SL-MAIN-MIB

All MIBs › SL-MAIN-MIB

Organization: SmartOptics AS

Last Updated: 2000-08-28

Description: Root management MIB for SmartOptics SiteLight main control card, covering system info, authentication, trap configuration, software versions, log and configuration file management

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SL-MAIN-MIB?

SL-MAIN-MIB is the root management module for the Main Control Board of SmartOptics's SiteLight optical transport platform, covering system identity, IP networking, authentication, alarms, trap configuration, and software/log/configuration file management. It belongs to the optical-transport-equipment category and exposes a broad mix of configuration data (IP/gateway/subnet), administrative and operational status, and software version tracking. Its monitoring emphasis spans both hardware and software status: slmSysOperStatus and slmSysAdminStatus reflect the control card's operational health, slmSysActiveSwVersion and slmSwRevTable track deployed firmware/software versions, and slmSysCalendarTime/slmSysPmStartOfDay support time-aligned performance monitoring, while alarm activation/deactivation objects (slmSysAlmAct/slmSysAlmDeact) surface fault conditions. It likely relies on SmartOptics's broader per-module MIBs (such as SL-ROADM-MIB or SL-SONET-APS-MIB) which share this main board's system context. It is deployed on SmartOptics SiteLight optical transport chassis in metro/regional DWDM or ROADM network deployments. Loading SL-MAIN-MIB in a MIB Browser exposes this full mix of system, alarm, and software-version objects under a single control-board OID branch, making it a convenient starting point for exploring the SiteLight platform.

IPNetwork Monitor allows you to monitor SNMP objects defined in SL-MAIN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

SmartOptics SiteLight optical transport main control card/chassis

Monitoring Examples

An operator would poll slmSysOperStatus and slmSysAdminStatus to confirm the Main Control Board is administratively enabled and operationally up, and check slmSysActiveSwVersion against slmSwRevTable to verify the running software matches the expected release after an upgrade. Monitoring slmSysAlmAct/slmSysAlmDeact reveals active or cleared alarm conditions on the chassis, useful for catching a control-card fault. Tracking slmSysCalendarTime alongside slmSysPmStartOfDay ensures performance-monitoring bins align correctly with the device's clock, which matters when correlating PM data across the network.

What Can Be Monitored

administrative and operational status
active software version
software revision history
alarm activation/deactivation events
system IP/gateway/subnet configuration
system clock and PM interval start time

Imported Objects

From IF-MIB

InterfaceIndex

From PerfHist-TC-MIB

PerfCurrentCount
PerfIntervalCount
PerfTotalCount

From SL-NE-MIB

sitelight

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Opaque
TimeTicks

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using slmSysTemperature OID:

Select a SmartOptics SiteLight optical transport main control card or chassis as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type slmSysTemperature into the Find box to locate it in the OID tree, then select it and click OK. It reports the current temperature of the PL device, in degrees Celsius. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the reported value exceeds the level expected for healthy operation, since sustained high temperature often precedes thermal shutdown or hardware degradation. Click Finish to create the monitor; you can adjust any parameter later.

