HH3C-NQA-MIB

All MIBs › HH3C-NQA-MIB

Organization: Hangzhou H3C Tech. Co., Ltd.

Last Updated: 2006-08-14

Category: Technology: Network Monitoring, Technology: SLA/OAM, Technology: Traffic Monitoring, Vendor: H3C/HH3C

Description: HH3C MIB for Network Quality Analyzer (NQA) test instances measuring network performance metrics such as latency and jitter.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HH3C-NQA-MIB?

HH3C-NQA-MIB is a Hangzhou H3C Tech. proprietary MIB (built on DISMAN-PING-MIB, supplementing RFC 2925) implementing NQA (Network Quality Analyzer) synthetic-test probes. Its control table, keyed by test, records target/source port, TTL, jitter-test admin interval/packet count, HTTP operation type/string, FTP operation type/username/password/string, VPN instance, history retention time/enable, ICPIF advantage factor, and codec type, while a results table records RTT disconnects, timeouts, busies, and no-connections. As a performance/diagnostic MIB it lets an administrator run and review synthetic HTTP/FTP/jitter/voice-quality probes on an H3C device. It is deployed on H3C (Hangzhou) networking equipment (NQA probes). Engineers can download the HH3C-NQA-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HH3C-NQA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C (Hangzhou) networking equipment (NQA probes)

Monitoring Examples

An administrator checks hh3cNqaResultsRttTimeouts to diagnose a failing synthetic-test probe run via NQA on an H3C device.

What Can Be Monitored

synthetic HTTP/FTP/jitter/voice-quality probe results

Imported Objects

From DISMAN-PING-MIB

pingCtlDescr	OBJECT-TYPE
pingCtlEntry	OBJECT-TYPE
pingCtlOwnerIndex	OBJECT-TYPE
pingCtlTargetAddress	OBJECT-TYPE
pingCtlTargetAddressType	OBJECT-TYPE
pingCtlTestName	OBJECT-TYPE
pingCtlType	OBJECT-TYPE

From HH3C-OID-MIB

hh3cRhw

OBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus

How to Use in IPNetwork Monitor

Example using hh3cNqaJitterStatsNumOfRTT OID:

