All MIBs › PCUBE-SE-MIB
Organization: Cisco Systems, Inc.
Last Updated: 2006-11-07
Category: DPI/Subscriber Management, Security
Description: Monitors Cisco P-Cube SCE subscriber management, providing per-subscriber traffic quota, policy enforcement, and DPI classification counters.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is PCUBE-SE-MIB?
PCUBE-SE-MIB is the main Cisco Systems SNMP MIB for the SCE (Service Control Engine) product family (SCE2000, SE100), providing chassis, control-module, and line-module configuration and runtime status. Its objects cover system operational status, failure-recovery mode, software version, chassis type/slot config/PSU type, power-supply/fan/temperature/voltage/line-feed alarm flags, slot count, and a module table (index, type, traffic-processor count, slot number, hardware version, port/link counts, connection mode, serial number, upstream attack-filtering time/last-filtering-time). As a hardware-status MIB it lets an administrator confirm chassis alarm state and which modules are actively filtering upstream attack traffic. It is deployed on Cisco SCE2000/SE100 Service Control Engine platforms. Engineers can download the PCUBE-SE-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in PCUBE-SE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco SCE2000/SE100 Service Control Engine platforms
Monitoring Examples
An administrator checks pchassisTempAlarm and pmoduleUpStreamAttackFilteringTime to confirm chassis health and active attack mitigation on a Cisco SCE2000 Service Control Engine.
What Can Be Monitored
- chassis alarms and module attack-filtering status
This MIB depends on
Related MIBs
Imported Objects
From PCUBE-SMI
| pcubeModules | OBJECT-IDENTITY |
| pcubeWorkgroup | OBJECT-IDENTITY |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter64 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION |
How to Use in IPNetwork Monitor
Example using txQueuesDroppedBytes OID:
Select a Cisco SCE2000/SE100 Service Control Engine platform as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type txQueuesDroppedBytes into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the amount of dropped L3 bytes. This is valid only if the system is configured to count dropped bytes per TX queue. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| pcubeSeMIB | 1.3.6.1.4.1.5655.2.3 | Main SNMP MIB for Cisco's SCE OS products such as SCE2000 and SE100. This MIB provides configuration and runtime status for chassis, control modules, and line modules on the SCOS systems. | ||
| pcubeSeConformance | 1.3.6.1.4.1.5655.2.3.1 | |||
| pcubeSeGroups | 1.3.6.1.4.1.5655.2.3.1.1 | |||
| pcubeSystemGroup | 1.3.6.1.4.1.5655.2.3.1.1.1 | System related inforamation. | ||
| pcubeChassisGroup | 1.3.6.1.4.1.5655.2.3.1.1.2 | Chassis related information. | ||
| pcuebModuleGroup | 1.3.6.1.4.1.5655.2.3.1.1.3 | Module related information. | ||
| pcubeLinkGroup | 1.3.6.1.4.1.5655.2.3.1.1.4 | Link related information. | ||
| pcubeDiskGroup | 1.3.6.1.4.1.5655.2.3.1.1.5 | Disk related information. | ||
| pcubeRdrFormatterGroup | 1.3.6.1.4.1.5655.2.3.1.1.6 | RDR-Formatter related information. | ||
| pcubeLoggerGroup | 1.3.6.1.4.1.5655.2.3.1.1.7 | Logger related information. | ||
| pcubeSubscribersGroup | 1.3.6.1.4.1.5655.2.3.1.1.8 | Subscriber related information. | ||
| pcubeTrafficProcessorGroup | 1.3.6.1.4.1.5655.2.3.1.1.9 | Traffic processors related information. | ||
| pcubePortGroup | 1.3.6.1.4.1.5655.2.3.1.1.10 | Ports related information. | ||
| pcubeTxQueuesGroup | 1.3.6.1.4.1.5655.2.3.1.1.11 | Tx queue related information | ||
| pcubeGlobalControllersGroup | 1.3.6.1.4.1.5655.2.3.1.1.12 | Global controllers related information. | ||
| pcubeApplicationGroup | 1.3.6.1.4.1.5655.2.3.1.1.13 | Application related information. | ||
| pcubeTrafficCountersGroup | 1.3.6.1.4.1.5655.2.3.1.1.14 | Traffic counter related information. | ||
| pcubeAttackGroup | 1.3.6.1.4.1.5655.2.3.1.1.15 | Attacks related information. | ||
| pcubeVasTrafficForwardingGroup | 1.3.6.1.4.1.5655.2.3.1.1.16 | VAS traffic forwarding related information. | ||
| pcubeMplsVpnAutoLearnGroup | 1.3.6.1.4.1.5655.2.3.1.1.17 | MPLS VPN auto learning related information. | ||
| pcubeTrapObjectsGroup | 1.3.6.1.4.1.5655.2.3.1.1.18 | Notifications' objects group. | ||
| pcubeSeCompliances | 1.3.6.1.4.1.5655.2.3.1.2 | |||
| pcubeCompliance | 1.3.6.1.4.1.5655.2.3.1.2.1 | A compliance statement defined in this MIB module, for SCE SNMP agents. with old deprectated groups. This compliance includes deprecated groups. | ||
| pcubeComplianceRev1 | 1.3.6.1.4.1.5655.2.3.1.2.2 | A compliance statement defined in this MIB module, for SCE SNMP agents. | ||
| pcubeSeEventsGroup | 1.3.6.1.4.1.5655.2.3.1.3 | Pcube notifications. Contains deprecated objects. | ||
| pcubeSeEventsGroupRev1 | 1.3.6.1.4.1.5655.2.3.1.4 | Pcube notifications. | ||
| pcubeSeEvents | 1.3.6.1.4.1.5655.4.0 | |||
| NTF operationalStatusOperationalTrap | 1.3.6.1.4.1.5655.4.0.1 | OperationalStatusOperational notification signifies that the agent entity has detected the sysOperationalStatus object in this MIB has changed to 'operational(3)'. | ||
| NTF operationalStatusWarningTrap | 1.3.6.1.4.1.5655.4.0.2 | OperationalStatusWarning notification signifies that the agent entity has detected the sysOperationalStatus object in this MIB has changed to 'warning(4)'. | ||
| NTF operationalStatusFailureTrap | 1.3.6.1.4.1.5655.4.0.3 | OperationalStatusFailure notification signifies that the agent entity has detected the sysOperationalStatus object in this MIB has changed to 'failure(5)'. | ||
| NTF systemResetTrap | 1.3.6.1.4.1.5655.4.0.4 | A systemReset notification signifies that the agent entity is about to reset itself either per user's request or due to a fatal event. | ||
| NTF chassisTempAlarmOnTrap | 1.3.6.1.4.1.5655.4.0.5 | A chassisTempAlarmOn notification signifies that the agent entity has detected the chassisTempAlarm object in this MIB has changed to the 'on(3)' state (temperature is too high). | ||
| NTF chassisTempAlarmOffTrap | 1.3.6.1.4.1.5655.4.0.6 | A chassisTempAlarmOff notification signifies that the agent entity has detected the chassisTempAlarm object in this MIB has changed to the 'off(2)' state (temperature level is back to normal). | ||
| NTF chassisVoltageAlarmOnTrap | 1.3.6.1.4.1.5655.4.0.7 | A chassisVoltageAlarmOn notification signifies that the agent entity has detected the chassisVoltageAlarm object in this MIB has changed to the 'on(3)' state (voltage level is too high). | ||
| NTF chassisFansAlarmOnTrap | 1.3.6.1.4.1.5655.4.0.8 | A chassisFanStatusFailure notification signifies that the agent entity has detected the chassisFansAlarm object in this MIB has changed to the 'on(3)' state. | ||
| NTF chassisPowerSupplyAlarmOnTrap | 1.3.6.1.4.1.5655.4.0.9 | A chassisPsuStatusFailure notification signifies that the agent entity has detected the chassisPowerSupplyAlarm object in this MIB has changed to the 'on(3)' state. | ||
| NTF rdrActiveConnectionTrap | 1.3.6.1.4.1.5655.4.0.10 | RdrConnectionDestTypeActive notification signifies that the agent entity has detected the rdrFormatterDestStatus object in this MIB has changed to the 'active(2)' state. | ||
| NTF rdrNoActiveConnectionTrap | 1.3.6.1.4.1.5655.4.0.11 | A rdrNoActiveConnection notification signifies that the agent entity has detected there is no active connection between the RDR-formatter and any Data Collector. | ||
| NTF rdrConnectionUpTrap | 1.3.6.1.4.1.5655.4.0.12 | RdrConnectionStatusUp notification signifies that the agent entity has detected the rdrFormatterDestConnectionStatus object in this MIB has changed to 'up(2)'. | ||