See also: slmVcatDelay

OIDs

OID symbolic	OID numeric	Type	Access	Description
slMain	1.3.6.1.4.1.4515.1.3			This MIB module describes the Main Board
slmSys	1.3.6.1.4.1.4515.1.3.1
IP slmSysGatewayAddr	1.3.6.1.4.1.4515.1.3.1.1	IpAddress	read-write	Gateway node IP Address.
IP slmSysSubnetMask	1.3.6.1.4.1.4515.1.3.1.2	IpAddress	read-write	Subnetwork Mask IP Address.
IP slmSysIpAddr	1.3.6.1.4.1.4515.1.3.1.3	IpAddress	read-write	Node IP Address.
INT slmSysAlmAct	1.3.6.1.4.1.4515.1.3.1.4	INTEGER	read-write	Alarm Activation Time specified in Half-Seconds units. Alarm will be considered active only if it has been stable for that time.
INT slmSysAlmDeact	1.3.6.1.4.1.4515.1.3.1.5	INTEGER	read-write	Alarm Clearance Time specified in Half-Seconds units. Alarm will be considered clear only if it has been stable for that time.
INT slmSysAdminStatus	1.3.6.1.4.1.4515.1.3.1.6	INTEGER	read-write	Instruct the system to perform the boot according to the specified type.
INT slmSysOperStatus	1.3.6.1.4.1.4515.1.3.1.7	INTEGER	read-only	The operational system state.
INT slmBoxSize	1.3.6.1.4.1.4515.1.3.1.8	INTEGER	read-only	The box size as was configured in the SEEP.
DAT slmSysCalendarTime	1.3.6.1.4.1.4515.1.3.1.9	DateAndTime	read-write	The system calendar time.
INT slmSysPmStartOfDay	1.3.6.1.4.1.4515.1.3.1.10	INTEGER	read-write	The time of day that marks the beginning of each 1-day interval used in the performance monitoring parameters for all interfaces in the NE. This time is on an hour boundary.
INT slmSysActiveSwVersion	1.3.6.1.4.1.4515.1.3.1.11	INTEGER	read-write	Determines the active software version. This is the version that will be loaded by rebooted cards. It is not legal to set this object to the id of an illegal system software version. swRevFtpStart(3) - is set by the NMS to signal the FTP start. swRevFtpEnd(4) - is set by the NMS to signal the FTP completion. swRevAHot(5) - means to change the active software version to A, and to preform hot restart to all cards. swRevBHot(6) - means to change the active software version to B, and to preform hot restart to all cards. Reading the object returns the current active software version.
slmSwRevTable	1.3.6.1.4.1.4515.1.3.1.12		not-accessible	This table keeps the information about the system software revisions.
slmSwRevEntry	1.3.6.1.4.1.4515.1.3.1.12.1		not-accessible	An entry exist per system revsion type (A or B).
INT slmSwRevDirectory	1.3.6.1.4.1.4515.1.3.1.12.1.1	INTEGER	read-only	The directory name A or B of this system software revision.
INT slmSwRevStatus	1.3.6.1.4.1.4515.1.3.1.12.1.2	INTEGER	read-only	The status of the system software directory content. The value valid(1) means that the data of this entry is valid and that the software is loaded correctly and is currently used. The value copyingToStandby(3) means that the SW is currently being copied to the Standby Switch. During this period the NMS is not allowed to upgrade the SW version. This value is applicable only to the Standby software version. The value invalid(2) means otherwise. This value is applicable only to the Standby software version.
SOF slmSwRevName	1.3.6.1.4.1.4515.1.3.1.12.1.3	SoftwareRevision	read-only	The identification string of the system software revision. This value is taken from the content of the system software configuration data that is downloded with the rest of the software files.
DAT slmSwRevDate	1.3.6.1.4.1.4515.1.3.1.12.1.4	DateAndTime	read-only	The release date of the system software revision. This value is taken from the content of the system software configuration data that is downloded with the rest of the software files.
