ZTE-AN-INTERFACE-STATS-MIB :: zxAnEthIfOutPausePkts

MIB Reference — IPNetwork Monitor · Updated October 06, 2026

All MIBs › ZTE-AN-INTERFACE-STATS-MIB › zxAnEthIfOutPausePkts

zxAnEthIfOutPausePkts

Module: ZTE-AN-INTERFACE-STATS-MIB

OID (symbolic): ZTE-AN-INTERFACE-STATS-MIB::zxAnEthIfOutPausePkts

OID (numeric): 1.3.6.1.4.1.3902.1082.30.31.2.2.1.13

Node type: OBJECT-TYPE

Type: Counter64

Access: read-only

Description: A count of MAC Control frames transmitted on this interface with an opcode indicating the PAUSE operation.

This counter does not increment when the interface is operating in half-duplex mode.

For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCOutPauseFrames object for 10 Gb/s or faster interfaces.

Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.

What is zxAnEthIfOutPausePkts?

A count of 802.3x PAUSE flow-control frames transmitted on this Ethernet port; since it only increments in full-duplex mode, a climbing count on a supposedly idle link can indicate the switch is asking the far end to slow down due to buffer pressure.

Examples

Walk all instances (SNMPv2c):

snmpwalk -v2c -c public <target> 1.3.6.1.4.1.3902.1082.30.31.2.2.1.13
snmpwalk -v2c -c public <target> ZTE-AN-INTERFACE-STATS-MIB::zxAnEthIfOutPausePkts

Get a specific instance (index 1):

snmpget -v2c -c public <target> 1.3.6.1.4.1.3902.1082.30.31.2.2.1.13.1
snmpget -v2c -c public <target> ZTE-AN-INTERFACE-STATS-MIB::zxAnEthIfOutPausePkts.1

Start monitoring ZTE Access Node (AN) broadband access / DSLAM-class equipment (Ethernet/bridge/LAG/VLAN traffic-statistics status) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the ZTE-AN-INTERFACE-STATS-MIB::zxAnEthIfOutPausePkts OID value, configure state conditions and alerts, and monitor any ZTE Access Node (AN) broadband access / DSLAM-class equipment (Ethernet/bridge/LAG/VLAN traffic-statistics status) from a single console.

OID Breakdown

Upper-level ancestors (9 from the standard OID tree / other modules)
Numeric OIDNameModule
1isoLANART-AGENT
1.3orgAirPair-MIB
1.3.6dodAirPair-MIB
1.3.6.1internetAirPair-MIB
1.3.6.1.4privateAirPair-MIB
1.3.6.1.4.1enterprisesAirPair-MIB
1.3.6.1.4.1.3902zteDPI-MIB
1.3.6.1.4.1.3902.1082zxAccessNodeZTE-AN-SMI
1.3.6.1.4.1.3902.1082.30zxAnInterfaceZTE-AN-SMI
Numeric OIDNameModule
1.3.6.1.4.1.3902.1082.30.31zxAnInterfaceStatsMibZTE-AN-INTERFACE-STATS-MIB
1.3.6.1.4.1.3902.1082.30.31.2zxAnIfPerfObjectsZTE-AN-INTERFACE-STATS-MIB
1.3.6.1.4.1.3902.1082.30.31.2.2zxAnEthIfCurrStatsTableZTE-AN-INTERFACE-STATS-MIB
1.3.6.1.4.1.3902.1082.30.31.2.2.1zxAnEthIfCurrStatsEntryZTE-AN-INTERFACE-STATS-MIB
1.3.6.1.4.1.3902.1082.30.31.2.2.1.13zxAnEthIfOutPausePktsZTE-AN-INTERFACE-STATS-MIB