All MIBs › TIMETRA-OTU-MIB
Organization: Alcatel-Lucent
Last Updated: 2009-02-28
Category: MPLS, Nokia SR OS / Alcatel-Lucent 7750 SR, Optical Transport
Description: Manages Nokia/Alcatel-Lucent 7750 SR OTU optical transport unit interface configuration and alarms.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TIMETRA-OTU-MIB?
TIMETRA-OTU-MIB is a Nokia/Alcatel-Lucent proprietary SNMP module for SR OS that manages and monitors Optical Transport Unit (OTU) interfaces, which carry client signals over DWDM/optical transport networks using ITU-T G.709 framing. It exposes interface configuration (forward error correction mode, signal-fail/signal-degrade thresholds, data rate) as well as bit-error-rate (BER) threshold settings and configurable alarm behavior. Its core monitoring value is optical-transport fault detection: BER threshold crossings (SF/SD) and configured alarms reveal degrading optical signal quality before a link fails outright, functioning much like a hardware health/fault indicator for the optical layer. It is used alongside standard interface MIBs (IF-MIB) since each OTU interface corresponds to an ifIndex entry. It is deployed on Nokia 7750 SR/7450 routers and optical transport platforms carrying high-speed DWDM circuits in carrier backbones. Network engineers evaluating or troubleshooting this functionality can download the TIMETRA-OTU-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in TIMETRA-OTU-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Nokia/Alcatel-Lucent 7750 SR / 7450 ESS optical transport routers
- DWDM/OTN optical transport interfaces
Monitoring Examples
An operator polls tmnxOtuIfTable/tmnxOtuIfEntry to check tmnxOtuIfFecMode and tmnxOtuIfOtuOperDataRate against expected values for a given optical interface, and monitors tmnxOtuIfBerSfThreshold/tmnxOtuIfBerSdThreshold to see when a signal-fail or signal-degrade condition is configured to trigger. If tmnxOtuIfCfgAlarms shows an active alarm on an interface, that typically indicates the measured bit-error rate has crossed the configured SD/SF threshold, a leading indicator of optical link degradation. Comparing tmnxOtuIfTimeStamp across polls helps identify when the interface's OTU configuration was last modified relative to when the alarm appeared.
What Can Be Monitored
- FEC mode and OTU data rate
- signal-fail/signal-degrade BER thresholds
- configured optical alarms
- OTU interface row status and last-changed time
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| ifIndex | OBJECT-TYPE |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TimeStamp | |
| TruthValue |
From TIMETRA-GLOBAL-MIB
| timetraSRMIBModules | OBJECT-IDENTITY |
| tmnxSRConfs | OBJECT-IDENTITY |
| tmnxSRNotifyPrefix | OBJECT-IDENTITY |
| tmnxSRObjs | OBJECT-IDENTITY |
From TIMETRA-TC-MIB
| TmnxActionType |
How to Use in IPNetwork Monitor
Example using tmnxOtuIfRawStatsFECCorrZeros OID:
Select a Nokia/Alcatel-Lucent 7750 SR / 7450 ESS optical transport routers, DWDM/OTN interface (OTU signal-quality/BER-threshold status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type tmnxOtuIfRawStatsFECCorrZeros into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The value of tmnxOtuIfRawStatsFECCorrZeros indicates the number of Forward Error Correction (FEC) corrected zeros. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| tmnxOtuMIBModule | 1.3.6.1.4.1.6527.1.1.3.62 | This document is the SNMP MIB module to manage and provision the Optical Transport Unit (OTU) components of the Alcatel-Lucent SROS device. Copyright 2008-2011 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel-Lucent's proprietary intellectual property. Alcatel-Lucent retains all title and ownership in the Specification, including any revisions. Alcatel-Lucent grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel-Lucent products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel-Lucent makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification. | ||
| tmnxOtuConformance | 1.3.6.1.4.1.6527.3.1.1.62 | |||
| tmnxOtuCompliances | 1.3.6.1.4.1.6527.3.1.1.62.1 | |||
| tmnxOtuCompliance | 1.3.6.1.4.1.6527.3.1.1.62.1.1 | The compliance statement for revision 1.0 of TIMETRA-OTU-MIB. | ||
| tmnxOtuComplianceV8v0 | 1.3.6.1.4.1.6527.3.1.1.62.1.2 | The compliance statement for revision 8.0 of TIMETRA-OTU-MIB. | ||
| tmnxOtuGroups | 1.3.6.1.4.1.6527.3.1.1.62.2 | |||
| tmnxOtuIfBaseConfigGroup | 1.3.6.1.4.1.6527.3.1.1.62.2.1 | The group of objects for management of OTU interfaces for the 7x50. | ||
| tmnxOtuIfSMGroup | 1.3.6.1.4.1.6527.3.1.1.62.2.2 | The group of objects for management of Section Monitoring of OTU interfaces for the 7x50. | ||
