All MIBs › WebGraph-AnalogIO-57662-US-MIB
Category: Power and Environmental Monitoring
Description: Manages WebGraph model 57662 analog I/O device channels, sensor readings, output settings, and alarm states.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is WebGraph-AnalogIO-57662-US-MIB?
WebGraph-AnalogIO-57662-US-MIB is a vendor MIB for the WebGraph model 57662 analog/binary I/O monitoring device, a small SNMP-managed sensor interface unit. It exposes per-channel sensor configuration and readings, binary (digital) I/O values, and session-control settings such as a password and configuration mode. As a monitoring tool it is used almost entirely for environmental/hardware sensor status: reading analog sensor values (e.g., temperature, voltage, or other transducer inputs wired into the unit) per channel, along with binary input/output states used for alarm contacts or relay control, making it a hardware-status/environmental-monitoring MIB rather than a networking-protocol MIB. It is a self-contained proprietary module with no apparent dependency on external standard MIBs. It is deployed in facilities, equipment-room, or industrial settings where the WebGraph 57662 unit is wired to external sensors and provides remote SNMP-based environmental/alarm monitoring. Engineers can download the WebGraph-AnalogIO-57662-US-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in WebGraph-AnalogIO-57662-US-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- WebGraph model 57662 analog/binary I/O monitoring unit
Monitoring Examples
An operator polls wtWebGraphAnalog57662SensorTable/wtWebGraphAnalog57662SensorEntry keyed by wtWebGraphAnalog57662SensorNo to enumerate configured sensor channels, then reads wtWebGraphAnalog57662ValuesTable/wtWebGraphAnalog57662Values to get the current analog reading for each channel, such as a temperature or voltage sensor drifting outside its normal range. The wtWebGraphAnalog57662BinaryValuesTable/wtWebGraphAnalog57662BinaryValues objects would be checked to see if a digital alarm contact (e.g., door-open or leak-detection input) has changed state, while wtWebGraphAnalog57662SessCntrlConfigMode indicates whether the unit is currently in a configuration-change session.
What Can Be Monitored
- per-channel analog sensor readings
- binary/digital I/O state
- sensor channel configuration
- session control/config mode status
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| IpAddress | |
| NetworkAddress | |
| TimeTicks | |
| enterprises |
From RFC1213-MIB
| DisplayString | |
| PhysAddress |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| wut | 1.3.6.1.4.1.5040 | |||
| wtComServer | 1.3.6.1.4.1.5040.1 | |||
| wtWebio | 1.3.6.1.4.1.5040.1.2 | |||
| wtWebGraphAnalog57662 | 1.3.6.1.4.1.5040.1.2.29 | |||
| NTF wtWebGraphAnalog57662Alert1 | 1.3.6.1.4.1.5040.1.2.29.0.31 | This SNMP trap is generated when Alarm 1 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert2 | 1.3.6.1.4.1.5040.1.2.29.0.32 | This SNMP trap is generated when Alarm 2 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert3 | 1.3.6.1.4.1.5040.1.2.29.0.33 | This SNMP trap is generated when Alarm 3 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert4 | 1.3.6.1.4.1.5040.1.2.29.0.34 | This SNMP trap is generated when Alarm 4 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert5 | 1.3.6.1.4.1.5040.1.2.29.0.35 | This SNMP trap is generated when Alarm 5 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert6 | 1.3.6.1.4.1.5040.1.2.29.0.36 | This SNMP trap is generated when Alarm 6 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert7 | 1.3.6.1.4.1.5040.1.2.29.0.37 | This SNMP trap is generated when Alarm 7 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert8 | 1.3.6.1.4.1.5040.1.2.29.0.38 | This SNMP trap is generated when Alarm 8 was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662AlertReport | 1.3.6.1.4.1.5040.1.2.29.0.39 | This SNMP trap is generated when the report was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert9 | 1.3.6.1.4.1.5040.1.2.29.0.91 | This SNMP trap is generated when Alarm 1 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert10 | 1.3.6.1.4.1.5040.1.2.29.0.92 | This SNMP trap is generated when Alarm 2 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert11 | 1.3.6.1.4.1.5040.1.2.29.0.93 | This SNMP trap is generated when Alarm 3 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert12 | 1.3.6.1.4.1.5040.1.2.29.0.94 | This SNMP trap is generated when Alarm 4 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert13 | 1.3.6.1.4.1.5040.1.2.29.0.95 | This SNMP trap is generated when Alarm 5 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert14 | 1.3.6.1.4.1.5040.1.2.29.0.96 | This SNMP trap is generated when Alarm 6 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert15 | 1.3.6.1.4.1.5040.1.2.29.0.97 | This SNMP trap is generated when Alarm 7 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662Alert16 | 1.3.6.1.4.1.5040.1.2.29.0.98 | This SNMP trap is generated when Alarm 8 was cleared, SNMP trap enable is set and SNMP is enabled. | ||
| NTF wtWebGraphAnalog57662AlertDiag | 1.3.6.1.4.1.5040.1.2.29.0.110 | This SNMP trap is generated when a diagnosis/error message was triggered, SNMP trap enable is set and SNMP is enabled. | ||
| wtWebGraphAnalog57662Inventory | 1.3.6.1.4.1.5040.1.2.29.1 | |||
| INT wtWebGraphAnalog57662Sensors | 1.3.6.1.4.1.5040.1.2.29.1.1 | INTEGER | read-only | Number of sensors |
| wtWebGraphAnalog57662SensorTable | 1.3.6.1.4.1.5040.1.2.29.1.2 | not-accessible | List of sensors. | |
| wtWebGraphAnalog57662SensorEntry | 1.3.6.1.4.1.5040.1.2.29.1.2.1 | not-accessible | List of sensor numbers. | |
| INT wtWebGraphAnalog57662SensorNo | 1.3.6.1.4.1.5040.1.2.29.1.2.1.1 | INTEGER | read-only | Sensor number. |
| wtWebGraphAnalog57662ValuesTable | 1.3.6.1.4.1.5040.1.2.29.1.3 | not-accessible | List of measurement values corresponding to the channel numbers. | |
| wtWebGraphAnalog57662ValuesEntry | 1.3.6.1.4.1.5040.1.2.29.1.3.1 | not-accessible | Measurement values of the sensors. | |
| OCT wtWebGraphAnalog57662Values | 1.3.6.1.4.1.5040.1.2.29.1.3.1.1 | OCTET STRING | read-write | Measurement value of the sensor, ASCII. This value will be translated according to the ports settings for the read and write operations. |
| wtWebGraphAnalog57662BinaryValuesTable | 1.3.6.1.4.1.5040.1.2.29.1.4 | not-accessible | List of binary measurement values corresponding to the channel numbers. | |
| wtWebGraphAnalog57662BinaryValuesEntry | 1.3.6.1.4.1.5040.1.2.29.1.4.1 | not-accessible | Binary measurement values of the sensors. | |
| INT wtWebGraphAnalog57662BinaryValues | 1.3.6.1.4.1.5040.1.2.29.1.4.1.1 | INTEGER | read-write | Binary measurement value of the sensor in 1/1000, signed number, 0x7FFFFFFF indicates an invalid value. This value will be translated according to the ports settings for the read and write operations. |
| wtWebGraphAnalog57662SessCntrl | 1.3.6.1.4.1.5040.1.2.29.2 | |||
| OCT wtWebGraphAnalog57662SessCntrlPassword | 1.3.6.1.4.1.5040.1.2.29.2.1 | OCTET STRING | read-write | Entering this password opens a session which is ended by writing a 1 to wtWebGraphAnalog57662SessCntrlLogout. When read this variable provides a string of length zero. |
| INT wtWebGraphAnalog57662SessCntrlConfigMode | 1.3.6.1.4.1.5040.1.2.29.2.2 | INTEGER | read-only | When the device is in SNMP configuration mode, the value 1 is returned, otherwise 0. If the read value is 0 even though the password was written, the device is already in config mode and the variables can only be read. |
