CISCO-SCTP-MIB

All MIBs › CISCO-SCTP-MIB

Organization: Cisco Systems, Inc.

Last Updated: 2005-12-21

Category: Cisco Devices, IP and Core Protocols

Description: Manages and monitors SCTP associations, endpoints, and protocol statistics on Cisco devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-SCTP-MIB?

CISCO-SCTP-MIB is a Cisco MIB module for managing and monitoring the Stream Control Transmission Protocol (SCTP) implementation on Cisco devices, per its module description. SCTP is a transport-layer protocol used heavily in telecom signaling (e.g., SIGTRAN, Diameter, SS7-over-IP) that supports multi-homed, multi-streamed associations. Its monitoring value is in software/protocol status and performance: tracking SCTP associations and endpoints, their states, and protocol-level statistics such as packet/error counts, which helps detect failed associations, path failures, or abnormal retransmission rates in signaling transport. It is closely tied to the IETF SCTP standard (RFC 4960) and is typically used alongside standard transport/interface MIBs when troubleshooting signaling links. It is deployed on Cisco routers/media gateways acting as SCTP endpoints in telecom signaling networks, and engineers can obtain a CISCO-SCTP-MIB download to load it directly into their MIB browser for reference.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-SCTP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco router/media gateway with SCTP signaling support

Monitoring Examples

No sample objects were provided in the source for this module, so specific table or object names cannot be verified here. Based on the module description, an administrator would be expected to poll SCTP association and endpoint tables to confirm association state (established vs. failed) and review per-association statistics such as retransmissions or path failures; a rise in retransmissions or an association dropping to a non-established state would indicate a signaling transport problem.

What Can Be Monitored

SCTP association state
SCTP endpoint status
SCTP protocol statistics (packets/errors)

Imported Objects

From CISCO-SMI

ciscoExperiment

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION

How to Use in IPNetwork Monitor

Example using ceSctpCurrEstab OID:

Select a Cisco router/media gateway with SCTP signaling support as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type ceSctpCurrEstab into the Find box to locate it in the OID tree, then select it and click OK. The number of SCTP associations for which the current state is either ESTABLISHED, SHUTDOWN-RECEIVED or SHUTDOWN-PENDING. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
C32 ceSctpAborted	1.3.6.1.4.1.9.10.74.1.1.6	Counter32	read-only	The number of times that SCTP associations have made a direct transition to the CLOSED state from any state using the primitive 'ABORT': AnyState --Abort--> CLOSED. Ungraceful termination of the association.
C32 ceSctpActiveEstab	1.3.6.1.4.1.9.10.74.1.1.4	Counter32	read-only	The number of times that SCTP associations have made a direct transition to the ESTABLISH state from the COOKIE-ECHOED state: COOKIE-ECHOED -> ESTABLISHED. The upper layer has initiated the association attempt.
C64 ceSctpAssocBytesRec	1.3.6.1.4.1.9.10.74.1.2.1.1.38	Counter64	read-only	Number of bytes received by this association.
C64 ceSctpAssocBytesSent	1.3.6.1.4.1.9.10.74.1.2.1.1.37	Counter64	read-only	Number of bytes sent by this association.
C64 ceSctpAssocChecksumErrorCounter	1.3.6.1.4.1.9.10.74.1.2.1.1.36	Counter64	read-only	Number of SCTP packets received from the peers with an invalid checksum.
C64 ceSctpAssocChunksDiscarded	1.3.6.1.4.1.9.10.74.1.2.1.1.39	Counter64	read-only	Total number of Chucks discarded by this association.
C64 ceSctpAssocChunksRec	1.3.6.1.4.1.9.10.74.1.2.1.1.40	Counter64	read-only	Total number of Chucks received by this association.
C64 ceSctpAssocChunksRecControl	1.3.6.1.4.1.9.10.74.1.2.1.1.41	Counter64	read-only	Number of control Chucks received by this association.
C64 ceSctpAssocChunksRecOrdered	1.3.6.1.4.1.9.10.74.1.2.1.1.42	Counter64	read-only	Number of Chucks received by this association where order is required.
C64 ceSctpAssocChunksRecOutOrder	1.3.6.1.4.1.9.10.74.1.2.1.1.44	Counter64	read-only	Number of Chucks received out of order by this association.
C64 ceSctpAssocChunksRecUnOrdered	1.3.6.1.4.1.9.10.74.1.2.1.1.43	Counter64	read-only	Number of Chucks received by this association where order is not required.
C64 ceSctpAssocChunksReTrans	1.3.6.1.4.1.9.10.74.1.2.1.1.45	Counter64	read-only	Total number of Chucks retransmitted by this association.
C64 ceSctpAssocChunksSent	1.3.6.1.4.1.9.10.74.1.2.1.1.46	Counter64	read-only	Total number of Chucks sent by this association.
C64 ceSctpAssocChunksSentControl	1.3.6.1.4.1.9.10.74.1.2.1.1.47	Counter64	read-only	Number of control Chucks sent by this association.
C64 ceSctpAssocChunksSentOrdered	1.3.6.1.4.1.9.10.74.1.2.1.1.48	Counter64	read-only	Number of Chucks sent by this association where order is required.
C64 ceSctpAssocChunksSentUnOrdered	1.3.6.1.4.1.9.10.74.1.2.1.1.49	Counter64	read-only	Number of Chucks sent by this association where order is not required.
U32 ceSctpAssocCongestionAbate1	1.3.6.1.4.1.9.10.74.1.2.1.1.18	Unsigned32	read-only	Threshold used to abate congestion level 1.
U32 ceSctpAssocCongestionAbate2	1.3.6.1.4.1.9.10.74.1.2.1.1.19	Unsigned32	read-only	Threshold used to abate congestion level 2.
U32 ceSctpAssocCongestionAbate3	1.3.6.1.4.1.9.10.74.1.2.1.1.20	Unsigned32	read-only	Threshold used to abate congestion level 3.
U32 ceSctpAssocCongestionLevels	1.3.6.1.4.1.9.10.74.1.2.1.1.16	Unsigned32	read-only	Number of supported congestion Levels.
U32 ceSctpAssocCongestionLevelsCur	1.3.6.1.4.1.9.10.74.1.2.1.1.17	Unsigned32	read-only	Current congestion level.
U32 ceSctpAssocCongestionOnset1	1.3.6.1.4.1.9.10.74.1.2.1.1.21	Unsigned32	read-only	Threshold used to mark onset of congestion level 1.
