All MIBs › CISCO-ITP-GSP-MIB
Organization: Cisco Systems, Inc.
Last Updated: 2010-03-05
Category: Cisco Devices, SNA and Legacy Protocols
Description: Manages ITP global SS7 signaling point configuration and operational status.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CISCO-ITP-GSP-MIB?
CISCO-ITP-GSP-MIB is a Cisco-specific MIB for managing Signalling Points on Cisco's IP Transfer Point (ITP), a hardware/software solution that transports SS7 (Signalling System No. 7) telecom traffic over IP networks, functioning like an SS7 signaling point. It exposes configuration and operational objects for signaling point profiles, utilization thresholds, and event sequencing used in telecom carrier signaling gateways. In monitoring terms it is used to track the operational and performance status of the SS7 signaling function—utilization sampling (cgspUtilSampleInterval, cgspUtilThreshold) acts as a load/performance indicator akin to CPU or link utilization, while cgspEventSequenceNumber and the notifications sub-tree (ciscoGspMIBNotifs) surface fault conditions. CISCO-ITP-GSP-MIB SNMP monitoring in a carrier NOC typically centers on exactly these utilization and event-sequence objects rather than the profile configuration itself. This module explicitly supersedes CISCO-ITP-SP-MIB and is built against ITU SS7 standards, so it depends on both that Cisco predecessor MIB's concepts and the underlying ITU-T SS7 specifications. It is deployed in telecom carrier networks where Cisco ITP nodes interconnect SS7 signaling networks with IP-based cores.
IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-ITP-GSP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco IP Transfer Point (ITP)
Monitoring Examples
An admin would monitor cgspUtilSampleInterval and cgspUtilThreshold together to see if signaling link utilization has crossed the configured threshold, with cgspUtilAbateDelta defining hysteresis before the alarm clears. The cgspProfileTable/cgspProfileEntry rows (keyed by cgspProfileName) expose per-profile settings like cgspProfileMtp2BundleTimer, letting an operator confirm MTP2 timer configuration matches expected SS7 link behavior. Rising cgspEventSequenceNumber values combined with entries under ciscoGspMIBNotifs would flag signaling point faults needing investigation.
What Can Be Monitored
- signaling point utilization
- utilization threshold breaches
- profile configuration (MTP2 timers)
- event sequence/fault notifications
- CLLI code identification
This MIB depends on
Related MIBs
Imported Objects
From CISCO-ITP-TC-MIB
| CItpTcAclId | |
| CItpTcCLLI | |
| CItpTcDisplayPC | |
| CItpTcInstanceNumber | |
| CItpTcLinkSLC | |
| CItpTcLinkType | |
| CItpTcLinksetId | |
| CItpTcNetworkIndicator | |
| CItpTcNetworkName | |
| CItpTcPointCode | |
| CItpTcPointCodeType | |
| CItpTcQos | |
| CItpTcRouteTableName | |
| CItpTcServiceIndicator |
From CISCO-SMI
| ciscoMgmt | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndexOrZero |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType | |
| InetPortNumber |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TimeStamp | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| CIT cgspCLLICode | 1.3.6.1.4.1.9.9.336.1.1.1 | CItpTcCLLI | read-write | Common-Language Location Identification Codes (CLLI Codes). This object identifies the physical location of this device and can provide additional informaton on the device type. |
| T/F cgspCongestionNotifEnabled | 1.3.6.1.4.1.9.9.336.1.7.3 | TruthValue | read-write | The signalling point congestion notification truth value. 'true' Indicates that ciscoGspCongestionChange and ciscoGspRxCongestionChange notification is to be generated when the state changes. That is, the notification generation is enabled. 'false' Indicates that ciscoGspCongestionChange and ciscoGspRxCongestionChange notification generation is disabled. |
| C32 cgspEventSequenceNumber | 1.3.6.1.4.1.9.9.336.1.1.6 | Counter32 | read-only | Each event or notification is required to provide a sequence number to be used by the NMS to determine when messages from a particular device are missing. This value will included in each SS7 notification issued by this device. |
| cgspInstance | 1.3.6.1.4.1.9.9.336.1.3 | |||
| cgspInstanceTable | 1.3.6.1.4.1.9.9.336.1.3.1 | not-accessible | A table that contains the instances of signalling points. Entries are added to this table via cgspInstRowStatus in accordance with the RowStatus convention. | |
| cgspInstanceTableEntry | 1.3.6.1.4.1.9.9.336.1.3.1.1 | not-accessible | A list of instance attributes. | |
| T/F cgspInstCongestionsLevels | 1.3.6.1.4.1.9.9.336.1.3.1.1.7 | TruthValue | read-create | Allow multiple congestion levels. 'true' multiple congestion levels are allowed. 'false' multiple congestion levels are disabled. |
| STR cgspInstDescription | 1.3.6.1.4.1.9.9.336.1.3.1.1.5 | SnmpAdminString | read-create | A textual description for the Signalling point. |
| STR cgspInstDisplayName | 1.3.6.1.4.1.9.9.336.1.3.1.1.4 | SnmpAdminString | read-create | A short identifier for the Signalling point. This value can be set by system administrator or defaults to the local point code formatted as an ASCII string. |
| T/F cgspInstDistSccpUnseq | 1.3.6.1.4.1.9.9.336.1.3.1.1.9 | TruthValue | read-create | Evenly distribute Class 0 SCCP messages as follows. 'true' Evenly distribute 0 SCCP messages is enabled. 'false' Evenly distribute 0 SCCP messages is disabled. |
| T/F cgspInstFastRestart | 1.3.6.1.4.1.9.9.336.1.3.1.1.8 | TruthValue | read-create | The support for fast restarts as follows. 'true' fast restart is enabled. 'false' fast restart is disabled. |
| CIT cgspInstNetwork | 1.3.6.1.4.1.9.9.336.1.3.1.1.1 | CItpTcNetworkName | not-accessible | The network name is used to indicate the network in which this signalling point is participating. One or more instances of signalling points can exist in the same physical device. This identifier will be used to correlate instances of signalling points by network. When multiple instance support is not enabled the network name will default to the null string. An octet string specified by an administrator that must be in human-readable form. The names must conform to the allowed characters that can be specified via Command Line Interface(CLI). The names cannot contain control character and should not contain leading or trailing white space. |
| CIT cgspInstNetworkIndicator | 1.3.6.1.4.1.9.9.336.1.3.1.1.2 | CItpTcNetworkIndicator | read-create | The Network Indicator for this Signalling point instance. |
| CIT cgspInstNumber | 1.3.6.1.4.1.9.9.336.1.3.1.1.11 | CItpTcInstanceNumber | read-only | A unique Identifier assigned to each instance. |
| CIT cgspInstRouteTableName | 1.3.6.1.4.1.9.9.336.1.3.1.1.12 | CItpTcRouteTableName | read-create | The routing table for Signalling network management messages. |
| ROW cgspInstRowStatus | 1.3.6.1.4.1.9.9.336.1.3.1.1.13 | RowStatus | read-create | The object is used by a management station to create or delete the row entry in cgspInstanceTable following the RowStatus textual convention. |
| U32 cgspInstSccpWrrOpcShift | 1.3.6.1.4.1.9.9.336.1.3.1.1.14 | Unsigned32 | read-create | This object indicates the shift amount for the OPC bits in SCCP class1 WRR(Weighted round robin). The range depends on the variant as follows. The ITU range is 0-2 The ANSI range is 0-8 The CHINA range is 0-2 The JAPAN NTT range is 0-2 The JAPAN TTC range is 0-2 |
| CIT cgspInstSccpWrrOption | 1.3.6.1.4.1.9.9.336.1.3.1.1.15 | CItpTcSccpWrrOption | read-create | This object indicate the options for calculate SCCP class 1 traffic loadshare under WRR |
| C32 cgspInstSIUPUReceived | 1.3.6.1.4.1.9.9.336.1.3.3.1.2 | Counter32 | read-only | The number of UPU MSUs that were received for the associated user part(service indicator) and and signalling point instance Q752/5.7. |
| C32 cgspInstSIUPUTransmitted | 1.3.6.1.4.1.9.9.336.1.3.3.1.3 | Counter32 | read-only | The number of UPU MSUs that were transmitted for the associated user part(service indicator) and and signalling point instance. |
