| OID symbolic | OID numeric | Type | Access | Description |
|---|
| NTF vrrpTrapProtoError | 1.3.6.1.2.1.68.0.3 | | | The error trap indicates that the sending agent has
encountered the protocol error indicated by
vrrpTrapProtoErrReason. |
| vrrpOperationsTable | 1.3.6.1.2.1.68.1.7 | | not-accessible | Unified Operations table for a VRRP router which
consists of a sequence (i.e., one or more conceptual
rows) of 'vrrpOperationsEntry' items which describe
the operational characteristics of a virtual router. |
| vrrpOperationsEntry | 1.3.6.1.2.1.68.1.7.1 | | not-accessible | An entry in the vrrpOperationsTable containing the
operational characteristics of a virtual router. On a
VRRP router, a given virtual router is identified by a
combination of the IP version, VRID and ifIndex.
ifIndex represents a physical interface of the router.
Note that rows in this table can be distinguished on a
multi-stacked device running VRRP over IPv4 and
IPv6 on the same physical interface.
Rows in the table cannot be modified unless the value
of 'vrrpOperationsState' has transitioned to
'initialize' |
| IPt vrrpOperationsInetAddrType | 1.3.6.1.2.1.68.1.7.1.1 | InetAddressType | not-accessible | The IP address type of VrrpOperationsEntry. This value
applies to both vrrpOperationsMasterIpAddr and
vrrpOperationsPrimaryIpAddr. |
| VRI vrrpOperationsVrId | 1.3.6.1.2.1.68.1.7.1.2 | VrId | not-accessible | This object contains the Virtual Router Identifier
(VRID). |
| MAC vrrpOperationsVirtualMacAddr | 1.3.6.1.2.1.68.1.7.1.3 | MacAddress | read-only | The virtual MAC address of the virtual router.
Although this object can be derived from the
'vrrpOperationsVrId' object, it is defined so that it
is easily obtainable by a management application and
can be included in VRRP-related SNMP notifications. |
| INT vrrpOperationsState | 1.3.6.1.2.1.68.1.7.1.4 | INTEGER | read-only | The current state of the virtual router. This object
has three defined values:
- `initialize', which indicates that the
virtual router is waiting for a startup event.
- `backup', which indicates the virtual router is
monitoring the availability of the master router.
- `master', which indicates that the virtual router
is forwarding packets for IP addresses that are
associated with this router. |
| U32 vrrpOperationsPriority | 1.3.6.1.2.1.68.1.7.1.5 | Unsigned32 | read-create | This object specifies the priority to be used for the
virtual router master election process. Higher values
imply higher priority.
A priority of '0', although not settable, is sent by
the master router to indicate that this router has
ceased to participate in VRRP and a backup virtual
router should transition to become a new master.
A priority of 255 is used for the router that owns the
associated IP address(es) for VRRP over IPv4 and hence
not settable.
A 'badValue(3)' should be returned when a user tries to
set 0 or 255 for this object. |
| I32 vrrpOperationsAddrCount | 1.3.6.1.2.1.68.1.7.1.6 | Integer32 | read-only | The number of IP addresses that are associated with
this virtual router. This number is equal to the
number of rows in the vrrpAssociatedIpAddrTable that
correspond to a given IP version/VRID/ifIndex. |
| IP vrrpOperationsMasterIpAddr | 1.3.6.1.2.1.68.1.7.1.7 | InetAddress | read-only | The master router's real IP address. Master router
would set this address to vrrpOperationsPrimaryIpAddr
while transitioning to master state. For backup
routers, this is the IP address listed as the source in
VRRP advertisement last received by this virtual
router. |
| IP vrrpOperationsPrimaryIpAddr | 1.3.6.1.2.1.68.1.7.1.8 | InetAddress | read-create | In the case where there are more than one IP
Address (associated IP addresses) for a given
`ifIndex', this object is used to specify the IP
address that will become the
'vrrpOperationsMasterIpAddr', should the virtual router
transition from backup state to master. |
| NUM vrrpOperationsAdvInterval | 1.3.6.1.2.1.68.1.7.1.9 | TimeInterval | read-create | The time interval, in centiseconds, between sending
advertisement messages. Only the master router sends
VRRP advertisements. |
| T/F vrrpOperationsPreemptMode | 1.3.6.1.2.1.68.1.7.1.10 | TruthValue | read-create | Controls whether a higher priority virtual router will
preempt a lower priority master. |
| T/F vrrpOperationsAcceptMode | 1.3.6.1.2.1.68.1.7.1.11 | TruthValue | read-create | Controls whether a virtual router in Master state
will accept packets addressed to the address owner's
IPv6 address as its own if it is not the IPv6 address
owner. Default is False.
