All MIBs › XPPC-MIB
Category: Miscellaneous and Vendor Registration
Description: Manages XPPC protocol configuration, connection establishment, and data transfer performance statistics.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is XPPC-MIB?
XPPC-MIB is a legacy enterprise MIB (registered under a "ppc"/"products"/"ppcmgmt" branch) whose visible objects indicate it manages both SNMP trap-receiver configuration and UPS (uninterruptible power supply) identity/firmware data, despite its short description characterizing it around a generic "XPPC protocol." Its exposed data spans a trap-receiver table (destination address, community string, severity level, accept flag) for configuring where the device sends its own SNMP traps, alongside UPS identity objects covering model name, firmware revision, and date of manufacture. Given the UPS-oriented objects present, its practical monitoring role centers on hardware status -- specifically power-protection equipment identity and firmware version -- combined with software-side configuration of alert/notification routing via the trap-receiver table. No clear external MIB dependency is indicated by the available data, so it appears to be a largely self-contained vendor enterprise MIB. It would be deployed on the vendor's UPS or power-management appliance, where this XPPC-MIB reference helps operators both configure trap-notification destinations and confirm the unit's model/firmware identity.
IPNetwork Monitor allows you to monitor SNMP objects defined in XPPC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- vendor UPS/power-management appliance (PPC product line)
Monitoring Examples
An administrator would poll mconfigTrapsReceiversTable/mconfigTrapsReceiversEntry, indexed by trapsIndex, to verify each configured trapsReceiverAddr, receiverCommunityString, and severityLevel is correct so that alert notifications reach the intended management station, and check receiverAccept to confirm a receiver entry is enabled. Separately, reading upsBaseIdentModel, upsBaseIdentUpsName, and upsSmartIdentFirmwareRevision confirms which UPS model and firmware version is installed, useful when auditing a fleet for firmware currency. upsSmartIdentDateOfManufacture helps identify aging units that may be approaching end-of-life for battery replacement planning.
What Can Be Monitored
- trap receiver address/community/severity configuration
- trap receiver enable status
- UPS model and name identity
- UPS firmware revision
- UPS manufacture date
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| IpAddress | |
| enterprises |
From RFC1213-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| NTF boostOn | 1.3.6.1.4.1.935.0.6 | WARNING: The UPS has enabled Boost. | ||
| NTF buckOn | 1.3.6.1.4.1.935.0.68 | WARNING: The UPS has enabled Buck. | ||
| NTF communicationEstablished | 1.3.6.1.4.1.935.0.8 | INFORMATION: Communication with the UPS has been established. | ||
| NTF communicationLost | 1.3.6.1.4.1.935.0.1 | SEVERE: Communication to the UPS has been lost. Steps to reestablish communication are in progress. | ||
| INT deviceAccept | 1.3.6.1.4.1.935.1.1.1.5.1.2.1.4 | INTEGER | read-write | An entry is added if yes, the entry is deleted if no. |
| NTF envGasAbnormal | 1.3.6.1.4.1.935.0.26 | WARNING: Gas Alarm | ||
| NTF envHumidityNormal | 1.3.6.1.4.1.935.0.19 | INFORMATION: The environment humidity is normal. | ||
| NTF envOverHumidity | 1.3.6.1.4.1.935.0.18 | WARNING: The environment humidity exceed the normal value. | ||
| NTF envOverTemperature | 1.3.6.1.4.1.935.0.16 | WARNING: The environment temperature exceed the normal value. | ||
| NTF envSecurity1 | 1.3.6.1.4.1.935.0.33 | WARNING: Security1 Alarm. | ||
| NTF envSecurity2 | 1.3.6.1.4.1.935.0.34 | WARNING: Security2 Alarm. | ||
| NTF envSecurity3 | 1.3.6.1.4.1.935.0.35 | WARNING: Security3 Alarm. | ||
| NTF envSecurity4 | 1.3.6.1.4.1.935.0.36 | WARNING: Security4 Alarm. | ||
| NTF envSecurity5 | 1.3.6.1.4.1.935.0.37 | WARNING: Security5 Alarm. | ||
| NTF envSecurity6 | 1.3.6.1.4.1.935.0.38 | WARNING: Security6 Alarm. | ||
| NTF envSecurity7 | 1.3.6.1.4.1.935.0.39 | WARNING: Security7 Alarm. | ||
| NTF envSecurityAbnormal | 1.3.6.1.4.1.935.0.22 | WARNING: Security is abnormal. | ||
| NTF envSmokeAbnormal | 1.3.6.1.4.1.935.0.20 | WARNING: Smoke is abnormal. | ||
| NTF envTemperatureNormal | 1.3.6.1.4.1.935.0.17 | INFORMATION: The environment temperature is normal. | ||
| NTF envUnderHumidity | 1.3.6.1.4.1.935.0.31 | WARNING: The environment humidity below the normal value. | ||
