All MIBs › WebGraph-AnalogIO-57661-US-MIB
Category: Power and Environmental Monitoring
Description: Manages WebGraph model 57661 combined analog input and output channels, measured values, and output control.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is WebGraph-AnalogIO-57661-US-MIB?
The WebGraph-AnalogIO-57661-US-MIB is a vendor-specific module for WebGraph's model 57661 analog input/output device, a networked I/O module that measures and controls analog signals (e.g., sensor voltages/currents) over SNMP. It exposes a sensor table describing configured analog channels, a values table holding the current measured/output value for each channel, and a binary values table for digital/threshold-derived states, alongside session-control objects for password protection and configuration-mode locking. In monitoring terms it tracks live analog sensor readings and derived binary status (e.g., an alarm threshold being crossed) rather than classic hardware health counters like CPU or memory, since it is fundamentally an environmental/process I/O monitoring device; its session control password and config-mode objects also confirm the device's management/security state. This is a self-contained vendor MIB with no apparent dependency on other standard MIBs. It is typically deployed in remote monitoring/telemetry applications - environmental monitoring, industrial process sensing, or facility management - where analog transducers are wired into the WebGraph unit and read out over the network. Engineers can download the WebGraph-AnalogIO-57661-US-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in WebGraph-AnalogIO-57661-US-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- WebGraph model 57661 analog I/O module
Monitoring Examples
Polling wtWebGraphAnalog57661ValuesTable/wtWebGraphAnalog57661Values for each entry indexed by wtWebGraphAnalog57661SensorNo returns the live measured value of each analog channel, such as a sensor voltage or current reading. The companion wtWebGraphAnalog57661BinaryValuesTable exposes a derived on/off or threshold-exceeded state per channel, letting an NMS raise an alert when a monitored value crosses a configured limit. wtWebGraphAnalog57661SessCntrlConfigMode and wtWebGraphAnalog57661SessCntrlPassword indicate whether the unit is currently locked for configuration changes, useful for change-control auditing.
What Can Be Monitored
- analog sensor channel values
- binary/threshold-derived channel states
- sensor configuration per channel
- session configuration-mode/lock status
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| IpAddress | |
| NetworkAddress | |
| TimeTicks | |
| enterprises |
From RFC1213-MIB
| DisplayString | |
| PhysAddress |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| wut | 1.3.6.1.4.1.5040 | |||
| wtComServer | 1.3.6.1.4.1.5040.1 | |||
| wtWebio | 1.3.6.1.4.1.5040.1.2 | |||
| wtWebGraphAnalog57661 | 1.3.6.1.4.1.5040.1.2.28 | |||
| NTF wtWebGraphAnalog57661Alert1 | 1.3.6.1.4.1.5040.1.2.28.0.31 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert2 | 1.3.6.1.4.1.5040.1.2.28.0.32 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert3 | 1.3.6.1.4.1.5040.1.2.28.0.33 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert4 | 1.3.6.1.4.1.5040.1.2.28.0.34 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert5 | 1.3.6.1.4.1.5040.1.2.28.0.35 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert6 | 1.3.6.1.4.1.5040.1.2.28.0.36 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert7 | 1.3.6.1.4.1.5040.1.2.28.0.37 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert8 | 1.3.6.1.4.1.5040.1.2.28.0.38 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661AlertReport | 1.3.6.1.4.1.5040.1.2.28.0.39 | This SNMP trap is generated when the report was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert9 | 1.3.6.1.4.1.5040.1.2.28.0.91 | This SNMP trap is generated when Alarm 1 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert10 | 1.3.6.1.4.1.5040.1.2.28.0.92 | This SNMP trap is generated when Alarm 2 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert11 | 1.3.6.1.4.1.5040.1.2.28.0.93 | This SNMP trap is generated when Alarm 3 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert12 | 1.3.6.1.4.1.5040.1.2.28.0.94 | This SNMP trap is generated when Alarm 4 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert13 | 1.3.6.1.4.1.5040.1.2.28.0.95 | This SNMP trap is generated when Alarm 5 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert14 | 1.3.6.1.4.1.5040.1.2.28.0.96 | This SNMP trap is generated when Alarm 6 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert15 | 1.3.6.1.4.1.5040.1.2.28.0.97 | This SNMP trap is generated when Alarm 7 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661Alert16 | 1.3.6.1.4.1.5040.1.2.28.0.98 | This SNMP trap is generated when Alarm 8 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57661AlertDiag | 1.3.6.1.4.1.5040.1.2.28.0.110 | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| wtWebGraphAnalog57661Inventory | 1.3.6.1.4.1.5040.1.2.28.1 | |||
| INT wtWebGraphAnalog57661Sensors | 1.3.6.1.4.1.5040.1.2.28.1.1 | INTEGER | read-only | Number of sensors |
| wtWebGraphAnalog57661SensorTable | 1.3.6.1.4.1.5040.1.2.28.1.2 | not-accessible | List of sensors. | |
| wtWebGraphAnalog57661SensorEntry | 1.3.6.1.4.1.5040.1.2.28.1.2.1 | not-accessible | List of sensor numbers. | |
| INT wtWebGraphAnalog57661SensorNo | 1.3.6.1.4.1.5040.1.2.28.1.2.1.1 | INTEGER | read-only | Sensor number. |
| wtWebGraphAnalog57661ValuesTable | 1.3.6.1.4.1.5040.1.2.28.1.3 | not-accessible | List of measurement values corresponding to the channel numbers. | |
| wtWebGraphAnalog57661ValuesEntry | 1.3.6.1.4.1.5040.1.2.28.1.3.1 | not-accessible | Measurement values of the sensors. | |
| OCT wtWebGraphAnalog57661Values | 1.3.6.1.4.1.5040.1.2.28.1.3.1.1 | OCTET STRING | read-write | Measurement value of the sensor, ASCII. This value will be translated according to the ports settings for the read and write operations. |
| wtWebGraphAnalog57661BinaryValuesTable | 1.3.6.1.4.1.5040.1.2.28.1.4 | not-accessible | List of binary measurement values corresponding to the channel numbers. | |
| wtWebGraphAnalog57661BinaryValuesEntry | 1.3.6.1.4.1.5040.1.2.28.1.4.1 | not-accessible | Binary measurement values of the sensors. | |
| INT wtWebGraphAnalog57661BinaryValues | 1.3.6.1.4.1.5040.1.2.28.1.4.1.1 | INTEGER | read-write | Binary measurement value of the sensor in 1/1000, signed number, 0x7FFFFFFF indicates an invalid value. This value will be translated according to the ports settings for the read and write operations. |
| wtWebGraphAnalog57661SessCntrl | 1.3.6.1.4.1.5040.1.2.28.2 | |||
| OCT wtWebGraphAnalog57661SessCntrlPassword | 1.3.6.1.4.1.5040.1.2.28.2.1 | OCTET STRING | read-write | Entering this password opens a session which is ended by writing a 1 to wtWebGraphAnalog57661SessCntrlLogout. When read this variable provides a string of length zero. |
