RAPID-CITY-VSP (page 1 of 2)

OID symbolic	OID numeric	Type	Access	Description
internet	1.3.6.1
rapidCity	1.3.6.1.4.1.2272			Enterprise MIB for the Accelar product family.
rcMgmt	1.3.6.1.4.1.2272.1
rcSystem	1.3.6.1.4.1.2272.1.1
IP rcSysIpAddr	1.3.6.1.4.1.2272.1.1.1	IpAddress	read-only	This entity's IP address.
IP rcSysNetMask	1.3.6.1.4.1.2272.1.1.2	IpAddress	read-only	This entity's subnet mask.
IP rcSysBroadcast	1.3.6.1.4.1.2272.1.1.3	IpAddress	read-only	This entity's broadcast address.
STR rcSysVersion	1.3.6.1.4.1.2272.1.1.7	DisplayString	read-only	Software version running on device
INT rcSysResult	1.3.6.1.4.1.2272.1.1.9	INTEGER	read-only	Result from the last system action.
TIK rcSysLastChange	1.3.6.1.4.1.2272.1.1.10	TimeTicks	read-only	Last management initiated configuration change since sysUpTime.
TIK rcSysLastVlanChange	1.3.6.1.4.1.2272.1.1.11	TimeTicks	read-only	Last management initiated VLAN configuration change since sysUpTime.
TIK rcSysLastStatisticsReset	1.3.6.1.4.1.2272.1.1.12	TimeTicks	read-only	Last management initiated statistics reset since sysUpTime.
INT rcSysBufferUtil	1.3.6.1.4.1.2272.1.1.13	INTEGER	read-only	Buffer utilization as a percentage of the total amount of buffer space in the system. A high value indicates congestion.
INT rcSysBufferUtilPeak	1.3.6.1.4.1.2272.1.1.14	INTEGER	read-only	The largest buffer utilization since sysUpTime
TIK rcSysBufferUtilPeakTime	1.3.6.1.4.1.2272.1.1.15	TimeTicks	read-only	Timestamp for rcSysPeakBandwidth
G32 rcSysNVRamSize	1.3.6.1.4.1.2272.1.1.16	Gauge32	read-only	Total Non-volatile RAM in Kbytes
G32 rcSysNVRamUsed	1.3.6.1.4.1.2272.1.1.17	Gauge32	read-only	Non-volatile RAM in use in Kbytes
TIK rcSysLastSaveToNVRam	1.3.6.1.4.1.2272.1.1.18	TimeTicks	read-only	SysUpTime of the last time when NVRAM was written to. This could be a save of the system configuration or via a file transfer of a configuration file.
TIK rcSysLastSaveToStandbyNVRam	1.3.6.1.4.1.2272.1.1.19	TimeTicks	read-only	SysUpTime of the last time when the standby NVRAM (on the back-up CPU board) was written to.
G32 rcSysCpuUtil	1.3.6.1.4.1.2272.1.1.20	Gauge32	read-only	Percentage of CPU utilization. This object is not supported on VSP. VSP uses rcKhiSlotCpuCurrentUtil
INT rcSysRmonMemSize	1.3.6.1.4.1.2272.1.1.22	INTEGER	read-write	Amount of RAM in bytes to allocate for RMON to use when rcSysRmonEnable is TRUE.
T/F rcSysRmonEnable	1.3.6.1.4.1.2272.1.1.23	TruthValue	read-write	Control whether the RMON feature should be enabled. To enable the RMON feature, set this variable to true. The RMON agent in the device will get started immediately if the amount of memory specified by rcSysRmonMemSize is currently available in the device. To disable the RMON feature, set this variable to false, save the new setting to NVRAM, and reboot the device. After the device is rebooted the RMON agent will not be operational.
INT rcSysRmonTrapOption	1.3.6.1.4.1.2272.1.1.25	INTEGER	read-write	Used to indicate whether RMON traps should be sent to only the owner of the RMON alarm (i.e., the manager that created the alarm entry) or all trap recipients in the system trap receiver table.
T/F rcSysSupportRouting	1.3.6.1.4.1.2272.1.1.26	TruthValue	read-only	Used to indicate whether routing is supported in this product.
T/F rcSysSupportWebServer	1.3.6.1.4.1.2272.1.1.27	TruthValue	read-only	Used to indicate whether WebServer is supported in this product.
TIK rcSysLastIpAddrChange	1.3.6.1.4.1.2272.1.1.28	TimeTicks	read-only	Last management initiated IP address change since sysUpTime. Any addition or deletion of an IP address to a single routable port or a VLAN is time-stamped by this variable.
T/F rcSysAccessPolicyEnable	1.3.6.1.4.1.2272.1.1.31	TruthValue	read-write	Used to configure the system access policy feature. if 'true', the rcSysAccessPolicyTable is examined to determine which packets should be allowed or denied access to this device.
STR rcSysDefaultRuntimeConfigFileName	1.3.6.1.4.1.2272.1.1.32	DisplayString	read-only	default config.
STR rcSysDefaultBootConfigFileName	1.3.6.1.4.1.2272.1.1.33	DisplayString	read-only	default boot config.
STR rcSysConfigFileName	1.3.6.1.4.1.2272.1.1.34	DisplayString	read-write	File name used in conjunction with rcSysAction. If rcSysAction is set to 'saveRuntimeConfig' or 'saveRuntimeConfigToSlave' then this file name will be used instead of the file name specified in rcSysDefaultRuntimeConfigFileName. If rcSysAction is set to 'saveBootConfig' or 'saveBootConfigToSlave' then this file name will be used insteaad of the file name specified in rcSysDefaultBootConfigFileName. If the file name is blank (i.e., nothing is entered) then the default file name will be used.
TIK rcSysLastRunTimeConfigSave	1.3.6.1.4.1.2272.1.1.35	TimeTicks	read-only	SysUpTime of the last time when the run time configuration was written to.
TIK rcSysLastRunTimeConfigSaveToSlave	1.3.6.1.4.1.2272.1.1.36	TimeTicks	read-only	SysUpTime of the last time when the run time configuration was written to slave NVRAM.
TIK rcSysLastBootConfigSave	1.3.6.1.4.1.2272.1.1.37	TimeTicks	read-only	SysUpTime of the last time when the boot configuration was written to.
TIK rcSysLastBootConfigSaveOnSlave	1.3.6.1.4.1.2272.1.1.38	TimeTicks	read-only	SysUpTime of the last time when the boot configuration was written on the slave NVRAM.
INT rcSysRmonUtilizationMethod	1.3.6.1.4.1.2272.1.1.39	INTEGER	read-write	Used to control whether RMON should use a half-duplex or full-duplex formula to calculate port utilization. When set to 'halfDuplex', RMON will use InOctets and the port's speed to calculate port utilization (this is the standard RMON rfc1271 convention). When set to 'fullDuplex', RMON will use InOctets and OutOctets and 2X the port's speed to calculate port utilization. Furthermore, if this variable is set to 'fullDuplex', but the port is operating in a half-duplex mode, the calculation defaults back to the rfc1271 convention.
G32 rcSysOtherBufferUtil	1.3.6.1.4.1.2272.1.1.41	Gauge32	read-only	bw currently consumed
G32 rcSysOtherBufferUtilPeak	1.3.6.1.4.1.2272.1.1.42	Gauge32	read-only	peak bw since reset
TIK rcSysOtherBufferUtilPeakTime	1.3.6.1.4.1.2272.1.1.43	TimeTicks	read-only	timestamp for rcSysPeakBw
G32 rcSysOtherCpuUtil	1.3.6.1.4.1.2272.1.1.44	Gauge32	read-only	% cpu utilization
I32 rcSysDramSize	1.3.6.1.4.1.2272.1.1.46	Integer32	read-only	Dram size in mega-bytes
G32 rcSysDramUsed	1.3.6.1.4.1.2272.1.1.47	Gauge32	read-only	Dram used in percentage
I32 rcSysDramFree	1.3.6.1.4.1.2272.1.1.48	Integer32	read-only	Dram free size in kilo-bytes
I32 rcSysDramMaxBlockFree	1.3.6.1.4.1.2272.1.1.49	Integer32	read-only	Dram max block free size in kilo-bytes
IP rcSysVirtualIpAddr	1.3.6.1.4.1.2272.1.1.51	IpAddress	read-write	Virtual IP is an IP address that owned and advertised only by the master CPU. So whichever CPU is master registers this IP address. Unlike the management IP address, this address goes in the switch config file and not the boot config
IP rcSysVirtualNetMask	1.3.6.1.4.1.2272.1.1.52	IpAddress	read-write	Net mask of the management virtual Ip address
I32 rcSysReadWriteLevel	1.3.6.1.4.1.2272.1.1.53	Integer32	read-write	The status of the read/write level
INT rcSysMTUSize	1.3.6.1.4.1.2272.1.1.55	INTEGER	read-write	This is the maximum transmission size of frames that all the ports on the chassis support.
T/F rcSysForceTrapSender	1.3.6.1.4.1.2272.1.1.57	TruthValue	read-write	This is a flag that if user wants to configured CLIP (Circuit Less IP) as trap originator.
T/F rcSysMrouteStrLimit	1.3.6.1.4.1.2272.1.1.58	TruthValue	read-write	enable or disable mroute stream limit in system.
rcSysAccessPolicyTable	1.3.6.1.4.1.2272.1.1.61		not-accessible	Management access policy table. This table is used to permit or deny access to this device via the specified source Id.
rcSysAccessPolicyEntry	1.3.6.1.4.1.2272.1.1.61.1		not-accessible	An access policy table entry.
INT rcSysAccessPolicyId	1.3.6.1.4.1.2272.1.1.61.1.1	INTEGER	read-only	Policy Id.
STR rcSysAccessPolicyName	1.3.6.1.4.1.2272.1.1.61.1.2	DisplayString	read-write	Name of this policy.
T/F rcSysAccessPolicyPolicyEnable	1.3.6.1.4.1.2272.1.1.61.1.3	TruthValue	read-write	Indicate whether this policy is currently active.
INT rcSysAccessPolicyMode	1.3.6.1.4.1.2272.1.1.61.1.4	INTEGER	read-write	Used to indicate whether a packet having a source IP address that matches this entry should be permitted to enter the device or denied access.
INT rcSysAccessPolicyService	1.3.6.1.4.1.2272.1.1.61.1.5	INTEGER	read-write	Is represented as bitset to indicate which protocol this entry should be applied to. Value is one of multiple(logical 'OR') of the following values: telnet(1), snmp(2), tftp(4), ftp(8), http(16), rlogin(32), ssh(64), snmp-v3(128) telnet(1): enables telnet service snmp(2): enables snmp service tftp(4): enables tftp service ftp(8): enables ftp service http(16): enables http service rlogin(32): enables rlogin service ssh(64): enables ssh service snmp-v3(128): enables snmp service for v3 groups Value 0 means no service enabled.
INT rcSysAccessPolicyPrecedence	1.3.6.1.4.1.2272.1.1.61.1.6	INTEGER	read-write	Used to indicate the precedence of this policy. The Lower the number the higher the precedence.
STR rcSysAccessPolicyTrustedHostUserName	1.3.6.1.4.1.2272.1.1.61.1.10	DisplayString	read-write	User name on the trusted host performing a rlogin into the device.
INT rcSysAccessPolicyAccessLevel	1.3.6.1.4.1.2272.1.1.61.1.11	INTEGER	read-write	Access level of trusted host.
T/F rcSysAccessPolicyLog	1.3.6.1.4.1.2272.1.1.61.1.12	TruthValue	read-write	Used to indicate whether logging should be performed if this policy was applied.
C32 rcSysAccessPolicyUsage	1.3.6.1.4.1.2272.1.1.61.1.13	Counter32	read-only	Usage Counter
ROW rcSysAccessPolicyRowStatus	1.3.6.1.4.1.2272.1.1.61.1.14	RowStatus	read-write	Used to create/delete an entry
T/F rcSysAccessPolicyAccessStrict	1.3.6.1.4.1.2272.1.1.61.1.15	TruthValue	read-write	Used to restrict the access level specified in the system access policy table to exactly the same access level as specified by user. If TRUE then only the access level in the policy table is allowed access. If FALSE, then the default behavior is to assume the access level specified in policy table as the floor.
INT rcSysAccessPolicyNetInetAddrType	1.3.6.1.4.1.2272.1.1.61.1.16	INTEGER	read-write	Source network Inet Address Type.
IP rcSysAccessPolicyNetInetAddress	1.3.6.1.4.1.2272.1.1.61.1.17	InetAddress	read-write	Source network Inet Address (prefix/network).
ADR rcSysAccessPolicyNetInetAddrPrefixLen	1.3.6.1.4.1.2272.1.1.61.1.18	InetAddressPrefixLength	read-write	Source network Inet Address Prefix-Length/Mask.
IP rcSysAccessPolicyTrustedHostInetAddress	1.3.6.1.4.1.2272.1.1.61.1.19	InetAddress	read-write	Trusted Inet address of host performing a rlogin into the device.
rcSysTrapSenderTable	1.3.6.1.4.1.2272.1.1.62		not-accessible	The trap sender table (0 to 25 entries). This table lists the addresses of Network Management Stations and the Source Address that should receive trap messages from this entity when an exception condition occurs.
rcSysTrapSenderEntry	1.3.6.1.4.1.2272.1.1.62.1		not-accessible	A trap sender table entry.
IP rcSysTrapSenderRecvAddress	1.3.6.1.4.1.2272.1.1.62.1.1	IpAddress	read-only	IP address for trap receiver.
IP rcSysTrapSenderSrcAddress	1.3.6.1.4.1.2272.1.1.62.1.2	IpAddress	read-write	IP address for trap sender.
rcSysDnsServerListTable	1.3.6.1.4.1.2272.1.1.64		not-accessible	DNS serever list table used to store the details of the DNS server configured.
rcSysDnsServerListEntry	1.3.6.1.4.1.2272.1.1.64.1		not-accessible	table entry.
INT rcSysDnsServerListType	1.3.6.1.4.1.2272.1.1.64.1.1	INTEGER	read-only	Type of the DNS server
INT rcSysDnsServerListStatus	1.3.6.1.4.1.2272.1.1.64.1.3	INTEGER	read-only	Status of DNS server
C32 rcSysDnsServerListRequestCount	1.3.6.1.4.1.2272.1.1.64.1.4	Counter32	read-only	Number of request send to this server
C32 rcSysDnsServerListSuccessCount	1.3.6.1.4.1.2272.1.1.64.1.5	Counter32	read-only	Number of request send to this server which are successful
ROW rcSysDnsServerListRowStatus	1.3.6.1.4.1.2272.1.1.64.1.6	RowStatus	read-write	Used to create/delete DNS server entries in rcSysDnsServerListTable.
IPt rcSysDnsServerListAddressType	1.3.6.1.4.1.2272.1.1.64.1.7	InetAddressType	read-write	The address type of DNS Server.
IP rcSysDnsServerListAddress	1.3.6.1.4.1.2272.1.1.64.1.8	InetAddress	read-write	The address of the DNS Server
rcSysDnsHostTable	1.3.6.1.4.1.2272.1.1.65		not-accessible	DNS Host table.
rcSysDnsHostEntry	1.3.6.1.4.1.2272.1.1.65.1		not-accessible	table entry.
OCT rcSysDnsHostData	1.3.6.1.4.1.2272.1.1.65.1.1	OCTET STRING	read-only	Host Name or Host IP Address.
OCT rcSysDnsHostName	1.3.6.1.4.1.2272.1.1.65.1.2	OCTET STRING	read-only	Host Name.
OCT rcSysDnsHostSource	1.3.6.1.4.1.2272.1.1.65.1.4	OCTET STRING	read-only	DNS Server IP or /etc/host file.
IPt rcSysDnsHostAddressType	1.3.6.1.4.1.2272.1.1.65.1.5	InetAddressType	read-only	Address Type of the Host.
IP rcSysDnsHostAddress	1.3.6.1.4.1.2272.1.1.65.1.6	InetAddress	read-only	Address of the Host.
INT rcSysMsgLogFrequency	1.3.6.1.4.1.2272.1.1.66	INTEGER	read-only	Used to specify the maximum frequency/count of the occurence of the Log Message.
STR rcSysMsgLogText	1.3.6.1.4.1.2272.1.1.67	DisplayString	read-only	A textual string containing the first four characters of the Log Message.
T/F rcSysForceIpHdrSender	1.3.6.1.4.1.2272.1.1.68	TruthValue	read-write	Flag to decide if IP header source address will be matched with SNMP header sender networks.
STR rcSysDnsDomainName	1.3.6.1.4.1.2272.1.1.70	DisplayString	read-write	Default domain used for querying the DNS Server.
IP rcSysDnsServerListIpAddr	1.3.6.1.4.1.2272.1.1.71	IpAddress	read-only	DNS server's IP address
INT rcSysDnsRequestType	1.3.6.1.4.1.2272.1.1.72	INTEGER	read-only	DNS Type: Whether it was Dns Request or a Response
INT rcSysSpanningTreeOperMode	1.3.6.1.4.1.2272.1.1.73	INTEGER	read-only	This object indicates the current spanning-tree mode of the system. The meaning of specific values is: nortelStpg(1) .. The older proprietary mode which supports multiple spanning tree groups. pvst(2) ..Emulation of C***O spanning tree mode rstp(3) ..IEEE 802.1w mode mstp(4) ..IEEE 802.1s mode .
INT rcSysSpanningTreeAdminMode	1.3.6.1.4.1.2272.1.1.74	INTEGER	read-write	This object indicates the desired spanning-tree mode of the system. The meaning of specific values is: nortelStpg(1) .. The older proprietary mode which supports multiple spanning tree groups. pvst(2) ..Emulation of C***O spanning tree mode rstp(3) ..IEEE 802.1w mode mstp(4) ..IEEE 802.1s mode . Note that depending on the current value of rcSysSpanningTreeOperMode and the value to which this object is set, the operational mode may be immediately changed, or the change may not take effect until the next system reboot.
INT rcSysAutoRecoverDelay	1.3.6.1.4.1.2272.1.1.75	INTEGER	read-write	Time interval in seconds after which auto-recovery runs on ports to clear action taken by cp-limit, link flap or loop detect
INT rcSysMacFlapLimitTime	1.3.6.1.4.1.2272.1.1.76	INTEGER	read-write	Time limit in milliseconds for MAC flapping for loop-detect feature
I32 rcSysMacFlapLimitCount	1.3.6.1.4.1.2272.1.1.77	Integer32	read-only	Number of times mac flapping can happen for loop-detect feature
T/F rcSysExtCplimitEnable	1.3.6.1.4.1.2272.1.1.78	TruthValue	read-write	enable or disable extended CP-LIMIT in system.
INT rcSysExtCplimitMinCongTime	1.3.6.1.4.1.2272.1.1.79	INTEGER	read-write	Minimum time for which System octapid should be congested to trigger congestion algorithm for extended CP-LIMIT in mSecs
INT rcSysExtCplimitMaxPorts	1.3.6.1.4.1.2272.1.1.80	INTEGER	read-write	Maximum number of ports which need to be monitored for congestion in Extended CP-LIMIT
INT rcSysExtCplimitPortCongTime	1.3.6.1.4.1.2272.1.1.81	INTEGER	read-write	Minimum time for which ingress traffic utilization rate of a monitored port should stay more than the allowed limits in order to disable the port for extended CP-LIMIT in Secs
INT rcSysExtCplimitTrapLevel	1.3.6.1.4.1.2272.1.1.82	INTEGER	read-write	Indicates the trap level for extended CP-LIMIT
T/F rcSysExtCplimitSysOctapidCongested	1.3.6.1.4.1.2272.1.1.83	TruthValue	read-only	Indicates whether system octapid congestion detected for extended cp-limit
T/F rcSysExtCplimitPortsMonitored	1.3.6.1.4.1.2272.1.1.84	TruthValue	read-only	Indicates whether ports has been shutdown due to extended cp-limit
T/F rcSysExtCplimitPortsShutDown	1.3.6.1.4.1.2272.1.1.85	TruthValue	read-only	Indicates whether ports has been shutdown due to extended Cp-limit
INT rcSysActionL1	1.3.6.1.4.1.2272.1.1.86	INTEGER	read-write	Initiate a system action for layer1 user
INT rcSysActionL2	1.3.6.1.4.1.2272.1.1.87	INTEGER	read-write	Initiate a system action for layer2 user
INT rcSysActionL3	1.3.6.1.4.1.2272.1.1.88	INTEGER	read-write	Initiate a system action for layer3 user
INT rcSysActionRwa	1.3.6.1.4.1.2272.1.1.89	INTEGER	read-write	Initiate a system action.
I32 rcSysPowerUsage	1.3.6.1.4.1.2272.1.1.90	Integer32	read-only	The current power usage for the whole chassis.
I32 rcSysPowerAvailable	1.3.6.1.4.1.2272.1.1.91	Integer32	read-only	The current power available for the whole chassis.
rcSysFrcMsgControlTable	1.3.6.1.4.1.2272.1.1.94		not-accessible	Management Force-msg Control table. This table is used to specify the pattern for Force-msg Control
rcSysFrcMsgControlEntry	1.3.6.1.4.1.2272.1.1.94.1		not-accessible	A Force-msg Control table entry.
I32 rcSysFrcMsgControlPatternId	1.3.6.1.4.1.2272.1.1.94.1.1	Integer32	not-accessible	Pattern Id.
STR rcSysFrcMsgControlPattern	1.3.6.1.4.1.2272.1.1.94.1.2	DisplayString	read-write	Pattern for filtering the force-msg for msg control
ROW rcSysFrcMsgControlRowStatus	1.3.6.1.4.1.2272.1.1.94.1.3	RowStatus	read-write	Used to create/delete an entry
rcSysAccPolSnmpGrpTable	1.3.6.1.4.1.2272.1.1.95		not-accessible	SNMP group list for access policy
rcSysAccPolSnmpGrpEntry	1.3.6.1.4.1.2272.1.1.95.1		not-accessible	The table entry which covers the groups under snmp service.
STR rcSysAccPolSnmpGrpName	1.3.6.1.4.1.2272.1.1.95.1.1	SnmpAdminString	not-accessible	The snmp-v3 group name
SNM rcSysAccPolSnmpGrpModel	1.3.6.1.4.1.2272.1.1.95.1.2	SnmpSecurityModel	not-accessible	The snmp model
ROW rcSysAccPolSnmpGrpRowStatus	1.3.6.1.4.1.2272.1.1.95.1.3	RowStatus	read-write	Row status
ADR rcSysVirtualIpv6Addr	1.3.6.1.4.1.2272.1.1.96	Ipv6Address	read-write	Virtual IP is an IP address that owned and advertised only by the master CPU. So whichever CPU is master registers this IP address.
INT rcSysVirtualIpv6PrefixLength	1.3.6.1.4.1.2272.1.1.97	INTEGER	read-write	The length of the virtual ipv6 addr prefix (in bits).
U32 rcSysLicenseTrialDaysLeft	1.3.6.1.4.1.2272.1.1.100	Unsigned32	read-only	This indicates days left before License Trial Period will expire.
I32 rcSysTotalPower	1.3.6.1.4.1.2272.1.1.116	Integer32	read-only	The total power for the whole chassis.
I32 rcSysRedundantPower	1.3.6.1.4.1.2272.1.1.117	Integer32	read-only	Used to indicate the redundant power on the chassis. The redundant power is per power supply unit
