32	write-only	The code which is used as starting point to downloading the events from the UPS event buffer.
TES upsEventSpinLock_sixth	1.3.6.1.4.1.818.1.1.16.10.23	TestAndIncr	read-write	A spin lock on the event subsystem.
TES upsParameterSpinLock_sixth	1.3.6.1.4.1.818.1.1.16.10.24	TestAndIncr	read-write	A spin lock on the parameters subsystem.
geUPSTraps_sixth	1.3.6.1.4.1.818.1.1.16.11
NTF upsAlarmBatteryBadTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.1			One or more batteries have been determined to require replacement.
NTF upsAlarmOnBatteryTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.2			An On Battery condition is restored.
NTF upsAlarmLowBatteryTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.
NTF upsAlarmDepletedBatteryTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.4			The UPS will be unable to sustain the present load when and if the utility power is lost)
NTF upsAlarmTempBadTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.5			A temperature is out of tolerance.
NTF upsAlarmInputBadTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.6			An input condition is out of tolerance.
NTF upsAlarmOutputBadTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.7			An output condition (other than OutputOverload) is out of tolerance.
NTF upsAlarmOutputOverloadTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.8			The output load exceeds the UPS output capacity.
NTF upsAlarmOnBypassTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.9			The Bypass is presently engaged on the UPS.
NTF upsAlarmBypassBadTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.10			The Bypass is out of tolerance.
NTF upsAlarmOutputOffAsRequestedTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.11			The UPS has shutdown as requested, i.e., the output is off.
NTF upsAlarmUpsOffAsRequestedTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.12			The entire UPS has shutdown as commanded.
NTF upsAlarmChargerFailedTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.13			An uncorrected problem has been detected within the UPS charger subsystem.
NTF upsAlarmUpsOutputOffTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.14			The output of the UPS is in the off state.
NTF upsAlarmUpsSystemOffTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.15			The UPS system is in the off state.
NTF upsAlarmFanFailureTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.16			The failure of one or more fans in the UPS has been detected.
NTF upsAlarmFuseFailureTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.17			The failure of one or more fuses has been detected.
NTF upsAlarmGeneralFaultTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.18			A general fault in the UPS has been detected.
NTF upsAlarmDiagnosticTestFailedTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.19			The result of the last diagnostic test indicates a failure.
NTF upsAlarmCommunicationsLostTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.20			A problem has been encountered in the communication between the agent and the UPS.
NTF upsAlarmAwaitingPowerTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.21			The UPS output is off and the UPS is awaiting the return of the input power (*).
NTF upsAlarmShutdownPendingTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.22			A upsShutdownAfterDelay countdown is underway.
NTF upsAlarmShutdownImminentTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
NTF upsAlarmTestInProgressTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.
NTF upsAlarmReceptacleOffTrap_sixth	1.3.6.1.4.1.818.1.1.16.11.0.25			A receptacle has been switched off.
NTF upsAlarmBatteryBadRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.33			A Battery bad condition is restored.
NTF upsAlarmOnBatteryRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.34			The UPS is drawing power from mains again.
NTF upsAlarmLowBatteryRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.35			A Low Battery condition is restored.
NTF upsAlarmDepletedBatteryRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.36			A Depleted Battery condition is restored.
NTF upsAlarmTempBadRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.37			A bad temperature condition is restored.
NTF upsAlarmInputBadRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.38			An input bad condition is restored.
NTF upsAlarmOutputBadRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.39			An output bad condition is restored.
NTF upsAlarmOutputOverloadRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.40			An output overload condition is restored.
NTF upsAlarmOnBypassRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.41			An On Bypass condition is restored.
NTF upsAlarmBypassBadRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.42			A Bypass bad condition is restored.
NTF upsAlarmOutputOffAsRequestedRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.43			A request shutdown has been restored.
NTF upsAlarmUpsOffAsRequestedRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.44			A entire UPS command has been restored.
NTF upsAlarmChargerFailedRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.45			A Charger Failer condition is restored.
NTF upsAlarmUpsOutputOn_sixth	1.3.6.1.4.1.818.1.1.16.11.0.46			The output of the UPS switched in the on state.
NTF upsAlarmUpsSystemOn_sixth	1.3.6.1.4.1.818.1.1.16.11.0.47			The UPS system is switched in the on state.
NTF upsAlarmFanFailureRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.48			A Fan failure condition is restored.
NTF upsAlarmFuseFailureRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.49			A Fuse failure condition is restored.
NTF upsAlarmGeneralFaultRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.50			A general fault is restored.
NTF upsAlarmDiagnosticTestFailedRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.51			A last diagnostic test indicates a failure is restored.
NTF upsAlarmCommunicationsLostRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.52			A problem in the communication between the agent and the UPS is restored.
NTF upsAlarmAwaitingPowerRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.53			A awaiting power condition is restored (*).
NTF upsAlarmShutdownPendingRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.54			A upsShutdownAfterDelay countdown is restored.
NTF upsAlarmShutdownImminentRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.55			A shutdown imminent condition is restored.
NTF upsAlarmTestInProgressRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.56			The test is in progress is terminated.
NTF upsAlarmReceptacleOn_sixth	1.3.6.1.4.1.818.1.1.16.11.0.57			A receptacle has been switched on.
NTF upsAlarmValueLow_sixth	1.3.6.1.4.1.818.1.1.16.11.0.129			A measurement value reached a value below its low-level threshold.
NTF upsAlarmValueHigh_sixth	1.3.6.1.4.1.818.1.1.16.11.0.130			A measurement value reached a value higher than its high-level threshold.
NTF upsAlarmValueLowRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.133			A ValueLow alarm condition is restored.
NTF upsAlarmValueHighRestored_sixth	1.3.6.1.4.1.818.1.1.16.11.0.134			A ValueHigh alarm condition is restored.
geSeventhUPS	1.3.6.1.4.1.818.1.1.17
upsIdent_seventh	1.3.6.1.4.1.818.1.1.17.1
STR upsIdentManufacturer_seventh	1.3.6.1.4.1.818.1.1.17.1.1	DisplayString	read-only	The name of the UPS manufacturer.(*)
STR upsIdentModel_seventh	1.3.6.1.4.1.818.1.1.17.1.2	DisplayString	read-only	The UPS Model designation.(*)
STR upsIdentUPSSoftwareVersion_seventh	1.3.6.1.4.1.818.1.1.17.1.3	DisplayString	read-only	The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)
STR upsIdentAgentSoftwareVersion_seventh	1.3.6.1.4.1.818.1.1.17.1.4	DisplayString	read-only	The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)
STR upsIdentName_seventh	1.3.6.1.4.1.818.1.1.17.1.5	DisplayString	read-write	A string identifying the UPS. This object should be set by the administrator.(*)
STR upsIdentAttachedDevices_seventh	1.3.6.1.4.1.818.1.1.17.1.6	DisplayString	read-write	A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)
STR upsIdentUPSSerialNumber_seventh	1.3.6.1.4.1.818.1.1.17.1.7	DisplayString	read-only	The UPS serial number
STR upsIdentComProtVersion_seventh	1.3.6.1.4.1.818.1.1.17.1.8	DisplayString	read-only	The IMV communication protocol version
NUM upsIdentOperatingTime_seventh	1.3.6.1.4.1.818.1.1.17.1.9	NonNegativeInteger32	read-only	The present value of the operating time. total 'on' time since UPS manufactured
upsBattery_seventh	1.3.6.1.4.1.818.1.1.17.2
INT upsBatteryStatus_seventh	1.3.6.1.4.1.818.1.1.17.2.1	INTEGER	read-only	The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)
NUM upsSecondsOnBattery_seventh	1.3.6.1.4.1.818.1.1.17.2.2	NonNegativeInteger32	read-only	If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)
NUM upsEstimatedMinutesRemaining_seventh	1.3.6.1.4.1.818.1.1.17.2.3	PositiveInteger32	read-only	An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)
I32 upsEstimatedChargeRemaining_seventh	1.3.6.1.4.1.818.1.1.17.2.4	Integer32	read-only	An estimate of the battery charge remaining expressed as a percent of full charge.(*)
NUM upsBatteryVoltage_seventh	1.3.6.1.4.1.818.1.1.17.2.5	NonNegativeInteger32	read-only	The magnitude of the present battery voltage.(*)
I32 upsBatteryCurrent_seventh	1.3.6.1.4.1.818.1.1.17.2.6	Integer32	read-only	The present battery current.(*)
I32 upsBatteryTemperature_seventh	1.3.6.1.4.1.818.1.1.17.2.7	Integer32	read-only	The ambient temperature at or near the UPS Battery casing.(*)
upsInput_seventh	1.3.6.1.4.1.818.1.1.17.3
C32 upsInputLineBads_seventh	1.3.6.1.4.1.818.1.1.17.3.1	Counter32	read-only	A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)
NUM upsInputNumLines_seventh	1.3.6.1.4.1.818.1.1.17.3.2	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)
upsInputTable_seventh	1.3.6.1.4.1.818.1.1.17.3.3		not-accessible	A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)
upsInputEntry_seventh	1.3.6.1.4.1.818.1.1.17.3.3.1		not-accessible	An entry containing information applicable to a particular input line.(*)
NUM upsInputLineIndex_seventh	1.3.6.1.4.1.818.1.1.17.3.3.1.1	PositiveInteger32	not-accessible	The input line identifier.(*)
NUM upsInputFrequency_seventh	1.3.6.1.4.1.818.1.1.17.3.3.1.2	NonNegativeInteger32	read-only	The present input frequency.(*)
NUM upsInputVoltage_seventh	1.3.6.1.4.1.818.1.1.17.3.3.1.3	NonNegativeInteger32	read-only	The magnitude of the present input voltage.(*)
NUM upsInputCurrent_seventh	1.3.6.1.4.1.818.1.1.17.3.3.1.4	NonNegativeInteger32	read-only	The magnitude of the present input current.(*)
NUM upsInputTruePower_seventh	1.3.6.1.4.1.818.1.1.17.3.3.1.5	NonNegativeInteger32	read-only	The magnitude of the present input true power.(*)
NUM upsInputVoltageMin_seventh	1.3.6.1.4.1.818.1.1.17.3.3.1.6	NonNegativeInteger32	read-only	The lowest magnitude of the input voltage since last read out.
NUM upsInputVoltageMax_seventh	1.3.6.1.4.1.818.1.1.17.3.3.1.7	NonNegativeInteger32	read-only	The highest magnitude of the input voltage since last read out.
upsOutput_seventh	1.3.6.1.4.1.818.1.1.17.4
INT upsOutputSource_seventh	1.3.6.1.4.1.818.1.1.17.4.1	INTEGER	read-only	The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)
NUM upsOutputFrequency_seventh	1.3.6.1.4.1.818.1.1.17.4.2	NonNegativeInteger32	read-only	The present output frequency.(*)
NUM upsOutputNumLines_seventh	1.3.6.1.4.1.818.1.1.17.4.3	NonNegativeInteger32	read-only	The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)
upsOutputTable_seventh	1.3.6.1.4.1.818.1.1.17.4.4		not-accessible	A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)
upsOutputEntry_seventh	1.3.6.1.4.1.818.1.1.17.4.4.1		not-accessible	An entry containing information applicable to a particular output line.(*)
NUM upsOutputLineIndex_seventh	1.3.6.1.4.1.818.1.1.17.4.4.1.1	PositiveInteger32	not-accessible	The output line identifier.(*)
NUM upsOutputVoltage_seventh	1.3.6.1.4.1.818.1.1.17.4.4.1.2	NonNegativeInteger32	read-only	The present output voltage.(*)
NUM upsOutputCurrent_seventh	1.3.6.1.4.1.818.1.1.17.4.4.1.3	NonNegativeInteger32	read-only	The present output current.(*)
NUM upsOutputPower_seventh	1.3.6.1.4.1.818.1.1.17.4.4.1.4	NonNegativeInteger32	read-only	The present output true power.(*)
I32 upsOutputPercentLoad_seventh	1.3.6.1.4.1.818.1.1.17.4.4.1.5	Integer32	read-only	The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)
upsBypass_seventh	1.3.6.1.4.1.818.1.1.17.5
NUM upsBypassFrequency_seventh	1.3.6.1.4.1.818.1.1.17.5.1	NonNegativeInteger32	read-only	The present bypass frequency.(*)
NUM upsBypassNumLines_seventh	1.3.6.1.4.1.818.1.1.17.5.2	NonNegativeInteger32	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)
upsBypassTable_seventh	1.3.6.1.4.1.818.1.1.17.5.3		not-accessible	A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)
upsBypassEntry_seventh	1.3.6.1.4.1.818.1.1.17.5.3.1		not-accessible	An entry containing information applicable to a particular bypass input.(*)
NUM upsBypassLineIndex_seventh	1.3.6.1.4.1.818.1.1.17.5.3.1.1	PositiveInteger32	not-accessible	The bypass line identifier.(*)
NUM upsBypassVoltage_seventh	1.3.6.1.4.1.818.1.1.17.5.3.1.2	NonNegativeInteger32	read-only	The present bypass voltage.(*)
NUM upsBypassCurrent_seventh	1.3.6.1.4.1.818.1.1.17.5.3.1.3	NonNegativeInteger32	read-only	The present bypass current.(*)
NUM upsBypassPower_seventh	1.3.6.1.4.1.818.1.1.17.5.3.1.4	NonNegativeInteger32	read-only	The present true power conveyed by the bypass.(*)
upsAlarm_seventh	1.3.6.1.4.1.818.1.1.17.6
G32 upsAlarmsPresent_seventh	1.3.6.1.4.1.818.1.1.17.6.1	Gauge32	read-only	The present number of active alarm conditions.(*)
upsAlarmTable_seventh	1.3.6.1.4.1.818.1.1.17.6.2		not-accessible	A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)
upsAlarmEntry_seventh	1.3.6.1.4.1.818.1.1.17.6.2.1		not-accessible	An entry containing information applicable to a particular alarm.(*)
NUM upsAlarmId_seventh	1.3.6.1.4.1.818.1.1.17.6.2.1.1	PositiveInteger32	not-accessible	A unique identifier for an alarm condition. This value must remain constant.(*)
OID upsAlarmDescr_seventh	1.3.6.1.4.1.818.1.1.17.6.2.1.2	AutonomousType	read-only	A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)
TIM upsAlarmTime_seventh	1.3.6.1.4.1.818.1.1.17.6.2.1.3	TimeStamp	read-only	The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)
upsWellKnownAlarms_seventh	1.3.6.1.4.1.818.1.1.17.6.3
upsAlarmBatteryBad_seventh	1.3.6.1.4.1.818.1.1.17.6.3.1			One or more batteries have been determined to require replacement.(*)
upsAlarmOnBattery_seventh	1.3.6.1.4.1.818.1.1.17.6.3.2			The UPS is drawing power from the batteries.(*)
upsAlarmLowBattery_seventh	1.3.6.1.4.1.818.1.1.17.6.3.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)
upsAlarmDepletedBattery_seventh	1.3.6.1.4.1.818.1.1.17.6.3.4			The UPS will be unable to sustain the present load when and if the utility power is lost.(*)
upsAlarmTempBad_seventh	1.3.6.1.4.1.818.1.1.17.6.3.5			A temperature is out of tolerance.(*)
upsAlarmInputBad_seventh	1.3.6.1.4.1.818.1.1.17.6.3.6			An input condition is out of tolerance.(*)
upsAlarmOutputBad_seventh	1.3.6.1.4.1.818.1.1.17.6.3.7			An output condition (other than OutputOverload) is out of tolerance.(*)
upsAlarmOutputOverload_seventh	1.3.6.1.4.1.818.1.1.17.6.3.8			The output load exceeds the UPS output capacity.(*)
upsAlarmOnBypass_seventh	1.3.6.1.4.1.818.1.1.17.6.3.9			The Bypass is presently engaged on the UPS.(*)
upsAlarmBypassBad_seventh	1.3.6.1.4.1.818.1.1.17.6.3.10			The Bypass is out of tolerance.(*)
upsAlarmOutputOffAsRequested_seventh	1.3.6.1.4.1.818.1.1.17.6.3.11			The UPS has shutdown as requested, i.e., the output is off.(*)
upsAlarmUpsOffAsRequested_seventh	1.3.6.1.4.1.818.1.1.17.6.3.12			The entire UPS has shutdown as commanded.(*)
upsAlarmChargerFailed_seventh	1.3.6.1.4.1.818.1.1.17.6.3.13			An uncorrected problem has been detected within the UPS charger subsystem.(*)
upsAlarmUpsOutputOff_seventh	1.3.6.1.4.1.818.1.1.17.6.3.14			The output of the UPS is in the off state.(*)
upsAlarmUpsSystemOff_seventh	1.3.6.1.4.1.818.1.1.17.6.3.15			The UPS system is in the off state.(*)
upsAlarmFanFailure_seventh	1.3.6.1.4.1.818.1.1.17.6.3.16			The failure of one or more fans in the UPS has been detected.(*)
upsAlarmFuseFailure_seventh	1.3.6.1.4.1.818.1.1.17.6.3.17			The failure of one or more fuses has been detected.(*)
upsAlarmGeneralFault_seventh	1.3.6.1.4.1.818.1.1.17.6.3.18			A general fault in the UPS has been detected.(*)
upsAlarmDiagnosticTestFailed_seventh	1.3.6.1.4.1.818.1.1.17.6.3.19			The result of the last diagnostic test indicates a failure.(*)
upsAlarmCommunicationsLost_seventh	1.3.6.1.4.1.818.1.1.17.6.3.20			A problem has been encountered in the communications between the agent and the UPS.(*)
upsAlarmAwaitingPower_seventh	1.3.6.1.4.1.818.1.1.17.6.3.21			The UPS output is off and the UPS is awaiting the return of input power.(*)
upsAlarmShutdownPending_seventh	1.3.6.1.4.1.818.1.1.17.6.3.22			A upsShutdownAfterDelay countdown is underway.(*)
upsAlarmShutdownImminent_seventh	1.3.6.1.4.1.818.1.1.17.6.3.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)
upsAlarmTestInProgress_seventh	1.3.6.1.4.1.818.1.1.17.6.3.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)
upsAlarmReceptacleOff_seventh	1.3.6.1.4.1.818.1.1.17.6.3.25			The receptacle are switch off
NUM upsAlarmMaskA_seventh	1.3.6.1.4.1.818.1.1.17.6.4	NonNegativeInteger32	read-only	Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.