| INT wtWebGraphAnalog57661SessCntrlConfigMode | 1.3.6.1.4.1.5040.1.2.28.2.2 | INTEGER | read-only | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is already in config mode and the variables can only be read. |
| INT wtWebGraphAnalog57661SessCntrlLogout | 1.3.6.1.4.1.5040.1.2.28.2.3 | INTEGER | read-write | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters are stored. Writing a 2 discards all entries again. When read this variable provides the value 0. |
| OCT wtWebGraphAnalog57661SessCntrlAdminPassword | 1.3.6.1.4.1.5040.1.2.28.2.4 | OCTET STRING | read-write | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid password is public. |
| OCT wtWebGraphAnalog57661SessCntrlConfigPassword | 1.3.6.1.4.1.5040.1.2.28.2.5 | OCTET STRING | read-write | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was assigned, the valid password is public. When read this variable provides a null-pointer. |
| wtWebGraphAnalog57661Config | 1.3.6.1.4.1.5040.1.2.28.3 | |||
| wtWebGraphAnalog57661Device | 1.3.6.1.4.1.5040.1.2.28.3.1 | |||
| wtWebGraphAnalog57661Text | 1.3.6.1.4.1.5040.1.2.28.3.1.1 | |||
| OCT wtWebGraphAnalog57661DeviceName | 1.3.6.1.4.1.5040.1.2.28.3.1.1.1 | OCTET STRING | read-write | Name of the Webio, which is user definable. |
| OCT wtWebGraphAnalog57661DeviceText | 1.3.6.1.4.1.5040.1.2.28.3.1.1.2 | OCTET STRING | read-write | Description of the Webio, which is user definable. |
| OCT wtWebGraphAnalog57661DeviceLocation | 1.3.6.1.4.1.5040.1.2.28.3.1.1.3 | OCTET STRING | read-write | Description of the location of the Webio, which is user definable. |
| OCT wtWebGraphAnalog57661DeviceContact | 1.3.6.1.4.1.5040.1.2.28.3.1.1.4 | OCTET STRING | read-write | Contact address of the system operator of the Webio, which is user definable. |
| wtWebGraphAnalog57661TimeDate | 1.3.6.1.4.1.5040.1.2.28.3.1.2 | |||
| wtWebGraphAnalog57661TimeZone | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1 | |||
| INT wtWebGraphAnalog57661TzOffsetHrs | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.1 | INTEGER | read-write | Offset hours for the time zone (winter time) with respect to UTC. |
| INT wtWebGraphAnalog57661TzOffsetMin | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.2 | INTEGER | read-write | Offset minutes for the time zone (winter time) with respect to UTC. |
| OCT wtWebGraphAnalog57661TzEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.3 | OCTET STRING | read-write | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| INT wtWebGraphAnalog57661StTzOffsetHrs | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.4 | INTEGER | read-write | Offset hours of the time zone (summer time) with respect to UTC. |
| INT wtWebGraphAnalog57661StTzOffsetMin | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.5 | INTEGER | read-write | Offset minutes of the time zone (summer time) with respect to UTC. |
| OCT wtWebGraphAnalog57661StTzEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.6 | OCTET STRING | read-write | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| INT wtWebGraphAnalog57661StTzStartMonth | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.7 | INTEGER | read-write | Month in which the change is made from winter time to summer time. |
| INT wtWebGraphAnalog57661StTzStartMode | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.8 | INTEGER | read-write | Mode of the day of the week for which the change is made from winter time to summer time. |
| INT wtWebGraphAnalog57661StTzStartWday | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.9 | INTEGER | read-write | Day of the week on which the change is made from winter time to summer time |
| INT wtWebGraphAnalog57661StTzStartHrs | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.10 | INTEGER | read-write | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| INT wtWebGraphAnalog57661StTzStartMin | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.11 | INTEGER | read-write | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| INT wtWebGraphAnalog57661StTzStopMonth | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.12 | INTEGER | read-write | Month in which the change is made from summer time to winter time. |
| INT wtWebGraphAnalog57661StTzStopMode | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.13 | INTEGER | read-write | Mode of the week day on which the change is made from summer time to winter time. |
| INT wtWebGraphAnalog57661StTzStopWday | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.14 | INTEGER | read-write | Day of the week on which the change is made from summer time to winter time. |
| INT wtWebGraphAnalog57661StTzStopHrs | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.15 | INTEGER | read-write | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| INT wtWebGraphAnalog57661StTzStopMin | 1.3.6.1.4.1.5040.1.2.28.3.1.2.1.16 | INTEGER | read-write | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| wtWebGraphAnalog57661TimeServer | 1.3.6.1.4.1.5040.1.2.28.3.1.2.2 | |||
| OCT wtWebGraphAnalog57661TimeServer1 | 1.3.6.1.4.1.5040.1.2.28.3.1.2.2.1 | OCTET STRING | read-write | IP address or name of the 1st time server in ASCII |
| OCT wtWebGraphAnalog57661TimeServer2 | 1.3.6.1.4.1.5040.1.2.28.3.1.2.2.2 | OCTET STRING | read-write | IP address or name of the 2nd time server in ASCII |
| OCT wtWebGraphAnalog57661TsEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.2.2.3 | OCTET STRING | read-write | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| INT wtWebGraphAnalog57661TsSyncTime | 1.3.6.1.4.1.5040.1.2.28.3.1.2.2.4 | INTEGER | read-write | Daily synchronisation time with the time server (hour: 0-23). |
| wtWebGraphAnalog57661DeviceClock | 1.3.6.1.4.1.5040.1.2.28.3.1.2.3 | |||
| INT wtWebGraphAnalog57661ClockHrs | 1.3.6.1.4.1.5040.1.2.28.3.1.2.3.1 | INTEGER | read-write | Clock hours taking into account the time zone settings. |
| INT wtWebGraphAnalog57661ClockMin | 1.3.6.1.4.1.5040.1.2.28.3.1.2.3.2 | INTEGER | read-write | Clock minutes taking into account the time zone settings. |
| INT wtWebGraphAnalog57661ClockDay | 1.3.6.1.4.1.5040.1.2.28.3.1.2.3.3 | INTEGER | read-write | Date: Day of the month, taking into account the time zone settings. |
| INT wtWebGraphAnalog57661ClockMonth | 1.3.6.1.4.1.5040.1.2.28.3.1.2.3.4 | INTEGER | read-write | Date: Month, taking into account the time zone settings. |
| INT wtWebGraphAnalog57661ClockYear | 1.3.6.1.4.1.5040.1.2.28.3.1.2.3.5 | INTEGER | read-write | Date: Year, taking into account the time zone settings. |
| wtWebGraphAnalog57661Basic | 1.3.6.1.4.1.5040.1.2.28.3.1.3 | |||
| wtWebGraphAnalog57661Network | 1.3.6.1.4.1.5040.1.2.28.3.1.3.1 | |||
| IP wtWebGraphAnalog57661IpAddress | 1.3.6.1.4.1.5040.1.2.28.3.1.3.1.1 | IpAddress | read-write | IP address of the Webio |
| IP wtWebGraphAnalog57661SubnetMask | 1.3.6.1.4.1.5040.1.2.28.3.1.3.1.2 | IpAddress | read-write | Subnet mask of the Webio |
| IP wtWebGraphAnalog57661Gateway | 1.3.6.1.4.1.5040.1.2.28.3.1.3.1.3 | IpAddress | read-write | Gateway of the Webio |