| INT wtWebGraphAnalog57662SessCntrlLogout | 1.3.6.1.4.1.5040.1.2.29.2.3 | INTEGER | read-write | If the device is in configuration mode and the session was opened by this SNMP Manager, writing a 1 to this variable will end the session and all parameters are stored. Writing a 2 discards all entries again. When read this variable provides the value 0. |
| OCT wtWebGraphAnalog57662SessCntrlAdminPassword | 1.3.6.1.4.1.5040.1.2.29.2.4 | OCTET STRING | read-write | This password protects access to the variables with administrator rights. It can only be changed by the administrator. If no password was assigned, the valid password is public. |
| OCT wtWebGraphAnalog57662SessCntrlConfigPassword | 1.3.6.1.4.1.5040.1.2.29.2.5 | OCTET STRING | read-write | This password protects access to the variables with configurator rights. It can be changed by the administrator and by the configurator. If no password was assigned, the valid password is public. When read this variable provides a null-pointer. |
| wtWebGraphAnalog57662Config | 1.3.6.1.4.1.5040.1.2.29.3 | |||
| wtWebGraphAnalog57662Device | 1.3.6.1.4.1.5040.1.2.29.3.1 | |||
| wtWebGraphAnalog57662Text | 1.3.6.1.4.1.5040.1.2.29.3.1.1 | |||
| OCT wtWebGraphAnalog57662DeviceName | 1.3.6.1.4.1.5040.1.2.29.3.1.1.1 | OCTET STRING | read-write | Name of the Webio, which is user definable. |
| OCT wtWebGraphAnalog57662DeviceText | 1.3.6.1.4.1.5040.1.2.29.3.1.1.2 | OCTET STRING | read-write | Description of the Webio, which is user definable. |
| OCT wtWebGraphAnalog57662DeviceLocation | 1.3.6.1.4.1.5040.1.2.29.3.1.1.3 | OCTET STRING | read-write | Description of the location of the Webio, which is user definable. |
| OCT wtWebGraphAnalog57662DeviceContact | 1.3.6.1.4.1.5040.1.2.29.3.1.1.4 | OCTET STRING | read-write | Contact address of the system operator of the Webio, which is user definable. |
| wtWebGraphAnalog57662TimeDate | 1.3.6.1.4.1.5040.1.2.29.3.1.2 | |||
| wtWebGraphAnalog57662TimeZone | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1 | |||
| INT wtWebGraphAnalog57662TzOffsetHrs | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.1 | INTEGER | read-write | Offset hours for the time zone (winter time) with respect to UTC. |
| INT wtWebGraphAnalog57662TzOffsetMin | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.2 | INTEGER | read-write | Offset minutes for the time zone (winter time) with respect to UTC. |
| OCT wtWebGraphAnalog57662TzEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.3 | OCTET STRING | read-write | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Timezone |
| INT wtWebGraphAnalog57662StTzOffsetHrs | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.4 | INTEGER | read-write | Offset hours of the time zone (summer time) with respect to UTC. |
| INT wtWebGraphAnalog57662StTzOffsetMin | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.5 | INTEGER | read-write | Offset minutes of the time zone (summer time) with respect to UTC. |
| OCT wtWebGraphAnalog57662StTzEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.6 | OCTET STRING | read-write | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Summertime |
| INT wtWebGraphAnalog57662StTzStartMonth | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.7 | INTEGER | read-write | Month in which the change is made from winter time to summer time. |
| INT wtWebGraphAnalog57662StTzStartMode | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.8 | INTEGER | read-write | Mode of the day of the week for which the change is made from winter time to summer time. |
| INT wtWebGraphAnalog57662StTzStartWday | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.9 | INTEGER | read-write | Day of the week on which the change is made from winter time to summer time |
| INT wtWebGraphAnalog57662StTzStartHrs | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.10 | INTEGER | read-write | Hour in which the time zone is changed from winter to summer time with respect to UTC. |
| INT wtWebGraphAnalog57662StTzStartMin | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.11 | INTEGER | read-write | Minute in which the time zone is changed from winter to summer time with respect to UTC. |
| INT wtWebGraphAnalog57662StTzStopMonth | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.12 | INTEGER | read-write | Month in which the change is made from summer time to winter time. |
| INT wtWebGraphAnalog57662StTzStopMode | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.13 | INTEGER | read-write | Mode of the week day on which the change is made from summer time to winter time. |
| INT wtWebGraphAnalog57662StTzStopWday | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.14 | INTEGER | read-write | Day of the week on which the change is made from summer time to winter time. |
| INT wtWebGraphAnalog57662StTzStopHrs | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.15 | INTEGER | read-write | Hour at which the time zone is changed from summer to winter time with respect to UTC. |
| INT wtWebGraphAnalog57662StTzStopMin | 1.3.6.1.4.1.5040.1.2.29.3.1.2.1.16 | INTEGER | read-write | Minute at which the time zone is changed from summer to winter time with respect to UTC. |
| wtWebGraphAnalog57662TimeServer | 1.3.6.1.4.1.5040.1.2.29.3.1.2.2 | |||
| OCT wtWebGraphAnalog57662TimeServer1 | 1.3.6.1.4.1.5040.1.2.29.3.1.2.2.1 | OCTET STRING | read-write | IP address or name of the 1st time server in ASCII |
| OCT wtWebGraphAnalog57662TimeServer2 | 1.3.6.1.4.1.5040.1.2.29.3.1.2.2.2 | OCTET STRING | read-write | IP address or name of the 2nd time server in ASCII |
| OCT wtWebGraphAnalog57662TsEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.2.2.3 | OCTET STRING | read-write | Binary coded conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Apply Time Server |
| INT wtWebGraphAnalog57662TsSyncTime | 1.3.6.1.4.1.5040.1.2.29.3.1.2.2.4 | INTEGER | read-write | Daily synchronisation time with the time server (hour: 0-23). |
| wtWebGraphAnalog57662DeviceClock | 1.3.6.1.4.1.5040.1.2.29.3.1.2.3 | |||
| INT wtWebGraphAnalog57662ClockHrs | 1.3.6.1.4.1.5040.1.2.29.3.1.2.3.1 | INTEGER | read-write | Clock hours taking into account the time zone settings. |
| INT wtWebGraphAnalog57662ClockMin | 1.3.6.1.4.1.5040.1.2.29.3.1.2.3.2 | INTEGER | read-write | Clock minutes taking into account the time zone settings. |
| INT wtWebGraphAnalog57662ClockDay | 1.3.6.1.4.1.5040.1.2.29.3.1.2.3.3 | INTEGER | read-write | Date: Day of the month, taking into account the time zone settings. |
| INT wtWebGraphAnalog57662ClockMonth | 1.3.6.1.4.1.5040.1.2.29.3.1.2.3.4 | INTEGER | read-write | Date: Month, taking into account the time zone settings. |
| INT wtWebGraphAnalog57662ClockYear | 1.3.6.1.4.1.5040.1.2.29.3.1.2.3.5 | INTEGER | read-write | Date: Year, taking into account the time zone settings. |
| wtWebGraphAnalog57662Basic | 1.3.6.1.4.1.5040.1.2.29.3.1.3 | |||
| wtWebGraphAnalog57662Network | 1.3.6.1.4.1.5040.1.2.29.3.1.3.1 | |||
| IP wtWebGraphAnalog57662IpAddress | 1.3.6.1.4.1.5040.1.2.29.3.1.3.1.1 | IpAddress | read-write | IP address of the Webio |
| IP wtWebGraphAnalog57662SubnetMask | 1.3.6.1.4.1.5040.1.2.29.3.1.3.1.2 | IpAddress | read-write | Subnet mask of the Webio |
| IP wtWebGraphAnalog57662Gateway | 1.3.6.1.4.1.5040.1.2.29.3.1.3.1.3 | IpAddress | read-write | Gateway of the Webio |
| OCT wtWebGraphAnalog57662DnsServer1 | 1.3.6.1.4.1.5040.1.2.29.3.1.3.1.4 | OCTET STRING | read-write | IP address of the 1st DNS server in ASCII |
| OCT wtWebGraphAnalog57662DnsServer2 | 1.3.6.1.4.1.5040.1.2.29.3.1.3.1.5 | OCTET STRING | read-write | IP address of the 2nd DNS server in ASCII |
