TIMETRA-L2TP-MIB

All MIBs › TIMETRA-L2TP-MIB

Organization: Alcatel-Lucent

Last Updated: 2011-02-01

Description: TIMETRA-L2TP-MIB module

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TIMETRA-L2TP-MIB?

TIMETRA-L2TP-MIB is Alcatel-Lucent/Nokia's SROS MIB for managing and provisioning Layer Two Tunneling Protocol (L2TP) on 7750 SR routers, used for tunneling PPP or other Layer 2 sessions over an IP network. It exposes a table of L2TP tunnel/group configuration objects covering administrative state, session limits, receive window size, AVP (attribute-value pair) handling policy, peer address change policy, and accounting policy association, along with a last-management-change timestamp. Its monitoring value is centered on tunneling service software status: an operator can confirm whether an L2TP tunnel group is administratively up, check whether it is near its configured session limit, and correlate recent configuration changes with observed tunnel behavior. It is a Nokia SROS proprietary MIB conceptually built on the IETF L2TP protocol standard (RFC 2661/3931) though not a direct extension of an existing IETF L2TP MIB. It is typically deployed by broadband/VPN service providers running L2TP tunnel aggregation on 7750 SR routers, where TIMETRA-L2TP-MIB SNMP monitoring tracks tunnel group state and session-limit utilization.

IPNetwork Monitor allows you to monitor SNMP objects defined in TIMETRA-L2TP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nokia/Alcatel-Lucent 7750 SR (SROS) router

Monitoring Examples

An administrator would poll tmnxL2tpTable entries for tmnxL2tpAdminState and tmnxL2tpSessionLimit to confirm a tunnel group is enabled and see how close active sessions are to its configured ceiling, while tmnxL2tpReceiveWindowSize and tmnxL2tpAvpExclude reveal protocol tuning that could affect throughput or interoperability with a peer LNS/LAC. Checking tmnxL2tpLastMgmtChange or tmnxL2tpTableLastCh against a recent outage would help correlate a tunnel disruption with a configuration change, and tmnxL2tpAccountingPolicy confirms whether session accounting is being applied for billing/troubleshooting. A tunnel group hitting its tmnxL2tpSessionLimit would explain new session setup failures reported by subscribers.

What Can Be Monitored

L2TP tunnel group administrative state
L2TP session count vs session limit
L2TP receive window size / AVP policy
last management change timestamp
L2TP accounting policy association

Imported Objects

From HCNUM-TC

CounterBasedGauge64

From IF-MIB

InterfaceIndexOrZero

From INET-ADDRESS-MIB

InetAddress
InetAddressIPv4
InetAddressPrefixLength
InetAddressType
InetPortNumber

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
TEXTUAL-CONVENTION
TimeStamp
TruthValue

From TIMETRA-CHASSIS-MIB

tmnxCardSlotNum	OBJECT-TYPE
tmnxChassisIndex	OBJECT-TYPE
tmnxMDASlotNum	OBJECT-TYPE

From TIMETRA-GLOBAL-MIB

timetraSRMIBModules	OBJECT-IDENTITY
tmnxSRConfs	OBJECT-IDENTITY
tmnxSRNotifyPrefix	OBJECT-IDENTITY
tmnxSRObjs	OBJECT-IDENTITY

From TIMETRA-PPP-MIB

TmnxPppCpState

From TIMETRA-SERV-MIB

iesIfIndex	OBJECT-TYPE
svcId	OBJECT-TYPE

From TIMETRA-TC-MIB

TBurstSizeBytesOverride
TCIRRateOverride
TDirection
TItemDescription
TNamedItem
TNamedItemOrEmpty
TPIRRateOverride
TQosOverrideType
TmnxAccessLoopEncapDataLink
TmnxAccessLoopEncaps1
TmnxAccessLoopEncaps2
TmnxActionType
TmnxAdminState
TmnxAncpStringOrZero
TmnxAppProfileStringOrEmpty
TmnxAsciiSpecification
TmnxBinarySpecification
TmnxDefSubIdSource
TmnxManagedRouteStatus
TmnxMlpppEpClass
TmnxOperState
TmnxPppNcpProtocol
TmnxPppoeSessionInfoOrigin
TmnxPppoeSessionType
TmnxPppoeUserNameOrEmpty
TmnxServId
TmnxSlaProfileStringOrEmpty
TmnxSubIdentStringOrEmpty
TmnxSubMgtIntDestIdOrEmpty
TmnxSubNasPortPrefixType
TmnxSubNasPortSuffixType
TmnxSubNasPortTypeType
TmnxSubProfileStringOrEmpty
TmnxSubRadServAlgorithm
TmnxVRtrIDOrZero

From TIMETRA-VRTR-MIB

vRtrID	OBJECT-TYPE
vRtrIfName	OBJECT-TYPE

How to Use in IPNetwork Monitor

Example using tmnxL2tpStatTotalTunnels OID:

Select a Nokia/Alcatel-Lucent 7750 SR (SROS) router (L2TP tunnel-group admin/session-limit status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type tmnxL2tpStatTotalTunnels into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The value of tmnxL2tpStatTotalTunnels indicates the total number of tunnel set up attempts since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
timetraL2tpMIBModule	1.3.6.1.4.1.6527.1.1.3.60			This document is the SNMP MIB module to manage and provision the Layer Two Tunneling Protocol (L2TP) for the Alcatel-Lucent SROS device. Copyright 2009-2012 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel-Lucent's proprietary intellectual property. Alcatel-Lucent retains all title and ownership in the Specification, including any revisions. Alcatel-Lucent grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel-Lucent products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel-Lucent makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
tmnxL2tpConformance	1.3.6.1.4.1.6527.3.1.1.60
tmnxL2tpCompliances	1.3.6.1.4.1.6527.3.1.1.60.1
tmnxL2tpCompliance	1.3.6.1.4.1.6527.3.1.1.60.1.1			The compliance statement for management of L2TP on Alcatel-Lucent SROS series systems.
tmnxL2tpStatCompliance	1.3.6.1.4.1.6527.3.1.1.60.1.2			The compliance statement for monitoring of L2TP on Alcatel-Lucent SROS series systems.
tmnxL2tpOpCompliance	1.3.6.1.4.1.6527.3.1.1.60.1.3			The compliance statement for L2TP operations on Alcatel-Lucent SROS series systems.
tmnxL2tpLnsCompliance	1.3.6.1.4.1.6527.3.1.1.60.1.4			The compliance statement for management of L2TP LNS on Alcatel-Lucent SROS series systems.
tmnxL2tpNotifyCompliance	1.3.6.1.4.1.6527.3.1.1.60.1.5			The compliance statement for L2TP notifications on Alcatel-Lucent SROS series systems.
tmnxL2tpV8v0Compliance	1.3.6.1.4.1.6527.3.1.1.60.1.6			The compliance statement for management of L2TP on Alcatel-Lucent SROS series systems.
tmnxL2tpStatV8v0Compliance	1.3.6.1.4.1.6527.3.1.1.60.1.7			The compliance statement for monitoring of L2TP on Alcatel-Lucent SROS series systems.
tmnxL2tpLnsV9v0Compliance	1.3.6.1.4.1.6527.3.1.1.60.1.10			The compliance statement for management of L2TP LNS on Alcatel-Lucent SROS series systems.
tmnxL2tpNotifyV9v0Compliance	1.3.6.1.4.1.6527.3.1.1.60.1.11			The compliance statement for L2TP notifications on Alcatel-Lucent SROS series systems.
tmnxL2tpMlpppCompliance	1.3.6.1.4.1.6527.3.1.1.60.1.12			The compliance statement for management of MLPPP (Multi Link Point to Point Protocol) for L2TP on Alcatel-Lucent SROS series systems.
tmnxL2tpV10v0Compliance	1.3.6.1.4.1.6527.3.1.1.60.1.13			The compliance statement for management of L2TP on Alcatel-Lucent SROS series systems.
tmnxL2tpNotifyV10v0Compliance	1.3.6.1.4.1.6527.3.1.1.60.1.14			The compliance statement for L2TP notifications on Alcatel-Lucent SROS series systems.
tmnxL2tpLnsV10v0Compliance	1.3.6.1.4.1.6527.3.1.1.60.1.15			The compliance statement for management of L2TP LNS on Alcatel-Lucent SROS series systems.
tmnxL2tpGroups	1.3.6.1.4.1.6527.3.1.1.60.2
tmnxL2tpCfgGroup	1.3.6.1.4.1.6527.3.1.1.60.2.1			The group of objects providing management of L2TP instances on Alcatel-Lucent SROS series systems.
tmnxL2tpTgCfgGroup	1.3.6.1.4.1.6527.3.1.1.60.2.2			The group of objects providing management of L2TP tunnel groups on Alcatel-Lucent SROS series systems.
tmnxL2tpTuCfgGroup	1.3.6.1.4.1.6527.3.1.1.60.2.3			The group of objects providing management of L2TP tunnels on Alcatel-Lucent SROS series systems.
tmnxL2tpStatGroup	1.3.6.1.4.1.6527.3.1.1.60.2.4			The group of objects providing monitoring of L2TP on Alcatel-Lucent SROS series systems.
tmnxL2tpTgStatGroup	1.3.6.1.4.1.6527.3.1.1.60.2.5			The group of objects providing monitoring of L2TP tunnel groups on Alcatel-Lucent SROS series systems.
tmnxL2tpPeerStatGroup	1.3.6.1.4.1.6527.3.1.1.60.2.7			The group of objects providing monitoring of L2TP peers on Alcatel-Lucent SROS series systems.
tmnxL2tpSeStatGroup	1.3.6.1.4.1.6527.3.1.1.60.2.8			The group of objects providing monitoring of L2TP sessions on Alcatel-Lucent SROS series systems.
tmnxL2tpPeerOpGroup	1.3.6.1.4.1.6527.3.1.1.60.2.9			The group of objects providing monitoring of L2TP peers on Alcatel-Lucent SROS series systems.
tmnxL2tpTgOpGroup	1.3.6.1.4.1.6527.3.1.1.60.2.10			The group of objects providing operations on L2TP tunnel groups on Alcatel-Lucent SROS series systems.
tmnxL2tpTuOpGroup	1.3.6.1.4.1.6527.3.1.1.60.2.11			The group of objects providing operations on L2TP tunnels on Alcatel-Lucent SROS series systems.
tmnxL2tpLnsIsaGroup	1.3.6.1.4.1.6527.3.1.1.60.2.12			The group of objects providing configuration of L2TP Integrated Service Adaptors (ISA) on Alcatel-Lucent SROS series systems.
tmnxL2tpLnsIsaStatGroup	1.3.6.1.4.1.6527.3.1.1.60.2.13			The group of objects providing monitoring of L2TP Integrated Service Adaptors (ISA) on Alcatel-Lucent SROS series systems.
tmnxL2tpLnsTgGroup	1.3.6.1.4.1.6527.3.1.1.60.2.14			The group of objects providing management of L2TP LNS tunnel groups on Alcatel-Lucent SROS series systems.
tmnxL2tpLnsTuGroup	1.3.6.1.4.1.6527.3.1.1.60.2.15			The group of objects providing management of L2TP LNS tunnels on Alcatel-Lucent SROS series systems.
tmnxL2tpLnsSeGroup	1.3.6.1.4.1.6527.3.1.1.60.2.16			The group of objects providing monitoring of L2TP LNS PPP sessions on Alcatel-Lucent SROS series systems.
tmnxL2tpCfgV8v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.17			The group of objects providing management of L2TP instances on Alcatel-Lucent SROS series systems release 8.0.
tmnxL2tpTuStatGroup	1.3.6.1.4.1.6527.3.1.1.60.2.18			The group of objects providing monitoring of L2TP tunnels on Alcatel-Lucent SROS series systems.
tmnxL2tpPeerStatV8v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.19			The group of objects providing monitoring of L2TP peers on Alcatel-Lucent SROS series systems.
tmnxL2tpLnsIfGroup	1.3.6.1.4.1.6527.3.1.1.60.2.20			The group of objects providing configuration of L2TP LNS group interfaces on Alcatel-Lucent SROS series systems.
tmnxL2tpStatV8v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.21			The group of objects providing monitoring of L2TP on Alcatel-Lucent SROS series systems release 8.0.
tmnxL2tpSeOpGroup	1.3.6.1.4.1.6527.3.1.1.60.2.22			The group of objects providing operations on L2TP sessions on Alcatel-Lucent SROS series systems.
tmnxL2tpLnsTgV9v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.30			The group of objects providing management of L2TP LNS tunnel groups on Alcatel-Lucent SROS series systems that were added in release 9.0.
tmnxL2tpLnsTuV9v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.31			The group of objects providing management of L2TP LNS tunnels on Alcatel-Lucent SROS series systems that were added in release 9.0.
tmnxL2tpLnsIfV9v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.32			The group of objects providing configuration of L2TP LNS group interfaces on Alcatel-Lucent SROS series systems.
tmnxL2tpMlpppGroup	1.3.6.1.4.1.6527.3.1.1.60.2.40			The group of objects providing management of MLPPP for L2TP tunnels on Alcatel-Lucent SROS series systems.
tmnxL2tpLnsSeV9v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.41			The group of objects providing monitoring of L2TP LNS PPP sessions in release 9.0 of Alcatel-Lucent SROS series systems.
tmnxL2tpFilterProfileV9v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.42			The group of objects providing configuration of Filter Profiles on Alcatel-Lucent SROS series systems.
tmnxL2tpTgV10v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.43			The group of objects providing management of L2TP LNS tunnel groups on Alcatel-Lucent SROS series systems that were added in release 10.0.
tmnxL2tpTuV10v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.44			The group of objects providing management of L2TP LNS tunnels on Alcatel-Lucent SROS series systems that were added in release 10.0.
tmnxL2tpAccountingGroup	1.3.6.1.4.1.6527.3.1.1.60.2.45			The group of objects providing management of RADIUS accounting for L2TP tunnels on Alcatel-Lucent SROS series systems.
tmnxL2tpLnsIsaV10v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.46			The group of objects providing configuration of L2TP Integrated Service Adaptors (ISA) added in release 10.0 of Alcatel-Lucent SROS series systems.
tmnxL2tpObsoletedObjsV9v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.97			The group of objects that were obsoleted in release 9.0 of Alcatel-Lucent SROS series systems.
tmnxL2tpObsoletedObjsV8v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.98			The group of objects that were obsoleted in release 8.0 of Alcatel-Lucent SROS series systems.
tmnxL2tpNotifyObjsGroup	1.3.6.1.4.1.6527.3.1.1.60.2.99			The group of notification objects supporting L2TP notifications on Alcatel-Lucent SROS series systems.
tmnxL2tpNotifyGroup	1.3.6.1.4.1.6527.3.1.1.60.2.100			The group of notifications supporting L2TP on Alcatel-Lucent SROS series systems.
tmnxL2tpNotifyV9v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.101			The group of notifications supporting L2TP on Alcatel-Lucent SROS series systems added in release 9.0.
tmnxL2tpNotifyObjsV9v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.102			The group of notification objects supporting L2TP notifications on Alcatel-Lucent SROS series systems added in release 9.0.
tmnxL2tpNotifyV10v0Group	1.3.6.1.4.1.6527.3.1.1.60.2.103			The group of notifications supporting L2TP on Alcatel-Lucent SROS series systems added in release 10.0.
tmnxL2tp	1.3.6.1.4.1.6527.3.1.2.60
tmnxL2tpObjs	1.3.6.1.4.1.6527.3.1.2.60.1
tmnxL2tpVrtrObjs	1.3.6.1.4.1.6527.3.1.2.60.1.1
tmnxL2tpVrtrCfgObjs	1.3.6.1.4.1.6527.3.1.2.60.1.1.1
tmnxL2tpTable	1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2		not-accessible	A table that contains L2TP configuration information about virtual routers. Rows in this table can be created or deleted via SNMP operations. Rows in this table are automatically deleted when the corresponding row in the vRtrConfTable is deleted. The conceptual row that corresponds to the Base router instance, however, is automatically created by the system, and cannot be created or deleted via SNMP operations.
tmnxL2tpEntry	1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1		not-accessible	L2TP specific information about a virtual router. Each entry represents a L2TP protocol instance.
TIM tmnxL2tpLastMgmtChange	1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.1	TimeStamp	read-only	The value of tmnxL2tpLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
TMN tmnxL2tpAdminState	1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.2	TmnxAdminState	read-write	The value of the object tmnxL2tpAdminState specifies the administrative state of this L2TP protocol instance.
TMN tmnxL2tpSessionLimit	1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.3	TmnxL2tpTunnelSessionLimit	read-write	The value of tmnxL2tpSessionLimit specifies the maximum number of sessions in this L2TP protocol instance.
TMN tmnxL2tpReceiveWindowSize	1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.4	TmnxL2tpReceiveWindowSize	read-write	The value of tmnxL2tpReceiveWindowSize specifies the Receive Window Size in this L2TP protocol instance. The value '0' is not allowed.
ROW tmnxL2tpRowStatus	1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.5	RowStatus	read-write	The value of tmnxL2tpRowStatus specifies the row status of this row.
TMN tmnxL2tpPeerAddrChangePlcy	1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.6	TmnxL2tpPeerAddrChangePolicy	read-write	The value of the object tmnxL2tpPeerAddrChangePlcy specifies what to do in case the system receives a L2TP response from another address than the one the request was sent to, for a tunnel in this L2TP protocol instance.
BIT tmnxL2tpAvpExclude	1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.7	Bits	read-write	The value of the object tmnxL2tpAvpExclude specifies what AVP's (Attribute Value Pairs) to exclude from L2TP control messages related to a session in this L2TP protocol instance.
TMN tmnxL2tpAvpCallingNumberSpec	1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.8	TmnxAsciiSpecification	read-write	The value of the object tmnxL2tpAvpCallingNumberSpec specifies what string to put in the Calling Number AVP, for L2TP control messages related to a session in this L2TP protocol instance. This value is not applicable if the 'callingNumber' bit is set in the object tmnxL2tpAvpExclude. ::= 'S' \| 'c' \| 's' \| 'r' 'S' - system name, the value of TIMETRA-CHASSIS-MIB::tmnxChassisName 'c' - Agent Circuit Id 's' - SAP ID, formatted as a character string 'r' - Agent Remote Id An empty string is not allowed. Example: '%S %s' means 'the system name, followed by a blank space, followed by the SAP ID formatted as a string'.
TNA tmnxL2tpAccountingPolicy	1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.10	TNamedItemOrEmpty	read-write	The value of the object tmnxL2tpAccountingPolicy specifies the RADIUS accounting policy to use in this L2TP protocol instance. It refers to a conceptual row in the tmnxL2tpApTable. The value of tmnxL2tpAccountingPolicy can be overruled by a non-empty value of tmnxL2tpTgCfgAccountingPolicy or tmnxL2tpTuCfgAccountingPolicy.
tmnxL2tpVrtrStatObjs	1.3.6.1.4.1.6527.3.1.2.60.1.1.2
tmnxL2tpStatTable	1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1		not-accessible	A table that contains L2TP configuration information about virtual routers. The system automatically creates an entry in this table for each virtual router where L2TP is supported. Only the Base router supports L2TP.
tmnxL2tpStatEntry	1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1		not-accessible	L2TP specific information about a virtual router. Each entry represents a L2TP protocol instance.
TIM tmnxL2tpStatCleared	1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.1	TimeStamp	read-only	The value of the object tmnxL2tpStatCleared indicates the value of sysUpTime when the system statistics were cleared. The value zero indicates that the system statistics have not been cleared since the last re-initialization of the local network management subsystem.
C32 tmnxL2tpStatTotalTunnelsEx	1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.2	Counter32	read-only	The value of tmnxL2tpStatTotalTunnels indicates the total number of tunnel set up attempts since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
C32 tmnxL2tpStatFailedTunnels	1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.3	Counter32	read-only	The value of tmnxL2tpStatFailedTunnels indicates the number of tunnels that failed to reach the established state since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
C32 tmnxL2tpStatFailedTuAuth	1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.4	Counter32	read-only	The value of tmnxL2tpStatFailedTuAuth indicates the number of tunnels that failed authentication since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
G32 tmnxL2tpStatActiveTunnels	1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.5	Gauge32	read-only	The value of tmnxL2tpStatActiveTunnels indicates the number of tunnels currently established.
C32 tmnxL2tpStatTotalSessions	1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.6	Counter32	read-only	The value of tmnxL2tpStatTotalSessions indicates the number of session creation attempts since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
C32 tmnxL2tpStatFailedSessions	1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.7	Counter32	read-only	The value of tmnxL2tpStatFailedSessions indicates the number of sessions that failed to reach the established state since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
G32 tmnxL2tpStatActiveSessions	1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.8	Gauge32	read-only	The value of tmnxL2tpStatActiveSessions indicates the number of sessions currently established.
G32 tmnxL2tpStatCurrentTunnels	1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.9	Gauge32	read-only	The value of tmnxL2tpStatCurrentTunnels indicates the actual number of tunnels.
G32 tmnxL2tpStatCurrentSessions	1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.10	Gauge32	read-only	The value of tmnxL2tpStatCurrentSessions indicates the actual number of sessions.
tmnxL2tpTgObjs	1.3.6.1.4.1.6527.3.1.2.60.1.2
tmnxL2tpTgCfgObjs	1.3.6.1.4.1.6527.3.1.2.60.1.2.1
tmnxL2tpTgCfgTable	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2		not-accessible	The L2TP Tunnel configuration table contains objects to configure L2TP Tunnel Groups.
tmnxL2tpTgCfgEntry	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1		not-accessible	Each conceptual row represents a Layer Two Tunneling Protocol Tunnel Group. Entries in this table can be created or deleted via SNMP operations.
TMN tmnxL2tpTgCfgName	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.1	TmnxL2tpTunnelGroupName	not-accessible	The value of the object tmnxL2tpTgCfgName specifies the string to identify this Layer Two Tunneling Protocol Tunnel Group.
ROW tmnxL2tpTgCfgRowStatus	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.2	RowStatus	read-create	The value of tmnxL2tpTgCfgRowStatus specifies the row status of this row.
TIM tmnxL2tpTgCfgLastMgmtChange	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.3	TimeStamp	read-only	The value of tmnxL2tpTgCfgLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
TIT tmnxL2tpTgCfgDescription	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.4	TItemDescription	read-create	The value of tmnxL2tpTgCfgDescription specifies the description of this Layer Two Tunneling Protocol Tunnel Group.
TMN tmnxL2tpTgCfgAdminState	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.5	TmnxAdminState	read-create	The value of tmnxL2tpTgCfgAdminState specifies the administrative state of this Layer Two Tunneling Protocol Tunnel Group.
TMN tmnxL2tpTgCfgSecret	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.6	TmnxL2tpAuthSecret	read-create	The value of the object tmnxL2tpTgCfgSecret specifies the password to be used for the authentication of the tunnels in this Layer Two Tunneling Protocol Tunnel Group. For any given tunnel in this group, the value of tmnxL2tpTgCfgSecret can be overruled with the value of tmnxL2tpTuCfgSecret. This object will always return an empty string on a read.
NUM tmnxL2tpTgCfgHelloInterval	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.7	TmnxL2tpTunnelHelloInterval	read-create	The value of tmnxL2tpTgCfgHelloInterval specifies the time interval between two consecutive tunnel Hello messages. A value of '-1' specifies that the keepalive function is disabled. The value '-2' is not allowed because this is the widest scope for TmnxL2tpTunnelHelloInterval.
TMN tmnxL2tpTgCfgIdleTO	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.8	TmnxL2tpTunnelIdleTO	read-create	The value of tmnxL2tpTgCfgIdleTO specifies the period of time that an established tunnel with no active sessions will persist before being disconnected. A value of -1 leaves the tunnel up indefinitely. The value '-2' is not allowed because this is the widest scope for TmnxL2tpTunnelIdleTO.
TMN tmnxL2tpTgCfgDestructTO	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.9	TmnxL2tpTunnelDestructTO	read-create	The value of tmnxL2tpTgCfgDestructTO specifies the period of time that the data of a disconnected tunnel will persist before being removed. The value '-2' is not allowed because this is the widest scope for TmnxL2tpTunnelDestructTO.
TMN tmnxL2tpTgCfgMaxRetxEstab	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.10	TmnxL2tpTunnelMaxRetx	read-create	The value of tmnxL2tpTgCfgMaxRetxEstab specifies the number of retries allowed for established tunnels before their control connection goes down. The value '-2' is not allowed because this is the widest scope.
TMN tmnxL2tpTgCfgMaxRetxNotEstab	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.11	TmnxL2tpTunnelMaxRetx	read-create	The value of tmnxL2tpTgCfgMaxRetxNotEstab specifies the number of retries allowed for unestablished tunnels before their control connection goes down. The value '-2' is not allowed because this is the widest scope.
TMN tmnxL2tpTgCfgSessionLimit	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.12	TmnxL2tpTunnelSessionLimit	read-create	The value of tmnxL2tpTgCfgSessionLimit specifies the maximum number of sessions in this Layer Two Tunneling Protocol Tunnel Group.
TMN tmnxL2tpTgCfgAvpHiding	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.13	TmnxL2tpAvpHidingMode	read-create	The value of the object tmnxL2tpTgCfgAvpHiding specifies the method to be used for the authentication of the tunnels in this Layer Two Tunneling Protocol Tunnel Group. The value 'default' is not allowed because this is the widest scope for TmnxL2tpAvpHidingMode.
TMN tmnxL2tpTgCfgSessionAssignMethod	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.14	TmnxL2tpSessionAssignMethod	read-create	The value of the object tmnxL2tpTgCfgSessionAssignMethod specifies the method to be used for the authentication of the tunnels in this Layer Two Tunneling Protocol Tunnel Group
TMN tmnxL2tpTgCfgLocalName	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.15	TmnxL2tpHostNameOrEmpty	read-create	The value of the object tmnxL2tpTgCfgLocalName specifies the host name used by this system for the tunnels in this Layer Two Tunneling Protocol Tunnel Group during the authentication phase of tunnel establishment. This object is related to the RADIUS attribute Tunnel-Client-Auth-ID. It can be used to distinguish tunnels. An empty string specifies that the system name (SNMPv2-MIB::sysName) is used.
TMN tmnxL2tpTgCfgDoChallenge	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.16	TmnxL2tpDoChallenge	read-create	The value of the object tmnxL2tpTgCfgDoChallenge specifies when challenge-response is to be used for the authentication of the tunnels in this Layer Two Tunneling Protocol Tunnel Group. The value 'default' is not allowed because this is the widest scope for TmnxL2tpDoChallenge.
TMN tmnxL2tpTgCfgReceiveWindowSize	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.17	TmnxL2tpReceiveWindowSize	read-create	The value of the object tmnxL2tpTgCfgReceiveWindowSize specifies the Receive Window Size of the tunnels in this L2TP Tunnel Group. The value zero specifies that the value must be set to the actual value of the object tmnxL2tpReceiveWindowSize.
TMN tmnxL2tpTgCfgIsaGrpId	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.19	TmnxL2tpIsaGrpIdOrZero	read-create	The value of tmnxL2tpTgCfgIsaGrpId specifies the L2TP Integrated Service Adaptor group for the tunnels in this L2TP Tunnel Group.
IPt tmnxL2tpTgCfgAddrType	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.20	InetAddressType	read-create	The value of tmnxL2tpTgCfgAddrType specifies the address type of tmnxL2tpTgCfgAddr.
IP tmnxL2tpTgCfgAddr	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.21	InetAddress	read-create	The value of tmnxL2tpTgCfgAddr specifies the local IP address of the tunnels in this L2TP Tunnel Group.
TMN tmnxL2tpTgCfgLoadBalanceMethod	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.25	TmnxL2tpIsaMdaLoadBalanceMethod	read-create	The value of the object tmnxL2tpTgCfgLoadBalanceMethod specifies the method to be used for load-balancing sessions across ISA MDA in this Layer Two Tunneling Protocol Tunnel Group. The value 'default' is not allowed.
TNA tmnxL2tpTgCfgAccountingPolicy	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.26	TNamedItemOrEmpty	read-create	The value of the object tmnxL2tpTgCfgAccountingPolicy specifies the RADIUS accounting policy to be used in this Layer Two Tunneling Protocol Tunnel Group. It refers to a conceptual row in the tmnxL2tpApTable. The value of tmnxL2tpTgCfgAccountingPolicy can be overruled by a non-empty value of tmnxL2tpTuCfgAccountingPolicy. An empty string specifies that the value of tmnxL2tpAccountingPolicy must be used.
