PEA-TEST-IPDSLAM

All MIBs › PEA-TEST-IPDSLAM

Organization: Ericsson Diax A/S - Denmark

Last Updated: 2004-05-03

Category: DSL and Broadband

Description: Manages DSL line diagnostic test execution, result retrieval, and test-state objects on the Ericsson Diax IP DSLAM.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is PEA-TEST-IPDSLAM?

PEA-TEST-IPDSLAM is an Ericsson (via Diehl/Diax A/S, a Danish DSL-equipment maker acquired into Ericsson's broadband portfolio) proprietary MIB defining SELT (Single-Ended Line Test, loop qualification) and line-noise test control on IP-DSLAM equipment. Its objects cover a SELT-test input table, near-end/far-end noise-test activation, an advanced-output-table activation flag, tone profile, voice-over-parameters (Vop) setting, and upstream/downstream tone masks and transmit levels. As a diagnostic/configuration MIB it lets an administrator trigger a loop-qualification test on a DSL line and review its tone-mask/transmit-level parameters. It is deployed on Ericsson (Diax) IP-DSLAM broadband access equipment. Engineers can download the PEA-TEST-IPDSLAM file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in PEA-TEST-IPDSLAM. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ericsson (Diax) IP-DSLAM broadband access equipment

Monitoring Examples

An access-network technician triggers a SELT test via seltTestInputTable on a line reporting sync problems, to get a loop-qualification estimate before dispatching a technician to check the physical wiring.

What Can Be Monitored

SELT/noise test trigger and results
tone mask and transmit level configuration

Imported Objects

From DIESEL-SMI

peaIpDslam

OBJECT-IDENTITY

From PEA-BRIDGE-IPDSLAM

lineIndex	OBJECT-TYPE
pvcIndex	OBJECT-TYPE

From PEA-IF-IPDSLAM

adslIfTestError	OBJECT-TYPE
adslIfTestResult	OBJECT-TYPE
adslIfTestType	OBJECT-TYPE

From PEM-STANDARD

eventTime	OBJECT-TYPE
eventTypePem	OBJECT-TYPE
managedObjectClass	OBJECT-TYPE
managedObjectInstance	OBJECT-TYPE
perceivedSeverity	OBJECT-TYPE
probableCause	OBJECT-TYPE
sequenceNumber	OBJECT-TYPE

