F3-CFM-MIB

All MIBs › F3-CFM-MIB

Organization: ADVA Optical Networking SE

Last Updated: 2021-01-28

Category: Domain: Telco/Transport, Technology: OAM, Technology: SLA/OAM, Vendor: ADVA Optical

Description: ADVA Optical Networking F3 platform MIB for IEEE 802.1ag Connectivity Fault Management OAM operations on FSP 150 devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is F3-CFM-MIB?

F3-CFM-MIB is an ADVA Optical Networking MIB that extends IEEE 802.1ag / ITU-T Y.1731 Connectivity Fault Management (CFM) for the FSP150CM/CC carrier Ethernet product line. It exposes Maintenance Endpoint (MEP) configuration and state, synthetic loss measurement (SLM) and synthetic loss reply (SLR) parameters, and Alarm Indication Signal (AIS) trigger and interval settings used for OAM-based fault detection across Ethernet service networks. Its core purpose is fault/status monitoring of the Ethernet OAM software layer — the administrative and operational state of each MEP (cfmMepAdminState), whether AIS generation has been triggered and at what client maintenance level, and signal-fail trigger conditions — which reveal service-affecting connectivity faults before they impact traffic more broadly. This module is an ADVA-specific extension of the standard IEEE 802.1ag CFM model and interoperates with the base CFM MIB conventions defined by that standard. It is deployed on FSP150 edge/aggregation nodes providing carrier Ethernet OAM for service assurance. Engineers can download the F3-CFM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in F3-CFM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ADVA FSP150CM/CC carrier Ethernet devices

Monitoring Examples

An operator would poll cfmMepTable/cfmMepEntry for a given MEP's cfmMepAdminState to confirm the maintenance endpoint is enabled, and watch cfmMepAisGenTriggerTypes and cfmSignalFailTriggers to see whether the device has started generating AIS due to an underlying signal-fail condition. Checking cfmMepAisClientMdLevel and cfmMepAisInterval verifies AIS is being sent at the correct maintenance domain level and interval per the service configuration. An unexpected AIS trigger combined with an active signal-fail condition on a MEP would indicate a connectivity fault in the monitored Ethernet path that needs escalation.

What Can Be Monitored

MEP administrative/operational state
AIS trigger status and interval
signal-fail trigger conditions
synthetic loss measurement parameters

Imported Objects

From ADVA-MIB

fsp150cm

OBJECT-IDENTITY

From CM-COMMON-MIB

AdminState
CmPmBinAction
OperationalState
PerfCounter64
SecondaryState
VlanPriority

From CM-ENTITY-MIB

neIndex	OBJECT-TYPE
shelfIndex	OBJECT-TYPE
slotIndex	OBJECT-TYPE

From CM-FACILITY-MIB

cmEthernetAccPortIndex	OBJECT-TYPE
cmEthernetNetPortIndex	OBJECT-TYPE
cmEthernetTrafficPortIndex	OBJECT-TYPE

From IEEE8021-CFM-MIB

Dot1agCfmMDLevel
Dot1agCfmMepId
dot1agCfmMaCompEntry	OBJECT-TYPE
dot1agCfmMaIndex	OBJECT-TYPE
dot1agCfmMaNetEntry	OBJECT-TYPE
dot1agCfmMdIndex	OBJECT-TYPE
dot1agCfmMepEntry	OBJECT-TYPE
dot1agCfmMepIdentifier	OBJECT-TYPE

From IF-MIB

InterfaceIndex

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
StorageType
TEXTUAL-CONVENTION
TruthValue
VariablePointer

