ZTE-AN-INTERFACE-STATS-MIB

All MIBs › ZTE-AN-INTERFACE-STATS-MIB

Organization: ZTE Corporation

Last Updated: 2015-10-20

Category: ZTE Access Node (ZTE-AN) Management

Description: Provides ZTE access node interface traffic statistics for bandwidth utilization monitoring.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ZTE-AN-INTERFACE-STATS-MIB?

ZTE-AN-INTERFACE-STATS-MIB is a ZTE Corporation vendor-specific MIB that provides detailed interface performance statistics for ZTE Access Node (AN) broadband access equipment, covering Ethernet ports, bridge ports, LAG interfaces, VLANs, and PVC interfaces. Its largest table, zxAnEthIfCurrStatsTable (indexed by the standard ifIndex), exposes dozens of Counter64 fields covering basic traffic volume (zxAnEthIfInOctets/OutOctets, InPkts/OutPkts, and unicast/multicast/broadcast breakdowns), error conditions (zxAnEthIfFcsErrors, zxAnEthIfAlignmentErrors, InCrcErrPkts/OutCrcErrPkts, InErrPkts/OutErrPkts), collision statistics (zxAnEthIfOutCollisions, SingleCollisions, MultipleCollisions), oversized/undersized/fragment/jabber packet counts, a full packet-size distribution histogram (64 octets up through 1024-1518 octets), and a zxAnEthIfLinkStatusChanges counter plus a zxAnEthIfReset control object. A separate zxAnPvcIfStatsGlobalMode scalar lets an operator globally start or stop statistics collection across all PVC interfaces at once (allStarted/allStopped/invalid). Per the source module's own outline, it also defines analogous statistics groups for bridge ports, LAG interfaces, interface rate/bandwidth utilization, VLAN and SVLAN/CVLAN traffic, and current (in-progress) performance windows, making it ZTE's counterpart to the standard IF-MIB/EtherLike-MIB but scoped to access-node hardware. It depends on IF-MIB for ifIndex, HC-PerfHist-TC-MIB for high-capacity current-count conventions, and ZTE-AN-SMI/ZTE-AN-IF-MIB/ZTE-AN-TC-MIB for its registration point and VLAN/sub-interface index types. It is deployed on ZTE Access Node broadband access equipment, and operators evaluating a ZTE-AN-INTERFACE-STATS-MIB MIB deployment watch error and collision counters to catch degrading subscriber-facing Ethernet links.

IPNetwork Monitor allows you to monitor SNMP objects defined in ZTE-AN-INTERFACE-STATS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ZTE Access Node (AN) broadband access / DSLAM-class equipment

Monitoring Examples

An operator polls zxAnEthIfFcsErrors, zxAnEthIfAlignmentErrors, and zxAnEthIfOutCollisions for a subscriber-facing Ethernet port on the access node to check physical-layer health; a climbing zxAnEthIfLinkStatusChanges counter alongside rising FCS error counts would indicate a flapping or degrading copper/fiber link to that subscriber.

What Can Be Monitored

Ethernet port traffic counters (octets, unicast/multicast/broadcast packets)
FCS and alignment error counters
collision statistics (single/multiple)
oversized/undersized/fragment/jabber packet counts
packet-size distribution histogram
link status change counter

Imported Objects

From HC-PerfHist-TC-MIB

HCPerfCurrentCount

From IF-MIB

ifIndex

OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus
TEXTUAL-CONVENTION
TruthValue

From ZTE-AN-IF-MIB

zxAnSubIfIndex

OBJECT-TYPE

From ZTE-AN-SMI

zxAnInterface

OBJECT-IDENTITY

From ZTE-AN-TC-MIB

VlanId

How to Use in IPNetwork Monitor

Example using zxAnEthIfInOctets OID:

Select a ZTE Access Node (AN) broadband access / DSLAM-class equipment (Ethernet/bridge/LAG/VLAN traffic-statistics status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type zxAnEthIfInOctets into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The total number of octets received on the interface, including framing characters. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
zxAnInterfaceStatsMib	1.3.6.1.4.1.3902.1082.30.31			The MIB module for the Performance Management of ZTE Access Node interface.
zxAnIfPerfGlobalObjects	1.3.6.1.4.1.3902.1082.30.31.1
INT zxAnPvcIfStatsGlobalMode	1.3.6.1.4.1.3902.1082.30.31.1.1	INTEGER	read-write	The global mode of PVC interface statistics. allStarted(1): Statistics of all the PVC interfaces are started. allStopped(2): Statistics of all the PVC interfaces are stopped. invalid(3): The global mode is invalid. Only statistics of the PVC interfaces in zxAnPvcIfCurrStatsTable are started.
zxAnIfPerfObjects	1.3.6.1.4.1.3902.1082.30.31.2
zxAnEthIfCurrStatsTable	1.3.6.1.4.1.3902.1082.30.31.2.2		not-accessible	Current performance data table of interfaces.
zxAnEthIfCurrStatsEntry	1.3.6.1.4.1.3902.1082.30.31.2.2.1		not-accessible	Current performance data entry of interfaces.
C64 zxAnEthIfInOctetsEx	1.3.6.1.4.1.3902.1082.30.31.2.2.1.1	Counter64	read-only	The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnEthIfInPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.2	Counter64	read-only	The total number of packets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnEthIfInUcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.3	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnEthIfInMcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.4	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnEthIfInBcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.5	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnEthIfInOversizedPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.6	Counter64	read-only	The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed.
C64 zxAnEthIfInUndersizedPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.7	Counter64	read-only	The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
C64 zxAnEthIfOutOctets	1.3.6.1.4.1.3902.1082.30.31.2.2.1.8	Counter64	read-only	The total number of octets transmitted out of the interface, including framing characters.
C64 zxAnEthIfOutPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.9	Counter64	read-only	The total number of packets transmitted out of the interface, including framing characters.
C64 zxAnEthIfOutUcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.10	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnEthIfOutMcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.11	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime
C64 zxAnEthIfOutBcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.12	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnEthIfOutPausePkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.13	Counter64	read-only	A count of MAC Control frames transmitted on this interface with an opcode indicating the PAUSE operation. This counter does not increment when the interface is operating in half-duplex mode. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCOutPauseFrames object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnEthIfOutDiscardPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.14	Counter64	read-only	The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnEthIfOutCollisions	1.3.6.1.4.1.3902.1082.30.31.2.2.1.15	Counter64	read-only	A count of frames that are involved in out collision and are subsequently transmitted successfully. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnEthIfSingleCollisions	1.3.6.1.4.1.3902.1082.30.31.2.2.1.16	Counter64	read-only	A count of frames that are involved in a single collision, and are subsequently transmitted successfully. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsMultipleCollisionFrames object. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnEthIfMultipleCollisions	1.3.6.1.4.1.3902.1082.30.31.2.2.1.17	Counter64	read-only	A count of frames that are involved in more than one collision and are subsequently transmitted successfully. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnEthIfFcsErrors	1.3.6.1.4.1.3902.1082.30.31.2.2.1.18	Counter64	read-only	A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. This count does not include frames received with frame-too-long or frame-too-short error. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. Note: Coding errors detected by the physical layer for speeds above 10 Mb/s will cause the frame to fail the FCS check. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsFCSErrors object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnEthIfAlignmentErrors	1.3.6.1.4.1.3902.1082.30.31.2.2.1.19	Counter64	read-only	A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. This counter does not increment for group encoding schemes greater than 4 bits per group. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsAlignmentErrors object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnEthIfInCrcErrPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.20	Counter64	read-only	The total number of CRC errored packets received on the interface.
C64 zxAnEthIfInDiscardPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.21	Counter64	read-only	The total number of discarded packets received on the interface.
C64 zxAnEthIfInErrPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.22	Counter64	read-only	The total number of errored packets received on the interface.
C64 zxAnEthIfOutErrPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.23	Counter64	read-only	The total number of errored packets that could not be transmitted from the interface because of errors.
C32 zxAnEthIfLinkStatusChanges	1.3.6.1.4.1.3902.1082.30.31.2.2.1.24	Counter32	read-only	The total number of the link status changes on the interface. The total number starts from zero and is increased when the link status changes from up to down, or from down to up.
C64 zxAnEthIfInDropEvents	1.3.6.1.4.1.3902.1082.30.31.2.2.1.25	Counter64	read-only	The total number of events in which packets received were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected.
C64 zxAnEthIfOutDropEvents	1.3.6.1.4.1.3902.1082.30.31.2.2.1.26	Counter64	read-only	The total number of events in which packets transmitted were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected.
C64 zxAnEthIfOutCrcErrPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.27	Counter64	read-only	The total number of CRC errored packets transmitted out of the interface.
C64 zxAnEthIfOutOversizedPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.28	Counter64	read-only	The total number of packets transmitted that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed.
C64 zxAnEthIfOutUndersizedPkts	1.3.6.1.4.1.3902.1082.30.31.2.2.1.29	Counter64	read-only	The total number of packets transmitted that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