| T/F cgspInstSummaryRoutingException | 1.3.6.1.4.1.9.9.336.1.3.1.1.10 | TruthValue | read-create | This object is used to control the usage of the summary route when both a summary route (or ANSI cluster route) and a full point-code route (within that summary) are configured. The object is used to indicate whether the summary route is to be used when the full point-code destination is inaccessible as follows. 'true' Use summary routing. 'false' Do not use summary routing. |
| T/F cgspInstTFR | 1.3.6.1.4.1.9.9.336.1.3.1.1.6 | TruthValue | read-create | Allow transfer restricted messages. 'true' TFR are allowed. 'false' TFR are disabled. |
| CGS cgspInstTimerNumber | 1.3.6.1.4.1.9.9.336.1.3.2.1.1 | CgspTimerNumbers | not-accessible | Index into table containing timer information. |
| ROW cgspInstTimerRowStatus | 1.3.6.1.4.1.9.9.336.1.3.2.1.3 | RowStatus | read-create | The object is used by a management station to create or delete the row entry in cgspInstTimerTable following the RowStatus textual convention. |
| cgspInstTimerTable | 1.3.6.1.4.1.9.9.336.1.3.2 | not-accessible | A table that contains the timer used to configure an instances of signalling points. Entries are added to this table via cgspInstTimerRowStatus in accordance with the RowStatus convention. | |
| cgspInstTimerTableEntry | 1.3.6.1.4.1.9.9.336.1.3.2.1 | not-accessible | This table is used to configure all MTP3 timer values that apply to linksets and links. The values apply to all linkset and links defined to this signalling point(instances). | |
| CGS cgspInstTimerValue | 1.3.6.1.4.1.9.9.336.1.3.2.1.2 | CgspTimerValue | read-create | Value of timer selected by cgspInstTimerNumber object. |
| cgspInstUPUTable | 1.3.6.1.4.1.9.9.336.1.3.3 | not-accessible | The Instance UPU table contains information about the number of UPU MSUs transmitted and received for the specific user part(represented by service indicator) and signalling point instance. The user part is primarily represented with the possible service indicator. This table provides the granularity of information required by Q752 table 5.6 and 5.7. | |
| cgspInstUPUTableEntry | 1.3.6.1.4.1.9.9.336.1.3.3.1 | not-accessible | Each table entry represent the UPU MSU statistics for a specific user part and signalling point instance. | |
| CGS cgspInstUserPartDisplay | 1.3.6.1.4.1.9.9.336.1.3.3.1.4 | CgspDisplayInstanceUserPart | read-only | The associated instance name and user part information formatted for display. |
| CGS cgspInstVariant | 1.3.6.1.4.1.9.9.336.1.3.1.1.3 | CgspSS7Variant | read-create | The SS7 variant used to format data used by this instance. |
| U32 cgspIntervalUPUs | 1.3.6.1.4.1.9.9.336.1.8.2 | Unsigned32 | accessible-for-notify | Number of UPU MSUs received or transmitted during this specific cgspUPUIntervalDuration interval. |
| T/F cgspIsolationNotifEnabled | 1.3.6.1.4.1.9.9.336.1.7.5 | TruthValue | read-write | The isolation notification truth value. 'true' Indicates that the notification of isolation has been enabled. That is, the notification generation is enabled. 'false' Indicates that the notification of isolation has been disabled. |
| cgspLink | 1.3.6.1.4.1.9.9.336.1.6 | |||
| U32 cgspLinkCongestionAbate1 | 1.3.6.1.4.1.9.9.336.1.6.1.1.12 | Unsigned32 | read-create | Threshold used to abate congestion level 1. |
| U32 cgspLinkCongestionAbate2 | 1.3.6.1.4.1.9.9.336.1.6.1.1.13 | Unsigned32 | read-create | Threshold used to abate congestion level 2. |
| U32 cgspLinkCongestionAbate3 | 1.3.6.1.4.1.9.9.336.1.6.1.1.14 | Unsigned32 | read-create | Threshold used to abate congestion level 3. |
| U32 cgspLinkCongestionOnset1 | 1.3.6.1.4.1.9.9.336.1.6.1.1.15 | Unsigned32 | read-create | Threshold used to mark onset of congestion level 1. |
| U32 cgspLinkCongestionOnset2 | 1.3.6.1.4.1.9.9.336.1.6.1.1.16 | Unsigned32 | read-create | Threshold used to mark onset of congestion level 2. |
| U32 cgspLinkCongestionOnset3 | 1.3.6.1.4.1.9.9.336.1.6.1.1.17 | Unsigned32 | read-create | Threshold used to mark onset of congestion level 3. |
| U32 cgspLinkCongestionState | 1.3.6.1.4.1.9.9.336.1.6.1.1.11 | Unsigned32 | read-only | The Signalling link congestion status of this link. 0 is the least congestion level, 3 is the highest congestion level. |
| STR cgspLinkDescription | 1.3.6.1.4.1.9.9.336.1.6.1.1.2 | SnmpAdminString | read-create | A textual description for this link. |
| STR cgspLinkDisplayName | 1.3.6.1.4.1.9.9.336.1.6.1.1.54 | SnmpAdminString | read-create | A short identifier for each link linkset. This value can be set by system administrator or defaults to the linkset name and SLC formatted as an ASCII string. |
| C32 cgspLinkDroppedPkts | 1.3.6.1.4.1.9.9.336.1.6.1.1.55 | Counter32 | read-only | The number of packets that were dropped by this link. |
| NUM cgspLinkifIndex | 1.3.6.1.4.1.9.9.336.1.6.1.1.6 | InterfaceIndexOrZero | read-create | If the link type specified by cgspLinkType is serial or high speed Link, this is the ifIndex specified in IF-MIB, otherwise no significance is to be placed on this value. |
| C32 cgspLinkL2BytesRcvd | 1.3.6.1.4.1.9.9.336.1.6.1.1.82 | Counter32 | read-only | A count of the bytes received on the link including the additional bytes required by underlying protocols. This provides a transport independent mechanism for collection information on link utilization. |
| C32 cgspLinkL2BytesSent | 1.3.6.1.4.1.9.9.336.1.6.1.1.87 | Counter32 | read-only | A count of the bytes sent on the link including the additional bytes required by underlying protocols. This provides a transport independent mechanism for collection information on link utilization. |
| INE cgspLinkLocalPeerPort | 1.3.6.1.4.1.9.9.336.1.6.1.1.51 | InetPortNumber | read-create | When cgspLinkType is set to 'sctpIp' then this object contains the local port number used to create the association supporting this link. This object can be used to obtain information from the cgsp2LocalPeerTable and cgsp2LpIpAddrTable Tables in the CISCO-ITP-GSP2-MIB.my MIB. |
| INT cgspLinkLsacState | 1.3.6.1.4.1.9.9.336.1.6.1.1.59 | INTEGER | read-only | Signalling link activity control state: 'undefined' - link is an undefined state 'inactive' - A Signalling link that is not in operation. 'active' - A Signalling link that is in operation. 'activatingRestoring' - A Signalling that is not operational and is being activated or restored. 'failed' - A Signalling link which is available (not blocked) is marked by level 3 as failed when a changeover order is received. 'actT17wait' - Link activation has failed. Link is placed into this state to wait for timer T17 to expire in order to avoid the oscillation of initial alignment failure and link restart. 'actAnsiWaitDeloaded - Waiting for change back acknowledgement (second attempt). 'actItuWaitStmReady' Wait for Signalling Traffic Management ready event. |
| C32 cgspLinkMtp2T01Counts | 1.3.6.1.4.1.9.9.336.1.6.1.1.67 | Counter32 | read-only | The number of times the alignment ready timer has expired on this link. |
| C32 cgspLinkMtp2T02Counts | 1.3.6.1.4.1.9.9.336.1.6.1.1.68 | Counter32 | read-only | The number of times the not alignment ready timer has expired on this link. |
| C32 cgspLinkMtp2T03Counts | 1.3.6.1.4.1.9.9.336.1.6.1.1.69 | Counter32 | read-only | The number of times the aligned timer has expired on this link. |
| C32 cgspLinkMtp2T04Counts | 1.3.6.1.4.1.9.9.336.1.6.1.1.70 | Counter32 | read-only | The number of times the proving period timer has expired on this link. |
| C32 cgspLinkMtp2T05Counts | 1.3.6.1.4.1.9.9.336.1.6.1.1.71 | Counter32 | read-only | The number of times the sending status indicator busy timer has expired on this link. |
| C32 cgspLinkMtp2T06Counts | 1.3.6.1.4.1.9.9.336.1.6.1.1.72 | Counter32 | read-only | The number of times the remote congestion timer has expired on this link(Q752/1.6). |
| C32 cgspLinkMtp2T07Counts | 1.3.6.1.4.1.9.9.336.1.6.1.1.73 | Counter32 | read-only | The number of times the excessive delay of acknowledgement timer has expired on this link(Q752/1.4). |