Select an H3C networking equipment (NQA synthetic-test probes) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hh3cNqaJitterStatsNumOfRTT into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of received destination device responses with which jitter test can reach round-trip time. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the jitter climbs well above its normal baseline, since rising jitter often signals network congestion or a degrading path. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hh3cNqa	1.3.6.1.4.1.25506.8.3			The private MIB file includes the test information of the device. It is supplementary for rfc2925.txt.
hh3cNqaObjects	1.3.6.1.4.1.25506.8.3.1
STR hh3cNqaMIBVersion	1.3.6.1.4.1.25506.8.3.1.1	DisplayString	read-only	Version string of this MIB. The format will be: 'Version.Release.Patch: Description' An instance likes: '1.0.0: Initial NQA MIB'
hh3cNqaCtlTable	1.3.6.1.4.1.25506.8.3.1.2		not-accessible	Defines the NQA Control Extend Table for providing, via SNMP, the capability of performing network analysis operations at a remote host.
hh3cNqaCtlEntry	1.3.6.1.4.1.25506.8.3.1.2.1		not-accessible	Defines an entry in the hh3cNqaCtlTable. The operation of this table is same as that of pingResultsTable.
I32 hh3cNqaCtlTargetPort	1.3.6.1.4.1.25506.8.3.1.2.1.1	Integer32	read-create	The destination port that may be used by udpEcho, tcpConnect and jitter probes.
I32 hh3cNqaCtlSourcePort	1.3.6.1.4.1.25506.8.3.1.2.1.2	Integer32	read-create	The source port that may be used by all tests except for dns and dlsw. If no source port is specified, system will create a random port as source port.
I32 hh3cNqaCtlTTL	1.3.6.1.4.1.25506.8.3.1.2.1.3	Integer32	read-create	Specifies the value to store in the TTL Field in the IP packet used to encapsulate the NQA probe.
I32 hh3cNqaCtlJitterAdminInterval	1.3.6.1.4.1.25506.8.3.1.2.1.4	Integer32	read-create	Time value in milliseconds that is an interval between two continuous probes in jitter test. This object is only used by jitter test.
I32 hh3cNqaCtlJitterAdminNumPackets	1.3.6.1.4.1.25506.8.3.1.2.1.5	Integer32	read-create	Packet number that specifys how many packets will be sent in one jitter test. This object is only used by jitter test.
INT hh3cNqaCtlHttpOperationType	1.3.6.1.4.1.25506.8.3.1.2.1.6	INTEGER	read-create	Http operation type: get or post.
STR hh3cNqaCtlHttpOperationString	1.3.6.1.4.1.25506.8.3.1.2.1.7	DisplayString	read-create	Http operation string. For example, if the http operation type is get, the string will be url, home page and http version.
INT hh3cNqaCtlFtpOperationType	1.3.6.1.4.1.25506.8.3.1.2.1.8	INTEGER	read-create	Ftp operation type.
STR hh3cNqaCtlFtpUsername	1.3.6.1.4.1.25506.8.3.1.2.1.9	DisplayString	read-create	Ftp username.
STR hh3cNqaCtlFtpPassword	1.3.6.1.4.1.25506.8.3.1.2.1.10	DisplayString	read-create	Ftp password.
STR hh3cNqaCtlFtpOperationString	1.3.6.1.4.1.25506.8.3.1.2.1.11	DisplayString	read-create	Ftp operation string. If the ftp operation type is get, the string must be the file name which will be gotten from ftp server.
STR hh3cNqaCtlVPNInstance	1.3.6.1.4.1.25506.8.3.1.2.1.12	DisplayString	read-create	VPN name by which system finds route in the specified VPN to send NQA probe packets.
I32 hh3cNqaCtlHistoryKeptTime	1.3.6.1.4.1.25506.8.3.1.2.1.13	Integer32	read-create	To indicate how long the history records will be saved in the pingProbeHistoryTable table after the test stopped.
INT hh3cNqaCtlHistoryEnable	1.3.6.1.4.1.25506.8.3.1.2.1.14	INTEGER	read-create	To indicate whether the history should be recorded in the PingProbeHistoryTable or not. enabled(1) --history will be recorded disabled(2) --history will not be recorded.
I32 hh3cNqaCtlICPIFAdvFactor	1.3.6.1.4.1.25506.8.3.1.2.1.15	Integer32	read-create	The advantage factor depends on the type of access and how the service is to be used. This object will be used while calculating the ICPIF (Calculated Planning Impairment Factor) values. Suggestion values: \|-----------------------------------\|-------\| \| Service \|factor \| \|-----------------------------------\|-------\| \|conventional wire-line \| 0 \| \|-----------------------------------\|-------\| \|mobility within Building \| 5 \| \|-----------------------------------\|-------\| \|mobility within geographical area \| 10 \| \|-----------------------------------\|-------\| \|access to hard-to-reach location \| 20 \| \|-----------------------------------\|-------\|
INT hh3cNqaCtlCodecType	1.3.6.1.4.1.25506.8.3.1.2.1.16	INTEGER	read-create	To indicate the codec type to be used with jitter probe. This is applicable only for the jitter probe.
hh3cNqaResultsTable	1.3.6.1.4.1.25506.8.3.1.3		not-accessible	Defines the NQA Results Extend Table for providing the capability of performing NQA operations at a remote host. The results of these operations are stored in the hh3cNqaResultsTable. The operation of this table is same as that of pingResultsTable.
hh3cNqaResultsEntry	1.3.6.1.4.1.25506.8.3.1.3.1		not-accessible	The operation of this table is same as that of pingResultsTable.
U32 hh3cNqaResultsRttNumDisconnects	1.3.6.1.4.1.25506.8.3.1.3.1.1	Unsigned32	read-only	The number of times that a NQA probe failed because the destination became disconnected. For connectionless protocol pingCtlTypes, this number should be zero.
U32 hh3cNqaResultsRttTimeouts	1.3.6.1.4.1.25506.8.3.1.3.1.2	Unsigned32	read-only	The number of times that a NQA probe failed because the probe timed out.
U32 hh3cNqaResultsRttBusies	1.3.6.1.4.1.25506.8.3.1.3.1.3	Unsigned32	read-only	The number of times that a NQA probe failed because all NQA tasks have been running. If a new probe fails to start, the value of this object is incremented. The next test will not start until the next Frequency.
U32 hh3cNqaResultsRttNoConnections	1.3.6.1.4.1.25506.8.3.1.3.1.4	Unsigned32	read-only	The number of times that a NQA probe failed because the probe destination is unavailable. For connectionless protocol pingCtlTypes, this number should be zero.
U32 hh3cNqaResultsRttDrops	1.3.6.1.4.1.25506.8.3.1.3.1.5	Unsigned32	read-only	The number of times that a NQA operation failed to initiated for unavailibility of necessary internal resources.
U32 hh3cNqaResultsRttSequenceErrors	1.3.6.1.4.1.25506.8.3.1.3.1.6	Unsigned32	read-only	The number of packets arrived out of sequence.
U32 hh3cNqaResultsRttStatsErrors	1.3.6.1.4.1.25506.8.3.1.3.1.7	Unsigned32	read-only	The number of some other errors.