| OCT wtWebGraphAnalog57662AddConfig | 1.3.6.1.4.1.5040.1.2.29.3.1.3.1.6 | OCTET STRING | read-write | Additional configuration (1=ON): Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: DHCP disable Bit 0: BOOTP disable |
| wtWebGraphAnalog57662HTTP | 1.3.6.1.4.1.5040.1.2.29.3.1.3.2 | |||
| OCT wtWebGraphAnalog57662Startup | 1.3.6.1.4.1.5040.1.2.29.3.1.3.2.1 | OCTET STRING | read-write | Binary coded start page: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1: Index.htm Bit 2: Home.htm Bit 3: User.htm Only one page may be selected at a time. |
| OCT wtWebGraphAnalog57662GetHeaderEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.3.2.2 | OCTET STRING | read-write | If these bits are set, every answer of a short form GET question will be lead by the IP-address and name of the device and/or a HTTP header: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-6: unused Bit 1 : GET HTTP enable Bit 0 : GET Header enable |
| INT wtWebGraphAnalog57662HttpPort | 1.3.6.1.4.1.5040.1.2.29.3.1.3.2.3 | INTEGER | read-write | Definition of the standard HTML port (Default: 80). |
| wtWebGraphAnalog57662Mail | 1.3.6.1.4.1.5040.1.2.29.3.1.3.3 | |||
| OCT wtWebGraphAnalog57662MailAdName | 1.3.6.1.4.1.5040.1.2.29.3.1.3.3.1 | OCTET STRING | read-write | Device name for mail administration. |
| OCT wtWebGraphAnalog57662MailReply | 1.3.6.1.4.1.5040.1.2.29.3.1.3.3.2 | OCTET STRING | read-write | Reply address for the mail server. |
| OCT wtWebGraphAnalog57662MailServer | 1.3.6.1.4.1.5040.1.2.29.3.1.3.3.3 | OCTET STRING | read-write | Name or IP address of the mail server. |
| OCT wtWebioAn1MailEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.3.3.4 | OCTET STRING | read-write | Set this bit to enable the sending of mails: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Mail enable |
| OCT wtWebGraphAnalog57662MailAuthentication | 1.3.6.1.4.1.5040.1.2.29.3.1.3.3.5 | OCTET STRING | read-write | Selection of the authentication modi: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 3-7: unused Bit 2 : POP3 before SMTP Bit 1 : ESMTP, authentication Bit 0 : SMTP, no authentication |
| OCT wtWebGraphAnalog57662MailAuthUser | 1.3.6.1.4.1.5040.1.2.29.3.1.3.3.6 | OCTET STRING | read-write | Name of the user to be authenticated. |
| OCT wtWebGraphAnalog57662MailAuthPassword | 1.3.6.1.4.1.5040.1.2.29.3.1.3.3.7 | OCTET STRING | read-write | Authentication password. |
| OCT wtWebGraphAnalog57662MailPop3Server | 1.3.6.1.4.1.5040.1.2.29.3.1.3.3.8 | OCTET STRING | read-write | Name or Ip-address of the POP3 Servers. |
| wtWebGraphAnalog57662SNMP | 1.3.6.1.4.1.5040.1.2.29.3.1.3.4 | |||
| OCT wtWebGraphAnalog57662SnmpCommunityStringRead | 1.3.6.1.4.1.5040.1.2.29.3.1.3.4.1 | OCTET STRING | read-write | Community string read only |
| OCT wtWebGraphAnalog57662SnmpCommunityStringReadWrite | 1.3.6.1.4.1.5040.1.2.29.3.1.3.4.2 | OCTET STRING | read-write | Community string read / write |
| OCT wtWebGraphAnalog57662SystemTrapManagerIP | 1.3.6.1.4.1.5040.1.2.29.3.1.3.4.3 | OCTET STRING | read-write | Name or IP address of the TCP server which accepts the system trap. |
| OCT wtWebGraphAnalog57662SystemTrapEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.3.4.4 | OCTET STRING | read-write | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2-7: unused |
| OCT wtWebGraphAnalog57662SnmpEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.3.4.5 | OCTET STRING | read-write | Set bit 0 to enable SNMP. If disabled, the device did not respond to any SNMP requests. Bit 1 decided wether the community string of read operations is compared with the system password or not: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : SNMP enable |
| OCT wtWebGraphAnalog57662SnmpCommunityStringTrap | 1.3.6.1.4.1.5040.1.2.29.3.1.3.4.6 | OCTET STRING | read-write | Community string send within traps. |
| wtWebGraphAnalog57662UDP | 1.3.6.1.4.1.5040.1.2.29.3.1.3.5 | |||
| INT wtWebGraphAnalog57662UdpPort | 1.3.6.1.4.1.5040.1.2.29.3.1.3.5.1 | INTEGER | read-write | Udp port to which the Udp queries ( short form GET requests) can be sent. This port number must be unique within the device. |
| OCT wtWebGraphAnalog57662UdpEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.3.5.2 | OCTET STRING | read-write | Set this bit to enable UDP support: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : UDP enable |
| wtWebGraphAnalog57662Syslog | 1.3.6.1.4.1.5040.1.2.29.3.1.3.6 | |||
| OCT wtWebGraphAnalog57662SyslogServerIP | 1.3.6.1.4.1.5040.1.2.29.3.1.3.6.1 | OCTET STRING | read-write | Name or IP address of the Syslog server, which accepts the Syslog messgaes. |
| INT wtWebGraphAnalog57662SyslogServerPort | 1.3.6.1.4.1.5040.1.2.29.3.1.3.6.2 | INTEGER | read-write | Portnumber of the Syslog servers, default 514. |
| OCT wtWebGraphAnalog57662SyslogSystemMessagesEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.3.6.3 | OCTET STRING | read-write | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: ColdStart Bit 1: WarmStart Bit 2: Diag Messages Bit 3-7: unused |
| OCT wtWebGraphAnalog57662SyslogEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.3.6.4 | OCTET STRING | read-write | Set bit 0to enable Syslog: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Syslog enable |
| wtWebGraphAnalog57662FTP | 1.3.6.1.4.1.5040.1.2.29.3.1.3.7 | |||
| OCT wtWebGraphAnalog57662FTPServerIP | 1.3.6.1.4.1.5040.1.2.29.3.1.3.7.1 | OCTET STRING | read-write | Name or IP address of the FTP server, which accepts the FTP messages. |
| INT wtWebGraphAnalog57662FTPServerControlPort | 1.3.6.1.4.1.5040.1.2.29.3.1.3.7.2 | INTEGER | read-write | Portnumber of the control port of the FTP server, default 21. |
| OCT wtWebGraphAnalog57662FTPUserName | 1.3.6.1.4.1.5040.1.2.29.3.1.3.7.3 | OCTET STRING | read-write | FTP Loggin: user name. |
| OCT wtWebGraphAnalog57662FTPPassword | 1.3.6.1.4.1.5040.1.2.29.3.1.3.7.4 | OCTET STRING | read-write | FTP Loggin: user password. |
| OCT wtWebGraphAnalog57662FTPAccount | 1.3.6.1.4.1.5040.1.2.29.3.1.3.7.5 | OCTET STRING | read-write | FTP Loggin: name of account. |
| OCT wtWebGraphAnalog57662FTPOption | 1.3.6.1.4.1.5040.1.2.29.3.1.3.7.6 | OCTET STRING | read-write | Bit 0 switches the FTP Server in Passiv-Mode, the Client controls the data connection on its own: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : PASV enable |
| OCT wtWebGraphAnalog57662FTPEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.3.7.7 | OCTET STRING | read-write | Set Bit 0 to enable FTP: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : FTP enable |
| wtWebGraphAnalog57662Language | 1.3.6.1.4.1.5040.1.2.29.3.1.3.8 | |||
| OCT wtWebGraphAnalog57662LanguageSelect | 1.3.6.1.4.1.5040.1.2.29.3.1.3.8.1 | OCTET STRING | read-write | Language selection: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 2-7: unused Bit 1 : English Bit 0 : German |
| wtWebGraphAnalog57662Binary | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9 | |||
| INT wtWebGraphAnalog57662BinaryModeCount | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.1 | INTEGER | read-only | Number of independent binary channels. |
| wtWebGraphAnalog57662BinaryIfTable | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.2 | not-accessible | Table of indices. | |
| wtWebGraphAnalog57662BinaryIfEntry | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.2.1 | not-accessible | Indices of the binary channels. | |
| INT wtWebGraphAnalog57662BinaryModeNo | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.2.1.1 | INTEGER | read-only | Number of the binary channel. |
| wtWebGraphAnalog57662BinaryTable | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3 | not-accessible | Table of properties of the binary mode. | |
