BWA-DOT11-WLAN-MIB

All MIBs › BWA-DOT11-WLAN-MIB

Organization: BWA Products

Last Updated: 2007-08-14

Category: Wireless and WLAN

Description: Manages IEEE 802.11 wireless LAN radio parameters, association tables, and WLAN service configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is BWA-DOT11-WLAN-MIB?

BWA-DOT11-WLAN-MIB is a vendor MIB for BWA (Broadband Wireless Access) product lines including the BWA VL series, BWA 4900, and BWA-PtP, covering IEEE 802.11 wireless LAN radio configuration and traffic-prioritization features. It exposes configuration objects for MAC-address deny-list actions, VLAN and ToS/IP-precedence/DSCP based prioritization thresholds, and a UDP/TCP port-range table used to prioritize traffic such as RTP/RTCP voice streams over specific port ranges. Its monitoring value lies mainly in wireless QoS and access-control configuration status: administrators can check bwaVLMacAddressDenyListAction to confirm which devices are being blocked, and review the bwaVLUdpPortRangeTable entries to verify voice/video traffic prioritization rules (like bwaVLUdpPortPriRTPRTCP) are correctly applied, which affects call quality and network access control on the wireless link. It builds on the standard IEEE 802.11 (dot11) framework and likely coexists with generic dot11 MIB objects for radio/association state, extending them with BWA's QoS and access-control specifics. It is deployed on BWA-branded point-to-point and point-to-multipoint wireless bridge/access products used for fixed wireless broadband links. Engineers can download the BWA-DOT11-WLAN-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in BWA-DOT11-WLAN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

BWA VL-series / BWA 4900 / BWA-PtP wireless bridge or access unit

Monitoring Examples

An operator inspects bwaVLUdpPortRangeTable, indexed via bwaVLUdpPortRangeNum, to confirm the configured bwaVLUdpPortRangeStart values align with the VoIP RTP/RTCP port range referenced by bwaVLUdpPortPriRTPRTCP, ensuring voice traffic gets prioritized over the wireless link. Checking bwaVLMacAddressDenyListAction and bwaVLIPDSCPThreshold together helps diagnose why a particular client is being blocked or why certain DSCP-marked traffic isn't receiving expected priority, which could explain call quality complaints on a point-to-point wireless backhaul link.

What Can Be Monitored

MAC address deny-list action
VLAN/ToS/DSCP priority thresholds
UDP/TCP port-range prioritization rules
RTP/RTCP port priority setting

Imported Objects

From SNMPv2-SMI

Counter32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
enterprises

How to Use in IPNetwork Monitor

Example using bwaVLTotalRxFramesViaEthernet OID:

Select a BWA (early Alvarion) VL/4900/PtP wireless bridge or access unit (legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type bwaVLTotalRxFramesViaEthernet into the Find box to locate it in the OID tree, then select it and click OK. It reports the applicable to all units. Total number of frames received via the Ethernet port. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
bwa	1.3.6.1.4.1.12394
bwa4900_AU_BS	1.3.6.1.4.1.12394.4.1.41
bwa4900_AU_SA	1.3.6.1.4.1.12394.4.1.42
bwa4900_SU_BD	1.3.6.1.4.1.12394.4.1.51
INT bwaLCountryCodeReApply	1.3.6.1.4.1.12394.1.1.6.25.1	INTEGER	read-write	Applicable to all units. Re-apply country code parameters.
INT bwaLighteAPWorkingMode	1.3.6.1.4.1.12394.1.1.2.16	INTEGER	read-write	Applicable to AU only. Change unit running mode: 0 - VL mode 1 - Mixed cell mode
bwaOID	1.3.6.1.4.1.12394.4
INT bwaVLAccessToDHCP	1.3.6.1.4.1.12394.1.1.4.5	INTEGER	read-write	Applicable to all units. The port to be used for communicating with a DHCP server.
INT bwaVLAccessToNwMng	1.3.6.1.4.1.12394.1.1.3.1	INTEGER	read-write	Applicable to all units. The port to be used for remote management.
INT bwaVLAccessToNwTrap	1.3.6.1.4.1.12394.1.1.3.6	INTEGER	read-write	Applicable to all units. Enables or disables sending of traps.
INT bwaVLAdaptiveModulationAlgorithmOption	1.3.6.1.4.1.12394.1.1.10.9.1	INTEGER	read-write	Applicable to all units. Enables/disables the adaptive modulation level decision mechanism.
INT bwaVLAdaptiveModulationDecisionThresholds	1.3.6.1.4.1.12394.1.1.10.9.5	INTEGER	read-write	Applicable to all units. Defines the setting of thresholds for the rate decision algorithm. high (2) should typically be used when the SNR is lower than 13dB.
bwaVLAdaptiveModulationParams	1.3.6.1.4.1.12394.1.1.10.9
INT bwaVLAdbAdapModOption	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.36	INTEGER	read-only	Applicable to AU/BU Only. The SU/RB adaptive modulation option configuration.
INT bwaVLAdbAge	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.44	INTEGER	read-only	Applicable to AU/BU only. The time since any packet was received from the relevant SU/RB.
INT bwaVLAdbAtpcOption	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.35	INTEGER	read-only	Applicable to AU/BU Only. The SU/RB ATPC option configuration.
INT bwaVLAdbAuthOption	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.42	INTEGER	read-only	Applicable to AU/BU Only. The SU/RB authentication algorithm configuration.
STR bwaVLAdbBootVer	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.34	DisplayString	read-only	Applicable to AU/BU Only. The SU/RB Boot Version.
INT bwaVLAdbBurstModeOption	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.37	INTEGER	read-only	Applicable to AU/BU Only. The SU/RB burst mode option configuration.
INT bwaVLAdbCirMaxDelay	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.29	INTEGER	read-only	Applicable to AU Only. Not applicable to BWA-PtP products. The value configured in the relevant SU for the CIR Maximum Delay parameter.
INT bwaVLAdbCirRx	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.27	INTEGER	read-only	Applicable to AU Only. Not applicable to BWA-PtP products. The value configured in the relevant SU for the CIR: AU to SU parameter.
INT bwaVLAdbCirTx	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.25	INTEGER	read-only	Applicable to AU Only. Not applicable to BWA-PtP products. Read-only. The value configured in the relevant SU for the CIR: SU to AU parameter.
INT bwaVLAdbConcatenationOption	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.39	INTEGER	read-only	Applicable to AU/BU Only. The SU/RB concatenation option configuration.
INT bwaVLAdbCountryCode	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.33	INTEGER	read-only	Applicable to AU/BU Only. The SU/RB supported country code.
STR bwaVLAdbCpldVer	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.32	DisplayString	read-only	Applicable to AU/BU Only. The SU/RB CPLD Version.
INT bwaVLAdbDataEncyptOption	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.43	INTEGER	read-only	Applicable to AU/BU Only. The SU/RB data encryption option configuration.
INT bwaVLAdbDistance	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.30	INTEGER	read-only	Applicable to AU/BU Only. The distance between the SU/RB and the AU/BU (In Kilometers).
C32 bwaVLAdbDroppedFramesTotal	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.8	Counter32	read-only	Applicable to AU/BU only. Counts the total number of frames intended to the SU/RB that were dropped because they were retransmitted to the extent of the maximum allowed number of retransmissions without being acknowledged.
INT bwaVLAdbHwRevision	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.31	INTEGER	read-only	Applicable to AU/BU Only. The SU/RB HW Revision.
INT bwaVLAdbIndex	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.1	INTEGER	read-only	Applicable to AU/BU only. The index of an entry in the AU/BU MAC Address Database table.
MAC bwaVLAdbMacAddress	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.2	MacAddress	read-only	Applicable to AU/BU only. The MAC Address of an SU/RB entry in the MAC Address Database table.
INT bwaVLAdbMaxModulationLevel	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.6	INTEGER	read-only	Applicable to AU/BU only. The value configured in the relevant SU/RB for the Maximum Modulation Level parameter. Modulation Level 8 is not applicable for units with HW revision A.
INT bwaVLAdbMirRx	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.28	INTEGER	read-only	Applicable to AU/BU only. The value configured in the relevant SU/RB for the MIR: AU/BU to SU/RB parameter.
INT bwaVLAdbMirTx	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.26	INTEGER	read-only	Applicable to AU/BU only. The value configured in the relevant SU/RB for the MIR: SU/RB to AU/BU parameter.
INT bwaVLAdbSecurityMode	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.41	INTEGER	read-only	Applicable to AU/BU Only. The SU/RB security mode configuration.
INT bwaVLAdbSNR	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.5	INTEGER	read-only	Applicable to AU/BU only. The average Signal to Noise Ratio in dB of frames received by the AU/BU from the relevant SU/RB.
INT bwaVLAdbStatus	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.3	INTEGER	read-only	Applicable to AU/BU only. The status of the relevant SU/RB.
STR bwaVLAdbSwVersion	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.4	DisplayString	read-only	Applicable to AU/BU only. The SW version of the relevant SU/RB.
C32 bwaVLAdbTxFailedModLevel1	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.17	Counter32	read-only	Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 1.
C32 bwaVLAdbTxFailedModLevel2	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.18	Counter32	read-only	Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 2.
C32 bwaVLAdbTxFailedModLevel3	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.19	Counter32	read-only	Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 3.
C32 bwaVLAdbTxFailedModLevel4	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.20	Counter32	read-only	Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 4.
C32 bwaVLAdbTxFailedModLevel5	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.21	Counter32	read-only	Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 5.
C32 bwaVLAdbTxFailedModLevel6	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.22	Counter32	read-only	Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 6.
C32 bwaVLAdbTxFailedModLevel7	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.23	Counter32	read-only	Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 7.
C32 bwaVLAdbTxFailedModLevel8	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.24	Counter32	read-only	Applicable to AU/BU only. Counts the total number of failures to successfully transmit unicast frames intended to the SU/RB using modulation level 8. Not applicable for units with HW revision A.
C32 bwaVLAdbTxFramesTotal	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.7	Counter32	read-only	Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link.
C32 bwaVLAdbTxSuccessModLevel1	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.9	Counter32	read-only	Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 1.
C32 bwaVLAdbTxSuccessModLevel2	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.10	Counter32	read-only	Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 2.
C32 bwaVLAdbTxSuccessModLevel3	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.11	Counter32	read-only	Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/BU over the wireless link using modulation level 3.
C32 bwaVLAdbTxSuccessModLevel4	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.12	Counter32	read-only	Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 4.
C32 bwaVLAdbTxSuccessModLevel5	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.13	Counter32	read-only	Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 5.
C32 bwaVLAdbTxSuccessModLevel6	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.14	Counter32	read-only	Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/BU over the wireless link using modulation level 6.
C32 bwaVLAdbTxSuccessModLevel7	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.15	Counter32	read-only	Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 7.
C32 bwaVLAdbTxSuccessModLevel8	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.16	Counter32	read-only	Applicable to AU/BU only. Counts the total number of unicast frames (excluding retransmissions) that were successfully transmitted to the SU/RB over the wireless link using modulation level 8. Not applicable for units with HW revision A.
STR bwaVLAdbUnitName	1.3.6.1.4.1.12394.1.1.11.5.1.2.1.45	DisplayString	read-only	Applicable to AU/BU only. The unit name of the relevant SU/RB.
STR bwaVLAdminPassword	1.3.6.1.4.1.12394.1.1.2.8.3	DisplayString	read-write	Applicable to all units. The Administrator password. Accessible only with SNMP Write Community String (administrator password). Up to 8 printable ASCII characters.
INT bwaVLAESEncryptionSupport	1.3.6.1.4.1.12394.1.1.1.18.5	INTEGER	read-only	Applicable to all units. The supported AES Encryption Option.
INT bwaVLAIFS	1.3.6.1.4.1.12394.1.1.6.3	INTEGER	read-write	Applicable to AU and SU. Not applicable to BWA-PtP products. Not applicable if Wireless Link Prioritization is enabled. Arbitration Inter-Frame Spacing (AIFS) value, in slots. This is the number of time slots that define the DIFS. (DIFS=SIFS+AIFS). A value of 1 should be used only in point-to-point applications to allow one unit to have advantage over the other unit.
bwaVLAirInterface	1.3.6.1.4.1.12394.1.1.6
INT bwaVLAllowedBandwidth	1.3.6.1.4.1.12394.1.1.1.18.2.1.3	INTEGER	read-only	Applicable to all units. The bandwidth when using the applicable the sub-band.
STR bwaVLAntennaGain	1.3.6.1.4.1.12394.1.1.6.17	DisplayString	read-write	Applicable to all units. Read-write in units where bwaVLAntennaGainChange is supported. Read-only in units where bwaVLAntennaGainChange is not supported. The net gain (including cable attenuation for detached antennas) of the antenna. Range: 0 - to Maximum EIRP defined by country code + 10 (dBi). A value of -2 (this value is configurable only in factory) means don't care. A value of -1 (this value is configurable only in factory) means that the unit will not transmit until the actual value is configured.
INT bwaVLAntennaGainChange	1.3.6.1.4.1.12394.1.1.1.19	INTEGER	read-only	Applicable to all units. Indicates whether the Antenna Gain parameter is changeable or fixed.
IP bwaVLApClientIpAddress	1.3.6.1.4.1.12394.1.1.3.13	IpAddress	read-write	Applicable to SU/RB unit only. The IP Address of the WIFI WIMAX unit
INT bwaVLApplicableModulationLevel	1.3.6.1.4.1.12394.1.1.6.5.1.2	INTEGER	read-only	Applicable to all units. The applicable modulation level for an entry in the Transmit Power Table. Level 8 is not applicable to units with HW revision A.
INT bwaVLARPBroadcastOverrideFilter	1.3.6.1.4.1.12394.1.1.5.7.3	INTEGER	read-write	Applicable to SU/RB only. Enables or disables the broadcasting of ARP messages, overriding the general *bwaVLEthBroadcastFiltering Ethernet broadcast filtering option.
MAC bwaVLAssociatedAU	1.3.6.1.4.1.12394.1.1.1.10	MacAddress	read-only	Applicable to SU/RB only. Associated AU/BU MAC address.
INT bwaVLAteTestResults	1.3.6.1.4.1.12394.1.1.1.20	INTEGER	read-only	Applicable to all units. Results of ATE Test
bwaVLATPC	1.3.6.1.4.1.12394.1.1.6.13
INT bwaVLAtpcOption	1.3.6.1.4.1.12394.1.1.6.13.1	INTEGER	read-write	Applicable all units. Enabling/disabling the ATPC Algorithm.
bwaVLAU	1.3.6.1.4.1.12394.4.1.1
bwaVLAU_BS	1.3.6.1.4.1.12394.4.1.4
bwaVLAU_EZ	1.3.6.1.4.1.12394.4.1.8
bwaVLAU_SA	1.3.6.1.4.1.12394.4.1.5
bwaVLAUAdbEntry	1.3.6.1.4.1.12394.1.1.11.5.1.2.1		not-accessible	Applicable to AU/BU only. An entry in the AU/BU MAC Address Database table.
INT bwaVLAUAdbResetAllModulationLevelCounters	1.3.6.1.4.1.12394.1.1.11.5.1.1	INTEGER	read-write	Applicable to AU/BU only. To reset all the counters for all SUs/RB in the MAC Address Database.
bwaVLAUAdbTable	1.3.6.1.4.1.12394.1.1.11.5.1.2		not-accessible	Applicable to AU/BU only. AU/BU MAC Address Database table.
NTF bwaVLAUagingTRAP	1.3.6.1.4.1.12394.4.1.3.4			An AU/BU trap indicating that the unit association was aged out and removed from the Association database following its failure to acknowledge a specified number of consecutive frames.
C32 bwaVLAUBeaconsToWireless	1.3.6.1.4.1.12394.1.1.11.2.3.1.1	Counter32	read-only	Applicable to AU/BU only. The number of beacons transmitted to the wireless media.
INT bwaVLAUBurstDurationHighPriority	1.3.6.1.4.1.12394.1.1.7.10.4.5	INTEGER	read-write	Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum duration of burst that can be done by AU with High Priority packets. The time is given in 250 microseconds units
INT bwaVLAUBurstDurationLowPriority	1.3.6.1.4.1.12394.1.1.7.10.4.6	INTEGER	read-write	Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum duration of burst that can be done by AU with Low Priority packets. The time is given in 250 microseconds units
INT bwaVLAUDefaultMulticastKeyID	1.3.6.1.4.1.12394.1.1.9.4	INTEGER	read-write	Applicable to AU/BU only. The key to be used for encryption of multicasts and broadcasts.
INT bwaVLAUDefinedFrequency	1.3.6.1.4.1.12394.1.1.6.12.8	INTEGER	read-write	Applicable to AU/BU with HW revision B and lower (for units with HW revision C and higher replaced by bwaVLAUDefinedFrequencyNew to support a resolution of 0.5 MHz). For 5.8GHz products with SW version below 2.0 this is the frequency in MHz of the AU/BU after the next reset. For units with SW version 2.0 and up this is the frequency in MHz to use when the DFS Option is disabled. For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
STR bwaVLAUDefinedFrequencyNew	1.3.6.1.4.1.12394.1.1.6.12.14	DisplayString	read-write	Applicable to AU/BU. For 5.8GHz products with SW version below 2.0 this is the frequency in MHz of the AU/BU after the next reset. For units with SW version 2.0 and up this is the frequency in MHz to use when the DFS Option is disabled. (Replaces bwaVLAUDefinedFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher). For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
NTF bwaVLAUdisassociatedTRAP	1.3.6.1.4.1.12394.4.1.3.3			An AU/BU trap indicating that an SU/RB has been disassociated from the AU. The AU/BU decides that an SU/RB has been disassociated from it and remove it from the ADB after receiving from another AU/BU a SNAP frame with the SU/RB MAC address. The SNAP frame indicating a network topology change where the SU/RB has associated with another AU/BU will be received if both AUs/BUs are connected to the same Ethernet backbone.
bwaVLAUMacAddressDatabase	1.3.6.1.4.1.12394.1.1.11.5.1
bwaVLAUS_BS	1.3.6.1.4.1.12394.4.1.6
bwaVLAUS_SA	1.3.6.1.4.1.12394.4.1.7
NTF bwaVLAUSUnsupportedSubscriberTypeTRAP	1.3.6.1.4.1.12394.4.1.3.110			Applicable to AUS only. This trap is generated when a subscriber with unsupported type tries to associate to AUS. The AUS supports only SU-3 and SU-6. The first variable of the trap is the subscriber MAC Address. The second variable is the type of subscriber
INT bwaVLAuthenticationAlgorithm	1.3.6.1.4.1.12394.1.1.9.1	INTEGER	read-write	Applicable to all units. Enables/disables the authentication encryption option. openSystem: Authentication messages are not encrypted. sharedKey : Authentication messages are encrypted
INT bwaVLAuthenticationEncryptionSupport	1.3.6.1.4.1.12394.1.1.1.18.3	INTEGER	read-only	Applicable to all units. The supported Authentication Encryption Option.