C64 zxAnEthIfInFragments	1.3.6.1.4.1.3902.1082.30.31.2.2.1.30	Counter64	read-only	The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
C64 zxAnEthIfOutFragments	1.3.6.1.4.1.3902.1082.30.31.2.2.1.31	Counter64	read-only	The total number of packets transmitted that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
C64 zxAnEthIfInJabbers	1.3.6.1.4.1.3902.1082.30.31.2.2.1.32	Counter64	read-only	The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). Note that this definition of jabber is different than the definition in IEEE-802.3 section 8.2.1.5 (10BASE5) and section 10.3.1.4 (10BASE2). These documents define jabber as the condition where any packet exceeds 20 ms. The allowed range to detect jabber is between 20 ms and 150 ms.
C64 zxAnEthIfOutJabbers	1.3.6.1.4.1.3902.1082.30.31.2.2.1.33	Counter64	read-only	The total number of packets transmitted that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). Note that this definition of jabber is different than the definition in IEEE-802.3 section 8.2.1.5 (10BASE5) and section 10.3.1.4 (10BASE2). These documents define jabber as the condition where any packet exceeds 20 ms. The allowed range to detect jabber is between 20 ms and 150 ms.
C64 zxAnEthIfInPkts64Octets	1.3.6.1.4.1.3902.1082.30.31.2.2.1.34	Counter64	read-only	The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits but including FCS octets).
C64 zxAnEthIfOutPkts64Octets	1.3.6.1.4.1.3902.1082.30.31.2.2.1.35	Counter64	read-only	The total number of packets (including bad packets) transmitted that were 64 octets in length (excluding framing bits but including FCS octets).
C64 zxAnEthIfInPkts65to127Octets	1.3.6.1.4.1.3902.1082.30.31.2.2.1.36	Counter64	read-only	The total number of packets (including bad packets) received that were between 65 and 127 octets in length (excluding framing bits but including FCS octets).
C64 zxAnEthIfOutPkts65to127Octets	1.3.6.1.4.1.3902.1082.30.31.2.2.1.37	Counter64	read-only	The total number of packets (including bad packets) transmitted that were between 65 and 127 octets in length (excluding framing bits but including FCS octets).
C64 zxAnEthIfInPkts128to255Octets	1.3.6.1.4.1.3902.1082.30.31.2.2.1.38	Counter64	read-only	The total number of packets (including bad packets) received that were between 128 and 255 octets in length (excluding framing bits but including FCS octets).
C64 zxAnEthIfOutPkts128to255Octets	1.3.6.1.4.1.3902.1082.30.31.2.2.1.39	Counter64	read-only	The total number of packets (including bad packets) transmitted that were between 128 and 255 octets in length (excluding framing bits but including FCS octets).
C64 zxAnEthIfInPkts256to511Octets	1.3.6.1.4.1.3902.1082.30.31.2.2.1.40	Counter64	read-only	The total number of packets (including bad packets) received that were between 256 and 511 octets in length (excluding framing bits but including FCS octets).
C64 zxAnEthIfOutPkts256to511Octets	1.3.6.1.4.1.3902.1082.30.31.2.2.1.41	Counter64	read-only	The total number of packets (including bad packets) transmitted that were between 256 and 511 octets in length (excluding framing bits but including FCS octets).
C64 zxAnEthIfInPkts512to1023Octets	1.3.6.1.4.1.3902.1082.30.31.2.2.1.42	Counter64	read-only	The total number of packets (including bad packets) received that were between 512 and 1023 octets in length (excluding framing bits but including FCS octets).
C64 zxAnEthIfOutPkts512to1023Octets	1.3.6.1.4.1.3902.1082.30.31.2.2.1.43	Counter64	read-only	The total number of packets (including bad packets) transmitted that were between 512 and 1023 octets in length (excluding framing bits but including FCS octets).
C64 zxAnEthIfInPkts1024to1518Octets	1.3.6.1.4.1.3902.1082.30.31.2.2.1.44	Counter64	read-only	The total number of packets (including bad packets) received that were between 1024 and 1518 octets in length (excluding framing bits but including FCS octets).
C64 zxAnEthIfOutPkts1024to1518Octets	1.3.6.1.4.1.3902.1082.30.31.2.2.1.45	Counter64	read-only	The total number of packets (including bad packets) transmitted that were between 1024 and 1518 octets in length (excluding framing bits but including FCS octets).
INT zxAnEthIfReset	1.3.6.1.4.1.3902.1082.30.31.2.2.1.100	INTEGER	read-write	Clear all the current performance variables. When get this When get this variable, always return 1.
zxAnBrgIfCurrStatsTable	1.3.6.1.4.1.3902.1082.30.31.2.3		not-accessible	Current performance data table of interfaces.
zxAnBrgIfCurrStatsEntry	1.3.6.1.4.1.3902.1082.30.31.2.3.1		not-accessible	Current performance data entry of interfaces.
C64 zxAnBrgIfInOctets	1.3.6.1.4.1.3902.1082.30.31.2.3.1.1	Counter64	read-only	The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnBrgIfInUcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.3.1.2	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnBrgIfInMcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.3.1.3	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnBrgIfInBcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.3.1.4	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnBrgIfOutOctets	1.3.6.1.4.1.3902.1082.30.31.2.3.1.5	Counter64	read-only	The total number of octets transmitted out of the interface, including framing characters.
C64 zxAnBrgIfOutUcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.3.1.6	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnBrgIfOutMcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.3.1.7	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime
C64 zxAnBrgIfOutBcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.3.1.8	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnBrgIfInDiscardPkts	1.3.6.1.4.1.3902.1082.30.31.2.3.1.9	Counter64	read-only	The total number of received discarded packets.
C64 zxAnBrgIfOutDiscardPkts	1.3.6.1.4.1.3902.1082.30.31.2.3.1.10	Counter64	read-only	The total number of transmitted discarded packets.
INT zxAnBrgIfReset	1.3.6.1.4.1.3902.1082.30.31.2.3.1.100	INTEGER	read-write	Clear all the current performance variables. When get this variable, always return 1.
zxAnLagIfCurrStatsTable	1.3.6.1.4.1.3902.1082.30.31.2.4		not-accessible	Current performance data table of LAG.
zxAnLagIfCurrStatsEntry	1.3.6.1.4.1.3902.1082.30.31.2.4.1		not-accessible	Current performance data entry of LAG.
C64 zxAnLagIfInPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.1	Counter64	read-only	The total number of packets received on the LAG.
C64 zxAnLagIfOutPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.2	Counter64	read-only	The total number of packets transmitted on the LAG.
C64 zxAnLagIfInOctets	1.3.6.1.4.1.3902.1082.30.31.2.4.1.3	Counter64	read-only	The total number of octets received on the LAG.
C64 zxAnLagIfOutOctets	1.3.6.1.4.1.3902.1082.30.31.2.4.1.4	Counter64	read-only	The total number of octets transmitted on the LAG.
C64 zxAnLagIfInUcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.5	Counter64	read-only	The total number of unicast packets received on the LAG.
C64 zxAnLagIfOutUcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.6	Counter64	read-only	The total number of unicast packets transmitted on the LAG.