From SNMPv2-CONF

NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
peaTestIpDslam	1.3.6.1.4.1.193.72.300.20			In this module are defined the control entries for input and output data for SELT (loop qualification) and NOISE tests.
peaTestIpDslamObjects	1.3.6.1.4.1.193.72.300.20.1
seltTestInputTable	1.3.6.1.4.1.193.72.300.20.1.1		not-accessible	This table provides the input parameters for the SELT test.
seltTestInputEntry	1.3.6.1.4.1.193.72.300.20.1.1.1		not-accessible	An entry contains input parameters for the SELT test for the subscriber line identified by lineIndex.
INT seltNoiseNeAct	1.3.6.1.4.1.193.72.300.20.1.1.1.1	INTEGER	read-write	Value that indicates if Near-end noise should be measured or pre-selected. If the noise should be measured this should be Activated(1). If the noise should be pre-selected seltNoiseNeAct should be set to Deactivated(0).
INT seltNoiseFeAct	1.3.6.1.4.1.193.72.300.20.1.1.1.2	INTEGER	read-write	Value that indicates if Far-end noise should be measured or pre-selected. If the noise should be measured this should be Activated(1). If the noise should be pre-selected seltNoiseFeAct should be set to Deactivated(0).
INT seltAdvOutputTableAct	1.3.6.1.4.1.193.72.300.20.1.1.1.3	INTEGER	read-write	Switch that activates presentation of tone information or deactivates it.
INT seltToneProfile	1.3.6.1.4.1.193.72.300.20.1.1.1.8	INTEGER	read-write	Tone profile for different system configurations. The unused values for this parameter are reserved for comming standards or future proprietary techniques.
U32 seltVop	1.3.6.1.4.1.193.72.300.20.1.1.1.9	Unsigned32	read-write	Velocity of propagation is the speed at which an electric signal passes through a cable.
OCT seltUsToneMask	1.3.6.1.4.1.193.72.300.20.1.1.1.10	OCTET STRING	read-write	Upstream active tones assumed in capacity estimation. Using single bits in integer set specific tones on /off. Total number of tones is 256.
OCT seltDsToneMask	1.3.6.1.4.1.193.72.300.20.1.1.1.11	OCTET STRING	read-write	Downstream active tones assumed in capacity estimation. Using single bits in integer set specific tones on /off. Total number of tones is 512.
I32 seltUsTransmitLevel	1.3.6.1.4.1.193.72.300.20.1.1.1.12	Integer32	read-write	Upstream transmit level.
I32 seltDsTransmitLevel	1.3.6.1.4.1.193.72.300.20.1.1.1.13	Integer32	read-write	Downstream transmit level.
INT seltExtSplitterType	1.3.6.1.4.1.193.72.300.20.1.1.1.14	INTEGER	read-write	External splitter filter type. This parameter is used to inform the SELT software about any installed external splitter filter. The SELT performance is affected by this parameter. The unused values for this parameter are reserved for coming external splitter types or future proprietary options.
seltTestBasicOutputTable	1.3.6.1.4.1.193.72.300.20.1.3		not-accessible	This table provides the basic output parameters for the SELT test.
seltTestBasicOutputEntry	1.3.6.1.4.1.193.72.300.20.1.3.1		not-accessible	An entry contains the basic output parameters for the SELT test for the subscriber line identified by lineIndex.
U32 seltLength	1.3.6.1.4.1.193.72.300.20.1.3.1.1	Unsigned32	read-only	Loop length to termination.
U32 seltSingleAttVal	1.3.6.1.4.1.193.72.300.20.1.3.1.2	Unsigned32	read-only	Attenuation at 300kHz.
INT seltAdslDeployment	1.3.6.1.4.1.193.72.300.20.1.3.1.3	INTEGER	read-only	Parameter indicating the possibility for ADSL deployment. A value of Possible(0) indicates that the tested loop is possible for ADSL Deployment, Uncertain(1) indicates that it might be possible but some uncertainties exist. A value of NotPossible(2) indicates that ADSL deployment is not possible on the tested loop. Decision is based on parameters calculated in the selt algorithm.
U32 seltCapacityUs	1.3.6.1.4.1.193.72.300.20.1.3.1.4	Unsigned32	read-only	Total loop capacity in the upstream direction.
U32 seltCapacityDs	1.3.6.1.4.1.193.72.300.20.1.3.1.5	Unsigned32	read-only	Total loop capacity in the downstream direction.
INT seltTermination	1.3.6.1.4.1.193.72.300.20.1.3.1.6	INTEGER	read-only	Loop termination at customer side. The values between 6 and 254 are to be defined.
INT seltBasicReliability	1.3.6.1.4.1.193.72.300.20.1.3.1.7	INTEGER	read-only	Reliability of the parameters in the seltTestBasicOutputTable. The values between 7 and 255 are to be defined.
I32 seltUSMeanNoiseLevel	1.3.6.1.4.1.193.72.300.20.1.3.1.8	Integer32	read-only	The mean US noise level present on the line seen from IPDSLAM.
I32 seltDSMeanNoiseLevel	1.3.6.1.4.1.193.72.300.20.1.3.1.9	Integer32	read-only	The mean DS noise level present on the line seen from IPDSLAM.
U32 seltAttenLimit	1.3.6.1.4.1.193.72.300.20.1.3.1.10	Unsigned32	read-only	Reported maximum measurable/reliable attenuation @ 300 kHz.
seltTestAdvOutputTable	1.3.6.1.4.1.193.72.300.20.1.4		not-accessible	This table provides the advanced output parameters for the SELT test.
seltTestAdvOutputEntry	1.3.6.1.4.1.193.72.300.20.1.4.1		not-accessible	An entry contains the advanced output parameters for the SELT test for the subscriber line identified by lineIndex.