This object is not relevant for rows representing VRRP
over IPv4 and should be set to false. |
| TIM vrrpOperationsUpTime | 1.3.6.1.2.1.68.1.7.1.12 | TimeStamp | read-only | This is the value of the `sysUpTime' object when this
virtual router (i.e., the `vrrpOperationsState')
transitioned out of `initialized'. |
| STO vrrpOperationsStorageType | 1.3.6.1.2.1.68.1.7.1.13 | StorageType | read-create | The storage type for this conceptual row. Write access
is not required. It is optional to support nonVolatile
StorageType enumeration. |
| ROW vrrpOperationsRowStatus | 1.3.6.1.2.1.68.1.7.1.14 | RowStatus | read-create | The RowStatus variable should be used in accordance to
installation and removal conventions for conceptual
rows. When `vrrpOperationsRowStatus' is set to
active(1), no other objects in the conceptual row can
be modified.
To create a row in this table, a manager sets this
object to either createAndGo(4) or createAndWait(5).
Until instances of all corresponding columns are
appropriately configured, the value of the
corresponding instance of the `vrrpOperationsRowStatus'
column will be read as notReady(3).
In particular, a newly created row cannot be made
active(1) until (minimally) the corresponding instance
of vrrpOperationsInetAddrType, vrrpOperationsVrId and
vrrpOperationsPrimaryIpAddr has been set and there is
at least one active row in the
`vrrpAssociatedIpAddrTable' defining an associated
IP address.
notInService(2) should be used to administratively
bring the row down.
A typical order of operation to add a row is:
1. Create a row in vrrpOperationsTable with
createAndWait(5).
2. Create one or more corresponding rows in
vrrpAssociatedIpAddrTable.
3. Populate the vrrpOperationsEntry.
4. set vrrpOperationsRowStatus to active(1).
A typical order of operation to delete an entry is:
1. Set vrrpOperationsRowStatus to notInService(2).
2. Set the corresponding rows in
vrrpAssociatedIpAddrTable to destroy(6) to delete the
entry.
3. set vrrpOperationsRowStatus to destroy(6) to delete
the entry. |
| vrrpAssociatedIpAddrTable | 1.3.6.1.2.1.68.1.8 | | not-accessible | The table of addresses associated with this virtual
router. |
| vrrpAssociatedIpAddrEntry | 1.3.6.1.2.1.68.1.8.1 | | not-accessible | An entry in the table contains an IP address that is
associated with a virtual router. The number of rows
for a given IP version, vrrpOperationsVrId and ifIndex will equal the
number of IP addresses associated (e.g., backed up) by
the virtual router (equivalent to
'vrrpOperationsIpAddrCount').
Rows in the table cannot be modified unless the value
of `vrrpOperationsState' has transitioned to
`initialize'. |
| IP vrrpAssociatedIpAddr | 1.3.6.1.2.1.68.1.8.1.1 | InetAddress | not-accessible | The assigned IP addresses that a virtual router is
responsible for backing up.