| NTF envUnderTemperature | 1.3.6.1.4.1.935.0.30 | WARNING: The environment temperature below the normal value. | ||
| NTF envWaterAbnormal | 1.3.6.1.4.1.935.0.21 | WARNING: Water is abnormal. | ||
| NTF envWaterNormal | 1.3.6.1.4.1.935.0.24 | INFORMATION: Water is normal. | ||
| hardware | 1.3.6.1.4.1.935.1.1 | |||
| INT indexOfDevice | 1.3.6.1.4.1.935.1.1.1.5.1.2.1.1 | INTEGER | read-only | The index of the device that is plugged into the UPS. |
| NTF lowBattery | 1.3.6.1.4.1.935.0.7 | SEVERE: The UPS batteries are low and will soon be exhausted. If utility power is not restored the UPS will put itself to 'sleep' and immediately cut power to the load. | ||
| mconfig | 1.3.6.1.4.1.935.2.1 | |||
| mconfigTrapsReceiversEntry | 1.3.6.1.4.1.935.2.1.2.1 | not-accessible | The managers to send traps to. | |
| INT mconfigTrapsReceiversNum | 1.3.6.1.4.1.935.2.1.1 | INTEGER | read-only | The number of managers to send traps to. |
| mconfigTrapsReceiversTable | 1.3.6.1.4.1.935.2.1.2 | not-accessible | A list of managers to send traps to. The number of entries is given by the value of mconfigNumTrapReceivers | |
| STR nameOfDevice | 1.3.6.1.4.1.935.1.1.1.5.1.2.1.2 | DisplayString | read-write | The name/description of the device plugged into the UPS. |
| NTF powerRestored | 1.3.6.1.4.1.935.0.9 | INFORMATION: Utility power has been restored. | ||
| ppc | 1.3.6.1.4.1.935 | |||
| ppcmgmt | 1.3.6.1.4.1.935.2 | |||
| products | 1.3.6.1.4.1.935.1 | |||
| INT receiverAccept | 1.3.6.1.4.1.935.2.1.2.1.5 | INTEGER | read-write | An entry will become active if yes, and will be deleted if no. |
| STR receiverCommunityString | 1.3.6.1.4.1.935.2.1.2.1.3 | DisplayString | read-write | The community name to use in the trap when sent to the manager. |
| NTF returnFromBoost | 1.3.6.1.4.1.935.0.70 | WARNING: The UPS has return from Boost. | ||
| NTF returnFromBuck | 1.3.6.1.4.1.935.0.69 | WARNING: The UPS has return from Buck. | ||
| NTF returnFromLowBattery | 1.3.6.1.4.1.935.0.11 | INFORMATION: The UPS has returned from a low battery condition. | ||
| INT severityLevel | 1.3.6.1.4.1.935.2.1.2.1.4 | INTEGER | read-write | The severity threshold of traps to send to the manager. traps are labeled in severity as informational(1), warning(2), severe(3). Only traps of equal or greater severity than this value are sent to the manager. |
| INT trapsIndex | 1.3.6.1.4.1.935.2.1.2.1.1 | INTEGER | read-only | The index to a trap receiver entry. |
| IP trapsReceiverAddr | 1.3.6.1.4.1.935.2.1.2.1.2 | IpAddress | read-write | The IP address of the manager to send a trap to. |
| ups | 1.3.6.1.4.1.935.1.1.1 | |||
| upsBaseBattery | 1.3.6.1.4.1.935.1.1.1.2.1 | |||
| STR upsBaseBatteryLastReplaceDate | 1.3.6.1.4.1.935.1.1.1.2.1.3 | DisplayString | read-write | The date when the UPS system's batteries were last replaced in mm/dd/yy format. For UPS models, this value is originally set in the factory. When the UPS batteries are replaced, this value should be reset by the administrator. |
| INT upsBaseBatteryStatus | 1.3.6.1.4.1.935.1.1.1.2.1.1 | INTEGER | read-only | The status of the UPS batteries. A batteryLow(3) value indicates the UPS will be unable to sustain the current load, and its services will be lost if power is not restored. The amount of run time in reserve at the time of low battery can be configured by the upsSmartConfigLowBatteryRunTime. |
| INT upsBaseBatteryTimeOnBattery | 1.3.6.1.4.1.935.1.1.1.2.1.2 | INTEGER | read-only | The elapsed time in seconds since the UPS has switched to battery power. |
| upsBaseConfig | 1.3.6.1.4.1.935.1.1.1.5.1 | |||
| upsBaseConfigDeviceEntry | 1.3.6.1.4.1.935.1.1.1.5.1.2.1 | not-accessible | The devices plugged in to the UPS. | |
| upsBaseConfigDeviceTable | 1.3.6.1.4.1.935.1.1.1.5.1.2 | not-accessible | A list of devices that are plugged into the UPS. The number of entries is given by the value of upsBaseConfigNumDevices. | |
| INT upsBaseConfigNumDevices | 1.3.6.1.4.1.935.1.1.1.5.1.1 | INTEGER | read-only | The number of devices that are plugged into the UPS. |
| upsBaseControl | 1.3.6.1.4.1.935.1.1.1.6.1 | |||
| INT upsBaseControlConserveBattery | 1.3.6.1.4.1.935.1.1.1.6.1.1 | INTEGER | read-write | Setting this variable to turnUpsOffToConserveBattery(2) causes a UPS on battery to be put into 'sleep' mode immediately. The (10) means suspending time(10 minutes) before turn off UPS. UPS will turn back on when utility power is restored. Attempting to turn off a UPS that is not on battery will result in a badValue error. Setting this value to noTurnOffUps(1) has no effect. The value noTurnOffUps(1) will always be returned when the variable is read. |