| NTF rdrConnectionDownTrap | 1.3.6.1.4.1.5655.4.0.13 | RdrConnectionStatusDown notification signifies that the agent entity has detected the rdrFormatterDestConnectionStatus object in this MIB has changed to 'down(3)'. | ||
| NTF telnetSessionStartedTrap | 1.3.6.1.4.1.5655.4.0.14 | Replaced by the more generic sessionStartedTrap. | ||
| NTF telnetSessionEndedTrap | 1.3.6.1.4.1.5655.4.0.15 | Replaced by the more generic sessionEndedTrap. | ||
| NTF telnetSessionDeniedAccessTrap | 1.3.6.1.4.1.5655.4.0.16 | Replaced by the more generic sessionDeniedAccessTrap. | ||
| NTF telnetSessionBadLoginTrap | 1.3.6.1.4.1.5655.4.0.17 | Replaced by the more generic sessionBadLoginTrap. | ||
| NTF loggerUserLogIsFullTrap | 1.3.6.1.4.1.5655.4.0.18 | A loggerUserLogIsFull notification signifies that the agent entity has detected the User log file is full. In such case the agent entity rolls to the next file. | ||
| NTF sntpClockDriftWarnTrap | 1.3.6.1.4.1.5655.4.0.19 | An sntpClockDriftWarn notification signifies that the entity's SNTP agent did not receive time update for a long period, this may cause a time drift. | ||
| NTF linkModeBypassTrap | 1.3.6.1.4.1.5655.4.0.20 | A linkModeBypass notification signifies that the agent entity has detected that the linkOperMode object in this MIB has changed to 'bypass(2)'. | ||
| NTF linkModeForwardingTrap | 1.3.6.1.4.1.5655.4.0.21 | A linkModeForwarding notification signifies that the agent entity has detected that the linkOperMode object in this MIB has changed to 'forwarding(3)'. | ||
| NTF linkModeCutoffTrap | 1.3.6.1.4.1.5655.4.0.22 | A linkModeCutoff notification signifies that the agent entity has detected that the linkOperMode object in this MIB has changed to 'cutoff(4)'. | ||
| STR pcubeSeEventGenericString1 | 1.3.6.1.4.1.5655.4.0.23 | SnmpAdminString | read-only | Temporary string used for traps. Always returns an empty string. |
| STR pcubeSeEventGenericString2 | 1.3.6.1.4.1.5655.4.0.24 | SnmpAdminString | read-only | Temporary string used for traps. Always returns an empty string. |
| NTF moduleAttackFilterActivatedTrap | 1.3.6.1.4.1.5655.4.0.25 | A moduleAttackFilterActivated notification signifies that the agent entity's attack filter module has activated a filter. The pcubeSeEventGenericString1 is the type of attack-filter, which was activated. | ||
| NTF moduleAttackFilterDeactivatedTrap | 1.3.6.1.4.1.5655.4.0.26 | A portAttackFilterDeactivated notification signifies that the agent entity's attack filter module has removed a filter that was previously activated. The pcubeSeEventGenericString1 is the attack-filter type, which was sent in the corresponding moduleAttackFilterActivatedTrap. the pcubeSeEventGenericString2 is the reason for deactivating the filter. | ||
| NTF moduleEmAgentGenericTrap | 1.3.6.1.4.1.5655.4.0.27 | A generic notification used by the P-Cube EM agent. pcubeSeEventGenericString1 specifies what notification is it, and pcubeSeEventGenericString2 is the relevant parameter. | ||
| NTF linkModeSniffingTrap | 1.3.6.1.4.1.5655.4.0.28 | A linkModeSniffing notification signifies that the agent entity has detected that the linkOperMode object in this MIB has changed to 'sniffing(5)'. | ||
| NTF moduleRedundancyReadyTrap | 1.3.6.1.4.1.5655.4.0.29 | A moduleRedundancyReady notification signifies that the module was able to connect and synchronize with a redundant entity, and is now ready to handle fail-over if needed. | ||
| NTF moduleRedundantConfigurationMismatchTrap | 1.3.6.1.4.1.5655.4.0.30 | A moduleRedundantConfigurationMismatch notification signifies that the module was not able to synchronize with a redundant entity, due to a essential configuration parameters that are do not match between the module and the redundant entity. | ||
| NTF moduleLostRedundancyTrap | 1.3.6.1.4.1.5655.4.0.31 | A moduleLostRedundancy notification signifies that the module has lost the ability to perform the fail-over procedure. | ||
| NTF moduleSmConnectionDownTrap | 1.3.6.1.4.1.5655.4.0.32 | A moduleSmConnectionDown notification signifies that the module's virtual connection to the subscriber manager is broken. | ||
| NTF moduleSmConnectionUpTrap | 1.3.6.1.4.1.5655.4.0.33 | A moduleSmConnectionUp notification signifies that the module's virtual connection to the subscriber manager is up and working. | ||
| NTF moduleOperStatusChangeTrap | 1.3.6.1.4.1.5655.4.0.34 | A moduleOperStatusChangeTrap notification signifies that the moduleOperStatus has changed its value. | ||
| NTF portOperStatusChangeTrap | 1.3.6.1.4.1.5655.4.0.35 | A portOperStatusChangeTrap notification signifies that the portOperStatus object of the portIndex has changed its value, i.e., the link was forced down or the force down was released. | ||
| NTF chassisLineFeedAlarmOnTrap | 1.3.6.1.4.1.5655.4.0.36 | A chassisLineFeedAlarmOn notification signifies that the agent entity has detected the chassisLineFeed object in this MIB has changed to the 'on(3)' state. | ||
| NTF rdrFormatterCategoryDiscardingReportsTrap | 1.3.6.1.4.1.5655.4.0.37 | rdrCategoryDiscardingReportsTrap notification signifies that the agent entity has detected that reports send to this category are being discarded. The rdrFormatterCategoryNumReportsDiscarded object in this MIB is counting the amount of discarded reports. | ||
| NTF rdrFormatterCategoryStoppedDiscardingReportsTrap | 1.3.6.1.4.1.5655.4.0.38 | rdrCategoryStoppedDiscardingReportsTrap notification signifies that the agent entity has detected that reports send to this category are not being discarded any more. The rdrFormatterCategoryNumReportsDiscarded object in this MIB is counting the amount of discarded reports. | ||
| NTF sessionStartedTrap | 1.3.6.1.4.1.5655.4.0.39 | A sessionStarted notification signifies that the agent entity has accepted a new session. The pcubeSeEventGenericString1 is the session type (telnet/SSH) and client IP address. | ||
| NTF sessionEndedTrap | 1.3.6.1.4.1.5655.4.0.40 | A sessionEnded notification signifies that the agent entity has detected end of a session. The pcubeSeEventGenericString1 is the session type (telnet/SSH) and client IP address. | ||
| NTF sessionDeniedAccessTrap | 1.3.6.1.4.1.5655.4.0.41 | A sessionDeniedAccess notification signifies that the agent entity has refused a session from unauthorized source. The pcubeSeEventGenericString1 is the session type (telnet/SSH) and client IP address. | ||
| NTF sessionBadLoginTrap | 1.3.6.1.4.1.5655.4.0.42 | A sessionBadLogin notification signifies that the agent entity has detected attempt to login with a wrong password. The pcubeSeEventGenericString1 is the session type (telnet/SSH) and client IP address. | ||
| NTF illegalSubscriberMappingTrap | 1.3.6.1.4.1.5655.4.0.43 | A illegalSubscriberMappingTrap notification signifies that some external entity has attempted to create illegal or inconsistent subscriber mappings. The pcubeSeEventGenericString1 contains a message describing the problem. | ||
| NTF loggerLineAttackLogFullTrap | 1.3.6.1.4.1.5655.4.0.44 | Signifies that the agent entity has detected the line-attack log file is full. In such case the agent entity rolls to the next file. | ||
| NTF vasServerOpertionalStatusChangeTrap | 1.3.6.1.4.1.5655.4.0.45 | Signifies that the agent entity has detected that the vas server operational status has changed. | ||
| I32 pullRequestNumber | 1.3.6.1.4.1.5655.4.0.46 | Integer32 | read-only | Used only for traps to signify the number of pull requests issued so far for the anonymous subscriber given in the pullRequestRetryFailedTrap containing notification. A direct get will always returns 0. |