C64 zxAnLagIfInMcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.7	Counter64	read-only	The total number of multicast packets received on the LAG.
C64 zxAnLagIfOutMcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.8	Counter64	read-only	The total number of multicast packets transmitted on the LAG.
C64 zxAnLagIfInBcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.9	Counter64	read-only	The total number of broadcast packets received on the LAG.
C64 zxAnLagIfOutBcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.10	Counter64	read-only	The total number of broadcast packets transmitted on the LAG.
C64 zxAnLagIfInErrPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.11	Counter64	read-only	The total number of error packets received on the LAG.
C64 zxAnLagIfOutErrPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.12	Counter64	read-only	The total number of error packets transmitted on the LAG.
C64 zxAnLagIfInPkts64Octets	1.3.6.1.4.1.3902.1082.30.31.2.4.1.13	Counter64	read-only	The total number of packets received that were 64 octets in length on the LAG.
C64 zxAnLagIfOutPkts64Octets	1.3.6.1.4.1.3902.1082.30.31.2.4.1.14	Counter64	read-only	The total number of packets transmitted that were 64 octets in length on the LAG.
C64 zxAnLagIfInPkts65to127Octets	1.3.6.1.4.1.3902.1082.30.31.2.4.1.15	Counter64	read-only	The total number of packets received that were between 65 and 127 octets in length on the LAG.
C64 zxAnLagIfOutPkts65to127Octets	1.3.6.1.4.1.3902.1082.30.31.2.4.1.16	Counter64	read-only	The total number of packets transmitted that were between 65 and 127 octets in length on the LAG.
C64 zxAnLagIfInPkts128to255Octets	1.3.6.1.4.1.3902.1082.30.31.2.4.1.17	Counter64	read-only	The total number of packets received that were between 128 and 255 octets in length on the LAG.
C64 zxAnLagIfOutPkts128to255Octets	1.3.6.1.4.1.3902.1082.30.31.2.4.1.18	Counter64	read-only	The total number of packets transmitted that were between 128 and 255 octets in length on the LAG.
C64 zxAnLagIfInPkts256to511Octets	1.3.6.1.4.1.3902.1082.30.31.2.4.1.19	Counter64	read-only	The total number of packets received that were between 256 and 511 octets in length on the LAG.
C64 zxAnLagIfOutPkts256to511Octets	1.3.6.1.4.1.3902.1082.30.31.2.4.1.20	Counter64	read-only	The total number of packets transmitted that were between 256 and 511 octets in length on the LAG.
C64 zxAnLagIfInPkts512to1023Octets	1.3.6.1.4.1.3902.1082.30.31.2.4.1.21	Counter64	read-only	The total number of packets received that were between 512 and 1023 octets in length on the LAG.
C64 zxAnLagIfOutPkts512to1023Octets	1.3.6.1.4.1.3902.1082.30.31.2.4.1.22	Counter64	read-only	The total number of packets transmitted that were between 512 and 1023 octets in length on the LAG.
C64 zxAnLagIfInPkts1024to1518Octets	1.3.6.1.4.1.3902.1082.30.31.2.4.1.23	Counter64	read-only	The total number of packets received that were between 1024 and 1518 octets in length on the LAG.
C64 zxAnLagIfOutPkts1024to1518Octets	1.3.6.1.4.1.3902.1082.30.31.2.4.1.24	Counter64	read-only	The total number of packets transmitted that were between 1024 and 1518 octets in length on the LAG.
C64 zxAnLagIfInOversizedPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.25	Counter64	read-only	The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed.
C64 zxAnLagIfOutOversizedPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.26	Counter64	read-only	The total number of packets transmitted that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed.
C64 zxAnLagIfInUndersizedPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.27	Counter64	read-only	The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
C64 zxAnLagIfOutUndersizedPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.28	Counter64	read-only	The total number of packets transmitted that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
C64 zxAnLagIfInDiscardPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.29	Counter64	read-only	The total number of discarded packets received on the LAG interface.
C64 zxAnLagIfOutDiscardPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.30	Counter64	read-only	The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnLagIfInCrcErrPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.31	Counter64	read-only	The total number of CRC errored packets received on the LAG interface.
C64 zxAnLagIfOutCrcErrPkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.32	Counter64	read-only	The total number of CRC errored packets transmitted out of the LAG interface.
C64 zxAnLagIfInDropEvents	1.3.6.1.4.1.3902.1082.30.31.2.4.1.33	Counter64	read-only	The total number of events in which packets received were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected.
C64 zxAnLagIfOutDropEvents	1.3.6.1.4.1.3902.1082.30.31.2.4.1.34	Counter64	read-only	The total number of events in which packets transmitted were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected.
C64 zxAnLagIfInFragments	1.3.6.1.4.1.3902.1082.30.31.2.4.1.35	Counter64	read-only	The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
C64 zxAnLagIfOutFragments	1.3.6.1.4.1.3902.1082.30.31.2.4.1.36	Counter64	read-only	The total number of packets transmitted that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
C64 zxAnLagIfInJabbers	1.3.6.1.4.1.3902.1082.30.31.2.4.1.37	Counter64	read-only	The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). Note that this definition of jabber is different than the definition in IEEE-802.3 section 8.2.1.5 (10BASE5) and section 10.3.1.4 (10BASE2). These documents define jabber as the condition where any packet exceeds 20 ms. The allowed range to detect jabber is between 20 ms and 150 ms.
C64 zxAnLagIfOutJabbers	1.3.6.1.4.1.3902.1082.30.31.2.4.1.38	Counter64	read-only	The total number of packets transmitted that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). Note that this definition of jabber is different than the definition in IEEE-802.3 section 8.2.1.5 (10BASE5) and section 10.3.1.4 (10BASE2). These documents define jabber as the condition where any packet exceeds 20 ms. The allowed range to detect jabber is between 20 ms and 150 ms.