| upsBaseIdent | 1.3.6.1.4.1.935.1.1.1.1.1 | |||
| STR upsBaseIdentModel | 1.3.6.1.4.1.935.1.1.1.1.1.1 | DisplayString | read-only | The UPS model name (e.g. 'Intelligent 8000E 900VA'). |
| STR upsBaseIdentUpsName | 1.3.6.1.4.1.935.1.1.1.1.1.2 | DisplayString | read-write | An 8 byte ID string identifying the UPS. This object can be set by the administrator. |
| upsBaseInput | 1.3.6.1.4.1.935.1.1.1.3.1 | |||
| INT upsBaseInputPhase | 1.3.6.1.4.1.935.1.1.1.3.1.1 | INTEGER | read-only | The current AC input phase. |
| upsBaseOutput | 1.3.6.1.4.1.935.1.1.1.4.1 | |||
| INT upsBaseOutputPhase | 1.3.6.1.4.1.935.1.1.1.4.1.2 | INTEGER | read-only | The current output phase. |
| INT upsBaseOutputStatus | 1.3.6.1.4.1.935.1.1.1.4.1.1 | INTEGER | read-only | The current state of the UPS. If the UPS is unable to determine the state of the UPS this variable is set to unknown(1). |
| upsBaseTest | 1.3.6.1.4.1.935.1.1.1.7.1 | |||
| upsBatteryp | 1.3.6.1.4.1.935.1.1.1.2 | |||
| NTF upsBypass | 1.3.6.1.4.1.935.0.32 | WARNING: The UPS is entering 'bypass' mode. | ||
| NTF upsBypassacabnormal | 1.3.6.1.4.1.935.0.50 | WARNING: Bypass AC Abnormal | ||
| NTF upsBypassacnormal | 1.3.6.1.4.1.935.0.49 | WARNING: Bypass AC Normal | ||
| NTF upsBypassBreadkerOnShutdown | 1.3.6.1.4.1.935.0.56 | The UPS Manual Bypass Breaker on Shutdown | ||
| NTF upsBypassFreFail | 1.3.6.1.4.1.935.0.48 | WARNING: Bypass Frequency Fail | ||
| NTF upsBypassMode | 1.3.6.1.4.1.935.0.60 | The UPS Static Switch in Bypass Mode | ||
| NTF upsBypassReturn | 1.3.6.1.4.1.935.0.53 | The UPS return from Bypass Mode | ||
| NTF upsCapacityNormal | 1.3.6.1.4.1.935.0.64 | The UPS Capacity Normal | ||
| NTF upsCapacityUnderrun | 1.3.6.1.4.1.935.0.63 | The UPS Capacity Underrun | ||
| upsConfigp | 1.3.6.1.4.1.935.1.1.1.5 | |||
| upsControlp | 1.3.6.1.4.1.935.1.1.1.6 | |||
| NTF upsDiagnosticsFailed | 1.3.6.1.4.1.935.0.3 | SEVERE: The UPS failed its internal diagnostic self-test. | ||
| NTF upsDiagnosticsPassed | 1.3.6.1.4.1.935.0.10 | INFORMATION: The UPS passed its internal self-test. | ||
| NTF upsDischarged | 1.3.6.1.4.1.935.0.4 | SEVERE: The UPS just started a runtime calibration discharge. The UPS batteries are being discharged. | ||
| NTF upsEmergencyStop | 1.3.6.1.4.1.935.0.58 | The UPS Emergency Stop | ||
| INT upsEnvHumidity | 1.3.6.1.4.1.935.1.1.1.9.1.2 | INTEGER | read-only | The environment humidity. |
| upsEnvironment | 1.3.6.1.4.1.935.1.1.1.9 | |||
| INT upsEnvOverHumidity | 1.3.6.1.4.1.935.1.1.1.9.2.3 | INTEGER | read-write | Alarm dupsAlarmOverHumidity on when the environment humidity over the value. |
| INT upsEnvOverTemperature | 1.3.6.1.4.1.935.1.1.1.9.2.1 | INTEGER | read-write | Alarm dupsAlarmOverTemperature on when the environment temperature over the value. |
| INT upsEnvSecurity1 | 1.3.6.1.4.1.935.1.1.1.9.1.5 | INTEGER | read-only | Security status |
| INT upsEnvSecurity2 | 1.3.6.1.4.1.935.1.1.1.9.1.6 | INTEGER | read-only | Security status |
| INT upsEnvSecurity3 | 1.3.6.1.4.1.935.1.1.1.9.1.7 | INTEGER | read-only | Security status |
| INT upsEnvSecurity4 | 1.3.6.1.4.1.935.1.1.1.9.1.8 | INTEGER | read-only | Security status |
| INT upsEnvSecurity5 | 1.3.6.1.4.1.935.1.1.1.9.1.9 | INTEGER | read-only | Security status |
| INT upsEnvSecurity6 | 1.3.6.1.4.1.935.1.1.1.9.1.10 | INTEGER | read-only | Security status |
| INT upsEnvSecurity7 | 1.3.6.1.4.1.935.1.1.1.9.1.11 | INTEGER | read-only | Security status |
| upsEnvSetting | 1.3.6.1.4.1.935.1.1.1.9.2 | |||
| INT upsEnvSmoke | 1.3.6.1.4.1.935.1.1.1.9.1.4 | INTEGER | read-only | Smoke status |
| upsEnvStatus | 1.3.6.1.4.1.935.1.1.1.9.1 | |||
| INT upsEnvTemperature | 1.3.6.1.4.1.935.1.1.1.9.1.1 | INTEGER | read-only | The ambient environment temperature. |
| INT upsEnvUnderHumidity | 1.3.6.1.4.1.935.1.1.1.9.2.4 | INTEGER | read-write | Alarm dupsAlarmUnderHumidity on when the environment humidity below the value. |
| INT upsEnvUnderTemperature | 1.3.6.1.4.1.935.1.1.1.9.2.2 | INTEGER | read-write | Alarm dupsAlarmUnderTemperature on when the environment temperature below the value. |
| INT upsEnvWater | 1.3.6.1.4.1.935.1.1.1.9.1.3 | INTEGER | read-only | Water status |
| NTF upsHighDCShutdown | 1.3.6.1.4.1.935.0.57 | The UPS High DC Shutdown | ||
| upsIdentp | 1.3.6.1.4.1.935.1.1.1.1 | |||
| upsInputp | 1.3.6.1.4.1.935.1.1.1.3 | |||
| NTF upsInverterMode | 1.3.6.1.4.1.935.0.59 | The UPS Static Switch in Inverter Mode | ||
| NTF upsInverterOutputFailShutdown | 1.3.6.1.4.1.935.0.55 | The UPS Inverter Output Fail Shutdown | ||
| NTF upsLoadNormal | 1.3.6.1.4.1.935.0.28 | WARNING: UPS Load Normal | ||