| OCT wtWebGraphAnalog57661DnsServer1 | 1.3.6.1.4.1.5040.1.2.28.3.1.3.1.4 | OCTET STRING | read-write | IP address of the 1st DNS server in ASCII |
| OCT wtWebGraphAnalog57661DnsServer2 | 1.3.6.1.4.1.5040.1.2.28.3.1.3.1.5 | OCTET STRING | read-write | IP address of the 2nd DNS server in ASCII |
| OCT wtWebGraphAnalog57661AddConfig | 1.3.6.1.4.1.5040.1.2.28.3.1.3.1.6 | OCTET STRING | read-write | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP disable Bit 0: BOOTP disable |
| wtWebGraphAnalog57661HTTP | 1.3.6.1.4.1.5040.1.2.28.3.1.3.2 | |||
| OCT wtWebGraphAnalog57661Startup | 1.3.6.1.4.1.5040.1.2.28.3.1.3.2.1 | OCTET STRING | read-write | Binary coded start page: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: Index.htm Bit 2: Home.htm Bit 3: User.htm Only one page may be selected at a time. |
| OCT wtWebGraphAnalog57661GetHeaderEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.3.2.2 | OCTET STRING | read-write | If these bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device and/or a HTTP header: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-6: unused Bit 1 : GET HTTP enable Bit 0 : GET Header enable |
| INT wtWebGraphAnalog57661HttpPort | 1.3.6.1.4.1.5040.1.2.28.3.1.3.2.3 | INTEGER | read-write | Definition of the standard HTML port (Default: 80). |
| wtWebGraphAnalog57661Mail | 1.3.6.1.4.1.5040.1.2.28.3.1.3.3 | |||
| OCT wtWebGraphAnalog57661MailAdName | 1.3.6.1.4.1.5040.1.2.28.3.1.3.3.1 | OCTET STRING | read-write | Device name for mail administration. |
| OCT wtWebGraphAnalog57661MailReply | 1.3.6.1.4.1.5040.1.2.28.3.1.3.3.2 | OCTET STRING | read-write | Reply address for the mail server. |
| OCT wtWebGraphAnalog57661MailServer | 1.3.6.1.4.1.5040.1.2.28.3.1.3.3.3 | OCTET STRING | read-write | Name or IP address of the mail server. |
| OCT wtWebioAn1MailEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.3.3.4 | OCTET STRING | read-write | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| OCT wtWebGraphAnalog57661MailAuthentication | 1.3.6.1.4.1.5040.1.2.28.3.1.3.3.5 | OCTET STRING | read-write | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 3-7: unused Bit 2 : POP3 before SMTP Bit 1 : ESMTP, authentication Bit 0 : SMTP, no authentication |
| OCT wtWebGraphAnalog57661MailAuthUser | 1.3.6.1.4.1.5040.1.2.28.3.1.3.3.6 | OCTET STRING | read-write | Name of the user to be authenticated. |
| OCT wtWebGraphAnalog57661MailAuthPassword | 1.3.6.1.4.1.5040.1.2.28.3.1.3.3.7 | OCTET STRING | read-write | Authentication password. |
| OCT wtWebGraphAnalog57661MailPop3Server | 1.3.6.1.4.1.5040.1.2.28.3.1.3.3.8 | OCTET STRING | read-write | Name or Ip-address of the POP3 Servers. |
| wtWebGraphAnalog57661SNMP | 1.3.6.1.4.1.5040.1.2.28.3.1.3.4 | |||
| OCT wtWebGraphAnalog57661SnmpCommunityStringRead | 1.3.6.1.4.1.5040.1.2.28.3.1.3.4.1 | OCTET STRING | read-write | Community string read only |
| OCT wtWebGraphAnalog57661SnmpCommunityStringReadWrite | 1.3.6.1.4.1.5040.1.2.28.3.1.3.4.2 | OCTET STRING | read-write | Community string read / write |
| OCT wtWebGraphAnalog57661SystemTrapManagerIP | 1.3.6.1.4.1.5040.1.2.28.3.1.3.4.3 | OCTET STRING | read-write | Name or IP address of the TCP server which accepts the system trap. |
| OCT wtWebGraphAnalog57661SystemTrapEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.3.4.4 | OCTET STRING | read-write | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2-7: unused |
| OCT wtWebGraphAnalog57661SnmpEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.3.4.5 | OCTET STRING | read-write | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compared with the system password or not: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : SNMP enable |
| OCT wtWebGraphAnalog57661SnmpCommunityStringTrap | 1.3.6.1.4.1.5040.1.2.28.3.1.3.4.6 | OCTET STRING | read-write | Community string send within traps. |
| wtWebGraphAnalog57661UDP | 1.3.6.1.4.1.5040.1.2.28.3.1.3.5 | |||
| INT wtWebGraphAnalog57661UdpPort | 1.3.6.1.4.1.5040.1.2.28.3.1.3.5.1 | INTEGER | read-write | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| OCT wtWebGraphAnalog57661UdpEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.3.5.2 | OCTET STRING | read-write | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| wtWebGraphAnalog57661Syslog | 1.3.6.1.4.1.5040.1.2.28.3.1.3.6 | |||
| OCT wtWebGraphAnalog57661SyslogServerIP | 1.3.6.1.4.1.5040.1.2.28.3.1.3.6.1 | OCTET STRING | read-write | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| INT wtWebGraphAnalog57661SyslogServerPort | 1.3.6.1.4.1.5040.1.2.28.3.1.3.6.2 | INTEGER | read-write | Portnumber of the Syslog servers, default 514. |
| OCT wtWebGraphAnalog57661SyslogSystemMessagesEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.3.6.3 | OCTET STRING | read-write | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| OCT wtWebGraphAnalog57661SyslogEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.3.6.4 | OCTET STRING | read-write | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| wtWebGraphAnalog57661FTP | 1.3.6.1.4.1.5040.1.2.28.3.1.3.7 | |||
| OCT wtWebGraphAnalog57661FTPServerIP | 1.3.6.1.4.1.5040.1.2.28.3.1.3.7.1 | OCTET STRING | read-write | Name or IP address of the FTP server, which accepts the FTP messages. |
| INT wtWebGraphAnalog57661FTPServerControlPort | 1.3.6.1.4.1.5040.1.2.28.3.1.3.7.2 | INTEGER | read-write | Portnumber of the control port of the FTP server, default 21. |
| OCT wtWebGraphAnalog57661FTPUserName | 1.3.6.1.4.1.5040.1.2.28.3.1.3.7.3 | OCTET STRING | read-write | FTP Loggin: user name. |
| OCT wtWebGraphAnalog57661FTPPassword | 1.3.6.1.4.1.5040.1.2.28.3.1.3.7.4 | OCTET STRING | read-write | FTP Loggin: user password. |
| OCT wtWebGraphAnalog57661FTPAccount | 1.3.6.1.4.1.5040.1.2.28.3.1.3.7.5 | OCTET STRING | read-write | FTP Loggin: name of account. |
| OCT wtWebGraphAnalog57661FTPOption | 1.3.6.1.4.1.5040.1.2.28.3.1.3.7.6 | OCTET STRING | read-write | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : PASV enable |
| OCT wtWebGraphAnalog57661FTPEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.3.7.7 | OCTET STRING | read-write | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| wtWebGraphAnalog57661Language | 1.3.6.1.4.1.5040.1.2.28.3.1.3.8 | |||
| OCT wtWebGraphAnalog57661LanguageSelect | 1.3.6.1.4.1.5040.1.2.28.3.1.3.8.1 | OCTET STRING | read-write | Language selection: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2-7: unused Bit 1 : English Bit 0 : German |
| wtWebGraphAnalog57661Binary | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9 | |||
| INT wtWebGraphAnalog57661BinaryModeCount | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.1 | INTEGER | read-only | Number of independent binary channels. |
| wtWebGraphAnalog57661BinaryIfTable | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.2 | not-accessible | Table of indices. | |
| wtWebGraphAnalog57661BinaryIfEntry | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.2.1 | not-accessible | Indices of the binary channels. | |