U32 hh3cNqaResultsMaxDelaySD	1.3.6.1.4.1.25506.8.3.1.3.1.8	Unsigned32	read-only	The maximal delay from source device to destination device. Currently this value is only used for jitter test, and this value must be 0 in other type test. In jitter test, if destination system time is not valid, the SD delay may be set 0.
U32 hh3cNqaResultsMaxDelayDS	1.3.6.1.4.1.25506.8.3.1.3.1.9	Unsigned32	read-only	The maximal delay from destination device to source device. Currently this value is only used for jitter test, and this value is 0 in other type test. In jitter test, if destination system time is not valid, the DS delay may be set 0.
U32 hh3cNqaResultsLostPacketRatio	1.3.6.1.4.1.25506.8.3.1.3.1.10	Unsigned32	read-only	The value of this object reflects the drop rate of NQA test. For example, this value is 30 that means source device only had received 70% packets of total sent packets.
U32 hh3cNqaResultsPacketLateArrival	1.3.6.1.4.1.25506.8.3.1.3.1.11	Unsigned32	read-only	The value of this object indicates the number of the packets that arrived after the timeout.
U32 hh3cNqaResultsRttSum	1.3.6.1.4.1.25506.8.3.1.3.1.12	Unsigned32	read-only	The sum of round trip time.
U32 hh3cNqaResultsNumOfDelaySD	1.3.6.1.4.1.25506.8.3.1.3.1.13	Unsigned32	read-only	The number of delay from source to destination that are successfully measured.
U32 hh3cNqaResultsMinDelaySD	1.3.6.1.4.1.25506.8.3.1.3.1.14	Unsigned32	read-only	The minimum of all one way times from source to destination.
U32 hh3cNqaResultsSumDelaySD	1.3.6.1.4.1.25506.8.3.1.3.1.15	Unsigned32	read-only	The sum of one way times from source to destination.
U32 hh3cNqaResultsSum2DelaySD	1.3.6.1.4.1.25506.8.3.1.3.1.16	Unsigned32	read-only	The sum of squares of one way times from source to destination.
U32 hh3cNqaResultsNumOfDelayDS	1.3.6.1.4.1.25506.8.3.1.3.1.17	Unsigned32	read-only	The number of delay from destination to source that are successfully measured.
U32 hh3cNqaResultsMinDelayDS	1.3.6.1.4.1.25506.8.3.1.3.1.18	Unsigned32	read-only	The minimum of all one way times from destination to source.
U32 hh3cNqaResultsSumDelayDS	1.3.6.1.4.1.25506.8.3.1.3.1.19	Unsigned32	read-only	The sum of one way times from destination to source.
U32 hh3cNqaResultsSum2DelayDS	1.3.6.1.4.1.25506.8.3.1.3.1.20	Unsigned32	read-only	The sum of squares of one way times from destination to source.
hh3cNqaJitterStatsTable	1.3.6.1.4.1.25506.8.3.1.4		not-accessible	Statistics table for latest jitter activity.
hh3cNqaJitterStatsEntry	1.3.6.1.4.1.25506.8.3.1.4.1		not-accessible	An entry contains the statistics for the latest jitter activity. This entry is created only if the pingCtlType is hh3cNqajitter.
C32 hh3cNqaJitterStatsNumOfRTTEx	1.3.6.1.4.1.25506.8.3.1.4.1.1	Counter32	read-only	The number of received destination device responses with which jitter test can reach round-trip time.
G32 hh3cNqaJitterStatsMinOfPositivesSD	1.3.6.1.4.1.25506.8.3.1.4.1.2	Gauge32	read-only	The value of time that records the minimal positive jitter value from source to destination in the jitter test.
G32 hh3cNqaJitterStatsMaxOfPositivesSD	1.3.6.1.4.1.25506.8.3.1.4.1.3	Gauge32	read-only	The value of time that records the maximal positive jitter value from source to destination in the jitter test.
G32 hh3cNqaJitterStatsNumOfPositivesSD	1.3.6.1.4.1.25506.8.3.1.4.1.4	Gauge32	read-only	The number that records positive jitter times from source to destination in the jitter test. The total number of the value of all positive jitters in packets sent from source to destination.
G32 hh3cNqaJitterStatsSumOfPositivesSD	1.3.6.1.4.1.25506.8.3.1.4.1.5	Gauge32	read-only	The value of time that records the sum of positive jitter values from source to destination in the jitter test.
G32 hh3cNqaJitterStatsSum2PositivesSD	1.3.6.1.4.1.25506.8.3.1.4.1.6	Gauge32	read-only	The value of time that records the sum of square of positive jitter values from source to destination in the jitter test.
G32 hh3cNqaJitterStatsMinOfNegativesSD	1.3.6.1.4.1.25506.8.3.1.4.1.7	Gauge32	read-only	The value of time that records the minimal absolute values of negative jitter value from source to destination in the jitter test.
G32 hh3cNqaJitterStatsMaxOfNegativesSD	1.3.6.1.4.1.25506.8.3.1.4.1.8	Gauge32	read-only	The value of time that records the maximal absolute values of negative jitter value from source to destination in the jitter test.
G32 hh3cNqaJitterStatsNumOfNegativesSD	1.3.6.1.4.1.25506.8.3.1.4.1.9	Gauge32	read-only	The number that records negative jitter times from source to destination in the jitter test. The total number of all negative jitter values in packets sent from source to destination.
G32 hh3cNqaJitterStatsSumOfNegativesSD	1.3.6.1.4.1.25506.8.3.1.4.1.10	Gauge32	read-only	The value of time that records the sum of negative jitter values from source to destination in the jitter test. The total number of the value of all negative jitters in packets sent from source to destination.
G32 hh3cNqaJitterStatsSum2NegativesSD	1.3.6.1.4.1.25506.8.3.1.4.1.11	Gauge32	read-only	The value of time that records the sum of square of negative jitter values from source to destination in the jitter test.
G32 hh3cNqaJitterStatsMinOfPositivesDS	1.3.6.1.4.1.25506.8.3.1.4.1.12	Gauge32	read-only	The value of time that records the minimal positive jitter value from destination to source in the jitter test.
G32 hh3cNqaJitterStatsMaxOfPositivesDS	1.3.6.1.4.1.25506.8.3.1.4.1.13	Gauge32	read-only	The value of time that records the maximal positive jitter value from destination to source in the jitter test.
G32 hh3cNqaJitterStatsNumOfPositivesDS	1.3.6.1.4.1.25506.8.3.1.4.1.14	Gauge32	read-only	The number that records positive jitter times from destination to source in the jitter test.
G32 hh3cNqaJitterStatsSumOfPositivesDS	1.3.6.1.4.1.25506.8.3.1.4.1.15	Gauge32	read-only	The value of time that records the sum of positive jitter values from destination to source in the jitter test.
G32 hh3cNqaJitterStatsSum2PositivesDS	1.3.6.1.4.1.25506.8.3.1.4.1.16	Gauge32	read-only	The value of time that records the sum of square of positive jitter values from destination to source in the jitter test.
G32 hh3cNqaJitterStatsMinOfNegativesDS	1.3.6.1.4.1.25506.8.3.1.4.1.17	Gauge32	read-only	The value of time that records the minimal absolute values of negative jitter value from destination to source in the jitter test.