INT bwaVLAuthenticationPromiscuousMode	1.3.6.1.4.1.12394.1.1.9.6	INTEGER	read-write	Applicable to AU/BU only. Enables/disable the promiscuous mode allowing authentication of and communication with all SUs/RB regardless of their security parameters.
INT bwaVLAutomaticChannelSelection	1.3.6.1.4.1.12394.1.1.6.18.3	INTEGER	read-write	Applicable to AU/BU only. Defines weather the AU/BU shall choose the most noise free channel upon startup after spectrum analysis.
INT bwaVLAutoSubBandFrequencySubsetActive	1.3.6.1.4.1.12394.1.1.6.12.15.2.1.3	INTEGER	read-write	Applicable to SU/RB with SW version 4.0 and higher. The status of an entry in the Auto Sub Band Frequency subset Table. The frequency of an active entry will be included in the final list of frequencies to be used for scanning.
INT bwaVLAutoSubBandFrequencySubsetBandIdx	1.3.6.1.4.1.12394.1.1.6.12.15.2.1.1	INTEGER	read-only	Applicable to SU/RB with SW version 4.0 and higher. The index of the applicable Sub Band. This is the Sub Band ID of the relevant entry in the Country Dependent Parameters table. Serves also as an index of the entry in the Frequency subset Table.
bwaVLAutoSubBandFrequencySubsetEntry	1.3.6.1.4.1.12394.1.1.6.12.15.2.1		not-accessible	Applicable to SU/RB with SW version 4.0 and higher. An entry in the Frequency Subset Table.
STR bwaVLAutoSubBandFrequencySubsetFrequency	1.3.6.1.4.1.12394.1.1.6.12.15.2.1.4	DisplayString	read-only	Applicable to SU/RB with SW version 4.0 and higher. The frequency in MHz of the entry in the Auto Sub Band Frequency Subset table.
INT bwaVLAutoSubBandFrequencySubsetFrequencyIdx	1.3.6.1.4.1.12394.1.1.6.12.15.2.1.2	INTEGER	read-only	Applicable to SU/RB with SW version 4.0 and higher. The index of the applicable frequency in the applicable Sub Band. Serves also as an index of the entry in the Frequency subset Table.
bwaVLAutoSubBandFrequencySubsetTable	1.3.6.1.4.1.12394.1.1.6.12.15.2		not-accessible	Applicable to SU/RB with SW version 4.0 and higher. The Frequency Subset Table that includes all available sub-bands and all the frequencies in these sub-bands.
bwaVLAutoSubBandSelect	1.3.6.1.4.1.12394.1.1.6.12.15
INT bwaVLAutoSubBandSelectedFreqSubset	1.3.6.1.4.1.12394.1.1.6.12.15.1	INTEGER	read-write	Applicable to SU/RB with SW version 4.0 and higher. Apply the selected subset. After the next reset the new subset will be used for scanning.
NTF bwaVLAUwirelessQualityTRAP	1.3.6.1.4.1.12394.4.1.3.20			An AU/BU trap, indicating that the quality of the wireless link (retransmissions rate) has changed and dropped below (Off) or increased above (On) a threshold , defined by the *bwaVLWirelessTrapThreshold. The threshold for AU/BU is a percentage of retransmissions.
INT bwaVLAverageModulationLevel	1.3.6.1.4.1.12394.1.1.11.2.5.3	INTEGER	read-only	Applicable to SU/RB. The average modulation level for successful transmission (rounded to nearest integer) since last reset of the Per Modulation Level counters. Range: 1 to 8.
INT bwaVLAverageReceiveSNR	1.3.6.1.4.1.12394.1.1.11.1	INTEGER	read-only	Applicable to SU/RB only. The average Signal to Noise Ratio of received frames.
STR bwaVLAvgSNRMemoryFactor	1.3.6.1.4.1.12394.1.1.10.7	DisplayString	read-write	Applicable to all units. The weight of history in average SNR calculation. The higher is the value, the higher is the weight of history. Range: -1 (Disregard History) to 32.
bwaVLBestAu	1.3.6.1.4.1.12394.1.1.6.11
INT bwaVLBestAuNoOfScanningAttempts	1.3.6.1.4.1.12394.1.1.6.11.2	INTEGER	read-write	Applicable to SU/RB only. The number of scanning attempts to collect information for the Best AU/BU decision. Range: 1 to 255.
INT bwaVLBestAuSupport	1.3.6.1.4.1.12394.1.1.6.11.1	INTEGER	read-write	Applicable to SU/RB only. Disable/enable the Best AU/BU selection mechanism.
INT bwaVLBridgeAgingTime	1.3.6.1.4.1.12394.1.1.5.2	INTEGER	read-write	Applicable to all units. Bridge aging time for devices on both the Ethernet and wireless link sides. Range: 20 to 2000 seconds.
bwaVLBridgeParameters	1.3.6.1.4.1.12394.1.1.5
INT bwaVLBroadcastRelaying	1.3.6.1.4.1.12394.1.1.5.4	INTEGER	read-write	Applicable to AU only. Not applicable to BWA-PtP products. Enables/disables the relaying of broadcast messages to the wireless link.
INT bwaVLBurstInterval	1.3.6.1.4.1.12394.1.1.10.10.2	INTEGER	read-write	Applicable to all units. Not applicable if Wireless Link Prioritization is enabled. Burst mode interval in milliseconds. Range: 1 to the maximum value as defined in the country specific parameters of the Sub Band (milliseconds).
bwaVLBurstMode	1.3.6.1.4.1.12394.1.1.10.10
INT bwaVLBurstModeOption	1.3.6.1.4.1.12394.1.1.10.10.1	INTEGER	read-write	Applicable to all units. Applicable only if Burst Mode Option is supported by country specific parameters of the Sub Band. Not applicable if Wireless Link Prioritization is enabled. Enables/disable burst mode operation. In SU/RB with HW Revision B or lower blocked(3) value is returned when Security Mode is Wep , Data Encryption Option is Enabled and Burst option is Enabled. In AU/BU with HW Revision B or lower blocked(3) value is returned when Dfs Option is Enabled and Burst mode is enabled.
INT bwaVLBurstModeSupport	1.3.6.1.4.1.12394.1.1.1.18.2.1.8	INTEGER	read-only	Applicable to all units. The supported Burst Mode Option.
INT bwaVLCellDistanceMode	1.3.6.1.4.1.12394.1.1.6.15.1	INTEGER	read-write	Applicable AU/BU only. The selected mode of deciding on Cell Distance.
bwaVLCellDistanceParameters	1.3.6.1.4.1.12394.1.1.6.15
INT bwaVLChangeUnitType	1.3.6.1.4.1.12394.1.1.2.15	INTEGER	read-write	Applicable RB/BU only. Change the unit type between BU and RB.
INT bwaVLCirDownlink	1.3.6.1.4.1.12394.1.1.7.4	INTEGER	read-write	Applicable to SU only. Not applicable to BWA-PtP products. The Committed Information Rate (CIR) from AU to SU. CIR must be below bwaVLMirDownlink value. Range for Set: 0 to 2,048 (Kbps) for SU-3 with SW version below 4.0, 0 to 3,072 (Kbps) for SU-3 with SW version 4.0 and higher, 0 to 3,968 (Kbps) for SU-6 with SW version less than 4.0, 0 to 6,016 (Kbps) for SU-6 with SW version greater than 4.0 0 to 14,976 (Kbps) for SU-24, 0 to 45,056 (Kbps) for SU-BD and SU-54. 0 to 6,016 (Kbps) for SU-I. The actual value (Get) will be the entered value rounded to the nearest multiple of 128 (N*128). BWA-PtP products will return 65535.
INT bwaVLCirUplink	1.3.6.1.4.1.12394.1.1.7.5	INTEGER	read-write	Applicable to SU only. Not applicable to BWA-PtP products. The Committed Information Rate (CIR) from SU to AU. CIR must be below bwaVLMirUplink value. Range for Set: 0 to 2,048 (Kbps) for SU-3, 0 to 3,968 (Kbps) for SU-6 with SW version less than 4.0, 0 to 4,096 (Kbps) for SU-6 with SW version greater than 4.0, 0 to 14,976 (Kbps) for SU-24, 0 to 45,056 (Kbps) for SU-BD and SU-54. 0 to 2,048 (Kbps) for SU-I. The actual value (Get) will be the entered value rounded to the nearest multiple of 128 (N*128). BWA-PtP products will return 65535.
INT bwaVLConcatenationMaxFrameSize	1.3.6.1.4.1.12394.1.1.10.11.3	INTEGER	read-write	Applicable to all units. Defines the maximum size of a concatenated frame. Range: 256 to 2200 (bytes) for BWA PtP products BU/RB14 BU/RB28, or for AU/SU with HW revision A or B. 256 to 4032 (bytes) for AU/SU with HW Revision C or higher and BWA PtP products BU/RB100.
INT bwaVLConcatenationMaximumNumberOfFrames	1.3.6.1.4.1.12394.1.1.10.11.2	INTEGER	read-write	Applicable to all units with SW version 3.X . Not applicable for version 4.0 and higher. Defines the maximum numbers of frames that can be concatenated. Range:2 to 8 (frames).
INT bwaVLConcatenationOption	1.3.6.1.4.1.12394.1.1.10.11.1	INTEGER	read-write	Applicable to all units. Defines the Concatenation option.
bwaVLConcatenationParameters	1.3.6.1.4.1.12394.1.1.10.11
bwaVLConfigurationFileLoading	1.3.6.1.4.1.12394.1.1.2.10.3
STR bwaVLConfigurationFileName	1.3.6.1.4.1.12394.1.1.2.10.3.1	DisplayString	read-write	Applicable to all units. The name of the configuration file to be downloaded/uploaded.
STR bwaVLCountryCode	1.3.6.1.4.1.12394.1.1.1.18.1	DisplayString	read-only	Applicable to all units. The country code and country name or country group name that is supported by the unit.
INT bwaVLCountryCodeLearningBySU	1.3.6.1.4.1.12394.1.1.6.12.12	INTEGER	read-write	Applicable to AU only. Starting with 4.0 it is nor applicable for BWA 4900 and BWA PtP. Defines whether the SUs learn the country code of the AU.
bwaVLCountryCodeParameters	1.3.6.1.4.1.12394.1.1.6.25
bwaVLCountryDependentParameterEntry	1.3.6.1.4.1.12394.1.1.1.18.2.1		not-accessible	Applicable to all units. An entry in the Country Dependent Parameters table.
STR bwaVLCountryDependentParameterFrequencies	1.3.6.1.4.1.12394.1.1.1.18.2.1.2	DisplayString	read-only	Applicable to all units. The frequencies included in the applicable sub-band entry.
bwaVLCountryDependentParameters	1.3.6.1.4.1.12394.1.1.1.18
INT bwaVLCountryDependentParameterTableIdx	1.3.6.1.4.1.12394.1.1.1.18.2.1.1	INTEGER	read-only	Applicable to all units. The sub-band ID of the entry in the Country Dependent Parameters table. Serves also as index for the table entry.
bwaVLCountryDependentParamsTable	1.3.6.1.4.1.12394.1.1.1.18.2		not-accessible	Applicable to all units. A table of country dependent parameters.
C32 bwaVLCRCErrors	1.3.6.1.4.1.12394.1.1.11.2.4.2.2	Counter32	read-only	Applicable to all units. The number of frames received from the wireless media containing CRC errors.
INT bwaVLCurrentAUOperatingFrequency	1.3.6.1.4.1.12394.1.1.6.12.7	INTEGER	read-only	Applicable to AU/BU with HW revision B and lower (for units with HW revision C and higher replaced by bwaVLCurrentUOperatingFrequencyNew to support a resolution of 0.5 MHz). The operating frequency in MHz. For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
STR bwaVLCurrentAUOperatingFrequencyNew	1.3.6.1.4.1.12394.1.1.6.12.13	DisplayString	read-only	Applicable to AU/BU. The operating frequency in MHz. (Replaces bwaVLCurrentAUOperatingFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher). For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
INT bwaVLCurrentEthernetPortState	1.3.6.1.4.1.12394.1.1.1.16	INTEGER	read-only	Applicable to all units. The current Ethernet port state.
bwaVLCurrentFrequencySubsetEntry	1.3.6.1.4.1.12394.1.1.6.12.6.1		not-accessible	Applicable to SU/RB and to AU/BU. An entry in the Current Frequency Subset Table.
INT bwaVLCurrentFrequencySubsetFrequency	1.3.6.1.4.1.12394.1.1.6.12.6.1.2	INTEGER	read-only	Applicable to all units. Not applicable to SU/RB with SW version 4.0 and higher. Applicable to all units with HW revision B and lower (for units with HW revision C and higher replaced by bwaVLCurrentFrequencySubsetFrequencyNew to support a resolution of 0.5 MHz). The frequency in MHz of an entry in the Current Frequency Subset table.
STR bwaVLCurrentFrequencySubsetFrequencyNew	1.3.6.1.4.1.12394.1.1.6.12.6.1.3	DisplayString	read-only	Applicable to all units. Not applicable to SU/RB with SW version 4.0 and higher. The frequency in MHz of an entry in the Current Frequency Subset table. (Replaces bwaVLCurrentFrequencySubsetFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher).
bwaVLCurrentFrequencySubsetTable	1.3.6.1.4.1.12394.1.1.6.12.6		not-accessible	Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. The Current Frequency Subset table. In SU/RB it includes all frequencies that are currently used for scanning. In AU/BU it includes all frequencies that can be used by the DFS mechanism (if applicable)
INT bwaVLCurrentFrequencySubsetTableIdx	1.3.6.1.4.1.12394.1.1.6.12.6.1.1	INTEGER	read-only	Applicable to SU/RB and to AU/BU. An index of an entry in the Current Frequency subset Table. Not applicable to SU/RB with SW version 4.0 and higher.
INT bwaVLCurrentNumOfAssociations	1.3.6.1.4.1.12394.1.1.1.13	INTEGER	read-only	Applicable to AU only. Not applicable to BWA-PtP products. The number of SUs currently associated with the AU. BWA-PtP products return 65535.
STR bwaVLCurrentSUOperatingFrequency	1.3.6.1.4.1.12394.1.1.6.12.9	DisplayString	read-only	Applicable to SU/RB only. The frequency used currently by the unit. For 5.8GHz products with SW version below 2.0 the range is 5740 to 5830 MHz using 10MHz resolution. For units with SW version 2.0 and up the range is as defined in the selected Sub Band.
STR bwaVLCurrentTxPower	1.3.6.1.4.1.12394.1.1.6.5.1.5	DisplayString	read-only	Applicable to SU/RB. The actual transmit power in dBm for the applicable rate. Range: -17 to the maximum value defined by bwaVLMaximumTxPowerRange for the applicable modulation level.
C32 bwaVLDataAndOtherMngFramesToWireless	1.3.6.1.4.1.12394.1.1.11.2.3.1.3	Counter32	read-only	Applicable to AU/BU only. The number of data and management frames transmitted to the wireless media. The count includes one count for each data frame transmitted successfully (excluding retransmissions).
INT bwaVLDataEncryptionOption	1.3.6.1.4.1.12394.1.1.9.3	INTEGER	read-write	Applicable to all units. Enables/disables the data encryption option.
INT bwaVLDataEncryptionSupport	1.3.6.1.4.1.12394.1.1.1.18.4	INTEGER	read-only	Applicable to all units. The supported Data Encryption Option.
bwaVLDataFramesSubmittedToBridge	1.3.6.1.4.1.12394.1.1.11.2.3.5
IP bwaVLDefaultGWAddress	1.3.6.1.4.1.12394.1.1.4.3	IpAddress	read-write	Applicable to all units. Default gateway IP address of the unit.
STR bwaVLDefinedMaximumTxPowerRange	1.3.6.1.4.1.12394.1.1.6.6.1.3	DisplayString	read-only	Applicable to SU/RB only. The allowed range for the bwaVLMaxTxPower parameter at the applicable modulation level . Range: -10 to the maximum allowed power level at the applicable modulation level , in dBm.
INT bwaVLDeleteAllNwIpAddrs	1.3.6.1.4.1.12394.1.1.3.5	INTEGER	read-write	Applicable to all units. Deletes all entries from the Management IP Filter Table.
INT bwaVLDeleteAllNwIpRanges	1.3.6.1.4.1.12394.1.1.3.12	INTEGER	read-write	Applicable to all units. Deletes all entries from the Management IP Ranges Table.
INT bwaVLDeleteAllTrapAddrs	1.3.6.1.4.1.12394.1.1.3.9	INTEGER	read-write	Applicable to all units. Deletes all entries from the Management Trap Table.
INT bwaVLDeleteAllUserFilters	1.3.6.1.4.1.12394.1.1.8.4	INTEGER	read-write	Applicable to SU/RB only. Deletes all entries from the IP Filter Table.
INT bwaVLDeleteOneNwIpAddr	1.3.6.1.4.1.12394.1.1.3.4	INTEGER	read-write	Applicable to all units. 0 - cancel operation. 1..10 - Deletes a single selected entry from the Management IP Filter Table.
INT bwaVLDeleteOneNwIpRange	1.3.6.1.4.1.12394.1.1.3.11	INTEGER	read-write	Applicable to all units. 0 - cancel operation. 1..10 - Deletes a single selected entry from the Management IP Ranges Table.
INT bwaVLDeleteOneTrapAddr	1.3.6.1.4.1.12394.1.1.3.8	INTEGER	read-write	Applicable to all units. 0 - cancel operation. 1..10 - Deletes a single selected entry from the Management Trap Table.
INT bwaVLDeleteOneUserFilter	1.3.6.1.4.1.12394.1.1.8.3	INTEGER	read-write	Applicable to SU/RB only. Deletes a single selected entry from the IP Filter Table.
INT bwaVLDeltaFromMinSNRLevel	1.3.6.1.4.1.12394.1.1.6.13.2	INTEGER	read-write	Applicable AU/BU only. The Minimum SNR Level plus the value of this parameter define the maximum desired level of the average SNR at the AU/BU. If the ATPC Option is enabled, than if the received SNR is above the maximum desired level, the AU/BU will transmit Power-Down messages to the applicable SU/RB. Range: 4 to 20 (dB).
INT bwaVLDFSChannelAvoidancePeriod	1.3.6.1.4.1.12394.1.1.6.12.11.4	INTEGER	read-write	Applicable to AU/BU only. Defines the time after detecting radar signals in a channel of avoiding using the channel or adjacent channels in accordance with the bandwidth. Range: 1 to 60 (minutes).
INT bwaVLDFSChannelCheckTime	1.3.6.1.4.1.12394.1.1.6.12.11.3	INTEGER	read-write	Applicable to AU/BU only. Defines the time the unit checks the channel for presence of radar signals and does not transmit after power up or association or after moving to a new channel due to detecting radar in the used channel. Range: 1 to 3600 (seconds).
INT bwaVLDFSChannelFrequency	1.3.6.1.4.1.12394.1.1.6.12.11.7.1.2	INTEGER	read-only	Applicable to AU/BU with HW revision B and lower (for units with HW revision C and higher replaced by bwaVLDFSChannelFrequency New to support a resolution of 0.5 MHz). The frequency in MHz of a channel in the DFS Radar Detection Channels Table.
STR bwaVLDFSChannelFrequencyNew	1.3.6.1.4.1.12394.1.1.6.12.11.7.1.4	DisplayString	read-only	Applicable to AU/BU. The frequency of a channel in the DFS Radar Detection Channels Table. (Replaces bwaVLDFSChannelFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher).
INT bwaVLDFSChannelIdx	1.3.6.1.4.1.12394.1.1.6.12.11.7.1.1	INTEGER	read-only	Applicable to AU/BU only. Read-only. The index of the entry in the bwaVLDFSRadarDetectionChannelsTable.