| wtWebGraphAnalog57662BinaryEntry | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1 | not-accessible | Binary properties. | |
| OCT wtWebGraphAnalog57662BinaryOperationMode | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.1 | OCTET STRING | read-write | Selection of the operation mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 3-7: unused Bit 2 : UDP Peer Bit 1 : TCP Client Bit 0 : TCP Server |
| INT wtWebGraphAnalog57662BinaryTcpServerLocalPort | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.2 | INTEGER | read-write | Local TCP port for data exchange in this server mode. This port number must be unique within the device. Reserved port number must not be used (refere to the manual). |
| OCT wtWebGraphAnalog57662BinaryTcpServerInputTrigger | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.3 | OCTET STRING | read-write | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rule. Nevertheless every transmission will contain all input states. If a bit is set (1), a change of state on the corresponding input triggers a transmission. If the bit is not set (0), no transmission takes place. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 0-1: Analog inputs 0-1 |
| OCT wtWebGraphAnalog57662BinaryTcpServerApplicationMode | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.4 | OCTET STRING | read-write | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 4-7: unused Bit 3 : OPC Device Bit 2 : Box2Box Slave Bit 1 : Compatible 50xxx Bit 0 : Default |
| INT wtWebGraphAnalog57662BinaryTcpClientLocalPort | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.5 | INTEGER | read-write | Local TCP port for data exchange in this client mode. This port number must be unique within the device. Reserved port number must not be used (refere to the manual). |
| INT wtWebGraphAnalog57662BinaryTcpClientServerPort | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.6 | INTEGER | read-write | Port number of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting the server port to zero. |
| OCT wtWebGraphAnalog57662BinaryTcpClientServerIpAddr | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.7 | OCTET STRING | read-write | Ip address of the server. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting the server IP address to 0.0.0.0. |
| OCT wtWebGraphAnalog57662BinaryTcpClientServerPassword | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.8 | OCTET STRING | read-write | Building a connection may be protected by the administrator password of the server. Enter the server password to establish the connection, if a server administrator password exists. |
| INT wtWebGraphAnalog57662BinaryTcpClientInactivity | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.9 | INTEGER | read-write | Connection timeout in 100ms. If no data are exchanged within the specified time, the device closes the connection to the server. The value 0 deactivates the timer. Using the Box2Box mode this function is disabled. |
| OCT wtWebGraphAnalog57662BinaryTcpClientInputTrigger | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.10 | OCTET STRING | read-write | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rule. Nevertheless every transmission will contain all input states. If a bit is set (1), a change of state on the corresponding input triggers a transmission. If the bit is not set (0), no transmission takes place. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 0-1: Analog inputs 0-1 |
| INT wtWebGraphAnalog57662BinaryTcpClientInterval | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.11 | INTEGER | read-write | Configurable interval with a 100ms base, in which the Webio device sends data to the configured application. A interval of zero stopps the periodical sending. |
| OCT wtWebGraphAnalog57662BinaryTcpClientApplicationMode | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.12 | OCTET STRING | read-write | Selection of the application mode: The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 3-7: unused Bit 2 : Box2Box Slave Bit 1 : Compatible 50xxx Bit 0 : Default |
| INT wtWebGraphAnalog57662BinaryUdpPeerLocalPort | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.13 | INTEGER | read-write | Local UDP port for data exchange in this peer to peer mode. This port number must be unique within the device. Reserved port number must not be used (refere to the manual). |
| INT wtWebGraphAnalog57662BinaryUdpPeerRemotePort | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.14 | INTEGER | read-write | Port number of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting the remote port to zero. |
| OCT wtWebGraphAnalog57662BinaryUdpPeerRemoteIpAddr | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.15 | OCTET STRING | read-write | Ip address of the remote device. A complete set of port number, IP address and a valid input/output mask starts this mode. No data exchange take place when setting the remote device IP address to 0.0.0.0. |
| OCT wtWebGraphAnalog57662BinaryUdpPeerInputTrigger | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.16 | OCTET STRING | read-write | Every change on the inputs causes their state to be transmitted to the remote device. To minimize data traffic, individual inputs may be exempted from this rule. Nevertheless every transmission will contain all input states. If a bit is set (1), a change of state on the corresponding input triggers a transmission. If the bit is not set (0), no transmission takes place. The OCTETS are interpreted bit-by-bit, with each bit corresponding to an input. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4, Bit 0-1: Analog inputs 0-1 |
| INT wtWebGraphAnalog57662BinaryUdpPeerInterval | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.17 | INTEGER | read-write | Configurable interval with a 100ms base, in which the Webio device sends data to the configured remote device. A interval of zero stopps the periodical sending. |
| OCT wtWebGraphAnalog57662BinaryUdpPeerApplicationMode | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.18 | OCTET STRING | read-write | Selection of the application mode: The OCTETS are interpreted bit-by-bit, with each bit corresponding to an output. Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 3-7: unused Bit 2 : Box2Box Slave Bit 1 : Compatible 50xxx Bit 0 : Default |
| INT wtWebGraphAnalog57662BinaryConnectedPort | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.19 | INTEGER | read-only | Port number of the remote device, after connection has been established. In case of no connection or missing port informations a zero will be read. |
| IP wtWebGraphAnalog57662BinaryConnectedIpAddr | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.20 | IpAddress | read-only | IP address of the remote device, after connection has been established. In case of no connection or missing port informations 0.0.0.0 will be read. |
| INT wtWebGraphAnalog57662BinaryTcpServerClientHttpPort | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.21 | INTEGER | read-write | HTTP port number of the remote device at TCP Server Mode. If an mailfunction occurs status informations will be send to this port. Not used at mode Compatible 50xxx. |
| INT wtWebGraphAnalog57662BinaryTcpClientServerHttpPort | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.22 | INTEGER | read-write | HTTP port number of the remote device at TCP Client Mode. In the operating mode Box2Box connection status informations will be exchanged through this port. |
