Wellfleet-CCTOPTS-MIB

All MIBs › Wellfleet-CCTOPTS-MIB

Category: Wellfleet BayNetworks System Management

Description: Defines Wellfleet circuit configuration options including line parameters and protocol encapsulation settings.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-CCTOPTS-MIB?

This is a vendor-specific proprietary MIB from Wellfleet Communications (later Bay Networks/Nortel) defining circuit configuration options for its multiprotocol routers, including per-circuit line parameters and protocol encapsulation settings. It is primarily a configuration MIB rather than a counter MIB, exposing how each WAN or LAN circuit is provisioned at the link layer. It supports software status monitoring in that the configured encapsulation and line parameters determine whether a circuit can establish and maintain protocol-level connectivity, so mismatches here are a common root cause of circuits that are physically up but functionally down. It is part of Wellfleet's broader proprietary circuit ('wfCct') MIB hierarchy and depends on that base circuit addressing scheme rather than any external standard. It is typically deployed alongside other Wellfleet circuit-level MIBs on routers terminating serial, Frame Relay, or leased-line WAN circuits. Engineers can download the Wellfleet-CCTOPTS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-CCTOPTS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet/Bay Networks multiprotocol routers with WAN circuit interfaces

Monitoring Examples

No sample_objects were provided for this module; based on the short_desc, an operator would review the circuit's configured encapsulation type and line parameters (e.g., clocking, framing) against the expected values for the far-end device. A circuit reporting physical line-up but failing to pass traffic often traces back to an encapsulation mismatch (e.g., HDLC vs. Frame Relay) visible in this MIB's configuration objects.

What Can Be Monitored

circuit line parameter configuration
protocol encapsulation type
circuit enable/disable status

