E7-Calix-MIB

All MIBs › E7-Calix-MIB

Organization: Calix Network, Inc.

Last Updated: 2013-04-03

Category: DSL and Broadband, Domain: DSL/xPON, Vendor: Calix

Description: Core management MIB for the Calix E7 multi-service access platform defining system configuration, service, and interface objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is E7-Calix-MIB?

E7-Calix-MIB is the top-level infrastructure MIB for Calix's E7 multi-service access platform family, also covering the related E5-400 and E5-312 products, defining core system, chassis, and card management objects (fault management is handled separately). It exposes hardware inventory and configuration data through structures like e7CardTable, describing each card slot's bank, index, provisioned and actual card type, and administrative status, alongside interface groupings such as e7VdslPortGroup for VDSL line cards. It is heavily oriented toward monitoring hardware status: e7CardCurrentPowerLevel tracks power draw per card, e7CardSoftwareVersion and e7CardSerialNumber track firmware/version and asset identity, and e7CardAdminStatus/e7CardRowStatus reveal whether a card slot is administratively enabled or has been pulled/inserted. Because fault management is explicitly excluded from this module, it likely depends on a companion Calix E7 fault/alarm MIB (and standard MIBs like ENTITY-MIB/IF-MIB) for trap-based alerting and interface counters. It is deployed by broadband service providers managing Calix E7 chassis-based multi-service access platforms at central offices or remote terminals. Engineers can download the E7-Calix-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in E7-Calix-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Calix E7 multi-service access platform
Calix E5-400 access platform
Calix E5-312 access platform

Monitoring Examples

An administrator polls e7CardTable/e7CardEntry across e7CardBank and e7CardIndex to inventory installed cards, comparing e7CardProvType against e7CardActualType to catch a mismatch where a different card model was physically inserted than what was provisioned. Checking e7CardSoftwareVersion across cards identifies units running outdated firmware, while e7CardCurrentPowerLevel trending upward can flag a failing power supply on that card. e7CardAdminStatus combined with e7CardRowStatus shows whether a slot is enabled and its row lifecycle state, useful for detecting a removed or pending-activation card, and e7CardCleiCode confirms the exact hardware variant for asset tracking.

What Can Be Monitored

installed card inventory
provisioned vs actual card type
card admin status
card software/firmware version
card serial number
per-card power level
VDSL port group configuration

