| OID symbolic | OID numeric | Type | Access | Description |
|---|
| wfBot | 1.3.6.1.4.1.18.3.5.18.1 | | | |
| INT wfBotDelete | 1.3.6.1.4.1.18.3.5.18.1.1 | INTEGER | read-write | Create/Delete parameter. Default is created.
User perform an SNMP SET operation on this object
in order to create/delete BOT |
| INT wfBotDisable | 1.3.6.1.4.1.18.3.5.18.1.2 | INTEGER | read-write | Enable/Disable parameter. Default is enabled.
User perform an SNMP SET operation on this object
in order to enable/disable BOT |
| INT wfBotState | 1.3.6.1.4.1.18.3.5.18.1.3 | INTEGER | read-only | The current state of BOT |
| wfBotInterfaceTable | 1.3.6.1.4.1.18.3.5.18.2 | | not-accessible | Interface table which lists all BISYNC line entries and other
line related information |
| wfBotInterfaceEntry | 1.3.6.1.4.1.18.3.5.18.2.1 | | not-accessible | An entry in wfBotInterfaceTable |
| INT wfBotInterfaceDelete | 1.3.6.1.4.1.18.3.5.18.2.1.1 | INTEGER | read-write | Create/Delete attribute. Default is Created
Users perform SNMP SET operation on this object in
order to create/delete a translation interface record |
| INT wfBotInterfaceDisable | 1.3.6.1.4.1.18.3.5.18.2.1.2 | INTEGER | read-write | Enables/Disables this mapping entry
Setting of this attribute to DISABLED will disconnect
all active sessions pertaining to this interface entry |
| INT wfBotInterfaceCctNumber | 1.3.6.1.4.1.18.3.5.18.2.1.3 | INTEGER | read-only | The circuit from which the connection attempt is
received that initiates a translation session. |
| INT wfBotInterfaceSlotNumber | 1.3.6.1.4.1.18.3.5.18.2.1.4 | INTEGER | read-only | Slot number on which this interface is running |
| INT wfBotInterfaceState | 1.3.6.1.4.1.18.3.5.18.2.1.5 | INTEGER | read-only | The current state of the Interface |
| INT wfBotInterfaceType | 1.3.6.1.4.1.18.3.5.18.2.1.6 | INTEGER | read-write | If this interface is point-to-point, i.e. no splitting
occours we can straight away deliver BSC frame to designated
TCP circuit, without looking into the CU address |
| INT wfBotInterfaceAttachedTo | 1.3.6.1.4.1.18.3.5.18.2.1.7 | INTEGER | read-write | Information that this interface is attached to the Primary or
secondary BSC station |
| CTR wfBotInterfacePktCnt | 1.3.6.1.4.1.18.3.5.18.2.1.8 | Counter | read-only | Interface packet count ... |
| INT wfBotKeepaliveInterval | 1.3.6.1.4.1.18.3.5.18.2.1.9 | INTEGER | read-write | Idle session timeout period, in seconds. If an established
TCP connection remains inactive for this interval, KEEPALIVE
messages will be sent to the peer (if the Keepalive Timer is
non-zero). Setting the Idle Timer to zero disables the
keepalive feature. |
| INT wfBotKeepaliveRto | 1.3.6.1.4.1.18.3.5.18.2.1.10 | INTEGER | read-write | KEEPALIVE retransmit timeout period, in seconds. This is
the interval at which unacknowledged KEEPALIVE messages will
be retransmitted. If the Idle Timer is set to zero, this
timer ignored. If the Idle Timer is non-zero and this timer
IS zero, no KEEPALIVEs are sent and the session is terminated
upon expiration of the Idle Timer. |
| INT wfBotKeepaliveMaxRetry | 1.3.6.1.4.1.18.3.5.18.2.1.11 | INTEGER | read-write | Number of unacknowledged KEEPALIVE messages retransmitted
before the TCP session is terminated. If this count is set
to zero, only one KEEPALIVE message will be sent. |
| wfBotPeerTable | 1.3.6.1.4.1.18.3.5.18.3 | | not-accessible | Peer table lists all TCP connections this router will have
with its peers |
| wfBotPeerEntry | 1.3.6.1.4.1.18.3.5.18.3.1 | | not-accessible | An entry in wfBotPeerTable |
| INT wfBotPeerEntryDelete | 1.3.6.1.4.1.18.3.5.18.3.1.1 | INTEGER | read-write | Create/Delete attribute. Default is Created
Users perform SNMP SET operation on this object in
order to create/delete a peer record |
| INT wfBotPeerEntryDisable | 1.3.6.1.4.1.18.3.5.18.3.1.2 | INTEGER | read-write | Enables/Disables this mapping entry
