ZTE-AN-PPPOE-TEST-MIB

All MIBs › ZTE-AN-PPPOE-TEST-MIB

Organization: ZTE Corporation

Last Updated: 2014-10-20

Category: ZTE Access Node (ZTE-AN) Management

Description: Provides ZTE access node PPPoE diagnostic test operations for subscriber connectivity troubleshooting.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ZTE-AN-PPPOE-TEST-MIB?

ZTE-AN-PPPOE-TEST-MIB is part of ZTE's Access Node diagnostic toolkit and provides objects to trigger and read back PPPoE session-establishment tests against a subscriber line. It exposes test-invocation and result objects rather than ongoing operational counters. It is a software-level diagnostic MIB: it verifies whether the access node's PPPoE relay/proxy path and the upstream PPPoE server (typically a BRAS) can complete session negotiation for a given port, isolating faults without needing a technician on site. It implicitly depends on the PPPoE protocol standard (RFC 2516). It is typically deployed by broadband access operators for remote troubleshooting of subscriber PPPoE connectivity issues. Engineers can download the ZTE-AN-PPPOE-TEST-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ZTE-AN-PPPOE-TEST-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ZTE access node (DSLAM/OLT broadband access platform)

Monitoring Examples

No specific object names were present in the source for this module, so the following is inferred from module_desc: an operator would trigger a PPPoE test on a given subscriber port and poll a test-result/status object to determine whether the PADI/PADO/session negotiation succeeded. A failed result would let the operator distinguish a local access-node fault from an upstream BRAS or PPPoE server issue.

What Can Be Monitored

PPPoE test invocation on a subscriber port
PPPoE test result/status
test target port identification

Imported Objects

From IF-MIB

ifIndex

OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressPrefixLength
InetAddressType