| OCT wtWebGraphAnalog57662BinaryTcpServerHysteresis1 | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.23 | OCTET STRING | read-write | A change greater than this value initiate a transmission of the corresponding input value. The input 1 must be selected at wtWebGraphAnalog57662BinaryTcpServerInputTrigger. With a hysteresis of zero any change will be transmitted. |
| OCT wtWebGraphAnalog57662BinaryTcpServerHysteresis2 | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.24 | OCTET STRING | read-write | A change greater than this value initiate a transmission of the corresponding input value. The input 2 must be selected at wtWebGraphAnalog57662BinaryTcpServerInputTrigger. With a hysteresis of zero any change will be transmitted. |
| OCT wtWebGraphAnalog57662BinaryTcpClientHysteresis1 | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.25 | OCTET STRING | read-write | A change greater than this value initiate a transmission of the corresponding input value. The input 1 must be selected at wtWebGraphAnalog57662BinaryTcpClientInputTrigger. With a hysteresis of zero any change will be transmitted. |
| OCT wtWebGraphAnalog57662BinaryTcpClientHysteresis2 | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.26 | OCTET STRING | read-write | A change greater than this value initiate a transmission of the corresponding input value. The input 2 must be selected at wtWebGraphAnalog57662BinaryTcpClientInputTrigger. With a hysteresis of zero any change will be transmitted. |
| OCT wtWebGraphAnalog57662BinaryUdpPeerHysteresis1 | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.27 | OCTET STRING | read-write | A change greater than this value initiate a transmission of the corresponding input value. The input 1 must be selected at wtWebGraphAnalog57662BinaryUdpPeerInputTrigger. With a hysteresis of zero any change will be transmitted. |
| OCT wtWebGraphAnalog57662BinaryUdpPeerHysteresis2 | 1.3.6.1.4.1.5040.1.2.29.3.1.3.9.3.1.28 | OCTET STRING | read-write | A change greater than this value initiate a transmission of the corresponding input value. The input 2 must be selected at wtWebGraphAnalog57662BinaryUdpPeerInputTrigger. With a hysteresis of zero any change will be transmitted. |
| wtWebGraphAnalog57662Datalogger | 1.3.6.1.4.1.5040.1.2.29.3.1.4 | |||
| INT wtWebGraphAnalog57662LoggerTimebase | 1.3.6.1.4.1.5040.1.2.29.3.1.4.1 | INTEGER | read-write | Time base of the data logger |
| OCT wtWebGraphAnalog57662LoggerSensorSel | 1.3.6.1.4.1.5040.1.2.29.3.1.4.2 | OCTET STRING | read-write | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 Bit 2-7: unused |
| OCT wtWebGraphAnalog57662DisplaySensorSel | 1.3.6.1.4.1.5040.1.2.29.3.1.4.3 | OCTET STRING | read-write | Binary coded sensor selection: only selected sensors will be shown in the graphical presentation: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 Bit 2-7: unused |
| wtWebGraphAnalog57662SensorColorTable | 1.3.6.1.4.1.5040.1.2.29.3.1.4.4 | not-accessible | List of sensor colors for the praphical presentation. | |
| wtWebGraphAnalog57662SensorColorEntry | 1.3.6.1.4.1.5040.1.2.29.3.1.4.4.1 | not-accessible | Index numbers of the sensors. | |
| OCT wtWebGraphAnalog57662SensorColor | 1.3.6.1.4.1.5040.1.2.29.3.1.4.4.1.1 | OCTET STRING | read-write | Color of the sensors at the praphical presention. |
| OCT wtWebGraphAnalog57662AutoScaleEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.4.5 | OCTET STRING | read-write | If bit 0 is set, vertical auto scale is enabled: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 1-7: unused Bit 0 : Auto Scale enable |
| OCT wtWebGraphAnalog57662VerticalUpperLimit | 1.3.6.1.4.1.5040.1.2.29.3.1.4.6 | OCTET STRING | read-write | This value defines the maximum temperature shown in the graphical presentation, if no auto scaling is selected. Temperature in degrees with maximum 2 decimal places. |
| OCT wtWebGraphAnalog57662VerticalLowerLimit | 1.3.6.1.4.1.5040.1.2.29.3.1.4.7 | OCTET STRING | read-write | This value defines the minimum temperature shown in the graphical presentation, if no auto scaling is selected. Temperature in degrees with maximum 2 decimal places. |
| INT wtWebGraphAnalog57662HorizontalZoom | 1.3.6.1.4.1.5040.1.2.29.3.1.4.8 | INTEGER | read-write | Defines the default zoom stage, if no auto scaling is selected. |
| wtWebGraphAnalog57662Alarm | 1.3.6.1.4.1.5040.1.2.29.3.1.5 | |||
| INT wtWebGraphAnalog57662AlarmCount | 1.3.6.1.4.1.5040.1.2.29.3.1.5.1 | INTEGER | read-only | Number of independent alarms. |
| wtWebGraphAnalog57662AlarmIfTable | 1.3.6.1.4.1.5040.1.2.29.3.1.5.2 | not-accessible | List of alarm indices. | |
| wtWebGraphAnalog57662AlarmIfEntry | 1.3.6.1.4.1.5040.1.2.29.3.1.5.2.1 | not-accessible | Numbers of the alarms. | |
| INT wtWebGraphAnalog57662AlarmNo | 1.3.6.1.4.1.5040.1.2.29.3.1.5.2.1.1 | INTEGER | read-only | Alarm number. |
| wtWebGraphAnalog57662AlarmTable | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3 | not-accessible | List of settings depending on the alarm number. | |
| wtWebGraphAnalog57662AlarmEntry | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1 | not-accessible | Alarm parameters of the individual alarms. | |
| OCT wtWebGraphAnalog57662AlarmTrigger | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.1 | OCTET STRING | read-write | Binary coded trigger conditions: Octet 1: unused Octet 2: unused Octet 3: Bit 0: Timer Bit 1: ColdStart Bit 2: WarmStart Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 Bit 2-7: unused |
| OCT wtWebGraphAnalog57662AlarmMin1 | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.2 | OCTET STRING | read-write | Minimum sensor 1 with maximum 3 decimal places. |
| OCT wtWebGraphAnalog57662AlarmMax1 | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.3 | OCTET STRING | read-write | Maximum sensor 1 with maximum 3 decimal places. |
| OCT wtWebGraphAnalog57662AlarmHysteresis1 | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.4 | OCTET STRING | read-write | Reading changes of this size clears the alarm state (MAX-hyst, MIN+hyst.) with maximum 3 decimal places. |
| OCT wtWebGraphAnalog57662AlarmDelay | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.5 | OCTET STRING | read-write | Alarm will be delayed by setting this time while stable alarm condition occur (time in minutes). |
| OCT wtWebGraphAnalog57662AlarmInterval | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.6 | OCTET STRING | read-write | Send interval for alarm messages. |
| OCT wtWebGraphAnalog57662AlarmEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.7 | OCTET STRING | read-write | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: TCP Client enable |
| OCT wtWebGraphAnalog57662AlarmEMailAddr | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.8 | OCTET STRING | read-write | E-Mail address for sending the alarm mail to. |
| OCT wtWebGraphAnalog57662AlarmMailSubject | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.9 | OCTET STRING | read-write | Subject line for alarm mail. |
| OCT wtWebGraphAnalog57662AlarmMailText | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.10 | OCTET STRING | read-write | Alarm mail text: provides the current temperature; n = 1..2. provides the current time. |
| OCT wtWebGraphAnalog57662AlarmManagerIP | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.11 | OCTET STRING | read-write | Name or IP address of the SNMP Manager which accepts the trap. |
| OCT wtWebGraphAnalog57662AlarmTrapText | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.12 | OCTET STRING | read-write | This text is sent in the trap body. |
| OCT wtWebGraphAnalog57662AlarmMailOptions | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.13 | OCTET STRING | read-write | Binary coded options: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Attach Thermo.csv Enable Bit 1 : CSV-Data_since_last_report Bit 2-7: unused |