| C32 cgspLinkOMAERMCounts | 1.3.6.1.4.1.9.9.336.1.6.1.1.74 | Counter32 | read-only | The number of times the Alignment Error Rate Monitor procedure was started on this link. |
| C32 cgspLinkOMAERMFailCounts | 1.3.6.1.4.1.9.9.336.1.6.1.1.75 | Counter32 | read-only | The number of times the Alignment Error Rate Monitor procedure failed on this link. |
| C32 cgspLinkOMSURMCounts | 1.3.6.1.4.1.9.9.336.1.6.1.1.76 | Counter32 | read-only | The number of times the Signal Unit Error Rate Monitor procedure was started on this link. |
| C32 cgspLinkOMSURMFailCounts | 1.3.6.1.4.1.9.9.336.1.6.1.1.77 | Counter32 | read-only | The number of times the Signal Unit Error Rate Monitor procedure failed on this link. |
| CGS cgspLinkPlanCapacityRcvd | 1.3.6.1.4.1.9.9.336.1.6.1.1.78 | CgspLinkCapacity | read-create | An estimate of the number of bits per second that is expected to be received from this link. This object will be used in combination with cgspUtilSampleInterval, cgspUtilThreshold, cgspUtilThreshold and cgspLinkUtilThresholdRcvd to generate the ciscoGspLinkRcvdUtilChange notification. |
| CGS cgspLinkPlanCapacitySent | 1.3.6.1.4.1.9.9.336.1.6.1.1.83 | CgspLinkCapacity | read-create | An estimate of the number of bits per second that is expected to be sent on this link. This object will be used in combination with cgspUtilSampleInterval, cgspUtilThreshold and cgspLinkUtilThresholdRcvd to generate the ciscoGspLinkSentUtilChange notification. |
| BIT cgspLinkProtocolDetails | 1.3.6.1.4.1.9.9.336.1.6.1.1.58 | Bits | read-only | This object provide details on the protocol states for this link as follows. Changeback control(TCBC) 'tcbcBuffering': Changeback control is buffering data on this link. Changeover control(TCOC) 'tcocBuffering': Changeover control is buffering data on this link Link availability control(TLAC) 'tlacAdjacentSpRestarting': Adjacent Signalling point is restarting. 'tlacEmergencyCoInProgress': Emergency changeover is in progress on this link. 'tlacChangebackInProgress': Changeback is in progress on this link. 'tlacChangeoverInProgress': Changeover is in progress on this link. 'tlacChangeoverFailed': The last changeover operation failed on this link. 'tlacInhibitRetry': Inhibit command will be retried. 'tlacManagementRequest': Management request in progress for this link. 'tlacSpRestarting': Signalling point is in the process of a restart. 'tlacLocalInhibit': Link has been inhibited by a local management operation. 'tlacRemoteInhibit': Link has been inhibited by a remote management operation. 'tlacLocalBlocked': Link is blocked because of a local processor outage. 'tlacRemoteBlocked': Link is blocked because of a remote processor outage. Signalling routing control(TSRC) 'tsrcChangeOverComplete': Changeove request is complete. 'tsrcAdjacentSpRestart': Adjacent Signalling Point is restarting. |
| C32 cgspLinkQ752T1E1 | 1.3.6.1.4.1.9.9.336.1.6.1.1.19 | Counter32 | read-only | Duration of link in the In-Service state Q752/1.1. |
| C32 cgspLinkQ752T1E10 | 1.3.6.1.4.1.9.9.336.1.6.1.1.26 | Counter32 | read-only | Count of 'local automatic changeover' events Q752/1.10. |
| C32 cgspLinkQ752T1E11 | 1.3.6.1.4.1.9.9.336.1.6.1.1.27 | Counter32 | read-only | Count of 'local automatic changeback' events Q752/1.11. |
| C32 cgspLinkQ752T1E12 | 1.3.6.1.4.1.9.9.336.1.6.1.1.91 | Counter32 | read-only | Count of 'Signalling Link Restoration' events Q752/1.12. |
| C32 cgspLinkQ752T1E12Errors | 1.3.6.1.4.1.9.9.336.1.6.1.1.92 | Counter32 | read-only | Count of 'Signalling Link Restoration' error events related to Q752/1.12. i.e., the number of times the link restoration was attempted and the link was not recovered. |
| C32 cgspLinkQ752T1E2 | 1.3.6.1.4.1.9.9.336.1.6.1.1.20 | Counter32 | read-only | Count of Signalling Link failures - All reasons Q752/1.2. |
| C32 cgspLinkQ752T1E3 | 1.3.6.1.4.1.9.9.336.1.6.1.1.21 | Counter32 | read-only | Count of Signalling Link failures - Abnormal FIBR/BSNR Q752/1.3 |
| C32 cgspLinkQ752T1E5 | 1.3.6.1.4.1.9.9.336.1.6.1.1.22 | Counter32 | read-only | Count of Signalling Link failures - Excessive error rate Q752/1.5. |
| C32 cgspLinkQ752T1E7 | 1.3.6.1.4.1.9.9.336.1.6.1.1.23 | Counter32 | read-only | Count of alignment or proving errors Q752/1.7. |
| C32 cgspLinkQ752T1E8 | 1.3.6.1.4.1.9.9.336.1.6.1.1.24 | Counter32 | read-only | Count of signal units received in error Q752/1.8. |
| C32 cgspLinkQ752T1E9 | 1.3.6.1.4.1.9.9.336.1.6.1.1.25 | Counter32 | read-only | Count of negative acknowledgements received Q752/1.9. |
| C32 cgspLinkQ752T2E1 | 1.3.6.1.4.1.9.9.336.1.6.1.1.28 | Counter32 | read-only | Duration of Signalling Link unavailable(for any reason) Q752/2.1. |
| C32 cgspLinkQ752T2E10 | 1.3.6.1.4.1.9.9.336.1.6.1.1.33 | Counter32 | read-only | Count of 'remote processor outage' events Q752/2.10 and Q752/2.11. The standard only requires that events are issued. The entries have been combined into a single entry to track all occurrences of these event types. |
| C32 cgspLinkQ752T2E11 | 1.3.6.1.4.1.9.9.336.1.6.1.1.93 | Counter32 | read-only | Count of 'remote processor recovery' events Q752/2.11. The standard only requires that events are issued. |
| C32 cgspLinkQ752T2E15 | 1.3.6.1.4.1.9.9.336.1.6.1.1.34 | Counter32 | read-only | Count of Status Indicator Busy received Q752/2.15. |
| C32 cgspLinkQ752T2E16 | 1.3.6.1.4.1.9.9.336.1.6.1.1.35 | Counter32 | read-only | Count of local inhibition Q752/2.16 and Q752/2.17. The standard only requires that events are issued. The entries have been combined into a single entry to track all occurrences of these event types. |
| C32 cgspLinkQ752T2E17 | 1.3.6.1.4.1.9.9.336.1.6.1.1.94 | Counter32 | read-only | Count of local uninhibition Q752/2.17. The standard only requires that events are issued. |
| C32 cgspLinkQ752T2E18 | 1.3.6.1.4.1.9.9.336.1.6.1.1.36 | Counter32 | read-only | Count of remote inhibition Q752/2.18 and Q752/2.19. The standard only requires that events are issued. The entries have been combined into a single entry to track all occurrences of these event types. |
| C32 cgspLinkQ752T2E19 | 1.3.6.1.4.1.9.9.336.1.6.1.1.95 | Counter32 | read-only | Count of remote uninhibition Q752/2.19. The standard only requires that events are issued. |
| C32 cgspLinkQ752T2E5 | 1.3.6.1.4.1.9.9.336.1.6.1.1.29 | Counter32 | read-only | Duration of Signalling Link unavailable due to local management actions Q752/2.5. |
| C32 cgspLinkQ752T2E6 | 1.3.6.1.4.1.9.9.336.1.6.1.1.30 | Counter32 | read-only | Duration of Signalling Link unavailable due to remote management actions Q752/2.6. |
| C32 cgspLinkQ752T2E7 | 1.3.6.1.4.1.9.9.336.1.6.1.1.31 | Counter32 | read-only | Duration of Signalling Link unavailable due to link failure Q752/2.7. |
| C32 cgspLinkQ752T2E9 | 1.3.6.1.4.1.9.9.336.1.6.1.1.32 | Counter32 | read-only | Duration of Signalling Link unavailable due to remote processor outage Q752/2.9. |
| C32 cgspLinkQ752T3E1 | 1.3.6.1.4.1.9.9.336.1.6.1.1.37 | Counter32 | read-only | The number of MTP3 bytes sent by this link. This measurement is specified in Q752/3.1 |
| C32 cgspLinkQ752T3E10L1 | 1.3.6.1.4.1.9.9.336.1.6.1.1.45 | Counter32 | read-only | The number of packets(MSUs) discarded due to Signalling link level 1 congestion Q752/3.10 |
| C32 cgspLinkQ752T3E10L2 | 1.3.6.1.4.1.9.9.336.1.6.1.1.46 | Counter32 | read-only | The number of packets(MSUs) discard due to Signalling link level 2 congestion Q752/3.10 |
| C32 cgspLinkQ752T3E10L3 | 1.3.6.1.4.1.9.9.336.1.6.1.1.47 | Counter32 | read-only | The number of packets(MSUs) discard due to Signalling link level 3 congestion Q752/3.10 |
| C32 cgspLinkQ752T3E11L1 | 1.3.6.1.4.1.9.9.336.1.6.1.1.48 | Counter32 | read-only | The number times this Signalling link entered congestion level 1 and packets were discarded. This measurement is specified in Q752/3.11 |
| C32 cgspLinkQ752T3E11L2 | 1.3.6.1.4.1.9.9.336.1.6.1.1.49 | Counter32 | read-only | The number times this Signalling link entered congestion level 2 and packets were discarded. This measurement is specified in Q752/3.11 |