The size of this object is either 4 or 16 depending on
vrrpOperationsInetAddrType. |
| STO vrrpAssociatedStorageType | 1.3.6.1.2.1.68.1.8.1.2 | StorageType | read-create | The storage type for this conceptual row. Write access
is not required. It is optional to support nonVolatile
StorageType enumeration. |
| ROW vrrpAssociatedIpAddrRowStatus | 1.3.6.1.2.1.68.1.8.1.3 | RowStatus | read-create | The RowStatus variable, used according to
installation and removal conventions for conceptual
rows. To create a row in this table, a manager sets
this object to either createAndGo(4) or
createAndWait(5). Setting this object to active(1)
results in the addition of an associated address for a
virtual router. Setting this object to notInService(2)
results in administratively bringing down the row.
Destroying the entry or setting it to destroy(6)
removes the associated address from the virtual router.
The use of other values is implementation-dependent.
Only vrrpAssociatedStorageType can be modified when the
row is in active(1) state for Implementations
supporting write access to vrrpAssociatedStorageType
Implementations should not allow deletion of the last
row corresponding to an active row in
vrrpOperationsTable.
Refer to description of vrrpOperationsRowStatus for a
typical row creation and deletion scenarios. |
| INT vrrpNewMasterReason | 1.3.6.1.2.1.68.1.9 | INTEGER | read-only | This indicates the reason for tVrrpTrapNewMaster trap.
Used by tVrrpTrapNewMaster trap. The object can be
polled if the tVrrpTrapNewMaster trap is lost to identify
the reason for transmission. Backup router should
return notmaster(0) when pooled. |
| INT vrrpTrapProtoErrReason | 1.3.6.1.2.1.68.1.10 | INTEGER | accessible-for-notify | This indicates the reason for protocol error trap.
Used by vrrpTrapProtoError trap. |
| vrrpRouterStatisticsTable | 1.3.6.1.2.1.68.2.5 | | not-accessible | Table of virtual router statistics. |
| vrrpRouterStatisticsEntry | 1.3.6.1.2.1.68.2.5.1 | | not-accessible | An entry in the table, containing statistics
information about a given virtual router. |
| C32 vrrpStatisticsMasterTransitionsEx | 1.3.6.1.2.1.68.2.5.1.1 | Counter32 | read-only | The total number of times that this virtual router's
state has transitioned to MASTER.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpStatisticsDiscontinuityTime. |
| C32 vrrpStatisticsRcvdAdvertisements | 1.3.6.1.2.1.68.2.5.1.2 | Counter32 | read-only | The total number of VRRP advertisements received by
this virtual router.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpStatisticsDiscontinuityTime. |
| C32 vrrpStatisticsAdvIntervalErrors | 1.3.6.1.2.1.68.2.5.1.3 | Counter32 | read-only | The total number of VRRP advertisement packets
received for which the advertisement interval is
different than the one configured for the local virtual
router.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpStatisticsDiscontinuityTime. |
| C32 vrrpStatisticsIpTtlErrors | 1.3.6.1.2.1.68.2.5.1.4 | Counter32 | read-only | The total number of VRRP packets received by the
Virtual router with IPv4 TTL (for VRRP over IPv4) or
IPv6 Hop Limit (for VRRP over IPv6) not equal to 255.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpStatisticsDiscontinuityTime. |
| C32 vrrpStatisticsRcvdPriZeroPackets | 1.3.6.1.2.1.68.2.5.1.5 | Counter32 | read-only | The total number of VRRP packets received by the
virtual router with a priority of '0'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpStatisticsDiscontinuityTime. |
| C32 vrrpStatisticsSentPriZeroPackets | 1.3.6.1.2.1.68.2.5.1.6 | Counter32 | read-only | The total number of VRRP packets sent by the virtual
router with a priority of '0'.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpStatisticsDiscontinuityTime. |
| C32 vrrpStatisticsRcvdInvalidTypePkts | 1.3.6.1.2.1.68.2.5.1.7 | Counter32 | read-only | The number of VRRP packets received by the virtual
router with an invalid value in the 'type' field.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpStatisticsDiscontinuityTime. |
| C32 vrrpStatisticsAddressListErrors | 1.3.6.1.2.1.68.2.5.1.8 | Counter32 | read-only | The total number of packets received for which the
address list does not match the locally configured list
for the virtual router.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpStatisticsDiscontinuityTime. |
| C32 vrrpStatisticsPacketLengthErrors | 1.3.6.1.2.1.68.2.5.1.9 | Counter32 | read-only | The total number of packets received with a packet
length less than the length of the VRRP header.