G32 hh3cNqaJitterStatsMaxOfNegativesDS	1.3.6.1.4.1.25506.8.3.1.4.1.18	Gauge32	read-only	The value of time that records the maximal absolute values of negative jitter value from destination to source in the jitter test.
G32 hh3cNqaJitterStatsNumOfNegativesDS	1.3.6.1.4.1.25506.8.3.1.4.1.19	Gauge32	read-only	The number that records negative jitter times from destination to source in the jitter test.
G32 hh3cNqaJitterStatsSumOfNegativesDS	1.3.6.1.4.1.25506.8.3.1.4.1.20	Gauge32	read-only	The value of time that records the sum of negative jitter values from destination to source in the jitter test.
G32 hh3cNqaJitterStatsSum2NegativesDS	1.3.6.1.4.1.25506.8.3.1.4.1.21	Gauge32	read-only	The value of time that records the sum of square of negative jitter values from destination to source in the jitter test.
G32 hh3cNqaJitterStatsPacketLossSD	1.3.6.1.4.1.25506.8.3.1.4.1.22	Gauge32	read-only	The lost packets number sent from source to destination.
G32 hh3cNqaJitterStatsPacketLossDS	1.3.6.1.4.1.25506.8.3.1.4.1.23	Gauge32	read-only	The lost packets number sent from destination to source.
G32 hh3cNqaJitterStatsAvePositivesSD	1.3.6.1.4.1.25506.8.3.1.4.1.24	Gauge32	read-only	The value of time that records the average positive jitter value from source to destination.
G32 hh3cNqaJitterStatsAveNegativesSD	1.3.6.1.4.1.25506.8.3.1.4.1.25	Gauge32	read-only	The value of time that records the average negative jitter value from source to destination.
G32 hh3cNqaJitterStatsAvePositivesDS	1.3.6.1.4.1.25506.8.3.1.4.1.26	Gauge32	read-only	The value of time that records the average positive jitter value from destination to source.
G32 hh3cNqaJitterStatsAveNegativesDS	1.3.6.1.4.1.25506.8.3.1.4.1.27	Gauge32	read-only	The value of time that records the average negative jitter value from destination to source.
G32 hh3cNqaJitterStatsPktLossUnknown	1.3.6.1.4.1.25506.8.3.1.4.1.28	Gauge32	read-only	The number of packets which is lost with unknown reason.
G32 hh3cNqaJitterStatsOperOfICPIF	1.3.6.1.4.1.25506.8.3.1.4.1.29	Gauge32	read-only	The ICPIF (Calculated Planning Impairment Factor) value for the latest jitter test.
G32 hh3cNqaJitterStatsOperOfMOS	1.3.6.1.4.1.25506.8.3.1.4.1.30	Gauge32	read-only	The MOS (Mean Opinion Score) value for the latest jitter test.
INT hh3cNqaAgentEnable	1.3.6.1.4.1.25506.8.3.1.5	INTEGER	read-write	Enable NQA agent function.
hh3cNqaTcpServerTable	1.3.6.1.4.1.25506.8.3.1.6		not-accessible	A table which contains the status of NQA tcp server configuration information.
hh3cNqaTcpServerEntry	1.3.6.1.4.1.25506.8.3.1.6.1		not-accessible	A table which contains the status of NQA tcp server configuration information. This entry includes not only the tcp server ip address but also the tcp server port.
IP hh3cNqaTcpServerIpAddress	1.3.6.1.4.1.25506.8.3.1.6.1.1	InetAddress	not-accessible	Tcp server's ip address.
I32 hh3cNqaTcpServerPort	1.3.6.1.4.1.25506.8.3.1.6.1.2	Integer32	not-accessible	Tcp server's port number.
ROW hh3cNqaTcpServerRowStatus	1.3.6.1.4.1.25506.8.3.1.6.1.3	RowStatus	read-create	hh3cNqaTcpServerIpAddress and hh3cNqaTcpServerPort must be set during a creation operation.
hh3cNqaUdpServerTable	1.3.6.1.4.1.25506.8.3.1.7		not-accessible	Status of NQA udp server configuration information.
hh3cNqaUdpServerEntry	1.3.6.1.4.1.25506.8.3.1.7.1		not-accessible	This entry includes not only the udp server ip address but also the udp server udp port.
IP hh3cNqaUdpServerIpAddress	1.3.6.1.4.1.25506.8.3.1.7.1.1	InetAddress	not-accessible	Udp server's ip address.
I32 hh3cNqaUdpServerPort	1.3.6.1.4.1.25506.8.3.1.7.1.2	Integer32	not-accessible	Udp server's port number.
ROW hh3cNqaUdpServerRowStatus	1.3.6.1.4.1.25506.8.3.1.7.1.3	RowStatus	read-create	hh3cNqaUdpServerIpAddress and hh3cNqaUdpServerPort must be set during a creation operation.
INT hh3cNqaServerEnable	1.3.6.1.4.1.25506.8.3.1.8	INTEGER	read-write	Enable NQA server function.
I32 hh3cNqaStatsMaxGroupNumber	1.3.6.1.4.1.25506.8.3.1.9	Integer32	read-only	The maximum number saved per group. The maximum value of hh3cNqaCtlStatisticsGroupNumber can not exceed the value of this object.
hh3cNqaStatisticsCtlTable	1.3.6.1.4.1.25506.8.3.1.10		not-accessible	Defines the NQA statistics control table for providing, via SNMP, the capability of performing NQA operations at a remote host. The results of these operations are stored in the hh3cNqaStatisticsResultsTable and the hh3cNqaGroupStatsJitterTable.
hh3cNqaStatisticsCtlEntry	1.3.6.1.4.1.25506.8.3.1.10.1		not-accessible	Defines an entry in the hh3cNqaStatisticsCtlTable. The hh3cNqaStatisticsCtlTable has the same index as the pingCtlTable in order for a hh3cNqaStatisticsCtlTable to correspond to the pingCtlEntry.
U32 hh3cNqaCtlStatisticsInterval	1.3.6.1.4.1.25506.8.3.1.10.1.1	Unsigned32	read-create	Statistic information will be calculated after the time that is the value of hh3cNqaCtlStatisticsInterval.
U32 hh3cNqaCtlStatisticsGroupNumber	1.3.6.1.4.1.25506.8.3.1.10.1.2	Unsigned32	read-create	The value of this object indicates the number of group saved. The length of this object is from 1 to hh3cNqaStatsMaxGroupNumber.
U32 hh3cNqaCtlStatisticsKeptTime	1.3.6.1.4.1.25506.8.3.1.10.1.3	Unsigned32	read-create	To indicate how long the statistic information will be saved after the test stops.
DAT hh3cNqaCtlBeginTime	1.3.6.1.4.1.25506.8.3.1.10.1.4	DateAndTime	read-create	Time at which the type-specified test will start.
U32 hh3cNqaCtlLifeTime	1.3.6.1.4.1.25506.8.3.1.10.1.5	Unsigned32	read-create	To indicate how long the type-specified test will last.
hh3cNqaStatisticsResultsTable	1.3.6.1.4.1.25506.8.3.1.11		not-accessible	Defines the NQA statistics results table for providing the capability of performing NQA operations at a remote host. The statistics results of these operations in a statistic cycle are stored in the hh3cNqaStatisticsResultsTable. The statistic cycle is the value of hh3cNqaCtlStatisticsInterval. The first two index identify the pingCtlEntry that the probe statistics result (Hh3cNqaStatisticsResultsEntry) belongs to.
hh3cNqaStatisticsResultsEntry	1.3.6.1.4.1.25506.8.3.1.11.1		not-accessible	Defines an entry in the hh3cNqaStatisticsResultsTable. The hh3cNqaStatisticsResultsTable has the same index as the pingCtlTable in order for a hh3cNqaStatisticsResultsEntry to correspond to the pingCtlEntry that caused it to be created.
U32 hh3cNqaStatResIndex	1.3.6.1.4.1.25506.8.3.1.11.1.1	Unsigned32	not-accessible	An entry in this table is created when the statistics result of a NQA probe is determined. An implementation MUST start assigning hh3cNqaStatResIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