| tmnxOtuStatsGroup | 1.3.6.1.4.1.6527.3.1.1.62.2.3 | The group of objects for monitoring statistics of OTU interfaces for the 7x50. | ||
| tmnxOtuNotificationGroup | 1.3.6.1.4.1.6527.3.1.1.62.2.4 | The group of notifications supporting management of OTU interfaces for the 7x50. | ||
| tmnxOtuGroupsV7v0 | 1.3.6.1.4.1.6527.3.1.1.62.2.5 | |||
| tmnxOtuGroupsV8v0 | 1.3.6.1.4.1.6527.3.1.1.62.2.6 | |||
| tmnxOtuIfBaseConfigGroupV8v0 | 1.3.6.1.4.1.6527.3.1.1.62.2.6.1 | The group of additional objects for management of OTU interfaces for the 7x50 in Release 8.0. | ||
| tmnxOtuIfSMGroupV8v0 | 1.3.6.1.4.1.6527.3.1.1.62.2.6.2 | The group of additional objects for management of Section Monitoring of OTU interfaces for the 7x50 in Release 8.0. | ||
| tmnxOtuStatsGroupV8v0 | 1.3.6.1.4.1.6527.3.1.1.62.2.6.3 | The group of additional objects for monitoring statistics of OTU interfaces for the 7x50 in Release 8.0. | ||
| tmnxOtuIfPMGroupV8v0 | 1.3.6.1.4.1.6527.3.1.1.62.2.6.4 | The group of objects for management of Path Monitoring of OTU interfaces for the 7x50 in Release 8.0. | ||
| tmnxOtuIfPSIGroupV8v0 | 1.3.6.1.4.1.6527.3.1.1.62.2.6.5 | The group of objects for management of Payload Structure Identifier of OTU interfaces for the 7x50 in Release 8.0. | ||
| tmnxOtuObsoleteV8v0Group | 1.3.6.1.4.1.6527.3.1.1.62.2.6.6 | The group of objects that were made obsolete for the 7x50 in Release 8.0. | ||
| tmnxOtuObjs | 1.3.6.1.4.1.6527.3.1.2.62 | |||
| tmnxOtuConfigurationTimeStamps | 1.3.6.1.4.1.6527.3.1.2.62.0 | |||
| TIM tmnxOtuIfTableLastChanged | 1.3.6.1.4.1.6527.3.1.2.62.0.1 | TimeStamp | read-only | The tmnxOtuIfTableLastChanged indicates the time, since system startup, when a row in the tmnxOtuIfTable last changed. |
| tmnxOtuConfigurations | 1.3.6.1.4.1.6527.3.1.2.62.1 | |||
| tmnxOtuIfTable | 1.3.6.1.4.1.6527.3.1.2.62.1.1 | not-accessible | The tmnxOtuIfTable consists of the interfaces using OTU encapsulation. | |
| tmnxOtuIfEntry | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1 | not-accessible | The tmnxOtuIfEntry contains information pertaining to an individual OTU encapsulated physical interface. Rows in this table are created and destroyed using the tmnxOtuIfRowStatus object. | |
| ROW tmnxOtuIfRowStatus | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.1 | RowStatus | read-create | The tmnxOtuIfRowStatus controls the creation and deletion of row entries in the tmnxOtuIfTable. Creating a row in the tmnxOtuIfTable using 'createAndGo (4)' enables OTU encapsulation for the interface. Deleting the row using 'destroy (6)' will disable the OTU encapsulation. If a physical port does not support the OTU encapsulation, an attempt to set the tmnxOtuIfRowStatus to a value of 'createAndGo (4)' will fail with an inconsistent value result. |
| TIM tmnxOtuIfTimeStamp | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.2 | TimeStamp | read-only | The tmnxOtuIfTimeStamp indicates the time, since system startup, of the last change to this row. |
| TMN tmnxOtuIfFecMode | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.3 | TmnxOtuFecMode | read-create | The tmnxOtuIfFecMode specifies the OTU encapsulation used by this interface. |
| TMN tmnxOtuIfSfSdMethod | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.4 | TmnxOtuSFSDMethod | read-create | The tmnxOtuIfSfSdMethod specifies the method on which to detect Signal Failure and Signal Degradation. |
| U32 tmnxOtuIfBerSfThreshold | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.5 | Unsigned32 | read-create | The value of tmnxOtuIfBerSfThreshold specifies the bit error rate(BER) threshold used to determine when to raise and clear otuBerSf/fecSf alarms. Bit error computed must reach/exceed the threshold value over a predefined period of time for the alarms to be raised. The tmnxOtuIfSfSdMethod defines how the bit error is computed and what values of tmnxOtuIfBerSfThreshold are allowed. The following table defines this dependency: tmnxOtuIfSfSdMethod Bit error calculation ------------------- ---------------------------------------------- fec (1) Each corrected bit counts as one bit error. bip8 (2) Each BIP8 coding violation counts as one bit error. |
| U32 tmnxOtuIfBerSdThreshold | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.6 | Unsigned32 | read-create | The value of tmnxOtuIfBerSdThreshold specifies the bit error rate(BER) threshold used to determine when to raise and clear otuBerSd/fecSd alarms. Bit error computed must reach/exceed the threshold value over a predefined period of time for the alarms to be raised. The tmnxOtuIfSfSdMethod defines how the bit error is computed and what values of tmnxOtuIfBerSdThreshold are allowed. The following table defines this dependency: tmnxOtuIfSfSdMethod Bit error calculation ------------------- ---------------------------------------------- fec (1) Each corrected bit counts as one bit error. bip8 (2) Each BIP8 coding violation counts as one bit error. |