| INT wtWebGraphAnalog57661BinaryModeNo | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.2.1.1 | INTEGER | read-only | Number of the binary channel. |
| wtWebGraphAnalog57661BinaryTable | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3 | not-accessible | Table of properties of the binary mode. | |
| wtWebGraphAnalog57661BinaryEntry | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1 | not-accessible | Binary properties. | |
| OCT wtWebGraphAnalog57661BinaryOperationMode | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.1 | OCTET STRING | read-write | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 3-7: unused Bit 2 : UDP Peer Bit 1 : TCP Client Bit 0 : TCP Server |
| INT wtWebGraphAnalog57661BinaryTcpServerLocalPort | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.2 | INTEGER | read-write | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the manual). |
| OCT wtWebGraphAnalog57661BinaryTcpServerInputTrigger | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.3 | OCTET STRING | read-write | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rule. Nevertheless every transmission will contain all input states. If a bit is set (1), a change of state on the corresponding input triggers a transmission. If the bit is not set (0), no transmission takes place. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 0-1: Analog inputs 0-1 |
| OCT wtWebGraphAnalog57661BinaryTcpServerApplicationMode | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.4 | OCTET STRING | read-write | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 4-7: unused Bit 3 : OPC Device Bit 2 : Box2Box Slave Bit 1 : Compatible 50xxx Bit 0 : Default |
| INT wtWebGraphAnalog57661BinaryTcpClientLocalPort | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.5 | INTEGER | read-write | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the manual). |
| INT wtWebGraphAnalog57661BinaryTcpClientServerPort | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.6 | INTEGER | read-write | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting the server port to zero. |
| OCT wtWebGraphAnalog57661BinaryTcpClientServerIpAddr | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.7 | OCTET STRING | read-write | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting the server IP address to 0.0.0.0. |
| OCT wtWebGraphAnalog57661BinaryTcpClientServerPassword | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.8 | OCTET STRING | read-write | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administrator password exists. |
| INT wtWebGraphAnalog57661BinaryTcpClientInactivity | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.9 | INTEGER | read-write | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the timer. Using the Box2Box mode this function is disabled. |
| OCT wtWebGraphAnalog57661BinaryTcpClientInputTrigger | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.10 | OCTET STRING | read-write | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rule. Nevertheless every transmission will contain all input states. If a bit is set (1), a change of state on the corresponding input triggers a transmission. If the bit is not set (0), no transmission takes place. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 0-1: Analog inputs 0-1 |
| INT wtWebGraphAnalog57661BinaryTcpClientInterval | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.11 | INTEGER | read-write | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| OCT wtWebGraphAnalog57661BinaryTcpClientApplicationMode | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.12 | OCTET STRING | read-write | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 3-7: unused Bit 2 : Box2Box Slave Bit 1 : Compatible 50xxx Bit 0 : Default |
| INT wtWebGraphAnalog57661BinaryUdpPeerLocalPort | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.13 | INTEGER | read-write | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to the manual). |
| INT wtWebGraphAnalog57661BinaryUdpPeerRemotePort | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.14 | INTEGER | read-write | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting the remote port to zero. |
| OCT wtWebGraphAnalog57661BinaryUdpPeerRemoteIpAddr | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.15 | OCTET STRING | read-write | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting the remote device IP address to 0.0.0.0. |
| OCT wtWebGraphAnalog57661BinaryUdpPeerInputTrigger | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.16 | OCTET STRING | read-write | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rule. Nevertheless every transmission will contain all input states. If a bit is set (1), a change of state on the corresponding input triggers a transmission. If the bit is not set (0), no transmission takes place. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 0-1: Analog inputs 0-1 |
| INT wtWebGraphAnalog57661BinaryUdpPeerInterval | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.17 | INTEGER | read-write | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| OCT wtWebGraphAnalog57661BinaryUdpPeerApplicationMode | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.18 | OCTET STRING | read-write | Selection of the application mode: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 3-7: unused Bit 2 : Box2Box Slave Bit 1 : Compatible 50xxx Bit 0 : Default |
| INT wtWebGraphAnalog57661BinaryConnectedPort | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.19 | INTEGER | read-only | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| IP wtWebGraphAnalog57661BinaryConnectedIpAddr | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.20 | IpAddress | read-only | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| INT wtWebGraphAnalog57661BinaryTcpServerClientHttpPort | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.21 | INTEGER | read-write | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible 50xxx. |
| INT wtWebGraphAnalog57661BinaryTcpClientServerHttpPort | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.22 | INTEGER | read-write | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| OCT wtWebGraphAnalog57661BinaryTcpServerHysteresis1 | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.23 | OCTET STRING | read-write | A change greater than this value initiate a transmission of the corresponding input value. The input 1 must be selected at wtWebGraphAnalog57661BinaryTcpServerInputTrigger. With a hysteresis of zero any change will be transmitted. |
| OCT wtWebGraphAnalog57661BinaryTcpServerHysteresis2 | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.24 | OCTET STRING | read-write | A change greater than this value initiate a transmission of the corresponding input value. The input 2 must be selected at wtWebGraphAnalog57661BinaryTcpServerInputTrigger. With a hysteresis of zero any change will be transmitted. |