IPt hh3cNqaStatResIpTargetAddressType	1.3.6.1.4.1.25506.8.3.1.11.1.2	InetAddressType	read-only	This object indicates the type of address stored in the corresponding hh3cNqaStatResIpTargetAddress object.
IP hh3cNqaStatResIpTargetAddress	1.3.6.1.4.1.25506.8.3.1.11.1.3	InetAddress	read-only	This object represent the host address to be used at a remote host for performing a network analysis operation.
G32 hh3cNqaStatResMinRtt	1.3.6.1.4.1.25506.8.3.1.11.1.4	Gauge32	read-only	The minimum NQA probe round-trip-time (RTT) received. The value of 0 for this object implies that no RTT has been received.
G32 hh3cNqaStatResMaxRtt	1.3.6.1.4.1.25506.8.3.1.11.1.5	Gauge32	read-only	The maximum NQA probe round-trip-time (RTT) received. The value of 0 for this object implies that no RTT has been received.
G32 hh3cNqaStatResAverageRtt	1.3.6.1.4.1.25506.8.3.1.11.1.6	Gauge32	read-only	The average NQA probe round-trip-time (RTT).
C32 hh3cNqaStatResProbeResponses	1.3.6.1.4.1.25506.8.3.1.11.1.7	Counter32	read-only	The number of responses received. The value of this object MUST be reported as 0 when no probe responses have been received.
C32 hh3cNqaStatResSentProbes	1.3.6.1.4.1.25506.8.3.1.11.1.8	Counter32	read-only	The value of this object reflects the number of probes sent. The value of this object MUST be reported as 0 when no probes have been sent.
C32 hh3cNqaStatResRttSumOfSquares	1.3.6.1.4.1.25506.8.3.1.11.1.9	Counter32	read-only	This object contains the sum of the squares for all NQA responses received. The value of this object MUST be reported as 0 when no NQA responses have been received.
DAT hh3cNqaStatResStartTime	1.3.6.1.4.1.25506.8.3.1.11.1.10	DateAndTime	read-only	This object contains the start time of the statistic.
G32 hh3cNqaStatResInterval	1.3.6.1.4.1.25506.8.3.1.11.1.11	Gauge32	read-only	This object contains the interval between two times of statistic.
C32 hh3cNqaStatResRttNumDisconnects	1.3.6.1.4.1.25506.8.3.1.11.1.12	Counter32	read-only	The number of times that a NQA probe failed because the destination became disconnected. For connectionless protocol pingCtlTypes, this number should be zero.
C32 hh3cNqaStatResRttTimeouts	1.3.6.1.4.1.25506.8.3.1.11.1.13	Counter32	read-only	The number of times that a probe failed because the probe timed out.
C32 hh3cNqaStatResRttBusies	1.3.6.1.4.1.25506.8.3.1.11.1.14	Counter32	read-only	The number of times that a NQA probe failed because errors related to sockets.
C32 hh3cNqaStatResRttNoConnections	1.3.6.1.4.1.25506.8.3.1.11.1.15	Counter32	read-only	The number of times that a NQA probe failed because the probe destination is unavailable. For connectionless protocol pingCtlTypes, this number should be zero.
C32 hh3cNqaStatResRttDrops	1.3.6.1.4.1.25506.8.3.1.11.1.16	Counter32	read-only	The number of times that a NQA operation failed to initiate for unavailibility of necessary internal resources.
C32 hh3cNqaStatResRttSequenceErrors	1.3.6.1.4.1.25506.8.3.1.11.1.17	Counter32	read-only	The number of packets arrived out of sequence.
C32 hh3cNqaStatResRttErrors	1.3.6.1.4.1.25506.8.3.1.11.1.18	Counter32	read-only	The number of other errors.
G32 hh3cNqaStatResLostPacketRatio	1.3.6.1.4.1.25506.8.3.1.11.1.19	Gauge32	read-only	The value of this object reflects the drop rate of NQA test packet. For example, if the value is 30, that means source device only had received 70 percent packets of total sent packets.
C32 hh3cNqaStatResPacketLateArrival	1.3.6.1.4.1.25506.8.3.1.11.1.20	Counter32	read-only	The value of this object reflects the number of the packets that arrived after the timeout.
C32 hh3cNqaStatResRttSum	1.3.6.1.4.1.25506.8.3.1.11.1.21	Counter32	read-only	This object contains the sum of the squares for all NQA responses received during the test lifetime. The value of this object MUST be reported as 0 when no NQA responses have been received.
C32 hh3cNqaStatResNumOfDelaySD	1.3.6.1.4.1.25506.8.3.1.11.1.22	Counter32	read-only	The number of one way times from source to destination that are successfully measured.
G32 hh3cNqaStatResMinDelaySD	1.3.6.1.4.1.25506.8.3.1.11.1.23	Gauge32	read-only	The minimum one way times from source to destination.
G32 hh3cNqaStatResMaxDelaySD	1.3.6.1.4.1.25506.8.3.1.11.1.24	Gauge32	read-only	The maximum one way times from source to destination.
C32 hh3cNqaStatResSumDelaySD	1.3.6.1.4.1.25506.8.3.1.11.1.25	Counter32	read-only	The sum of one way times from source to destination.
C32 hh3cNqaStatResSum2DelaySD	1.3.6.1.4.1.25506.8.3.1.11.1.26	Counter32	read-only	The sum of squares of one way times from source to destination.
C32 hh3cNqaStatResNumOfDelayDS	1.3.6.1.4.1.25506.8.3.1.11.1.27	Counter32	read-only	The number of one way times from destination to source that are successfully measured.
G32 hh3cNqaStatResMinDelayDS	1.3.6.1.4.1.25506.8.3.1.11.1.28	Gauge32	read-only	The minimum one way times from destination to source.
G32 hh3cNqaStatResMaxDelayDS	1.3.6.1.4.1.25506.8.3.1.11.1.29	Gauge32	read-only	The maximum one way times from destination to source.
C32 hh3cNqaStatResSumDelayDS	1.3.6.1.4.1.25506.8.3.1.11.1.30	Counter32	read-only	The sum of one way times from destination to source.
C32 hh3cNqaStatResSum2DelayDS	1.3.6.1.4.1.25506.8.3.1.11.1.31	Counter32	read-only	The sum of squares of one way times from destination to source.
hh3cNqaGroupStatsJitterTable	1.3.6.1.4.1.25506.8.3.1.12		not-accessible	Test Group Statistic table for jitter activity in a statistic cycle. The statistic cycle is the value of hh3cNqaCtlStatisticsInterval. The first two index identify the pingCtlEntry that a probe statistics result (Hh3cNqaStatisticsResultsEntry) belongs to.
hh3cNqaGroupStatsJitterEntry	1.3.6.1.4.1.25506.8.3.1.12.1		not-accessible	An entry contains the group statistic information for jitter activity. This entry is created only if the pingCtlType is hh3cNqajitter.
U32 hh3cNqaStatJitterIndex	1.3.6.1.4.1.25506.8.3.1.12.1.1	Unsigned32	not-accessible	An entry in this table is created when the statistic result of a NQA probe in a statistic cycle is determined. An implementation MUST start assigning hh3cNqaStatJitterIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
G32 hh3cNqaStatJitterMinOfPosSD	1.3.6.1.4.1.25506.8.3.1.12.1.2	Gauge32	read-only	The value of time that records the minimal positive jitter value from source to destination in jitter test.