| OCT wtWebGraphAnalog57662AlarmTcpIpAddr | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.14 | OCTET STRING | read-write | Name or IP address of the TCP server which accepts the trap. |
| INT wtWebGraphAnalog57662AlarmTcpPort | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.15 | INTEGER | read-write | Port number of the TCP server which accepts the trap. |
| OCT wtWebGraphAnalog57662AlarmTcpText | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.16 | OCTET STRING | read-write | This text is sent in the TCP trap body. |
| OCT wtWebGraphAnalog57662AlarmClearMailSubject | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.17 | OCTET STRING | read-write | Subject line for alarm clear mail. |
| OCT wtWebGraphAnalog57662AlarmClearMailText | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.18 | OCTET STRING | read-write | Alarm clear mail text: provides the current temperature; n = 1..2. provides the current time. |
| OCT wtWebGraphAnalog57662AlarmClearTrapText | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.19 | OCTET STRING | read-write | This text is sent in the trap body. |
| OCT wtWebGraphAnalog57662AlarmClearTcpText | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.20 | OCTET STRING | read-write | This text is sent in the TCP trap body. |
| OCT wtWebGraphAnalog57662AlarmMin2 | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.21 | OCTET STRING | read-write | Minimum sensor 2 with maximum 3 decimal places. |
| OCT wtWebGraphAnalog57662AlarmMax2 | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.22 | OCTET STRING | read-write | Maximum sensor 2 with maximum 2 decimal places. |
| OCT wtWebGraphAnalog57662AlarmHysteresis2 | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.23 | OCTET STRING | read-write | Hysterese rel. sensor 2 with maximum 3 decimal places. |
| OCT wtWebGraphAnalog57662AlarmSyslogIpAddr | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.24 | OCTET STRING | read-write | IP address of the syslog server to which the Webio device should send syslog messages. |
| INT wtWebGraphAnalog57662AlarmSyslogPort | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.25 | INTEGER | read-write | Port number of the syslog server to which the Webio device should send syslog messages. |
| OCT wtWebGraphAnalog57662AlarmSyslogText | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.26 | OCTET STRING | read-write | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| OCT wtWebGraphAnalog57662AlarmSyslogClearText | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.27 | OCTET STRING | read-write | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body of a alarm clear message. |
| OCT wtWebGraphAnalog57662AlarmFtpDataPort | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.28 | OCTET STRING | read-write | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| OCT wtWebGraphAnalog57662AlarmFtpFileName | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.29 | OCTET STRING | read-write | Name of the file including path informations. |
| OCT wtWebGraphAnalog57662AlarmFtpText | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.30 | OCTET STRING | read-write | Message text to store on the FTP server. |
| OCT wtWebGraphAnalog57662AlarmFtpClearText | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.31 | OCTET STRING | read-write | Alarm clear message to store on the FTP server. |
| OCT wtWebGraphAnalog57662AlarmFtpOption | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.32 | OCTET STRING | read-write | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : STORE Bit 1 : APPEND Bit 2-7: unused |
| OCT wtWebGraphAnalog57662AlarmTimerCron | 1.3.6.1.4.1.5040.1.2.29.3.1.5.3.1.33 | OCTET STRING | read-write | This entry defines a time window for alarm 1-8 and a activation time for the report. A time window is definied by start and stop time stamp, seperated by a space or tab. The activation time of the report is defined by a single start time stamp. Each time stamp contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger an action, weekday and day of month are interpreted separatley. 1: Minutes Range 0-59 2. Hours Range 0-23, 0 is midnight 3: Day of month Range 1-31 4: Month Range 1-12 5: Weekday Range 0-6, 0 is sunday Syntax for every field: - an asterix (*) enables every possible setting of a field - single numbers seperated by commas (i.e.: 2,14,22) - a partition within the allowed range (i.e.: 1-5) - step size within a partition of the allowed range (i.e.: 0-59/2 every second minute). |
| wtWebGraphAnalog57662Graphics | 1.3.6.1.4.1.5040.1.2.29.3.1.6 | |||
| wtWebGraphAnalog57662GraphicsBase | 1.3.6.1.4.1.5040.1.2.29.3.1.6.1 | |||
| OCT wtWebGraphAnalog57662GraphicsBaseEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.6.1.1 | OCTET STRING | read-write | Defines the viewing options of the graphic: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Auto scroll enable Bit 1 : Show table Bit 2 : Show graph Bit 3 : Show control buttons Bit 4 : Show config menu Bit 5-7: unused |
| INT wtWebGraphAnalog57662GraphicsBaseWidth | 1.3.6.1.4.1.5040.1.2.29.3.1.6.1.2 | INTEGER | read-write | Defines the width of the graphic in pixels. |
| INT wtWebGraphAnalog57662GraphicsBaseHeight | 1.3.6.1.4.1.5040.1.2.29.3.1.6.1.3 | INTEGER | read-write | Defines the height of the graphic in pixels. |
| OCT wtWebGraphAnalog57662GraphicsBaseFrameColor | 1.3.6.1.4.1.5040.1.2.29.3.1.6.1.4 | OCTET STRING | read-write | Frame color definition in RGB. |
| OCT wtWebGraphAnalog57662GraphicsBaseBackgroundColor | 1.3.6.1.4.1.5040.1.2.29.3.1.6.1.5 | OCTET STRING | read-write | Background color definition in RGB. |
| INT wtWebGraphAnalog57662GraphicsBasePollingrate | 1.3.6.1.4.1.5040.1.2.29.3.1.6.1.6 | INTEGER | read-write | Defines the pollingrate in seconds, which defines the refreshing intervall of the graphic. |
| wtWebGraphAnalog57662GraphicsSelect | 1.3.6.1.4.1.5040.1.2.29.3.1.6.2 | |||
| OCT wtWebGraphAnalog57662GraphicsSelectDisplaySensorSel | 1.3.6.1.4.1.5040.1.2.29.3.1.6.2.1 | OCTET STRING | read-write | Binary coded sensor selection: only selected sensors will be shown in the graphical presentation: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 Bit 2-7: unused |
| OCT wtWebGraphAnalog57662GraphicsSelectDisplayShowExtrem | 1.3.6.1.4.1.5040.1.2.29.3.1.6.2.2 | OCTET STRING | read-write | Binary coded sensor selection: only selected sensors will be shown with minima and maxima: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Sensor 1 Bit 1: Sensor 2 Bit 2-7: unused |
| wtWebGraphAnalog57662SensorColor2Table | 1.3.6.1.4.1.5040.1.2.29.3.1.6.2.3 | not-accessible | List of sensor colors for the praphical presentation. | |
| wtWebGraphAnalog57662SensorColor2Entry | 1.3.6.1.4.1.5040.1.2.29.3.1.6.2.3.1 | not-accessible | Numbers of the sensors. | |
| OCT wtWebGraphAnalog57662GraphicsSensorColor | 1.3.6.1.4.1.5040.1.2.29.3.1.6.2.3.1.1 | OCTET STRING | read-write | Color of the sensors at the praphical presention. |
| OCT wtWebGraphAnalog57662GraphicsSelectScale | 1.3.6.1.4.1.5040.1.2.29.3.1.6.2.3.1.2 | OCTET STRING | read-write | Assignes one of 4 scales to a sensor: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Use Scale 1 Bit 1 : Use Scale 2 Bit 2-7: unused |
| wtWebGraphAnalog57662GraphicsScale | 1.3.6.1.4.1.5040.1.2.29.3.1.6.3 | |||
| OCT wtWebGraphAnalog57662GraphicsScaleAutoScaleEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.6.3.1 | OCTET STRING | read-write | Select the Auto Scale Mode: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Scale 1 Auto scale enable Bit 1 : Scale 2 Auto scale enable Bit 2-7: unused |