Setting of this attribute to DISABLED will disconnect
all active sessions pertaining to this interface entry |
| INT wfBotPeerSlotNumber | 1.3.6.1.4.1.18.3.5.18.3.1.3 | INTEGER | read-only | Slot number on which this peer entry is configured |
| INT wfBotPeerCctNumber | 1.3.6.1.4.1.18.3.5.18.3.1.4 | INTEGER | read-only | The circuit from which the connection attempt is
received that initiates a translation session. |
| IP wfBotPeerRemoteIpAddr | 1.3.6.1.4.1.18.3.5.18.3.1.5 | IpAddress | read-only | IP Address of the remote host with which this translation
session is established. |
| INT wfBotConnOriginator | 1.3.6.1.4.1.18.3.5.18.3.1.6 | INTEGER | read-only | Upon start up, based on the configuration either
partner is going to initiate TCP conn. or myself |
| INT wfBotPeerLocalTcpListenPort | 1.3.6.1.4.1.18.3.5.18.3.1.7 | INTEGER | read-only | Based on the field wfBotConnOriginator, SiteManager
will allow user to configure only one of following two fields:
if Originator = SELF then
through SiteManager ask user to enter PeerTcpListenPort#
else
through SiteManager ask user to enter LocalTcpListenPort#
So, in any case one of the two fields will have NULL_VALUE. |
| INT wfBotPeerRemoteTcpListenPort | 1.3.6.1.4.1.18.3.5.18.3.1.8 | INTEGER | read-only | Peer listen port for TCP connection |
| INT wfBotPeerLocalTcpPort | 1.3.6.1.4.1.18.3.5.18.3.1.9 | INTEGER | read-only | When TCP connection is established, we will have other TCP
port number available which is assigned by the system from
the available pool. We will fill in this information here
in this READ_ONLY variable. Again, based on Originator
only one of the following two fields will have valid value.
if Originator = SELF then
fill in LocalTcpPort field inside the BOT module
else
fill in PeerTcpPort field inside the BOT module
In short,
=========
For Originator = SELF
PeerTcpListenPort and LocalTcpPort entries are valid
For Originator = PARTNER
LocalTcpListenPort and PeerTcpPort entries are valid |
| INT wfBotPeerRemoteTcpPort | 1.3.6.1.4.1.18.3.5.18.3.1.10 | INTEGER | read-only | Peer TCP port of the connection |
| wfBotCUTable | 1.3.6.1.4.1.18.3.5.18.4 | | not-accessible | CU table lists all CUs reachable from this router on all
TCP connections listed in PEER_TABLE |
| wfBotCUEntry | 1.3.6.1.4.1.18.3.5.18.4.1 | | not-accessible | An entry in wfBotCUTable |
| INT wfBotCUEntryDelete | 1.3.6.1.4.1.18.3.5.18.4.1.1 | INTEGER | read-write | Create/Delete attribute. Default is Created
Users perform SNMP SET operation on this object in
order to create/delete a peer record |
| INT wfBotCUEntryDisable | 1.3.6.1.4.1.18.3.5.18.4.1.2 | INTEGER | read-write | Enables/Disables this cu entry
Setting of this attribute to DISABLED will disconnect
active TCP conn. pertaining to the peer entry |
| INT wfBotCUSlotNumber | 1.3.6.1.4.1.18.3.5.18.4.1.3 | INTEGER | read-only | slot number used as an index |
| INT wfBotCUCctNumber | 1.3.6.1.4.1.18.3.5.18.4.1.4 | INTEGER | read-only | The circuit from which the connection attempt is
CCT number for easy link between peer table and cu table |
| IP wfBotCURemoteIpAddr | 1.3.6.1.4.1.18.3.5.18.4.1.5 | IpAddress | read-only | IP Address of the remote host with which this translation
session is established. |
| INT wfBotCULocalTcpListenPort | 1.3.6.1.4.1.18.3.5.18.4.1.6 | INTEGER | read-only | As mentioned earlier only one of following two field will
have a valid value, while other will be NULL_VAL, based on
who is the ConnOriginator |
| INT wfBotCURemoteTcpListenPort | 1.3.6.1.4.1.18.3.5.18.4.1.7 | INTEGER | read-only | field from the peer table entry |
| INT wfBotCUAddrReachable | 1.3.6.1.4.1.18.3.5.18.4.1.8 | INTEGER | read-only | In BISYNC controller addresses range from 0-31. In MDL
currently there is no way to represent the integer range.
As lower bound is zero, here we specify only max possible |