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress

From RFC1213-MIB

DisplayString

From Wellfleet-COMMON-MIB

wfCircuitOptsGroup

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfCctOptsTable	1.3.6.1.4.1.18.3.5.1.4.1		not-accessible	The table of circuit names
wfCctOptsEntry	1.3.6.1.4.1.18.3.5.1.4.1.1		not-accessible	Entry format for the table of circuit options
INT wfCctOptsDelete	1.3.6.1.4.1.18.3.5.1.4.1.1.1	INTEGER	read-write	Creation and deletion flag for this record
INT wfCctOptsPriorityQueueingDisable	1.3.6.1.4.1.18.3.5.1.4.1.1.2	INTEGER	read-write	Priority Queuing option
INT wfCctOptsCct	1.3.6.1.4.1.18.3.5.1.4.1.1.3	INTEGER	read-only	circuit number
INT wfCctOptsHighPriorityQueueLimit	1.3.6.1.4.1.18.3.5.1.4.1.1.4	INTEGER	read-write	High Priority Queue limit The minimum valid value is zero. no maximum valid value (limited by bufs for the slot)
INT wfCctOptsNormalPriorityQueueLimit	1.3.6.1.4.1.18.3.5.1.4.1.1.5	INTEGER	read-write	Normal Priority Queue limit The minimum valid value is zero. no maximum valid value (limited by bufs for the slot)
INT wfCctOptsLowPriorityQueueLimit	1.3.6.1.4.1.18.3.5.1.4.1.1.6	INTEGER	read-write	Low Priority Queue limit The minimum valid value is zero. no maximum valid value (limited by bufs for the slot)
INT wfCctOptsMaxInterruptQueueLatency	1.3.6.1.4.1.18.3.5.1.4.1.1.7	INTEGER	read-write	Interrupt Queue Latency
INT wfCctOptsMaxHighPriorityQueueLatency	1.3.6.1.4.1.18.3.5.1.4.1.1.8	INTEGER	read-write	High Priority Queue Latency
CTR wfCctOptsHiXmits	1.3.6.1.4.1.18.3.5.1.4.1.1.9	Counter	read-only	High Priority Transmit count
CTR wfCctOptsNormalXmits	1.3.6.1.4.1.18.3.5.1.4.1.1.10	Counter	read-only	Normal Priority Transmit count
CTR wfCctOptsLoXmits	1.3.6.1.4.1.18.3.5.1.4.1.1.11	Counter	read-only	Low Priority Transmit count
CTR wfCctOptsHiClippedPkts	1.3.6.1.4.1.18.3.5.1.4.1.1.12	Counter	read-only	High Prio Transmit Clip Count
CTR wfCctOptsNormalClippedPkts	1.3.6.1.4.1.18.3.5.1.4.1.1.13	Counter	read-only	Normal Prio Transmit Clip Count
CTR wfCctOptsLoClippedPkts	1.3.6.1.4.1.18.3.5.1.4.1.1.14	Counter	read-only	Low Prio Transmit Clip Count
GAU wfCctOptsIntrQHighWaterPkts	1.3.6.1.4.1.18.3.5.1.4.1.1.15	Gauge	read-only	Interrupt Queue high-water mark
GAU wfCctOptsHiQHighWaterPkts	1.3.6.1.4.1.18.3.5.1.4.1.1.16	Gauge	read-only	High-priority Queue high-water mark
GAU wfCctOptsNormalQHighWaterPkts	1.3.6.1.4.1.18.3.5.1.4.1.1.17	Gauge	read-only	Normal Queue high-water mark
GAU wfCctOptsLoQHighWaterPkts	1.3.6.1.4.1.18.3.5.1.4.1.1.18	Gauge	read-only	Low-priority Queue high-water mark
INT wfCctOptsHighWaterPktsClear	1.3.6.1.4.1.18.3.5.1.4.1.1.19	INTEGER	read-write	Attribute to clear the high-water marks. When the MIB changes, Priority Queueing (if ENABLED) checks to see if HighWaterPktsClear is different than the last time the MIB was modified in any way. If it is different, all the high water marks (see above) are set to zero.
CTR wfCctOptsDroppedPkts	1.3.6.1.4.1.18.3.5.1.4.1.1.20	Counter	read-only	Packets which were filtered in Priority Queueing
CTR wfCctOptsLargePkts	1.3.6.1.4.1.18.3.5.1.4.1.1.21	Counter	read-only	Large Packets which became an exception to latency rules
CTR wfCctOptsRxPkts	1.3.6.1.4.1.18.3.5.1.4.1.1.22	Counter	read-only	Packets received
INT wfCctOptsChooserType	1.3.6.1.4.1.18.3.5.1.4.1.1.23	INTEGER	read-write	Algorithm to choose line within a multiline circuit
INT wfCctOptsPqDequeueAlgType	1.3.6.1.4.1.18.3.5.1.4.1.1.24	INTEGER	read-write	Selection of Priority Queueing dequeueing algorithm PQ_STRICT_PRIORITIZATION is 'classical' 7.50 dequeueing. PQ_BANDWIDTH_ALLOCATION makes exceptions to strict prioritization in order to prevent starvation of the Normal and/or Low priority traffic.
INT wfCctOptsHiPercent	1.3.6.1.4.1.18.3.5.1.4.1.1.25	INTEGER	read-write	This is the percent of the SYNC line bandwidth that the network manager wishes to allocate to traffic which has been configured to be High Priority. This parameter only has meaning when the bandwidth allocation dequeueing algorithm is enabled by setting the dequeueing algorithm type appropriately. With this parameter set other than 100, each time the configured percent utilization is reached, Normal and Low traffic is sent out (if any is queued up), up to their configured percentages.
INT wfCctOptsNormalPercent	1.3.6.1.4.1.18.3.5.1.4.1.1.26	INTEGER	read-write	The minimum percent of the SYNC line that Normal-priority traffic will get (if there is any) when the Bandwidth Allocation feature is enabled. See text for wfCctOptsHiPercent for more information.
INT wfCctOptsLoPercent	1.3.6.1.4.1.18.3.5.1.4.1.1.27	INTEGER	read-write	The minimum percent of the SYNC line that Low-priority traffic will get (if there is any) when the Bandwidth Allocation feature is enabled. See text for wfCctOptsHiPercent for more information.
CTR wfCctOptsHiTotalOctets	1.3.6.1.4.1.18.3.5.1.4.1.1.28	Counter	read-only	Running total of High Octets transmitted when using Bandwidth Allocation dequeueing algorithm
CTR wfCctOptsNormalTotalOctets	1.3.6.1.4.1.18.3.5.1.4.1.1.29	Counter	read-only	Running total of Normal Octets transmitted when using Bandwidth Allocation dequeueing algorithm
CTR wfCctOptsLoTotalOctets	1.3.6.1.4.1.18.3.5.1.4.1.1.30	Counter	read-only	Running total of Low Octets transmitted when using Bandwidth Allocation dequeueing algorithm
INT wfCctOptsCircuitType	1.3.6.1.4.1.18.3.5.1.4.1.1.31	INTEGER	read-write	Circuit Type Attribute
INT wfCctOptsBackupCct	1.3.6.1.4.1.18.3.5.1.4.1.1.32	INTEGER	read-write	backup circuit number
INT wfCctOptsPrimaryCctWanProtocolType	1.3.6.1.4.1.18.3.5.1.4.1.1.33	INTEGER	read-write	The type of WAN protocol type which is running on the primary line. This attribute is only read when a dial backup circuit is using this mib record.
INT wfCctOptsMacFilterFormat	1.3.6.1.4.1.18.3.5.1.4.1.1.34	INTEGER	read-write	Used to force the Mac src/dst address to be matched in Token Ring format.
CTR wfCctOptsPktsNotQueued	1.3.6.1.4.1.18.3.5.1.4.1.1.35	Counter	read-only	Packets that were not Queued or Dropped by Priority Queuing
INT wfCctOptsBitsShiftCount	1.3.6.1.4.1.18.3.5.1.4.1.1.36	INTEGER	read-write	Used to shift src/dst address to the right when addressed based chooser is set.
INT wfCctOptsFrSetDeLowQ	1.3.6.1.4.1.18.3.5.1.4.1.1.37	INTEGER	read-write	Used on Frame Relay interfaces, allows Set of DE ( Discard Eligible ) bit of packets that end up in PQ's Low Queue, the Default is Do Set DE bit
INT wfCctOptsFrSetDeNormQ	1.3.6.1.4.1.18.3.5.1.4.1.1.38	INTEGER	read-write	Used on Frame Relay interfaces, allows Set of DE ( Discard Eligible ) bit of packets that end up in PQ's Normal Queue, the Default is Don't Set DE bit
INT wfCctOptsShapedPriorityQueueLimit	1.3.6.1.4.1.18.3.5.1.4.1.1.39	INTEGER	read-write	Frame Relay Traffic Shaping Priority Queue Limit. the minimum valid value is zerom no maximum valid value (limited by bufs for the slot).
INT wfCctOptsMaxShapedPriorityQueueLatency	1.3.6.1.4.1.18.3.5.1.4.1.1.40	INTEGER	read-write	Frame Relay Traffic Shaping Priority Queue Latency.
CTR wfCctOptsShapedXmits	1.3.6.1.4.1.18.3.5.1.4.1.1.41	Counter	read-only	Frame Relay Traffic Shaping Priority Transmit count.
CTR wfCctOptsShapedClippedPkts	1.3.6.1.4.1.18.3.5.1.4.1.1.42	Counter	read-only	Frame Relay Traffic Shaping Transmit Clip count.