upsTest_seventh	1.3.6.1.4.1.818.1.1.17.7
OID upsTestId_seventh	1.3.6.1.4.1.818.1.1.17.7.1	OBJECT IDENTIFIER	read-write	The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)
TES upsTestSpinLock_seventh	1.3.6.1.4.1.818.1.1.17.7.2	TestAndIncr	read-write	A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: try-again: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager / short delay get (upsTestSpinLock) } lock-value = upsTestSpinLock / no test in progress, start the test / set (upsTestSpinLock = lock-value, upsTestId = requested-test) if (error-index == 1) { / (upsTestSpinLock failed) / / if problem is not access control, then some other manager slipped in ahead of us / goto try-again } if (error-index == 2) { / (upsTestId) / / cannot perform the test / give up } / test started ok / / wait for test completion by polling upsTestResultsSummary / get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } / when test completes, retrieve any additional test results / / if upsTestSpinLock == lock-value + 1, then these are our test / / results (as opposed to another manager's / The initial value of upsTestSpinLock at agent initialization shall be 1.()
INT upsTestResultsSummary_seventh	1.3.6.1.4.1.818.1.1.17.7.3	INTEGER	read-only	The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)
STR upsTestResultsDetail_seventh	1.3.6.1.4.1.818.1.1.17.7.4	DisplayString	read-only	Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)
TIM upsTestStartTime_seventh	1.3.6.1.4.1.818.1.1.17.7.5	TimeStamp	read-only	The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)
NUM upsTestElapsedTime_seventh	1.3.6.1.4.1.818.1.1.17.7.6	TimeInterval	read-only	The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)
upsWellKnownTests_seventh	1.3.6.1.4.1.818.1.1.17.7.7
upsTestNoTestsInitiated_seventh	1.3.6.1.4.1.818.1.1.17.7.7.1			No tests have been initiated and no test is in progress.(*)
upsTestAbortTestInProgress_seventh	1.3.6.1.4.1.818.1.1.17.7.7.2			The test in progress is to be aborted / the test in progress was aborted.(*)
upsTestGeneralSystemsTest_seventh	1.3.6.1.4.1.818.1.1.17.7.7.3			The manufacturer's standard test of UPS device systems.(*)
upsTestQuickBatteryTest_seventh	1.3.6.1.4.1.818.1.1.17.7.7.4			A test that is sufficient to determine if the battery needs replacement.(*)
upsTestDeepBatteryCalibration_seventh	1.3.6.1.4.1.818.1.1.17.7.7.5			The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)
upsControl_seventh	1.3.6.1.4.1.818.1.1.17.8
INT upsShutdownType_seventh	1.3.6.1.4.1.818.1.1.17.8.1	INTEGER	read-write	This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)
I32 upsShutdownAfterDelay_seventh	1.3.6.1.4.1.818.1.1.17.8.2	Integer32	read-write	Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)
I32 upsStartupAfterDelay_seventh	1.3.6.1.4.1.818.1.1.17.8.3	Integer32	read-write	Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)
I32 upsRebootWithDuration_seventh	1.3.6.1.4.1.818.1.1.17.8.4	Integer32	read-write	Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)
INT upsAutoRestart_seventh	1.3.6.1.4.1.818.1.1.17.8.5	INTEGER	read-write	Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)
NUM upsReceptaclesNum_seventh	1.3.6.1.4.1.818.1.1.17.8.6	NonNegativeInteger32	read-only	The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.
upsReceptacleTable_seventh	1.3.6.1.4.1.818.1.1.17.8.7		not-accessible	A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.
upsReceptacleEntry_seventh	1.3.6.1.4.1.818.1.1.17.8.7.1		not-accessible	An entry containing information applicable to a particular receptacle.
NUM upsReceptacleLineIndex_seventh	1.3.6.1.4.1.818.1.1.17.8.7.1.1	PositiveInteger32	not-accessible	The receptacle line identifier.
INT upsReceptacleOnOff_seventh	1.3.6.1.4.1.818.1.1.17.8.7.1.2	INTEGER	read-write	The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.
INT upsUPSMode_seventh	1.3.6.1.4.1.818.1.1.17.8.8	INTEGER	read-write	The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)
INT upsRectifierOnOff_seventh	1.3.6.1.4.1.818.1.1.17.8.9	INTEGER	read-write	The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.
INT upsBatteryChargeMethod_seventh	1.3.6.1.4.1.818.1.1.17.8.10	INTEGER	read-write	The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.
INT upsInverterOnOff_seventh	1.3.6.1.4.1.818.1.1.17.8.11	INTEGER	read-write	The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.
INT upsBypassOnOff_seventh	1.3.6.1.4.1.818.1.1.17.8.12	INTEGER	read-write	The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.
INT upsLoadSource_seventh	1.3.6.1.4.1.818.1.1.17.8.13	INTEGER	read-write	The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.
upsConfig_seventh	1.3.6.1.4.1.818.1.1.17.9
NUM upsConfigInputVoltage_seventh	1.3.6.1.4.1.818.1.1.17.9.1	NonNegativeInteger32	read-write	The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigInputFreq_seventh	1.3.6.1.4.1.818.1.1.17.9.2	NonNegativeInteger32	read-write	The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVoltage_seventh	1.3.6.1.4.1.818.1.1.17.9.3	NonNegativeInteger32	read-write	The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputFreq_seventh	1.3.6.1.4.1.818.1.1.17.9.4	NonNegativeInteger32	read-write	The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVA_seventh	1.3.6.1.4.1.818.1.1.17.9.5	NonNegativeInteger32	read-only	The magnitude of the nominal Volt-Amp rating.(*)
NUM upsConfigOutputPower_seventh	1.3.6.1.4.1.818.1.1.17.9.6	NonNegativeInteger32	read-only	The magnitude of the nominal true power rating.(*)
NUM upsConfigLowBattTime_seventh	1.3.6.1.4.1.818.1.1.17.9.7	NonNegativeInteger32	read-write	The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)
INT upsConfigAudibleStatus_seventh	1.3.6.1.4.1.818.1.1.17.9.8	INTEGER	read-write	The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)
NUM upsConfigLowVoltageTransferPoint_seventh	1.3.6.1.4.1.818.1.1.17.9.9	NonNegativeInteger32	read-write	The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigHighVoltageTransferPoint_seventh	1.3.6.1.4.1.818.1.1.17.9.10	NonNegativeInteger32	read-write	The maximum line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigBatteryCapacity_seventh	1.3.6.1.4.1.818.1.1.17.9.11	NonNegativeInteger32	read-write	The installed battery capacity. This value is the 'factory'-value, not the value after calibration.
NUM upsConfigBatteryChargeCurrent_seventh	1.3.6.1.4.1.818.1.1.17.9.12	NonNegativeInteger32	read-write	The maximum battery charge current, including external chargers.
INT upsConfigNoLoadShutdown_seventh	1.3.6.1.4.1.818.1.1.17.9.13	INTEGER	read-write	Dis- or enable 'no load' shutdown from the contact interface.
NUM upsConfigStartDelay_seventh	1.3.6.1.4.1.818.1.1.17.9.14	PositiveInteger32	read-write	Minimum required autonomy time before the UPS may perform an autorestart.
upsGetSet_seventh	1.3.6.1.4.1.818.1.1.17.10
NUM upsEventGetNext_seventh	1.3.6.1.4.1.818.1.1.17.10.1	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.
NUM upsEventGetPrevious_seventh	1.3.6.1.4.1.818.1.1.17.10.2	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMP-NOSUCHNAME for UPSs that don't support this command.
NUM upsEventSetStartingTimeStamp_seventh	1.3.6.1.4.1.818.1.1.17.10.3	NonNegativeInteger32	read-write	The timestamp which is used as starting point for downloading events from the UPS event buffer
NUM upsEventRetreiveCurrentTimeStamp_seventh	1.3.6.1.4.1.818.1.1.17.10.4	NonNegativeInteger32	read-only	The current timestamp is retreived from the UPS
NUM upsEventTableSize_seventh	1.3.6.1.4.1.818.1.1.17.10.5	NonNegativeInteger32	read-only	The number of entries in the event table. This object indicates the number of rows in the event table.
upsEventTable_seventh	1.3.6.1.4.1.818.1.1.17.10.6		not-accessible	A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.
upsEventEntry_seventh	1.3.6.1.4.1.818.1.1.17.10.6.1		not-accessible	An entry containing information applicable to a particular event.
NUM upsEventLineIndex_seventh	1.3.6.1.4.1.818.1.1.17.10.6.1.1	PositiveInteger32	not-accessible	The event line identifier.
NUM upsEventCode_seventh	1.3.6.1.4.1.818.1.1.17.10.6.1.2	NonNegativeInteger32	read-only	The event code in numerical format.
NUM upsEventStatus_seventh	1.3.6.1.4.1.818.1.1.17.10.6.1.3	NonNegativeInteger32	read-only	The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMP-NOSUCHNAME is returned.
NUM upsEventTime_seventh	1.3.6.1.4.1.818.1.1.17.10.6.1.4	NonNegativeInteger32	read-only	The timestamp of the moment the event was generated.
NUM upsParametersRead_seventh	1.3.6.1.4.1.818.1.1.17.10.7	PositiveInteger32	read-write	The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.
NUM upsParametersWrite_seventh	1.3.6.1.4.1.818.1.1.17.10.8	PositiveInteger32	read-write	The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the first value of the table with the lowest index number.
NUM upsParametersStartAddress_seventh	1.3.6.1.4.1.818.1.1.17.10.9	NonNegativeInteger32	read-write	The address which is used as starting point for downloading parameters from the UPS
NUM upsParameterTableSize_seventh	1.3.6.1.4.1.818.1.1.17.10.10	NonNegativeInteger32	read-only	The number of entries in the parameter table. This object indicates the number of rows in the parameter table.
upsParameterTable_seventh	1.3.6.1.4.1.818.1.1.17.10.11		not-accessible	A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite
upsParameterEntry_seventh	1.3.6.1.4.1.818.1.1.17.10.11.1		not-accessible	An entry containing information applicable to a particular parameter.
NUM upsParameterLineIndex_seventh	1.3.6.1.4.1.818.1.1.17.10.11.1.1	PositiveInteger32	not-accessible	The parameter line identifier.
I32 upsParameterValue_seventh	1.3.6.1.4.1.818.1.1.17.10.11.1.2	Integer32	read-write	The parameter value in numerical format.
NUM upsStatus_seventh	1.3.6.1.4.1.818.1.1.17.10.12	NonNegativeInteger32	read-only	The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMP-NOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0001h upsStatusEcomodeIsOn 2 0002h upsStatusBatteryIsCharging 4 0004h upsStatusBatteryIsDischarging 8 0008h upsStatusAlarmIsActive 16 0010h upsStatusRectifierIsOn 32 0020h upsStatusLowBattery 64 0040h upsStatusOnBypass 128 0080h upsStatusMainsBypassOK 256 0100h upsStatusMainsRectifierOK 512 0200h upsStatusDetourIsOn 1024 0400h upsStatusAcousticAlarmIsOn 2048 0800h - (not used.) 4096 1000h upsStatusInverterIsOn 8192 2000h upsStatusNotInParallel (Q1 open) 16384 4000h upsStatusResetLoadOff 32768 8000h upsStatusLoadOff
NUM upsMainsStatisticsMBfail_seventh	1.3.6.1.4.1.818.1.1.17.10.13	NonNegativeInteger32	read-only	Count of main bypass failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsMRfail_seventh	1.3.6.1.4.1.818.1.1.17.10.14	NonNegativeInteger32	read-only	Count of mains rectifier failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsB2_seventh	1.3.6.1.4.1.818.1.1.17.10.15	NonNegativeInteger32	read-only	Count of transients on the mains bypass (0..2 ms), during the last 7 days.
NUM upsMainsStatisticsB5_seventh	1.3.6.1.4.1.818.1.1.17.10.16	NonNegativeInteger32	read-only	Count of transients on the mains bypass (2..5 ms), during the last 7 days.
NUM upsMainsStatisticsB10_seventh	1.3.6.1.4.1.818.1.1.17.10.17	NonNegativeInteger32	read-only	Count of transients on the mains bypass (5..10 ms), during the last 7 days.
NUM upsMainsStatisticsB200_seventh	1.3.6.1.4.1.818.1.1.17.10.18	NonNegativeInteger32	read-only	Count of transients on the mains bypass (10..200 ms), during the last 7 days.
NUM upsMainsStatisticsBypRel_seventh	1.3.6.1.4.1.818.1.1.17.10.19	NonNegativeInteger32	read-only	Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.
NUM upsTime_seventh	1.3.6.1.4.1.818.1.1.17.10.20	NonNegativeInteger32	read-write	The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMP-seventhERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.