Imported Objects

From CALIX-PRODUCT-MIB

e7	OBJECT-IDENTITY
e7Modules	OBJECT-IDENTITY

From E7-TC

E7AdminStatus
E7CardType
E7PowerLevel
E7SnmpVers

From IF-MIB

ifIndex

OBJECT-TYPE

From SNMPv2-SMI

Counter64
Integer32
IpAddress
mib-2

From SNMPv2-TC

DisplayString
MacAddress
RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
e7ResourceModule	1.3.6.1.4.1.6321.1.2.2.1.1			Top-level infrastructure for the Calix E7, E5-400, and E5-312 products, except for Fault Management.
e7Resource	1.3.6.1.4.1.6321.1.2.2.2
e7NodeResource	1.3.6.1.4.1.6321.1.2.2.2.1
e7CardGroup	1.3.6.1.4.1.6321.1.2.2.2.1.6
e7CardTable	1.3.6.1.4.1.6321.1.2.2.2.1.6.1		not-accessible	Contains Card entries
e7CardEntry	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1		not-accessible	List of attributes related to Card
I32 e7CardBank	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1.1	Integer32	not-accessible	Bank number
I32 e7CardIndex	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1.2	Integer32	not-accessible	Slot number
ROW e7CardRowStatus	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1.3	RowStatus	read-create	Controls creation & deletion of table entries. Only active(get), createAndGo(set), and destroy(set) are supported.
E7A e7CardAdminStatus	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1.4	E7AdminStatus	read-create	Administrative status
E7C e7CardProvType	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1.5	E7CardType	read-create	Provisioned card type
E7C e7CardActualType	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1.6	E7CardType	read-only	Actual card type
OCT e7CardSoftwareVersion	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1.7	OCTET STRING	read-only	Running software version, dotted string notation
STR e7CardSerialNumber	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1.8	DisplayString	read-only	Ascii Serial number for card
E7P e7CardCurrentPowerLevel	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1.9	E7PowerLevel	read-only	Current power level for card
OCT e7CardCleiCode	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1.10	OCTET STRING	read-only	Ascii CLEI code for card
OCT e7CardPartNumber	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1.11	OCTET STRING	read-only	Ascii part number
OCT e7CardStartMacRange	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1.12	OCTET STRING	read-only	Start of MAC range (ascii)
OCT e7CardEndMacRange	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1.13	OCTET STRING	read-only	End of MAC range (ascii)
OCT e7CardHardwareRevision	1.3.6.1.4.1.6321.1.2.2.2.1.6.1.1.14	OCTET STRING	read-only	Hardware revision, dotted string notation
I32 e7CardTableEnd	1.3.6.1.4.1.6321.1.2.2.2.1.6.2	Integer32	read-only	denotes the end of the e7CardTable (for getnext)
e7SystemGroup	1.3.6.1.4.1.6321.1.2.2.2.1.7
OCT e7SystemId	1.3.6.1.4.1.6321.1.2.2.2.1.7.1	OCTET STRING	read-create	Unique name of the system
OCT e7SystemLocation	1.3.6.1.4.1.6321.1.2.2.2.1.7.2	OCTET STRING	read-create	Location of the system
INT e7SystemAutoUpgrade	1.3.6.1.4.1.6321.1.2.2.2.1.7.3	INTEGER	read-create	Auto upgrade out-of-rev cards on arrival
INT e7SystemTelnetServer	1.3.6.1.4.1.6321.1.2.2.2.1.7.4	INTEGER	read-create	Enable CLI access via telnet (in addition to ssh)
INT e7SystemUnsecuredWeb	1.3.6.1.4.1.6321.1.2.2.2.1.7.5	INTEGER	read-create	Enable unsecured web-access (non-ssh)
I32 e7SystemPasswordExpiry	1.3.6.1.4.1.6321.1.2.2.2.1.7.6	Integer32	read-create	Craft user password expiry, in days
IP e7SystemDnsPrimary	1.3.6.1.4.1.6321.1.2.2.2.1.7.7	IpAddress	read-create	IP address of primary DNS server
IP e7SystemDnsSecondary	1.3.6.1.4.1.6321.1.2.2.2.1.7.8	IpAddress	read-create	IP address of secondary DNS server
OCT e7SystemTimezone	1.3.6.1.4.1.6321.1.2.2.2.1.7.9	OCTET STRING	read-create	Timezone for system
STR e7SystemChassisSerialNumber	1.3.6.1.4.1.6321.1.2.2.2.1.7.10	DisplayString	read-create	Chassis serial number
MAC e7SystemChassisMacAddress	1.3.6.1.4.1.6321.1.2.2.2.1.7.11	MacAddress	read-create	Chassis MAC address
STR e7SystemTime	1.3.6.1.4.1.6321.1.2.2.2.1.7.12	DisplayString	read-create	system time
STR e7SystemDate	1.3.6.1.4.1.6321.1.2.2.2.1.7.13	DisplayString	read-create	system date
e7TrapDestGroup	1.3.6.1.4.1.6321.1.2.2.2.1.8
e7TrapDestTable	1.3.6.1.4.1.6321.1.2.2.2.1.8.1		not-accessible	Contains SNMP Trap Dest entries
e7TrapDestEntry	1.3.6.1.4.1.6321.1.2.2.2.1.8.1.1		not-accessible	List of attributes related to SNMP Trap Dest
I32 e7TrapDestIndex	1.3.6.1.4.1.6321.1.2.2.2.1.8.1.1.1	Integer32	not-accessible	trap index
ROW e7TrapDestRowStatus	1.3.6.1.4.1.6321.1.2.2.2.1.8.1.1.2	RowStatus	read-create	Controls creation & deletion of table entries. Only active(get), createAndGo(set), and destroy(set) are supported.
E7A e7TrapDestAdminStatus	1.3.6.1.4.1.6321.1.2.2.2.1.8.1.1.3	E7AdminStatus	read-create	Administrative status
IP e7TrapDestIpAddress	1.3.6.1.4.1.6321.1.2.2.2.1.8.1.1.4	IpAddress	read-create	destination IP address
I32 e7TrapDestPortNumber	1.3.6.1.4.1.6321.1.2.2.2.1.8.1.1.5	Integer32	read-create	destination UDP port number
E7S e7TrapDestSnmpVers	1.3.6.1.4.1.6321.1.2.2.2.1.8.1.1.6	E7SnmpVers	read-create	v2c or v3 trap type
OCT e7TrapDestV3User	1.3.6.1.4.1.6321.1.2.2.2.1.8.1.1.7	OCTET STRING	read-create	user used in v3 traps
OCT e7TrapDestCommunity	1.3.6.1.4.1.6321.1.2.2.2.1.8.1.1.8	OCTET STRING	read-create	community string used in v2c traps
e7PortGroup	1.3.6.1.4.1.6321.1.2.2.2.1.9
e7VdslPortGroup	1.3.6.1.4.1.6321.1.2.2.2.1.9.1
e7VdslPortTable	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.1		not-accessible	Contains Vdsl port entries
e7VdslPortEntry	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.1.1		not-accessible	List of attributes related to Vdsl Port entries
ROW e7VdslPortRowStatus	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.1.1.1	RowStatus	read-create	Controls creation & deletion of table entries. Only active(get), createAndGo(set), and destroy(set) are supported.