| C32 cgspLinkQ752T3E11L3 | 1.3.6.1.4.1.9.9.336.1.6.1.1.50 | Counter32 | read-only | The number times this Signalling link entered congestion level 3 and packets were discarded. This measurement is specified in Q752/3.11 |
| C32 cgspLinkQ752T3E2Bytes | 1.3.6.1.4.1.9.9.336.1.6.1.1.38 | Counter32 | read-only | The number of MTP3 bytes retransmitted on this link. This measurement is specified in Q752/3.2 |
| C32 cgspLinkQ752T3E2Packets | 1.3.6.1.4.1.9.9.336.1.6.1.1.39 | Counter32 | read-only | The number of MTP3 packets retransmitted on this link. This measurement is specified in Q752/3.2 |
| C32 cgspLinkQ752T3E3 | 1.3.6.1.4.1.9.9.336.1.6.1.1.40 | Counter32 | read-only | The number of MTP3 packets sent by this link. This measurement is specified in Q752/3.3. |
| C32 cgspLinkQ752T3E4 | 1.3.6.1.4.1.9.9.336.1.6.1.1.41 | Counter32 | read-only | The number of MTP3 bytes received by this link. This measurement is specified in Q752/3.4 |
| C32 cgspLinkQ752T3E5 | 1.3.6.1.4.1.9.9.336.1.6.1.1.42 | Counter32 | read-only | The number of MTP3 packets received by this link. This measurement is specified in Q752/3.5 |
| C32 cgspLinkQ752T3E6 | 1.3.6.1.4.1.9.9.336.1.6.1.1.43 | Counter32 | read-only | The number times this Signalling link was marked congested. This measurement is specified in Q752/3.6 |
| C32 cgspLinkQ752T3E7 | 1.3.6.1.4.1.9.9.336.1.6.1.1.44 | Counter32 | read-only | Cumulative duration of Signalling link congestion Q752/3.7. |
| CIT cgspLinkQosClass | 1.3.6.1.4.1.9.9.336.1.6.1.1.53 | CItpTcQos | read-create | When cgspLinkType is set to 'sctpIp' then this object contains the quality of service class to be assigned to packets sent on this association. When cgspLinkType is not set to 'sctpIp' then no significance is to be placed on this value. |
| INT cgspLinkReason | 1.3.6.1.4.1.9.9.336.1.6.1.1.4 | INTEGER | read-only | This object provides additional information on the source of a link failure. This object will contain the last reason that caused the link to fail. 'unknown' : Link has failed do to an undetermined cause. 'changeOverInProgress' : Change over in progress. 'mgmtDisconnectRequest' : Management disconnect request. 'linkAlignmentLost' : Link alignment lost. 'connectionLost' : Link connection lost. 'localDisconnect' : Local Disconnect. 'remoteDisconnect' : Remote Disconnect. 'suermFailure' : Signal unit error rate monitor failure. 't1Timeout' : T1 timeout no FISU received. 't2Timeout' : T2 timeout no SIO received. 't3Timeout' : T3 timeout no SIN received. 't6Timeout' : T6 timeout excessive congestion. 't7Timeout' : T7 timeout excessive acknowledgement delay. 'provingFailure' : Link proving failure. 'protocolError-BSN' : Abnormal BSN received. 'protocolError-FIB' : Abnormal FIB received. 'protocolError-SIN' : Abnormal SIB received. 'protocolError-LSSU' : Abnormal LSSU received. 'peerNotReady' : Peer not ready. 'communicationLost' : Communication lost. 'noListenPosted' : No Listen posted. 'bufferNotAvailable' : Unable to allocate buffer. 'cardRemoved' : Link card removed. 'cardInserted' : Link card Inserted. 'falseLinkCongestion' : false link congestion. 'configDownload' : Configuration downloading. 'localInhibit' : Local request to inhibit link. 'localUninhibit' : Local request to uninhibit link. 'remoteInhibit' : Remote request to inhibit link. 'remoteUninhibit': Local request to uninhibit link. 'localBlocked' : Local Processor outage. 'localUnBlocked' : Local Processor recovery. 'remoteBlocked' : Remote Processor outage. 'remoteUnblocked': Remote Processor recovery. 'linkRestored' : Link restored. 'linkTestFailure': Signalling Link Test failure.' |
| C32 cgspLinkReceivedLSSUs | 1.3.6.1.4.1.9.9.336.1.6.1.1.57 | Counter32 | read-only | The number of Link Status Signal Units received on this link. |
| C32 cgspLinkReceivedSIBs | 1.3.6.1.4.1.9.9.336.1.6.1.1.65 | Counter32 | read-only | The number of status indicator 'busy' link status signal units received on this link. The SIB indicates that level two is congested at the transmitting Signalling point. |
| IP cgspLinkRemoteIpAddress | 1.3.6.1.4.1.9.9.336.1.6.3.1.3 | InetAddress | read-create | This object contains the remote IP address used to create the association with the partner of this association. |
| U32 cgspLinkRemoteIpAddrNumber | 1.3.6.1.4.1.9.9.336.1.6.3.1.1 | Unsigned32 | not-accessible | This object specifies the index for the IP addresses in the remote IP Address table |
| ROW cgspLinkRemoteIpAddrRowStatus | 1.3.6.1.4.1.9.9.336.1.6.3.1.4 | RowStatus | read-create | The object is used by a management station to create or delete the row entry in cgspLinkRemoteIpAddrTable following the RowStatus textual convention. |
| cgspLinkRemoteIpAddrTable | 1.3.6.1.4.1.9.9.336.1.6.3 | not-accessible | A table that contains the remote IP addresses used to configure a particular Link. Entries are added to this table via cgspLinkRemoteIpAddrRowStatus in accordance with the RowStatus convention. | |
| cgspLinkRemoteIpAddrTableEntry | 1.3.6.1.4.1.9.9.336.1.6.3.1 | not-accessible | A list of remote IP addresses per Link. | |
| IPt cgspLinkRemoteIpAddrType | 1.3.6.1.4.1.9.9.336.1.6.3.1.2 | InetAddressType | read-create | This object contains the type of the local IP address used to create an association. |
| INE cgspLinkRemotePeerPort | 1.3.6.1.4.1.9.9.336.1.6.1.1.52 | InetPortNumber | read-create | When cgspLinkType is set to 'sctpIp' then this object contains the remote port number used to create the association supporting this link. When cgspLinkType is not set to 'sctpIp' then no significance is to be placed on this value. |
| ROW cgspLinkRowStatus | 1.3.6.1.4.1.9.9.336.1.6.1.1.89 | RowStatus | read-create | The object is used by a management station to create or delete the row entry in cgspLinkTable following the RowStatus textual convention. |
| U32 cgspLinkRxCongestionState | 1.3.6.1.4.1.9.9.336.1.6.1.1.96 | Unsigned32 | read-only | The Signalling link Received Side congestion status of this link. 0 abate, 1 onset is the received side congestion level |
| U32 cgspLinkSctpAssociation | 1.3.6.1.4.1.9.9.336.1.6.1.1.7 | Unsigned32 | read-only | Association Identifiers can be greater than 65,535. This object has been replaced by cgspLinkSctpAssociationId. |
| U32 cgspLinkSctpAssociationId | 1.3.6.1.4.1.9.9.336.1.6.1.1.90 | Unsigned32 | read-only | If the link type specified by cgspLinkType is 'sctpIp', this is the association identifier defined in the Stream Control Transmission Protocol(SCTP) MIB. Where value greater than zero indicates a valid association. The zero value indicates an association does not exist for this link. This value will always be set to zero one when cgspLinkType is not equal to the 'sctpIp' value. This object replaces cgspLinkSctpAssociation and allows association identifiers to be larger than 65,535. |
| cgspLinkset | 1.3.6.1.4.1.9.9.336.1.5 | |||
| T/F cgspLinksetAccountingGtt | 1.3.6.1.4.1.9.9.336.1.5.1.1.10 | TruthValue | read-create | This indicates if accounting for this linkset is enabled. 'true' Indicates that the accounting function is enabled for this linkset and is being accumulated in cgactMtp3Table. 'false' Indicates that the accounting function is disabled. |
| T/F cgspLinksetAccountingMtp3 | 1.3.6.1.4.1.9.9.336.1.5.1.1.9 | TruthValue | read-create | This indicates if accounting for this linkset is enabled. 'true' Indicates that the accounting function is enabled for this linkset and is being accumulated in cgactMtp3Table. 'false' Indicates that the accounting function is disabled. |
| U32 cgspLinksetActPriority | 1.3.6.1.4.1.9.9.336.1.5.1.1.14 | Unsigned32 | read-create | Defines the activation priority for linksets. The linksets with the lowest values will be activated first. If two or more linksets share the same values they will be activated in the order they were defined. |
| CIT cgspLinksetAdjacentDisplayPC | 1.3.6.1.4.1.9.9.336.1.5.1.1.5 | CItpTcDisplayPC | read-only | The point code to which this linkset is connected. |
| CIT cgspLinksetAdjacentInst | 1.3.6.1.4.1.9.9.336.1.5.1.1.20 | CItpTcNetworkName | read-only | When a linkset is used to carry traffic between different instances, this object contains the network name used as an index into the cgspInstanceTable table. In all other cases the object will contain the same network name as the source signalling point. |