| OCT wtWebGraphAnalog57662GraphicsScaleAutoFitEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.6.3.2 | OCTET STRING | read-write | Select the Auto Fit Mode:: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Scale 1 Auto fit enable Bit 1 : Scale 2 Auto fit enable Bit 2-7: unused |
| INT wtWebGraphAnalog57662GraphicsScale1Min | 1.3.6.1.4.1.5040.1.2.29.3.1.6.3.3 | INTEGER | read-only | Scale 1: Minimum. |
| INT wtWebGraphAnalog57662GraphicsScale2Min | 1.3.6.1.4.1.5040.1.2.29.3.1.6.3.4 | INTEGER | read-only | Scale 2: Minimum. |
| INT wtWebGraphAnalog57662GraphicsScale1Max | 1.3.6.1.4.1.5040.1.2.29.3.1.6.3.7 | INTEGER | read-only | Scale 1: Maximum. |
| INT wtWebGraphAnalog57662GraphicsScale2Max | 1.3.6.1.4.1.5040.1.2.29.3.1.6.3.8 | INTEGER | read-only | Scale 2: Maximum. |
| OCT wtWebGraphAnalog57662GraphicsScale1Unit | 1.3.6.1.4.1.5040.1.2.29.3.1.6.3.11 | OCTET STRING | read-only | Scale 1: Unit. |
| OCT wtWebGraphAnalog57662GraphicsScale2Unit | 1.3.6.1.4.1.5040.1.2.29.3.1.6.3.12 | OCTET STRING | read-only | Scale 2: Unit. |
| wtWebGraphAnalog57662Report | 1.3.6.1.4.1.5040.1.2.29.3.1.7 | |||
| INT wtWebGraphAnalog57662ReportCount | 1.3.6.1.4.1.5040.1.2.29.3.1.7.1 | INTEGER | read-only | Number of independent Reports. |
| wtWebGraphAnalog57662ReportIfTable | 1.3.6.1.4.1.5040.1.2.29.3.1.7.2 | not-accessible | List of Report indices. | |
| wtWebGraphAnalog57662ReportIfEntry | 1.3.6.1.4.1.5040.1.2.29.3.1.7.2.1 | not-accessible | Numbers of the Reports. | |
| INT wtWebGraphAnalog57662ReportNo | 1.3.6.1.4.1.5040.1.2.29.3.1.7.2.1.1 | INTEGER | read-only | Report number. |
| wtWebGraphAnalog57662ReportTable | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3 | not-accessible | List of settings depending on the Report number. | |
| wtWebGraphAnalog57662ReportEntry | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1 | not-accessible | Report parameters of the individual Reports. | |
| OCT wtWebGraphAnalog57662ReportEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.1 | OCTET STRING | read-write | Bin�r kodierte Triggerbedingungen: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Report enable Bit 1-7: unused |
| OCT wtWebGraphAnalog57662ReportTimerCron | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.2 | OCTET STRING | read-write | This entry defines a time window for alarm 1-8 and a activation time for the report. A time window is definied by start and stop time stamp, seperated by a space or tab. The activation time of the report is defined by a single start time stamp. Each time stamp contains 5 space or tab seperated text fields for time trigger definition. Each field must match with the actual time to trigger an action, weekday and day of month are interpreted separatley. 1: Minutes Range 0-59 2. Hours Range 0-23, 0 is midnight 3: Day of month Range 1-31 4: Month Range 1-12 5: Weekday Range 0-6, 0 is sunday Syntax for every field: - an asterix (*) enables every possible setting of a field - single numbers seperated by commas (i.e.: 2,14,22) - a partition within the allowed range (i.e.: 1-5) - step size within a partition of the allowed range (i.e.: 0-59/2 every second minute). |
| OCT wtWebGraphAnalog57662ReportMethodeEnable | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.3 | OCTET STRING | read-write | Binary coded alarm enable: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0: Mail Enable Bit 1: SNMP Trap enable Bit 2: TCP Client enable Bit 3: Syslog enable Bit 4: FTP Client enable |
| OCT wtWebGraphAnalog57662ReportEMailAddr | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.8 | OCTET STRING | read-write | E-Mail address for sending the alarm mail to. |
| OCT wtWebGraphAnalog57662ReportMailSubject | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.9 | OCTET STRING | read-write | Subject line for alarm mail. |
| OCT wtWebGraphAnalog57662ReportMailText | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.10 | OCTET STRING | read-write | Report mail text: provides the current temperature; n = 1..2. provides the current time. |
| OCT wtWebGraphAnalog57662ReportManagerIP | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.11 | OCTET STRING | read-write | Name or IP address of the SNMP Manager which accepts the trap. |
| OCT wtWebGraphAnalog57662ReportTrapText | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.12 | OCTET STRING | read-write | This text is sent in the trap body. |
| OCT wtWebGraphAnalog57662ReportMailOptions | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.13 | OCTET STRING | read-write | Binary coded options: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : Attach Thermo.csv Enable Bit 1 : CSV-Data_since_last_report Bit 2-7: unused |
| OCT wtWebGraphAnalog57662ReportTcpIpAddr | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.14 | OCTET STRING | read-write | Name or IP address of the TCP server which accepts the trap. |
| INT wtWebGraphAnalog57662ReportTcpPort | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.15 | INTEGER | read-write | Port number of the TCP server which accepts the trap. |
| OCT wtWebGraphAnalog57662ReportTcpText | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.16 | OCTET STRING | read-write | This text is sent in the TCP trap body. |
| OCT wtWebGraphAnalog57662ReportClearMailSubject | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.17 | OCTET STRING | read-write | Subject line for alarm clear mail. |
| OCT wtWebGraphAnalog57662ReportClearMailText | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.18 | OCTET STRING | read-write | Report clear mail text: provides the current temperature; n = 1..2. provides the current time. |
| OCT wtWebGraphAnalog57662ReportClearTrapText | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.19 | OCTET STRING | read-write | This text is sent in the trap body. |
| OCT wtWebGraphAnalog57662ReportClearTcpText | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.20 | OCTET STRING | read-write | This text is sent in the TCP trap body. |
| OCT wtWebGraphAnalog57662ReportSyslogIpAddr | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.24 | OCTET STRING | read-write | IP address of the syslog server to which the Webio device should send syslog messages. |
| INT wtWebGraphAnalog57662ReportSyslogPort | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.25 | INTEGER | read-write | Port number of the syslog server to which the Webio device should send syslog messages. |
| OCT wtWebGraphAnalog57662ReportSyslogText | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.26 | OCTET STRING | read-write | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body. |
| OCT wtWebGraphAnalog57662ReportSyslogClearText | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.27 | OCTET STRING | read-write | Every message starts with the priority key, a time stamp and the host ip address, according RFC3164. This text appears in the following syslog message body of a alarm clear message. |
| OCT wtWebGraphAnalog57662ReportFtpDataPort | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.28 | OCTET STRING | read-write | Local data port: 1..65535 or AUTO: the next free port will be assigned. |
| OCT wtWebGraphAnalog57662ReportFtpFileName | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.29 | OCTET STRING | read-write | Name of the file including path informations. |
| OCT wtWebGraphAnalog57662ReportFtpText | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.30 | OCTET STRING | read-write | Message text to store on the FTP server. |