GAU wfCctOptsShapedQHighWaterPkts	1.3.6.1.4.1.18.3.5.1.4.1.1.43	Gauge	read-only	Frame Relay Traffic Shaping Queue high-water mark.
CTR wfCctOptsShapedTotalOctets	1.3.6.1.4.1.18.3.5.1.4.1.1.44	Counter	read-only	Running total of Frame Relay Traffic Shaping octets transmitted.
INT wfCctOptsPpqDebugLevel	1.3.6.1.4.1.18.3.5.1.4.1.1.45	INTEGER	read-write	Protocol Priority Queueing Debug Level.
INT wfDequeueAtLineRate	1.3.6.1.4.1.18.3.5.1.4.1.1.46	INTEGER	read-write	Determines whether the dequeuing from the queues is to be done at the line rate instead of the conventional technique or not.
wfCctOptsBrFilterTable	1.3.6.1.4.1.18.3.5.1.4.2		not-accessible	Bridge Filters
wfCctOptsBrFilterEntry	1.3.6.1.4.1.18.3.5.1.4.2.1		not-accessible	An entry in WfCctOptsBrFilterTable.
INT wfCctOptsBrFilterCreate	1.3.6.1.4.1.18.3.5.1.4.2.1.1	INTEGER	read-write	Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
INT wfCctOptsBrFilterEnable	1.3.6.1.4.1.18.3.5.1.4.2.1.2	INTEGER	read-write	Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
INT wfCctOptsBrFilterState	1.3.6.1.4.1.18.3.5.1.4.2.1.3	INTEGER	read-only	Defines the current State of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
CTR wfCctOptsBrFilterCounter	1.3.6.1.4.1.18.3.5.1.4.2.1.4	Counter	read-only	The number of received packets that have matched this rule.
OCT wfCctOptsBrFilterDefinition	1.3.6.1.4.1.18.3.5.1.4.2.1.5	OCTET STRING	read-write	The filter rule definition.
INT wfCctOptsBrFilterReserved	1.3.6.1.4.1.18.3.5.1.4.2.1.6	INTEGER	read-only	Reserved field.
INT wfCctOptsBrFilterCct	1.3.6.1.4.1.18.3.5.1.4.2.1.7	INTEGER	read-only	The ID of the CctBridge Cct to which the filter is applied.
INT wfCctOptsBrFilterRuleNumber	1.3.6.1.4.1.18.3.5.1.4.2.1.8	INTEGER	read-only	ID for the rule.
INT wfCctOptsBrFilterFragment	1.3.6.1.4.1.18.3.5.1.4.2.1.9	INTEGER	read-only	Fragment number - for large rules.
STR wfCctOptsBrFilterName	1.3.6.1.4.1.18.3.5.1.4.2.1.10	DisplayString	read-write	name of the rule number
wfCctOptsIpFilterTable	1.3.6.1.4.1.18.3.5.1.4.3		not-accessible	Ip Filters
wfCctOptsIpFilterEntry	1.3.6.1.4.1.18.3.5.1.4.3.1		not-accessible	An entry in WfCctOptsIpFilterTable.
INT wfCctOptsIpFilterCreate	1.3.6.1.4.1.18.3.5.1.4.3.1.1	INTEGER	read-write	Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
INT wfCctOptsIpFilterEnable	1.3.6.1.4.1.18.3.5.1.4.3.1.2	INTEGER	read-write	Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
INT wfCctOptsIpFilterState	1.3.6.1.4.1.18.3.5.1.4.3.1.3	INTEGER	read-only	Defines the current State of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
CTR wfCctOptsIpFilterCounter	1.3.6.1.4.1.18.3.5.1.4.3.1.4	Counter	read-only	The number of received packets that have matched this rule.
OCT wfCctOptsIpFilterDefinition	1.3.6.1.4.1.18.3.5.1.4.3.1.5	OCTET STRING	read-write	The filter rule definition.
INT wfCctOptsIpFilterReserved	1.3.6.1.4.1.18.3.5.1.4.3.1.6	INTEGER	read-only	Reserved field.
INT wfCctOptsIpFilterCct	1.3.6.1.4.1.18.3.5.1.4.3.1.7	INTEGER	read-only	The ID of the CctIp Cct to which the filter is applied.
INT wfCctOptsIpFilterRuleNumber	1.3.6.1.4.1.18.3.5.1.4.3.1.8	INTEGER	read-only	ID for the rule.
INT wfCctOptsIpFilterFragment	1.3.6.1.4.1.18.3.5.1.4.3.1.9	INTEGER	read-only	Fragment number - for large rules.
STR wfCctOptsIpFilterName	1.3.6.1.4.1.18.3.5.1.4.3.1.10	DisplayString	read-write	name of the rule number
wfCctOptsLengthBasedTable	1.3.6.1.4.1.18.3.5.1.4.4		not-accessible	Length Based Priority Table
wfCctOptsLengthBasedEntry	1.3.6.1.4.1.18.3.5.1.4.4.1		not-accessible	An entry in WfCctOptsLengthBasedTable.
INT wfCctOptsLengthBasedDelete	1.3.6.1.4.1.18.3.5.1.4.4.1.1	INTEGER	read-write	Defines the existence of the length based priority filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
INT wfCctOptsLengthBasedDisable	1.3.6.1.4.1.18.3.5.1.4.4.1.2	INTEGER	read-write	Defines whether or not the length based priority filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
INT wfCctOptsLengthBasedState	1.3.6.1.4.1.18.3.5.1.4.4.1.3	INTEGER	read-only	Defines the current State of the length based priority filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
INT wfCctOptsLengthBasedCct	1.3.6.1.4.1.18.3.5.1.4.4.1.4	INTEGER	read-only	The ID of the Cct to which the filter is applied
INT wfCctOptsLengthBasedMux	1.3.6.1.4.1.18.3.5.1.4.4.1.5	INTEGER	read-only	packet mux type
OCT wfCctOptsLengthBasedData	1.3.6.1.4.1.18.3.5.1.4.4.1.6	OCTET STRING	read-only	a five byte quantity of the form ethernet - 0x6003000000 (e.g. DECnet) lsap - 0xfefe030000 (e.g. OSI) snap - 0x0000000800 (e.g. IP) - 0x0800070800 (e.g. Appletalk DDP)
INT wfCctOptsLengthBasedLength	1.3.6.1.4.1.18.3.5.1.4.4.1.7	INTEGER	read-write	Maximum length of a packet to be considered high priority
INT wfCctOptsLengthBasedLessThanQ	1.3.6.1.4.1.18.3.5.1.4.4.1.8	INTEGER	read-write	queue into which packets of length less than or equal wfCctOptsLengthBasedLength are placed
INT wfCctOptsLengthBasedGreaterThanQ	1.3.6.1.4.1.18.3.5.1.4.4.1.9	INTEGER	read-write	queue into which packets of length greater than wfCctOptsLengthBasedLength are placed
wfSwservOptsTable	1.3.6.1.4.1.18.3.5.1.4.5		not-accessible	The table of circuits defined over switched services
wfSwservOptsEntry	1.3.6.1.4.1.18.3.5.1.4.5.1		not-accessible	Entry format for the table of sw_serv circuit options
INT wfSwservOptsDelete	1.3.6.1.4.1.18.3.5.1.4.5.1.1	INTEGER	read-write	Creation and deletion flag
INT wfSwservOptsCct	1.3.6.1.4.1.18.3.5.1.4.5.1.2	INTEGER	read-only	Circuit Number
INT wfSwservOptsCircuitType	1.3.6.1.4.1.18.3.5.1.4.5.1.3	INTEGER	read-write	Circuit Type Attribute
INT wfSwservOptsBackupCct	1.3.6.1.4.1.18.3.5.1.4.5.1.4	INTEGER	read-write	Backup Circuit Number assigned by site manager
INT wfSwservOptsBackupPool	1.3.6.1.4.1.18.3.5.1.4.5.1.5	INTEGER	read-write	Backup Pool Id
INT wfSwservOptsDemandPool	1.3.6.1.4.1.18.3.5.1.4.5.1.6	INTEGER	read-write	Dial on Demand Pool Id
INT wfSwservOptsBackupMode	1.3.6.1.4.1.18.3.5.1.4.5.1.7	INTEGER	read-write	Mode Master ( initiate dialing ) or Slave
INT wfSwservOptsActiveBackupCct	1.3.6.1.4.1.18.3.5.1.4.5.1.8	INTEGER	read-write	Active Backup Indicator
INT wfSwservOptsForcedDial	1.3.6.1.4.1.18.3.5.1.4.5.1.9	INTEGER	read-write	Forced Dial Indicator
INT wfSwservOptsMaxUpTime	1.3.6.1.4.1.18.3.5.1.4.5.1.10	INTEGER	read-write	Max amount fo time dial call can exist
INT wfSwservOptsBringUpHour	1.3.6.1.4.1.18.3.5.1.4.5.1.11	INTEGER	read-write	Time of day hour to allow a line to dial
INT wfSwservOptsBringUpMinute	1.3.6.1.4.1.18.3.5.1.4.5.1.12	INTEGER	read-write	Time of day minute to allow a line to dial
INT wfSwservOptsTakeDownHour	1.3.6.1.4.1.18.3.5.1.4.5.1.13	INTEGER	read-write	Time of day hour to take down a dial line
INT wfSwservOptsTakeDownMinute	1.3.6.1.4.1.18.3.5.1.4.5.1.14	INTEGER	read-write	Time of day minute to take down a dial line
INT wfSwservOptsInactivityTime	1.3.6.1.4.1.18.3.5.1.4.5.1.15	INTEGER	read-write	Maximum for inactivity timer is equal to infinity = 99999999
INT wfSwservOptsCircuitState	1.3.6.1.4.1.18.3.5.1.4.5.1.16	INTEGER	read-only	Circuit State
INT wfSwservOptsPrimaryDownTime	1.3.6.1.4.1.18.3.5.1.4.5.1.17	INTEGER	read-write	Amount of time allowed for establishment of primary before the backup is invoked
CTR wfSwservOptsNumOutgoingConn	1.3.6.1.4.1.18.3.5.1.4.5.1.18	Counter	read-only	Number of Outgoing call attempts for this circuit
