All MIBs › BSUWIRELESSIF-MIB
Organization: Aperto Networks
Last Updated: 2003-02-10
Category: Vendor: Alvarion, Wireless and WLAN
Description: Manages wireless air interface parameters and radio channel settings on Alvarion BreezeACCESS base stations.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is BSUWIRELESSIF-MIB?
BSUWIRELESSIF-MIB is an Alvarion module for the BreezeACCESS/PacketWave family of fixed-wireless base station units (BSUs), covering the radio air-interface configuration of each wireless port. It exposes per-port tables for basic wireless port status, RF channel configuration (frequency, band, width), QoS link settings, transmit power control, antenna configuration, and sector assignment. It is directly useful for BSUWIRELESSIF-MIB SNMP monitoring of both hardware and RF-configuration status: port state and reset objects reveal whether a radio port is up or has been administratively reset, while power-control and antenna tables expose settings that affect link budget and coverage, and channel objects confirm RF configuration matches the intended plan. It likely complements a corresponding subscriber-unit (SU) wireless interface MIB in the same Alvarion product suite, and possibly standard interface MIBs for base-level statistics, though this is not explicit in the source data. It is deployed on Alvarion BreezeACCESS/PacketWave base stations used by wireless ISPs and enterprises for fixed point-to-multipoint broadband wireless access.
IPNetwork Monitor allows you to monitor SNMP objects defined in BSUWIRELESSIF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Aperto Networks (Ceragon) PacketWave/WiMAX base station units (BSU)
Monitoring Examples
aniBsuWirelessPortTable/Entry rows (keyed by aniBsuWirelessPort) expose aniBsuPortState and aniBsuPortMacAddr for each radio port, so an admin can detect a port that has gone down or is flagged via aniBsuPortFlag; aniBsuChannelTable reports aniBsuChannelFrequency, aniBsuFrequencyBand, and aniBsuChannelWidth per channel, useful for confirming RF configuration matches plan, while aniBsuPowerControlTable and aniBsuAntennaTable expose transmit power and antenna settings that affect link budget and coverage.
What Can Be Monitored
- wireless port link state
- channel frequency/band/width
- transmit power control
- antenna configuration
- sector configuration
- QoS link settings
This MIB depends on
Related MIBs
Imported Objects
From ANIROOT-MIB
| bsu | OBJECT-IDENTITY |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| INT aniBsuAntennaDiversityFlag | 1.3.6.1.4.1.4325.3.2.8.1.1 | INTEGER | read-only | This flag shows whether antenna diversity has been enabled (1) or disabled (2) for this SU. |
| INT aniBsuAntennaDiversityMode | 1.3.6.1.4.1.4325.3.2.8.1.2 | INTEGER | read-only | This shows whether diversity is Sync Based (1) or Training Sequence Based (2) |
| aniBsuAntennaEntry | 1.3.6.1.4.1.4325.3.2.8.1 | not-accessible | An entry containing Antenna attributes for this particular port. | |
| aniBsuAntennaTable | 1.3.6.1.4.1.4325.3.2.8 | not-accessible | This table contains Antenna related information for each BSU Wireless port. | |
| INT aniBsuBcastAntennaPolarization | 1.3.6.1.4.1.4325.3.2.8.1.4 | INTEGER | read-only | The default broadcast antenna polarization. |
| I32 aniBsuBEBandwidth | 1.3.6.1.4.1.4325.3.2.6.1.1 | Integer32 | read-only | The BE Bandwidth as a percentage of total bandwidth. |
| I32 aniBsuCBRBandwidth | 1.3.6.1.4.1.4325.3.2.6.1.3 | Integer32 | read-only | The CBR Bandwidth as a percentage of total bandwidth. |
| aniBsuChannelEntry | 1.3.6.1.4.1.4325.3.2.4.1 | not-accessible | An entry containing Channel attributes for this particular interface. | |
| STR aniBsuChannelFrequency | 1.3.6.1.4.1.4325.3.2.4.1.2 | DisplayString | read-only | The Current Channel Center Frequency in MHz. If no radio is detected, this object will display a value of 0. When Frequency Band is FDD, both transmit and receive frequencies will be displayed in the format 'transmit frequency - receive frequency'. |
| aniBsuChannelTable | 1.3.6.1.4.1.4325.3.2.4 | not-accessible | This table contains Channel related information for each BSU Wireless interface. | |