G32 hh3cNqaStatJitterMaxOfPosSD	1.3.6.1.4.1.25506.8.3.1.12.1.3	Gauge32	read-only	The value of time that records the maximal positive jitter value from source to destination in the jitter test.
C32 hh3cNqaStatJitterNumOfPosSD	1.3.6.1.4.1.25506.8.3.1.12.1.4	Counter32	read-only	The number that records positive jitter times from source to destination in the jitter test. The total number of all positive jitter values in packets sent from source to destination.
C32 hh3cNqaStatJitterSumOfPosSD	1.3.6.1.4.1.25506.8.3.1.12.1.5	Counter32	read-only	The value of time that records the sum of positive jitter values from source to destination in the jitter test.
C32 hh3cNqaStatJitterSumOfSquarePosSD	1.3.6.1.4.1.25506.8.3.1.12.1.6	Counter32	read-only	The value of time that records the sum of square of positive jitter values from source to destination in the jitter test.
G32 hh3cNqaStatJitterMinOfNegSD	1.3.6.1.4.1.25506.8.3.1.12.1.7	Gauge32	read-only	The value of time that records the minimal absolute values of negative jitter value from source to destination in the jitter test.
G32 hh3cNqaStatJitterMaxOfNegSD	1.3.6.1.4.1.25506.8.3.1.12.1.8	Gauge32	read-only	The value of time that records the maximal absolute values of negative jitter value from source to destination in the jitter test.
C32 hh3cNqaStatJitterNumOfNegSD	1.3.6.1.4.1.25506.8.3.1.12.1.9	Counter32	read-only	The number that records negative jitter times from source to destination in the jitter test. The total number of all negative jitter values sent from source to destination.
C32 hh3cNqaStatJitterSumOfNegSD	1.3.6.1.4.1.25506.8.3.1.12.1.10	Counter32	read-only	The value of time that records the sum of negative jitter values from source to destination in the jitter test.
C32 hh3cNqaStatJitterSumOfSquareNegSD	1.3.6.1.4.1.25506.8.3.1.12.1.11	Counter32	read-only	The value of time that records the sum of square of negative jitter values from source to destination in the jitter test.
G32 hh3cNqaStatJitterMinOfPosDS	1.3.6.1.4.1.25506.8.3.1.12.1.12	Gauge32	read-only	The value of time that records the minimal positive jitter value from destination to source in the jitter test.
G32 hh3cNqaStatJitterMaxOfPosDS	1.3.6.1.4.1.25506.8.3.1.12.1.13	Gauge32	read-only	The value of time that records the maximal positive jitter value from destination to source in the jitter test.
C32 hh3cNqaStatJitterNumOfPosDS	1.3.6.1.4.1.25506.8.3.1.12.1.14	Counter32	read-only	The number that records positive jitter times from destination to source in the jitter test.
C32 hh3cNqaStatJitterSumOfPosDS	1.3.6.1.4.1.25506.8.3.1.12.1.15	Counter32	read-only	The value of time that records the sum of positive jitter values from destination to source in the jitter test.
C32 hh3cNqaStatJitterSumOfSquarePosDS	1.3.6.1.4.1.25506.8.3.1.12.1.16	Counter32	read-only	The value of time that records the sum of square of positive jitter values destination to source in the jitter test.
G32 hh3cNqaStatJitterMinOfNegDS	1.3.6.1.4.1.25506.8.3.1.12.1.17	Gauge32	read-only	The value of time that records the minimal absolute values of negative jitter value from destination to source in the jitter test.
G32 hh3cNqaStatJitterMaxOfNegDS	1.3.6.1.4.1.25506.8.3.1.12.1.18	Gauge32	read-only	The value of time that records the maximal absolute values of negative jitter value from destination to source in the jitter test.
C32 hh3cNqaStatJitterNumOfNegDS	1.3.6.1.4.1.25506.8.3.1.12.1.19	Counter32	read-only	The number that records negative jitter times from destination to source in the jitter test.
C32 hh3cNqaStatJitterSumOfNegDS	1.3.6.1.4.1.25506.8.3.1.12.1.20	Counter32	read-only	The value of time that records the sum of negative jitter values from destination to source in the jitter test.
C32 hh3cNqaStatJitterSumOfSquareNegDS	1.3.6.1.4.1.25506.8.3.1.12.1.21	Counter32	read-only	The value of time that records the sum of square of negative jitter values from destination to source in the jitter test.
C32 hh3cNqaStatJitterPacketLossSD	1.3.6.1.4.1.25506.8.3.1.12.1.22	Counter32	read-only	The lost packets number sent from source to destination.
C32 hh3cNqaStatJitterPacketLossDS	1.3.6.1.4.1.25506.8.3.1.12.1.23	Counter32	read-only	The lost packets number sent from destination to source.
G32 hh3cNqaStatJitterAvePosSD	1.3.6.1.4.1.25506.8.3.1.12.1.24	Gauge32	read-only	The value of time that records the average positive jitter value from source to destination.
G32 hh3cNqaStatJitterAveNegSD	1.3.6.1.4.1.25506.8.3.1.12.1.25	Gauge32	read-only	The value of time that records the average negative jitter value from source to destination.
G32 hh3cNqaStatJitterAvePosDS	1.3.6.1.4.1.25506.8.3.1.12.1.26	Gauge32	read-only	The value of time that records the average positive jitter value from destination to source.
G32 hh3cNqaStatJitterAveNegDS	1.3.6.1.4.1.25506.8.3.1.12.1.27	Gauge32	read-only	The value of time that records the average negative jitter value from destination to source.
C32 hh3cNqaStatJitterPktLossUnknown	1.3.6.1.4.1.25506.8.3.1.12.1.28	Counter32	read-only	The number of packets which is lost with unknown reason.
G32 hh3cNqaStatJitterMaxOfICPIF	1.3.6.1.4.1.25506.8.3.1.12.1.29	Gauge32	read-only	The maximum of all ICPIF values in a statistic cycle for jitter test.
G32 hh3cNqaStatJitterMinOfICPIF	1.3.6.1.4.1.25506.8.3.1.12.1.30	Gauge32	read-only	The minimum of all ICPIF values in a statistic cycle for jitter test.
G32 hh3cNqaStatJitterMaxOfMOS	1.3.6.1.4.1.25506.8.3.1.12.1.31	Gauge32	read-only	The maximum of all MOS values in a statistic cycle for jitter test.
G32 hh3cNqaStatJitterMinOfMOS	1.3.6.1.4.1.25506.8.3.1.12.1.32	Gauge32	read-only	The minimum of all MOS values in a statistic cycle for jitter test.
hh3cNqaReactionTable	1.3.6.1.4.1.25506.8.3.1.13		not-accessible	A table of NQA test monitoring notification and reaction configuration definitions. An entry is removed from this table when its corresponding pingCtlEntry is deleted.
hh3cNqaReactionEntry	1.3.6.1.4.1.25506.8.3.1.13.1		not-accessible	Defines an entry in the hh3cNqaReactionTable. The first two index elements identify the pingCtlEntry that a hh3cNqaReactItemIndex belongs to. The third index element selects a single reaction.
STR hh3cNqaReactOwnerIndex	1.3.6.1.4.1.25506.8.3.1.13.1.1	SnmpAdminString	accessible-for-notify	The first index of hh3cNqaReactionTable, it is the same as pingCtlOwnerIndex in pingCtlTable. hh3cNqaReactOwnerIndex and hh3cNqaReactTestName identify an existed test.
