All MIBs › HP-ICF-OSPFV3-MIB
Organization: HP Networking
Last Updated: 2017-05-18
Category: Protocol: OSPF, Routing Protocols, Technology: IPv6, Technology: Routing/L3, Vendor: HP/HPE
Description: HP ICF SNMP MIB for OSPFv3 (IPv6) routing protocol configuration and adjacency state on HP ProCurve Layer 3 switches.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HP-ICF-OSPFV3-MIB?
HP-ICF-OSPFV3-MIB holds Hewlett-Packard's proprietary extensions to the standard OSPFV3-MIB, adding vendor-specific configuration and state objects for the OSPFv3 (IPv6) routing protocol on HP ProCurve Layer 3 switches and routers. It exposes routing-protocol configuration (area, interface, and timer settings) and adjacency/neighbor state rather than hardware sensor data. Its monitoring value is chiefly around software/protocol health — confirming that OSPFv3 neighbor adjacencies are up, transitioning normally, and that area/interface configuration matches intent — rather than physical component status. As its name indicates, it explicitly extends and depends on the standard OSPFV3-MIB defined in IETF RFC 5643, supplementing rather than replacing it. It is deployed in enterprise and campus networks running IPv6 OSPF routing on HP Layer 3 switching/routing platforms. Engineers can download the HP-ICF-OSPFV3-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HP-ICF-OSPFV3-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- HP ProCurve Layer 3 switch/router
Monitoring Examples
The sampled source provided no concrete object names beyond the module's own description, so no specific identifiers can be cited with confidence. In general use, such a module would extend the standard OSPFv3 neighbor and interface tables with HP-specific counters or flags; an administrator would combine these with the base OSPFV3-MIB's adjacency-state objects to detect a neighbor stuck in an exchange/loading state, indicating an IPv6 routing adjacency failure.
What Can Be Monitored
- OSPFv3 neighbor adjacency state
- OSPFv3 interface configuration
- OSPFv3 area configuration
- routing protocol timers
This MIB depends on
Related MIBs
Imported Objects
From HP-ICF-OID
| hpSwitch | OBJECT-IDENTITY |
From HP-ICF-OSPF
| HpicfOspfLogAction | |
| HpicfOspfLogType |
From INET-ADDRESS-MIB
| InetAddressIPv6 |
From OSPF-MIB
| BigMetric | |
| Metric |
From OSPFV3-MIB
| Ospfv3RouterIdTC | |
| ospfv3AreaAggregateEntry | OBJECT-TYPE |
| ospfv3AreaEntry | OBJECT-TYPE |
| ospfv3AreaLsdbAreaId | OBJECT-TYPE |
| ospfv3AreaLsdbEntry | OBJECT-TYPE |
| ospfv3AreaLsdbLsid | OBJECT-TYPE |
| ospfv3AreaLsdbRouterId | OBJECT-TYPE |
| ospfv3AreaLsdbType | OBJECT-TYPE |
| ospfv3AsLsdbEntry | OBJECT-TYPE |
| ospfv3IfEntry | OBJECT-TYPE |
| ospfv3IfIndex | OBJECT-TYPE |
| ospfv3IfInstId | OBJECT-TYPE |
| ospfv3LinkLsdbEntry | OBJECT-TYPE |
| ospfv3LinkLsdbIfIndex | OBJECT-TYPE |
| ospfv3LinkLsdbIfInstId | OBJECT-TYPE |
| ospfv3LinkLsdbLsid | OBJECT-TYPE |
| ospfv3LinkLsdbRouterId | OBJECT-TYPE |
| ospfv3LinkLsdbType | OBJECT-TYPE |
| ospfv3NbrEntry | OBJECT-TYPE |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| TruthValue |
How to Use in IPNetwork Monitor
Example using hpicfOspfv3ASscopeUnknownLsaCount OID:
Select an HP ProCurve Layer 3 switch/router (OSPFv3/IPv6 extensions) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hpicfOspfv3ASscopeUnknownLsaCount into the Find box to locate it in the OID tree, then select it and click OK. The total number of AS-scope unknown link state advertisements received. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hpicfOspfv3MIB | 1.3.6.1.4.1.11.2.14.11.5.1.44 | The MIB module contains HP proprietary extensions to the OSPFV3-MIB module. | ||
| hpicfOspfv3Objects | 1.3.6.1.4.1.11.2.14.11.5.1.44.1 | |||
| hpicfOspfv3GeneralGroup | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1 | |||
| BIG hpicfOspfv3DefaultImportMetric | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.1 | BigMetric | read-write | The default metric used for advertising external routes by this router. |
| INT hpicfOspfv3DefaultImportMetricType | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.2 | INTEGER | read-write | The default metric type used for advertising external routes by this router. |
| I32 hpicfOspfv3IntraAreaDistance | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.3 | Integer32 | read-write | The administrative distance to associate with intra-area routes learned by OSPF. Routes with lower distances are preferred. By default, OSPF routes have an administrative distance of 110. Note that the administrative distance settings for OSPF do not affect the choice of routes within OSPF. OSPF will still prefer intra-area routes over inter-area or AS-external routes even if hpicfOspfv3InterAreaDistance or hpicfOspfv3ExternalDistance is lower than hpicfOspfv3IntraAreaDistance. The appropriate administrative distance value is applied to the route that OSPF selects as its best route to a destination and is used to decide whether OSPF's route is preferred over a route from some other source. |