| STR aniBsuChannelWidth | 1.3.6.1.4.1.4325.3.2.4.1.4 | DisplayString | read-only | The Width of frequency channel in MHz. |
| I32 aniBsuCIRBandwidth | 1.3.6.1.4.1.4325.3.2.6.1.2 | Integer32 | read-only | The CIR Bandwidth as a percentage of total bandwidth. |
| INT aniBsuFrequencyBand | 1.3.6.1.4.1.4325.3.2.4.1.3 | INTEGER | read-only | The Frequency Band to which the Channel Center Frequency belongs. Valid Range: 1 - 5.3 GHz UNII Band (5250 - 5350 MHz) 12 - 5.3 GHz General Band (5150 - 5350 MHz) 2 - 5.8 GHz UNII Band (5725 - 5825 MHz) 3 - 5.8 GHz General (5725 - 5925 MHz) 10 - 5.8 GHz ISM Band (5725 - 5850 MHz) 4 - 2.6 GHz MMDS Band (2500 - 2689 MHz) 5 - 2.6 GHz General (2500 - 2700 MHz) 6 - 3.5 GHz General (3300 - 3800 MHz) 7 - 3.5 GHz ETSI Band - 50 MHz duplexing Scheme (3410 - 3800 MHz) 8 - 3.5 GHz ETSI Band - 100 MHz duplexing Scheme (3410 - 3800 MHz) 11 - 3.5 GHz FDD Band |
| I32 aniBsuNumServFlowsPerSu | 1.3.6.1.4.1.4325.3.2.4.1.6 | Integer32 | read-only | The number of Service Flows supported per SU. |
| I32 aniBsuNumSusSupported | 1.3.6.1.4.1.4325.3.2.4.1.7 | Integer32 | read-only | The number of SUs supported by this wireless port. |
| INT aniBsuPortFlag | 1.3.6.1.4.1.4325.3.2.1.1.5 | INTEGER | read-write | This flag is used to turn a particular wireless port on or off, that is, to selectively enable(1) or disable(2) a port. It is valid only for configured ports. By default, all configured ports are enabled unless explicitly disabled during configuration. The disabled ports may later be enabled dynamically(without reboot). |
| MAC aniBsuPortMacAddr | 1.3.6.1.4.1.4325.3.2.1.1.2 | MacAddress | read-only | The MAC Address of the wireless port. This field is not applicable when BSU is running as a bridge. The agent will display a blank string for this case. |
| T/F aniBsuPortReset | 1.3.6.1.4.1.4325.3.2.1.1.4 | TruthValue | read-write | This object is used to reset an individual wireless port. Setting this parameter to true(1) causes the port to reset. |
| INT aniBsuPortState | 1.3.6.1.4.1.4325.3.2.1.1.3 | INTEGER | read-only | The current state of the wireless port. |
| aniBsuPowerControlEntry | 1.3.6.1.4.1.4325.3.2.7.1 | not-accessible | An entry containing Power Control attributes for this particular port. | |
| aniBsuPowerControlTable | 1.3.6.1.4.1.4325.3.2.7 | not-accessible | This table contains Power Control related information for each BSU Wireless port. | |
| aniBsuQosLinkEntry | 1.3.6.1.4.1.4325.3.2.6.1 | not-accessible | An entry containing QOS Link attributes for this particular port. | |
| aniBsuQosLinkTable | 1.3.6.1.4.1.4325.3.2.6 | not-accessible | This table contains QOS Link related information for each BSU Wireless port. The total sum of BE, CIR, CBR bandwidths should be 100%. | |
| I32 aniBsuReceivePower | 1.3.6.1.4.1.4325.3.2.7.1.2 | Integer32 | read-write | This parameter sets the upstream receiver power on the WSS. The range is between -60 to -90 (dBm) It cannot be modified when BSU is in point to point mode. |
| aniBsuSectorEntry | 1.3.6.1.4.1.4325.3.2.9.1 | not-accessible | An entry containing Sector attributes for this particular port. | |
| STR aniBsuSectorName | 1.3.6.1.4.1.4325.3.2.9.1.2 | DisplayString | read-only | The descriptive name of the sector identified by aniBsuSectorId. |
| aniBsuSectorTable | 1.3.6.1.4.1.4325.3.2.9 | not-accessible | This table contains Sector related information for each BSU Wireless port. | |
| INT aniBsuSuRadioRegPowerLimit | 1.3.6.1.4.1.4325.3.2.4.1.9 | INTEGER | read-only | This parameter constraints the maximum power at which a SU radio can transmit. This information is conveyed to all the SUs within a WSS via the CD packet. It is equal to the EIRP (Effective Incidental Radiated Power) specified by the Regulatory Body. Note: If you are using an older version of the Configuration Manager, this object is not defined in dBm. Instead, the following values will be displayed: nominal(1), one-level-above-nominal(2), two-levels-above-nominal(3), three-levels-above-nominal(4), one-level-below-nominal(5), two-levels-below-nominal(6) |