| NUM cgspLinksetAdjacentPointCode | 1.3.6.1.4.1.9.9.336.1.5.1.1.4 | CItpTcPointCode | read-create | The point code to which this linkset is connected. |
| STR cgspLinksetDescription | 1.3.6.1.4.1.9.9.336.1.5.1.1.16 | SnmpAdminString | read-create | A textual description for the Signalling point. |
| STR cgspLinksetDisplayName | 1.3.6.1.4.1.9.9.336.1.5.1.1.15 | SnmpAdminString | read-create | A short identifier for each linkset. This value can be set by system administrator or defaults to the linkset name. |
| C32 cgspLinksetDurationInService | 1.3.6.1.4.1.9.9.336.1.5.1.1.12 | Counter32 | read-only | Time linkset was providing service related to Q752/Table 4.2. |
| C32 cgspLinksetDurationOutService | 1.3.6.1.4.1.9.9.336.1.5.1.1.13 | Counter32 | read-only | Time linkset was Out-of-Service as required for Q752/Table 4.2. |
| CIT cgspLinksetInboundAcl | 1.3.6.1.4.1.9.9.336.1.5.1.1.7 | CItpTcAclId | read-create | Packets are filtered against this access control list before they are passed to the routing function. A value of zero indicates that no access control list is present. |
| CIT cgspLinksetName | 1.3.6.1.4.1.9.9.336.1.5.1.1.1 | CItpTcLinksetId | not-accessible | The name of the linkset. |
| U32 cgspLinksetNumLinks | 1.3.6.1.4.1.9.9.336.1.5.1.1.11 | Unsigned32 | read-only | The number of links in this linkset. |
| CIT cgspLinksetOutboundAcl | 1.3.6.1.4.1.9.9.336.1.5.1.1.8 | CItpTcAclId | read-create | Packets are filtered against this access control list after they have passed through the routing function. A value of zero indicates that no access control list is present. |
| CGS cgspLinksetProfileName | 1.3.6.1.4.1.9.9.336.1.5.1.1.19 | CgspProfileName | read-create | When specified this object indicates which profile will be used to establish defaults for common configuration values like MTP2 and MTP3 timers. The null string is used to indicate that the linkset does not have a profile. |
| T/F cgspLinksetRotateSlsEnable | 1.3.6.1.4.1.9.9.336.1.5.1.1.17 | TruthValue | read-create | This defines whether signalling link selector(SLS) will be rotated. This option only applies to ANSI variant and will return false for all other variants. By default SLS rotation is enable by default for ANSI linksets. ANSI specifications state that SLS rotation should not be performed on C type linksets. This object can be used to disable SLS rotation. 'true' Indicates that SLS rotation is enable for this linkset. 'false' Indicates that SLS rotation is disable for this linkset. |
| U32 cgspLinksetRotateSlsShift | 1.3.6.1.4.1.9.9.336.1.5.1.1.18 | Unsigned32 | read-create | This value used to shift the signalling link selector(SLS) when rotation is enabled. This option only applies to ANSI variant and will return 0 all other variants. |
| ROW cgspLinksetRowStatus | 1.3.6.1.4.1.9.9.336.1.5.1.1.21 | RowStatus | read-create | The object is used by a management station to create or delete the row entry in cgspLinksetTable following the RowStatus textual convention. |
| CIT cgspLinksetSourceDisplayPC | 1.3.6.1.4.1.9.9.336.1.5.1.1.3 | CItpTcDisplayPC | read-only | The point code to which this linkset is connected. |
| NUM cgspLinksetSourcePointCode | 1.3.6.1.4.1.9.9.336.1.5.1.1.2 | CItpTcPointCode | read-create | The point code to which this linkset is connected. |
| INT cgspLinksetState | 1.3.6.1.4.1.9.9.336.1.5.1.1.6 | INTEGER | read-only | The list of possible linkset states. 'available' : Traffic may flow over this linkset 'shutdown' : This linkset has been forced to an unavailable state by an administrative action. 'unavailable': The linkset is currently unable to support traffic. Activation of this linkset will occur as required by protocol. |
| cgspLinksetTable | 1.3.6.1.4.1.9.9.336.1.5.1 | not-accessible | A table of linksets for this Signalling Point defined by this instance. | |
| cgspLinksetTableEntry | 1.3.6.1.4.1.9.9.336.1.5.1.1 | not-accessible | A list of Signalling Point linkset attributes for Signalling Point define by this instance. | |
| CGS cgspLinksetTimerNumber | 1.3.6.1.4.1.9.9.336.1.5.2.1.1 | CgspTimerNumbers | not-accessible | Index into table containing timer information. |
| ROW cgspLinksetTimerRowStatus | 1.3.6.1.4.1.9.9.336.1.5.2.1.3 | RowStatus | read-create | The object is used by a management station to create or delete the row entry in cgspLinksetTimerTable following the RowStatus textual convention. |
| cgspLinksetTimerTable | 1.3.6.1.4.1.9.9.336.1.5.2 | not-accessible | A table that contains the timer used to configure timer values specific to a particular linkset. Entries are added to this table via cgspLinksetTimerRowStatus in accordance with the RowStatus convention. | |
| cgspLinksetTimerTableEntry | 1.3.6.1.4.1.9.9.336.1.5.2.1 | not-accessible | This table is used to configure all MTP3 timer values that apply to linksets and links. The values apply to this linkset and links it c contains. | |
| CGS cgspLinksetTimerValue | 1.3.6.1.4.1.9.9.336.1.5.2.1.2 | CgspTimerValue | read-create | Value of timer selected by cgspLinksetTimerNumber object. |
| T/F cgspLinkSigLinkTest | 1.3.6.1.4.1.9.9.336.1.6.1.1.18 | TruthValue | read-create | Indicated if Signalling link test is enabled on this link. true : Signalling link test is enabled. false : Signalling link test not enabled. |
| CIT cgspLinkSlc | 1.3.6.1.4.1.9.9.336.1.6.1.1.1 | CItpTcLinkSLC | not-accessible | The Signalling Link Code for this link. |
| INT cgspLinkState | 1.3.6.1.4.1.9.9.336.1.6.1.1.3 | INTEGER | read-only | The list of possible links states. 'available' : Traffic may flow over this linkset 'failed' : Traffic management has detected a failure that prevents activating this linkset. 'shutdown' : This linkset has been forced to an unavailable state by an administrative action. 'unavailable': The linkset is currently unable to support traffic. Activation of this linkset will occur as required by protocol. |
| cgspLinkTable | 1.3.6.1.4.1.9.9.336.1.6.1 | not-accessible | A table of links for each Signalling Point. | |
| cgspLinkTableEntry | 1.3.6.1.4.1.9.9.336.1.6.1.1 | not-accessible | A list of signalling point link attributes. | |
| INT cgspLinkTcbcState | 1.3.6.1.4.1.9.9.336.1.6.1.1.64 | INTEGER | read-only | Changeback control State: 'undefined' - link is an undefined state. 'idle' - Link is available and idle. 'firstAttempt' - First attempt at changeback. 'secondAttempt' - Second attempt at changeback 'timeControlledDiversion' - Changeback using time controlled Diversion. |
| CGS cgspLinkTcocLocalBSNT | 1.3.6.1.4.1.9.9.336.1.6.1.1.62 | CgspSequenceNumber | read-only | The local backward sequence number to be transmitted. |
| CGS cgspLinkTcocRemoteBSNT | 1.3.6.1.4.1.9.9.336.1.6.1.1.63 | CgspSequenceNumber | read-only | The remote backward sequence number to be transmitted. |
| INT cgspLinkTcocState | 1.3.6.1.4.1.9.9.336.1.6.1.1.61 | INTEGER | read-only | Changeover control State: 'undefined' - Link is an undefined state. 'idle' - Link is available and idle. 'wait2' - Wait for MTP2 to initialize link. 'waitForAck' - Waiting for changeover acknowledgement. 'retrieving' - Packets are being retrieved from link. 'wait5' - Wait state when transitioning from idle state. 'wait7' - Delay to avoid message mis-sequencing on changeover 'wait8' - Wait state prior to processing changeover order or emergency changeover order events. |
| CGS cgspLinkTestResult | 1.3.6.1.4.1.9.9.336.1.6.1.1.88 | CgspLinkTestResults | read-only | This object provides information on result from signalling link test received on this link. |
| CGS cgspLinkTimerNumber | 1.3.6.1.4.1.9.9.336.1.6.2.1.1 | CgspTimerNumbers | not-accessible | Index into table containing timer information. |
| ROW cgspLinkTimerRowStatus | 1.3.6.1.4.1.9.9.336.1.6.2.1.3 | RowStatus | read-create | The object is used by a management station to create or delete the row entry in cgspLinkTimerTable following the RowStatus textual convention. |