| U32 tmnxOtuIfOtuOperDataRate | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.7 | Unsigned32 | read-only | The tmnxOtuIfOtuOperDataRate indicates the rate at which the OTU data is transmitted on the line. |
| TMN tmnxOtuIfOtu2LanDataRate | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.8 | TmnxOtu2LanDataRate | read-create | The value of tmnxOtuIfOtu2LanDataRate specifies the rate at which data is transmitted on the line. An interface that does not support OTU2 encapsulation will default, and be restricted to, the value of 'notApplicable (0)'. |
| TMN tmnxOtuIfCfgAlarms | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.9 | TmnxOtuAlarms | read-create | The value of tmnxOtuIfCfgAlarms specifies the alarms that are to be monitored by the OTU interface. If an alarm bit is set, then the corresponding alarm will raise/clear an alarm when its state changes. An unset bit specifies that the alarm corresponding with the bit will not alarm on its state transitions. |
| TMN tmnxOtuIfAlarmState | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.10 | TmnxOtuAlarms | read-only | The value of tmnxOtuIfAlarmState indicates which monitored alarms are raised against the OTU interface. |
| U32 tmnxOtuIfHoldTimeUp | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.11 | Unsigned32 | read-create | The value of tmnxOtuIfHoldTimeUp is used to configure the hold-timer for link up event dampening. This guards against reporting excessive interface transitions. This is implemented by not advertising subsequent transitions of the interface to upper layer protocols until the configured timer has expired. A value of zero (0) indicates that an up transition is reported immediately. |
| U32 tmnxOtuIfHoldTimeDown | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.12 | Unsigned32 | read-create | The value of tmnxOtuIfHoldTimeDown is used to configure the hold-timer for link down event dampening. This guards against reporting excessive interface transitions. This is implemented by not advertising subsequent transitions of the interface to upper layer protocols until the configured timer has expired. A value of zero (0) indicates that an up transition is reported immediately. |
| TMN tmnxOtuIfSmTtiTxMode | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.13 | TmnxOtuTtiMode | read-create | The value of tmnxOtuIfSmTtiTxMode specifies the type of Trail Trace Identifier (TTI) for the Section Monitoring (SM) in the OTU overhead. Specifying a tmnxOtuIfSmTtiTxMode value of 'auto (0)' along with tmnxOtuIfSmTtiTx set with a single octet of '0xFF' will revert the SM-TTI to the default: '////C' |
| STR tmnxOtuIfSmTtiTx | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.14 | TmnxOtuTtiString | read-create | The value of tmnxOtuIfSmTtiTx specifies the Trail Trace Identifier (TTI) for the Section Monitoring (SM) in the OTU overhead. This identifier can be a string or a non-printable sequence of bytes. Specifying a one octet string with the value '0xFF' along with a tmnxOtuIfSmTtiTxMode set to the value of 'auto (0)' will reset the TTI to the system generated value. |
| STR tmnxOtuIfSmTtiRx | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.15 | TmnxOtuTtiString | read-only | The value of tmnxOtuIfSmTtiRx indicates the Trail Trace Identifier (TTI) for the Section Monitoring (SM) in the received OTU overhead. |
| TMN tmnxOtuIfSmTtiExpMode | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.16 | TmnxOtuTtiMode | read-create | The value of tmnxOtuIfSmTtiExpMode specifies the type of expected Trail Trace Identifier (TTI) for the Section Monitoring (SM) in the OTU overhead. Specifying a tmnxOtuIfSmTtiExpMode value of 'auto (0)' along with tmnxOtuIfSmTtiExp set with a single octet of '0xFF' will revert the SM-TTI to the default which is 'all zeros' in tmnxOtuIfSmTtiExp. |
| TMN tmnxOtuIfSmTtiExpCopyRx | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.17 | TmnxActionType | read-create | tmnxOtuIfSmTtiExpCopyRx is used to copy the contents of tmnxOtuIfSmTtiRx into tmnxOtuIfSmTtiExp. |
| STR tmnxOtuIfSmTtiExp | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.18 | TmnxOtuTtiString | read-create | The value of tmnxOtuIfSmTtiExp specifies the Trail Trace Identifier (TTI) for the Section Monitoring (SM) that is expected to be received in the OTU overhead. A mismatch of the received and the expected SM TTI will cause an 'otuTim' alarm to be raised |