| STR aniBsuTargetFrequency | 1.3.6.1.4.1.4325.3.2.4.1.10 | DisplayString | read-only | The Current Target Frequency in MHz. To change the configuration of this value, use the object aniBsuWirelessIfConfTargetFrequency for PW1000 (or aniBsuWirelessPtPConfTargetFrequency for PW620). When Frequency Band is FDD, both transmit and receive frequencies will be displayed in the format 'transmit frequency - receive frequency'. Target frequency cannot be modified for FDD band. |
| aniBsuWirelessAFSConfEntry | 1.3.6.1.4.1.4325.3.2.16.1 | not-accessible | An entry for this particular wireless port. | |
| INT aniBsuWirelessAFSErrPercentage | 1.3.6.1.4.1.4325.3.2.16.1.4 | INTEGER | read-write | Configure AFS minimum error percentage. |
| INT aniBsuWirelessAFSFlag | 1.3.6.1.4.1.4325.3.2.16.1.1 | INTEGER | read-write | Enable or disable AFS. |
| INT aniBsuWirelessAFSMinNotificationDuration | 1.3.6.1.4.1.4325.3.2.16.1.3 | INTEGER | read-write | Configure AFS minimum notification duration (second) |
| INT aniBsuWirelessAFSMinSwitchBytes | 1.3.6.1.4.1.4325.3.2.16.1.5 | INTEGER | read-write | Configure AFS minimum switch bytes. |
| INT aniBsuWirelessAFSMinSwitchDuration | 1.3.6.1.4.1.4325.3.2.16.1.2 | INTEGER | read-write | Configure AFS minimum switch duration in database (second) |
| aniBsuWirelessAFSTable | 1.3.6.1.4.1.4325.3.2.16 | not-accessible | This table is used to configure the BSU wireless AFS parameters per wireless port. | |
| aniBsuWirelessFreqAdminEntry | 1.3.6.1.4.1.4325.3.2.12.1 | not-accessible | An entry containing the frequncy for this particular index. | |
| STR aniBsuWirelessFreqAdminFreqValue | 1.3.6.1.4.1.4325.3.2.12.1.2 | DisplayString | read-write | This object is used to configure the desired frequency values for the frequency table. Upto 19 frequency values can be added to the table. All frequencies should belong to the same frequency band. For range and validation, refer to aniBsuWirelessIfConfTargetFrequency description. Once the values are all added/modified, the object aniBsuWirelessIfConfModify (defined in the aniBsuWirelessIfConfTable) needs to be set to true(1). The aniBsuWirelessIfConfModify flag is used to modify and commit the changes of the dependent wireless parameters including all the entries of the aniBsuWirelessFreqAdminTable. If the validation fails when aniBsuWirelessIfConfModify is set to true(1), these changes are not commited and an error is returned. In that case, the modified parameters in this table may not reflect the correct values. They will display the values last configured by the user, rather than the actual values on the device. To view the current values, refer to the aniBsuWirelessFreqOperTable. Each entry in this aniBsuWirelessFreqAdminTable has a corresponding entry displaying the actual values in the aniBsuWirelessFreqOperTable. |
| INT aniBsuWirelessFreqAdminIndex | 1.3.6.1.4.1.4325.3.2.12.1.1 | INTEGER | read-only | The index for this table. |
| aniBsuWirelessFreqAdminTable | 1.3.6.1.4.1.4325.3.2.12 | not-accessible | This table is used to configure the BSU frequency table. | |
| aniBsuWirelessFreqOperEntry | 1.3.6.1.4.1.4325.3.2.13.1 | not-accessible | An entry containing the frequncy for this particular index. | |
| STR aniBsuWirelessFreqOperFreqValue | 1.3.6.1.4.1.4325.3.2.13.1.2 | DisplayString | read-only | This object displays the current frequency value within the frequency table. To change the configuration of the frequency table, use the aniBsuWirelessFreqAdminTable. The correspoding entry with a read-write access for this object is aniBsuWirelessFreqAdminFreqValue. |
| INT aniBsuWirelessFreqOperIndex | 1.3.6.1.4.1.4325.3.2.13.1.1 | INTEGER | read-only | The index for this table. |
| aniBsuWirelessFreqOperTable | 1.3.6.1.4.1.4325.3.2.13 | not-accessible | This table is used to view the current frequency table. Each entry in the aniBsuWirelessFreqAdminTable has a corresponding entry in this table. All parameters within this aniBsuWirelessFreqOperTable have read-only access. These objects reflect the actual frequency table values. | |
