GDCDATX-MIB

All MIBs › GDCDATX-MIB

Category: Domain: WAN/TDM, Vendor: GDC

Description: General DataComm DATX MIB for data transmission equipment configuration and performance monitoring.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is GDCDATX-MIB?

GDCDATX-MIB is a General DataComm proprietary MIB for the DATX line of data transmission/multiplexer equipment used in legacy WAN and telecom access networks. It exposes maintenance and configuration data for the device, including a maintenance table with firmware revision, default initialization settings, front panel and LED status, and a transmission configuration table covering serial line parameters such as baud rate. Its monitoring value centers on hardware and firmware status: administrators can check datxFirmwareRev to confirm the running software version, datxLedStatus and datxFrontPanel to gauge device-reported hardware health/alarm indications, and datxBaudRate/transmission config entries to verify the data line is configured and operating as expected. It is a self-contained vendor MIB with no apparent dependency on other standard MIBs. It was typically deployed on General DataComm DATX multiplexers/DSU-CSU equipment used at WAN circuit endpoints in legacy telecom and enterprise data networks. Engineers can download the GDCDATX-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in GDCDATX-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

General DataComm DATX WAN multiplexer/data transmission unit

Monitoring Examples

An administrator would poll datxMaintTable entries indexed by datxMaintIndex to read datxFirmwareRev and datxLedStatus, confirming the unit is running expected firmware and reporting a healthy front-panel LED state. Checking datxTransConfigTable entries for datxBaudRate against the expected line speed would reveal a serial configuration mismatch causing a WAN circuit outage. An unexpected datxLedStatus value combined with a stale datxFirmwareRev could reveal a unit that failed to complete a firmware upgrade.

What Can Be Monitored

firmware revision
front panel/LED status
transmission line baud rate configuration
maintenance table entries
default initialization state