| OCT wtWebGraphAnalog57661BinaryTcpClientHysteresis1 | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.25 | OCTET STRING | read-write | A change greater than this value initiate a transmission of the corresponding input value. The input 1 must be selected at wtWebGraphAnalog57661BinaryTcpClientInputTrigger. With a hysteresis of zero any change will be transmitted. |
| OCT wtWebGraphAnalog57661BinaryTcpClientHysteresis2 | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.26 | OCTET STRING | read-write | A change greater than this value initiate a transmission of the corresponding input value. The input 2 must be selected at wtWebGraphAnalog57661BinaryTcpClientInputTrigger. With a hysteresis of zero any change will be transmitted. |
| OCT wtWebGraphAnalog57661BinaryUdpPeerHysteresis1 | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.27 | OCTET STRING | read-write | A change greater than this value initiate a transmission of the corresponding input value. The input 1 must be selected at wtWebGraphAnalog57661BinaryUdpPeerInputTrigger. With a hysteresis of zero any change will be transmitted. |
| OCT wtWebGraphAnalog57661BinaryUdpPeerHysteresis2 | 1.3.6.1.4.1.5040.1.2.28.3.1.3.9.3.1.28 | OCTET STRING | read-write | A change greater than this value initiate a transmission of the corresponding input value. The input 2 must be selected at wtWebGraphAnalog57661BinaryUdpPeerInputTrigger. With a hysteresis of zero any change will be transmitted. |
| wtWebGraphAnalog57661Datalogger | 1.3.6.1.4.1.5040.1.2.28.3.1.4 | |||
| INT wtWebGraphAnalog57661LoggerTimebase | 1.3.6.1.4.1.5040.1.2.28.3.1.4.1 | INTEGER | read-write | Time base of the data logger |
| OCT wtWebGraphAnalog57661LoggerSensorSel | 1.3.6.1.4.1.5040.1.2.28.3.1.4.2 | OCTET STRING | read-write | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 Bit 2-7: unused |
| OCT wtWebGraphAnalog57661DisplaySensorSel | 1.3.6.1.4.1.5040.1.2.28.3.1.4.3 | OCTET STRING | read-write | Binary coded sensor selection: only selected sensors will be shown in the graphical presentation: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 Bit 2-7: unused |
| wtWebGraphAnalog57661SensorColorTable | 1.3.6.1.4.1.5040.1.2.28.3.1.4.4 | not-accessible | List of sensor colors for the praphical presentation. | |
| wtWebGraphAnalog57661SensorColorEntry | 1.3.6.1.4.1.5040.1.2.28.3.1.4.4.1 | not-accessible | Index numbers of the sensors. | |
| OCT wtWebGraphAnalog57661SensorColor | 1.3.6.1.4.1.5040.1.2.28.3.1.4.4.1.1 | OCTET STRING | read-write | Color of the sensors at the praphical presention. |
| OCT wtWebGraphAnalog57661AutoScaleEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.4.5 | OCTET STRING | read-write | If bit 0 is set, vertical auto scale is enabled: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Auto Scale enable |
| OCT wtWebGraphAnalog57661VerticalUpperLimit | 1.3.6.1.4.1.5040.1.2.28.3.1.4.6 | OCTET STRING | read-write | This value defines the maximum temperature shown in the graphical presentation, if no auto scaling is selected. Temperature in degrees with maximum 2 decimal places. |
| OCT wtWebGraphAnalog57661VerticalLowerLimit | 1.3.6.1.4.1.5040.1.2.28.3.1.4.7 | OCTET STRING | read-write | This value defines the minimum temperature shown in the graphical presentation, if no auto scaling is selected. Temperature in degrees with maximum 2 decimal places. |
| INT wtWebGraphAnalog57661HorizontalZoom | 1.3.6.1.4.1.5040.1.2.28.3.1.4.8 | INTEGER | read-write | Defines the default zoom stage, if no auto scaling is selected. |
| wtWebGraphAnalog57661Alarm | 1.3.6.1.4.1.5040.1.2.28.3.1.5 | |||
| INT wtWebGraphAnalog57661AlarmCount | 1.3.6.1.4.1.5040.1.2.28.3.1.5.1 | INTEGER | read-only | Number of independent alarms. |
| wtWebGraphAnalog57661AlarmIfTable | 1.3.6.1.4.1.5040.1.2.28.3.1.5.2 | not-accessible | List of alarm indices. | |
| wtWebGraphAnalog57661AlarmIfEntry | 1.3.6.1.4.1.5040.1.2.28.3.1.5.2.1 | not-accessible | Numbers of the alarms. | |
| INT wtWebGraphAnalog57661AlarmNo | 1.3.6.1.4.1.5040.1.2.28.3.1.5.2.1.1 | INTEGER | read-only | Alarm number. |
| wtWebGraphAnalog57661AlarmTable | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3 | not-accessible | List of settings depending on the alarm number. | |
| wtWebGraphAnalog57661AlarmEntry | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1 | not-accessible | Alarm parameters of the individual alarms. | |
| OCT wtWebGraphAnalog57661AlarmTrigger | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.1 | OCTET STRING | read-write | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: Bit 0: Timer Bit 1: ColdStart Bit 2: WarmStart Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 Bit 2-7: unused |
| OCT wtWebGraphAnalog57661AlarmMin1 | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.2 | OCTET STRING | read-write | Minimum sensor 1 with maximum 3 decimal places. |
| OCT wtWebGraphAnalog57661AlarmMax1 | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.3 | OCTET STRING | read-write | Maximum sensor 1 with maximum 3 decimal places. |
| OCT wtWebGraphAnalog57661AlarmHysteresis1 | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.4 | OCTET STRING | read-write | Reading changes of this size clears the alarm state (MAX-hyst, MIN+hyst.) with maximum 3 decimal places. |
| OCT wtWebGraphAnalog57661AlarmDelay | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.5 | OCTET STRING | read-write | Alarm will be delayed by setting this time while stable alarm condition occur (time in minutes). |
| OCT wtWebGraphAnalog57661AlarmInterval | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.6 | OCTET STRING | read-write | Send interval for alarm messages. |
| OCT wtWebGraphAnalog57661AlarmEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.7 | OCTET STRING | read-write | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: TCP Client enable Bit 3: Syslog enable Bit 4: FTP Client enable |
| OCT wtWebGraphAnalog57661AlarmEMailAddr | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.8 | OCTET STRING | read-write | E-Mail address for sending the alarm mail to. |
| OCT wtWebGraphAnalog57661AlarmMailSubject | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.9 | OCTET STRING | read-write | Subject line for alarm mail. |
| OCT wtWebGraphAnalog57661AlarmMailText | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.10 | OCTET STRING | read-write | Alarm mail text: provides the current temperature; n = 1..2. provides the current time. |
| OCT wtWebGraphAnalog57661AlarmManagerIP | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.11 | OCTET STRING | read-write | Name or IP address of the SNMP Manager which accepts the trap. |
| OCT wtWebGraphAnalog57661AlarmTrapText | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.12 | OCTET STRING | read-write | This text is sent in the trap body. |
| OCT wtWebGraphAnalog57661AlarmMailOptions | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.13 | OCTET STRING | read-write | Binary coded options: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Attach Logger.csv Enable Bit 1 : CSV-Data_since_last_report Bit 2-7: unused |