| aniBsuWirelessIf | 1.3.6.1.4.1.4325.3.2 | This group contains BSU Wireless Interface information. It shows parameters for each configured Wireless Port on the BSU. It displays the following tables: aniBsuWirelessPortTable - with basic wireless port information aniBsuChannelTable - with Channel related information aniBsuQosLinkTable - with QOS Link related information aniBsuPowerControlTable - with Power control related information aniBsuAntennaTable - with Antenna related information aniBsuSectorTable - with Sector related information aniBsuWirelessPtPConfGroup - PacketWave 620 Wireless Configuration group aniBsuWirelessPtpStatusGroup - PacketWave 620 Wireless Status information aniBsuWirelessFreqAdminTable - PacketWave 620/750/1000 FrequencyTable Configuration aniBsuWirelessFreqOperTable - PacketWave 620/750/1000 Current FrequencyTable display aniBsuWirelessSysConfGroup - PacketWave 1000/760 per system Configuration group aniBsuWirelessIfConfTable - PacketWave 1000/760 per port Wireless Configuration table aniBsuWirelessAFSTable - PacketWave 1000/760 per port AFS Configuration table | ||
| aniBsuWirelessIfConfEntry | 1.3.6.1.4.1.4325.3.2.15.1 | not-accessible | An entry for this particular wireless port. | |
| T/F aniBsuWirelessIfConfModify | 1.3.6.1.4.1.4325.3.2.15.1.50 | TruthValue | read-write | This flag is used to modify and commit the changes of the dependent parameters from this group: aniBsuWirelessIfConfTargetFrequency aniBsuWirelessFreqAdminTable Setting this object to true(1) causes the agent to validate the entire set of parameters. If these set of values are acceptable, then the new values are changed on the device. However, for the changes to take effect, it is required to upload the configuration (set aniDevControlStartUpload in the device_control.mib to true) and then reboot the device. If the validation fails when aniBsuWirelessIfConfModify is set to true(1), the changes are not commited and an error is returned. In that case, the modified parameters in this group may not reflect the correct values. They will display the values last configured by the user, rather than the current values on the device. To view the current values for aniBsuWirelessIfConfTargetFrequency refer to aniBsuTargetFrequency aniBsuWirelessFreqAdminTable refer to aniBsuWirelessFreqOperTable A Get request on this object will always return false(2). |
| STR aniBsuWirelessIfConfSwitchToFrequency | 1.3.6.1.4.1.4325.3.2.15.1.3 | DisplayString | read-write | The Frequency selected to be switched. This frequency should be either one of the frequency entries in the aniBsuWirelessFreqOperTable or the current target frequency aniBsuTargetFrequency. A get request on this object will display the current frequency, aniBsuChannelFrequency and if no radio is detected, it will display 0.00. |
| aniBsuWirelessIfConfTable | 1.3.6.1.4.1.4325.3.2.15 | not-accessible | This table is used to configure the BSU wireless parameters per wireless port. | |
| STR aniBsuWirelessIfConfTargetFrequency | 1.3.6.1.4.1.4325.3.2.15.1.1 | DisplayString | read-write | The Target Frequency in MHz. Its range depends on Channel Width. 1) 5.3 GHz UNII Band (5250 - 5350 MHz). The center frequencies in this band are within 5250 + Half of Channel Width MHz and 5350 - Half of Channel Width MHz and can have any integer value (in MHz) 2) 5.8 GHz UNII Band (5725 - 5825 MHz). The center frequencies in this band are within 5725 + Half of Channel Width MHz and 5825 - Half of Channel Width MHz and can have any integer value (in MHz). 3) 5.8 GHz General (5650 - 5925 MHz). The center frequencies in this band are within 5650 + Half of Channel Width MHz and 5925 - Half of Channel Width MHz and can have any integer value (in MHz). 4) 2.6 GHz MMDS Band (2500 - 2689 MHz). The center frequencies in this band are 2503 + 6N MHz where N = 0,1,2,.,30 5) 2.6 GHz General (2500 - 2700 MHz). The center frequencies in this band are within 2500 + Half of Channel Width MHz and 2700 - Half of Channel Width MHz and can have any integer value (in MHz). 6) 3.5 GHz General (3300 - 3800 MHz). The center frequencies in this band are within 3300 + Half of Channel Width MHz and 3800 - Half of Channel Width MHz and can have any integer value (in MHz). 7) 3.5 GHz ETSI Band - 50 MHz duplexing Scheme (3410 - 3800 MHz). 8) 3.5 GHz ETSI Band - 100 MHz duplexing scheme (3410 - 3800 MHz). 