DataAire-dap4-al-MIB

All MIBs › DataAire-dap4-al-MIB

Organization: Data Aire

Last Updated: 2011-07-12

Description: DataAire-dap4-al-MIB module

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DataAire-dap4-al-MIB?

DataAire-dap4-al-MIB is a vendor MIB generated by Data Aire for its dap4_al precision air conditioning controller; notably, its OID root sits under the Carel enterprise number (enterprises.9839, carel/systm) rather than a Data Aire-specific enterprise number, indicating the dap4_al unit is built on an OEM Carel pCO embedded controller platform that Data Aire integrates into its CRAC (computer room air conditioner) products. It exposes agentRelease/agentCode and pCOId1-Status/pCOId1-ErrorsNumber for the controller's own software health, alongside dozens of individually-named scalar objects for HVAC operating modes (dehum-on, hum-on, engy-on, cool-inhibit, heat-held) and alarm points covering mechanical and environmental faults — floor-wtr-alm, air-flow-alm, filter-alm, humidifier-alm, compressor high/low pressure (c1-hp-alm/c1-lp-alm, c2-hp-alm/c2-lp-alm), smoke-alm, wtr-flow-alm, and temperature/humidity out-of-range alarms (ra-tmp-hi-alm/lo-alm, hum-hi-alm/lo-alm). This flat but extensive alarm-point layout lets a building-management or NOC system detect specific environmental faults (a failed filter versus a refrigerant pressure fault versus a water-flow problem) in a data-center or equipment-room cooling unit rather than just a generic 'unit fault' state. It depends on SNMPv2-MIB for sysContact/sysName/sysLocation context and has no table structures of its own. Facilities engineers managing Data Aire CRAC units can download the DataAire-dap4-al-MIB file to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DataAire-dap4-al-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Data Aire dap4_al precision air conditioning (CRAC) controller, built on a Carel pCO OEM control platform

Monitoring Examples

An operator polls c1-hp-alm and c1-lp-alm alongside ra-tmp-hi-alm for a dap4_al unit; a c1-hp-alm (compressor 1 high-pressure alarm) asserting together with a rising return-air temperature indicates the refrigeration circuit has faulted and the unit is losing cooling capacity.

What Can Be Monitored

compressor high/low pressure alarms
filter, humidifier, and airflow alarm points
return-air/discharge-air temperature and humidity out-of-range alarms
controller firmware/agent release and internal error count
operating mode flags (dehumidify, humidify, energy-save, cooling/heating inhibit)