STR hh3cNqaReactTestName	1.3.6.1.4.1.25506.8.3.1.13.1.2	SnmpAdminString	accessible-for-notify	The second index of hh3cNqaReactionTable, it is the same as pingCtlTestName in pingCtlTable. hh3cNqaReactOwnerIndex and hh3cNqaReactTestName identify an existed test.
U32 hh3cNqaReactItemIndex	1.3.6.1.4.1.25506.8.3.1.13.1.3	Unsigned32	accessible-for-notify	The third index of hh3cNqaReactionTable, it definitely identifies one of the reaction configurations for a test.
INT hh3cNqaReactCheckedElement	1.3.6.1.4.1.25506.8.3.1.13.1.4	INTEGER	read-create	A list of reaction condition type. 'probetime' and 'probefailure' are valid when pingCtlType of the test is not hh3cNqajitter. 'jitterOwdSD': one way time from source to destination in jitter test. 'jitterOwdDS': one way time from destination to source in jitter test. 'jitterrtt', 'jitterpacketloss', 'jittersd', 'jitterds', 'jitterOwdSD' and 'jitterOwdDS' are valid when pingCtlType of the test is hh3cNqajitter. 'icpif' and 'mos' are valid when pingCtlType of the test is hh3cNqajitter and hh3cNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.
U32 hh3cNqaReactThresholdUpperLimit	1.3.6.1.4.1.25506.8.3.1.13.1.5	Unsigned32	read-create	This object defines an administrative upper-threshold value for hh3cNqaReactCheckedElement. The value of this object is zero if hh3cNqaReactCheckedElement is specified as 'jitterpacketloss' and 'probefailure'.
U32 hh3cNqaReactThresholdLowerLimit	1.3.6.1.4.1.25506.8.3.1.13.1.6	Unsigned32	read-create	This object defines an administrative lower-threshold value for hh3cNqaReactCheckedElement. The value of hh3cNqaReactThresholdLowerLimit should be equal or less than the value of hh3cNqaReactThresholdUpperLimit. The value of this object is zero if hh3cNqaReactCheckedElement is specified as 'jitterpacketloss' and 'probefailure'.
INT hh3cNqaReactThresholdType	1.3.6.1.4.1.25506.8.3.1.13.1.7	INTEGER	read-create	This object defines the reaction threshold types. invalid(0): Invalid value. average(1): If reaction threshold type is average and the average value of watched operation exceeds threshold limit, an action specified in hh3cNqaReactActionType is generated when hh3cNqaReactCurrentStatus changes. consecutive(2): If reaction threshold type is consecutive and the times of watched operation consecutively exceeds the limit specified by hh3cNqaReactThresholdConsecNum, an action specified in hh3cNqaReactActionType is generated when hh3cNqaReactCurrentStatus changes. accumulative(3): If reaction threshold type is accumulative and the times of watched operation accumulatively exceeds the limit specified by hh3cNqaReactThresholdAccumNum, an action specified in hh3cNqaReactActionType is generated when hh3cNqaReactCurrentStatus changes. If reaction threshold type is not configured, the value of this object is 'invalid'.
U32 hh3cNqaReactThresholdConsecNum	1.3.6.1.4.1.25506.8.3.1.13.1.8	Unsigned32	read-create	This object defines a consecutive threshold limit. The value is zero when hh3cNqaReactThresholdType is not 'consecutive'.
U32 hh3cNqaReactThresholdAccumNum	1.3.6.1.4.1.25506.8.3.1.13.1.9	Unsigned32	read-create	This object defines an accumulative threshold limit. The value is zero when the hh3cNqaReactThresholdType is not 'accumulative'.
INT hh3cNqaReactActionType	1.3.6.1.4.1.25506.8.3.1.13.1.10	INTEGER	read-create	Specifies the type of reaction to generate if the specified violation type occurs for the monitored element: none - No reaction is generated trapOnly - A trap is generated triggerOnly - All trigger actions defined for this entry are generated trapAndTrigger - Both a trap and all trigger actions are generated
INT hh3cNqaReactCurrentStatus	1.3.6.1.4.1.25506.8.3.1.13.1.11	INTEGER	read-only	Specifies the current status of this reaction entry: invalid - Specifies the reaction entry status is uncertain. overThreshold - Specifies the reaction entry has met the hh3cNqaReactThresholdType and the threshold value. belowThreshold - Specifies the reaction entry has disobeyed the hh3cNqaReactThresholdType and the threshold value.
ROW hh3cNqaReactRowStatus	1.3.6.1.4.1.25506.8.3.1.13.1.12	RowStatus	read-create	This object allows entries to be created and deleted in the hh3cNqaReactionTable. Creation of an entry in this table results in a new set of reaction configurations which take effect immediately. Deletion of an entry in this table results in corresponding reaction configurations are being deleted and stop taking effect.
U32 hh3cNqaReactCheckedNum	1.3.6.1.4.1.25506.8.3.1.13.1.13	Unsigned32	read-only	The number of checked element samples that are monitored.
U32 hh3cNqaReactThresholdNum	1.3.6.1.4.1.25506.8.3.1.13.1.14	Unsigned32	read-only	The number of checked element samples that are over threshold.
hh3cNqaStatisticsReactionTable	1.3.6.1.4.1.25506.8.3.1.14		not-accessible	A table of NQA test monitoring notification and reaction configuration definitions. An entry is removed from this table when its corresponding pingCtlEntry is deleted.
hh3cNqaStatisticsReactionEntry	1.3.6.1.4.1.25506.8.3.1.14.1		not-accessible	Defines an entry in the hh3cNqaStatisticsReactionTable. The first two index elements identify the pingCtlEntry that a hh3cNqaReactItemIndex belongs to. The third index element identifies an entry in the hh3cNqaStatisticsResultsTable. The forth index element selects a single reaction.
STR hh3cNqaStatReactOwnerIndex	1.3.6.1.4.1.25506.8.3.1.14.1.1	SnmpAdminString	not-accessible	The first index of hh3cNqaStatisticsReactionTable, it is the same as pingCtlOwnerIndex in pingCtlTable.
STR hh3cNqaStatReactTestName	1.3.6.1.4.1.25506.8.3.1.14.1.2	SnmpAdminString	not-accessible	The second index of hh3cNqaStatisticsReactionTable, it is the same as pingCtlTestName in pingCtlTable.
U32 hh3cNqaStatReactIndex	1.3.6.1.4.1.25506.8.3.1.14.1.3	Unsigned32	not-accessible	The third index of hh3cNqaStatisticsReactionTable. An entry in this table is created when the statistics result of a NQA probe is determined. An implementation MUST start assigning hh3cNqaStatResIndex values at 1 and wrap after exceeding the maximum possible value as defined by the limit of this object ('ffffffff'h).
U32 hh3cNqaStatReactItemIndex	1.3.6.1.4.1.25506.8.3.1.14.1.4	Unsigned32	not-accessible	The forth index of hh3cNqaStatisticsReactionTable, it definitely identifies one of the reaction configurations for a test
C32 hh3cNqaStatReactCheckedNum	1.3.6.1.4.1.25506.8.3.1.14.1.5	Counter32	read-only	The number of checked element samples that are monitored.