| TMN tmnxOtuIfPmTtiTxMode | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.19 | TmnxOtuTtiMode | read-create | The value of tmnxOtuIfSmTtiTxMode specifies the type of Trail Trace Identifier (TTI) for the Path Monitoring (PM) in the OTU overhead. Specifying a tmnxOtuIfPmTtiTxMode value of 'auto (0)' along with tmnxOtuIfPmTtiTx set with a single octet of '0xFF' will revert the PM-TTI to the default: '////C' |
| STR tmnxOtuIfPmTtiTx | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.20 | TmnxOtuTtiString | read-create | The value of tmnxOtuIfPmTtiTx specifies the Trail Trace Identifier (TTI) for the Path Monitoring (PM) in the OTU overhead. This identifier can be a string or a non-printable sequence of bytes. Specifying a one octet string with the value '0xFF' along with a tmnxOtuIfPmTtiTxMode set to the value of 'auto (0)' will reset the TTI to the system generated value. |
| STR tmnxOtuIfPmTtiRx | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.21 | TmnxOtuTtiString | read-only | The value of tmnxOtuIfPmTtiRx indicates the Trail Trace Identifier (TTI) for the Path Monitoring (PM) in the received OTU overhead. |
| TMN tmnxOtuIfPmTtiExpMode | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.22 | TmnxOtuTtiMode | read-create | The value of tmnxOtuIfPmTtiExpMode specifies the type of expected Trail Trace Identifier (TTI) for the Path Monitoring (PM) in the OTU overhead. Specifying a tmnxOtuIfPmTtiExpMode value of 'auto (0)' along with tmnxOtuIfPmTtiExp set with a single octet of '0xFF' will revert the PM-TTI to the default which is 'all zeros' in tmnxOtuIfPmTtiExp. |
| TMN tmnxOtuIfPmTtiExpCopyRx | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.23 | TmnxActionType | read-create | tmnxOtuIfPmTtiExpCopyRx is used to copy the contents of tmnxOtuIfPmTtiRx into tmnxOtuIfPmTtiExp. |
| STR tmnxOtuIfPmTtiExp | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.24 | TmnxOtuTtiString | read-create | The value of tmnxOtuIfPmTtiExp indicates the Trail Trace Identifier (TTI) for the Path Monitoring (PM) that is expected to be received in the OTU overhead. A mismatch of the received and the expected PM TTI will cause an 'oduTim' alarm to be raised |
| TMN tmnxOtuIfPsiTtiTxMode | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.25 | TmnxOtuTtiMode | read-create | The value of tmnxOtuIfSmTtiTxMode specifies the type of Trail Trace Identifier (TTI) for the Payload Structure Identifier (PSI) in the OTU overhead. Specifying a tmnxOtuIfPsiTtiTxMode value of 'auto (0)' along with tmnxOtuIfPsiTtiTx set with a single octet of '0xFF' will revert the PSI-TTI to the default: '////C' |
| STR tmnxOtuIfPsiTtiTx | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.26 | TmnxOtuTtiString | read-create | The value of tmnxOtuIfPsiTtiTx specifies the Trail Trace Identifier (TTI) for the Payload Structure Identifier (PSI) in the OTU overhead. This identifier can be a string or a non-printable sequence of bytes. Specifying a one octet string with the value '0xFF' along with a tmnxOtuIfPsiTtiTxMode set to the value of 'auto (0)' will reset the PSI Trace to the system generated value. |
| STR tmnxOtuIfPsiTtiRx | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.27 | TmnxOtuTtiString | read-only | The value of tmnxOtuIfPsiTtiRx indicates the Trail Trace Identifier (TTI) for the Payload Structure Identifier (PSI) in the received OTU overhead. |
| TMN tmnxOtuIfPsiTtiExpMode | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.28 | TmnxOtuTtiMode | read-create | The value of tmnxOtuIfPsiTtiExpMode specifies the type of expected Trail Trace Identifier (TTI) Payload Structure Identifier (PSI) in the OTU overhead. Specifying a tmnxOtuIfPsiTtiExpMode value of 'auto (0)' along with tmnxOtuIfPsiTtiExp set with a single octet of '0xFF' will revert the PSI-TTI to the default which is 'all zeros' in tmnxOtuIfPsiTtiExp. |
| TMN tmnxOtuIfPsiTtiExpCopyRx | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.29 | TmnxActionType | read-create | tmnxOtuIfPsiTtiExpCopyRx is used to copy the contents of tmnxOtuIfPsiTtiRx into tmnxOtuIfPsiTtiExp. |
| STR tmnxOtuIfPsiTtiExp | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.30 | TmnxOtuTtiString | read-create | The value of tmnxOtuIfPsiTtiExp indicates the Trail Trace Identifier (TTI) for the Payload Structure Identifier (PSI) that is expected to be received in the OTU overhead. A mismatch of the received and the expected PSI Trace will cause an 'opuTim' alarm to be raised |
| TMN tmnxOtuIfPsiPayloadTypeTx | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.31 | TmnxOtuPsiPayloadType | read-create | The value of tmnxOtuIfPsiPayloadTypeTx specifies the Payload Type in the transmitted OPU PSI overhead. Specifying a value 'auto (0)' will provision the standard defined payload type for the current OTU mode of operation. |