INT bwaVLDFSChannelRadarStatus	1.3.6.1.4.1.12394.1.1.6.12.11.7.1.3	INTEGER	read-only	Applicable to AU/BU only. The radar detection status of a channel in bwaVLDFSRadarDetectionChannelTable.
INT bwaVLDFSChannelReuseOption	1.3.6.1.4.1.12394.1.1.6.12.11.9.1	INTEGER	read-write	Applicable to AU/BU only. Enabling/disabling the DFS Channel Reuse Algorithm. Not applicable if DFS Option is not supported by the current Sub Band.
bwaVLDFSChannelReuseParameters	1.3.6.1.4.1.12394.1.1.6.12.11.9
INT bwaVLDFSClearRadarDetectedChannelsAfterReset	1.3.6.1.4.1.12394.1.1.6.12.11.6	INTEGER	read-write	Applicable to AU/BU only. Clear Radar Detected and Adjacent to Radar channels after unit reset. Returns the unit to operate in default frequency.
NTF bwaVLDFSFrequcnyTRAP	1.3.6.1.4.1.12394.4.1.3.107			Applicable to AU/BU only. A trap indicating that the unit moved to a new frequency.
INT bwaVLDFSMaximumNumberOfDetectionsInAssessmentPeriod	1.3.6.1.4.1.12394.1.1.6.12.11.9.3	INTEGER	read-write	Applicable to AU/BU only. Range: 1 to 10 (Times).
INT bwaVLDFSMinimumPulsesToDetect	1.3.6.1.4.1.12394.1.1.6.12.11.8	INTEGER	read-write	Applicable to AU/BU only. Defines the minimum number of pulses to detect a radar. Range: 1 - 100.
INT bwaVLDFSMoveFreq	1.3.6.1.4.1.12394.1.1.14.11	INTEGER	read-only	Applicable to AU/BU with HW revision B and lower (for units with HW revision C and higher replaced by bwaVLTrapDFSMoveFreq New to support a resolution of 0.5 MHz). The new frequency in MHz after detecting radar on a previous channel.
STR bwaVLDFSMoveFreqNew	1.3.6.1.4.1.12394.1.1.14.12	DisplayString	read-only	Applicable to AU/BU. The new frequency in MHz after detecting radar on a previous channel. (Replaces bwaVLDFSMoveFreq to support a resolution of 0.5 MHz for units with HW revision C and higher).
NTF bwaVLDFSNoFreeChannelsExistsTRAP	1.3.6.1.4.1.12394.4.1.3.108			Applicable to AU/BU only. A trap indicating that a radar was detected and there is no free channel.
INT bwaVLDFSOption	1.3.6.1.4.1.12394.1.1.6.12.11.1	INTEGER	read-write	Applicable to AU/BU only. Enabling/disabling the DFS Algorithm. Not applicable if DFS Option is not supported by the current Sub Band.
bwaVLDFSParameters	1.3.6.1.4.1.12394.1.1.6.12.11
INT bwaVLDFSRadarActivityAssessmentPeriod	1.3.6.1.4.1.12394.1.1.6.12.11.9.2	INTEGER	read-write	Applicable to AU/BU only. Range: 1 to 12 (Houres).
NTF bwaVLDFSRadarDetecetedTRAP	1.3.6.1.4.1.12394.4.1.3.106			DFS: Applicable to AU/BU only. A trap indicating that a radar was detected.
bwaVLDFSRadarDetectionChannelsEntry	1.3.6.1.4.1.12394.1.1.6.12.11.7.1		not-accessible	Applicable to AU/BU only. An entry in the bwaVLDFSRadarDetectionChannelsTable.
bwaVLDFSRadarDetectionChannelsTable	1.3.6.1.4.1.12394.1.1.6.12.11.7		not-accessible	Applicable to AU/BU only. Applicable only when DFS option is on. Displays the current channels defined in the sub-band and their radar detection status.
INT bwaVLDfsSupport	1.3.6.1.4.1.12394.1.1.1.18.2.1.10	INTEGER	read-only	Applicable to AU/BU only. The supported Dfs Option.
INT bwaVLDFSSuWaitingOption	1.3.6.1.4.1.12394.1.1.6.12.11.5	INTEGER	read-write	Applicable to AU/BU only. Defines whether the associated SUs should wait for this AU/BU after it stopped transmitting due to radar detection, before they starts scanning for other AUs/BUs.
INT bwaVLDHCPBroadcastOverrideFilter	1.3.6.1.4.1.12394.1.1.5.7.1	INTEGER	read-write	Applicable to SU/RB only. Enables or disables the broadcasting of DHCP messages, overriding the general *bwaVLEthBroadcastFiltering Ethernet broadcast filtering option.
INT bwaVLDHCPUnicastOverrideFilter	1.3.6.1.4.1.12394.1.1.8.5	INTEGER	read-write	Applicable to SU/RB only. Enables or disables the unicast DHCP messages, overriding the IP Filtering option.
bwaVLDisassociate	1.3.6.1.4.1.12394.1.1.6.20
INT bwaVLDisassociateAllSUs	1.3.6.1.4.1.12394.1.1.6.20.1	INTEGER	read-write	Applicable to AU only. The AU shall disassociate all its associated units.
MAC bwaVLDisassociateSuByMacAddress	1.3.6.1.4.1.12394.1.1.6.20.2	MacAddress	read-write	Applicable to AU only. The AU shall disassociate the SU with the configured MAC address.
bwaVLDrap	1.3.6.1.4.1.12394.1.1.7.11
bwaVLDrapGatewayEntry	1.3.6.1.4.1.12394.1.1.11.8.1		not-accessible	A Drap Gateway Entry.
INT bwaVLDrapGatewayIndex	1.3.6.1.4.1.12394.1.1.11.8.1.1	INTEGER	read-only	Gateway Entry's Index
IP bwaVLDrapGatewayIP	1.3.6.1.4.1.12394.1.1.11.8.1.2	IpAddress	read-only	The IP address of the Gateway
INT bwaVLDrapGatewayNoOfActiveVoiceCalls	1.3.6.1.4.1.12394.1.1.11.8.1.4	INTEGER	read-only	The current number of active voice calls handled by the Gateway
bwaVLDrapGatewaysTable	1.3.6.1.4.1.12394.1.1.11.8		not-accessible	This table provides information about Gateways supporting DRAP that are registered at the AU
INT bwaVLDrapGatewayType	1.3.6.1.4.1.12394.1.1.11.8.1.3	INTEGER	read-only	The Gateway type
INT bwaVLDrapMaxNumberOfVoiceCalls	1.3.6.1.4.1.12394.1.1.7.11.3	INTEGER	read-write	Applicable to AU when DRAP support is enabled. Not applicable to BWA PtP products. The maximum number of voice calls that can be supported by the AU
INT bwaVLDrapNoOfActiveVoiceCalls	1.3.6.1.4.1.12394.1.1.7.11.5	INTEGER	read-only	Applicable to AU when DRAP support is enabled. Not applicable to BWA PtP products. The current total number of active voice calls.
INT bwaVLDrapSupport	1.3.6.1.4.1.12394.1.1.7.11.1	INTEGER	read-write	Applicable to AU. Not applicable to BWA PtP products. Disable/Enable the DRAP feature
INT bwaVLDrapTTL	1.3.6.1.4.1.12394.1.1.7.11.4	INTEGER	read-write	Applicable to AU when DRAP support is enabled. Not applicable to BWA PtP products. The maximum time between two allocation requests
INT bwaVLDrapUdpPort	1.3.6.1.4.1.12394.1.1.7.11.2	INTEGER	read-write	Applicable to AU when DRAP support is enabled. Not applicable to BWA PtP products. The UDP port used for the DRAP server
C32 bwaVLDroppedFrameEvents	1.3.6.1.4.1.12394.1.1.11.2.4.1.1	Counter32	read-only	Applicable to all units. The number of frames that were dropped because they were retransmitted to the maximum allowed number of retransmissions without being acknowledged.
INT bwaVLEraseEventLog	1.3.6.1.4.1.12394.1.1.2.12.2	INTEGER	read-write	Applicable to all units. Erase the event log.
STR bwaVLESSID	1.3.6.1.4.1.12394.1.1.6.1.1	DisplayString	read-write	Applicable to all units. The Extended Service Set ID (ESSID) used to prevent the merging of collocated systems. The ESSID is accessible only with the write community string (administrator password). Up to 31 printable case sensitive ASCII characters.
bwaVLESSIDParameters	1.3.6.1.4.1.12394.1.1.6.1
INT bwaVLEthBroadcastFiltering	1.3.6.1.4.1.12394.1.1.5.6	INTEGER	read-write	Applicable to SU/RB only. Enables/disables the filtering of Ethernet (layer2) broadcasts. disable : No filtering. onEthernetOnly : Filters broadcasts received on the Ethernet port only. onWirelessOnly : Filters broadcasts received on the Wlan port only. onBothWirelessAndEth: Filters broadcasts received on both ports.
bwaVLEthBroadcastingParameters	1.3.6.1.4.1.12394.1.1.5.7
INT bwaVLEthBroadcastMulticastLimiterOption	1.3.6.1.4.1.12394.1.1.5.7.4	INTEGER	read-write	Applicable to all units. Enable/disable the limiter for multicast and broadcast packets.
INT bwaVLEthBroadcastMulticastLimiterSendTrapInterval	1.3.6.1.4.1.12394.1.1.5.7.6	INTEGER	read-write	Applicable to all units. The minimum time between two successive traps that are sent indicating the number of packets that were dropped by the Ethernet Broadcast/Multicast Limiter since the last trap was sent. Range: 1 to 60 minutes
INT bwaVLEthBroadcastMulticastLimiterThreshold	1.3.6.1.4.1.12394.1.1.5.7.5	INTEGER	read-write	Applicable to all units. The limit on the number of multicast and broadcast packets when the Ethernet Broadcast/Multicast Limiter Option is enabled. Range: 0 to 204800
NTF bwaVLEthBroadcastMulticatLimiterTRAP	1.3.6.1.4.1.12394.4.1.3.109			Applicable to all units. The trap is send if the ethernet broadcast filter threshold is exceeded and it contains the number of dropped packets.
INT bwaVLEthBroadcastThresholdExceeded	1.3.6.1.4.1.12394.1.1.14.13	INTEGER	read-only	Applicable to all units. The number of packets that are dropped by the ethernet broadcast/multicast limiter.
bwaVLEthCounters	1.3.6.1.4.1.12394.1.1.11.2.2
INT bwaVLEthernetLinkType	1.3.6.1.4.1.12394.1.1.5.1.2	INTEGER	read-write	Applicable to all units. VLAN support mode (Link Type). The Access Link option is not available for AU/BU. Service Provider Link is not available for BU/RB.
INT bwaVLEthernetNegotiationMode	1.3.6.1.4.1.12394.1.1.2.9	INTEGER	read-write	Applicable to all units. The speed/duplex mode of the Ethernet port.
INT bwaVLEthernetPortControl	1.3.6.1.4.1.12394.1.1.5.11.1	INTEGER	read-write	Applicable to SU/RB only. Enable/disable the Ethernet port. When disabled, only data frames are blocked. Management frames are accepted.
STR bwaVLEventLogDestinationDir	1.3.6.1.4.1.12394.1.1.2.10.4.2	DisplayString	read-write	Applicable to all units. The destination directory of the event log file. Up to 80 printable ASCII characters. Use dot (.) To clear field.
STR bwaVLEventLogFileName	1.3.6.1.4.1.12394.1.1.2.10.4.1	DisplayString	read-write	Applicable to all units. The name of the Event Log file to be uploaded.
bwaVLEventLogFileParams	1.3.6.1.4.1.12394.1.1.2.12
bwaVLEventLogFileUploading	1.3.6.1.4.1.12394.1.1.2.10.4
INT bwaVLEventLogPolicy	1.3.6.1.4.1.12394.1.1.2.12.1	INTEGER	read-write	Applicable to all units. The lowest level event to be registered in the event log.
INT bwaVLExecuteFTPConfigurationFileLoading	1.3.6.1.4.1.12394.1.1.2.10.3.4	INTEGER	read-write	Applicable to all units. Execution of the file download/upload operation.
INT bwaVLExitTelnet	1.3.6.1.4.1.12394.1.1.2.7	INTEGER	read-write	Applicable to all units. Exit the management via Telnet program.
INT bwaVLFairnessFactor	1.3.6.1.4.1.12394.1.1.6.15.2	INTEGER	read-write	Applicable AU/BU only. Not applicable to BWA-PtP products for SW version below 4.0.. The percentage of the maximum distance that is taken into account in the time slot calculation. Range: 0 to 100 (Percent). A value of 0 means the minimal slot size (9 microseconds). BWA-PtP products with SW version below 4.0 return na.
bwaVLFeatureUpgrade	1.3.6.1.4.1.12394.1.1.2.14
STR bwaVLFeatureUpgradeManually	1.3.6.1.4.1.12394.1.1.2.14.1	DisplayString	read-write	Applicable to all units. Upgrade unit to support new feature. Enter your license number (32 to 64 hex digits).
INT bwaVLFlashMemoryControl	1.3.6.1.4.1.12394.1.1.2.4	INTEGER	read-write	Applicable to all units. resetAndBootFromShadowVersion : Activates the backup version. useRunningVersionAfterReset : The currently active version will become the main version and will be activated after next reset.
C32 bwaVLFramesDelayedDueToSwRetry	1.3.6.1.4.1.12394.1.1.11.2.4.1.2	Counter32	read-only	Applicable to all units. Not applicable for units with SW Version 3.0 and higher. The number of frames that were delayed because the SW retry algorithm was activated on a previous frame designated for the same recipient.
C32 bwaVLFramesDropped	1.3.6.1.4.1.12394.1.1.11.2.3.4	Counter32	read-only	Applicable to all units. The number of dropped frames. The frames that were retransmitted to the extent of the maximum allowed number of retransmissions without being acknowledged..
C32 bwaVLFramesSubmittedViaHighQueue	1.3.6.1.4.1.12394.1.1.11.2.3.5.1	Counter32	read-only	Applicable to all units. Frames submitted to the internal bridge via the High priority queue. for transmission to the wireless media.
C32 bwaVLFramesSubmittedViaLowQueue	1.3.6.1.4.1.12394.1.1.11.2.3.5.3	Counter32	read-only	Applicable to all units. Frames submitted to the internal bridge via the Low priority queue for transmission to the wireless media.
C32 bwaVLFramesSubmittedViaMidQueue	1.3.6.1.4.1.12394.1.1.11.2.3.5.2	Counter32	read-only	Applicable to all units. Frames submitted to the internal bridge via the Mid priority queue for transmission to the wireless media.
bwaVLFrequencyDefinition	1.3.6.1.4.1.12394.1.1.6.12
INT bwaVLFrequencySubsetActive	1.3.6.1.4.1.12394.1.1.6.12.4.1.3	INTEGER	read-write	Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. The status of an entry in the Frequency subset Table. The frequency of an active entry will be included in the final list of frequencies to be used for scanning.
bwaVLFrequencySubsetEntry	1.3.6.1.4.1.12394.1.1.6.12.4.1		not-accessible	Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. An entry in the Frequency Subset Table.
INT bwaVLFrequencySubsetFrequency	1.3.6.1.4.1.12394.1.1.6.12.4.1.2	INTEGER	read-only	Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. Applicable to all units with HW revision B and lower (for units with HW revision C and higher replaced by bwaVLFrequencySubsetFrequencyNew to support a resolution of 0.5 MHz). The frequency in MHz of an entry in the Frequency Subset table.
STR bwaVLFrequencySubsetFrequencyNew	1.3.6.1.4.1.12394.1.1.6.12.4.1.4	DisplayString	read-write	Applicable to all units. Not applicable to SU/RB with SW version 4.0 and higher. The frequency in MHz of an entry in the Frequency Subset table. (Replaces bwaVLFrequencySubsetFrequency to support a resolution of 0.5 MHz for units with HW revision C and higher).
bwaVLFrequencySubsetTable	1.3.6.1.4.1.12394.1.1.6.12.4		not-accessible	Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. The Frequency Subset Table that includes all frequencies from the selected Sub-band.
INT bwaVLFrequencySubsetTableIdx	1.3.6.1.4.1.12394.1.1.6.12.4.1.1	INTEGER	read-only	Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. An index of an entry in the Frequency subset Table.
IP bwaVLFTPClientIPAddress	1.3.6.1.4.1.12394.1.1.2.10.1.3	IpAddress	read-write	Applicable to all units. For SW version higher than 4.0 this is read-only. The IP address of the FTP stack in the unit.
IP bwaVLFTPClientMask	1.3.6.1.4.1.12394.1.1.2.10.1.5	IpAddress	read-write	Applicable to all units. The Mask of the FTP stack in the unit.
STR bwaVLFTPConfigurationFileSourceDir	1.3.6.1.4.1.12394.1.1.2.10.3.3	DisplayString	read-write	Applicable to all units. The source directory of the required file in the FTP server. Up to 80 printable ASCII characters. Use dot (.) To clear field
INT bwaVLFTPDownloadSwFile	1.3.6.1.4.1.12394.1.1.2.10.2.3	INTEGER	read-write	Applicable to all units. Execution of the SW download operation
IP bwaVLFTPGatewayIpAddress	1.3.6.1.4.1.12394.1.1.2.10.1.6	IpAddress	read-write	Applicable to all units. The FTP Gateway address
bwaVLFTPParameters	1.3.6.1.4.1.12394.1.1.2.10
IP bwaVLFTPServerIpAddress	1.3.6.1.4.1.12394.1.1.2.10.1.4	IpAddress	read-write	Applicable to all units. The IP address of the FTP server.
bwaVLFTPServerParams	1.3.6.1.4.1.12394.1.1.2.10.1
STR bwaVLFTPServerPassword	1.3.6.1.4.1.12394.1.1.2.10.1.2	DisplayString	read-write	Applicable to all units. The password to be used for access to the FTP server. Accessible only with SNMP Write Community String (administrator password).
STR bwaVLFTPServerUserName	1.3.6.1.4.1.12394.1.1.2.10.1.1	DisplayString	read-write	Applicable to all units. The user name to be used for access to the FTP server. Accessible only with SNMP Write Community String (administrator password).
bwaVLFTPSwDownload	1.3.6.1.4.1.12394.1.1.2.10.2
STR bwaVLFTPSwFileName	1.3.6.1.4.1.12394.1.1.2.10.2.1	DisplayString	read-write	Applicable to all units. The name of the SW file to be downloaded.
STR bwaVLFTPSwSourceDir	1.3.6.1.4.1.12394.1.1.2.10.2.2	DisplayString	read-write	Applicable to all units. The source directory of the required file in the FTP server. Up to 80 printable ASCII characters. Use dot (.) To clear field
INT bwaVLGracefulDegradationLimit	1.3.6.1.4.1.12394.1.1.7.8	INTEGER	read-write	Applicable to AU only. Not applicable to BWA-PtP products. The maximum limit for activating the graceful degradation algorithm. Range: 0 to 70% rate of the CIR. BWA-PtP products return 255.
INT bwaVLHardwareRetries	1.3.6.1.4.1.12394.1.1.10.8	INTEGER	read-write	Applicable to all units. Not applicable if Wireless Link Prioritization is enabled. The maximum number of trials to transmit an unacknowledged frame in each Hardware Retrial phase. Range : 1 to 14.
INT bwaVLHWRetriesHighPriority	1.3.6.1.4.1.12394.1.1.7.10.4.3	INTEGER	read-write	Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum number of HW Retries for a unicast data packet that has High Priority
INT bwaVLHWRetriesLowPriority	1.3.6.1.4.1.12394.1.1.7.10.4.4	INTEGER	read-write	Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum number of HW Retries for a unicast data packet that has Low Priority
STR bwaVLInstallerPassword	1.3.6.1.4.1.12394.1.1.2.8.2	DisplayString	read-write	Applicable to all units. The Installer password. Up to 8 printable ASCII characters.