C32 hh3cNqaStatReactThresholdNum	1.3.6.1.4.1.25506.8.3.1.14.1.6	Counter32	read-only	The number of checked element samples that are over threshold.
hh3cNqaImplementationTypeDomains	1.3.6.1.4.1.25506.8.3.2
hh3cNqaUdpEcho	1.3.6.1.4.1.25506.8.3.2.1			Indicates that an implementation is using the UDP based echo server. Notes: The hh3cNqaCtlTargetPort and hh3cNqaCtlSourcePort need to be set, while in the pingUdpEcho Node, hh3cNqaCtlTargetPort must be set to the default value.
hh3cNqaTcpconnect	1.3.6.1.4.1.25506.8.3.2.2			Indicates that an implementation is attempting to connect to a TCP port in order to calculate a round trip time. Notes: The hh3cNqaCtlTargetPort and hh3cNqaCtlSourcePort need to be set, while in the pingTcpConnectionAttempt Node, hh3cNqaCtlTargetPort must be set to the default value.
hh3cNqajitter	1.3.6.1.4.1.25506.8.3.2.3			Indicates that an implementation is using udp for packet transfers. 'jitter' will cause the NQA(Network Quality Analysis) application to perform delay variance analysis.
hh3cNqaHttp	1.3.6.1.4.1.25506.8.3.2.4			Indicates that an implementation is using udp for name resolution, tcp connect and tcp data transfer mechanisms for HTTP data download from a particular HTTP Server. It causes the NQA application to perform a download of the object specified in the URL.
hh3cNqadlsw	1.3.6.1.4.1.25506.8.3.2.5			Indicates that an implementation is using tcp for sending keepalives. 'dlsw' will cause the NQA application to perform a keepalive operation to measure the response time of a DLSw peer.
hh3cNqadhcp	1.3.6.1.4.1.25506.8.3.2.6			Indicates that an implementation is using udp for sending dhcp requests. 'dhcp' will cause the NQA application to perform an IP Address lease request/teardown operation.
hh3cNqaftp	1.3.6.1.4.1.25506.8.3.2.7			Indicates that an implementation is using tcp packet for ftp connect and data transfer.
hh3cNqaNotifications	1.3.6.1.4.1.25506.8.3.3
NTF hh3cNqaProbeTimeOverThreshold	1.3.6.1.4.1.25506.8.3.3.1			It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. Probe time(equals to RTT for some type of tests) is not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit. 2. The probe time is accumulatively not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit for a number of times specified in hh3cNqaReactThresholdAccumNum. 3. The probe time is consecutively in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit for a number of times specified in hh3cNqaReactThresholdConsecNum. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is not hh3cNqajitter.
NTF hh3cNqaJitterRTTOverThreshold	1.3.6.1.4.1.25506.8.3.3.2			It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average NQA round-trip-time (RTT) of jitter packets is not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit. 2. The RTT of jitter packets is accumulatively not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit for a number of times specified in hh3cNqaReactThresholdAccumNum in one test. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hh3cNqajitter.
NTF hh3cNqaProbeFailure	1.3.6.1.4.1.25506.8.3.3.3			It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the probe test accumulatively failed for a number of times specified in hh3cNqaReactThresholdAccumNum in one test while the value of hh3cNqaReactThresholdType is 'accumulative'. 2. When the probe test consecutively failed for a number of times specified in hh3cNqaReactThresholdConsecNum in one test while the value of hh3cNqaReactThresholdType is 'consecutive'. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is not hh3cNqajitter.
NTF hh3cNqaJitterPacketLoss	1.3.6.1.4.1.25506.8.3.3.4			It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the jitter packets accumulatively lost for a number of times specified in hh3cNqaReactThresholdAccumNum in one test while the value of hh3cNqaReactThresholdType is 'accumulative'. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hh3cNqajitter.
NTF hh3cNqaJitterSDOverThreshold	1.3.6.1.4.1.25506.8.3.3.5			The SD means the jitter values from source to destination. It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average of SD in one jitter test is not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit and the hh3cNqaReactThresholdType is specified as 'average' type. 2. The average of SD in one jitter test is accumulatively not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit for a number of times specified in hh3cNqaReactThresholdAccumNum and the hh3cNqaReactThresholdType is specified as 'accumulative' type. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hh3cNqajitter.
NTF hh3cNqaJitterDSOverThreshold	1.3.6.1.4.1.25506.8.3.3.6			The DS means the jitter values from destination to source. It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. The average of DS in one jitter test is not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit and the hh3cNqaReactThresholdType is specified as 'average' type. 2. The average of DS in one jitter test is accumulatively not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit for a number of times specified in hh3cNqaReactThresholdAccumNum and the hh3cNqaReactThresholdType is specified as 'accumulative' type. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger' and pingCtlType of the test is hh3cNqajitter.
NTF hh3cNqaICPIFOverThreshold	1.3.6.1.4.1.25506.8.3.3.7			It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the ICPIF value in one jitter test is not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger', pingCtlType of the test is hh3cNqajitter and hh3cNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.
NTF hh3cNqaMOSOverThreshold	1.3.6.1.4.1.25506.8.3.3.8			It is generated when the value of hh3cNqaReactCurrentStatus changes. The change may occur when the watched condition is over threshold or below threshold. The over threshold situations is specified as below. 1. When the MOS value in one jitter test is not in the range hh3cNqaReactThresholdLowerLimit through hh3cNqaReactThresholdUpperLimit. This notification is valid only when hh3cNqaReactActionType is 'trapOnly' or 'trapAndTrigger', pingCtlType of the test is hh3cNqajitter and hh3cNqaCtlCodecType is 'g711Alaw' or 'g711Ulaw' or 'g729A'.

RFC description

H3C (Huawei 3Com) Network Quality Assessment MIB extending RFC 2925 DISMAN-PING-MIB; provides RTT, jitter, packet loss, and ICPIF measurements.

Start monitoring H3C networking equipment (NQA synthetic-test probes) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HH3C-NQA-MIB