| NTF pullRequestRetryFailedTrap | 1.3.6.1.4.1.5655.4.0.47 | Signifies that an unknown subscriber wasn't identified after a certain number of pull requests. The value of pcubeSeEventGenericString1 is the subscriber id and the pullRequestNumber is the number of pull requests made on this sub. | ||
| NTF mplsVpnTotalHWMappingsThresholdExceededTrap | 1.3.6.1.4.1.5655.4.0.48 | Sent when the value of mplsVpnCurrentHWMappings exceeds the allowed threshold. | ||
| pcubeSEObjs | 1.3.6.1.4.1.5655.4.1 | |||
| systemGrp | 1.3.6.1.4.1.5655.4.1.1 | |||
| INT sysOperationalStatus | 1.3.6.1.4.1.5655.4.1.1.1 | INTEGER | read-only | Indicates the operational status of the system. |
| INT sysFailureRecovery | 1.3.6.1.4.1.5655.4.1.1.2 | INTEGER | read-only | Indicates if the system should enter a Failure mode after abnormal boot. |
| STR sysVersion | 1.3.6.1.4.1.5655.4.1.1.3 | SnmpAdminString | read-only | The system version. |
| pchassisGrp | 1.3.6.1.4.1.5655.4.1.2 | |||
| INT pchassisSysType | 1.3.6.1.4.1.5655.4.1.2.1 | INTEGER | read-only | The chassis system type. |
| INT pchassisPowerSupplyAlarm | 1.3.6.1.4.1.5655.4.1.2.2 | INTEGER | read-only | Indicates if the power supply to the chassis is normal. If the status is not 'ok' it means that one or more power supplies are not functional. |
| INT pchassisFansAlarm | 1.3.6.1.4.1.5655.4.1.2.3 | INTEGER | read-only | Indicates if all the fans on the chassis are functional. |
| INT pchassisTempAlarm | 1.3.6.1.4.1.5655.4.1.2.4 | INTEGER | read-only | The chassis temperature alarm status. |
| INT pchassisVoltageAlarm | 1.3.6.1.4.1.5655.4.1.2.5 | INTEGER | read-only | The chassis internal voltage alarm status. If the alarm is 'on' it indicates that the voltage level of one or more HW units is not in the normal range. |
| I32 pchassisNumSlots | 1.3.6.1.4.1.5655.4.1.2.6 | Integer32 | read-only | Indicates the number of slots in the chassis available for plug-in modules. This number counts slots that are already occupied as well as empty slots. |
| I32 pchassisSlotConfig | 1.3.6.1.4.1.5655.4.1.2.7 | Integer32 | read-only | An indication of which slots in the chassis have modules inserted. This is an integer value with bits set to indicate configured modules. It can be interpreted as a sum of f(x) as x goes from 1 to the number of slots, where f(x) = 0 for no module inserted and f(x) = exp(2, x-1) for a module inserted. |
| INT pchassisPsuType | 1.3.6.1.4.1.5655.4.1.2.8 | INTEGER | read-only | Indicates the type of the power supplies. |
| INT pchassisLineFeedAlarm | 1.3.6.1.4.1.5655.4.1.2.10 | INTEGER | read-only | Indicates if the line feed to the chassis is normal. If the status is not 'ok' it means that one or more line feeds are not connected or have no power. |
| pmoduleGrp | 1.3.6.1.4.1.5655.4.1.3 | |||
| pmoduleTable | 1.3.6.1.4.1.5655.4.1.3.1 | not-accessible | A list of module entries. The number of entries is the number of modules in the chassis. | |
| pmoduleEntry | 1.3.6.1.4.1.5655.4.1.3.1.1 | not-accessible | Entry containing information about one module in the chassis. | |
| I32 pmoduleIndex | 1.3.6.1.4.1.5655.4.1.3.1.1.1 | Integer32 | read-only | A unique value for each module within the chassis. |
| INT pmoduleType | 1.3.6.1.4.1.5655.4.1.3.1.1.2 | INTEGER | read-only | The type of module. |
| I32 pmoduleNumTrafficProcessors | 1.3.6.1.4.1.5655.4.1.3.1.1.3 | Integer32 | read-only | The number of traffic processors supported by this module. |
| I32 pmoduleSlotNum | 1.3.6.1.4.1.5655.4.1.3.1.1.4 | Integer32 | read-only | This value is determined by the chassis slot number where this module is located. Valid entries are 1 to the value of chassisNumSlots. |
| STR pmoduleHwVersion | 1.3.6.1.4.1.5655.4.1.3.1.1.5 | SnmpAdminString | read-only | The hardware version of the module. |
| I32 pmoduleNumPorts | 1.3.6.1.4.1.5655.4.1.3.1.1.6 | Integer32 | read-only | The number of ports supported by this module. |
| I32 pmoduleNumLinks | 1.3.6.1.4.1.5655.4.1.3.1.1.7 | Integer32 | read-only | The number of links carrying inband traffic that are supported by this module. Link is uniquely defined by the two ports that are at its end-points. |
| INT pmoduleConnectionMode | 1.3.6.1.4.1.5655.4.1.3.1.1.8 | INTEGER | read-only | Indicates the connection mode of a module. |
| STR pmoduleSerialNumber | 1.3.6.1.4.1.5655.4.1.3.1.1.9 | SnmpAdminString | read-only | Indicates the serial number of the module. |
| TIK pmoduleUpStreamAttackFilteringTime | 1.3.6.1.4.1.5655.4.1.3.1.1.10 | TimeTicks | read-only | Indicates the accumulated time which attack up-stream traffic was filtered. |
| TIK pmoduleUpStreamLastAttackFilteringTime | 1.3.6.1.4.1.5655.4.1.3.1.1.11 | TimeTicks | read-only | Indicates the time since the previous attack was filtered in the up-stream traffic. |
| TIK pmoduleDownStreamAttackFilteringTime | 1.3.6.1.4.1.5655.4.1.3.1.1.12 | TimeTicks | read-only | Indicates the accumulated time which attack down-stream traffic was filtered. |
| TIK pmoduleDownStreamLastAttackFilteringTime | 1.3.6.1.4.1.5655.4.1.3.1.1.13 | TimeTicks | read-only | Indicates the time since the previous attack was filtered in the down-stream traffic. |
| TIK pmoduleAttackObjectsClearTime | 1.3.6.1.4.1.5655.4.1.3.1.1.14 | TimeTicks | read-write | Indicates the time since the attack objects were cleared. Writing a 0 to this object causes the counters to be cleared. |
| INT pmoduleAdminStatus | 1.3.6.1.4.1.5655.4.1.3.1.1.15 | INTEGER | read-only | Indicates configuration of a module in respect to whether the module should handle traffic. |
| INT pmoduleOperStatus | 1.3.6.1.4.1.5655.4.1.3.1.1.16 | INTEGER | read-only | Indicates current module's role in respect to whether the module handles traffic. |
| linkGrp | 1.3.6.1.4.1.5655.4.1.4 | |||
| linkTable | 1.3.6.1.4.1.5655.4.1.4.1 | not-accessible | The Link table provides information regarding the configuration and status of the links that pass through the SE and carry inband traffic. The number of entries in this table is determined by the number of modules in the chassis and the number of links on each module. | |
| linkEntry | 1.3.6.1.4.1.5655.4.1.4.1.1 | not-accessible | Entry containing information about the Link. | |
| I32 linkModuleIndex | 1.3.6.1.4.1.5655.4.1.4.1.1.1 | Integer32 | read-only | An index value that uniquely identifies the module where this link is located. |
| I32 linkIndex | 1.3.6.1.4.1.5655.4.1.4.1.1.2 | Integer32 | read-only | An index value that uniquely identifies this link within a module. Valid entries are 1 to the value of moduleNumLinks for this module. |
| LIN linkAdminModeOnActive | 1.3.6.1.4.1.5655.4.1.4.1.1.3 | LinkModeType | read-only | The desired mode of the link when the module's operating status is Active and the module is not in boot or failure. The possible modes are bypass, forwarding and sniffing. In bypass mode the traffic is forwarded from one port to the other using an internal splitter. In forwarding mode the traffic is forwarded through the internal hardware and software modules of the SE. In sniffing mode the traffic is passed in the same manner as in bypass mode, however a copy of the traffic is made and analyzed internally in the box. |
| LIN linkAdminModeOnFailure | 1.3.6.1.4.1.5655.4.1.4.1.1.4 | LinkModeType | read-only | The desired mode of the link when the system's operational status is Failure. The possible modes are Bypass and Cutoff. In Bypass mode the traffic is forwarded from one port to the other using an internal splitter. In Cutoff mode the traffic is dropped by the SE. |
