| OID symbolic | OID numeric | Type | Access | Description |
|---|
| timetraOesMIBModule | 1.3.6.1.4.1.6527.1.1.3.98 | | | This document is the SNMP MIB module to manage and provision the
Optical Extension Shelf (OES) components of the Nokia SROS
device.
Copyright (c) 2013-2016 Nokia. All rights reserved.
Reproduction of this document is authorized on the condition that
the foregoing copyright notice is included.
This SNMP MIB module (Specification) embodies Nokia's
proprietary intellectual property. Nokia retains
all title and ownership in the Specification, including any
revisions.
Nokia grants all interested parties a non-exclusive
license to use and distribute an unmodified copy of this
Specification in connection with management of Nokia
products, and without fee, provided this copyright notice and
license appear on all copies.
This Specification is supplied 'as is', and Nokia
makes no warranty, either express or implied, as to the use,
operation, condition, or performance of the Specification. |
| tmnxOesConformance | 1.3.6.1.4.1.6527.3.1.1.98 | | | |
| tmnxOesCompliances | 1.3.6.1.4.1.6527.3.1.1.98.1 | | | |
| tmnxOesV14v0Compliance | 1.3.6.1.4.1.6527.3.1.1.98.1.1 | | | The compliance statement for management of OES
on Nokia SROS series systems for release 14.0. |
| tmnxOesGroups | 1.3.6.1.4.1.6527.3.1.1.98.2 | | | |
| tmnxOesV14v0Groups | 1.3.6.1.4.1.6527.3.1.1.98.2.1 | | | |
| tmnxOesGroupV14v0 | 1.3.6.1.4.1.6527.3.1.1.98.2.1.1 | | | The group of objects supporting management of OES on
Nokia SROS series systems in release 14.0. |
| tmnxOesNotificationGroupV14v0 | 1.3.6.1.4.1.6527.3.1.1.98.2.1.2 | | | The group of notifications supporting management of OES on
Nokia SROS series systems in release 14.0. |
| tmnxOesNotifyObjsGroupV14v0 | 1.3.6.1.4.1.6527.3.1.1.98.2.1.3 | | | The group of notification objects supporting management of OES on
Nokia SROS series systems in release 14.0. |
| tmnxOesObjs | 1.3.6.1.4.1.6527.3.1.2.98 | | | |
| tmnxOesConfigObjs | 1.3.6.1.4.1.6527.3.1.2.98.1 | | | |
| INT tmnxOesCfCache | 1.3.6.1.4.1.6527.3.1.2.98.1.1 | INTEGER | read-write | The value of tmnxOesCfCache specifies the compact flash device
that holds the cache space used by OES. This cache space holds
OES artifacts (e.g. configuration database, software). |
| INT tmnxOesReboot | 1.3.6.1.4.1.6527.3.1.2.98.1.2 | INTEGER | read-write | The value of tmnxOesReboot specifies if the OES system will perform
a reboot :
notApplicable (0) - No action will be performed.
coldReset (1) - Causes a cold reset of the OES system in which
the hardware and software will be reinitialized on all EC(Equipment
Controller) and line cards. It is a service affecting action. |
| TMN tmnxOesSwUpgrade | 1.3.6.1.4.1.6527.3.1.2.98.1.3 | TmnxActionType | read-write | The value of tmnxOesSwUpgrade specifies an OES software upgrade where
the location of the software is specified by
tmnxSysSwReposPrimaryLocation, tmnxSysSwReposSecondaryLocation or
tmnxSysSwReposTertiaryLocation. This is a service affecting upgrade. |
| TNA tmnxOesSoftwareRepository | 1.3.6.1.4.1.6527.3.1.2.98.1.4 | TNamedItemOrEmpty | read-write | The value of tmnxOesSoftwareRepository specifies the software
repository to be used by OES.
An empty string indicates this object has not been configured. |
| TNA tmnxOesCtlCommsVRtrName | 1.3.6.1.4.1.6527.3.1.2.98.1.5 | TNamedItemOrEmpty | read-write | The value of tmnxOesCtlCommsVRtrName specifies the name of the virtual
router instance used in OES control communications.