C64 zxAnLagIfOutPausePkts	1.3.6.1.4.1.3902.1082.30.31.2.4.1.39	Counter64	read-only	A count of MAC Control frames transmitted on this LAG interface with an opcode indicating the PAUSE operation. This counter does not increment when the LAG interface is operating in half-duplex mode. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCOutPauseFrames object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnLagIfOutCollisions	1.3.6.1.4.1.3902.1082.30.31.2.4.1.40	Counter64	read-only	A count of frames that are involved in out collision and are subsequently transmitted successfully. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnLagIfSingleCollisions	1.3.6.1.4.1.3902.1082.30.31.2.4.1.41	Counter64	read-only	A count of frames that are involved in a single collision, and are subsequently transmitted successfully. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsMultipleCollisionFrames object. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnLagIfMultipleCollisions	1.3.6.1.4.1.3902.1082.30.31.2.4.1.42	Counter64	read-only	A count of frames that are involved in more than one collision and are subsequently transmitted successfully. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnLagIfFcsErrors	1.3.6.1.4.1.3902.1082.30.31.2.4.1.43	Counter64	read-only	A count of frames received on a particular LAG interface that are an integral number of octets in length but do not pass the FCS check. This count does not include frames received with frame-too-long or frame-too-short error. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. Note: Coding errors detected by the physical layer for speeds above 10 Mb/s will cause the frame to fail the FCS check. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsFCSErrors object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnLagIfAlignmentErrors	1.3.6.1.4.1.3902.1082.30.31.2.4.1.44	Counter64	read-only	A count of frames received on a particular LAG interface that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. This counter does not increment for group encoding schemes greater than 4 bits per group. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsAlignmentErrors object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C32 zxAnLagIfLinkStatusChanges	1.3.6.1.4.1.3902.1082.30.31.2.4.1.45	Counter32	read-only	The total number of the link status changes on the LAG interface. The total number starts from zero and is increased when the link status changes from up to down, or from down to up.
INT zxAnLagIfReset	1.3.6.1.4.1.3902.1082.30.31.2.4.1.100	INTEGER	read-write	Clear all the statistics of LAG. When get this variable, always return 1.
zxAnIfRateStatsTable	1.3.6.1.4.1.3902.1082.30.31.2.20		not-accessible	The rate statistics table of interfaces.
zxAnIfRateStatsEntry	1.3.6.1.4.1.3902.1082.30.31.2.20.1		not-accessible	The rate statistics entry of interfaces.
I32 zxAnIfCurrTxNetDataRate	1.3.6.1.4.1.3902.1082.30.31.2.20.1.1	Integer32	read-only	Current actual transmitted net data rate of the interface.
I32 zxAnIfCurrRxNetDataRate	1.3.6.1.4.1.3902.1082.30.31.2.20.1.2	Integer32	read-only	Current actual received net data rate of the interface.
G32 zxAnIfCurrTxOctetRate	1.3.6.1.4.1.3902.1082.30.31.2.20.1.3	Gauge32	read-only	An estimate of the interface's current transmitted bandwidth in bytes per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnIfCurrRxOctetRate	1.3.6.1.4.1.3902.1082.30.31.2.20.1.4	Gauge32	read-only	An estimate of the interface's current received bandwidth in bytes per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnIfCurrTxPktRate	1.3.6.1.4.1.3902.1082.30.31.2.20.1.5	Gauge32	read-only	An estimate of the interface's current transmitted bandwidth in packets per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnIfCurrRxPktRate	1.3.6.1.4.1.3902.1082.30.31.2.20.1.6	Gauge32	read-only	An estimate of the interface's current received bandwidth in packets per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnIfCurrTxOctetPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.20.1.7	Gauge32	read-only	The interface's peak transmitted bandwidth in bytes per second. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnIfCurrRxOctetPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.20.1.8	Gauge32	read-only	The interface's peak received bandwidth in bytes per second. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnIfCurrTxErroredPktRate	1.3.6.1.4.1.3902.1082.30.31.2.20.1.9	Gauge32	read-only	Current transmitted errored packet rate.
G32 zxAnIfCurrRxErroredPktRate	1.3.6.1.4.1.3902.1082.30.31.2.20.1.10	Gauge32	read-only	Current received errored packet rate.
zxAnIfBandwidthUsingTable	1.3.6.1.4.1.3902.1082.30.31.2.30		not-accessible	Bandwidth using ratio and threshold table.
zxAnIfBandwidthUsingEntry	1.3.6.1.4.1.3902.1082.30.31.2.30.1		not-accessible	Bandwidth using entry.
I32 zxAnIfInBandwidthUsingRatio	1.3.6.1.4.1.3902.1082.30.31.2.30.1.1	Integer32	read-only	An estimate of the interface's current received bandwidth using ratio.
I32 zxAnIfOutBandwidthUsingRatio	1.3.6.1.4.1.3902.1082.30.31.2.30.1.2	Integer32	read-only	An estimate of the interface's current transmitted bandwidth using ratio.
I32 zxAnIfInBandwidthUsingThresh	1.3.6.1.4.1.3902.1082.30.31.2.30.1.3	Integer32	read-write	The threshold of zxAnIfInBandwidthUsingRatio. When zxAnIfInBandwidthUsingRatio exceeds this threshold, the zxAnIfInBwUsingThreshExceedAlm trap should be generated. If zxAnIfInBandwidthUsingRatio always exceeds the threshold, only one zxAnIfInBwUsingThreshExceedAlm trap should be sent.
I32 zxAnIfOutBandwidthUsingThresh	1.3.6.1.4.1.3902.1082.30.31.2.30.1.4	Integer32	read-write	The threshold of zxAnIfOutBandwidthUsingRatio. When zxAnIfOutBandwidthUsingRatio exceeds this threshold, the zxAnIfOutBwUsingThreshExceedAlm trap should be generated. If zxAnIfOutBandwidthUsingRatio always exceeds the threshold, only one zxAnIfOutBwUsingThreshExceedAlm trap should be sent.
I32 zxAnIfInBandwidthUsingRatioHa	1.3.6.1.4.1.3902.1082.30.31.2.30.1.5	Integer32	read-only	The high accuracy value of zxAnIfInBandwidthUsingRatio.
I32 zxAnIfOutBandwidthUsingRatioHa	1.3.6.1.4.1.3902.1082.30.31.2.30.1.6	Integer32	read-only	The high accuracy value of zxAnIfOutBandwidthUsingRatio
zxAnIfNumberStatsTable	1.3.6.1.4.1.3902.1082.30.31.2.40		not-accessible	The number of interfaces statistics table.
zxAnIfNumberStatsEntry	1.3.6.1.4.1.3902.1082.30.31.2.40.1		not-accessible	The number of interfaces statistics entry.
INT zxAnIfNumberStatsIfType	1.3.6.1.4.1.3902.1082.30.31.2.40.1.1	INTEGER	not-accessible	The interface type.
I32 zxAnIfNumberStatsTotalNumber	1.3.6.1.4.1.3902.1082.30.31.2.40.1.2	Integer32	read-only	The total number of interfaces.
I32 zxAnIfNumberStatsOnlineNumber	1.3.6.1.4.1.3902.1082.30.31.2.40.1.3	Integer32	read-only	The total number of online interfaces.
zxAnIfVlanCurrStatsTable	1.3.6.1.4.1.3902.1082.30.31.2.50		not-accessible	Interface VLAN statistic table.
zxAnIfVlanCurrStatsEntry	1.3.6.1.4.1.3902.1082.30.31.2.50.1		not-accessible	A zxAnIfVlanCurrStatsTable entry.
VLA zxAnIfVid	1.3.6.1.4.1.3902.1082.30.31.2.50.1.1	VlanId	not-accessible	The interface VLAN ID.
C64 zxAnIfVlanInPkts	1.3.6.1.4.1.3902.1082.30.31.2.50.1.2	Counter64	read-only	Received packets of the interface VLAN.
C64 zxAnIfVlanOutPkts	1.3.6.1.4.1.3902.1082.30.31.2.50.1.3	Counter64	read-only	Transmitted packets of the interface VLAN.
C64 zxAnIfVlanInOctets	1.3.6.1.4.1.3902.1082.30.31.2.50.1.4	Counter64	read-only	Received octets of the interface VLAN.
C64 zxAnIfVlanOutOctets	1.3.6.1.4.1.3902.1082.30.31.2.50.1.5	Counter64	read-only	Transmitted octets of the interface VLAN.
C64 zxAnIfVlanInUcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.50.1.6	Counter64	read-only	Received unicast packets of the interface VLAN.
C64 zxAnIfVlanOutUcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.50.1.7	Counter64	read-only	Transmitted unicast packets of the interface VLAN.
