GDC-SC800T3-MIB

All MIBs › GDC-SC800T3-MIB

Category: Domain: WAN/TDM, Vendor: GDC

Description: General DataComm SC800 T3 MIB for DS3 interface configuration and performance statistics management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is GDC-SC800T3-MIB?

GDC-SC800T3-MIB is a General DataComm proprietary MIB (built on the shared GDCCMN-MIB/GDCMACRO-MIB framework) for the SC800 T3 channel-service unit, reporting firmware version and network/channel configuration. Its version table reports active/standby firmware revision, stored-firmware status, a switch-active-firmware action, downloading mode, and a flash-erase action, while a channel-configuration table records forced-DCE mode, DTE test mode, and DTE loop timeout, and a network-configuration table records frame type, transmit clock source, AIS loopdown behavior, line type, and idle/transmit-idle status. As a hardware/software-status MIB it lets an administrator confirm firmware revision and audit T3 network-side clocking and framing configuration. It is deployed on General DataComm SC800 T3 channel-service equipment. Engineers can download the GDC-SC800T3-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in GDC-SC800T3-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

General DataComm SC800 T3 channel-service equipment

Monitoring Examples

An administrator checks sc800t3NetworkTransmitClockSource and sc800t3NetworkFrameType to confirm the T3 network side is clocked and framed correctly before troubleshooting a sync problem on a GDC SC800 unit.