TIK slmConfigSysUptime	1.3.6.1.4.1.4515.1.3.1.13	TimeTicks	read-only	The number of timer ticks at the last configuration command.
INT slmConfigSysSignalType	1.3.6.1.4.1.4515.1.3.1.14	INTEGER	read-write	This variable identifies whether a SONET or a SDH signal is used across this node. This value is configured by the NMS.
INT slmRebootDelay	1.3.6.1.4.1.4515.1.3.1.16	INTEGER	read-write	The number of seconds to wait before reboot. When this number equal to 0 the reboot should occur immediately. After the reboot command is initiated, the value of this object decrements accordingly. Initially, the object value is 0. It is also possible to change this value after starting the reboot process. Getting the value 0 means that there is no pending reboot process in the background.
INT slmVcatDelayEx	1.3.6.1.4.1.4515.1.3.1.17	INTEGER	read-only	The value of the VCAT delay as was read from the SEEP.
STR slmTid	1.3.6.1.4.1.4515.1.3.1.18	DisplayString	read-write	The SL TL1 name.
INT slmPsuNumber	1.3.6.1.4.1.4515.1.3.1.19	INTEGER	read-write	Let the NMS to configure the number of PSU in the system. If this number mismatch the reality, a mismatch alarm is declared.
INT slmOemType	1.3.6.1.4.1.4515.1.3.1.20	INTEGER	read-only	This value tells the NMS the type of the OEM. This value is read from the SEEP.
STR slmSysName	1.3.6.1.4.1.4515.1.3.1.21	DisplayString	read-only	This value is the shadow of the sysName object.
STR slmSysLocation	1.3.6.1.4.1.4515.1.3.1.22	DisplayString	read-only	This value is the shadow of the sysLocation object.
INT slmSysResetPm	1.3.6.1.4.1.4515.1.3.1.23	INTEGER	read-write	Writing 1 to this object reset the system PM counters.
INT slmSysUplinkRate	1.3.6.1.4.1.4515.1.3.1.24	INTEGER	read-write	This object is used to configure the rate of the Uplink. The configured rate applies to both Uplink ports.
INT slmSysChassisId	1.3.6.1.4.1.4515.1.3.1.25	INTEGER	read-write	This object is used to configure the chassis-id. Node with the same value are considered to be stacked.
INT slmSysNetworkPrefix	1.3.6.1.4.1.4515.1.3.1.26	INTEGER	read-write	This object is used to configure the Network Prefix. The prefix is used when the IP address of the node is assigned automatically. The automatic IP address of the node has the form A.x.y.z where x.y.z is the last 3 bytes of the MAC address 00:05:fd:x:y:z of the box. The A is the assigned Network Prefix. For example if the A is 10 and the MAC address is 00:05:fd:f6:55:11 the automatic IP of the node shall be 10.253.85.17.
IP slmSysLanIpAddr	1.3.6.1.4.1.4515.1.3.1.27	IpAddress	read-write	Node LAN IP Address.
IP slmSysLanSubnetAddr	1.3.6.1.4.1.4515.1.3.1.28	IpAddress	read-write	Node LAN Subnet Address.
T/F slmPmAvailable	1.3.6.1.4.1.4515.1.3.1.29	TruthValue	read-only	This value tells the NMS if the PM support is available. The value is taken from the SEEP and can not be changed.
INT slmPortsNumber	1.3.6.1.4.1.4515.1.3.1.30	INTEGER	read-only	The number of ports in the system. The value is taken from the SEEP.
INT slmEdfaNumber	1.3.6.1.4.1.4515.1.3.1.31	INTEGER	read-only	The number of EDFA units in the system. The value is taken from the SEEP.
INT slmMuxNumber	1.3.6.1.4.1.4515.1.3.1.32	INTEGER	read-only	The number of MUX units in the system. The value is taken from the SEEP.
T/F slmOpticalSwitchExist	1.3.6.1.4.1.4515.1.3.1.33	TruthValue	read-only	Should an Optical Switch unit exist in the system. The value is taken from the SEEP.
STR slmReadCommunity	1.3.6.1.4.1.4515.1.3.1.34	DisplayString	read-write	The SNMP read-only community. This object should be accessible only by the Admin users of the Web.
STR slmWriteCommunity	1.3.6.1.4.1.4515.1.3.1.35	DisplayString	read-write	The SNMP read-write community. This object should be accessible only by the Admin users of the Web.