T/F rcSysAuthSuccessTrapEnable	1.3.6.1.4.1.2272.1.1.118	TruthValue	read-write	Used to enable/disable the trap send for authenticaion success trap rcnAuthenticationSuccess. It only allow to be set when snmpEnableAuthenTraps is enabled. I will be set to disable when snmpEnableAuthenTraps is disabled
T/F rcSysUdpSrcByVirtualIpEnable	1.3.6.1.4.1.2272.1.1.119	TruthValue	read-write	Used to enable/disable virtual ip as udp source.
rcTftp	1.3.6.1.4.1.2272.1.2
IP rcTftpHost	1.3.6.1.4.1.2272.1.2.1	IpAddress	read-write	Name of source/destination host for the TFTP transfer.
STR rcTftpFile	1.3.6.1.4.1.2272.1.2.2	DisplayString	read-write	Name of file for the TFTP transfer.
INT rcTftpAction	1.3.6.1.4.1.2272.1.2.3	INTEGER	read-write	The action for the TFTP transfer.
INT rcTftpResult	1.3.6.1.4.1.2272.1.2.4	INTEGER	read-only	Contains result of the last Tftp action request.
rcVlan	1.3.6.1.4.1.2272.1.3
INT rcVlanNumVlans	1.3.6.1.4.1.2272.1.3.1	INTEGER	read-only	The number of VLANs currently defined in the switch.
rcVlanTable	1.3.6.1.4.1.2272.1.3.2		not-accessible	A list of Virtual LAN entries. The number of entries is given by rcVlanNumVlans.
rcVlanEntry	1.3.6.1.4.1.2272.1.3.2.1		not-accessible	Entry containing configuration information for a particular Virtual LAN. The relationship between the various port sets in a VLAN Entry are : o The set of ports defined by PortMembers must be a subset of the set of ports in the underlying STG of the VLAN. o The bitwise AND of PortMembers and NotAllowToJoin must be the empty set. o The bitwise OR of PortMembers and NotAllowToJoin must be the set of ports in the underlying STG of the VLAN. o The set of ports defined by StaticMembers must be a subset of the set of ports defined by PortMembers. o The bitwise XOR of PortMembers and StaticMembers defines the set of dynamic (potential) members of the VLAN. o The set of ports defined by ActiveMembers must be a subset of the set of ports defined by PortMembers.
RCV rcVlanId	1.3.6.1.4.1.2272.1.3.2.1.1	RcVlanIdOrNone	read-only	A value that uniquely identifies the Virtual LAN associated with this entry. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag.
STR rcVlanName	1.3.6.1.4.1.2272.1.3.2.1.2	DisplayString	read-write	An administratively-assigned name for this VLAN.
INT rcVlanColor	1.3.6.1.4.1.2272.1.3.2.1.3	INTEGER	read-write	An administratively-assigned color code for this VLAN. The value of this object is used by the VLAN Manager GUI tool to select a color when it draws this VLAN on the screen.
NUM rcVlanIfIndex	1.3.6.1.4.1.2272.1.3.2.1.6	InterfaceIndex	read-only	When rcVlanRoutingEnable is set to true(1), this value indicates the 'logical' ifIndex assigned to this VLAN. Otherwise, this value is meaningless and should be set to zero.
INT rcVlanAction	1.3.6.1.4.1.2272.1.3.2.1.7	INTEGER	read-write	VLAN related actions.
INT rcVlanResult	1.3.6.1.4.1.2272.1.3.2.1.8	INTEGER	read-only	The result from the last VLAN action.
INT rcVlanStgId	1.3.6.1.4.1.2272.1.3.2.1.9	INTEGER	read-write	Indicates the Spanning Tree Group (STG) used by this VLAN to determine the state of its ports. If this VLAN is not associated with any STG, this value should be set to zero.
INT rcVlanType	1.3.6.1.4.1.2272.1.3.2.1.10	INTEGER	read-write	The type of VLAN, distinguished according to the policy used to define its port membership. VSP9000 does not support bySvlan(6) and ByIds(7).
POR rcVlanPortMembers	1.3.6.1.4.1.2272.1.3.2.1.11	PortSet	read-write	The set of ports that are members (static or dynamic) of this VLAN.
POR rcVlanActiveMembers	1.3.6.1.4.1.2272.1.3.2.1.12	PortSet	read-only	The set of ports that are currently active in this VLAN. Active ports include all static ports and any dynamic ports where the VLAN policy was met.
POR rcVlanStaticMembers	1.3.6.1.4.1.2272.1.3.2.1.13	PortSet	read-write	The set of ports that are static members of this VLAN. A static member of a VLAN is always active and is never aged out.
POR rcVlanNotAllowToJoin	1.3.6.1.4.1.2272.1.3.2.1.14	PortSet	read-write	The set of ports that are not allowed to become members of this VLAN.
INT rcVlanProtocolId	1.3.6.1.4.1.2272.1.3.2.1.15	INTEGER	read-write	The protocol identifier of this VLAN. This value is meaningful only if rcVlanType is equal to byProtocolId(3). For other VLAN types it should have the value none(0).
IP rcVlanSubnetAddr	1.3.6.1.4.1.2272.1.3.2.1.16	IpAddress	read-write	The IP subnet address of this VLAN. This value is meaningful only if rcVlanType is equal to byIpSubnet(2). For other VLAN types it should have the value 0.0.0.0.
IP rcVlanSubnetMask	1.3.6.1.4.1.2272.1.3.2.1.17	IpAddress	read-write	The IP subnet mask of this VLAN. This value is meaningful only if rcVlanType is equal to byIpSubnet(2). For other VLAN types it should have the value 0.0.0.0.
INT rcVlanAgingTime	1.3.6.1.4.1.2272.1.3.2.1.18	INTEGER	read-write	The timeout period (in seconds) used for aging out dynamic members of this VLAN. This field is only relevant for policy-based VLANs.
MAC rcVlanMacAddress	1.3.6.1.4.1.2272.1.3.2.1.19	MacAddress	read-only	The MAC address assigned to the virtual router interface of this VLAN. This field is meaningful only if rcVlanRoutingEnable is equal to true(1).
ROW rcVlanRowStatus	1.3.6.1.4.1.2272.1.3.2.1.20	RowStatus	read-write	Used to create/delete entries in the rcVlanTable.
I32 rcVlanUserDefinedPid	1.3.6.1.4.1.2272.1.3.2.1.26	Integer32	read-write	When rcVlanProtocolId is set to usrDefined(15) in a protocol-based VLAN, this field represents the 16-bit user defined protocol identifier.
I32 rcVlanProtocolIds	1.3.6.1.4.1.2272.1.3.2.1.28	Integer32	read-write	Bitfield of protocol ids.
INT rcVlanTosValue	1.3.6.1.4.1.2272.1.3.2.1.34	INTEGER	read-write	Tos value.
INT rcVlanEncap	1.3.6.1.4.1.2272.1.3.2.1.35	INTEGER	read-write	This is the encapsulation type for userdefined protocol based vlans. This is not meaningful for other types of vlan. The default value is null.
INT rcVlanFdbAging	1.3.6.1.4.1.2272.1.3.2.1.37	INTEGER	read-write	The timeout period (in seconds) used for aging out fdb entries of this VLAN.
POR rcVlanOspfPassivePortMember	1.3.6.1.4.1.2272.1.3.2.1.44	PortSet	read-write	The set of ports in the vlan that are designated as ospf passive
INT rcVlanNlbMode	1.3.6.1.4.1.2272.1.3.2.1.46	INTEGER	read-write	NLB mode set on a VLAN.
OID rcVlanVrfId	1.3.6.1.4.1.2272.1.3.2.1.48	VrfIdentifier	read-write	Indicates the Virtual Router to which the VLAN belongs
STR rcVlanVrfName	1.3.6.1.4.1.2272.1.3.2.1.49	DisplayString	read-only	The Name of the Virtual Router to which the VLAN belongs
STR rcVlanNodalMepList	1.3.6.1.4.1.2272.1.3.2.1.54	DisplayString	read-write	List of nodal Meps assigned to this vlan. A mep consists of Domain Name, Association name and Mep Id separated by '.'. Each meps is separated by ',': ..,..,... The maximum number of nodal Mep for each vlan is 8.
I32 rcVlanNumOfNodalMep	1.3.6.1.4.1.2272.1.3.2.1.55	Integer32	read-only	Number of nodal meps assigned to this vlan
STR rcVlanNodalMipLevelList	1.3.6.1.4.1.2272.1.3.2.1.56	DisplayString	read-write	List of nodal Mip levels assigned to this vlan that allows Mip functionality to be enabled on a per level per vlan basis. A mip level is represented by an integer ranging from 0 to 7. The mip levels are separated by ',': ,,... The maximum number of nodal Mip levels for each vlan is 8.
I32 rcVlanNumOfNodalMipLevel	1.3.6.1.4.1.2272.1.3.2.1.57	Integer32	read-only	Number of nodal mip levels assigned to this vlan that allows MIP functionality to be enabled on a per level per vlan basis.
I32 rcVlanPlsbIsid	1.3.6.1.4.1.2272.1.3.2.1.61	Integer32	read-write	Plsb i-sid number assigned to a C-vlan. Default 0 value indicates that no i-sid has been assinged.
rcVlanPortTable	1.3.6.1.4.1.2272.1.3.3		not-accessible	A table used to maintain VLAN port related information.
rcVlanPortEntry	1.3.6.1.4.1.2272.1.3.3.1		not-accessible	Entry containing VLAN information regarding a particular port.
I32 rcVlanPortIndex	1.3.6.1.4.1.2272.1.3.3.1.1	Integer32	read-only	An unique index used to identify a particular port in the system. This index is equal to the ifIndex of the port.
I32 rcVlanPortNumVlanIds	1.3.6.1.4.1.2272.1.3.3.1.2	Integer32	read-only	Used to indicate the number of VLAN IDs that are stored in the rcVlanPortVlanIds variable.
INT rcVlanPortType	1.3.6.1.4.1.2272.1.3.3.1.4	INTEGER	read-write	The type of port: access(1) or trunk(2).
T/F rcVlanPortDiscardTaggedFrames	1.3.6.1.4.1.2272.1.3.3.1.5	TruthValue	read-write	A flag used to determine how to process tagged frames received on this access port. When the flag is set, these frames are discarded by the forwarding process. When the flag is reset, these frames are processed normally. This field is meaningless when the port is not an access port and should be set to false(2).
T/F rcVlanPortDiscardUntaggedFrames	1.3.6.1.4.1.2272.1.3.3.1.6	TruthValue	read-write	A flag used to determine how to process untagged frames received on this trunk port. When the flag is set, these frames are discarded by the forwarding process. When the flag is reset, these frames are assigned to the VLAN specified by rcVlanPortDefaultVlanId. This field is meaningless when the port is not a trunk port and should be set to false(2).
INT rcVlanPortDefaultVlanId	1.3.6.1.4.1.2272.1.3.3.1.7	INTEGER	read-write	The VLAN ID assigned to untagged frames received on this trunk port. This field is meaningless when the port is not a trunk port.
T/F rcVlanPortPerformTagging	1.3.6.1.4.1.2272.1.3.3.1.8	TruthValue	read-write	Enable/disable the port on the current vlan to perform tagging on the incoming and outgoing traffic.
T/F rcVlanPortLoopDetect	1.3.6.1.4.1.2272.1.3.3.1.10	TruthValue	read-write	Enable/disable loop detection on this port
NUM rcVlanPortFirstPortInOpid	1.3.6.1.4.1.2272.1.3.3.1.11	InterfaceIndex	read-only	This value gives the IfIndex of the first port in the octapid. This value is used to generate an error message when changing port type from normal to uni/nni and viceversa
NUM rcVlanPortLastPortInOpid	1.3.6.1.4.1.2272.1.3.3.1.12	InterfaceIndex	read-only	This value gives the IfIndex of the first port in the octapid. This value is used to generate an error message when changing port type from normal to uni/nni and viceversa
T/F rcVlanPortUntagDefaultVlan	1.3.6.1.4.1.2272.1.3.3.1.13	TruthValue	read-write	enable/disable Egress Tagging on the Default Vlan of the port.
INT rcVlanPortLoopDetectAction	1.3.6.1.4.1.2272.1.3.3.1.14	INTEGER	read-write	This value is used to specify the action which needs to be taken once a loop is detected on a specific port. VlanBlock is not supported in VSP9000.
T/F rcVlanPortArpDetect	1.3.6.1.4.1.2272.1.3.3.1.15	TruthValue	read-write	Enable/disable Arp detection on this port
T/F rcVlanPortSpoofDetect	1.3.6.1.4.1.2272.1.3.3.1.16	TruthValue	read-write	Enable/disable spoof detection on this port
T/F rcVlanPortClassificationSubnet	1.3.6.1.4.1.2272.1.3.3.1.18	TruthValue	read-write	Enable/disable Subnet based Vlan packets on this port.
T/F rcVlanPortClassificationProtocol	1.3.6.1.4.1.2272.1.3.3.1.19	TruthValue	read-write	Enable/disable Protocol based Vlan packets on this port.
INT rcVlanPortClassificationPrec	1.3.6.1.4.1.2272.1.3.3.1.20	INTEGER	read-write	Sets the precedence for vlan classification. A value of 1 puts classification of packets to source mac vlans ahead of subnet based vlans. A value of 2 puts subnet based vlans ahead of source mac vlans. Classification to other types of vlans is unaffected as it occurs following source mac and subnet based vlans.
OCT rcVlanPortVlanIdList	1.3.6.1.4.1.2272.1.3.3.1.21	OCTET STRING	read-write	This bitfield is used to identify which VLANs this port is assigned to. Each VLAN ID is stored as a bit. The most-significant (left-most) bit represents Vlan Id 1.
T/F rcVlanPortClassificationSourceMac	1.3.6.1.4.1.2272.1.3.3.1.22	TruthValue	read-write	Enable/disable SourceMac based Vlan packets on this port.
rcVlanMacTable	1.3.6.1.4.1.2272.1.3.4		not-accessible	A table used to maintain MAC addresses assigned to a particular VLAN by MAC address.
rcVlanMacEntry	1.3.6.1.4.1.2272.1.3.4.1		not-accessible	Entry containing VLAN information regarding a particular port.
I32 rcVlanMacVlanId	1.3.6.1.4.1.2272.1.3.4.1.1	Integer32	read-only	An unique index used to identify a VLAN (by MAC address) in the system.
MAC rcVlanMacAddr	1.3.6.1.4.1.2272.1.3.4.1.2	MacAddress	read-only	An unique index used to identify a MAC address assigned to a particular VLAN.
ROW rcVlanMacRowStatus	1.3.6.1.4.1.2272.1.3.4.1.3	RowStatus	read-write	Row status for this entry.
I32 rcVlanIgmpSnoopNumGroups	1.3.6.1.4.1.2272.1.3.5	Integer32	read-only	The number of entries (rows) in the rcVlanIgmpSnoopTable.
rcVlanLoopDetectedTable	1.3.6.1.4.1.2272.1.3.10		not-accessible	A list of Vlans the port belongs to and the corresponding loop detected status.
rcVlanLoopDetectedEntry	1.3.6.1.4.1.2272.1.3.10.1		not-accessible	Loop-Detected Entry.
I32 rcVlanLoopDetectedPortIndex	1.3.6.1.4.1.2272.1.3.10.1.1	Integer32	read-only	Port Number.
I32 rcVlanLoopDetectedVlanId	1.3.6.1.4.1.2272.1.3.10.1.2	Integer32	read-only	Gives the VlanId to which the port belongs.
INT rcVlanLoopDetectedValue	1.3.6.1.4.1.2272.1.3.10.1.3	INTEGER	read-only	Gives the Loop Detected status of the port in a vlan.
rcVlanDsapSsapTable	1.3.6.1.4.1.2272.1.3.11		not-accessible	A table used to maintain DSAP/SSAP values assigned to a sna802dot2 or userdefined vlan.
rcVlanDsapSsapEntry	1.3.6.1.4.1.2272.1.3.11.1		not-accessible	An entry in the rcVlanDsapSsap table.
I32 rcVlanDsapSsapVlanId	1.3.6.1.4.1.2272.1.3.11.1.1	Integer32	not-accessible	A unique index to identify a vlan.
INT rcVlanDsapSsapPid	1.3.6.1.4.1.2272.1.3.11.1.2	INTEGER	not-accessible	Values of DSAP/SSAP assigned to a particular vlan.
ROW rcVlanDsapSsapRowStatus	1.3.6.1.4.1.2272.1.3.11.1.3	RowStatus	read-write	Row Status.
rcVlanNewLoopDetectedTable	1.3.6.1.4.1.2272.1.3.12		not-accessible	A list of Vlans the port belongs to and the corresponding loop detected status.
rcVlanNewLoopDetectedEntry	1.3.6.1.4.1.2272.1.3.12.1		not-accessible	Loop-Detected Entry.
NUM rcVlanNewLoopDetectedPortIndex	1.3.6.1.4.1.2272.1.3.12.1.1	InterfaceIndex	not-accessible	Port Number.
I32 rcVlanNewLoopDetectedVlanId	1.3.6.1.4.1.2272.1.3.12.1.2	Integer32	not-accessible	Gives the VlanId to which the port belongs.
MAC rcVlanNewLoopDetectedMac	1.3.6.1.4.1.2272.1.3.12.1.3	MacAddress	not-accessible	Mac address
INT rcVlanNewLoopDetectedAction	1.3.6.1.4.1.2272.1.3.12.1.4	INTEGER	read-only	This value is used to specify the action which needs to be taken once a loop is detected on a specific port.
T/F rcVlanNewLoopDetectedSmltRemote	1.3.6.1.4.1.2272.1.3.12.1.5	TruthValue	read-only	A MAC address indicate for remote learnt, either local or remote.
rcChassis	1.3.6.1.4.1.2272.1.4
INT rcChasType	1.3.6.1.4.1.2272.1.4.1	INTEGER	read-only	Chassis Type
STR rcChasSerialNumber	1.3.6.1.4.1.2272.1.4.2	DisplayString	read-only	Unique serial number for this chassis.
STR rcChasHardwareRevision	1.3.6.1.4.1.2272.1.4.3	DisplayString	read-only	Device hardware revision level
INT rcChasNumSlots	1.3.6.1.4.1.2272.1.4.4	INTEGER	read-only	The number of slots in the chassis available for plug-in cards.
INT rcChasNumPorts	1.3.6.1.4.1.2272.1.4.5	INTEGER	read-only	The total number of ports currently installed in the chassis.
rcChasFan	1.3.6.1.4.1.2272.1.4.7
rcChasFanZoneTable	1.3.6.1.4.1.2272.1.4.7.2		not-accessible	Table for the zones available on the chassis
rcChasFanZoneEntry	1.3.6.1.4.1.2272.1.4.7.2.1		not-accessible	Contains information regarding a zone unit
INT rcChasFanZoneType	1.3.6.1.4.1.2272.1.4.7.2.1.1	INTEGER	not-accessible	Type of the fan zone.
INT rcChasFanZoneMode	1.3.6.1.4.1.2272.1.4.7.2.1.2	INTEGER	read-only	Functional mode of the fan zone.
BIT rcChasFanZoneModeStatus	1.3.6.1.4.1.2272.1.4.7.2.1.3	Bits	read-only	Bit set indicates the alarm type(s)
I32 rcChasFanZoneAlarmTimer	1.3.6.1.4.1.2272.1.4.7.2.1.4	Integer32	read-only	Alarm timer indicates the remaining time before system checks and shutdown module when fan is in the alarm state. Zero means the fan i snot in an alarm state
G32 rcChasFanZoneTemperature	1.3.6.1.4.1.2272.1.4.7.2.1.5	Gauge32	read-only	Highest temperature measured in celsius degree from all the sensors (inlet and outlet) in the zone
INT rcChasFanZoneTray1LedColor	1.3.6.1.4.1.2272.1.4.7.2.1.6	INTEGER	read-only	Led color indicate fans operation status on tray off: Indicates no tray or power off. green: Indicates all fans are operational in a tray. red: Front Zone Tray: more than one fans in a tray are not opertional. Rear Zone Tray: one of two or both fans fans in a tray are not operational. amber: Front Zone Tray: one of eight fans is not operational. Rear Zone Tray: It is not applicable for Rear Zone tray
INT rcChasFanZoneTray2LedColor	1.3.6.1.4.1.2272.1.4.7.2.1.7	INTEGER	read-only	Led color indicate fans operation status on tray off: Indicates no tray or power off. green: Indicates all fans are operational in a tray. red: Front Zone Tray: more than one fans in a tray are not opertional. Rear Zone Tray: one of two fans or both fans in a tray are not operational. amber: Front Zone Tray: one of eight fans is not operational. Rear Zone Tray: It is not applicable for Rear Zone tray
rcChasFanInfoTable	1.3.6.1.4.1.2272.1.4.7.3		not-accessible	This table contains information for all the fans on the chassis
rcChasFanInfoEntry	1.3.6.1.4.1.2272.1.4.7.3.1		not-accessible	Contains information regarding a fan unit
INT rcChasFanInfoTray	1.3.6.1.4.1.2272.1.4.7.3.1.1	INTEGER	not-accessible	Number of trays per zone in chassis
INT rcChasFanInfoFan	1.3.6.1.4.1.2272.1.4.7.3.1.2	INTEGER	not-accessible	Number of fans per tray
INT rcChasFanInfoExpectedSpeed	1.3.6.1.4.1.2272.1.4.7.3.1.3	INTEGER	read-only	The administrative setting for the fan speed low: Low speed set by software medium: Medium speed set by software high: High speed set by software hardware: Speed controlled by hardware
INT rcChasFanInfoOperSpeed	1.3.6.1.4.1.2272.1.4.7.3.1.4	INTEGER	read-only	Actual speed of the fan
INT rcChasFanInfoStatus	1.3.6.1.4.1.2272.1.4.7.3.1.5	INTEGER	read-only	The operational status of the fan. Details below: ok(1): Fan operating under normal condition(s) faulty(2): Fan not operating as expected
rcChasPowerSupply	1.3.6.1.4.1.2272.1.4.8
rcChasPowerSupplyTable	1.3.6.1.4.1.2272.1.4.8.1		not-accessible	This table contains information about power supplies.
rcChasPowerSupplyEntry	1.3.6.1.4.1.2272.1.4.8.1.1		not-accessible	Contains information regarding a power supply unit.
INT rcChasPowerSupplyId	1.3.6.1.4.1.2272.1.4.8.1.1.1	INTEGER	read-only	The power supply Id.
INT rcChasPowerSupplyOperStatus	1.3.6.1.4.1.2272.1.4.8.1.1.2	INTEGER	read-only	Actual status of the power supply: - unknown(1) - status can not be determined. - empty(2) - power supply not installed. - up(3) - present and supplying power. - down(4) - present, but failure indicated.
rcChasPowerSupplyDetailTable	1.3.6.1.4.1.2272.1.4.8.2		not-accessible	This table contains detailed information about power supplies.
rcChasPowerSupplyDetailEntry	1.3.6.1.4.1.2272.1.4.8.2.1		not-accessible	Contains detailed info regarding a power supply unit.