C64 zxAnIfVlanInUcastOctets	1.3.6.1.4.1.3902.1082.30.31.2.50.1.8	Counter64	read-only	Received unicast octets of the interface VLAN.
C64 zxAnIfVlanOutUcastOctets	1.3.6.1.4.1.3902.1082.30.31.2.50.1.9	Counter64	read-only	Transmitted unicast octets of the interface VLAN.
C64 zxAnIfVlanInMcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.50.1.10	Counter64	read-only	Received multicast packets of the interface VLAN.
C64 zxAnIfVlanOutMcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.50.1.11	Counter64	read-only	Transmitted multicast packets of the interface VLAN.
C64 zxAnIfVlanInMcastOctets	1.3.6.1.4.1.3902.1082.30.31.2.50.1.12	Counter64	read-only	Received multicast octets of the interface VLAN.
C64 zxAnIfVlanOutMcastOctets	1.3.6.1.4.1.3902.1082.30.31.2.50.1.13	Counter64	read-only	Transmitted multicast octets of the interface VLAN.
C64 zxAnIfVlanInBcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.50.1.14	Counter64	read-only	Received broadcast packets of the interface VLAN.
C64 zxAnIfVlanOutBcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.50.1.15	Counter64	read-only	Transmitted broadcast packets of the interface VLAN.
C64 zxAnIfVlanInBcastOctets	1.3.6.1.4.1.3902.1082.30.31.2.50.1.16	Counter64	read-only	Received broadcast octets of the interface VLAN.
C64 zxAnIfVlanOutBcastOctets	1.3.6.1.4.1.3902.1082.30.31.2.50.1.17	Counter64	read-only	Transmitted broadcast octets of the interface VLAN.
C64 zxAnIfVlanInFloodPkts	1.3.6.1.4.1.3902.1082.30.31.2.50.1.18	Counter64	read-only	Received flooding packets of the interface VLAN.
C64 zxAnIfVlanOutFloodPkts	1.3.6.1.4.1.3902.1082.30.31.2.50.1.19	Counter64	read-only	Transmitted flooding packets of the interface VLAN.
C64 zxAnIfVlanInFloodOctets	1.3.6.1.4.1.3902.1082.30.31.2.50.1.20	Counter64	read-only	Received flooding octets of the interface VLAN.
C64 zxAnIfVlanOutFloodOctets	1.3.6.1.4.1.3902.1082.30.31.2.50.1.21	Counter64	read-only	Transmitted flooding octets of the interface VLAN.
C64 zxAnIfVlanInDiscardPkts	1.3.6.1.4.1.3902.1082.30.31.2.50.1.22	Counter64	read-only	Received discarded packets of the interface VLAN.
C64 zxAnIfVlanOutDiscardPkts	1.3.6.1.4.1.3902.1082.30.31.2.50.1.23	Counter64	read-only	Transmitted discarded packets of the interface VLAN.
C64 zxAnIfVlanInDiscardOctets	1.3.6.1.4.1.3902.1082.30.31.2.50.1.24	Counter64	read-only	Received discarded octets of the interface VLAN.
C64 zxAnIfVlanOutDiscardOctets	1.3.6.1.4.1.3902.1082.30.31.2.50.1.25	Counter64	read-only	Transmitted discarded octets of the interface VLAN.
C64 zxAnIfVlanInErrorPkts	1.3.6.1.4.1.3902.1082.30.31.2.50.1.26	Counter64	read-only	Received errored packets of the interface VLAN.
C64 zxAnIfVlanOutErrorPkts	1.3.6.1.4.1.3902.1082.30.31.2.50.1.27	Counter64	read-only	Transmitted errored packets of the interface VLAN.
C64 zxAnIfVlanInErrorOctets	1.3.6.1.4.1.3902.1082.30.31.2.50.1.28	Counter64	read-only	Received errored octets of the interface VLAN.
C64 zxAnIfVlanOutErrorOctets	1.3.6.1.4.1.3902.1082.30.31.2.50.1.29	Counter64	read-only	Transmitted errored octets of the interface VLAN.
INT zxAnIfVlanCurrStatsReset	1.3.6.1.4.1.3902.1082.30.31.2.50.1.99	INTEGER	read-create	Clear all the current performance variables. When get this variable, always return 1. Reset port vlan statistics counter manually when it is set to '1'.
ROW zxAnIfVlanCurrStatsRowStatus	1.3.6.1.4.1.3902.1082.30.31.2.50.1.100	RowStatus	read-create	The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnIfVlanCurrStatsEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
zxAnIfVlanRateStatsTable	1.3.6.1.4.1.3902.1082.30.31.2.51		not-accessible	Interface VLAN rate statistic table.
zxAnIfVlanRateStatsEntry	1.3.6.1.4.1.3902.1082.30.31.2.51.1		not-accessible	A zxAnIfVlanRateStatsTable entry.
G32 zxAnIfVlanRxPktRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.1	Gauge32	read-only	Received packet rate of the interface VLAN.
G32 zxAnIfVlanTxPktRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.2	Gauge32	read-only	Transmitted packet rate of the interface VLAN.
G32 zxAnIfVlanRxPktPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.3	Gauge32	read-only	Received pakcet peak rate of the interface VLAN.
G32 zxAnIfVlanTxPktPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.4	Gauge32	read-only	Transmitted packet peak rate of the interface VLAN.
G32 zxAnIfVlanRxUcastPktRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.5	Gauge32	read-only	Received unicast packet rate of the interface VLAN.
G32 zxAnIfVlanTxUcastPktRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.6	Gauge32	read-only	Transmitted unicast packet rate of the interface VLAN.
G32 zxAnIfVlanRxUcastPktPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.7	Gauge32	read-only	Transmitted unicast packet peak rate of the interface VLAN.
G32 zxAnIfVlanTxUcastPktPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.8	Gauge32	read-only	Transmitted unicast packet peak rate of the interface VLAN.
G32 zxAnIfVlanRxMcastPktRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.9	Gauge32	read-only	Received multicast packet rate of the interface VLAN.
G32 zxAnIfVlanTxMcastPktRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.10	Gauge32	read-only	Transmitted multicast packet rate of the interface VLAN.
G32 zxAnIfVlanRxMcastPktPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.11	Gauge32	read-only	Received multicast packet peak rate of the interface VLAN.
G32 zxAnIfVlanTxMcastPktPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.12	Gauge32	read-only	Transmitted multicast packet peak rate of the interface VLAN.
G32 zxAnIfVlanRxBcastPktRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.13	Gauge32	read-only	Received broadcast packet rate of the interface VLAN.
G32 zxAnIfVlanTxBcastPktRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.14	Gauge32	read-only	Received broadcast packet rate of the interface VLAN.
G32 zxAnIfVlanRxBcastPktPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.15	Gauge32	read-only	Received broadcast packet peak rate of the interface VLAN.
G32 zxAnIfVlanTxBcastPktPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.16	Gauge32	read-only	Transmitted broadcast packet peak rate of the interface VLAN.
G32 zxAnIfVlanRxFloodPktRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.17	Gauge32	read-only	Received flooding packet rate of the interface VLAN.
G32 zxAnIfVlanTxFloodPktRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.18	Gauge32	read-only	Transmitted flooding packet rate of the interface VLAN.
G32 zxAnIfVlanRxFloodPktPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.19	Gauge32	read-only	Received flooding packet peak rate of the interface VLAN.
G32 zxAnIfVlanTxFloodPktPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.20	Gauge32	read-only	Transmitted flooding packet peak rate of the interface VLAN.
G32 zxAnIfVlanRxDiscardPktRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.21	Gauge32	read-only	Received discarded packet rate of the interface VLAN.
G32 zxAnIfVlanTxDiscardPktRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.22	Gauge32	read-only	Transmitted discarded packet rate of the interface VLAN.
G32 zxAnIfVlanRxDiscardPktPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.23	Gauge32	read-only	Received discarded packet peak rate of the interface VLAN.
G32 zxAnIfVlanTxDiscardPktPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.24	Gauge32	read-only	Transmitted discarded packet peak rate of the interface VLAN.
G32 zxAnIfVlanRxErrorPktRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.25	Gauge32	read-only	Received errored packet rate of the interface VLAN.
G32 zxAnIfVlanTxErrorPktRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.26	Gauge32	read-only	Transmitted errored packet rate of the interface VLAN.
G32 zxAnIfVlanRxErrorPktPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.27	Gauge32	read-only	Received errored packet peak rate of the interface VLAN.
G32 zxAnIfVlanTxErrorPktPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.51.1.28	Gauge32	read-only	Transmitted errored packet peak rate of the interface VLAN.
zxAnIfVlan2CurrStatsTable	1.3.6.1.4.1.3902.1082.30.31.2.52		not-accessible	Interface S-VID and C-VID statistic table.
zxAnIfVlan2CurrStatsEntry	1.3.6.1.4.1.3902.1082.30.31.2.52.1		not-accessible	Interface SVLAN and CVLAN statistic entry.
VLA zxAnIfVlan2CurrStatsSVid	1.3.6.1.4.1.3902.1082.30.31.2.52.1.1	VlanId	not-accessible	The interface S-VID.
I32 zxAnIfVlan2CurrStatsCVid	1.3.6.1.4.1.3902.1082.30.31.2.52.1.2	Integer32	not-accessible	The interface C-VID. Value 0 means statistics only based on S-VID.
C64 zxAnIfVlan2InPkts	1.3.6.1.4.1.3902.1082.30.31.2.52.1.3	Counter64	read-only	Received packets of the interface VLAN.
C64 zxAnIfVlan2OutPkts	1.3.6.1.4.1.3902.1082.30.31.2.52.1.4	Counter64	read-only	Transmitted packets of the interface VLAN.
C64 zxAnIfVlan2InOctets	1.3.6.1.4.1.3902.1082.30.31.2.52.1.5	Counter64	read-only	Received octets of the interface VLAN.
C64 zxAnIfVlan2OutOctets	1.3.6.1.4.1.3902.1082.30.31.2.52.1.6	Counter64	read-only	Transmitted octets of the interface VLAN.
INT zxAnIfVlan2CurrStatsReset	1.3.6.1.4.1.3902.1082.30.31.2.52.1.100	INTEGER	read-create	Clear all the current performance variables. When get this variable, always return 1. Reset port vlan statistics counter manually when it is set to '1'.
zxAnBrgIfCurrPerfStatsTable	1.3.6.1.4.1.3902.1082.30.31.2.60		not-accessible	Enable/disable the bridge interface current performance statistics.
zxAnBrgIfCurrPerfStatsEntry	1.3.6.1.4.1.3902.1082.30.31.2.60.1		not-accessible	A zxAnBrgIfCurrPerfStatsTable entry.
ROW zxAnBrgIfCurrPerfStatsRowStatus	1.3.6.1.4.1.3902.1082.30.31.2.60.1.100	RowStatus	read-create	The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnBrgIfCurrPerfStatsEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
zxAnIfVlanCurrPerfStatsTable	1.3.6.1.4.1.3902.1082.30.31.2.61		not-accessible	Enable/disable the interface S-VID and C-VID current performance statistics.
zxAnIfVlanCurrPerfStatsEntry	1.3.6.1.4.1.3902.1082.30.31.2.61.1		not-accessible	A zxAnIfVlanCurrPerfStatsTable entry.
VLA zxAnIfVlanPerfStatsSVid	1.3.6.1.4.1.3902.1082.30.31.2.61.1.1	VlanId	not-accessible	The interface S-VID.
I32 zxAnIfVlanPerfStatsCVid	1.3.6.1.4.1.3902.1082.30.31.2.61.1.2	Integer32	not-accessible	The interface C-VID. Value 0 means statistics only based on S-VID.
ROW zxAnIfVlanPerfStatsRowStatus	1.3.6.1.4.1.3902.1082.30.31.2.61.1.100	RowStatus	read-create	The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnIfVlanCurrPerfStatsEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
zxAnVnd0EthIfCurrStatsTable	1.3.6.1.4.1.3902.1082.30.31.2.62		not-accessible	Current performance data table of shared interfaces of the VND 0.
zxAnVnd0EthIfCurrStatsEntry	1.3.6.1.4.1.3902.1082.30.31.2.62.1		not-accessible	Current performance data entry of shared interfaces of the VND 0.
C64 zxAnVnd0EthIfInOctets	1.3.6.1.4.1.3902.1082.30.31.2.62.1.1	Counter64	read-only	The total number of octets received on the shared interface of the VND 0, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnVnd0EthIfOutOctets	1.3.6.1.4.1.3902.1082.30.31.2.62.1.2	Counter64	read-only	The total number of octets transmitted out on the shared interface of the VND 0, including framing characters.
C64 zxAnVnd0EthIfInPkts	1.3.6.1.4.1.3902.1082.30.31.2.62.1.3	Counter64	read-only	The total number of packets received on the shared interface of the VND 0, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnVnd0EthIfOutPkts	1.3.6.1.4.1.3902.1082.30.31.2.62.1.4	Counter64	read-only	The total number of packets transmitted out on the shared interface of the VND 0, including framing characters.
C64 zxAnVnd0EthIfInUcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.62.1.5	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnVnd0EthIfOutUcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.62.1.6	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnVnd0EthIfInMcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.62.1.7	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnVnd0EthIfOutMcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.62.1.8	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime
C64 zxAnVnd0EthIfInBcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.62.1.9	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnVnd0EthIfOutBcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.62.1.10	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
G32 zxAnVnd0EthIfRxOctetRate	1.3.6.1.4.1.3902.1082.30.31.2.62.1.11	Gauge32	read-only	An estimate of the received bandwidth in bytes per second on the shared interface of the VND 0. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnVnd0EthIfTxOctetRate	1.3.6.1.4.1.3902.1082.30.31.2.62.1.12	Gauge32	read-only	An estimate of the transmitted bandwidth in bytes per second on the shared interface of the VND 0. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnVnd0EthIfRxPktRate	1.3.6.1.4.1.3902.1082.30.31.2.62.1.13	Gauge32	read-only	An estimate of the received bandwidth in packets per second on the shared interface of the VND 0. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnVnd0EthIfTxPktRate	1.3.6.1.4.1.3902.1082.30.31.2.62.1.14	Gauge32	read-only	An estimate of the transmitted bandwidth in packets per second on the shared interface of the VND 0. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnVnd0EthIfRxOctetPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.62.1.15	Gauge32	read-only	The peak received bandwidth in bytes per second on the shared interface of the VND 0. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnVnd0EthIfTxOctetPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.62.1.16	Gauge32	read-only	The peak transmitted bandwidth in bytes per second on the shared interface of the VND 0. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
I32 zxAnVnd0EthIfInBwUsingRatio	1.3.6.1.4.1.3902.1082.30.31.2.62.1.17	Integer32	read-only	An estimate of the received bandwidth using ratio on the shared interface of the VND 0.
I32 zxAnVnd0EthIfOutBwUsingRatio	1.3.6.1.4.1.3902.1082.30.31.2.62.1.18	Integer32	read-only	An estimate of the transmitted bandwidth using ratio on the shared interface of the VND 0.