tmnxL2tpLnsTgPppTable	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3		not-accessible	The L2TP Tunnel configuration table contains objects to configure PPP (Point to Point Protocol) on L2TP LNS Tunnel Groups. Entries in this table are automatically created and deleted by the system.
tmnxL2tpLnsTgPppEntry	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1		not-accessible	Each conceptual row represents PPP information about a Layer Two Tunneling Protocol LNS Tunnel Group.
TIM tmnxL2tpLnsTgPppLastMgmtChange	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.1	TimeStamp	read-only	The value of tmnxL2tpLnsTgPppLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
TNA tmnxL2tpLnsTgPppAuthPlcy	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.2	TNamedItemOrEmpty	read-create	The value of the object tmnxL2tpLnsTgPppAuthPlcy specifies the authentication policy used by this system for the tunnels in this L2TP LNS Tunnel Group during the authentication phase of tunnel establishment. An empty string specifies that no authentication policy is used.
TMN tmnxL2tpLnsTgPppAuthProtocol	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.3	TmnxL2tpPppAuthentication	read-create	The value of the object tmnxL2tpLnsTgPppAuthProtocol specifies for the tunnels in this L2TP LNS Tunnel Group what PPP authentication protocol(s) will be negotiated during the LCP phase. The value 'default' is not allowed.
TNA tmnxL2tpLnsTgPppUserDb	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.4	TNamedItemOrEmpty	read-create	The value of the object tmnxL2tpLnsTgPppUserDb specifies the local user database to use for PADI or PPP PAP/CHAP based authentication during the authentication phase of tunnel establishment. An empty string specifies that no local user database is used.
TMN tmnxL2tpLnsTgPppDefaultService	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.5	TmnxServId	read-create	The value of tmnxL2tpLnsTgPppDefaultService specifies the service ID of the service where the PPP sessions are established when the authentication server does not specify the service ID.
TNA tmnxL2tpLnsTgPppDefaultGroupIf	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.6	TNamedItemOrEmpty	read-create	The value of tmnxL2tpLnsTgPppDefaultGroupIf specifies the group interface where the PPP sessions are established when the authentication server does not specify the group interface.
TMN tmnxL2tpLnsTgPppProxyLcp	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.7	TmnxAlwaysOrNever	read-create	The value of tmnxL2tpLnsTgPppProxyLcp specifies if this system re-uses the result of the Link Control Protocol (LCP) negotiation done by the proxy (LAC). If the value of this object is 'always', the Proxy LCP AVPs received from the LAC are used to initiate the LCP on this system. If the value of this object is 'never', this system restarts the LCP negotiation with the remote system.
TMN tmnxL2tpLnsTgPppProxyAuth	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.8	TmnxAlwaysOrNever	read-create	The value of tmnxL2tpLnsTgPppProxyAuth specifies if this system re-uses the authentication done by the proxy (LAC). If the value of this object is 'always', the Authentication AVPs received from the LAC are accepted. If the value of this object is 'never', this system restarts the authentication of the remote system.
TMN tmnxL2tpLnsTgPppMtu	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.9	TmnxL2tpPppMtu	read-create	The value of tmnxL2tpLnsTgPppMtu specifies the MTU (Maximum Transmission Unit) for the tunnels in this L2TP LNS Tunnel Group. The value zero is not allowed.
NUM tmnxL2tpLnsTgPppLcpKaInterval	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.10	TmnxL2tpLcpKaInterval	read-create	The value of tmnxL2tpLnsTgPppLcpKaInterval specifies for the tunnels in this L2TP LNS Tunnel Group the time interval in seconds at which LCP echo requests are transmitted. The value '0' is not allowed.
TMN tmnxL2tpLnsTgPppLcpKaHoldUp	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.11	TmnxL2tpLcpKaHoldUpMplier	read-create	The value of tmnxL2tpLnsTgPppLcpKaHoldUp specifies for the tunnels in this L2TP LNS Tunnel Group how many LCP keepalive messages can be missed before the related session is brought down. The value '0' is not allowed.
TMN tmnxL2tpLnsTgPppIpcpSubnetNeg	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.13	TmnxAlwaysOrNever	read-create	The value of tmnxL2tpLnsTgPppIpcpSubnetNeg specifies for the tunnels in this L2TP LNS Tunnel Group if IPCP subnet negotiation is enabled.
tmnxL2tpTgMlpppTable	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4		not-accessible	The L2TP Tunnel configuration table contains objects to configure MLPPP (Multi Link Point to Point Protocol) on L2TP Tunnel Groups. Entries in this table are automatically created and deleted by the system.
tmnxL2tpTgMlpppEntry	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1		not-accessible	Each conceptual row represents MLPPP information about a Layer Two Tunneling Protocol LNS Tunnel Group.
TIM tmnxL2tpTgMlpppLastMgmtChange	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.1	TimeStamp	read-only	The value of tmnxL2tpTgMlpppLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
TMN tmnxL2tpTgMlpppAdminState	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.2	TmnxAdminState	read-create	The value of tmnxL2tpTgMlpppAdminState specifies the administrative state of MLPPP for this Layer Two Tunneling Protocol Tunnel Group.
U32 tmnxL2tpTgMlpppMaxLinks	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.3	Unsigned32	read-create	The value of the object tmnxL2tpTgMlpppMaxLinks specifies the maximum number of MLPPP links. The value of this object is only relevant for tunnels where this system performs the LNS role.
TMN tmnxL2tpTgMlpppInterleave	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.4	TmnxAlwaysOrNever	read-create	The value of tmnxL2tpTgMlpppInterleave specifies if this system applies Link Fragmentation and Interleaving to the traffic sent from the LNS to the LAC. If the value of this object is 'always', downstream traffic is fragmented and interleaved, meaning that (non-fragmented) realtime traffic is interleaved with fragments of non-realtime traffic. If the value of this object is 'never', downstream traffic is only fragmented but not reordered according to priority. The value of this object is only relevant for tunnels where this system performs the LNS role.
TMN tmnxL2tpTgMlpppMaxFragDelay	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.5	TmnxL2tpMlpppMaxFragDelay	read-create	The value of tmnxL2tpTgMlpppMaxFragDelay specifies the maximum delay for fragments for the tunnels in this L2TP LNS Tunnel Group. The value zero means 'no fragmentation'. The value of this object is only relevant for tunnels where this system performs the LNS role.
TMN tmnxL2tpTgMlpppReassemblyTo	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.6	TmnxL2tpMlpppReassemblyTimeout	read-create	The value of tmnxL2tpTgMlpppReassemblyTo specifies the reassembly timeout for fragments for the tunnels in this L2TP LNS Tunnel Group. The value zero is not allowed. The value of this object is only relevant for tunnels where this system performs the LNS role.
TMN tmnxL2tpTgMlpppShortSeqNumberRx	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.7	TmnxAlwaysOrNever	read-create	The value of tmnxL2tpTgMlpppShortSeqNumberRx specifies if this system requests to receive short sequence numbers from the peer. If the value of this object is 'always', this system includes the Short Sequence Number Header Format Option in its LCP configuration options. If the value of this object is 'never', this system does not includes the Short Sequence Number Header Format Option in its LCP configuration options. The value of this object is only relevant for tunnels where this system performs the LNS role.
NUM tmnxL2tpTgMlpppEpClass	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.8	TmnxL2tpMlpppEndpointClass	read-create	The value of tmnxL2tpTgMlpppEpClass specifies the type of endpoint. If the value of 'tmnxL2tpTgMlpppEpClass' is equal to 'ipv4Address', the address for the MLPPP Endpoint Discriminator Option is taken from tmnxL2tpTgMlpppEpIpv4Address. If the value of 'tmnxL2tpTgMlpppEpClass' is equal to 'macAddress', the address for the MLPPP Endpoint Discriminator Option is taken from tmnxL2tpTgMlpppEpMacAddress. If the value of 'tmnxL2tpTgMlpppEpClass' is equal to 'default', the MLPPP Endpoint Discriminator Option must not be transmitted. A value other than 'default' is only relevant for tunnels where this system performs the LNS role.
ADR tmnxL2tpTgMlpppEpIpv4Address	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.9	InetAddressIPv4	read-create	The value of tmnxL2tpTgMlpppEpIpv4Address specifies the class 2 address to use in the MLPPP Endpoint Discriminator Option. While the value of tmnxL2tpTgMlpppEpClass is equal to 'ipv4Address', a value of all zeroes specifies that the system IP address be used; otherwise, it means that no address is specified.
MAC tmnxL2tpTgMlpppEpMacAddress	1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.10	MacAddress	read-create	The value of tmnxL2tpTgMlpppEpMacAddress specifies the class 3 address to use in the MLPPP Endpoint Discriminator Option. While the value of tmnxL2tpTgMlpppEpClass is equal to 'macAddress', a value of all zeroes specifies that the system MAC address be used; otherwise, it means that no address is specified.
tmnxL2tpTgStatObjs	1.3.6.1.4.1.6527.3.1.2.60.1.2.2
tmnxL2tpTgStatTable	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1		not-accessible	The tmnxL2tpTgStatTable contains status and statistics information about Layer Two Tunneling Protocol Tunnel Groups. The tmnxL2tpTgStatTable has an entry for each L2TP Tunnel Group.
tmnxL2tpTgStatEntry	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1		not-accessible	Each row entry contains status and statistics about an L2TP tunnel group. Rows are created or removed automatically by the system.
TMN tmnxL2tpTgStatName	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.1	TmnxL2tpTunnelGroupName	not-accessible	The value of the object tmnxL2tpTgStatName indicates the string to identify this Layer Two Tunneling Protocol Tunnel Group.
TMN tmnxL2tpTgStatState	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.2	TmnxL2tpTgOperState	read-only	The value of tmnxL2tpTgStatState indicates the operational state of this Layer Two Tunneling Protocol Tunnel Group.
TIM tmnxL2tpTgStatCleared	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.3	TimeStamp	read-only	The value of the object tmnxL2tpTgStatCleared indicates the value of sysUpTime when the tunnel group statistics were cleared. The value zero indicates that the statistics have not been cleared since the last re-initialization of the local network management subsystem.
C32 tmnxL2tpTgStatTotalTunnels	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.4	Counter32	read-only	The value of tmnxL2tpTgStatTotalTunnels indicates the total number of tunnel set up attempts in this tunnel group since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
C32 tmnxL2tpTgStatFailedTunnels	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.5	Counter32	read-only	The value of tmnxL2tpTgStatFailedTunnels indicates the number of tunnels in this tunnel group that failed to reach the established state since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
C32 tmnxL2tpTgStatFailedTuAuth	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.6	Counter32	read-only	The value of tmnxL2tpTgStatFailedTuAuth indicates the number of tunnels in this tunnel group that failed authentication since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
G32 tmnxL2tpTgStatActiveTunnels	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.7	Gauge32	read-only	The value of tmnxL2tpTgStatActiveTunnels indicates the number of tunnels currently established in this tunnel group.
G32 tmnxL2tpTgStatTunnels	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.8	Gauge32	read-only	The value of tmnxL2tpTgStatTunnels indicates the actual number of tunnels in this tunnel group.
C32 tmnxL2tpTgStatTotalSessions	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.9	Counter32	read-only	The value of tmnxL2tpTgStatTotalSessions indicates the number of session creation attempts in this tunnel group since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
C32 tmnxL2tpTgStatFailedSessions	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.10	Counter32	read-only	The value of tmnxL2tpTgStatFailedSessions indicates the number of sessions in this tunnel group that failed to reach the established state since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
G32 tmnxL2tpTgStatActiveSessions	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.11	Gauge32	read-only	The value of tmnxL2tpTgStatActiveSessions indicates the number of sessions currently established in this tunnel group.
G32 tmnxL2tpTgStatSessions	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.12	Gauge32	read-only	The value of tmnxL2tpTgStatSessions indicates the actual number of sessions in this tunnel group.
NUM tmnxL2tpTgStatControlRxOctets	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.13	CounterBasedGauge64	read-only	The value of tmnxL2tpTgStatControlRxOctets indicates the number of control channel octets received by the current tunnels in this tunnel group.
G32 tmnxL2tpTgStatControlRxOctetsLw	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.14	Gauge32	read-only	The value of tmnxL2tpTgStatControlRxOctetsLw indicates the lower 32-bits word of the value of tmnxL2tpTgStatControlRxOctets.
G32 tmnxL2tpTgStatControlRxOctetsHw	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.15	Gauge32	read-only	The value of tmnxL2tpTgStatControlRxOctetsHw indicates the higher 32-bits word of the value of tmnxL2tpTgStatControlRxOctets.
G32 tmnxL2tpTgStatControlRxPkts	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.16	Gauge32	read-only	The value of tmnxL2tpTgStatControlRxPkts indicates the accumulated number of control packets received by the current tunnels in this tunnel group.
NUM tmnxL2tpTgStatControlTxOctets	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.17	CounterBasedGauge64	read-only	The value of tmnxL2tpTgStatControlTxOctets indicates the accumulated number of control channel octets that were transmitted to the current tunnel endpoints in this tunnel group.
G32 tmnxL2tpTgStatControlTxOctetsLw	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.18	Gauge32	read-only	The value of tmnxL2tpTgStatControlTxOctetsLw indicates the lower 32-bits word of the value of tmnxL2tpTgStatControlTxOctets.
G32 tmnxL2tpTgStatControlTxOctetsHw	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.19	Gauge32	read-only	The value of tmnxL2tpTgStatControlTxOctetsHw indicates the higher 32-bits word of the value of tmnxL2tpTgStatControlTxOctets.
G32 tmnxL2tpTgStatControlTxPkts	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.20	Gauge32	read-only	The value of tmnxL2tpTgStatControlTxPkts indicates the accumulated number of control packets that were transmitted to the current tunnel endpoints in this tunnel group.
G32 tmnxL2tpTgStatErrorTxPkts	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.21	Gauge32	read-only	The value of tmnxL2tpTgStatErrorTxPkts indicates the accumulated number of packet transmission errors on the current tunnels in this tunnel group.
G32 tmnxL2tpTgStatErrorRxPkts	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.22	Gauge32	read-only	The value of tmnxL2tpTgStatErrorRxPkts indicates the accumulated number of errored packets that were received on the current tunnels in this tunnel group.
G32 tmnxL2tpTgStatSessionLimit	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.23	Gauge32	read-only	The value of tmnxL2tpTgStatSessionLimit indicates the actual session limit of this tunnel group.
TMN tmnxL2tpTgStatSeAssignMethod	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.24	TmnxL2tpSessionAssignMethod	read-only	The value of the object tmnxL2tpTgStatSeAssignMethod indicates the latest actual method used for the authentication of the tunnels in this Layer Two Tunneling Protocol Tunnel Group. Note that the next tunnel that will be set up in this L2TP tunnel group may or may not use the same method, since the configuration of the RADIUS server may have changed in the meantime.
tmnxL2tpTgTuTable	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.2		not-accessible	The tmnxL2tpTgTuTable contains the set of active tunnels for each L2TP Tunnel Group.
tmnxL2tpTgTuEntry	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.2.1		not-accessible	Each row entry contains a tunnel identifier of an L2TP tunnel group. Rows are created or removed automatically by the system.
TMN tmnxL2tpTgTuId	1.3.6.1.4.1.6527.3.1.2.60.1.2.2.2.1.1	TmnxL2tpConnectionId	read-only	The value of the object tmnxL2tpTgTuId indicates the local identifier of a Layer Two Tunneling Protocol Tunnel. In L2TP version 2, it is the 16-bit tunnel ID. In L2TP version 3, it is the 32-bit control connection ID.
tmnxL2tpTgOpObjs	1.3.6.1.4.1.6527.3.1.2.60.1.2.3
tmnxL2tpTgDrainTable	1.3.6.1.4.1.6527.3.1.2.60.1.2.3.1		not-accessible	The tmnxL2tpTgDrainTable has an entry for each active Layer Two Tunneling Protocol Tunnel Group.
tmnxL2tpTgDrainEntry	1.3.6.1.4.1.6527.3.1.2.60.1.2.3.1.1		not-accessible	Each conceptual row presents an operations interface to drain a Layer Two Tunneling Protocol Tunnel Group. After a successful drain operation, the value of the object tmnxL2tpTgStatState of this tunnel group is equal to 'drain', and the value of the object tmnxL2tpTuStatusState is equal to 'draining' for all the tunnels of this L2TP tunnel group; none of these tunnels accept or establish new connections, while existing connections are timing out. Entries in this table are created and destroyed by the system.
TMN tmnxL2tpTgDrain	1.3.6.1.4.1.6527.3.1.2.60.1.2.3.1.1.1	TmnxL2tpActionTypeDrain	read-write	Setting this object to 'drain (0)' triggers an attempt to drain this L2TP tunnel group. Setting it to 'stopDrain (1)' stops the draining. Reading this object returns the value 'notApplicable'.
tmnxL2tpTunnelObjs	1.3.6.1.4.1.6527.3.1.2.60.1.3
tmnxL2tpTuCfgObjs	1.3.6.1.4.1.6527.3.1.2.60.1.3.1
tmnxL2tpTuCfgTable	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2		not-accessible	The L2TP Tunnel configuration table contains objects to configure L2TP Tunnels.
tmnxL2tpTuCfgEntry	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1		not-accessible	Each conceptual row represents a Layer Two Tunneling Protocol Tunnel. Entries in this table can be created or deleted via SNMP operations.
TNA tmnxL2tpTuCfgName	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.1	TNamedItem	not-accessible	The value of the object tmnxL2tpTuCfgName specifies the name of this Layer Two Tunneling Protocol Tunnel.
ROW tmnxL2tpTuCfgRowStatus	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.2	RowStatus	read-create	The value of tmnxL2tpTuCfgRowStatus specifies the row status of this row.
TIM tmnxL2tpTuCfgLastMgmtChange	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.3	TimeStamp	read-only	The value of tmnxL2tpTuCfgLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
TIT tmnxL2tpTuCfgDescription	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.4	TItemDescription	read-create	The value of tmnxL2tpTuCfgDescription specifies the description of this Layer Two Tunneling Protocol Tunnel.
TMN tmnxL2tpTuCfgAdminState	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.5	TmnxAdminState	read-create	The value of tmnxL2tpTuCfgAdminState specifies the administrative state of this Layer Two Tunneling Protocol Tunnel.
TMN tmnxL2tpTuCfgPreference	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.6	TmnxL2tpTunnelPreference	read-create	The value of tmnxL2tpTuCfgPreference specifies the preference of this Layer Two Tunneling Protocol Tunnel. The value '0' corresponds to the highest preference.
IPt tmnxL2tpTuCfgPeerAddrType	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.7	InetAddressType	read-create	The value of tmnxL2tpTuCfgPeerAddrType specifies the address type of tmnxL2tpTuCfgPeerAddr.
IP tmnxL2tpTuCfgPeerAddr	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.8	InetAddress	read-create	The value of tmnxL2tpTuCfgPeerAddr specifies the IP address of the peer.
IPt tmnxL2tpTuCfgAddrType	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.9	InetAddressType	read-create	The value of tmnxL2tpTuCfgAddrType specifies the address type of tmnxL2tpTuCfgAddr. The value 'unknown' specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgAddrType.
IP tmnxL2tpTuCfgAddr	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.10	InetAddress	read-create	The value of tmnxL2tpTuCfgAddr specifies the local IP address of this Layer Two Tunneling Protocol Tunnel. The value ''H specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgAddr.
TMN tmnxL2tpTuCfgLocalName	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.11	TmnxL2tpHostNameOrEmpty	read-create	The value of the object tmnxL2tpTuCfgLocalName specifies the host name used by this system during the authentication phase of tunnel establishment. This object is related to the RADIUS attribute Tunnel-Client-Auth-ID. It can be used to distinguish tunnels. An empty string specifies that the value of the object tmnxL2tpTgCfgLocalName is used.
TMN tmnxL2tpTuCfgRemoteName	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.12	TmnxL2tpHostNameOrEmpty	read-create	The value of the object tmnxL2tpTuCfgRemoteName specifies a string to be compared to the host name used by the tunnel peer during the authentication phase of tunnel establishment. This object is related to the RADIUS attribute Tunnel-Server-Auth-ID. It can be used to distinguish tunnels.
TMN tmnxL2tpTuCfgSecret	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.13	TmnxL2tpAuthSecret	read-create	The value of the object tmnxL2tpTuCfgSecret specifies the password to be used for the authentication of this Layer Two Tunneling Protocol Tunnel. This value overrules the value of the object tmnxL2tpTgCfgSecret of the tunnel group this tunnel belongs to. This object will always return an empty string on a read.
NUM tmnxL2tpTuCfgHelloInterval	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.14	TmnxL2tpTunnelHelloInterval	read-create	The value of tmnxL2tpTuCfgHelloInterval specifies the time interval between two consecutive tunnel Hello messages. A value of '-1' specifies that the keepalive function is disabled. A value of '-2' specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgHelloInterval.
TMN tmnxL2tpTuCfgIdleTO	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.15	TmnxL2tpTunnelIdleTO	read-create	The value of tmnxL2tpTuCfgIdleTO specifies the period of time that an established tunnel with no active sessions will persist before being disconnected. A value of -1 leaves the tunnel up indefinitely. A value of '-2' specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgIdleTO.
TMN tmnxL2tpTuCfgDestructTO	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.16	TmnxL2tpTunnelDestructTO	read-create	The value of tmnxL2tpTuCfgDestructTO specifies the period of time that data of a disconnected tunnel will persist before being removed. A value of '-2' specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgDestructTO.
TMN tmnxL2tpTuCfgMaxRetxEstab	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.17	TmnxL2tpTunnelMaxRetx	read-create	The value of tmnxL2tpTuCfgMaxRetxEstab specifies the number of retries allowed for this Layer Two Tunneling Protocol Tunnel while it is established, before its control connection goes down.