CTR wfSwservOptsNumIncomingConn	1.3.6.1.4.1.18.3.5.1.4.5.1.19	Counter	read-only	Number of Incoming call attempts for this circuit
INT wfSwservOptsActiveSlot	1.3.6.1.4.1.18.3.5.1.4.5.1.20	INTEGER	read-only	Slot actively in use by this call
INT wfSwservOptsActiveLine	1.3.6.1.4.1.18.3.5.1.4.5.1.21	INTEGER	read-only	Line actively in use by this call
CTR wfSwservOptsPacketsDropped	1.3.6.1.4.1.18.3.5.1.4.5.1.22	Counter	read-only	Number of Incoming call attempts for this circuit
INT wfSwservOptsTimeLastPktDropped	1.3.6.1.4.1.18.3.5.1.4.5.1.23	INTEGER	read-only	Number of Incoming call attempts for this circuit
INT wfSwservOptsForcedTakedown	1.3.6.1.4.1.18.3.5.1.4.5.1.24	INTEGER	read-write	Forced Dial Indicator
INT wfSwservOptsRetryMax	1.3.6.1.4.1.18.3.5.1.4.5.1.25	INTEGER	read-write	Redial count
CTR wfSwservOptsRetryCount	1.3.6.1.4.1.18.3.5.1.4.5.1.26	Counter	read-only	Redial count
INT wfSwservOptsRetryDelay	1.3.6.1.4.1.18.3.5.1.4.5.1.27	INTEGER	read-write	delay to wait after retrys fails. value is in seconds
INT wfSwservOptsDemandConnectionMode	1.3.6.1.4.1.18.3.5.1.4.5.1.28	INTEGER	read-write	Mode Master - outgoing call has precedence terminate incoming call Slave - incoming call has precedence terminate outgoing call NO_Dial - if data is present do MOT establish connection just drop the data
INT wfSwservOptsAutoDemandTermination	1.3.6.1.4.1.18.3.5.1.4.5.1.29	INTEGER	read-write	Automatically terminates demand circuit if maximum connect attempts reached
INT wfSwservOptsAutoDemandTermReset	1.3.6.1.4.1.18.3.5.1.4.5.1.30	INTEGER	read-write	Amount of time ( in Minutes )before atttempting to recreate the demand circuit after an auto termination
STR wfSwservOptsChapLocalName	1.3.6.1.4.1.18.3.5.1.4.5.1.31	DisplayString	read-write	This attribute is used to assign a local CHAP Name to outbound calls to to inform our peer of our identity, during WHOAMI processing
STR wfSwservOptsChapSecret	1.3.6.1.4.1.18.3.5.1.4.5.1.32	DisplayString	read-write	Secret used for running CHAP when this cct is active. The peer must use the same secret when responding to our Challenges, which will be found in the Whoami Table
INT wfSwservOptsMaxUpTermination	1.3.6.1.4.1.18.3.5.1.4.5.1.33	INTEGER	read-write	Automatically terminates demand circuit if maximum connect attempts reached
INT wfSwservOptsMaxUpTermReset	1.3.6.1.4.1.18.3.5.1.4.5.1.34	INTEGER	read-write	Amount of time ( in Minutes )before atttempting to recreate the demand circuit after an auto termination
INT wfSwservOptsBandwidthPool	1.3.6.1.4.1.18.3.5.1.4.5.1.35	INTEGER	read-write	Bandwidth on Demand Pool Id
INT wfSwservOptsBandwidthMode	1.3.6.1.4.1.18.3.5.1.4.5.1.36	INTEGER	read-write	Bandwidth Mode Monitor (Congestion Monitor) or NORMAL
STR wfSwservOptsPapId	1.3.6.1.4.1.18.3.5.1.4.5.1.37	DisplayString	read-write	This attribute is used to assign a local PAP Id to outbound calls to to inform our peer of our identity, during WHOAMI processing
STR wfSwservOptsPapPassword	1.3.6.1.4.1.18.3.5.1.4.5.1.38	DisplayString	read-write	This attribute is used to assign a local PAP Password to outbound calls to to inform our peer of our identity, during WHOAMI processing
INT wfSwservOptsDebugMsgLevel	1.3.6.1.4.1.18.3.5.1.4.5.1.39	INTEGER	read-write	This attribute is used to assign the level of Swserv Debug message to be logged for the circuit
INT wfSwservOptsDmdCctGroupNum	1.3.6.1.4.1.18.3.5.1.4.5.1.40	INTEGER	read-write	Backup Circuit Number assigned by site manager
INT wfSwservOptsWanProtocol	1.3.6.1.4.1.18.3.5.1.4.5.1.41	INTEGER	read-write	Wan Protocol for this circuit assigned by site manager. Used by BNX Software to Support ISDN Switched access to Frame Relay Switch Network.
INT wfSwservOptsSecondaryCct	1.3.6.1.4.1.18.3.5.1.4.5.1.42	INTEGER	read-write	Secondary circuit to be used by Line Manager when creating a backup for this primary circuit.
INT wfSwservOptsPoolLineNumber	1.3.6.1.4.1.18.3.5.1.4.5.1.43	INTEGER	read-write	Pooling line number used for identifying Frame Relay backup interface objects associated with a pool.
INT wfSwservOptsPoolLineIndex	1.3.6.1.4.1.18.3.5.1.4.5.1.44	INTEGER	read-write	Lower layer index used for identifying Frame Relay backup interface objects associated with a pool.
INT wfSwservOptsMinDuration	1.3.6.1.4.1.18.3.5.1.4.5.1.45	INTEGER	read-write	Maximum for min duration timer in seconds is equal to infinity = 99999999, min is 10
INT wfSwservOptsInactivityMode	1.3.6.1.4.1.18.3.5.1.4.5.1.46	INTEGER	read-write	Inactivity check mode
INT wfSwservOptsOpportunityRouting	1.3.6.1.4.1.18.3.5.1.4.5.1.47	INTEGER	read-write	OpportunityRouting Indicator
INT wfSwservOptsOutboundAuth	1.3.6.1.4.1.18.3.5.1.4.5.1.48	INTEGER	read-write	Allows the disabling of Authentication when the router is placing an outbound call.
INT wfSwservOptsOverSubRetryTimer	1.3.6.1.4.1.18.3.5.1.4.5.1.49	INTEGER	read-write	This parameter allows the user to cofigure the time period at which a connection will be retried, if a previous connection attempt for routing updates failed due to lack of line resources. This time should be less than the stabilization timer for IP/IPX protocols. This time is expressed in minutes and is meaningful only if Dial Optimized Routing is enabled.
INT wfSwservOptsStandbyMode	1.3.6.1.4.1.18.3.5.1.4.5.1.50	INTEGER	read-write	This parameter allows a demand circuit to be identified as standby or demand. The hot standby circuit is down until an event invokes it. Normal standby is invoked manually or by an incoming call.
INT wfSwservOptsStandbyFailBackMode	1.3.6.1.4.1.18.3.5.1.4.5.1.51	INTEGER	read-write	This parameter is used to indicate if standby failback should be automatic or manual.
INT wfSwservOptsManualStandbyAction	1.3.6.1.4.1.18.3.5.1.4.5.1.52	INTEGER	read-write	This parameter is used to manually activate and deactivate a standby circuit.
INT wfSwservOptsCallbackMode	1.3.6.1.4.1.18.3.5.1.4.5.1.53	INTEGER	read-write	Defines the role this circuit will play in Callback. INACTIVE disables Callback on this circuit. SERVER performs Callback via Outgoing Phone Number. CLIENT circuit expects peer to perform Callback. SERVER_CALLID performs Callback via ANI
INT wfSwservOptsCallbackServerDelay	1.3.6.1.4.1.18.3.5.1.4.5.1.54	INTEGER	read-write	The amount of time the CALLBACK_SERVER will wait, (in seconds) before performing Callback,dialing back the initial caller. The default time is 0, however modem connections may need some delay configured to prevent busy situations.
INT wfSwservOptsCallbackClientDelay	1.3.6.1.4.1.18.3.5.1.4.5.1.55	INTEGER	read-write	The amount of time the CALLBACK_CLIENT will wait, (in seconds) for its peer to perform Callback. Data ariving during opperation of the timer, will not cause a connection to be established.
INT wfSwservOptsQueueSize	1.3.6.1.4.1.18.3.5.1.4.5.1.56	INTEGER	read-write	This parameter controls the length of the queue used for dial services.
INT wfSwservOptsDequeueWaitTimer	1.3.6.1.4.1.18.3.5.1.4.5.1.57	INTEGER	read-write	This parameter controls the time FR waits before dequeuing data for FRDOD.
INT wfSwservOptsMru	1.3.6.1.4.1.18.3.5.1.4.5.1.58	INTEGER	read-write	This is the MRU being used for this demand circuit.
INT wfSwservOptsRfc1661Compliance	1.3.6.1.4.1.18.3.5.1.4.5.1.59	INTEGER	read-write	Enable/disable RFC 1661 compliance
INT wfSwservOptsBootupDelay	1.3.6.1.4.1.18.3.5.1.4.5.1.60	INTEGER	read-write	Delay in initiation of the DoD circuit at bootup time