| OCT wtWebGraphAnalog57661AlarmTcpIpAddr | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.14 | OCTET STRING | read-write | Name or IP address of the TCP server which accepts the trap. |
| INT wtWebGraphAnalog57661AlarmTcpPort | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.15 | INTEGER | read-write | Port number of the TCP server which accepts the trap. |
| OCT wtWebGraphAnalog57661AlarmTcpText | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.16 | OCTET STRING | read-write | This text is sent in the TCP trap body. |
| OCT wtWebGraphAnalog57661AlarmClearMailSubject | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.17 | OCTET STRING | read-write | Subject line for alarm clear mail. |
| OCT wtWebGraphAnalog57661AlarmClearMailText | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.18 | OCTET STRING | read-write | Alarm clear mail text: provides the current temperature; n = 1..2. provides the current time. |
| OCT wtWebGraphAnalog57661AlarmClearTrapText | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.19 | OCTET STRING | read-write | This text is sent in the trap body. |
| OCT wtWebGraphAnalog57661AlarmClearTcpText | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.20 | OCTET STRING | read-write | This text is sent in the TCP trap body. |
| OCT wtWebGraphAnalog57661AlarmMin2 | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.21 | OCTET STRING | read-write | Minimum sensor 2 with maximum 3 decimal places. |
| OCT wtWebGraphAnalog57661AlarmMax2 | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.22 | OCTET STRING | read-write | Maximum sensor 2 with maximum 2 decimal places. |
| OCT wtWebGraphAnalog57661AlarmHysteresis2 | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.23 | OCTET STRING | read-write | Hysterese rel. sensor 2 with maximum 3 decimal places. |
| OCT wtWebGraphAnalog57661AlarmSyslogIpAddr | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.24 | OCTET STRING | read-write | IP address of the syslog server to which the Webio device should send syslog messages. |
| INT wtWebGraphAnalog57661AlarmSyslogPort | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.25 | INTEGER | read-write | Port number of the syslog server to which the Webio device should send syslog messages. |
| OCT wtWebGraphAnalog57661AlarmSyslogText | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.26 | OCTET STRING | read-write | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| OCT wtWebGraphAnalog57661AlarmSyslogClearText | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.27 | OCTET STRING | read-write | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body of a alarm clear message. |
| OCT wtWebGraphAnalog57661AlarmFtpDataPort | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.28 | OCTET STRING | read-write | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| OCT wtWebGraphAnalog57661AlarmFtpFileName | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.29 | OCTET STRING | read-write | Name of the file including path informations. |
| OCT wtWebGraphAnalog57661AlarmFtpText | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.30 | OCTET STRING | read-write | Message text to store on the FTP server. |
| OCT wtWebGraphAnalog57661AlarmFtpClearText | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.31 | OCTET STRING | read-write | Alarm clear message to store on the FTP server. |
| OCT wtWebGraphAnalog57661AlarmFtpOption | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.32 | OCTET STRING | read-write | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : STORE Bit 1 : APPEND Bit 2-7: unused |
| OCT wtWebGraphAnalog57661AlarmTimerCron | 1.3.6.1.4.1.5040.1.2.28.3.1.5.3.1.33 | OCTET STRING | read-write | This entry defines a time window for alarm 1-8 and a activation time for the report. A time window is definied by start and stop time stamp, seperated by a space or tab. The activation time of the report is defined by a single start time stamp. Each time stamp contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger an action, weekday and day of month are interpreted separatley. 1: Minutes Range 0-59 2. Hours Range 0-23, 0 is midnight 3: Day of month Range 1-31 4: Month Range 1-12 5: Weekday Range 0-6, 0 is sunday Syntax for every field: - an asterix (*) enables every possible setting of a field - single numbers seperated by commas (i.e.: 2,14,22) - a partition within the allowed range (i.e.: 1-5) - step size within a partition of the allowed range (i.e.: 0-59/2 every second minute). |
| wtWebGraphAnalog57661Graphics | 1.3.6.1.4.1.5040.1.2.28.3.1.6 | |||
| wtWebGraphAnalog57661GraphicsBase | 1.3.6.1.4.1.5040.1.2.28.3.1.6.1 | |||
| OCT wtWebGraphAnalog57661GraphicsBaseEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.6.1.1 | OCTET STRING | read-write | Defines the viewing options of the graphic: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Auto scroll enable Bit 1 : Show table Bit 2 : Show graph Bit 3 : Show control buttons Bit 4 : Show config menu Bit 5-7: unused |
| INT wtWebGraphAnalog57661GraphicsBaseWidth | 1.3.6.1.4.1.5040.1.2.28.3.1.6.1.2 | INTEGER | read-write | Defines the width of the graphic in pixels. |
| INT wtWebGraphAnalog57661GraphicsBaseHeight | 1.3.6.1.4.1.5040.1.2.28.3.1.6.1.3 | INTEGER | read-write | Defines the height of the graphic in pixels. |
| OCT wtWebGraphAnalog57661GraphicsBaseFrameColor | 1.3.6.1.4.1.5040.1.2.28.3.1.6.1.4 | OCTET STRING | read-write | Frame color definition in RGB. |
| OCT wtWebGraphAnalog57661GraphicsBaseBackgroundColor | 1.3.6.1.4.1.5040.1.2.28.3.1.6.1.5 | OCTET STRING | read-write | Background color definition in RGB. |
| INT wtWebGraphAnalog57661GraphicsBasePollingrate | 1.3.6.1.4.1.5040.1.2.28.3.1.6.1.6 | INTEGER | read-write | Defines the pollingrate in seconds, which defines the refreshing intervall of the graphic. |
| wtWebGraphAnalog57661GraphicsSelect | 1.3.6.1.4.1.5040.1.2.28.3.1.6.2 | |||
| OCT wtWebGraphAnalog57661GraphicsSelectDisplaySensorSel | 1.3.6.1.4.1.5040.1.2.28.3.1.6.2.1 | OCTET STRING | read-write | Binary coded sensor selection: only selected sensors will be shown in the graphical presentation: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 Bit 2-7: unused |
| OCT wtWebGraphAnalog57661GraphicsSelectDisplayShowExtrem | 1.3.6.1.4.1.5040.1.2.28.3.1.6.2.2 | OCTET STRING | read-write | Binary coded sensor selection: only selected sensors will be shown with minima and maxima: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 Bit 2-7: unused |
| wtWebGraphAnalog57661SensorColor2Table | 1.3.6.1.4.1.5040.1.2.28.3.1.6.2.3 | not-accessible | List of sensor colors for the praphical presentation. | |
| wtWebGraphAnalog57661SensorColor2Entry | 1.3.6.1.4.1.5040.1.2.28.3.1.6.2.3.1 | not-accessible | Numbers of the sensors. | |