TMN tmnxL2tpTuCfgMaxRetxNotEstab	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.18	TmnxL2tpTunnelMaxRetx	read-create	The value of tmnxL2tpTuCfgMaxRetxNotEstab specifies the number of retries allowed for this Layer Two Tunneling Protocol Tunnel while it is unestablished, before its control connection goes down.
TMN tmnxL2tpTuCfgSessionLimit	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.19	TmnxL2tpTunnelSessionLimit	read-create	The value of tmnxL2tpTuCfgSessionLimit specifies the maximum number of sessions allowed in this Layer Two Tunneling Protocol Tunnel.
TMN tmnxL2tpTuCfgAvpHiding	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.20	TmnxL2tpAvpHidingMode	read-create	The value of tmnxL2tpTuCfgAvpHiding specifies when the H bit in the header of each Attribute Value Pair (AVP) is set for the L2TP control messages related to this Layer Two Tunneling Protocol Tunnel. The value 'default' specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgAvpHiding of the tunnel group this tunnel belongs to.
T/F tmnxL2tpTuCfgAutoEstab	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.21	TruthValue	read-create	The value of tmnxL2tpTuCfgAutoEstab specifies if this Layer Two Tunneling Protocol Tunnel is to be set up automatically by the system.
TMN tmnxL2tpTuCfgDoChallenge	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.22	TmnxL2tpDoChallenge	read-create	The value of tmnxL2tpTuCfgDoChallenge specifies when challenge-response is to be used for the authentication of this Layer Two Tunneling Protocol Tunnel. The value 'default' specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgDoChallenge of the tunnel group this tunnel belongs to.
TMN tmnxL2tpTuCfgReceiveWindowSize	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.23	TmnxL2tpReceiveWindowSize	read-create	The value of tmnxL2tpTuCfgReceiveWindowSize specifies the Receive Window Size for this Layer Two Tunneling Protocol Tunnel. The value zero specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgReceiveWindowSize.
TMN tmnxL2tpTuCfgIsaGrpId	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.24	TmnxL2tpIsaGrpIdOrZero	read-create	The value of tmnxL2tpTuCfgDoChallenge specifies the L2TP Integrated Service Adaptor group of this Layer Two Tunneling Protocol Tunnel. The value zero specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgIsaGrpId of the tunnel group this tunnel belongs to.
TMN tmnxL2tpTuCfgLoadBalanceMethod	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.30	TmnxL2tpIsaMdaLoadBalanceMethod	read-create	The value of the object tmnxL2tpTuCfgLoadBalanceMethod specifies the method to be used for load-balancing sessions across ISA MDA in this Layer Two Tunneling Protocol Tunnel. The value 'default' specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgLoadBalanceMethod of the tunnel group this tunnel belongs to.
TNA tmnxL2tpTuCfgAccountingPolicy	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.31	TNamedItemOrEmpty	read-create	The value of the object tmnxL2tpTuCfgAccountingPolicy specifies the RADIUS accounting policy to be used in this Layer Two Tunneling Protocol Tunnel. It refers to a conceptual row in the tmnxL2tpApTable. An empty string specifies that the value of tmnxL2tpTgCfgAccountingPolicy must be used
tmnxL2tpLnsTuPppTable	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3		not-accessible	The L2TP Tunnel configuration table contains objects to configure PPP (Point to Point Protocol) on L2TP LNS Tunnels. Entries in this table are automatically created and deleted by the system.
tmnxL2tpLnsTuPppEntry	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1		not-accessible	Each conceptual row represents PPP information about a Layer Two Tunneling Protocol LNS Tunnel configuration.
TIM tmnxL2tpLnsTuPppLastMgmtChange	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.1	TimeStamp	read-only	The value of tmnxL2tpLnsTuPppLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
TNA tmnxL2tpLnsTuPppAuthPlcy	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.2	TNamedItemOrEmpty	read-create	The value of the object tmnxL2tpLnsTuPppAuthPlcy specifies the authentication policy used by this system during the authentication phase of session establishment. An empty string specifies that the actual value must be used of the object tmnxL2tpLnsTgPppAuthPlcy of the tunnel group this tunnel configuration belongs to.
TMN tmnxL2tpLnsTuPppAuthProtocol	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.3	TmnxL2tpPppAuthentication	read-create	The value of tmnxL2tpLnsTuPppAuthProtocol specifies what PPP authentication protocol(s) will be negotiated during the LCP phase for the sessions of this tunnel. The value zero specifies that the actual value must be used of the object tmnxL2tpLnsTgPppAuthProtocol.
TNA tmnxL2tpLnsTuPppUserDb	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.4	TNamedItemOrEmpty	read-create	The value of the object tmnxL2tpLnsTuPppUserDb specifies the local user database to use for PADI or PPP PAP/CHAP based authentication during the authentication phase of session establishment. An empty string specifies that the actual value must be used of the object tmnxL2tpLnsTgPppUserDb of the tunnel group this tunnel configuration belongs to.
TMN tmnxL2tpLnsTuPppDefaultService	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.5	TmnxServId	read-create	The value of tmnxL2tpLnsTuPppDefaultService specifies the service ID of the service where the PPP sessions are established when the authentication server does not specify the service ID. The value zero specifies that that the actual value must be used of the object tmnxL2tpLnsTgPppDefaultService. If the value of tmnxL2tpLnsTuPppDefaultService is equal to zero, the value of tmnxL2tpLnsTuPppDefaultGroupIf must also be equal to zero.
TNA tmnxL2tpLnsTuPppDefaultGroupIf	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.6	TNamedItemOrEmpty	read-create	The value of tmnxL2tpLnsTuPppDefaultGroupIf specifies the group interface where the PPP sessions are established when the authentication server does not specify the group interface. The empty string specifies that the actual value must be used of the object tmnxL2tpLnsTgPppDefaultGroupIf. If the value of tmnxL2tpLnsTuPppDefaultGroupIf is equal to zero, the value of tmnxL2tpLnsTuPppDefaultService must also be equal to zero.
TMN tmnxL2tpLnsTuPppProxyLcp	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.7	TmnxAlwaysNeverOrDefault	read-create	The value of tmnxL2tpLnsTuPppProxyLcp specifies if this system re-uses the result of the Link Control Protocol (LCP) negotiation done by the proxy (LAC). If the value of this object is 'always', the Proxy LCP AVPs received from the LAC are used to initiate the LCP on this system. If the value of this object is 'never', this system restarts the LCP negotiation with the remote system. The value 'default' specifies that the actual value must be used of the object tmnxL2tpLnsTgPppProxyLcp.
TMN tmnxL2tpLnsTuPppProxyAuth	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.8	TmnxAlwaysNeverOrDefault	read-create	The value of tmnxL2tpLnsTuPppProxyAuth specifies if this system re-uses the authentication done by the proxy (LAC). If the value of this object is 'always', the Authentication AVPs received from the LAC are accepted. If the value of this object is 'never', this system restarts the authentication of the remote system. The value 'default' specifies that the actual value must be used of the object tmnxL2tpLnsTgPppProxyAuth.
TMN tmnxL2tpLnsTuPppMtu	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.9	TmnxL2tpPppMtu	read-create	The value of tmnxL2tpLnsTuPppMtu specifies the MTU (Maximum Transmission Unit) for this tunnel. The value zero specifies that the actual value must be used of the object tmnxL2tpLnsTgPppMtu.
NUM tmnxL2tpLnsTuPppLcpKaInterval	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.10	TmnxL2tpLcpKaInterval	read-create	The value of tmnxL2tpLnsTuPppLcpKaInterval specifies the time interval in seconds at which LCP echo requests are transmitted for this tunnel. The value zero specifies that the actual value must be used of the object tmnxL2tpLnsTgPppLcpKaInterval. If the value of tmnxL2tpLnsTuPppLcpKaInterval is equal to zero, the value of tmnxL2tpLnsTuPppLcpKaHoldUp must also be equal to zero.
TMN tmnxL2tpLnsTuPppLcpKaHoldUp	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.11	TmnxL2tpLcpKaHoldUpMplier	read-create	The value of tmnxL2tpLnsTuPppLcpKaHoldUp specifies how many LCP keepalive messages can be missed before the related session is brought down. The value zero specifies that the actual value must be used of the object tmnxL2tpLnsTgPppLcpKaHoldUp. If the value of tmnxL2tpLnsTuPppLcpKaHoldUp is equal to zero, the value of tmnxL2tpLnsTuPppLcpKaInterval must also be equal to zero.
TMN tmnxL2tpLnsTuPppIpcpSubnetNeg	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.13	TmnxAlwaysNeverOrDefault	read-create	The value of tmnxL2tpLnsTuPppIpcpSubnetNeg specifies if IPCP subnet negotiation is enabled.
tmnxL2tpTuMlpppTable	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4		not-accessible	The L2TP Tunnel configuration table contains objects to configure MLPPP on L2TP Tunnels. Entries in this table are automatically created and deleted by the system.
tmnxL2tpTuMlpppEntry	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1		not-accessible	Each conceptual row represents MLPPP information about a Layer Two Tunneling Protocol LNS Tunnel configuration.
TIM tmnxL2tpTuMlpppLastMgmtChange	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.1	TimeStamp	read-only	The value of tmnxL2tpTuMlpppLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
TMN tmnxL2tpTuMlpppAdminState	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.2	TmnxAdminState	read-create	The value of tmnxL2tpTuMlpppAdminState specifies the administrative state of MLPPP for this Layer Two Tunneling Protocol Tunnel. The value 'noop' specifies that the actual value must be used of the object tmnxL2tpTgMlpppAdminState of the tunnel group this tunnel configuration belongs to.
U32 tmnxL2tpTuMlpppMaxLinks	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.3	Unsigned32	read-create	The value of the object tmnxL2tpTuMlpppMaxLinks specifies the maximum number of MLPPP links. The value of this object is only relevant for tunnels where this system performs the LNS role. The value zero specifies that the actual value must be used of the object tmnxL2tpTgMlpppMaxLinks of the tunnel group this tunnel configuration belongs to.
TMN tmnxL2tpTuMlpppInterleave	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.4	TmnxAlwaysNeverOrDefault	read-create	The value of tmnxL2tpTuMlpppInterleave specifies if this system applies Link Fragmentation and Interleaving to the traffic sent from the LNS to the LAC. If the value of this object is 'always', downstream traffic is fragmented and interleaved, meaning that (non-fragmented) realtime traffic is interleaved with fragments of non-realtime traffic. If the value of this object is 'never', downstream traffic is only fragmented but not reordered according to priority. The value 'default' specifies that the actual value must be used of the object tmnxL2tpTgMlpppInterleave. The value of this object is only relevant for tunnels where this system performs the LNS role.
TMN tmnxL2tpTuMlpppMaxFragDelay	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.5	TmnxL2tpMlpppMaxFragDelay	read-create	The value of tmnxL2tpTuMlpppMaxFragDelay specifies the maximum delay of fragments for this L2TP Tunnel. The value zero specifies that the actual value must be used of the object tmnxL2tpTgMlpppMaxFragDelay of the tunnel group this tunnel configuration belongs to. The value of this object is only relevant for tunnels where this system performs the LNS role.
TMN tmnxL2tpTuMlpppReassemblyTo	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.6	TmnxL2tpMlpppReassemblyTimeout	read-create	The value of tmnxL2tpTuMlpppReassemblyTo specifies the reassembly timeout for fragments for this L2TP Tunnel. The value zero specifies that the actual value must be used of the object tmnxL2tpTgMlpppReassemblyTo of the tunnel group this tunnel configuration belongs to. The value of this object is only relevant for tunnels where this system performs the LNS role.
TMN tmnxL2tpTuMlpppShortSeqNumberRx	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.7	TmnxAlwaysNeverOrDefault	read-create	The value of tmnxL2tpTuMlpppShortSeqNumberRx specifies if this system requests to receive short sequence numbers from the peer. If the value of this object is 'always', this system includes the Short Sequence Number Header Format Option in its LCP configuration options. If the value of this object is 'never', this system does not includes the Short Sequence Number Header Format Option in its LCP configuration options. The value of this object is only relevant for tunnels where this system performs the LNS role.
NUM tmnxL2tpTuMlpppEpClass	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.8	TmnxL2tpMlpppEndpointClass	read-create	The value of tmnxL2tpTuMlpppEpClass specifies the type of endpoint. If the value of 'tmnxL2tpTuMlpppEpClass' is equal to 'ipv4Address', the address for the MLPPP Endpoint Discriminator Option is taken from tmnxL2tpTuMlpppEpIpv4Address. If the value of 'tmnxL2tpTuMlpppEpClass' is equal to 'macAddress', the address for the MLPPP Endpoint Discriminator Option is taken from tmnxL2tpTuMlpppEpMacAddress. The value 'default' specifies that the actual value must be used of the object tmnxL2tpTgMlpppEpClass of the tunnel group this tunnel configuration belongs to. A value other than 'default' is only relevant for tunnels where this system performs the LNS role.
ADR tmnxL2tpTuMlpppEpIpv4Address	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.9	InetAddressIPv4	read-create	The value of tmnxL2tpTuMlpppEpIpv4Address specifies the class 2 address to use in the MLPPP Endpoint Discriminator Option. While the value of tmnxL2tpTuMlpppEpClass is equal to 'ipv4Address', a value of all zeroes specifies that the system IP address be used; otherwise, it means that no address is specified.
MAC tmnxL2tpTuMlpppEpMacAddress	1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.10	MacAddress	read-create	The value of tmnxL2tpTuMlpppEpMacAddress specifies the class 3 address to use in the MLPPP Endpoint Discriminator Option. While the value of tmnxL2tpTuMlpppEpClass is equal to 'macAddress', a value of all zeroes specifies that the system MAC address be used; otherwise, it means that no address is specified.
tmnxL2tpTuStatObjs	1.3.6.1.4.1.6527.3.1.2.60.1.3.2
tmnxL2tpTuStatusTable	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2		not-accessible	The tmnxL2tpTuStatusTable has an entry for each Layer Two Tunneling Protocol Tunnel.
tmnxL2tpTuStatusEntry	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1		not-accessible	Each conceptual row represents a Layer Two Tunneling Protocol Tunnel. Entries in this table are created and destroyed by the system.
TMN tmnxL2tpTuStatusId	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.1	TmnxL2tpConnectionId	not-accessible	The value of the object tmnxL2tpTuStatusId indicates the local identifier of this Layer Two Tunneling Protocol Tunnel. In L2TP version 2, it contains the 16-bit tunnel ID in the high-order bits. In L2TP version 3, it is the 32-bit control connection ID.
TMN tmnxL2tpTuStatusState	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.2	TmnxL2tpTuOperState	read-only	The value of tmnxL2tpTuStatusState indicates the operational state of this Layer Two Tunneling Protocol Tunnel.
TMN tmnxL2tpTuStatusTunnelId	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.3	TmnxL2tpTunnelId	read-only	The value of the object tmnxL2tpTuStatusTunnelId indicates the local identifier of this Layer Two Tunneling Protocol Tunnel, when L2TP version 2 is used. In L2TP version 3, it is equal to zero.
TMN tmnxL2tpTuStatusPreference	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.4	TmnxL2tpTunnelPreference	read-only	The value of tmnxL2tpTuStatusPreference indicates the preference of this Layer Two Tunneling Protocol Tunnel. The value '0' corresponds to the highest preference.
IPt tmnxL2tpTuStatusPeerAddrType	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.5	InetAddressType	read-only	The value of tmnxL2tpTuStatusPeerAddrType indicates the address type of tmnxL2tpTuStatusPeerAddr.
IP tmnxL2tpTuStatusPeerAddr	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.6	InetAddress	read-only	The value of tmnxL2tpTuStatusPeerAddr indicates the IP address of the peer.
IPt tmnxL2tpTuStatusAddrType	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.7	InetAddressType	read-only	The value of tmnxL2tpTuStatusAddrType indicates the address type of tmnxL2tpTuStatusAddr.
IP tmnxL2tpTuStatusAddr	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.8	InetAddress	read-only	The value of tmnxL2tpTuStatusAddr indicates the local IP address of this Layer Two Tunneling Protocol Tunnel.
TMN tmnxL2tpTuStatusLocalName	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.9	TmnxL2tpHostNameOrEmpty	read-only	The value of the object tmnxL2tpTuStatusLocalName indicates the host name used by this system during the authentication phase of tunnel establishment. This object is related to the RADIUS attribute Tunnel-Client-Auth-ID. It can be used to distinguish tunnels.
TMN tmnxL2tpTuStatusRemoteName	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.10	TmnxL2tpHostNameOrEmpty	read-only	The value of the object tmnxL2tpTuStatusRemoteName indicates a string that is compared to the host name used by the tunnel peer during the authentication phase of tunnel establishment. This object is related to the RADIUS attribute Tunnel-Server-Auth-ID. It can be used to distinguish tunnels.
TMN tmnxL2tpTuStatusAssignmentId	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.11	TmnxL2tpTunnelNameOrEmpty	read-only	The value of the object tmnxL2tpTuStatusAssignmentId indicates a string that distinguishes this Layer Two Tunneling Protocol Tunnel. This object is related to the RADIUS attribute Tunnel-Assignment-ID. If this tunnel corresponds to an entry in the tmnxL2tpTuCfgTable, the value of this object is equal to the value of the object tmnxL2tpTuCfgName.
NUM tmnxL2tpTuStatusHelloInterval	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.13	TmnxL2tpTunnelHelloInterval	read-only	The value of tmnxL2tpTuStatusHelloInterval indicates the time interval between two consecutive tunnel Hello messages. A value of '-1' indicates that the keepalive function is disabled.
TMN tmnxL2tpTuStatusIdleTO	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.14	TmnxL2tpTunnelIdleTO	read-only	The value of tmnxL2tpTuStatusIdleTO indicates the period of time that this Layer Two Tunneling Protocol Tunnel will persist while it has no active sessions before being disconnected. A value of -1 indicates that the tunnel will not be disconnected when it has no more active sessions.
TMN tmnxL2tpTuStatusDestructTO	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.15	TmnxL2tpTunnelDestructTO	read-only	The value of tmnxL2tpTuStatusIdleTO indicates the period of time that data of this Layer Two Tunneling Protocol Tunnel will persist after it is disconnected.
TMN tmnxL2tpTuStatusMaxRetxEstab	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.16	TmnxL2tpTunnelMaxRetx	read-only	The value of tmnxL2tpTuStatusMaxRetxEstab indicates the number of retries allowed for this Layer Two Tunneling Protocol Tunnel while it is established, before its control connection goes down.
TMN tmnxL2tpTuStatusMaxRetxNotEstab	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.17	TmnxL2tpTunnelMaxRetx	read-only	The value of tmnxL2tpTuStatusMaxRetxNotEstab indicates the number of retries allowed for this Layer Two Tunneling Protocol Tunnel while it is unestablished, before its control connection goes down.
TMN tmnxL2tpTuStatusSessionLimit	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.18	TmnxL2tpTunnelSessionLimit	read-only	The value of tmnxL2tpTuStatusSessionLimit indicates the maximum number of sessions allowed in this Layer Two Tunneling Protocol Tunnel.
TMN tmnxL2tpTuStatusAvpHiding	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.19	TmnxL2tpAvpHidingMode	read-only	The value of tmnxL2tpTuStatusAvpHiding indicates when the H bit in the header of each Attribute Value Pair (AVP) is set for the L2TP control messages related to this Layer Two Tunneling Protocol Tunnel.
TMN tmnxL2tpTuStatusGroupName	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.20	TmnxL2tpTunnelGroupNameOrEmpty	read-only	The value of tmnxL2tpTuStatusGroupName indicates the name of the tunnel group where this Layer Two Tunneling Protocol Tunnel belongs to.
TMN tmnxL2tpTuStatusRemoteTunnelId	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.21	TmnxL2tpTunnelId	read-only	The value of the object tmnxL2tpTuStatusRemoteTunnelId indicates the identifier of this Layer Two Tunneling Protocol Tunnel used by the tunnel peer, when L2TP version 2 is used. In L2TP version 3, it is equal to zero.
TMN tmnxL2tpTuStatusRemoteConnId	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.22	TmnxL2tpConnectionId	read-only	The value of the object tmnxL2tpTuStatusRemoteConnId indicates the identifier of this Layer Two Tunneling Protocol Tunnel used by the tunnel peer.
TMN tmnxL2tpTuStatusTransportType	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.23	TmnxL2tpTransportType	read-only	The value of the object tmnxL2tpTuStatusTransportType indicates the transport type used for the messages of this Layer Two Tunneling Protocol Tunnel.
INE tmnxL2tpTuStatusUdpPort	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.24	InetPortNumber	read-only	The value of tmnxL2tpTuStatusAddr indicates the local UDP port of this Layer Two Tunneling Protocol Tunnel.
INE tmnxL2tpTuStatusRemoteUdpPort	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.25	InetPortNumber	read-only	The value of the object tmnxL2tpTuStatusRemoteUdpPort indicates the UDP port of this Layer Two Tunneling Protocol Tunnel used by the tunnel peer.
TIM tmnxL2tpTuStatusStartTime	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.26	TimeStamp	read-only	The value of the object tmnxL2tpTuStatusStartTime indicates the value of sysUpTime when this Layer Two Tunneling Protocol Tunnel entered either the state 'waitReply' or 'waitConn'.
TIM tmnxL2tpTuStatusEstabTime	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.27	TimeStamp	read-only	The value of the object tmnxL2tpTuStatusEstabTime indicates the value of sysUpTime when this Layer Two Tunneling Protocol Tunnel entered the state 'established'. The value zero means that this tunnel has not been established yet.
TIM tmnxL2tpTuStatusIdleTime	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.28	TimeStamp	read-only	The value of the object tmnxL2tpTuStatusIdleTime indicates the value of sysUpTime when this Layer Two Tunneling Protocol Tunnel entered the state 'idle'. The value zero means that this tunnel has not become idle yet.
TIM tmnxL2tpTuStatusClosedTime	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.29	TimeStamp	read-only	The value of the object tmnxL2tpTuStatusClosedTime indicates the value of sysUpTime when this Layer Two Tunneling Protocol Tunnel entered one of the closed states. The value zero means that this tunnel has not been closed yet.
TMN tmnxL2tpTuStatusStopCcnResult	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.30	TmnxL2tpStopCcnResult	read-only	The value of tmnxL2tpTuStatusStopCcnResult indicates the result of a StopCCN (Stop-Control-Connection-Notification) message related to this Layer Two Tunneling Protocol Tunnel.
TMN tmnxL2tpTuStatusGeneralError	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.31	TmnxL2tpGeneralError	read-only	The value of tmnxL2tpTuStatusGeneralError indicates an general error related to this Layer Two Tunneling Protocol Tunnel.