INT bwaVLIPDSCPThreshold	1.3.6.1.4.1.12394.1.1.7.10.2.3	INTEGER	read-write	Applicable to all units. The threshold of DSCP sub-field of IP ToS field from IP Header (RFC2474) to be used when ToS Prioritization Option is set to DSCP. If the DSCP sub-field of a frame is less than or equal to this threshold the frame will have LOW priority, otherwise it will get HIGH priority.
bwaVLIpFilterEntry	1.3.6.1.4.1.12394.1.1.8.2.1		not-accessible	Applicable to SU/RB only. An IP Filter Table entry.
INT bwaVLIpFilterIdx	1.3.6.1.4.1.12394.1.1.8.2.1.4	INTEGER	read-only	Applicable to SU/RB only. A table index for the IP Filter Table entry.
INT bwaVLIpFilterRange	1.3.6.1.4.1.12394.1.1.8.2.1.3	INTEGER	read-write	Applicable to SU/RB only. An addresses range for the IP Filter Table entry. The first address in the range is the IP address. O means that the range is not used. Either a mask or a range, but not both can be used to define an address group. If the range is other than 0, than the mask is ignored and only the range value is used to define the address group. Range: 0 to 255.
bwaVLIpFilterTable	1.3.6.1.4.1.12394.1.1.8.2		not-accessible	Applicable to SU/RB only. An IP Filter Table of up to 8 user defined addresses, or address groups, to be used if the selected User Filtering option is userDefinedAddrOnly.
IP bwaVLIpID	1.3.6.1.4.1.12394.1.1.8.2.1.1	IpAddress	read-write	Applicable to SU/RB only. An IP address of an IP Filter Table entry.
bwaVLIpParams	1.3.6.1.4.1.12394.1.1.4
INT bwaVLIPPrecedenceThreshold	1.3.6.1.4.1.12394.1.1.7.10.2.2	INTEGER	read-write	Applicable to all units. The threshold of Precedence sub-field of IP ToS field from IP Header (RFC791) to be used when the ToS Prioritization Option is set to IP Precedence. If the Precedence sub-field of a frame is less than or equal to this threshold the frame will have LOW priority, otherwise it will get HIGH priority.
STR bwaVLKey1	1.3.6.1.4.1.12394.1.1.9.7	DisplayString	read-write	Applicable to all units. Key number 1. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits.
STR bwaVLKey2	1.3.6.1.4.1.12394.1.1.9.8	DisplayString	read-write	Applicable to all units. Key number 2. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits.
STR bwaVLKey3	1.3.6.1.4.1.12394.1.1.9.9	DisplayString	read-write	Applicable to all units. Key number 3. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits.
STR bwaVLKey4	1.3.6.1.4.1.12394.1.1.9.10	DisplayString	read-write	Applicable to all units. Key number 4. Accessible only with SNMP Write Community String (administrator password). Valid values: 32 hexadecimal digits.
INT bwaVLLoadingStatus	1.3.6.1.4.1.12394.1.1.2.11	INTEGER	read-only	Applicable to all units. The status of the last loading operation.
NTF bwaVLLoadingStatusTRAP	1.3.6.1.4.1.12394.4.1.3.104			Applicable to all units. A trap indicating that last FTP/TFTP loading process has been finished successfully or failed.
INT bwaVLLostBeaconsWatchdogThreshold	1.3.6.1.4.1.12394.1.1.6.22	INTEGER	read-write	Applicable to AU/BU only. The number of unsuccessful consecutive transmissions beacons before Internal refresh is performed. 0 means that the lost beacons watchdog is not used and internal refresh is not performed.
INT bwaVLlowPriorityAIFS	1.3.6.1.4.1.12394.1.1.7.10.4.2	INTEGER	read-write	Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Define the AIFS (Arbitration Inter-frame Space) that will be used for transmitting Low Priority Traffic
INT bwaVLLowPriorityTrafficMinimumPercent	1.3.6.1.4.1.12394.1.1.7.12	INTEGER	read-write	The minimum percent of the traffic rate that is allocated to the low priority traffic
bwaVLMacAddressDatabase	1.3.6.1.4.1.12394.1.1.11.5
bwaVLMacAddressDenyList	1.3.6.1.4.1.12394.1.1.5.10
INT bwaVLMacAddressDenyListAction	1.3.6.1.4.1.12394.1.1.5.10.5	INTEGER	read-write	Applicable to AU only. Define the action to be used by the Mac Address Deny List. allowedList(2) means that the list becomes Allow list.
MAC bwaVLMacAddressDenyListAdd	1.3.6.1.4.1.12394.1.1.5.10.2	MacAddress	read-write	Applicable to AU only. Not applicable to BWA-PtP units. Add a MAC address to the MAC Address Deny List Table
bwaVLMacAddressDenyListEntry	1.3.6.1.4.1.12394.1.1.5.10.1.1		not-accessible	Applicable to AU only. Not applicable to BWA-PtP units. An entry in the Mac Address Deny List Table.
MAC bwaVLMacAddressDenyListId	1.3.6.1.4.1.12394.1.1.5.10.1.1.2	MacAddress	read-write	Applicable to AU only. Not applicable to BWA-PtP units. The list of MAC Addresses in the Mac Address Deny List Table. To Remove a MAC Address - SET the corresponding entry to 0. To Add a new MAC Address - SET an entry which is currently 0.
MAC bwaVLMacAddressDenyListRemove	1.3.6.1.4.1.12394.1.1.5.10.3	MacAddress	read-write	Applicable to AU only. Not applicable to BWA-PtP units. Delete a MAC address from the MAC Address Deny List Table
bwaVLMacAddressDenyListTable	1.3.6.1.4.1.12394.1.1.5.10.1		not-accessible	Applicable to AU only. Not applicable to BWA-PtP units. A list of up to 100 MAC Addresses of SUs. If bwaVLMacAddressDenyListAction is set to denyList, these are SUs that are not allowed to transfer data to the AU. If bwaVLMacAddressDenyListAction is set to allowList, only these SUs are allowed to transfer data to the AU.
INT bwaVLMacAddressDenyListTableIdx	1.3.6.1.4.1.12394.1.1.5.10.1.1.1	INTEGER	read-only	Applicable to AU only. Not applicable to BWA-PtP units. A read only table index for a MAC Address entry in the Mac Address Deny List Table. Range: 1 to 100.
bwaVLMacPinpoint	1.3.6.1.4.1.12394.1.1.11.7
bwaVLMacPinpointEntry	1.3.6.1.4.1.12394.1.1.11.7.1.1		not-accessible	Applicable to AU/BU only. An entry in the MAC Pinpoint Table. Each entry contains an Ethernet station MAC address and the MAC address of the wireless device used to connect it to the wireless network
bwaVLMacPinpointTable	1.3.6.1.4.1.12394.1.1.11.7.1		not-accessible	Applicable to AU/BU only. A table that contains information about wireless device used by a certain Ethernet station in order to connect to the wireless network
STR bwaVLMainVersionFileName	1.3.6.1.4.1.12394.1.1.1.5	DisplayString	read-only	Applicable to all units. Main software version file name.
STR bwaVLMainVersionNumber	1.3.6.1.4.1.12394.1.1.1.4	DisplayString	read-only	Applicable to all units. Main software version number.
INT bwaVLManagementVlanID	1.3.6.1.4.1.12394.1.1.5.1.3	INTEGER	read-write	Applicable to all units. VLAN ID for management frame tagging. Range: 1 to 4094, 65535 for No VLAN tagging.
IP bwaVLMaskID	1.3.6.1.4.1.12394.1.1.8.2.1.2	IpAddress	read-write	Applicable to SU/RB only. An IP Mask of an IP Filter Table entry. Either a mask or a range, but not both can be used to define an address group. If the range is other than 0, than the mask is ignored and only the range value is used to define the address group.
INT bwaVLMaxBurstDuration	1.3.6.1.4.1.12394.1.1.7.7	INTEGER	read-write	Applicable to AU and SU. Not applicable to BWA-PtP products. The maximum time during which inactivity bonus time can be accumulated for future burst transmissions. Range: 0 to 2000 milliseconds. BWA-PtP products return 65535
INT bwaVLMaxContentionWindow	1.3.6.1.4.1.12394.1.1.10.4	INTEGER	read-write	Applicable to SU and AU. For units bearing SW version 4.0 and above applicable to BWA PtP products, for previous SW versions not applicable to BWA PtP products. The maximum value to be used by the contention window calculation algorithm. Value must be power of 2 minus 1 (7,15,31...) Range: 7 to 1023.
INT bwaVLMaxDelay	1.3.6.1.4.1.12394.1.1.7.6	INTEGER	read-write	Applicable to SU only. Not applicable to BWA-PtP products. The maximal time packets may be delayed by the CIR\MIR mechanism. Above the configured maximal period the packets are discarded. Range: 300 to 10000 milliseconds. BWA-PtP products return 65535.
INT bwaVLMaximumBurstDuration	1.3.6.1.4.1.12394.1.1.1.18.2.1.9	INTEGER	read-only	Applicable to all units. Applicable only if Burst Mode Option is supported. The maximum supported burst duration.
INT bwaVLMaximumCellRadius	1.3.6.1.4.1.12394.1.1.6.2	INTEGER	read-write	Applicable to all units. For AU/BU: read-write. In units with SW version 2.0 and up - applicable only when the Cell Distance Mode is set to Manual. The highest distance from the AU/BU of any SU/RB served by it. Affects the maximum time the units wait for a response message and the slot size by taking into account the round trip propagation delay. For SU/RB: read-only. The distance is learned from the AU/BU. Range: For units below version 2.0 the range is 0 - 50000 Meters. Otherwise - the range is 0 to 54 Kilometers. 0 means no compensation (minimum slot size, maximal delay timeout).
INT bwaVLMaximumModulationLevel	1.3.6.1.4.1.12394.1.1.10.5	INTEGER	read-write	Applicable to all units. If the Adaptive Modulation algorithm is enabled, it sets the Maximum Modulation Level to be used. If The Modulation algorithm is disabled, it sets the Fixed Modulation Level to be used. The range is 1 to 8. 8 is not applicable for units with HW revision A.
bwaVLMaximumTransmitPowerEntry	1.3.6.1.4.1.12394.1.1.6.6.1		not-accessible	Applicable to SU/RB only. An entry in the Maximum Transmit Power Table.
INT bwaVLMaximumTransmitPowerIdx	1.3.6.1.4.1.12394.1.1.6.6.1.1	INTEGER	read-only	Applicable to SU/RB only. An index of an entry in the Maximum Transmit Power Table.
bwaVLMaximumTransmitPowerTable	1.3.6.1.4.1.12394.1.1.6.6		not-accessible	Applicable to SU/RB only. A table of maximum transmit power parameters.
INT bwaVLMaximumTxPower	1.3.6.1.4.1.12394.1.1.6.24	INTEGER	read-write	Applicable to only SU/RB with SW version 4.0 and higher. The Maximum Transmit Power for all modulation levels. The Maximum Transmit Power for a specific modulation level is the minimum between this parameter and the hardware limitation for that modulation level
STR bwaVLMaximumTxPowerRange	1.3.6.1.4.1.12394.1.1.6.5.1.3	DisplayString	read-only	Applicable to all units. The allowed range for the bwaVLTxPower parameter at the applicable modulation level . Range: -10 to the maximum allowed power level at the applicable modulation level , in dBm.
INT bwaVLMaxModulationLevel	1.3.6.1.4.1.12394.1.1.1.18.2.1.7	INTEGER	read-only	Applicable to all units. The maximum supported modulation level.
INT bwaVLMaxNumOfAssociations	1.3.6.1.4.1.12394.1.1.6.10	INTEGER	read-write	Applicable to AU only. Not applicable to BWA-PtP products. Sets the upper limit for the number of SUs that can be associated with the AU. Range: For regular AUs (AU-BS, AU-SA) the range is from 0 to 512 if encryption is disabled the range id form 0 to 124 if encryption is enabled For AUS-BS and AUS-SA with SW version 4.0 and higher the range is between 0 to 8 or 25 (via licensing). For AUS-BS and AUS-SA with SW version below 4.0 the range is between 0 to 5. BWA-PtP products return 65535.
INT bwaVLMaxNumOfAssociationsLimit	1.3.6.1.4.1.12394.1.1.6.19	INTEGER	read-only	Applicable to AU only. Not applicable to BWA-PtP products. Shows the limit for the number of SUs that can be associated with the AU. For AU-BS, AU-SA if Data Encryption is enabled, the upper limit is 124, otherwise it is 512. For AUS-BS, AUS-SA with SW version 4.0 and higher the upper limit is 8 or 25 (via licensing). For AUS-BS, AUS-SA with SW version below 4.0 the upper limit is 5. BWA-PtP products return 65535.
INT bwaVLMaxTxApplicableModulationLevel	1.3.6.1.4.1.12394.1.1.6.6.1.2	INTEGER	read-only	Applicable to SU/RB only. The applicable modulation level for an entry in the Maximum Transmit Power Table. Level 8 is not applicable to units with HW revision A.
STR bwaVLMaxTxPower	1.3.6.1.4.1.12394.1.1.6.6.1.4	DisplayString	read-write	Applicable to SU/RB only. Read-only for units with SW version 4.0 and higher. The maximum value that can be configured for the bwaVLTxPower parameter. This is also the maximum power level that can be reached by the ATPC algorithm. The range is -10 dBm to the maximum value defined by bwaVLDefinedMaximumTxPowerRange for the applicable modulation level.
INT bwaVLMeasuredCellDistance	1.3.6.1.4.1.12394.1.1.6.15.3	INTEGER	read-only	Applicable AU/BU only. The Maximum Cell Distance as calculated by the AU/BU. Range: 0 to 54 (Kilometers).
INT bwaVLMeasureUpLinkQualityIndicator	1.3.6.1.4.1.12394.1.1.11.6.1	INTEGER	read-write	Applicable to SU/RB. Starts calculation of LQI. The calculation will be for a period of 10 seconds.
bwaVLMib	1.3.6.1.4.1.12394.1.1			BWA VL products, BWA 4900, BWA-PtP
INT bwaVLMinContentionWindow	1.3.6.1.4.1.12394.1.1.10.3	INTEGER	read-write	Applicable to SU and AU. For units bearing SW version 4.0 and above applicable to BWA PtP products, for previous SW versions not applicable to BWA PtP products. The initial value to be used by the contention window calculation algorithm. Value must be 0 or power of 2 minus 1 (7,15,31...). Range: 0 to 1023, excluding 1 and 3. BWA-PtP products with SW version below 4.0 return 65535.
INT bwaVLMinimumHwRevision	1.3.6.1.4.1.12394.1.1.1.18.2.1.11	INTEGER	read-only	Applicable to all units. The Minimum HW Revision needed to support the country code.
INT bwaVLMinimumIntervalBetweenATPCMessages	1.3.6.1.4.1.12394.1.1.6.13.4	INTEGER	read-write	Applicable AU/BU only. The minimum interval between two consecutive AU/BU to SU/RB messages. Range: 1 to 3600 (Sec).
INT bwaVLMinimumSNRLevel	1.3.6.1.4.1.12394.1.1.6.13.3	INTEGER	read-write	Applicable AU/BU only. Defines the minimum desired level of the average SNR at the AU/BU. Below this level, if AtpcOption is enabled, the AU/BU will transmit ATPC Power-Up messages to the applicable SU/RB. The MinimumSNRLevel cannot be higher than *MaximumSNRLevel. Range: 4 to 60 (dB).
INT bwaVLMinIntervalBetweenAdaptiveModulationAlgorithmMessages	1.3.6.1.4.1.12394.1.1.10.9.4	INTEGER	read-write	Applicable all units. The minimum interval between two consecutive AU/BU to SU/RB messages. Range: 1 to 3600 (Sec).
INT bwaVLMinModulationLevel	1.3.6.1.4.1.12394.1.1.1.18.2.1.6	INTEGER	read-only	Applicable to all units. The minimum supported modulation level.
INT bwaVLMirDownlink	1.3.6.1.4.1.12394.1.1.7.2	INTEGER	read-write	Applicable to SU/RB only. The Maximum Information Rate (MIR) from AU/BU to SU/RB. MIR must be above bwaVLCirDownlink value. Range for set: 128 to 2,048 (Kbps) for SU-3 with SW version below 4.0, 128 to 3,072 (Kbps) for SU-3 with SW version 4.0 and higher, 128 to 3,968 (Kbps) for SU-6 with SW version less than 4.0, 128 to 6,016 (Kbps) for SU-6 with SW version greater than 4.0, 128 to 14,976 (Kbps) for SU-24, 128 to 53,888 (Kbps) for SU-BD and SU-54, 128 to 6,912 (Kbps) for RB-14, 128 to 22,016 (Kbps) for RB-28, 128 to 107,904 (Kbps) for RB-100. 128 to 6,016 (Kbps) for SU-I. The actual value (Get) will be the entered value rounded to the nearest multiple of 128 (N*128).
INT bwaVLMirOnlyOption	1.3.6.1.4.1.12394.1.1.7.9	INTEGER	read-write	Applicable to AU only. Not applicable to BWA-PtP products. When bwaMirOnly is enabled, it overrides the CIR/MIR algorithm for determining actual information rate and forces the algorithm to operate with MIR parameter settings only. When enabled, the Graceful Degradation algorithm is disabled.
INT bwaVLMIRThresholdPercent	1.3.6.1.4.1.12394.1.1.7.14	INTEGER	read-write	Applicable to AU only. MIR Threshold Percent
INT bwaVLMirUplink	1.3.6.1.4.1.12394.1.1.7.3	INTEGER	read-write	Applicable to SU/RB only. The Maximum Information Rate (MIR) from SU/RB to AU/BU. MIR must be above bwaVLCirUplink value. Range for set: 128 to 2,048 (Kbps) for SU-3, 128 to 3,968 (Kbps) for SU-6 with SW version less than 4.0, 128 to 4,096 (Kbps) for SU-6 with SW version greater than 4.0, 128 to 14,976 (Kbps) for SU-24, 128 to 53,888 (Kbps) for SU-BD and SU-54, 128 to 6,912 (Kbps) for RB-14, 128 to 22,016 (Kbps) for RB-28, 128 to 107,904 (Kbps) for RB-100. 128 to 2,048 (Kbps) for SU-I. The actual value (Get) will be the entered value rounded to the nearest multiple of 128 (N*128).
IP bwaVLMngIpRangeEnd	1.3.6.1.4.1.12394.1.1.3.10.1.4	IpAddress	read-write	Applicable to all units. End Address of the range. Used only if bwaVLMngIpRangeFlag is rangeDefinedByStartEndAddr
bwaVLMngIpRangeEntry	1.3.6.1.4.1.12394.1.1.3.10.1		not-accessible	Applicable to all units. A Management IP Address Ranges Table entry
INT bwaVLMngIpRangeFlag	1.3.6.1.4.1.12394.1.1.3.10.1.2	INTEGER	read-write	Applicable to all units. Defines the method of defining the range: Using Start & End Address( rangeDefinedByStartEndAddr ), or using Start Address and Mask ( rangeDefinedByStartAddrSubNetMask ).
INT bwaVLMngIpRangeIdx	1.3.6.1.4.1.12394.1.1.3.10.1.1	INTEGER	read-only	Applicable to all units. Index of an entry in the Management IP Address Ranges Table
IP bwaVLMngIpRangeMask	1.3.6.1.4.1.12394.1.1.3.10.1.5	IpAddress	read-write	Applicable to all units. End Address of the range. Used only if bwaVLMngIpRangeFlag is rangeDefinedByStartAddrMask
bwaVLMngIpRangesTable	1.3.6.1.4.1.12394.1.1.3.10		not-accessible	Applicable to all units. Table of Management IP Address Ranges