OIDs

OID symbolic	OID numeric	Type	Access	Description
ADM cfmAccPortQosShaperAdminState	1.3.6.1.4.1.2544.1.12.13.1.1.3.1.4	AdminState	read-write	This object allows the management of the Shaper Administrative State. Only 'in-service' and 'management' states are allowed.
U32 cfmAccPortQosShaperBufSize	1.3.6.1.4.1.2544.1.12.13.1.1.3.1.3	Unsigned32	read-write	This object identifies the queue buffer size.
U32 cfmAccPortQosShaperCIR	1.3.6.1.4.1.2544.1.12.13.1.1.3.1.2	Unsigned32	read-write	This object identifies the queue CIR.
cfmAccPortQosShaperEntry	1.3.6.1.4.1.2544.1.12.13.1.1.3.1		not-accessible	A list of parameters that set up the CFM QoS Queue profiles. This shaper is created automatically when the first Down MEP is created on a Access Port.
I32 cfmAccPortQosShaperIndex	1.3.6.1.4.1.2544.1.12.13.1.1.3.1.1	Integer32	not-accessible	A unique index associated with the type of Access Port Based Shaper. Index 1 refers to the Shaper associated with PORT-based Down MEPs, Index 2 refers to the Shaper associated with the VID-based Down MEPs.
cfmAccPortQosShaperTable	1.3.6.1.4.1.2544.1.12.13.1.1.3		not-accessible	A list of configurable profile entries for CFM QoS Shapers for Access Port.
ADM cfmDownMEPQosShaperAdminState	1.3.6.1.4.1.2544.1.12.13.1.1.6.1.5	AdminState	read-write	This object allows the management of the Shaper Administrative State. Only 'in-service' and 'management' states are allowed.
U32 cfmDownMEPQosShaperCIR	1.3.6.1.4.1.2544.1.12.13.1.1.6.1.3	Unsigned32	read-write	This object identifies the queue CIR.
cfmDownMEPQosShaperEntry	1.3.6.1.4.1.2544.1.12.13.1.1.6.1		not-accessible	A list of parameters that set up the CFM QoS Queue profiles. This shaper is created automatically when the first Down MEP is created on a Port. Note, this queues is valid for port based Down MEPs, VID based down MEPs on NNI port.
I32 cfmDownMEPQosShaperIndex	1.3.6.1.4.1.2544.1.12.13.1.1.6.1.1	Integer32	not-accessible	A unique index associated with the Shaper for Down MEPs.
NUM cfmDownMEPQosShaperProfile	1.3.6.1.4.1.2544.1.12.13.1.1.6.1.4	VariablePointer	read-write	This object identifies the OID of cmQosQueueProfileIndex in the cmQosQueueProfileTable.
cfmDownMEPQosShaperTable	1.3.6.1.4.1.2544.1.12.13.1.1.6		not-accessible	A list of configurable profile entries for CFM QoS Shapers for down MEPs.
I32 cfmDownMEPQosShaperType	1.3.6.1.4.1.2544.1.12.13.1.1.6.1.2	Integer32	read-only	Type of Shaper for Down MEPs. 1 refers to the Shaper associated with Down MEPs(for both port based and VID based) fot Transimit direction, 2 refers to the Shaper associated with Down MEPs(for both port based and VID based) fot Receiving direction
I32 cfmEthType	1.3.6.1.4.1.2544.1.12.13.1.1.1.1	Integer32	read-only	This object provides the system level Ethernet type for CFM.
cfmExtCompliance	1.3.6.1.4.1.2544.1.12.13.1.2.1.1			Describes the requirements for conformance to the CFM Extensions.
cfmExtGroup	1.3.6.1.4.1.2544.1.12.13.1.2.2.1			****************THIS OBJECT GROUP IS NOW DEPRECATED **************** A collection of objects used to identify CFM extension implementation compliance.
cfmExtScalars	1.3.6.1.4.1.2544.1.12.13.1.1.1
cfmExtSvc	1.3.6.1.4.1.2544.1.12.13.1
cfmExtSvcCompliances	1.3.6.1.4.1.2544.1.12.13.1.2.1
cfmExtSvcConformance	1.3.6.1.4.1.2544.1.12.13.1.2
cfmExtSvcGroups	1.3.6.1.4.1.2544.1.12.13.1.2.2
cfmExtSvcObjects	1.3.6.1.4.1.2544.1.12.13.1.1
cfmGenGroup	1.3.6.1.4.1.2544.1.12.13.1.2.2.2			A collection of objects used to identify CFM extension implementation compliance.
MAC cfmLlbMacAddress	1.3.6.1.4.1.2544.1.12.13.1.1.12.1.1	MacAddress	not-accessible	This object represents the Latching Loopback MAC Addresses.
cfmLlbMacAddressEntry	1.3.6.1.4.1.2544.1.12.13.1.1.12.1		not-accessible	A conceptual row in the cfmMepLlbMacAddressTable.
ROW cfmLlbMacAddressRowStatus	1.3.6.1.4.1.2544.1.12.13.1.1.12.1.2	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cfmLlbMacAddressRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cfmLlbMacAddressRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cfmLlbMacAddressRowStatus object may be modified if the associated instance of this object is equal to active(1).
MAC cfmMacAddress	1.3.6.1.4.1.2544.1.12.13.1.1.1.2	MacAddress	read-only	This object provides the system level Mac address for CFM.