| OCT wtWebGraphAnalog57661GraphicsSensorColor | 1.3.6.1.4.1.5040.1.2.28.3.1.6.2.3.1.1 | OCTET STRING | read-write | Color of the sensors at the praphical presention. |
| OCT wtWebGraphAnalog57661GraphicsSelectScale | 1.3.6.1.4.1.5040.1.2.28.3.1.6.2.3.1.2 | OCTET STRING | read-write | Assignes one of 4 scales to a sensor: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Use Scale 1 Bit 1 : Use Scale 2 Bit 2-7: unused |
| wtWebGraphAnalog57661GraphicsScale | 1.3.6.1.4.1.5040.1.2.28.3.1.6.3 | |||
| OCT wtWebGraphAnalog57661GraphicsScaleAutoScaleEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.6.3.1 | OCTET STRING | read-write | Select the Auto Scale Mode: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Scale 1 Auto scale enable Bit 1 : Scale 2 Auto scale enable Bit 2-7: unused |
| OCT wtWebGraphAnalog57661GraphicsScaleAutoFitEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.6.3.2 | OCTET STRING | read-write | Select the Auto Fit Mode:: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Scale 1 Auto fit enable Bit 1 : Scale 2 Auto fit enable Bit 2-7: unused |
| INT wtWebGraphAnalog57661GraphicsScale1Min | 1.3.6.1.4.1.5040.1.2.28.3.1.6.3.3 | INTEGER | read-only | Scale 1: Minimum. |
| INT wtWebGraphAnalog57661GraphicsScale2Min | 1.3.6.1.4.1.5040.1.2.28.3.1.6.3.4 | INTEGER | read-only | Scale 2: Minimum. |
| INT wtWebGraphAnalog57661GraphicsScale1Max | 1.3.6.1.4.1.5040.1.2.28.3.1.6.3.7 | INTEGER | read-only | Scale 1: Maximum. |
| INT wtWebGraphAnalog57661GraphicsScale2Max | 1.3.6.1.4.1.5040.1.2.28.3.1.6.3.8 | INTEGER | read-only | Scale 2: Maximum. |
| OCT wtWebGraphAnalog57661GraphicsScale1Unit | 1.3.6.1.4.1.5040.1.2.28.3.1.6.3.11 | OCTET STRING | read-only | Scale 1: Unit. |
| OCT wtWebGraphAnalog57661GraphicsScale2Unit | 1.3.6.1.4.1.5040.1.2.28.3.1.6.3.12 | OCTET STRING | read-only | Scale 2: Unit. |
| wtWebGraphAnalog57661Report | 1.3.6.1.4.1.5040.1.2.28.3.1.7 | |||
| INT wtWebGraphAnalog57661ReportCount | 1.3.6.1.4.1.5040.1.2.28.3.1.7.1 | INTEGER | read-only | Number of independent Reports. |
| wtWebGraphAnalog57661ReportIfTable | 1.3.6.1.4.1.5040.1.2.28.3.1.7.2 | not-accessible | List of Report indices. | |
| wtWebGraphAnalog57661ReportIfEntry | 1.3.6.1.4.1.5040.1.2.28.3.1.7.2.1 | not-accessible | Numbers of the Reports. | |
| INT wtWebGraphAnalog57661ReportNo | 1.3.6.1.4.1.5040.1.2.28.3.1.7.2.1.1 | INTEGER | read-only | Report number. |
| wtWebGraphAnalog57661ReportTable | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3 | not-accessible | List of settings depending on the Report number. | |
| wtWebGraphAnalog57661ReportEntry | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1 | not-accessible | Report parameters of the individual Reports. | |
| OCT wtWebGraphAnalog57661ReportEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.1 | OCTET STRING | read-write | Bin�r kodierte Triggerbedingungen: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Report enable Bit 1-7: unused |
| OCT wtWebGraphAnalog57661ReportTimerCron | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.2 | OCTET STRING | read-write | This entry defines a time window for alarm 1-8 and a activation time for the report. A time window is definied by start and stop time stamp, seperated by a space or tab. The activation time of the report is defined by a single start time stamp. Each time stamp contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger an action, weekday and day of month are interpreted separatley. 1: Minutes Range 0-59 2. Hours Range 0-23, 0 is midnight 3: Day of month Range 1-31 4: Month Range 1-12 5: Weekday Range 0-6, 0 is sunday Syntax for every field: - an asterix (*) enables every possible setting of a field - single numbers seperated by commas (i.e.: 2,14,22) - a partition within the allowed range (i.e.: 1-5) - step size within a partition of the allowed range (i.e.: 0-59/2 every second minute). |
| OCT wtWebGraphAnalog57661ReportMethodeEnable | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.3 | OCTET STRING | read-write | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: TCP Client enable Bit 3: Syslog enable Bit 4: FTP Client enable |
| OCT wtWebGraphAnalog57661ReportEMailAddr | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.8 | OCTET STRING | read-write | E-Mail address for sending the alarm mail to. |
| OCT wtWebGraphAnalog57661ReportMailSubject | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.9 | OCTET STRING | read-write | Subject line for alarm mail. |
| OCT wtWebGraphAnalog57661ReportMailText | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.10 | OCTET STRING | read-write | Report mail text: provides the current temperature; n = 1..2. provides the current time. |
| OCT wtWebGraphAnalog57661ReportManagerIP | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.11 | OCTET STRING | read-write | Name or IP address of the SNMP Manager which accepts the trap. |
| OCT wtWebGraphAnalog57661ReportTrapText | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.12 | OCTET STRING | read-write | This text is sent in the trap body. |
| OCT wtWebGraphAnalog57661ReportMailOptions | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.13 | OCTET STRING | read-write | Binary coded options: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Attach Logger.csv Enable Bit 1 : CSV-Data_since_last_report Bit 2-7: unused |
| OCT wtWebGraphAnalog57661ReportTcpIpAddr | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.14 | OCTET STRING | read-write | Name or IP address of the TCP server which accepts the trap. |
| INT wtWebGraphAnalog57661ReportTcpPort | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.15 | INTEGER | read-write | Port number of the TCP server which accepts the trap. |
| OCT wtWebGraphAnalog57661ReportTcpText | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.16 | OCTET STRING | read-write | This text is sent in the TCP trap body. |
| OCT wtWebGraphAnalog57661ReportClearMailSubject | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.17 | OCTET STRING | read-write | Subject line for alarm clear mail. |
| OCT wtWebGraphAnalog57661ReportClearMailText | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.18 | OCTET STRING | read-write | Report clear mail text: provides the current temperature; n = 1..2. provides the current time. |
| OCT wtWebGraphAnalog57661ReportClearTrapText | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.19 | OCTET STRING | read-write | This text is sent in the trap body. |
| OCT wtWebGraphAnalog57661ReportClearTcpText | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.20 | OCTET STRING | read-write | This text is sent in the TCP trap body. |
| OCT wtWebGraphAnalog57661ReportSyslogIpAddr | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.24 | OCTET STRING | read-write | IP address of the syslog server to which the Webio device should send syslog messages. |
| INT wtWebGraphAnalog57661ReportSyslogPort | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.25 | INTEGER | read-write | Port number of the syslog server to which the Webio device should send syslog messages. |