Imported Objects

From GDCMACRO-MIB

SCinstance

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

TimeTicks
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
gdc	1.3.6.1.4.1.498
datx	1.3.6.1.4.1.498.7
datxSystem	1.3.6.1.4.1.498.7.1
datxVersion	1.3.6.1.4.1.498.7.1.1
STR datxMIBversion	1.3.6.1.4.1.498.7.1.1.1	DisplayString	read-only	Identifies the version of the MIB. The format of the version is x.yzT, where 'x' identifies the major revision number, 'y' identifies the minor revision number, 'z' identifies the typographical revision, and T identifies the test revision. Acceptable values for the individual revision components are as follows: x: 1 - 9 y: 0 - 9 z: 0 - 9 T: A - Z Upon formal release, no designation for the test revision will be present.
datxMaintenance	1.3.6.1.4.1.498.7.1.2
datxMaintTable	1.3.6.1.4.1.498.7.1.2.1		not-accessible	This table describes the maintenance objects for the unit
datxMaintEntry	1.3.6.1.4.1.498.7.1.2.1.1		not-accessible	An entry in the GDC Datx Maintenance Table.
SCI datxMaintIndex	1.3.6.1.4.1.498.7.1.2.1.1.1	SCinstance	read-only	The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a slot, line, drop, and sub-identifier.
STR datxFirmwareRev	1.3.6.1.4.1.498.7.1.2.1.1.2	DisplayString	read-only	The version number of the firmware, to allow products to know which revision is installed. The released version number is sequenced from --, A-, ... AA, ... ZZ. Test versions are numerical from 01 to 99.
INT datxDefaultInit	1.3.6.1.4.1.498.7.1.2.1.1.3	INTEGER	read-write	This is used to allow the NonVolatile Configuration to be set to a factory default state. When this value is set to factoryDefault(2) the unit will perform a reset to make the default configuration take affect. The value of normal(1) will be returned when the initialization is complete.
INT datxFrontPanel	1.3.6.1.4.1.498.7.1.2.1.1.4	INTEGER	read-write	This variable is used to indicate whether the front panel switches are operational or not. 'inhibit' refers to when the front panel switches are not operational. 'enable' refers to when the front panel switches are operational.
OCT datxLedStatus	1.3.6.1.4.1.498.7.1.2.1.1.5	OCTET STRING	read-only	Returns a bitwise snapshot of the front panel LED state. Octet 1 bit 7 - not used bit 6 - ON bit 5 - RD bit 4 - SD bit 3 - CS bit 2 - CO bit 1 - ALM bit 0 - TM Octet 2 bit 7 - not used bit 6 - ST bit 5 - LL bit 4 - RDL bit 3 - future use bit 2 - future use bit 1 - future use bit 0 - future use
datxConfiguration	1.3.6.1.4.1.498.7.1.3
datxTransConfigTable	1.3.6.1.4.1.498.7.1.3.1		not-accessible	This table describes the DATX transmission mode configuration options
datxTransConfigEntry	1.3.6.1.4.1.498.7.1.3.1.1		not-accessible	An entry in the transmission configuration table
SCI datxTransConfigIndex	1.3.6.1.4.1.498.7.1.3.1.1.1	SCinstance	read-only	The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a slot, line, drop, and sub-identifier.
INT datxBaudRate	1.3.6.1.4.1.498.7.1.3.1.1.2	INTEGER	read-write	SYNC/ASYNC Mode operation and Baud Rates
INT datxSyncTxClockSource	1.3.6.1.4.1.498.7.1.3.1.1.3	INTEGER	read-write	Synchronous Tx Clock Configuration
INT datxEiaSyncClock	1.3.6.1.4.1.498.7.1.3.1.1.4	INTEGER	read-write	Control for the EIA sync clock
datxEiaConfigTable	1.3.6.1.4.1.498.7.1.3.2		not-accessible	DATX EIA line configuration options
datxEiaConfigEntry	1.3.6.1.4.1.498.7.1.3.2.1		not-accessible	An entry in the EIA config table
SCI datxEIAIndex	1.3.6.1.4.1.498.7.1.3.2.1.1	SCinstance	read-only	The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a slot, line, drop, and sub-identifier.
INT datxCarrierControl	1.3.6.1.4.1.498.7.1.3.2.1.2	INTEGER	read-write
INT datxRtsMode	1.3.6.1.4.1.498.7.1.3.2.1.3	INTEGER	read-write	RTS mode selection
INT datxRtsCtsDelay	1.3.6.1.4.1.498.7.1.3.2.1.4	INTEGER	read-write	RTS/CTS Delay time
INT datxEiaRdlControl	1.3.6.1.4.1.498.7.1.3.2.1.5	INTEGER	read-write	EIA RDL control selection
INT datxDsrInAl	1.3.6.1.4.1.498.7.1.3.2.1.6	INTEGER	read-write	Selection for providing DSR will in AL mode