NUM cfmMaCompEntity	1.3.6.1.4.1.2544.1.12.13.1.1.9.1.2	VariablePointer	read-create	This object represents the maComp entity, it is should be port or flow's oid.
cfmMaCompEntry	1.3.6.1.4.1.2544.1.12.13.1.1.9.1		not-accessible	A list of additional maCompEntry.
cfmMaCompGroup	1.3.6.1.4.1.2544.1.12.13.1.2.2.6			A collection of additional objects used to show maComp.
U32 cfmMaCompIndex	1.3.6.1.4.1.2544.1.12.13.1.1.9.1.1	Unsigned32	read-only	This object represents the maComp number value.
cfmMaCompTable	1.3.6.1.4.1.2544.1.12.13.1.1.9		not-accessible	A additional list of MA components.
cfmMaNetEntry	1.3.6.1.4.1.2544.1.12.13.1.1.10.1		not-accessible	A list of additional maNetEntry.
U32 cfmMaNetMepNumbers	1.3.6.1.4.1.2544.1.12.13.1.1.10.1.2	Unsigned32	read-write	This object represents the max number of meps per MA.
T/F cfmMaNetRemoteMepAutoDiscovery	1.3.6.1.4.1.2544.1.12.13.1.1.10.1.1	TruthValue	read-write	This object represents whether learn remote mep automatically.
cfmMaNetTable	1.3.6.1.4.1.2544.1.12.13.1.1.10		not-accessible	A additional list of MA.
ADM cfmMepAdminState	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.1	AdminState	read-write	This object represents the Administrative State of the CFM MEPs.
DOT cfmMepAisClientMdLevel	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.3	Dot1agCfmMDLevel	read-create	AIS Client MD level which is the MD level used to identify any higher level local MEPs for which AIS defect needs to be set or MD level of the ETH-AIS frame generated if there are no local MEPs at this MD level.
T/F cfmMepAisGenEnabled	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.5	TruthValue	read-create	This flag enables/disables propagation of ETH-AIS to client MD levels.
CFM cfmMepAisGenTriggerTypes	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.2	CfmAisGenTriggerTypes	read-create	A bit mask which indicates all the defects that result in triggering an AIS for the higher level MEP or transmission of ETH-AIS.
NUM cfmMepAisInterval	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.4	CfmAisInterval	read-create	ETH-AIS frame transmission interval if decision is made to transmit the ETH-AIS frame.
VLA cfmMepAisPriority	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.6	VlanPriority	read-create	This VLAN priority of the ETH-AIS frame.
NUM cfmMepAssociatedObject	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.23	VariablePointer	read-write	This object represents the associated port, it could be port, flow or flow point.
T/F cfmMepCcmInterfaceStatusTLVControl	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.28	TruthValue	read-write	This attribute controls MEP option of the insertion of the Interface Status TLV in CCM messages.
CFM cfmMepDefects	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.16	CfmMepDefects	read-only	This bit mask indicates defects that not defined in standard 802.1ag MIB such as AIS defect.
VLA cfmMepDmPriority	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.12	VlanPriority	read-create	This attribute specifies the DMM frame VLAN priority.
cfmMepEntry	1.3.6.1.4.1.2544.1.12.13.1.1.2.1		not-accessible	A list of additional MEP parameters such the Y.1731 parameters.
NUM cfmMepErrCCMs	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.14	PerfCounter64	read-only	This provides the total number of errored CCMs on the MEP.
cfmMepExcludedMepListEntry	1.3.6.1.4.1.2544.1.12.13.1.1.7.1		not-accessible	Excluded Remote Mep List for local Mep, not expected to receive OAM from these MEPs.
U32 cfmMepExcludedMepListIdentifier	1.3.6.1.4.1.2544.1.12.13.1.1.7.1.1	Unsigned32	not-accessible	A unique index associated with CfmMepExcludedMepListEntry.
ROW cfmMepExcludedMepListRowStatus	1.3.6.1.4.1.2544.1.12.13.1.1.7.1.2	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cfmMepExcludedMepListRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cfmMepExcludedMepListRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cfmMepExcludedMepListRowStatus object may be modified if the associated instance of this object is equal to active(1).
cfmMepExcludedMepListTable	1.3.6.1.4.1.2544.1.12.13.1.1.7		not-accessible	A list of configurable profile entries for CFM excluded mep list.