IP slmSysEffectiveSubnetMask	1.3.6.1.4.1.4515.1.3.1.36	IpAddress	read-only	Effective Management subnetwork mask IP Address.
IP slmSysEffectiveIpAddr	1.3.6.1.4.1.4515.1.3.1.37	IpAddress	read-only	Effective Management IP Address.
IP slmSysLanEffectiveIpAddr	1.3.6.1.4.1.4515.1.3.1.38	IpAddress	read-only	Effective LAN IP Address.
IP slmSysLanEffectiveSubnetAddr	1.3.6.1.4.1.4515.1.3.1.39	IpAddress	read-only	Effective LAN subnetwork mask address.
IP slmSysGatewayEffectiveIpAddr	1.3.6.1.4.1.4515.1.3.1.40	IpAddress	read-only	Effective Gateway IP Address.
INT slmSysMode	1.3.6.1.4.1.4515.1.3.1.41	INTEGER	read-write	System Mode configuration (this object applies to muxponder).
INT slmSysTrapFormat	1.3.6.1.4.1.4515.1.3.1.42	INTEGER	read-write	The format of the sent trap: 1 - the full ifIndex is sent. 2 - only the port number part of the ifIndex is sent.
INT slmSysTemperatureEx	1.3.6.1.4.1.4515.1.3.1.43	INTEGER	read-only	The temperature of the PL device in Celsius.
INT slmNetworkMode	1.3.6.1.4.1.4515.1.3.1.44	INTEGER	read-write	1 - means that the LAN is define on a different vlan than the MNG ports. 2 - means that the LAN is on the same vlan and the MNG ports
INT slm40GConf	1.3.6.1.4.1.4515.1.3.1.45	INTEGER	read-write	g40(0) - No 40G ports (service ports 3..10 are disabled) g41(1) - Single 40G Port 1 (service ports 7,8,9,10 are disabled) g42(2) - Single 40G Port 2 (service ports 3,4,5,6 are disabled) g43(3) - Dual 40G ports
T/F slmRstpEnabled	1.3.6.1.4.1.4515.1.3.1.46	TruthValue	read-write	Enable/Disable the RSTP protocol. Defalut value is TRUE.
T/F slmTopologyEnabled	1.3.6.1.4.1.4515.1.3.1.47	TruthValue	read-write	Enable/Disable the topology discovery protocol. Defalut value is TRUE.
STR slmAdminCommunity	1.3.6.1.4.1.4515.1.3.1.48	DisplayString	read-write	The SNMP admin community. This object should be accessible only by the Admin users of the Web.
STR slmTrapCommunity	1.3.6.1.4.1.4515.1.3.1.49	DisplayString	read-write	The SNMP v1/v2c trap community. This object should be accessible only by the Admin users of the Web.
INT slmSysSnmpVersion	1.3.6.1.4.1.4515.1.3.1.50	INTEGER	read-write	The format of the sent trap: 3 - allow only SNMPv3 pdus. 4 - allow all pdus (coexistance mode).
slmAdmin	1.3.6.1.4.1.4515.1.3.2
slmAdminTable	1.3.6.1.4.1.4515.1.3.2.1		not-accessible	The admin table is used to supply the access level for the user login.
slmAdminEntry	1.3.6.1.4.1.4515.1.3.2.1.1		not-accessible	An entry exist per user.
USE slmAdminLogin	1.3.6.1.4.1.4515.1.3.2.1.1.3	UserLogin	read-create	The user login.
USE slmAdminPassword	1.3.6.1.4.1.4515.1.3.2.1.1.4	UserPassword	read-create	The user password.
ROW slmAdminRowStatus	1.3.6.1.4.1.4515.1.3.2.1.1.5	RowStatus	read-create	This object is used to create and delete rows in the slmAdminTable.
ADM slmAdminAccess	1.3.6.1.4.1.4515.1.3.2.1.1.6	AdminAccess	read-create	The user access level.
INT slmSnmpv3Auth	1.3.6.1.4.1.4515.1.3.2.1.1.7	INTEGER	read-create	The user SNMP v3 authentication mode.
INT slmSnmpv3Priv	1.3.6.1.4.1.4515.1.3.2.1.1.8	INTEGER	read-create	The user SNMP v3 privacy mode.
USE slmSnmpv3Password	1.3.6.1.4.1.4515.1.3.2.1.1.9	UserPassword	read-create	The SNMP v3 Password
slmAuth	1.3.6.1.4.1.4515.1.3.3
slmAuthTable	1.3.6.1.4.1.4515.1.3.3.1		not-accessible	The authentication table is used for creating authentication requests.
slmAuthEntry	1.3.6.1.4.1.4515.1.3.3.1.1		not-accessible	The entry is used to compute the slmAuthCommunity based on the indexes Login and Password. Note that the table contains no data, and when using GetNext it apears to be empty. To compute the community the NMS should Get the field slmAuthCommunity with the corresponding indexes.