TMN tmnxL2tpTuStatusErrorMessage	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.32	TmnxL2tpErrorMessage	read-only	The value of the object tmnxL2tpTuStatusErrorMessage indicates describes an error related to this Layer Two Tunneling Protocol Tunnel.
TMN tmnxL2tpTuStatusDoChallenge	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.33	TmnxL2tpDoChallenge	read-only	The value of tmnxL2tpTuStatusDoChallenge indicates when challenge-response is used for the authentication of this Layer Two Tunneling Protocol Tunnel.
U32 tmnxL2tpTuStatusRws	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.34	Unsigned32	read-only	The value of tmnxL2tpTuStatusRws indicates the actual Receive Window Size of this Layer Two Tunneling Protocol Tunnel.
IPt tmnxL2tpTuStatusTxDestAddrType	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.35	InetAddressType	read-only	The value of tmnxL2tpTuStatusTxDestAddrType indicates the address type of tmnxL2tpTuStatusTxDestAddr.
IP tmnxL2tpTuStatusTxDestAddr	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.36	InetAddress	read-only	The value of tmnxL2tpTuStatusTxDestAddr indicates the destination IP address used while transmitting L2TP control messages for this Layer Two Tunneling Protocol Tunnel. The destination address can be different from the value of the object tmnxL2tpTuStatusPeerAddr in case the value of the object tmnxL2tpPeerAddrChangePlcy is equal to 'accept'.
IPt tmnxL2tpTuStatusRxSrcAddrType	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.37	InetAddressType	read-only	The value of tmnxL2tpTuStatusRxSrcAddrType indicates the address type of tmnxL2tpTuStatusRxSrcAddr.
IP tmnxL2tpTuStatusRxSrcAddr	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.38	InetAddress	read-only	The value of tmnxL2tpTuStatusRxSrcAddr indicates the source IP address found in L2TP control messages received for this Layer Two Tunneling Protocol Tunnel. The source address can be different from the value of the object tmnxL2tpTuStatusAddr in case the value of the object tmnxL2tpPeerAddrChangePlcy is equal to 'accept' or 'ignore'.
TNA tmnxL2tpTuStatusAccountingPolicy	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.40	TNamedItemOrEmpty	read-only	The value of tmnxL2tpTuStatusAccountingPolicy indicates the RADIUS accounting policy of this Layer Two Tunneling Protocol Tunnel.
tmnxL2tpTuStatsTable	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3		not-accessible	The tmnxL2tpTuStatsTable has an entry for each Layer Two Tunneling Protocol Tunnel.
tmnxL2tpTuStatsEntry	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1		not-accessible	Each conceptual row represents statistics information of a Layer Two Tunneling Protocol Tunnel. Entries in this table are created and destroyed by the system.
TIM tmnxL2tpTuStatsLastCleared	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.1	TimeStamp	read-only	The value of the object tmnxL2tpTuStatsLastCleared indicates the value of sysUpTime when the contents of this conceptual row were cleared for the last time. The value zero means that the contents of this conceptual row have not yet been cleared.
C32 tmnxL2tpTuStatsTotalSessions	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.2	Counter32	read-only	The value of tmnxL2tpTuStatsTotalSessions indicates the number of session creation attempts in this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpTuStatsFailedSessions	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.3	Counter32	read-only	The value of tmnxL2tpTuStatsFailedSessions indicates the number of sessions in this tunnel that failed to reach the established state since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
G32 tmnxL2tpTuStatsActiveSessions	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.4	Gauge32	read-only	The value of tmnxL2tpTuStatsActiveSessions indicates the number of sessions currently established in this tunnel.
G32 tmnxL2tpTuStatsSessions	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.5	Gauge32	read-only	The value of tmnxL2tpTuStatsSessions indicates the actual number of sessions in this tunnel.
C64 tmnxL2tpTuStatsControlRxOctets	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.6	Counter64	read-only	The value of tmnxL2tpTuStatsControlRxOctets indicates the number of control channel octets received in this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpTuStatsControlRxOctetsLw	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.7	Counter32	read-only	The value of tmnxL2tpTuStatsControlRxOctetsLw indicates the lower 32-bits word of the value of tmnxL2tpTuStatsControlRxOctets.
C32 tmnxL2tpTuStatsControlRxOctetsHw	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.8	Counter32	read-only	The value of tmnxL2tpTuStatsControlRxOctetsHw indicates the higher 32-bits word of the value of tmnxL2tpTuStatsControlRxOctets.
C32 tmnxL2tpTuStatsControlRxPkts	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.9	Counter32	read-only	The value of tmnxL2tpTuStatsControlRxPkts indicates the number of control packets received by this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C64 tmnxL2tpTuStatsControlTxOctets	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.10	Counter64	read-only	The value of tmnxL2tpTuStatsControlTxOctets indicates the number of control channel octets that were transmitted to the current tunnel endpoints in this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpTuStatsControlTxOctetsLw	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.11	Counter32	read-only	The value of tmnxL2tpTuStatsControlTxOctetsLw indicates the lower 32-bits word of the value of tmnxL2tpTuStatsControlTxOctets.
C32 tmnxL2tpTuStatsControlTxOctetsHw	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.12	Counter32	read-only	The value of tmnxL2tpTuStatsControlTxOctetsHw indicates the higher 32-bits word of the value of tmnxL2tpTuStatsControlTxOctets.
C32 tmnxL2tpTuStatsControlTxPkts	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.13	Counter32	read-only	The value of tmnxL2tpTuStatsControlTxOctets indicates the number of control packets that were transmitted to the current tunnel endpoints in this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpTuStatsErrorTxPkts	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.14	Counter32	read-only	The value of tmnxL2tpTuStatsErrorTxPkts indicates the number of packet transmission errors on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpTuStatsErrorRxPkts	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.15	Counter32	read-only	The value of tmnxL2tpTuStatsErrorRxPkts indicates the number of errored packets that were received on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpTuStatsFsmMsgAccepted	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.16	Counter32	read-only	The value of tmnxL2tpTuStatsFsmMsgAccepted indicates the number of Finite State Machine (FSM) messages that were accepted on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpTuStatsFsmMsgDuplicateRx	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.17	Counter32	read-only	The value of tmnxL2tpTuStatsFsmMsgDuplicateRx indicates the number of Finite State Machine (FSM) duplicate messages that were received on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpTuStatsFsmMsgOutOfWndwRx	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.18	Counter32	read-only	The value of tmnxL2tpTuStatsFsmMsgOutOfWndwRx indicates the number of Finite State Machine (FSM) messages that were received out of the receive window on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
G32 tmnxL2tpTuStatsQLengthUnsentMax	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.19	Gauge32	read-only	The value of tmnxL2tpTuStatsQLengthUnsentMax indicates the the maximum length of the unsent message queue on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
G32 tmnxL2tpTuStatsQLengthUnsentCur	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.20	Gauge32	read-only	The value of tmnxL2tpTuStatsErrorRxPkts indicates the the current length of the unsent message queue on this tunnel.
G32 tmnxL2tpTuStatsQLengthAckMax	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.21	Gauge32	read-only	The value of tmnxL2tpTuStatsErrorRxPkts indicates the the maximum length of the acknowledged message queue on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
G32 tmnxL2tpTuStatsQLengthAckCur	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.22	Gauge32	read-only	The value of tmnxL2tpTuStatsErrorRxPkts indicates the the current length of the acknowledged message queue on this tunnel.
G32 tmnxL2tpTuStatsWindowSizeCur	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.23	Gauge32	read-only	The value of tmnxL2tpTuStatsErrorRxPkts indicates the the current size of the receive window on this tunnel.
tmnxL2tpTuProtStatsTable	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.4		not-accessible	The tmnxL2tpTuProtStatsTable shows protocol statistics information of Layer Two Tunneling Protocol Tunnels.
tmnxL2tpTuProtStatsEntry	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.4.1		not-accessible	Each conceptual row represents protocol statistics of a specific type. Entries in this table are created and destroyed by the system. Rows are only created where the statistics value is nonzero; this allows faster walking through this table; hence, it is recommended to perform only get-next-request operations to retrieve information from this table.
TMN tmnxL2tpTuProtStatsType	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.4.1.1	TmnxL2tpTuProtStatsType	not-accessible	The value of the object tmnxL2tpTuProtStatsType indicates the type of L2TP protocol statistics contained in this conceptual row.
U32 tmnxL2tpTuProtStatsInstance	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.4.1.2	Unsigned32	not-accessible	The value of the object tmnxL2tpTuProtStatsType indicates the instance identifier of the statistics contained in this conceptual row. For example: if the value of the object tmnxL2tpTuProtStatsType is equal to 'outgoingMsgType', the value of tmnxL2tpTuProtStatsInstance is a message identifier, e.g. instance '2' refers to '(SCCRP) Start-Control-Connection-Reply', and the value of tmnxL2tpTuProtStatsVal indicates the number of SCCRP messages transmitted for this tunnel. Unknown protocol messages are counted with instance zero.
STR tmnxL2tpTuProtStatsName	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.4.1.3	DisplayString	read-only	The value of the object tmnxL2tpTuProtStatsType indicates the human-readable identifier of the statistics contained in this conceptual row. In the same example, the value of tmnxL2tpTuProtStatsName is '(SCCRP) Start-Control-Connection-Reply'.
C32 tmnxL2tpTuProtStatsVal	1.3.6.1.4.1.6527.3.1.2.60.1.3.2.4.1.4	Counter32	read-only	The value of the object tmnxL2tpTuProtStatsType indicates the value of the statistics contained in this conceptual row.
tmnxL2tpTuOpObjs	1.3.6.1.4.1.6527.3.1.2.60.1.3.3
tmnxL2tpTuStartTable	1.3.6.1.4.1.6527.3.1.2.60.1.3.3.1		not-accessible	The tmnxL2tpTuStartTable has an entry for each Layer Two Tunneling Protocol Tunnel.
tmnxL2tpTuStartEntry	1.3.6.1.4.1.6527.3.1.2.60.1.3.3.1.1		not-accessible	Each conceptual row presents an operations interface to start a Layer Two Tunneling Protocol Tunnel control connection. Entries in this table are created and destroyed by the system.
TMN tmnxL2tpTuStart	1.3.6.1.4.1.6527.3.1.2.60.1.3.3.1.1.1	TmnxActionType	read-write	Setting this object to 'doAction (1)' triggers an attempt to start the control connection for this L2TP tunnel. Reading this object returns the value 'notApplicable'.
tmnxL2tpTuStopTable	1.3.6.1.4.1.6527.3.1.2.60.1.3.3.2		not-accessible	The tmnxL2tpTuStopTable has an entry for each active Layer Two Tunneling Protocol Tunnel.
tmnxL2tpTuStopEntry	1.3.6.1.4.1.6527.3.1.2.60.1.3.3.2.1		not-accessible	Each conceptual row presents an operations interface to stop a Layer Two Tunneling Protocol Tunnel control connection. Entries in this table are created and destroyed by the system.
TMN tmnxL2tpTuStop	1.3.6.1.4.1.6527.3.1.2.60.1.3.3.2.1.1	TmnxActionType	read-write	Setting this object to 'doAction (1)' triggers an attempt to stop the control connection for this L2TP tunnel. Reading this object returns the value 'notApplicable'.
tmnxL2tpTuDrainTable	1.3.6.1.4.1.6527.3.1.2.60.1.3.3.3		not-accessible	The tmnxL2tpTuDrainTable has an entry for each active Layer Two Tunneling Protocol Tunnel.
tmnxL2tpTuDrainEntry	1.3.6.1.4.1.6527.3.1.2.60.1.3.3.3.1		not-accessible	Each conceptual row presents an operations interface to drain a Layer Two Tunneling Protocol Tunnel. After a successful drain operation, the value of the object tmnxL2tpTuStatusState of this tunnel is equal to 'draining'; this tunnel does not accept or establish new connections, while existing connections are timing out. Entries in this table are created and destroyed by the system.
TMN tmnxL2tpTuDrain	1.3.6.1.4.1.6527.3.1.2.60.1.3.3.3.1.1	TmnxL2tpActionTypeDrain	read-write	Setting this object to 'drain (0)' triggers an attempt to drain this L2TP tunnel. Setting it to 'stopDrain (1)' stops the draining. Reading this object returns the value 'notApplicable'.
tmnxL2tpPeerObjs	1.3.6.1.4.1.6527.3.1.2.60.1.4
tmnxL2tpPeerStatObjs	1.3.6.1.4.1.6527.3.1.2.60.1.4.1
tmnxL2tpPeerStatTable	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1		not-accessible	The tmnxL2tpPeerStatTable contains status and statistics information about L2TP peers.
tmnxL2tpPeerStatEntry	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1		not-accessible	Each row entry represents status and statistics information about a particular L2TP peer. Rows are created or removed automatically by the system.
INT tmnxL2tpPeerStatRole	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.1	INTEGER	read-only	The value of tmnxL2tpPeerStatRole indicates the role of this system in relation to the peer.
G32 tmnxL2tpPeerStatActiveTunnels	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.2	Gauge32	read-only	The value of tmnxL2tpPeerStatActiveTunnels indicates the number of tunnels associated with this peer that are currently established.
G32 tmnxL2tpPeerStatTunnels	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.3	Gauge32	read-only	The value of tmnxL2tpPeerStatTunnels indicates the actual number of tunnels associated with this peer.
G32 tmnxL2tpPeerStatActiveSessions	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.4	Gauge32	read-only	The value of tmnxL2tpPeerStatActiveSessions indicates the number of sessions associated with this peer that are currently established.
G32 tmnxL2tpPeerStatSessions	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.5	Gauge32	read-only	The value of tmnxL2tpPeerStatSessions indicates the actual number of sessions associated with this peer.
T/F tmnxL2tpPeerStatDraining	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.6	TruthValue	read-only	The value of tmnxL2tpPeerStatDraining indicates if this peer is being drained.
T/F tmnxL2tpPeerStatUnreachable	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.7	TruthValue	read-only	The value of tmnxL2tpPeerStatUnreachable indicates if this peer is deemed unreachable.
TIM tmnxL2tpPeerStatUnreachableTime	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.8	TimeStamp	read-only	The value of the object tmnxL2tpPeerStatUnreachableTime indicates the value of sysUpTime when the this peer was deemed unreachable for the last time. The value zero means that this peer has not been deemed unreachable yet.
C64 tmnxL2tpPeerStatControlRxOct	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.9	Counter64	read-only	The value of tmnxL2tpPeerStatControlRxOct indicates the number of control channel octets received in this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpPeerStatControlRxOctLw	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.10	Counter32	read-only	The value of tmnxL2tpPeerStatControlRxOctLw indicates the lower 32-bits word of the value of tmnxL2tpPeerStatControlRxOct.
C32 tmnxL2tpPeerStatControlRxOctHw	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.11	Counter32	read-only	The value of tmnxL2tpPeerStatControlRxOctHw indicates the higher 32-bits word of the value of tmnxL2tpPeerStatControlRxOct.
C32 tmnxL2tpPeerStatControlRxPkts	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.12	Counter32	read-only	The value of tmnxL2tpPeerStatControlRxPkts indicates the number of control packets received by this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C64 tmnxL2tpPeerStatControlTxOct	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.13	Counter64	read-only	The value of tmnxL2tpPeerStatControlTxOct indicates the number of control channel octets that were transmitted to the current tunnel endpoints in this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpPeerStatControlTxOctLw	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.14	Counter32	read-only	The value of tmnxL2tpPeerStatControlTxOctLw indicates the lower 32-bits word of the value of tmnxL2tpPeerStatControlTxOct.
C32 tmnxL2tpPeerStatControlTxOctHw	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.15	Counter32	read-only	The value of tmnxL2tpPeerStatControlTxOctHw indicates the higher 32-bits word of the value of tmnxL2tpPeerStatControlTxOct.
C32 tmnxL2tpPeerStatControlTxPkts	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.16	Counter32	read-only	The value of tmnxL2tpPeerStatControlTxOct indicates the number of control packets that were transmitted to the current tunnel endpoints in this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpPeerStatErrorTxPkts	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.17	Counter32	read-only	The value of tmnxL2tpPeerStatErrorTxPkts indicates the number of packet transmission errors on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpPeerStatErrorRxPkts	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.18	Counter32	read-only	The value of tmnxL2tpPeerStatErrorRxPkts indicates the number of errored packets that were received on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpPeerStatMsgAccepted	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.19	Counter32	read-only	The value of tmnxL2tpPeerStatMsgAccepted indicates the number of Finite State Machine (FSM) messages that were accepted from this peer since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpPeerStatMsgDuplicateRx	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.20	Counter32	read-only	The value of tmnxL2tpPeerStatMsgDuplicateRx indicates the number of Finite State Machine (FSM) duplicate messages that were received from this peer since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
C32 tmnxL2tpPeerStatMsgOutOfWndwRx	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.21	Counter32	read-only	The value of tmnxL2tpPeerStatMsgOutOfWndwRx indicates the number of Finite State Machine (FSM) messages that were received out of the receive window from this peer since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
TMN tmnxL2tpPeerStatRolesCapability	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.22	TmnxL2tpRoles	read-only	The value of tmnxL2tpPeerStatRolesCapability indicates the roles that this system could perform in relation to the peer.
TMN tmnxL2tpPeerStatRoles	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.23	TmnxL2tpRoles	read-only	The value of tmnxL2tpPeerStatRole indicates the actual roles of this system in relation to the peer.
TIM tmnxL2tpPeerStatLastCleared	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.99	TimeStamp	read-only	The value of the object tmnxL2tpPeerStatLastCleared indicates the value of sysUpTime when the contents of this conceptual row were cleared for the last time. The value zero means that the contents of this conceptual row have not yet been cleared.
tmnxL2tpPeerTuTable	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.2		not-accessible	The tmnxL2tpPeerTuTable contains the set of active tunnels for each L2TP peer.
tmnxL2tpPeerTuEntry	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.2.1		not-accessible	Each row entry contains a tunnel identifier of an L2TP peer. Rows are created or removed automatically by the system. Note that all L2TP peers appear in this table with remote UDP port equal to 1701, regardless of the actual port in use.
TMN tmnxL2tpPeerTuId	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.2.1.1	TmnxL2tpConnectionId	read-only	The value of the object tmnxL2tpPeerTuId indicates the local identifier of a Layer Two Tunneling Protocol Tunnel.
tmnxL2tpPeerProtStatsTable	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3		not-accessible	The tmnxL2tpPeerProtStatsTable contains protocol statistics information about L2TP peers.
tmnxL2tpPeerProtStatsEntry	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1		not-accessible	Each conceptual row represents protocol statistics of a specific type for a specific L2TP peer. Entries in this table are created and destroyed by the system. Rows are only created where the statistics value is nonzero; this allows faster walking through this table; hence, it is recommended to perform only get-next-request operations to retrieve information from this table.
TMN tmnxL2tpPeerProtStatsTransport	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.1	TmnxL2tpTransportType	not-accessible	The value of the object tmnxL2tpTuStatusTransportType indicates the transport type used for the messages to this L2TP peer.
IPt tmnxL2tpPeerProtStatsAddrType	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.2	InetAddressType	not-accessible	The value of tmnxL2tpPeerProtStatsAddrType indicates the address type of tmnxL2tpPeerProtStatsAddr.
IP tmnxL2tpPeerProtStatsAddr	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.3	InetAddress	not-accessible	The value of tmnxL2tpPeerProtStatsAddr indicates the IP address of the peer.
INE tmnxL2tpPeerProtStatsRemUdpPort	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.4	InetPortNumber	not-accessible	The value of the object tmnxL2tpPeerProtStatsRemUdpPort indicates the UDP port used by the tunnel peer.
TMN tmnxL2tpPeerProtStatsType	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.5	TmnxL2tpTuProtStatsType	not-accessible	The value of the object tmnxL2tpPeerProtStatsType indicates the type of L2TP protocol statistics contained in this conceptual row.
U32 tmnxL2tpPeerProtStatsInstance	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.6	Unsigned32	not-accessible	The value of the object tmnxL2tpPeerProtStatsInstance indicates the instance identifier of the statistics contained in this conceptual row. For example: if the value of the object tmnxL2tpPeerProtStatsType is equal to 'outgoingMsgType', the value of tmnxL2tpPeerProtStatsInstance is a message identifier, e.g. instance '2' refers to '(SCCRP) Start-Control-Connection-Reply', and the value of tmnxL2tpPeerProtStatsVal indicates the number of SCCRP messages transmitted for this tunnel. Unknown protocol messages are counted with instance zero.
STR tmnxL2tpPeerProtStatsName	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.7	DisplayString	read-only	The value of the object tmnxL2tpPeerProtStatsName indicates the human-readable identifier of the statistics contained in this conceptual row. In the same example, the value of tmnxL2tpPeerProtStatsName is '(SCCRP) Start-Control-Connection-Reply'.
C32 tmnxL2tpPeerProtStatsVal	1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.8	Counter32	read-only	The value of the object tmnxL2tpPeerProtStatsVal indicates the value of the statistics contained in this conceptual row.
tmnxL2tpPeerOpObjs	1.3.6.1.4.1.6527.3.1.2.60.1.4.2