IP bwaVLMngIpRangeStart	1.3.6.1.4.1.12394.1.1.3.10.1.3	IpAddress	read-write	Applicable to all units. Start Address of the range
INT bwaVLMulticastModulationLevel	1.3.6.1.4.1.12394.1.1.10.6	INTEGER	read-write	Applicable to AU/BU only. The modulation level for multicast and broadcast data frames. The range is 1 to 8. 8 is not applicable for units with HW revision A.
INT bwaVLNeighborAuAdapModOption	1.3.6.1.4.1.12394.1.1.6.11.4.1.11	INTEGER	read-only	Applicable to SU/RB only. Neighbor AU/BU adaptive modulation option configuration in the Neighbor AU/BU Table.
INT bwaVLNeighborAuAssocLoadStatus	1.3.6.1.4.1.12394.1.1.6.11.4.1.5	INTEGER	read-only	Applicable to SU/RB only. Neighbor AU/BU association load status in the Neighbor AU/BU Table.
INT bwaVLNeighborAuAtpcOption	1.3.6.1.4.1.12394.1.1.6.11.4.1.10	INTEGER	read-only	Applicable to SU/RB only. Neighbor AU/BU ATPC option configuration in the Neighbor AU/BU Table.
INT bwaVLNeighborAuAuthOption	1.3.6.1.4.1.12394.1.1.6.11.4.1.19	INTEGER	read-only	Applicable to SU/RB only. Neighbor AU/BU authentication option configuration in the Neighbor AU/BU Table.
INT bwaVLNeighborAuBurstModeOption	1.3.6.1.4.1.12394.1.1.6.11.4.1.12	INTEGER	read-only	Applicable to SU/RB only. Neighbor AU/BU burst mode option configuration in the Neighbor AU/BU Table.
INT bwaVLNeighborAuConcatenationOption	1.3.6.1.4.1.12394.1.1.6.11.4.1.15	INTEGER	read-only	Applicable to SU/RB only. Neighbor AU/BU concatenation option configuration in the Neighbor AU/BU Table.
INT bwaVLNeighborAuCountryCode	1.3.6.1.4.1.12394.1.1.6.11.4.1.8	INTEGER	read-only	Applicable to SU/RB only. Neighbor AU/BU supported country code in the Neighbor AU/BU Table.
INT bwaVLNeighborAuDataEncyptOption	1.3.6.1.4.1.12394.1.1.6.11.4.1.20	INTEGER	read-only	Applicable to SU/RB only. Neighbor AU/BU data encryption option configuration in the Neighbor AU/BU Table.
INT bwaVLNeighborAuDfsOption	1.3.6.1.4.1.12394.1.1.6.11.4.1.14	INTEGER	read-only	Applicable to SU/RB only. Neighbor AU/BU DFS option configuration in the Neighbor AU/BU Table.
bwaVLNeighborAuEntry	1.3.6.1.4.1.12394.1.1.6.11.4.1		not-accessible	Applicable to SU/RB only. An entry in the Neighbor AU/BU Table.
STR bwaVLNeighborAuESSID	1.3.6.1.4.1.12394.1.1.6.11.4.1.3	DisplayString	read-only	Applicable to SU/RB only. The ESSID of an AU/BU in the Neighbor AU/BU Table. Accessible only with SNMP Write Community.
INT bwaVLNeighborAuHwRevision	1.3.6.1.4.1.12394.1.1.6.11.4.1.7	INTEGER	read-only	Applicable to SU/RB only. Neighbor AU/BU HW revision in the Neighbor AU/BU Table.
INT bwaVLNeighborAuIdx	1.3.6.1.4.1.12394.1.1.6.11.4.1.1	INTEGER	read-only	Applicable to SU/RB only. An index of an entry in the Neighbor AU/BU Table.
INT bwaVLNeighborAuLearnCountryCodeBySU	1.3.6.1.4.1.12394.1.1.6.11.4.1.17	INTEGER	read-only	Applicable to SU only. Starting with 4.0 is not applicable for BWA 4900 and BWA PtP products. Neighbor AU Learn Country Code by SU configuration in the Neighbor AU Table.
MAC bwaVLNeighborAuMacAdd	1.3.6.1.4.1.12394.1.1.6.11.4.1.2	MacAddress	read-only	Applicable to SU/RB only. A MAC address of an AU/BU in the Neighbor AU/BU Table.
INT bwaVLNeighborAuMark	1.3.6.1.4.1.12394.1.1.6.11.4.1.6	INTEGER	read-only	Applicable to SU/RB only. Neighbor AU/BU mark in the Neighbor AU/BU Table.
INT bwaVLNeighborAuPerSuDistanceLearning	1.3.6.1.4.1.12394.1.1.6.11.4.1.21	INTEGER	read-only	Applicable to SU only. Neighbor AU per SU distance learning option configuration in the Neighbor AU Table.
INT bwaVLNeighborAuSecurityMode	1.3.6.1.4.1.12394.1.1.6.11.4.1.18	INTEGER	read-only	Applicable to SU/RB only. Neighbor AU/BU security mode configuration in the Neighbor AU/BU Table.
INT bwaVLNeighborAuSNR	1.3.6.1.4.1.12394.1.1.6.11.4.1.4	INTEGER	read-only	Applicable to SU/RB only. The received signal quality (SNR) in dB of an AU/BU in the Neighbor AU/BU Table.
STR bwaVLNeighborAuSwVer	1.3.6.1.4.1.12394.1.1.6.11.4.1.9	DisplayString	read-only	Applicable to SU/RB only. Neighbor AU/BU SW version in the Neighbor AU/BU Table.
bwaVLNeighborAuTable	1.3.6.1.4.1.12394.1.1.6.11.4		not-accessible	Applicable to SU/RB only. A table of data on neighboring AUs/BUs.
INT bwaVLNewUnitTypeTrap	1.3.6.1.4.1.12394.1.1.14.16	INTEGER	read-only	Applicable to BU/RB only. The new type of the BWA PtP unit.
C32 bwaVLNoOfDuplicateFramesDiscarded	1.3.6.1.4.1.12394.1.1.11.2.3.8	Counter32	read-only	Applicable to all units. The number of frames discarded due to receiving multiple copies.
C32 bwaVLNoOfInternallyDiscardedMirCir	1.3.6.1.4.1.12394.1.1.11.2.3.9	Counter32	read-only	Applicable to all units. The number of data frames received from the Ethernet port that were discarded by the MIR/CIR mechanism either to avoid exceeding the maximum allowed information rate, or when the wireless link conditions do not enable reaching the allowed rate.
INT bwaVLNumberOfMacAddressesInDenyList	1.3.6.1.4.1.12394.1.1.5.10.4	INTEGER	read-only	Applicable to AU only. Not applicable to BWA-PtP units. Number of MAC addresses in the MAC Address Deny List Table.
INT bwaVLNumOfAssociationsSinceLastReset	1.3.6.1.4.1.12394.1.1.1.11	INTEGER	read-only	Applicable to all units. The number of associations since last reset, including duplicate associations (re-associations).
INT bwaVLNumOfSoftwareRetries	1.3.6.1.4.1.12394.1.1.10.9.3	INTEGER	read-write	Applicable to all units. Read-only for units with version 2.0. Not applicable for units with SW version 3.0 and higher. The maximum number of times to use the Software Retry mechanism when it is enabled.
INT bwaVLNwMngFilter	1.3.6.1.4.1.12394.1.1.3.2	INTEGER	read-write	Applicable to all units. Disables or enable on one of the ports, or on both ports, IP address based filtering of management messages (e.g. SNMP , Telnet , TFTP , DHCP).
IP bwaVLNwMngIpAddress	1.3.6.1.4.1.12394.1.1.3.3.1.1	IpAddress	read-write	Applicable to all units. An IP address in the Management IP Filter Table.
INT bwaVLNwMngIpTableIdx	1.3.6.1.4.1.12394.1.1.3.3.1.2	INTEGER	read-only	Applicable to all units. A table index for an entry in the Management IP Filter Table.
bwaVLNwMngParameters	1.3.6.1.4.1.12394.1.1.3
IP bwaVLNwMngTrapAddress	1.3.6.1.4.1.12394.1.1.3.7.1.2	IpAddress	read-write	Applicable to all units. An IP address in the Management Trap Table entry.
STR bwaVLNwMngTrapCommunity	1.3.6.1.4.1.12394.1.1.3.7.1.1	DisplayString	read-write	Applicable to all units. The trap community associated with the applicable entry in the Management Trap Table. Up to 14 printable case sensitive ASCII characters.
INT bwaVLNwTrapTableIdx	1.3.6.1.4.1.12394.1.1.3.7.1.3	INTEGER	read-only	Applicable to all units. Tables Index for an entry in the Management Trap Table.
bwaVLOID	1.3.6.1.4.1.12394.4.1
STR bwaVLOperatorDefaultsFileName	1.3.6.1.4.1.12394.1.1.2.10.3.2	DisplayString	read-write	Applicable to all units. The name of the Operator Defaults file to be downloaded/uploaded
STR bwaVLOperatorESSID	1.3.6.1.4.1.12394.1.1.6.1.3	DisplayString	read-write	Applicable to AU/BU only. A secondary ESSID to support easy installation of SUs as well as the use of the Best AU/BU feature. Accessible only with SNMP Write Community Up to 31 printable case sensitive ASCII characters.
INT bwaVLOperatorESSIDOption	1.3.6.1.4.1.12394.1.1.6.1.2	INTEGER	read-write	Applicable to AU/BU only. Enabling/disabling the use of the Operator ESSID.
C32 bwaVLOthersTxEvents	1.3.6.1.4.1.12394.1.1.11.2.4.1.4	Counter32	read-only	Applicable to all units. The number of Tx events due to problems other than those of the other Tx Events counters.
C32 bwaVLOverrunEvents	1.3.6.1.4.1.12394.1.1.11.2.4.2.3	Counter32	read-only	Applicable to all units. The number of frames that were discarded because the receive rate exceeded the processing capability or the capacity of the Ethernet port.
NTF bwaVLParameterChangedTRAP	1.3.6.1.4.1.12394.4.1.3.103			Applicable to all units. A trap indicating a change in a CIR/MIR, IP Filter or VLAN parameter.
bwaVLPerformanceParams	1.3.6.1.4.1.12394.1.1.10
bwaVLPerModulationLevelCounters	1.3.6.1.4.1.12394.1.1.11.2.5
INT bwaVLPerSuDistanceLearning	1.3.6.1.4.1.12394.1.1.6.15.5	INTEGER	read-write	Aplicable to AU only. Applicable only if Cell Distance Mode is set to Automatic. When disabled, all SUs in the cell will use for the ACK Timeout the computed distance of the farthest SU. When enabled, each SU will use its own computed distance
C32 bwaVLPhyErrors	1.3.6.1.4.1.12394.1.1.11.2.4.2.1	Counter32	read-only	Applicable to all units, only when DFS is enabled. The number of unidentified signals.
bwaVLPortsControl	1.3.6.1.4.1.12394.1.1.5.11
INT bwaVLPowerLevelSteps	1.3.6.1.4.1.12394.1.1.6.13.6	INTEGER	read-write	Applicable AU/BU only. The step in dB that the SU/RB will use when receiving an ATPC Power-Up/Power-Down message. Range: 1 to 20 (dB).
NTF bwaVLPowerUpFromReset	1.3.6.1.4.1.12394.4.1.3.101			An AU/BU trap indicating power up after Reset.
INT bwaVLPPPoEBroadcastOverrideFilter	1.3.6.1.4.1.12394.1.1.5.7.2	INTEGER	read-write	Applicable to SU/RB only. Enables or disables the broadcasting of PPPoE messages, overriding the general *bwaVLEthBroadcastFiltering Ethernet broadcast filtering option.
MAC bwaVLPreferredAuMacAddress	1.3.6.1.4.1.12394.1.1.6.11.3	MacAddress	read-write	Applicable to SU/RB only. The MAC address of the preferred AU/BU (overriding the Best AU/BU selection process). 000000000000 means no preferred AU/BU.
bwaVLProducts	1.3.6.1.4.1.12394.4.1.3
NTF bwaVLPromiscuousModeTRAP	1.3.6.1.4.1.12394.4.1.3.105			An AU/BU trap, indicating that the AU/BU In (On) Promiscuous Mode or out (Off) Promiscuous Mode.
INT bwaVLQinQEthertype	1.3.6.1.4.1.12394.1.1.5.1.7.1	INTEGER	read-write	Applicable to AU and SU. Not applicable to PtP units. The Ethernet type of the Service Provider Tag. The range is 0x8101(33025) - 0x9000(36864), 0x9100(37120), 0x9200(37376).
INT bwaVLQinQProviderVlanID	1.3.6.1.4.1.12394.1.1.5.1.7.2	INTEGER	read-write	Applicable to SU only. VLAN ID of the Service Provider Tag.
INT bwaVLRadioBand	1.3.6.1.4.1.12394.1.1.1.15	INTEGER	read-only	Applicable to all units. The unit's radio band.
STR bwaVLReadOnlyPassword	1.3.6.1.4.1.12394.1.1.2.8.1	DisplayString	read-write	Applicable to all units. The User (read only) password. This is also the Read Community String. Up to 8 printable ASCII characters.
INT bwaVLReadUpLinkQualityIndicator	1.3.6.1.4.1.12394.1.1.11.6.2	INTEGER	read-only	Applicable to SU/RB. The results of the last LQI calculation. Range: 1 to 8.
C32 bwaVLRecievedBadFrames	1.3.6.1.4.1.12394.1.1.11.2.3.7	Counter32	read-only	Applicable to all units. The number of frames received from the wireless media with errors (CRC errors).
INT bwaVLRegulationMaxEIRP	1.3.6.1.4.1.12394.1.1.1.18.2.1.5	INTEGER	read-only	Applicable to all units. The maximum Tx EIRP when using the applicable sub-band. A Regulation Max EIRP of 0, means no limit.
INT bwaVLRegulationMaxTxPowerAtAntennaPort	1.3.6.1.4.1.12394.1.1.1.18.2.1.4	INTEGER	read-only	Applicable to all units. The maximum allowed Tx power when using the applicable sub-band. A RegulationMaxTxPowerAtAntennaPort of 255, means no limit
INT bwaVLResetPerModulationLevelCounters	1.3.6.1.4.1.12394.1.1.11.2.5.1	INTEGER	read-write	Applicable to all units. Resets the per-Modulation Level counters .
INT bwaVLResetSpectrumCounters	1.3.6.1.4.1.12394.1.1.6.18.6	INTEGER	read-write	Applicable to all units. Resets the spectrum analysis counters.
INT bwaVLResetTrafficCounters	1.3.6.1.4.1.12394.1.1.11.2.1	INTEGER	read-write	Applicable to all units. Resets the traffic counters.
INT bwaVLResetUnit	1.3.6.1.4.1.12394.1.1.2.1	INTEGER	read-write	Applicable to all units. Resets the unit and applies new parameter values.
INT bwaVLRoamingOption	1.3.6.1.4.1.12394.1.1.5.9	INTEGER	read-write	Applicable to SU/RB only. Disable/enable the roaming feature. When enabled, the SU/RB will start scanning for an AU/BU after about one second of not receiving beacons or data from current AU/BU. Once it found a new AU/BU, it will also send through the wireless network a roaming SNAP on behalf of its clients informing other devices in the network of their new location. When disabled, it will wait for about seven seconds before starting scanning, and it will not send a roaming SNAP.
INT bwaVLRTSThreshold	1.3.6.1.4.1.12394.1.1.10.1	INTEGER	read-write	Applicable to SU and AU. Not applicable to BWA-PtP products. The minimum frame size that requires an RTS/CTS handshake. Range: For units bearing SW version 3.0 and above: 20 to 3400 bytes, for previous SW versions 20 to 1600 bytes. BWA-PtP products return 65535.
INT bwaVLRunningFrom	1.3.6.1.4.1.12394.1.1.1.3	INTEGER	read-only	Applicable to all units. The memory (main or shadow) from which the current version is running from.
STR bwaVLRunningSoftwareVersion	1.3.6.1.4.1.12394.1.1.1.2	DisplayString	read-only	Applicable to all units. Running software version.
IP bwaVLRunTimeDefaultIPGateway	1.3.6.1.4.1.12394.1.1.4.8	IpAddress	read-only	Applicable to all units. The run-time Gateway IP address. If DHCP is used the Run Time Gateway IP Address is the address given to the unit by the server. Otherwise it is the manually configured address.
STR bwaVLRunTimeESSID	1.3.6.1.4.1.12394.1.1.6.1.4	DisplayString	read-only	Applicable to SU/RB only. The ESSID of the associated AU/BU. Accessible only with SNMP Write Community. Up to 31 printable ASCII characters, case sensitive.
IP bwaVLRunTimeIPaddr	1.3.6.1.4.1.12394.1.1.4.6	IpAddress	read-only	Applicable to all units. The run-time IP address. If DHCP is used the Run Time IP Address is the address given to the unit by the server. Otherwise it is the manually configured address.
IP bwaVLRunTimeSubNetMask	1.3.6.1.4.1.12394.1.1.4.7	IpAddress	read-only	Applicable to all units. The run-time Subnet Mask. If DHCP is used the Run Time Subnet Mask is the mask given to the unit by the server. Otherwise it is the manually configured mask.
C32 bwaVLRxDecryptEvents	1.3.6.1.4.1.12394.1.1.11.2.4.2.4	Counter32	read-only	Applicable to all units. The number of frames that were not received properly due to a problem in the data decryption mechanism.
bwaVLRxEvents	1.3.6.1.4.1.12394.1.1.11.2.4.2
INT bwaVLSaveCurrentConfigurationAsOperatorDefaults	1.3.6.1.4.1.12394.1.1.2.6	INTEGER	read-write	Applicable to all units. Saves the current configuration as Operator Defaults. Cannot be executed after requesting set defaults and the unit was not reset.
INT bwaVLScanningMode	1.3.6.1.4.1.12394.1.1.6.16	INTEGER	read-write	Applicable to SU/RB only. The scanning mode. In cells where the DFS Option is enabled Scanning Mode is forced to Passive.
INT bwaVLScanningStep	1.3.6.1.4.1.12394.1.1.6.12.3	INTEGER	read-write	Applicable to all units - For flexible Sub-Bands only. For units with version 2.0 and above this is a read-only parameter. The scanning step to be used for generating the frequency subset.
INT bwaVLSecurityMode	1.3.6.1.4.1.12394.1.1.9.5	INTEGER	read-write	Applicable to all units. The fips197 option is applicable only to units with a license to use FIPS 197 algorithm. The encryption algorithm to be used for authentication messages and/or data encryption.
INT bwaVLSecurityModeSupport	1.3.6.1.4.1.12394.1.1.9.12	INTEGER	read-only	Applicable to all units. Returns types of encryption that are supported. 0 - no encryption 1 - WEP 2 - AES OCB 3 - WEP and AES OCB 4 - FIPS-197 5 - FIPS-197 and WEP 6 - FIPS-197 and AES OCB 7 - FIPS-197, AES OCB and WEP
bwaVLSecurityParameters	1.3.6.1.4.1.12394.1.1.9
INT bwaVLSelectSubBandIndex	1.3.6.1.4.1.12394.1.1.6.12.10.1	INTEGER	read-write	Applicable to all units with SW version below 4.0 For units with SW version 4.0 and up it is applicable only for AU/BU. For SU/RB it defines only the sub-band for the Spectrum Analyzer. The ID of the sub-band used by the unit.
STR bwaVLSerialNumber	1.3.6.1.4.1.12394.1.1.1.21	DisplayString	read-only	Applicable to all units. Serial Number of the unit
bwaVLServiceParameters	1.3.6.1.4.1.12394.1.1.7
INT bwaVLSetDefaults	1.3.6.1.4.1.12394.1.1.2.2	INTEGER	read-write	Applicable to all units. Sets unit configuration to Defaults values after the next reset. noDefaultSettingRequested : Read-Only Option, no Default setting was Issued. completeFactory : All parameters revert to Factory Defaults values. partialFactory : All parameters revert to Factory Defaults values, except the parameters required for maintaining wireless connectivity. completeOperator: All parameters revert to Operator Defaults values. partialOperator : All parameters revert to Operator Defaults values, except the parameters required for maintaining wireless connectivity. cancelCurrentPendingRequest : Default Setting request is cancelled.
INT bwaVLSetSelectedFreqSubset	1.3.6.1.4.1.12394.1.1.6.12.5	INTEGER	read-write	Applicable to SU/RB and to AU/BU. Not applicable to SU/RB with SW version 4.0 and higher. Apply the selected subset. After the next reset the new subset will be used.