An empty string indicates this object has not been configured. |
| IPt tmnxOesCtlCommsAddressType | 1.3.6.1.4.1.6527.3.1.2.98.1.6 | InetAddressType | read-write | The value of tmnxOesCtlCommsAddressType specifies the address
type of tmnxOesCtlCommsAddress. |
| IP tmnxOesCtlCommsAddress | 1.3.6.1.4.1.6527.3.1.2.98.1.7 | InetAddress | read-write | The value of tmnxOesCtlCommsAddress specifies the destination address
of the master OES used in OES control communications. |
| U32 tmnxOesCtlCommsTimeout | 1.3.6.1.4.1.6527.3.1.2.98.1.8 | Unsigned32 | read-write | The value of tmnxOesCtlCommsTimeout specifies the maximum amount
of time, in seconds, before declaring an individual request to
the OES has timeout. Such a failed request is retried a number
of times as specified by tmnxOesCtlCommsRetryLimit and the OES is
declared unreachable if all retries also timeout. |
| U32 tmnxOesCtlCommsRetryLimit | 1.3.6.1.4.1.6527.3.1.2.98.1.9 | Unsigned32 | read-write | The value of tmnxOesCtlCommsRetryLimit specifies the maximum
number of times the system will retry an attempt to communicate
with the OES chassis before declaring the OES as unreachable.
See also tmnxOesCtlCommsTimeout. |
| tmnxOesStatObjs | 1.3.6.1.4.1.6527.3.1.2.98.2 | | | |
| STR tmnxOesRunningSwImage | 1.3.6.1.4.1.6527.3.1.2.98.2.1 | DisplayString | read-only | The value of tmnxOesRunningSwImage indicates the version of the
software image running on PSS-1830. |
| INT tmnxOesCtlCommsStatus | 1.3.6.1.4.1.6527.3.1.2.98.2.2 | INTEGER | read-only | The value of tmnxOesCtlCommsStatus indicates the status of the
communication link with PSS-1830. |
| INT tmnxOesStatus | 1.3.6.1.4.1.6527.3.1.2.98.2.3 | INTEGER | read-only | The value of tmnxOesStatus indicates the operational status of the OES:
unprovisioned (0) - OES master chassis (oes-1) is not provisioned
discovering (1) - OES discovery is in progress
active (2) - OES is ready for operation
inactive (3) - OES control communication is down
provInProgress (4) - OES provisioning is in progress
swUpgradeInProgress (5) - OES software upgrade is in progress |
| INT tmnxOesNtpStatus | 1.3.6.1.4.1.6527.3.1.2.98.2.4 | INTEGER | read-only | The value of tmnxOesNtpStatus indicates the status of the Network
Timing Protocol (NTP) for the OES. |
| TMN tmnxOesUserPanelHwIndex | 1.3.6.1.4.1.6527.3.1.2.98.2.5 | TmnxHwIndexOrZero | read-only | The value of tmnxOesUserPanelHwIndex indicates the hardware index of
the OES user panel entry in the tmnxHwTable. This value will be 0
when the master OES chassis is not configured. |
| TMN tmnxOesUserPanelState | 1.3.6.1.4.1.6527.3.1.2.98.2.6 | TmnxDeviceState | read-only | The value of tmnxOesUserPanelState indicates the OES USERPNL's
operational state. |
| INT tmnxOesCtlCommsDownReason | 1.3.6.1.4.1.6527.3.1.2.98.2.7 | INTEGER | read-only | The value of tmnxOesCtlCommsDownReason indicates the reason for the
last time a loss of communication with the OES was detected.