| TMN tmnxOtuIfPsiPayloadTypeRx | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.32 | TmnxOtuPsiPayloadType | read-only | The value of tmnxOtuIfPsiPayloadTypeRx indicates the Payload Type in the received OPU PSI overhead. |
| TMN tmnxOtuIfPsiPayloadTypeExp | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.33 | TmnxOtuPsiPayloadType | read-create | The value of tmnxOtuIfPsiPayloadTypeExp indicates the Payload Type that is expected to be received in the OPU PSI overhead. Specifying a value 'auto (0)' will provision the standard defined payload type for the current OTU mode of operation. A mismatch of the received and the expected Payload type will cause an 'opuPlm' alarm to be raised |
| T/F tmnxOtuIfGfpMappingEnable | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.34 | TruthValue | not-accessible | The value of tmnxOtuIfGfpMappingEnable specifies whether or not the GFP mapping mode of transporting 10GbE is enabled. |
| T/F tmnxOtuIfAsyncMappingEnable | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.35 | TruthValue | read-create | The value of tmnxOtuIfAsyncMappingEnable specifies whether or not the Asynchronous mapping mode of transporting the OTU client is enabled. When this value is set to false, the OTU client is client is mapped Synchronously. |
| TMN tmnxOtuIfSmTimReaction | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.36 | TmnxOtuTimReaction | read-create | The value of tmnxOtuIfSmTimReaction specifies the reaction that should be taken in the event of a Section Monitor Trace Inentifier Mismatch. Specifying a value 'none (0)' indicates that no reaction should occur and therefore the ingress data will be passed through in the event of a Section Monitor Trace Indentifier mismatch. Specifying a value 'squelch-rx (1)' indicates that the incoming data will be squelched and therefore the ingress data will be blocked with a maintenance signal in the event of a Section Monitor Trace Indentifier mismatch. |
| TMN tmnxOtuIfPmTimReaction | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.37 | TmnxOtuTimReaction | read-create | The value of tmnxOtuIfSmTimReaction specifies the reaction that should be taken in the event of a Path Monitor Trace Inentifier Mismatch. Specifying a value 'none (0)' indicates that no reaction should occur and therefore the ingress data will be passed through in the event of a Path Monitor Trace Indentifier mismatch. Specifying a value 'squelch-rx (1)' indicates that the incoming data will be squelched and therefore the ingress data will be blocked with a maintenance signal in the event of a Path Monitor Trace Indentifier mismatch. |
| TMN tmnxOtuIfPsiTimReaction | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.38 | TmnxOtuTimReaction | read-create | The value of tmnxOtuIfSmTimReaction specifies the reaction that should be taken in the event of a Payload Structure Identifier Trace Mismatch. Specifying a value 'none (0)' indicates that no reaction should occur and therefore the ingress data will be passed through in the event of a Payload Structure Identifier Trace mismatch. Specifying a value 'squelch-rx (1)' indicates that the incoming data will be squelched and therefore the ingress data will be blocked with a maintenance signal in the event of a Payload Structure Identifier Trace mismatch. |
| TMN tmnxOtuIfPsiPlmReaction | 1.3.6.1.4.1.6527.3.1.2.62.1.1.1.39 | TmnxOtuTimReaction | read-create | The value of tmnxOtuIfSmTimReaction specifies the reaction that should be taken in the event of a Payload Type mismatch. Specifying a value 'none (0)' indicates that no reaction should occur and therefore the ingress data will be passed through in the event of a Payload Type mismatch. Specifying a value 'squelch-rx (1)' indicates that the incoming data will be squelched and therefore the ingress data will be blocked with a maintenance signal in the event of a Payload Type mismatch. |
| tmnxOtuStatistics | 1.3.6.1.4.1.6527.3.1.2.62.2 | |||
| tmnxOtuIfRawStatsTable | 1.3.6.1.4.1.6527.3.1.2.62.2.1 | not-accessible | The tmnxOtuIfRawStatsTable consists of the raw statistics associated with the OTU interfaces contained in the tmnxOtuIfTable. | |
| tmnxOtuIfRawStatsEntry | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1 | not-accessible | The tmnxOtuIfRawStatsEntry stores the statistics for an individual OTU interface. tmnxOtuIfRawStatsEntry rows are created and destroyed by the system when rows are added or removed in the tmnxOtuIfTable. | |
| C32 tmnxOtuIfRawStatsFECCorrZerosEx | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.1 | Counter32 | read-only | The value of tmnxOtuIfRawStatsFECCorrZeros indicates the number of Forward Error Correction (FEC) corrected zeros. |