What Can Be Monitored

firmware revision
T3 network clocking and framing configuration

Imported Objects

From GDCCMN-MIB

gdc	OBJECT-IDENTITY

From GDCMACRO-MIB

SCinstance

From RFC-1212

OBJECT-TYPE

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
ds3	1.3.6.1.4.1.498.19
sc800t3	1.3.6.1.4.1.498.19.1
STR sc800t3ActiveFirmwareRev	1.3.6.1.4.1.498.19.1.1.2.1.2	DisplayString	read-only	The version number of the firmware currently executing. The format is MM.NN.BB where: MM: Major Revision (0-99) NN: Minor Revision (0-99) BB: Bug Fix Revision (0-99)
sc800t3AIS	1.3.6.1.4.1.498.19.1.5.10
INT sc800t3AISLOCAL	1.3.6.1.4.1.498.19.1.8.1.1.3	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
sc800t3AlarmConfig	1.3.6.1.4.1.498.19.1.7
sc800t3AlarmConfigEntry	1.3.6.1.4.1.498.19.1.7.1.1		not-accessible	An entry in the GDC Alarm Configuration table.
OID sc800t3AlarmConfigIdentifier	1.3.6.1.4.1.498.19.1.7.1.1.2	OBJECT IDENTIFIER	read-only	format: iso.org.dod.internet.private.enterprises.gdc. ds3.sc800t3.sc800t3Alarms.ALM example: 1.3.6.1.4.1.498.19.1.5.ALM where ALM = 1 for sc800t3NoResponse alarm, 2 for sc800t3DiagRxErr alarm, etc., as specified in the Alarm Definitions above.
SCI sc800t3AlarmConfigIndex	1.3.6.1.4.1.498.19.1.7.1.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
sc800t3AlarmConfigTable	1.3.6.1.4.1.498.19.1.7.1		not-accessible	The sc800t3AlarmConfigTable contains entries that configure alarm reporting. The structure of the table is such that alarm configuration is supported on a unit and interface basis, and then on an alarm type basis within the interface. For simplicity sake alarms, be they unit or interface related, are represented in one table.
INT sc800t3AlarmCountThreshold	1.3.6.1.4.1.498.19.1.7.1.1.4	INTEGER	read-write	This function sets/reads the alarm threshold criteria. This threshold is used along with the the alarm window to determine the number of instances in a given time frame for an alarm to occur before the alarm is considered active.
INT sc800t3AlarmCountWindow	1.3.6.1.4.1.498.19.1.7.1.1.3	INTEGER	read-write	This variable sets/reads the alarm window. This window is used with the alarm threshold to determine how long the alarm should be active before reporting.
sc800t3Alarms	1.3.6.1.4.1.498.19.1.5
sc800t3BottomPowerSupplyFail	1.3.6.1.4.1.498.19.1.5.17
INT sc800t3BPSFAIL	1.3.6.1.4.1.498.19.1.8.1.1.9	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
sc800t3ChannelConfigEntry	1.3.6.1.4.1.498.19.1.2.1.1		not-accessible	The sc800t3 Channel Configuration table entry.
SCI sc800t3ChannelConfigIndex	1.3.6.1.4.1.498.19.1.2.1.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
sc800t3ChannelConfigTable	1.3.6.1.4.1.498.19.1.2.1		not-accessible	The GDC SC800T3 Channel Configuration table.
INT sc800t3ChannelDTEtest	1.3.6.1.4.1.498.19.1.2.1.1.3	INTEGER	read-write	DTE interface supporting loop A and loop B tests. See ANSI TIA/EIA-613-1993 specification for details on encoding of inter changes.
sc800t3CodeViolations	1.3.6.1.4.1.498.19.1.5.24
sc800t3ConfigChange	1.3.6.1.4.1.498.19.1.5.6
sc800t3Configuration	1.3.6.1.4.1.498.19.1.2
sc800t3CurrentDayFarEndEntry	1.3.6.1.4.1.498.19.1.6.6.1		not-accessible	An entry in the sc800t3CurrentDayFarEndTable.
SCI sc800t3CurrentDayFarEndIndex	1.3.6.1.4.1.498.19.1.6.6.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
OCT sc800t3CurrentDayFarEndStat	1.3.6.1.4.1.498.19.1.6.6.1.2	OCTET STRING	read-only	Returns a bitwise snapshot of the statistics. Octet 1 bit 7 - parity bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - 2^15 Errored Seconds (ES) bit 0 - 2^14 Octet 2 bit 7 - parity bit 6 - 2^13 Errored Seconds (ES) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 3 bit 7 - parity bit 6 - 2^6 Errored Seconds (ES) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 4 bit 7 - parity Severely Errored Seconds (SES) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 5 bit 7 - parity bit 6 - 2^6 Severely Errored Seconds (SES) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 6 bit 7 - parity Severely Errored Frame (SAS) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 7 bit 7 - parity bit 6 - 2^6 Severely Errored Frame (SAS) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 8 bit 7 - parity Unavailable Seconds (UAS) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 9 bit 7 - parity bit 6 - 2^6 Unavailable Seconds (UAS) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 10 bit 7 - parity Code Violations (CV) bit 6 - Invalid Data Flag bit 5 - 2^19 bit 4 - 2^18 bit 3 - 2^17 bit 2 - 2^16 bit 1 - 2^15 bit 0 - 2^14 Octet 11 bit 7 - parity bit 6 - 2^13 Code Violations (CV) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 12 bit 7 - parity bit 6 - 2^6 Code Violations (CV) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 13 bit 7 - parity FCCP-PFE Path Failure Events bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - 2^15 bit 0 - 2^14 Octet 14 bit 7 - parity bit 6 - 2^13 FCCP-PFE Path Failure Events bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 15 bit 7 - parity bit 6 - 2^6 FCCP-PFE Path Failure Events bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0
sc800t3CurrentDayFarEndTable	1.3.6.1.4.1.498.19.1.6.6		not-accessible	Gives totals for the current day of all the Far End statistics.
sc800t3CurrentDayNearEndEntry	1.3.6.1.4.1.498.19.1.6.4.1		not-accessible	An entry in the sc800t3 CurrentDayNearEndTable.