OCT seltEcho0	1.3.6.1.4.1.193.72.300.20.1.4.1.1	OCTET STRING	read-only	Magnitude of the Echo Frequency Response of the line. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltEcho1	1.3.6.1.4.1.193.72.300.20.1.4.1.2	OCTET STRING	read-only	Magnitude of the Echo Frequency Response of the line. Part 1. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltEcho2	1.3.6.1.4.1.193.72.300.20.1.4.1.3	OCTET STRING	read-only	Magnitude of the Echo Frequency Response of the line. Part 2. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltEcho3	1.3.6.1.4.1.193.72.300.20.1.4.1.4	OCTET STRING	read-only	Magnitude of the Echo Frequency Response of the line. Part 3. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltInsertionLoss0	1.3.6.1.4.1.193.72.300.20.1.4.1.5	OCTET STRING	read-only	Line Insertion loss (attenuation) per tone. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltInsertionLoss1	1.3.6.1.4.1.193.72.300.20.1.4.1.6	OCTET STRING	read-only	Line Insertion loss (attenuation) per tone. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltInsertionLoss2	1.3.6.1.4.1.193.72.300.20.1.4.1.7	OCTET STRING	read-only	Line Insertion loss (attenuation) per tone. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltInsertionLoss3	1.3.6.1.4.1.193.72.300.20.1.4.1.8	OCTET STRING	read-only	Line Insertion loss (attenuation) per tone. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltNoiseNe0	1.3.6.1.4.1.193.72.300.20.1.4.1.9	OCTET STRING	read-only	Near-end line noise per tone in Upstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltNoiseNe1	1.3.6.1.4.1.193.72.300.20.1.4.1.10	OCTET STRING	read-only	Near-end line noise per tone in Upstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltNoiseNe2	1.3.6.1.4.1.193.72.300.20.1.4.1.11	OCTET STRING	read-only	Near-end line noise per tone in Upstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltNoiseNe3	1.3.6.1.4.1.193.72.300.20.1.4.1.12	OCTET STRING	read-only	Near-end line noise per tone in Upstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltNoiseFe0	1.3.6.1.4.1.193.72.300.20.1.4.1.13	OCTET STRING	read-only	Far-end line noise per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltNoiseFe1	1.3.6.1.4.1.193.72.300.20.1.4.1.14	OCTET STRING	read-only	Far-end line noise per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltNoiseFe2	1.3.6.1.4.1.193.72.300.20.1.4.1.15	OCTET STRING	read-only	Far-end line noise per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltNoiseFe3	1.3.6.1.4.1.193.72.300.20.1.4.1.16	OCTET STRING	read-only	Far-end line noise per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltSnrNe0	1.3.6.1.4.1.193.72.300.20.1.4.1.17	OCTET STRING	read-only	Signal to Noise ration per tone in Upstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltSnrNe1	1.3.6.1.4.1.193.72.300.20.1.4.1.18	OCTET STRING	read-only	Signal to Noise ration per tone in Upstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltSnrNe2	1.3.6.1.4.1.193.72.300.20.1.4.1.19	OCTET STRING	read-only	Signal to Noise ration per tone in Upstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltSnrNe3	1.3.6.1.4.1.193.72.300.20.1.4.1.20	OCTET STRING	read-only	Signal to Noise ration per tone in Upstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltSnrFe0	1.3.6.1.4.1.193.72.300.20.1.4.1.21	OCTET STRING	read-only	Signal to Noise ration per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltSnrFe1	1.3.6.1.4.1.193.72.300.20.1.4.1.22	OCTET STRING	read-only	Signal to Noise ration per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltSnrFe2	1.3.6.1.4.1.193.72.300.20.1.4.1.23	OCTET STRING	read-only	Signal to Noise ration per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltSnrFe3	1.3.6.1.4.1.193.72.300.20.1.4.1.24	OCTET STRING	read-only	Signal to Noise ration per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltBitLoadingEstNe0	1.3.6.1.4.1.193.72.300.20.1.4.1.25	OCTET STRING	read-only	Estimate of the maximum attainable load of bits per tone in Upstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltBitLoadingEstNe1	1.3.6.1.4.1.193.72.300.20.1.4.1.26	OCTET STRING	read-only	Estimate of the maximum attainable load of bits per tone in Upstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltBitLoadingEstFe0	1.3.6.1.4.1.193.72.300.20.1.4.1.27	OCTET STRING	read-only	Estimate of the maximum attainable load of bits per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltBitLoadingEstFe1	1.3.6.1.4.1.193.72.300.20.1.4.1.28	OCTET STRING	read-only	Estimate of the maximum attainable load of bits per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltInsertionLoss4	1.3.6.1.4.1.193.72.300.20.1.4.1.29	OCTET STRING	read-only	Line Insertion loss (attenuation) per tone. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltInsertionLoss5	1.3.6.1.4.1.193.72.300.20.1.4.1.30	OCTET STRING	read-only	Line Insertion loss (attenuation) per tone. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltInsertionLoss6	1.3.6.1.4.1.193.72.300.20.1.4.1.31	OCTET STRING	read-only	Line Insertion loss (attenuation) per tone. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltInsertionLoss7	1.3.6.1.4.1.193.72.300.20.1.4.1.32	OCTET STRING	read-only	Line Insertion loss (attenuation) per tone. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltNoiseFe4	1.3.6.1.4.1.193.72.300.20.1.4.1.33	OCTET STRING	read-only	Far-end line noise per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltNoiseFe5	1.3.6.1.4.1.193.72.300.20.1.4.1.34	OCTET STRING	read-only	Far-end line noise per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltNoiseFe6	1.3.6.1.4.1.193.72.300.20.1.4.1.35	OCTET STRING	read-only	Far-end line noise per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltNoiseFe7	1.3.6.1.4.1.193.72.300.20.1.4.1.36	OCTET STRING	read-only	Far-end line noise per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltSnrFe4	1.3.6.1.4.1.193.72.300.20.1.4.1.37	OCTET STRING	read-only	Signal to Noise ration per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltSnrFe5	1.3.6.1.4.1.193.72.300.20.1.4.1.38	OCTET STRING	read-only	Signal to Noise ration per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltSnrFe6	1.3.6.1.4.1.193.72.300.20.1.4.1.39	OCTET STRING	read-only	Signal to Noise ration per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltSnrFe7	1.3.6.1.4.1.193.72.300.20.1.4.1.40	OCTET STRING	read-only	Signal to Noise ration per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltBitLoadingEstFe2	1.3.6.1.4.1.193.72.300.20.1.4.1.41	OCTET STRING	read-only	Estimate of the maximum attainable load of bits per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltBitLoadingEstFe3	1.3.6.1.4.1.193.72.300.20.1.4.1.42	OCTET STRING	read-only	Estimate of the maximum attainable load of bits per tone in Downstream band. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltTDR0	1.3.6.1.4.1.193.72.300.20.1.4.1.43	OCTET STRING	read-only	Time Domain Reflectometry (TDR) impulse diagram equivalent. Part 0. Consecutive values are spaced 1/(10244312.5) seconds in time. The value spacing can be interpretated in a length unit equal to [x meter], where x = 0.5seltVop100001/(1024*4312.5) corresponding to an one-way physical length fraction. seltVop is read/write available via seltTestInputEntry. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltTDR1	1.3.6.1.4.1.193.72.300.20.1.4.1.44	OCTET STRING	read-only	Time Domain Reflectometry (TDR) impulse diagram equivalent. Part 0. Consecutive values are spaced 1/(10244312.5) seconds in time. The value spacing can be interpretated in a length unit equal to [x meter], where x = 0.5seltVop100001/(1024*4312.5) corresponding to an one-way physical length fraction. seltVop is read/write available via seltTestInputEntry. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltTDR2	1.3.6.1.4.1.193.72.300.20.1.4.1.45	OCTET STRING	read-only	Time Domain Reflectometry (TDR) impulse diagram equivalent. Part 0. Consecutive values are spaced 1/(10244312.5) seconds in time. The value spacing can be interpretated in a length unit equal to [x meter], where x = 0.5seltVop100001/(1024*4312.5) corresponding to an one-way physical length fraction. seltVop is read/write available via seltTestInputEntry. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltTDR3	1.3.6.1.4.1.193.72.300.20.1.4.1.46	OCTET STRING	read-only	Time Domain Reflectometry (TDR) impulse diagram equivalent. Part 0. Consecutive values are spaced 1/(10244312.5) seconds in time. The value spacing can be interpretated in a length unit equal to [x meter], where x = 0.5seltVop100001/(1024*4312.5) corresponding to an one-way physical length fraction. seltVop is read/write available via seltTestInputEntry. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltTDR4	1.3.6.1.4.1.193.72.300.20.1.4.1.47	OCTET STRING	read-only	Time Domain Reflectometry (TDR) impulse diagram equivalent. Part 0. Consecutive values are spaced 1/(10244312.5) seconds in time. The value spacing can be interpretated in a length unit equal to [x meter], where x = 0.5seltVop100001/(1024*4312.5) corresponding to an one-way physical length fraction. seltVop is read/write available via seltTestInputEntry. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltTDR5	1.3.6.1.4.1.193.72.300.20.1.4.1.48	OCTET STRING	read-only	Time Domain Reflectometry (TDR) impulse diagram equivalent. Part 0. Consecutive values are spaced 1/(10244312.5) seconds in time. The value spacing can be interpretated in a length unit equal to [x meter], where x = 0.5seltVop100001/(1024*4312.5) corresponding to an one-way physical length fraction. seltVop is read/write available via seltTestInputEntry. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltTDR6	1.3.6.1.4.1.193.72.300.20.1.4.1.49	OCTET STRING	read-only	Time Domain Reflectometry (TDR) impulse diagram equivalent. Part 0. Consecutive values are spaced 1/(10244312.5) seconds in time. The value spacing can be interpretated in a length unit equal to [x meter], where x = 0.5seltVop100001/(1024*4312.5) corresponding to an one-way physical length fraction. seltVop is read/write available via seltTestInputEntry. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltTDR7	1.3.6.1.4.1.193.72.300.20.1.4.1.50	OCTET STRING	read-only	Time Domain Reflectometry (TDR) impulse diagram equivalent. Part 0. Consecutive values are spaced 1/(10244312.5) seconds in time. The value spacing can be interpretated in a length unit equal to [x meter], where x = 0.5seltVop100001/(1024*4312.5) corresponding to an one-way physical length fraction. seltVop is read/write available via seltTestInputEntry. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltInputImpedance0	1.3.6.1.4.1.193.72.300.20.1.4.1.51	OCTET STRING	read-only	Estimated input impedance of the line including far-end termination. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltInputImpedance1	1.3.6.1.4.1.193.72.300.20.1.4.1.52	OCTET STRING	read-only	Estimated input impedance of the line including far-end termination. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltInputImpedance2	1.3.6.1.4.1.193.72.300.20.1.4.1.53	OCTET STRING	read-only	Estimated input impedance of the line including far-end termination. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
OCT seltInputImpedance3	1.3.6.1.4.1.193.72.300.20.1.4.1.54	OCTET STRING	read-only	Estimated input impedance of the line including far-end termination. Part 0. Consecutive values are spaced 4.3125 kHz in frequency. If seltAdvOutputTableAct is deactivated the values should be ignored.
atmPvcTestInputTable	1.3.6.1.4.1.193.72.300.20.1.10		not-accessible	This table provides the input parameters for the ATM PVC test.
atmPvcTestInputEntry	1.3.6.1.4.1.193.72.300.20.1.10.1		not-accessible	An entry contains input parameters for the ATM PVC test for the subscriber line identified by lineIndex.
INT atmF5EndToEndLoopbackInterval	1.3.6.1.4.1.193.72.300.20.1.10.1.1	INTEGER	read-write	A number of 'ATM OAM F5 end-to-end loopback' cell(s) are sent with this interval on each PVC created for the subscriber line identified by lineIndex. The CPE must return a reply within atmF5EndToEndLoopbackTimeout seconds. The value zero indicates that this test is disabled. The first cell will be send when a non-zero value is written into this variable - or when the line is ready. If a resolution in msec is needed, use atmF5EndToEndLoopbackIntervalFine. Note: In order to restart a batch (if atmF5EndToEndBatchCount != 0) this parameter should be set to 0 and then set to the new (or possible) same interval.
INT atmF5EndToEndLoopbackTimeout	1.3.6.1.4.1.193.72.300.20.1.10.1.2	INTEGER	read-write	Specifies the the maximum amount of time to wait for F5 replies for a batch. (The batch size is set in atmF5EndToEndBatchSize)