cfmMepGroup	1.3.6.1.4.1.2544.1.12.13.1.2.2.3			A collection of objects used to identify additional CFM MEP functions.
I32 cfmMepLbmInterval	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.19	Integer32	read-create	ETH-LBM frame transmission interval.
cfmMepLbrEntry	1.3.6.1.4.1.2544.1.12.13.1.1.8.1		not-accessible	MEP LBR statistic table.
NUM cfmMepLbrInOrder	1.3.6.1.4.1.2544.1.12.13.1.1.8.1.3	PerfCounter64	read-only	Total valid in-order LBR received.
MAC cfmMepLbrMacAddress	1.3.6.1.4.1.2544.1.12.13.1.1.8.1.1	MacAddress	read-only	Source Mac Address of LBR.
I32 cfmMepLbrMepId	1.3.6.1.4.1.2544.1.12.13.1.1.8.1.2	Integer32	read-only	Remote MEP ID.
NUM cfmMepLbrOutOfOder	1.3.6.1.4.1.2544.1.12.13.1.1.8.1.4	PerfCounter64	read-only	Total valid out of order LBR received.
cfmMepLbrTable	1.3.6.1.4.1.2544.1.12.13.1.1.8		not-accessible	A list of configurable profile entries for MepLbr.
cfmMepLlbMacAddressTable	1.3.6.1.4.1.2544.1.12.13.1.1.12		not-accessible	A additional list of MAC Addresses.
T/F cfmMepLlbPortLLEnabled	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.26	TruthValue	read-write	This attribute enables port loopback. In MEF 46 loopback is based on LLFS (Latching Loopback Frame Set) which is untagged or tagged. MEF 46 does not have the notion of port loopback. If this attribute is true a port loopback will be activated instead of loopback for untagged frames when LLFS is untagged.
T/F cfmMepLlbResponderEnabled	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.25	TruthValue	read-write	This attribute specifies whether Latching Loopback Responder function is enabled.
STR cfmMepLlbVidList	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.27	DisplayString	read-write	This is a list of VIDs on which Latching Loopback is allowed. An empty list indicates it is allowed on any VID. This list is shall allow combination of individual VIDs and or ranges. VIDs or VID ranges are comma separated. VID ranges are of the form X1:X2 (range of VIDs from X1 to X2).
CFM cfmMepLLFTriggerTypes	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.15	CfmLLFTriggerTypes	read-create	This bit mask indicates the CFM triggers that result in link loss forwarding.
T/F cfmMepLmCountInProfileEnabled	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.10	TruthValue	read-create	As per the Y.1731 data frames counted for loss measurement shall be in-profile (green) data frames. As an added value, this flag is provided for the device to count all frames instead of green frames only. This flag could be set to false in cases where the remote device is not color aware and/or capable of color marking. Even if the device is capable of color marking and is color aware if the outer tag is not an S-TAG it makes sense to set this flag to false. As defined in IEEE 802.1ad the S-TAG has the drop eligibility bit that is used to mark the frames green or yellow.
T/F cfmMepLmDualEndedCountAllPriosEnabled	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.9	TruthValue	read-create	This attribute is used when Y.1731 probes are created and CCM frames are transmitted with loss measurement counts. As per Y.1731, loss measurement should be done per priority class. The implementation is restricted to support counting of frames for only one priority that can be modified. As an added value there is an option to count all priorities. This flag is used to decide whether to put cumulative data frame counts for all the priorities into the CCM instead of data frame counts for a provisioned individual priority.
T/F cfmMepLmRxCountAllPriosEnabled	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.8	TruthValue	read-create	This attribute is used when Y.1731 probes are created and LMR frames are transmitted. As per Y.1731, loss measurement should be done per priority class. The implementation is restricted to support counting of frames for only one priority that can be modified. As an added value there is an option to count all priorities. This flag is used to decide whether to put cumulative data frame counts for all the priorities into the LMR that is transmitted by the MEP instead of data frame counts for a provisioned individual priority. LMR is sent by a MEP when an LMM is received.