| LIN linkOperMode | 1.3.6.1.4.1.5655.4.1.4.1.1.5 | LinkModeType | read-only | The operational mode of the link. In Bypass mode the traffic is forwarded from one port to the other using an internal splitter. In Forwarding mode the traffic is forwarded through the internal software and hardware modules of the SCE. In Sniffing mode the traffic is forwarded in the same manner as in Bypass mode, however the traffic is passed through the internal software and hardware modules of the SCE for analyzing. in Cutoff mode the traffic is dropped by the SCE platform. |
| INT linkStatusReflectionEnable | 1.3.6.1.4.1.5655.4.1.4.1.1.6 | INTEGER | read-only | Indicates if failure of the physical link on one i/f should trigger the failure of the link on the other i/f. |
| I32 linkSubscriberSidePortIndex | 1.3.6.1.4.1.5655.4.1.4.1.1.7 | Integer32 | read-only | An index value that uniquely identifies this link with its related port that is connected to the subscriber side. |
| I32 linkNetworkSidePortIndex | 1.3.6.1.4.1.5655.4.1.4.1.1.8 | Integer32 | read-only | An index value that uniquely identifies this link with its related port that is connected to the network side. |
| diskGrp | 1.3.6.1.4.1.5655.4.1.5 | |||
| U32 diskNumUsedBytes | 1.3.6.1.4.1.5655.4.1.5.1 | Unsigned32 | read-only | The number of used bytes. |
| U32 diskNumFreeBytes | 1.3.6.1.4.1.5655.4.1.5.2 | Unsigned32 | read-only | The number of free bytes. |
| rdrFormatterGrp | 1.3.6.1.4.1.5655.4.1.6 | |||
| INT rdrFormatterEnable | 1.3.6.1.4.1.5655.4.1.6.1 | INTEGER | read-only | Indicates whether the RDR-formatter is enabled or disabled. When the RDR-formatter is enabled, it sends the reports it gets from the traffic processors to the Data Collector as defined in the rdrFormatterDestTable. |
| rdrFormatterDestTable | 1.3.6.1.4.1.5655.4.1.6.2 | not-accessible | The RDR-formatter destinations table (0 to 3 entries). This table lists the addresses of Data Collectors. If the RDR-formatter is enabled, the destination with the highest priority that a TCP connection to it can be established would receive the reports generated by the traffic processors. | |
| rdrFormatterDestEntry | 1.3.6.1.4.1.5655.4.1.6.2.1 | not-accessible | A destination table entry. | |
| IP rdrFormatterDestIPAddr | 1.3.6.1.4.1.5655.4.1.6.2.1.1 | IpAddress | read-only | The IP address of a Data Collector. |
| I32 rdrFormatterDestPort | 1.3.6.1.4.1.5655.4.1.6.2.1.2 | Integer32 | read-only | The TCP port on which the Data Collector listens. |
| I32 rdrFormatterDestPriority | 1.3.6.1.4.1.5655.4.1.6.2.1.3 | Integer32 | read-only | The priority given to the Data Collector. The active Data Collector is the Data Collector with the highest priority and a TCP connection that is up. |
| INT rdrFormatterDestStatus | 1.3.6.1.4.1.5655.4.1.6.2.1.4 | INTEGER | read-only | In 'redundancy(2)' and in 'simpleLoadBalancing(3)' rdrFormatterForwardingMode there can be only one 'active' destination, which is where the reports are currently being sent to. In 'multicast(4)' modes all destinations will receive the active(2) status. |
| INT rdrFormatterDestConnectionStatus | 1.3.6.1.4.1.5655.4.1.6.2.1.5 | INTEGER | read-only | Indicates the status of TCP connection to this destination. |
| U32 rdrFormatterDestNumReportsSent | 1.3.6.1.4.1.5655.4.1.6.2.1.6 | Unsigned32 | read-only | Indicates the number of reports sent by the RDR-formatter to this destination. |
| U32 rdrFormatterDestNumReportsDiscarded | 1.3.6.1.4.1.5655.4.1.6.2.1.7 | Unsigned32 | read-only | Indicates the number of reports dropped by the RDR-formatter on this destination. |
| U32 rdrFormatterDestReportRate | 1.3.6.1.4.1.5655.4.1.6.2.1.8 | Unsigned32 | read-only | Indicates the rate of the reports (in reports per second) currently sent to this destination. |
| U32 rdrFormatterDestReportRatePeak | 1.3.6.1.4.1.5655.4.1.6.2.1.9 | Unsigned32 | read-only | Indicates the maximum report rate sent to this destination. |
| TIK rdrFormatterDestReportRatePeakTime | 1.3.6.1.4.1.5655.4.1.6.2.1.10 | TimeTicks | read-only | Indicates the time since the rdrFormatterDestReportRatePeak value occurred. |
| U32 rdrFormatterNumReportsSent | 1.3.6.1.4.1.5655.4.1.6.3 | Unsigned32 | read-only | Indicates the number of reports sent by the RDR-formatter. |
| U32 rdrFormatterNumReportsDiscarded | 1.3.6.1.4.1.5655.4.1.6.4 | Unsigned32 | read-only | Indicates the number of reports dropped by the RDR-formatter. |
| TIK rdrFormatterClearCountersTime | 1.3.6.1.4.1.5655.4.1.6.5 | TimeTicks | read-write | The time since RDR-formatter counters were last cleared. Writing a 0 to this object causes the RDR-formatter counters to be cleared. |
| U32 rdrFormatterReportRate | 1.3.6.1.4.1.5655.4.1.6.6 | Unsigned32 | read-only | Indicates the rate of the reports (in reports per second) currently sent to all of the destinations. |
| U32 rdrFormatterReportRatePeak | 1.3.6.1.4.1.5655.4.1.6.7 | Unsigned32 | read-only | Indicates the maximum report rate sent to all of the destinations. |
| TIK rdrFormatterReportRatePeakTime | 1.3.6.1.4.1.5655.4.1.6.8 | TimeTicks | read-only | Indicates the time since the rdrFormatterReportRatePeak value occurred. |
| INT rdrFormatterProtocol | 1.3.6.1.4.1.5655.4.1.6.9 | INTEGER | read-only | Indicates the RDR protocol currently in use. |
| INT rdrFormatterForwardingMode | 1.3.6.1.4.1.5655.4.1.6.10 | INTEGER | read-only | Indicates the mode of how the RDR formatter sends the reports to its destinations. |
| rdrFormatterCategoryTable | 1.3.6.1.4.1.5655.4.1.6.11 | not-accessible | The RDR-formatter Category table. Describes the different categories of RDRs and RDR destination groups. | |
| rdrFormatterCategoryEntry | 1.3.6.1.4.1.5655.4.1.6.11.1 | not-accessible | A category table entry. | |
| I32 rdrFormatterCategoryIndex | 1.3.6.1.4.1.5655.4.1.6.11.1.1 | Integer32 | read-only | The category number. |
| STR rdrFormatterCategoryName | 1.3.6.1.4.1.5655.4.1.6.11.1.2 | SnmpAdminString | read-only | The name given to this category. |
| U32 rdrFormatterCategoryNumReportsSent | 1.3.6.1.4.1.5655.4.1.6.11.1.3 | Unsigned32 | read-only | Indicates the number of reports sent by the RDR-formatter to this category. |
| U32 rdrFormatterCategoryNumReportsDiscarded | 1.3.6.1.4.1.5655.4.1.6.11.1.4 | Unsigned32 | read-only | Indicates the number of reports dropped by the RDR-formatter on this category. |
| U32 rdrFormatterCategoryReportRate | 1.3.6.1.4.1.5655.4.1.6.11.1.5 | Unsigned32 | read-only | Indicates the rate of the reports (in reports per second) currently sent to this category. |
| U32 rdrFormatterCategoryReportRatePeak | 1.3.6.1.4.1.5655.4.1.6.11.1.6 | Unsigned32 | read-only | Indicates the maximum report rate sent to this category. |
| TIK rdrFormatterCategoryReportRatePeakTime | 1.3.6.1.4.1.5655.4.1.6.11.1.7 | TimeTicks | read-only | Indicates the time since the rdrFormatterCategoryReportRatePeak value occurred. |
| U32 rdrFormatterCategoryNumReportsQueued | 1.3.6.1.4.1.5655.4.1.6.11.1.8 | Unsigned32 | read-only | Indicates the amount of pending reports in this category. |
| rdrFormatterCategoryDestTable | 1.3.6.1.4.1.5655.4.1.6.12 | not-accessible | The RDR-formatter Category destinations table. This table lists the addresses of Data Collectors. If the RDR-formatter is enabled, the destination with the highest priority that a TCP connection to it can be established would receive the reports generated by the traffic processors. | |
| rdrFormatterCategoryDestEntry | 1.3.6.1.4.1.5655.4.1.6.12.1 | not-accessible | A destination table entry. | |
