All MIBs › PEA-TEST-IPDSLAM › atmF5EndToEndLoopbackInterval
atmF5EndToEndLoopbackInterval
Module: PEA-TEST-IPDSLAM
OID (symbolic): PEA-TEST-IPDSLAM::atmF5EndToEndLoopbackInterval
OID (numeric): 1.3.6.1.4.1.193.72.300.20.1.10.1.1
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: A number of 'ATM OAM F5 end-to-end loopback' cell(s) are sent with this interval on each PVC created for the subscriber line identified by lineIndex. The CPE must return a reply within atmF5EndToEndLoopbackTimeout seconds. The value zero indicates that this test is disabled. The first cell will be send when a non-zero value is written into this variable - or when the line is ready.
If a resolution in msec is needed, use atmF5EndToEndLoopbackIntervalFine.
Note: In order to restart a batch (if atmF5EndToEndBatchCount != 0) this parameter should be set to 0 and then set to the new (or possible) same interval.
What is atmF5EndToEndLoopbackInterval?
How often, in whole seconds (0-3600), the device sends an ATM OAM F5 end-to-end loopback cell on each PVC for this line, expecting the CPE to echo it back within atmF5EndToEndLoopbackTimeout seconds; set to 0 to stop the test, and restart a running batch by setting this to 0 then back to the desired interval. Use atmF5EndToEndLoopbackIntervalFine instead if you need sub-second timing.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.193.72.300.20.1.10.1.1 snmpwalk -v2c -c public <target> PEA-TEST-IPDSLAM::atmF5EndToEndLoopbackInterval
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.193.72.300.20.1.10.1.1.1 snmpget -v2c -c public <target> PEA-TEST-IPDSLAM::atmF5EndToEndLoopbackInterval.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.193.72.300.20.1.10.1.1.1 i <value>
Start monitoring Ericsson (Diax) IP-DSLAM broadband access equipment (SELT/noise test control) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the PEA-TEST-IPDSLAM::atmF5EndToEndLoopbackInterval OID value, configure state conditions and alerts, and monitor any Ericsson (Diax) IP-DSLAM broadband access equipment (SELT/noise test control) from a single console.
OID Breakdown
Upper-level ancestors (9 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.193 | ericsson | ANS-COMMON-MIB |
| 1.3.6.1.4.1.193.72 | diaxMIB | DXD-SMI |
| 1.3.6.1.4.1.193.72.300 | peaIpDslam | DIESEL-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.193.72.300.20 | peaTestIpDslam | PEA-TEST-IPDSLAM |
| 1.3.6.1.4.1.193.72.300.20.1 | peaTestIpDslamObjects | PEA-TEST-IPDSLAM |
| 1.3.6.1.4.1.193.72.300.20.1.10 | atmPvcTestInputTable | PEA-TEST-IPDSLAM |
| 1.3.6.1.4.1.193.72.300.20.1.10.1 | atmPvcTestInputEntry | PEA-TEST-IPDSLAM |
| 1.3.6.1.4.1.193.72.300.20.1.10.1.1 | atmF5EndToEndLoopbackInterval | PEA-TEST-IPDSLAM |