| C32 tmnxOtuIfRawStatsOFFECCorrZeros | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.2 | Counter32 | read-only | The value of tmnxOtuIfRawStatsOFFECCorrZeros indicates the number of times the tmnxOtuIfRawStatsFECCorrZeros overflowed. |
| C64 tmnxOtuIfRawStatsHCFECCorrZeros | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.3 | Counter64 | read-only | The value of tmnxOtuIfRawStatsHCFECCorrZeros indicates the High Capacity number of Forward Error Correction (FEC) corrected zeros. |
| C32 tmnxOtuIfRawStatsFECCorrOnes | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.4 | Counter32 | read-only | The value of tmnxOtuIfRawStatsFECCorrOnes indicates the number of Forward Error Correction (FEC) corrected ones. |
| C32 tmnxOtuIfRawStatsOFFECCorrOnes | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.5 | Counter32 | read-only | The value of tmnxOtuIfRawStatsFECCorrOnes indicates the number of times the tmnxOtuIfRawStatsFECCorrOnes overflowed. |
| C64 tmnxOtuIfRawStatsHCFECCorrOnes | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.6 | Counter64 | read-only | The value of tmnxOtuIfRawStatsFECCorrOnes indicates the High Capacity number of Forward Error Correction (FEC) corrected ones. |
| C32 tmnxOtuIfRawStatsFECUncorrSR | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.7 | Counter32 | read-only | The value of tmnxOtuIfRawStatsFECUncorrSR indicates the number of Forward Error Correction (FEC) Uncorrectable Sub-Rows. |
| C32 tmnxOtuIfRawStatsOFFECUncorrSR | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.8 | Counter32 | read-only | The value of tmnxOtuIfRawStatsOFFECUncorrSR indicates the number of times the tmnxOtuIfRawStatsFECUncorrSR overflowed. |
| C64 tmnxOtuIfRawStatsHCFECUncorrSR | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.9 | Counter64 | read-only | The value of tmnxOtuIfRawStatsHCFECUncorrSR indicates the High Capacity number of Forward Error Correction (FEC) Uncorrectable Sub-Rows. |
| C32 tmnxOtuIfRawStatsFECSES | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.10 | Counter32 | read-only | The value of tmnxOtuIfRawStatsFECSES indicates the number of Forward Error Correction (FEC) Severely Errors Seconds (SES). |
| C32 tmnxOtuIfRawStatsSMBIP8 | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.11 | Counter32 | read-only | The value of tmnxOtuIfRawStatsSMBIP8 indicates the number of Section Monitoring (SM) BIP8 errors. |
| C32 tmnxOtuIfRawStatsOFSMBIP8 | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.12 | Counter32 | read-only | The value of tmnxOtuIfRawStatsOFSMBIP8 indicates the number of times the tmnxOtuIfRawStatsSMBIP8 overflowed. |
| C64 tmnxOtuIfRawStatsHCSMBIP8 | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.13 | Counter64 | read-only | The value of tmnxOtuIfRawStatsHCSMBIP8 indicates the High Capacity number of Section Monitoring (SM) BIP8 errors. |
| C32 tmnxOtuIfRawStatsSMBEI | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.14 | Counter32 | read-only | The value of tmnxOtuIfRawStatsSMBEI indicates the number of Section Monitoring (SM) Backward Error Indication (BEI) errors. |
| C32 tmnxOtuIfRawStatsOFSMBEI | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.15 | Counter32 | read-only | The value of tmnxOtuIfRawStatsOFSMBEI indicates the number of times the tmnxOtuIfRawStatsSMBEI overflowed. |
| C64 tmnxOtuIfRawStatsHCSMBEI | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.16 | Counter64 | read-only | The value of tmnxOtuIfRawStatsHCSMBEI indicates the High Capacity number of Section Monitoring (SM) Backward Error Indication (BEI) errors. |
| C32 tmnxOtuIfRawStatsSMSES | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.17 | Counter32 | read-only | The value of tmnxOtuIfRawStatsSMSES indicates the number of Section Monitoring (SM) Severely Errored Seconds (SES). |
| C32 tmnxOtuIfRawStatsPMBIP8 | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.18 | Counter32 | read-only | The value of tmnxOtuIfRawStatsPMBIP8 indicates the number of Path Monitoring (PM) BIP8 errors. |
| C32 tmnxOtuIfRawStatsOFPMBIP8 | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.19 | Counter32 | read-only | The value of tmnxOtuIfRawStatsOFPMBIP8 indicates the number of times the tmnxOtuIfRawStatsPMBIP8 overflowed. |
| C64 tmnxOtuIfRawStatsHCPMBIP8 | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.20 | Counter64 | read-only | The value of tmnxOtuIfRawStatsHCPMBIP8 indicates the High Capacity number of Path Monitoring (PM) BIP8 errors. |
| C32 tmnxOtuIfRawStatsPMBEI | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.21 | Counter32 | read-only | The value of tmnxOtuIfRawStatsPMBEI indicates the number of Path Monitoring (PM) Backward Error Indication (BEI) errors. |