INT atmF5EndToEndLoopbackIntervalFine	1.3.6.1.4.1.193.72.300.20.1.10.1.3	INTEGER	read-write	A number of 'ATM OAM F5 end-to-end loopback' cell(s) are sent with this interval on each PVC created for the subscriber line identified by lineIndex. The CPE must return a reply within atmF5EndToEndLoopbackTimeout seconds. The value zero indicates that this test is disabled. The first cell will be send when a non-zero value is written into this variable - or when the line is ready. This parameter follows atmF5EndToEndLoopbackInterval with a finer resolution. Note: In order to restart a batch (if atmF5EndToEndBatchCount != 0) this parameter should be set to 0 and then set to the new (or possible) same interval.
INT atmF5EndToEndBatchSize	1.3.6.1.4.1.193.72.300.20.1.10.1.5	INTEGER	read-write	Specifies how many F5 cells that is be sent in an interval given by atmF5EndToEndLoopbackIntervalFine and atmF5EndToEndLoopbackInterval.
INT atmF5EndToEndBatchCount	1.3.6.1.4.1.193.72.300.20.1.10.1.6	INTEGER	read-write	Specifies how many batches that should be run before automatically stopping the test. Eg. A BatchCount of 4 and an interval of 3 seconds would run for 12 seconds and send a total of 20 F5 cells if BatchSize equals 5. Note: A BatchCount of 0 indicates that the test should run until it is stopped by setting interval to 0.
atmPvcTestOutputTables	1.3.6.1.4.1.193.72.300.20.1.12
U32 atmPvcTestOutputTableVpiIndex	1.3.6.1.4.1.193.72.300.20.1.12.1	Unsigned32	not-accessible	The vpi index in atmPvcTestOutputTablePvc.
U32 atmPvcTestOutputTableVciIndex	1.3.6.1.4.1.193.72.300.20.1.12.2	Unsigned32	not-accessible	The vci index in atmPvcTestOutputTablePvc.
atmPvcTestOutputTableLine	1.3.6.1.4.1.193.72.300.20.1.12.4		not-accessible	This table provides the output parameters for the ATM PVC test (per line parameters).
atmPvcTestOutputEntryLine	1.3.6.1.4.1.193.72.300.20.1.12.4.1		not-accessible	An entry contains output parameters for the ATM PVC test for the subscriber line identified by lineIndex.
C32 atmF5EndToEndBatchesLeft	1.3.6.1.4.1.193.72.300.20.1.12.4.1.1	Counter32	read-only	If batches are used (defined with atmF5EndToEndBatchCount != 0) This counter states how many batches are left before all batches have been run.
atmPvcTestOutputTablePvc	1.3.6.1.4.1.193.72.300.20.1.12.6		not-accessible	This table provides the output parameters for the ATM PVC test (per pvc parameters).
atmPvcTestOutputEntryPvc	1.3.6.1.4.1.193.72.300.20.1.12.6.1		not-accessible	An entry contains output parameters for the ATM PVC test for the subscriber PVC identified by lineIndex, atmPvcTestOutputTableVpiIndex, and atmPvcTestOutputTableVciIndex.
C32 atmF5EndToEndTransmitted	1.3.6.1.4.1.193.72.300.20.1.12.6.1.1	Counter32	read-only	Number of F5 cells transmitted on the PVC since the test was started with atmF5EndToEndLoopbackIntervalFine or atmF5EndToEndLoopbackInterval.
C32 atmF5EndToEndReceived	1.3.6.1.4.1.193.72.300.20.1.12.6.1.2	Counter32	read-only	Number of F5 cells received on the PVC since the test was started with atmF5EndToEndLoopbackIntervalFine or atmF5EndToEndLoopbackInterval. Note: F5 cells from a previous batch that are received are droped and are not counted here. (ie. very late answers arriving later than atmF5EndToEndLoopbackInterval(Fine) or atmF5EndToEndLoopbackTimeout - whichever are smallest - after transmission of the requests)
pppoeTestInputTable	1.3.6.1.4.1.193.72.300.20.1.20		not-accessible	This table provides the input parameters for the 'PPP-over-Ethernet' test. Note: This OID has to be specified in 'adslIfTestType' in order to activate the test. The test is a PADI packet broadcasted on the Ethernet (through the Bridge/Filter for this line). The test succeds when at least one 'Access Concentrator' server replies with a PADO packet. See description of result in pppoeTestOutputTable. The returned AC-Name & Service-Names from each PADO packet will be stored in pppoeTestOutputTable. Abbreviations: - PADI: PPPoE Active Discovery Initiation - PADO: PPPoE Active Discovery Offer - AC-Name: Access Concentrator Name See also: 'peaIfIpDslam.adslIffObjects.adslIfTestTable.adslIfTestEntry.adslIfTestType'
pppoeTestInputEntry	1.3.6.1.4.1.193.72.300.20.1.20.1		not-accessible	An entry contains input parameters for the 'PPP-over-Ethernet' test for the subscriber line identified by lineIndex. See also summary in pppoeTestInputTable.
STR pppoeServiceRequested	1.3.6.1.4.1.193.72.300.20.1.20.1.1	DisplayString	read-write	The ServiceName used in the PADI packets (PPPoE Active Discovery Initiation) during PPPoE tests (default empty).
INT pppoeVlanId	1.3.6.1.4.1.193.72.300.20.1.20.1.2	INTEGER	read-write	This is the VLANID used for the pppoeTest (accordingly to 802.1Q). The VLANID must have been configured for this line in the pvcTable. See also 'peaBridgeIpDslam.pvcTable.pvcEntry.pvcStatus.vlanID'
INT pppoeTimeout	1.3.6.1.4.1.193.72.300.20.1.20.1.3	INTEGER	read-write	Specifies the the maximum amount of time to wait from the PADI packet is broadcasted until all replies (PADI packets) must have arrived.
INT pppoeInnerVlanId	1.3.6.1.4.1.193.72.300.20.1.20.1.4	INTEGER	read-write	This is the InnerVlanId used for the pppoeTest (accordingly to 802.1Q). This object is valid only if vlanTagType value is QinQ (Double Vlan). The innerVlanId must have been configured for this line in the pvcTable. See also 'peaBridgeIpDslam.pvcTable.pvcEntry.pvcStatus.innerVlanId'
pppoeTestOutputTable	1.3.6.1.4.1.193.72.300.20.1.21		not-accessible	This table provides the additional output parameters for the 'PPP-over-Ethernet' test. The test result can be read in the generic 'adslIfTestResult' variable, which can have the following values: - InProgress - UnableToRun, details in adslIfTestError: +- lanError: The specified VLAN-id is not used by any ATM PVCs that belongs to specified line (or line down). +- configurationOrCustomisationError: Bridge does now allow PPPoE frames for the PVC with specified VLAN-id. +- softwareError: Internal error. - TestFailed, details in adslIfTestError: +- timeoutExpired: No PADO reply received See also: 'peaIfIpDslam.adslIfObjects.adslIfTestTable'