STR bwaVLShadowVersionFileName	1.3.6.1.4.1.12394.1.1.1.7	DisplayString	read-only	Applicable to all units. Shadow software version file name.
STR bwaVLShadowVersionNumber	1.3.6.1.4.1.12394.1.1.1.6	DisplayString	read-only	Applicable to all units. Shadow software version number.
bwaVLSiteSurvey	1.3.6.1.4.1.12394.1.1.11
INT bwaVLSoftwareRetrySupport	1.3.6.1.4.1.12394.1.1.10.9.2	INTEGER	read-write	Applicable to all units. Read-only for units with version 2.0. Not applicable for units with SW version 3.0 and higher. The status of the Software Retry mechanism. Enabled when the Adaptive Modulation algorithm is enabled and the Burst Mode Option is disabled. Otherwise it is disabled.
INT bwaVLSpectrumAnalysisActivation	1.3.6.1.4.1.12394.1.1.6.18.4	INTEGER	read-write	Applicable to all units. Activates spectrum analysis, the unit is automatically reset upon activation.
INT bwaVLSpectrumAnalysisChannelScanPeriod	1.3.6.1.4.1.12394.1.1.6.18.1	INTEGER	read-write	Applicable to all units. The period of staying on each channel for information gathering when performing Spectrum analysis. Range: 2-30 seconds.
STR bwaVLSpectrumAnalysisInformationChannel	1.3.6.1.4.1.12394.1.1.6.18.7.1.2	DisplayString	read-only	Applicable to all units. The channels in the Spectrum Analysis Information Table. If the unit is currently under spectrum analysis the channels would be those on which the analysis is currently performed. If the unit is in normal mode the channels would be the those on which the last analysis was performed.
bwaVLSpectrumAnalysisInformationEntry	1.3.6.1.4.1.12394.1.1.6.18.7.1		not-accessible	Applicable to all units. The spectrum analysis information table entry.
INT bwaVLSpectrumAnalysisInformationOFDMFrames	1.3.6.1.4.1.12394.1.1.6.18.7.1.6	INTEGER	read-only	Applicable to all units. The number of OFDM frames detected in the channel. If the unit is currently under spectrum analysis the count would be of the analysis that is currently performed. If the unit is in normal mode the count would be of the last analysis performed.
INT bwaVLSpectrumAnalysisInformationSignalCount	1.3.6.1.4.1.12394.1.1.6.18.7.1.3	INTEGER	read-only	Applicable to all units. The number of signals (excluding OFDM frames) detected in the channel. If the unit is currently under spectrum analysis the count would be of the analysis that is currently performed. If the unit is in normal mode the count would be of the last analysis performed.
INT bwaVLSpectrumAnalysisInformationSignalSNR	1.3.6.1.4.1.12394.1.1.6.18.7.1.4	INTEGER	read-only	Applicable to all units. The approximate SNR of the signals (excluding OFDM frames) detected in the channel. If the unit is currently under spectrum analysis the SNR would be of the analysis that is currently performed. If the unit is in normal mode the SNR would be of the last analysis performed.
INT bwaVLSpectrumAnalysisInformationSignalWidth	1.3.6.1.4.1.12394.1.1.6.18.7.1.5	INTEGER	read-only	Applicable to all units. The average width of the signals (excluding OFDM frames) detected in the channel. If the unit is currently under spectrum analysis the width would be of the analysis that is currently performed. If the unit is in normal mode the width would be of the last analysis performed.
bwaVLSpectrumAnalysisInformationTable	1.3.6.1.4.1.12394.1.1.6.18.7		not-accessible	Applicable to all units. The spectrum analysis information table.
INT bwaVLSpectrumAnalysisInformationTableIdx	1.3.6.1.4.1.12394.1.1.6.18.7.1.1	INTEGER	read-only	Applicable to all units. A read only table index for a Spectrum Analysis Information entry in the Spectrum Analysis Information Table.
bwaVLSpectrumAnalysisParameters	1.3.6.1.4.1.12394.1.1.6.18
INT bwaVLSpectrumAnalysisScanCycles	1.3.6.1.4.1.12394.1.1.6.18.2	INTEGER	read-write	Applicable to all units. The number of scanning cycles when performing Spectrum Analysis. Range: 1-100.
INT bwaVLSpectrumAnalysisStatus	1.3.6.1.4.1.12394.1.1.6.18.5	INTEGER	read-only	Applicable to all units. Defines weather the unit is currently under performing a spectrum analysis process.
bwaVLSU	1.3.6.1.4.1.12394.4.1.2
bwaVLSU_24_BD	1.3.6.1.4.1.12394.4.1.13
bwaVLSU_3_1D	1.3.6.1.4.1.12394.4.1.16
bwaVLSU_3_4D	1.3.6.1.4.1.12394.4.1.17
bwaVLSU_54_BD	1.3.6.1.4.1.12394.4.1.15
bwaVLSU_6_1D	1.3.6.1.4.1.12394.4.1.11
bwaVLSU_6_BD	1.3.6.1.4.1.12394.4.1.12
bwaVLSU_BD	1.3.6.1.4.1.12394.4.1.14
bwaVLSU_I	1.3.6.1.4.1.12394.4.1.18
NTF bwaVLSUassociatedAUTRAP	1.3.6.1.4.1.12394.4.1.3.2			An AU/BU trap indicating a new association with an SU/RB.
NTF bwaVLSUassociatedTRAP	1.3.6.1.4.1.12394.4.1.3.6			An SU/RB trap indicating association with an AU/BU. In addition to the MAC address information of the AU/BU, the trap also includes information on the average SNR of frames received from the AU/BU.
INT bwaVLSubBandLowerFrequency	1.3.6.1.4.1.12394.1.1.6.12.1	INTEGER	read-write	Applicable to SU only. Not applicable to units with SW version 2.0 or higher. The lowest frequency in the subset to be used for scanning. For 5.8GHz products the range is 5740 to 5830 MHz using 10MHz resolution. For 4.9GHz products the range is 4920 to 5080 MHz using 10MHz resolution. For HW Revision C and above this leaf is not relevant - shall return 0.
bwaVLSubBandSelect	1.3.6.1.4.1.12394.1.1.6.12.10
INT bwaVLSubBandUpperFrequency	1.3.6.1.4.1.12394.1.1.6.12.2	INTEGER	read-write	Applicable to SU only. Not applicable to units with SW version 2.0 or higher. The highest frequency in the subset to be used for scanning. For 5.8GHz products the range is 5740 to 5830 MHz using 10MHz resolution. For 4.9GHz products the range is 4920 to 5080 MHz using 10MHz resolution. For HW Revision C and above this leaf is not relevant - shall return 0.
IP bwaVLSubNetMask	1.3.6.1.4.1.12394.1.1.4.2	IpAddress	read-write	Applicable to all units. Subnet mask of the unit.
INT bwaVLSUBurstDurationHighPriority	1.3.6.1.4.1.12394.1.1.7.10.4.7	INTEGER	read-write	Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum duration of burst that can be done by SU/RB with High Priority packets. The parameter is configurable in AU and the SUs/RB will learn it form AU/BU. The time is given in 250 microseconds units
INT bwaVLSUBurstDurationLowPriority	1.3.6.1.4.1.12394.1.1.7.10.4.8	INTEGER	read-write	Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Applicable only if the Wireless Link Prioritization Option is enabled. Defines the Maximum duration of burst that can be done by SU/RB with High Priority packets. The parameter is configurable in AU/BU and the SUs/RB will learn it from AU/BU. The time is given in 250 microseconds units
INT bwaVLSUDefaultKeyID	1.3.6.1.4.1.12394.1.1.9.2	INTEGER	read-write	Applicable to SU/RB only. The key to be used for encryption of authentication messages and/or data. Range: 1 to 4.
INT bwaVLSUPerModulationLevelCountersApplicableModLevel	1.3.6.1.4.1.12394.1.1.11.2.5.2.1.2	INTEGER	read-only	Applicable to SU/RB. The applicable modulation level of the entry in the Per modulation level Counters table. Modulation Level 8 is not applicable for units with HW revision A.
bwaVLSUPerModulationLevelCountersEntry	1.3.6.1.4.1.12394.1.1.11.2.5.2.1		not-accessible	Applicable to SU/RB. An entry in the Per modulation Counters table.
bwaVLSUPerModulationLevelCountersTable	1.3.6.1.4.1.12394.1.1.11.2.5.2		not-accessible	Applicable to SU/RB. Per Rate Counters table.
INT bwaVLSUPerModulationLevelCountersTableIdx	1.3.6.1.4.1.12394.1.1.11.2.5.2.1.1	INTEGER	read-only	Applicable to SU/RB. An index of an entry in the Per modulation level Counters table.
C32 bwaVLSUPerModulationLevelCountersTxFailed	1.3.6.1.4.1.12394.1.1.11.2.5.2.1.4	Counter32	read-only	Applicable to SU/RB. The total number of dropped frames at the applicable Modulation Level.
C32 bwaVLSUPerModulationLevelCountersTxSuccess	1.3.6.1.4.1.12394.1.1.11.2.5.2.1.3	Counter32	read-only	Applicable to SU/RB. The total number of successfully transmitted unicasts at the applicable modulation level.
INT bwaVLSUPMirDownlink	1.3.6.1.4.1.12394.1.1.7.13	INTEGER	read-write	Applicable to AU only. The Maximum Information Rate (MIR) from AU to SUP. Range for set: 128 to 12,032 (Kbps). The actual value (Get) will be the entered value rounded to the nearest multiple of 128 (N*128).
bwaVLSysInfo	1.3.6.1.4.1.12394.1.1.1
STR bwaVLSystemLocation	1.3.6.1.4.1.12394.1.1.2.13	DisplayString	read-write	Applicable to all units. The unit location.
INT bwaVLTcpPortPriRTPRTCP	1.3.6.1.4.1.12394.1.1.7.10.3.3.1	INTEGER	read-write	Applicable to all units. RTP/RTCP ports prioritization option for TCP packets. rtpANDrtcp(1): the possible RTP and RTCP packet with destination port in the defined port ranges will get HIGH priority rtpOnly(2): only possible RTP packet (packet with even destination port )
STR bwaVLTcpPortRangeAdd	1.3.6.1.4.1.12394.1.1.7.10.3.3.4	DisplayString	read-write	Applicable to all units. Add port range(s) to TCP Port Ranges Table. Get operation will return the empty string. A range is defined - or where is the Start Port of the range and is the End Port. If only is specified the range is -. The value of and are between 0..65535. The user can add several ranges using comma to separate between ranges. Example: 10-256,99,987-900
bwaVLTcpPortRangeConfig	1.3.6.1.4.1.12394.1.1.7.10.3.3
STR bwaVLTcpPortRangeDelete	1.3.6.1.4.1.12394.1.1.7.10.3.3.5	DisplayString	read-write	Applicable to all units. Delete port range(s) from TCP Port Ranges Table. Get operation will return the empty string. A range is defined - or where is the Start Port of the range and is the End Port. If only is specified the range is -. The value of and are between 0..65535. The user can delete several ranges using comma to separate between ranges. Example: 10-256,99,987-900
INT bwaVLTcpPortRangeDeleteAll	1.3.6.1.4.1.12394.1.1.7.10.3.3.6	INTEGER	read-write	Applicable to all units. Delete all entries form TCP Port Ranges Table Get operation will return 1
INT bwaVLTcpPortRangeEnd	1.3.6.1.4.1.12394.1.1.7.10.3.3.3.1.2	INTEGER	read-only	Applicable to all units. End port of a TCP Port Range
bwaVLTcpPortRangeEntry	1.3.6.1.4.1.12394.1.1.7.10.3.3.3.1		not-accessible	Applicable to all units. A TCP Port Ranges Table entry.
INT bwaVLTcpPortRangeIdx	1.3.6.1.4.1.12394.1.1.7.10.3.3.3.1.3	INTEGER	read-only	Applicable to all units. TCP Port Range Entry's index
INT bwaVLTcpPortRangeNum	1.3.6.1.4.1.12394.1.1.7.10.3.3.2	INTEGER	read-only	Applicable to all units. The number of entries in the TCP Port Range Table
INT bwaVLTcpPortRangeStart	1.3.6.1.4.1.12394.1.1.7.10.3.3.3.1.1	INTEGER	read-only	Applicable to all units. Start port of a TCP Port Range
bwaVLTcpPortRangeTable	1.3.6.1.4.1.12394.1.1.7.10.3.3.3		not-accessible	Table of TCP Port Ranges use for prioritization. The user can define up to 64 ranges. An entry is empty if start is 65535 and end is 0
INT bwaVLTelnetLogoutTimer	1.3.6.1.4.1.12394.1.1.2.5	INTEGER	read-write	Applicable to all units. Time-out of management via Telnet program. Automatic exit if the program is inactive for the defined time. Range: 1 to 999 (minutes).
NTF bwaVLTelnetStatusTRAP	1.3.6.1.4.1.12394.4.1.3.102			Applicable to all units. A trap indicating that a log-in or log-out has been performed via Telnet. Includes the log-in access right and the IP address of the PC performing Telnet.
STR bwaVLTimeSinceLastReset	1.3.6.1.4.1.12394.1.1.1.17	DisplayString	read-only	Applicable to all units. The elapsed time since last reset.
INT bwaVLToSPrecedenceThreshold	1.3.6.1.4.1.12394.1.1.5.8.1	INTEGER	read-write	Applicable to all units. Not applicable to units with SW version 3.1 or higher. Priority threshold (based on the ToS) for frames received from the Ethernet port. Range: 0 to 7.
INT bwaVLToSPrioritizationOption	1.3.6.1.4.1.12394.1.1.7.10.2.1	INTEGER	read-write	Applicable to all units. Disable/Enable IP ToS prioritization and choose the interpretation of the IP ToS field from IP header. ipPrecedence(2): The IP ToS field is defined by RFC791. In this case the prioritization will be done using the Precedence sub-field of IP ToS. This sub-field has 3 bits, so it can be between 0 and 7. dSCP(3): The IP ToS field is defined by RFC2474. In this case the prioritization will be done using the DSCP sub-field. The size of the sub-field is 6 bits, so the range is 0 to 63.
bwaVLToSPriorityParameters	1.3.6.1.4.1.12394.1.1.5.8
C32 bwaVLTotalNoOfDataFramesSubmitted	1.3.6.1.4.1.12394.1.1.11.2.3.5.4	Counter32	read-only	Applicable to all units. The total number of data frames submitted to the internal bridge for transmission to the wireless media.
C32 bwaVLTotalRecievedDataFrames	1.3.6.1.4.1.12394.1.1.11.2.3.6	Counter32	read-only	Applicable to all units. The total number of data frames received from the wireless media, including duplicate frames.
C32 bwaVLTotalRetransmittedFrames	1.3.6.1.4.1.12394.1.1.11.2.3.3	Counter32	read-only	Applicable to all units. The total number of retransmissions of data frames (counts all unsuccessful transmissions/retransmissions).
C32 bwaVLTotalRxConcatenatedFramesDouble	1.3.6.1.4.1.12394.1.1.11.2.3.10	Counter32	read-only	Applicable to all units. The total number of double concatenated frames received from the wireless media, including duplicate frames.
C32 bwaVLTotalRxConcatenatedFramesMore	1.3.6.1.4.1.12394.1.1.11.2.3.12	Counter32	read-only	Applicable to all units. The total number of data fast frames concatenated with more then two frames received from the wireless media, including duplicate frames.
C32 bwaVLTotalRxConcatenatedFramesSingle	1.3.6.1.4.1.12394.1.1.11.2.3.11	Counter32	read-only	Applicable to all units. The total number of data fast frames single concatenated frames received from the wireless media, including duplicate frames.
C32 bwaVLTotalRxEvents	1.3.6.1.4.1.12394.1.1.11.2.4.2.5	Counter32	read-only	Applicable to all units. The total number of Rx special events.
C32 bwaVLTotalRxFramesFromWireless	1.3.6.1.4.1.12394.1.1.11.2.3.2	Counter32	read-only	Applicable to all units. The total number of frames that were received from the wireless media. The count includes data and control and management frames, including beacons received from the AU/BU. The count does not include frames that were discarded internally, bad frames and duplicate frames.
C32 bwaVLTotalRxFramesViaEthernetEx	1.3.6.1.4.1.12394.1.1.11.2.2.1	Counter32	read-only	Applicable to all units. Total number of frames received via the Ethernet port.
C32 bwaVLTotalTransmittedConcatenatedFramesDouble	1.3.6.1.4.1.12394.1.1.11.2.3.1.6	Counter32	read-only	Applicable to all products. The total number of double concatenated frames successfully transmitted to the wireless media, excluding retransmissions.
C32 bwaVLTotalTransmittedConcatenatedFramesMore	1.3.6.1.4.1.12394.1.1.11.2.3.1.8	Counter32	read-only	Applicable to all products. The total number of concatenated frames with more then two frames successfully transmitted to the wireless media, excluding retransmissions.
C32 bwaVLTotalTransmittedConcatenatedFramesSingle	1.3.6.1.4.1.12394.1.1.11.2.3.1.7	Counter32	read-only	Applicable to all products. The total number of double concatenated frames successfully transmitted to the wireless media, excluding retransmissions.
C32 bwaVLTotalTransmittedUnicasts	1.3.6.1.4.1.12394.1.1.11.2.3.1.5	Counter32	read-only	Applicable to AU/BU only. The total number of unicast frames successfully transmitted to the wireless media, excluding retransmissions.
C32 bwaVLTotalTxEvents	1.3.6.1.4.1.12394.1.1.11.2.4.1.5	Counter32	read-only	Applicable to all units. The total number of Tx special events.
C32 bwaVLTotalTxFramesToWireless	1.3.6.1.4.1.12394.1.1.11.2.3.1.4	Counter32	read-only	Applicable to all units. The number of frames transmitted to the wireless media. The count includes one count for each data frame that was transmitted successfully (excluding retransmissions), and also the number of transmitted control and management frames, including beacons.
bwaVLTrafficPriIPToS	1.3.6.1.4.1.12394.1.1.7.10.2
bwaVLTrafficPrioritization	1.3.6.1.4.1.12394.1.1.7.10
bwaVLTrafficPriUdpTcpPortRange	1.3.6.1.4.1.12394.1.1.7.10.3
bwaVLTrafficPriVLAN	1.3.6.1.4.1.12394.1.1.7.10.1
bwaVLTrafficStatistics	1.3.6.1.4.1.12394.1.1.11.2
INT bwaVLTransmitPower	1.3.6.1.4.1.12394.1.1.6.23	INTEGER	read-write	Applicable to all units with SW version 4.0 and higher. The uniform transmit power for all modulation levels. For a specific modulation level the effective transmit power (bwaVLTxPower) is the minimum between the uniform transmit power and the maximum transmit power for that modulation level.
bwaVLTransmitPowerEntry	1.3.6.1.4.1.12394.1.1.6.5.1		not-accessible	Applicable to all units. An entry in the Transmit Power Table.
INT bwaVLTransmitPowerIdx	1.3.6.1.4.1.12394.1.1.6.5.1.1	INTEGER	read-only	Applicable to all units. An index of an entry in the Transmit Power Table.
bwaVLTransmitPowerTable	1.3.6.1.4.1.12394.1.1.6.5		not-accessible	Applicable to all units. A table of transmit power parameters.