tmnxL2tpPeerDrainTable	1.3.6.1.4.1.6527.3.1.2.60.1.4.2.1		not-accessible	The tmnxL2tpPeerDrainTable has an entry for each L2TP peer. Note that all L2TP peers appear in this table with remote UDP port equal to 1701, regardless of the actual port in use.
tmnxL2tpPeerDrainEntry	1.3.6.1.4.1.6527.3.1.2.60.1.4.2.1.1		not-accessible	Each row entry presents an operations interface to drain all tunnels between this system and a particular L2TP peer. Rows are created or removed automatically by the system.
TMN tmnxL2tpPeerDrain	1.3.6.1.4.1.6527.3.1.2.60.1.4.2.1.1.1	TmnxL2tpActionTypeDrain	read-write	Setting this object to 'drain (0)' triggers an attempt to drain all tunnels between this system and a particular L2TP peer. Setting it to 'stopDrain (1)' stops the draining. Reading this object returns the value 'notApplicable'.
tmnxL2tpSessionObjs	1.3.6.1.4.1.6527.3.1.2.60.1.5
tmnxL2tpSeStatObjs	1.3.6.1.4.1.6527.3.1.2.60.1.5.1
tmnxL2tpSeStatusTable	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1		not-accessible	The tmnxL2tpSeStatusTable has an entry for each Layer Two Tunneling Protocol Session.
tmnxL2tpSeStatusEntry	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1		not-accessible	Each conceptual row represents a Layer Two Tunneling Protocol Session. Entries in this table are created and destroyed by the system.
TMN tmnxL2tpSeStatusId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.1	TmnxL2tpConnectionId	not-accessible	The value of the object tmnxL2tpSeStatusId indicates the local identifier of this Layer Two Tunneling Protocol Session. In L2TP version 2, it contains the 16-bit session ID in the lower order bits and the 16-bit tunnel ID in the higher order bits. In L2TP version 3, it is the 32-bit session ID.
TMN tmnxL2tpSeStatusState	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.2	TmnxL2tpSeOperState	read-only	The value of tmnxL2tpSeStatusState indicates the operational state of this Layer Two Tunneling Protocol Session.
TMN tmnxL2tpSeStatusTunnelId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.3	TmnxL2tpTunnelId	read-only	The value of the object tmnxL2tpSeStatusTunnelId indicates the identifier of the L2TP tunnel associated with this Layer Two Tunneling Protocol Session, when L2TP version 2 is used. In L2TP version 3, it is equal to zero.
TMN tmnxL2tpSeStatusTunnelConnId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.4	TmnxL2tpConnectionId	read-only	The value of the object tmnxL2tpSeStatusTunnelConnId indicates the identifier of the L2TP tunnel associated with this Layer Two Tunneling Protocol Session.
TMN tmnxL2tpSeStatusSessionId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.5	TmnxL2tpSessionId	read-only	The value of the object tmnxL2tpSeStatusSessionId indicates the identifier of this Layer Two Tunneling Protocol Session, when L2TP version 2 is used. In L2TP version 3, it is equal to zero.
TMN tmnxL2tpSeStatusRemoteTunnelId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.6	TmnxL2tpTunnelId	read-only	The value of the object tmnxL2tpSeStatusRemoteTunnelId indicates the identifier used by the tunnel peer of the L2TP tunnel associated with this Layer Two Tunneling Protocol Session , when L2TP version 2 is used. In L2TP version 3, it is equal to zero.
TMN tmnxL2tpSeStatusRemoteSessionId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.7	TmnxL2tpSessionId	read-only	The value of the object tmnxL2tpSeStatusRemoteSessionId indicates the identifier of this Layer Two Tunneling Protocol Session used by the tunnel peer, when L2TP version 2 is used. In L2TP version 3, it is equal to zero.
TMN tmnxL2tpSeStatusRemoteConnId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.8	TmnxL2tpConnectionId	read-only	The value of the object tmnxL2tpSeStatusRemoteConnId indicates the identifier of this Layer Two Tunneling Protocol Session used by the tunnel peer.
TIM tmnxL2tpSeStatusStartTime	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.9	TimeStamp	read-only	The value of the object tmnxL2tpSeStatusStartTime indicates the value of sysUpTime when this Layer Two Tunneling Protocol Session entered either the state 'idle', 'waitTunnel', 'waitReply' or 'waitAcceptance'.
TIM tmnxL2tpSeStatusEstabTime	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.10	TimeStamp	read-only	The value of the object tmnxL2tpSeStatusEstabTime indicates the value of sysUpTime when this Layer Two Tunneling Protocol Session entered the state 'established'. The value zero means that this session has not been established yet.
TIM tmnxL2tpSeStatusClosedTime	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.11	TimeStamp	read-only	The value of the object tmnxL2tpSeStatusClosedTime indicates the value of sysUpTime when this Layer Two Tunneling Protocol Session entered one of the closed states. The value zero means that this session has not been closed yet.
TMN tmnxL2tpSeStatusCdnResult	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.12	TmnxL2tpCdnResult	read-only	The value of tmnxL2tpSeStatusCdnResult indicates the result of a CDN (Call-Disconnect-Notify) message related to this Layer Two Tunneling Protocol Session.
TMN tmnxL2tpSeStatusGeneralError	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.13	TmnxL2tpGeneralError	read-only	The value of tmnxL2tpSeStatusGeneralError indicates an general error related to this Layer Two Tunneling Protocol Session.
TMN tmnxL2tpSeStatusErrorMessage	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.14	TmnxL2tpErrorMessage	read-only	The value of the object tmnxL2tpSeStatusErrorMessage describes an error related to this Layer Two Tunneling Protocol Session.
U32 tmnxL2tpSeStatusMlpppBundleIndex	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.20	Unsigned32	read-only	The value of the object tmnxL2tpSeStatusMlpppBundleIndex indicates the identifier of the MLPPP Bundle related to this Layer Two Tunneling Protocol Session. If an MLPPP bundle is associated with this session, the value of tmnxL2tpSeStatusMlpppBundleIndex is equal to the value of tmnxL2tpLacMlpppBundleIndex of the corresponding row in the tmnxL2tpLacMlpppBundleTable, in the same virtual router instance. If no MLPPP bundle is associated with this session, the value of this object is equal to zero.
tmnxL2tpLnsSePppTable	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2		not-accessible	The tmnxL2tpLnsSePppTable has an entry for each Layer Two Tunneling Protocol Session for which this system acts as LNS.
tmnxL2tpLnsSePppEntry	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1		not-accessible	Each conceptual row represents a Layer Two Tunneling Protocol Session. Entries in this table are created and destroyed by the system. In release 9.0 and higher, this information is in the SUBSCRIBER-MGMT-MIB::tmnxSubPppTable. The corresponding row in that table can be directly retrieved using the value of the object tmnxL2tpLnsSePppSubPppIndex.
TIK tmnxL2tpLnsSePppUpTime	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.3	TimeTicks	read-only	The value of tmnxL2tpLnsSePppUpTime indicates how long (in hundredths of a second) that the session already exists in this table.
TMN tmnxL2tpLnsSePppLcpState	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.4	TmnxPppCpState	read-only	The value of tmnxL2tpLnsSePppLcpState indicates the current state of the PPP Link Control Protocol of the session.
TMN tmnxL2tpLnsSePppIpcpState	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.5	TmnxPppCpState	read-only	The value of tmnxL2tpLnsSePppIpcpState indicates the current state of the PPP IP Control Protocol of the session.
U32 tmnxL2tpLnsSePppPppMtu	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.6	Unsigned32	read-only	The value of tmnxL2tpLnsSePppPppMtu indicates the PPP MTU of the session.
INT tmnxL2tpLnsSePppPppAuthProtocol	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.7	INTEGER	read-only	The value of tmnxL2tpLnsSePppPppAuthProtocol indicates the PPP protocol used to authenticate the session. The value 'none' indicates that no PPP authentication was done. The value 'pap' indicates that authentication was done via the Password Authentication Protocol. The value 'chap' indicates that authentication was done via the Challenge-Handshake Authentication Protocol.
TMN tmnxL2tpLnsSePppPppUserName	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.8	TmnxPppoeUserNameOrEmpty	read-only	The value of tmnxL2tpLnsSePppPppUserName indicates the user name learned during the PPP authentication phase.
STR tmnxL2tpLnsSePppSubIdent	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.9	TmnxSubIdentStringOrEmpty	read-only	The value of tmnxL2tpLnsSePppSubIdent indicates the subscriber applicable for this session. The value of tmnxL2tpLnsSePppOriginSubIdent indicates from what source this subscriber identification was received.
TMN tmnxL2tpLnsSePppOriginSubIdent	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.10	TmnxPppoeSessionInfoOrigin	read-only	The value of tmnxL2tpLnsSePppOriginSubIdent indicates which source provided the subscriber.
STR tmnxL2tpLnsSePppSubProfString	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.11	TmnxSubProfileStringOrEmpty	read-only	The value of tmnxL2tpLnsSePppSubProfString indicates the subscriber profile string applicable for this session. The value of tmnxL2tpLnsSePppOriginStrings indicates from what source this string was received.
STR tmnxL2tpLnsSePppSlaProfString	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.12	TmnxSlaProfileStringOrEmpty	read-only	The value of tmnxL2tpLnsSePppSlaProfString indicates the SLA profile string applicable for this session. The value of tmnxL2tpLnsSePppOriginStrings indicates from what source this string was received.
STR tmnxL2tpLnsSePppAncpString	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.13	TmnxAncpStringOrZero	read-only	The value of tmnxL2tpLnsSePppAncpString indicates the ANCP string applicable for this session. The value of tmnxL2tpLnsSePppOriginStrings indicates from what source this string was received.
NUM tmnxL2tpLnsSePppInterDestId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.14	TmnxSubMgtIntDestIdOrEmpty	read-only	The value of tmnxL2tpLnsSePppInterDestId indicates the intermediate destination identifier applicable for this session. The value of tmnxL2tpLnsSePppOriginStrings indicates from what source this string was received.
STR tmnxL2tpLnsSePppAppProfString	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.15	TmnxAppProfileStringOrEmpty	read-only	The value of tmnxL2tpLnsSePppAppProfString indicates the application profile string applicable for this session. The value of tmnxL2tpLnsSePppOriginStrings indicates from what source this string was received.
TMN tmnxL2tpLnsSePppOriginStrings	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.16	TmnxPppoeSessionInfoOrigin	read-only	The value of tmnxL2tpLnsSePppOriginStrings indicates which source provided the subscriber identification strings (subscriber profile string, SLA profile string, ANCP string, intermediate destination identifier and application profile string).
U32 tmnxL2tpLnsSePppSessionTimeout	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.17	Unsigned32	read-only	The value of tmnxL2tpLnsSePppSessionTimeout indicates the session timeout received from the Radius server (if applicable).
IPt tmnxL2tpLnsSePppIpAddrType	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.18	InetAddressType	read-only	The value of tmnxL2tpLnsSePppIpAddrType indicates the address type of tmnxL2tpLnsSePppIpAddr.
IP tmnxL2tpLnsSePppIpAddr	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.19	InetAddress	read-only	The value of tmnxL2tpLnsSePppIpAddr indicates the IP address of the session. The value of tmnxL2tpLnsSePppOriginIpcpInfo indicates from what source this IP address was received.
IPt tmnxL2tpLnsSePppPrimaryDnsType	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.20	InetAddressType	read-only	The value of tmnxL2tpLnsSePppPrimaryDnsType indicates the address type of tmnxL2tpLnsSePppPrimaryDns.
IP tmnxL2tpLnsSePppPrimaryDns	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.21	InetAddress	read-only	The value of tmnxL2tpLnsSePppPrimaryDns indicates the primary DNS server. The value of this object is ''H when not applicable. The value of tmnxL2tpLnsSePppOriginIpcpInfo indicates from what source this IP address was received.
IPt tmnxL2tpLnsSePppSecondaryDnsType	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.22	InetAddressType	read-only	The value of tmnxL2tpLnsSePppSecondaryDnsType indicates the address type of tmnxL2tpLnsSePppSecondaryDns.
IP tmnxL2tpLnsSePppSecondaryDns	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.23	InetAddress	read-only	The value of tmnxL2tpLnsSePppSecondaryDns indicates the secondary DNS server. The value of this object is ''H when not applicable. The value of tmnxL2tpLnsSePppOriginIpcpInfo indicates from what source this IP address was received.
IPt tmnxL2tpLnsSePppPrimaryNbnsType	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.24	InetAddressType	read-only	The value of tmnxL2tpLnsSePppPrimaryNbnsType indicates the address type of tmnxL2tpLnsSePppPrimaryNbns.
IP tmnxL2tpLnsSePppPrimaryNbns	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.25	InetAddress	read-only	The value of tmnxL2tpLnsSePppPrimaryNbns indicates the primary NBNS server. The value of this object is ''H when not applicable. The value of tmnxL2tpLnsSePppOriginIpcpInfo indicates from what source this IP address was received.
IPt tmnxL2tpLnsSePppSecondNbnsType	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.26	InetAddressType	read-only	The value of tmnxL2tpLnsSePppSecondNbnsType indicates the address type of tmnxL2tpLnsSePppSecondNbns.
IP tmnxL2tpLnsSePppSecondNbns	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.27	InetAddress	read-only	The value of tmnxL2tpLnsSePppSecondNbns indicates the secondary NBNS server. The value of this object is ''H when not applicable. The value of tmnxL2tpLnsSePppOriginIpcpInfo indicates from what source this IP address was received.
TMN tmnxL2tpLnsSePppOriginIpcpInfo	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.28	TmnxPppoeSessionInfoOrigin	read-only	The value of tmnxL2tpLnsSePppOriginIpcpInfo indicates which source provided the IPCP information (IP, DNS and NBNS addresses).
OCT tmnxL2tpLnsSePppCircuitId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.29	OCTET STRING	read-only	The value of tmnxL2tpLnsSePppCircuitId indicates the value of the circuit-id sub-option.
OCT tmnxL2tpLnsSePppRemoteId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.30	OCTET STRING	read-only	The value of tmnxL2tpLnsSePppRemoteId indicates the value of the remote-id sub-option.
STR tmnxL2tpLnsSePppAddressPool	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.31	DisplayString	read-only	The value of tmnxL2tpLnsSePppAddressPool indicates the IP address pool which is used to search for an IP address for this session.
TMN tmnxL2tpLnsSePppType	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.32	TmnxPppoeSessionType	read-only	The value of tmnxL2tpLnsSePppType indicates the type of this session.
TMN tmnxL2tpLnsSePppSvcId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.33	TmnxServId	read-only	The value of tmnxL2tpLnsSePppSvcId indicates the service ID of the IES/VPRN service to which this session belongs.
NUM tmnxL2tpLnsSePppGrpIf	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.34	InterfaceIndexOrZero	read-only	The value of tmnxL2tpLnsSePppGrpIf indicates the interface index of the group-interface to which this session belongs.
TMN tmnxL2tpLnsSePppL2tpVrtrId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.35	TmnxVRtrIDOrZero	read-only	The value of tmnxL2tpLnsSePppL2tpVrtrId indicates the virtual router ID of the L2TP session associated with this session. If there is no L2TP session associated with this session, the value of this object is equal to zero.
U32 tmnxL2tpLnsSePppL2tpConnectionId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.36	Unsigned32	read-only	The value of tmnxL2tpLnsSePppL2tpVrtrId indicates the connection ID of the L2TP session associated with this session. The values of tmnxL2tpLnsSePppL2tpVrtrId and tmnxL2tpLnsSePppL2tpConnectionId are the index in the table TIMETRA-L2TP-MIB::tmnxL2tpSeStatusTable of the L2TP session associated with this session. If there is no L2TP session associated with this session, the value of this object is equal to zero.
TNA tmnxL2tpLnsSePppCategoryMapName	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.37	TNamedItemOrEmpty	read-only	The value of tmnxL2tpLnsSePppCategoryMapName indicates the category map name applicable for this session. The value of tmnxL2tpLnsSePppOriginStrings indicates from what source this string was received.
OCT tmnxL2tpLnsSePppRadiusClassAttr	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.38	OCTET STRING	read-only	The value of tmnxL2tpLnsSePppRadiusClassAttr indicates the Class attribute returned by the RADIUS server in an Access-Accept message. If no RADIUS authentication is performed for this session, or RADIUS did not return this attribute, the value of this object is empty.
STR tmnxL2tpLnsSePppRadiusUserName	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.39	DisplayString	read-only	The value of tmnxL2tpLnsSePppRadiusUserName indicates the User-Name attribute returned by the RADIUS server in an Access-Accept message. If RADIUS did not return this attribute, the value of this object is equal to the User-Name attribute sent in the original Access-Request message. If no RADIUS authentication is performed for this session, the value of this object is empty.
TMN tmnxL2tpLnsSePppIpv6cpState	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.40	TmnxPppCpState	read-only	The value of tmnxL2tpLnsSePppIpv6cpState indicates the current state of the PPP IPv6 Control Protocol of the PPPoE session.
OCT tmnxL2tpLnsSePppInterfaceId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.41	OCTET STRING	read-only	The value of tmnxL2tpLnsSePppInterfaceId indicates the value of the remote-id sub-option inserted by the PPPoE intermediate agent.
TMN tmnxL2tpLnsSePppOriginIpv6cpInfo	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.42	TmnxPppoeSessionInfoOrigin	read-only	The value of tmnxL2tpLnsSePppOriginIpv6cpInfo indicates which source provided the IPCP information (IP, DNS and NBNS addresses).
IPt tmnxL2tpLnsSePppIpv6DnsType	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.43	InetAddressType	read-only	The value of tmnxL2tpLnsSePppIpv6DnsType indicates the address type of tmnxL2tpLnsSePppIpv6Dns1/2.
IP tmnxL2tpLnsSePppIpv6Dns1	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.44	InetAddress	read-only	The value of tmnxL2tpLnsSePppIpv6Dns1 indicates the primary DNS server. The value of this object is ''H when not applicable. The value of tmnxL2tpLnsSePppOriginIpv6cpInfo indicates from what source this IP address was received.
IP tmnxL2tpLnsSePppIpv6Dns2	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.45	InetAddress	read-only	The value of tmnxL2tpLnsSePppIpv6Dns2 indicates the secondary DNS server. The value of this object is ''H when not applicable. The value of tmnxL2tpLnsSePppOriginIpv6cpInfo indicates from what source this IP address was received.
IPt tmnxL2tpLnsSePppIpv6DelPfxType	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.46	InetAddressType	read-only	The value of tmnxL2tpLnsSePppIpv6DelPfxType indicates the address type of tmnxL2tpLnsSePppIpv6DelPfx.
ADR tmnxL2tpLnsSePppIpv6DelPfxLen	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.47	InetAddressPrefixLength	read-only	The value of tmnxL2tpLnsSePppIpv6DelPfxLen indicates the length of tmnxL2tpLnsSePppIpv6DelPfx.
IP tmnxL2tpLnsSePppIpv6DelPfx	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.48	InetAddress	read-only	The value of tmnxL2tpLnsSePppIpv6DelPfx indicates the IPv6 prefix used for DHCPv6 prefix delegation.
IPt tmnxL2tpLnsSePppIpv6PrefixType	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.49	InetAddressType	read-only	The value of tmnxL2tpLnsSePppIpv6PrefixType indicates the address type of tmnxL2tpLnsSePppIpv6Prefix.
ADR tmnxL2tpLnsSePppIpv6PrefixLen	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.50	InetAddressPrefixLength	read-only	The value of tmnxL2tpLnsSePppIpv6PrefixLen indicates the length of tmnxL2tpLnsSePppIpv6Prefix.
IP tmnxL2tpLnsSePppIpv6Prefix	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.51	InetAddress	read-only	The value of tmnxL2tpLnsSePppIpv6Prefix indicates the IPv6 prefix used for stateless address autoconfiguration.
U32 tmnxL2tpLnsSePppSubPppIndex	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.52	Unsigned32	read-only	The value of tmnxL2tpLnsSePppSubPppIndex indicates the local identifier of the subscriber PPP session. It is the index of the corresponding conceptual row in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppTable.
tmnxL2tpLnsSePppStatTable	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3		not-accessible	The tmnxL2tpLnsSePppStatTable has an entry for each Layer Two Tunneling Protocol Session for which this system acts as LNS. This table is replaced with TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppStatTable.
tmnxL2tpLnsSePppStatEntry	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1		not-accessible	Each conceptual row represents a Layer Two Tunneling Protocol Session. Entries in this table are created and destroyed by the system.
C32 tmnxL2tpLnsSePppStatRxUnkwnProto	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.2	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxUnkwnProto indicates the number of packets with unknown PPP protocol received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxLcpConfRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.3	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxLcpConfRq indicates the number of LCP configure requests received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxLcpConfAk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.4	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxLcpConfAk indicates the number of LCP configure acknowledgements received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxLcpConfNk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.5	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxLcpConfNk indicates the number of negative LCP configure acknowledgements received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxLcpConfRj	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.6	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxLcpConfRj indicates the number of LCP configure rejects received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxLcpTermRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.7	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxLcpTermRq indicates the number of LCP terminate requests received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxLcpTermAk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.8	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxLcpTermAk indicates the number of LCP terminate acknowledgements received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxLcpCodeRj	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.9	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxLcpCodeRj indicates the number of LCP code rejects received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxLcpEchoRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.10	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxLcpEchoRq indicates the number of LCP echo requests received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxLcpEchoRep	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.11	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxLcpEchoRep indicates the number of LCP echo replies received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxLcpProtRj	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.12	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxLcpProtRj indicates the number of LCP protocol rejects received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxLcpDiscRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.13	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxLcpDiscRq indicates the number of LCP discard requests received for this PPP session.