STR upsRequestPermission_seventh	1.3.6.1.4.1.818.1.1.17.10.21	DisplayString	write-only	An encrypted code is send to enable use of restricted write objects during a limited period of time.
I32 upsEventGetCode_seventh	1.3.6.1.4.1.818.1.1.17.10.22	Integer32	write-only	The code which is used as starting point to downloading the events from the UPS event buffer.
TES upsEventSpinLock_seventh	1.3.6.1.4.1.818.1.1.17.10.23	TestAndIncr	read-write	A spin lock on the event subsystem.
TES upsParameterSpinLock_seventh	1.3.6.1.4.1.818.1.1.17.10.24	TestAndIncr	read-write	A spin lock on the parameters subsystem.
geUPSTraps_seventh	1.3.6.1.4.1.818.1.1.17.11
NTF upsAlarmBatteryBadTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.1			One or more batteries have been determined to require replacement.
NTF upsAlarmOnBatteryTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.2			An On Battery condition is restored.
NTF upsAlarmLowBatteryTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.
NTF upsAlarmDepletedBatteryTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.4			The UPS will be unable to sustain the present load when and if the utility power is lost)
NTF upsAlarmTempBadTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.5			A temperature is out of tolerance.
NTF upsAlarmInputBadTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.6			An input condition is out of tolerance.
NTF upsAlarmOutputBadTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.7			An output condition (other than OutputOverload) is out of tolerance.
NTF upsAlarmOutputOverloadTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.8			The output load exceeds the UPS output capacity.
NTF upsAlarmOnBypassTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.9			The Bypass is presently engaged on the UPS.
NTF upsAlarmBypassBadTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.10			The Bypass is out of tolerance.
NTF upsAlarmOutputOffAsRequestedTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.11			The UPS has shutdown as requested, i.e., the output is off.
NTF upsAlarmUpsOffAsRequestedTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.12			The entire UPS has shutdown as commanded.
NTF upsAlarmChargerFailedTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.13			An uncorrected problem has been detected within the UPS charger subsystem.
NTF upsAlarmUpsOutputOffTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.14			The output of the UPS is in the off state.
NTF upsAlarmUpsSystemOffTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.15			The UPS system is in the off state.
NTF upsAlarmFanFailureTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.16			The failure of one or more fans in the UPS has been detected.
NTF upsAlarmFuseFailureTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.17			The failure of one or more fuses has been detected.
NTF upsAlarmGeneralFaultTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.18			A general fault in the UPS has been detected.
NTF upsAlarmDiagnosticTestFailedTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.19			The result of the last diagnostic test indicates a failure.
NTF upsAlarmCommunicationsLostTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.20			A problem has been encountered in the communication between the agent and the UPS.
NTF upsAlarmAwaitingPowerTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.21			The UPS output is off and the UPS is awaiting the return of the input power (*).
NTF upsAlarmShutdownPendingTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.22			A upsShutdownAfterDelay countdown is underway.
NTF upsAlarmShutdownImminentTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
NTF upsAlarmTestInProgressTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.
NTF upsAlarmReceptacleOffTrap_seventh	1.3.6.1.4.1.818.1.1.17.11.0.25			A receptacle has been switched off.
NTF upsAlarmBatteryBadRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.33			A Battery bad condition is restored.
NTF upsAlarmOnBatteryRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.34			The UPS is drawing power from mains again.
NTF upsAlarmLowBatteryRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.35			A Low Battery condition is restored.
NTF upsAlarmDepletedBatteryRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.36			A Depleted Battery condition is restored.
NTF upsAlarmTempBadRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.37			A bad temperature condition is restored.
NTF upsAlarmInputBadRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.38			An input bad condition is restored.
NTF upsAlarmOutputBadRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.39			An output bad condition is restored.
NTF upsAlarmOutputOverloadRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.40			An output overload condition is restored.
NTF upsAlarmOnBypassRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.41			An On Bypass condition is restored.
NTF upsAlarmBypassBadRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.42			A Bypass bad condition is restored.
NTF upsAlarmOutputOffAsRequestedRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.43			A request shutdown has been restored.
NTF upsAlarmUpsOffAsRequestedRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.44			A entire UPS command has been restored.
NTF upsAlarmChargerFailedRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.45			A Charger Failer condition is restored.
NTF upsAlarmUpsOutputOn_seventh	1.3.6.1.4.1.818.1.1.17.11.0.46			The output of the UPS switched in the on state.
NTF upsAlarmUpsSystemOn_seventh	1.3.6.1.4.1.818.1.1.17.11.0.47			The UPS system is switched in the on state.
NTF upsAlarmFanFailureRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.48			A Fan failure condition is restored.
NTF upsAlarmFuseFailureRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.49			A Fuse failure condition is restored.
NTF upsAlarmGeneralFaultRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.50			A general fault is restored.
NTF upsAlarmDiagnosticTestFailedRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.51			A last diagnostic test indicates a failure is restored.
NTF upsAlarmCommunicationsLostRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.52			A problem in the communication between the agent and the UPS is restored.
NTF upsAlarmAwaitingPowerRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.53			A awaiting power condition is restored (*).
NTF upsAlarmShutdownPendingRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.54			A upsShutdownAfterDelay countdown is restored.
NTF upsAlarmShutdownImminentRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.55			A shutdown imminent condition is restored.
NTF upsAlarmTestInProgressRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.56			The test is in progress is terminated.
NTF upsAlarmReceptacleOn_seventh	1.3.6.1.4.1.818.1.1.17.11.0.57			A receptacle has been switched on.
NTF upsAlarmValueLow_seventh	1.3.6.1.4.1.818.1.1.17.11.0.129			A measurement value reached a value below its low-level threshold.
NTF upsAlarmValueHigh_seventh	1.3.6.1.4.1.818.1.1.17.11.0.130			A measurement value reached a value higher than its high-level threshold.
NTF upsAlarmValueLowRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.133			A ValueLow alarm condition is restored.
NTF upsAlarmValueHighRestored_seventh	1.3.6.1.4.1.818.1.1.17.11.0.134			A ValueHigh alarm condition is restored.
geEighthUPS	1.3.6.1.4.1.818.1.1.18
upsIdent_eighth	1.3.6.1.4.1.818.1.1.18.1
STR upsIdentManufacturer_eighth	1.3.6.1.4.1.818.1.1.18.1.1	DisplayString	read-only	The name of the UPS manufacturer.(*)
STR upsIdentModel_eighth	1.3.6.1.4.1.818.1.1.18.1.2	DisplayString	read-only	The UPS Model designation.(*)
STR upsIdentUPSSoftwareVersion_eighth	1.3.6.1.4.1.818.1.1.18.1.3	DisplayString	read-only	The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.(*)
STR upsIdentAgentSoftwareVersion_eighth	1.3.6.1.4.1.818.1.1.18.1.4	DisplayString	read-only	The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.(*)
STR upsIdentName_eighth	1.3.6.1.4.1.818.1.1.18.1.5	DisplayString	read-write	A string identifying the UPS. This object should be set by the administrator.(*)
STR upsIdentAttachedDevices_eighth	1.3.6.1.4.1.818.1.1.18.1.6	DisplayString	read-write	A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.(*)
STR upsIdentUPSSerialNumber_eighth	1.3.6.1.4.1.818.1.1.18.1.7	DisplayString	read-only	The UPS serial number
STR upsIdentComProtVersion_eighth	1.3.6.1.4.1.818.1.1.18.1.8	DisplayString	read-only	The IMV communication protocol version
NUM upsIdentOperatingTime_eighth	1.3.6.1.4.1.818.1.1.18.1.9	NonNegativeInteger32	read-only	The present value of the operating time. total 'on' time since UPS manufactured
upsBattery_eighth	1.3.6.1.4.1.818.1.1.18.2
INT upsBatteryStatus_eighth	1.3.6.1.4.1.818.1.1.18.2.1	INTEGER	read-only	The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).(*)
NUM upsSecondsOnBattery_eighth	1.3.6.1.4.1.818.1.1.18.2.2	NonNegativeInteger32	read-only	If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.(*)
NUM upsEstimatedMinutesRemaining_eighth	1.3.6.1.4.1.818.1.1.18.2.3	PositiveInteger32	read-only	An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.(*)
I32 upsEstimatedChargeRemaining_eighth	1.3.6.1.4.1.818.1.1.18.2.4	Integer32	read-only	An estimate of the battery charge remaining expressed as a percent of full charge.(*)
NUM upsBatteryVoltage_eighth	1.3.6.1.4.1.818.1.1.18.2.5	NonNegativeInteger32	read-only	The magnitude of the present battery voltage.(*)
I32 upsBatteryCurrent_eighth	1.3.6.1.4.1.818.1.1.18.2.6	Integer32	read-only	The present battery current.(*)
I32 upsBatteryTemperature_eighth	1.3.6.1.4.1.818.1.1.18.2.7	Integer32	read-only	The ambient temperature at or near the UPS Battery casing.(*)
upsInput_eighth	1.3.6.1.4.1.818.1.1.18.3
C32 upsInputLineBads_eighth	1.3.6.1.4.1.818.1.1.18.3.1	Counter32	read-only	A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.(*)
NUM upsInputNumLines_eighth	1.3.6.1.4.1.818.1.1.18.3.2	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This variable indicates the number of rows in the input table.(*)
upsInputTable_eighth	1.3.6.1.4.1.818.1.1.18.3.3		not-accessible	A list of input table entries. The number of entries is given by the value of upsInputNumLines.(*)
upsInputEntry_eighth	1.3.6.1.4.1.818.1.1.18.3.3.1		not-accessible	An entry containing information applicable to a particular input line.(*)
NUM upsInputLineIndex_eighth	1.3.6.1.4.1.818.1.1.18.3.3.1.1	PositiveInteger32	not-accessible	The input line identifier.(*)
NUM upsInputFrequency_eighth	1.3.6.1.4.1.818.1.1.18.3.3.1.2	NonNegativeInteger32	read-only	The present input frequency.(*)
NUM upsInputVoltage_eighth	1.3.6.1.4.1.818.1.1.18.3.3.1.3	NonNegativeInteger32	read-only	The magnitude of the present input voltage.(*)
NUM upsInputCurrent_eighth	1.3.6.1.4.1.818.1.1.18.3.3.1.4	NonNegativeInteger32	read-only	The magnitude of the present input current.(*)
NUM upsInputTruePower_eighth	1.3.6.1.4.1.818.1.1.18.3.3.1.5	NonNegativeInteger32	read-only	The magnitude of the present input true power.(*)
NUM upsInputVoltageMin_eighth	1.3.6.1.4.1.818.1.1.18.3.3.1.6	NonNegativeInteger32	read-only	The lowest magnitude of the input voltage since last read out.
NUM upsInputVoltageMax_eighth	1.3.6.1.4.1.818.1.1.18.3.3.1.7	NonNegativeInteger32	read-only	The highest magnitude of the input voltage since last read out.
upsOutput_eighth	1.3.6.1.4.1.818.1.1.18.4
INT upsOutputSource_eighth	1.3.6.1.4.1.818.1.1.18.4.1	INTEGER	read-only	The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.(*)
NUM upsOutputFrequency_eighth	1.3.6.1.4.1.818.1.1.18.4.2	NonNegativeInteger32	read-only	The present output frequency.(*)
NUM upsOutputNumLines_eighth	1.3.6.1.4.1.818.1.1.18.4.3	NonNegativeInteger32	read-only	The number of output lines utilized in this device. This variable indicates the number of rows in the output table.(*)
upsOutputTable_eighth	1.3.6.1.4.1.818.1.1.18.4.4		not-accessible	A list of output table entries. The number of entries is given by the value of upsOutputNumLines.(*)
upsOutputEntry_eighth	1.3.6.1.4.1.818.1.1.18.4.4.1		not-accessible	An entry containing information applicable to a particular output line.(*)
NUM upsOutputLineIndex_eighth	1.3.6.1.4.1.818.1.1.18.4.4.1.1	PositiveInteger32	not-accessible	The output line identifier.(*)
NUM upsOutputVoltage_eighth	1.3.6.1.4.1.818.1.1.18.4.4.1.2	NonNegativeInteger32	read-only	The present output voltage.(*)
NUM upsOutputCurrent_eighth	1.3.6.1.4.1.818.1.1.18.4.4.1.3	NonNegativeInteger32	read-only	The present output current.(*)
NUM upsOutputPower_eighth	1.3.6.1.4.1.818.1.1.18.4.4.1.4	NonNegativeInteger32	read-only	The present output true power.(*)
I32 upsOutputPercentLoad_eighth	1.3.6.1.4.1.818.1.1.18.4.4.1.5	Integer32	read-only	The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)
upsBypass_eighth	1.3.6.1.4.1.818.1.1.18.5
NUM upsBypassFrequency_eighth	1.3.6.1.4.1.818.1.1.18.5.1	NonNegativeInteger32	read-only	The present bypass frequency.(*)
NUM upsBypassNumLines_eighth	1.3.6.1.4.1.818.1.1.18.5.2	NonNegativeInteger32	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.(*)
upsBypassTable_eighth	1.3.6.1.4.1.818.1.1.18.5.3		not-accessible	A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.(*)
upsBypassEntry_eighth	1.3.6.1.4.1.818.1.1.18.5.3.1		not-accessible	An entry containing information applicable to a particular bypass input.(*)
NUM upsBypassLineIndex_eighth	1.3.6.1.4.1.818.1.1.18.5.3.1.1	PositiveInteger32	not-accessible	The bypass line identifier.(*)
NUM upsBypassVoltage_eighth	1.3.6.1.4.1.818.1.1.18.5.3.1.2	NonNegativeInteger32	read-only	The present bypass voltage.(*)
NUM upsBypassCurrent_eighth	1.3.6.1.4.1.818.1.1.18.5.3.1.3	NonNegativeInteger32	read-only	The present bypass current.(*)
NUM upsBypassPower_eighth	1.3.6.1.4.1.818.1.1.18.5.3.1.4	NonNegativeInteger32	read-only	The present true power conveyed by the bypass.(*)
upsAlarm_eighth	1.3.6.1.4.1.818.1.1.18.6
G32 upsAlarmsPresent_eighth	1.3.6.1.4.1.818.1.1.18.6.1	Gauge32	read-only	The present number of active alarm conditions.(*)
upsAlarmTable_eighth	1.3.6.1.4.1.818.1.1.18.6.2		not-accessible	A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.(*)
upsAlarmEntry_eighth	1.3.6.1.4.1.818.1.1.18.6.2.1		not-accessible	An entry containing information applicable to a particular alarm.(*)
NUM upsAlarmId_eighth	1.3.6.1.4.1.818.1.1.18.6.2.1.1	PositiveInteger32	not-accessible	A unique identifier for an alarm condition. This value must remain constant.(*)
OID upsAlarmDescr_eighth	1.3.6.1.4.1.818.1.1.18.6.2.1.2	AutonomousType	read-only	A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)
TIM upsAlarmTime_eighth	1.3.6.1.4.1.818.1.1.18.6.2.1.3	TimeStamp	read-only	The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)
upsWellKnownAlarms_eighth	1.3.6.1.4.1.818.1.1.18.6.3
upsAlarmBatteryBad_eighth	1.3.6.1.4.1.818.1.1.18.6.3.1			One or more batteries have been determined to require replacement.(*)
upsAlarmOnBattery_eighth	1.3.6.1.4.1.818.1.1.18.6.3.2			The UPS is drawing power from the batteries.(*)
upsAlarmLowBattery_eighth	1.3.6.1.4.1.818.1.1.18.6.3.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.(*)
upsAlarmDepletedBattery_eighth	1.3.6.1.4.1.818.1.1.18.6.3.4			The UPS will be unable to sustain the present load when and if the utility power is lost.(*)
upsAlarmTempBad_eighth	1.3.6.1.4.1.818.1.1.18.6.3.5			A temperature is out of tolerance.(*)
upsAlarmInputBad_eighth	1.3.6.1.4.1.818.1.1.18.6.3.6			An input condition is out of tolerance.(*)
upsAlarmOutputBad_eighth	1.3.6.1.4.1.818.1.1.18.6.3.7			An output condition (other than OutputOverload) is out of tolerance.(*)
upsAlarmOutputOverload_eighth	1.3.6.1.4.1.818.1.1.18.6.3.8			The output load exceeds the UPS output capacity.(*)
upsAlarmOnBypass_eighth	1.3.6.1.4.1.818.1.1.18.6.3.9			The Bypass is presently engaged on the UPS.(*)
upsAlarmBypassBad_eighth	1.3.6.1.4.1.818.1.1.18.6.3.10			The Bypass is out of tolerance.(*)
upsAlarmOutputOffAsRequested_eighth	1.3.6.1.4.1.818.1.1.18.6.3.11			The UPS has shutdown as requested, i.e., the output is off.(*)
upsAlarmUpsOffAsRequested_eighth	1.3.6.1.4.1.818.1.1.18.6.3.12			The entire UPS has shutdown as commanded.(*)
upsAlarmChargerFailed_eighth	1.3.6.1.4.1.818.1.1.18.6.3.13			An uncorrected problem has been detected within the UPS charger subsystem.(*)
upsAlarmUpsOutputOff_eighth	1.3.6.1.4.1.818.1.1.18.6.3.14			The output of the UPS is in the off state.(*)
upsAlarmUpsSystemOff_eighth	1.3.6.1.4.1.818.1.1.18.6.3.15			The UPS system is in the off state.(*)
upsAlarmFanFailure_eighth	1.3.6.1.4.1.818.1.1.18.6.3.16			The failure of one or more fans in the UPS has been detected.(*)
upsAlarmFuseFailure_eighth	1.3.6.1.4.1.818.1.1.18.6.3.17			The failure of one or more fuses has been detected.(*)
upsAlarmGeneralFault_eighth	1.3.6.1.4.1.818.1.1.18.6.3.18			A general fault in the UPS has been detected.(*)
upsAlarmDiagnosticTestFailed_eighth	1.3.6.1.4.1.818.1.1.18.6.3.19			The result of the last diagnostic test indicates a failure.(*)
upsAlarmCommunicationsLost_eighth	1.3.6.1.4.1.818.1.1.18.6.3.20			A problem has been encountered in the communications between the agent and the UPS.(*)
upsAlarmAwaitingPower_eighth	1.3.6.1.4.1.818.1.1.18.6.3.21			The UPS output is off and the UPS is awaiting the return of input power.(*)
upsAlarmShutdownPending_eighth	1.3.6.1.4.1.818.1.1.18.6.3.22			A upsShutdownAfterDelay countdown is underway.(*)
upsAlarmShutdownImminent_eighth	1.3.6.1.4.1.818.1.1.18.6.3.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.(*)
upsAlarmTestInProgress_eighth	1.3.6.1.4.1.818.1.1.18.6.3.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.(*)
upsAlarmReceptacleOff_eighth	1.3.6.1.4.1.818.1.1.18.6.3.25			The receptacle are switch off
NUM upsAlarmMaskA_eighth	1.3.6.1.4.1.818.1.1.18.6.4	NonNegativeInteger32	read-only	Specifies which alarm can be handled by the UPS. The 'Mask' parameter is a Long Integer32. The meaning of every bit is the same as for the 'upsAlarmGroupA' command. A bit having value=1 indicates that the corresponding alarm is handled by the UPS.