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE
enterprises

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
TEXTUAL-CONVENTION

From ZTE-AN-IF-MIB

zxAnSubIfIndex

OBJECT-TYPE

From ZTE-AN-SMI

zxAnServiceSecurity

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
zxAnPppoeTestMib	1.3.6.1.4.1.3902.1082.70.56			The MIB module for the management of PPPoE test.
zxAnPppoeTestGlobalObjects	1.3.6.1.4.1.3902.1082.70.56.1
BIT zxAnPppoeTestCapabilities	1.3.6.1.4.1.3902.1082.70.56.1.1	Bits	read-only	The PPPoE test compatibility. The bit value 1 means the function represented by this bit is supported by this equipment. bit 0: value 1 means not supporting zxAnPppoeTestIfUserVid in zxAnPppoeTestIfConfTable. bit 1: value 1 means supporting zxAnPppoeTestIfUserMacAddress in zxAnPppoeTestIfConfTable. NOTE: No recommended to display it in NMS.
zxAnPppoeTestObjects	1.3.6.1.4.1.3902.1082.70.56.2
zxAnPppoeTestIfConfTable	1.3.6.1.4.1.3902.1082.70.56.2.2		not-accessible	PPPoE test interface configuration table.
zxAnPppoeTestIfConfEntry	1.3.6.1.4.1.3902.1082.70.56.2.2.1		not-accessible	A zxAnPppoeTestIfConfTable entry.
I32 zxAnPppoeTestIfUserVid	1.3.6.1.4.1.3902.1082.70.56.2.2.1.1	Integer32	read-create	The user VLAN of the interface which will be used in the testing datagram. 0 means that test will use the PVID of interface. Non-zero value must be within the tagged VLAN list of interface. If the VLAN cannot be found in the tagged VLAN list of interface, test should fail.
STR zxAnPppoeTestIfPppUserName	1.3.6.1.4.1.3902.1082.70.56.2.2.1.2	DisplayString	read-create	User name for PPP authentication.
STR zxAnPppoeTestIfPppPassword	1.3.6.1.4.1.3902.1082.70.56.2.2.1.3	DisplayString	read-create	Password for PPP authentication.
INT zxAnPppoeTestIfAuthMode	1.3.6.1.4.1.3902.1082.70.56.2.2.1.4	INTEGER	read-create	The protocol for user authentication. Possible values are: auto(1) - Assigned automatically. pap(2) - Performing PAP authentication in PPPoE test. chap(3) - Performing CHAP authentication in PPPoE test.
I32 zxAnPppoeTestIfTimeout	1.3.6.1.4.1.3902.1082.70.56.2.2.1.5	Integer32	read-create	The PPPoE test timeout value, in seconds. Value 0 means no timeout.
MAC zxAnPppoeTestIfUserMacAddress	1.3.6.1.4.1.3902.1082.70.56.2.2.1.6	MacAddress	read-create	The PPPoE test user MAC address.
ROW zxAnIfPppoeTestIfRowStatus	1.3.6.1.4.1.3902.1082.70.56.2.2.1.50	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table. Only 'createAndGo' and 'destroy' need to be supported. If test is in progress, agent should reject the 'destroy' request from manager. 'createAndGo' means creating an entry. 'destroy' means deleting an entry.
zxAnPppoeTestIfStatusTable	1.3.6.1.4.1.3902.1082.70.56.2.3		not-accessible	PPPoE test interface status table.
zxAnPppoeTestIfStatusEntry	1.3.6.1.4.1.3902.1082.70.56.2.3.1		not-accessible	A zxAnPppoeTestIfStatusTable entry.
INT zxAnPppoeTestIfStatus	1.3.6.1.4.1.3902.1082.70.56.2.3.1.1	INTEGER	read-only	PPPoE test status. Agent need keep this parameter updated so that manager can get the latest status of test by polling. Possible values are: notStarted(1) - PPPoE test is not started. inProgress(2) - PPPoE test is in progress. success(3) - PPPoE test is completed successfully. failed(4) - PPPoE test failed.
INT zxAnPppoeTestIfFailReason	1.3.6.1.4.1.3902.1082.70.56.2.3.1.2	INTEGER	read-only	Failed reason for PPPoE test. Possible values are: none(1) - No Error unknownError(2) - Unknown Error hardwareNotSupport(3) - Hardware Not Supported vlanNotFound(4) - VLAN Not Found padiTimeout(5) - PADI Request Timeout padrTimeout(6) - PADR Request Timeout lcpNegotiationFail(7) - LCP Negotiation Failed userAuthFail(8) - Incorrect User Name or Password ipNegotiationFail(9) - IP Negotiation Failed pppoeTestTimeout(10) - PPPoE Test Timeout
MAC zxAnPppoeTestIfBasMac	1.3.6.1.4.1.3902.1082.70.56.2.3.1.3	MacAddress	read-only	MAC address of BAS.
IPt zxAnPppoeTestIfRemotePeerIpType	1.3.6.1.4.1.3902.1082.70.56.2.3.1.4	InetAddressType	read-only	IP address type of the remote peer.
IP zxAnPppoeTestIfRemotePeerIpAddr	1.3.6.1.4.1.3902.1082.70.56.2.3.1.5	InetAddress	read-only	IP address of the remote peer.
IPt zxAnPppoeTestIfClientIpType	1.3.6.1.4.1.3902.1082.70.56.2.3.1.6	InetAddressType	read-only	Client IP address type.
IP zxAnPppoeTestIfClientIpAddr	1.3.6.1.4.1.3902.1082.70.56.2.3.1.7	InetAddress	read-only	The IP address that is distributed by BAS.
I32 zxAnPppoeTestIfPppoeSessionId	1.3.6.1.4.1.3902.1082.70.56.2.3.1.8	Integer32	read-only	PPPoE session ID.
I32 zxAnPppoeTestIfBasDelay	1.3.6.1.4.1.3902.1082.70.56.2.3.1.9	Integer32	read-only	BAS delay. Value 0 means that the device is disconnected to BAS.

RFC description

Provides ZTE access node PPPoE diagnostic test operations for subscriber connectivity troubleshooting; vendor-private.

Start monitoring ZTE access node (DSLAM/OLT broadband access platform) (PPPoE session-establishment diagnostic test-result status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ZTE-AN-PPPOE-TEST-MIB

What Is ZTE-AN-PPPOE-TEST-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description