U32 ceSctpAssocCongestionOnset2	1.3.6.1.4.1.9.10.74.1.2.1.1.22	Unsigned32	read-only	Threshold used to mark onset of congestion level 2.
U32 ceSctpAssocCongestionOnset3	1.3.6.1.4.1.9.10.74.1.2.1.1.23	Unsigned32	read-only	Threshold used to mark onset of congestion level 3.
C64 ceSctpAssocDatagramsRec	1.3.6.1.4.1.9.10.74.1.2.1.1.50	Counter64	read-only	Number of packets received by this association.
C64 ceSctpAssocDatagramsSent	1.3.6.1.4.1.9.10.74.1.2.1.1.51	Counter64	read-only	Number of packets sent by this association.
ceSctpAssocEntry	1.3.6.1.4.1.9.10.74.1.2.1.1		not-accessible	General common variables and statistics for the whole association.
U32 ceSctpAssocId	1.3.6.1.4.1.9.10.74.1.2.1.1.1	Unsigned32	not-accessible	Association Identification. Value identifying the association (typically the Initiate Verification Tag).
U32 ceSctpAssocInitialT1	1.3.6.1.4.1.9.10.74.1.2.1.1.9	Unsigned32	read-only	Initial value for the Start-up T1 timer.
U32 ceSctpAssocInitialT2	1.3.6.1.4.1.9.10.74.1.2.1.1.10	Unsigned32	read-only	Initial value for the Shutdown T2-shutdown timer.
U32 ceSctpAssocInStreams	1.3.6.1.4.1.9.10.74.1.2.1.1.24	Unsigned32	read-only	Inbound Streams according to the negotiation at association start up. This parameter has to be read-only by the manager.
ceSctpAssocLocalAddressEntry	1.3.6.1.4.1.9.10.74.1.2.2.1		not-accessible	Local information about the available addresses.
IP ceSctpAssocLocalAddressIP	1.3.6.1.4.1.9.10.74.1.2.2.1.2	InetAddress	not-accessible	The value of a local IP address available for this association. An InetAddress value is always interpreted within the context of an InetAddressType value. If SCTP are using DNS names, the mapping to IP address-es will be done at reception of INIT or INIT_ACK messages.
IPt ceSctpAssocLocalAddressIPType	1.3.6.1.4.1.9.10.74.1.2.2.1.1	InetAddressType	not-accessible	Internet type of local IP address used for this association. - unknown (0) An unknown address type. This value MUST be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address different from IPv4 or IPv6. This value is used in this MIB for error conditions. - ipv4 (1): An IPv4 address as defined by the InetAddressIPv4 textual convention [RFC2851]. - ipv6 (2): An IPv6 address as defined by the InetAddressIPv6 textual convention [RFC2851].
ROW ceSctpAssocLocalAddressRowStatus	1.3.6.1.4.1.9.10.74.1.2.2.1.3	RowStatus	read-only	An object that allows entries in this table to be created and deleted using the RowStatus convention. A row in this table will be created per local IP address defined for this association. The creation takes part when a new row in the sctpAssocTable is created or when a new IP address is added in the local interface (if this function is enabled by the SCTP layer). A row in this table will be deleted per local IP address reserved for the association when the corresponding row in sctpAssocTable is deleted or when an IP address is removed from the local interface (if this function is enabled by the SCTP layer).
ceSctpAssocLocalAddressTable	1.3.6.1.4.1.9.10.74.1.2.2		not-accessible	Expanded table of ceSctpAssocTable based on the AssocId index. It shows several interesting data for each local address which takes part in this association.
U32 ceSctpAssocLocalSCTPPort	1.3.6.1.4.1.9.10.74.1.2.1.1.12	Unsigned32	read-only	Local SCTP port number used for this association.
U32 ceSctpAssocLocRecWnd	1.3.6.1.4.1.9.10.74.1.2.1.1.28	Unsigned32	read-only	The current local receive window size for this association.
U32 ceSctpAssocLocRecWndLowMark	1.3.6.1.4.1.9.10.74.1.2.1.1.29	Unsigned32	read-only	Low water mark for Local Receive Window Size.