T/F cfmMepLmTxCountAllPriosEnabled	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.7	TruthValue	read-create	This attribute is used when Y.1731 probes are created and LMM frames are transmitted. As per Y.1731, loss measurement should be done per priority class. The implementation is restricted to support counting of frames for only one priority that can be modified. As an added value there is an option to count all priorities. This flag is used to decide whether to put cumulative data frame counts for all the priorities into the LMM that is transmitted by the MEP instead of data frame counts for a provisioned individual priority.
VLA cfmMepLmTxPriority	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.11	VlanPriority	read-create	This attribute is used if cfmMepLmTxCountAllPrios is false. This attribute serves three purposes: - It is the VLAN priority of the LMM. - Data frames transmitted and received with this VLAN priority are counted by the MEP. The transmit count is sent in the LMM and the receive count is used to complete the list of four counts used for the loss measurement. - If an LMR is received with a VLAN priority other than this the LMR is dropped.
OPE cfmMepOperationalState	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.20	OperationalState	read-only	This object represents the Operational State of the CFM MEP.
CFM cfmMepPduVersion	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.24	CfmPduVersionType	read-write	This object indicates the version of the Y.1731 OAM PDUs
NUM cfmMepRxCCMs	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.13	PerfCounter64	read-only	This provides the total number of received CCMs on the MEP.
SEC cfmMepSecondaryState	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.21	SecondaryState	read-only	This object represents the Secondary State of the CFM MEP.
CFM cfmMepSlmEnabled	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.22	CfmSlmEnabledTypes	read-write	This bit mask indicates the whether SLM is enabled per each COS.
CMP cfmMepStatsAction	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.18	CmPmBinAction	read-write	Allows the Manager to clear the CFM level statistics : cfmMepRxCCMs, cfmMepErrCCMs.
cfmMepTable	1.3.6.1.4.1.2544.1.12.13.1.1.2		not-accessible	Additional MEP configuration such as Y.1731 configuration.
U32 cfmMepTagEtherType	1.3.6.1.4.1.2544.1.12.13.1.1.2.1.17	Unsigned32	read-write	This object allows management of Ether Type for MEP VLAN Tag for the MEPs.
ADM cfmNetPortQosShaperAdminState	1.3.6.1.4.1.2544.1.12.13.1.1.4.1.4	AdminState	read-write	This object allows the management of the Shaper Administrative State. Only 'in-service' and 'management' states are allowed.
U32 cfmNetPortQosShaperBufSize	1.3.6.1.4.1.2544.1.12.13.1.1.4.1.3	Unsigned32	read-write	This object identifies the queue buffer size.
U32 cfmNetPortQosShaperCIR	1.3.6.1.4.1.2544.1.12.13.1.1.4.1.2	Unsigned32	read-write	This object identifies the queue CIR.
cfmNetPortQosShaperEntry	1.3.6.1.4.1.2544.1.12.13.1.1.4.1		not-accessible	A list of parameters that set up the CFM QoS Queue profiles. This shaper is created automatically when the first Down MEP is created on a Network Port.
cfmNetPortQosShaperTable	1.3.6.1.4.1.2544.1.12.13.1.1.4		not-accessible	A list of configurable profile entries for CFM QoS Shapers for Network Port.
I32 cfmNetPortQosShaperTypeIndex	1.3.6.1.4.1.2544.1.12.13.1.1.4.1.1	Integer32	not-accessible	A unique index associated with the type of Network Port Based Shaper. Index 1 refers to the Shaper associated with PORT-based Down MEPs, Index 2 refers to the Shaper associated with the VID-based Down MEPs.
cfmPortShaperGroup	1.3.6.1.4.1.2544.1.12.13.1.2.2.4			A collection of objects used to identify CFM Port Shaper functionality.
ADM cfmServerMepAdminState	1.3.6.1.4.1.2544.1.12.13.1.1.5.1.9	AdminState	read-write	This object represents the Administrative State of the Server MEP.
DOT cfmServerMepAisClientMdLevel	1.3.6.1.4.1.2544.1.12.13.1.1.5.1.3	Dot1agCfmMDLevel	read-create	AIS Client MD level which is the MD level used to identify any higher level local MEPs for which AIS defect needs to be set or MD level of the ETH-AIS frame generated if there are no local MEPs at this MD level.
T/F cfmServerMepAisGenEnabled	1.3.6.1.4.1.2544.1.12.13.1.1.5.1.5	TruthValue	read-create	This flag enables/disables propagation of ETH-AIS to client MD levels.