C32 tmnxL2tpLnsSePppStatTxLcpConfRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.14	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxLcpConfRq indicates the number of LCP configure requests transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxLcpConfAk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.15	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxLcpConfAk indicates the number of LCP configure acknowledgements transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxLcpConfNk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.16	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxLcpConfNk indicates the number of negative LCP configure acknowledgements transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxLcpConfRj	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.17	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxLcpConfRj indicates the number of LCP configure rejects transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxLcpTermRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.18	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxLcpTermRq indicates the number of LCP terminate requests transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxLcpTermAk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.19	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxLcpTermAk indicates the number of LCP terminate acknowledgements transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxLcpCodeRj	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.20	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxLcpCodeRj indicates the number of LCP code rejects transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxLcpEchoRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.21	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxLcpEchoRq indicates the number of LCP echo requests transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxLcpEchoRep	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.22	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxLcpEchoRep indicates the number of LCP echo replies transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxLcpProtRj	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.23	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxLcpProtRj indicates the number of LCP protocol rejects transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxLcpDiscRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.24	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxLcpDiscRq indicates the number of LCP discard requests transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatRxPapAuthRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.25	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxPapAuthRq indicates the number of PAP authentication requests received for this PPP session.
C32 tmnxL2tpLnsSePppStatTxPapAuthAk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.26	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxPapAuthAk indicates the number of PAP authentication acknowledgements transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxPapAuthNk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.27	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxPapAuthNk indicates the number of negative PAP authentication acknowledgements transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatRxChapResp	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.28	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxChapResp indicates the number of CHAP authentication responses received for this PPP session.
C32 tmnxL2tpLnsSePppStatTxChapChall	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.29	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxChapChall indicates the number of CHAP authentication challenges transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxChapSucc	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.30	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxChapSucc indicates the number of CHAP authentication acknowledgements transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxChapFail	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.31	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxChapFail indicates the number of negative CHAP authentication acknowledgements transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatRxIpcpConfRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.32	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxIpcpConfRq indicates the number of IPCP configure requests received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxIpcpConfAk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.33	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxIpcpConfAk indicates the number of IPCP configure acknowledgements received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxIpcpConfNk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.34	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxIpcpConfNk indicates the number of negative IPCP configure acknowledgements received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxIpcpConfRj	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.35	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxIpcpConfRj indicates the number of IPCP configure rejects received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxIpcpTermRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.36	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxIpcpTermRq indicates the number of IPCP terminate requests received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxIpcpTermAk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.37	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxIpcpTermAk indicates the number of IPCP terminate acknowledgements received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxIpcpCodeRj	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.38	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxIpcpCodeRj indicates the number of IPCP code rejects received for this PPP session.
C32 tmnxL2tpLnsSePppStatTxIpcpConfRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.39	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxIpcpConfRq indicates the number of IPCP configure requests transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxIpcpConfAk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.40	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxIpcpConfAk indicates the number of IPCP configure acknowledgements transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxIpcpConfNk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.41	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxIpcpConfNk indicates the number of negative IPCP configure acknowledgements transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxIpcpConfRj	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.42	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxIpcpConfRj indicates the number of IPCP configure rejects transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxIpcpTermRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.43	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxIpcpTermRq indicates the number of IPCP terminate requests transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxIpcpTermAk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.44	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxIpcpTermAk indicates the number of IPCP terminate acknowledgements transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxIpcpCodeRj	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.45	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxIpcpCodeRj indicates the number of IPCP code rejects transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatRxIpv6cpCfRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.46	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxIpv6cpCfRq indicates the number of IPv6 Control Protocol (IPv6CP) configure requests received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxIpv6cpCfAk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.47	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxIpv6cpCfAk indicates the number of IPv6CP configure acknowledgements received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxIpv6cpCfNk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.48	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxIpv6cpCfNk indicates the number of negative IPv6CP configure acknowledgements received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxIpv6cpCfRj	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.49	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxIpv6cpCfRj indicates the number of IPv6CP configure rejects received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxIpv6cpTmRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.50	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxIpv6cpTmRq indicates the number of IPv6CP terminate requests received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxIpv6cpTmAk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.51	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxIpv6cpTmAk indicates the number of IPv6CP terminate acknowledgements received for this PPP session.
C32 tmnxL2tpLnsSePppStatRxIpv6cpCdRj	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.52	Counter32	read-only	The value of tmnxL2tpLnsSePppStatRxIpv6cpCdRj indicates the number of IPv6CP code rejects received for this PPP session.
C32 tmnxL2tpLnsSePppStatTxIpv6cpCfRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.53	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxIpv6cpCfRq indicates the number of IPv6CP configure requests transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxIpv6cpCfAk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.54	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxIpv6cpCfAk indicates the number of IPv6CP configure acknowledgements transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxIpv6cpCfNk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.55	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxIpv6cpCfNk indicates the number of negative IPv6CP configure acknowledgements transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxIpv6cpCfRj	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.56	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxIpv6cpCfRj indicates the number of IPv6CP configure rejects transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxIpv6cpTmRq	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.57	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxIpv6cpTmRq indicates the number of IPv6CP terminate requests transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxIpv6cpTmAk	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.58	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxIpv6cpTmAk indicates the number of IPv6CP terminate acknowledgements transmitted for this PPP session.
C32 tmnxL2tpLnsSePppStatTxIpv6cpCdRj	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.59	Counter32	read-only	The value of tmnxL2tpLnsSePppStatTxIpv6cpCdRj indicates the number of IPv6CP code rejects transmitted for this PPP session.
tmnxL2tpLnsSeMRtTable	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.4		not-accessible	The tmnxL2tpLnsSeMRtTable contains managed routes for Layer Two Tunneling Protocol Sessions for which this system acts as LNS. This table is replaced with TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppMRtTable
tmnxL2tpLnsSeMRtEntry	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.4.1		not-accessible	Each conceptual row represents a managed route of an L2TP session for which this system acts as LNS.
IPt tmnxL2tpLnsSeMRtAddrType	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.4.1.1	InetAddressType	not-accessible	The value of tmnxL2tpLnsSeMRtAddrType indicates the address type of tmnxL2tpLnsSeMRtAddr.
IP tmnxL2tpLnsSeMRtAddr	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.4.1.2	InetAddress	not-accessible	The value of tmnxL2tpLnsSeMRtAddr indicates the IP address of the managed route.
ADR tmnxL2tpLnsSeMRtPrefixLen	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.4.1.3	InetAddressPrefixLength	not-accessible	The value of tmnxL2tpLnsSeMRtPrefixLen indicates the prefix length of the subnet associated with tmnxL2tpLnsSeMRtAddr.
TMN tmnxL2tpLnsSeMRtStatus	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.4.1.4	TmnxManagedRouteStatus	read-only	The value of tmnxL2tpLnsSeMRtStatus indicates the state of this managed route.
tmnxL2tpLnsSeOvrTable	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6		not-accessible	The tmnxL2tpLnsSeOvrTable contains QoS (Quality of Service) overrides for Layer Two Tunneling Protocol Sessions for which this system acts as LNS. This table is replaced with TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppOvrTable.
tmnxL2tpLnsSeOvrEntry	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1		not-accessible	Each conceptual row represents QoS overrides information of an L2TP session for which this system acts as LNS.
TDI tmnxL2tpLnsSeOvrDirection	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.1	TDirection	not-accessible	The value of tmnxL2tpLnsSeOvrDirection indicates if this row specifies ingress or egress qos override parameters.
TQO tmnxL2tpLnsSeOvrType	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.2	TQosOverrideType	not-accessible	The value of tmnxL2tpLnsSeOvrType indicates what field has been overridden by this row.
I32 tmnxL2tpLnsSeOvrTypeId	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.3	Integer32	not-accessible	The value of tmnxL2tpLnsSeOvrTypeId indicates the ID of the queue/policer that has been overridden by this row. If the value of tmnxL2tpLnsSeOvrType is not 'queue (1)' or 'policer (2)', this field must be set to zero (0).
TNA tmnxL2tpLnsSeOvrTypeName	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.4	TNamedItemOrEmpty	not-accessible	The value of tmnxL2tpLnsSeOvrTypeName indicates the name of the scheduler/arbiter that has been overridden by this row. If the value of tmnxL2tpLnsSeOvrType is not 'arbiter (4)' or 'scheduler (5)', this field must be set to zero (0).
TPI tmnxL2tpLnsSeOvrPIR	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.5	TPIRRateOverride	read-only	The value of tmnxL2tpLnsSeOvrPIR indicates the PIR rate in kbps allowed for the object overridden by this row.
TCI tmnxL2tpLnsSeOvrCIR	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.6	TCIRRateOverride	read-only	The value of tmnxL2tpLnsSeOvrCIR indicates the CIR rate in kbps allowed for the object overridden by this row.
TBU tmnxL2tpLnsSeOvrCBS	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.7	TBurstSizeBytesOverride	read-only	The value of tmnxL2tpLnsSeOvrCBS indicates the amount of reserved buffer space (in bytes) for the object overridden by this row.
TBU tmnxL2tpLnsSeOvrMBS	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.8	TBurstSizeBytesOverride	read-only	The value of tmnxL2tpLnsSeOvrMBS indicates the maximum amount of reserved buffer space (in bytes) for the object overridden by this row.
tmnxL2tpLnsSeAleTable	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.7		not-accessible	The tmnxL2tpLnsSeAleTable contains Access Loop Encapsulation information for Layer Two Tunneling Protocol Sessions for which this system acts as LNS. This table is replaced with TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppAleTable.
tmnxL2tpLnsSeAleEntry	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.7.1		not-accessible	Each conceptual row represents access loop encapsulation information of an L2TP session for which this system acts as LNS.
TMN tmnxL2tpLnsSeAleDatalink	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.7.1.1	TmnxAccessLoopEncapDataLink	read-only	The value of tmnxL2tpLnsSeAleDatalink indicates the data link used by the subscriber host on the DSL access loop.
TMN tmnxL2tpLnsSeAleEncaps1	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.7.1.2	TmnxAccessLoopEncaps1	read-only	The value of tmnxL2tpLnsSeAleEncaps1 indicates the encapsulation used by the subscriber host on the DSL access loop.
TMN tmnxL2tpLnsSeAleEncaps2	1.3.6.1.4.1.6527.3.1.2.60.1.5.1.7.1.3	TmnxAccessLoopEncaps2	read-only	The value of tmnxL2tpLnsSeAleEncaps2 indicates the encapsulation used by the subscriber host on the DSL access loop.
tmnxL2tpSeOpObjs	1.3.6.1.4.1.6527.3.1.2.60.1.5.2
tmnxL2tpSeStopTable	1.3.6.1.4.1.6527.3.1.2.60.1.5.2.1		not-accessible	The tmnxL2tpSeStopTable has an entry for each active Layer Two Tunneling Protocol Session.
tmnxL2tpSeStopEntry	1.3.6.1.4.1.6527.3.1.2.60.1.5.2.1.1		not-accessible	Each conceptual row presents an operations interface to stop a Layer Two Tunneling Protocol session. Entries in this table are created and destroyed by the system.
TMN tmnxL2tpSeStop	1.3.6.1.4.1.6527.3.1.2.60.1.5.2.1.1.1	TmnxActionType	read-write	Setting this object to 'doAction (1)' triggers an attempt to stop the control connection for this L2TP session. Reading this object returns the value 'notApplicable'.
tmnxL2tpLnsIsaObjs	1.3.6.1.4.1.6527.3.1.2.60.1.6
tmnxL2tpLnsIsaGrpObjs	1.3.6.1.4.1.6527.3.1.2.60.1.6.1
tmnxL2tpIsaGrpTable	1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1		not-accessible	The tmnxL2tpIsaGrpTable contains objects to configure L2TP Integrated Service Adaptor (ISA) Groups. The ISA Groups are used for the L2TP Network Server (LNS) function. An L2TP ISA group is used to represent multiple hardware adaptors as a single entity, allowing for load balancing between multiple L2TP ISA's.
tmnxL2tpIsaGrpEntry	1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1		not-accessible	Each conceptual row represents a Layer Two Tunneling Protocol Integrated Service Adaptor Group. Entries in this table can be created or deleted via SNMP operations.
TMN tmnxL2tpIsaGrpId	1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1.1	TmnxL2tpIsaGrpId	not-accessible	The value of the object tmnxL2tpIsaGrpId specifies the identifier of the L2TP Integrated Service Adaptor group.
ROW tmnxL2tpIsaGrpRowStatus	1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1.2	RowStatus	read-create	The value of tmnxL2tpIsaGrpRowStatus specifies the row status of this row.
TIM tmnxL2tpIsaGrpLastMgmtChange	1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1.3	TimeStamp	read-only	The value of tmnxL2tpIsaGrpLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
TIT tmnxL2tpIsaGrpDescription	1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1.4	TItemDescription	read-create	The value of tmnxL2tpIsaGrpDescription specifies the description of this L2TP ISA group.
TMN tmnxL2tpIsaGrpAdminState	1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1.5	TmnxAdminState	read-create	The value of tmnxL2tpIsaGrpAdminState specifies the administrative state of this L2TP ISA group.
TMN tmnxL2tpIsaGrpOperState	1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1.6	TmnxOperState	read-only	The value of tmnxL2tpIsaGrpOperState indicates the operational status of this L2TP ISA group.
TNA tmnxL2tpIsaGrpPortPlcy	1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1.8	TNamedItemOrEmpty	read-create	The value of tmnxL2tpIsaGrpPortPlcy specifies the port policy of this L2TP ISA group. This object refers to a row in the TIMETRA-PORT-MIB::tmnxPortPlcyTable. If a port policy is associated with an L2TP ISA group, ports created for this group can take applicable configuration from that port policy.
tmnxL2tpLnsIsaMdaObjs	1.3.6.1.4.1.6527.3.1.2.60.1.6.2
tmnxL2tpIsaMdaTable	1.3.6.1.4.1.6527.3.1.2.60.1.6.2.1		not-accessible	The tmnxL2tpIsaMdaTable contains objects to configure the L2TP ISA Group Media Dependent Adapters (MDA).
tmnxL2tpIsaMdaEntry	1.3.6.1.4.1.6527.3.1.2.60.1.6.2.1.1		not-accessible	Each conceptual row represents an L2TP ISA Media Dependent Adapter (MDA) of an L2TP ISA Group. Entries in this table can be created or deleted via SNMP operations.
ROW tmnxL2tpIsaMdaRowStatus	1.3.6.1.4.1.6527.3.1.2.60.1.6.2.1.1.1	RowStatus	read-create	The value of tmnxL2tpIsaMdaRowStatus specifies the row status of this row.
TIM tmnxL2tpIsaMdaLastMgmtChange	1.3.6.1.4.1.6527.3.1.2.60.1.6.2.1.1.2	TimeStamp	read-only	The value of tmnxL2tpIsaMdaLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
T/F tmnxL2tpIsaMdaDrain	1.3.6.1.4.1.6527.3.1.2.60.1.6.2.1.1.3	TruthValue	read-create	The value of tmnxL2tpIsaMdaDrain specifies if this MDA is drained from LNS tunnels.
TMN tmnxL2tpIsaMdaStop	1.3.6.1.4.1.6527.3.1.2.60.1.6.2.1.1.4	TmnxActionType	read-create	Setting the value of tmnxL2tpIsaMdaStop to 'doAction' triggers an attempt to stop all PPP sessions on this L2TP ISA MDA. Reading the value of tmnxL2tpIsaMdaStop results in 'not-applicable'.
tmnxL2tpLnsIsaMdaStatObjs	1.3.6.1.4.1.6527.3.1.2.60.1.6.3
tmnxL2tpIsaMdaStatTable	1.3.6.1.4.1.6527.3.1.2.60.1.6.3.1		not-accessible	The tmnxL2tpIsaMdaStatTable contains status and statistics information about the Media Dependent Adapters (MDA) of an L2TP ISA Group.
tmnxL2tpIsaMdaStatEntry	1.3.6.1.4.1.6527.3.1.2.60.1.6.3.1.1		not-accessible	Each conceptual row contains status and statistics information about a Media Dependent Adapter (MDA) of an L2TP ISA Group. Entries in this table are created and removed automatically by the system.
TMN tmnxL2tpIsaMdaStatOperState	1.3.6.1.4.1.6527.3.1.2.60.1.6.3.1.1.1	TmnxL2tpIsaMdaOperState	read-only	The value of tmnxL2tpIsaMdaStatOperState indicates the operational state of this L2TP ISA MDA.
G32 tmnxL2tpIsaMdaStatSessions	1.3.6.1.4.1.6527.3.1.2.60.1.6.3.1.1.2	Gauge32	read-only	The value of tmnxL2tpIsaMdaStatOperState indicates the actual number of PPP sessions on this L2TP ISA MDA.
tmnxL2tpIsaMdaVRtrTable	1.3.6.1.4.1.6527.3.1.2.60.1.6.3.2		not-accessible	The tmnxL2tpIsaMdaVRtrTable contains status information about the L2TP ISA Group Media Dependent Adapters (MDA) with respect to the associated Virtual Routers.
tmnxL2tpIsaMdaVRtrEntry	1.3.6.1.4.1.6527.3.1.2.60.1.6.3.2.1		not-accessible	Each conceptual row represents the association of an L2TP ISA Media Dependent Adapter (MDA) and a Virtual Router. Entries in this table are created and removed automatically by the system.
TMN tmnxL2tpIsaMdaVRtrOperState	1.3.6.1.4.1.6527.3.1.2.60.1.6.3.2.1.1	TmnxOperState	read-only	The value of tmnxL2tpIsaMdaVRtrOperState indicates the operational state of this L2TP ISA MDA with respect to this Virtual Router.
tmnxL2tpLnsSvcObjs	1.3.6.1.4.1.6527.3.1.2.60.1.7
tmnxL2tpLnsIfObjs	1.3.6.1.4.1.6527.3.1.2.60.1.7.1
tmnxL2tpLnsIfTable	1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1		not-accessible	This table is supported for backwards compatibility; the recommended way to configure L2TP LNS Group-Interfaces is by means of the TIMETRA-SERV-MIB::svcIfSapCfgTable. The tmnxL2tpLnsIfTable contains objects to configure L2TP LNS Group-Interfaces. Entries in this table are created and destroyed by the system. The system automatically creates an entry in this table for each entry in the TIMETRA-SERV-MIB::iesIfTable where the value of iesIfType is equal to 'group' and the value of iesIfGroupInterfaceType is equal to 'lns'. Deletion of such a row in the iesIfTable results in the same fate for the corresponding row in this table.