upsTest_eighth	1.3.6.1.4.1.818.1.1.18.7
OID upsTestId_eighth	1.3.6.1.4.1.818.1.1.18.7.1	OBJECT IDENTIFIER	read-write	The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.(*)
TES upsTestSpinLock_eighth	1.3.6.1.4.1.818.1.1.18.7.2	TestAndIncr	read-write	A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: try-again: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager / short delay get (upsTestSpinLock) } lock-value = upsTestSpinLock / no test in progress, start the test / set (upsTestSpinLock = lock-value, upsTestId = requested-test) if (error-index == 1) { / (upsTestSpinLock failed) / / if problem is not access control, then some other manager slipped in ahead of us / goto try-again } if (error-index == 2) { / (upsTestId) / / cannot perform the test / give up } / test started ok / / wait for test completion by polling upsTestResultsSummary / get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } / when test completes, retrieve any additional test results / / if upsTestSpinLock == lock-value + 1, then these are our test / / results (as opposed to another manager's / The initial value of upsTestSpinLock at agent initialization shall be 1.()
INT upsTestResultsSummary_eighth	1.3.6.1.4.1.818.1.1.18.7.3	INTEGER	read-only	The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.(*)
STR upsTestResultsDetail_eighth	1.3.6.1.4.1.818.1.1.18.7.4	DisplayString	read-only	Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.(*)
TIM upsTestStartTime_eighth	1.3.6.1.4.1.818.1.1.18.7.5	TimeStamp	read-only	The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.(*)
NUM upsTestElapsedTime_eighth	1.3.6.1.4.1.818.1.1.18.7.6	TimeInterval	read-only	The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.(*)
upsWellKnownTests_eighth	1.3.6.1.4.1.818.1.1.18.7.7
upsTestNoTestsInitiated_eighth	1.3.6.1.4.1.818.1.1.18.7.7.1			No tests have been initiated and no test is in progress.(*)
upsTestAbortTestInProgress_eighth	1.3.6.1.4.1.818.1.1.18.7.7.2			The test in progress is to be aborted / the test in progress was aborted.(*)
upsTestGeneralSystemsTest_eighth	1.3.6.1.4.1.818.1.1.18.7.7.3			The manufacturer's standard test of UPS device systems.(*)
upsTestQuickBatteryTest_eighth	1.3.6.1.4.1.818.1.1.18.7.7.4			A test that is sufficient to determine if the battery needs replacement.(*)
upsTestDeepBatteryCalibration_eighth	1.3.6.1.4.1.818.1.1.18.7.7.5			The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.(*)
upsControl_eighth	1.3.6.1.4.1.818.1.1.18.8
INT upsShutdownType_eighth	1.3.6.1.4.1.818.1.1.18.8.1	INTEGER	read-write	This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.(*)
I32 upsShutdownAfterDelay_eighth	1.3.6.1.4.1.818.1.1.18.8.2	Integer32	read-write	Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.(*)
I32 upsStartupAfterDelay_eighth	1.3.6.1.4.1.818.1.1.18.8.3	Integer32	read-write	Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.(*)
I32 upsRebootWithDuration_eighth	1.3.6.1.4.1.818.1.1.18.8.4	Integer32	read-write	Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.(*)
INT upsAutoRestart_eighth	1.3.6.1.4.1.818.1.1.18.8.5	INTEGER	read-write	Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.(*)
NUM upsReceptaclesNum_eighth	1.3.6.1.4.1.818.1.1.18.8.6	NonNegativeInteger32	read-only	The number of receptacles utilized in this device. This entry indicates the number of rows in the receptacle table.
upsReceptacleTable_eighth	1.3.6.1.4.1.818.1.1.18.8.7		not-accessible	A list of receptacle table entries. The number of entries is given by the value of upsReceptacleNum.
upsReceptacleEntry_eighth	1.3.6.1.4.1.818.1.1.18.8.7.1		not-accessible	An entry containing information applicable to a particular receptacle.
NUM upsReceptacleLineIndex_eighth	1.3.6.1.4.1.818.1.1.18.8.7.1.1	PositiveInteger32	not-accessible	The receptacle line identifier.
INT upsReceptacleOnOff_eighth	1.3.6.1.4.1.818.1.1.18.8.7.1.2	INTEGER	read-write	The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state nothing will happen. After an autorestart (see upsAutoRestart) the receptacle will be on.
INT upsUPSMode_eighth	1.3.6.1.4.1.818.1.1.18.8.8	INTEGER	read-write	The operation mode off the UPS. Off-line indicates a mode in which the input power is transferred to the output directly or via a step-up or step-down transformer. On-line mode indicates a mode in which the output power is regenerated through some convertor. the operating mode of the UPS may be fixed, or may be selectable (e.g. an on-line UPS with ecomode)
INT upsRectifierOnOff_eighth	1.3.6.1.4.1.818.1.1.18.8.9	INTEGER	read-write	The present state of the rectifier. Setting this object to 'on' will cause the rectifier to be turned on. Setting this object to 'off' will turn the rectifier off. If the rectifier is already in the desired state nothing will happen.
INT upsBatteryChargeMethod_eighth	1.3.6.1.4.1.818.1.1.18.8.10	INTEGER	read-write	The present state of the charge method. Setting this object to 'Normal charge' will cause the battery to be charged using the normal method. Setting this object to 'Boost charge' will charge the battery in boost mode. If the charge method is already in the desired state nothing will happen.
INT upsInverterOnOff_eighth	1.3.6.1.4.1.818.1.1.18.8.11	INTEGER	read-write	The present state of the inverter. Setting this object to 'on' will cause the inverter to be turned on. Setting this object to 'off' will turn the inverter off. If the inverter is already in the desired state nothing will happen.
INT upsBypassOnOff_eighth	1.3.6.1.4.1.818.1.1.18.8.12	INTEGER	read-write	The present state of the bypass. Setting this object to 'on' will cause the bypass to be activated. Setting this object to 'off' will deactivate the bypass. If the UPS is already in the desired state nothing will happen.
INT upsLoadSource_eighth	1.3.6.1.4.1.818.1.1.18.8.13	INTEGER	read-write	The present source of the load. Setting this object to 'On bypass' will cause the load to be supplied by the bypass. Setting this object to 'On inverter' will cause the load to be supplied by the inverter. If the load is already supplied by the desired source nothing will happen.
upsConfig_eighth	1.3.6.1.4.1.818.1.1.18.9
NUM upsConfigInputVoltage_eighth	1.3.6.1.4.1.818.1.1.18.9.1	NonNegativeInteger32	read-write	The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigInputFreq_eighth	1.3.6.1.4.1.818.1.1.18.9.2	NonNegativeInteger32	read-write	The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVoltage_eighth	1.3.6.1.4.1.818.1.1.18.9.3	NonNegativeInteger32	read-write	The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputFreq_eighth	1.3.6.1.4.1.818.1.1.18.9.4	NonNegativeInteger32	read-write	The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.(*)
NUM upsConfigOutputVA_eighth	1.3.6.1.4.1.818.1.1.18.9.5	NonNegativeInteger32	read-only	The magnitude of the nominal Volt-Amp rating.(*)
NUM upsConfigOutputPower_eighth	1.3.6.1.4.1.818.1.1.18.9.6	NonNegativeInteger32	read-only	The magnitude of the nominal true power rating.(*)
NUM upsConfigLowBattTime_eighth	1.3.6.1.4.1.818.1.1.18.9.7	NonNegativeInteger32	read-write	The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.(*)
INT upsConfigAudibleStatus_eighth	1.3.6.1.4.1.818.1.1.18.9.8	INTEGER	read-write	The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.(*)
NUM upsConfigLowVoltageTransferPoint_eighth	1.3.6.1.4.1.818.1.1.18.9.9	NonNegativeInteger32	read-write	The minimum input line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigHighVoltageTransferPoint_eighth	1.3.6.1.4.1.818.1.1.18.9.10	NonNegativeInteger32	read-write	The maximum line voltage allowed before the UPS system transfers to battery backup.(*)
NUM upsConfigBatteryCapacity_eighth	1.3.6.1.4.1.818.1.1.18.9.11	NonNegativeInteger32	read-write	The installed battery capacity. This value is the 'factory'-value, not the value after calibration.
NUM upsConfigBatteryChargeCurrent_eighth	1.3.6.1.4.1.818.1.1.18.9.12	NonNegativeInteger32	read-write	The maximum battery charge current, including external chargers.
INT upsConfigNoLoadShutdown_eighth	1.3.6.1.4.1.818.1.1.18.9.13	INTEGER	read-write	Dis- or enable 'no load' shutdown from the contact interface.
NUM upsConfigStartDelay_eighth	1.3.6.1.4.1.818.1.1.18.9.14	PositiveInteger32	read-write	Minimum required autonomy time before the UPS may perform an autorestart.
upsGetSet_eighth	1.3.6.1.4.1.818.1.1.18.10
NUM upsEventGetNext_eighth	1.3.6.1.4.1.818.1.1.18.10.1	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventSetStartingTimeStamp will be used as the start value of the table with the lowest index number.
NUM upsEventGetPrevious_eighth	1.3.6.1.4.1.818.1.1.18.10.2	PositiveInteger32	read-write	The number of events to retreive from the UPS event buffer. When this object is set the EventTable will be filled with the requested number of entries. The value upsEventLastTime will be used as the last value of the table with the highest index number. Returns SNMP-NOSUCHNAME for UPSs that don't support this command.
NUM upsEventSetStartingTimeStamp_eighth	1.3.6.1.4.1.818.1.1.18.10.3	NonNegativeInteger32	read-write	The timestamp which is used as starting point for downloading events from the UPS event buffer
NUM upsEventRetreiveCurrentTimeStamp_eighth	1.3.6.1.4.1.818.1.1.18.10.4	NonNegativeInteger32	read-only	The current timestamp is retreived from the UPS
NUM upsEventTableSize_eighth	1.3.6.1.4.1.818.1.1.18.10.5	NonNegativeInteger32	read-only	The number of entries in the event table. This object indicates the number of rows in the event table.
upsEventTable_eighth	1.3.6.1.4.1.818.1.1.18.10.6		not-accessible	A list of event table entries. The number of entries is always 10, and the value of upsEventTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..10)): PDU-SET upsSetStartingTimeStamp PDU-SET upsEventGetNext PDU-GET upsEventTableSize PDU-GET upsEventCode,upsEventStatus,upsEventTime 1 PDU-GET upsEventCode,upsEventStatus,upsEventTime 2 .. PDU-GET upsEventCode,upsEventStatus,upsEventTime The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsEventTableSize.
upsEventEntry_eighth	1.3.6.1.4.1.818.1.1.18.10.6.1		not-accessible	An entry containing information applicable to a particular event.
NUM upsEventLineIndex_eighth	1.3.6.1.4.1.818.1.1.18.10.6.1.1	PositiveInteger32	not-accessible	The event line identifier.
NUM upsEventCode_eighth	1.3.6.1.4.1.818.1.1.18.10.6.1.2	NonNegativeInteger32	read-only	The event code in numerical format.
NUM upsEventStatus_eighth	1.3.6.1.4.1.818.1.1.18.10.6.1.3	NonNegativeInteger32	read-only	The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMP-NOSUCHNAME is returned.
NUM upsEventTime_eighth	1.3.6.1.4.1.818.1.1.18.10.6.1.4	NonNegativeInteger32	read-only	The timestamp of the moment the event was generated.
NUM upsParametersRead_eighth	1.3.6.1.4.1.818.1.1.18.10.7	PositiveInteger32	read-write	The number of parameters to retreive from the UPS. When this object is set the ParameterTable will be filled with the requested number of entries. The value upsParametersStartAddress will be used as the start value of the table with the lowest index number.
NUM upsParametersWrite_eighth	1.3.6.1.4.1.818.1.1.18.10.8	PositiveInteger32	read-write	The number of parameters to write to the UPS. When this object is set the ParameterTable will be send to the ups. The value upsParametersStartAddress will be used for the first value of the table with the lowest index number.