Imported Objects

From SNMPv2-CONF

OBJECT-GROUP

From SNMPv2-MIB

sysContact	OBJECT-TYPE
sysLocation	OBJECT-TYPE
sysName	OBJECT-TYPE

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE
enterprises

OIDs

OID symbolic	OID numeric	Type	Access	Description
carel	1.3.6.1.4.1.9839
systm	1.3.6.1.4.1.9839.1
I32 agentRelease	1.3.6.1.4.1.9839.1.1	Integer32	read-only	Release of the Agent.
I32 agentCode	1.3.6.1.4.1.9839.1.2	Integer32	read-only	Code of the Agent. 2=pCOWeb.
instruments	1.3.6.1.4.1.9839.2
pCOWebInfo	1.3.6.1.4.1.9839.2.0
pCOStatusgroup	1.3.6.1.4.1.9839.2.0.10
I32 pCOId1_Status	1.3.6.1.4.1.9839.2.0.10.1	Integer32	read-only	Status of pCOId1. 0=Offline, 1=Init, 2=Online
pCOErrorsNumbergroup	1.3.6.1.4.1.9839.2.0.11
I32 pCOId1_ErrorsNumber	1.3.6.1.4.1.9839.2.0.11.1	Integer32	read-only	Number of Communication Errors from pCOId1 to pCOWeb.
dap4_alMIB	1.3.6.1.4.1.9839.2.1			This is the MIB module for the dap4_al device.
digitalObjects	1.3.6.1.4.1.9839.2.1.1
I32 dehum_on	1.3.6.1.4.1.9839.2.1.1.1	Integer32	read-only	Dehumidify mode is running
I32 hum_on	1.3.6.1.4.1.9839.2.1.1.2	Integer32	read-only	Humidifier is running
I32 engy_on	1.3.6.1.4.1.9839.2.1.1.3	Integer32	read-only	Energy saver is running
I32 cool_inhibit	1.3.6.1.4.1.9839.2.1.1.4	Integer32	read-only	Cooling inhibit from Zone Master
I32 heat_held	1.3.6.1.4.1.9839.2.1.1.5	Integer32	read-only	Heat inhibited due to alarm condition
I32 humidifier_inhibit	1.3.6.1.4.1.9839.2.1.1.6	Integer32	read-only	Humidifier stopped due to alarm
I32 dehum_inhibit	1.3.6.1.4.1.9839.2.1.1.7	Integer32	read-only	Dehum is inhibited
I32 rht_during_dehum	1.3.6.1.4.1.9839.2.1.1.8	Integer32	read-only	reheat during dehum
I32 floor_wtr_alm	1.3.6.1.4.1.9839.2.1.1.9	Integer32	read-only	Water under floor alarm
I32 air_flow_alm	1.3.6.1.4.1.9839.2.1.1.10	Integer32	read-only	No air flow alarm
I32 filter_alm	1.3.6.1.4.1.9839.2.1.1.11	Integer32	read-only	Dirty filter from digital input
I32 humidifier_alm	1.3.6.1.4.1.9839.2.1.1.12	Integer32	read-only	Alarm from humidifier digital input
I32 firestat_alm	1.3.6.1.4.1.9839.2.1.1.13	Integer32	read-only	Temperature of return air above firestat alarm set point
I32 shortcycle_alm	1.3.6.1.4.1.9839.2.1.1.14	Integer32	read-only	One or more comps has short cycled
I32 humidity_fail	1.3.6.1.4.1.9839.2.1.1.15	Integer32	read-only	Sensor is out of range
I32 ret_air_fail	1.3.6.1.4.1.9839.2.1.1.16	Integer32	read-only	Sensor is out of range
I32 maint_alm	1.3.6.1.4.1.9839.2.1.1.17	Integer32	read-only	Maintenance Schedule Due alarm
I32 c1_hp_alm	1.3.6.1.4.1.9839.2.1.1.18	Integer32	read-only	High pressure alarm
I32 c1_lp_alm	1.3.6.1.4.1.9839.2.1.1.19	Integer32	read-only	Low pressure alarm
I32 c2_hp_alm	1.3.6.1.4.1.9839.2.1.1.20	Integer32	read-only	High pressure alarm
I32 c2_lp_alm	1.3.6.1.4.1.9839.2.1.1.21	Integer32	read-only	Low pressure alarm
I32 smoke_alm	1.3.6.1.4.1.9839.2.1.1.22	Integer32	read-only	Smoke detected from digital input
I32 wtr_flow_alm	1.3.6.1.4.1.9839.2.1.1.23	Integer32	read-only	No water flow alarm
I32 disch_air_fail	1.3.6.1.4.1.9839.2.1.1.24	Integer32	read-only	Sensor is out of range