INT wfSwservOptsCallbackOptRfc1570	1.3.6.1.4.1.18.3.5.1.4.5.1.61	INTEGER	read-write	The PPP/LCP Callback Option; indicates the type of data content the callback client places in wfSwservOptsCallbackDataRfc1570 for the callback server
STR wfSwservOptsCallbackDataRfc1570	1.3.6.1.4.1.18.3.5.1.4.5.1.62	DisplayString	read-write	The PPP/LCP Callback Data; the actual callback client data which is sent to the callback server for processing
wfSwservOutPhoneNumTable	1.3.6.1.4.1.18.3.5.1.4.6		not-accessible	*************************************** SWSERV outgoing phone number list
wfSwservOutPhoneNumEntry	1.3.6.1.4.1.18.3.5.1.4.6.1		not-accessible	An entry in the SWSERV_SYNC table
INT wfSwservOutPhoneNumDelete	1.3.6.1.4.1.18.3.5.1.4.6.1.1	INTEGER	read-write	Delete this phone number from the list
INT wfSwservOutPhoneNumCct	1.3.6.1.4.1.18.3.5.1.4.6.1.2	INTEGER	read-only	CCT number for this phone list instance
INT wfSwservOutPhoneNumIndex	1.3.6.1.4.1.18.3.5.1.4.6.1.3	INTEGER	read-only	a unique one up type number to create a list
STR wfSwservOutPhoneNumRmtStationNum	1.3.6.1.4.1.18.3.5.1.4.6.1.4	DisplayString	read-write	the station address (phone number) of the remote system
STR wfSwservOutPhoneNumSubAddr	1.3.6.1.4.1.18.3.5.1.4.6.1.5	DisplayString	read-write	for Swserv phone numbers, the sub address portion
STR wfSwservOutPhoneNumDelimiter	1.3.6.1.4.1.18.3.5.1.4.6.1.6	DisplayString	read-write	for Swserv phone numbers, the delimiter portion
INT wfSwservOutPhoneNumType	1.3.6.1.4.1.18.3.5.1.4.6.1.7	INTEGER	read-write	phone number types; ISDN types, Modem Sync Dial or Async Dial types
INT wfSwservOutPhoneNumTypeofNum	1.3.6.1.4.1.18.3.5.1.4.6.1.8	INTEGER	read-write	IF ISDN type number, it needs type of number UNKNOWN Type is 0, use 1 to satisfy MDL requirement This attribute value will be ANDED with 0xFFF0 before using it.
INT wfSwservOutPhoneNumPlan	1.3.6.1.4.1.18.3.5.1.4.6.1.9	INTEGER	read-write	If Isdn and if type of number is UNKNOWN or INERNATIONAL or NATIONAL or SUBSCRIBER then a plan number is needed. UNKNOWN is 0 , using 16 (0x10)to satisfy MDL requirement. We will AND this field with 0x0F before using it.
INT wfSwservOutPhoneNumRateAdaption	1.3.6.1.4.1.18.3.5.1.4.6.1.10	INTEGER	read-write	If Isdn and if a specifis Transfer rate is to be requested when establishing a call to this distination address specify the desired rate.
INT wfSwservOutPhoneNumRemotePoolType	1.3.6.1.4.1.18.3.5.1.4.6.1.11	INTEGER	read-write	Specify the types of calls accepted by the remote router on this port. For example, if the port on the remote router resides in only a demand pool specify the port type for this phone number to be dialondemand.
INT wfSwservOutPhoneNumConnectionType	1.3.6.1.4.1.18.3.5.1.4.6.1.12	INTEGER	read-write	Specify if this phone number can be used to receive a single call or multiple calls.
INT wfSwservOutPhoneNumChannelType	1.3.6.1.4.1.18.3.5.1.4.6.1.13	INTEGER	read-write	Type of Channels used for the outgoing call.
INT wfSwservOutPhoneNumAggrChanCnt	1.3.6.1.4.1.18.3.5.1.4.6.1.14	INTEGER	read-write	Multiplier for the Multirate call.
STR wfSwservOutPhoneNumPrefix	1.3.6.1.4.1.18.3.5.1.4.6.1.15	DisplayString	read-write	Phone number prefix such as hayes dial command.
INT wfSwservOutPhoneNumBearerService	1.3.6.1.4.1.18.3.5.1.4.6.1.16	INTEGER	read-write	The Bearer service - data or voice, for ISDN call setup using this number
wfSwservInPhoneNumTable	1.3.6.1.4.1.18.3.5.1.4.7		not-accessible	SWSERV Ingoing phone number list
wfSwservInPhoneNumEntry	1.3.6.1.4.1.18.3.5.1.4.7.1		not-accessible	An entry in the Swserv_SYNC table
INT wfSwservInPhoneNumDelete	1.3.6.1.4.1.18.3.5.1.4.7.1.1	INTEGER	read-write	Delete this phone number from the list
INT wfSwservInPhoneNumIndex	1.3.6.1.4.1.18.3.5.1.4.7.1.2	INTEGER	read-only	a unique one up type number to create a list
STR wfSwservInPhoneNumRmtStationNum	1.3.6.1.4.1.18.3.5.1.4.7.1.3	DisplayString	read-write	the station address (phone number) of the remote system
STR wfSwservInPhoneNumSubAddr	1.3.6.1.4.1.18.3.5.1.4.7.1.4	DisplayString	read-write	for Swserv phone numbers, the sub address portion
STR wfSwservInPhoneNumDelimiter	1.3.6.1.4.1.18.3.5.1.4.7.1.5	DisplayString	read-write	for Swserv phone numbers, the delimiter portion
INT wfSwservInPhoneNumType	1.3.6.1.4.1.18.3.5.1.4.7.1.6	INTEGER	read-write	phone number types; ISDN types or Modem Dial types
INT wfSwservInPhoneNumTypeofNum	1.3.6.1.4.1.18.3.5.1.4.7.1.7	INTEGER	read-write	We will AND this field with 0x0xFFF0 before using it.
INT wfSwservInPhoneNumPlan	1.3.6.1.4.1.18.3.5.1.4.7.1.8	INTEGER	read-write	0x0F before using it.
INT wfSwservInPhoneNumCct	1.3.6.1.4.1.18.3.5.1.4.7.1.9	INTEGER	read-write	Identifies which circuit should be used when performing Callback. If Null, Authentication must complete before Callback can occur.
wfCctOptsBrBuPppFilterTable	1.3.6.1.4.1.18.3.5.1.4.8		not-accessible	Dial Backup PPP Datalink filter table
wfCctOptsBrBuPppFilterEntry	1.3.6.1.4.1.18.3.5.1.4.8.1		not-accessible	An entry in WfCctOptsBrBuPppFilterTable.
INT wfCctOptsBrBuPppFilterCreate	1.3.6.1.4.1.18.3.5.1.4.8.1.1	INTEGER	read-write	Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
INT wfCctOptsBrBuPppFilterEnable	1.3.6.1.4.1.18.3.5.1.4.8.1.2	INTEGER	read-write	Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
INT wfCctOptsBrBuPppFilterState	1.3.6.1.4.1.18.3.5.1.4.8.1.3	INTEGER	read-only	Defines the current State of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
CTR wfCctOptsBrBuPppFilterCounter	1.3.6.1.4.1.18.3.5.1.4.8.1.4	Counter	read-only	The number of received packets that have matched this rule.
OCT wfCctOptsBrBuPppFilterDefinition	1.3.6.1.4.1.18.3.5.1.4.8.1.5	OCTET STRING	read-write	The filter rule definition.
INT wfCctOptsBrBuPppFilterReserved	1.3.6.1.4.1.18.3.5.1.4.8.1.6	INTEGER	read-only	Reserved field.
INT wfCctOptsBrBuPppFilterCct	1.3.6.1.4.1.18.3.5.1.4.8.1.7	INTEGER	read-only	The ID of the CctBridge Cct to which the filter is applied.
INT wfCctOptsBrBuPppFilterRuleNumber	1.3.6.1.4.1.18.3.5.1.4.8.1.8	INTEGER	read-only	ID for the rule.
INT wfCctOptsBrBuPppFilterFragment	1.3.6.1.4.1.18.3.5.1.4.8.1.9	INTEGER	read-only	Fragment number - for large rules.
STR wfCctOptsBrBuPppFilterName	1.3.6.1.4.1.18.3.5.1.4.8.1.10	DisplayString	read-write	name of the rule number
wfCctOptsIpBuPppFilterTable	1.3.6.1.4.1.18.3.5.1.4.9		not-accessible	IP Filter Table for Backup Lines
wfCctOptsIpBuPppFilterEntry	1.3.6.1.4.1.18.3.5.1.4.9.1		not-accessible	An entry in WfCctOptsIpBuPppFilterTable.
INT wfCctOptsIpBuPppFilterCreate	1.3.6.1.4.1.18.3.5.1.4.9.1.1	INTEGER	read-write	Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
INT wfCctOptsIpBuPppFilterEnable	1.3.6.1.4.1.18.3.5.1.4.9.1.2	INTEGER	read-write	Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
INT wfCctOptsIpBuPppFilterState	1.3.6.1.4.1.18.3.5.1.4.9.1.3	INTEGER	read-only	Defines the current State of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
CTR wfCctOptsIpBuPppFilterCounter	1.3.6.1.4.1.18.3.5.1.4.9.1.4	Counter	read-only	The number of received packets that have matched this rule.
OCT wfCctOptsIpBuPppFilterDefinition	1.3.6.1.4.1.18.3.5.1.4.9.1.5	OCTET STRING	read-write	The filter rule definition.
INT wfCctOptsIpBuPppFilterReserved	1.3.6.1.4.1.18.3.5.1.4.9.1.6	INTEGER	read-only	Reserved field.