SCI sc800t3CurrentDayNearEndIndex	1.3.6.1.4.1.498.19.1.6.4.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
OCT sc800t3CurrentDayNearEndStat	1.3.6.1.4.1.498.19.1.6.4.1.2	OCTET STRING	read-only	Returns a bitwise snapshot of the statistics. Octet 1 bit 7 - parity bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - 2^15 Errored Seconds (ES) bit 0 - 2^14 Octet 2 bit 7 - parity bit 6 - 2^13 Errored Seconds (ES) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 3 bit 7 - parity bit 6 - 2^6 Errored Seconds (ES) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 4 bit 7 - parity Severely Errored Seconds (SES) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 5 bit 7 - parity bit 6 - 2^6 Severely Errored Seconds (SES) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 6 bit 7 - parity Severely Errored Frame (SAS) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 7 bit 7 - parity bit 6 - 2^6 Severely Errored Frame (SAS) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 8 bit 7 - parity Unavailable Seconds (UAS) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 9 bit 7 - parity bit 6 - 2^6 Unavailable Seconds (UAS) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 10 bit 7 - parity Code Violations (CV) bit 6 - Invalid Data Flag bit 5 - 2^19 bit 4 - 2^18 bit 3 - 2^17 bit 2 - 2^16 bit 1 - 2^15 bit 0 - 2^14 Octet 11 bit 7 - parity bit 6 - 2^13 Code Violations (CV) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 12 bit 7 - parity bit 6 - 2^6 Code Violations (CV) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 13 bit 7 - parity bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - 2^15 Errored Seconds Line (ESl) bit 0 - 2^14 Octet 14 bit 7 - parity bit 6 - 2^13 Errored Seconds Line (ESl) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 15 bit 7 - parity bit 6 - 2^6 Errored Seconds Line (ESl) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 16 bit 7 - parity bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - 2^15 FC-P Path Failure Events bit 0 - 2^14 Octet 17 bit 7 - parity bit 6 - 2^13 FC-P Path Failure Events bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 18 bit 7 - parity bit 6 - 2^6 FC-P Path Failure Events bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0
sc800t3CurrentDayNearEndTable	1.3.6.1.4.1.498.19.1.6.4		not-accessible	Gives totals for the current day of all the near end statistics.
sc800t3CurrentFarEndEntry	1.3.6.1.4.1.498.19.1.6.3.1		not-accessible	An entry in the sc800t3 CurrentFarEnd table.
SCI sc800t3CurrentFarEndIndex	1.3.6.1.4.1.498.19.1.6.3.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
OCT sc800t3CurrentFarEndStat	1.3.6.1.4.1.498.19.1.6.3.1.2	OCTET STRING	read-only	Returns a bitwise snapshot of the statistics. Octet 1 bit 7 - parity bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - 2^9 Errored Seconds (ES) bit 1 - 2^8 bit 0 - 2^7 Octet 2 bit 7 - parity bit 6 - 2^6 Errored Seconds (ES) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 3 bit 7 - parity Severely Errored Seconds (SES) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 4 bit 7 - parity Severely Errored Frames (SAS) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 5 bit 7 - parity Unavailable Seconds (UAS) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 6 bit 7 - parity Code Violations (CV) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - n/a bit 0 - n/a Octet 7 bit 7 - parity bit 6 - 2^13 Code Violations (CV) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 8 bit 7 - parity bit 6 - 2^6 Code Violations (CV) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 9 bit 7 - parity bit 6 - 2^6 Percent Complete bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0
sc800t3CurrentFarEndTable	1.3.6.1.4.1.498.19.1.6.3		not-accessible	Gives the statistic count for the current 15 minute interval.
sc800t3CurrentNearEndEntry	1.3.6.1.4.1.498.19.1.6.1.1		not-accessible	An entry in the sc800t3 CurrentNearEnd table.
SCI sc800t3CurrentNearEndIndex	1.3.6.1.4.1.498.19.1.6.1.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
OCT sc800t3CurrentNearEndStat	1.3.6.1.4.1.498.19.1.6.1.1.2	OCTET STRING	read-only	Returns a bitwise snapshot of the statistics. Octet 1 bit 7 - parity bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - 2^9 Errored Seconds (ES) bit 1 - 2^8 bit 0 - 2^7 Octet 2 bit 7 - parity bit 6 - 2^6 Errored Seconds (ES) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 3 bit 7 - parity Severely Errored Seconds (SES) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 4 bit 7 - parity Severely Errored Frames (SAS) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 5 bit 7 - parity Unavailable Seconds (UAS) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 6 bit 7 - parity Code Violations (CV) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - n/a bit 0 - n/a Octet 7 bit 7 - parity bit 6 - 2^13 Code Violations (CV) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 8 bit 7 - parity bit 6 - 2^6 Code Violations (CV) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 9 bit 7 - parity bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - 2^9 Errored Seconds Line (ESl) bit 1 - 2^8 bit 0 - 2^7 Octet 10 bit 7 - parity bit 6 - 2^6 Errored Seconds Line (ESl) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 11 bit 7 - parity bit 6 - 2^6 Percent Complete bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0