C64 ceSctpAssocLocRecWndZeroCnt	1.3.6.1.4.1.9.10.74.1.2.1.1.30	Counter64	read-only	Number of times the Local Receive window reached zero bytes.
U32 ceSctpAssocMaxInitRetr	1.3.6.1.4.1.9.10.74.1.2.1.1.8	Unsigned32	read-only	The maximum number of retransmissions at the start-up phase (INIT and COOKIE ECHO chunks). Recommended value: 8 attempts.
U32 ceSctpAssocMaxRetr	1.3.6.1.4.1.9.10.74.1.2.1.1.26	Unsigned32	read-only	The maximum number of data retransmissions. This value is specific for each association and the upper layer can be able to change it calling the appropriate primitives. This value has to be smaller than the addition of all the maximum number for all the paths (sctpAssocRemAddressMaxPathRetran). Recommended value: 10 attempts.
U32 ceSctpAssocMTU	1.3.6.1.4.1.9.10.74.1.2.1.1.27	Unsigned32	read-only	The Maximum Transmission Size to be used by this association. The size will the smallest MTU size supported by any of the IP Addresses used by the association.
U32 ceSctpAssocOutStreams	1.3.6.1.4.1.9.10.74.1.2.1.1.25	Unsigned32	read-only	Outbound Streams according to the negotiation at association start up. This parameter has to be read-only by the manager.
ceSctpAssocRemAddressEntry	1.3.6.1.4.1.9.10.74.1.2.3.1		not-accessible	Information about THE most important variables for every remote IP address
INT ceSctpAssocRemAddressHtBtFlag	1.3.6.1.4.1.9.10.74.1.2.3.1.5	INTEGER	read-only	The optional Heartbeat associated to one destination transport address could be active or not (value equal to 1 or 0, respectively). An active destination transport address is the one considered available by a peer endpoint for receiving SCTP packets, as it is described in [sctp].
U32 ceSctpAssocRemAddressHtBtTime	1.3.6.1.4.1.9.10.74.1.2.3.1.6	Unsigned32	read-only	The current heartbeat time-out. The recommended default value is 30000 milliseconds.
IP ceSctpAssocRemAddressIP	1.3.6.1.4.1.9.10.74.1.2.3.1.2	InetAddress	not-accessible	The value of a remote IP address available for this association. An InetAddress value is always interpreted within the context of an InetAddressType value.
IPt ceSctpAssocRemAddressIPType	1.3.6.1.4.1.9.10.74.1.2.3.1.1	InetAddressType	not-accessible	Internet type of a remote IP address available for this association. - unknown (0) An unknown address type. This value MUST be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address different from IPv4 or IPv6. This value is used in this MIB for error conditions. - ipv4 (1): An IPv4 address as defined by the InetAddressIPv4 textual convention [RFC2851]. - ipv6 (2): An IPv6 address as defined by the InetAddressIPv6 textual convention [RFC2851].
U32 ceSctpAssocRemAddressMaxRetran	1.3.6.1.4.1.9.10.74.1.2.3.1.7	Unsigned32	read-only	Maximum number of DATA retransmissions allowed to a remote IP address before it is considered inactive, as defined in [sctp]. Recommended value 5 attempts.
C64 ceSctpAssocRemAddressRetransCnt	1.3.6.1.4.1.9.10.74.1.2.3.1.8	Counter64	read-only	Number of DATA retransmissions as defined in [sctp].
ROW ceSctpAssocRemAddressRowStatus	1.3.6.1.4.1.9.10.74.1.2.3.1.10	RowStatus	read-only	An object that allows entries in this table to be created and deleted using the RowStatus convention. A row in this table will be created per remote IP address defined for this association. The creation takes part when a new row in the sctpAssocTable is created or when a new IP address is added in the remote interface (if this function is enabled by the SCTP layer). A row in this table will be deleted per remote IP address reserved for the association when the corresponding row in sctpAssocTable is deleted or when an IP address is removed from the local interface (if this function is enabled by the SCTP layer).