Values:
unknownReason (0) - control communication failure for unknown
reason
adminReboot (1) - OES is rebooted via tmnxOesReboot
noResponse (2) - no response was received for SNMP packet
configFailed (3) - a SNMP SET, GET or GETNEXT during a
configuration action did not complete
correctly
invalidSystem (4) - the OES sysObjectID does not contain the
object identifier for a supported system
invalidSoftware (5) - the OES software version is below the
minimum supported version
oesUnreachable (6) - OES is unreachable
adminEcSwitchOver (7) - OES EC activity switch via
tmnxOesChassisActivitySwitch
ctlCommsUnprov (8) - missing or incomplete OES control
communications provisioning
clearActiveEcCard (9) - OES active EC clear via tmnxOesCardReboot |
| TMN tmnxOesSwUpgradeLastStatus | 1.3.6.1.4.1.6527.3.1.2.98.2.10 | TmnxOesSWMgmtStatus | read-only | The value of tmnxOesSwUpgradeLastStatus indicates the status of the
last OES software upgrade command tmnxOesSwUpgrade. |
| DAT tmnxOesSwUpgradeLastTime | 1.3.6.1.4.1.6527.3.1.2.98.2.11 | DateAndTime | read-only | The value of tmnxOesSwUpgradeLastTime indicates the time when the last
OES software upgrade tmnxOesSwUpgrade
was initiated. |
| TMN tmnxOesSwUpgradeCleanupLstStatus | 1.3.6.1.4.1.6527.3.1.2.98.2.12 | TmnxOesSWMgmtStatus | read-only | The value of tmnxOesSwUpgradeCleanupLstStatus indicates the status of
the most recent OES software upgrade cleanup process initiated by
the system due to upgrade failure on the remote node. |
| DAT tmnxOesSwUpgradeLastCompleteTime | 1.3.6.1.4.1.6527.3.1.2.98.2.13 | DateAndTime | read-only | The value of tmnxOesSwUpgradeLastCompleteTime indicates the time when
the last OES software upgrade tmnxOesSwUpgrade was completed. |
| STR tmnxOesExpectedSwImage | 1.3.6.1.4.1.6527.3.1.2.98.2.14 | DisplayString | read-only | The value of tmnxOesExpectedSwImage indicates the version of the
software image expected on PSS-1830. |
| tmnxOesNotifyObjs | 1.3.6.1.4.1.6527.3.1.2.98.3 | | | |
| TMN tmnxOesEventReason | 1.3.6.1.4.1.6527.3.1.2.98.3.1 | TmnxOesEventReason | accessible-for-notify | The value of tmnxOesEventReason indicates the reason for which
the notification is being triggered. |
| tmnxOesMIBNotifyPrefix | 1.3.6.1.4.1.6527.3.1.3.98 | | | |
| tmnxOesNotifications | 1.3.6.1.4.1.6527.3.1.3.98.0 | | | |
| NTF tmnxOesCtlCommsDown | 1.3.6.1.4.1.6527.3.1.3.98.0.1 | | | [CAUSE] The tmnxOesCtlCommsDown notification is generated when the
active CPM can't reach the OES master chassis.
[EFFECT] The OES can't be managed by the router.
[RECOVERY] Ensure that all control communications ports between the
router and the OES master chassis are correctly connected and test
the cables. |
| NTF tmnxOesCtlCommsUp | 1.3.6.1.4.1.6527.3.1.3.98.0.2 | | | [CAUSE] The tmnxOesCtlCommsUp notification is generated when the
active CPM can reach the OES master chassis.
[EFFECT] The OES can be managed by the router.
[RECOVERY] No recovery required. |
| NTF tmnxOesDbSyncFailure | 1.3.6.1.4.1.6527.3.1.3.98.0.3 | | | The active Equipment Controller is unable to synchronize its database
with the inactive Equipment Controller.
[CAUSE] The tmnxOesDbSyncFailure notification may be raised under the
following conditions:
1) An incorrectly seated Equipment Controller;
2) The software versions on the active and inactive Equipment
Controllers are not compatible;
3) A hardware problem with one or both controllers.
[EFFECT] The OES does not have redundancy protection between the two
Equipment Controller cards.
[RECOVERY] Proceed as follows to clear the Database Synchronization
Failed alarm:
1) Remove the Equipment Controller with the condition and examine
the connector on the back of the card for damage, including bent
or broken pins;
2) Examine the connector on the backplane for damage. If there is
damage to the backplane of the shelf, contact your service
representative;
3) Re-insert the Equipment Controller into its original slot and
allow the card to initialize;
4) Repeat Step 2) through Step 4) for the second Equipment
Controller;
5) Replace the Equipment Controller with the alarm condition with a
new unit. If the condition is not cleared, replace the second
Equipment Controller with a new unit.