INT bwaVLTrapAccessRights	1.3.6.1.4.1.12394.1.1.14.6	INTEGER	read-only	Applicable to all units. The access rights used for login.
INT bwaVLTrapFtpOrTftpStatus	1.3.6.1.4.1.12394.1.1.14.10	INTEGER	read-only	Applicable to all units. The status of the last FTP/TFTP loading procedure.
INT bwaVLTrapLog	1.3.6.1.4.1.12394.1.1.14.7	INTEGER	read-only	Applicable to all units. Login or logout to the Monitor program via Telnet.
MAC bwaVLTrapMACAddress	1.3.6.1.4.1.12394.1.1.14.15	MacAddress	read-only	Applicable to BU/RB only. The MAC address of the BWA PtP unit whose type has been changed
INT bwaVLTrapParameterChanged	1.3.6.1.4.1.12394.1.1.14.5	INTEGER	read-only	Applicable to all units. A modification to one of the parameters related to CIR/MIR, IP Filtering or VLAN.
INT bwaVLTrapRTx	1.3.6.1.4.1.12394.1.1.14.9	INTEGER	read-only	Applicable to AU/BU only. Retransmissions as a percentage of total transmissions.
bwaVLTraps	1.3.6.1.4.1.12394.1.1.14
INT bwaVLTrapSubscriberType	1.3.6.1.4.1.12394.1.1.14.14	INTEGER	read-only	Applicable to AUS only. The type of subscriber that was rejected by AUS
MAC bwaVLTrapSUMacAddr	1.3.6.1.4.1.12394.1.1.14.1	MacAddress	read-only	Applicable to AU/BU only. SU/RB MAC Address.
STR bwaVLTrapSWVersion	1.3.6.1.4.1.12394.1.1.14.17	DisplayString	read-only	The SW version of the SU that tries to associate with a station that has Wireless Link Prioritization Enabled
IP bwaVLTrapTelnetUserIpAddress	1.3.6.1.4.1.12394.1.1.14.8	IpAddress	read-only	Applicable to all units. The IP address of a Telnet user.
STR bwaVLTrapText	1.3.6.1.4.1.12394.1.1.14.3	DisplayString	read-only	Textual string for future use.
INT bwaVLTrapToggle	1.3.6.1.4.1.12394.1.1.14.4	INTEGER	read-only	Applicable to all units. An On/Off toggle status.
INT bwaVLTxControl	1.3.6.1.4.1.12394.1.1.6.21	INTEGER	read-write	Applicable to AU/BU only. Tx Control of the AU/BU. Starting with version 4.0 it is run-time. For SW version below 4.0 the unit reset itself. If set to ethernetStatusControl, the unit will not transmit if the Ethernet link is down. This parameter can be configured only via the ethernet port.
bwaVLTxEvents	1.3.6.1.4.1.12394.1.1.11.2.4.1
bwaVLTxFramesToWireless	1.3.6.1.4.1.12394.1.1.11.2.3.1
STR bwaVLTxPower	1.3.6.1.4.1.12394.1.1.6.5.1.4	DisplayString	read-write	Applicable to all units. Read-only for units with SW version 4.0 and higher. In AU/BU: The transmit power in dBm defined for the applicable rate. In SU/RB: If ATPC is disabled, this is the transmit power in dBm defined for the applicable rate. If ATPC is enabled, it serves as the initial transmit power in dBm for the ATPC algorithm. In SU/RB: The range is -10 dBm to the power value defined by bwaVLMaximumTxPower for the applicable modulation level. In AU/BU: The range is -10 dBm to the power value defined by bwaVLMaximumTxPowerRange for the applicable modulation level.
C32 bwaVLTxWirelessToEthernet	1.3.6.1.4.1.12394.1.1.11.2.2.2	Counter32	read-only	Applicable to all units. Total number of frames transmitted to the Ethernet port.
INT bwaVLUdpPortPriRTPRTCP	1.3.6.1.4.1.12394.1.1.7.10.3.2.1	INTEGER	read-write	Applicale to all units. RTP/RTCP ports prioritization option for UDP packets. rtpANDrtcp(1): the possible RTP and RTCP packet with destination port in the defined port ranges will get HIGH priority rtpOnly(2): only possible RTP packet (packet with even destination port ) with destination port in the defined port ranges will get HIGH priority.
STR bwaVLUdpPortRangeAdd	1.3.6.1.4.1.12394.1.1.7.10.3.2.4	DisplayString	read-write	Applicable to all units. Add port range(s) to UDP Port Ranges Table. Get operation will return the empty string. A range is defined - or where is the Start Port of the range and is the End Port. If only is specified the range is -. The value of and are between 0..65535. The user can add several ranges using a comma to separate between ranges. Example: 10-256,99,987-900
bwaVLUdpPortRangeConfig	1.3.6.1.4.1.12394.1.1.7.10.3.2
STR bwaVLUdpPortRangeDelete	1.3.6.1.4.1.12394.1.1.7.10.3.2.5	DisplayString	read-write	Applicable to all units. Delete port range(s) from UDP Port Ranges Table. Get operation will return the empty string. A range is defined - or where is the Start Port of the range and is the End Port. If only is specified the range is -. The value of and are between 0..65535. The user can delete several ranges using a comma to separate between ranges. Example: 10-256,99,987-900
INT bwaVLUdpPortRangeDeleteAll	1.3.6.1.4.1.12394.1.1.7.10.3.2.6	INTEGER	read-write	Applicable to all units. Delete all entries form UDP Port Ranges Table. Get operation will return 1
INT bwaVLUdpPortRangeEnd	1.3.6.1.4.1.12394.1.1.7.10.3.2.3.1.2	INTEGER	read-only	Applicable to all units. End port of an UDP Port Range
bwaVLUdpPortRangeEntry	1.3.6.1.4.1.12394.1.1.7.10.3.2.3.1		not-accessible	Applicable to all units. A UDP Port Ranges Table entry.
INT bwaVLUdpPortRangeIdx	1.3.6.1.4.1.12394.1.1.7.10.3.2.3.1.3	INTEGER	read-only	Applicable to all units. UDP Port Range Entry's index
INT bwaVLUdpPortRangeNum	1.3.6.1.4.1.12394.1.1.7.10.3.2.2	INTEGER	read-only	Applicable to all units. The number of entries in the UDP Port Range Table
INT bwaVLUdpPortRangeStart	1.3.6.1.4.1.12394.1.1.7.10.3.2.3.1.1	INTEGER	read-only	Applicable to all units. Start port of an UDP Port Range
bwaVLUdpPortRangeTable	1.3.6.1.4.1.12394.1.1.7.10.3.2.3		not-accessible	Applicable to all units. A table of UDP port ranges use for prioritization. The user can define up to 64 ranges. An entry is empty if start is 65535 and end is 0
INT bwaVLUdpTcpPortRangePrioritizationOption	1.3.6.1.4.1.12394.1.1.7.10.3.1	INTEGER	read-write	Applicable to all units. Disable/Enable Prioritization using UDP and/or TCP Port Ranges. udpOnly(2) : prioritization will be done only for UDP packets tcpOnly(3) : prioritization will be done only for TCP packets udpANDtcp(4): prioritization will be done for UDP and TCP packets
C32 bwaVLUnderrunEvents	1.3.6.1.4.1.12394.1.1.11.2.4.1.3	Counter32	read-only	Applicable to all units. The number of frames whose transmission was aborted because the rate of submitting frames for transmission exceeded the available transmission capability.
INT bwaVLUnicastRelaying	1.3.6.1.4.1.12394.1.1.5.5	INTEGER	read-write	Applicable to AU only. Not applicable to BWA-PtP products. Enables/disables the relaying of unicast messages to the wireless link.
STR bwaVLUnitBootVersion	1.3.6.1.4.1.12394.1.1.1.14	DisplayString	read-only	Applicable to all units. Boot version.
bwaVLUnitControl	1.3.6.1.4.1.12394.1.1.2
STR bwaVLUnitHwVersion	1.3.6.1.4.1.12394.1.1.1.1	DisplayString	read-only	Applicable to all units. Hardware platform version.
IP bwaVLUnitIpAddress	1.3.6.1.4.1.12394.1.1.4.1	IpAddress	read-write	Applicable to all units. IP address of the unit.
MAC bwaVLUnitMacAddress	1.3.6.1.4.1.12394.1.1.1.8	MacAddress	read-only	Applicable to all units. Unit hardware MAC address.
STR bwaVLUnitName	1.3.6.1.4.1.12394.1.1.2.3	DisplayString	read-write	Applicable to all units. The unit name. A string of up to 32 printable ASCII characters.
bwaVLUnitPasswords	1.3.6.1.4.1.12394.1.1.2.8
INT bwaVLUnitType	1.3.6.1.4.1.12394.1.1.1.9	INTEGER	read-only	Applicable to all units. auBS (1) : AU-BS (modular access unit). auSA (2) : AU-SA (stand-alone access unit). su-6-1D (3) : SU-6-1D (subscriber unit supporting 6 Mbps) su-6-BD (4) : SU-6-BD (subscriber unit supporting 6 Mbps). su-24-BD (5) : SU-24-BD (subscriber unit supporting 24 Mbps). bu-B14 (6) : BU-B14 (PtP Base Unit supporting 14 Mbps). bu-B28 (7) : BU-B28 (PtP Base Unit supporting 28 Mbps). rb-B14 (8) : RB-B14 (PtP Remote Bridge supporting 14 Mbps). rb-B28 (9) : RB-B28 (PtP Remote Bridge supporting 28 Mbps). su-BD (10) : SU-BD (subscriber unit). su-54-BD(11) : SU-54-BD (subscriber unit supporting 54 Mbps). su-3-1D (12) : SU-3-1D (subscriber unit supporting 3 Mbps). su-3-4D (13) : SU-3-4D (subscriber unit supporting 3 Mbps). ausBS (14) : AUS-BS (modular access unit supporting maxim 8 or 25 (via licensing) subscribers and allowing association only with SU-3 or SU-6). ausSA (15) : AUS-SA (stand-alone access unit supporting maxim 8 or 25 (via licensing)subscribers and allowing association only with SU-3 or SU-6 ). auBS4900(16) : AU-BS-4900 (BWA 4900 modular access unit) auSA4900(17) : AU-SA-4900 (BWA 4900 stand alone access unit) suBD4900(18) : SU-BD-4900 (BWA 4900 subscriber unit) bu-B100 (19) : BU-B100 (PtP Base Unit unlimited throughput) rb-B100 (20) : BU-B100 (PtP Remote Bridge unlimited throughput) su-I (21) : SU-I au-E (22) : AU-E
NTF bwaVLUnitTypeChangedTRAP	1.3.6.1.4.1.12394.4.1.3.111			Applicable to BU/RB only. This trap is generated when the user change the type of the BWA PtP unit. The RB can be converted in BU or vice versa. The first variable of the trap is the unit MAC Address. The second variable is the new type of the unit
MAC bwaVLUnitWithMaxDistance	1.3.6.1.4.1.12394.1.1.6.15.4	MacAddress	read-only	Applicable AU only. Not applicable to BWA-PtP units. The MAC address of the unit with the maximum distance from the AU.
bwaVLUpLinkQualityIndicator	1.3.6.1.4.1.12394.1.1.11.6
INT bwaVLUpLinkQualityIndicatorStatus	1.3.6.1.4.1.12394.1.1.11.6.3	INTEGER	read-only	Applicable to SU/RB Only. Indicates the test conditions. fullTest means that there are no limitations on the range of available modulation levels, and that all modulation levels from 1 to 8 can be used. limitedTest indicates that the results may not indicate the true quality since the available range is limited - by HW (HW Revision A), or by the applicable parameters in the country code, or by the configurable Maximum Modulation Level parameter.
INT bwaVLUploadEventLogFile	1.3.6.1.4.1.12394.1.1.2.10.4.3	INTEGER	read-write	Applicable to all units. Execution of the event log upload operation.
INT bwaVLUseDhcp	1.3.6.1.4.1.12394.1.1.4.4	INTEGER	read-write	Applicable to all units. DHCP client mode of operation. disabled : Use regular (manual) methods to configure IP parameters. dHCP Only: Use DHCP server to configure IP parameters. automatic: Use DHCP server to configure IP parameters. If a DHCP server is not available, use manually configured values.
INT bwaVLUserFilterOption	1.3.6.1.4.1.12394.1.1.8.1	INTEGER	read-write	Applicable to SU/RB only. Defines user-filtering options. disable: No filtering. iPOnly: Only IP protocol frames pass. userDefinedAddrOnly: Only ip frames to/from user defined IP addresses pass. pPPoE Only: Only PPPoE frames pass.
bwaVLUserFilterParams	1.3.6.1.4.1.12394.1.1.8
INT bwaVLVlanDataPriority	1.3.6.1.4.1.12394.1.1.5.1.6.1	INTEGER	read-write	Applicable to SU/RB only. Priority tagging for data frames. Applicable to Access Link only. Range: 0 to 7.
bwaVLVLANForwarding	1.3.6.1.4.1.12394.1.1.5.1.4
bwaVLVlanForwardingEntry	1.3.6.1.4.1.12394.1.1.5.1.4.2.1		not-accessible	Applicable to all units. A VLAN Forwarding Table entry. (applicable in Trunk and Service Provider links only).
INT bwaVLVlanForwardingSupport	1.3.6.1.4.1.12394.1.1.5.1.4.1	INTEGER	read-write	Applicable to all units. Enables or disables the VLAN forwarding feature. (applicable in Trunk and Service Provider links only).
bwaVLVlanForwardingTable	1.3.6.1.4.1.12394.1.1.5.1.4.2		not-accessible	Applicable to all units. A VLAN Forwarding Table of up to 20 VLAN IDs of devices to which data frames are forwarded when VLAN Forwarding is Enabled. (applicable in Trunk and Service Provider links only).
INT bwaVLVlanForwardingTableIdx	1.3.6.1.4.1.12394.1.1.5.1.4.2.1.1	INTEGER	read-only	Applicable to all units. A read only table index for a VLAN entry in the VLAN Forwarding Table.
INT bwaVLVlanID	1.3.6.1.4.1.12394.1.1.5.1.1	INTEGER	read-write	Applicable to SU/RB only. VLAN ID for data frame tagging. Applicable to Access Link only. Range: 1 to 4094. 0 - not applicable.
INT bwaVLVlanIdForwarding	1.3.6.1.4.1.12394.1.1.5.1.4.2.1.2	INTEGER	read-write	Applicable to all units. The list of VLAN ID's in the VLAN ID Forwarding Table. To Remove a VLAN ID - SET the corresponding entry to 0. To Add a new VLAN ID SET an entry which is currently 0. Range : 0 to 4094
INT bwaVLVlanIdRelaying	1.3.6.1.4.1.12394.1.1.5.1.5.2.1.2	INTEGER	read-write	Applicable to AU only. Not applicable to BWA-PtP products. The list of VLAN ID's in the VLAN ID Relaying Table. To Remove a VLAN ID - SET the corresponding entry to 0. To Add a new VLAN ID SET an entry which is currently 0. Range: 0 to 4094 , 0 - remove entry.
INT bwaVLVlanManagementPriority	1.3.6.1.4.1.12394.1.1.5.1.6.2	INTEGER	read-write	Applicable to all units. Priority tagging for management frames. Applicable to Access Link and Trunk Link only. Range: 0 to 7.
INT bwaVLVLANPriorityThreshold	1.3.6.1.4.1.12394.1.1.5.1.6.3	INTEGER	read-write	Applicable to all units. Not applicable to units with SW version 3.1 or higher. Priority threshold for tagged frames received from Ethernet port. Applicable to Hybrid Link and Trunk Link only. Valid values: 0-7.
bwaVLVLANQinQ	1.3.6.1.4.1.12394.1.1.5.1.7
bwaVLVlanRelaying	1.3.6.1.4.1.12394.1.1.5.1.5
bwaVLVlanRelayingEntry	1.3.6.1.4.1.12394.1.1.5.1.5.2.1		not-accessible	Applicable to AU only. Not applicable to BWA-PtP products. A VLAN Relaying Table entry. (applicable in Trunk and Service Provider links only).
INT bwaVLVlanRelayingSupport	1.3.6.1.4.1.12394.1.1.5.1.5.1	INTEGER	read-write	Applicable to AU only. Not applicable to BWA-PtP products. Enables or disables VLAN Relaying (applicable in Trunk and Service Provider links only).
bwaVLVlanRelayingTable	1.3.6.1.4.1.12394.1.1.5.1.5.2		not-accessible	Applicable to AU only. Not applicable to BWA-PtP products. A VLAN Relaying Table of up to 20 VLAN IDs of devices to which data frames are relayed when VLAN Relaying is Enabled. (applicable in Trunk and Service Provider links only).
INT bwaVLVlanRelayingTableIdx	1.3.6.1.4.1.12394.1.1.5.1.5.2.1.1	INTEGER	read-only	Applicable to AU only. Not applicable to BWA-PtP products. A table index for a VLAN entry in the VLAN Relaying Table.
bwaVLVLANSupport	1.3.6.1.4.1.12394.1.1.5.1
bwaVLVLANTrafficPriority	1.3.6.1.4.1.12394.1.1.5.1.6
bwaVLWirelessLinkCounters	1.3.6.1.4.1.12394.1.1.11.2.3
bwaVLWirelessLinkEvents	1.3.6.1.4.1.12394.1.1.11.2.4
bwaVLWirelessLinkPrioritization	1.3.6.1.4.1.12394.1.1.7.10.4
INT bwaVLWirelessLinkPrioritizationOption	1.3.6.1.4.1.12394.1.1.7.10.4.1	INTEGER	read-write	Applicable only to AU with a license for the Wireless Link Prioritization feature and to BU-100. Enable/disable the traffic prioritization over the Wireless Link
INT bwaVLWirelessTrapThreshold	1.3.6.1.4.1.12394.1.1.6.4	INTEGER	read-write	Applicable to AU/BU only. A wireless link quality threshold, expressed in % of retransmissions, for sending the bwaVLAUWirelessQualityTRAP. This trap indicate whether the quality has gone below or above the specified threshold. The Threshold Range: 1 to 100 (% retransmissions).
NTF bwaVLWLPrioritizationNotSupportedBySUTRAP	1.3.6.1.4.1.12394.4.1.3.112			Applicable to AU/BU only. This trap is generated when an SU/RB with a SW version below 4.0 that does not support Wireless Link Prioritization is associated with an AU/BU with thw Wireless Link Prioritization Option enabled. The first variable of the trap is the SU/RB MAC Address. The second variable is the SW version of the SU/RB
mngIpFilterEntry	1.3.6.1.4.1.12394.1.1.3.3.1		not-accessible	Applicable to all units. A Management IP Filter Table entry.
mngIpFilterTable	1.3.6.1.4.1.12394.1.1.3.3		not-accessible	Applicable to all units. A Management IP Filter Table of up to 3 IP addresses of devices that are authorized to access the unit for management purposes.
mngTrapEntry	1.3.6.1.4.1.12394.1.1.3.7.1		not-accessible	Applicable to all units. A Management Trap Table entry.
mngTrapTable	1.3.6.1.4.1.12394.1.1.3.7		not-accessible	Applicable to all units. A Management Trap Table of up to 10 IP addresses of stations to send traps to.
MAC mptEthernetStationMACAddress	1.3.6.1.4.1.12394.1.1.11.7.1.1.1	MacAddress	read-only	Applicable to AU/BU only. The MAC address of the Ethernet station. It is used as an index in the MAC Pinpoint Table.
MAC mptUnitMACAddress	1.3.6.1.4.1.12394.1.1.11.7.1.1.2	MacAddress	read-only	Applicable to AU/BU only. The MAC address of the wireless device used by the station with the MAC Address from the index in order to access the wireless network.
products	1.3.6.1.4.1.12394.1
ptp_BU_B100	1.3.6.1.4.1.12394.4.1.23
ptp_BU_B14	1.3.6.1.4.1.12394.4.1.21
ptp_BU_B28	1.3.6.1.4.1.12394.4.1.22
ptp_RB_B100	1.3.6.1.4.1.12394.4.1.33
ptp_RB_B14	1.3.6.1.4.1.12394.4.1.31
ptp_RB_B28	1.3.6.1.4.1.12394.4.1.32

RFC description

Vendor-private MIB for 802.11 wireless LAN management in BWA (Broadband Wireless Access) equipment.

Start monitoring BWA (early Alvarion) VL/4900/PtP wireless bridge or access units (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download BWA-DOT11-WLAN-MIB