| I32 rdrFormatterCategoryDestPriority | 1.3.6.1.4.1.5655.4.1.6.12.1.1 | Integer32 | read-only | The priority given to the Data Collector for this category. The active Data Collector is the Data Collector with the highest priority and a TCP connection that is up. |
| INT rdrFormatterCategoryDestStatus | 1.3.6.1.4.1.5655.4.1.6.12.1.2 | INTEGER | read-only | In modes 'redundancy(2)' and in 'simpleLoadBalancing(3)' there can be only one 'active' destination, which is the destination to which reports are being sent. In 'multicast(4)' modes all destination will receive the 'active(2)' status. |
| loggerGrp | 1.3.6.1.4.1.5655.4.1.7 | |||
| INT loggerUserLogEnable | 1.3.6.1.4.1.5655.4.1.7.1 | INTEGER | read-only | Indicates whether the logging of user information is enabled or disabled. |
| U32 loggerUserLogNumInfo | 1.3.6.1.4.1.5655.4.1.7.2 | Unsigned32 | read-only | Indicates the number of Info messages logged into the user log file since last reboot or last time the counter was cleared. |
| U32 loggerUserLogNumWarning | 1.3.6.1.4.1.5655.4.1.7.3 | Unsigned32 | read-only | Indicates the number of Warning messages logged into the user log file since last reboot or last time the counter was cleared. |
| U32 loggerUserLogNumError | 1.3.6.1.4.1.5655.4.1.7.4 | Unsigned32 | read-only | Indicates the number of Error messages logged into the user log file since last reboot or last time the counter was cleared. |
| U32 loggerUserLogNumFatal | 1.3.6.1.4.1.5655.4.1.7.5 | Unsigned32 | read-only | Indicates the number of Fatal messages logged into the User-Log since last reboot or last time the counter was cleared. |
| TIK loggerUserLogClearCountersTime | 1.3.6.1.4.1.5655.4.1.7.6 | TimeTicks | read-write | The time since user log counters were last cleared. Writing a 0 to this object causes the user log counters to be cleared. |
| subscribersGrp | 1.3.6.1.4.1.5655.4.1.8 | |||
| subscribersInfoTable | 1.3.6.1.4.1.5655.4.1.8.1 | not-accessible | The subscribers information table consists of data regarding subscribers management operations performed. | |
| subscribersInfoEntry | 1.3.6.1.4.1.5655.4.1.8.1.1 | not-accessible | A SubscribersInfoEntry entry. | |
| U32 subscribersNumIntroduced | 1.3.6.1.4.1.5655.4.1.8.1.1.1 | Unsigned32 | read-only | Indicates the current number of subscribers introduced to the SCE. These subscribers may or may not have IP address or VLAN mappings. Subscribers who do not have mappings of any kind cannot be associated with traffic, thus will be served by the SCE according to the default settings. |
| U32 subscribersNumFree | 1.3.6.1.4.1.5655.4.1.8.1.1.2 | Unsigned32 | read-only | Indicates the number of subscribers that may be introduced in addition to the subscribers that are already introduced to the SCE (subscribersNumIntroduced). |
| U32 subscribersNumIpAddrMappings | 1.3.6.1.4.1.5655.4.1.8.1.1.3 | Unsigned32 | read-only | Indicates the current number of 'IP address to subscriber' mappings. |
| U32 subscribersNumIpAddrMappingsFree | 1.3.6.1.4.1.5655.4.1.8.1.1.4 | Unsigned32 | read-only | Indicates the number of free 'IP address to subscriber' mappings that may be used for defining new mappings. |
| U32 subscribersNumIpRangeMappings | 1.3.6.1.4.1.5655.4.1.8.1.1.5 | Unsigned32 | read-only | Indicates the current number of 'IP-range to subscriber' mappings. |
| U32 subscribersNumIpRangeMappingsFree | 1.3.6.1.4.1.5655.4.1.8.1.1.6 | Unsigned32 | read-only | Indicates the number of free 'IP-range to subscriber' mappings that may be used for defining new mappings. |
| U32 subscribersNumVlanMappings | 1.3.6.1.4.1.5655.4.1.8.1.1.7 | Unsigned32 | read-only | Indicates the current number of VLAN to subscribers mappings. |
| U32 subscribersNumVlanMappingsFree | 1.3.6.1.4.1.5655.4.1.8.1.1.8 | Unsigned32 | read-only | Indicates the number of free 'VLAN to subscriber' mappings that may be used for defining new mappings. |
| U32 subscribersNumActive | 1.3.6.1.4.1.5655.4.1.8.1.1.9 | Unsigned32 | read-only | Indicates the current number of active subscribers, these subscribers necessarily have an IP address or VLAN mappings that define the traffic that should be associated and served according to the subscriber service agreement. |
| U32 subscribersNumActivePeak | 1.3.6.1.4.1.5655.4.1.8.1.1.10 | Unsigned32 | read-only | Indicates the peak value of subscribersNumActive since the last time it was cleared or the system started. |
| TIK subscribersNumActivePeakTime | 1.3.6.1.4.1.5655.4.1.8.1.1.11 | TimeTicks | read-only | Indicates the time since the subscribersNumActivePeak value occurred. |
| U32 subscribersNumUpdates | 1.3.6.1.4.1.5655.4.1.8.1.1.12 | Unsigned32 | read-only | Indicates the accumulated number of subscribers database updates received by the SCE. |
| TIK subscribersCountersClearTime | 1.3.6.1.4.1.5655.4.1.8.1.1.13 | TimeTicks | read-write | Indicates the time since the subscribers counters were cleared. Writing a 0 to this object causes the counters to be cleared. |
| U32 subscribersNumTpIpRanges | 1.3.6.1.4.1.5655.4.1.8.1.1.14 | Unsigned32 | read-only | Indicates the current number of 'Traffic Processor IP ranges' used. |
| U32 subscribersNumTpIpRangesFree | 1.3.6.1.4.1.5655.4.1.8.1.1.15 | Unsigned32 | read-only | Indicates the number of free 'Traffic Processor IP ranges'. |
| U32 subscribersNumAnonymous | 1.3.6.1.4.1.5655.4.1.8.1.1.16 | Unsigned32 | read-only | Indicates the current number of anonymous subscribers. |
| U32 subscribersNumWithSessions | 1.3.6.1.4.1.5655.4.1.8.1.1.17 | Unsigned32 | read-only | Indicates the current number of subscribers with open sessions. |
| subscribersPropertiesTable | 1.3.6.1.4.1.5655.4.1.8.2 | not-accessible | The subscribers properties table provides the list of properties available for each subscriber. | |
| subscribersPropertiesEntry | 1.3.6.1.4.1.5655.4.1.8.2.1 | not-accessible | A subscribersPropertiesTable entry. | |
| I32 spIndex | 1.3.6.1.4.1.5655.4.1.8.2.1.1 | Integer32 | read-only | An index value that uniquely identify the property. |
| STR spName | 1.3.6.1.4.1.5655.4.1.8.2.1.2 | SnmpAdminString | read-only | Subscriber property name. |
| STR spType | 1.3.6.1.4.1.5655.4.1.8.2.1.3 | SnmpAdminString | read-only | Subscriber application property type in respect to: variable type (integer, boolean, string etc), number of elements (scalar or array) and restrictions if any exist. |
| subscribersPropertiesValueTable | 1.3.6.1.4.1.5655.4.1.8.3 | not-accessible | The subscribers properties value table is used to provide subscriber properties values for subscribers introduced into the SCE. An entry must be created by setting the entry's spvRowStatus object with createAndGo (4) before setting any other of the entry's objects. To specify the subscriber's property set the spvSubName and spvPropertyName objects. The spvPropertyName must be one of the properties from the subscribersPropertiesTable. To remove an entry set the spvRowStatus object with destroy (6). To poll the subscriber property the manager need to poll the spvPropertyStringValue, the spvPropertyUintValue or the spvPropertyCounter64Value objects. The table is cleared when the application is unloaded. | |
| subscribersPropertiesValueEntry | 1.3.6.1.4.1.5655.4.1.8.3.1 | not-accessible | A subscribersPropertiesValueTable entry. | |
| I32 spvIndex | 1.3.6.1.4.1.5655.4.1.8.3.1.1 | Integer32 | not-accessible | A index to the table. |
| STR spvSubName | 1.3.6.1.4.1.5655.4.1.8.3.1.2 | SnmpAdminString | read-create | A name that uniquely identifies the subscriber. |
| STR spvPropertyName | 1.3.6.1.4.1.5655.4.1.8.3.1.3 | SnmpAdminString | read-create | A name that uniquely identifies the subscriber property. Array type properties may be accessed each element at a time in C like format, e.g. x[1], or y[1][2]. |