| NTF upsLowBatteryShutdown | 1.3.6.1.4.1.935.0.67 | The UPS Low Battery Shutdown | ||
| NTF upsOnBattery | 1.3.6.1.4.1.935.0.5 | WARNING: The UPS has switched to battery backup power. | ||
| upsOutputp | 1.3.6.1.4.1.935.1.1.1.4 | |||
| NTF upsOverLoad | 1.3.6.1.4.1.935.0.2 | SEVERE: The UPS has sensed a load greater than 100 percent of its rated capacity. | ||
| NTF upsOverLoadShutdown | 1.3.6.1.4.1.935.0.62 | The UPS Overload Shutdown | ||
| NTF upsOverTemperatureShutdown | 1.3.6.1.4.1.935.0.61 | The UPS Over Temperature Shutdown | ||
| NTF upsRebootStarted | 1.3.6.1.4.1.935.0.15 | WARNING: The UPS has started its reboot sequence. After the specified delay the UPS will perform a reboot. | ||
| NTF upsRecroterror | 1.3.6.1.4.1.935.0.47 | WARNING: Rectifier Rotation Error | ||
| NTF upsScheduleShutdown | 1.3.6.1.4.1.935.0.52 | WARNING: UPS Schedule Shutdown | ||
| NTF upsShortCircuitShutdown | 1.3.6.1.4.1.935.0.54 | The UPS Short Circuit Shutdown | ||
| NTF upsSleeping | 1.3.6.1.4.1.935.0.13 | WARNING: The UPS is entering 'sleep' mode. Power to the load will be cut off. | ||
| upsSmartBattery | 1.3.6.1.4.1.935.1.1.1.2.2 | |||
| INT upsSmartBatteryCapacity | 1.3.6.1.4.1.935.1.1.1.2.2.1 | INTEGER | read-only | The remaining battery capacity expressed in percent of full capacity. |
| INT upsSmartBatteryCurrent | 1.3.6.1.4.1.935.1.1.1.2.2.7 | INTEGER | read-only | The current battery current expressed in percent of maximum current. |
| INT upsSmartBatteryFullChargeVoltage | 1.3.6.1.4.1.935.1.1.1.2.2.6 | INTEGER | read-only | The fully charged battery voltage of the battery system used in the UPS, expressed in tenths of a volt. |
| INT upsSmartBatteryReplaceIndicator | 1.3.6.1.4.1.935.1.1.1.2.2.5 | INTEGER | read-only | Indicates whether the UPS batteries need replacing. |
| INT upsSmartBatteryRunTimeRemaining | 1.3.6.1.4.1.935.1.1.1.2.2.4 | INTEGER | read-only | The UPS battery run time remaining before battery exhaustion, in seconds. |
| INT upsSmartBatteryTemperature | 1.3.6.1.4.1.935.1.1.1.2.2.3 | INTEGER | read-only | The current internal UPS temperature expressed in tenths of a Celsius degree. |
| INT upsSmartBatteryVoltage | 1.3.6.1.4.1.935.1.1.1.2.2.2 | INTEGER | read-only | The current battery voltage expressed in 1/10 VDC. |
| upsSmartConfig | 1.3.6.1.4.1.935.1.1.1.5.2 | |||
| INT upsSmartConfigAlarm | 1.3.6.1.4.1.935.1.1.1.5.2.4 | INTEGER | read-write | A flag indicating how the UPS should handle audible line fail alarms. |
| INT upsSmartConfigAlarmTimer | 1.3.6.1.4.1.935.1.1.1.5.2.5 | INTEGER | read-write | The time in seconds after initial line failure at which the UPS begins emitting audible alarms (beeping). This timer is observerd only if the value of extControlAlarm is timed(2). Allowed values are 0 or 30 seconds. If a value other than a supported value is provided in a set request, the UPS interprets it as a the next lower acceptable value. If the provided value is lower than the lowest acceptable value, the lowest acceptable value is used. |
| INT upsSmartConfigHighTransferVolt | 1.3.6.1.4.1.935.1.1.1.5.2.2 | INTEGER | read-write | The maximum line voltage in 1/10 VAC allowed before the UPS system transfers to battery backup. Allowed value depend on the UPS used: 120 Volt units allow settings of 1290, 1320, 1350, 1380. 100 Volt units allow settings of 1080, 1100, 1120, 1140. 230 Volt units allow settings of 2530, 2640, 2710, 2800. 208 Volt units allow settings of 2240, 2290, 2340, 2390. If a value other than a supported value is provided in a set request, the UPS interprets it as the next lower acceptable value. If the provided value is lower than the lowest acceptable value, the lowest acceptable value is used. |
| INT upsSmartConfigLowBatteryRunTime | 1.3.6.1.4.1.935.1.1.1.5.2.8 | INTEGER | read-write | The desired run time in seconds once the low battery condition is reached. Allowed values are 120, 300, 420, or 600 seconds. During this time the UPS will produce a constant warning tone which can not be disabled. If a value other than a supported value is provided in a set request, the UPS interprets it as a the next higher acceptable value. If the provided value is higher than the highest acceptable value, the highest acceptable value is used. |