10) 5.8 GHz ISM Band (5725 - 5850 MHz). The center frequencies in this band are within 5725 + Half of Channel Width MHz and 5850 - Half of Channel Width MHz and can have any integer value (in MHz). 11) 5.3 GHz General Band (5150 - 5350 MHz). The center frequencies in this band are within 5150 + Half of Channel Width MHz and 5350 - Half of Channel Width MHz and can have any integer value (in MHz) Note: The term Half of Channel Width in all the descriptions above, is a rounded off value (with 0.5 rounded to 1). Note: When this object is changed through SNMP agent, the value could take effect immediately depending on the current channel center frequency value. If aniBsuWirelessIfConfTargetFrequency is modified, but the current aniBsuChannelFrequency value is still one of the entries in aniBsuWirelessFreqOperTable, then the target frequency will not take effect immediately. However it could take effect later on when the current frequency entry is deleted from the frequency table. |
| STR aniBsuWirelessIfConfVerifyAllSu | 1.3.6.1.4.1.4325.3.2.15.1.2 | DisplayString | read-only | This flag is used to verify if the current set of BSU wireless parameters, that is, aniBsuWirelessPtPConfChannelWidth, aniBsuWirelessPtPConfTargetFrequency, aniBsuWirelessPtPConfBsuId are correctly configured on all the SUs connected. The values are compared against all the SUs connected to this BSU. Sending a Get request on this object causes the agent to verify the above set of parameters. If these set of values are incorrect, an error string is returned indicating that some values are not in sync. If the current set of values are correct, then the string 'No error' is displayed. This object might require upto 10 seconds to respond if multiple SUs are connected. Therefore, to ensure that it does not timeout before getting the complete results, the SNMP Manager tool should increase it's timeout value for this object to more than 10 seconds. |
| INT aniBsuWirelessPort | 1.3.6.1.4.1.4325.3.2.1.1.1 | INTEGER | read-only | The wireless port number. |
| aniBsuWirelessPortEntry | 1.3.6.1.4.1.4325.3.2.1.1 | not-accessible | An entry containing basic information for this particular wireless port. | |
| aniBsuWirelessPortTable | 1.3.6.1.4.1.4325.3.2.1 | not-accessible | This table contains entries with basic information about each BSU Wireless Port. | |
| STR aniBsuWirelessPtPConfBsuId | 1.3.6.1.4.1.4325.3.2.10.11 | DisplayString | read-write | The unique AP/BSU identifier. This is the AP ID required for generating seed for frequency reuse support. Note: When this object is changed through SNMP agent, it is required to upload the configuration (set aniDevControlStartUpload in the device_control.mib to true) and then reboot the device for the changes to take effect. |
| INT aniBsuWirelessPtPConfBsuRadioRegPowerLimit | 1.3.6.1.4.1.4325.3.2.10.8 | INTEGER | read-write | It is the maximum power at which the BSU radio is allowed to transmit. Antenna Gain is added to this maximum power to get EIRP (Effective Incidental Radiated Power) Valid Range - For 5.3GHz radios: 8 to 20 dBm For 5.8GHz radios: 8 to 20 dBm For 3.5GHz radios: 10 to 23 dBm For 2.6GHz radios: 10 to 23 dBm |
| INT aniBsuWirelessPtPConfCellRadius | 1.3.6.1.4.1.4325.3.2.10.4 | INTEGER | read-write | The cell radius or link distance Refer to the constraints listed under aniBsuWirelessPtPConfChannelWidth description. Note: When this object is changed through SNMP agent, it is required to upload the configuration (set aniDevControlStartUpload in the device_control.mib to true) and then reboot the device for the changes to take effect. |