pppoeTestOutputEntry	1.3.6.1.4.1.193.72.300.20.1.21.1		not-accessible	An entry contains additional output parameters for the 'PPP-over-Ethernet' test for the subscriber line identified by lineIndex. Zero or more entries may exists for each line.
STR pppoeAccessConcentrator	1.3.6.1.4.1.193.72.300.20.1.21.1.1	DisplayString	read-only	The name of the Access Concentrator reported in a PADO packet.
STR pppoeServiceOffered	1.3.6.1.4.1.193.72.300.20.1.21.1.2	DisplayString	read-only	The name of a Service reported in a PADO packet from the Access Concentrator.
U32 resultIndex	1.3.6.1.4.1.193.72.300.20.1.21.1.3	Unsigned32	not-accessible	Indicates the entry number for a line.
loopDiagResultTable	1.3.6.1.4.1.193.72.300.20.1.23		not-accessible	This table provides the per line results of the ADSL2 Loop Diagnostics.
loopDiagResultEntry	1.3.6.1.4.1.193.72.300.20.1.23.1		not-accessible	An entry contains the per line results of the ADSL2 Loop Diagnostics for the subscriber line identified by lineIndex.
INT loopDiagStatus	1.3.6.1.4.1.193.72.300.20.1.23.1.1	INTEGER	read-only	Status of current Loop Diagnostics. NOTE that Loop Diagnostics data are only valid in case of status LoopDiagSuccess.
U32 loopDiagAttainableBitRateNE	1.3.6.1.4.1.193.72.300.20.1.23.1.2	Unsigned32	read-only	Near-end attainable bit rate in bit per second (bps). Compliant to G.997.1: 7.5.1.13 (ATTNDRus).
U32 loopDiagLoopAttenuationNE	1.3.6.1.4.1.193.72.300.20.1.23.1.3	Unsigned32	read-only	Near-end loop attenuation. Range is [1023..0], unit is 0.1 dB. LoopAttenuation = 1023 is a special value indicating that the loop attenuation is outside the represented range. Compliant to G.997.1: 7.5.1.7 (LATNus).
U32 loopDiagSignalAttenuationNE	1.3.6.1.4.1.193.72.300.20.1.23.1.4	Unsigned32	read-only	Near-end signal attenuation. Range is [1023..0], unit is 0.1 dB. SignalAttenuation = 1023 is a special value indicating that the attenuation is outside the represented range. Compliant to G.997.1: 7.5.1.9 (SATNus).
I32 loopDiagSnrMarginNE	1.3.6.1.4.1.193.72.300.20.1.23.1.5	Integer32	read-only	Near-end signal-to-noise ratio margin. Range is [511..-512], unit is 0.1 dB. snrMargin = -512 is a special value indicating that the signal-to-noise ratio margin is outside the represented range. Compliant to G.997.1: 7.5.1.11 (SNRMus).
I32 loopDiagActualTxPowerFarEndNE	1.3.6.1.4.1.193.72.300.20.1.23.1.6	Integer32	read-only	The far-end actual aggregate transmit power as determined by the near-end receive PMD function. Range is [511..-512], unit is 0.1 dBm. actualTxPowerFE = -512 is a special value indicating that the actual aggregate transmit power is outside the represented range. Compliant to G.997.1: 7.5.1.17 (ACTATPus).
U32 loopDiagAttainableBitRateFE	1.3.6.1.4.1.193.72.300.20.1.23.1.7	Unsigned32	read-only	Far-end attainable bit rate in bit per second (bps). Compliant to G.997.1: 7.5.1.12 (ATTNDRds).
U32 loopDiagLoopAttenuationFE	1.3.6.1.4.1.193.72.300.20.1.23.1.8	Unsigned32	read-only	Far-end loop attenuation. Range is [1023..0], unit is 0.1 dB. LoopAttenuation = 1023 is a special value indicating that the attenuation is outside the represented range. Compliant to G.997.1: 7.5.1.6 (LATNds).
U32 loopDiagSignalAttenuationFE	1.3.6.1.4.1.193.72.300.20.1.23.1.9	Unsigned32	read-only	Far-end signal attenuation. Range is [1023..0], unit is 0.1 dB. SignalAttenuation = 1023 is a special value indicating that the attenuation is outside the represented range. Compliant to G.997.1: 7.5.1.8 (SATNds).
I32 loopDiagSnrMarginFE	1.3.6.1.4.1.193.72.300.20.1.23.1.10	Integer32	read-only	Far-end signal-to-noise ratio margin. Range is [511..-512], unit is 0.1 dB. SnrMargin = -512 is a special value indicating that the signal-to-noise ratio margin is outside the represented range. Compliant to G.997.1: 7.5.1.10 (SNRMds).
I32 loopDiagActualTxPowerFarEndFE	1.3.6.1.4.1.193.72.300.20.1.23.1.11	Integer32	read-only	The near-end actual aggregate transmit power as determined by the far-end receive PMD function. Range is [511..-512], unit is 0.1 dBm. ActualTxPowerFE = -512 is a special value indicating that the actual aggregate transmit power is outside the represented range. Compliant to G.997.1: 7.5.1.16 (ACTATPds).
loopDiagHlinNeTable	1.3.6.1.4.1.193.72.300.20.1.24		not-accessible	This table provides the per subcarrier Hlin results of the ADSL2 Loop Diagnostics. The linear complex channel transfer function values for the tone range specified by the partId. Hlin is calculated from the given values as follows: Hlin[i] = (HlinScale/215)(Hlin[i].real + jHlin[i].imag)/215) Compliant to G.997.1: 7.5.1.18.5 (HLINSCus) and 7.5.1.18.6 (HLINpsus).
loopDiagHlinNeEntry	1.3.6.1.4.1.193.72.300.20.1.24.1		not-accessible	An entry contains the per subcarrier Hlin results of the ADSL2 Loop Diagnostics for the subscriber line identified by lineIndex. NOTE Low designates the first 32 tones and High is the upper 32 tones for that particular partId.
U32 loopDiagHlinNeScale	1.3.6.1.4.1.193.72.300.20.1.24.1.1	Unsigned32	read-only	Scale factor for the normalized complex numbers Hlin.
OCT loopDiagHlinNeLow	1.3.6.1.4.1.193.72.300.20.1.24.1.2	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Bytes n4 + [0..1]: Real part (int16) Bytes n4 + [2..3]: Imaginary part (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinNeHigh	1.3.6.1.4.1.193.72.300.20.1.24.1.3	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Bytes n4 + [0..1]: Real part (int16) Bytes n4 + [2..3]: Imaginary part (int16) real[n] = imag[n] = -32768 indicates no measurement.