NUM upsParametersStartAddress_eighth	1.3.6.1.4.1.818.1.1.18.10.9	NonNegativeInteger32	read-write	The address which is used as starting point for downloading parameters from the UPS
NUM upsParameterTableSize_eighth	1.3.6.1.4.1.818.1.1.18.10.10	NonNegativeInteger32	read-only	The number of entries in the parameter table. This object indicates the number of rows in the parameter table.
upsParameterTable_eighth	1.3.6.1.4.1.818.1.1.18.10.11		not-accessible	A list of parameter entries. The number of entries is always 16, and the value of upsParameterTableSize gives the number of valid entries from the begging of the table. Invalid entries return 0. To prevent problems with simultaneous queries from several agents, these values MUST be accessed using several PDUs in the same SNMP message ( is (1..16)): Read sequence: PDU-SET upsSetStartingAddress PDU-SET upsParametersRead PDU-GET upsParameterTableSize PDU-GET upsParameterValue 1 PDU-GET upsParameterValue 2 .. PDU-GET upsParameterValue The table is read up to requested number of events and the management software afterwards decides which entries are valid, as indicated by the upsParameterTableSize. Write sequence: PDU-SET upsSetStartingAddress PDU-SET upsParameterValue 1 PDU-SET upsParameterValue 2 .. PDU-SET upsParameterValue PDU-SET upsParametersWrite
upsParameterEntry_eighth	1.3.6.1.4.1.818.1.1.18.10.11.1		not-accessible	An entry containing information applicable to a particular parameter.
NUM upsParameterLineIndex_eighth	1.3.6.1.4.1.818.1.1.18.10.11.1.1	PositiveInteger32	not-accessible	The parameter line identifier.
I32 upsParameterValue_eighth	1.3.6.1.4.1.818.1.1.18.10.11.1.2	Integer32	read-write	The parameter value in numerical format.
NUM upsStatus_eighth	1.3.6.1.4.1.818.1.1.18.10.12	NonNegativeInteger32	read-only	The global UPS status is returned. Every bit reflects a specific status condition. Unused bits returns as 0. The status value can also be found on other commands. The value SNMP-NOSUCHNAME means 'invalid status' or 'status value non available'. Status 1 0001h upsStatusEcomodeIsOn 2 0002h upsStatusBatteryIsCharging 4 0004h upsStatusBatteryIsDischarging 8 0008h upsStatusAlarmIsActive 16 0010h upsStatusRectifierIsOn 32 0020h upsStatusLowBattery 64 0040h upsStatusOnBypass 128 0080h upsStatusMainsBypassOK 256 0100h upsStatusMainsRectifierOK 512 0200h upsStatusDetourIsOn 1024 0400h upsStatusAcousticAlarmIsOn 2048 0800h - (not used.) 4096 1000h upsStatusInverterIsOn 8192 2000h upsStatusNotInParallel (Q1 open) 16384 4000h upsStatusResetLoadOff 32768 8000h upsStatusLoadOff
NUM upsMainsStatisticsMBfail_eighth	1.3.6.1.4.1.818.1.1.18.10.13	NonNegativeInteger32	read-only	Count of main bypass failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsMRfail_eighth	1.3.6.1.4.1.818.1.1.18.10.14	NonNegativeInteger32	read-only	Count of mains rectifier failures (>200 ms), since UPS installation.
NUM upsMainsStatisticsB2_eighth	1.3.6.1.4.1.818.1.1.18.10.15	NonNegativeInteger32	read-only	Count of transients on the mains bypass (0..2 ms), during the last 7 days.
NUM upsMainsStatisticsB5_eighth	1.3.6.1.4.1.818.1.1.18.10.16	NonNegativeInteger32	read-only	Count of transients on the mains bypass (2..5 ms), during the last 7 days.
NUM upsMainsStatisticsB10_eighth	1.3.6.1.4.1.818.1.1.18.10.17	NonNegativeInteger32	read-only	Count of transients on the mains bypass (5..10 ms), during the last 7 days.
NUM upsMainsStatisticsB200_eighth	1.3.6.1.4.1.818.1.1.18.10.18	NonNegativeInteger32	read-only	Count of transients on the mains bypass (10..200 ms), during the last 7 days.
NUM upsMainsStatisticsBypRel_eighth	1.3.6.1.4.1.818.1.1.18.10.19	NonNegativeInteger32	read-only	Bypass reliability degree [0..100%;255]. The value NOSUCHNAME means 'not available'.
NUM upsTime_eighth	1.3.6.1.4.1.818.1.1.18.10.20	NonNegativeInteger32	read-write	The current timestamp (or real-time) of the UPS. For the format, see 'Timestamp' specifications. The write-command has to comply with the correct timestamp format expected by the UPS (counter value or real-time-clock value). Missing to doing so will result in a SNMP-eighthERROR, meaning 'command not supported'. It is possible to know which is the timestamp format supported by the UPS, by issuing a read-command or by reading events, which includes timestamps.
STR upsRequestPermission_eighth	1.3.6.1.4.1.818.1.1.18.10.21	DisplayString	write-only	An encrypted code is send to enable use of restricted write objects during a limited period of time.
I32 upsEventGetCode_eighth	1.3.6.1.4.1.818.1.1.18.10.22	Integer32	write-only	The code which is used as starting point to downloading the events from the UPS event buffer.
TES upsEventSpinLock_eighth	1.3.6.1.4.1.818.1.1.18.10.23	TestAndIncr	read-write	A spin lock on the event subsystem.
TES upsParameterSpinLock_eighth	1.3.6.1.4.1.818.1.1.18.10.24	TestAndIncr	read-write	A spin lock on the parameters subsystem.
geUPSTraps_eighth	1.3.6.1.4.1.818.1.1.18.11
NTF upsAlarmBatteryBadTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.1			One or more batteries have been determined to require replacement.
NTF upsAlarmOnBatteryTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.2			An On Battery condition is restored.
NTF upsAlarmLowBatteryTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.3			The remaining battery run-time is less than or equal to upsConfigLowBattTime.
NTF upsAlarmDepletedBatteryTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.4			The UPS will be unable to sustain the present load when and if the utility power is lost)
NTF upsAlarmTempBadTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.5			A temperature is out of tolerance.
NTF upsAlarmInputBadTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.6			An input condition is out of tolerance.
NTF upsAlarmOutputBadTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.7			An output condition (other than OutputOverload) is out of tolerance.
NTF upsAlarmOutputOverloadTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.8			The output load exceeds the UPS output capacity.
NTF upsAlarmOnBypassTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.9			The Bypass is presently engaged on the UPS.
NTF upsAlarmBypassBadTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.10			The Bypass is out of tolerance.
NTF upsAlarmOutputOffAsRequestedTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.11			The UPS has shutdown as requested, i.e., the output is off.
NTF upsAlarmUpsOffAsRequestedTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.12			The entire UPS has shutdown as commanded.
NTF upsAlarmChargerFailedTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.13			An uncorrected problem has been detected within the UPS charger subsystem.
NTF upsAlarmUpsOutputOffTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.14			The output of the UPS is in the off state.
NTF upsAlarmUpsSystemOffTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.15			The UPS system is in the off state.
NTF upsAlarmFanFailureTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.16			The failure of one or more fans in the UPS has been detected.
NTF upsAlarmFuseFailureTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.17			The failure of one or more fuses has been detected.
NTF upsAlarmGeneralFaultTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.18			A general fault in the UPS has been detected.
NTF upsAlarmDiagnosticTestFailedTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.19			The result of the last diagnostic test indicates a failure.
NTF upsAlarmCommunicationsLostTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.20			A problem has been encountered in the communication between the agent and the UPS.
NTF upsAlarmAwaitingPowerTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.21			The UPS output is off and the UPS is awaiting the return of the input power (*).
NTF upsAlarmShutdownPendingTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.22			A upsShutdownAfterDelay countdown is underway.
NTF upsAlarmShutdownImminentTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.23			The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
NTF upsAlarmTestInProgressTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.24			A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.
NTF upsAlarmReceptacleOffTrap_eighth	1.3.6.1.4.1.818.1.1.18.11.0.25			A receptacle has been switched off.
NTF upsAlarmBatteryBadRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.33			A Battery bad condition is restored.
NTF upsAlarmOnBatteryRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.34			The UPS is drawing power from mains again.
NTF upsAlarmLowBatteryRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.35			A Low Battery condition is restored.
NTF upsAlarmDepletedBatteryRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.36			A Depleted Battery condition is restored.
NTF upsAlarmTempBadRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.37			A bad temperature condition is restored.
NTF upsAlarmInputBadRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.38			An input bad condition is restored.
NTF upsAlarmOutputBadRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.39			An output bad condition is restored.
NTF upsAlarmOutputOverloadRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.40			An output overload condition is restored.
NTF upsAlarmOnBypassRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.41			An On Bypass condition is restored.
NTF upsAlarmBypassBadRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.42			A Bypass bad condition is restored.
NTF upsAlarmOutputOffAsRequestedRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.43			A request shutdown has been restored.
NTF upsAlarmUpsOffAsRequestedRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.44			A entire UPS command has been restored.
NTF upsAlarmChargerFailedRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.45			A Charger Failer condition is restored.
NTF upsAlarmUpsOutputOn_eighth	1.3.6.1.4.1.818.1.1.18.11.0.46			The output of the UPS switched in the on state.
NTF upsAlarmUpsSystemOn_eighth	1.3.6.1.4.1.818.1.1.18.11.0.47			The UPS system is switched in the on state.
NTF upsAlarmFanFailureRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.48			A Fan failure condition is restored.
NTF upsAlarmFuseFailureRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.49			A Fuse failure condition is restored.
NTF upsAlarmGeneralFaultRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.50			A general fault is restored.
NTF upsAlarmDiagnosticTestFailedRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.51			A last diagnostic test indicates a failure is restored.
NTF upsAlarmCommunicationsLostRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.52			A problem in the communication between the agent and the UPS is restored.
NTF upsAlarmAwaitingPowerRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.53			A awaiting power condition is restored (*).
NTF upsAlarmShutdownPendingRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.54			A upsShutdownAfterDelay countdown is restored.
NTF upsAlarmShutdownImminentRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.55			A shutdown imminent condition is restored.
NTF upsAlarmTestInProgressRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.56			The test is in progress is terminated.
NTF upsAlarmReceptacleOn_eighth	1.3.6.1.4.1.818.1.1.18.11.0.57			A receptacle has been switched on.
NTF upsAlarmValueLow_eighth	1.3.6.1.4.1.818.1.1.18.11.0.129			A measurement value reached a value below its low-level threshold.
NTF upsAlarmValueHigh_eighth	1.3.6.1.4.1.818.1.1.18.11.0.130			A measurement value reached a value higher than its high-level threshold.
NTF upsAlarmValueLowRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.133			A ValueLow alarm condition is restored.
NTF upsAlarmValueHighRestored_eighth	1.3.6.1.4.1.818.1.1.18.11.0.134			A ValueHigh alarm condition is restored.
geEnvironmental	1.3.6.1.4.1.818.1.2
ioInterface_First	1.3.6.1.4.1.818.1.2.1
ioInterfaceInputLine_First	1.3.6.1.4.1.818.1.2.1.1
NUM ioInterfaceNumInputs_First	1.3.6.1.4.1.818.1.2.1.1.1	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
ioInterfaceInputTable_First	1.3.6.1.4.1.818.1.2.1.1.2		not-accessible	A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
ioInterfaceInputEntry_First	1.3.6.1.4.1.818.1.2.1.1.2.1		not-accessible	An entry containing information applicable to a particular input line.
NUM ioInterfaceInputLineIndex_First	1.3.6.1.4.1.818.1.2.1.1.2.1.1	PositiveInteger32	not-accessible	The input line identifier.
STR ioInterfaceInputDescription_First	1.3.6.1.4.1.818.1.2.1.1.2.1.2	DisplayString	read-write	A description of the alarm monitored by this input line.
INT ioInterfaceInputStatus_First	1.3.6.1.4.1.818.1.2.1.1.2.1.3	INTEGER	read-only	The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
INT ioInterfaceEdgeMode_First	1.3.6.1.4.1.818.1.2.1.1.2.1.4	INTEGER	read-write	Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
INT ioInterfaceAlarmMask_First	1.3.6.1.4.1.818.1.2.1.1.2.1.5	INTEGER	read-write	Alarm functionality for the input line can be set active or inactive.
NUM ioInterfaceAlarmDelay_First	1.3.6.1.4.1.818.1.2.1.1.3	NonNegativeInteger32	read-write	Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
ioInterfaceOutputLine_First	1.3.6.1.4.1.818.1.2.1.2
NUM ioInterfaceNumOutput_First	1.3.6.1.4.1.818.1.2.1.2.1	NonNegativeInteger32	read-only	The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
ioInterfaceOutputTable_First	1.3.6.1.4.1.818.1.2.1.2.2		not-accessible	A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
ioInterfaceOutputEntry_First	1.3.6.1.4.1.818.1.2.1.2.2.1		not-accessible	An entry containing information applicable to a particular output line.
NUM ioInterfaceOutputLineIndex_First	1.3.6.1.4.1.818.1.2.1.2.2.1.1	PositiveInteger32	not-accessible	The output line identifier.
STR ioInterfaceOutputDescription_First	1.3.6.1.4.1.818.1.2.1.2.2.1.2	DisplayString	read-write	A description of the alarm monitored by this output line.
INT ioInterfaceOutputStatus_First	1.3.6.1.4.1.818.1.2.1.2.2.1.3	INTEGER	read-write	The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
ioInterfaceAnalogueLine_First	1.3.6.1.4.1.818.1.2.1.3
NUM ioInterfaceNumAnalogue_First	1.3.6.1.4.1.818.1.2.1.3.1	NonNegativeInteger32	read-only	The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
ioInterfaceAnalogueTable_First	1.3.6.1.4.1.818.1.2.1.3.2		not-accessible	A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
ioInterfaceAnalogueEntry_First	1.3.6.1.4.1.818.1.2.1.3.2.1		not-accessible	An entry containing information applicable to a particular analogue line.
NUM ioInterfaceAnalogueLineIndex_First	1.3.6.1.4.1.818.1.2.1.3.2.1.1	PositiveInteger32	not-accessible	The analogue line identifier.
STR ioInterfaceAnalogueDescription_First	1.3.6.1.4.1.818.1.2.1.3.2.1.2	DisplayString	read-write	A description of the alarm monitored by this analogue line.
I32 ioInterfaceAnalogueStatus_First	1.3.6.1.4.1.818.1.2.1.3.2.1.3	Integer32	read-only	Read analogue value 1, when the board support such functionality
I32 ioInterfaceAnalogueLowThreshold_First	1.3.6.1.4.1.818.1.2.1.3.2.1.4	Integer32	read-write	Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueHighThreshold_First	1.3.6.1.4.1.818.1.2.1.3.2.1.5	Integer32	read-write	High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueResetLowThreshold_First	1.3.6.1.4.1.818.1.2.1.3.2.1.6	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
I32 ioInterfaceAnalogueResetHighThreshold_First	1.3.6.1.4.1.818.1.2.1.3.2.1.7	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
ioInterfaceTraps_First	1.3.6.1.4.1.818.1.2.1.4
NTF ioAlarmGenericChange_First	1.3.6.1.4.1.818.1.2.1.4.0.1			An generic change of a digital input/digital output/analog input has become active.
ioInterface_Second	1.3.6.1.4.1.818.1.2.2
ioInterfaceInputLine_Second	1.3.6.1.4.1.818.1.2.2.1
NUM ioInterfaceNumInputs_Second	1.3.6.1.4.1.818.1.2.2.1.1	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
ioInterfaceInputTable_Second	1.3.6.1.4.1.818.1.2.2.1.2		not-accessible	A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
ioInterfaceInputEntry_Second	1.3.6.1.4.1.818.1.2.2.1.2.1		not-accessible	An entry containing information applicable to a particular input line.