| I32 hpicfOspfv3InterAreaDistance | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.4 | Integer32 | read-write | The administrative distance to associate with inter-area routes learned by OSPF. Routes with lower distances are preferred. By default, OSPF routes have an administrative distance of 110. Note that the administrative distance settings for OSPF do not affect the choice of routes within OSPF. OSPF will still prefer intra-area routes over inter-area routes, even if hpicfOspfv3InterAreaDistance is lower than hpicfOspfv3IntraAreaDistance. It will also still prefer inter-area routes over AS-external routes even if hpicfOspfv3ExternalDistance is lower than hpicfOspfv3InterAreaDistance. The appropriate administrative distance value is applied to the route that OSPF selects as its best route to a destination and is used to decide whether OSPF's route is preferred over a route from some other source. |
| I32 hpicfOspfv3ExternalDistance | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.5 | Integer32 | read-write | The administrative distance to associate with AS-external routes learned by OSPF. Routes with lower distances are preferred. By default, OSPF routes have an administrative distance of 110. Note that the administrative distance settings for OSPF do not affect the choice of routes within OSPF. OSPF will still prefer intra-area routes and inter-area routes over AS-external routes even if hpicfOspfv3ExternalDistance is lower than the hpicfOspfv3IntraAreaDistance or hpicfOspfv3InterAreaDistance. The appropriate administrative distance value is applied to the route that OSPF selects as its best route to a destination and is used to decide whether OSPF's route is preferred over a route from some other source. |
| I32 hpicfOspfv3SpfThrottleStartInterval | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.7 | Integer32 | read-write | Initial SPF schedule delay |
| I32 hpicfOspfv3SpfThrottleWaitInterval | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.8 | Integer32 | read-write | Minimum wait time between two consecutive SPFs When spf throttle is triggered. |
| I32 hpicfOspfv3SpfThrottleMaxWaitTime | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.9 | Integer32 | read-write | Maximum time between two consecutive SPFs runs when spf throttling active. |
| U32 hpicfOspfv3SpfThrottleCurrentSpfInterval | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.10 | Unsigned32 | read-only | Current dynamic wait interval between SPF computations |
| U32 hpicfOspfv3AreaCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.11 | Unsigned32 | read-only | Number of areas in a router |
| T/F hpicfOspfv3RestartHelper | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.12 | TruthValue | read-only | Graceful restart helper status A value of true (1) indicates that Restart helper is enabled, false(2) indicates that Restart helper is disabled. |
| C32 hpicfOspfv3ASscopeUnknownLsaCountEx | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.13 | Counter32 | read-only | The total number of AS-scope unknown link state advertisements received. |
| C32 hpicfOspfv3LinkLsdbStatLinkLsa | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.14 | Counter32 | read-only | This object indicates total number of Link LSAs in the router. |
| U32 hpicfOspfv3TotalUnknownLsa | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.15 | Unsigned32 | read-only | This object indicates total number of LSAs received with Unknown type. |
| MET hpicfOspfv3ReferenceCost | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.1.16 | Metric | read-write | The reference cost is used as global configuration for internal area cost & vlan cost. |
| hpicfOspfv3AsLsdbTable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.2 | not-accessible | The OSPFv3 AS-Scope Link State Database (LSDB). The LSDB contains the AS-Scope Link State Advertisements from throughout the areas that the device is attached to. | |
| hpicfOspfv3AsLsdbEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.2.1 | not-accessible | A single AS-Scope Link State Advertisement. | |
| BIT hpicfOspfv3AsLsdbEFTFlags | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.2.1.1 | Bits | read-only | A 32-bit integer Representing the E,F and T bit flags |
| MET hpicfOspfv3AsLsdbMetric | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.2.1.2 | Metric | read-only | The cost associated with this route. |
| U32 hpicfOspfv3AsLsdbPrefixLength | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.2.1.3 | Unsigned32 | read-only | The Prefix Length of the Address Prefix. |
| U32 hpicfOspfv3AsLsdbPrefixOptions | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.2.1.4 | Unsigned32 | read-only | The Prefix Options associated with the Address Prefix. |
| U32 hpicfOspfv3AsLsdbRefLsType | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.2.1.5 | Unsigned32 | read-only | If non-zero value, this refers to another LSA type in Link State Database further identified by the Reference Link State ID field |
| ADR hpicfOspfv3AsLsdbAddrPrefix | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.2.1.6 | InetAddressIPv6 | read-only | The advertised 16-byte Address Prefix. |
| ADR hpicfOspfv3AsLsdbFwdingAddress | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.2.1.7 | InetAddressIPv6 | read-only | If included, Data traffic for the advertised destination will be forwarded to this address. |