| INT upsSmartConfigLowTransferVolt | 1.3.6.1.4.1.935.1.1.1.5.2.3 | INTEGER | read-write | The minimum line voltage in 1/10 VAC allowed before the UPS system transfers to battery backup. Allowable values depend on the UPS used: 120 Volt units allow settings of 970, 1000, 1030, 1060. 100 Volt units allow settings of 810, 830, 850, 870. 230 Volt units allow settings of 1880, 1960, 2040, 2080. 208 Volt units allow settings of 1680, 1720, 1770, 1820. If a value other than a supported value is provided in a set request, the UPS interprets it as a the next higher acceptable value. If the provided value is higher than the highest acceptable value, the highest acceptable value is used. |
| INT upsSmartConfigMinReturnCapacity | 1.3.6.1.4.1.935.1.1.1.5.2.6 | INTEGER | read-write | The minimum battery capacity as a percent of full capacity required before the UPS will return from a low battery shutdown condition. In other words, the UPS will not re-energize the output until the battery capacity is equal to this value. Allowed values are 0, 10, 25, or 90 percent. If a value other than a supported value is provided in a set request, the UPS interprets it as a the next higher acceptable value. If the provided value is higher than the highest acceptable value, the highest acceptable value is used. |
| INT upsSmartConfigRatedOutputVoltage | 1.3.6.1.4.1.935.1.1.1.5.2.1 | INTEGER | read-write | The nominal output voltage from the UPS in 1/10 VAC. Possible values are 1000, 1200, 2080, 2200, 2250, 2300 and 2400. NOTE: Only units that are 2200, 2250, 2300 and 2400 can be changed. Allowable values are 2200, 2250, 2300 and 2400. For these adjustable units, if a value other than a supported value is provided in a set request, the UPS interprets it as the next lower acceptable value. If the provided value is lower than the lowest acceptable value, the lowest acceptable value is used. |
| INT upsSmartConfigReturnDelay | 1.3.6.1.4.1.935.1.1.1.5.2.9 | INTEGER | read-write | The delay in seconds after utility line power returns before the UPS will turn on. This value is also used when the UPS comes out of a reboot and before the UPS wakes up from 'sleep' mode. Allowed values are 0, 60, 180 and 300 seconds. If a value other than a supported value is provided in a set request, the UPS interprets it as a the next higher acceptable value. If the provided value is higher than the highest acceptable value, the highest acceptable value is used. |
| INT upsSmartConfigSensitivity | 1.3.6.1.4.1.935.1.1.1.5.2.7 | INTEGER | read-write | The sensitivity of the UPS to utility line abnormalities or noises. |
| INT upsSmartConfigSetEEPROMDefaults | 1.3.6.1.4.1.935.1.1.1.5.2.12 | INTEGER | read-write | WRITE: Resets the UPS EEPROM variables to default values. READ: returns 0 |
| INT upsSmartConfigShutoffDelay | 1.3.6.1.4.1.935.1.1.1.5.2.10 | INTEGER | read-write | The delay in seconds the UPS remains on after being told to turn off. Allowed values are 12, 18, 24, 30, 36, 42, 48, 54, 60, 120, 180, 240, 300, 360, 420, 480, 540, and 600 seconds. If a value other than a supported value is provided in a set request, the UPS interprets it as next higher acceptable value. If the provided value is higher than the highest acceptable value, the highest acceptable value is used. |
| INT upsSmartConfigUpsSleepTime | 1.3.6.1.4.1.935.1.1.1.5.2.11 | INTEGER | read-write | The time in minutes for the UPS to go to 'sleep' when instructed. When in sleep mode, the UPS will not provide output power regardless of the input line state. Once the specified time has elapsed, output power will be restored. This is a configuration setting. The UPS will not go to sleep until told to do so by the manager from a management station. Any input value is allowed, however the UPS only recognizes 0 - 9999 minutes in one minute increments. If the provided value is higher than the highest acceptable value, the highest acceptable value is used. |
| upsSmartControl | 1.3.6.1.4.1.935.1.1.1.6.2 | |||
| INT upsSmartControlFlashAndBeep | 1.3.6.1.4.1.935.1.1.1.6.2.5 | INTEGER | read-write | UPS to identify itself by lighting all indicators and beeping. Setting this variable to FlashAndBeep(2) causes the UPS lights all panel indicators and beeps. Setting this value to noFlashAndBeep(1) has no effect. The value noFlashAndBeep(1) will always be returned when the variable is read. |
| INT upsSmartControlRebootUps | 1.3.6.1.4.1.935.1.1.1.6.2.2 | INTEGER | read-write | Setting this variable to rebootUps(2) causes the UPS to shut off and turn back on. Setting this value to noRebootUps(1) has no effect. The value noRebootUps(1) will always be returned when the variable is read. |
| INT upsSmartControlSimulatePowerFail | 1.3.6.1.4.1.935.1.1.1.6.2.4 | INTEGER | read-write | Setting this variable to simulatePowerFailure(2) causes the UPS switch to battery power. Setting this value to noSimulatePowerFailure(1) has no effect. The value noSimulatePowerFailure(1) will always be returned when the variable is read. |