INT rcChasPowerSupplyDetailId	1.3.6.1.4.1.2272.1.4.8.2.1.1	INTEGER	read-only	The power supply Id.
INT rcChasPowerSupplyDetailType	1.3.6.1.4.1.2272.1.4.8.2.1.2	INTEGER	read-only	The power supply type.
STR rcChasPowerSupplyDetailSerialNumber	1.3.6.1.4.1.2272.1.4.8.2.1.3	DisplayString	read-only	The power supply serial number.
STR rcChasPowerSupplyDetailHardwareRevision	1.3.6.1.4.1.2272.1.4.8.2.1.4	DisplayString	read-only	The hardware revision of the power supply.
STR rcChasPowerSupplyDetailPartNumber	1.3.6.1.4.1.2272.1.4.8.2.1.5	DisplayString	read-only	The power supply part number.
STR rcChasPowerSupplyDetailDescription	1.3.6.1.4.1.2272.1.4.8.2.1.6	DisplayString	read-only	The detail description of power supply.
INT rcChasPowerSupplyDetailInputLineVoltage	1.3.6.1.4.1.2272.1.4.8.2.1.8	INTEGER	read-only	The power supply Input Line voltage.
I32 rcChasPowerSupplyDetailOutputWatts	1.3.6.1.4.1.2272.1.4.8.2.1.10	Integer32	read-only	The output power of this power supply
rcCard	1.3.6.1.4.1.2272.1.4.9
rcCardTable	1.3.6.1.4.1.2272.1.4.9.1		not-accessible	A table that contains information about the cards in this chassis. For those slots that do not contain a physical card, the table may be implemented to contain a conceptual row with the type of physical module set to 'chasCardEmpty', or it may be implemented to have no conceptual row instance.
rcCardEntry	1.3.6.1.4.1.2272.1.4.9.1.1		not-accessible	Card attributes
INT rcCardIndex	1.3.6.1.4.1.2272.1.4.9.1.1.1	INTEGER	read-only	A unique value for each module within the chassis. This value is determined by the chassis slot number where the module is inserted. Valid entries are 1 to the value of rcChasNumSlots
INT rcCardType	1.3.6.1.4.1.2272.1.4.9.1.1.2	INTEGER	read-only	Used to indicate the card type. The value returned is defined by the description in rc2kCardTable.
STR rcCardOxateCpld	1.3.6.1.4.1.2272.1.4.9.1.1.9	DisplayString	read-only	Oxate CPLD version for CP card
STR rcCardOxideFpga	1.3.6.1.4.1.2272.1.4.9.1.1.10	DisplayString	read-only	Oxide FGPA version for CP card
STR rcCardCatskillFpga	1.3.6.1.4.1.2272.1.4.9.1.1.11	DisplayString	read-only	Catskill FPGA version for CP card
STR rcCardQE	1.3.6.1.4.1.2272.1.4.9.1.1.12	DisplayString	read-only	QE version for CP card
STR rcCardK2Fpga	1.3.6.1.4.1.2272.1.4.9.1.1.13	DisplayString	read-only	K2 FPGA version for IO card
STR rcCardIoDateDC	1.3.6.1.4.1.2272.1.4.9.1.1.14	DisplayString	read-only	IO Date DC CPLD for IO card
STR rcCardIoDateBB	1.3.6.1.4.1.2272.1.4.9.1.1.15	DisplayString	read-only	IO Date BaseBoard CPLD for IO card
STR rcCardIoPimCpld	1.3.6.1.4.1.2272.1.4.9.1.1.16	DisplayString	read-only	IO PIM CPLD for IO card
STR rcCardLed0Cpld	1.3.6.1.4.1.2272.1.4.9.1.1.17	DisplayString	read-only	LED0 CPLD for IO card
STR rcCardLed1Cpld	1.3.6.1.4.1.2272.1.4.9.1.1.18	DisplayString	read-only	LED1 CPLD for IO card
STR rcCardZagrosFpga	1.3.6.1.4.1.2272.1.4.9.1.1.19	DisplayString	read-only	Zagros FPGA for IO card
STR rcCardRsp	1.3.6.1.4.1.2272.1.4.9.1.1.20	DisplayString	read-only	RSP for IO card
STR rcCardBcmMac	1.3.6.1.4.1.2272.1.4.9.1.1.21	DisplayString	read-only	BCM Mac for IO card
STR rcCardPhosphideFpga	1.3.6.1.4.1.2272.1.4.9.1.1.22	DisplayString	read-only	Phosphide FPGA for IO card
STR rcCardSulfideFpga	1.3.6.1.4.1.2272.1.4.9.1.1.23	DisplayString	read-only	Sulfide FPGA for IO card
STR rcCardFluorateCpld	1.3.6.1.4.1.2272.1.4.9.1.1.24	DisplayString	read-only	Fluorate Cpld for SF card
STR rcCardBme	1.3.6.1.4.1.2272.1.4.9.1.1.25	DisplayString	read-only	BME for SF card
rcPort	1.3.6.1.4.1.2272.1.4.10
rcPortTable	1.3.6.1.4.1.2272.1.4.10.1		not-accessible	Port table
rcPortEntry	1.3.6.1.4.1.2272.1.4.10.1.1		not-accessible	Entry containing info. for a particular port
NUM rcPortIndex	1.3.6.1.4.1.2272.1.4.10.1.1.1	InterfaceIndex	read-only	An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.
INT rcPortType	1.3.6.1.4.1.2272.1.4.10.1.1.2	INTEGER	read-only	Port type
INT rcPortAction	1.3.6.1.4.1.2272.1.4.10.1.1.6	INTEGER	read-write	Port related actions.
INT rcPortResult	1.3.6.1.4.1.2272.1.4.10.1.1.7	INTEGER	read-only	Result from the last Vlan action.
T/F rcPortAutoNegotiate	1.3.6.1.4.1.2272.1.4.10.1.1.11	TruthValue	read-write	Indicate whether this port enabled for auto negotiations or not.
INT rcPortAdminDuplex	1.3.6.1.4.1.2272.1.4.10.1.1.12	INTEGER	read-write	Indicates the port duplex type
INT rcPortOperDuplex	1.3.6.1.4.1.2272.1.4.10.1.1.13	INTEGER	read-only	Indicate this port's current duplex value.
INT rcPortAdminSpeed	1.3.6.1.4.1.2272.1.4.10.1.1.14	INTEGER	read-write	Indicate this port's speed.
I32 rcPortOperSpeed	1.3.6.1.4.1.2272.1.4.10.1.1.15	Integer32	read-only	Indicate this port's current speed value.
I32 rcPortMltId	1.3.6.1.4.1.2272.1.4.10.1.1.16	Integer32	read-only	Indicate which multi-link trunk (MLT) this port is assigned to. If this port is not associated with any MLT, this value will be set to zero(0).
T/F rcPortLocked	1.3.6.1.4.1.2272.1.4.10.1.1.17	TruthValue	read-only	Indicate whether this port is locked.
T/F rcPortAutoNegotiationSupported	1.3.6.1.4.1.2272.1.4.10.1.1.18	TruthValue	read-only	Indicate whether this port can support auto-negotiation.
T/F rcPortSingleRoutablePort	1.3.6.1.4.1.2272.1.4.10.1.1.19	TruthValue	read-only	Indicate whether this port is a single routable port. If this value is true, the port functions like a traditional router port.
T/F rcPortUnknownMacDiscard	1.3.6.1.4.1.2272.1.4.10.1.1.20	TruthValue	read-write	If rcUnknownMacDiscard is set to True, then a packet with an unknown source MAC address is dropped on that port, and other ports then will discard any packets with this MAC address in the destination field. For example, suppose 11:22:33:44:55:66 is an unknown source MAC, packets with source MAC 11:22:33:44:55 coming from this port is discarded, further more, packets with destination MAC 11:22:33:44:55:66 coming from other ports are also discarded, unless this address is later learned on another port or the restriction ages out.
C32 rcPortNumStateTransition	1.3.6.1.4.1.2272.1.4.10.1.1.21	Counter32	read-only	# state transitions.
INT rcPortQosLevel	1.3.6.1.4.1.2272.1.4.10.1.1.30	INTEGER	read-write	Used to specify the Qos level packets, carried on this port, should be processed with.
T/F rcPortDiffServEnable	1.3.6.1.4.1.2272.1.4.10.1.1.31	TruthValue	read-write	Used to enable/disable the Differentiated Service feature on this port.
INT rcPortDiffServType	1.3.6.1.4.1.2272.1.4.10.1.1.32	INTEGER	read-write	Used to specify the Differentiated Service type for this port.
STR rcPortVendorDescr	1.3.6.1.4.1.2272.1.4.10.1.1.34	DisplayString	read-only	Used to show the name of the vendor of this port's connector. Only applicable to ports on a GBIC cards.
STR rcPortName	1.3.6.1.4.1.2272.1.4.10.1.1.35	DisplayString	read-write	This port's name.
ENA rcPortAdminRouting	1.3.6.1.4.1.2272.1.4.10.1.1.43	EnableValue	read-write	Indicate whether the port is routable.
ENA rcPortOperRouting	1.3.6.1.4.1.2272.1.4.10.1.1.44	EnableValue	read-only	The status of the port whether is routable.
T/F rcPortIeee8021POverrideEnable	1.3.6.1.4.1.2272.1.4.10.1.1.46	TruthValue	read-write	Used to enable/disable IEEE 802.1P override. If it is enabled, 802.1p value from a tagged frame may not be honored.
T/F rcPortHighSecureEnable	1.3.6.1.4.1.2272.1.4.10.1.1.51	TruthValue	read-write	Enable/Disable high secure feature.
INT rcPortMrouteStrLimit	1.3.6.1.4.1.2272.1.4.10.1.1.55	INTEGER	read-write	maximum number of multicast streams that are allowed to ingress to CPU through this port.
INT rcPortMrouteStrTimerCheck	1.3.6.1.4.1.2272.1.4.10.1.1.56	INTEGER	read-write	sampling period to check number of multicast streams that has ingressed CPU through this port in seconds.
T/F rcPortMrouteStrLimitEnable	1.3.6.1.4.1.2272.1.4.10.1.1.57	TruthValue	read-write	enable or disable mroute stream limit on port.
BIT rcPortAutoNegAd	1.3.6.1.4.1.2272.1.4.10.1.1.62	Bits	read-write	This object is used to specify the port speed and duplex abilities to be advertised during link negotiation. bit 0 - 10 half duplex advertised bit 1 - 10 full duplex advertised bit 2 - 100 half duplex advertised bit 3 - 100 full duplex advertised bit 5 - 1000 full duplex advertised bit 6 - Mac PAUSE frame support advertised bit 7 - Asymmetric PAUSE frame support advertised bit 8 - No advertisements The abilities specified in this object are only used when auto-negotiation is enabled on the port. If all bits in this object are disabled, and auto-negotiation is enabled on the port, then the physical link process on the port will be disabled (if hardware supports this ability). Any change in the value of this bit map will force the PHY to restart the auto-negotiation process. This will have the same effect as physically unplugging and reattaching the cable plant attached to this port. The capabilities being advertised are either all the capabilities supported by the hardware or the user- configured capabilities which is a subset of all the capability supported by hardware. The default value for this object will be all the capabilities supported by the hardware. Note that bit 6 and bit 7 are currently not supported in ERS8600.
T/F rcPortAutoRecoverPort	1.3.6.1.4.1.2272.1.4.10.1.1.64	TruthValue	read-write	enable or disable auto recovery of port from action taken by cp-limit, link flap or loop detect features
INT rcPortEgressRateLimit	1.3.6.1.4.1.2272.1.4.10.1.1.67	INTEGER	read-write	Egress Rate Limit. for VSP 9000, range is 10000 to 10000000
ENA rcPortEgressRateLimitState	1.3.6.1.4.1.2272.1.4.10.1.1.68	EnableValue	read-write	Used to enable/disable shape/egress-rate-limit functionality.
INT rcPortIngressRateLimit	1.3.6.1.4.1.2272.1.4.10.1.1.85	INTEGER	read-write	Limits the amount of traffic from this Ingress port.
IDL rcPortVrfIdList	1.3.6.1.4.1.2272.1.4.10.1.1.87	IdList	read-only	The set of VRF ids to which this port belongs.
OCT rcPortVrfNameList	1.3.6.1.4.1.2272.1.4.10.1.1.96	OCTET STRING	read-only	The set of VRF names to which this port belongs.
OID rcPortBrouterVrfId	1.3.6.1.4.1.2272.1.4.10.1.1.97	VrfIdentifier	read-write	Gives the VRF Id for this Brouter port.
STR rcPortBrouterVrfName	1.3.6.1.4.1.2272.1.4.10.1.1.98	DisplayString	read-only	Gives the VRF Name for this Brouter port.
C32 rcPortVrfCount	1.3.6.1.4.1.2272.1.4.10.1.1.99	Counter32	read-only	The total number of VRFs this port is associated to.
INT rcPortIngressRatePeak	1.3.6.1.4.1.2272.1.4.10.1.1.108	INTEGER	read-write	Peak rate limit for this port. 0 means disable
INT rcPortIngressRateSvc	1.3.6.1.4.1.2272.1.4.10.1.1.109	INTEGER	read-write	Service rate limit for this port. 0 mean deisable
INT rcPortCpLimitPktRate	1.3.6.1.4.1.2272.1.4.10.1.1.110	INTEGER	read-write	Used to limit Control packets on the port to qos-levels 6 and 7. Sets the limit in packets per second.
T/F rcPortCpLimitShutDownEnable	1.3.6.1.4.1.2272.1.4.10.1.1.111	TruthValue	read-write	Used to indicate if the port should be shutdown when the CpLimitPktRate is exceeded.
rcPortPcapTable	1.3.6.1.4.1.2272.1.4.10.2		not-accessible	Port pcap Table
rcPortPcapEntry	1.3.6.1.4.1.2272.1.4.10.2.1		not-accessible	Entry containing pcap info. for a particular port
NUM rcPortPcapIndex	1.3.6.1.4.1.2272.1.4.10.2.1.1	InterfaceIndex	read-only	An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.
T/F rcPortPcapEnable	1.3.6.1.4.1.2272.1.4.10.2.1.2	TruthValue	read-write	To enable pcap for the port
INT rcPortPcapMode	1.3.6.1.4.1.2272.1.4.10.2.1.3	INTEGER	read-write	Mode in which pcap is enabled
rcPortLacpTable	1.3.6.1.4.1.2272.1.4.10.4		not-accessible	Port LACP table
rcPortLacpEntry	1.3.6.1.4.1.2272.1.4.10.4.1		not-accessible	Entry containing info. for a particular port
T/F rcPortLacpAdminEnable	1.3.6.1.4.1.2272.1.4.10.4.1.1	TruthValue	read-write	Administratively enable/disable LACP on a port
T/F rcPortLacpOperEnable	1.3.6.1.4.1.2272.1.4.10.4.1.2	TruthValue	read-only	Indicates if LACP is operationally enabled or disabled on a port
INT rcPortLacpFastPeriodicTime	1.3.6.1.4.1.2272.1.4.10.4.1.3	INTEGER	read-write	The number of miliseconds between periodic transmissions using Short Timeouts.
INT rcPortLacpSlowPeriodicTime	1.3.6.1.4.1.2272.1.4.10.4.1.4	INTEGER	read-write	The number of miliseconds between periodic transmissions using LONG Timeouts.
INT rcPortLacpTimeoutScale	1.3.6.1.4.1.2272.1.4.10.4.1.5	INTEGER	read-write	Scalar value used to calculate timeout time from periodic time. Timeout = PeriodicTime * TimeoutScale
INT rcPortLacpAggrWaitTime	1.3.6.1.4.1.2272.1.4.10.4.1.6	INTEGER	read-write	The number of mili seconds to delay aggregation to allow multiple links to aggregate simultaneously.
INT rcPortLacpFastPeriodicTimeOper	1.3.6.1.4.1.2272.1.4.10.4.1.7	INTEGER	read-only	The operating value of fast periodic timer on the port.
INT rcPortLacpSlowPeriodicTimeOper	1.3.6.1.4.1.2272.1.4.10.4.1.8	INTEGER	read-only	The operating value of slow periodic timer on the port.
INT rcPortLacpTimeoutScaleOper	1.3.6.1.4.1.2272.1.4.10.4.1.9	INTEGER	read-only	The operating value of timeout scale on the port.
INT rcPortLacpAggrWaitTimeOper	1.3.6.1.4.1.2272.1.4.10.4.1.10	INTEGER	read-only	The operating value of aggreagate wait time on port.
rcPortVLacpTable	1.3.6.1.4.1.2272.1.4.10.5		not-accessible	Port Virtual LACP table
rcPortVLacpEntry	1.3.6.1.4.1.2272.1.4.10.5.1		not-accessible	Entry containing info. for a particular port
T/F rcPortVLacpAdminEnable	1.3.6.1.4.1.2272.1.4.10.5.1.1	TruthValue	read-write	Administratively enable/disable Virtual LACP on a port
T/F rcPortVLacpOperEnable	1.3.6.1.4.1.2272.1.4.10.5.1.2	TruthValue	read-only	Indicates if Virtual LACP is operationally enabled or disabled on a port
INT rcPortVLacpFastPeriodicTimer	1.3.6.1.4.1.2272.1.4.10.5.1.3	INTEGER	read-write	The number of miliseconds between periodic transmissions using Short Timeouts
INT rcPortVLacpSlowPeriodicTimer	1.3.6.1.4.1.2272.1.4.10.5.1.4	INTEGER	read-write	The number of miliseconds between periodic transmissions using LONG Timeouts.
INT rcPortVLacpTimeout	1.3.6.1.4.1.2272.1.4.10.5.1.5	INTEGER	read-write	Timeout control value. Long or Short Timeout
INT rcPortVLacpTimeoutScale	1.3.6.1.4.1.2272.1.4.10.5.1.6	INTEGER	read-write	Scalar value used to calculate timeout time from periodic time. Timeout = PeriodicTime * TimeoutScale
I32 rcPortVLacpEtherType	1.3.6.1.4.1.2272.1.4.10.5.1.7	Integer32	read-write	VLACP Protocol Identification. The id value is in Hex. Range in hex (0x600..0xffff)
MAC rcPortVLacpEtherMacAddress	1.3.6.1.4.1.2272.1.4.10.5.1.8	MacAddress	read-write	Multicast Mac Address exclusively used for VLACPDU's
INT rcPortVLacpPortState	1.3.6.1.4.1.2272.1.4.10.5.1.9	INTEGER	read-only	Display the Vlacp Port State.
rcPortRemoteMirroringTable	1.3.6.1.4.1.2272.1.4.10.6		not-accessible	Port Remote Mirroring Table
rcPortRemoteMirroringEntry	1.3.6.1.4.1.2272.1.4.10.6.1		not-accessible	Entry containing remote mirroring info. for a particular port
NUM rcPortRemoteMirroringIndex	1.3.6.1.4.1.2272.1.4.10.6.1.1	InterfaceIndex	read-only	An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.
T/F rcPortRemoteMirroringEnable	1.3.6.1.4.1.2272.1.4.10.6.1.2	TruthValue	read-write	To enable remote Mirroring for the port
INT rcPortRemoteMirroringMode	1.3.6.1.4.1.2272.1.4.10.6.1.3	INTEGER	read-write	Mode in which remote mirroring is enabled
MAC rcPortRemoteMirroringSrcMac	1.3.6.1.4.1.2272.1.4.10.6.1.4	MacAddress	read-write	Source Mac of the remote mirrored packet. Remote mirroring packet will be send with this source mac address
MAC rcPortRemoteMirroringDstMac	1.3.6.1.4.1.2272.1.4.10.6.1.5	MacAddress	read-write	Destination Mac of the remote mirrored packet. Packets will be bridged to this mac address. Remote mirroring packet will be send to this mac address
INT rcPortRemoteMirroringEtherType	1.3.6.1.4.1.2272.1.4.10.6.1.6	INTEGER	read-write	Ethertype of the remote mirrored packet. Packets will be send with this ethertype
INT rcPortRemoteMirroringVlanIdListSize	1.3.6.1.4.1.2272.1.4.10.6.1.7	INTEGER	read-only	Used to indicate the number of VLAN IDs that are assigned to this port.
OCT rcPortRemoteMirroringVlanIdList	1.3.6.1.4.1.2272.1.4.10.6.1.8	OCTET STRING	read-write	This field is used only if the port is assigned as remote mirroring termination port. Represents zero or more filter lists vlan in which the Destination Mac address resides. Each VLAN ID is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.
ROW rcPortRemoteMirroringRowStatus	1.3.6.1.4.1.2272.1.4.10.6.1.9	RowStatus	read-write	RowStatus
rcPortLosslessEnetTable	1.3.6.1.4.1.2272.1.4.10.13		not-accessible	Port Lossless Ethernet Table
rcPortLosslessEnetEntry	1.3.6.1.4.1.2272.1.4.10.13.1		not-accessible	Entry containing lossless Ethernet information for a particular port.
NUM rcPortLosslessEnetIndex	1.3.6.1.4.1.2272.1.4.10.13.1.1	InterfaceIndex	not-accessible	An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2. Lossless Ethernet will be limited to 10Gig ports.
T/F rcPortLosslessEnetConfigured	1.3.6.1.4.1.2272.1.4.10.13.1.2	TruthValue	read-write	To enable lossless mode for the port
INT rcPortLosslessEnetPauseType	1.3.6.1.4.1.2272.1.4.10.13.1.3	INTEGER	read-write	Pause frame type. fc - Pause, pfc - priority-based flow control.
I32 rcPortLosslessEnetPfcBandwidth	1.3.6.1.4.1.2272.1.4.10.13.1.4	Integer32	read-write	Guaranteed bandwidth in Gbps when rcPortLosslessEnetPauseType is set to pfc(2).
rcPortLock	1.3.6.1.4.1.2272.1.4.11
T/F rcPortLockEnable	1.3.6.1.4.1.2272.1.4.11.1	TruthValue	read-write	Indicate whether the port lock feature is enabled.
POR rcPortLockLockedPorts	1.3.6.1.4.1.2272.1.4.11.2	PortSet	read-write	The set of ports that are administratively locked. Locked ports cannot be modified in anyway until the port is unlocked first.
POR rcChasBrouterPorts	1.3.6.1.4.1.2272.1.4.17	PortSet	read-only	Used to indicate which ports in the system are configured as Brouter ports.
T/F rcChasFtpDaemonInSecondaryCpu	1.3.6.1.4.1.2272.1.4.26	TruthValue	read-write	Used to enable/disable FTP daemon in 2nd cpu.
T/F rcChasNewVlanOptmMode	1.3.6.1.4.1.2272.1.4.28	TruthValue	read-write	Vlan Optimization mode.
T/F rcChasVlanOptmMode	1.3.6.1.4.1.2272.1.4.29	TruthValue	read-only	Vlan Optimization mode the switch currently has booted and will remain the same until the next reboot.
T/F rcChasRspMode	1.3.6.1.4.1.2272.1.4.35	TruthValue	read-write	This configuration is for enabling/disabling 256K mode. The change will take effect upon reboot.
T/F rcChasRspOperMode	1.3.6.1.4.1.2272.1.4.36	TruthValue	read-only	R-mode the switch currently has booted and will remain the same until the next reboot.
INT rcChasRspModeError	1.3.6.1.4.1.2272.1.4.37	INTEGER	read-only	Used to indicate the r-mode error status
I32 rcChasNewMulticastResourceReservation	1.3.6.1.4.1.2272.1.4.44	Integer32	read-write	Used to reserve MGIDs for IP Multicast. The change will take effect upon reboot.
I32 rcChasMulticastResourceReservation	1.3.6.1.4.1.2272.1.4.45	Integer32	read-only	MGIDs the switch currently has reserved for IP Multicast; will remain the same until the next reboot.
ENA rcChasNewMaxVlanResourceReservation	1.3.6.1.4.1.2272.1.4.46	EnableValue	read-write	A mode where all MGIDs are reserved for VLAN use only; no IPMC. The change will take effect upon reboot.