| cgspLinkTimerTable | 1.3.6.1.4.1.9.9.336.1.6.2 | not-accessible | A table that contains the timer used to configure timer values specific to a particular Link. Entries are added to this table via cgspLinkTimerRowStatus in accordance with the RowStatus convention. | |
| cgspLinkTimerTableEntry | 1.3.6.1.4.1.9.9.336.1.6.2.1 | not-accessible | This table is used to configure all MTP3 timer values that apply to links. The values apply to a particular link. | |
| CGS cgspLinkTimerValue | 1.3.6.1.4.1.9.9.336.1.6.2.1.2 | CgspTimerValue | read-create | Value of timer selected by cgspLinkTimerNumber object. |
| C32 cgspLinkTransmittedLSSUs | 1.3.6.1.4.1.9.9.336.1.6.1.1.56 | Counter32 | read-only | The number of Link Status Signal Units sent on this link. |
| C32 cgspLinkTransmittedSIBs | 1.3.6.1.4.1.9.9.336.1.6.1.1.66 | Counter32 | read-only | The number of status indicator 'busy' link status signal units transmitted on this link. The SIB indicates that level two is congested at the transmitting Signalling point. |
| INT cgspLinkTsrcState | 1.3.6.1.4.1.9.9.336.1.6.1.1.60 | INTEGER | read-only | Signalling traffic management routing control state: 'undefined' - link is an undefined state 'idle' - traffic management is idle 'wait5' - traffic management is active and in the sending status phase |
| CIT cgspLinkType | 1.3.6.1.4.1.9.9.336.1.6.1.1.5 | CItpTcLinkType | read-create | The link type. |
| TIM cgspLinkUtilEndTimestamp | 1.3.6.1.4.1.9.9.336.1.6.4.1.4 | TimeStamp | read-only | This timestamp indicates when time period ended for this sample. |
| U32 cgspLinkUtilIndex | 1.3.6.1.4.1.9.9.336.1.6.4.1.1 | Unsigned32 | not-accessible | Index used to access historical link utilization information. Entry one corresponds to the most recent utilization window for the length of time specified by the cgspUtilSampleInterval object. Example of utilization history using default values. Current Time: 10:42 am Sample Interval: 300 seconds cgspLinkUtilIndex [1] Window from 10:36-10:41 [2] Window from 10:31-10:36 [3] Window from 10:26-10:31 . . [n] The index ranges from one to a maximum of sixty entries. The actual number of entries will depend on the implementation and available resources. |
| CGS cgspLinkUtilizationRcvd | 1.3.6.1.4.1.9.9.336.1.6.1.1.80 | CgspLinkUtilization | read-only | An estimate of the utilization of this link for traffic received on this link in the prior time period defined by the cgspUtilSampleInterval object. |
| CGS cgspLinkUtilizationSent | 1.3.6.1.4.1.9.9.336.1.6.1.1.85 | CgspLinkUtilization | read-only | An estimate of the utilization of this link for traffic sent on this link in the prior time period defined by the cgspUtilSampleInterval object. |
| T/F cgspLinkUtilNotifEnabled | 1.3.6.1.4.1.9.9.336.1.7.4 | TruthValue | read-write | The signalling point link utilization notification truth value. 'true' Indicates that the notification of link utilization has been enabled. That is, the notification generation is enabled. 'false' Indicates that the notification link utilization has been disabled. |
| CGS cgspLinkUtilRcvd | 1.3.6.1.4.1.9.9.336.1.6.4.1.2 | CgspLinkUtilization | read-only | An estimate of the utilization of this link for traffic received on this link in the time period defined by the cgspUtilSampleInterval object. |
| CGS cgspLinkUtilSent | 1.3.6.1.4.1.9.9.336.1.6.4.1.3 | CgspLinkUtilization | read-only | An estimate of the utilization of this link for traffic transmitted on this link in the time period defined by the cgspUtilSampleInterval object. |
| CGS cgspLinkUtilStateRcvd | 1.3.6.1.4.1.9.9.336.1.6.1.1.81 | CgspLinkUtilizationState | read-only | Link Utilization State for inbound traffic. |
| CGS cgspLinkUtilStateSent | 1.3.6.1.4.1.9.9.336.1.6.1.1.86 | CgspLinkUtilizationState | read-only | Link Utilization State for out bound traffic. |
| cgspLinkUtilTable | 1.3.6.1.4.1.9.9.336.1.6.4 | not-accessible | A table that contains a history of the cgspLinkUtilizationRcvd and cgspLinkUtilizationRcvd objects. In order to properly manage network capacity it is necessary to collect utilization information during short interval. These intervals are less than 5 minutes and can be as low as 1 minute. The number of links supported by a signalling point prevent polling each signalling point to collect information. This table is provided to allow an NMS to collect the information during a normal poll cycle. | |
| cgspLinkUtilTableEntry | 1.3.6.1.4.1.9.9.336.1.6.4.1 | not-accessible | A collection of entries used to store a history link utilization values. Values from cgspLinkUtilizationRcvd and cgspLinkUtilizationSent objects are saved in cgspLinkUtilRcvd and cgspLinkUtilSent. | |
| CGS cgspLinkUtilThresholdRcvd | 1.3.6.1.4.1.9.9.336.1.6.1.1.79 | CgspPercentThreshold | read-create | This object specifies the threshold used to to generate the ciscoGspLinkRcvdUtilChange notification. The value of zero indicates the threshold has not been defined at the link level and the value from the cgspLinksetUtilThresholdRcvd or cgspUtilThreshold objects will be used to generate the ciscoGspLinkRcvdUtilChange notification. |
| CGS cgspLinkUtilThresholdSent | 1.3.6.1.4.1.9.9.336.1.6.1.1.84 | CgspPercentThreshold | read-create | This object specifies the threshold used to generate the ciscoGspLinkRcvdUtilChange notification. The value of zero indicates the threshold has not been defined at the link level and the value from the cgspLinksetUtilThresholdRcvd or cgspUtilThreshold objects will be used to generate the ciscoGspLinkRcvdUtilChange notification. |
| G32 cgspLinkXmitQueueDepth | 1.3.6.1.4.1.9.9.336.1.6.1.1.8 | Gauge32 | read-only | Number of packets waiting to be sent over this link. |
| U32 cgspLinkXmitQueueDepthHigh | 1.3.6.1.4.1.9.9.336.1.6.1.1.9 | Unsigned32 | read-create | This is the maximum number of packets waiting to be sent over this link since the last time this value was reset as indicated by cgspLinkXmitQueueDepthHighRT. Resetting this object is achieved by setting this object to 0. Attempting to set this object to any other value will result in a wrongValue (SNMPv2c, SNMPv3) or badValue (SNMPv1). |
| TIM cgspLinkXmitQueueDepthHighRT | 1.3.6.1.4.1.9.9.336.1.6.1.1.10 | TimeStamp | read-only | This indicates when cgspLinkXmitQueueDepthHigh was last set to 0. |
| T/F cgspLnkStateChangeNotifEnabled | 1.3.6.1.4.1.9.9.336.1.7.2 | TruthValue | read-write | The signalling point link notification truth value. 'true' Indicates that ciscoGspLinkStateChange notification is to be generated when the state changes. That is, the notification generation is enabled. 'false' Indicates that ciscoGspLinkStateChange notification generation is disabled. |
| T/F cgspLsStateChangeNotifEnabled | 1.3.6.1.4.1.9.9.336.1.7.1 | TruthValue | read-write | The signalling point linkset notification truth value. 'true' Indicates that ciscoGspLinksetStateChange notification is to be generated when the state changes. That is, the notification generation is enabled. 'false' Indicates that ciscoGspLinksetStateChange notification generation is disabled. |
| CIT cgspMtp3SI | 1.3.6.1.4.1.9.9.336.1.3.3.1.1 | CItpTcServiceIndicator | not-accessible | The service indicator. |
| cgspNotificationsEnable | 1.3.6.1.4.1.9.9.336.1.7 | |||
| cgspNotificationsInfo | 1.3.6.1.4.1.9.9.336.1.8 | |||
| CGS cgspPlanCapacityDefault | 1.3.6.1.4.1.9.9.336.1.1.5 | CgspLinkCapacity | read-write | This object provides a default for value for links with a cgspLinkType='sctpIp'. For all other types of linkset this value is ignored. When a linkset based on SCTP/IP and the values for the cgspLinkPlanCapacityRcvd or cgspLinkPlanCapacitySent object are zero then this object will be used as the default. A value of zero indicates that a global default has not been specified. This object will be used in combination with cgspUtilSampleInterval, cgspUtilThreshold, cgspUtilThreshold and cgspLinkUtilThresholdRcvd to generate the ciscoGspLinkRcvdUtilChange notification. |
| cgspPointCode | 1.3.6.1.4.1.9.9.336.1.4 | |||
| NUM cgspPointCodeBin | 1.3.6.1.4.1.9.9.336.1.4.1.1.2 | CItpTcPointCode | not-accessible | The point code for this Signalling Point. |