tmnxL2tpLnsIfEntry	1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1		not-accessible	L2TP LNS specific information about a specific group interface. Unlike regular subscriber traffic, that enters the system through Service Access Points (SAP) on a group-interface, traffic for PPP subscriber sessions terminated by the LNS function, enters the system through a plain layer 3 interface; this traffic is relayed for processing to an L2TP ISA MDA; it re-enters through an internal LNS group interface; this entry allows to configure subscriber management parameters for PPP subscriber sessions.
TIM tmnxL2tpLnsIfLastMgmtChange	1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.1	TimeStamp	read-only	The value of tmnxL2tpLnsIfLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
TIT tmnxL2tpLnsIfDescription	1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.2	TItemDescription	read-create	The value of tmnxL2tpLnsIfDescription specifies the description of this L2TP LNS interface.
TNA tmnxL2tpLnsIfDefSubProfile	1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.3	TNamedItemOrEmpty	read-create	The value of tmnxL2tpLnsIfDefSubProfile specifies the default subscriber profile of the subscribers of this LNS interface.
TNA tmnxL2tpLnsIfDefSlaProfile	1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.4	TNamedItemOrEmpty	read-create	The value of tmnxL2tpLnsIfDefSlaProfile specifies the default SLA profile of the subscribers of this LNS interface.
TNA tmnxL2tpLnsIfDefAppProfile	1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.5	TNamedItemOrEmpty	read-create	The value of tmnxL2tpLnsIfDefSlaProfile specifies the default application profile of the subscribers of this LNS interface.
TNA tmnxL2tpLnsIfSubIdentPolicy	1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.6	TNamedItemOrEmpty	read-create	The value of tmnxL2tpLnsIfSubIdentPolicy specifies the subscriber identification policy of the subscribers of this LNS interface.
TMN tmnxL2tpLnsIfDefSubIdent	1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.7	TmnxDefSubIdSource	read-create	The value of tmnxL2tpLnsIfDefSubIdent specifies the default subscriber identification of the subscribers of this LNS interface. This value is used in case no other source (like Radius) provides a subscriber identification string. If the value of this object is set to 'useSapId', the SAP-id will be used as the default subscriber identification string; in this case, tmnxL2tpLnsIfDefSubIdentString must contain the empty string, so any non-empty string in tmnxL2tpLnsIfDefSubIdentString will be set to an empty string. If the value of this object is set to 'useAutoId', the auto-generated subscriber identification string, as defined in tmnxSubMgmtAutoSubIdObjs, is used as the default subscriber identification string. In this case, tmnxL2tpLnsIfDefSubIdentString must contain the empty string, so any non-empty string in tmnxL2tpLnsIfDefSubIdentString will be set to an empty string. If the value of this object is set to 'useString', the value of tmnxL2tpLnsIfDefSubIdentString will be used as the default subscriber identification string; in this case, an empty tmnxL2tpLnsIfDefSubIdentString means that there is no default subscriber identification configured.
STR tmnxL2tpLnsIfDefSubIdentString	1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.8	DisplayString	read-create	The value of tmnxL2tpLnsIfDefSubIdentString specifies the default subscriber identification string applicable on the subscribers of this LNS interface.
TNA tmnxL2tpLnsIfDefFilterProfile	1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.9	TNamedItemOrEmpty	read-create	The value of the object tmnxL2tpLnsIfDefFilterProfile specifies the default filter profile for this LNS interface. The specified filter profile needs to exists in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubFilterProfileTable.
tmnxL2tpMlpppObjs	1.3.6.1.4.1.6527.3.1.2.60.1.8
tmnxL2tpLacMlpppBundleTable	1.3.6.1.4.1.6527.3.1.2.60.1.8.1		not-accessible	The tmnxL2tpLacMlpppBundleTable allows monitoring of MLPPP (Multi Link PPP) bundles of PPP sessions where this system acts as a LAC.
tmnxL2tpLacMlpppBundleEntry	1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1		not-accessible	Each conceptual row represents an MLPPP Bundle associated with PPP sessions for which this system acts as a LAC. Entries in this table are created and destroyed by the system.
U32 tmnxL2tpLacMlpppBundleIndex	1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.1	Unsigned32	not-accessible	The value of the object tmnxL2tpLacMlpppBundleIndex indicates the local identifier of this MLPPP Bundle.
TMN tmnxL2tpLacMlpppBundleSvcId	1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.2	TmnxServId	read-only	The value of tmnxL2tpLacMlpppBundleSvcId indicates the service ID of the IES/VPRN service to which this MLPPP bundle belongs.
TMN tmnxL2tpLacMlpppBundleFwdTuId	1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.3	TmnxL2tpTunnelId	read-only	The value of tmnxL2tpLacMlpppBundleFwdTuId indicates the LTS (L2TP Tunnel Stitching) tunnel ID if this bundle is associated with PPP sessions that are stitched to another L2TP tunnel. Otherwise, the value of tmnxL2tpLacMlpppBundleFwdTuId is equal to zero.
TMN tmnxL2tpLacMlpppBundleUserName	1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.4	TmnxPppoeUserNameOrEmpty	read-only	The value of tmnxL2tpLacMlpppBundleUserName indicates the user name of the subscriber associated with this MLPPP bundle, or another string used to identify that subscriber.
TMN tmnxL2tpLacMlpppBundleLocEpClass	1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.5	TmnxMlpppEpClass	read-only	The value of tmnxL2tpLacMlpppBundleLocEpClass indicates the address class of the local endpoint. If the value of tmnxL2tpLacMlpppBundleLocEpClass is equal to 'null', the address class of the MLPPP Endpoint Discriminator option was not present in a received Configure-Request.
OCT tmnxL2tpLacMlpppBundleLocEpAddr	1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.6	OCTET STRING	read-only	The value of tmnxL2tpLacMlpppBundleLocEpAddr indicates the address of the local MLPPP Endpoint. Its interpretation depends on the value of tmnxL2tpLacMlpppBundleLocEpClass.
TMN tmnxL2tpLacMlpppBundleRemEpClass	1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.7	TmnxMlpppEpClass	read-only	The value of tmnxL2tpLacMlpppBundleRemEpClass indicates the address class of the local endpoint. If the value of tmnxL2tpLacMlpppBundleRemEpClass is equal to 'null', the address class of the MLPPP Endpoint Discriminator option was not present in a received Configure-Request.
OCT tmnxL2tpLacMlpppBundleRemEpAddr	1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.8	OCTET STRING	read-only	The value of tmnxL2tpLacMlpppBundleRemEpAddr indicates the address of the local MLPPP Endpoint. Its interpretation depends on the value of tmnxL2tpLacMlpppBundleRemEpClass.
tmnxL2tpLacMlpppLinkTable	1.3.6.1.4.1.6527.3.1.2.60.1.8.2		not-accessible	The tmnxL2tpLacMlpppLinkTable contains the subscriber MLPPP (Multi Link PPP) links where this system acts as a LAC, ordered per bundle.
tmnxL2tpLacMlpppLinkEntry	1.3.6.1.4.1.6527.3.1.2.60.1.8.2.1		not-accessible	Each conceptual row represents an MLPPP Link associated with a PPP session for which this system acts as a LAC. Entries in this table are created and destroyed by the system.
TMN tmnxL2tpLacMlpppLinkState	1.3.6.1.4.1.6527.3.1.2.60.1.8.2.1.1	TmnxL2tpSeOperState	read-only	The value of tmnxL2tpLacMlpppLinkState indicates the operational state of the session associated with this MLPPP link.
TIM tmnxL2tpTableLastCh	1.3.6.1.4.1.6527.3.1.2.60.1.10	TimeStamp	read-only	The value of tmnxL2tpTableLastCh indicates the sysUpTime at the time of the most recent management-initiated change to the tmnxL2tpTable.
TIM tmnxL2tpTgCfgTableLastCh	1.3.6.1.4.1.6527.3.1.2.60.1.11	TimeStamp	read-only	The value of the object tmnxL2tpTgCfgTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpTgCfgTable.
TIM tmnxL2tpTuCfgTableLastCh	1.3.6.1.4.1.6527.3.1.2.60.1.12	TimeStamp	read-only	The value of the object tmnxL2tpTuCfgTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpTuCfgTable.
TIM tmnxL2tpTuStatusTableLastCh	1.3.6.1.4.1.6527.3.1.2.60.1.13	TimeStamp	read-only	The value of the object tmnxL2tpTuStatusTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpTuStatusTable.
TIM tmnxL2tpSeStatusTableLastCh	1.3.6.1.4.1.6527.3.1.2.60.1.14	TimeStamp	read-only	The value of the object tmnxL2tpSeStatusTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpSeStatusTable.
TIM tmnxL2tpIsaGrpTableLastCh	1.3.6.1.4.1.6527.3.1.2.60.1.15	TimeStamp	read-only	The value of the object tmnxL2tpIsaGrpTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpIsaGrpTable.
TIM tmnxL2tpIsaMdaTableLastCh	1.3.6.1.4.1.6527.3.1.2.60.1.16	TimeStamp	read-only	The value of the object tmnxL2tpIsaMdaTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpIsaMdaTable.
TIM tmnxL2tpIsaMdaStatTableLastCh	1.3.6.1.4.1.6527.3.1.2.60.1.17	TimeStamp	read-only	The value of the object tmnxL2tpIsaMdaStatTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpIsaGrpTable.
TIM tmnxL2tpLnsTgPppTableLastCh	1.3.6.1.4.1.6527.3.1.2.60.1.18	TimeStamp	read-only	The value of the object tmnxL2tpLnsTgPppTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpLnsTgPppTable.
TIM tmnxL2tpLnsTuPppTableLastCh	1.3.6.1.4.1.6527.3.1.2.60.1.19	TimeStamp	read-only	The value of the object tmnxL2tpLnsTuPppTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpLnsTuPppTable.
TIM tmnxL2tpLnsSePppTableLastCh	1.3.6.1.4.1.6527.3.1.2.60.1.20	TimeStamp	read-only	The value of the object tmnxL2tpLnsSePppTableLastCh indicates the value of sysUpTime at the time of the last update of an entry in the tmnxL2tpLnsSePppTable.
TIM tmnxL2tpLnsSeAleTableLastCh	1.3.6.1.4.1.6527.3.1.2.60.1.21	TimeStamp	read-only	The value of the object tmnxL2tpLnsSeAleTableLastCh indicates the value of sysUpTime at the time of the last update of an entry in the tmnxL2tpLnsSeAleTable.
tmnxL2tpAccountingObjs	1.3.6.1.4.1.6527.3.1.2.60.1.100
tmnxL2tpApTable	1.3.6.1.4.1.6527.3.1.2.60.1.100.1		not-accessible	The tmnxL2tpApTable allows configuration of RADIUS based accounting policies for L2TP (Layer Two Tunneling Protocol) tunnel accounting.
tmnxL2tpApEntry	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1		not-accessible	Each entry represents the configuration for an L2TP RADIUS Accounting Policy. Entries in this table can be created and deleted via SNMP SET operations to tmnxL2tpApRowStatus.
TNA tmnxL2tpApName	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.1	TNamedItem	not-accessible	The value of tmnxL2tpApName specifies the name of an L2TP RADIUS Accounting Policy.
ROW tmnxL2tpApRowStatus	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.2	RowStatus	read-create	The value of tmnxL2tpApRowStatus controls the creation and deletion of rows in the table. An attempt to delete a row that is referred to will fail with an inconsistentValue error.
TIM tmnxL2tpApLastMgmtChange	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.3	TimeStamp	read-only	The value of tmnxL2tpApLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this policy.
TIT tmnxL2tpApDescription	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.4	TItemDescription	read-create	The value of tmnxL2tpApDescription specifies the user provided description of this policy.
BIT tmnxL2tpApType	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.5	Bits	read-create	The value of tmnxL2tpApType specifies the type of accounting for the L2TP tunnels associated with this policy.
TMN tmnxL2tpApServerVRtrID	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.6	TmnxVRtrIDOrZero	read-create	The value of tmnxL2tpApServerVRtrID specifies the virtual router instance applicable for the set of configured RADIUS servers (tmnxL2tpApRadServTable). The value of this object cannot be changed once a RADIUS server is configured for this policy. When the value is '0', both base and management router instances are available.
TMN tmnxL2tpApServerAlgorithm	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.7	TmnxSubRadServAlgorithm	read-create	The value of tmnxL2tpApServerAlgorithm specifies the algorithm used to select a RADIUS server from the list of configured servers (tmnxL2tpApRadServTable).
U32 tmnxL2tpApServerRetry	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.8	Unsigned32	read-create	The value of tmnxL2tpApServerRetry specifies the number of RADIUS requests towards the same RADIUS server.
IPt tmnxL2tpApServerSrcAddrType	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.9	InetAddressType	read-create	The value of tmnxL2tpApServerSrcAddrType specifies the type of address stored in tmnxL2tpApServerSrcAddr.
IP tmnxL2tpApServerSrcAddr	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.10	InetAddress	read-create	The value of tmnxL2tpApServerSrcAddr specifies the source address of a RADIUS packet for L2TP accounting; it must be a valid unicast address (otherwise a wrongValue error is returned). If this object is configured with the address of a router interface (ref TIMETRA-VRTR-MIB::vRiaIpAddress) the RADIUS client uses it while making a request to the server. If the address is not configured or is not the address of one of the interfaces, the source address is based on the address of the RADIUS server; if the server address is in-band, the client uses the system IP address; if it is out-of-band, the source address is the address of the management interface (the addresses can be found in TIMETRA-VRTR-MIB::vRiaIpAddress).
U32 tmnxL2tpApServerTimeout	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.11	Unsigned32	read-create	The value of tmnxL2tpApServerTimeout specifies the timeout between retries towards the same RADIUS server.
BIT tmnxL2tpApIncludeAttributes	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.12	Bits	read-create	The value of tmnxL2tpApIncludeAttributes specifies what RADIUS attributes the system should include into RADIUS accounting messages.
TNA tmnxL2tpApRequestScriptPlcy	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.13	TNamedItemOrEmpty	read-create	The value of tmnxL2tpApRequestScriptPlcy specifies the RADIUS script policy used to change the RADIUS attributes of the outgoing Accounting-Request messages.
TMN tmnxL2tpApNasPortIdPfixType	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.14	TmnxSubNasPortPrefixType	read-create	The value of tmnxL2tpApNasPortIdPfixType specifies what type of prefix will be added to the NAS-Port-Id attribute if included in RADIUS accounting-request messages. This field is only applicable if the 'nasPortId' bit is set in tmnxL2tpApIncludeAttributes.
STR tmnxL2tpApNasPortIdPfixString	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.15	DisplayString	read-create	The value of tmnxL2tpApNasPortIdPfixString specifies the user configurable string to be added as prefix to the NAS-Port-Id attribute if included in RADIUS accounting-request messages. This field is only applicable if the 'nasPortId' bit is set in tmnxL2tpApIncludeAttributes and tmnxL2tpApNasPortIdPfixType is set to 'userString'.
TMN tmnxL2tpApNasPortIdSfixType	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.16	TmnxSubNasPortSuffixType	read-create	The value of tmnxL2tpApNasPortIdSfixType specifies what type of suffix will be added to the NAS-Port-Id attribute if included in RADIUS accounting-request messages. This field is only applicable if the 'nasPortId' bit is set in tmnxL2tpApIncludeAttributes.
TMN tmnxL2tpApNasPortTypeType	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.17	TmnxSubNasPortTypeType	read-create	The value of tmnxL2tpApNasPortTypeType specifies what kind of value will be put in the RADIUS NAS-Port-Type attribute if included in RADIUS accounting-request messages. This field is only applicable if the 'nasPortType' bit is set in tmnxL2tpApIncludeAttributes.
U32 tmnxL2tpApNasPortTypeValue	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.18	Unsigned32	read-create	The value of tmnxL2tpApNasPortTypeValue specifies what value will be put in the RADIUS NAS-Port-Type attribute if included in RADIUS accounting-request messages. This field is only applicable if the 'nasPortType' bit is set in tmnxL2tpApIncludeAttributes and the value of the object tmnxL2tpApNasPortTypeType is equal to 'config'.
TMN tmnxL2tpApNasPortBitspec	1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.19	TmnxBinarySpecification	read-create	The value of tmnxL2tpApNasPortBitspec specifies what number will be put in the RADIUS NAS-Port attribute if included in RADIUS accounting-request messages. This field is only applicable if the 'nasPort' bit is set in tmnxL2tpApIncludeAttributes. ::= 'o' \| 'i' \| 's' \| 'm' \| 'p' \| 'v' \| 'c' 'c' - ATM VCI (Virtual Channel Identifier) 'i' - inner VLAN ID 'm' - MDA number 'o' - outer VLAN ID 'p' - port number 's' - slot number 'v' - ATM VPI (Virtual Path Identifier) Maximum 32 bits can be specified. If less than 32 bits are specified, the least significant bits are used and the omitted higher bits are set to zero. Example: 12o12i*2s01 means 'the 12 least significant bits of the outer VLAN ID, followed by the 12 least significant bits of the inner VLAN ID, followed by the two least significant bits of the slot number, followed by a zero and a one-bit', stored in network order in the least significant bits: 0000ooooooooooooiiiiiiiiiiiiss01.
tmnxL2tpApServTable	1.3.6.1.4.1.6527.3.1.2.60.1.100.2		not-accessible	The tmnxL2tpApServTable allows the configuration of objects related to a particular RADIUS server associated with a particular L2TP RADIUS Accounting Policy.
tmnxL2tpApServEntry	1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1		not-accessible	Each entry represents the configuration for a particular RADIUS server. Entries in this table can be created and deleted via SNMP SET operations to tmnxL2tpApServRowStatus.
U32 tmnxL2tpApServIndex	1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.1	Unsigned32	not-accessible	The value of tmnxL2tpApServIndex specifies the index of this RADIUS server in the set of servers associated with this L2TP accounting policy.
ROW tmnxL2tpApServRowStatus	1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.2	RowStatus	read-create	The value of tmnxL2tpApServRowStatus controls the creation and deletion of rows in the table.
TIM tmnxL2tpApServLastMgmtChange	1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.3	TimeStamp	read-only	The value tmnxL2tpApServLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this conceptual row.
IPt tmnxL2tpApServAddrType	1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.5	InetAddressType	read-create	The value of tmnxL2tpApServAddrType specifies the type of address stored in tmnxL2tpApServAddr.
IP tmnxL2tpApServAddr	1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.6	InetAddress	read-create	The value of tmnxL2tpApServAddr specifies the IP address of the RADIUS server. A valid unicast IP address must be specified at row creation time.
STR tmnxL2tpApServSecret	1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.7	DisplayString	read-create	The value of tmnxL2tpApServSecret specifies the secret key associated with the RADIUS server. A non-empty value must be specified at row creation time. An SNMP get request on this object always returns an empty string.
U32 tmnxL2tpApServAcctPort	1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.8	Unsigned32	read-create	The value of tmnxL2tpApServAcctPort specifies the UDP port number on which to contact the RADIUS server for accounting.
TMN tmnxL2tpApServOperState	1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.9	TmnxOperState	read-only	The value of tmnxL2tpApServOperState indicates the operational state of the RADIUS server.
tmnxL2tpApServStatsTable	1.3.6.1.4.1.6527.3.1.2.60.1.100.3		not-accessible	The tmnxL2tpApServStatsTable presents statistics of l2tp-accounting-policies' RADIUS servers.
tmnxL2tpApServStatsEntry	1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1		not-accessible	Each row represents statistics about a specific server of a specify L2TP accounting policy. Rows in this table are created automatically by the system.
C32 tmnxL2tpApServStatsTxRequests	1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1.1	Counter32	read-only	The value of tmnxL2tpApServStatsTxRequests indicates the number of RADIUS request packets transmitted for this server.
C32 tmnxL2tpApServStatsRxResponses	1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1.2	Counter32	read-only	The value of tmnxL2tpApServStatsRxResponses indicates the number of RADIUS response packets received from this server.
C32 tmnxL2tpApServStatsReqTimeout	1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1.3	Counter32	read-only	The value of tmnxL2tpApServStatsReqTimeout indicates the number of RADIUS requests that have timed out for this server.
C32 tmnxL2tpApServStatsReqSendFail	1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1.4	Counter32	read-only	The value of tmnxL2tpApServStatsReqSendFail indicates the number of RADIUS request packets that could not be transmitted for this server.
C32 tmnxL2tpApServStatsReqPending	1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1.5	Counter32	read-only	The value of tmnxL2tpApServStatsReqPending indicates the number of RADIUS requests that are currently pending for this server.
C32 tmnxL2tpApServStatsRespInvAuth	1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1.6	Counter32	read-only	The value of tmnxL2tpApServStatsRespInvAuth indicates the number of RADIUS response packets with an invalid Authenticator received from this server.
C32 tmnxL2tpApServStatsSendRetries	1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1.7	Counter32	read-only	The value of tmnxL2tpApServStatsSendRetries indicates the number of retries to a different server for a single accounting request for this connection with this RADIUS server.
TIM tmnxL2tpApTableLastCh	1.3.6.1.4.1.6527.3.1.2.60.1.100.100	TimeStamp	read-only	The value of the object tmnxL2tpApTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpApTable.
TIM tmnxL2tpApServTableLastCh	1.3.6.1.4.1.6527.3.1.2.60.1.100.101	TimeStamp	read-only	The value of the object tmnxL2tpApServTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpApServTable.
tmnxL2tpNotificationObjs	1.3.6.1.4.1.6527.3.1.2.60.2
STR tmnxL2tpNotifyDescription	1.3.6.1.4.1.6527.3.1.2.60.2.1	DisplayString	accessible-for-notify	The object tmnxL2tpNotifyDescription is a printable character string.
TMN tmnxL2tpPppNcpFailureProtocol	1.3.6.1.4.1.6527.3.1.2.60.2.20	TmnxPppNcpProtocol	accessible-for-notify	The value of tmnxL2tpPppNcpFailureProtocol indicates the failing NCP protocol.
tmnxL2tpNotifyPrefix	1.3.6.1.4.1.6527.3.1.3.60
tmnxL2tpNotifications	1.3.6.1.4.1.6527.3.1.3.60.0
NTF tmnxL2tpPeerUnreachable	1.3.6.1.4.1.6527.3.1.3.60.0.1			The tmnxL2tpPeerUnreachable notification is sent when an L2TP peer becomes unreachable and when it becomes reachable again.
NTF tmnxL2tpIsaMdaVRtrStateChange	1.3.6.1.4.1.6527.3.1.3.60.0.2			The tmnxL2tpIsaMdaVRtrStateChange notification is sent when the operational state of an L2TP ISA MDA with respect to a Virtual Router changes.
NTF tmnxL2tpLnsSePppSessionFailure	1.3.6.1.4.1.6527.3.1.3.60.0.3			The tmnxL2tpLnsSePppSessionFailure notification is sent when the system could not create a new session in the tmnxL2tpLnsSePppTable.
NTF tmnxL2tpLnsPppNcpFailure	1.3.6.1.4.1.6527.3.1.3.60.0.10			The tmnxL2tpLnsPppNcpFailure notification indicates that there is a NCP phase setup problem.
NTF tmnxL2tpApFailure	1.3.6.1.4.1.6527.3.1.3.60.0.11			The tmnxL2tpApFailure notification is generated when a RADIUS accounting request was not sent out successfully to any of the RADIUS servers in the indicated accounting policy.

RFC description

Manages Layer Two Tunneling Protocol (L2TP) configuration and sessions on Alcatel-Lucent SROS routers.

Start monitoring Nokia/Alcatel-Lucent 7750 SR (SROS) router (L2TP tunnel-group admin/session-limit status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TIMETRA-L2TP-MIB