INT wfCctOptsIpBuPppFilterCct	1.3.6.1.4.1.18.3.5.1.4.9.1.7	INTEGER	read-only	The ID of the CctBridge Cct to which the filter is applied.
INT wfCctOptsIpBuPppFilterRuleNumber	1.3.6.1.4.1.18.3.5.1.4.9.1.8	INTEGER	read-only	ID for the rule.
INT wfCctOptsIpBuPppFilterFragment	1.3.6.1.4.1.18.3.5.1.4.9.1.9	INTEGER	read-only	Fragment number - for large rules.
STR wfCctOptsIpBuPppFilterName	1.3.6.1.4.1.18.3.5.1.4.9.1.10	DisplayString	read-write	name of the rule number
wfCctOptsCngcTable	1.3.6.1.4.1.18.3.5.1.4.10		not-accessible	BNX Switch congestion control Table
wfCctOptsCngcEntry	1.3.6.1.4.1.18.3.5.1.4.10.1		not-accessible	An entry in WfCctOptsCngcTable.
INT wfCctOptsCngcDelete	1.3.6.1.4.1.18.3.5.1.4.10.1.1	INTEGER	read-write	Defines the existence of the congestion control entry CNGC_CREATED - congestion control entry exists CNGC_DELETED - congestion control entry does not exist and can be deleted.
INT wfCctOptsCngcDisable	1.3.6.1.4.1.18.3.5.1.4.10.1.2	INTEGER	read-write	Defines whether congestion control is enabled or disabled on the circuit
INT wfCctOptsCngcCct	1.3.6.1.4.1.18.3.5.1.4.10.1.3	INTEGER	read-only	The circuit number of the circuit to which the entry is applied
INT wfCctOptsCngcSmdsDiscardability	1.3.6.1.4.1.18.3.5.1.4.10.1.4	INTEGER	read-write	This is obsolete in V5.0 and upwards. Defines how SMDS packets entering BNX network through SMDS SSI and SMDS SNI interfaces should be treated at this circuit during congestion for dropping. This is applicable only on the internodal links. CNGC_FRDE - treat this like Frame relay DE frame. CNGC_FRNDE - treat this like Frame Relay non DE frame CNGC_DATAGRAM - treat this like a datagram packet.
INT wfCctOptsCngcCfgSwtxqThreshold	1.3.6.1.4.1.18.3.5.1.4.10.1.5	INTEGER	read-write	This is obsolete in V5.0 and upwards. Defines the user configured software transmit queue threshold. If this is set to NULL_VAL then the switch calculates the default value depending on the media and uses the default value. The default value is recommended.
INT wfCctOptsCngcSwtxqThreshold	1.3.6.1.4.1.18.3.5.1.4.10.1.6	INTEGER	read-only	This is obsolete in V5.0 and upwards. Defines the software transmit queue threshold in use. Switch updates this attribute to inform user what the current software transmit queue threshold is.
INT wfCctOptsCngcCngLevel0Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.7	INTEGER	read-write	This is obsolete in V5.0 and upwards. Defines the Software Transmit Queue congestion level 0 threshold as a percentage of the Software Transmit Queue Threshold. The default value is recommended.
INT wfCctOptsCngcCngLevel1Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.8	INTEGER	read-write	This is obsolete in V5.0 and upwards. Defines the Software Transmit Queue congestion level 1 threshold as a percentage of the Software Transmit Queue Threshold. The default value is recommended. wfCctOptsCngcCngLevel1Threshold should be more than wfCctOptsCngcCngLevel0Threshold, otherwise there will be no congestion level 1.
INT wfCctOptsCngcCngLevel2Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.9	INTEGER	read-write	This is obsolete in V5.0 and upwards. Defines the Software Transmit Queue congestion level 2 threshold as a percentage of the Software Transmit Queue Threshold. The default value is recommended. wfCctOptsCngcCngLevel2Threshold should be more than wfCctOptsCngcCngLevel1Threshold, otherwise there will be no congestion level 2.
INT wfCctOptsCngcLinkType	1.3.6.1.4.1.18.3.5.1.4.10.1.10	INTEGER	read-write	Defines whether the circuit is an access link or inter-nodal link (trunk). Traffic monitoring, traffic priority determination, traffic discardability level determination are done at access link and each incoming packet on an access link is tagged with the information. Inter-nodal link (trunk) uses the above tagged information in packets for priority queueing and discarding packets during congestion. WARNING - It is important to set the appropriate link type for this attribute otherwise congestion control will not work. The default value for this attribute is access link. This attribute value must be changed to CNGC_LINK_INTER_NODAL for inter-nodal link(trunk).
INT wfCctOptsCngcTrfPriorityEnable	1.3.6.1.4.1.18.3.5.1.4.10.1.11	INTEGER	read-write	Defines whether traffic prioritization is enabled or disabled on the circuit.
INT wfCctOptsCngcPortIPTrfPriority	1.3.6.1.4.1.18.3.5.1.4.10.1.12	INTEGER	read-write	Defines the traffic priority for transmitting Non Frame Relay or SMDS traffic on this port. CNGC_IPPRIORITY_TWO - Default Value Set all non FR or SMDS user traffic packets to priority 2. CNGC_IPPRIORITY_ONE - Set all non FR or SMDS packets to priority 1. CNGC_IPPRIORITY_TWO - Set all non FR or SMDS packets to priority 2. CNGC_IPPRIORITY_THREE - Set all non FR or SMDS packets to priority 3.
INT wfCctOptsCngcPortTrfDiscardLvl	1.3.6.1.4.1.18.3.5.1.4.10.1.13	INTEGER	read-write	Defines at what congestion level the incoming packets on this port should be discarded in the network. CNGC_DISCARD_AT_LVL_TWO - Discard FR DE packets at level 2, discard FR non DE packets at level 4, discard SMDS packets at level 3, discard IP packets at level 3. Default value CNGC_DISCARD_AT_LVL_ONE - discard all at level 1 CNGC_DISCARD_AT_LVL_TWO - discard all at level 2 CNGC_DISCARD_AT_LVL_THREE - discard all at level 3 CNGC_DISCARD_AT_LVL_FOUR - discard all at level 4
INT wfCctOptsCngcPortTrfPriority	1.3.6.1.4.1.18.3.5.1.4.10.1.14	INTEGER	read-write	Defines the traffic priority level of all the incoming packets on this port. CNGC_PRIORITY_TWO - Default value Set all incoming user traffic packets to priority 2. CNGC_PRIORITY_ONE - Set all incoming packets to priority 1. CNGC_PRIORITY_TWO - Set all incoming packets to priority 2. CNGC_PRIORITY_THREE - Set all incoming packets to priority 3. Priority 0 is reserved for network critical packets like OSPF, FR LMI and SMDS heartbeat, Cross Net polling and is not available for user traffic.
INT wfCctOptsCngcCfgHwtxQThreshold	1.3.6.1.4.1.18.3.5.1.4.10.1.15	INTEGER	read-write	Defines the user configured hardware transmit queue threshold. NULL_VAL - Switch calculates the appropriate value based on system resources and uses the value. This is recommended. CNGC_HWTXQ_MINIMUM - minimum value to be used. CNGC_HWTXQ_MAXIMUM - maximum value to be used.
INT wfCctOptsCngcHwtxQThreshold	1.3.6.1.4.1.18.3.5.1.4.10.1.16	INTEGER	read-only	The current hardware queue threshold
INT wfCctOptsCngcSndTrapForPktsDropped	1.3.6.1.4.1.18.3.5.1.4.10.1.17	INTEGER	read-write	Switch sends a congestion notification trap for every wfCctOptsCngcSndTrapForPktsDropped number of packets dropped.
INT wfCctOptsCngcCfgQp0Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.18	INTEGER	read-write	Defines the Priority 0 queue threshold NULL_VAL - Switch calculates the appropriate value based on system resources and uses the value. This is recommended.
INT wfCctOptsCngcQp0Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.19	INTEGER	read-only	current Priority 0 queue threshold
INT wfCctOptsCngcQp0CngLvl0Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.20	INTEGER	read-write	Defines priority 0 queue congestion level 0 threshold as a percentage of priority 0 queue threshold.