NUM ioInterfaceInputLineIndex_Second	1.3.6.1.4.1.818.1.2.2.1.2.1.1	PositiveInteger32	not-accessible	The input line identifier.
STR ioInterfaceInputDescription_Second	1.3.6.1.4.1.818.1.2.2.1.2.1.2	DisplayString	read-write	A description of the alarm monitored by this input line.
INT ioInterfaceInputStatus_Second	1.3.6.1.4.1.818.1.2.2.1.2.1.3	INTEGER	read-only	The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
INT ioInterfaceEdgeMode_Second	1.3.6.1.4.1.818.1.2.2.1.2.1.4	INTEGER	read-write	Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
INT ioInterfaceAlarmMask_Second	1.3.6.1.4.1.818.1.2.2.1.2.1.5	INTEGER	read-write	Alarm functionality for the input line can be set active or inactive.
NUM ioInterfaceAlarmDelay_Second	1.3.6.1.4.1.818.1.2.2.1.2.1.6	NonNegativeInteger32	read-write	Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
ioInterfaceOutputLine_Second	1.3.6.1.4.1.818.1.2.2.2
NUM ioInterfaceNumOutput_Second	1.3.6.1.4.1.818.1.2.2.2.1	NonNegativeInteger32	read-only	The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
ioInterfaceOutputTable_Second	1.3.6.1.4.1.818.1.2.2.2.2		not-accessible	A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
ioInterfaceOutputEntry_Second	1.3.6.1.4.1.818.1.2.2.2.2.1		not-accessible	An entry containing information applicable to a particular output line.
NUM ioInterfaceOutputLineIndex_Second	1.3.6.1.4.1.818.1.2.2.2.2.1.1	PositiveInteger32	not-accessible	The output line identifier.
STR ioInterfaceOutputDescription_Second	1.3.6.1.4.1.818.1.2.2.2.2.1.2	DisplayString	read-write	A description of the alarm monitored by this output line.
INT ioInterfaceOutputStatus_Second	1.3.6.1.4.1.818.1.2.2.2.2.1.3	INTEGER	read-write	The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
ioInterfaceAnalogueLine_Second	1.3.6.1.4.1.818.1.2.2.3
NUM ioInterfaceNumAnalogue_Second	1.3.6.1.4.1.818.1.2.2.3.1	NonNegativeInteger32	read-only	The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
ioInterfaceAnalogueTable_Second	1.3.6.1.4.1.818.1.2.2.3.2		not-accessible	A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
ioInterfaceAnalogueEntry_Second	1.3.6.1.4.1.818.1.2.2.3.2.1		not-accessible	An entry containing information applicable to a particular analogue line.
NUM ioInterfaceAnalogueLineIndex_Second	1.3.6.1.4.1.818.1.2.2.3.2.1.1	PositiveInteger32	not-accessible	The analogue line identifier.
STR ioInterfaceAnalogueDescription_Second	1.3.6.1.4.1.818.1.2.2.3.2.1.2	DisplayString	read-write	A description of the alarm monitored by this analogue line.
I32 ioInterfaceAnalogueStatus_Second	1.3.6.1.4.1.818.1.2.2.3.2.1.3	Integer32	read-only	Read analogue value 1, when the board support such functionality
I32 ioInterfaceAnalogueLowThreshold_Second	1.3.6.1.4.1.818.1.2.2.3.2.1.4	Integer32	read-write	Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueHighThreshold_Second	1.3.6.1.4.1.818.1.2.2.3.2.1.5	Integer32	read-write	High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueResetLowThreshold_Second	1.3.6.1.4.1.818.1.2.2.3.2.1.6	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
I32 ioInterfaceAnalogueResetHighThreshold_Second	1.3.6.1.4.1.818.1.2.2.3.2.1.7	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
ioInterfaceTraps_Second	1.3.6.1.4.1.818.1.2.2.4
NTF ioAlarmGenericChange_Second	1.3.6.1.4.1.818.1.2.2.4.0.1			An generic change of a digital input/digital output/analog input has become active.
ioInterface_Third	1.3.6.1.4.1.818.1.2.3
ioInterfaceInputLine_Third	1.3.6.1.4.1.818.1.2.3.1
NUM ioInterfaceNumInputs_Third	1.3.6.1.4.1.818.1.2.3.1.1	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
ioInterfaceInputTable_Third	1.3.6.1.4.1.818.1.2.3.1.2		not-accessible	A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
ioInterfaceInputEntry_Third	1.3.6.1.4.1.818.1.2.3.1.2.1		not-accessible	An entry containing information applicable to a particular input line.
NUM ioInterfaceInputLineIndex_Third	1.3.6.1.4.1.818.1.2.3.1.2.1.1	PositiveInteger32	not-accessible	The input line identifier.
STR ioInterfaceInputDescription_Third	1.3.6.1.4.1.818.1.2.3.1.2.1.2	DisplayString	read-write	A description of the alarm monitored by this input line.
INT ioInterfaceInputStatus_Third	1.3.6.1.4.1.818.1.2.3.1.2.1.3	INTEGER	read-only	The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
INT ioInterfaceEdgeMode_Third	1.3.6.1.4.1.818.1.2.3.1.2.1.4	INTEGER	read-write	Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
INT ioInterfaceAlarmMask_Third	1.3.6.1.4.1.818.1.2.3.1.2.1.5	INTEGER	read-write	Alarm functionality for the input line can be set active or inactive.
NUM ioInterfaceAlarmDelay_Third	1.3.6.1.4.1.818.1.2.3.1.2.1.6	NonNegativeInteger32	read-write	Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
ioInterfaceOutputLine_Third	1.3.6.1.4.1.818.1.2.3.2
NUM ioInterfaceNumOutput_Third	1.3.6.1.4.1.818.1.2.3.2.1	NonNegativeInteger32	read-only	The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
ioInterfaceOutputTable_Third	1.3.6.1.4.1.818.1.2.3.2.2		not-accessible	A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
ioInterfaceOutputEntry_Third	1.3.6.1.4.1.818.1.2.3.2.2.1		not-accessible	An entry containing information applicable to a particular output line.
NUM ioInterfaceOutputLineIndex_Third	1.3.6.1.4.1.818.1.2.3.2.2.1.1	PositiveInteger32	not-accessible	The output line identifier.
STR ioInterfaceOutputDescription_Third	1.3.6.1.4.1.818.1.2.3.2.2.1.2	DisplayString	read-write	A description of the alarm monitored by this output line.
INT ioInterfaceOutputStatus_Third	1.3.6.1.4.1.818.1.2.3.2.2.1.3	INTEGER	read-write	The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
ioInterfaceAnalogueLine_Third	1.3.6.1.4.1.818.1.2.3.3
NUM ioInterfaceNumAnalogue_Third	1.3.6.1.4.1.818.1.2.3.3.1	NonNegativeInteger32	read-only	The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
ioInterfaceAnalogueTable_Third	1.3.6.1.4.1.818.1.2.3.3.2		not-accessible	A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
ioInterfaceAnalogueEntry_Third	1.3.6.1.4.1.818.1.2.3.3.2.1		not-accessible	An entry containing information applicable to a particular analogue line.
NUM ioInterfaceAnalogueLineIndex_Third	1.3.6.1.4.1.818.1.2.3.3.2.1.1	PositiveInteger32	not-accessible	The analogue line identifier.
STR ioInterfaceAnalogueDescription_Third	1.3.6.1.4.1.818.1.2.3.3.2.1.2	DisplayString	read-write	A description of the alarm monitored by this analogue line.
I32 ioInterfaceAnalogueStatus_Third	1.3.6.1.4.1.818.1.2.3.3.2.1.3	Integer32	read-only	Read analogue value 1, when the board support such functionality
I32 ioInterfaceAnalogueLowThreshold_Third	1.3.6.1.4.1.818.1.2.3.3.2.1.4	Integer32	read-write	Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueHighThreshold_Third	1.3.6.1.4.1.818.1.2.3.3.2.1.5	Integer32	read-write	High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueResetLowThreshold_Third	1.3.6.1.4.1.818.1.2.3.3.2.1.6	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
I32 ioInterfaceAnalogueResetHighThreshold_Third	1.3.6.1.4.1.818.1.2.3.3.2.1.7	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
ioInterfaceTraps_Third	1.3.6.1.4.1.818.1.2.3.4
NTF ioAlarmGenericChange_Third	1.3.6.1.4.1.818.1.2.3.4.0.1			An generic change of a digital input/digital output/analog input has become active.
ioInterface_Fourth	1.3.6.1.4.1.818.1.2.4
ioInterfaceInputLine_Fourth	1.3.6.1.4.1.818.1.2.4.1
NUM ioInterfaceNumInputs_Fourth	1.3.6.1.4.1.818.1.2.4.1.1	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
ioInterfaceInputTable_Fourth	1.3.6.1.4.1.818.1.2.4.1.2		not-accessible	A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
ioInterfaceInputEntry_Fourth	1.3.6.1.4.1.818.1.2.4.1.2.1		not-accessible	An entry containing information applicable to a particular input line.
NUM ioInterfaceInputLineIndex_Fourth	1.3.6.1.4.1.818.1.2.4.1.2.1.1	PositiveInteger32	not-accessible	The input line identifier.
STR ioInterfaceInputDescription_Fourth	1.3.6.1.4.1.818.1.2.4.1.2.1.2	DisplayString	read-write	A description of the alarm monitored by this input line.
INT ioInterfaceInputStatus_Fourth	1.3.6.1.4.1.818.1.2.4.1.2.1.3	INTEGER	read-only	The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
INT ioInterfaceEdgeMode_Fourth	1.3.6.1.4.1.818.1.2.4.1.2.1.4	INTEGER	read-write	Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
INT ioInterfaceAlarmMask_Fourth	1.3.6.1.4.1.818.1.2.4.1.2.1.5	INTEGER	read-write	Alarm functionality for the input line can be set active or inactive.
NUM ioInterfaceAlarmDelay_Fourth	1.3.6.1.4.1.818.1.2.4.1.2.1.6	NonNegativeInteger32	read-write	Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
ioInterfaceOutputLine_Fourth	1.3.6.1.4.1.818.1.2.4.2
NUM ioInterfaceNumOutput_Fourth	1.3.6.1.4.1.818.1.2.4.2.1	NonNegativeInteger32	read-only	The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
ioInterfaceOutputTable_Fourth	1.3.6.1.4.1.818.1.2.4.2.2		not-accessible	A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
ioInterfaceOutputEntry_Fourth	1.3.6.1.4.1.818.1.2.4.2.2.1		not-accessible	An entry containing information applicable to a particular output line.
NUM ioInterfaceOutputLineIndex_Fourth	1.3.6.1.4.1.818.1.2.4.2.2.1.1	PositiveInteger32	not-accessible	The output line identifier.
STR ioInterfaceOutputDescription_Fourth	1.3.6.1.4.1.818.1.2.4.2.2.1.2	DisplayString	read-write	A description of the alarm monitored by this output line.
INT ioInterfaceOutputStatus_Fourth	1.3.6.1.4.1.818.1.2.4.2.2.1.3	INTEGER	read-write	The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
ioInterfaceAnalogueLine_Fourth	1.3.6.1.4.1.818.1.2.4.3
NUM ioInterfaceNumAnalogue_Fourth	1.3.6.1.4.1.818.1.2.4.3.1	NonNegativeInteger32	read-only	The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
ioInterfaceAnalogueTable_Fourth	1.3.6.1.4.1.818.1.2.4.3.2		not-accessible	A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
ioInterfaceAnalogueEntry_Fourth	1.3.6.1.4.1.818.1.2.4.3.2.1		not-accessible	An entry containing information applicable to a particular analogue line.
NUM ioInterfaceAnalogueLineIndex_Fourth	1.3.6.1.4.1.818.1.2.4.3.2.1.1	PositiveInteger32	not-accessible	The analogue line identifier.
STR ioInterfaceAnalogueDescription_Fourth	1.3.6.1.4.1.818.1.2.4.3.2.1.2	DisplayString	read-write	A description of the alarm monitored by this analogue line.
I32 ioInterfaceAnalogueStatus_Fourth	1.3.6.1.4.1.818.1.2.4.3.2.1.3	Integer32	read-only	Read analogue value 1, when the board support such functionality
I32 ioInterfaceAnalogueLowThreshold_Fourth	1.3.6.1.4.1.818.1.2.4.3.2.1.4	Integer32	read-write	Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueHighThreshold_Fourth	1.3.6.1.4.1.818.1.2.4.3.2.1.5	Integer32	read-write	High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueResetLowThreshold_Fourth	1.3.6.1.4.1.818.1.2.4.3.2.1.6	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
I32 ioInterfaceAnalogueResetHighThreshold_Fourth	1.3.6.1.4.1.818.1.2.4.3.2.1.7	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
ioInterfaceTraps_Fourth	1.3.6.1.4.1.818.1.2.4.4
NTF ioAlarmGenericChange_Fourth	1.3.6.1.4.1.818.1.2.4.4.0.1			An generic change of a digital input/digital output/analog input has become active.
ioInterface_Fifth	1.3.6.1.4.1.818.1.2.5
ioInterfaceInputLine_Fifth	1.3.6.1.4.1.818.1.2.5.1
NUM ioInterfaceNumInputs_Fifth	1.3.6.1.4.1.818.1.2.5.1.1	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
ioInterfaceInputTable_Fifth	1.3.6.1.4.1.818.1.2.5.1.2		not-accessible	A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
ioInterfaceInputEntry_Fifth	1.3.6.1.4.1.818.1.2.5.1.2.1		not-accessible	An entry containing information applicable to a particular input line.
NUM ioInterfaceInputLineIndex_Fifth	1.3.6.1.4.1.818.1.2.5.1.2.1.1	PositiveInteger32	not-accessible	The input line identifier.
STR ioInterfaceInputDescription_Fifth	1.3.6.1.4.1.818.1.2.5.1.2.1.2	DisplayString	read-write	A description of the alarm monitored by this input line.
INT ioInterfaceInputStatus_Fifth	1.3.6.1.4.1.818.1.2.5.1.2.1.3	INTEGER	read-only	The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
INT ioInterfaceEdgeMode_Fifth	1.3.6.1.4.1.818.1.2.5.1.2.1.4	INTEGER	read-write	Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
INT ioInterfaceAlarmMask_Fifth	1.3.6.1.4.1.818.1.2.5.1.2.1.5	INTEGER	read-write	Alarm functionality for the input line can be set active or inactive.
NUM ioInterfaceAlarmDelay_Fifth	1.3.6.1.4.1.818.1.2.5.1.2.1.6	NonNegativeInteger32	read-write	Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
ioInterfaceOutputLine_Fifth	1.3.6.1.4.1.818.1.2.5.2
NUM ioInterfaceNumOutput_Fifth	1.3.6.1.4.1.818.1.2.5.2.1	NonNegativeInteger32	read-only	The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
ioInterfaceOutputTable_Fifth	1.3.6.1.4.1.818.1.2.5.2.2		not-accessible	A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
ioInterfaceOutputEntry_Fifth	1.3.6.1.4.1.818.1.2.5.2.2.1		not-accessible	An entry containing information applicable to a particular output line.