sc800t3CurrentNearEndTable	1.3.6.1.4.1.498.19.1.6.1		not-accessible	Gives the statistic count for the current 15 minute interval.
INT sc800t3DefaultInit	1.3.6.1.4.1.498.19.1.4.1.1.4	INTEGER	read-write	This is used to allow the NonVolatile Configuration to be set to a factory default state. When this value is set to factoryDefault, the unit will reset to the default configuration. The value of normal will be returned when the initialization is complete. The value normal can not be set by management.
sc800t3DiagEntry	1.3.6.1.4.1.498.19.1.3.1.1		not-accessible	The SNMPSC800T3 Diagnostics table entry.
SCI sc800t3DiagIndex	1.3.6.1.4.1.498.19.1.3.1.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
sc800t3Diagnostics	1.3.6.1.4.1.498.19.1.3
INT sc800t3DiagResetTestResults	1.3.6.1.4.1.498.19.1.3.1.1.6	INTEGER	read-write	This object will clear the results register while running any test except for Network Delay. Starting a new test will automatically zero out the register. A normal(1) will always be read. Management will set a resetTestResult(2) to reset the test results.
sc800t3DiagRxErrAlm	1.3.6.1.4.1.498.19.1.5.2
INT sc800t3DiagT3Test	1.3.6.1.4.1.498.19.1.3.1.1.4	INTEGER	read-write	A set of 2-11 starts the specified test and a set of t3NoTest(1) stops the current running test. A get returns the current active test.
sc800t3DiagTable	1.3.6.1.4.1.498.19.1.3.1		not-accessible	The SC800T3 Diagnostics table.
INT sc800t3DiagTestDuration	1.3.6.1.4.1.498.19.1.3.1.1.2	INTEGER	read-write	Selects the duration to run a diagnostic test.
OCT sc800t3DiagTestResults	1.3.6.1.4.1.498.19.1.3.1.1.5	OCTET STRING	read-only	Returns a the folowing bytes. Octet 1 bit 7 - F/U bit 6 - 1: Test complete bit 5 - 1: Test aborted bit 4 - F/U bit 3 - remote status 0: inactive 1: active bit 2 - 1: Bit errors over range bit 1 - Bit Errors bit 0 - Bit Errors Octet 2 bit 7 - F/U bit 6 - 2^13 bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 Bit Error Count bit 1 - 2^8 bit 0 - 2^7 Octet 3 bit 7 - F/U bit 6 - 2^6 bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0
INT sc800t3DownloadingMode	1.3.6.1.4.1.498.19.1.1.2.1.6	INTEGER	read-write	This object is used to configure the download mode: disableAll(1) Prevents any firmware downloading to SC800T3 enableAndWait(2) Allows downloading zipped code to be stored only! enableAndSwitch(3) Allows downloading and then unzips and begins executing the new code
INT sc800t3DTECLKLOS	1.3.6.1.4.1.498.19.1.8.1.1.10	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
INT sc800t3DTELoopTimeout	1.3.6.1.4.1.498.19.1.2.1.1.4	INTEGER	read-write	Enables/disables DTE loop time out.
INT sc800t3DTERDYLOS	1.3.6.1.4.1.498.19.1.8.1.1.11	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
sc800t3DTEReadyLoss	1.3.6.1.4.1.498.19.1.5.11
sc800t3DTETest	1.3.6.1.4.1.498.19.1.5.18
sc800t3DTETXCLKLoss	1.3.6.1.4.1.498.19.1.5.12
INT sc800t3EraseFlash	1.3.6.1.4.1.498.19.1.1.2.1.7	INTEGER	read-write	A set of this object to erase(2) will erase the application stored in flash. After setting this object, there should be a delay of at least 2 minutes before downloading the unit.
sc800t3ES	1.3.6.1.4.1.498.19.1.5.20
sc800t3ESline	1.3.6.1.4.1.498.19.1.5.25
sc800t3FarEndIntervalEntry	1.3.6.1.4.1.498.19.1.6.9.1		not-accessible	An entry in the Interval table.
SCI sc800t3FarEndIntervalIndex	1.3.6.1.4.1.498.19.1.6.9.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
INT sc800t3FarEndIntervalNumber	1.3.6.1.4.1.498.19.1.6.9.1.2	INTEGER	read-only	A number between 1 and 31, where 1 is the most recently completed minute interval and 31 is the least recently completed 15 minutes interval (assuming that all 31 intervals are valid).
OCT sc800t3FarEndIntervalStats	1.3.6.1.4.1.498.19.1.6.9.1.3	OCTET STRING	read-only	Returns a bitwise snapshot of the statistics. Octet 1 bit 7 - parity bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - 2^9 Errored Seconds (ES) bit 1 - 2^8 bit 0 - 2^7 Octet 2 bit 7 - parity bit 6 - 2^6 Errored Seconds (ES) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 3 bit 7 - parity Severely Errored Seconds (SES) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 4 bit 7 - parity Severely Errored Frames (SAS) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 5 bit 7 - parity Unavailable Seconds (UAS) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 6 bit 7 - parity Code Violations (CV) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - n/a bit 0 - n/a Octet 7 bit 7 - parity bit 6 - 2^13 Code Violations (CV) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 8 bit 7 - parity bit 6 - 2^6 Code Violations (CV) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 9 bit 7 - parity bit 6 - n/a Interval (1-31) bit 5 - n/a bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0
sc800t3FarEndIntervalTable	1.3.6.1.4.1.498.19.1.6.9		not-accessible	The sc800t3 Far End Interval table.
INT sc800t3FarEndResetStats	1.3.6.1.4.1.498.19.1.4.1.1.11	INTEGER	read-write	Supports the action of soft resetting the sc800t3ValidFarEndIntervals object. When this object is set to reset(2), then the unit will reset the sc800t3ValidFarEndIntervals object to zero. The value of norm(1) can not be set by management.