I32 ra_tmp_hi_alm	1.3.6.1.4.1.9839.2.1.1.25	Integer32	read-only	Temperature of return air above alarm set point
I32 ra_tmp_lo_alm	1.3.6.1.4.1.9839.2.1.1.26	Integer32	read-only	Temperature of return air below alarm set point
I32 hum_hi_alm	1.3.6.1.4.1.9839.2.1.1.27	Integer32	read-only	Humidity above alarm set point
I32 hum_lo_alm	1.3.6.1.4.1.9839.2.1.1.28	Integer32	read-only	Humidity below alarm set point
I32 fan_overload	1.3.6.1.4.1.9839.2.1.1.29	Integer32	read-only	Fan overload
I32 stdby_pump_on	1.3.6.1.4.1.9839.2.1.1.30	Integer32	read-only	Standby pump on: Check primary pump -Optional alarm. Pump failure input signal required
I32 cust_msg_sw1	1.3.6.1.4.1.9839.2.1.1.31	Integer32	read-only	Custom alarm #1 -Optional alarm. External alarm input required. Factory programmed custom message required
I32 cust_msg_sw2	1.3.6.1.4.1.9839.2.1.1.32	Integer32	read-only	Custom alarm #2 -Optional alarm. External alarm input required. Factory programmed custom message required
I32 cust_msg_sw3	1.3.6.1.4.1.9839.2.1.1.33	Integer32	read-only	Custom alarm #3 -Optional alarm. External alarm input required. Factory programmed custom message required
I32 cust_msg_sw4	1.3.6.1.4.1.9839.2.1.1.34	Integer32	read-only	Custom alarm #4 -Optional alarm. External alarm input required. Factory programmed custom message required
I32 humsw_inhibit	1.3.6.1.4.1.9839.2.1.1.35	Integer32	read-only	Humidifier stopped due to custom alarm switch
I32 heat_inhibit	1.3.6.1.4.1.9839.2.1.1.36	Integer32	read-only	Heat inhibited due to custom switch alarm condition
I32 rht_hum_inhibit	1.3.6.1.4.1.9839.2.1.1.37	Integer32	read-only	Reheat and humidification inhibited from operation
I32 disch_tmp_lo_alm	1.3.6.1.4.1.9839.2.1.1.38	Integer32	read-only	Temperature of discharge air below alarm set point
I32 override_alm	1.3.6.1.4.1.9839.2.1.1.39	Integer32	read-only	Manual override: Check bypass switches - Standard alarm. Manual override switch is on
I32 condensation_alm	1.3.6.1.4.1.9839.2.1.1.40	Integer32	read-only	High condensation from digital input
I32 unit_in_standby	1.3.6.1.4.1.9839.2.1.1.41	Integer32	read-only	Unit in standby, all functions held off - Optional alarm. Control input signal required Factory setting required
I32 cw_sns_fail	1.3.6.1.4.1.9839.2.1.1.42	Integer32	read-only	Sensor is out of range
I32 humsw_chk_cyl	1.3.6.1.4.1.9839.2.1.1.43	Integer32	read-only	Humidifier stopped due to custom alarm switch
I32 bms_cooling_inhibit	1.3.6.1.4.1.9839.2.1.1.44	Integer32	read-write	Cooling operation inhibited by BMS
I32 bms_heat_inhibit	1.3.6.1.4.1.9839.2.1.1.45	Integer32	read-write	Heat inhibited due to bms
I32 bms_humidifier_inhibit	1.3.6.1.4.1.9839.2.1.1.46	Integer32	read-write	Humidifier operation inhibited by BMS
I32 bms_dehum_inhibit	1.3.6.1.4.1.9839.2.1.1.47	Integer32	read-write	Dehumidify mode inhibited by bms
I32 fan_inhibit_bms	1.3.6.1.4.1.9839.2.1.1.48	Integer32	read-write	Inhibit fan by bms
I32 hum_expect	1.3.6.1.4.1.9839.2.1.1.49	Integer32	read-only	Reduces control humidity cycling
I32 usashr_f_c	1.3.6.1.4.1.9839.2.1.1.50	Integer32	read-write	Temperature Mode 0=_C 1=_F