U32 ceSctpAssocRemAddressRTO	1.3.6.1.4.1.9.10.74.1.2.3.1.4	Unsigned32	read-only	The current Retransmision Time-Out. T3-rtx timer as defined in the protocol SCTP.
U32 ceSctpAssocRemAddressSRTT	1.3.6.1.4.1.9.10.74.1.2.3.1.9	Unsigned32	read-only	Smoothed Round Trip Time in milliseconds.
INT ceSctpAssocRemAddressStatus	1.3.6.1.4.1.9.10.74.1.2.3.1.3	INTEGER	read-only	The current status of the remote transport address, according to [SCTP]. active - Destination is alive and active inActive - Destination used as source address only failed - Destination has failed
ceSctpAssocRemAddressTable	1.3.6.1.4.1.9.10.74.1.2.3		not-accessible	Expanded table of ceSctpAssocTable based on the AssocId index. It shows several interesting data for each remote peer IP address which is used in this association.
OCT ceSctpAssocRemHostName	1.3.6.1.4.1.9.10.74.1.2.1.1.11	OCTET STRING	read-only	Peer's DNS name. If no DNS domain name was received at init time (embedded in the INIT or INIT-ACK chunk) from the peer, this entry will be meaningless, therefore it will contain a NULL value. Otherwise, the remote host name received at init time will be stored.
IP ceSctpAssocRemPrimaryAddress	1.3.6.1.4.1.9.10.74.1.2.1.1.15	InetAddress	read-only	Primary destination IP address. An InetAddress value is always interpreted within the context of an InetAddressType value. This value will be filled in after INIT or INIT ACK messages have been received (when the primary path is selected by SCTP).
IPt ceSctpAssocRemPrimaryAddressType	1.3.6.1.4.1.9.10.74.1.2.1.1.14	InetAddressType	read-only	Internet type of primary destination IP address. - unknown (0) An unknown address type. This value MUST be used if the value of the corresponding InetAddress object is a zero-length string. It may also be used to indicate an IP address different from IPv4 or IPv6. This value is used in this MIB for error conditions. - ipv4 (1): An IPv4 address as defined by the InetAddressIPv4 textual convention [RFC2851]. - ipv6 (2): An IPv6 address as defined by the InetAddressIPv6 textual convention [RFC2851].
U32 ceSctpAssocRemRecWnd	1.3.6.1.4.1.9.10.74.1.2.1.1.31	Unsigned32	read-only	The Remote Receive Window Size for this association.
U32 ceSctpAssocRemRecWndLowMark	1.3.6.1.4.1.9.10.74.1.2.1.1.32	Unsigned32	read-only	Low water mark for Remote Receive Window Size.
C64 ceSctpAssocRemRecWndZeroCnt	1.3.6.1.4.1.9.10.74.1.2.1.1.33	Counter64	read-only	Number of times the Remote Receive window reached zero bytes.
U32 ceSctpAssocRemSCTPPort	1.3.6.1.4.1.9.10.74.1.2.1.1.13	Unsigned32	read-only	Remote SCTP port number used for this association.
ROW ceSctpAssocRowStatus	1.3.6.1.4.1.9.10.74.1.2.1.1.52	RowStatus	read-only	An object that allows entries in this table to be created and deleted using the RowStatus convention. A row in this table will be created after creating the TCB in both sides of the association. The creation of this row implies the creation of at least another row (depending on the number of local and remote addresses) in the tables sctpAssocLocalAddressTable and sctpAssocRemAddressTable. A row is deleted in sctpAssocTable when an association turns down (i.e., when the TCB is deleted according to [sctp] in both sides of the association). The deletion of a row in sctpAssocTable implies the deletion of the tables related to this association (sctpAssocLocalAddressTable and sctpAssocRemAddressTable). Also, a row is deleted in sctpAssocTable when a set operation is received from the manager with destroy option.
U32 ceSctpAssocRtoInitial	1.3.6.1.4.1.9.10.74.1.2.1.1.6	Unsigned32	read-only	Initial value for the Retransmission timer. Recommended value is 3000 milliseconds.