| U32 hpicfOspfv3AsLsdbExtRouteTags | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.2.1.8 | Unsigned32 | read-only | The 32-bit Route Tag for the advertised Route. |
| U32 hpicfOspfv3AsLsdbRefLsId | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.2.1.9 | Unsigned32 | read-only | The 32-bit Link state ID of the referenced LSA entry. |
| U32 hpicfOspfv3AsLsdbLsaLength | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.2.1.10 | Unsigned32 | read-only | This field describes the length of LSA. |
| hpicfOspfv3AreaLsdbTable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3 | not-accessible | The OSPFv3 Area-Scope link state database. The LSDB contains the Area-Scope Link State Advertisements from throughout the area that the device is attached to. | |
| hpicfOspfv3AreaLsdbEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1 | not-accessible | A single Area-Scope Link State Advertisement. | |
| BIT hpicfOspfv3AreaLsdbRtrCapBits | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.1 | Bits | read-only | This field is valid only for Router LSA. It represents the capabilities of the router in the Area. |
| U32 hpicfOspfv3AreaLsdbOptions | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.2 | Unsigned32 | read-only | The Options field enables OSPF routers to support (or not support) optional capabilities, and to communicate their capability level to other OSPF routers. This field is valid if the LSA is a Router LSA or a Network LSA, or an Inter-Area-Router LSA. |
| MET hpicfOspfv3AreaLsdbMetric | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.3 | Metric | read-only | This field is valid only for Router LSA, a Inter-Area_prefix LSA or a NSSA LSA. This field indicates the cost involved in using the interface or route. |
| U32 hpicfOspfv3AreaLsdbPrefixLength | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.4 | Unsigned32 | read-only | The Prefix Length of the Address Prefix. |
| U32 hpicfOspfv3AreaLsdbPrefixOptions | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.5 | Unsigned32 | read-only | The Prefix Options associated with the Address Prefix. |
| ADR hpicfOspfv3AreaLsdbAddrPrefix | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.6 | InetAddressIPv6 | read-only | The advertised 16-byte Address Prefix. |
| OSP hpicfOspfv3AreaLsdbDstRtrId | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.7 | Ospfv3RouterIdTC | read-only | The Router ID of the router being described by the LSA. This field is valid if the LSA is a Inter-Area-Router LSA. |
| U32 hpicfOspfv3AreaLsdbNumPrefixes | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.8 | Unsigned32 | read-only | This field is valid only for Inter-Area-Prefix LSA and indicates the number of prefixes in the LSA. |
| U32 hpicfOspfv3AreaLsdbRefLsType | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.9 | Unsigned32 | read-only | This field is valid only for Inter-Area-Prefix LSA or a NSSA LSA. If non-zero, an LSA with this LS type is to be associated with this LSA. |
| U32 hpicfOspfv3AreaLsdbRefLsId | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.10 | Unsigned32 | read-only | This field is valid only for Inter-Area-Prefix LSA or a NSSA LSA. This field is included only if the Reference LS Type field is set and identifies the LSA with this Link State ID. |
| OSP hpicfOspfv3AreaLsdbRefAdvRtrId | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.11 | Ospfv3RouterIdTC | read-only | This field is valid only for Inter-Area-Prefix LSA or a NSSA LSA. This field is included only if the Reference LS Type field is set and identifies the LSA having this Router ID as the advertising Router ID. |
| BIT hpicfOspfv3AreaLsdbEFTFlags | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.12 | Bits | read-only | This field is valid only for NSSA LSA. This field represents the E,F and T bit flags |
| ADR hpicfOspfv3AreaLsdbFwdingAddress | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.13 | InetAddressIPv6 | read-only | This field is valid only for NSSA LSA. This field is present only if the 'F' Bit is set in the EFT flags field and if included, the data traffic for the advertised destination will be forwarded to this address. |
| U32 hpicfOspfv3AreaLsdbExtRouteTags | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.14 | Unsigned32 | read-only | This field is valid only for NSSA LSA. This field is present only if the 'T' Bit is set in the EFT flags field. A 32-bit field which may be used to communicate additional information between AS boundary routers. |
| U32 hpicfOspfv3AreaLsdbLsaLength | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.15 | Unsigned32 | read-only | This field describes the length of LSA. |
| C32 hpicfOspfv3AreaLsdbLinks | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.3.1.16 | Counter32 | read-only | This field describes the number of links. |
| hpicfOspfv3LinkLsdbTable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.4 | not-accessible | The OSPFv3 Link-Scope link state database(LSDB) for non-virtual interfaces. The LSDB contains the Link-Scope Link State Advertisements from the interfaces that the device is attached to. | |