NUM ioInterfaceOutputLineIndex_Fifth	1.3.6.1.4.1.818.1.2.5.2.2.1.1	PositiveInteger32	not-accessible	The output line identifier.
STR ioInterfaceOutputDescription_Fifth	1.3.6.1.4.1.818.1.2.5.2.2.1.2	DisplayString	read-write	A description of the alarm monitored by this output line.
INT ioInterfaceOutputStatus_Fifth	1.3.6.1.4.1.818.1.2.5.2.2.1.3	INTEGER	read-write	The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
ioInterfaceAnalogueLine_Fifth	1.3.6.1.4.1.818.1.2.5.3
NUM ioInterfaceNumAnalogue_Fifth	1.3.6.1.4.1.818.1.2.5.3.1	NonNegativeInteger32	read-only	The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
ioInterfaceAnalogueTable_Fifth	1.3.6.1.4.1.818.1.2.5.3.2		not-accessible	A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
ioInterfaceAnalogueEntry_Fifth	1.3.6.1.4.1.818.1.2.5.3.2.1		not-accessible	An entry containing information applicable to a particular analogue line.
NUM ioInterfaceAnalogueLineIndex_Fifth	1.3.6.1.4.1.818.1.2.5.3.2.1.1	PositiveInteger32	not-accessible	The analogue line identifier.
STR ioInterfaceAnalogueDescription_Fifth	1.3.6.1.4.1.818.1.2.5.3.2.1.2	DisplayString	read-write	A description of the alarm monitored by this analogue line.
I32 ioInterfaceAnalogueStatus_Fifth	1.3.6.1.4.1.818.1.2.5.3.2.1.3	Integer32	read-only	Read analogue value 1, when the board support such functionality
I32 ioInterfaceAnalogueLowThreshold_Fifth	1.3.6.1.4.1.818.1.2.5.3.2.1.4	Integer32	read-write	Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueHighThreshold_Fifth	1.3.6.1.4.1.818.1.2.5.3.2.1.5	Integer32	read-write	High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueResetLowThreshold_Fifth	1.3.6.1.4.1.818.1.2.5.3.2.1.6	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
I32 ioInterfaceAnalogueResetHighThreshold_Fifth	1.3.6.1.4.1.818.1.2.5.3.2.1.7	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
ioInterfaceTraps_Fifth	1.3.6.1.4.1.818.1.2.5.4
NTF ioAlarmGenericChange_Fifth	1.3.6.1.4.1.818.1.2.5.4.0.1			An generic change of a digital input/digital output/analog input has become active.
ioInterface_Sixth	1.3.6.1.4.1.818.1.2.6
ioInterfaceInputLine_Sixth	1.3.6.1.4.1.818.1.2.6.1
NUM ioInterfaceNumInputs_Sixth	1.3.6.1.4.1.818.1.2.6.1.1	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
ioInterfaceInputTable_Sixth	1.3.6.1.4.1.818.1.2.6.1.2		not-accessible	A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
ioInterfaceInputEntry_Sixth	1.3.6.1.4.1.818.1.2.6.1.2.1		not-accessible	An entry containing information applicable to a particular input line.
NUM ioInterfaceInputLineIndex_Sixth	1.3.6.1.4.1.818.1.2.6.1.2.1.1	PositiveInteger32	not-accessible	The input line identifier.
STR ioInterfaceInputDescription_Sixth	1.3.6.1.4.1.818.1.2.6.1.2.1.2	DisplayString	read-write	A description of the alarm monitored by this input line.
INT ioInterfaceInputStatus_Sixth	1.3.6.1.4.1.818.1.2.6.1.2.1.3	INTEGER	read-only	The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
INT ioInterfaceEdgeMode_Sixth	1.3.6.1.4.1.818.1.2.6.1.2.1.4	INTEGER	read-write	Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
INT ioInterfaceAlarmMask_Sixth	1.3.6.1.4.1.818.1.2.6.1.2.1.5	INTEGER	read-write	Alarm functionality for the input line can be set active or inactive.
NUM ioInterfaceAlarmDelay_Sixth	1.3.6.1.4.1.818.1.2.6.1.2.1.6	NonNegativeInteger32	read-write	Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
ioInterfaceOutputLine_Sixth	1.3.6.1.4.1.818.1.2.6.2
NUM ioInterfaceNumOutput_Sixth	1.3.6.1.4.1.818.1.2.6.2.1	NonNegativeInteger32	read-only	The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
ioInterfaceOutputTable_Sixth	1.3.6.1.4.1.818.1.2.6.2.2		not-accessible	A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
ioInterfaceOutputEntry_Sixth	1.3.6.1.4.1.818.1.2.6.2.2.1		not-accessible	An entry containing information applicable to a particular output line.
NUM ioInterfaceOutputLineIndex_Sixth	1.3.6.1.4.1.818.1.2.6.2.2.1.1	PositiveInteger32	not-accessible	The output line identifier.
STR ioInterfaceOutputDescription_Sixth	1.3.6.1.4.1.818.1.2.6.2.2.1.2	DisplayString	read-write	A description of the alarm monitored by this output line.
INT ioInterfaceOutputStatus_Sixth	1.3.6.1.4.1.818.1.2.6.2.2.1.3	INTEGER	read-write	The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
ioInterfaceAnalogueLine_Sixth	1.3.6.1.4.1.818.1.2.6.3
NUM ioInterfaceNumAnalogue_Sixth	1.3.6.1.4.1.818.1.2.6.3.1	NonNegativeInteger32	read-only	The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
ioInterfaceAnalogueTable_Sixth	1.3.6.1.4.1.818.1.2.6.3.2		not-accessible	A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
ioInterfaceAnalogueEntry_Sixth	1.3.6.1.4.1.818.1.2.6.3.2.1		not-accessible	An entry containing information applicable to a particular analogue line.
NUM ioInterfaceAnalogueLineIndex_Sixth	1.3.6.1.4.1.818.1.2.6.3.2.1.1	PositiveInteger32	not-accessible	The analogue line identifier.
STR ioInterfaceAnalogueDescription_Sixth	1.3.6.1.4.1.818.1.2.6.3.2.1.2	DisplayString	read-write	A description of the alarm monitored by this analogue line.
I32 ioInterfaceAnalogueStatus_Sixth	1.3.6.1.4.1.818.1.2.6.3.2.1.3	Integer32	read-only	Read analogue value 1, when the board support such functionality
I32 ioInterfaceAnalogueLowThreshold_Sixth	1.3.6.1.4.1.818.1.2.6.3.2.1.4	Integer32	read-write	Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueHighThreshold_Sixth	1.3.6.1.4.1.818.1.2.6.3.2.1.5	Integer32	read-write	High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueResetLowThreshold_Sixth	1.3.6.1.4.1.818.1.2.6.3.2.1.6	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
I32 ioInterfaceAnalogueResetHighThreshold_Sixth	1.3.6.1.4.1.818.1.2.6.3.2.1.7	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
ioInterfaceTraps_Sixth	1.3.6.1.4.1.818.1.2.6.4
NTF ioAlarmGenericChange_Sixth	1.3.6.1.4.1.818.1.2.6.4.0.1			An generic change of a digital input/digital output/analog input has become active.
ioInterface_Seventh	1.3.6.1.4.1.818.1.2.7
ioInterfaceInputLine_Seventh	1.3.6.1.4.1.818.1.2.7.1
NUM ioInterfaceNumInputs_Seventh	1.3.6.1.4.1.818.1.2.7.1.1	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
ioInterfaceInputTable_Seventh	1.3.6.1.4.1.818.1.2.7.1.2		not-accessible	A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
ioInterfaceInputEntry_Seventh	1.3.6.1.4.1.818.1.2.7.1.2.1		not-accessible	An entry containing information applicable to a particular input line.
NUM ioInterfaceInputLineIndex_Seventh	1.3.6.1.4.1.818.1.2.7.1.2.1.1	PositiveInteger32	not-accessible	The input line identifier.
STR ioInterfaceInputDescription_Seventh	1.3.6.1.4.1.818.1.2.7.1.2.1.2	DisplayString	read-write	A description of the alarm monitored by this input line.
INT ioInterfaceInputStatus_Seventh	1.3.6.1.4.1.818.1.2.7.1.2.1.3	INTEGER	read-only	The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
INT ioInterfaceEdgeMode_Seventh	1.3.6.1.4.1.818.1.2.7.1.2.1.4	INTEGER	read-write	Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
INT ioInterfaceAlarmMask_Seventh	1.3.6.1.4.1.818.1.2.7.1.2.1.5	INTEGER	read-write	Alarm functionality for the input line can be set active or inactive.
NUM ioInterfaceAlarmDelay_Seventh	1.3.6.1.4.1.818.1.2.7.1.2.1.6	NonNegativeInteger32	read-write	Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
ioInterfaceOutputLine_Seventh	1.3.6.1.4.1.818.1.2.7.2
NUM ioInterfaceNumOutput_Seventh	1.3.6.1.4.1.818.1.2.7.2.1	NonNegativeInteger32	read-only	The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
ioInterfaceOutputTable_Seventh	1.3.6.1.4.1.818.1.2.7.2.2		not-accessible	A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
ioInterfaceOutputEntry_Seventh	1.3.6.1.4.1.818.1.2.7.2.2.1		not-accessible	An entry containing information applicable to a particular output line.
NUM ioInterfaceOutputLineIndex_Seventh	1.3.6.1.4.1.818.1.2.7.2.2.1.1	PositiveInteger32	not-accessible	The output line identifier.
STR ioInterfaceOutputDescription_Seventh	1.3.6.1.4.1.818.1.2.7.2.2.1.2	DisplayString	read-write	A description of the alarm monitored by this output line.
INT ioInterfaceOutputStatus_Seventh	1.3.6.1.4.1.818.1.2.7.2.2.1.3	INTEGER	read-write	The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
ioInterfaceAnalogueLine_Seventh	1.3.6.1.4.1.818.1.2.7.3
NUM ioInterfaceNumAnalogue_Seventh	1.3.6.1.4.1.818.1.2.7.3.1	NonNegativeInteger32	read-only	The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
ioInterfaceAnalogueTable_Seventh	1.3.6.1.4.1.818.1.2.7.3.2		not-accessible	A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
ioInterfaceAnalogueEntry_Seventh	1.3.6.1.4.1.818.1.2.7.3.2.1		not-accessible	An entry containing information applicable to a particular analogue line.
NUM ioInterfaceAnalogueLineIndex_Seventh	1.3.6.1.4.1.818.1.2.7.3.2.1.1	PositiveInteger32	not-accessible	The analogue line identifier.
STR ioInterfaceAnalogueDescription_Seventh	1.3.6.1.4.1.818.1.2.7.3.2.1.2	DisplayString	read-write	A description of the alarm monitored by this analogue line.
I32 ioInterfaceAnalogueStatus_Seventh	1.3.6.1.4.1.818.1.2.7.3.2.1.3	Integer32	read-only	Read analogue value 1, when the board support such functionality
I32 ioInterfaceAnalogueLowThreshold_Seventh	1.3.6.1.4.1.818.1.2.7.3.2.1.4	Integer32	read-write	Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueHighThreshold_Seventh	1.3.6.1.4.1.818.1.2.7.3.2.1.5	Integer32	read-write	High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueResetLowThreshold_Seventh	1.3.6.1.4.1.818.1.2.7.3.2.1.6	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
I32 ioInterfaceAnalogueResetHighThreshold_Seventh	1.3.6.1.4.1.818.1.2.7.3.2.1.7	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
ioInterfaceTraps_Seventh	1.3.6.1.4.1.818.1.2.7.4
NTF ioAlarmGenericChange_Seventh	1.3.6.1.4.1.818.1.2.7.4.0.1			An generic change of a digital input/digital output/analog input has become active.
ioInterface_Eighth	1.3.6.1.4.1.818.1.2.8
ioInterfaceInputLine_Eighth	1.3.6.1.4.1.818.1.2.8.1
NUM ioInterfaceNumInputs_Eighth	1.3.6.1.4.1.818.1.2.8.1.1	NonNegativeInteger32	read-only	The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
ioInterfaceInputTable_Eighth	1.3.6.1.4.1.818.1.2.8.1.2		not-accessible	A list of input line table entries. The number of entries is given by the value of ioInterfaceNumInputs.
ioInterfaceInputEntry_Eighth	1.3.6.1.4.1.818.1.2.8.1.2.1		not-accessible	An entry containing information applicable to a particular input line.
NUM ioInterfaceInputLineIndex_Eighth	1.3.6.1.4.1.818.1.2.8.1.2.1.1	PositiveInteger32	not-accessible	The input line identifier.
STR ioInterfaceInputDescription_Eighth	1.3.6.1.4.1.818.1.2.8.1.2.1.2	DisplayString	read-write	A description of the alarm monitored by this input line.
INT ioInterfaceInputStatus_Eighth	1.3.6.1.4.1.818.1.2.8.1.2.1.3	INTEGER	read-only	The status of the input lines controlled by the device. When a bit is high (1), the associated line is 'active'
INT ioInterfaceEdgeMode_Eighth	1.3.6.1.4.1.818.1.2.8.1.2.1.4	INTEGER	read-write	Edge mode for input lines. This object specifies if the corresponding input line should be recognised immediately as active (edge mode on), or only when the state remains stable for at least the time specified by ioInterfaceAlarmDelay (edge mode off). EdgeMode is only meaningful when the object ioInterfaceAlarmMask is active.
INT ioInterfaceAlarmMask_Eighth	1.3.6.1.4.1.818.1.2.8.1.2.1.5	INTEGER	read-write	Alarm functionality for the input line can be set active or inactive.
NUM ioInterfaceAlarmDelay_Eighth	1.3.6.1.4.1.818.1.2.8.1.2.1.6	NonNegativeInteger32	read-write	Time delay during which an active input line has to be stable, prior to issue an alarm. Effective only when EdgeMode=off for the corresponding line.
ioInterfaceOutputLine_Eighth	1.3.6.1.4.1.818.1.2.8.2
NUM ioInterfaceNumOutput_Eighth	1.3.6.1.4.1.818.1.2.8.2.1	NonNegativeInteger32	read-only	The number of output lines utilized by this device. This entry indicates the number of rows in the output line table.
ioInterfaceOutputTable_Eighth	1.3.6.1.4.1.818.1.2.8.2.2		not-accessible	A list of output line table entries. The number of entries is given by the value of ioInterfaceNumOutputs.
ioInterfaceOutputEntry_Eighth	1.3.6.1.4.1.818.1.2.8.2.2.1		not-accessible	An entry containing information applicable to a particular output line.
NUM ioInterfaceOutputLineIndex_Eighth	1.3.6.1.4.1.818.1.2.8.2.2.1.1	PositiveInteger32	not-accessible	The output line identifier.
STR ioInterfaceOutputDescription_Eighth	1.3.6.1.4.1.818.1.2.8.2.2.1.2	DisplayString	read-write	A description of the alarm monitored by this output line.
INT ioInterfaceOutputStatus_Eighth	1.3.6.1.4.1.818.1.2.8.2.2.1.3	INTEGER	read-write	The status of the output lines controlled by the device. When a bit is high (1), the associated line is 'active'
ioInterfaceAnalogueLine_Eighth	1.3.6.1.4.1.818.1.2.8.3
NUM ioInterfaceNumAnalogue_Eighth	1.3.6.1.4.1.818.1.2.8.3.1	NonNegativeInteger32	read-only	The number of analogue lines utilized by this device. This entry indicates the number of rows in the analogue line table.
ioInterfaceAnalogueTable_Eighth	1.3.6.1.4.1.818.1.2.8.3.2		not-accessible	A list of analogue line table entries. The number of entries is given by the value of ioInterfaceNumAnalogue.
ioInterfaceAnalogueEntry_Eighth	1.3.6.1.4.1.818.1.2.8.3.2.1		not-accessible	An entry containing information applicable to a particular analogue line.