ENA rcChasMaxVlanResourceReservation	1.3.6.1.4.1.2272.1.4.47	EnableValue	read-only	Tells if all MGIDs are reserved for VLAN use. Will remain the same until the next reboot.
I32 rcChasMgidUsageVlanCurrent	1.3.6.1.4.1.2272.1.4.48	Integer32	read-only	Number of MGIDs currently used for VLAN, including SMLT
I32 rcChasMgidUsageVlanRemaining	1.3.6.1.4.1.2272.1.4.49	Integer32	read-only	Number of MGIDs remaining allocated for VLAN
I32 rcChasMgidUsageMulticastCurrent	1.3.6.1.4.1.2272.1.4.50	Integer32	read-only	Number of MGIDs currently used for IPMC
I32 rcChasMgidUsageMulticastRemaining	1.3.6.1.4.1.2272.1.4.51	Integer32	read-only	Number of MGIDs remaining allocated for IPMC
T/F rcChasForceTopologyIpFlagEnable	1.3.6.1.4.1.2272.1.4.53	TruthValue	read-write	Used to enable/disable flag which is used to set the CLIP-ip as topology ip
I32 rcChasCircuitlessIpId	1.3.6.1.4.1.2272.1.4.54	Integer32	read-write	The Clip-Id set by the user to be used as Topology-ip. '0' means no circuitless IP id while '1..256' is valid circuitless Id
rcMirror	1.3.6.1.4.1.2272.1.5
rcDipSwitch	1.3.6.1.4.1.2272.1.6
rcTblSize	1.3.6.1.4.1.2272.1.7
I32 rcTblRmonStatSize	1.3.6.1.4.1.2272.1.7.1	Integer32	read-only	Used to indicate the current size of the RMON Statistic table.
I32 rcTblRmonHistoryControlSize	1.3.6.1.4.1.2272.1.7.2	Integer32	read-only	Used to indicate the current size of the RMON History Control table.
I32 rcTblRmonHistoryEnetSize	1.3.6.1.4.1.2272.1.7.3	Integer32	read-only	Used to indicate the current size of the RMON History Ethernet table.
I32 rcTblRmonAlarmSize	1.3.6.1.4.1.2272.1.7.4	Integer32	read-only	Used to indicate the current size of the RMON Alarm table.
I32 rcTblRmonEventSize	1.3.6.1.4.1.2272.1.7.5	Integer32	read-only	Used to indicate the current size of the RMON Event table.
I32 rcTblRmonLogSize	1.3.6.1.4.1.2272.1.7.6	Integer32	read-only	Used to indicate the current size of the RMON Log table.
I32 rcTblArTblSize	1.3.6.1.4.1.2272.1.7.7	Integer32	read-only	Used to indicate the size of the Address Translation (AR) table.
I32 rcTblArFree	1.3.6.1.4.1.2272.1.7.8	Integer32	read-only	Used to indicate the number of free entries that are available in the Address Translation (AR) table.
I32 rcTblArNoSpace	1.3.6.1.4.1.2272.1.7.9	Integer32	read-only	Used to indicate the number of entries that could not be added to the Address Translation (AR) table due to lack of space.
I32 rcTblArAdded	1.3.6.1.4.1.2272.1.7.10	Integer32	read-only	Used to indicate the number of entries added to the Address Translation (AR) table.
I32 rcTblArDeleted	1.3.6.1.4.1.2272.1.7.11	Integer32	read-only	Used to indicate the number of entries deleted to the Address Translation (AR) table.
I32 rcTblArMacAdded	1.3.6.1.4.1.2272.1.7.12	Integer32	read-only	Used to indicate the number of MAC entries added to the Address Translation (AR) table.
I32 rcTblArMacDeleted	1.3.6.1.4.1.2272.1.7.13	Integer32	read-only	Used to indicate the number of MAC entries deleted to the Address Translation (AR) table.
I32 rcTblArMacMoved	1.3.6.1.4.1.2272.1.7.14	Integer32	read-only	Used to indicate the number of MAC entries moved in the Address Translation (AR) table.
I32 rcTblArIpAdded	1.3.6.1.4.1.2272.1.7.15	Integer32	read-only	Used to indicate the number of IP entries added to the Address Translation (AR) table.
I32 rcTblArIpDeleted	1.3.6.1.4.1.2272.1.7.16	Integer32	read-only	Used to indicate the number of IP entries deleted to the Address Translation (AR) table.
I32 rcTblArMcastTblSize	1.3.6.1.4.1.2272.1.7.17	Integer32	read-only	Used to indicate the size of the Multicast Address Translation (AR) table.
I32 rcTblArFreeMcastGroups	1.3.6.1.4.1.2272.1.7.18	Integer32	read-only	Used to indicate the number of free multicast groups availabe in the Address Translation (AR) table.
I32 rcTblArIpMcastAdded	1.3.6.1.4.1.2272.1.7.19	Integer32	read-only	Used to indicate the number of Ip multicast entries that are added to the Address Translation (AR) table.
I32 rcTblArIpMcastDeleted	1.3.6.1.4.1.2272.1.7.20	Integer32	read-only	Used to indicate the number of Ip multicast entries that are deleted from the Address Translation (AR) table.
I32 rcTblArVlanByPortAdded	1.3.6.1.4.1.2272.1.7.21	Integer32	read-only	Used to indicate the number of VLAN by port entries that are added to the Address Translation (AR) table.
I32 rcTblArVlanByPortDeleted	1.3.6.1.4.1.2272.1.7.22	Integer32	read-only	Used to indicate the number of VLAN by port entries that are deleted from the Address Translation (AR) table.
I32 rcTblArVlanByProtocolAdded	1.3.6.1.4.1.2272.1.7.23	Integer32	read-only	Used to indicate the number of Vlans by Protocol Type entries that are added to the Address Translation (AR) table.
I32 rcTblArVlanByProtocolDeleted	1.3.6.1.4.1.2272.1.7.24	Integer32	read-only	Used to indicate the number of Vlans by Protocol Type entries that are deleted from the Address Translation (AR) table.
I32 rcTblArVlanByIpSubnetAdded	1.3.6.1.4.1.2272.1.7.25	Integer32	read-only	Used to indicate the number of VLAN by Ip entries that are added to the Address Translation (AR) table.
I32 rcTblArVlanByIpSubnetDeleted	1.3.6.1.4.1.2272.1.7.26	Integer32	read-only	Used to indicate the number of VLAN by Ip entries that are deleted from the Address Translation (AR) table.
I32 rcTblArIpSubnetsAdded	1.3.6.1.4.1.2272.1.7.27	Integer32	read-only	Used to indicate the number of Ip subnet entries that are added to the Address Translation (AR) table.
I32 rcTblArIpSubnetsDeleted	1.3.6.1.4.1.2272.1.7.28	Integer32	read-only	Used to indicate the number of Ip subnet entries that are deleted from the Address Translation (AR) table.
I32 rcTblArRsvpsAdded	1.3.6.1.4.1.2272.1.7.29	Integer32	read-only	Used to indicate the number of RSVP entries that are added to the Address Translation (AR) table.
I32 rcTblArRsvpsDeleted	1.3.6.1.4.1.2272.1.7.30	Integer32	read-only	Used to indicate the number of RSVP entries that are deleted from the Address Translation (AR) table.
I32 rcTblBrdgFdbSize	1.3.6.1.4.1.2272.1.7.31	Integer32	read-only	Used to indicate the number of entries in the dot1d forwarding database table.
I32 rcTblBrdgStaticSize	1.3.6.1.4.1.2272.1.7.32	Integer32	read-only	Used to indicate the number of entries in the dot1d Static Address Filtering table.
I32 rcTblIpAddrSize	1.3.6.1.4.1.2272.1.7.33	Integer32	read-only	Used to indicate the number of entries in the IP Address table.
I32 rcTblIpForwardingSize	1.3.6.1.4.1.2272.1.7.34	Integer32	read-only	Used to indicate the number of entries in the IP Forwarding/Best Route table.
I32 rcTblIpNetToMediaSize	1.3.6.1.4.1.2272.1.7.35	Integer32	read-only	Used to indicate the number of entries in the IP Net-to-media table.
I32 rcTblIpBestPlusAltRouteSize	1.3.6.1.4.1.2272.1.7.36	Integer32	read-only
I32 rcTblIpBestPathSize	1.3.6.1.4.1.2272.1.7.37	Integer32	read-only
I32 rcTblIpBestPlusAltPathSize	1.3.6.1.4.1.2272.1.7.38	Integer32	read-only
rcIp	1.3.6.1.4.1.2272.1.8
rcIpConf	1.3.6.1.4.1.2272.1.8.1
rcIpConfTable	1.3.6.1.4.1.2272.1.8.1.1		not-accessible	A table used to maintain IP routing information for a particular interface.
rcIpConfEntry	1.3.6.1.4.1.2272.1.8.1.1.1		not-accessible	Entry containing IP routing information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.
NUM rcIpConfIfIndex	1.3.6.1.4.1.2272.1.8.1.1.1.1	InterfaceIndexOrZero	read-only	An unique value to identify a physical interface or a logical interface (VLAN).
T/F rcIpConfAdvertDefRte	1.3.6.1.4.1.2272.1.8.1.1.1.2	TruthValue	read-write	Used to indicate whether this interface should advertize a RIP default route.
T/F rcIpConfAcceptDefRte	1.3.6.1.4.1.2272.1.8.1.1.1.3	TruthValue	read-write	Used to indicate whether this interface should accept a RIP default route.
ROW rcIpConfRowStatus	1.3.6.1.4.1.2272.1.8.1.1.1.4	RowStatus	read-write	Row status for this entry.
T/F rcIpConfRipEnable	1.3.6.1.4.1.2272.1.8.1.1.1.5	TruthValue	read-write	Enable or disable RIP routing on the specified interface.
T/F rcIpConfOspfEnable	1.3.6.1.4.1.2272.1.8.1.1.1.6	TruthValue	read-write	Enable or disable OSPF routing on the specified interface.
T/F rcIpConfIgmpEnable	1.3.6.1.4.1.2272.1.8.1.1.1.7	TruthValue	read-write	Enable or disable IGMP on the specified interface.
T/F rcIpConfAddrAssigned	1.3.6.1.4.1.2272.1.8.1.1.1.8	TruthValue	read-only	Indicate whether IpAddress has been assigned for this interface.
T/F rcIpConfDhcpEnable	1.3.6.1.4.1.2272.1.8.1.1.1.9	TruthValue	read-write	Enable or disable DHCP on the specified interface.
T/F rcIpConfTriggeredUpdateEnable	1.3.6.1.4.1.2272.1.8.1.1.1.10	TruthValue	read-write	Used to indicate whether the RIP triggered update feature should be enabled on this interface.
T/F rcIpConfAutoAggrerateEnable	1.3.6.1.4.1.2272.1.8.1.1.1.11	TruthValue	read-write	Used to indicate whether the auto aggregation feature should be enabled on this interface.
T/F rcIpConfGenerateDefaultRoute	1.3.6.1.4.1.2272.1.8.1.1.1.12	TruthValue	read-write	Used to indicate whether to generate a default RIP route on this interface.
T/F rcIpConfAdvertiseWhenDown	1.3.6.1.4.1.2272.1.8.1.1.1.13	TruthValue	read-write	The value is used indicated whether vlan state change should be notified to layer 3 or not, provided the vlan is configured as routable interface. Also used for single routable ports, in that case the criteria for state is PortOperStatus. Vlan is considered as UP if atleast one member of the port based vlan has link up, or atleast one port member of the policy based has an entry in the MGID or atleast one static member of the policy based vlan has link up. Otherwise, vlan is considered as DOWN. If the value is 'true' then the interface state change will not be notified to layer 3. (i.e., it always stays up). If the value is 'false' then the vlan state change will be notified to layer 3 so that IP related status reflects routable interface state.
T/F rcIpConfDirectBroadcastEnable	1.3.6.1.4.1.2272.1.8.1.1.1.14	TruthValue	read-write	Used to indicate whether this interface should forward direct broadcast traffic
STR rcIpConfRipInPolicy	1.3.6.1.4.1.2272.1.8.1.1.1.15	DisplayString	read-write	Used to indicate whether this interface should advertize a RIP default route.
STR rcIpConfRipOutPolicy	1.3.6.1.4.1.2272.1.8.1.1.1.16	DisplayString	read-write	Used to indicate whether this interface should accept a RIP default route.
INT rcIpConfOspfIfType	1.3.6.1.4.1.2272.1.8.1.1.1.17	INTEGER	read-write	OSPF Interface Type.
INT rcIpConfRipCost	1.3.6.1.4.1.2272.1.8.1.1.1.18	INTEGER	read-write	Used to indicate the rip cost for this interface.
INT rcIpConfRipHolddown	1.3.6.1.4.1.2272.1.8.1.1.1.19	INTEGER	read-write	Used to indicate the rip holddown timer for this interface
INT rcIpConfRipTimeout	1.3.6.1.4.1.2272.1.8.1.1.1.20	INTEGER	read-write	Used to indicate the rip timeout interval for this interface
T/F rcIpConfRsmltEnable	1.3.6.1.4.1.2272.1.8.1.1.1.21	TruthValue	read-write	Used to enable Route Smlt feature.
T/F rcIpConfReversePathCheckEnable	1.3.6.1.4.1.2272.1.8.1.1.1.22	TruthValue	read-write	Used to indicate whether this interface should perform Reverse Path Check
INT rcIpConfReversePathCheckMode	1.3.6.1.4.1.2272.1.8.1.1.1.23	INTEGER	read-write	Reverse Path Checking mode.
T/F rcIpConfIpVpnLiteEnable	1.3.6.1.4.1.2272.1.8.1.1.1.26	TruthValue	read-create	Enable or disable ipvpn-lite capability on the specified circuitless ip interface.
rcIpConfOspfTable	1.3.6.1.4.1.2272.1.8.1.2		not-accessible	A table used to maintain OSPF information for a particular interface.
rcIpConfOspfEntry	1.3.6.1.4.1.2272.1.8.1.2.1		not-accessible	Entry containing OSPF information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.
NUM rcIpConfOspfIfIndex	1.3.6.1.4.1.2272.1.8.1.2.1.1	InterfaceIndexOrZero	read-only	An unique value to identify a physical interface or a logical interface (VLAN).
INT rcIpConfOspfRtrPriority	1.3.6.1.4.1.2272.1.8.1.2.1.2	INTEGER	read-write	The priority of this interface. Used in multi- access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.
INT rcIpConfOspfMetric	1.3.6.1.4.1.2272.1.8.1.2.1.3	INTEGER	read-write	The metric for this type of service (TOS) on this interface. The default value of the TOS 0 Metric is (10^9 / ifSpeed). The value FFFF means 'no route via this TOS'. A value of 0 means the interface speed (rcIpConfOspfDefaultMetric) will be used as metric value, when the state of the interface is up.
STR rcIpConfOspfAuthKey	1.3.6.1.4.1.2272.1.8.1.2.1.4	DisplayString	read-write	The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfIfAuthKey always returns an Octet String of length zero.
ROW rcIpConfOspfRowStatus	1.3.6.1.4.1.2272.1.8.1.2.1.5	RowStatus	read-write	Row status for this entry.
INT rcIpConfOspfHelloInterval	1.3.6.1.4.1.2272.1.8.1.2.1.6	INTEGER	read-write	The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
INT rcIpConfOspfRtrDeadInterval	1.3.6.1.4.1.2272.1.8.1.2.1.7	INTEGER	read-write	The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
IP rcIpConfOspfIfAreaId	1.3.6.1.4.1.2272.1.8.1.2.1.8	IpAddress	read-write	A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
INT rcIpConfOspfAuthType	1.3.6.1.4.1.2272.1.8.1.2.1.9	INTEGER	read-write	The authentication type specified for an interface. Additional authentication types may be assigned locally.
INT rcIpConfOspfPollInterval	1.3.6.1.4.1.2272.1.8.1.2.1.10	INTEGER	read-write	OSPF NBMA Interface Poll Interval.
INT rcIpConfOspfIfMtuIgnore	1.3.6.1.4.1.2272.1.8.1.2.1.11	INTEGER	read-write	Mtu-ignore flag is for ignoring the mtu checking in ospf bdb
rcIpConfOspfDefaultMetric	1.3.6.1.4.1.2272.1.8.1.3
INT rcIpConfOspfDefaultMetric10MegPort	1.3.6.1.4.1.2272.1.8.1.3.1	INTEGER	read-write	Used to indicate the cost associated with 10Meg Interface(Port).
INT rcIpConfOspfDefaultMetric100MegPort	1.3.6.1.4.1.2272.1.8.1.3.2	INTEGER	read-write	Used to indicate the cost associated with 100Meg Interface(Port).
INT rcIpConfOspfDefaultMetric1000MegPort	1.3.6.1.4.1.2272.1.8.1.3.3	INTEGER	read-write	Used to indicate the cost associated with 1000Meg Interface(Port).
INT rcIpConfOspfDefaultMetric10000MegPort	1.3.6.1.4.1.2272.1.8.1.3.4	INTEGER	read-write	Used to indicate the cost associated with 10000Meg Interface(Port).
rcIpConfOspf	1.3.6.1.4.1.2272.1.8.1.4
T/F rcIpConfOspfTrapEnable	1.3.6.1.4.1.2272.1.8.1.4.1	TruthValue	read-write	Used to indicate whether Ospf Traps should be sent.
T/F rcIpConfOspfAutoVirtLinkEnable	1.3.6.1.4.1.2272.1.8.1.4.2	TruthValue	read-write	Used to indicate whether auto virtual link creation is enabled or not. If set to true OSPF will create virtual links between ABRs whether it is needed or not, but adjacency will established only when one of the ABR losses connection to backbone area. If set to false then it is user resposibity to create virtual link whenever needed.
INT rcIpConfOspfSpfHoldDownTime	1.3.6.1.4.1.2272.1.8.1.4.3	INTEGER	read-write	The SPF Hold Down Timer value. The SPF will run at most once per hold down timer value.
INT rcIpConfOspfAction	1.3.6.1.4.1.2272.1.8.1.4.4	INTEGER	read-write
T/F rcIpConfOspfRfc1583Compatibility	1.3.6.1.4.1.2272.1.8.1.4.5	TruthValue	read-write	Controls the preference rules used when choosing among multiple AS-External-LSAs advertising the same destination. When this is enabled, the preference rule will be same as specified by RFC1583. When disabled, the new preference rule as described in RFC2328 will be applicable, which potentially prevents the routing loops when AS-External-LSAs for the same destination have been originated from different areas.
rcIpConfGlobal	1.3.6.1.4.1.2272.1.8.1.6
INT rcIpConfGlobalRipHoldDownTime	1.3.6.1.4.1.2272.1.8.1.6.1	INTEGER	read-write	Used to set the system-wide RIP hold down time in seconds.
T/F rcIpConfGlobalIcmpNetUnreach	1.3.6.1.4.1.2272.1.8.1.6.2	TruthValue	read-write	Used to set the icmp net unreach feature enable/disable.
T/F rcIpConfGlobalEcmpEnable	1.3.6.1.4.1.2272.1.8.1.6.3	TruthValue	read-write	Used to set the ecmp enable/disable.
INT rcIpConfGlobalEcmpMaxPath	1.3.6.1.4.1.2272.1.8.1.6.4	INTEGER	read-write	Used to globally configure maximum ECMP paths number.
T/F rcIpConfGlobalAlternativeEnable	1.3.6.1.4.1.2272.1.8.1.6.5	TruthValue	read-write	Used to globally configure alternative enable.
T/F rcIpConfGlobalRouteDiscoveryEnable	1.3.6.1.4.1.2272.1.8.1.6.6	TruthValue	read-write	Enable/disable ICMP Route Discovery feature
INT rcIpConfGlobalRipTimeOutInterval	1.3.6.1.4.1.2272.1.8.1.6.8	INTEGER	read-write	Rip TimeOut Interval in seconds
INT rcIpConfGlobalRipDefImportMetric	1.3.6.1.4.1.2272.1.8.1.6.9	INTEGER	read-write	Rip def import metric
STR rcIpConfGlobalEcmp1PathList	1.3.6.1.4.1.2272.1.8.1.6.10	DisplayString	read-write	Routes to networks specified in this prefix-list can have upto 1 ECMP path, irrespective of ecmp-max-path configuration
STR rcIpConfGlobalEcmp2PathList	1.3.6.1.4.1.2272.1.8.1.6.11	DisplayString	read-write	Routes to networks specified in this prefix-list can have upto 2 ECMP path, irrespective of ecmp-max-path configuration.
STR rcIpConfGlobalEcmp3PathList	1.3.6.1.4.1.2272.1.8.1.6.12	DisplayString	read-write	Routes to networks specified in this prefix-list can have upto 3 ECMP path, irrespective of ecmp-max-path configuration.
STR rcIpConfGlobalEcmp4PathList	1.3.6.1.4.1.2272.1.8.1.6.13	DisplayString	read-write	Routes to networks specified in this prefix-list can have upto 4 ECMP path, irrespective of ecmp-max-path configuration.
T/F rcIpConfGlobalEcmpPathListApply	1.3.6.1.4.1.2272.1.8.1.6.14	TruthValue	read-write	This is to apply any changes in ECMP path list configuration or in the prefix-lists configured to be used as path list
T/F rcIpConfGlobalIcmpRedirectMsg	1.3.6.1.4.1.2272.1.8.1.6.15	TruthValue	read-write
INT rcIpConfGlobalArpThreshold	1.3.6.1.4.1.2272.1.8.1.6.17	INTEGER	read-write	Defines the maximum number of outstanding arp request a switch can generate.
T/F rcIpConfGlobalAllowMoreSpecificNonLocalRouteEnable	1.3.6.1.4.1.2272.1.8.1.6.18	TruthValue	read-write	Used to determine whether more specific non local routes will go into the routing table.
T/F rcIpConfGlobalUdpCheckSumEnable	1.3.6.1.4.1.2272.1.8.1.6.19	TruthValue	read-write	Enable/disable UDP checksum calculation
T/F rcIpConfGlobalSuperNetEnable	1.3.6.1.4.1.2272.1.8.1.6.20	TruthValue	read-write	Used to globally enable Supernetting/ CIDR routing for IP
STR rcIpConfGlobalEcmp5PathList	1.3.6.1.4.1.2272.1.8.1.6.21	DisplayString	read-write	Routes to networks specified in this prefix-list can have upto 5 ECMP path, irrespective of ecmp-max-path configuration.
STR rcIpConfGlobalEcmp6PathList	1.3.6.1.4.1.2272.1.8.1.6.22	DisplayString	read-write	Routes to networks specified in this prefix-list can have upto 6 ECMP path, irrespective of ecmp-max-path configuration.
STR rcIpConfGlobalEcmp7PathList	1.3.6.1.4.1.2272.1.8.1.6.23	DisplayString	read-write	Routes to networks specified in this prefix-list can have upto 7 ECMP path, irrespective of ecmp-max-path configuration.
STR rcIpConfGlobalEcmp8PathList	1.3.6.1.4.1.2272.1.8.1.6.24	DisplayString	read-write	Routes to networks specified in this prefix-list can have upto 8 ECMP path, irrespective of ecmp-max-path configuration.
T/F rcIpConfGlobalArpMcastMacFlooding	1.3.6.1.4.1.2272.1.8.1.6.26	TruthValue	read-write	Enable/disable Ip Arp Multicast Mac Flooding feature.