| INT aniBsuWirelessPtPConfChannelWidth | 1.3.6.1.4.1.4325.3.2.10.2 | INTEGER | read-write | The Channel Width. width-2 refers to 2MHz, width-3 refers to 3MHz width-4 refers to 4MHz, width-5 refers to 5MHz,width-6 refers to 6MHz width-7 refers to 7MHz, width-1-75 refers to 1.75MHz, width-3-5 refers to 3.5MHz Channel Width depends on Frequency Band. The valid range is as follows: 3.5 GHz (ETSI) should allow channel width 3.5, 7; the rest of bands should allow channel width 2,3, 4, 5 and 6 The Channel Width, Frame size, Downstream/Upstream ratio and cell radius are dependent on each other and the following restrictions should be taken into account when configuring the system: Low Latency Mode Channel Width = 1.75, 2, 3, 3.5 or 4 Not supported Channel Width = 5, distance must be = 50 Channel Width = 6 or 7, distance must be = 50 Normal Mode Channel Width = 1.75 Not supported Channel Width = 2, if DS/US is 50/50 then distance must be = 50 Note: It is required to upload the configuration and then reboot the device for the changes to take effect. |
| INT aniBsuWirelessPtPConfDSUSRatio | 1.3.6.1.4.1.4325.3.2.10.5 | INTEGER | read-write | The Downstream upstream ratio (DS/US ratio). This allows the user to configure how the total available bandwidth is split between downstream and upsteam. ds70-us30 is 70/30 ds60-us40 is 60/40 ds50-us50 is 50/50 ds40-us60 is 40/60 ds30-us70 is 30/70 Also refer to the constraints listed under aniBsuWirelessPtPConfChannelWidth description. Note: When this object is changed through SNMP agent, it is required to upload the configuration (set aniDevControlStartUpload in the device_control.mib to true) and then reboot the device for the changes to take effect. |
| INT aniBsuWirelessPtPConfFrequencyBand | 1.3.6.1.4.1.4325.3.2.10.1 | INTEGER | read-only | The Frequency Band to which the Channel Center Frequency belongs. Valid Range: 1 - 5.3 GHz UNII Band (5250 - 5350 MHz) 12 - 5.3 GHz General Band (5150 - 5350 MHz) 2 - 5.8 GHz UNII Band (5725 - 5825 MHz) 3 - 5.8 GHz General (5650 - 5925 MHz) 10 - 5.8 GHz ISM Band (5725 - 5850 MHz) 4 - 2.6 GHz MMDS Band (2500 - 2689 MHz) 5 - 2.6 GHz General (2500 - 2700 MHz) 6 - 3.5 GHz General (3300 - 3800 MHz) 7 - 3.5 GHz ETSI Band - 50 MHz duplexing Scheme (3410 - 3800 MHz) 8 - 3.5 GHz ETSI Band - 100 MHz duplexing Scheme (3410 - 3800 MHz) |
| aniBsuWirelessPtPConfGroup | 1.3.6.1.4.1.4325.3.2.10 | |||
| T/F aniBsuWirelessPtPConfModify | 1.3.6.1.4.1.4325.3.2.10.10 | TruthValue | read-write | This flag is used to modify and commit the changes of the dependent parameters from this group: aniBsuWirelessPtPConfChannelWidth aniBsuWirelessPtPConfTDDFrameSize aniBsuWirelessPtPConfCellRadius aniBsuWirelessPtPConfDSUSRatio aniBsuWirelessPtPConfPolarization aniBsuWirelessPtPConfTargetFrequency aniBsuWirelessPtPConfBsuRadioRegPowerLimit aniBsuWirelessPtPConfSuRadioRegPowerLimit aniBsuWirelessFreqAdminTable Setting this object to true(1) causes the agent to validate the entire set of parameters. If these set of values are acceptable, then the new values are changed on the device. However, for the changes to take effect, it is required to upload the configuration (set aniDevControlStartUpload in the device_control.mib to true) and then reboot the device. If the validation fails when aniBsuWirelessPtPConfModify is set to true(1), the changes are not commited and an error is returned. In that case, the modified parameters in this group may not reflect the correct values. They will display the values last configured by the user, rather than the current values on the device. To view the current values for aniBsuWirelessPtPConfChannelWidth refer to aniBsuChannelWidth aniBsuWirelessPtPConfTDDFrameSize refer to aniBsuTDDFrameSize aniBsuWirelessPtPConfCellRadius refer to aniBsuStatusCellRadius (bsu_status.mib) aniBsuWirelessPtPConfTargetFrequency refer to aniBsuTargetFrequency aniBsuWirelessPtPConfBsuRadioRegPowerLimit refer to aniBsuWssRadioRegPowerLimit aniBsuWirelessPtPConfSuRadioRegPowerLimit refer to aniBsuSuRadioRegPowerLimit aniBsuWirelessFreqAdminTable refer to aniBsuWirelessFreqOperTable A Get request on this object will always return false(2). |
| INT aniBsuWirelessPtPConfPolarization | 1.3.6.1.4.1.4325.3.2.10.6 | INTEGER | read-only | The antenna polarization. |
| INT aniBsuWirelessPtPConfSuAFSTimeout | 1.3.6.1.4.1.4325.3.2.10.14 | INTEGER | read-write | Configure AFS SU Timeout (second) |
| INT aniBsuWirelessPtPConfSuRadioRegPowerLimit | 1.3.6.1.4.1.4325.3.2.10.9 | INTEGER | read-write | It is the maximum power at which a SU radio is allowed to transmit. This information is conveyed to all the SUs via the CD packet. Antenna Gain is added to this maximum power to get EIRP (Effective Incidental Radiated Power) Valid Range - For 5.3GHz radios: 8 to 20 dBm For 5.8GHz radios: 8 to 20 dBm For 3.5GHz radios: 10 to 23 dBm For 2.6GHz radios: 10 to 23 dBm |