| INT upsSmartControlTurnOnUpsLoad | 1.3.6.1.4.1.935.1.1.1.6.2.6 | INTEGER | read-write | Setting this variable to upsSmartControlTurnOnUpsLoad(2) causes the UPS switch back to utility power if utility power is present. Setting this value to noUpsSmartControlTurnOnUpsLoad(1) has no effect. The value noUpsSmartControlTurnOnUpsLoad(1) will always be returned when the variable is read. |
| INT upsSmartControlUpsOff | 1.3.6.1.4.1.935.1.1.1.6.2.1 | INTEGER | read-write | Setting this variable to turnUpsOff(2) causes the UPS to shut off. When in this state, the UPS will not provide output power regardless of the input line state. The on/off switch on the UPS must be toggled for the UPS to return to operation. Setting this value to noTurnUpsOff(1) has no effect. The value noTurnUpsOff(1) will always be returned when the variable is read. |
| INT upsSmartControlUpsSleep | 1.3.6.1.4.1.935.1.1.1.6.2.3 | INTEGER | read-write | Setting this variable to putUpsToSleep(2) causes the UPS to go to sleep for the time specified by upsSmartConfigUpsSleepTime. When in sleep mode, the UPS will not provide output power regardless of the input line state. Once the specified time has elapsed, output power will be restored. Setting this value to noPutUpsToSleep(1) has no effect. The value noPutUpsToSleep(1) will always be returned when the variable is read. |
| upsSmartIdent | 1.3.6.1.4.1.935.1.1.1.1.2 | |||
| STR upsSmartIdentAgentFirmwareRevision | 1.3.6.1.4.1.935.1.1.1.1.2.4 | DisplayString | read-only | The firmware revision of the UPS SNMP Proxy agent. |
| STR upsSmartIdentDateOfManufacture | 1.3.6.1.4.1.935.1.1.1.1.2.2 | DisplayString | read-only | The date when the UPS was manufactured in mm/dd/yy format. |
| STR upsSmartIdentFirmwareRevision | 1.3.6.1.4.1.935.1.1.1.1.2.1 | DisplayString | read-only | The firmware revision of the UPS system. |
| STR upsSmartIdentUpsSerialNumber | 1.3.6.1.4.1.935.1.1.1.1.2.3 | DisplayString | read-only | An 8-character string identifying the serial number of the UPS internal microprocessor. This number is set at the factory. NOTE: This number does NOT correspond to the serial number on the rear of the UPS. |
| upsSmartInput | 1.3.6.1.4.1.935.1.1.1.3.2 | |||
| INT upsSmartInputFrequency | 1.3.6.1.4.1.935.1.1.1.3.2.4 | INTEGER | read-only | The current input frequency to the UPS system in 1/10 Hz. |
| INT upsSmartInputLineFailCause | 1.3.6.1.4.1.935.1.1.1.3.2.5 | INTEGER | read-only | The reason for the occurrence of the last transfer to UPS battery power. The variable is set to noTransfer(1) if there is no transfer yet. The variable is set to highLineVoltage(2) if the transfer to battery is caused by an over voltage greater than the high transfer voltage. The variable is set to brownout(3) if the duration of the outage is greater than five seconds and the line voltage is between 40 percent of the rated output voltage and the low transfer voltage. The variable is set to blackout(4) if the duration of the outage is greater than five seconds and the line voltage is between 40 percent of the rated output voltage and ground. The variable is set to smallMomentarySag(5) if the duration of the outage is less than five seconds and the line voltage is between 40 percent of the rated output voltage and the low transfer voltage. The variable is set to deepMomentarySag(6) if the duration of the outage is less than five seconds and the line voltage is between 40 percent of the rated output voltage and ground. |
| INT upsSmartInputLineVoltage | 1.3.6.1.4.1.935.1.1.1.3.2.1 | INTEGER | read-only | The current utility line voltage in 1/10 VAC. |
| INT upsSmartInputMaxLineVoltage | 1.3.6.1.4.1.935.1.1.1.3.2.2 | INTEGER | read-only | The maximum utility line voltage in 1/10 VAC over the previous 1 minute period. |
| INT upsSmartInputMinLineVoltage | 1.3.6.1.4.1.935.1.1.1.3.2.3 | INTEGER | read-only | The minimum utility line voltage in 1/10 VAC over the previous 1 minute period. |
| upsSmartOutput | 1.3.6.1.4.1.935.1.1.1.4.2 | |||
| INT upsSmartOutputFrequency | 1.3.6.1.4.1.935.1.1.1.4.2.2 | INTEGER | read-only | The current output frequency of the UPS system in 1/10 Hz. |
| INT upsSmartOutputLoad | 1.3.6.1.4.1.935.1.1.1.4.2.3 | INTEGER | read-only | The current UPS load expressed in percent of rated capacity. |
| INT upsSmartOutputVoltage | 1.3.6.1.4.1.935.1.1.1.4.2.1 | INTEGER | read-only | The output voltage of the UPS system in 1/10 VAC. |
| upsSmartTest | 1.3.6.1.4.1.935.1.1.1.7.2 | |||