USE slmAuthLogin	1.3.6.1.4.1.4515.1.3.3.1.1.1	UserLogin	not-accessible	The user login.
USE slmAuthPassword	1.3.6.1.4.1.4515.1.3.3.1.1.2	UserPassword	not-accessible	The user password.
USE slmAuthCommunity	1.3.6.1.4.1.4515.1.3.3.1.1.3	UserCommunity	read-only	The user community name correponds to slmAuthLogin and slmAuthPassword and which defines user'a access scope. The value of this object is available for reading only after the the first three colunms have been filled
slmLogin	1.3.6.1.4.1.4515.1.3.4
slmTrap	1.3.6.1.4.1.4515.1.3.5
slmTrapDestTable	1.3.6.1.4.1.4515.1.3.5.1		not-accessible	A list of trap destination entries.
slmTrapDestEntry	1.3.6.1.4.1.4515.1.3.5.1.1		not-accessible	This entry includes a destination IP address to which to send traps for this community. An entry in the table is created by the NMS. In order to keep the entry in the table the management should refresh the entry periodicaly. Otherwise it will be deleted by the GNE after 5 minutes.
I32 slmTrapDestAddress	1.3.6.1.4.1.4515.1.3.5.1.1.1	Integer32	read-create	A copy of slmTrapDestIpAddress represented as an integer. Needed due to VxWorks failure to handle an ip address as a table index.
ROW slmTrapDestRowStatus	1.3.6.1.4.1.4515.1.3.5.1.1.2	RowStatus	read-create	This object is used to create and delete rows in the trapDestTable.
USE slmTrapDestCommunity	1.3.6.1.4.1.4515.1.3.5.1.1.3	UserCommunity	read-create	A community to which this destination address belongs. This entry is associated with any eventEntries in the RMON MIB whose value of eventCommunity is equal to the value of this object. Every time an associated event entry sends a trap due to an event, that trap will be sent to each address in the trapDestTable with a trapDestCommunity equal to eventCommunity. This object may not be modified if the associated trapDestStatus object is equal to active(1).
INT slmTrapDestProtVersion	1.3.6.1.4.1.4515.1.3.5.1.1.4	INTEGER	read-create	The SNMP version of the traps which this manager expects to receive.
USE slmTrapUserLogin	1.3.6.1.4.1.4515.1.3.5.1.1.5	UserLogin	read-create	The user login. This is used to describe to the manager the current active login sessions. The NMS should read this value periodicaly in order to refresh its entry, otherwise the entry will be deleted by the GNE after a timeout of 5 minutes.
ADM slmTrapUserAccess	1.3.6.1.4.1.4515.1.3.5.1.1.6	AdminAccess	read-create	The user access.
T/F slmTrapEnable	1.3.6.1.4.1.4515.1.3.5.1.1.7	TruthValue	read-create	TRUE - means that that the alarms are allowed. FALSE - means that all alarms should not be sent for this session.
INT slmTrapPort	1.3.6.1.4.1.4515.1.3.5.1.1.8	INTEGER	read-create	The destination port for to send the trap. The default value is 162.
IP slmTrapDestIpAddress	1.3.6.1.4.1.4515.1.3.5.1.1.9	IpAddress	read-create	The address to send traps on behalf of this entry. This object may not be modified if the associated slmTrapDestStatus object is equal to active(1).
slmTrapLogTable	1.3.6.1.4.1.4515.1.3.5.2		not-accessible	A list of trap log entries.
slmTrapLogEntry	1.3.6.1.4.1.4515.1.3.5.2.1		not-accessible	An entry in the table keeps the log of a single trap.
G32 slmTrapLogId	1.3.6.1.4.1.4515.1.3.5.2.1.1	Gauge32	read-only	The trap log id. The id increments each time a new log entry arrives.
OCT slmTrapLogName	1.3.6.1.4.1.4515.1.3.5.2.1.2	OCTET STRING	read-only	The object id of the trap.
TIK slmTrapLogTimeStamp	1.3.6.1.4.1.4515.1.3.5.2.1.3	TimeTicks	read-only	The trap time stamp.
OCT slmTrapLogParam1	1.3.6.1.4.1.4515.1.3.5.2.1.4	OCTET STRING	read-only	The first parameter of the trap.