| STR aniBsuWirelessPtPConfSwitchToFrequency | 1.3.6.1.4.1.4325.3.2.10.13 | DisplayString | read-write | The Frequency selected to be switched. This frequency should be either one of the frequency entries in the aniBsuWirelessFreqOperTable or the current target frequency aniBsuTargetFrequency. A get request on this object will display the current frequency, aniBsuChannelFrequency and if no radio is detected, it will display 0.00. |
| STR aniBsuWirelessPtPConfTargetFrequency | 1.3.6.1.4.1.4325.3.2.10.7 | DisplayString | read-write | The Target Frequency in MHz. Its range depends on Channel Width. 1) 5.3 GHz UNII Band (5250 - 5350 MHz). The center frequencies in this band are within 5250 + Half of Channel Width MHz and 5350 - Half of Channel Width MHz and can have any integer value (in MHz) 2) 5.8 GHz UNII Band (5725 - 5825 MHz). The center frequencies in this band are within 5725 + Half of Channel Width MHz and 5825 - Half of Channel Width MHz and can have any integer value (in MHz). 3) 5.8 GHz General (5650 - 5925 MHz). The center frequencies in this band are within 5650 + Half of Channel Width MHz and 5925 - Half of Channel Width MHz and can have any integer value (in MHz). 4) 2.6 GHz MMDS Band (2500 - 2689 MHz). The center frequencies in this band are 2503 + 6N MHz where N = 0,1,2,.,30 5) 2.6 GHz General (2500 - 2700 MHz). The center frequencies in this band are within 2500 + Half of Channel Width MHz and 2700 - Half of Channel Width MHz and can have any integer value (in MHz). 6) 3.5 GHz General (3300 - 3800 MHz). The center frequencies in this band are within 3300 + Half of Channel Width MHz and 3800 - Half of Channel Width MHz and can have any integer value (in MHz). 7) 3.5 GHz ETSI Band - 50 MHz duplexing Scheme (3410 - 3800 MHz). 8) 3.5 GHz ETSI Band - 100 MHz duplexing scheme (3410 - 3800 MHz). 10) 5.8 GHz ISM Band (5725 - 5850 MHz). The center frequencies in this band are within 5725 + Half of Channel Width MHz and 5850 - Half of Channel Width MHz and can have any integer value (in MHz). 11) 5.3 GHz General Band (5150 - 5350 MHz). The center frequencies in this band are within 5150 + Half of Channel Width MHz and 5350 - Half of Channel Width MHz and can have any integer value (in MHz) Note: The term Half of Channel Width in all the descriptions above, is a rounded off value (with 0.5 rounded to 1). Note: When this object is changed through SNMP agent, the value could take effect immediately depending on the current channel center frequency value. If aniBsuWirelessPtPConfTargetFrequency is modified, but the current aniBsuChannelFrequency value is still one of the entries in aniBsuWirelessFreqOperTable, then the target frequency will not take effect immediately. However it could take effect later on when the current frequency entry is deleted from the frequency table. |
| INT aniBsuWirelessPtPConfTDDFrameSize | 1.3.6.1.4.1.4325.3.2.10.3 | INTEGER | read-write | The total size of the TDD Frame. For PW620, only low-latency and normal-mode are allowed. Also refer to the constraints listed under aniBsuWirelessPtPConfChannelWidth description. Note: When this object is changed through SNMP agent, it is required to upload the configuration (set aniDevControlStartUpload in the device_control.mib to true) and then reboot the device for the changes to take effect. |
| STR aniBsuWirelessPtPConfVerifyAllSu | 1.3.6.1.4.1.4325.3.2.10.12 | DisplayString | read-only | This flag is used to verify if the current set of BSU wireless parameters, that is, aniBsuWirelessPtPConfChannelWidth, aniBsuWirelessPtPConfTargetFrequency, aniBsuWirelessPtPConfBsuId are correctly configured on all the SUs connected. The values are compared against all the SUs connected to this BSU. Sending a Get request on this object causes the agent to verify the above set of parameters. If these set of values are incorrect, an error string is returned indicating that some values are not in sync. If the current set of values are correct, then the string 'No error' is displayed. This object might require upto 10 seconds to respond if multiple SUs are connected. Therefore, to ensure that it does not timeout before getting the complete results, the SNMP Manager tool should increase it's timeout value for this object to more than 10 seconds. |