| STR upsSmartTestCalibrationDate | 1.3.6.1.4.1.935.1.1.1.7.2.8 | DisplayString | read-only | The date the last UPS runtime calibration was performed in mm/dd/yy format. |
| INT upsSmartTestCalibrationResults | 1.3.6.1.4.1.935.1.1.1.7.2.7 | INTEGER | read-only | The results of the last runtime calibration. Value ok(1) means a successful runtime calibration. Value invalidTest(2) indicates last calibration did not take place since the battery capacity was below 100 percent. Value calibrationInProgress(3) means a calibration is occurring now. |
| INT upsSmartTestDiagnostics | 1.3.6.1.4.1.935.1.1.1.7.2.2 | INTEGER | read-write | Setting this variable to testDiagnostics(2) causes the UPS to perform a diagnostic self test. Setting this value to noTestDiagnostics(1) has no effect. The value noTestDiagnostics(1) will always be returned when the variable is read. |
| INT upsSmartTestDiagnosticSchedule | 1.3.6.1.4.1.935.1.1.1.7.2.1 | INTEGER | read-write | The UPS system's automatic battery test schedule. |
| INT upsSmartTestDiagnosticsResults | 1.3.6.1.4.1.935.1.1.1.7.2.3 | INTEGER | read-only | The results of the last UPS diagnostics test performed. |
| INT upsSmartTestIndicators | 1.3.6.1.4.1.935.1.1.1.7.2.5 | INTEGER | read-write | Setting this variable to testIndicators(2) causes the UPS to perform a front panel indicator (lights) test. Setting this value to noTestIndicators(1) has no effect. The value noTestIndicators(1) will always be returned when the variable is read. |
| STR upsSmartTestLastDiagnosticsDate | 1.3.6.1.4.1.935.1.1.1.7.2.4 | DisplayString | read-only | The date the last UPS diagnostics test was performed in mm/dd/yy format. |
| INT upsSmartTestRuntimeCalibration | 1.3.6.1.4.1.935.1.1.1.7.2.6 | INTEGER | read-write | Setting this variable to performCalibration(2) causes the UPS to discharge to calibrate the UPS. The test will only start if the battery capacity is 100 percent. The test runs until capacity is less than 25 percent. Setting this variable to cancelCurrentCalibration(3) after setting performCalibration(2) will cancel the current discharge. Setting this variable to noPerformCalibration(1) will have no effect. The value noPerformCalibration(1) will always be returned when the variable is read. The result of the calibration will be saved in upsSmartTestCalibrationResult. |
| NTF upsTemp | 1.3.6.1.4.1.935.0.27 | WARNING: UPS Temperature Overrun | ||
| NTF upsTempNormal | 1.3.6.1.4.1.935.0.29 | WARNING: UPS temperature Normal | ||
| NTF upsTest | 1.3.6.1.4.1.935.0.51 | WARNING: UPS Test | ||
| upsTestp | 1.3.6.1.4.1.935.1.1.1.7 | |||
| upsThreePhase | 1.3.6.1.4.1.935.1.1.1.8 | |||
| INT upsThreePhaseBatteryCapacityPercentage | 1.3.6.1.4.1.935.1.1.1.8.1.2 | INTEGER | read-only | Battery Capacity Percentage |
| INT upsThreePhaseBatteryCurrent | 1.3.6.1.4.1.935.1.1.1.8.1.4 | INTEGER | read-only | Battery Electric Current |
| upsThreePhaseBatteryGrp | 1.3.6.1.4.1.935.1.1.1.8.1 | |||
| INT upsThreePhaseBatteryTemperature | 1.3.6.1.4.1.935.1.1.1.8.1.5 | INTEGER | read-only | Battery Temperature |
| INT upsThreePhaseBatteryTimeRemain | 1.3.6.1.4.1.935.1.1.1.8.1.3 | INTEGER | read-only | Battery Time Remain (unit is Minute) |
| INT upsThreePhaseBatteryVoltage | 1.3.6.1.4.1.935.1.1.1.8.1.1 | INTEGER | read-only | Battery Voltage |
| upsThreePhaseBypassGrp | 1.3.6.1.4.1.935.1.1.1.8.4 | |||
| INT upsThreePhaseBypassSourceFrequency | 1.3.6.1.4.1.935.1.1.1.8.4.1 | INTEGER | read-only | Bypass Frequency |
| INT upsThreePhaseBypssSourceVoltageR | 1.3.6.1.4.1.935.1.1.1.8.4.2 | INTEGER | read-only | Bypass VoltageR |
| INT upsThreePhaseBypssSourceVoltageS | 1.3.6.1.4.1.935.1.1.1.8.4.3 | INTEGER | read-only | Bypass VoltageS |
| INT upsThreePhaseBypssSourceVoltageT | 1.3.6.1.4.1.935.1.1.1.8.4.4 | INTEGER | read-only | Bypass VoltageT |
| INT upsThreePhaseDCandRectifierStatusBatteryStatus | 1.3.6.1.4.1.935.1.1.1.8.5.5 | INTEGER | read-only | Back Status |
| INT upsThreePhaseDCandRectifierStatusChargeStatus | 1.3.6.1.4.1.935.1.1.1.8.5.6 | INTEGER | read-only | Charge Status |
| upsThreePhaseDCandRectifierStatusGrp | 1.3.6.1.4.1.935.1.1.1.8.5 | |||
| INT upsThreePhaseDCandRectifierStatusInAndOut | 1.3.6.1.4.1.935.1.1.1.8.5.4 | INTEGER | read-only | In And Put |
| INT upsThreePhaseDCandRectifierStatusLowBattery | 1.3.6.1.4.1.935.1.1.1.8.5.3 | INTEGER | read-only | Low Battery |
| INT upsThreePhaseDCandRectifierStatusLowBatteryShutdown | 1.3.6.1.4.1.935.1.1.1.8.5.2 | INTEGER | read-only | Low Battery Shutdown |
| INT upsThreePhaseDCandRectifierStatusRecOperating | 1.3.6.1.4.1.935.1.1.1.8.5.7 | INTEGER | read-only | Rectifier Operating |