| ROW spvRowStatus | 1.3.6.1.4.1.5655.4.1.8.3.1.4 | RowStatus | read-create | This object controls creation of a table entry. Only setting the createAndGo (4) and destroy (6) will change the status of the entry. |
| STR spvPropertyStringValue | 1.3.6.1.4.1.5655.4.1.8.3.1.5 | SnmpAdminString | read-only | The value of the subscriber property in string format. |
| U32 spvPropertyUintValue | 1.3.6.1.4.1.5655.4.1.8.3.1.6 | Unsigned32 | read-only | The value of the subscriber property in unsigned integer. If the property can't be casted to unsigned integer this object returns zero. |
| C64 spvPropertyCounter64Value | 1.3.6.1.4.1.5655.4.1.8.3.1.7 | Counter64 | read-only | The value of the subscriber property in Counter64. If the property can't be casted to Counter64 this object returns zero. |
| trafficProcessorGrp | 1.3.6.1.4.1.5655.4.1.9 | |||
| tpInfoTable | 1.3.6.1.4.1.5655.4.1.9.1 | not-accessible | The Traffic Processor Info table consists of data regarding traffic handled by the traffic processors by classification of packets and flows. | |
| tpInfoEntry | 1.3.6.1.4.1.5655.4.1.9.1.1 | not-accessible | A tpInfoTable entry. | |
| I32 tpModuleIndex | 1.3.6.1.4.1.5655.4.1.9.1.1.1 | Integer32 | read-only | An index value that uniquely identifies the module where this traffic processor is located. |
| I32 tpIndex | 1.3.6.1.4.1.5655.4.1.9.1.1.2 | Integer32 | read-only | An index value that uniquely identifies this traffic processor within a module. The value is determined by the location of the traffic processor on the module. Valid entries are 1 to the value of moduleNumTrafficProcessors for this module. |
| U32 tpTotalNumHandledPackets | 1.3.6.1.4.1.5655.4.1.9.1.1.3 | Unsigned32 | read-only | Indicates the accumulated number of packets handled by this traffic processor since last reboot or last time this counter was cleared. |
| U32 tpTotalNumHandledFlows | 1.3.6.1.4.1.5655.4.1.9.1.1.4 | Unsigned32 | read-only | Indicates the accumulated number of flows handled by this traffic Processor since last reboot or last time this counter was cleared. |
| U32 tpNumActiveFlows | 1.3.6.1.4.1.5655.4.1.9.1.1.5 | Unsigned32 | read-only | Indicates the number of flows currently being handled by this traffic processor. |
| U32 tpNumActiveFlowsPeak | 1.3.6.1.4.1.5655.4.1.9.1.1.6 | Unsigned32 | read-only | Indicates the peak value of tpNumActiveFlows since the last time it was cleared or the system started. |
| TIK tpNumActiveFlowsPeakTime | 1.3.6.1.4.1.5655.4.1.9.1.1.7 | TimeTicks | read-only | Indicates the time since the tpNumActiveFlowsPeak value occurred. |
| U32 tpNumTcpActiveFlows | 1.3.6.1.4.1.5655.4.1.9.1.1.8 | Unsigned32 | read-only | Indicates the number of TCP flows currently being handled by this traffic processor. |
| U32 tpNumTcpActiveFlowsPeak | 1.3.6.1.4.1.5655.4.1.9.1.1.9 | Unsigned32 | read-only | Indicates the peak value of tpNumTcpActiveFlows since the last time it was cleared or the system started. |
| TIK tpNumTcpActiveFlowsPeakTime | 1.3.6.1.4.1.5655.4.1.9.1.1.10 | TimeTicks | read-only | Indicates the time since the tpNumTcpActiveFlowsPeak value occurred. |
| U32 tpNumUdpActiveFlows | 1.3.6.1.4.1.5655.4.1.9.1.1.11 | Unsigned32 | read-only | Indicates the number of UDP flows currently being handled by this traffic processor. |
| U32 tpNumUdpActiveFlowsPeak | 1.3.6.1.4.1.5655.4.1.9.1.1.12 | Unsigned32 | read-only | Indicates the peak value of tpNumUdpActiveFlows since the last time it was cleared or the system started. |
| TIK tpNumUdpActiveFlowsPeakTime | 1.3.6.1.4.1.5655.4.1.9.1.1.13 | TimeTicks | read-only | Indicates the time since the tpNumUdpActiveFlowsPeak value occurred. |
| U32 tpNumNonTcpUdpActiveFlows | 1.3.6.1.4.1.5655.4.1.9.1.1.14 | Unsigned32 | read-only | Indicates the number of non TCP/UDP flows currently being handled by this traffic processor. |
| U32 tpNumNonTcpUdpActiveFlowsPeak | 1.3.6.1.4.1.5655.4.1.9.1.1.15 | Unsigned32 | read-only | Indicates the peak value of tpNumNonTcpUdpActiveFlows since the last time it was cleared or the system started. |
| TIK tpNumNonTcpUdpActiveFlowsPeakTime | 1.3.6.1.4.1.5655.4.1.9.1.1.16 | TimeTicks | read-only | Indicates the time since the tpNumNonTcpUdpActiveFlowsPeak value occurred. |
| U32 tpTotalNumBlockedPackets | 1.3.6.1.4.1.5655.4.1.9.1.1.17 | Unsigned32 | read-only | Indicates the accumulated number of packets discarded by this traffic processor according to application blocking rules. |
| U32 tpTotalNumBlockedFlows | 1.3.6.1.4.1.5655.4.1.9.1.1.18 | Unsigned32 | read-only | Indicates the accumulated number of flows discarded by this traffic processor according to application blocking rules. |
| U32 tpTotalNumDiscardedPacketsDueToBwLimit | 1.3.6.1.4.1.5655.4.1.9.1.1.19 | Unsigned32 | read-only | Indicates the accumulated number of packets discarded by this traffic processor due to subscriber bandwidth limitations. |
| U32 tpTotalNumWredDiscardedPackets | 1.3.6.1.4.1.5655.4.1.9.1.1.20 | Unsigned32 | read-only | Indicates the accumulated number of packets discarded by this traffic processor due to congestion in the queues. |
| U32 tpTotalNumFragments | 1.3.6.1.4.1.5655.4.1.9.1.1.21 | Unsigned32 | read-only | Indicates the accumulated number of fragmented packets handled by this traffic processor. |
| U32 tpTotalNumNonIpPackets | 1.3.6.1.4.1.5655.4.1.9.1.1.22 | Unsigned32 | read-only | Indicates the accumulated number of non IP packets handled by this traffic processor. |
| U32 tpTotalNumIpCrcErrPackets | 1.3.6.1.4.1.5655.4.1.9.1.1.23 | Unsigned32 | read-only | Indicates the accumulated number of packets with IP CRC error handled by this traffic processor. |
| U32 tpTotalNumIpLengthErrPackets | 1.3.6.1.4.1.5655.4.1.9.1.1.24 | Unsigned32 | read-only | Indicates the accumulated number of packets with IP length error handled by this traffic processor. |
| U32 tpTotalNumIpBroadcastPackets | 1.3.6.1.4.1.5655.4.1.9.1.1.25 | Unsigned32 | read-only | Indicates the accumulated number of IP broadcast packets handled by this traffic processor. |
| U32 tpTotalNumTtlErrPackets | 1.3.6.1.4.1.5655.4.1.9.1.1.26 | Unsigned32 | read-only | Indicates the accumulated number of packets with TTL error handled by this traffic processor. |
| U32 tpTotalNumTcpUdpCrcErrPackets | 1.3.6.1.4.1.5655.4.1.9.1.1.27 | Unsigned32 | read-only | Indicates the accumulated number of TCP/UDP packets with CRC error handled by this traffic processor. |
| TIK tpClearCountersTime | 1.3.6.1.4.1.5655.4.1.9.1.1.28 | TimeTicks | read-write | Indicates the time since the traffic processor statistics counters were last cleared. Writing a 0 to this object causes the traffic processor counters to be cleared. |
| U32 tpHandledPacketsRate | 1.3.6.1.4.1.5655.4.1.9.1.1.29 | Unsigned32 | read-only | Indicates the rate in packets per second of the packets handled by this traffic processor. |
| U32 tpHandledPacketsRatePeak | 1.3.6.1.4.1.5655.4.1.9.1.1.30 | Unsigned32 | read-only | Indicates the peak value of tpHandledPacketsRate since the last time it was cleared or the system started. |
| TIK tpHandledPacketsRatePeakTime | 1.3.6.1.4.1.5655.4.1.9.1.1.31 | TimeTicks | read-only | Indicates the time since the tpHandledPacketsRatePeak value occurred. |
| U32 tpHandledFlowsRate | 1.3.6.1.4.1.5655.4.1.9.1.1.32 | Unsigned32 | read-only | Indicates the rate in flows opening per second of the flows handled by this traffic processor. |
| U32 tpHandledFlowsRatePeak | 1.3.6.1.4.1.5655.4.1.9.1.1.33 | Unsigned32 | read-only | Indicates the peak value of tpHandledFlowsRate since the last time it was cleared or the system started. |