I32 lead_comp	1.3.6.1.4.1.9839.2.1.1.52	Integer32	read-only	Lead compressor select 0= C1, 1= C2
I32 wtrvlv_dir	1.3.6.1.4.1.9839.2.1.1.53	Integer32	read-only	Water valve direct or reverse acting
I32 ups_on_alm	1.3.6.1.4.1.9839.2.1.1.54	Integer32	read-only	Alarm: UPS power on: Check main power -Optional alarm. External alarm input required
I32 pwrup_alm	1.3.6.1.4.1.9839.2.1.1.55	Integer32	read-only	Loss of power requires manual reset of alarm
I32 seetag_cust_alm1	1.3.6.1.4.1.9839.2.1.1.56	Integer32	read-only	Local alarm #1: See tag inside door =Optional alarm. External alarm input required
I32 seetag_cust_alm2	1.3.6.1.4.1.9839.2.1.1.57	Integer32	read-only	Local alarm #2: See tag inside door =Optional alarm. External alarm input required
I32 seetag_cust_alm3	1.3.6.1.4.1.9839.2.1.1.58	Integer32	read-only	Local alarm #3: See tag inside door =Optional alarm. External alarm input required
I32 seetag_cust_alm4	1.3.6.1.4.1.9839.2.1.1.59	Integer32	read-only	Local alarm #4: See tag inside door =Optional alarm. External alarm input required
I32 shortcycle_alm_en	1.3.6.1.4.1.9839.2.1.1.60	Integer32	read-only	Enable short cycle alarm of the compressors
I32 superv_off	1.3.6.1.4.1.9839.2.1.1.61	Integer32	read-only	Supervisor (BMS) On-Off. Show the state OFFbyBMS in main mask (1: Off; 0: On
I32 bms_heartbeat	1.3.6.1.4.1.9839.2.1.1.62	Integer32	read-only	Bms heartbeat - pCO looks for update every 10 minutes
analogObjects	1.3.6.1.4.1.9839.2.1.2
I32 ret_air_tmp	1.3.6.1.4.1.9839.2.1.2.1	Integer32	read-only	Temperature of return air
I32 minmax_24hr_retair_maximum	1.3.6.1.4.1.9839.2.1.2.2	Integer32	read-only	Maximum Return air temp in last 24hrs
I32 minmax_24hr_retair_minumum	1.3.6.1.4.1.9839.2.1.2.3	Integer32	read-only	Minimum Return air temp in last 24hrs
I32 temp_setpoint	1.3.6.1.4.1.9839.2.1.2.4	Integer32	read-write	Temperature setpoint
I32 temp_deadband	1.3.6.1.4.1.9839.2.1.2.5	Integer32	read-write	Amount from setpoint before a comp is staged on
I32 humidity_ain_offs	1.3.6.1.4.1.9839.2.1.2.6	Integer32	read-only	Humidity Sensor Calibration
I32 return_ain_offs	1.3.6.1.4.1.9839.2.1.2.7	Integer32	read-only	Return Temperature Sensor Calibration
I32 cw_tmp	1.3.6.1.4.1.9839.2.1.2.8	Integer32	read-only	Temperature of chilled water
I32 disch_air_tmp	1.3.6.1.4.1.9839.2.1.2.9	Integer32	read-only	Temperature of discharge air
I32 discharge_ain_offs	1.3.6.1.4.1.9839.2.1.2.10	Integer32	read-only	Discharge Temperature Sensor Calibration - Optional discharge air temperature sensor required (B9)
I32 cw_ain_offs	1.3.6.1.4.1.9839.2.1.2.11	Integer32	read-only	Chilled Water Temperature Sensor Calibration - Optional chilled water temperature sensor required (B10)
I32 engsaver_setpoint	1.3.6.1.4.1.9839.2.1.2.12	Integer32	read-write	Temperature setpoint where chilled water will is requested
I32 opt1_analog	1.3.6.1.4.1.9839.2.1.2.13	Integer32	read-only	Value of the analog input
I32 opt2_analog	1.3.6.1.4.1.9839.2.1.2.14	Integer32	read-only	Value of the analog input
I32 opt3_analog	1.3.6.1.4.1.9839.2.1.2.15	Integer32	read-only	Value of the analog input