| INT upsThreePhaseDCandRectifierStatusRecRotError | 1.3.6.1.4.1.935.1.1.1.8.5.1 | INTEGER | read-only | Rectifier Rotation Error |
| INT upsThreePhaseFaultStatusBypassBreaker | 1.3.6.1.4.1.935.1.1.1.8.7.3 | INTEGER | read-only | Bypass Breaker |
| INT upsThreePhaseFaultStatusEmergencyStop | 1.3.6.1.4.1.935.1.1.1.8.7.1 | INTEGER | read-only | Emergency Stop |
| upsThreePhaseFaultStatusGrp | 1.3.6.1.4.1.935.1.1.1.8.7 | |||
| INT upsThreePhaseFaultStatusHighDCShutdown | 1.3.6.1.4.1.935.1.1.1.8.7.2 | INTEGER | read-only | High DC Shutdown |
| INT upsThreePhaseFaultStatusInverterOutputFail | 1.3.6.1.4.1.935.1.1.1.8.7.5 | INTEGER | read-only | Output Fail |
| INT upsThreePhaseFaultStatusOverLoad | 1.3.6.1.4.1.935.1.1.1.8.7.4 | INTEGER | read-only | Over Load |
| INT upsThreePhaseFaultStatusOverTemperature | 1.3.6.1.4.1.935.1.1.1.8.7.6 | INTEGER | read-only | Over Temperature |
| INT upsThreePhaseFaultStatusShortCircuit | 1.3.6.1.4.1.935.1.1.1.8.7.7 | INTEGER | read-only | Short Circuit |
| INT upsThreePhaseInputFrequency | 1.3.6.1.4.1.935.1.1.1.8.2.1 | INTEGER | read-only | Input Frequency |
| upsThreePhaseInputGrp | 1.3.6.1.4.1.935.1.1.1.8.2 | |||
| INT upsThreePhaseInputVoltageR | 1.3.6.1.4.1.935.1.1.1.8.2.2 | INTEGER | read-only | Input VoltageR |
| INT upsThreePhaseInputVoltageS | 1.3.6.1.4.1.935.1.1.1.8.2.3 | INTEGER | read-only | Input VoltageS |
| INT upsThreePhaseInputVoltageT | 1.3.6.1.4.1.935.1.1.1.8.2.4 | INTEGER | read-only | Input VoltageT |
| INT upsThreePhaseOutputFrequency | 1.3.6.1.4.1.935.1.1.1.8.3.1 | INTEGER | read-only | Output Frequency |
| upsThreePhaseOutputGrp | 1.3.6.1.4.1.935.1.1.1.8.3 | |||
| INT upsThreePhaseOutputLoadPercentageR | 1.3.6.1.4.1.935.1.1.1.8.3.5 | INTEGER | read-only | Load PercentageR |
| INT upsThreePhaseOutputLoadPercentageS | 1.3.6.1.4.1.935.1.1.1.8.3.6 | INTEGER | read-only | Load PercentageS |
| INT upsThreePhaseOutputLoadPercentageT | 1.3.6.1.4.1.935.1.1.1.8.3.7 | INTEGER | read-only | Load PercentageT |
| INT upsThreePhaseOutputVoltageR | 1.3.6.1.4.1.935.1.1.1.8.3.2 | INTEGER | read-only | Output VoltageR |
| INT upsThreePhaseOutputVoltageS | 1.3.6.1.4.1.935.1.1.1.8.3.3 | INTEGER | read-only | Output VoltageS |
| INT upsThreePhaseOutputVoltageT | 1.3.6.1.4.1.935.1.1.1.8.3.4 | INTEGER | read-only | Output VoltageT |
| INT upsThreePhaseRatingBatteryVoltage | 1.3.6.1.4.1.935.1.1.1.8.8.7 | INTEGER | read-only | Battery Voltage |
| INT upsThreePhaseRatingBypassFrequency | 1.3.6.1.4.1.935.1.1.1.8.8.4 | INTEGER | read-only | Bypass Frequency |
| STR upsThreePhaseRatingBypassVoltage | 1.3.6.1.4.1.935.1.1.1.8.8.3 | DisplayString | read-only | Bypass Voltage |
| upsThreePhaseRatingGrp | 1.3.6.1.4.1.935.1.1.1.8.8 | |||
| INT upsThreePhaseRatingOutputFrequency | 1.3.6.1.4.1.935.1.1.1.8.8.6 | INTEGER | read-only | Output Frequency |
| STR upsThreePhaseRatingOutputVoltage | 1.3.6.1.4.1.935.1.1.1.8.8.5 | DisplayString | read-only | Output Voltage |
| STR upsThreePhaseRatingPower | 1.3.6.1.4.1.935.1.1.1.8.8.8 | DisplayString | read-only | Power Rating |
| INT upsThreePhaseRatingRectifierFrequency | 1.3.6.1.4.1.935.1.1.1.8.8.2 | INTEGER | read-only | Rectifier Frequency |
| STR upsThreePhaseRatingRectifierVoltage | 1.3.6.1.4.1.935.1.1.1.8.8.1 | DisplayString | read-only | Rectifier Voltage |
| INT upsThreePhaseUPSStaticSwitchMode | 1.3.6.1.4.1.935.1.1.1.8.6.4 | INTEGER | read-only | Switch Mode |
| INT upsThreePhaseUPSStatusACStatus | 1.3.6.1.4.1.935.1.1.1.8.6.3 | INTEGER | read-only | AC Status |
| INT upsThreePhaseUPSStatusBypassFreqFail | 1.3.6.1.4.1.935.1.1.1.8.6.1 | INTEGER | read-only | Bypass Status |
| upsThreePhaseUPSStatusGrp | 1.3.6.1.4.1.935.1.1.1.8.6 | |||
| INT upsThreePhaseUPSStatusInverterOperating | 1.3.6.1.4.1.935.1.1.1.8.6.5 | INTEGER | read-only | Operating |
| INT upsThreePhaseUPSStatusManualBypassBreaker | 1.3.6.1.4.1.935.1.1.1.8.6.2 | INTEGER | read-only | Breaker Status |
| NTF upsTurnedOff | 1.3.6.1.4.1.935.0.12 | WARNING: The UPS has been turned 'off' by the management station. | ||
| NTF upsWokeUp | 1.3.6.1.4.1.935.0.14 | INFORMATION: The UPS woke up from 'sleep' mode. Power to the load has been restored. | ||
| INT vaRatingOfDevice | 1.3.6.1.4.1.935.1.1.1.5.1.2.1.3 | INTEGER | read-write | The volt-amp rating of the device plugged into the UPS. |
RFC description
Extreme Networks XPPC (eXtreme Performance Package for Core) MIB; manages switch performance, line cards, and fabric modules.
Start monitoring Vendor UPS/power-management appliance, PPC product line (trap-receiver config, UPS model/firmware status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.