INT sc800t3FarEndStatLastInitial	1.3.6.1.4.1.498.19.1.4.1.1.13	INTEGER	read-only	Number of seconds from midnight Dec 31 1969 up until sc800t3ValidFarEndIntervals was last initialized to zero.
INT sc800t3ForcedDCE	1.3.6.1.4.1.498.19.1.2.1.1.2	INTEGER	read-write	Controls the operation of Data Communications Equipment (DCE) signal. The value followsDte(1) indicates that the channel's DCE follows Data Terminal Equipment (DTE) ready. The value forcedOn(2) indicates that DCE is forced on.
INT sc800t3InbandLoopback	1.3.6.1.4.1.498.19.1.2.2.1.9	INTEGER	read-write	Enables/disables the inband loop back.
INT sc800t3InsertBitError	1.3.6.1.4.1.498.19.1.3.1.1.3	INTEGER	read-write	A set of 2 will insert one bit error for test. Management may only write a 2. A 1 will always be read.
OCT sc800t3LedStatus	1.3.6.1.4.1.498.19.1.4.1.1.2	OCTET STRING	read-only	Returns a bitwise snapshot of the front panel LED state and front panel switches. Octet 1 bit 7 - f/u bit 6 - NTWK 0:LED off 1:LED on bit 5 - TM 0:LED off 1:LED on bit 4 - ALM 0:LED off 1:LED on bit 3 - f/u bit 2 - f/u bit 1 - f/u bit 0 - f/u Octet 2 bit 7 - f/u bit 6 - f/u bit 5 - f/u bit 4 - f/u bit 3 - f/u bit 2 - f/u bit 1 - f/u bit 0 - f/u Octet 3 bit 7 - f/u bit 6 - f/u bit 5 - f/u bit 4 - f/u bit 3 - f/u bit 2 - f/u bit 1 - f/u bit 0 - f/u
sc800t3LocalAlarmConfigEntry	1.3.6.1.4.1.498.19.1.8.1.1		not-accessible	An entry in the GDC Local Alarm Configuration table.
SCI sc800t3LocalAlarmConfigIndex	1.3.6.1.4.1.498.19.1.8.1.1.1	SCinstance	read-only	The index value which uniquely identifies the interface to which this entry is applicable.
sc800t3LocalAlarmConfigTable	1.3.6.1.4.1.498.19.1.8.1		not-accessible	The sc800t3LocalAlarmConfigTable contains entries that configure alarm reporting. The structure of the table is such that alarm configuration is supported on a unit and interface basis, and then on an alarm type basis within the interface. For simplicity sake alarms, be they unit or interface related, are represented in one table.
sc800t3LocalAlarms	1.3.6.1.4.1.498.19.1.8
INT sc800t3LOS	1.3.6.1.4.1.498.19.1.8.1.1.7	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
sc800t3LossOfSignal	1.3.6.1.4.1.498.19.1.5.8
sc800t3Maintenance	1.3.6.1.4.1.498.19.1.4
sc800t3MaintenanceEntry	1.3.6.1.4.1.498.19.1.4.1.1		not-accessible	An entry in the GDC maintenance Table
SCI sc800t3MaintenanceIndex	1.3.6.1.4.1.498.19.1.4.1.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
sc800t3MaintenanceTable	1.3.6.1.4.1.498.19.1.4.1		not-accessible	The table describes the maintenance functions for the sc800t3.
STR sc800t3MIBversion	1.3.6.1.4.1.498.19.1.1.1	DisplayString	read-only	Identifies the version of the MIB. The format of the version is x.yzT, where 'x' identifies the major revision number, 'y' identifies the minor revision number, 'z' identifies the typographical revision, and T identifies the test revision. Upon formal release, no designation for the test revision will be present. Acceptable values for the individual revision components are as follows: x: 1 - 9, y: 0 - 9, z: 0 - 9, T: A - Z
sc800t3NearEndIntervalEntry	1.3.6.1.4.1.498.19.1.6.7.1		not-accessible	An entry in the Interval table.
SCI sc800t3NearEndIntervalIndex	1.3.6.1.4.1.498.19.1.6.7.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
INT sc800t3NearEndIntervalNumber	1.3.6.1.4.1.498.19.1.6.7.1.2	INTEGER	read-only	A number between 1 and 31, where 1 is the most recently completed minute interval and 31 is the least recently completed 15 minutes interval (assuming that all 31 intervals are valid).
OCT sc800t3NearEndIntervalStats	1.3.6.1.4.1.498.19.1.6.7.1.3	OCTET STRING	read-only	Returns a bitwise snapshot of the statistics. Octet 1 bit 7 - parity bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - 2^9 Errored Seconds (ES) bit 1 - 2^8 bit 0 - 2^7 Octet 2 bit 7 - parity bit 6 - 2^6 Errored Seconds (ES) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 3 bit 7 - parity Severely Errored Seconds (SES) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 4 bit 7 - parity Severely Errored Frames (SAS) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 5 bit 7 - parity Unavailable Seconds (UAS) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 6 bit 7 - parity Code Violations (CV) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - n/a bit 0 - n/a Octet 7 bit 7 - parity bit 6 - 2^13 Code Violations (CV) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 8 bit 7 - parity bit 6 - 2^6 Code Violations (CV) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 9 bit 7 - parity bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - 2^9 Errored Seconds Line (ESl) bit 1 - 2^8 bit 0 - 2^7 Octet 10 bit 7 - parity bit 6 - 2^6 Errored Seconds Line (ESl) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 11 bit 7 - parity bit 6 - n/a Interval (1-31) bit 5 - n/a bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0
sc800t3NearEndIntervalTable	1.3.6.1.4.1.498.19.1.6.7		not-accessible	The sc800t3 Near End Interval table.
INT sc800t3NearEndResetStats	1.3.6.1.4.1.498.19.1.4.1.1.10	INTEGER	read-write	Supports the action of soft resetting the sc800t3ValidNearEndIntervals object. When this object is set to reset(2), then the unit will reset the sc800t3ValidNearEndIntervals object to zero. The value of norm(1) can not be set by management.