internet

1.3.6.1

rapidCity

1.3.6.1.4.1.2272

Enterprise MIB for the Accelar product family.

rcMgmt

1.3.6.1.4.1.2272.1

rcSystem

1.3.6.1.4.1.2272.1.1

IP rcSysIpAddr

1.3.6.1.4.1.2272.1.1.1

IpAddress

read-only

This entity's IP address.

IP rcSysNetMask

1.3.6.1.4.1.2272.1.1.2

IpAddress

read-only

This entity's subnet mask.

IP rcSysBroadcast

1.3.6.1.4.1.2272.1.1.3

IpAddress

read-only

This entity's broadcast address.

STR rcSysVersion

1.3.6.1.4.1.2272.1.1.7

DisplayString

read-only

Software version running on device

INT rcSysResult

1.3.6.1.4.1.2272.1.1.9

INTEGER

read-only

Result from the last system action.

TIK rcSysLastChange

1.3.6.1.4.1.2272.1.1.10

TimeTicks

read-only

Last management initiated configuration change since sysUpTime.

TIK rcSysLastVlanChange

1.3.6.1.4.1.2272.1.1.11

TimeTicks

read-only

Last management initiated VLAN configuration change since sysUpTime.

TIK rcSysLastStatisticsReset

1.3.6.1.4.1.2272.1.1.12

TimeTicks

read-only

Last management initiated statistics reset since sysUpTime.

INT rcSysBufferUtil

1.3.6.1.4.1.2272.1.1.13

INTEGER

read-only

Buffer utilization as a percentage of the total amount of buffer space in the system. A high value indicates congestion.

INT rcSysBufferUtilPeak

1.3.6.1.4.1.2272.1.1.14

INTEGER

read-only

The largest buffer utilization since sysUpTime

TIK rcSysBufferUtilPeakTime

1.3.6.1.4.1.2272.1.1.15

TimeTicks

read-only

Timestamp for rcSysPeakBandwidth

G32 rcSysNVRamSize

1.3.6.1.4.1.2272.1.1.16

Gauge32

read-only

Total Non-volatile RAM in Kbytes

G32 rcSysNVRamUsed

1.3.6.1.4.1.2272.1.1.17

Gauge32

read-only

Non-volatile RAM in use in Kbytes

TIK rcSysLastSaveToNVRam

1.3.6.1.4.1.2272.1.1.18

TimeTicks

read-only

SysUpTime of the last time when NVRAM was written to. This could be a save of the system configuration or via a file transfer of a configuration file.

TIK rcSysLastSaveToStandbyNVRam

1.3.6.1.4.1.2272.1.1.19

TimeTicks

read-only

SysUpTime of the last time when the standby NVRAM (on the back-up CPU board) was written to.

G32 rcSysCpuUtil

1.3.6.1.4.1.2272.1.1.20

Gauge32

read-only

Percentage of CPU utilization. This object is not supported on VSP. VSP uses rcKhiSlotCpuCurrentUtil

INT rcSysRmonMemSize

1.3.6.1.4.1.2272.1.1.22

INTEGER

read-write

Amount of RAM in bytes to allocate for RMON to use when rcSysRmonEnable is TRUE.

T/F rcSysRmonEnable

1.3.6.1.4.1.2272.1.1.23

TruthValue

read-write

Control whether the RMON feature should be enabled. To enable the RMON feature, set this variable to true. The RMON agent in the device will get started immediately if the amount of memory specified by rcSysRmonMemSize is currently available in the device. To disable the RMON feature, set this variable to false, save the new setting to NVRAM, and reboot the device. After the device is rebooted the RMON agent will not be operational.

INT rcSysRmonTrapOption

1.3.6.1.4.1.2272.1.1.25

INTEGER

read-write

Used to indicate whether RMON traps should be sent to only the owner of the RMON alarm (i.e., the manager that created the alarm entry) or all trap recipients in the system trap receiver table.

T/F rcSysSupportRouting

1.3.6.1.4.1.2272.1.1.26

TruthValue

read-only

Used to indicate whether routing is supported in this product.

T/F rcSysSupportWebServer

1.3.6.1.4.1.2272.1.1.27

TruthValue

read-only

Used to indicate whether WebServer is supported in this product.

TIK rcSysLastIpAddrChange

1.3.6.1.4.1.2272.1.1.28

TimeTicks

read-only

Last management initiated IP address change since sysUpTime. Any addition or deletion of an IP address to a single routable port or a VLAN is time-stamped by this variable.

T/F rcSysAccessPolicyEnable

1.3.6.1.4.1.2272.1.1.31

TruthValue

read-write

Used to configure the system access policy feature. if 'true', the rcSysAccessPolicyTable is examined to determine which packets should be allowed or denied access to this device.

STR rcSysDefaultRuntimeConfigFileName

1.3.6.1.4.1.2272.1.1.32

DisplayString

read-only

default config.

STR rcSysDefaultBootConfigFileName

1.3.6.1.4.1.2272.1.1.33

DisplayString

read-only

default boot config.

STR rcSysConfigFileName

1.3.6.1.4.1.2272.1.1.34

DisplayString

read-write

File name used in conjunction with rcSysAction. If rcSysAction is set to 'saveRuntimeConfig' or 'saveRuntimeConfigToSlave' then this file name will be used instead of the file name specified in rcSysDefaultRuntimeConfigFileName. If rcSysAction is set to 'saveBootConfig' or 'saveBootConfigToSlave' then this file name will be used insteaad of the file name specified in rcSysDefaultBootConfigFileName. If the file name is blank (i.e., nothing is entered) then the default file name will be used.

TIK rcSysLastRunTimeConfigSave

1.3.6.1.4.1.2272.1.1.35

TimeTicks

read-only

SysUpTime of the last time when the run time configuration was written to.

TIK rcSysLastRunTimeConfigSaveToSlave

1.3.6.1.4.1.2272.1.1.36

TimeTicks

read-only

SysUpTime of the last time when the run time configuration was written to slave NVRAM.

TIK rcSysLastBootConfigSave

1.3.6.1.4.1.2272.1.1.37

TimeTicks

read-only

SysUpTime of the last time when the boot configuration was written to.

TIK rcSysLastBootConfigSaveOnSlave

1.3.6.1.4.1.2272.1.1.38

TimeTicks

read-only

SysUpTime of the last time when the boot configuration was written on the slave NVRAM.

INT rcSysRmonUtilizationMethod

1.3.6.1.4.1.2272.1.1.39

INTEGER

read-write

Used to control whether RMON should use a half-duplex or full-duplex formula to calculate port utilization. When set to 'halfDuplex', RMON will use InOctets and the port's speed to calculate port utilization (this is the standard RMON rfc1271 convention). When set to 'fullDuplex', RMON will use InOctets and OutOctets and 2X the port's speed to calculate port utilization. Furthermore, if this variable is set to 'fullDuplex', but the port is operating in a half-duplex mode, the calculation defaults back to the rfc1271 convention.