I32 opt4_analog	1.3.6.1.4.1.9839.2.1.2.16	Integer32	read-only	Value of the analog input
I32 opt_sns_1_y1	1.3.6.1.4.1.9839.2.1.2.17	Integer32	read-only	Analog Sensor 1 Minimum Value
I32 opt_sns_1_y2	1.3.6.1.4.1.9839.2.1.2.18	Integer32	read-only	Analog Sensor 1 Maximum Value
I32 opt_sns_1_ain_offs	1.3.6.1.4.1.9839.2.1.2.19	Integer32	read-only	Analog Sensor 1 Calibration
I32 opt_sns_2_y1	1.3.6.1.4.1.9839.2.1.2.20	Integer32	read-only	Analog Sensor 2 Minimum Value
I32 opt_sns_2_y2	1.3.6.1.4.1.9839.2.1.2.21	Integer32	read-only	Analog Sensor 2 Maximum Value
I32 opt_sns_2_ain_offs	1.3.6.1.4.1.9839.2.1.2.22	Integer32	read-only	Analog Sensor 2 Calibration
I32 opt_sns_3_y1	1.3.6.1.4.1.9839.2.1.2.23	Integer32	read-only	Analog Sensor 3 Minimum Value
I32 opt_sns_3_y2	1.3.6.1.4.1.9839.2.1.2.24	Integer32	read-only	Analog Sensor 3 Maximum Value
I32 opt_sns_3_ain_offs	1.3.6.1.4.1.9839.2.1.2.25	Integer32	read-only	Analog Sensor 3 Calibration
I32 opt_sns_4_y1	1.3.6.1.4.1.9839.2.1.2.26	Integer32	read-only	Analog Sensor 4 Minimum Value
I32 opt_sns_4_y2	1.3.6.1.4.1.9839.2.1.2.27	Integer32	read-only	Analog Sensor 4 Maximum Value
I32 opt_sns_4_ain_offs	1.3.6.1.4.1.9839.2.1.2.28	Integer32	read-only	Analog Sensor 4 Calibration
integerObjects	1.3.6.1.4.1.9839.2.1.3
I32 disch_air_lo_sp	1.3.6.1.4.1.9839.2.1.3.1	Integer32	read-write	Lower Limit alarm of discharge air temp
I32 humidity_dis	1.3.6.1.4.1.9839.2.1.3.2	Integer32	read-only	Relative humidity displayed as xx%
I32 stages_on	1.3.6.1.4.1.9839.2.1.3.3	Integer32	read-only	Cooling Stages On, DX only
I32 heaters_on	1.3.6.1.4.1.9839.2.1.3.4	Integer32	read-only	Number of heat stages running
I32 minmax_24hr_hum_maximum	1.3.6.1.4.1.9839.2.1.3.5	Integer32	read-only	Maximum humidity in last 24hrs
I32 minmax_24hr_hum_minumum	1.3.6.1.4.1.9839.2.1.3.6	Integer32	read-only	Minimum humidity in last 24hrs
I32 comp_duty	1.3.6.1.4.1.9839.2.1.3.7	Integer32	read-only	Cooling Utilization Over Last Hour -Percentage of cooling is used in the last hour of operation; this point applies to DX unit.
I32 heat_duty	1.3.6.1.4.1.9839.2.1.3.8	Integer32	read-only	Heating Utilization Over Last Hour -Percentage of heating is used in the last hour of operation
I32 hum_duty	1.3.6.1.4.1.9839.2.1.3.9	Integer32	read-only	Humidifier Utilization Over Last Hour -Percentage of humidifier is used in the last hour of operation
I32 c1_hours_h	1.3.6.1.4.1.9839.2.1.3.10	Integer32	read-only	Compressor 1 Runtime -This point applies to DX unit with one compressor -high
I32 c1_hours_l	1.3.6.1.4.1.9839.2.1.3.11	Integer32	read-only	Compressor 1 Runtime -This point applies to DX unit with one compressor -low
I32 c2_hours_h	1.3.6.1.4.1.9839.2.1.3.12	Integer32	read-only	Compressor 2 Runtime -This point applies to DX unit with dual compressor - high
I32 c2_hours_l	1.3.6.1.4.1.9839.2.1.3.13	Integer32	read-only	Compressor 2 Runtime -This point applies to DX unit with dual compressor - low
I32 ht1_hours_h	1.3.6.1.4.1.9839.2.1.3.14	Integer32	read-only	Heater 1 Runtime - high
I32 ht1_hours_l	1.3.6.1.4.1.9839.2.1.3.15	Integer32	read-only	Heater 1 Runtime - low