INT sc800t3NearEndStatLastInitial	1.3.6.1.4.1.498.19.1.4.1.1.12	INTEGER	read-only	Number of seconds from midnight Dec 31 1969 up until sc800t3ValidNearEndIntervals was last initialized to zero.
INT sc800t3NetworkAISLoopdown	1.3.6.1.4.1.498.19.1.2.2.1.4	INTEGER	read-write	The time in seconds when receiving a continuous AIS signal before a remotely initiated loopback is terminated. When this object has the value 4, then there is no time limit and the loop must be terminated by remotely issued in-band loopdown codes. When the object has a value between 5 and 60, then this is time in seconds of continuous AIS signal before the loopback is terminated.
sc800t3NetworkConfigEntry	1.3.6.1.4.1.498.19.1.2.2.1		not-accessible	The sc800t3 Network Configuration table entry.
SCI sc800t3NetworkConfigIndex	1.3.6.1.4.1.498.19.1.2.2.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
sc800t3NetworkConfigTable	1.3.6.1.4.1.498.19.1.2.2		not-accessible	The GDC SC800T3 Network Configuration table.
INT sc800t3NetworkFrameType	1.3.6.1.4.1.498.19.1.2.2.1.2	INTEGER	read-write	Is the framing type of the network interface. Setting the value of the object to m13(1) configures the network interface to M-13 framing. Setting the value of this object to cbitParity configures the network interface 20 C-bit parity framing
INT sc800t3NetworkIdleStatus	1.3.6.1.4.1.498.19.1.2.2.1.6	INTEGER	read-only	Returns a value of received(2) when the sc800t3 receives a DS3 idle from the network.
INT sc800t3NetworkLineType	1.3.6.1.4.1.498.19.1.2.2.1.5	INTEGER	read-write	The operating mode of the interface. Setting the value of this object to longCable(1) configures the interface as standard DS-3. Setting the value of this object to shortCable(2) configures the interface to operate as a standard cross-connect DSX-3.
INT sc800t3NetworkSesBERThreshold	1.3.6.1.4.1.498.19.1.2.2.1.8	INTEGER	read-write	When set to thresone(1), the SES BER threshold will be set to 1X10^-6 and when it is set to thresseven(2), it will be set to 7.5X10^-5.
INT sc800t3NetworkTransmitClockSource	1.3.6.1.4.1.498.19.1.2.2.1.3	INTEGER	read-write	The DSU transmit clock source option. This is the selection for the transmitter timing clock source.
INT sc800t3NetworkTransmitIdleStatus	1.3.6.1.4.1.498.19.1.2.2.1.7	INTEGER	read-write	When set to active(2), the sc800t3 will transmit a DS3 idle signal to the network.
sc800t3NoResponse	1.3.6.1.4.1.498.19.1.5.1
INT sc800t3OOF	1.3.6.1.4.1.498.19.1.8.1.1.2	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
sc800t3OutOfFrame	1.3.6.1.4.1.498.19.1.5.9
sc800t3Performance	1.3.6.1.4.1.498.19.1.6
sc800t3POSTFail	1.3.6.1.4.1.498.19.1.5.4
sc800t3PowerUpAlm	1.3.6.1.4.1.498.19.1.5.3
sc800t3PreviousDayFarEndEntry	1.3.6.1.4.1.498.19.1.6.5.1		not-accessible	An entry in the sc800t3PreviousDayFarEndTable.
SCI sc800t3PreviousDayFarEndIndex	1.3.6.1.4.1.498.19.1.6.5.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
OCT sc800t3PreviousDayFarEndStat	1.3.6.1.4.1.498.19.1.6.5.1.2	OCTET STRING	read-only	Returns a bitwise snapshot of the statistics. Octet 1 bit 7 - parity bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - 2^15 Errored Seconds (ES) bit 0 - 2^14 Octet 2 bit 7 - parity bit 6 - 2^13 Errored Seconds (ES) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 3 bit 7 - parity bit 6 - 2^6 Errored Seconds (ES) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 4 bit 7 - parity Severely Errored Seconds (SES) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 5 bit 7 - parity bit 6 - 2^6 Severely Errored Seconds (SES) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 6 bit 7 - parity Severely Errored Frame (SAS) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 7 bit 7 - parity bit 6 - 2^6 Severely Errored Frame (SAS) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 8 bit 7 - parity Unavailable Seconds (UAS) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 9 bit 7 - parity bit 6 - 2^6 Unavailable Seconds (UAS) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 10 bit 7 - parity Code Violations (CV) bit 6 - Invalid Data Flag bit 5 - 2^19 bit 4 - 2^18 bit 3 - 2^17 bit 2 - 2^16 bit 1 - 2^15 bit 0 - 2^14 Octet 11 bit 7 - parity bit 6 - 2^13 Code Violations (CV) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 12 bit 7 - parity bit 6 - 2^6 Code Violations (CV) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 13 bit 7 - parity FCCP-PFE Path Failure Events bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - 2^15 bit 0 - 2^14 Octet 14 bit 7 - parity bit 6 - 2^13 FCCP-PFE Path Failure Events bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 15 bit 7 - parity bit 6 - 2^6 FCCP-PFE Path Failure Events bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0
sc800t3PreviousDayFarEndTable	1.3.6.1.4.1.498.19.1.6.5		not-accessible	Gives totals for the previous day of all the Far End statistics.
sc800t3PreviousDayNearEndEntry	1.3.6.1.4.1.498.19.1.6.2.1		not-accessible	An entry in the sc800t3 PreviousDayNearEndTable.
SCI sc800t3PreviousDayNearEndIndex	1.3.6.1.4.1.498.19.1.6.2.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