INT wfCctOptsCngcQp0CngLvl1Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.21	INTEGER	read-write	Defines priority 0 queue congestion level 1 threshold as a percentage of priority 0 queue threshold. The value of this attribute should be greater than wfCctOptsCngcQp0CngLvl0Threshold, otherwise there will be no priority 0 queue congestion level 1.
INT wfCctOptsCngcQp0CngLvl2Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.22	INTEGER	read-write	Defines priority 0 queue congestion level 2 threshold as a percentage of priority 0 queue threshold. The value of this attribute should be greater than wfCctOptsCngcQp0CngLvl1Threshold, otherwise there will be no priority 0 queue congestion level 2.
INT wfCctOptsCngcQp0PktsServPriNxtQ	1.3.6.1.4.1.18.3.5.1.4.10.1.23	INTEGER	read-write	Defines the number of priority 0 queue packets to be served prior to serving each priority 1 queue packet. If priority 0 queue is empty then priority 1 queue packets are served.
INT wfCctOptsCngcCfgQp1Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.24	INTEGER	read-write	Defines the Priority 1 queue threshold NULL_VAL - Switch calculates the appropriate value based on system resources and uses the value. This is recommended.
INT wfCctOptsCngcQp1Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.25	INTEGER	read-only	current Priority 0 queue threshold
INT wfCctOptsCngcQp1CngLvl0Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.26	INTEGER	read-write	Defines priority 1 queue congestion level 0 threshold as a percentage of priority 1 queue threshold.
INT wfCctOptsCngcQp1CngLvl1Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.27	INTEGER	read-write	Defines priority 1 queue congestion level 1 threshold as a percentage of priority 1 queue threshold. The value of this attribute should be greater than wfCctOptsCngcQp1CngLvl0Threshold, otherwise there will be no priority 1 queue congestion level 1.
INT wfCctOptsCngcQp1CngLvl2Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.28	INTEGER	read-write	Defines priority 1 queue congestion level 2 threshold as a percentage of priority 1 queue threshold. The value of this attribute should be greater than wfCctOptsCngcQp1CngLvl1Threshold, otherwise there will be no priority 1 queue congestion level 2.
INT wfCctOptsCngcQp1PktsServPriNxtQ	1.3.6.1.4.1.18.3.5.1.4.10.1.29	INTEGER	read-write	Defines the number of priority 1 queue packets to be served prior to serving each priority 2 queue packet. If priority 1 queue is empty then priority 2 queue packets are served.
INT wfCctOptsCngcCfgQp2Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.30	INTEGER	read-write	Defines the Priority 2 queue threshold NULL_VAL - Switch calculates the appropriate value based on system resources and uses the value. This is recommended.
INT wfCctOptsCngcQp2Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.31	INTEGER	read-only	current Priority 0 queue threshold
INT wfCctOptsCngcQp2CngLvl0Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.32	INTEGER	read-write	Defines priority 2 queue congestion level 0 threshold as a percentage of priority 2 queue threshold.
INT wfCctOptsCngcQp2CngLvl1Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.33	INTEGER	read-write	Defines priority 2 queue congestion level 1 threshold as a percentage of priority 2 queue threshold. The value of this attribute should be greater than wfCctOptsCngcQp2CngLvl0Threshold, otherwise there will be no priority 2 queue congestion level 1.
INT wfCctOptsCngcQp2CngLvl2Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.34	INTEGER	read-write	Defines priority 2 queue congestion level 2 threshold as a percentage of priority 2 queue threshold. The value of this attribute should be greater than wfCctOptsCngcQp2CngLvl1Threshold, otherwise there wil be no priority 2 queue congestion level 2.
INT wfCctOptsCngcQp2PktsServPriNxtQ	1.3.6.1.4.1.18.3.5.1.4.10.1.35	INTEGER	read-write	Defines the number of priority 2 queue packets to be served prior to serving each priority 3 queue packet. If priority 2 queue is empty then priority 3 queue packets are served.
INT wfCctOptsCngcCfgQp3Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.36	INTEGER	read-write	Defines the Priority 3 queue threshold NULL_VAL - Switch calculates the appropriate value based on system resources and uses the value. This is recommended.
INT wfCctOptsCngcQp3Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.37	INTEGER	read-only	current Priority 3 queue threshold
INT wfCctOptsCngcQp3CngLvl0Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.38	INTEGER	read-write	Defines priority 3 queue congestion level 0 threshold as a percentage of priority 3 queue threshold.
INT wfCctOptsCngcQp3CngLvl1Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.39	INTEGER	read-write	Defines priority 3 queue congestion level 1 threshold as a percentage of priority 3 queue threshold. The value of this attribute should be greater than wfCctOptsCngcQp3CngLvl0Threshold, otherwise there will be no priority 3 queue congestion level 1.
INT wfCctOptsCngcQp3CngLvl2Threshold	1.3.6.1.4.1.18.3.5.1.4.10.1.40	INTEGER	read-write	Defines priority 3 queue congestion level 2 threshold as a percentage of priority 3 queue threshold. The value of this attribute should be greater than wfCctOptsCngcQp3CngLvl1Threshold, otherwise there will be no priority 3 queue congestion level 2.
CTR wfCctOptsCngcPriority0TxPkts	1.3.6.1.4.1.18.3.5.1.4.10.1.41	Counter	read-only	Number of priority 0 packets transmitted
CTR wfCctOptsCngcPriority0TxOctets	1.3.6.1.4.1.18.3.5.1.4.10.1.42	Counter	read-only	Number of priority 0 Octets transmitted
CTR wfCctOptsCngcPriority0DropPkts	1.3.6.1.4.1.18.3.5.1.4.10.1.43	Counter	read-only	Number of priority 0 packets dropped */
CTR wfCctOptsCngcPriority0DropOctets	1.3.6.1.4.1.18.3.5.1.4.10.1.44	Counter	read-only	Number of priority 0 octets dropped
CTR wfCctOptsCngcPriority1TxPkts	1.3.6.1.4.1.18.3.5.1.4.10.1.45	Counter	read-only	Number of priority 1 packets transmitted
CTR wfCctOptsCngcPriority1TxOctets	1.3.6.1.4.1.18.3.5.1.4.10.1.46	Counter	read-only	Number of priority 1 Octets transmitted
CTR wfCctOptsCngcPriority1DropPkts	1.3.6.1.4.1.18.3.5.1.4.10.1.47	Counter	read-only	Number of priority 1 packets dropped */
CTR wfCctOptsCngcPriority1DropOctets	1.3.6.1.4.1.18.3.5.1.4.10.1.48	Counter	read-only	Number of priority 1 octets dropped
CTR wfCctOptsCngcPriority2TxPkts	1.3.6.1.4.1.18.3.5.1.4.10.1.49	Counter	read-only	Number of priority 2 packets transmitted
CTR wfCctOptsCngcPriority2TxOctets	1.3.6.1.4.1.18.3.5.1.4.10.1.50	Counter	read-only	Number of priority 2 Octets transmitted
CTR wfCctOptsCngcPriority2DropPkts	1.3.6.1.4.1.18.3.5.1.4.10.1.51	Counter	read-only	Number of priority 2 packets dropped */
CTR wfCctOptsCngcPriority2DropOctets	1.3.6.1.4.1.18.3.5.1.4.10.1.52	Counter	read-only	Number of priority 2 octets dropped
CTR wfCctOptsCngcPriority3TxPkts	1.3.6.1.4.1.18.3.5.1.4.10.1.53	Counter	read-only	Number of priority 3 packets transmitted
CTR wfCctOptsCngcPriority3TxOctets	1.3.6.1.4.1.18.3.5.1.4.10.1.54	Counter	read-only	Number of priority 3 Octets transmitted
CTR wfCctOptsCngcPriority3DropPkts	1.3.6.1.4.1.18.3.5.1.4.10.1.55	Counter	read-only	Number of priority 3 packets dropped */
CTR wfCctOptsCngcPriority3DropOctets	1.3.6.1.4.1.18.3.5.1.4.10.1.56	Counter	read-only	Number of priority 3 octets dropped