I32 current_second	1.3.6.1.4.1.9839.2.1.3.16	Integer32	read-only	Current second
I32 current_minute	1.3.6.1.4.1.9839.2.1.3.17	Integer32	read-only	Current minute
I32 current_hour	1.3.6.1.4.1.9839.2.1.3.18	Integer32	read-only	Current hour
I32 current_day	1.3.6.1.4.1.9839.2.1.3.19	Integer32	read-only	Current day
I32 current_month	1.3.6.1.4.1.9839.2.1.3.20	Integer32	read-only	Current month
I32 current_year	1.3.6.1.4.1.9839.2.1.3.21	Integer32	read-only	Current year
I32 firestat_sp	1.3.6.1.4.1.9839.2.1.3.22	Integer32	read-write	Alarm settting of return air temp to determine there is a fire
I32 hum_hi_sp	1.3.6.1.4.1.9839.2.1.3.23	Integer32	read-write	Humidity upper limit alarm
I32 ret_air_hi_sp	1.3.6.1.4.1.9839.2.1.3.24	Integer32	read-write	Upper limit alarm of return air temp
I32 hum_lo_sp	1.3.6.1.4.1.9839.2.1.3.25	Integer32	read-write	Humidity lower limit alarm
I32 ret_air_lo_sp	1.3.6.1.4.1.9839.2.1.3.26	Integer32	read-write	Lower limit alarm of return air temp
I32 hum_deadband	1.3.6.1.4.1.9839.2.1.3.27	Integer32	read-write	amount hum must change from setpoint before acting
I32 hum_setpoint	1.3.6.1.4.1.9839.2.1.3.28	Integer32	read-write	humidity setpoint
I32 start_dly	1.3.6.1.4.1.9839.2.1.3.29	Integer32	read-write	Time before the system starts up
I32 alm1_del	1.3.6.1.4.1.9839.2.1.3.30	Integer32	read-only	Optional Alarm 1 Delay
I32 alm2_del	1.3.6.1.4.1.9839.2.1.3.31	Integer32	read-only	Optional Alarm 2 Delay
I32 alm3_del	1.3.6.1.4.1.9839.2.1.3.32	Integer32	read-only	Optional Alarm 3 Delay
I32 alarm1_txt	1.3.6.1.4.1.9839.2.1.3.33	Integer32	read-only	Message on optional alarm screen, some also add function
I32 alarm2_txt	1.3.6.1.4.1.9839.2.1.3.34	Integer32	read-only	Message on optional alarm screen, some also add function
I32 alarm3_txt	1.3.6.1.4.1.9839.2.1.3.35	Integer32	read-only	Message on optional alarm screen, some also add function
I32 alarm4_txt	1.3.6.1.4.1.9839.2.1.3.36	Integer32	read-only	Message on optional alarm screen, some also add function
I32 comp_sel	1.3.6.1.4.1.9839.2.1.3.37	Integer32	read-only	Comps 0=none, 1=one, 2=one+UL, 3=two, 4=two+UL, 5=Four/two circuit
I32 dehum_mode	1.3.6.1.4.1.9839.2.1.3.38	Integer32	read-only	0=none, 1= comp limited, 2=twocomp limited, 3= comp unlimited, 4=twocomp unlimited
I32 reheat_sel	1.3.6.1.4.1.9839.2.1.3.39	Integer32	read-only	Number of heat stages
I32 hum_sel	1.3.6.1.4.1.9839.2.1.3.40	Integer32	read-only	0=none, 1=comp mod, 2=comp non, 3= comf mod, 4= conf non mod
I32 alm_contact_msg	1.3.6.1.4.1.9839.2.1.3.41	Integer32	read-only	Text displayed on all alarm screens
I32 powerup_sel	1.3.6.1.4.1.9839.2.1.3.42	Integer32	read-only	0= start wo/alarm, 1= start w/alarm, 2= requires reset of alarm
I32 buzzer_select	1.3.6.1.4.1.9839.2.1.3.43	Integer32	read-only	0=None, 1=short beeps, 2=long beep, 3=Constant
I32 cw_disp	1.3.6.1.4.1.9839.2.1.3.44	Integer32	read-only	% of 10volts of analog output #1
I32 wtrvlv_duty	1.3.6.1.4.1.9839.2.1.3.45	Integer32	read-only	Chilled Water Utilization Over Last Hour - This applies to Chilled water or Energy saver units.
I32 hum_hours_h	1.3.6.1.4.1.9839.2.1.3.46	Integer32	read-only	Humidifier Runtime - high