OCT sc800t3PreviousDayNearEndStat	1.3.6.1.4.1.498.19.1.6.2.1.2	OCTET STRING	read-only	Returns a bitwise snapshot of the statistics. Octet 1 bit 7 - parity bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - 2^15 Errored Seconds (ES) bit 0 - 2^14 Octet 2 bit 7 - parity bit 6 - 2^13 Errored Seconds (ES) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 3 bit 7 - parity bit 6 - 2^6 Errored Seconds (ES) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 4 bit 7 - parity Severely Errored Seconds (SES) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 5 bit 7 - parity bit 6 - 2^6 Severely Errored Seconds (SES) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 6 bit 7 - parity Severely Errored Frame (SAS) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 7 bit 7 - parity bit 6 - 2^6 Severely Errored Frame (SAS) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 8 bit 7 - parity Unavailable Seconds (UAS) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 9 bit 7 - parity bit 6 - 2^6 Unavailable Seconds (UAS) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 10 bit 7 - parity Code Violations (CV) bit 6 - Invalid Data Flag bit 5 - 2^19 bit 4 - 2^18 bit 3 - 2^17 bit 2 - 2^16 bit 1 - 2^15 bit 0 - 2^14 Octet 11 bit 7 - parity bit 6 - 2^13 Code Violations (CV) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 12 bit 7 - parity bit 6 - 2^6 Code Violations (CV) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 13 bit 7 - parity bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - 2^15 Errored Seconds Line (ESl) bit 0 - 2^14 Octet 14 bit 7 - parity bit 6 - 2^13 Errored Seconds Line (ESl) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 15 bit 7 - parity bit 6 - 2^6 Errored Seconds Line (ESl) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 16 bit 7 - parity bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - 2^15 FC-P Path Failure Events bit 0 - 2^14 Octet 17 bit 7 - parity bit 6 - 2^13 FC-P Path Failure Events bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 18 bit 7 - parity bit 6 - 2^6 FC-P Path Failure Events bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0
sc800t3PreviousDayNearEndTable	1.3.6.1.4.1.498.19.1.6.2		not-accessible	Gives totals for the previous day of all the near end statistics.
sc800t3PreviousFarEndEntry	1.3.6.1.4.1.498.19.1.6.11.1		not-accessible	An entry in the sc800t3 PreviousFarEnd table.
SCI sc800t3PreviousFarEndIndex	1.3.6.1.4.1.498.19.1.6.11.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
OCT sc800t3PreviousFarEndStat	1.3.6.1.4.1.498.19.1.6.11.1.2	OCTET STRING	read-only	Returns a bitwise snapshot of the statistics. Octet 1 bit 7 - f/u bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - 2^9 Errored Seconds (ES) bit 1 - 2^8 bit 0 - 2^7 Octet 2 bit 7 - f/u bit 6 - 2^6 Errored Seconds (ES) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 3 bit 7 - f/u Severely Errored Seconds (SES) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 4 bit 7 - f/u Severely Errored Frames (SAS) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 5 bit 7 - f/u Unavailable Seconds (UAS) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 6 bit 7 - f/u Code Violations (CV) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - n/a bit 0 - n/a Octet 7 bit 7 - f/u bit 6 - 2^13 Code Violations (CV) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 8 bit 7 - f/u bit 6 - 2^6 Code Violations (CV) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0
sc800t3PreviousFarEndTable	1.3.6.1.4.1.498.19.1.6.11		not-accessible	Gives the statistic count for the previous 15 minute interval.
sc800t3PreviousNearEndEntry	1.3.6.1.4.1.498.19.1.6.10.1		not-accessible	An entry in the sc800t3 PreviousNearEnd table.
SCI sc800t3PreviousNearEndIndex	1.3.6.1.4.1.498.19.1.6.10.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
OCT sc800t3PreviousNearEndStat	1.3.6.1.4.1.498.19.1.6.10.1.2	OCTET STRING	read-only	Returns a bitwise snapshot of the statistics. Octet 1 bit 7 - f/u bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - 2^9 Errored Seconds (ES) bit 1 - 2^8 bit 0 - 2^7 Octet 2 bit 7 - f/u bit 6 - 2^6 Errored Seconds (ES) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 3 bit 7 - f/u Severely Errored Seconds (SES) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 4 bit 7 - f/u Severely Errored Frames (SAS) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 5 bit 7 - f/u Unavailable Seconds (UAS) bit 6 - Invalid Data Flag bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 6 bit 7 - f/u Code Violations (CV) bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - n/a bit 1 - n/a bit 0 - n/a Octet 7 bit 7 - f/u bit 6 - 2^13 Code Violations (CV) bit 5 - 2^12 bit 4 - 2^11 bit 3 - 2^10 bit 2 - 2^9 bit 1 - 2^8 bit 0 - 2^7 Octet 8 bit 7 - f/u bit 6 - 2^6 Code Violations (CV) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 9 bit 7 - fu bit 6 - Invalid Data Flag bit 5 - n/a bit 4 - n/a bit 3 - n/a bit 2 - 2^9 Errored Seconds Line (ESl) bit 1 - 2^8 bit 0 - 2^7 Octet 10 bit 7 - f/u bit 6 - 2^6 Errored Seconds Line (ESl) bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0 Octet 11 bit 7 - f/u bit 6 - 2^6 Percent Complete bit 5 - 2^5 bit 4 - 2^4 bit 3 - 2^3 bit 2 - 2^2 bit 1 - 2^1 bit 0 - 2^0
sc800t3PreviousNearEndTable	1.3.6.1.4.1.498.19.1.6.10		not-accessible	Gives the statistic count for the previous 15 minute interval.
sc800t3RAI	1.3.6.1.4.1.498.19.1.5.19
INT sc800t3RAILOCAL	1.3.6.1.4.1.498.19.1.8.1.1.12	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
sc800t3RemoteNotResponding	1.3.6.1.4.1.498.19.1.5.15
INT sc800t3RXDLOS	1.3.6.1.4.1.498.19.1.8.1.1.6	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