G32 rcSysOtherBufferUtil

1.3.6.1.4.1.2272.1.1.41

Gauge32

read-only

bw currently consumed

G32 rcSysOtherBufferUtilPeak

1.3.6.1.4.1.2272.1.1.42

Gauge32

read-only

peak bw since reset

TIK rcSysOtherBufferUtilPeakTime

1.3.6.1.4.1.2272.1.1.43

TimeTicks

read-only

timestamp for rcSysPeakBw

G32 rcSysOtherCpuUtil

1.3.6.1.4.1.2272.1.1.44

Gauge32

read-only

% cpu utilization

I32 rcSysDramSize

1.3.6.1.4.1.2272.1.1.46

Integer32

read-only

Dram size in mega-bytes

G32 rcSysDramUsed

1.3.6.1.4.1.2272.1.1.47

Gauge32

read-only

Dram used in percentage

I32 rcSysDramFree

1.3.6.1.4.1.2272.1.1.48

Integer32

read-only

Dram free size in kilo-bytes

I32 rcSysDramMaxBlockFree

1.3.6.1.4.1.2272.1.1.49

Integer32

read-only

Dram max block free size in kilo-bytes

IP rcSysVirtualIpAddr

1.3.6.1.4.1.2272.1.1.51

IpAddress

read-write

Virtual IP is an IP address that owned and advertised only by the master CPU. So whichever CPU is master registers this IP address. Unlike the management IP address, this address goes in the switch config file and not the boot config

IP rcSysVirtualNetMask

1.3.6.1.4.1.2272.1.1.52

IpAddress

read-write

Net mask of the management virtual Ip address

I32 rcSysReadWriteLevel

1.3.6.1.4.1.2272.1.1.53

Integer32

read-write

The status of the read/write level

INT rcSysMTUSize

1.3.6.1.4.1.2272.1.1.55

INTEGER

read-write

This is the maximum transmission size of frames that all the ports on the chassis support.

T/F rcSysForceTrapSender

1.3.6.1.4.1.2272.1.1.57

TruthValue

read-write

This is a flag that if user wants to configured CLIP (Circuit Less IP) as trap originator.

T/F rcSysMrouteStrLimit

1.3.6.1.4.1.2272.1.1.58

TruthValue

read-write

enable or disable mroute stream limit in system.

rcSysAccessPolicyTable

1.3.6.1.4.1.2272.1.1.61

not-accessible

Management access policy table. This table is used to permit or deny access to this device via the specified source Id.

rcSysAccessPolicyEntry

1.3.6.1.4.1.2272.1.1.61.1

not-accessible

An access policy table entry.

INT rcSysAccessPolicyId

1.3.6.1.4.1.2272.1.1.61.1.1

INTEGER

read-only

Policy Id.

STR rcSysAccessPolicyName

1.3.6.1.4.1.2272.1.1.61.1.2

DisplayString

read-write

Name of this policy.

T/F rcSysAccessPolicyPolicyEnable

1.3.6.1.4.1.2272.1.1.61.1.3

TruthValue

read-write

Indicate whether this policy is currently active.

INT rcSysAccessPolicyMode

1.3.6.1.4.1.2272.1.1.61.1.4

INTEGER

read-write

Used to indicate whether a packet having a source IP address that matches this entry should be permitted to enter the device or denied access.

INT rcSysAccessPolicyService

1.3.6.1.4.1.2272.1.1.61.1.5

INTEGER

read-write

Is represented as bitset to indicate which protocol this entry should be applied to. Value is one of multiple(logical 'OR') of the following values: telnet(1), snmp(2), tftp(4), ftp(8), http(16), rlogin(32), ssh(64), snmp-v3(128) telnet(1): enables telnet service snmp(2): enables snmp service tftp(4): enables tftp service ftp(8): enables ftp service http(16): enables http service rlogin(32): enables rlogin service ssh(64): enables ssh service snmp-v3(128): enables snmp service for v3 groups Value 0 means no service enabled.

INT rcSysAccessPolicyPrecedence

1.3.6.1.4.1.2272.1.1.61.1.6

INTEGER

read-write

Used to indicate the precedence of this policy. The Lower the number the higher the precedence.

STR rcSysAccessPolicyTrustedHostUserName

1.3.6.1.4.1.2272.1.1.61.1.10

DisplayString

read-write

User name on the trusted host performing a rlogin into the device.

INT rcSysAccessPolicyAccessLevel

1.3.6.1.4.1.2272.1.1.61.1.11

INTEGER

read-write

Access level of trusted host.

T/F rcSysAccessPolicyLog

1.3.6.1.4.1.2272.1.1.61.1.12

TruthValue

read-write

Used to indicate whether logging should be performed if this policy was applied.

C32 rcSysAccessPolicyUsage

1.3.6.1.4.1.2272.1.1.61.1.13

Counter32

read-only

Usage Counter

ROW rcSysAccessPolicyRowStatus

1.3.6.1.4.1.2272.1.1.61.1.14

RowStatus

read-write

Used to create/delete an entry

T/F rcSysAccessPolicyAccessStrict

1.3.6.1.4.1.2272.1.1.61.1.15

TruthValue

read-write

Used to restrict the access level specified in the system access policy table to exactly the same access level as specified by user. If TRUE then only the access level in the policy table is allowed access. If FALSE, then the default behavior is to assume the access level specified in policy table as the floor.

INT rcSysAccessPolicyNetInetAddrType

1.3.6.1.4.1.2272.1.1.61.1.16

INTEGER

read-write

Source network Inet Address Type.

IP rcSysAccessPolicyNetInetAddress

1.3.6.1.4.1.2272.1.1.61.1.17

InetAddress

read-write

Source network Inet Address (prefix/network).

ADR rcSysAccessPolicyNetInetAddrPrefixLen

1.3.6.1.4.1.2272.1.1.61.1.18

InetAddressPrefixLength

read-write

Source network Inet Address Prefix-Length/Mask.

IP rcSysAccessPolicyTrustedHostInetAddress

1.3.6.1.4.1.2272.1.1.61.1.19

InetAddress

read-write

Trusted Inet address of host performing a rlogin into the device.

rcSysTrapSenderTable

1.3.6.1.4.1.2272.1.1.62

not-accessible

The trap sender table (0 to 25 entries). This table lists the addresses of Network Management Stations and the Source Address that should receive trap messages from this entity when an exception condition occurs.

rcSysTrapSenderEntry

1.3.6.1.4.1.2272.1.1.62.1

not-accessible

A trap sender table entry.

IP rcSysTrapSenderRecvAddress

1.3.6.1.4.1.2272.1.1.62.1.1

IpAddress

read-only

IP address for trap receiver.

IP rcSysTrapSenderSrcAddress

1.3.6.1.4.1.2272.1.1.62.1.2

IpAddress

read-write

IP address for trap sender.

rcSysDnsServerListTable

1.3.6.1.4.1.2272.1.1.64

not-accessible

DNS serever list table used to store the details of the DNS server configured.

rcSysDnsServerListEntry

1.3.6.1.4.1.2272.1.1.64.1

not-accessible

table entry.

INT rcSysDnsServerListType

1.3.6.1.4.1.2272.1.1.64.1.1

INTEGER

read-only

Type of the DNS server

INT rcSysDnsServerListStatus

1.3.6.1.4.1.2272.1.1.64.1.3

INTEGER

read-only

Status of DNS server

C32 rcSysDnsServerListRequestCount

1.3.6.1.4.1.2272.1.1.64.1.4

Counter32

read-only

Number of request send to this server

C32 rcSysDnsServerListSuccessCount

1.3.6.1.4.1.2272.1.1.64.1.5

Counter32

read-only

Number of request send to this server which are successful

ROW rcSysDnsServerListRowStatus

1.3.6.1.4.1.2272.1.1.64.1.6

RowStatus

read-write

Used to create/delete DNS server entries in rcSysDnsServerListTable.

IPt rcSysDnsServerListAddressType

1.3.6.1.4.1.2272.1.1.64.1.7

InetAddressType

read-write

The address type of DNS Server.

IP rcSysDnsServerListAddress

1.3.6.1.4.1.2272.1.1.64.1.8

InetAddress

read-write

The address of the DNS Server

rcSysDnsHostTable

1.3.6.1.4.1.2272.1.1.65

not-accessible

DNS Host table.

rcSysDnsHostEntry

1.3.6.1.4.1.2272.1.1.65.1

not-accessible

table entry.

OCT rcSysDnsHostData

1.3.6.1.4.1.2272.1.1.65.1.1

OCTET STRING

read-only

Host Name or Host IP Address.

OCT rcSysDnsHostName

1.3.6.1.4.1.2272.1.1.65.1.2

OCTET STRING

read-only

Host Name.

OCT rcSysDnsHostSource

1.3.6.1.4.1.2272.1.1.65.1.4

OCTET STRING

read-only

DNS Server IP or /etc/host file.

IPt rcSysDnsHostAddressType

1.3.6.1.4.1.2272.1.1.65.1.5

InetAddressType

read-only

Address Type of the Host.

IP rcSysDnsHostAddress

1.3.6.1.4.1.2272.1.1.65.1.6

InetAddress

read-only

Address of the Host.

INT rcSysMsgLogFrequency

1.3.6.1.4.1.2272.1.1.66

INTEGER

read-only

Used to specify the maximum frequency/count of the occurence of the Log Message.

STR rcSysMsgLogText

1.3.6.1.4.1.2272.1.1.67

DisplayString

read-only

A textual string containing the first four characters of the Log Message.

T/F rcSysForceIpHdrSender

1.3.6.1.4.1.2272.1.1.68

TruthValue

read-write

Flag to decide if IP header source address will be matched with SNMP header sender networks.

STR rcSysDnsDomainName

1.3.6.1.4.1.2272.1.1.70

DisplayString

read-write

Default domain used for querying the DNS Server.

IP rcSysDnsServerListIpAddr

1.3.6.1.4.1.2272.1.1.71

IpAddress

read-only

DNS server's IP address

INT rcSysDnsRequestType

1.3.6.1.4.1.2272.1.1.72

INTEGER

read-only

DNS Type: Whether it was Dns Request or a Response

INT rcSysSpanningTreeOperMode

1.3.6.1.4.1.2272.1.1.73

INTEGER

read-only

This object indicates the current spanning-tree mode of the system. The meaning of specific values is: nortelStpg(1) .. The older proprietary mode which supports multiple spanning tree groups. pvst(2) ..Emulation of C***O spanning tree mode rstp(3) ..IEEE 802.1w mode mstp(4) ..IEEE 802.1s mode .

INT rcSysSpanningTreeAdminMode

1.3.6.1.4.1.2272.1.1.74

INTEGER

read-write

This object indicates the desired spanning-tree mode of the system. The meaning of specific values is: nortelStpg(1) .. The older proprietary mode which supports multiple spanning tree groups. pvst(2) ..Emulation of C***O spanning tree mode rstp(3) ..IEEE 802.1w mode mstp(4) ..IEEE 802.1s mode . Note that depending on the current value of rcSysSpanningTreeOperMode and the value to which this object is set, the operational mode may be immediately changed, or the change may not take effect until the next system reboot.

INT rcSysAutoRecoverDelay

1.3.6.1.4.1.2272.1.1.75

INTEGER

read-write

Time interval in seconds after which auto-recovery runs on ports to clear action taken by cp-limit, link flap or loop detect

INT rcSysMacFlapLimitTime

1.3.6.1.4.1.2272.1.1.76

INTEGER

read-write

Time limit in milliseconds for MAC flapping for loop-detect feature

I32 rcSysMacFlapLimitCount

1.3.6.1.4.1.2272.1.1.77

Integer32

read-only

Number of times mac flapping can happen for loop-detect feature

T/F rcSysExtCplimitEnable

1.3.6.1.4.1.2272.1.1.78

TruthValue

read-write

enable or disable extended CP-LIMIT in system.

INT rcSysExtCplimitMinCongTime

1.3.6.1.4.1.2272.1.1.79

INTEGER

read-write

Minimum time for which System octapid should be congested to trigger congestion algorithm for extended CP-LIMIT in mSecs

INT rcSysExtCplimitMaxPorts

1.3.6.1.4.1.2272.1.1.80

INTEGER

read-write

Maximum number of ports which need to be monitored for congestion in Extended CP-LIMIT

INT rcSysExtCplimitPortCongTime

1.3.6.1.4.1.2272.1.1.81

INTEGER

read-write

Minimum time for which ingress traffic utilization rate of a monitored port should stay more than the allowed limits in order to disable the port for extended CP-LIMIT in Secs

INT rcSysExtCplimitTrapLevel

1.3.6.1.4.1.2272.1.1.82

INTEGER

read-write

Indicates the trap level for extended CP-LIMIT

T/F rcSysExtCplimitSysOctapidCongested

1.3.6.1.4.1.2272.1.1.83

TruthValue

read-only

Indicates whether system octapid congestion detected for extended cp-limit

T/F rcSysExtCplimitPortsMonitored

1.3.6.1.4.1.2272.1.1.84

TruthValue

read-only

Indicates whether ports has been shutdown due to extended cp-limit

T/F rcSysExtCplimitPortsShutDown

1.3.6.1.4.1.2272.1.1.85

TruthValue

read-only

Indicates whether ports has been shutdown due to extended Cp-limit

INT rcSysActionL1

1.3.6.1.4.1.2272.1.1.86

INTEGER

read-write

Initiate a system action for layer1 user

INT rcSysActionL2

1.3.6.1.4.1.2272.1.1.87

INTEGER

read-write

Initiate a system action for layer2 user

INT rcSysActionL3

1.3.6.1.4.1.2272.1.1.88

INTEGER

read-write

Initiate a system action for layer3 user

INT rcSysActionRwa

1.3.6.1.4.1.2272.1.1.89

INTEGER

read-write

Initiate a system action.

I32 rcSysPowerUsage

1.3.6.1.4.1.2272.1.1.90

Integer32

read-only

The current power usage for the whole chassis.

I32 rcSysPowerAvailable

1.3.6.1.4.1.2272.1.1.91

Integer32

read-only

The current power available for the whole chassis.

rcSysFrcMsgControlTable

1.3.6.1.4.1.2272.1.1.94

not-accessible

Management Force-msg Control table. This table is used to specify the pattern for Force-msg Control

rcSysFrcMsgControlEntry

1.3.6.1.4.1.2272.1.1.94.1

not-accessible

A Force-msg Control table entry.

I32 rcSysFrcMsgControlPatternId

1.3.6.1.4.1.2272.1.1.94.1.1

Integer32

not-accessible

Pattern Id.

STR rcSysFrcMsgControlPattern

1.3.6.1.4.1.2272.1.1.94.1.2

DisplayString

read-write

Pattern for filtering the force-msg for msg control

ROW rcSysFrcMsgControlRowStatus

1.3.6.1.4.1.2272.1.1.94.1.3

RowStatus

read-write

Used to create/delete an entry

rcSysAccPolSnmpGrpTable

1.3.6.1.4.1.2272.1.1.95

not-accessible

SNMP group list for access policy

rcSysAccPolSnmpGrpEntry

1.3.6.1.4.1.2272.1.1.95.1

not-accessible

The table entry which covers the groups under snmp service.

STR rcSysAccPolSnmpGrpName

1.3.6.1.4.1.2272.1.1.95.1.1

SnmpAdminString

not-accessible

The snmp-v3 group name

SNM rcSysAccPolSnmpGrpModel

1.3.6.1.4.1.2272.1.1.95.1.2

SnmpSecurityModel

not-accessible

The snmp model

ROW rcSysAccPolSnmpGrpRowStatus

1.3.6.1.4.1.2272.1.1.95.1.3

RowStatus

read-write

Row status

ADR rcSysVirtualIpv6Addr

1.3.6.1.4.1.2272.1.1.96

Ipv6Address

read-write

Virtual IP is an IP address that owned and advertised only by the master CPU. So whichever CPU is master registers this IP address.

INT rcSysVirtualIpv6PrefixLength

1.3.6.1.4.1.2272.1.1.97

INTEGER

read-write

The length of the virtual ipv6 addr prefix (in bits).

U32 rcSysLicenseTrialDaysLeft

1.3.6.1.4.1.2272.1.1.100

Unsigned32

read-only

This indicates days left before License Trial Period will expire.

I32 rcSysTotalPower

1.3.6.1.4.1.2272.1.1.116

Integer32

read-only

The total power for the whole chassis.

I32 rcSysRedundantPower

1.3.6.1.4.1.2272.1.1.117

Integer32

read-only

Used to indicate the redundant power on the chassis. The redundant power is per power supply unit

T/F rcSysAuthSuccessTrapEnable

1.3.6.1.4.1.2272.1.1.118

TruthValue

read-write

Used to enable/disable the trap send for authenticaion success trap rcnAuthenticationSuccess. It only allow to be set when snmpEnableAuthenTraps is enabled. I will be set to disable when snmpEnableAuthenTraps is disabled

T/F rcSysUdpSrcByVirtualIpEnable

1.3.6.1.4.1.2272.1.1.119

TruthValue

read-write

Used to enable/disable virtual ip as udp source.

rcTftp

1.3.6.1.4.1.2272.1.2

IP rcTftpHost

1.3.6.1.4.1.2272.1.2.1

IpAddress

read-write

Name of source/destination host for the TFTP transfer.

STR rcTftpFile

1.3.6.1.4.1.2272.1.2.2

DisplayString

read-write

Name of file for the TFTP transfer.

INT rcTftpAction

1.3.6.1.4.1.2272.1.2.3

INTEGER

read-write

The action for the TFTP transfer.

INT rcTftpResult

1.3.6.1.4.1.2272.1.2.4

INTEGER

read-only

Contains result of the last Tftp action request.

rcVlan

1.3.6.1.4.1.2272.1.3

INT rcVlanNumVlans

1.3.6.1.4.1.2272.1.3.1

INTEGER

read-only

The number of VLANs currently defined in the switch.

rcVlanTable

1.3.6.1.4.1.2272.1.3.2

not-accessible

A list of Virtual LAN entries. The number of entries is given by rcVlanNumVlans.

rcVlanEntry

1.3.6.1.4.1.2272.1.3.2.1

not-accessible

Entry containing configuration information for a particular Virtual LAN. The relationship between the various port sets in a VLAN Entry are : o The set of ports defined by PortMembers must be a subset of the set of ports in the underlying STG of the VLAN. o The bitwise AND of PortMembers and NotAllowToJoin must be the empty set. o The bitwise OR of PortMembers and NotAllowToJoin must be the set of ports in the underlying STG of the VLAN. o The set of ports defined by StaticMembers must be a subset of the set of ports defined by PortMembers. o The bitwise XOR of PortMembers and StaticMembers defines the set of dynamic (potential) members of the VLAN. o The set of ports defined by ActiveMembers must be a subset of the set of ports defined by PortMembers.

RCV rcVlanId

1.3.6.1.4.1.2272.1.3.2.1.1

RcVlanIdOrNone

read-only

A value that uniquely identifies the Virtual LAN associated with this entry. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag.

STR rcVlanName

1.3.6.1.4.1.2272.1.3.2.1.2

DisplayString

read-write

An administratively-assigned name for this VLAN.

INT rcVlanColor

1.3.6.1.4.1.2272.1.3.2.1.3

INTEGER

read-write

An administratively-assigned color code for this VLAN. The value of this object is used by the VLAN Manager GUI tool to select a color when it draws this VLAN on the screen.

NUM rcVlanIfIndex

1.3.6.1.4.1.2272.1.3.2.1.6

InterfaceIndex

read-only

When rcVlanRoutingEnable is set to true(1), this value indicates the 'logical' ifIndex assigned to this VLAN. Otherwise, this value is meaningless and should be set to zero.

INT rcVlanAction

1.3.6.1.4.1.2272.1.3.2.1.7

INTEGER

read-write

VLAN related actions.

INT rcVlanResult

1.3.6.1.4.1.2272.1.3.2.1.8

INTEGER

read-only

The result from the last VLAN action.

INT rcVlanStgId

1.3.6.1.4.1.2272.1.3.2.1.9

INTEGER

read-write

Indicates the Spanning Tree Group (STG) used by this VLAN to determine the state of its ports. If this VLAN is not associated with any STG, this value should be set to zero.

INT rcVlanType

1.3.6.1.4.1.2272.1.3.2.1.10

INTEGER

read-write

The type of VLAN, distinguished according to the policy used to define its port membership. VSP9000 does not support bySvlan(6) and ByIds(7).