I32 hum_hours_l	1.3.6.1.4.1.9839.2.1.3.47	Integer32	read-only	Humidifier Runtime - low
I32 blower_hours_h	1.3.6.1.4.1.9839.2.1.3.48	Integer32	read-only	Blower Runtime - high
I32 blower_hours_l	1.3.6.1.4.1.9839.2.1.3.49	Integer32	read-only	Blower Runtime - low
I32 alm4_del	1.3.6.1.4.1.9839.2.1.3.50	Integer32	read-only	Optional Alarm 4 Delay
I32 assist_sel	1.3.6.1.4.1.9839.2.1.3.51	Integer32	read-only	0= no comp assist, 1=one comp assist, 2= two comp assist, 3... 4...
I32 wtrvlv_sel	1.3.6.1.4.1.9839.2.1.3.52	Integer32	read-only	Water valve type 0=none, 1=chill, 2=Engy, 3=Aux chill, 4=Disc Reg
I32 wtrvlv_volts_sel	1.3.6.1.4.1.9839.2.1.3.53	Integer32	read-only	Water valve voltage 0= 0-10, 1=2-10, 2=7-10, 3=6-9, 4=4-7
I32 hum_volts	1.3.6.1.4.1.9839.2.1.3.54	Integer32	read-only	% of 10volts of analog output #2
I32 dehum_hours_h	1.3.6.1.4.1.9839.2.1.3.55	Integer32	read-only	Dehumidifier Runtime - High
I32 dehum_hours_l	1.3.6.1.4.1.9839.2.1.3.56	Integer32	read-only	Dehumidifier Runtime - Low
I32 autoflush_dly	1.3.6.1.4.1.9839.2.1.3.58	Integer32	read-only	Time between drain cycles 0=12hr, 1=24hr, 2=48hr, 3=96hr, 4=None
I32 y4_out	1.3.6.1.4.1.9839.2.1.3.59	Integer32	read-only	Value sent to optional analog output#1
I32 y5_out	1.3.6.1.4.1.9839.2.1.3.60	Integer32	read-only	Value sent to optional analog output#2
I32 air_flow	1.3.6.1.4.1.9839.2.1.3.61	Integer32	read-only	Current Fan Airflow - Based on calculated Pressure Diff formula
I32 opt_snsr1_name	1.3.6.1.4.1.9839.2.1.3.62	Integer32	read-only	Name of the sensor
I32 opt_sns_1_ain_type	1.3.6.1.4.1.9839.2.1.3.63	Integer32	read-only	Analog Sensor 1 Type {0=NTC 1=PT1000 2=0-1VDC 3=0-10VDC 4=4-20mA 5=ON/OFF 6=0-5VDC 7=NTC HT 8=-50T90 9=10T170}
I32 opt_snsr2_name	1.3.6.1.4.1.9839.2.1.3.64	Integer32	read-only	Name of the sensor
I32 opt_sns_2_ain_type	1.3.6.1.4.1.9839.2.1.3.65	Integer32	read-only	Analog Sensor 2 Type {0=NTC 1=PT1000 2=0-1VDC 3=0-10VDC 4=4-20mA 5=ON/OFF 6=0-5VDC 7=NTC HT 8=-50T90 9=10T170}
I32 opt_snsr3_name	1.3.6.1.4.1.9839.2.1.3.66	Integer32	read-only	Name of the sensor
I32 opt_sns_3_ain_type	1.3.6.1.4.1.9839.2.1.3.67	Integer32	read-only	Analog Sensor 3 Type {0=NTC 1=PT1000 2=0-1VDC 3=0-10VDC 4=4-20mA 5=ON/OFF 6=0-5VDC 7=NTC HT 8=-50T90 9=10T170}
I32 opt_snsr4_name	1.3.6.1.4.1.9839.2.1.3.68	Integer32	read-only	Name of the sensor
I32 opt_sns_4_ain_type	1.3.6.1.4.1.9839.2.1.3.69	Integer32	read-only	Analog Sensor 4 Type {0=NTC 1=PT1000 2=0-1VDC 3=0-10VDC 4=4-20mA 5=ON/OFF 6=0-5VDC 7=NTC HT 8=-50T90 9=10T170}
I32 cw_fan_speed_bms	1.3.6.1.4.1.9839.2.1.3.70	Integer32	read-write	CW Fan speed (%) sent via BMS
I32 dx_fan_speed_bms	1.3.6.1.4.1.9839.2.1.3.71	Integer32	read-write	DX Fan speed (%) sent via BMS
I32 fan_speed_max	1.3.6.1.4.1.9839.2.1.3.72	Integer32	read-write	Maximum Fan speed (% of output) modulation.
I32 fan_speed_min	1.3.6.1.4.1.9839.2.1.3.73	Integer32	read-write	Minimum Fan speed (% of output) modulation from pressure.
I32 fan_pr_sp	1.3.6.1.4.1.9839.2.1.3.74	Integer32	read-write	Fan pressure setpoint (0.01 inches of water)