sc800t3RXDNoTrans	1.3.6.1.4.1.498.19.1.5.13
sc800t3SAS	1.3.6.1.4.1.498.19.1.5.22
sc800t3SES	1.3.6.1.4.1.498.19.1.5.21
INT sc800t3ShelfType	1.3.6.1.4.1.498.19.1.4.1.1.7	INTEGER	read-only	Type of shelf the sc800t3 is located in.
INT sc800t3SoftReset	1.3.6.1.4.1.498.19.1.4.1.1.3	INTEGER	read-write	Supports the action of soft resetting the unit. When this object is set to reset(1), then the unit performs a soft reset. The value norm will be returned when the reset is complete. The value of norm can not be set by management.
STR sc800t3StandbyFirmwareRev	1.3.6.1.4.1.498.19.1.1.2.1.3	DisplayString	read-only	The version number of the firmware stored (in a compressed format) but not currently executing. MM: Major Revision (0-99) NN: Minor Revision (0-99) BB: Bug Fix Revision (0-99)
INT sc800t3StoredFirmwareStatus	1.3.6.1.4.1.498.19.1.1.2.1.4	INTEGER	read-only	This object represents the state of the Non-Active or Stored firmware: statBlank(1) Factory Default statDownLoading(2) In process of downloading firmware statOK(3) Zipped version checksum succesful (OK to switch) (can set sc800t3SwitchActive to switchActive(2)) statCheckSumBad(4) Failed checksum after download statUnZipping(5) In process of uncompressing into active area statBadUnZip(6) Failed last uncompress statDownloadAborted(7) Download aborted by user
INT sc800t3SwitchActiveFirmware	1.3.6.1.4.1.498.19.1.1.2.1.5	INTEGER	read-write	This object is used to switch the active executing firmware from the version in sc800t3ActiveRev to the version in sc800t3StoredRev. When a switchActive(2) is set (write only) the element will: 1) reboot 2) uncompress stored code into active area 3) perform checksum on active area 4) Set sc800t3StoredStatus object to indicate results 5) If succesfull: update sc800t3ActiveFirmwareRev and sc800t3StoredFirmwareRev and begin executing If failed: replace active area with previous revision The switchNorm(1) enumeration will always be read. Setting switchActive(2) when the sc800t3StoredStatus is not statOK(3) will result in an error.
INT sc800t3TestAllLeds	1.3.6.1.4.1.498.19.1.4.1.1.9	INTEGER	read-write	This variable is used to test the front panel leds and individual segments of the display. A one (1) will turn all leds and display segments on. They will remain on until a two (2) is set or the card is rebooted
INT sc800t3THRESHCV	1.3.6.1.4.1.498.19.1.8.1.1.18	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
INT sc800t3THRESHES	1.3.6.1.4.1.498.19.1.8.1.1.14	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
INT sc800t3THRESHESL	1.3.6.1.4.1.498.19.1.8.1.1.13	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
INT sc800t3THRESHSAS	1.3.6.1.4.1.498.19.1.8.1.1.16	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
INT sc800t3THRESHSES	1.3.6.1.4.1.498.19.1.8.1.1.15	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
INT sc800t3THRESHUAS	1.3.6.1.4.1.498.19.1.8.1.1.17	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
sc800t3TimingLoss	1.3.6.1.4.1.498.19.1.5.7
INT sc800t3TIMLOS	1.3.6.1.4.1.498.19.1.8.1.1.4	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
sc800t3TopPowerSupplyFail	1.3.6.1.4.1.498.19.1.5.16
INT sc800t3TPSFAIL	1.3.6.1.4.1.498.19.1.8.1.1.8	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
INT sc800t3TwinPackPowerSupply	1.3.6.1.4.1.498.19.1.4.1.1.8	INTEGER	read-only	Power supplies currently installed in Twin Pack. When the sc800t3 is located in a Spectracomm shelf none(1) will always be returned.
INT sc800t3TXDLOS	1.3.6.1.4.1.498.19.1.8.1.1.5	INTEGER	read-write	Disables or enables the alarm on the Major buss or Minor buss.
sc800t3TXDNoTrans	1.3.6.1.4.1.498.19.1.5.14
sc800t3UAS	1.3.6.1.4.1.498.19.1.5.23
sc800t3UnsolicitedTest	1.3.6.1.4.1.498.19.1.5.5
INT sc800t3ValidFarEndIntervals	1.3.6.1.4.1.498.19.1.4.1.1.6	INTEGER	read-only	The number of previous far end intervals for which valid data was collected. The value will be 31 unless the interface was brought on-line within the last 7.75 hours, in which case the value will be the number of complete 15 minute intervals since the interface has been online.
INT sc800t3ValidNearEndIntervals	1.3.6.1.4.1.498.19.1.4.1.1.5	INTEGER	read-only	The number of previous near end intervals for which valid data was collected. The value will be 31 unless the interface was brought on-line within the last 7.75 hours, in which case the value will be the number of complete 15 minute intervals since the interface has been online.
sc800t3Version	1.3.6.1.4.1.498.19.1.1
sc800t3VersionEntry	1.3.6.1.4.1.498.19.1.1.2.1		not-accessible	An entry in the GDC SC800T3 Version Table.
SCI sc800t3VersionIndex	1.3.6.1.4.1.498.19.1.1.2.1.1	SCinstance	read-only	Integer value which uniquely identifies the SC800T3 to which this entry is applicable. SCinstance is defined to be SLDi where: S (byte value) - physical shelf slot location (01-32) L (byte value) - line number (01) D (byte value) - drop number (00) i (byte value) - interface number (00)
sc800t3VersionTable	1.3.6.1.4.1.498.19.1.1.2		not-accessible

RFC description

Monitors T3 line statistics, alarms, and performance metrics for GDC SC800 T3 transmission equipment.

Start monitoring General DataComm (GDC) SC800 T3 channel-service unit with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download GDC-SC800T3-MIB

What Is GDC-SC800T3-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description