| CIT cgspPointCodeDisplay | 1.3.6.1.4.1.9.9.336.1.4.1.1.4 | CItpTcDisplayPC | read-only | The point code for this Signalling Point. |
| CIT cgspPointCodeNi | 1.3.6.1.4.1.9.9.336.1.4.1.1.1 | CItpTcNetworkIndicator | not-accessible | The network Indicator for this pointcode. |
| ROW cgspPointCodeRowStatus | 1.3.6.1.4.1.9.9.336.1.4.1.1.5 | RowStatus | read-create | The object is used by a management station to create or delete the row entry in cgspPointCodeTable following the RowStatus textual convention. |
| cgspPointCodeTable | 1.3.6.1.4.1.9.9.336.1.4.1 | not-accessible | A table that contains a list of point code defined for the Signalling point defined by this instance. Entries are added to this table via cgspPointCodeRowStatus in accordance with the RowStatus convention. | |
| cgspPointCodeTableEntry | 1.3.6.1.4.1.9.9.336.1.4.1.1 | not-accessible | A list of Point codes for a signalling point defined by an instance. | |
| NUM cgspPointCodeType | 1.3.6.1.4.1.9.9.336.1.4.1.1.3 | CItpTcPointCodeType | read-create | The function of this point code. |
| cgspProfile | 1.3.6.1.4.1.9.9.336.1.2 | |||
| I32 cgspProfileMtp2BundleTimer | 1.3.6.1.4.1.9.9.336.1.2.1.1.3 | Integer32 | read-create | Bundle timer value. This value is used to control the bundling of SS7 packets as they are transported within the device. The value of zero indicates that MTP3 packets will not be bundled for transmission as they arrival for transmission at the MTP2 layer. A non-zero value specifies the maximum delay time used to collect MTP3 packets before they are transmitted by the MTP2 layer. |
| I32 cgspProfileMtp2SendQueueDepth | 1.3.6.1.4.1.9.9.336.1.2.1.1.4 | Integer32 | read-create | The maximum Queue depth allowed per link for MTP2 waiting to be transmitted. |
| CGS cgspProfileName | 1.3.6.1.4.1.9.9.336.1.2.1.1.1 | CgspProfileName | not-accessible | Name of the profile. |
| ROW cgspProfileRowStatus | 1.3.6.1.4.1.9.9.336.1.2.1.1.5 | RowStatus | read-create | The object is used by a management station to create or delete the row entry in cgspProfileTable following the RowStatus textual convention. |
| cgspProfileTable | 1.3.6.1.4.1.9.9.336.1.2.1 | not-accessible | A table that contains the Profiles of signalling points. Entries are added to this table via cgspProfileRowStatus in accordance with the RowStatus convention. | |
| cgspProfileTableEntry | 1.3.6.1.4.1.9.9.336.1.2.1.1 | not-accessible | A list of Profile attributes. Profiles are used to specify common configuration options for SS7 links without customizing each link. A profile is created with the specified values using this table and the cgspProfileTimerTable Table. The common values are applied to all links in a linkset by specifying the cgspLinksetProfileName on the linkset. | |
| CGS cgspProfileTimerNumber | 1.3.6.1.4.1.9.9.336.1.2.2.1.1 | CgspTimerNumbers | not-accessible | Index into table containing timer information. |
| ROW cgspProfileTimerRowStatus | 1.3.6.1.4.1.9.9.336.1.2.2.1.3 | RowStatus | read-create | The object is used by a management station to create or delete the row entry in cgspProfileTimerTable following the RowStatus textual convention. |
| cgspProfileTimerTable | 1.3.6.1.4.1.9.9.336.1.2.2 | not-accessible | A table that contains a profile of timers used to configure SS7 links. Entries are added to this table via cgspProfileTimerRowStatus in accordance with the RowStatus convention. | |
| cgspProfileTimerTableEntry | 1.3.6.1.4.1.9.9.336.1.2.2.1 | not-accessible | A list of ProfileTimer attributes. Profiles are used to specify common timer configuration options for SS7 links without customizing each link. A profile is created with the specified values using this table and the cgspProfileTable Table. The common values are applied to all links in a linkset by specifying the cgspLinksetProfileName on the linkset. | |
| CGS cgspProfileTimerValue | 1.3.6.1.4.1.9.9.336.1.2.2.1.2 | CgspTimerValue | read-create | Value of timer selected by cgspProfileTimerNumber object. |
| CGS cgspProfileVariant | 1.3.6.1.4.1.9.9.336.1.2.1.1.2 | CgspSS7Variant | read-create | The SS7 variant used to format data specified in this profile. |
| cgspScalars | 1.3.6.1.4.1.9.9.336.1.1 | |||
| U32 cgspUPUIntervalDuration | 1.3.6.1.4.1.9.9.336.1.8.1 | Unsigned32 | accessible-for-notify | Duration elapsed since the start of the cgspUPUNotifWindowTime interval. This duration value can range from 0 upto cgspUPUNotifWindowTime. For the notifications generated at the end of the interval, this value will be equal to cgspUPUNotifWindowTime. |
| T/F cgspUPUNotifEnabled | 1.3.6.1.4.1.9.9.336.1.7.6 | TruthValue | read-write | A control to enable or disable both ciscoGspUPUReceived and ciscoGspUPUTransmitted notifications as follows: 'true' Indicates that the ciscoGspUPUReceived and ciscoGspUPUTransmitted notification generation is enabled. 'false' Indicates that ciscoGspUPUReceived and ciscoGspUPUTransmitted notification generation is disabled. |
| I32 cgspUPUNotifWindowTime | 1.3.6.1.4.1.9.9.336.1.1.7 | Integer32 | read-write | This object specifies the time interval used to monitor the ciscoGspUPUReceived and ciscoGspUPUTransmitted notifications for specific user part and signalling point instance. The first occurrence of ciscoGspUPUReceived and ciscoGspUPUTransmitted notifications are sent and the further occurrences of notifications in this interval are suppressed. At the end of this interval, a notification is sent with total number of UPU MSUs transmitted or received during this interval. |
| CGS cgspUtilAbateDelta | 1.3.6.1.4.1.9.9.336.1.1.4 | CgspPercentThreshold | read-write | This object allows the falling threshold to be lower than the rising threshold when calculating whether to generate the ciscoGspLinkRcvdUtilChange or ciscoGspLinkSentUtilChange notifications. This is done to prevent generating notifications for slight changes in traffic. |
| NUM cgspUtilSampleInterval | 1.3.6.1.4.1.9.9.336.1.1.2 | CgspSampleInterval | read-write | This object specifies the time interval used to monitor the utilization of SS7 links. This object in combination with cgspUtilThreshold, cgspLinkPlanCapacitySent and cgspLinkPlanCapacityRcvd will be used to calculate utilization of SS7 links. Changes to the polling interval will take effect after the completion of the current sample interval. |
| CGS cgspUtilThreshold | 1.3.6.1.4.1.9.9.336.1.1.3 | CgspPercentThreshold | read-write | This object specifies the threshold of usage for all SS7 links in SP. This object is used to determine when to generate the ciscoGspLinkRcvdUtilChange or ciscoGspLinkSentUtilChange notifications. A value of zero indicates that no default threshold is specified. Therefore, only links with non-zero values for cgspLinkUtilThresholdRcvd or cgspLinkUtilThresholdSent will generate notifications based on link utilization. Changes to the utilization threshold will take effect at the end of the current interval. |
| NTF ciscoGspCongestionChange | 1.3.6.1.4.1.9.9.336.0.3 | The notification generated when a link changes to a new congestion level as specified by cgspLinkCongestionState object for Transmission Side congestion. | ||
| ciscoGspInstanceGroup | 1.3.6.1.4.1.9.9.336.2.2.3 | Instance of Signalling Point. | ||
| ciscoGspInstSccpWrrGroup | 1.3.6.1.4.1.9.9.336.2.2.24 | SCCP GTT weighted loadshare group. | ||
| ciscoGspInstTimerGroup | 1.3.6.1.4.1.9.9.336.2.2.4 | Timers defined for each Instance of Signalling Point. | ||
| ciscoGspInstUPUGroup | 1.3.6.1.4.1.9.9.336.2.2.20 | SS7 Destination and Service Indicator group. | ||
| NTF ciscoGspIsolation | 1.3.6.1.4.1.9.9.336.0.6 | This notification indicates the instance specified by cgspInstDisplayName and cgspInstDescription has become isolated. All linkset used to connect MTP3 node (instance) are unavailable. Isolation is ended when any linkset supported by this instance reaches the active state. | ||
| ciscoGspLinkGroup | 1.3.6.1.4.1.9.9.336.2.2.8 | SP link objects. | ||
| ciscoGspLinkGroupRev1 | 1.3.6.1.4.1.9.9.336.2.2.14 | SP link objects. | ||