U32 ceSctpAssocRtoMax	1.3.6.1.4.1.9.10.74.1.2.1.1.5	Unsigned32	read-only	The maximum value permitted by a SCTP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. Recommended value is 60000 milliseconds.
U32 ceSctpAssocRtoMin	1.3.6.1.4.1.9.10.74.1.2.1.1.4	Unsigned32	read-only	The minimum value permitted by a SCTP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. Minimum recommended value is 1000 milliseconds. Some telephone applications could require less than 1 second.
INT ceSctpAssocState	1.3.6.1.4.1.9.10.74.1.2.1.1.2	INTEGER	read-only	The state of this SCTP association. As in TCP, the only value which may be set by a management station is deleteTCB. Accordingly, it is appropriate for an agent to return a 'badValue' response if a management station attempts to set this object to any other value. If a management station sets this object to the value deleteTCB(9), then this has the effect of deleting the TCB (as defined in SCTP) of the corresponding association on the managed node, resulting in immediate termination of the association. As an implementation-specific option, an ABORT chunk may be sent from the managed node to the other SCTP endpoint.
ceSctpAssocStatGroup	1.3.6.1.4.1.9.10.74.2.1.5			The sctp group of objects to manage SCTP statistics related to the remote endpoint.
ceSctpAssocTable	1.3.6.1.4.1.9.10.74.1.2.1		not-accessible	A table containing SCTP association-specific information.
ceSctpAssocTablesVariablesGroup	1.3.6.1.4.1.9.10.74.2.1.4			The sctp group of objects to manage specific local and remote SCTP variables (local and remote tables).
U32 ceSctpAssocULPDatagramsQueued	1.3.6.1.4.1.9.10.74.1.2.1.1.34	Unsigned32	read-only	Number of data grams waiting to be sent.
U32 ceSctpAssocULPDatagramsQueuedHigh	1.3.6.1.4.1.9.10.74.1.2.1.1.35	Unsigned32	read-only	High water mark for data grams waiting to be sent.
TIK ceSctpAssocUpTime	1.3.6.1.4.1.9.10.74.1.2.1.1.3	TimeTicks	read-only	Time association has been in established state.
U32 ceSctpAssocValCookieLife	1.3.6.1.4.1.9.10.74.1.2.1.1.7	Unsigned32	read-only	Valid cookie life in the 4-way start-up handshake procedure. Recommended value: 60000 milliseconds.
ceSctpCompliance	1.3.6.1.4.1.9.10.74.2.2.1			The compliance statement for SNMPv3 entities which implement SCTP.
ceSctpCompliances	1.3.6.1.4.1.9.10.74.2.2
ceSctpConformance	1.3.6.1.4.1.9.10.74.2
C32 ceSctpCurrEstabEx	1.3.6.1.4.1.9.10.74.1.1.3	Counter32	read-only	The number of SCTP associations for which the current state is either ESTABLISHED, SHUTDOWN-RECEIVED or SHUTDOWN-PENDING.
ceSctpGeneralVariablesGroup	1.3.6.1.4.1.9.10.74.2.1.1			The sctp group of objects providing for management of SCTP entities. Common parameters for the protocol.
ceSctpGroups	1.3.6.1.4.1.9.10.74.2.1
U32 ceSctpMaxAssociations	1.3.6.1.4.1.9.10.74.1.1.2	Unsigned32	read-only	The maximum number of associations that can be supported by this implementation. set to zero to indicate unlimited.
ceSctpMIB	1.3.6.1.4.1.9.10.74			The MIB module for managing SCTP implementation.
ceSctpObjects	1.3.6.1.4.1.9.10.74.1
ceSctpOtherStatGroup	1.3.6.1.4.1.9.10.74.2.1.3			The sctp group of objects providing for management of SCTP general statistics.
C32 ceSctpPassiveEstab	1.3.6.1.4.1.9.10.74.1.1.5	Counter32	read-only	The number of times that SCTP associations have made a direct transition to the ESTABLISHED state from the CLOSED state: CLOSED -> ESTABLISHED. The remote endpoint has initiated the association attempt.
INT ceSctpRtoAlgorithm	1.3.6.1.4.1.9.10.74.1.1.1	INTEGER	read-only	The algorithm used to determine the timeout value (T3-rtx) used for re-transmitting unacknowledged chunks.
ceSctpScalars	1.3.6.1.4.1.9.10.74.1.1