loopDiagHlinFeTable	1.3.6.1.4.1.193.72.300.20.1.25		not-accessible	This table provides the per subcarrier Hlin results of the ADSL2 Loop Diagnostics. The linear complex channel transfer function values for the tone range specified by the partId. Hlin is calculated from the given values as follows: Hlin[i] = (HlinScale/2^15)(Hlin[i].real + jHlin[i].imag)/2^15) Compliant to G.997.1: 7.5.1.18.1 (HLINSCds) and 7.5.1.18.2 (HLINpsds).
loopDiagHlinFeEntry	1.3.6.1.4.1.193.72.300.20.1.25.1		not-accessible	An entry contains the per subcarrier Hlin results of the ADSL2 Loop Diagnostics for the subscriber line identified by lineIndex. NOTE: The partId specifies the section of the Hlin table to return. The Hlin values returned correspond to tones: partId * 64 to (partId * 64 + 63). PartId range is [0..7]. Low designates the first 32 tones and High is the upper 32 tones for that particular partId.
U32 loopDiagHlinFeScalePart0	1.3.6.1.4.1.193.72.300.20.1.25.1.1	Unsigned32	read-only	Scale factor for the normalized complex numbers Hlin.
U32 loopDiagHlinFeScalePart1	1.3.6.1.4.1.193.72.300.20.1.25.1.2	Unsigned32	read-only	Scale factor for the normalized complex numbers Hlin.
U32 loopDiagHlinFeScalePart2	1.3.6.1.4.1.193.72.300.20.1.25.1.3	Unsigned32	read-only	Scale factor for the normalized complex numbers Hlin.
U32 loopDiagHlinFeScalePart3	1.3.6.1.4.1.193.72.300.20.1.25.1.4	Unsigned32	read-only	Scale factor for the normalized complex numbers Hlin.
U32 loopDiagHlinFeScalePart4	1.3.6.1.4.1.193.72.300.20.1.25.1.5	Unsigned32	read-only	Scale factor for the normalized complex numbers Hlin.
U32 loopDiagHlinFeScalePart5	1.3.6.1.4.1.193.72.300.20.1.25.1.6	Unsigned32	read-only	Scale factor for the normalized complex numbers Hlin.
U32 loopDiagHlinFeScalePart6	1.3.6.1.4.1.193.72.300.20.1.25.1.7	Unsigned32	read-only	Scale factor for the normalized complex numbers Hlin.
U32 loopDiagHlinFeScalePart7	1.3.6.1.4.1.193.72.300.20.1.25.1.8	Unsigned32	read-only	Scale factor for the normalized complex numbers Hlin.
OCT loopDiagHlinFePart0Low	1.3.6.1.4.1.193.72.300.20.1.25.1.9	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart0High	1.3.6.1.4.1.193.72.300.20.1.25.1.10	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart1Low	1.3.6.1.4.1.193.72.300.20.1.25.1.11	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart1High	1.3.6.1.4.1.193.72.300.20.1.25.1.12	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart2Low	1.3.6.1.4.1.193.72.300.20.1.25.1.13	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart2High	1.3.6.1.4.1.193.72.300.20.1.25.1.14	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart3Low	1.3.6.1.4.1.193.72.300.20.1.25.1.15	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart3High	1.3.6.1.4.1.193.72.300.20.1.25.1.16	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart4Low	1.3.6.1.4.1.193.72.300.20.1.25.1.17	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart4High	1.3.6.1.4.1.193.72.300.20.1.25.1.18	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart5Low	1.3.6.1.4.1.193.72.300.20.1.25.1.19	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart5High	1.3.6.1.4.1.193.72.300.20.1.25.1.20	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart6Low	1.3.6.1.4.1.193.72.300.20.1.25.1.21	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart6High	1.3.6.1.4.1.193.72.300.20.1.25.1.22	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart7Low	1.3.6.1.4.1.193.72.300.20.1.25.1.23	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
OCT loopDiagHlinFePart7High	1.3.6.1.4.1.193.72.300.20.1.25.1.24	OCTET STRING	read-only	The linear complex channel transfer function values for the tone range specified by the partId. Range is [32767..-32768]. Bytes n4 + [0..1]: Real part(n) (int16) Bytes n4 + [2..3]: Imaginary part(n) (int16) real[n] = imag[n] = -32768 indicates no measurement.
loopDiagHlogTable	1.3.6.1.4.1.193.72.300.20.1.26		not-accessible	This table provides the per subcarrier Hlog results of the ADSL2 Loop Diagnostics. Hlog is calculated from the given values, as follows: Hlog[i] = 6 - hlogNE(i)/10(dB) and Hlog[i] = 6 - hlogFE(i)/10(dB) Compliant to G.997.1: 7.5.1.18.4 (HLOGpsds) and 7.5.1.18.8 (HLOGpsus)
loopDiagHlogEntry	1.3.6.1.4.1.193.72.300.20.1.26.1		not-accessible	An entry contains the per subcarrier Hlog results of the ADSL2 Loop Diagnostics for the subscriber line identified by lineIndex. NOTE: The partId specifies the section of the far-end (US) Hlog table to return. The hlog values returned correspond to tones partId * 128 to (partId * 128 + 127). PartId range is [3..0]. Low designates the first 64 tones and High is the upper 64 tones for that particular partId.
OCT loopDiagHlogNE	1.3.6.1.4.1.193.72.300.20.1.26.1.1	OCTET STRING	read-only	The near-end logarithmic scale channel transfer function magnitudes. Range is [1023..0]. The value 1023 indicates no measurement available. Bytes n*2 + [0..1]: Hlog(n) (uint16)
OCT loopDiagHlogFEPart0Low	1.3.6.1.4.1.193.72.300.20.1.26.1.2	OCTET STRING	read-only	The far-end logarithmic scale channel transfer function magnitudes. Range is [1023..0]. The value 1023 indicates no measurement available. Bytes n*2 + [0..1]: Hlog(n) (uint16)
OCT loopDiagHlogFEPart0High	1.3.6.1.4.1.193.72.300.20.1.26.1.3	OCTET STRING	read-only	The far-end logarithmic scale channel transfer function magnitudes. Range is [1023..0]. The value 1023 indicates no measurement available. Bytes n*2 + [0..1]: Hlog(n) (uint16)
OCT loopDiagHlogFEPart1Low	1.3.6.1.4.1.193.72.300.20.1.26.1.4	OCTET STRING	read-only	The far-end logarithmic scale channel transfer function magnitudes. Range is [1023..0]. The value 1023 indicates no measurement available. Bytes n*2 + [0..1]: Hlog(n) (uint16)
OCT loopDiagHlogFEPart1High	1.3.6.1.4.1.193.72.300.20.1.26.1.5	OCTET STRING	read-only	The far-end logarithmic scale channel transfer function magnitudes. Range is [1023..0]. The value 1023 indicates no measurement available. Bytes n*2 + [0..1]: Hlog(n) (uint16)