| hpicfOspfv3LinkLsdbEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.4.1 | not-accessible | A single Link-Scope Link State Advertisement. | |
| U32 hpicfOspfv3LinkLsdbRtrPriority | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.4.1.1 | Unsigned32 | read-only | This field is the OSPF priority set for this router |
| U32 hpicfOspfv3LinkLsdbOptions | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.4.1.2 | Unsigned32 | read-only | The Options field enables OSPF routers to support (or not support) optional capabilities, and to communicate their capability level to other OSPF routers. |
| ADR hpicfOspfv3LinkLsdbLocalAddress | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.4.1.3 | InetAddressIPv6 | read-only | The advertising router's link local IPv6 address |
| U32 hpicfOspfv3LinkLsdbNumPrefixes | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.4.1.4 | Unsigned32 | read-only | The number of other links on the advertising router |
| U32 hpicfOspfv3LinkLsdbLsaLength | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.4.1.5 | Unsigned32 | read-only | This field describes the length of LSA. |
| hpicfOspfv3IfTable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.5 | not-accessible | The table describes the Ospfv3 interfaces. | |
| hpicfOspfv3IfEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.5.1 | not-accessible | The Entry describes one Ospfv3 interface. | |
| T/F hpicfOspfv3IfPassive | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.5.1.1 | TruthValue | read-create | The passive state configuration of the OSPF interface. In the passive mode no OSPF protocol messages are exchanged on this interface. true (1) - The interface is configured to work in Passive mode false (2) - The interface is configured to work in normal mode. This is the default configuration. Changing the value will cause OSPF to reset on this interface and make necessary adjustments to the link state database. All other operations are not defined and will not affect the state of the protocol. |
| U32 hpicfOspfv3IfNbrCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.5.1.2 | Unsigned32 | read-only | This object specifies the number of OSPFv3 neighbors reachable via this interface. This counter should be incremented when a new neighbor is added in the network in which this interface is present. It should be decremented when a neighbor is disconnected. |
| ADR hpicfOspfv3IfDRAddr | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.5.1.10 | InetAddressIPv6 | read-only | This object specifies link local ipv6 address of Designated Router on the interface. |
| ADR hpicfOspfv3IfBDRAddr | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.5.1.11 | InetAddressIPv6 | read-only | This object specifies link local ipv6 address of Backup Designated Router on the interface. |
| U32 hpicfOspfv3IfHelloDueTime | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.5.1.12 | Unsigned32 | read-only | This object specifies the time remaining for the hello timer for the particular Interface to expire. |
| U32 hpicfOspfv3IfAdjNbrCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.5.1.13 | Unsigned32 | read-only | This object specifies the number of fully adjacent neighbors present on this interface. This counter should be incremented when a new neighbor becomes fully adjacent. It should be decremented when the neighbor goes out from full state. |
| hpicfOspfv3NbrTable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.6 | not-accessible | A table describing all neighbors of the of the OSPFv3 router. | |
| hpicfOspfv3NbrEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.6.1 | not-accessible | The information regarding a single neighbor. | |
| U32 hpicfOspfv3NbrUpTime | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.6.1.1 | Unsigned32 | read-only | This object specifies the time duration in seconds for which the adjacency with a particular neighbor is active. This should be a monotonically increasing timer for the duration till the adjacency is active. This counter should be reset on losing and re-establishing an adjacency |
| U32 hpicfOspfv3NbrTimeToExpiry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.6.1.2 | Unsigned32 | read-only | This object specifies the time remaining for the dead timer for the particular neighbor to expire. This counter thus specifies the time in seconds left for an adjacency to be brought down in case no hello packet is received during that interval. |
| G32 hpicfOspfv3NbrDataBaseSummary | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.6.1.3 | Gauge32 | read-only | The number of Link State Advertisements (LSA) sent in Database Description (DD)packet. |
| G32 hpicfOspfv3NbrLinkStateRequest | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.6.1.4 | Gauge32 | read-only | The number of Link State Advertisements (LSA) in link state request list. |
| INT hpicfOspfv3NbrRestartState | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.6.1.5 | INTEGER | read-only | Describes the Graceful Restart(GR) state. normal(0) - Indicates normal status helper(1) - Helper indicates the router is helping another router which is currently in graceful restart. |
| hpicfOspfv3IfStatsTable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.7 | not-accessible | Table that contains OSPFv3 Interface traffic specific statistics. | |