POR rcVlanPortMembers

1.3.6.1.4.1.2272.1.3.2.1.11

PortSet

read-write

The set of ports that are members (static or dynamic) of this VLAN.

POR rcVlanActiveMembers

1.3.6.1.4.1.2272.1.3.2.1.12

PortSet

read-only

The set of ports that are currently active in this VLAN. Active ports include all static ports and any dynamic ports where the VLAN policy was met.

POR rcVlanStaticMembers

1.3.6.1.4.1.2272.1.3.2.1.13

PortSet

read-write

The set of ports that are static members of this VLAN. A static member of a VLAN is always active and is never aged out.

POR rcVlanNotAllowToJoin

1.3.6.1.4.1.2272.1.3.2.1.14

PortSet

read-write

The set of ports that are not allowed to become members of this VLAN.

INT rcVlanProtocolId

1.3.6.1.4.1.2272.1.3.2.1.15

INTEGER

read-write

The protocol identifier of this VLAN. This value is meaningful only if rcVlanType is equal to byProtocolId(3). For other VLAN types it should have the value none(0).

IP rcVlanSubnetAddr

1.3.6.1.4.1.2272.1.3.2.1.16

IpAddress

read-write

The IP subnet address of this VLAN. This value is meaningful only if rcVlanType is equal to byIpSubnet(2). For other VLAN types it should have the value 0.0.0.0.

IP rcVlanSubnetMask

1.3.6.1.4.1.2272.1.3.2.1.17

IpAddress

read-write

The IP subnet mask of this VLAN. This value is meaningful only if rcVlanType is equal to byIpSubnet(2). For other VLAN types it should have the value 0.0.0.0.

INT rcVlanAgingTime

1.3.6.1.4.1.2272.1.3.2.1.18

INTEGER

read-write

The timeout period (in seconds) used for aging out dynamic members of this VLAN. This field is only relevant for policy-based VLANs.

MAC rcVlanMacAddress

1.3.6.1.4.1.2272.1.3.2.1.19

MacAddress

read-only

The MAC address assigned to the virtual router interface of this VLAN. This field is meaningful only if rcVlanRoutingEnable is equal to true(1).

ROW rcVlanRowStatus

1.3.6.1.4.1.2272.1.3.2.1.20

RowStatus

read-write

Used to create/delete entries in the rcVlanTable.

I32 rcVlanUserDefinedPid

1.3.6.1.4.1.2272.1.3.2.1.26

Integer32

read-write

When rcVlanProtocolId is set to usrDefined(15) in a protocol-based VLAN, this field represents the 16-bit user defined protocol identifier.

I32 rcVlanProtocolIds

1.3.6.1.4.1.2272.1.3.2.1.28

Integer32

read-write

Bitfield of protocol ids.

INT rcVlanTosValue

1.3.6.1.4.1.2272.1.3.2.1.34

INTEGER

read-write

Tos value.

INT rcVlanEncap

1.3.6.1.4.1.2272.1.3.2.1.35

INTEGER

read-write

This is the encapsulation type for userdefined protocol based vlans. This is not meaningful for other types of vlan. The default value is null.

INT rcVlanFdbAging

1.3.6.1.4.1.2272.1.3.2.1.37

INTEGER

read-write

The timeout period (in seconds) used for aging out fdb entries of this VLAN.

POR rcVlanOspfPassivePortMember

1.3.6.1.4.1.2272.1.3.2.1.44

PortSet

read-write

The set of ports in the vlan that are designated as ospf passive

INT rcVlanNlbMode

1.3.6.1.4.1.2272.1.3.2.1.46

INTEGER

read-write

NLB mode set on a VLAN.

OID rcVlanVrfId

1.3.6.1.4.1.2272.1.3.2.1.48

VrfIdentifier

read-write

Indicates the Virtual Router to which the VLAN belongs

STR rcVlanVrfName

1.3.6.1.4.1.2272.1.3.2.1.49

DisplayString

read-only

The Name of the Virtual Router to which the VLAN belongs

STR rcVlanNodalMepList

1.3.6.1.4.1.2272.1.3.2.1.54

DisplayString

read-write

List of nodal Meps assigned to this vlan. A mep consists of Domain Name, Association name and Mep Id separated by '.'. Each meps is separated by ',': ..,..,... The maximum number of nodal Mep for each vlan is 8.

I32 rcVlanNumOfNodalMep

1.3.6.1.4.1.2272.1.3.2.1.55

Integer32

read-only

Number of nodal meps assigned to this vlan

STR rcVlanNodalMipLevelList

1.3.6.1.4.1.2272.1.3.2.1.56

DisplayString

read-write

List of nodal Mip levels assigned to this vlan that allows Mip functionality to be enabled on a per level per vlan basis. A mip level is represented by an integer ranging from 0 to 7. The mip levels are separated by ',': ,,... The maximum number of nodal Mip levels for each vlan is 8.

I32 rcVlanNumOfNodalMipLevel

1.3.6.1.4.1.2272.1.3.2.1.57

Integer32

read-only

Number of nodal mip levels assigned to this vlan that allows MIP functionality to be enabled on a per level per vlan basis.

I32 rcVlanPlsbIsid

1.3.6.1.4.1.2272.1.3.2.1.61

Integer32

read-write

Plsb i-sid number assigned to a C-vlan. Default 0 value indicates that no i-sid has been assinged.

rcVlanPortTable

1.3.6.1.4.1.2272.1.3.3

not-accessible

A table used to maintain VLAN port related information.

rcVlanPortEntry

1.3.6.1.4.1.2272.1.3.3.1

not-accessible

Entry containing VLAN information regarding a particular port.

I32 rcVlanPortIndex

1.3.6.1.4.1.2272.1.3.3.1.1

Integer32

read-only

An unique index used to identify a particular port in the system. This index is equal to the ifIndex of the port.

I32 rcVlanPortNumVlanIds

1.3.6.1.4.1.2272.1.3.3.1.2

Integer32

read-only

Used to indicate the number of VLAN IDs that are stored in the rcVlanPortVlanIds variable.

INT rcVlanPortType

1.3.6.1.4.1.2272.1.3.3.1.4

INTEGER

read-write

The type of port: access(1) or trunk(2).

T/F rcVlanPortDiscardTaggedFrames

1.3.6.1.4.1.2272.1.3.3.1.5

TruthValue

read-write

A flag used to determine how to process tagged frames received on this access port. When the flag is set, these frames are discarded by the forwarding process. When the flag is reset, these frames are processed normally. This field is meaningless when the port is not an access port and should be set to false(2).

T/F rcVlanPortDiscardUntaggedFrames

1.3.6.1.4.1.2272.1.3.3.1.6

TruthValue

read-write

A flag used to determine how to process untagged frames received on this trunk port. When the flag is set, these frames are discarded by the forwarding process. When the flag is reset, these frames are assigned to the VLAN specified by rcVlanPortDefaultVlanId. This field is meaningless when the port is not a trunk port and should be set to false(2).

INT rcVlanPortDefaultVlanId

1.3.6.1.4.1.2272.1.3.3.1.7

INTEGER

read-write

The VLAN ID assigned to untagged frames received on this trunk port. This field is meaningless when the port is not a trunk port.

T/F rcVlanPortPerformTagging

1.3.6.1.4.1.2272.1.3.3.1.8

TruthValue

read-write

Enable/disable the port on the current vlan to perform tagging on the incoming and outgoing traffic.

T/F rcVlanPortLoopDetect

1.3.6.1.4.1.2272.1.3.3.1.10

TruthValue

read-write

Enable/disable loop detection on this port

NUM rcVlanPortFirstPortInOpid

1.3.6.1.4.1.2272.1.3.3.1.11

InterfaceIndex

read-only

This value gives the IfIndex of the first port in the octapid. This value is used to generate an error message when changing port type from normal to uni/nni and viceversa

NUM rcVlanPortLastPortInOpid

1.3.6.1.4.1.2272.1.3.3.1.12

InterfaceIndex

read-only

This value gives the IfIndex of the first port in the octapid. This value is used to generate an error message when changing port type from normal to uni/nni and viceversa

T/F rcVlanPortUntagDefaultVlan

1.3.6.1.4.1.2272.1.3.3.1.13

TruthValue

read-write

enable/disable Egress Tagging on the Default Vlan of the port.

INT rcVlanPortLoopDetectAction

1.3.6.1.4.1.2272.1.3.3.1.14

INTEGER

read-write

This value is used to specify the action which needs to be taken once a loop is detected on a specific port. VlanBlock is not supported in VSP9000.

T/F rcVlanPortArpDetect

1.3.6.1.4.1.2272.1.3.3.1.15

TruthValue

read-write

Enable/disable Arp detection on this port

T/F rcVlanPortSpoofDetect

1.3.6.1.4.1.2272.1.3.3.1.16

TruthValue

read-write

Enable/disable spoof detection on this port

T/F rcVlanPortClassificationSubnet

1.3.6.1.4.1.2272.1.3.3.1.18

TruthValue

read-write

Enable/disable Subnet based Vlan packets on this port.

T/F rcVlanPortClassificationProtocol

1.3.6.1.4.1.2272.1.3.3.1.19

TruthValue

read-write

Enable/disable Protocol based Vlan packets on this port.

INT rcVlanPortClassificationPrec

1.3.6.1.4.1.2272.1.3.3.1.20

INTEGER

read-write

Sets the precedence for vlan classification. A value of 1 puts classification of packets to source mac vlans ahead of subnet based vlans. A value of 2 puts subnet based vlans ahead of source mac vlans. Classification to other types of vlans is unaffected as it occurs following source mac and subnet based vlans.

OCT rcVlanPortVlanIdList

1.3.6.1.4.1.2272.1.3.3.1.21

OCTET STRING

read-write

This bitfield is used to identify which VLANs this port is assigned to. Each VLAN ID is stored as a bit. The most-significant (left-most) bit represents Vlan Id 1.

T/F rcVlanPortClassificationSourceMac

1.3.6.1.4.1.2272.1.3.3.1.22

TruthValue

read-write

Enable/disable SourceMac based Vlan packets on this port.

rcVlanMacTable

1.3.6.1.4.1.2272.1.3.4

not-accessible

A table used to maintain MAC addresses assigned to a particular VLAN by MAC address.

rcVlanMacEntry

1.3.6.1.4.1.2272.1.3.4.1

not-accessible

Entry containing VLAN information regarding a particular port.

I32 rcVlanMacVlanId

1.3.6.1.4.1.2272.1.3.4.1.1

Integer32

read-only

An unique index used to identify a VLAN (by MAC address) in the system.

MAC rcVlanMacAddr

1.3.6.1.4.1.2272.1.3.4.1.2

MacAddress

read-only

An unique index used to identify a MAC address assigned to a particular VLAN.

ROW rcVlanMacRowStatus

1.3.6.1.4.1.2272.1.3.4.1.3

RowStatus

read-write

Row status for this entry.

I32 rcVlanIgmpSnoopNumGroups

1.3.6.1.4.1.2272.1.3.5

Integer32

read-only

The number of entries (rows) in the rcVlanIgmpSnoopTable.

rcVlanLoopDetectedTable

1.3.6.1.4.1.2272.1.3.10

not-accessible

A list of Vlans the port belongs to and the corresponding loop detected status.

rcVlanLoopDetectedEntry

1.3.6.1.4.1.2272.1.3.10.1

not-accessible

Loop-Detected Entry.

I32 rcVlanLoopDetectedPortIndex

1.3.6.1.4.1.2272.1.3.10.1.1

Integer32

read-only

Port Number.

I32 rcVlanLoopDetectedVlanId

1.3.6.1.4.1.2272.1.3.10.1.2

Integer32

read-only

Gives the VlanId to which the port belongs.

INT rcVlanLoopDetectedValue

1.3.6.1.4.1.2272.1.3.10.1.3

INTEGER

read-only

Gives the Loop Detected status of the port in a vlan.

rcVlanDsapSsapTable

1.3.6.1.4.1.2272.1.3.11

not-accessible

A table used to maintain DSAP/SSAP values assigned to a sna802dot2 or userdefined vlan.

rcVlanDsapSsapEntry

1.3.6.1.4.1.2272.1.3.11.1

not-accessible

An entry in the rcVlanDsapSsap table.

I32 rcVlanDsapSsapVlanId

1.3.6.1.4.1.2272.1.3.11.1.1

Integer32

not-accessible

A unique index to identify a vlan.

INT rcVlanDsapSsapPid

1.3.6.1.4.1.2272.1.3.11.1.2

INTEGER

not-accessible

Values of DSAP/SSAP assigned to a particular vlan.

ROW rcVlanDsapSsapRowStatus

1.3.6.1.4.1.2272.1.3.11.1.3

RowStatus

read-write

Row Status.

rcVlanNewLoopDetectedTable

1.3.6.1.4.1.2272.1.3.12

not-accessible

A list of Vlans the port belongs to and the corresponding loop detected status.

rcVlanNewLoopDetectedEntry

1.3.6.1.4.1.2272.1.3.12.1

not-accessible

Loop-Detected Entry.

NUM rcVlanNewLoopDetectedPortIndex

1.3.6.1.4.1.2272.1.3.12.1.1

InterfaceIndex

not-accessible

Port Number.

I32 rcVlanNewLoopDetectedVlanId

1.3.6.1.4.1.2272.1.3.12.1.2

Integer32

not-accessible

Gives the VlanId to which the port belongs.

MAC rcVlanNewLoopDetectedMac

1.3.6.1.4.1.2272.1.3.12.1.3

MacAddress

not-accessible

Mac address

INT rcVlanNewLoopDetectedAction

1.3.6.1.4.1.2272.1.3.12.1.4

INTEGER

read-only

This value is used to specify the action which needs to be taken once a loop is detected on a specific port.

T/F rcVlanNewLoopDetectedSmltRemote

1.3.6.1.4.1.2272.1.3.12.1.5

TruthValue

read-only

A MAC address indicate for remote learnt, either local or remote.

rcChassis

1.3.6.1.4.1.2272.1.4

INT rcChasType

1.3.6.1.4.1.2272.1.4.1

INTEGER

read-only

Chassis Type

STR rcChasSerialNumber

1.3.6.1.4.1.2272.1.4.2

DisplayString

read-only

Unique serial number for this chassis.

STR rcChasHardwareRevision

1.3.6.1.4.1.2272.1.4.3

DisplayString

read-only

Device hardware revision level

INT rcChasNumSlots

1.3.6.1.4.1.2272.1.4.4

INTEGER

read-only

The number of slots in the chassis available for plug-in cards.

INT rcChasNumPorts

1.3.6.1.4.1.2272.1.4.5

INTEGER

read-only

The total number of ports currently installed in the chassis.

rcChasFan

1.3.6.1.4.1.2272.1.4.7

rcChasFanZoneTable

1.3.6.1.4.1.2272.1.4.7.2

not-accessible

Table for the zones available on the chassis

rcChasFanZoneEntry

1.3.6.1.4.1.2272.1.4.7.2.1

not-accessible

Contains information regarding a zone unit

INT rcChasFanZoneType

1.3.6.1.4.1.2272.1.4.7.2.1.1

INTEGER

not-accessible

Type of the fan zone.

INT rcChasFanZoneMode

1.3.6.1.4.1.2272.1.4.7.2.1.2

INTEGER

read-only

Functional mode of the fan zone.

BIT rcChasFanZoneModeStatus

1.3.6.1.4.1.2272.1.4.7.2.1.3

Bits

read-only

Bit set indicates the alarm type(s)

I32 rcChasFanZoneAlarmTimer

1.3.6.1.4.1.2272.1.4.7.2.1.4

Integer32

read-only

Alarm timer indicates the remaining time before system checks and shutdown module when fan is in the alarm state. Zero means the fan i snot in an alarm state

G32 rcChasFanZoneTemperature

1.3.6.1.4.1.2272.1.4.7.2.1.5

Gauge32

read-only

Highest temperature measured in celsius degree from all the sensors (inlet and outlet) in the zone

INT rcChasFanZoneTray1LedColor

1.3.6.1.4.1.2272.1.4.7.2.1.6

INTEGER

read-only

Led color indicate fans operation status on tray off: Indicates no tray or power off. green: Indicates all fans are operational in a tray. red: Front Zone Tray: more than one fans in a tray are not opertional. Rear Zone Tray: one of two or both fans fans in a tray are not operational. amber: Front Zone Tray: one of eight fans is not operational. Rear Zone Tray: It is not applicable for Rear Zone tray

INT rcChasFanZoneTray2LedColor

1.3.6.1.4.1.2272.1.4.7.2.1.7

INTEGER

read-only

Led color indicate fans operation status on tray off: Indicates no tray or power off. green: Indicates all fans are operational in a tray. red: Front Zone Tray: more than one fans in a tray are not opertional. Rear Zone Tray: one of two fans or both fans in a tray are not operational. amber: Front Zone Tray: one of eight fans is not operational. Rear Zone Tray: It is not applicable for Rear Zone tray

rcChasFanInfoTable

1.3.6.1.4.1.2272.1.4.7.3

not-accessible

This table contains information for all the fans on the chassis

rcChasFanInfoEntry

1.3.6.1.4.1.2272.1.4.7.3.1

not-accessible

Contains information regarding a fan unit

INT rcChasFanInfoTray

1.3.6.1.4.1.2272.1.4.7.3.1.1

INTEGER

not-accessible

Number of trays per zone in chassis

INT rcChasFanInfoFan

1.3.6.1.4.1.2272.1.4.7.3.1.2

INTEGER

not-accessible

Number of fans per tray

INT rcChasFanInfoExpectedSpeed

1.3.6.1.4.1.2272.1.4.7.3.1.3

INTEGER

read-only

The administrative setting for the fan speed low: Low speed set by software medium: Medium speed set by software high: High speed set by software hardware: Speed controlled by hardware

INT rcChasFanInfoOperSpeed

1.3.6.1.4.1.2272.1.4.7.3.1.4

INTEGER

read-only

Actual speed of the fan

INT rcChasFanInfoStatus

1.3.6.1.4.1.2272.1.4.7.3.1.5

INTEGER

read-only

The operational status of the fan. Details below: ok(1): Fan operating under normal condition(s) faulty(2): Fan not operating as expected

rcChasPowerSupply

1.3.6.1.4.1.2272.1.4.8

rcChasPowerSupplyTable

1.3.6.1.4.1.2272.1.4.8.1

not-accessible

This table contains information about power supplies.

rcChasPowerSupplyEntry

1.3.6.1.4.1.2272.1.4.8.1.1

not-accessible

Contains information regarding a power supply unit.

INT rcChasPowerSupplyId

1.3.6.1.4.1.2272.1.4.8.1.1.1

INTEGER

read-only

The power supply Id.

INT rcChasPowerSupplyOperStatus

1.3.6.1.4.1.2272.1.4.8.1.1.2

INTEGER

read-only

Actual status of the power supply: - unknown(1) - status can not be determined. - empty(2) - power supply not installed. - up(3) - present and supplying power. - down(4) - present, but failure indicated.

rcChasPowerSupplyDetailTable

1.3.6.1.4.1.2272.1.4.8.2

not-accessible

This table contains detailed information about power supplies.

rcChasPowerSupplyDetailEntry

1.3.6.1.4.1.2272.1.4.8.2.1

not-accessible

Contains detailed info regarding a power supply unit.

INT rcChasPowerSupplyDetailId

1.3.6.1.4.1.2272.1.4.8.2.1.1

INTEGER

read-only

The power supply Id.

INT rcChasPowerSupplyDetailType

1.3.6.1.4.1.2272.1.4.8.2.1.2

INTEGER

read-only

The power supply type.

STR rcChasPowerSupplyDetailSerialNumber

1.3.6.1.4.1.2272.1.4.8.2.1.3

DisplayString

read-only

The power supply serial number.

STR rcChasPowerSupplyDetailHardwareRevision

1.3.6.1.4.1.2272.1.4.8.2.1.4

DisplayString

read-only

The hardware revision of the power supply.

STR rcChasPowerSupplyDetailPartNumber

1.3.6.1.4.1.2272.1.4.8.2.1.5

DisplayString

read-only

The power supply part number.

STR rcChasPowerSupplyDetailDescription

1.3.6.1.4.1.2272.1.4.8.2.1.6

DisplayString

read-only

The detail description of power supply.