I32 zxAnVnd0EthIfInBwUsingRatioHa	1.3.6.1.4.1.3902.1082.30.31.2.62.1.19	Integer32	read-only	The high accuracy value of zxAnVnd0EthIfInBwUsingRatio.
I32 zxAnVnd0EthIfOutBwUsingRatioHa	1.3.6.1.4.1.3902.1082.30.31.2.62.1.20	Integer32	read-only	The high accuracy value of zxAnVnd0EthIfOutBwUsingRatio
C32 zxAnVnd0EthIfLinkStatusChanges	1.3.6.1.4.1.3902.1082.30.31.2.62.1.51	Counter32	read-only	The total number of the link status changes on the shared interface of the VND 0. The total number starts from zero and is increased when the link status changes from up to down, or from down to up.
INT zxAnVnd0EthIfReset	1.3.6.1.4.1.3902.1082.30.31.2.62.1.100	INTEGER	read-write	Clear all the current performance variables. When get this variable, always return 1.
zxAnVnd0LagIfCurrStatsTable	1.3.6.1.4.1.3902.1082.30.31.2.64		not-accessible	Current performance data table of shared LAG interfaces of the VND 0.
zxAnVnd0LagIfCurrStatsEntry	1.3.6.1.4.1.3902.1082.30.31.2.64.1		not-accessible	Current performance data entry of shared LAG interfaces of the VND 0.
C64 zxAnVnd0LagIfInOctets	1.3.6.1.4.1.3902.1082.30.31.2.64.1.1	Counter64	read-only	The total number of octets received on the shared LAG interface of the VND 0, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnVnd0LagIfOutOctets	1.3.6.1.4.1.3902.1082.30.31.2.64.1.2	Counter64	read-only	The total number of octets transmitted out on the shared LAG interface of the VND 0, including framing characters.
C64 zxAnVnd0LagIfInPkts	1.3.6.1.4.1.3902.1082.30.31.2.64.1.3	Counter64	read-only	The total number of packets received on the shared LAG interface of the VND 0, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnVnd0LagIfOutPkts	1.3.6.1.4.1.3902.1082.30.31.2.64.1.4	Counter64	read-only	The total number of packets transmitted out on the shared LAG interface of the VND 0, including framing characters.
C64 zxAnVnd0LagIfInUcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.64.1.5	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnVnd0LagIfOutUcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.64.1.6	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnVnd0LagIfInMcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.64.1.7	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnVnd0LagIfOutMcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.64.1.8	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime
C64 zxAnVnd0LagIfInBcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.64.1.9	Counter64	read-only	The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
C64 zxAnVnd0LagIfOutBcastPkts	1.3.6.1.4.1.3902.1082.30.31.2.64.1.10	Counter64	read-only	The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
G32 zxAnVnd0LagIfRxOctetRate	1.3.6.1.4.1.3902.1082.30.31.2.64.1.11	Gauge32	read-only	An estimate of the received bandwidth in bytes per second on the shared LAG interface of the VND 0. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnVnd0LagIfTxOctetRate	1.3.6.1.4.1.3902.1082.30.31.2.64.1.12	Gauge32	read-only	An estimate of the transmitted bandwidth in bytes per second on the shared LAG interface of the VND 0. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnVnd0LagIfRxPktRate	1.3.6.1.4.1.3902.1082.30.31.2.64.1.13	Gauge32	read-only	An estimate of the received bandwidth in packets per second on the shared LAG interface of the VND 0. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnVnd0LagIfTxPktRate	1.3.6.1.4.1.3902.1082.30.31.2.64.1.14	Gauge32	read-only	An estimate of the transmitted bandwidth in packets per second on the shared LAG interface of the VND 0. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnVnd0LagIfRxOctetPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.64.1.15	Gauge32	read-only	The peak received bandwidth in bytes per second on the shared LAG interface of the VND 0. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
G32 zxAnVnd0LagIfTxOctetPeakRate	1.3.6.1.4.1.3902.1082.30.31.2.64.1.16	Gauge32	read-only	The peak transmitted bandwidth in bytes per second on the shared LAG interface of the VND 0. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295).
I32 zxAnVnd0LagIfInBwUsingRatio	1.3.6.1.4.1.3902.1082.30.31.2.64.1.17	Integer32	read-only	An estimate of the received bandwidth using ratio on the shared LAG interface of the VND 0.
I32 zxAnVnd0LagIfOutBwUsingRatio	1.3.6.1.4.1.3902.1082.30.31.2.64.1.18	Integer32	read-only	An estimate of the transmitted bandwidth using ratio on the shared LAG interface of the VND 0.
I32 zxAnVnd0LagIfInBwUsingRatioHa	1.3.6.1.4.1.3902.1082.30.31.2.64.1.19	Integer32	read-only	The high accuracy value of zxAnVnd0LagIfInBwUsingRatio.
I32 zxAnVnd0LagIfOutBwUsingRatioHa	1.3.6.1.4.1.3902.1082.30.31.2.64.1.20	Integer32	read-only	The high accuracy value of zxAnVnd0LagIfOutBwUsingRatio
C32 zxAnVnd0LagIfLinkStatusChanges	1.3.6.1.4.1.3902.1082.30.31.2.64.1.51	Counter32	read-only	The total number of the link status changes on the shared LAG interface of the VND 0. The total number starts from zero and is increased when the link status changes from up to down, or from down to up.
INT zxAnVnd0LagIfReset	1.3.6.1.4.1.3902.1082.30.31.2.64.1.100	INTEGER	read-write	Clear all the current performance variables. When get this variable, always return 1.
zxAnIfPerfNotifications	1.3.6.1.4.1.3902.1082.30.31.3
zxAnIfBwUsingTraps	1.3.6.1.4.1.3902.1082.30.31.3.1
NTF zxAnIfInBwUsingThreshExceedAlm	1.3.6.1.4.1.3902.1082.30.31.3.1.1			It indicates that zxAnIfInBandwidthUsingRatio exceeds the threshold zxAnIfInBandwidthUsingThresh.
NTF zxAnIfInBwUsingThreshExceedClr	1.3.6.1.4.1.3902.1082.30.31.3.1.2			It indicates that zxAnIfInBandwidthUsingRatio is below the threshold zxAnIfInBandwidthUsingThresh.
NTF zxAnIfOutBwUsingThreshExceedAlm	1.3.6.1.4.1.3902.1082.30.31.3.1.3			It indicates that zxAnIfOutBandwidthUsingRatio exceeds the threshold zxAnIfOutBandwidthUsingThresh.
NTF zxAnIfOutBwUsingThreshExceedClr	1.3.6.1.4.1.3902.1082.30.31.3.1.4			It indicates that zxAnIfOutBandwidthUsingRatio is below the threshold zxAnIfOutBandwidthUsingThresh.
zxAnIfPerfConformance	1.3.6.1.4.1.3902.1082.30.31.4
zxAnIfPerfCompliances	1.3.6.1.4.1.3902.1082.30.31.4.1
zxAnIfeEthPerfCompliance	1.3.6.1.4.1.3902.1082.30.31.4.1.1			The compliance statement for entities which implement the ZTE-AN-INTERFACE-PERF-MIB.
zxAnIfBrgPerfCompliance	1.3.6.1.4.1.3902.1082.30.31.4.1.2			The compliance statement for entities which implement the ZTE-AN-INTERFACE-PERF-MIB.
zxAnIfPerfGroups	1.3.6.1.4.1.3902.1082.30.31.4.2
zxAnEthIfPerfCurrGroup	1.3.6.1.4.1.3902.1082.30.31.4.2.1			A collection of objects providing current performance data of interfaces.
zxAnBrgIfPerfCurrGroup	1.3.6.1.4.1.3902.1082.30.31.4.2.2			A collection of objects providing current performance data of interfaces.

RFC description

Monitors interface performance metrics and statistics on ZTE Access Node equipment.

Start monitoring ZTE Access Node (AN) broadband access / DSLAM-class equipment (Ethernet/bridge/LAG/VLAN traffic-statistics status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ZTE-AN-INTERFACE-STATS-MIB