| TIK tpHandledFlowsRatePeakTime | 1.3.6.1.4.1.5655.4.1.9.1.1.34 | TimeTicks | read-only | Indicates the time since the tpHandledFlowsRatePeakTime value occurred. |
| I32 tpCpuUtilization | 1.3.6.1.4.1.5655.4.1.9.1.1.35 | Integer32 | read-only | Indicates the percentage of CPU utilization, updated once every 2 minutes. |
| I32 tpCpuUtilizationPeak | 1.3.6.1.4.1.5655.4.1.9.1.1.36 | Integer32 | read-only | Indicates the peak value of tpCpuUtilization since the last time it was cleared or the system started. |
| TIK tpCpuUtilizationPeakTime | 1.3.6.1.4.1.5655.4.1.9.1.1.37 | TimeTicks | read-only | Indicates the time since the tpCpuUtilizationPeak value occurred. |
| I32 tpFlowsCapacityUtilization | 1.3.6.1.4.1.5655.4.1.9.1.1.38 | Integer32 | read-only | Indicates the percentage of flows capacity utilization. |
| I32 tpFlowsCapacityUtilizationPeak | 1.3.6.1.4.1.5655.4.1.9.1.1.39 | Integer32 | read-only | Indicates the peak value of tpFlowsCapacityUtilization since the last time it was cleared or the system started. |
| TIK tpFlowsCapacityUtilizationPeakTime | 1.3.6.1.4.1.5655.4.1.9.1.1.40 | TimeTicks | read-only | Indicates the time since the tpFlowsCapacityUtilizationPeak value occurred. |
| I32 tpServiceLoss | 1.3.6.1.4.1.5655.4.1.9.1.1.41 | Integer32 | read-only | Indicates the relative amount of service loss in this traffic Processor, in units of 0.001%, since last reboot or last time this counter was cleared. |
| pportGrp | 1.3.6.1.4.1.5655.4.1.10 | |||
| pportTable | 1.3.6.1.4.1.5655.4.1.10.1 | not-accessible | A list of port entries. The number of entries is determined by the number of modules in the chassis and the number of ports on each module. | |
| pportEntry | 1.3.6.1.4.1.5655.4.1.10.1.1 | not-accessible | Entry containing information for a particular port on a module. | |
| I32 pportModuleIndex | 1.3.6.1.4.1.5655.4.1.10.1.1.1 | Integer32 | read-only | An index value that uniquely identifies the module where this port is located. |
| I32 pportIndex | 1.3.6.1.4.1.5655.4.1.10.1.1.2 | Integer32 | read-only | An index value that uniquely identifies this port within a module. The value is determined by the location of the port on the module. Valid entries are 1 to the value of moduleNumPorts for this module. |
| INT pportType | 1.3.6.1.4.1.5655.4.1.10.1.1.3 | INTEGER | read-only | The type of physical layer medium dependent interface on the port. |
| I32 pportNumTxQueues | 1.3.6.1.4.1.5655.4.1.10.1.1.4 | Integer32 | read-only | The number of transmit queues supported by this port. |
| I32 pportIfIndex | 1.3.6.1.4.1.5655.4.1.10.1.1.5 | Integer32 | read-only | The value of the instance of the ifIndex object, defined in MIB-II, for this port. |
| INT pportAdminSpeed | 1.3.6.1.4.1.5655.4.1.10.1.1.6 | INTEGER | read-only | The desired speed of the port. The current operational speed of the port can be determined from ifSpeed. |
| INT pportAdminDuplex | 1.3.6.1.4.1.5655.4.1.10.1.1.7 | INTEGER | read-only | The desired duplex of the port. |
| INT pportOperDuplex | 1.3.6.1.4.1.5655.4.1.10.1.1.8 | INTEGER | read-only | Indicates whether the port is operating in half-duplex or full-duplex. |
| I32 pportLinkIndex | 1.3.6.1.4.1.5655.4.1.10.1.1.9 | Integer32 | read-only | Indicates the linkIndex of the link that this port belongs to. Value of 0 indicates that this port is not associated with any link. Value of -1 indicates that this port is associated to multiple links. |
| INT pportOperStatus | 1.3.6.1.4.1.5655.4.1.10.1.1.10 | INTEGER | read-only | Indicates the status of the port and if the port is down indicates the reason. |
| txQueuesGrp | 1.3.6.1.4.1.5655.4.1.11 | |||
| txQueuesTable | 1.3.6.1.4.1.5655.4.1.11.1 | not-accessible | This table consists of information on the SCE's transmit queues. | |
| txQueuesEntry | 1.3.6.1.4.1.5655.4.1.11.1.1 | not-accessible | A txQueuesTable entry. | |
| I32 txQueuesModuleIndex | 1.3.6.1.4.1.5655.4.1.11.1.1.1 | Integer32 | read-only | An index value that uniquely identifies the module where this queue is located. |
| I32 txQueuesPortIndex | 1.3.6.1.4.1.5655.4.1.11.1.1.2 | Integer32 | read-only | An index value that uniquely identifies the port where this queue is located. |
| I32 txQueuesQueueIndex | 1.3.6.1.4.1.5655.4.1.11.1.1.3 | Integer32 | read-only | An index value that uniquely identifies this queue within a port. The value is determined by the location of the queue on the port. Valid entries are 1 to the value of portNumTxQueues for this module. |
| STR txQueuesDescription | 1.3.6.1.4.1.5655.4.1.11.1.1.4 | SnmpAdminString | read-only | Description of the transmit queue. |
| I32 txQueuesBandwidth | 1.3.6.1.4.1.5655.4.1.11.1.1.5 | Integer32 | read-only | The bandwidth in L1 kbps configured for this queue. |
| I32 txQueuesUtilization | 1.3.6.1.4.1.5655.4.1.11.1.1.6 | Integer32 | read-only | The percentage of bandwidth utilization relative to the configured rate. |
| I32 txQueuesUtilizationPeak | 1.3.6.1.4.1.5655.4.1.11.1.1.7 | Integer32 | read-only | Indicates the peak value of txQueuesUtilization since the last time it was cleared or the system started. |
| TIK txQueuesUtilizationPeakTime | 1.3.6.1.4.1.5655.4.1.11.1.1.8 | TimeTicks | read-only | Indicates the time since the txQueuesUtilizationPeak value occurred. |
| TIK txQueuesClearCountersTime | 1.3.6.1.4.1.5655.4.1.11.1.1.9 | TimeTicks | read-write | Indicates the time since the TX queues statistics counters were last cleared. Writing a 0 to this object causes the TX queues counters to be cleared. |
| C64 txQueuesDroppedBytesEx | 1.3.6.1.4.1.5655.4.1.11.1.1.10 | Counter64 | read-only | Amount of dropped L3 bytes. This is valid only if the system is configured to count dropped bytes per TX queue. |
| globalControllersGrp | 1.3.6.1.4.1.5655.4.1.12 | |||
| globalControllersTable | 1.3.6.1.4.1.5655.4.1.12.1 | not-accessible | This table consists of information on the SCE's Global Controllers. note: the globalControllersIndex and the SCE CLI configuration index have a offset of one i.e. 1 in the MIB refers to 0 in the CLI. | |
| globalControllersEntry | 1.3.6.1.4.1.5655.4.1.12.1.1 | not-accessible | A globalControllersTable entry. | |
| I32 globalControllersModuleIndex | 1.3.6.1.4.1.5655.4.1.12.1.1.1 | Integer32 | read-only | An index value that uniquely identifies the module where this controller is located. |
| I32 globalControllersPortIndex | 1.3.6.1.4.1.5655.4.1.12.1.1.2 | Integer32 | read-only | An index value that uniquely identifies the port where this controller is located. |
| I32 globalControllersIndex | 1.3.6.1.4.1.5655.4.1.12.1.1.3 | Integer32 | read-only | An index value that uniquely identifies this controller within a port. |
| STR globalControllersDescription | 1.3.6.1.4.1.5655.4.1.12.1.1.4 | SnmpAdminString | read-only | Description of the controller. |
| I32 globalControllersBandwidth | 1.3.6.1.4.1.5655.4.1.12.1.1.5 | Integer32 | read-only | The L1 bandwidth configured for this controller. |
| I32 globalControllersUtilization | 1.3.6.1.4.1.5655.4.1.12.1.1.6 | Integer32 | read-only | The percentage of bandwidth utilization relative to the configured rate. |
| I32 globalControllersUtilizationPeak | 1.3.6.1.4.1.5655.4.1.12.1.1.7 | Integer32 | read-only | Indicates the peak value of globalControllersUtilization since the last time it was cleared or the system started. |
| TIK globalControllersUtilizationPeakTime | 1.3.6.1.4.1.5655.4.1.12.1.1.8 | TimeTicks | read-only | Indicates the time since the globalControllersUtilizationPeak value occurred. |
| TIK globalControllersClearCountersTime | 1.3.6.1.4.1.5655.4.1.12.1.1.9 | TimeTicks | read-write | Indicates the time since the controllers statistics counters were last cleared. Writing a 0 to this object causes the controllers counters to be cleared. |