| aniBsuWirelessPtPStatusGroup | 1.3.6.1.4.1.4325.3.2.11 | |||
| STR aniBsuWirelessPtPStatusMaxDSAvailBW | 1.3.6.1.4.1.4325.3.2.11.1 | DisplayString | read-only | The maximum Downstream available bandwidth in kbps based on the current wireless configuration. |
| STR aniBsuWirelessPtPStatusMaxUSAvailBW | 1.3.6.1.4.1.4325.3.2.11.2 | DisplayString | read-only | The maximum Upstream available bandwidth in kbps based on the current wireless configuration. |
| INT aniBsuWirelessPtPStatusTDDFrameSize | 1.3.6.1.4.1.4325.3.2.11.3 | INTEGER | read-only | The total size of the TDD Frame low-latency is 2000 ticks normal-mode is 5000 ticks or 2500 ticks For PW620, only low-latency and normal-mode are allowed. Also refer to the constraints listed under aniBsuWirelessPtPConfChannelWidth description. |
| STR aniBsuWirelessSysConfBsuId | 1.3.6.1.4.1.4325.3.2.14.1 | DisplayString | read-write | The unique BSU identifier. This is the BSU ID required for generating seed for frequency reuse support. Note: When this object is changed through SNMP agent, it is required to upload the configuration (set aniDevControlStartUpload in the device_control.mib to true) and then reboot the device for the changes to take effect. |
| INT aniBsuWirelessSysConfDSUSRatio | 1.3.6.1.4.1.4325.3.2.14.5 | INTEGER | read-only | The Downstream upstream ratio (DS/US ratio). ds70-us30 is 70/30 ds60-us40 is 60/40 ds50-us50 is 50/50 ds40-us60 is 40/60 ds30-us70 is 30/70 |
| I32 aniBsuWirelessSysConfFrameDownstreamSize | 1.3.6.1.4.1.4325.3.2.14.3 | Integer32 | read-only | The number of ticks in the Downstream portion of the frame. |
| I32 aniBsuWirelessSysConfFrameSize | 1.3.6.1.4.1.4325.3.2.14.2 | Integer32 | read-only | The total size of the Frame in ticks. |
| I32 aniBsuWirelessSysConfFrameUpstreamSize | 1.3.6.1.4.1.4325.3.2.14.4 | Integer32 | read-only | The number of ticks in the Upstream portion of the frame. |
| aniBsuWirelessSysConfGroup | 1.3.6.1.4.1.4325.3.2.14 | |||
| INT aniBsuWssRadioRegPowerLimit | 1.3.6.1.4.1.4325.3.2.7.1.3 | INTEGER | read-only | This parameter constraints the maximum power at which the radio for this WSS can transmit. It is equal to the EIRP (Effective Incidental Radiated Power) specified by the Regulatory Body. Note: If you are using an older version of the Configuration Manager, this object is not defined in dBm. Instead, the following values will be displayed: nominal(1), one-level-above-nominal(2), two-levels-above-nominal(3), three-levels-above-nominal(4), one-level-below-nominal(5), two-levels-below-nominal(6) |
FAQ
What would I check in BSUWIRELESSIF-MIB if a fixed-wireless base station's link quality suddenly degrades?
BSUWIRELESSIF-MIB exposes per-port tables for the wireless air interface on an Alvarion BreezeACCESS/PacketWave base station -- including a channel table (frequency, band, width), a power-control table, and an antenna table. If a link degrades, you'd check the channel table to confirm the RF configuration still matches the intended plan and the power-control/antenna tables to see if transmit power or antenna settings have drifted from what's expected.
How does BSUWIRELESSIF-MIB help confirm a wireless port is actually up on a BreezeACCESS base station?
The module includes a basic wireless port table (aniBsuWirelessPortTable) alongside sector and QoS-link tables, so port state and reset objects reveal whether a given radio port on the BSU is operational or has been administratively reset. This makes it a first stop for confirming a BSU's air interface is live before digging into channel or antenna configuration details.
RFC description
Aperto Networks BSU wireless interface MIB for point-to-point radio configuration parameters and PtP management.
Start monitoring Aperto Networks (Ceragon) PacketWave/WiMAX base station units (BSU) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.