E7A e7VdslPortAdminStatus	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.1.1.2	E7AdminStatus	read-create	Administrative status
I32 e7VdslPortCurrTxRate	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.1.1.3	Integer32	read-only	Actual transmit data rate this port
I32 e7VdslPortCurrRxRate	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.1.1.4	Integer32	read-only	Actual receive data rate this port
INT e7VdslPortStatsProtocol	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.1.1.5	INTEGER	read-create	Administrative status
INT e7VdslPortLineState	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.1.1.6	INTEGER	read-create	Line operational status
e7VdslRateTable	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.2		not-accessible	Contains Vdsl data rate entries
e7VdslRateEntry	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.2.1		not-accessible	List of attributes related to Vdsl Rate entries
ROW e7VdslRateRowStatus	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.2.1.1	RowStatus	read-create	Controls creation & deletion of table entries. Only active(get), createAndGo(set), and destroy(set) are supported.
E7A e7VdslRateAdminStatus	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.2.1.2	E7AdminStatus	read-create	Administrative status
I32 e7VdslRateProvDataRateUs	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.2.1.3	Integer32	read-only	Provisioned data rate upstream
I32 e7VdslRateProvDataRateDs	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.2.1.4	Integer32	read-only	Provisioned data rate downstream
e7VdslPhysTable	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.3		not-accessible	Contains Vdsl physical entries
e7VdslPhysEntry	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.3.1		not-accessible	List of attributes related to Vdsl physical entries
INT e7VdslPhysSide	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.3.1.1	INTEGER	not-accessible	Identifies whether the transceiver is downstream or upstream.
I32 e7VdslPhysCurrSnrMargin	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.3.1.2	Integer32	read-only	Noise Margin as seen by this Vtu with respect to its received signal.
I32 e7VdslPhysCurrAtn	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.3.1.3	Integer32	read-only	Measured difference in the total power transmitted by the peer Vtu and the total power received by this Vtu.
I32 e7VdslPhysCurrOutputPwr	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.3.1.4	Integer32	read-only	Measured total output power transmitted by this VTU. This is the measurement that was reported during the last activation sequence.
I32 e7VdslPhysInterleaveDelay	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.3.1.5	Integer32	read-only	Actual interleaving delay (in milliseconds).
I32 e7VdslPhysImpulseNoiseProtection	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.3.1.6	Integer32	read-only	Actual impulse noise protection.
INT e7VdslPhysTransmissionMode	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.3.1.7	INTEGER	read-only	Actual transmission mode.
e7VdslPortCfgTable	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4		not-accessible	Contains Vdsl port configuration entries
e7VdslPortCfgEntry	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1		not-accessible	List of attributes related to Vdsl Port configuration entries
INT e7VdslPortCfgServiceType	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.1	INTEGER	read-write	VDSL port configured service type.
INT e7VdslPortCfgPathLatency	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.2	INTEGER	read-write	VDSL port configured latency.
INT e7VdslPortCfgVdslProfile	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.3	INTEGER	read-write	VDSL port configured profile.
I32 e7VdslPortCfgDsMinRate	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.4	Integer32	read-write	VDSL port configured downstream minimum rate.
I32 e7VdslPortCfgDsMaxRate	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.5	Integer32	read-write	VDSL port configured downstream maximum rate.
I32 e7VdslPortCfgUsMinRate	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.6	Integer32	read-write	VDSL port configured upstream minimum rate.
I32 e7VdslPortCfgUsMaxRate	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.7	Integer32	read-write	VDSL port configured upstream maximum rate.
INT e7VdslPortCfgDsMinInp	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.8	INTEGER	read-write	VDSL port configured downstream minimum impulse noise protection.
INT e7VdslPortCfgUsMinInp	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.9	INTEGER	read-write	VDSL port configured upstream minimum impulse noise protection.
I32 e7VdslPortCfgDsInterleaveMaxLatency	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.10	Integer32	read-write	VDSL port configured downstream interleave maximum latency. A value of 0x7FFFFFFF (2147483647) indicates the setting equal to 'auto'.
I32 e7VdslPortCfgUsInterleaveMaxLatency	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.11	Integer32	read-write	VDSL port configured upstream interleave maximum latency.
I32 e7VdslPortCfgDsMinSnr	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.12	Integer32	read-write	VDSL port configured downstream minimum SNR.
I32 e7VdslPortCfgDsMaxSnr	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.13	Integer32	read-write	VDSL port configured downstream maximum SNR.
I32 e7VdslPortCfgDsTargetSnr	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.14	Integer32	read-write	VDSL port configured downstream target SNR.
I32 e7VdslPortCfgUsMinSnr	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.15	Integer32	read-write	VDSL port configured upstream minimum SNR.
I32 e7VdslPortCfgUsMaxSnr	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.16	Integer32	read-write	VDSL port configured upstream maximum SNR.