| ciscoGspLinkGroupSup1 | 1.3.6.1.4.1.9.9.336.2.2.17 | Additional Link statistics. | ||
| NTF ciscoGspLinkRcvdUtilChange | 1.3.6.1.4.1.9.9.336.0.4 | The notification provide is generated when the cgspLinkUtilStateRcvd changes states. | ||
| ciscoGspLinkRemoteIpGroup | 1.3.6.1.4.1.9.9.336.2.2.10 | Remote IP addresses for each Link. | ||
| NTF ciscoGspLinkSentUtilChange | 1.3.6.1.4.1.9.9.336.0.5 | The notification provide is generated when the cgspLinkUtilStateSent changes states. | ||
| ciscoGspLinksetGroup | 1.3.6.1.4.1.9.9.336.2.2.6 | linkset objects . | ||
| NTF ciscoGspLinksetStateChange | 1.3.6.1.4.1.9.9.336.0.1 | The notification generated when a linkset changes to a new state. The value of cgspLinksetState indicates the new state. | ||
| ciscoGspLinksetTimerGroup | 1.3.6.1.4.1.9.9.336.2.2.7 | Timers defined for each Linkset. | ||
| NTF ciscoGspLinkStateChange | 1.3.6.1.4.1.9.9.336.0.2 | The notification generated when a link changes to a new state. The value of cgspLinkState indicates the new state. | ||
| ciscoGspLinkTableEntryGroupSup1 | 1.3.6.1.4.1.9.9.336.2.2.25 | cgspLinkRxCongestionstate object for Received side congestion | ||
| ciscoGspLinkTimerGroup | 1.3.6.1.4.1.9.9.336.2.2.9 | Timers defined for each Link. | ||
| ciscoGspLinkUtilGroup | 1.3.6.1.4.1.9.9.336.2.2.11 | Utilization history for each Link. | ||
| ciscoGspMIB | 1.3.6.1.4.1.9.9.336 | The MIB for managing Signalling Points and its associated messages transported over Signalling System No. 7 (SS7) Network via Cisco IP Transfer Point. This MIB replaces the CISCO-ITP-SP-MIB and provide support multiple instances of a signalling point within same configuration. The Cisco IP Transfer Point (ITP) is a hardware and software solution that transports SS7 traffic using IP. Each ITP node provides function similar to SS7 Signalling point. The relevant ITU documents describing this technology is the ITU Q series, including ITU Q.700: Introduction to CCITT Signalling System No. 7 and ITU Q.701 Functional description of the message transfer part (MTP) of Signalling System No. 7. This MIB models the GSP as follows: Abbreviations: AERM - Alignment Error Rate Monitor CLLI - Common-Language Location Identification DPC - Destination Point Code GSP - Gateway Signalling Point HSL - High Speed Link (ATM based) LLSC - link set control LSAC - Signalling link activity control LSDA - Signalling data link allocation LSLA - Signalling link activation LSLD - Signalling link deactivation LSLR - Signalling link restoration LSSU - Link Status Signal Unit LSTA - Signalling terminal allocation MTP - Message Transport Protocol MTP2 - Layer 2 of Message Transport Protocol MTP3 - Layer 3 of Message Transport Protocol NTT - The Japanese Nippon Telephone & Telegraph OPC - Originating Point Code PC - Point Code RTN - RouteTableName SCTP - Stream Transmission Protocol(RFC 2960) SIB - Status Indicator Busy SLT - Signalling Link Test SLTA - Signalling Link Test Acknowledgement SP - Signalling Point SS7 - System No. 7 (SS7) Network SUERM - Signal Unit Error Rate Monitor TCBC - Changeback control TCOC - Changeover control TCRC - Controlled rerouting control TFRC - Forced rerouting control TLAC - Link availability control TPRC - Signalling point restart control TRCC - Signalling route set congestion control TSFC - Signalling traffic flow control TSRC - Signalling routing control TTC - The Japanese Telecommunications Technology Committee WRR - Weighted round robin | ||
| ciscoGspMIBCompliance | 1.3.6.1.4.1.9.9.336.2.1.1 | The compliance statement for entities which implement the CISCO-ITP-GSP-MIB | ||
| ciscoGspMIBComplianceRev1 | 1.3.6.1.4.1.9.9.336.2.1.2 | The compliance statement for entities which implement the CISCO-ITP-GSP-MIB | ||
| ciscoGspMIBComplianceRev2 | 1.3.6.1.4.1.9.9.336.2.1.3 | The compliance statement for entities which implement the CISCO-ITP-GSP-MIB | ||
| ciscoGspMIBComplianceRev3 | 1.3.6.1.4.1.9.9.336.2.1.4 | The compliance statement for entities which implement the CISCO-ITP-GSP-MIB | ||
| ciscoGspMIBComplianceRev4 | 1.3.6.1.4.1.9.9.336.2.1.5 | The compliance statement for entities which implement the CISCO-ITP-GSP-MIB | ||
| ciscoGspMIBComplianceRev5 | 1.3.6.1.4.1.9.9.336.2.1.6 | The compliance statement for entities which implement the CISCO-ITP-GSP-MIB | ||
| ciscoGspMIBCompliances | 1.3.6.1.4.1.9.9.336.2.1 | |||
| ciscoGspMIBConform | 1.3.6.1.4.1.9.9.336.2 | |||
| ciscoGspMIBGroups | 1.3.6.1.4.1.9.9.336.2.2 | |||
| ciscoGspMIBNotifs | 1.3.6.1.4.1.9.9.336.0 | |||
| ciscoGspMIBObjects | 1.3.6.1.4.1.9.9.336.1 | |||
| ciscoGspNotificationsEnableGroup | 1.3.6.1.4.1.9.9.336.2.2.12 | SP enable notification objects. | ||
| ciscoGspNotificationsEnableGroupSup1 | 1.3.6.1.4.1.9.9.336.2.2.15 | Isolation notification enable. | ||
| ciscoGspNotificationsEnableGroupSup2 | 1.3.6.1.4.1.9.9.336.2.2.22 | UPU notifications enable. | ||
| ciscoGspNotificationsGroup | 1.3.6.1.4.1.9.9.336.2.2.13 | SP notifications. | ||
| ciscoGspNotificationsGroupSup1 | 1.3.6.1.4.1.9.9.336.2.2.16 | Isolation notification. | ||
| ciscoGspNotificationsGroupSup2 | 1.3.6.1.4.1.9.9.336.2.2.23 | Adjacent SP accessibility notification, UPU sent and received notifications. | ||
| ciscoGspNotificationsGroupSup3 | 1.3.6.1.4.1.9.9.336.2.2.26 | Link Receive side congestion notication. | ||
| ciscoGspNotificationsInfoGroup | 1.3.6.1.4.1.9.9.336.2.2.21 | Notifications Info Group. | ||
| ciscoGspPointCodeGroup | 1.3.6.1.4.1.9.9.336.2.2.5 | Pointcode defined for each Instance of Signalling Point. | ||
| ciscoGspProfileGroup | 1.3.6.1.4.1.9.9.336.2.2.2 | Profile Group for Gateway Signalling Point. | ||
| NTF ciscoGspRxCongestionChange | 1.3.6.1.4.1.9.9.336.0.10 | The notification generated when a link changes to a new congestion level as specified by cgspLinkRxCongestionstate object for Received side congestion | ||
| ciscoGspScalarsGroup | 1.3.6.1.4.1.9.9.336.2.2.1 | Scalars Group for Gateway Signalling Point. | ||
| ciscoGspScalarsGroupSup1 | 1.3.6.1.4.1.9.9.336.2.2.18 | Scalar Group supplements. | ||
| NTF ciscoGspUPUReceived | 1.3.6.1.4.1.9.9.336.0.8 | The notification is generated when an UPU MSU is received from a remote signalling point, for a specific instance and user part for the first time in the configured cgspUPUNotifWindowTime. For cases when there is a non-zero number of UPU MSUs received, this notification will be sent at the end of the cgspUPUNotifWindowTime interval, with cgspIntervalUPUs indicating the total count of UPU MSUs received for that specific instance and user part during the entire cgspUPUNotifWindowTime interval Q752/5.6. | ||
| NTF ciscoGspUPUTransmitted | 1.3.6.1.4.1.9.9.336.0.9 | The notification is generated when an UPU MSU is transmitted to a remote signalling point, for a specific instance and user part for the first time in the configured cgspUPUNotifWindowTime. For cases when there is a non-zero number of UPU MSUs received, this notification will be sent at the end of the cgspUPUNotifWindowTime interval, with cgspIntervalUPUs indicating the total count of UPU MSUs transmitted for that specific instance and user part during the entire cgspUPUNotifWindowTime interval Q752/5.7. |
FAQ
How can CISCO-ITP-GSP-MIB help spot an overloaded SS7 signaling point on a Cisco ITP?
It exposes utilization sampling and threshold objects (cgspUtilSampleInterval, cgspUtilThreshold) for the signaling point, acting like a CPU or link-utilization indicator so a carrier NOC can be alerted when the SS7 signaling function is approaching capacity.
What does this MIB provide for fault detection on Cisco IP Transfer Points?
Its cgspEventSequenceNumber object and the ciscoGspMIBNotifs notification subtree surface fault conditions on the signaling point, letting carriers track SS7 signaling faults as ITP nodes interconnect SS7 networks with an IP core.
RFC description
Cisco IP Transfer Point Gateway Signalling Point MIB for managing SS7 signalling points over IP.
Start monitoring Cisco IP Transfer Point (ITP) SS7 signaling gateway (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.