| OCT wtWebGraphAnalog57661ReportSyslogText | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.26 | OCTET STRING | read-write | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| OCT wtWebGraphAnalog57661ReportSyslogClearText | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.27 | OCTET STRING | read-write | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body of a alarm clear message. |
| OCT wtWebGraphAnalog57661ReportFtpDataPort | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.28 | OCTET STRING | read-write | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| OCT wtWebGraphAnalog57661ReportFtpFileName | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.29 | OCTET STRING | read-write | Name of the file including path informations. |
| OCT wtWebGraphAnalog57661ReportFtpText | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.30 | OCTET STRING | read-write | Message text to store on the FTP server. |
| OCT wtWebGraphAnalog57661ReportFtpClearText | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.31 | OCTET STRING | read-write | Report clear message to store on the FTP server. |
| OCT wtWebGraphAnalog57661ReportFtpOption | 1.3.6.1.4.1.5040.1.2.28.3.1.7.3.1.32 | OCTET STRING | read-write | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : STORE Bit 1 : APPEND Bit 2-7: unused |
| wtWebGraphAnalog57661Ports | 1.3.6.1.4.1.5040.1.2.28.3.2 | |||
| wtWebGraphAnalog57661PortTable | 1.3.6.1.4.1.5040.1.2.28.3.2.1 | not-accessible | List of settings depending on the sensor number. | |
| wtWebGraphAnalog57661PortEntry | 1.3.6.1.4.1.5040.1.2.28.3.2.1.1 | not-accessible | Sensor parameters for the individual sensors. | |
| OCT wtWebGraphAnalog57661PortName | 1.3.6.1.4.1.5040.1.2.28.3.2.1.1.1 | OCTET STRING | read-write | Name of the sensor. |
| OCT wtWebGraphAnalog57661PortText | 1.3.6.1.4.1.5040.1.2.28.3.2.1.1.2 | OCTET STRING | read-write | Description of the sensor. |
| OCT wtWebGraphAnalog57661PortOffset1 | 1.3.6.1.4.1.5040.1.2.28.3.2.1.1.3 | OCTET STRING | read-write | Offset calibration: Offset in degrees with maximum 3 decimal places at set point 1. |
| OCT wtWebGraphAnalog57661SetPoint1 | 1.3.6.1.4.1.5040.1.2.28.3.2.1.1.4 | OCTET STRING | read-write | Offset calibration: Reference set point 1 in degrees with maximum 3 decimal places. |
| OCT wtWebGraphAnalog57661PortOffset2 | 1.3.6.1.4.1.5040.1.2.28.3.2.1.1.5 | OCTET STRING | read-write | Offset calibration: Offset in degrees with maximum 3 decimal places at set point 2. |
| OCT wtWebGraphAnalog57661SetPoint2 | 1.3.6.1.4.1.5040.1.2.28.3.2.1.1.6 | OCTET STRING | read-write | Offset calibration: Reference set point 2 in degrees with maximum 3 decimal places. |
| OCT wtWebGraphAnalog57661PortComment | 1.3.6.1.4.1.5040.1.2.28.3.2.1.1.7 | OCTET STRING | read-write | Offset calibration: informations of date, name of operator, reference devices. |
| OCT wtWebGraphAnalog57661PortSensorSelect | 1.3.6.1.4.1.5040.1.2.28.3.2.1.1.8 | OCTET STRING | read-write | Binary coded options for sensor 1: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : 0-20mA (default) Bit 1 : 4-20mA Bit 2 : Disconnect Bit 3-7: unused |
| OCT wtWebGraphAnalog57661PortUnit | 1.3.6.1.4.1.5040.1.2.28.3.2.1.1.9 | OCTET STRING | read-write | User scale: displayed unit. |
| OCT wtWebGraphAnalog57661PortScale0 | 1.3.6.1.4.1.5040.1.2.28.3.2.1.1.10 | OCTET STRING | read-write | User scale: displayed value in 1/1000 at 0% full scale range. Range: -999999.999 to 999999.999 |
| OCT wtWebGraphAnalog57661PortScale100 | 1.3.6.1.4.1.5040.1.2.28.3.2.1.1.11 | OCTET STRING | read-write | User scale: displayed value in 1/1000 at 100% full scale range. Range: -999999.999 to 999999.999 |
| OCT wtWebGraphAnalog57661PortOutputMode | 1.3.6.1.4.1.5040.1.2.28.3.2.1.1.12 | OCTET STRING | read-write | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. If an output mode is selected, Bit 2 in wtWebGraphAnalog57661PortInputMode will be set automatically. The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 6-7: unused Bit 5 : Output OFF Bit 4 : Binary 2 Bit 3 : Binary 1 Bit 2 : SNMP Bit 1 : UDP ASCII Bit 0 : HTTP |
| OCT wtWebGraphAnalog57661PortInputMode | 1.3.6.1.4.1.5040.1.2.28.3.2.1.1.13 | OCTET STRING | read-write | This binary coded input mode defines the individual operation mode for any input. More than one mode must not be selected. If an input mode is selected, Bit 5 in wtWebGraphAnalog57661PortOutputMode will be set automatically. The OCTETS are interpreted bit-by-bit,Bit 0 corresponds to the LSB. OCTET 1: ungenutzt OCTET 2: ungenutzt OCTET 3: ungenutzt OCTET 4: Bit 3-7: unused Bit 2 : I-Output Bit 1 : I-Input, active Bit 0 : I-Input, passive |
| wtWebGraphAnalog57661Manufact | 1.3.6.1.4.1.5040.1.2.28.3.3 | |||
| OCT wtWebGraphAnalog57661MfName | 1.3.6.1.4.1.5040.1.2.28.3.3.1 | OCTET STRING | read-write | Manufacturer company name |
| OCT wtWebGraphAnalog57661MfAddr | 1.3.6.1.4.1.5040.1.2.28.3.3.2 | OCTET STRING | read-write | Manufacturer address. |
| OCT wtWebGraphAnalog57661MfHotline | 1.3.6.1.4.1.5040.1.2.28.3.3.3 | OCTET STRING | read-write | Manufacturer hotline. |
| OCT wtWebGraphAnalog57661MfInternet | 1.3.6.1.4.1.5040.1.2.28.3.3.4 | OCTET STRING | read-write | Manufacturer Internet address. |
| OCT wtWebGraphAnalog57661MfDeviceTyp | 1.3.6.1.4.1.5040.1.2.28.3.3.5 | OCTET STRING | read-write | Manufacturer device name (model number). |
| OCT wtWebGraphAnalog57661MfOrderNo | 1.3.6.1.4.1.5040.1.2.28.3.3.6 | OCTET STRING | read-write | Manufacturer part number. |
| wtWebGraphAnalog57661Diag | 1.3.6.1.4.1.5040.1.2.28.4 | |||
| INT wtWebGraphAnalog57661DiagErrorCount | 1.3.6.1.4.1.5040.1.2.28.4.1 | INTEGER | read-only | Number of entries in the error memory. |
| OCT wtWebGraphAnalog57661DiagBinaryError | 1.3.6.1.4.1.5040.1.2.28.4.2 | OCTET STRING | read-only | Error causes coded bit-by-bit. |
| INT wtWebGraphAnalog57661DiagErrorIndex | 1.3.6.1.4.1.5040.1.2.28.4.3 | INTEGER | read-write | The value of this variable is used as an index to read an error massege from wtWebGraphAnalog57661DiagErrorMessage. Errors are numbered from 1 to wtWebGraphAnalog57661DiagErrorCount. Writing a valid value into this variable, making the appropriate message readable from wtWebGraphAnalog57661DiagErrorMessage. |
| OCT wtWebGraphAnalog57661DiagErrorMessage | 1.3.6.1.4.1.5040.1.2.28.4.4 | OCTET STRING | read-only | Using wtWebGraphAnalog57661DiagErrorIndex as an index, the appropriate message is available. |
| INT wtWebGraphAnalog57661DiagErrorClear | 1.3.6.1.4.1.5040.1.2.28.4.5 | INTEGER | write-only | Writing 1 into this variable clears all diagnosis messages. |
RFC description
SNMP MIB for WebGraph AnalogIO device (model 57661) providing monitoring and management of analog input/output interfaces through SNMP.
Start monitoring WebGraph model 57661 analog I/O module (analog-channel reading/binary-threshold status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.