| C32 tmnxOtuIfRawStatsOFPMBEI | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.22 | Counter32 | read-only | The value of tmnxOtuIfRawStatsOFPMBEI indicates the number of times tmnxOtuIfRawStatsPMBEI overflowed. |
| C64 tmnxOtuIfRawStatsHCPMBEI | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.23 | Counter64 | read-only | The value of tmnxOtuIfRawStatsPMBEI indicates the High Capacity number of Path Monitoring (PM) Backward Error Indication (BEI) errors. |
| C32 tmnxOtuIfRawStatsPMSES | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.24 | Counter32 | read-only | The value of tmnxOtuIfRawStatsPMSES indicates the number of Path Monitoring (PM) Severely Errored Seconds (SES). |
| C32 tmnxOtuIfRawStatsFECES | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.25 | Counter32 | read-only | The value of tmnxOtuIfRawStatsFECES indicates the number of Forward Error Correction (FEC) Errors Seconds (ES). |
| C32 tmnxOtuIfRawStatsFECUAS | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.26 | Counter32 | read-only | The value of tmnxOtuIfRawStatsFECUAS indicates the number of Forward Error Correction (FEC) Unavailable Seconds (UAS). |
| C32 tmnxOtuIfRawStatsSMES | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.27 | Counter32 | read-only | The value of tmnxOtuIfRawStatsSMES indicates the number of Section Monitoring (SM) Errored Seconds (ES). |
| C32 tmnxOtuIfRawStatsSMUAS | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.28 | Counter32 | read-only | The value of tmnxOtuIfRawStatsSMUAS indicates the number of Section Monitoring (SM) Unavailable Seconds (UAS). |
| C32 tmnxOtuIfRawStatsPMES | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.29 | Counter32 | read-only | The value of tmnxOtuIfRawStatsPMES indicates the number of Path Monitoring (PM) Errored Seconds (ES). |
| C32 tmnxOtuIfRawStatsPMUAS | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.30 | Counter32 | read-only | The value of tmnxOtuIfRawStatsPMUAS indicates the number of Path Monitoring (PM) Unavailable Seconds (UAS). |
| C32 tmnxOtuIfRawStatsNPJ | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.31 | Counter32 | read-only | The value of tmnxOtuIfRawStatsNPJ indicates the number of Negative Pointer justifications that occured during the asynchronous demapping of the received payload inside the OTU frame. |
| C32 tmnxOtuIfRawStatsPPJ | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.32 | Counter32 | read-only | The value of tmnxOtuIfRawStatsPPJ indicates the number of Positive Pointer justifications that occured during the asynchronous demapping of the received payload inside the OTU frame. |
| C32 tmnxOtuIfRawStatsElapsedSec | 1.3.6.1.4.1.6527.3.1.2.62.2.1.1.33 | Counter32 | read-only | The value of tmnxOtuIfRawStatsElapsedSec indicates the number of Elapsed seconds since the last OTU raw statistics clearing. |
| tmnxOtuIfIntervalStatsTable | 1.3.6.1.4.1.6527.3.1.2.62.2.2 | not-accessible | The tmnxOtuIfIntervalStatsTable consists of the statistic elements associated with the OTU interfaces contained in the tmnxOtuIfTable. | |
| tmnxOtuIfIntervalStatsEntry | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1 | not-accessible | The tmnxOtuIfIntervalStatsEntry stores the statistics for an individual OTU interface per row. tmnxOtuIfIntervalStatsEntry objects are created and destroyed by the system when rows are added or removed in the tmnxOtuIfTable. | |
| U32 tmnxOtuIfIntvlStatsIndex | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.1 | Unsigned32 | not-accessible | The tmnxOtuIfIntvlStatsIndex specifies the 15 minute statistic snap-shot for the OTU interface. The interval index value of 0 specifies the current raw 15 minute statistic window. The value of one indicates the most recently completed 15 minute interval statistics snap-shot. The interval identified by N is the interval immediately preceding the one identified by N-1. |
| T/F tmnxOtuIfIntvlStatsIsValid | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.2 | TruthValue | read-only | The value of tmnxOtuIfIntvlStatsIsValid indicates whether or not the current statistics interval is valid. The raw interval (tmnxOtuIfIntvlStatsIndex set to 0) is always false. |
| C32 tmnxOtuIfIntvlStatsFECCorrZeros | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.3 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsFECCorrZeros indicates the number of Forward Error Correction (FEC) corrected zeros. |
| C32 tmnxOtuIfIntvlStatsFECCorrOnes | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.4 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsFECCorrOnes indicates the number of Forward Error Correction (FEC) corrected ones. |