| OCT wtWebGraphAnalog57662ReportFtpClearText | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.31 | OCTET STRING | read-write | Report clear message to store on the FTP server. |
| OCT wtWebGraphAnalog57662ReportFtpOption | 1.3.6.1.4.1.5040.1.2.29.3.1.7.3.1.32 | OCTET STRING | read-write | Binary coded options, select only one option at the same time: STORE = replace file APPEND = append message at the end of the file Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : STORE Bit 1 : APPEND Bit 2-7: unused |
| wtWebGraphAnalog57662Ports | 1.3.6.1.4.1.5040.1.2.29.3.2 | |||
| wtWebGraphAnalog57662PortTable | 1.3.6.1.4.1.5040.1.2.29.3.2.1 | not-accessible | List of settings depending on the sensor number. | |
| wtWebGraphAnalog57662PortEntry | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1 | not-accessible | Sensor parameters for the individual sensors. | |
| OCT wtWebGraphAnalog57662PortName | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.1 | OCTET STRING | read-write | Name of the sensor. |
| OCT wtWebGraphAnalog57662PortText | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.2 | OCTET STRING | read-write | Description of the sensor. |
| OCT wtWebGraphAnalog57662PortOffset1 | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.3 | OCTET STRING | read-write | Offset calibration: Offset in degrees with maximum 3 decimal places at set point 1. |
| OCT wtWebGraphAnalog57662SetPoint1 | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.4 | OCTET STRING | read-write | Offset calibration: Reference set point 1 in degrees with maximum 3 decimal places. |
| OCT wtWebGraphAnalog57662PortOffset2 | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.5 | OCTET STRING | read-write | Offset calibration: Offset in degrees with maximum 3 decimal places at set point 2. |
| OCT wtWebGraphAnalog57662SetPoint2 | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.6 | OCTET STRING | read-write | Offset calibration: Reference set point 2 in degrees with maximum 3 decimal places. |
| OCT wtWebGraphAnalog57662PortComment | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.7 | OCTET STRING | read-write | Offset calibration: informations of date, name of operator, reference devices. |
| OCT wtWebGraphAnalog57662PortSensorSelect | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.8 | OCTET STRING | read-write | Binary coded options for sensor 1: Octet 1: unused Octet 2: unused Octet 3: unused Octet 4: Bit 0 : 0-20mA (default) Bit 1 : 4-20mA Bit 2 : Disconnect Bit 3-7: unused |
| OCT wtWebGraphAnalog57662PortUnit | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.9 | OCTET STRING | read-write | User scale: displayed unit. |
| OCT wtWebGraphAnalog57662PortScale0 | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.10 | OCTET STRING | read-write | User scale: displayed value in 1/1000 at 0% full scale range. Range: -999999.999 to 999999.999 |
| OCT wtWebGraphAnalog57662PortScale100 | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.11 | OCTET STRING | read-write | User scale: displayed value in 1/1000 at 100% full scale range. Range: -999999.999 to 999999.999 |
| OCT wtWebGraphAnalog57662PortOutputMode | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.12 | OCTET STRING | read-write | This binary coded output mode defines the individual operation mode for any output. More than one mode must not be selected. If an output mode is selected, Bit 2 in wtWebGraphAnalog57662PortInputMode will be set automatically. The OCTETS are interpreted bit-by-bit, Bit 0 corresponds to the LSB. OCTET 1: unused OCTET 2: unused OCTET 3: unused OCTET 4: Bit 6-7: unused Bit 5 : Output OFF Bit 4 : Binary 2 Bit 3 : Binary 1 Bit 2 : SNMP Bit 1 : UDP ASCII Bit 0 : HTTP |
| OCT wtWebGraphAnalog57662PortInputMode | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.13 | OCTET STRING | read-write | This binary coded input mode defines the individual operation mode for any input. More than one mode must not be selected. If an input mode is selected, Bit 5 in wtWebGraphAnalog57662PortOutputMode will be set automatically. The OCTETS are interpreted bit-by-bit,Bit 0 corresponds to the LSB. OCTET 1: ungenutzt OCTET 2: ungenutzt OCTET 3: ungenutzt OCTET 4: Bit 3-7: unused Bit 2 : I-Output Bit 1 : I-Input, active Bit 0 : I-Input, passive |
| OCT wtWebGraphAnalog57662PortCompensationValue | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.14 | OCTET STRING | read-write | This entry is used to optimize the step response with capcitive loads. |
| OCT wtWebGraphAnalog57662PortCompensationMode | 1.3.6.1.4.1.5040.1.2.29.3.2.1.1.15 | OCTET STRING | read-write | This binary coded compensation mode defines the individual operation mode for any output. If Auto adaptive is selected, the optimal value of wtWebGraphAnalog57662PortCompensationValue will be determinate continuously. Set Bit 1 to start with the last saved value of wtWebGraphAnalog57662PortCompensationValue in this Mode. If Bit 0 is cleared and Auto Mode is off wtWebGraphAnalog57662PortCompensationValue will allways be used, regardless of the state of Bit 1. The OCTETS are interpreted bit-by-bit,Bit 0 corresponds to the LSB. OCTET 1: ungenutzt OCTET 2: ungenutzt OCTET 3: ungenutzt OCTET 4: Bit 2-7: unused Bit 1 : Use saved value at power on Bit 0 : Auto adaptive enable |
| wtWebGraphAnalog57662Manufact | 1.3.6.1.4.1.5040.1.2.29.3.3 | |||
| OCT wtWebGraphAnalog57662MfName | 1.3.6.1.4.1.5040.1.2.29.3.3.1 | OCTET STRING | read-write | Manufacturer company name |
| OCT wtWebGraphAnalog57662MfAddr | 1.3.6.1.4.1.5040.1.2.29.3.3.2 | OCTET STRING | read-write | Manufacturer address. |
| OCT wtWebGraphAnalog57662MfHotline | 1.3.6.1.4.1.5040.1.2.29.3.3.3 | OCTET STRING | read-write | Manufacturer hotline. |
| OCT wtWebGraphAnalog57662MfInternet | 1.3.6.1.4.1.5040.1.2.29.3.3.4 | OCTET STRING | read-write | Manufacturer Internet address. |
| OCT wtWebGraphAnalog57662MfDeviceTyp | 1.3.6.1.4.1.5040.1.2.29.3.3.5 | OCTET STRING | read-write | Manufacturer device name (model number). |
| OCT wtWebGraphAnalog57662MfOrderNo | 1.3.6.1.4.1.5040.1.2.29.3.3.6 | OCTET STRING | read-write | Manufacturer part number. |
| wtWebGraphAnalog57662Diag | 1.3.6.1.4.1.5040.1.2.29.4 | |||
| INT wtWebGraphAnalog57662DiagErrorCount | 1.3.6.1.4.1.5040.1.2.29.4.1 | INTEGER | read-only | Number of entries in the error memory. |
| OCT wtWebGraphAnalog57662DiagBinaryError | 1.3.6.1.4.1.5040.1.2.29.4.2 | OCTET STRING | read-only | Error causes coded bit-by-bit. |
| INT wtWebGraphAnalog57662DiagErrorIndex | 1.3.6.1.4.1.5040.1.2.29.4.3 | INTEGER | read-write | The value of this variable is used as an index to read an error massege from wtWebGraphAnalog57662DiagErrorMessage. Errors are numbered from 1 to wtWebGraphAnalog57662DiagErrorCount. Writing a valid value into this variable, making the appropriate message readable from wtWebGraphAnalog57662DiagErrorMessage. |
| OCT wtWebGraphAnalog57662DiagErrorMessage | 1.3.6.1.4.1.5040.1.2.29.4.4 | OCTET STRING | read-only | Using wtWebGraphAnalog57662DiagErrorIndex as an index, the appropriate message is available. |
| INT wtWebGraphAnalog57662DiagErrorClear | 1.3.6.1.4.1.5040.1.2.29.4.5 | INTEGER | write-only | Writing 1 into this variable clears all diagnosis messages. |
RFC description
Management information base for WebGraph AnalogIO 57662 analog input/output monitoring modules. Provides SNMP objects for managing sensor inputs and control outputs in environmental monitoring and data acquisition systems.
Start monitoring WebGraph model 57662 analog/binary I/O monitoring unit (per-channel sensor reading/binary I/O status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.