| C64 globalControllersDroppedBytes | 1.3.6.1.4.1.5655.4.1.12.1.1.10 | Counter64 | read-only | Amount of L3 dropped bytes. This is valid only if the system is configured to count dropped bytes per global controller. |
| applicationGrp | 1.3.6.1.4.1.5655.4.1.13 | |||
| appInfoTable | 1.3.6.1.4.1.5655.4.1.13.1 | not-accessible | This table consists of information on the SCE's application. | |
| appInfoEntry | 1.3.6.1.4.1.5655.4.1.13.1.1 | not-accessible | A appInfoTable entry. | |
| STR appName | 1.3.6.1.4.1.5655.4.1.13.1.1.1 | SnmpAdminString | read-only | The application name. |
| STR appDescription | 1.3.6.1.4.1.5655.4.1.13.1.1.2 | SnmpAdminString | read-only | The application description. |
| STR appVersion | 1.3.6.1.4.1.5655.4.1.13.1.1.3 | SnmpAdminString | read-only | The application version. |
| appPropertiesTable | 1.3.6.1.4.1.5655.4.1.13.2 | not-accessible | The application properties table provides the list of properties available for the application. The table is cleared when the application is unloaded. | |
| appPropertiesEntry | 1.3.6.1.4.1.5655.4.1.13.2.1 | not-accessible | A appPropertiesTable entry. | |
| I32 apIndex | 1.3.6.1.4.1.5655.4.1.13.2.1.1 | Integer32 | read-only | An index value that uniquely identify the property. |
| STR apName | 1.3.6.1.4.1.5655.4.1.13.2.1.2 | SnmpAdminString | read-only | Application property name. Property can be either scalar or array type. |
| STR apType | 1.3.6.1.4.1.5655.4.1.13.2.1.3 | SnmpAdminString | read-only | Application property type. |
| appPropertiesValueTable | 1.3.6.1.4.1.5655.4.1.13.3 | not-accessible | The applications properties value table is used to provide specific values for the applications properties. An entry must be created by setting the entry's apvRowStatus object with createAndGo (4) before setting the name of the property requested. To specify the property set the apvPropertyName objects. The apvPropertyName must be one of the properties from the appPropertiesTable. To remove an entry set the apvRowStatus object with destroy (6). To poll the application property, poll the apvPropertyStringValue, apvPropertyUintValue, or apvPropertyCounter64Value object. The table is cleared when the application is unloaded. | |
| appPropertiesValueEntry | 1.3.6.1.4.1.5655.4.1.13.3.1 | not-accessible | A appPropertiesValueTable entry. | |
| I32 apvIndex | 1.3.6.1.4.1.5655.4.1.13.3.1.1 | Integer32 | not-accessible | Index to the table. |
| STR apvPropertyName | 1.3.6.1.4.1.5655.4.1.13.3.1.2 | SnmpAdminString | read-create | A name that uniquely identifies the application property. Array type properties may be accessed each element at a time in C like format, e.g. x[1], or y[1][2]. |
| ROW apvRowStatus | 1.3.6.1.4.1.5655.4.1.13.3.1.3 | RowStatus | read-create | This object controls creation of a table entry. |
| STR apvPropertyStringValue | 1.3.6.1.4.1.5655.4.1.13.3.1.4 | SnmpAdminString | read-only | The value of the application property in display string format. |
| U32 apvPropertyUintValue | 1.3.6.1.4.1.5655.4.1.13.3.1.5 | Unsigned32 | read-only | The value of the application property in unsigned integer. If the property can't be casted to unsigned integer this object returns zero. |
| C64 apvPropertyCounter64Value | 1.3.6.1.4.1.5655.4.1.13.3.1.6 | Counter64 | read-only | The value of the application property in Counter64 format. If the property can't be casted to Counter64, getting this object returns zero. |
| trafficCountersGrp | 1.3.6.1.4.1.5655.4.1.14 | |||
| trafficCountersTable | 1.3.6.1.4.1.5655.4.1.14.1 | not-accessible | The Traffic counters table provides information regarding the value of different the traffic counters. | |
| trafficCountersEntry | 1.3.6.1.4.1.5655.4.1.14.1.1 | not-accessible | Entry containing information about a traffic counter. | |
| I32 trafficCounterIndex | 1.3.6.1.4.1.5655.4.1.14.1.1.1 | Integer32 | read-only | An index value that uniquely identifies the counter. |
| C64 trafficCounterValue | 1.3.6.1.4.1.5655.4.1.14.1.1.2 | Counter64 | read-only | A 64 bit counter value. |
| STR trafficCounterName | 1.3.6.1.4.1.5655.4.1.14.1.1.3 | SnmpAdminString | read-only | The name given to this counter. |
| INT trafficCounterType | 1.3.6.1.4.1.5655.4.1.14.1.1.4 | INTEGER | read-only | Defines whether there the traffic counters counts by 'packets(3)' or by 'bytes(2)'. |
| attackGrp | 1.3.6.1.4.1.5655.4.1.15 | |||
| attackTypeTable | 1.3.6.1.4.1.5655.4.1.15.1 | not-accessible | The Attack type table provides information regarding detected attacks, aggregated by attack type. | |
| attackTypeEntry | 1.3.6.1.4.1.5655.4.1.15.1.1 | not-accessible | Entry containing aggregated information about attacks of a given type. | |
| I32 attackTypeIndex | 1.3.6.1.4.1.5655.4.1.15.1.1.1 | Integer32 | read-only | An index value that uniquely identifies the attack type. |
| STR attackTypeName | 1.3.6.1.4.1.5655.4.1.15.1.1.2 | SnmpAdminString | read-only | The name of this attack type. |
| U32 attackTypeCurrentNumAttacks | 1.3.6.1.4.1.5655.4.1.15.1.1.3 | Unsigned32 | read-only | The current amount of attacks detected of this type. |
| U32 attackTypeTotalNumAttacks | 1.3.6.1.4.1.5655.4.1.15.1.1.4 | Unsigned32 | read-only | The total amount of attacks detected of this type since last clear. |
| C64 attackTypeTotalNumFlows | 1.3.6.1.4.1.5655.4.1.15.1.1.5 | Counter64 | read-only | The total amount of flows in attacks detected of this type since last clear. |
| U32 attackTypeTotalNumSeconds | 1.3.6.1.4.1.5655.4.1.15.1.1.6 | Unsigned32 | read-only | The total duration of attacks detected of this type since last clear. |
| vasTrafficForwardingGrp | 1.3.6.1.4.1.5655.4.1.16 | |||
| vasServerTable | 1.3.6.1.4.1.5655.4.1.16.1 | not-accessible | The VAS server Table provides information on each VAS server operational status. | |
| vasServerEntry | 1.3.6.1.4.1.5655.4.1.16.1.1 | not-accessible | Entry containing information about VAS server status. | |
| I32 vasServerIndex | 1.3.6.1.4.1.5655.4.1.16.1.1.1 | Integer32 | read-only | An index value that uniquely identifies a VAS server. |
| I32 vasServerId | 1.3.6.1.4.1.5655.4.1.16.1.1.2 | Integer32 | read-only | The ID of the VAS server. |
| INT vasServerAdminStatus | 1.3.6.1.4.1.5655.4.1.16.1.1.3 | INTEGER | read-only | Indicates only the administrative status of the VAS sever, in order to activate a server it should be also configured with a VLAN and a group. |
| INT vasServerOperStatus | 1.3.6.1.4.1.5655.4.1.16.1.1.4 | INTEGER | read-only | Indicates the operational status of the VAS sever. |
| mplsVpnAutoLearnGrp | 1.3.6.1.4.1.5655.4.1.17 | |||
| mplsVpnSoftwareCountersTable | 1.3.6.1.4.1.5655.4.1.17.1 | not-accessible | The MPLS VPN software counters table provides information on various system software counters related to MPLS VPN auto learn. | |
| mplsVpnSoftwareCountersEntry | 1.3.6.1.4.1.5655.4.1.17.1.1 | not-accessible | Entry containing information about MPLS VPN auto learn SW counters. | |
| I32 mplsVpnMaxHWMappings | 1.3.6.1.4.1.5655.4.1.17.1.1.1 | Integer32 | read-only | The maximum number of MPLS VPN mappings supported by HW (including all kinds of mappings). |
| I32 mplsVpnCurrentHWMappings | 1.3.6.1.4.1.5655.4.1.17.1.1.2 | Integer32 | read-only | The current number of HW MPLS VPN mappings in use. |
RFC description
Provides configuration and runtime status for Cisco Service Control Engine chassis modules and line cards.
Start monitoring Cisco SCE2000/SE100 Service Control Engine platforms with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.