NUM ioInterfaceAnalogueLineIndex_Eighth	1.3.6.1.4.1.818.1.2.8.3.2.1.1	PositiveInteger32	not-accessible	The analogue line identifier.
STR ioInterfaceAnalogueDescription_Eighth	1.3.6.1.4.1.818.1.2.8.3.2.1.2	DisplayString	read-write	A description of the alarm monitored by this analogue line.
I32 ioInterfaceAnalogueStatus_Eighth	1.3.6.1.4.1.818.1.2.8.3.2.1.3	Integer32	read-only	Read analogue value 1, when the board support such functionality
I32 ioInterfaceAnalogueLowThreshold_Eighth	1.3.6.1.4.1.818.1.2.8.3.2.1.4	Integer32	read-write	Low limit for the analogical value. When the analogical measurement comes under this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueHighThreshold_Eighth	1.3.6.1.4.1.818.1.2.8.3.2.1.5	Integer32	read-write	High limit for the analogical value. When the analogical measurement comes higher than this limit, an alarm is issued. The limit can be disabled specifying the special floating point value which means 'not available'.
I32 ioInterfaceAnalogueResetLowThreshold_Eighth	1.3.6.1.4.1.818.1.2.8.3.2.1.6	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the low alarm condition (hysteresis)
I32 ioInterfaceAnalogueResetHighThreshold_Eighth	1.3.6.1.4.1.818.1.2.8.3.2.1.7	Integer32	read-write	After an alarm, value which has to be crossed by the analogue input, in order to remove the high alarm condition (hysteresis)
ioInterfaceTraps_Eighth	1.3.6.1.4.1.818.1.2.8.4
NTF ioAlarmGenericChange_Eighth	1.3.6.1.4.1.818.1.2.8.4.0.1			An generic change of a digital input/digital output/analog input has become active.
geModem	1.3.6.1.4.1.818.1.3
NUM geModemStatus	1.3.6.1.4.1.818.1.3.1	NonNegativeInteger32	read-only	The status of the modem, controlled by the addressed device. The status word is a collection of bits, as specified below. The SNMP value NOSUCHNAME means 'status not (yet) available'. 1 modemStatOnline. There is a valid online connection. 2 modemStatError. The last operation has failed. The device will clear this bit when a new modem command is received. 4 unused (should be defined = 0). 8 unused (should be defined = 0). 16 modemStatDialling. The dialling procedure is pending. 32 modemStatBusy. The device is performing some operation, and can not be accessed, temporarily. 64 unused (should be defined = 0). 128 modemStatNoModem. The modem is not connected or not responding. 256 modemStatDCD. The DCD line status signal is on. 512 modemStatRing. The RING line status signal is on. 1024 modemStatCTS. The CTS line status signal is on. 2048 modemStatDSR. The DSR line status signal is on. 4096 unused (should be defined = 0). 8192 unused (should be defined = 0). 16384 unused (should be defined = 0). 32768 unused (should be defined = 0).
NUM geModemNumInitString	1.3.6.1.4.1.818.1.3.2	NonNegativeInteger32	read-only	The number of modem init strings utilized by this ups. This entry indicates the number of rows in the init string table.
geModemInitStringTable	1.3.6.1.4.1.818.1.3.3		not-accessible	A list of init string table entries. The number of entries is given by the value of geModemNumInitString.
geModemInitStringEntry	1.3.6.1.4.1.818.1.3.3.1		not-accessible	An entry containing information applicable to a particular Init string.
NUM geModemInitStringLineIndex	1.3.6.1.4.1.818.1.3.3.1.1	PositiveInteger32	not-accessible	The Init string line identifier.
STR geModemInitstring	1.3.6.1.4.1.818.1.3.3.1.2	DisplayString	read-write	A modem Init string.
NUM geModemNumPhoneNumber	1.3.6.1.4.1.818.1.3.4	NonNegativeInteger32	read-only	The number of modem phone numbers utilized by this ups. This entry indicates the number of rows in the table.
geModemPhoneNumberTable	1.3.6.1.4.1.818.1.3.5		not-accessible	A list of phone number table entries. The number of entries is given by the value of geModemNumPhoneNumber.
geModemPhoneNumberEntry	1.3.6.1.4.1.818.1.3.5.1		not-accessible	An entry containing information applicable to a particular phone number.
NUM geModemPhoneNumberLineIndex	1.3.6.1.4.1.818.1.3.5.1.1	PositiveInteger32	not-accessible	The phone number line identifier.
STR geModemPhoneNumber	1.3.6.1.4.1.818.1.3.5.1.2	DisplayString	read-write	A phone number.
geDevices	1.3.6.1.4.1.818.1.100
geDevicesDescriptions	1.3.6.1.4.1.818.1.100.1
advSNMPWebIntCard	1.3.6.1.4.1.818.1.100.1.1
snmpPWebIntCard	1.3.6.1.4.1.818.1.100.1.2
snmpWebIntBox	1.3.6.1.4.1.818.1.100.1.3
snmpSWPFAgent	1.3.6.1.4.1.818.1.100.1.4
snmpSWJUMPAgent	1.3.6.1.4.1.818.1.100.1.5
geSoftware	1.3.6.1.4.1.818.2
geClient	1.3.6.1.4.1.818.2.1
STR geClientProcessor	1.3.6.1.4.1.818.2.1.1	DisplayString	read-only	The processor used by the clients machine.
STR geClientOperatingSystem	1.3.6.1.4.1.818.2.1.2	DisplayString	read-only	Operating system on which the client runs.
STR geClientJavaRuntimeVersion	1.3.6.1.4.1.818.2.1.3	DisplayString	read-only	JavaRuntimeVersion of the client machine.
NUM geClientMaxSizeOfLogfiles	1.3.6.1.4.1.818.2.1.4	NonNegativeInteger32	read-write	The max. size of the logfiles in Kb.
STR geClientLanguageSelection	1.3.6.1.4.1.818.2.1.5	DisplayString	read-only	Shows the currently activated language of the client.
NUM geClientInternalCommunicationPort	1.3.6.1.4.1.818.2.1.6	NonNegativeInteger32	read-write	UDP port used between server and client part.
INT geClientReboot	1.3.6.1.4.1.818.2.1.7	INTEGER	write-only	setting this object causes the protection client to reboot and activate new settings.
NUM geClientNumUPS	1.3.6.1.4.1.818.2.1.8	NonNegativeInteger32	read-only	The number of UPSs utilized by this client. This entry indicates the number of rows in the table.
geClientUPSTable	1.3.6.1.4.1.818.2.1.9		not-accessible	A list of UPS table entries. The number of entries is given by the value of geClientNumUPS.
geClientUPSEntry	1.3.6.1.4.1.818.2.1.9.1		not-accessible	An entry containing information applicable to a particular UPS.
NUM geClientUPSLineIndex	1.3.6.1.4.1.818.2.1.9.1.1	PositiveInteger32	not-accessible	The UPS line identifier.
STR geClientUPSName	1.3.6.1.4.1.818.2.1.9.1.2	DisplayString	read-write	The administrative name of the UPS.
INT geClientUPSCommunicationType	1.3.6.1.4.1.818.2.1.9.1.3	INTEGER	read-write	The method of communication.
STR geClientUPSCommunicationPort	1.3.6.1.4.1.818.2.1.9.1.4	DisplayString	read-write	The communication port.
STR geClientUPSReadCommName	1.3.6.1.4.1.818.2.1.9.1.5	DisplayString	read-write	The Read community string. Used when communication method is SNMP.
STR geClientUPSWriteCommName	1.3.6.1.4.1.818.2.1.9.1.6	DisplayString	read-write	The Write community string. Used when communication method is SNMP.
NUM geClientUPSCommRetries	1.3.6.1.4.1.818.2.1.9.1.7	NonNegativeInteger32	read-write	Number of retries in case an answer times out. When the max. number of retries is reached a lost communication alarm will be raised.
INT geClientAlarmManagement	1.3.6.1.4.1.818.2.1.9.1.8	INTEGER	read-write	Alarm Management enabled or disabled.
NUM geClientPreDelay	1.3.6.1.4.1.818.2.1.9.1.9	NonNegativeInteger32	read-only	The number of second an alarm needs to be active before action is taken.
INT geClientSystemShutdown	1.3.6.1.4.1.818.2.1.9.1.10	INTEGER	read-only	Specifies whether the client should shutdown the machine when an alarm situation occurs.
NUM geClientRuntime	1.3.6.1.4.1.818.2.1.9.1.11	NonNegativeInteger32	read-only	The user defined preferable runtime.
INT geClientUPSShutdown	1.3.6.1.4.1.818.2.1.9.1.12	INTEGER	read-only	Defines whether the UPS will be shut down after an Operating System shutdown.
NUM geClientMaxScriptExecutionTime	1.3.6.1.4.1.818.2.1.9.1.13	NonNegativeInteger32	read-only	The max. number of seconds the script file is allowed to run.
NUM geClientGraceperiod	1.3.6.1.4.1.818.2.1.9.1.14	NonNegativeInteger32	read-only	The time between start of the Operating System shutdown and the UPS shutdown.
NUM geClientNumTests	1.3.6.1.4.1.818.2.1.20	NonNegativeInteger32	read-only	The number of scheduled tests. This entry indicates the number of rows in the table.
geClientTestTable	1.3.6.1.4.1.818.2.1.21		not-accessible	A list of test table entries. The number of entries is given by the value of geClientNumTests.
geClientTestEntry	1.3.6.1.4.1.818.2.1.21.1		not-accessible	An entry containing information applicable to a particular Test.
NUM geClientTestLineIndex	1.3.6.1.4.1.818.2.1.21.1.1	PositiveInteger32	not-accessible	The test line identifier.
I32 geClientTestId	1.3.6.1.4.1.818.2.1.21.1.2	Integer32	read-write	The test Id.
I32 geClientTestDayTime	1.3.6.1.4.1.818.2.1.21.1.3	Integer32	read-write	The time on which the test is due to be performed.
I32 geClientTestWeekDay	1.3.6.1.4.1.818.2.1.21.1.4	Integer32	read-write	The day in the week on which the test will be performed.
I32 geClientTestMonthDay	1.3.6.1.4.1.818.2.1.21.1.5	Integer32	read-write	The month day on which the test will be performed.
NUM geClientNumShutdowns	1.3.6.1.4.1.818.2.1.30	NonNegativeInteger32	read-only	The number of scheduled Shutdowns. This entry indicates the number of rows in the table.
geClientShutdownTable	1.3.6.1.4.1.818.2.1.31		not-accessible	A list of Shutdown table entries. The number of entries is given by the value of geClientNumShutdowns.
geClientShutdownEntry	1.3.6.1.4.1.818.2.1.31.1		not-accessible	An entry containing information applicable to a particular Shutdown.
NUM geClientShutdownLineIndex	1.3.6.1.4.1.818.2.1.31.1.1	PositiveInteger32	not-accessible	The Shutdown line identifier.
I32 geClientShutdownDelay	1.3.6.1.4.1.818.2.1.31.1.2	Integer32	read-write	The delay before start of the Shutdown.
I32 geClientShutdownDuration	1.3.6.1.4.1.818.2.1.31.1.3	Integer32	read-write	The duration of the Shutdown.
I32 geClientShutdownDayTime	1.3.6.1.4.1.818.2.1.31.1.4	Integer32	read-write	The time on which the Shutdown is due to be performed.
I32 geClientShutdownWeekDay	1.3.6.1.4.1.818.2.1.31.1.5	Integer32	read-write	The day in the week on which the Shutdown will be performed.
I32 geClientShutdownMonthDay	1.3.6.1.4.1.818.2.1.31.1.6	Integer32	read-write	The month day on which the Shutdown will be performed.
I32 geClientShutdownPreWarnTime	1.3.6.1.4.1.818.2.1.31.1.7	Integer32	read-write	The number of seconds before start of the shutdown a pre warning will be raised.
geAgent	1.3.6.1.4.1.818.3
geAgentConfig	1.3.6.1.4.1.818.3.1
NUM geAgentUDPPort	1.3.6.1.4.1.818.3.1.1	NonNegativeInteger32	read-write	The UDP port number used by agent.
NUM geAgentWebServerPort	1.3.6.1.4.1.818.3.1.2	NonNegativeInteger32	read-write	The UDP port number used by the HTTP server.
STR geAgentComPort	1.3.6.1.4.1.818.3.1.3	DisplayString	read-write	The COM port used by the agent.
NUM geAgentComTimeout	1.3.6.1.4.1.818.3.1.4	NonNegativeInteger32	read-write	The Timeout delay in seconds of the serial communication.
NUM geAgentComRetries	1.3.6.1.4.1.818.3.1.5	NonNegativeInteger32	read-write	The number of retries when serial communication fails.
STR geAgentReadCommunity	1.3.6.1.4.1.818.3.1.6	DisplayString	read-write	The read community string of the agent.
STR geAgentWriteCommunity	1.3.6.1.4.1.818.3.1.7	DisplayString	read-write	The write community string of the agent.
STR geAgentResponsibleEmailAddress	1.3.6.1.4.1.818.3.1.8	DisplayString	read-write	The email address of the responsible person for this agent.
INT geRFCTrapsToSend	1.3.6.1.4.1.818.3.1.9	INTEGER	read-write	This object defines whether RFC traps need to be send. The bit value 1 indicates that the traps needs to be send, while value 0 does not result in a trap to send.
NUM geIMVTrapsToSend	1.3.6.1.4.1.818.3.1.10	NonNegativeInteger32	read-write	This object defines for which device(s) IMV traps need to be send. The bit value 1 indicates that the trap needs to be send, while value 0 does not result in a trap to send. The value presents the devices as a mask: 1 GenericUPS 2 FirstUPS 4 SecondUPS 8 ThirdUPS 16 FourthUPS 32 FifthUPS 64 SixthUPS 128 SeventhUPS 256 EigthUPS 512 IOInterface
geAgentTraps	1.3.6.1.4.1.818.3.2
NUM geAgentNumTraps	1.3.6.1.4.1.818.3.2.1	NonNegativeInteger32	read-only	The number of configured traps. This entry indicates the number of rows in the table.
geAgentTrapTable	1.3.6.1.4.1.818.3.2.2		not-accessible	A list of trap table entries. The number of entries is given by the value of geAgentNumTraps.
geAgentTrapEntry	1.3.6.1.4.1.818.3.2.2.1		not-accessible	An entry containing information applicable to a particular trap target.
NUM geAgentTrapLineIndex	1.3.6.1.4.1.818.3.2.2.1.1	PositiveInteger32	not-accessible	The Trap line identifier.
STR geAgentTrapAddress	1.3.6.1.4.1.818.3.2.2.1.2	DisplayString	read-write	The destination IP-address of the trap.
STR geAgentTrapCommunity	1.3.6.1.4.1.818.3.2.2.1.3	DisplayString	read-write	The communication string used by the trap.
I32 geAgentTrapPort	1.3.6.1.4.1.818.3.2.2.1.4	Integer32	read-write	The UDP port on the receiving side.

RFC description

UPS system monitoring and control for General Electric parallel uninterruptible power supplies.

Start monitoring GE parallel-redundant UPS installation with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download GE-PARALLELUPS

What Is GE-PARALLELUPS?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description