CTR wfCctOptsCngcTxFRNonDePkts	1.3.6.1.4.1.18.3.5.1.4.10.1.57	Counter	read-only	Number of Frame Relay non DE packets transmitted
CTR wfCctOptsCngcTxFRNonDeOctets	1.3.6.1.4.1.18.3.5.1.4.10.1.58	Counter	read-only	Number of Frame Relay non DE octets transmitted
CTR wfCctOptsCngcTxFRDePkts	1.3.6.1.4.1.18.3.5.1.4.10.1.59	Counter	read-only	Number of Frame Relay DE packets transmitted
CTR wfCctOptsCngcTxFRDeOctets	1.3.6.1.4.1.18.3.5.1.4.10.1.60	Counter	read-only	Number of Frame Relay DE octets transmitted
CTR wfCctOptsCngcDropFRNonDePkts	1.3.6.1.4.1.18.3.5.1.4.10.1.61	Counter	read-only	Number of Frame Relay non DE packets dropped
CTR wfCctOptsCngcDropFRNonDeOctets	1.3.6.1.4.1.18.3.5.1.4.10.1.62	Counter	read-only	number of Frame Relay non DE octets dropped
CTR wfCctOptsCngcDropFRDePkts	1.3.6.1.4.1.18.3.5.1.4.10.1.63	Counter	read-only	number of Frame Relay DE packets dropped
CTR wfCctOptsCngcDropFRDeOctets	1.3.6.1.4.1.18.3.5.1.4.10.1.64	Counter	read-only	number of Frame Relay DE octets dropped
CTR wfCctOptsCngcFRSetFecnPkts	1.3.6.1.4.1.18.3.5.1.4.10.1.65	Counter	read-only	number of Frame Relay packets in which this link set FECN
CTR wfCctOptsCngcFRSetFecnOctets	1.3.6.1.4.1.18.3.5.1.4.10.1.66	Counter	read-only	number of Frame Relay octets in which this link set FECN
CTR wfCctOptsCngcFRSetBecnPkts	1.3.6.1.4.1.18.3.5.1.4.10.1.67	Counter	read-only	number of Frame Relay frames in which this link set BECN
CTR wfCctOptsCngcFRSetBecnOctets	1.3.6.1.4.1.18.3.5.1.4.10.1.68	Counter	read-only	number of Frame Relay octets in which this link set BECN
CTR wfCctOptsCngcDropNonFRPkts	1.3.6.1.4.1.18.3.5.1.4.10.1.69	Counter	read-only	Number of Non Frame Relay packets dropped
CTR wfCctOptsCngcDropNonFROctets	1.3.6.1.4.1.18.3.5.1.4.10.1.70	Counter	read-only	number of Non Frame Relay octets dropped
INT wfCctOptsCngcLogPower	1.3.6.1.4.1.18.3.5.1.4.10.1.71	INTEGER	read-write	This number specifies that the following log events: 1. Dropped DE Frame. 2. Dropped Non DE Frames. 3. Set DE Frames. 4. Set FECN/BECN. be logged once every (X) occurances. Where (X) = Base 2 raised to the power. The user specifies the power by setting this wfCctOptsCngcLogPower mib attribute. For example, setting wfCctOptsCngcLogPower to a value of 10 means that a log message will be logged once every 1024 occurances. 1024 = (2 ^ wfCctOptsCngcLogPower) or (2 raised to 10th power). Legal values for this attribute ranges from 10 to 31. This translates to 2^10 (1024) through 2^31 (2147483648). Default: 2^31.
wfSwservTODTable	1.3.6.1.4.1.18.3.5.1.4.11		not-accessible	SWSERV circuit time of day MIB
wfSwservTODEntry	1.3.6.1.4.1.18.3.5.1.4.11.1		not-accessible	An entry in the wfSwservTODTable
INT wfSwservTODDelete	1.3.6.1.4.1.18.3.5.1.4.11.1.1	INTEGER	read-write	Delete time of day instance from the list for this circuit
INT wfSwservTODCct	1.3.6.1.4.1.18.3.5.1.4.11.1.2	INTEGER	read-only	CCT number for time of day instance
INT wfSwservTODIndex	1.3.6.1.4.1.18.3.5.1.4.11.1.3	INTEGER	read-only	a unique number to specify instance
INT wfSwservTODType	1.3.6.1.4.1.18.3.5.1.4.11.1.4	INTEGER	read-write	Type of TOD Configuration
INT wfSwservTODStartTime	1.3.6.1.4.1.18.3.5.1.4.11.1.5	INTEGER	read-write	Start Time of day allow a line to dial ( HHMM format )
INT wfSwservTODEndTime	1.3.6.1.4.1.18.3.5.1.4.11.1.6	INTEGER	read-write	End Time of day connection can be active for specified circuit ( HHMM format )
INT wfSwservTODInactivityEnable	1.3.6.1.4.1.18.3.5.1.4.11.1.7	INTEGER	read-write	Inactivity Timer if disabled the inactivity timer is ignored during this time period, if enabled the connection is brought down due to inactivity. If this parameter is DISABLED, the circuit will be established automatically during the configured times, regardless of the Availability Mode.
INT wfSwservTODAvailabilityMode	1.3.6.1.4.1.18.3.5.1.4.11.1.8	INTEGER	read-write	Set this field to AVAILABLE to allow the circuit to be established between the configured start and end times. Set it to NOT AVAILABLE to prevent the circuit from being established during those times. Inactivity Timeout must be ENABLED for Availability Mode to have any effect. If Inactivity Timeout is DISABLED, the circuit will be established automatically during the configured times, regardless of the Availability Mode.
INT wfSwservTODStandbyFailBackMode	1.3.6.1.4.1.18.3.5.1.4.11.1.9	INTEGER	read-write	Indicates if failback mode for this time of day range. When set to automatic circuit will failback subject to the failback timer. When set to manual circuit will not failback.
INT wfSwservTODStandbyFailBackTime	1.3.6.1.4.1.18.3.5.1.4.11.1.10	INTEGER	read-write	Indicates number of minutes to wait after the primary is observed as active before deactivating the standby. Default value of 0 disables failback timer.
wfDemandCctGrpTable	1.3.6.1.4.1.18.3.5.1.4.12		not-accessible	The table of demand circuits groups defined over switched services
wfDemandCctGrpEntry	1.3.6.1.4.1.18.3.5.1.4.12.1		not-accessible	Entry format for the table of demand circuit group options
INT wfDmdCctGroupDelete	1.3.6.1.4.1.18.3.5.1.4.12.1.1	INTEGER	read-write	Creation and deletion flag
INT wfDmdCctGroupNum	1.3.6.1.4.1.18.3.5.1.4.12.1.2	INTEGER	read-only	Circuit Number
INT wfDmdCctGroupPoolId	1.3.6.1.4.1.18.3.5.1.4.12.1.3	INTEGER	read-only	Demand pool id used by this demand circuit group
INT wfDmdCctGroupNumofCcts	1.3.6.1.4.1.18.3.5.1.4.12.1.4	INTEGER	read-write	Demand pool id used by this demand circuit group
INT wfDmdCctGroupIPEnable	1.3.6.1.4.1.18.3.5.1.4.12.1.5	INTEGER	read-write	IP unnumbered enabled or disabled for specified demand circuit group
IP wfDmdCctGroupIPUnnumAssoc	1.3.6.1.4.1.18.3.5.1.4.12.1.6	IpAddress	read-write	The associated IP address used by unnumbered demand circuit group every demand circuit in this demand circuit group uses the same associated IP address.
INT wfDmdCctGroupRIPEnable	1.3.6.1.4.1.18.3.5.1.4.12.1.7	INTEGER	read-write	RIP enabled or disabled for specified demand circuit group
INT wfDmdCctGroupOSPFEnable	1.3.6.1.4.1.18.3.5.1.4.12.1.8	INTEGER	read-write	OSPF enabled or disabled for specified demand circuit group
INT wfDmdCctGroupIPXEnable	1.3.6.1.4.1.18.3.5.1.4.12.1.9	INTEGER	read-write	IPX unnumbered enabled or disabled for specified demand circuit group
INT wfDmdCctGroupBridgeEnable	1.3.6.1.4.1.18.3.5.1.4.12.1.10	INTEGER	read-write	Bridge enabled or disabled for specified demand circuit group
OCT wfDmdCctGroupCctList	1.3.6.1.4.1.18.3.5.1.4.12.1.11	OCTET STRING	read-write	List of demand circuits that are members of this group
INT wfDmdCctGroupIPXRouting	1.3.6.1.4.1.18.3.5.1.4.12.1.12	INTEGER	read-write	IPX routing protocol used for specified demand circuit group
INT wfDmdCctGroupIPXWANEnable	1.3.6.1.4.1.18.3.5.1.4.12.1.13	INTEGER	read-write	IPXWAN enabled or disabled for specified demand circuit group
INT wfDmdCctGroupRadiusEnable	1.3.6.1.4.1.18.3.5.1.4.12.1.14	INTEGER	read-write	Radius enabled or disabled for specified demand circuit group

RFC description

Circuit options MIB for Wellfleet routers providing priority queue management and traffic shaping configuration.

Start monitoring Wellfleet/Bay Networks multiprotocol routers with WAN circuit interfaces (line/encapsulation config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-CCTOPTS-MIB

What Is Wellfleet-CCTOPTS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description