Follow the return and repair process to return the faulty card to
an authorized repair center for replacement. |
| NTF tmnxOesDbSyncFailureClear | 1.3.6.1.4.1.6527.3.1.3.98.0.4 | | | [CAUSE] The tmnxOesDbSyncFailureClear notification is generated when
the active Equipment Controller is able to synchronize its database
with the inactive Equipment Controller.
[EFFECT] The active and inactive Equipment Controller's databases
are now synchronized.
[RECOVERY] No recovery required. |
| NTF tmnxOesDbInvalid | 1.3.6.1.4.1.6527.3.1.3.98.0.5 | | | [CAUSE] The tmnxOesDbInvalid notification may be raised under the
following conditions:
1) During initial installation, if the OES is not properly
commissioned;
2) The serial number in the database does not match that of the OES
either because the controller was replaced or the alarm card was
replaced;
3) A downgrade of OES software has occurred;
4) Equipment Controller is removed/reseated during a system process,
causing file corruption;
5) The database audit failed indicating some type of corruption of
the database.
[EFFECT] The OES is not in a normal operating mode. It does not have
the correct configuration and the state of its cards is unpredictable.
As a result, the OES will not boot normally and not all commands are
allowed.
[RECOVERY] A database corruption on the OES requires that the OES be
re-commissioned. The correct database is held in the host system so
it will be restored to the shelf once the existing database is cleared
and the host re-establishes communication with the OES. |
| NTF tmnxOesDbInvalidClear | 1.3.6.1.4.1.6527.3.1.3.98.0.6 | | | [CAUSE] The tmnxOesDbInvalidClear notification is generated when the
active Equipment Controller previously under tmnxOesDbInvalid
condition now contains a valid database.
[EFFECT] The OES active Equipment Controller's database is now valid.
[RECOVERY] No recovery is required. |
| NTF tmnxOesDbUnsync | 1.3.6.1.4.1.6527.3.1.3.98.0.7 | | | [CAUSE] The tmnxOesDbUnsync notification is generated when the active
and standby Equipment Controllers are not in sync.
[EFFECT] The OES does not have redundancy protection between the two
Equipment Controller cards. If a switchover were to occur, then the
database of the newly active controller might not reflect the latest
configuration.
[RECOVERY] Proceed as follows to clear the Database Unsynchronization
alarm:
1) Perform a warm reset of the standby controller;
2) If step 1 does not clear the alarm condition, then contact the
next level of technical support for help. |
| NTF tmnxOesDbUnsyncClear | 1.3.6.1.4.1.6527.3.1.3.98.0.8 | | | [CAUSE] The tmnxOesDbUnsyncClear notification is generated when the
previously out of sync database is now synchronized between the
active and standby Equipment Controller cards.
[EFFECT] The database is synchronized between the active and standby
Equipment Controller cards.
[RECOVERY] No recovery is required. |
| NTF tmnxOesSwUpgdFailed | 1.3.6.1.4.1.6527.3.1.3.98.0.9 | | | [CAUSE] The tmnxOesSwUpgdFailed notification is generated when a
failure occurs in upgrading a component in the OES. This notification
is applicable at the NE (Network Element) level and/or the card level.
[EFFECT] The component is not upgraded.
[RECOVERY]
1) Determine the reason the upgrade failed by checking the
tmnxOesEventReason. First clear the condition indicated by the
reason in the object tmnxOesEventReason.
2) Perform a soft reset on the card that failed to upgrade and try
the upgrade procedure again.
3) Perform a hard reset on the card that failed to upgrade and try
the upgrade procedure again.
4) Remove and re-insert the card that failed to upgrade and try the
upgrade procedure again.
5) Replace the card that failed to upgrade and try the upgrade
procedure again.