| C32 tmnxOtuIfIntvlStatsFECUncorrSR | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.5 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsFECUncorrSR indicates the number of Forward Error Correction (FEC) Uncorrectable Sub-Rows. |
| C32 tmnxOtuIfIntvlStatsFECSES | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.6 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsFECSES indicates the number of Forward Error Correction (FEC) Severely Errors Seconds (SES). |
| C32 tmnxOtuIfIntvlStatsSMBIP8 | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.7 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsSMBIP8 indicates the number of Section Monitoring (SM) BIP8 errors. |
| C32 tmnxOtuIfIntvlStatsSMBEI | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.8 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsSMBEI indicates the number of Section Monitoring (SM) Backward Error Indication (BEI) errors. |
| C32 tmnxOtuIfIntvlStatsSMSES | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.9 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsSMSES indicates the number of Section Monitoring (SM) Severely Errored Seconds (SES). |
| C32 tmnxOtuIfIntvlStatsPMBIP8 | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.10 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsPMBIP8 indicates the number of Path Monitoring (PM) BIP8 errors. |
| C32 tmnxOtuIfIntvlStatsPMBEI | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.11 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsPMBEI indicates the number of Path Monitoring (PM) Backward Error Indication (BEI) errors. |
| C32 tmnxOtuIfIntvlStatsPMSES | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.12 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsPMSES indicates the number of Path Monitoring (PM) Severely Errored Seconds (SES). |
| C32 tmnxOtuIfIntvlStatsFECES | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.13 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsFECES indicates the number of Forward Error Correction (FEC) Errors Seconds (ES). |
| C32 tmnxOtuIfIntvlStatsFECUAS | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.14 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsFECUAS indicates the number of Forward Error Correction (FEC) Unavailable Seconds (UAS). |
| C32 tmnxOtuIfIntvlStatsSMES | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.15 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsSMES indicates the number of Section Monitoring (SM) Errored Seconds (ES). |
| C32 tmnxOtuIfIntvlStatsSMUAS | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.16 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsSMUAS indicates the number of Section Monitoring (SM) Unavailable Seconds (UAS). |
| C32 tmnxOtuIfIntvlStatsPMES | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.17 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsPMES indicates the number of Path Monitoring (PM) Errored Seconds (ES). |
| C32 tmnxOtuIfIntvlStatsPMUAS | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.18 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsPMUAS indicates the number of Path Monitoring (PM) Unavailable Seconds (UAS). |
| C32 tmnxOtuIfIntvlStatsNPJ | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.19 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsNPJ indicates the number of Negative Pointer justifications that occured during the asynchronous demapping of the received payload inside the OTU frame. |
| C32 tmnxOtuIfIntvlStatsPPJ | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.20 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsPPJ indicates the number of Positive Pointer justifications that occured during the asynchronous demapping of the received payload inside the OTU frame. |
| C32 tmnxOtuIfIntvlStatsElapsedSec | 1.3.6.1.4.1.6527.3.1.2.62.2.2.1.21 | Counter32 | read-only | The value of tmnxOtuIfIntvlStatsElapsedSec indicates the number of Elapsed seconds in the current statistics interval. |
| tmnxOtuNotifyPrefix | 1.3.6.1.4.1.6527.3.1.3.62 | |||
| tmnxOtuNotifications | 1.3.6.1.4.1.6527.3.1.3.62.0 | |||
| NTF tmnxOtuIfAlarmNotification | 1.3.6.1.4.1.6527.3.1.3.62.0.1 | The tmnxOtuIfAlarmNotification notification indicates that an OTU interface has experienced either a raising or clearing of an alarm in the Forward Error Correction (FEC), Section Monitoring (SM), Path Monitoring (PM) or Payload Monitoring (PSI) fields of the OTU frame. |
RFC description
Optical Transport Unit (OTU) component management and provisioning for Alcatel-Lucent SROS devices.
Start monitoring Nokia/Alcatel-Lucent 7750 SR / 7450 ESS optical transport routers, DWDM/OTN interfaces (OTU signal-quality/BER-threshold status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.