OCT slmTrapLogParam2	1.3.6.1.4.1.4515.1.3.5.2.1.5	OCTET STRING	read-only	The second parameter of the trap.
OCT slmTrapLogParam3	1.3.6.1.4.1.4515.1.3.5.2.1.6	OCTET STRING	read-only	The third parameter of the trap.
OCT slmTrapLogParam4	1.3.6.1.4.1.4515.1.3.5.2.1.7	OCTET STRING	read-only	The forth parameter of the trap.
OCT slmTrapLogParam5	1.3.6.1.4.1.4515.1.3.5.2.1.8	OCTET STRING	read-only	The fifth parameter of the trap.
OCT slmTrapLogParam6	1.3.6.1.4.1.4515.1.3.5.2.1.9	OCTET STRING	read-only	The sixth parameter of the trap.
NTF slmTrapSoftwareStatusChange	1.3.6.1.4.1.4515.1.3.5.4			A slmTrapSoftwareStatusChange trap is sent when the value of the slmSwRevStatus of one of the directories changes.
NTF slmTrapSysNameChange	1.3.6.1.4.1.4515.1.3.5.5			A slmTrapSysNameChange trap is sent when the value of the slmSysName is changed.
NTF slmTrapSysLocationChange	1.3.6.1.4.1.4515.1.3.5.6			A slmTrapSysLocationChange trap is sent when the value of the slmSysLocation is changed.
slmSyslogDestTable	1.3.6.1.4.1.4515.1.3.5.7		not-accessible	A list of syslog destination entries.
slmSyslogDestEntry	1.3.6.1.4.1.4515.1.3.5.7.1		not-accessible	This entry includes a destination IP addresses to which to send log messages.
I32 slmSyslogDestAddress	1.3.6.1.4.1.4515.1.3.5.7.1.1	Integer32	read-create	A copy of slmSyslogDestTable represented as an integer. Needed due to VxWorks failure to handle an ip address as a table index.
ROW slmSyslogDestRowStatus	1.3.6.1.4.1.4515.1.3.5.7.1.2	RowStatus	read-create	This object is used to create and delete rows in the slmSyslogDestTable.
INT slmSyslogLevel	1.3.6.1.4.1.4515.1.3.5.7.1.3	INTEGER	read-create	The level of log messages which this manager expects to receive.
INT slmSyslogPort	1.3.6.1.4.1.4515.1.3.5.7.1.4	INTEGER	read-create	The destination port for to send the log message. The default value is 514.
IP slmSyslogDestIpAddress	1.3.6.1.4.1.4515.1.3.5.7.1.5	IpAddress	read-create	The address to send log messages on behalf of this entry.
slmLogFile	1.3.6.1.4.1.4515.1.3.8
slmConfigFile	1.3.6.1.4.1.4515.1.3.9
slmChPass	1.3.6.1.4.1.4515.1.3.12
slmChPassTable	1.3.6.1.4.1.4515.1.3.12.1		not-accessible	The table is used for changing the user passowrd.
slmChPassEntry	1.3.6.1.4.1.4515.1.3.12.1.1		not-accessible	The entry is used to set the slmChPassNewPass. Note that the table contains no data, and when using GetNext it apears to be empty. To change the password, the NMS should issue a SET command with the new password while the two indexes equal to the old user login and password.
USE slmChPassLogin	1.3.6.1.4.1.4515.1.3.12.1.1.1	UserLogin	not-accessible	The user login.
USE slmChPassOldPass	1.3.6.1.4.1.4515.1.3.12.1.1.2	UserPassword	not-accessible	The user password.
USE slmChPassNewPass	1.3.6.1.4.1.4515.1.3.12.1.1.3	UserPassword	read-write	The user password.
slmLicense	1.3.6.1.4.1.4515.1.3.17
slmLicenseTable	1.3.6.1.4.1.4515.1.3.17.1		not-accessible	A list of License entries.
slmLicenseEntry	1.3.6.1.4.1.4515.1.3.17.1.1		not-accessible	An entry in the table correspond to installed license.
INT slmLicenseIndex	1.3.6.1.4.1.4515.1.3.17.1.1.1	INTEGER	read-only	The license index.
INT slmLicenseExpiration	1.3.6.1.4.1.4515.1.3.17.1.1.2	INTEGER	read-only	The number of seconds to expiration. Value -1 for permanent.
STR slmLicenseId	1.3.6.1.4.1.4515.1.3.17.1.1.3	DisplayString	read-only	The license text

RFC description

Main MIB module for Spirent LoadBlazer network testing equipment, providing SNMP management and monitoring capabilities.

Start monitoring SmartOptics SiteLight optical transport main control card/chassis (system/alarm/software-version status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SL-MAIN-MIB