INT datxEiaAlControl	1.3.6.1.4.1.498.7.1.3.2.1.7	INTEGER	read-write	EIA AL control
datxMiscConfigTable	1.3.6.1.4.1.498.7.1.3.3		not-accessible	DATX misc configuration options
datxMiscConfigEntry	1.3.6.1.4.1.498.7.1.3.3.1		not-accessible	An entry in the misc config table
SCI datxMiscIndex	1.3.6.1.4.1.498.7.1.3.3.1.1	SCinstance	read-only	The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a slot, line, drop, and sub-identifier.
INT datxSystemStatusOption	1.3.6.1.4.1.498.7.1.3.3.1.2	INTEGER	read-write	Causes to drop CTS in master mode when remote drops line
INT datxDualSignalingTimer	1.3.6.1.4.1.498.7.1.3.3.1.3	INTEGER	read-write
INT datxRegenCharLength	1.3.6.1.4.1.498.7.1.3.3.1.4	INTEGER	read-write	Synchronous Tx Clock Configuration
INT datxRegenMode	1.3.6.1.4.1.498.7.1.3.3.1.5	INTEGER	read-write	Regen Mode Control
INT datxAsyncRate	1.3.6.1.4.1.498.7.1.3.3.1.6	INTEGER	read-write
datxDiagnostics	1.3.6.1.4.1.498.7.1.4
datxDiagnosticsTable	1.3.6.1.4.1.498.7.1.4.1		not-accessible	DATX diagnostics options
datxDiagEntry	1.3.6.1.4.1.498.7.1.4.1.1		not-accessible	List of Diagnostic Tests and Status Indicators related to the tests
SCI datxDiagnosticsIndex	1.3.6.1.4.1.498.7.1.4.1.1.1	SCinstance	read-only	The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a slot, line, drop, and sub-identifier.
INT datxDiagTest	1.3.6.1.4.1.498.7.1.4.1.1.2	INTEGER	read-write	Perform diagnostic tests on a unit noTest - stops any test in progress selfTest - sends a selftest pattern analoop - puts the unit into analog loopback analoopSelfTest - puts the unit into analog loopback with a self test pattern remoteDL - performs a remote digital loopback remoteDLselfTest - performs a remote digital loopback with a self test pattern
INT datxTestError	1.3.6.1.4.1.498.7.1.4.1.1.3	INTEGER	read-only	Test result indicator, shows the results of the last test
TIK datxTestDuration	1.3.6.1.4.1.498.7.1.4.1.1.4	TimeTicks	read-only	Indicates the time duration of any test in progress
datxStatus	1.3.6.1.4.1.498.7.1.5
datxStatusTable	1.3.6.1.4.1.498.7.1.5.1		not-accessible	DATX Status indicators
datxStatusEntry	1.3.6.1.4.1.498.7.1.5.1.1		not-accessible	Entry in the status indicator table
SCI datxStatusIndex	1.3.6.1.4.1.498.7.1.5.1.1.1	SCinstance	read-only	The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a slot, line, drop, and sub-identifier.
INT datxDTRstatus	1.3.6.1.4.1.498.7.1.5.1.1.2	INTEGER	read-only	DTR EIA status indicator
INT datxRDLstatus	1.3.6.1.4.1.498.7.1.5.1.1.3	INTEGER	read-only	RDL EIA control status indicator
INT datxCOstatus	1.3.6.1.4.1.498.7.1.5.1.1.4	INTEGER	read-only	CO EIA status indicator
INT datxCTSstatus	1.3.6.1.4.1.498.7.1.5.1.1.5	INTEGER	read-only	CTS EIA indicator
INT datxRTSstatus	1.3.6.1.4.1.498.7.1.5.1.1.6	INTEGER	read-only	RTS EIA indicator
INT datxTMstatus	1.3.6.1.4.1.498.7.1.5.1.1.7	INTEGER	read-only	Test mode EIA indicator
INT datxALstatus	1.3.6.1.4.1.498.7.1.5.1.1.8	INTEGER	read-only	Analoop EIA status indicator
INT datxDSRstatus	1.3.6.1.4.1.498.7.1.5.1.1.9	INTEGER	read-only	DSR EIA status indicator
INT datxRXclock	1.3.6.1.4.1.498.7.1.5.1.1.10	INTEGER	read-only	RxClk activity indicator
INT datxTXclock	1.3.6.1.4.1.498.7.1.5.1.1.11	INTEGER	read-only	TxClk activity indicator
INT datxEXTclock	1.3.6.1.4.1.498.7.1.5.1.1.12	INTEGER	read-only	External clock activity indicator
OCT datxAlarmStatus	1.3.6.1.4.1.498.7.1.5.1.1.13	OCTET STRING	read-only	The current alarms of the unit without the alarm masks.
dtx2011	1.3.6.1.4.1.498.7.2
dtx2011AlarmData	1.3.6.1.4.1.498.7.2.1
dtx2011NoResponseAlm	1.3.6.1.4.1.498.7.2.1.1
dtx2011DiagRxErrAlm	1.3.6.1.4.1.498.7.2.1.2
dtx2011PowerUpAlm	1.3.6.1.4.1.498.7.2.1.3
dtx2011DCDLossAlm	1.3.6.1.4.1.498.7.2.1.4
dtx2011NoExtClockAlm	1.3.6.1.4.1.498.7.2.1.5

RFC description

GDC DATX data transmission product management with DS1 interface status and configuration monitoring.

Start monitoring General DataComm (GDC) DATX WAN multiplexer/data transmission unit with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download GDCDATX-MIB

What Is GDCDATX-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description