| hpicfOspfv3IfStatsEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.7.1 | not-accessible | A list of statistics counters maintained for an OSPFv3 interface traffic information. | |
| C32 hpicfOspfv3IfSentHelloPkt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.7.1.1 | Counter32 | read-only | The number of OSPFv3 Hello packets sent on the interface. This number is incremented each time an OSPFv3 Hello packet is sent out of an OSPFv3 enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using 'clear ipv6 ospf3 statistics' command |
| C32 hpicfOspfv3IfSentDDPkt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.7.1.2 | Counter32 | read-only | The number of Database Description packets sent on the interface. This number is incremented each time an OSPFv3 DD packet is sent out of an OSPFv3 enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using 'clear ipv6 ospf3 statistics' command |
| C32 hpicfOspfv3IfSentLSRPkt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.7.1.3 | Counter32 | read-only | The number of Link State Request packets sent on the interface. This number is incremented each time OSPFv3 LSR packet is sent out of an OSPFv3 enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using 'clear ipv6 ospf3 statistics' command |
| C32 hpicfOspfv3IfSentLSUPkt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.7.1.4 | Counter32 | read-only | The number of Link State Update packets sent on the interface. This number is incremented each time OSPFv3 LSU packet is sent out of an OSPFv3 enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using 'clear ipv6 ospf3 statistics' command. |
| C32 hpicfOspfv3IfSentLSAPkt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.7.1.5 | Counter32 | read-only | The number of Link State Acknowledgement packet sent on the interface. This number is incremented each time OSPFv3 LS Ack packet is sent out of an OSPFv3 enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using 'clear ipv6 ospf3 statistics' command. |
| C32 hpicfOspfv3IfRcvdHelloPkt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.7.1.6 | Counter32 | read-only | The number of Hello packets received on the interface. This number is incremented each time a hello packet is received on OSPFv3 enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using 'clear ipv6 ospf3 statistics' command |
| C32 hpicfOspfv3IfRcvdDDPkt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.7.1.7 | Counter32 | read-only | The number of Database Description packets received on the interface. This number is incremented each time a OSPFv3 DD packet is received on OSPFv3 enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using 'clear ipv6 ospf3 statistics' command |
| C32 hpicfOspfv3IfRcvdLSRPkt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.7.1.8 | Counter32 | read-only | The number of Link State Request packets received on the interface. This number is incremented each time a OSPFv3 LSR packet is received on OSPFv3 enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using 'clear ipv6 ospf3 statistics' command |
| C32 hpicfOspfv3IfRcvdLSUPkt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.7.1.9 | Counter32 | read-only | The number of Link State Update packets received on the interface. This number is incremented each time an OSPFv3 LSU packet is received on OSPFv3 enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using 'clear ipv6 ospf3 statistics' command |
| C32 hpicfOspfv3IfRcvdLSAPkt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.7.1.10 | Counter32 | read-only | The number of Link State Acknowledgement packets received on the interface. This number is incremented each time a OSPF LS Ack packet is received on OSPFv3 enabled interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using 'clear ipv6 ospf3 statistics' command |
| C32 hpicfOspfv3IfSentTotalErrorCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.7.1.11 | Counter32 | read-only | This refers to the number of erroneous packets discarded on an OSPFv3 interface while sending errors. Discontinuities in the value of this counter can occur at re-initialization of the management system. |
| C32 hpicfOspfv3IfRcvdTotalErrorCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.7.1.12 | Counter32 | read-only | This refers to the number of erroneous packets received on an OSPFv3 interface. Discontinuities in the value of this counter can occur at re-initialization of the management system. |
| hpicfOspfv3IfErrorTable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.8 | not-accessible | Table that contains OSPFv3 Interface traffic specific error information. | |
| hpicfOspfv3IfErrorEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.8.1 | not-accessible | A list of error counters maintained for an OSPFv3 interface. | |
| I32 hpicfOspfv3IfErrorType | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.8.1.1 | Integer32 | not-accessible | This refers to the type of errors in the OSPFv3 packet received on an OSPFv3 enabled interface. |