C32 ceSctpShutdowns	1.3.6.1.4.1.9.10.74.1.1.7	Counter32	read-only	The number of times that SCTP associations have made a direct transition to the CLOSE state from either the SHUTDOWN-SENT state or the SHUTDOWN-ACK-SENT state. Graceful termination of the association.
C64 ceSctpStatBytesRec	1.3.6.1.4.1.9.10.74.1.1.8	Counter64	read-only	Number of bytes received(does not include retransmissions).
C64 ceSctpStatBytesSent	1.3.6.1.4.1.9.10.74.1.1.9	Counter64	read-only	Number of bytes sent(does not include retransmissions).
C64 ceSctpStatChunksDiscard	1.3.6.1.4.1.9.10.74.1.1.10	Counter64	read-only	Number of chunks that were discarded.
C64 ceSctpStatChunksRec	1.3.6.1.4.1.9.10.74.1.1.15	Counter64	read-only	Number of SCTP control and data chunks, received from the peers (no retransmissions included).
C64 ceSctpStatChunksRecControl	1.3.6.1.4.1.9.10.74.1.1.16	Counter64	read-only	Number of SCTP control chucks received from peers (no retransmissions included).
C64 ceSctpStatChunksRecOrdered	1.3.6.1.4.1.9.10.74.1.1.17	Counter64	read-only	Number of SCTP data chunks received that required order to be maintained. (no retransmissions included).
C64 ceSctpStatChunksRecUnOrdered	1.3.6.1.4.1.9.10.74.1.1.18	Counter64	read-only	Number of SCTP data chunks received that do not required order to be maintained. (no retransmissions included).
C64 ceSctpStatChunksReTrans	1.3.6.1.4.1.9.10.74.1.1.23	Counter64	read-only	Number of chunks that were re-transmitted.
C64 ceSctpStatChunksSent	1.3.6.1.4.1.9.10.74.1.1.11	Counter64	read-only	Number of SCTP control and data chunks, sent to the peers (no retransmissions included).
C64 ceSctpStatChunksSentControl	1.3.6.1.4.1.9.10.74.1.1.12	Counter64	read-only	Number of SCTP control chunks sent to the peers (no retransmissions included).
C64 ceSctpStatChunksSentOrdered	1.3.6.1.4.1.9.10.74.1.1.13	Counter64	read-only	Number of SCTP data chunks sent that required order to be maintained. (no retransmissions included).
C64 ceSctpStatChunksSentUnOrdered	1.3.6.1.4.1.9.10.74.1.1.14	Counter64	read-only	Number of SCTP data chunks sent that do not required order to be maintained. (no retransmissions included).
C64 ceSctpStatDatagramsRec	1.3.6.1.4.1.9.10.74.1.1.19	Counter64	read-only	Number datagrams sent(does not include retransmissions).
C64 ceSctpStatDatagramsSent	1.3.6.1.4.1.9.10.74.1.1.20	Counter64	read-only	Number datagrams sent(does not include retransmissions).
ceSctpStateStatGroup	1.3.6.1.4.1.9.10.74.2.1.2			The sctp group of objects to control state changes in the SCTP protocol.
C64 ceSctpStatFragmentedUsrMessages	1.3.6.1.4.1.9.10.74.1.1.21	Counter64	read-only	Number of user messages that have to be fragmented because of the MTU.
C64 ceSctpStatOutOfBlue	1.3.6.1.4.1.9.10.74.1.1.24	Counter64	read-only	Number of out of the blue packets (SCTP packet correctly formed -right checksum- but the receiver is not able to identify the association to which this packet belongs) received by the host.
C64 ceSctpStatReassembledUsrMessages	1.3.6.1.4.1.9.10.74.1.1.22	Counter64	read-only	Number of user messages reassembled.
C32 ceSctpStatT1expired	1.3.6.1.4.1.9.10.74.1.1.25	Counter32	read-only	Number of times that T1 timer expired (timer for sending either INIT or COOKIE-ECHO chunks and receiving an acknowledgment).
C32 ceSctpStatT2expired	1.3.6.1.4.1.9.10.74.1.1.26	Counter32	read-only	Number of times that T2-shutdown timer expired (shutdown timer).
ceSctpTables	1.3.6.1.4.1.9.10.74.1.2

RFC description

Tracks SCTP (Stream Control Transmission Protocol) associations, congestion levels, and datagram queuing on Cisco platforms.

Start monitoring Cisco router/media gateway with SCTP signaling support with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-SCTP-MIB