NUM cfmServerMepAisInterval	1.3.6.1.4.1.2544.1.12.13.1.1.5.1.4	CfmAisInterval	read-create	ETH-AIS frame transmission interval if decision is made to transmit the ETH-AIS frame.
VLA cfmServerMepAisPriority	1.3.6.1.4.1.2544.1.12.13.1.1.5.1.6	VlanPriority	read-create	This VLAN priority of the ETH-AIS frame.
NUM cfmServerMepAssociatedPort	1.3.6.1.4.1.2544.1.12.13.1.1.5.1.2	VariablePointer	read-create	This is the port on which the CFM Server MEP is created.
cfmServerMepEntry	1.3.6.1.4.1.2544.1.12.13.1.1.5.1		not-accessible	This allows management of Server MEPs.
cfmServerMepGroup	1.3.6.1.4.1.2544.1.12.13.1.2.2.5			A collection of objects used to identify CFM Server MEP functionality.
I32 cfmServerMepIndex	1.3.6.1.4.1.2544.1.12.13.1.1.5.1.1	Integer32	read-create	The integer index value corresponding to a Server MEP.
OPE cfmServerMepOperationalState	1.3.6.1.4.1.2544.1.12.13.1.1.5.1.10	OperationalState	read-only	This object represents the Operational State of the Server MEP.
ROW cfmServerMepRowStatus	1.3.6.1.4.1.2544.1.12.13.1.1.5.1.8	RowStatus	read-create	The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cfmServerMepRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cfmServerMepRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cfmServerMepRowStatus object may be modified if the associated instance of this object is equal to active(1).
SEC cfmServerMepSecondaryState	1.3.6.1.4.1.2544.1.12.13.1.1.5.1.11	SecondaryState	read-only	This object represents the Secondary State of the CFM MEP.
STO cfmServerMepStorageType	1.3.6.1.4.1.2544.1.12.13.1.1.5.1.7	StorageType	read-create	The type of storage configured for this entry.
cfmServerMepTable	1.3.6.1.4.1.2544.1.12.13.1.1.5		not-accessible	Server MEP management table.
CFM cfmSignalFailTriggers	1.3.6.1.4.1.2544.1.12.13.1.1.1.6	CfmSignalFailTriggers	read-write	This object can be used to configure the list of defects which constitute Signal Fail condition.
ADM cfmTrafficPortQosShaperAdminState	1.3.6.1.4.1.2544.1.12.13.1.1.11.1.4	AdminState	read-write	This object allows the management of the Shaper Administrative State. Only 'in-service' and 'management' states are allowed.
U32 cfmTrafficPortQosShaperBufSize	1.3.6.1.4.1.2544.1.12.13.1.1.11.1.3	Unsigned32	read-write	This object identifies the queue buffer size.
U32 cfmTrafficPortQosShaperCIR	1.3.6.1.4.1.2544.1.12.13.1.1.11.1.2	Unsigned32	read-write	This object identifies the queue CIR.
cfmTrafficPortQosShaperEntry	1.3.6.1.4.1.2544.1.12.13.1.1.11.1		not-accessible	A list of parameters that set up the CFM QoS Queue profiles. This shaper is created automatically when the first Down MEP is created on a Traffic Port.
I32 cfmTrafficPortQosShaperIndex	1.3.6.1.4.1.2544.1.12.13.1.1.11.1.1	Integer32	not-accessible	A unique index associated with the type of Traffic Port Based Shaper. Index 1 refers to the Shaper associated with PORT-based Down MEPs, Index 2 refers to the Shaper associated with the VID-based Down MEPs.
cfmTrafficPortQosShaperTable	1.3.6.1.4.1.2544.1.12.13.1.1.11		not-accessible	A list of configurable entries for CFM QoS Shapers for Traffic Ports.
f3CfmMIB	1.3.6.1.4.1.2544.1.12.13			This module defines the CFM (8021AG) Extension MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA.
MAC slmMulticastMacAddress	1.3.6.1.4.1.2544.1.12.13.1.1.1.3	MacAddress	read-write	This object can be used to configure the Synthetic Loss Measurement(SLM) Multicast MAC Address.
I32 slmOpcode	1.3.6.1.4.1.2544.1.12.13.1.1.1.4	Integer32	read-write	This object can be used to configure the Operation Code for the Synthetic Loss Measurement(SLM) message.
I32 slrOpcode	1.3.6.1.4.1.2544.1.12.13.1.1.1.5	Integer32	read-write	This object can be used to configure the Operation Code for the Synthetic Loss Response(SLR) message.

RFC description

Extends IEEE 802.1ag CFM with ADVA-specific features for connectivity fault management and MEP operations.

Start monitoring ADVA Optical Networking FSP150CM/CC (F3 platform) carrier Ethernet device (802.1ag/Y.1731 Connectivity Fault Management) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download F3-CFM-MIB

What Is F3-CFM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description