| C32 hpicfOspfv3IfErrorCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.8.1.2 | Counter32 | read-only | This refers to the number of erroneous packets received on an OSPFv3 interface for each error type. Discontinuities in the value of this counter can occur at re-initialization of the management system. The counters can be cleared for any interface using 'clear ipv6 ospf3 statistics' command. |
| hpicfOspfv3IfClearStatsTable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.9 | not-accessible | A list used to clear statistics information maintained for an OSPFv3 interface. | |
| hpicfOspfv3IfClearStatsEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.9.1 | not-accessible | A list used to clear statistics information maintained for an OSPFv3 interface. | |
| T/F hpicfOspfv3ClearCounters | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.9.1.1 | TruthValue | read-write | When this variable is set to true for a given vlan interface, corresponding interface counters will be cleared. Read of this will always be false. |
| hpicfOspfv3SpfTable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.10 | not-accessible | Table that contains OSPFv3 SPF execution details. | |
| hpicfOspfv3SpfEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.10.1 | not-accessible | A list of OSPFv3 SPF algorithm execution details. | |
| U32 hpicfOspfv3SpfIndex | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.10.1.1 | Unsigned32 | not-accessible | The index in spf table. This can range from 1 to 100 as only last hundred SPF run's reasons will be saved. |
| U32 hpicfOspfv3SpfReason | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.10.1.2 | Unsigned32 | read-only | The hpicfOspfv3SpfReason refers to the reasons for scheduling an SPF run. The Reasons could be OSPFv3 initialization, adding/deleting interface or link state update received. |
| hpicfOspfv3LogTable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.11 | not-accessible | A table containing the configuration parameters for OSPFv3 event logging. | |
| hpicfOspfv3LogEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.11.1 | not-accessible | The configuration parameters for OSPFv3 event log entry. | |
| HPI hpicfOspfv3LogType | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.11.1.1 | HpicfOspfLogType | not-accessible | The type of the event log in OSPFv3 routing protocol . |
| HPI hpicfOspfv3LogAction | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.11.1.2 | HpicfOspfLogAction | read-write | The mode of OSPFv3 event logging. If the OSPFv3 log type is set to neighborAdjacencyChanges, then meaning of this field is as follows: If enabled, it logs only the adjacency state transitions to final states. If enabledWithDetail option, it logs all the state transitions and other events and error conditions related to adjacency. If disabled, none of the adjacency related events are logged. |
| hpicfOspfv3RouterLSATable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.12 | not-accessible | This table represents details advertised in router LSA in addition to area LSDB table. | |
| hpicfOspfv3RouterLSAEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.12.1 | not-accessible | A single Area-Scope Link State Advertisement. | |
| U32 hpicfOspfv3RouterLSANbrIfId | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.12.1.1 | Unsigned32 | not-accessible | The Interface Id of the neighbor. |
| OSP hpicfOspfv3RouterLSANbrRtrId | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.12.1.2 | Ospfv3RouterIdTC | not-accessible | The Router ID the of the neighbor router. |
| U32 hpicfOspfv3RouterLSAIfType | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.12.1.3 | Unsigned32 | read-only | The kind of interface being described. One of the following: Type Description --------------------------------------------------- 1 Point-to-point connection to another router 2 Connection to a transit network 3 Reserved 4 Virtual link . |
| U32 hpicfOspfv3RouterLSAMetric | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.12.1.4 | Unsigned32 | read-only | The cost of using this router interface for outbound traffic. |
| U32 hpicfOspfv3RouterLSAIfId | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.12.1.5 | Unsigned32 | read-only | The Interface ID assigned to the interface being described. |
| hpicfOspfv3NetworkLSATable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.13 | not-accessible | This table represents details advertised in a Network LSA in addition to area LSDB table. | |
| hpicfOspfv3NetworkLSAEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.13.1 | not-accessible | A single Area-Scope Link State Advertisement. | |
| U32 hpicfOspfv3NetworkLSASeqNum | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.13.1.1 | Unsigned32 | not-accessible | The 32-bit LSA sequence number. |
| OSP hpicfOspfv3NetworkLSAAttachedRouter | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.13.1.2 | Ospfv3RouterIdTC | read-only | The 32-bit Router identifier of the attached Router. |
| hpicfOspfv3IntraAPLSATable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.14 | not-accessible | This table represents details advertised in Intra AP LSA in addition to area LSDB table. | |
| hpicfOspfv3IntraAPLSAEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.14.1 | not-accessible | A single Area-Scope Link State Advertisement. | |