6) Inform the Nokia technical support team. |
| NTF tmnxOesNtpOutOfSync | 1.3.6.1.4.1.6527.3.1.3.98.0.10 | | | [CAUSE] The tmnxOesNtpOutOfSync notification is generated when NTP time
on the OES is not synchronized to the host router. The host router must
have NTP enabled and have recovered time from external time sources
(NTP to PTP). If there is no NTP time source for the router, it will
not serve time to the OES. In addition, once the NE is power cycled,
it takes approximately 20-30 minutes to initialize. Thereafter, time
synchronization will be completed, with a maximum delay time of 2-3
minutes.
[EFFECT] Timestamp of each event occurring on the OES may not be
exactly aligned with the host router.
[RECOVERY] Ensure the host router has NTP configured and a reachable
time source. Allow 40 minutes for the condition to clear. |
| NTF tmnxOesNtpSync | 1.3.6.1.4.1.6527.3.1.3.98.0.11 | | | [CAUSE] The tmnxOesNtpSync notification is generated when NTP on the
OES is synchronized to the host router. The host router is serving
acceptable time toward the OES and the OES has completed initial
acquisition of time from the host.
[EFFECT] None.
[RECOVERY] No recovery is required. |
| NTF tmnxOesSwBelowMinRev | 1.3.6.1.4.1.6527.3.1.3.98.0.12 | | | [CAUSE] The tmnxOesSwBelowMinRev notification is generated when the
version of the running OES software image is below the minimum expected
version.
[EFFECT] The OES may not be operating as expected.
[RECOVERY] Upgrade the OES to a software image that is equal to or
greater than the minimum expected version. |
| NTF tmnxOesFirmwareCondition | 1.3.6.1.4.1.6527.3.1.3.98.0.13 | | | [CAUSE] The tmnxOesFirmwareCondition notification is generated when the
firmware on the card has a condition that needs to be notified to
network administrator. The value of tmnxOesEventReason object specifies
the reason.
[EFFECT] Not all the features may be available.
[RECOVERY] Perform a hard reset of the card. If the condition
persists, then contact Nokia customer support. |
| NTF tmnxOesCfgFailNoMemory | 1.3.6.1.4.1.6527.3.1.3.98.0.14 | | | [CAUSE] The tmnxOesCfgFailNoMemory notification is generated when a
request to obtain dynamic memory to download a configuration to the
OES has failed.
[EFFECT] The configuration is not active in the OES.
[RECOVERY] This may be a temporary issue and the condition may clear
on its own. If the event is raised periodically, then there is a
permanent memory issue and the support organization should be
informed. |
| NTF tmnxOesCfgBlocked | 1.3.6.1.4.1.6527.3.1.3.98.0.15 | | | [CAUSE] This event tmnxOesCfgBlocked notification is generated when a
configuration being made in the OES is blocked.
[EFFECT] The configuration is not active in the OES.
[RECOVERY]
One possible reason for this configuration failure is if there is a card
present in the OES that is a supported card type but the router was not yet
aware of its presence. This condition should clear as soon as the router
becomes aware of the card. A second reason is when the supported card is
present and is misaligned with the configuration (e.g. card present in slot
3 and 4, yet configuration is oes-1/2 where the width of card is two slots).
This condition cannot be cleared automatically as the card has to be moved
to the correct slot (or the configuration has to be removed for card oes-1/3
via cli command ). A third reason is when there is an unsupported card type
in the OES that the router cannot manage. This condition cannot be cleared
automatically and the OES will need to be recommissioned to clear the
condition.
Note: services on cards not impacted by the unknown card type are not
affected. |
| NTF tmnxOesSwUpgdCleanupFailed | 1.3.6.1.4.1.6527.3.1.3.98.0.16 | | | [CAUSE] This event tmnxOesSwUpgdCleanupFailed notification is
generated when the operation to clean-up a failed software upgrade
fails. The reason for the failure is specified in the object
tmnxOesEventReason.
[EFFECT] The OES software revision cannot be determined and so
the operational state of the respective OES or OES card is
indeterminate.
[RECOVERY]
1) Determine the reason for the upgrade failure from
tmnxOesEventReason in the notification. First clear the
condition indicated by the reason.
2) Re-try the upgrade procedure.
3) Contact the Nokia technical support team if the re-try does
not fix the problem. |