Discontinuities in the value of this counter can occur
at re-initialization of the management system, and at
other times as indicated by the value of
vrrpStatisticsDiscontinuityTime. |
| C32 vrrpStatisticsRcvdInvalidAuthentications | 1.3.6.1.2.1.68.2.5.1.10 | Counter32 | read-only | The total number of packets received with an unknown
authentication type. |
| TIM vrrpStatisticsDiscontinuityTime | 1.3.6.1.2.1.68.2.5.1.11 | TimeStamp | read-only | The value of sysUpTime on the most recent occasion at
which any one or more of this entry's counters suffered
a discontinuity.
If no such discontinuities have occurred since the last
re-initialization of the local management subsystem,
then this object contains a zero value. |
| U32 vrrpStatisticsRefreshRate | 1.3.6.1.2.1.68.2.5.1.12 | Unsigned32 | read-only | The minimum reasonable polling interval for this entry.
This object provides an indication of the minimum
Amount of time required to update the counters in this
entry. |
| vrrpModuleFullCompliance | 1.3.6.1.2.1.68.3.1.2 | | | The compliance statement for both VRRP for IPv4 and
VRRP for IPv6 implementations. |
| vrrpModuleReadOnlyCompliance | 1.3.6.1.2.1.68.3.1.3 | | | When this MIB is implemented without support for read-
create (i.e. in read-only mode), then such an
implementation can claim read-only compliance. Such a
device can then be monitored but can not be configured
with this MIB. |
| vrrpOperationsGroup | 1.3.6.1.2.1.68.3.2.5 | | | Conformance group for VRRP over IPv4 and IPv6
operations. |
| vrrpStatisticsGroup | 1.3.6.1.2.1.68.3.2.6 | | | Conformance group for VRRP over IPv4 and IPv6
statistics. |
| vrrpTrapInfoGroup | 1.3.6.1.2.1.68.3.2.7 | | | Conformance group for objects contained in VRRP
notifications. |
| vrrpNotificationsGroup | 1.3.6.1.2.1.68.3.2.8 | | | The VRRP MIB Notification Group. |
| vrrpNotifyObjsGroup | 1.3.6.1.2.1.68.3.2.9 | | | Conformance group for Notify objects contained in VRRP
notifications. |
| timetraVrrpV3MibModule | 1.3.6.1.4.1.6527.1.1.3.57 | | | This MIB is based on the draft-ietf-vrrp-unified-mib-06.txt
and describes objects used for managing Virtual
Router Redundancy Protocol (VRRP) over IPv6 protocol.
A separate VRRP-MIB based on RFC2787 describes objects used for
managing VRRP over IPv4 protocol.
This MIB is subject to draft revisions and will be updated when
an RFC number is assigned to it.
Copyright (c) 2008-2011 Alcatel-Lucent. All rights reserved.
Reproduction of this document is authorized on the condition that
the foregoing copyright notice is included.
This SNMP MIB module (Specification) embodies Alcatel-Lucent's
proprietary intellectual property. Alcatel-Lucent retains
all title and ownership in the Specification, including any
revisions.
Alcatel-Lucent grants all interested parties a non-exclusive
license to use and distribute an unmodified copy of this
Specification in connection with management of Alcatel-Lucent
products, and without fee, provided this copyright notice and
license appear on all copies.
This Specification is supplied 'as is', and Alcatel-Lucent
makes no warranty, either express or implied, as to the use,
operation, condition, or performance of the Specification. |