| ADR hpicfOspfv3IntraAPAddrPrefix | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.14.1.1 | InetAddressIPv6 | not-accessible | The advertised 16-byte Address Prefix. |
| U32 hpicfOspfv3IntraAPPrefixLength | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.14.1.2 | Unsigned32 | not-accessible | The Prefix Length of the Address Prefix. |
| U32 hpicfOspfv3IntraAPPrefixOptions | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.14.1.3 | Unsigned32 | read-only | The Prefix Options associated with the Address Prefix. |
| MET hpicfOspfv3IntraAPMetric | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.14.1.4 | Metric | read-only | The Cost associated with the Address Prefix. |
| hpicfOspfv3LinkLSATable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.15 | not-accessible | This table represents details advertised in link LSA in addition to link LSDB table. | |
| hpicfOspfv3LinkLSAEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.15.1 | not-accessible | A single Link-Scope Link State Advertisement. | |
| ADR hpicfOspfv3LinkAddrPrefix | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.15.1.1 | InetAddressIPv6 | not-accessible | The address prefix of link advertised in link LSA. |
| U32 hpicfOspfv3LinkPrefixLength | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.15.1.2 | Unsigned32 | not-accessible | The Prefix Length of the Address Prefix. |
| U32 hpicfOspfv3LinkPrefixOptions | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.15.1.3 | Unsigned32 | read-only | The Prefix Options associated with the Address Prefix. |
| hpicfOspfv3Trap | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.16 | |||
| hpicfOspfv3Traps | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.16.0 | |||
| hpicfOspfv3TrapControl | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.16.1 | |||
| OCT hpicfOspfv3SetTrap | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.16.1.1 | OCTET STRING | read-write | A four-octet string serving as a bit map for the trap events defined by the OSPFv3 traps. This object is used to enable or disable specific OSPFv3 traps where a 1 in the bit field represents enabled. The right-most bit (least significant) represents trap 0. Trap Name BitMap ---------------------------------------- OSPFV3_IF_STATE_CHANGE 0x00001 OSPFV3_VIRT_IF_STATE_CHANGE 0x00002 OSPFV3_NBR_STATE_CHANGE 0x00004 OSPFV3_VIRT_NBR_STATE_CHANGE 0x00008 OSPFV3_INTF_CONFIG_ERROR 0x00010 OSPFV3_VIRT_INTF_CONFIG_ERROR 0x00020 OSPFV3_INTF_RCV_BAD_PKT 0x00040 OSPFV3_VIRT_INTF_RCV_BAD_PKT 0x00080 OSPFV3_RST_STATUS 0x20000 OSPFV3_NBR_RST_HELP_STATUS 0x40000 OSPFV3_VIRT_NBR_RST_HELP_STAT 0x80000 OSPFV3_ALL_TRAPS 0xE00FF |
| hpicfOspfv3AreaTable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.17 | not-accessible | This table describes Ospfv3 area. | |
| hpicfOspfv3AreaEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.17.1 | not-accessible | The object describes Ospfv3 area. | |
| C32 hpicfOspfv3AreaNbrDownCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.17.1.8 | Counter32 | read-only | This object indicates the number of neighbor routers in this area that are in DOWN state. |
| C32 hpicfOspfv3AreaNbrAttemptCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.17.1.9 | Counter32 | read-only | This object indicates the number of neighbor routers in this area that are in ATTEMPT state. |
| C32 hpicfOspfv3AreaNbrInitCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.17.1.10 | Counter32 | read-only | This object indicates the number of neighbor routers in this area that are in INIT state. |
| C32 hpicfOspfv3AreaNbr2wayCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.17.1.11 | Counter32 | read-only | This object indicates the number of neighbor routers in this area that are in TWO WAY state. |
| C32 hpicfOspfv3AreaNbrExstartCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.17.1.12 | Counter32 | read-only | This object indicates the number of neighbor routers in this area that are in EX-START state. |
| C32 hpicfOspfv3AreaNbrExchangeCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.17.1.13 | Counter32 | read-only | This object indicates the number of neighbor routers in this area that are in EXCHANGE state. |
| C32 hpicfOspfv3AreaNbrLoadingCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.17.1.14 | Counter32 | read-only | This object indicates the number of neighbor routers in this area that are in LOADING state. |
| C32 hpicfOspfv3AreaNbrFullCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.17.1.15 | Counter32 | read-only | This object indicates the number of neighbor routers in this area that are in FULL state. |
| C32 hpicfOspfv3AreaInterfaceCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.17.1.16 | Counter32 | read-only | This object indicates the total number of OSPFv3 interfaces in this area. |
| C32 hpicfOspfv3AreaScopeUnknownLsaCount | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.17.1.17 | Counter32 | read-only | The total number of area-scope unknown link state advertisements in this area's link state database. |
| hpicfOspfv3AreaAggregateTable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.19 | not-accessible | HP proprietary extensions to ospfv3AreaAggregateTable | |