I32 fan_pr_band	1.3.6.1.4.1.9839.2.1.3.75	Integer32	read-write	Fan pressure band (0.01 inches of water)
I32 fan_af_max	1.3.6.1.4.1.9839.2.1.3.76	Integer32	read-write	Maximum air flow limit of setpoint from BMS or valve modulation.
I32 fan_af_min	1.3.6.1.4.1.9839.2.1.3.77	Integer32	read-write	Minimum air flow limit of setpoint from BMS or valve modulation.
I32 fan_kfactor	1.3.6.1.4.1.9839.2.1.3.78	Integer32	read-write	Fan K Factor
I32 num_fans	1.3.6.1.4.1.9839.2.1.3.79	Integer32	read-write	Number of fans installed in this unit
I32 ht2_hours_h	1.3.6.1.4.1.9839.2.1.3.81	Integer32	read-only	Heater 2 Runtime - high
I32 ht2_hours_l	1.3.6.1.4.1.9839.2.1.3.82	Integer32	read-only	Heater 2 Runtime - low
I32 ht3_hours_h	1.3.6.1.4.1.9839.2.1.3.83	Integer32	read-only	Heater 3 Runtime - high
I32 ht3_hours_l	1.3.6.1.4.1.9839.2.1.3.84	Integer32	read-only	Heater 3 Runtime - low
I32 engy_hours_h	1.3.6.1.4.1.9839.2.1.3.85	Integer32	read-only	Energy Saver Runtime - This optional point applies to energy saver units only -high
I32 engy_hours_l	1.3.6.1.4.1.9839.2.1.3.86	Integer32	read-only	Energy Saver Runtime - This optional point applies to energy saver units only - low
I32 cw_hours_h	1.3.6.1.4.1.9839.2.1.3.87	Integer32	read-only	Chilled Water Runtime - This applies to chilled water units only - high
I32 cw_hours_l	1.3.6.1.4.1.9839.2.1.3.88	Integer32	read-only	Chilled Water Runtime - This applies to chilled water units only - low
I32 c3_hours_h	1.3.6.1.4.1.9839.2.1.3.89	Integer32	read-only	Compressor 3 Runtime - This applies when unit has four stages tandem compressors - high
I32 c3_hours_l	1.3.6.1.4.1.9839.2.1.3.90	Integer32	read-only	Compressor 3 Runtime - This applies when unit has four stages tandem compressors - low
I32 c4_hours_l	1.3.6.1.4.1.9839.2.1.3.91	Integer32	read-only	Compressor 4 Runtime - This applies when unit has four stages tandem compressors. - high
I32 c4_hours_h	1.3.6.1.4.1.9839.2.1.3.92	Integer32	read-only	Compressor 4 Runtime - This applies when unit has four stages tandem compressors. - low
I32 cond_hours_h	1.3.6.1.4.1.9839.2.1.3.93	Integer32	read-only	Condenser Runtime - high
I32 cond_hours_l	1.3.6.1.4.1.9839.2.1.3.94	Integer32	read-only	Condenser Runtime - low
I32 dx_fan_speed	1.3.6.1.4.1.9839.2.1.3.95	Integer32	read-only	Fan speed (% of output) when compressor cooling.
I32 cw_fan_speed	1.3.6.1.4.1.9839.2.1.3.96	Integer32	read-only	Fan speed (% of output) when cold water cooling.
I32 fan_af_dx_sp	1.3.6.1.4.1.9839.2.1.3.97	Integer32	read-only	Fan air flow setpoint for DX unit (cfm)
I32 fan_af_cw_sp	1.3.6.1.4.1.9839.2.1.3.98	Integer32	read-only	Fan air flow setpoint for CW unit (cfm)
I32 zm_airflow_sp	1.3.6.1.4.1.9839.2.1.3.99	Integer32	read-write	Zone Airflow Setpoint kcfm

RFC description

Data Aire dap4_al device MIB for monitoring and controlling air conditioning and environmental systems.

Start monitoring Data Aire dap4_al precision air conditioning (CRAC) controller, Carel pCO platform with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DataAire-dap4-al-MIB

What Is DataAire-dap4-al-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description