OCT loopDiagHlogFEPart2Low	1.3.6.1.4.1.193.72.300.20.1.26.1.6	OCTET STRING	read-only	The far-end logarithmic scale channel transfer function magnitudes. Range is [1023..0]. The value 1023 indicates no measurement available. Bytes n*2 + [0..1]: Hlog(n) (uint16)
OCT loopDiagHlogFEPart2High	1.3.6.1.4.1.193.72.300.20.1.26.1.7	OCTET STRING	read-only	The far-end logarithmic scale channel transfer function magnitudes. Range is [1023..0]. The value 1023 indicates no measurement available. Bytes n*2 + [0..1]: Hlog(n) (uint16)
OCT loopDiagHlogFEPart3Low	1.3.6.1.4.1.193.72.300.20.1.26.1.8	OCTET STRING	read-only	The far-end logarithmic scale channel transfer function magnitudes. Range is [1023..0]. The value 1023 indicates no measurement available. Bytes n*2 + [0..1]: Hlog(n) (uint16)
OCT loopDiagHlogFEPart3High	1.3.6.1.4.1.193.72.300.20.1.26.1.9	OCTET STRING	read-only	The far-end logarithmic scale channel transfer function magnitudes. Range is [1023..0]. The value 1023 indicates no measurement available. Bytes n*2 + [0..1]: Hlog(n) (uint16)
loopDiagQlnTable	1.3.6.1.4.1.193.72.300.20.1.27		not-accessible	This table provides the per subcarrier Qln results of the ADSL2 Loop Diagnostics. QLN is calculated from the given values as follows: QLN[i] = -23 - (n[i]/2)(dBm/Hz), where n designates the QlnNE and QlnFE respectively. Compliant to G.997.1: 7.5.1.19.2 (QLNpsds) and 7.5.1.19.4 (QLNpsus)
loopDiagQlnEntry	1.3.6.1.4.1.193.72.300.20.1.27.1		not-accessible	An entry contains the per subcarrier Qln results of the ADSL2 Loop Diagnostics for the subscriber line identified by lineIndex. NOTE: The partId specifies the section of the far-end (US) QLN table to return. The QLN values returned correspond to tones partId * 256 to (partId * 256 + 255). PartId range is [1..0]. Low designates the first 128 tones and High is the upper 128 tones for that particular partId.
OCT loopDiagQlnNE	1.3.6.1.4.1.193.72.300.20.1.27.1.1	OCTET STRING	read-only	The near-end quiet line noise PSD. Range is [255..0]. The value 255 indicates no measurement available.
OCT loopDiagQlnFEPart0Low	1.3.6.1.4.1.193.72.300.20.1.27.1.2	OCTET STRING	read-only	The far-end quiet line noise PSD. Range is [255..0]. The value 255 indicates no measurement available.
OCT loopDiagQlnFEPart0High	1.3.6.1.4.1.193.72.300.20.1.27.1.3	OCTET STRING	read-only	The far-end quiet line noise PSD. Range is [255..0]. The value 255 indicates no measurement available.
OCT loopDiagQlnFEPart1Low	1.3.6.1.4.1.193.72.300.20.1.27.1.4	OCTET STRING	read-only	The far-end quiet line noise PSD. Range is [255..0]. The value 255 indicates no measurement available.
OCT loopDiagQlnFEPart1High	1.3.6.1.4.1.193.72.300.20.1.27.1.5	OCTET STRING	read-only	The far-end quiet line noise PSD. Range is [255..0]. The value 255 indicates no measurement available.
loopDiagSnrTable	1.3.6.1.4.1.193.72.300.20.1.28		not-accessible	This table provides the per subcarrier Snr results of the ADSL2 Loop Diagnostics. SNR is calculated from the given values as follows: SNR[i] = -32 + (n[i]/2)(dB) where n designates the SnrNE and SnrFE respectively. Compliant to G.997.1: 7.5.1.20.2 (SNRpsds) and 7.5.1.20.4 (SNRpsus)
loopDiagSnrEntry	1.3.6.1.4.1.193.72.300.20.1.28.1		not-accessible	An entry contains the per subcarrier Snr results of the ADSL2 Loop Diagnostics for the subscriber line identified by lineIndex. NOTE: The partId specifies the section of the far-end (US) SNR table to return. The SNR values returned correspond to tones partId * 256 to (partId * 256 + 255). PartId range is [0..1]. Low designates the first 128 tones and High is the upper 128 tones for that particular partId.
OCT loopDiagSnrNE	1.3.6.1.4.1.193.72.300.20.1.28.1.1	OCTET STRING	read-only	The near-end signal-to-noise ratio. Range is [255..0]. The value 255 indicates no measurement available.
OCT loopDiagSnrFEPart0Low	1.3.6.1.4.1.193.72.300.20.1.28.1.2	OCTET STRING	read-only	The far-end signal-to-noise ratio. Range is [255..0]. The value 255 indicates no measurement available.
OCT loopDiagSnrFEPart0High	1.3.6.1.4.1.193.72.300.20.1.28.1.3	OCTET STRING	read-only	The far-end signal-to-noise ratio. Range is [255..0]. The value 255 indicates no measurement available.
OCT loopDiagSnrFEPart1Low	1.3.6.1.4.1.193.72.300.20.1.28.1.4	OCTET STRING	read-only	The far-end signal-to-noise ratio. Range is [255..0]. The value 255 indicates no measurement available.
OCT loopDiagSnrFEPart1High	1.3.6.1.4.1.193.72.300.20.1.28.1.5	OCTET STRING	read-only	The far-end signal-to-noise ratio. Range is [255..0]. The value 255 indicates no measurement available.
peaTestIpDslamTraps	1.3.6.1.4.1.193.72.300.20.2
peaTestIpDslamTrapsEntry	1.3.6.1.4.1.193.72.300.20.2.0
NTF ifTestCompletion	1.3.6.1.4.1.193.72.300.20.2.0.1			Indicates that the test is ready. Valid from: EDA 1.1R2A Parameters 1: Managed object class IP DSLAM Port 2: Managed object ID (MAC + PortNo) 3: Sequence number (Alarm sequence number) 4: Perceived severity Warning 5: Event time (Timestamp is retrieved from a SNTP server) 6: Event type Equipment 7: Probable cause Other 8: Test Result (Success, NotSupported, UnableToRun, Aborted or Failed) 9: Test Type (Type of the test performed) 10: Test Error (Probable cause value)
peaTestIpDslamObjectsGroups	1.3.6.1.4.1.193.72.300.20.3
peaTestIpDslamObjectsGroup	1.3.6.1.4.1.193.72.300.20.3.1			Objects for the fssServiceLine Group
peaTestIpDslamTrapsGroups	1.3.6.1.4.1.193.72.300.20.4
peaTestIpDslamTrapsGroup	1.3.6.1.4.1.193.72.300.20.4.2			Deprecated Notifications Group

RFC description

Controls SELT loop qualification and noise testing on Ericsson IP DSLAM access equipment.

Start monitoring Ericsson (Diax) IP-DSLAM broadband access equipment (SELT/noise test control) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download PEA-TEST-IPDSLAM

What Is PEA-TEST-IPDSLAM?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description