| hpicfOspfv3AreaAggregateEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.19.1 | not-accessible | Each entry is extension of ospfv3AreaAggregateEntry | |
| BIG hpicfOspfv3AreaAggregateCost | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.19.1.1 | BigMetric | read-create | Manually configured cost of the summary advertisement. A value of 0 indicates that the cost calculated by the OSPF standard should be used. Valid costs range from 1-16777215 |
| hpicfOspfv3AreaLsdbStatsTable | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.20 | not-accessible | Table that contains OSPFv3 area link state database statistics specific information. | |
| hpicfOspfv3AreaLsdbStatsEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.20.1 | not-accessible | A list of statistics counters maintained for an OSPFv3 area link state database. | |
| C32 hpicfOspfv3AreaLsdbStatRtrLsaCnt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.20.1.1 | Counter32 | read-only | This object indicates number of router LSA per area. |
| C32 hpicfOspfv3AreaLsdbStatNwLsaCnt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.20.1.2 | Counter32 | read-only | This object indicates number of network LSA per area. |
| C32 hpicfOspfv3AreaLsdbStatInterPreLsaCnt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.20.1.3 | Counter32 | read-only | This object indicates number of inter-area prefix LSA per area. |
| C32 hpicfOspfv3AreaLsdbStatInterRtrLsaCnt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.20.1.4 | Counter32 | read-only | This object indicates number of inter-area router LSA per area. |
| C32 hpicfOspfv3AreaLsdbStatIntraPreLsaCnt | 1.3.6.1.4.1.11.2.14.11.5.1.44.1.20.1.5 | Counter32 | read-only | This object indicates number of intra-area prefix LSA per area. |
| hpicfOspfv3Conformance | 1.3.6.1.4.1.11.2.14.11.5.1.44.2 | |||
| hpicfOspfv3Groups | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.1 | |||
| hpicfOspfv3BasicGroup | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.1.1 | These objects are used for managing/monitoring OSPFv3 global parameters. | ||
| hpicfOspfv3AsLsdbGroup | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.1.2 | These objects are used for OSPFv3 systems that display their AS-scope link state database. | ||
| hpicfOspfv3AreaLsdbGroup | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.1.3 | These objects are used for OSPFv3 systems that display their Area-scope link state database. | ||
| hpicfOspfv3LinkLsdbGroup | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.1.4 | These objects are used for OSPFv3 systems that display their Link-scope link state database for non-virtual interfaces. | ||
| hpicfOspfv3LogGroup | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.1.8 | A collection of objects for configuring the logging of OSPFv3 adjacency related events. | ||
| hpicfOspfv3TrapControlGroup | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.1.9 | A collection of object which is for controlling the hpicfOspfv3Traps. | ||
| hpicfOspfv3AreaGroup | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.1.11 | These Area objects used for managing/monitoring OSPFv3 Areas. | ||
| hpicfOspfv3AreaLsdbStatsGroup | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.1.13 | These lsdb objects used for monitoring OSPFv3 statistics per area. | ||
| hpicfOspfv3NbrGroup1 | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.1.14 | These neighbor objects are used for managing/monitoring OSPFv3 neighbors. | ||
| hpicfOspfv3StatisticGroup1 | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.1.15 | A collection of objects that contain OSPF interface and SPF statistics. | ||
| hpicfOspfv3IfGroup1 | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.1.16 | These interface objects are used for managing/monitoring OSPFv3 interfaces. | ||
| hpicfOspfv3MetricGroup | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.1.17 | Flags to identify global or manual OSPFv3 cost configuration. | ||
| hpicfOspfv3Compliances | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.2 | |||
| hpicfOspfv3Compliance | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.2.1 | The compliance statement | ||
| hpicfOspfv3Compliance2 | 1.3.6.1.4.1.11.2.14.11.5.1.44.2.2.2 | The compliance statement | ||
| hpicfOspfv3IfMetricObjects | 1.3.6.1.4.1.11.2.14.11.5.1.44.4 | |||
| hpicfOspfv3IfMetricTable | 1.3.6.1.4.1.11.2.14.11.5.1.44.4.1 | not-accessible | Extensions to the table that contains OSPF Metric specific information. | |
| hpicfOspfv3IfMetricEntry | 1.3.6.1.4.1.11.2.14.11.5.1.44.4.1.1 | not-accessible | A list of extensions to the information maintained for an OSPF interface. | |
| I32 hpicfOspfv3IfFlagValue | 1.3.6.1.4.1.11.2.14.11.5.1.44.4.1.1.1 | Integer32 | read-write | This flag is defined to know the type of OSPF cost configuration.. -1 : Default configuration. 0 : Manual configuration. 1 : Global configuration (value taken from global). |
RFC description
HP proprietary extensions to OSPFv3 (Open Shortest Path First version 3) for IPv6 routing management.
Start monitoring HP ProCurve Layer 3 switch/router (OSPFv3/IPv6 extensions) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.