I32 e7VdslPortCfgUsTargetSnr	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.17	Integer32	read-write	VDSL port configured upstream target SNR.
INT e7VdslPortCfgPsdMask	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.18	INTEGER	read-write	VDSL port configured PSD mask.
STR e7VdslPortCfgLastTemplate	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.4.1.19	DisplayString	read-create	VDSL port configured last template name.
e7VdslPortCfgTemplateTable	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5		not-accessible	Contains Vdsl port configuration template entries
e7VdslPortCfgTemplateEntry	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1		not-accessible	List of attributes related to Vdsl Port configuration template entries
I32 e7VdslPortCfgTemplateIndex	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.1	Integer32	read-write	VDSL port configured template index.
STR e7VdslPortCfgTemplateName	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.2	DisplayString	read-create	VDSL port configured template name.
INT e7VdslPortCfgTemplateServiceType	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.3	INTEGER	read-write	VDSL port configured service type. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
INT e7VdslPortCfgTemplatePathLatency	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.4	INTEGER	read-write	VDSL port configured latency. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
INT e7VdslPortCfgTemplateVdslProfile	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.5	INTEGER	read-write	VDSL port configured profile. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
I32 e7VdslPortCfgTemplateDsMinRate	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.6	Integer32	read-write	VDSL port configured downstream minimum rate. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
I32 e7VdslPortCfgTemplateDsMaxRate	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.7	Integer32	read-write	VDSL port configured downstream maximum rate. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
I32 e7VdslPortCfgTemplateUsMinRate	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.8	Integer32	read-write	VDSL port configured upstream minimum rate. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
I32 e7VdslPortCfgTemplateUsMaxRate	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.9	Integer32	read-write	VDSL port configured upstream maximum rate. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
INT e7VdslPortCfgTemplateDsMinInp	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.10	INTEGER	read-write	VDSL port configured downstream minimum impulse noise protection. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
INT e7VdslPortCfgTemplateUsMinInp	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.11	INTEGER	read-write	VDSL port configured upstream minimum impulse noise protection. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
I32 e7VdslPortCfgTemplateDsInterleaveMaxLatency	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.12	Integer32	read-write	VDSL port configured downstream interleave maximum latency. A value of 0x7FFFFFFF (2147483647) indicates the setting equal to 'auto'.
I32 e7VdslPortCfgTemplateUsInterleaveMaxLatency	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.13	Integer32	read-write	VDSL port configured upstream interleave maximum latency. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
I32 e7VdslPortCfgTemplateDsMinSnr	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.14	Integer32	read-write	VDSL port configured downstream minimum SNR. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
I32 e7VdslPortCfgTemplateDsMaxSnr	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.15	Integer32	read-write	VDSL port configured downstream maximum SNR. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
I32 e7VdslPortCfgTemplateDsTargetSnr	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.16	Integer32	read-write	VDSL port configured downstream target SNR. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
I32 e7VdslPortCfgTemplateUsMinSnr	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.17	Integer32	read-write	VDSL port configured upstream minimum SNR. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
I32 e7VdslPortCfgTemplateUsMaxSnr	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.18	Integer32	read-write	VDSL port configured upstream maximum SNR. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
I32 e7VdslPortCfgTemplateUsTargetSnr	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.19	Integer32	read-write	VDSL port configured upstream target SNR. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
INT e7VdslPortCfgTemplatePsdMask	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.5.1.20	INTEGER	read-write	VDSL port configured PSD mask. If template attribute is not set, value reported will be 0x7FFFFFFF (2147483647).
e7VdslPortPerfIntervalTable	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.6		not-accessible	Contains Vdsl port performance monitoring entries
e7VdslPortPerfIntervalEntry	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.6.1		not-accessible	List of attributes related to Vdsl Port performance monitoring entries
I32 e7VdslPortPerfIntervalPhysSide	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.6.1.1	Integer32	not-accessible	VDSL port performance interval phyical side.
I32 e7VdslPortPerfIntervalNumber	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.6.1.2	Integer32	not-accessible	VDSL port performance interval number.
I32 e7VdslPortPerfIntervalUAS	1.3.6.1.4.1.6321.1.2.2.2.1.9.1.6.1.3	Integer32	read-only	VDSL port performance interval unavailable seconds.

RFC description

System resource infrastructure for Calix E7 optical access platforms.

Start monitoring Calix access platforms with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download E7-Calix-MIB

What Is E7-Calix-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description