INT rcChasPowerSupplyDetailInputLineVoltage

1.3.6.1.4.1.2272.1.4.8.2.1.8

INTEGER

read-only

The power supply Input Line voltage.

I32 rcChasPowerSupplyDetailOutputWatts

1.3.6.1.4.1.2272.1.4.8.2.1.10

Integer32

read-only

The output power of this power supply

rcCard

1.3.6.1.4.1.2272.1.4.9

rcCardTable

1.3.6.1.4.1.2272.1.4.9.1

not-accessible

A table that contains information about the cards in this chassis. For those slots that do not contain a physical card, the table may be implemented to contain a conceptual row with the type of physical module set to 'chasCardEmpty', or it may be implemented to have no conceptual row instance.

rcCardEntry

1.3.6.1.4.1.2272.1.4.9.1.1

not-accessible

Card attributes

INT rcCardIndex

1.3.6.1.4.1.2272.1.4.9.1.1.1

INTEGER

read-only

A unique value for each module within the chassis. This value is determined by the chassis slot number where the module is inserted. Valid entries are 1 to the value of rcChasNumSlots

INT rcCardType

1.3.6.1.4.1.2272.1.4.9.1.1.2

INTEGER

read-only

Used to indicate the card type. The value returned is defined by the description in rc2kCardTable.

STR rcCardOxateCpld

1.3.6.1.4.1.2272.1.4.9.1.1.9

DisplayString

read-only

Oxate CPLD version for CP card

STR rcCardOxideFpga

1.3.6.1.4.1.2272.1.4.9.1.1.10

DisplayString

read-only

Oxide FGPA version for CP card

STR rcCardCatskillFpga

1.3.6.1.4.1.2272.1.4.9.1.1.11

DisplayString

read-only

Catskill FPGA version for CP card

STR rcCardQE

1.3.6.1.4.1.2272.1.4.9.1.1.12

DisplayString

read-only

QE version for CP card

STR rcCardK2Fpga

1.3.6.1.4.1.2272.1.4.9.1.1.13

DisplayString

read-only

K2 FPGA version for IO card

STR rcCardIoDateDC

1.3.6.1.4.1.2272.1.4.9.1.1.14

DisplayString

read-only

IO Date DC CPLD for IO card

STR rcCardIoDateBB

1.3.6.1.4.1.2272.1.4.9.1.1.15

DisplayString

read-only

IO Date BaseBoard CPLD for IO card

STR rcCardIoPimCpld

1.3.6.1.4.1.2272.1.4.9.1.1.16

DisplayString

read-only

IO PIM CPLD for IO card

STR rcCardLed0Cpld

1.3.6.1.4.1.2272.1.4.9.1.1.17

DisplayString

read-only

LED0 CPLD for IO card

STR rcCardLed1Cpld

1.3.6.1.4.1.2272.1.4.9.1.1.18

DisplayString

read-only

LED1 CPLD for IO card

STR rcCardZagrosFpga

1.3.6.1.4.1.2272.1.4.9.1.1.19

DisplayString

read-only

Zagros FPGA for IO card

STR rcCardRsp

1.3.6.1.4.1.2272.1.4.9.1.1.20

DisplayString

read-only

RSP for IO card

STR rcCardBcmMac

1.3.6.1.4.1.2272.1.4.9.1.1.21

DisplayString

read-only

BCM Mac for IO card

STR rcCardPhosphideFpga

1.3.6.1.4.1.2272.1.4.9.1.1.22

DisplayString

read-only

Phosphide FPGA for IO card

STR rcCardSulfideFpga

1.3.6.1.4.1.2272.1.4.9.1.1.23

DisplayString

read-only

Sulfide FPGA for IO card

STR rcCardFluorateCpld

1.3.6.1.4.1.2272.1.4.9.1.1.24

DisplayString

read-only

Fluorate Cpld for SF card

STR rcCardBme

1.3.6.1.4.1.2272.1.4.9.1.1.25

DisplayString

read-only

BME for SF card

rcPort

1.3.6.1.4.1.2272.1.4.10

rcPortTable

1.3.6.1.4.1.2272.1.4.10.1

not-accessible

Port table

rcPortEntry

1.3.6.1.4.1.2272.1.4.10.1.1

not-accessible

Entry containing info. for a particular port

NUM rcPortIndex

1.3.6.1.4.1.2272.1.4.10.1.1.1

InterfaceIndex

read-only

An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.

INT rcPortType

1.3.6.1.4.1.2272.1.4.10.1.1.2

INTEGER

read-only

Port type

INT rcPortAction

1.3.6.1.4.1.2272.1.4.10.1.1.6

INTEGER

read-write

Port related actions.

INT rcPortResult

1.3.6.1.4.1.2272.1.4.10.1.1.7

INTEGER

read-only

Result from the last Vlan action.

T/F rcPortAutoNegotiate

1.3.6.1.4.1.2272.1.4.10.1.1.11

TruthValue

read-write

Indicate whether this port enabled for auto negotiations or not.

INT rcPortAdminDuplex

1.3.6.1.4.1.2272.1.4.10.1.1.12

INTEGER

read-write

Indicates the port duplex type

INT rcPortOperDuplex

1.3.6.1.4.1.2272.1.4.10.1.1.13

INTEGER

read-only

Indicate this port's current duplex value.

INT rcPortAdminSpeed

1.3.6.1.4.1.2272.1.4.10.1.1.14

INTEGER

read-write

Indicate this port's speed.

I32 rcPortOperSpeed

1.3.6.1.4.1.2272.1.4.10.1.1.15

Integer32

read-only

Indicate this port's current speed value.

I32 rcPortMltId

1.3.6.1.4.1.2272.1.4.10.1.1.16

Integer32

read-only

Indicate which multi-link trunk (MLT) this port is assigned to. If this port is not associated with any MLT, this value will be set to zero(0).

T/F rcPortLocked

1.3.6.1.4.1.2272.1.4.10.1.1.17

TruthValue

read-only

Indicate whether this port is locked.

T/F rcPortAutoNegotiationSupported

1.3.6.1.4.1.2272.1.4.10.1.1.18

TruthValue

read-only

Indicate whether this port can support auto-negotiation.

T/F rcPortSingleRoutablePort

1.3.6.1.4.1.2272.1.4.10.1.1.19

TruthValue

read-only

Indicate whether this port is a single routable port. If this value is true, the port functions like a traditional router port.

T/F rcPortUnknownMacDiscard

1.3.6.1.4.1.2272.1.4.10.1.1.20

TruthValue

read-write

If rcUnknownMacDiscard is set to True, then a packet with an unknown source MAC address is dropped on that port, and other ports then will discard any packets with this MAC address in the destination field. For example, suppose 11:22:33:44:55:66 is an unknown source MAC, packets with source MAC 11:22:33:44:55 coming from this port is discarded, further more, packets with destination MAC 11:22:33:44:55:66 coming from other ports are also discarded, unless this address is later learned on another port or the restriction ages out.

C32 rcPortNumStateTransition

1.3.6.1.4.1.2272.1.4.10.1.1.21

Counter32

read-only

# state transitions.

INT rcPortQosLevel

1.3.6.1.4.1.2272.1.4.10.1.1.30

INTEGER

read-write

Used to specify the Qos level packets, carried on this port, should be processed with.

T/F rcPortDiffServEnable

1.3.6.1.4.1.2272.1.4.10.1.1.31

TruthValue

read-write

Used to enable/disable the Differentiated Service feature on this port.

INT rcPortDiffServType

1.3.6.1.4.1.2272.1.4.10.1.1.32

INTEGER

read-write

Used to specify the Differentiated Service type for this port.

STR rcPortVendorDescr

1.3.6.1.4.1.2272.1.4.10.1.1.34

DisplayString

read-only

Used to show the name of the vendor of this port's connector. Only applicable to ports on a GBIC cards.

STR rcPortName

1.3.6.1.4.1.2272.1.4.10.1.1.35

DisplayString

read-write

This port's name.

ENA rcPortAdminRouting

1.3.6.1.4.1.2272.1.4.10.1.1.43

EnableValue

read-write

Indicate whether the port is routable.

ENA rcPortOperRouting

1.3.6.1.4.1.2272.1.4.10.1.1.44

EnableValue

read-only

The status of the port whether is routable.

T/F rcPortIeee8021POverrideEnable

1.3.6.1.4.1.2272.1.4.10.1.1.46

TruthValue

read-write

Used to enable/disable IEEE 802.1P override. If it is enabled, 802.1p value from a tagged frame may not be honored.

T/F rcPortHighSecureEnable

1.3.6.1.4.1.2272.1.4.10.1.1.51

TruthValue

read-write

Enable/Disable high secure feature.

INT rcPortMrouteStrLimit

1.3.6.1.4.1.2272.1.4.10.1.1.55

INTEGER

read-write

maximum number of multicast streams that are allowed to ingress to CPU through this port.

INT rcPortMrouteStrTimerCheck

1.3.6.1.4.1.2272.1.4.10.1.1.56

INTEGER

read-write

sampling period to check number of multicast streams that has ingressed CPU through this port in seconds.

T/F rcPortMrouteStrLimitEnable

1.3.6.1.4.1.2272.1.4.10.1.1.57

TruthValue

read-write

enable or disable mroute stream limit on port.

BIT rcPortAutoNegAd

1.3.6.1.4.1.2272.1.4.10.1.1.62

Bits

read-write

This object is used to specify the port speed and duplex abilities to be advertised during link negotiation. bit 0 - 10 half duplex advertised bit 1 - 10 full duplex advertised bit 2 - 100 half duplex advertised bit 3 - 100 full duplex advertised bit 5 - 1000 full duplex advertised bit 6 - Mac PAUSE frame support advertised bit 7 - Asymmetric PAUSE frame support advertised bit 8 - No advertisements The abilities specified in this object are only used when auto-negotiation is enabled on the port. If all bits in this object are disabled, and auto-negotiation is enabled on the port, then the physical link process on the port will be disabled (if hardware supports this ability). Any change in the value of this bit map will force the PHY to restart the auto-negotiation process. This will have the same effect as physically unplugging and reattaching the cable plant attached to this port. The capabilities being advertised are either all the capabilities supported by the hardware or the user- configured capabilities which is a subset of all the capability supported by hardware. The default value for this object will be all the capabilities supported by the hardware. Note that bit 6 and bit 7 are currently not supported in ERS8600.

T/F rcPortAutoRecoverPort

1.3.6.1.4.1.2272.1.4.10.1.1.64

TruthValue

read-write

enable or disable auto recovery of port from action taken by cp-limit, link flap or loop detect features

INT rcPortEgressRateLimit

1.3.6.1.4.1.2272.1.4.10.1.1.67

INTEGER

read-write

Egress Rate Limit. for VSP 9000, range is 10000 to 10000000

ENA rcPortEgressRateLimitState

1.3.6.1.4.1.2272.1.4.10.1.1.68

EnableValue

read-write

Used to enable/disable shape/egress-rate-limit functionality.

INT rcPortIngressRateLimit

1.3.6.1.4.1.2272.1.4.10.1.1.85

INTEGER

read-write

Limits the amount of traffic from this Ingress port.

IDL rcPortVrfIdList

1.3.6.1.4.1.2272.1.4.10.1.1.87

IdList

read-only

The set of VRF ids to which this port belongs.

OCT rcPortVrfNameList

1.3.6.1.4.1.2272.1.4.10.1.1.96

OCTET STRING

read-only

The set of VRF names to which this port belongs.

OID rcPortBrouterVrfId

1.3.6.1.4.1.2272.1.4.10.1.1.97

VrfIdentifier

read-write

Gives the VRF Id for this Brouter port.

STR rcPortBrouterVrfName

1.3.6.1.4.1.2272.1.4.10.1.1.98

DisplayString

read-only

Gives the VRF Name for this Brouter port.

C32 rcPortVrfCount

1.3.6.1.4.1.2272.1.4.10.1.1.99

Counter32

read-only

The total number of VRFs this port is associated to.

INT rcPortIngressRatePeak

1.3.6.1.4.1.2272.1.4.10.1.1.108

INTEGER

read-write

Peak rate limit for this port. 0 means disable

INT rcPortIngressRateSvc

1.3.6.1.4.1.2272.1.4.10.1.1.109

INTEGER

read-write

Service rate limit for this port. 0 mean deisable

INT rcPortCpLimitPktRate

1.3.6.1.4.1.2272.1.4.10.1.1.110

INTEGER

read-write

Used to limit Control packets on the port to qos-levels 6 and 7. Sets the limit in packets per second.

T/F rcPortCpLimitShutDownEnable

1.3.6.1.4.1.2272.1.4.10.1.1.111

TruthValue

read-write

Used to indicate if the port should be shutdown when the CpLimitPktRate is exceeded.

rcPortPcapTable

1.3.6.1.4.1.2272.1.4.10.2

not-accessible

Port pcap Table

rcPortPcapEntry

1.3.6.1.4.1.2272.1.4.10.2.1

not-accessible

Entry containing pcap info. for a particular port

NUM rcPortPcapIndex

1.3.6.1.4.1.2272.1.4.10.2.1.1

InterfaceIndex

read-only

An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.

T/F rcPortPcapEnable

1.3.6.1.4.1.2272.1.4.10.2.1.2

TruthValue

read-write

To enable pcap for the port

INT rcPortPcapMode

1.3.6.1.4.1.2272.1.4.10.2.1.3

INTEGER

read-write

Mode in which pcap is enabled

rcPortLacpTable

1.3.6.1.4.1.2272.1.4.10.4

not-accessible

Port LACP table

rcPortLacpEntry

1.3.6.1.4.1.2272.1.4.10.4.1

not-accessible

Entry containing info. for a particular port

T/F rcPortLacpAdminEnable

1.3.6.1.4.1.2272.1.4.10.4.1.1

TruthValue

read-write

Administratively enable/disable LACP on a port

T/F rcPortLacpOperEnable

1.3.6.1.4.1.2272.1.4.10.4.1.2

TruthValue

read-only

Indicates if LACP is operationally enabled or disabled on a port

INT rcPortLacpFastPeriodicTime

1.3.6.1.4.1.2272.1.4.10.4.1.3

INTEGER

read-write

The number of miliseconds between periodic transmissions using Short Timeouts.

INT rcPortLacpSlowPeriodicTime

1.3.6.1.4.1.2272.1.4.10.4.1.4

INTEGER

read-write

The number of miliseconds between periodic transmissions using LONG Timeouts.

INT rcPortLacpTimeoutScale

1.3.6.1.4.1.2272.1.4.10.4.1.5

INTEGER

read-write

Scalar value used to calculate timeout time from periodic time. Timeout = PeriodicTime * TimeoutScale

INT rcPortLacpAggrWaitTime

1.3.6.1.4.1.2272.1.4.10.4.1.6

INTEGER

read-write

The number of mili seconds to delay aggregation to allow multiple links to aggregate simultaneously.

INT rcPortLacpFastPeriodicTimeOper

1.3.6.1.4.1.2272.1.4.10.4.1.7

INTEGER

read-only

The operating value of fast periodic timer on the port.

INT rcPortLacpSlowPeriodicTimeOper

1.3.6.1.4.1.2272.1.4.10.4.1.8

INTEGER

read-only

The operating value of slow periodic timer on the port.

INT rcPortLacpTimeoutScaleOper

1.3.6.1.4.1.2272.1.4.10.4.1.9

INTEGER

read-only

The operating value of timeout scale on the port.

INT rcPortLacpAggrWaitTimeOper

1.3.6.1.4.1.2272.1.4.10.4.1.10

INTEGER

read-only

The operating value of aggreagate wait time on port.

rcPortVLacpTable

1.3.6.1.4.1.2272.1.4.10.5

not-accessible

Port Virtual LACP table

rcPortVLacpEntry

1.3.6.1.4.1.2272.1.4.10.5.1

not-accessible

Entry containing info. for a particular port

T/F rcPortVLacpAdminEnable

1.3.6.1.4.1.2272.1.4.10.5.1.1

TruthValue

read-write

Administratively enable/disable Virtual LACP on a port

T/F rcPortVLacpOperEnable

1.3.6.1.4.1.2272.1.4.10.5.1.2

TruthValue

read-only

Indicates if Virtual LACP is operationally enabled or disabled on a port

INT rcPortVLacpFastPeriodicTimer

1.3.6.1.4.1.2272.1.4.10.5.1.3

INTEGER

read-write

The number of miliseconds between periodic transmissions using Short Timeouts

INT rcPortVLacpSlowPeriodicTimer

1.3.6.1.4.1.2272.1.4.10.5.1.4

INTEGER

read-write

The number of miliseconds between periodic transmissions using LONG Timeouts.

INT rcPortVLacpTimeout

1.3.6.1.4.1.2272.1.4.10.5.1.5

INTEGER

read-write

Timeout control value. Long or Short Timeout

INT rcPortVLacpTimeoutScale

1.3.6.1.4.1.2272.1.4.10.5.1.6

INTEGER

read-write

Scalar value used to calculate timeout time from periodic time. Timeout = PeriodicTime * TimeoutScale

I32 rcPortVLacpEtherType

1.3.6.1.4.1.2272.1.4.10.5.1.7

Integer32

read-write

VLACP Protocol Identification. The id value is in Hex. Range in hex (0x600..0xffff)

MAC rcPortVLacpEtherMacAddress

1.3.6.1.4.1.2272.1.4.10.5.1.8

MacAddress

read-write

Multicast Mac Address exclusively used for VLACPDU's

INT rcPortVLacpPortState

1.3.6.1.4.1.2272.1.4.10.5.1.9

INTEGER

read-only

Display the Vlacp Port State.

rcPortRemoteMirroringTable

1.3.6.1.4.1.2272.1.4.10.6

not-accessible

Port Remote Mirroring Table

rcPortRemoteMirroringEntry

1.3.6.1.4.1.2272.1.4.10.6.1

not-accessible

Entry containing remote mirroring info. for a particular port

NUM rcPortRemoteMirroringIndex

1.3.6.1.4.1.2272.1.4.10.6.1.1

InterfaceIndex

read-only

An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.

T/F rcPortRemoteMirroringEnable

1.3.6.1.4.1.2272.1.4.10.6.1.2

TruthValue

read-write

To enable remote Mirroring for the port

INT rcPortRemoteMirroringMode

1.3.6.1.4.1.2272.1.4.10.6.1.3

INTEGER

read-write

Mode in which remote mirroring is enabled

MAC rcPortRemoteMirroringSrcMac

1.3.6.1.4.1.2272.1.4.10.6.1.4

MacAddress

read-write

Source Mac of the remote mirrored packet. Remote mirroring packet will be send with this source mac address

MAC rcPortRemoteMirroringDstMac

1.3.6.1.4.1.2272.1.4.10.6.1.5

MacAddress

read-write

Destination Mac of the remote mirrored packet. Packets will be bridged to this mac address. Remote mirroring packet will be send to this mac address

INT rcPortRemoteMirroringEtherType

1.3.6.1.4.1.2272.1.4.10.6.1.6

INTEGER

read-write

Ethertype of the remote mirrored packet. Packets will be send with this ethertype

INT rcPortRemoteMirroringVlanIdListSize

1.3.6.1.4.1.2272.1.4.10.6.1.7

INTEGER

read-only

Used to indicate the number of VLAN IDs that are assigned to this port.

OCT rcPortRemoteMirroringVlanIdList

1.3.6.1.4.1.2272.1.4.10.6.1.8

OCTET STRING

read-write

This field is used only if the port is assigned as remote mirroring termination port. Represents zero or more filter lists vlan in which the Destination Mac address resides. Each VLAN ID is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.

ROW rcPortRemoteMirroringRowStatus

1.3.6.1.4.1.2272.1.4.10.6.1.9

RowStatus

read-write

RowStatus

rcPortLosslessEnetTable

1.3.6.1.4.1.2272.1.4.10.13

not-accessible

Port Lossless Ethernet Table

rcPortLosslessEnetEntry

1.3.6.1.4.1.2272.1.4.10.13.1

not-accessible

Entry containing lossless Ethernet information for a particular port.

NUM rcPortLosslessEnetIndex

1.3.6.1.4.1.2272.1.4.10.13.1.1

InterfaceIndex

not-accessible

An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2. Lossless Ethernet will be limited to 10Gig ports.

T/F rcPortLosslessEnetConfigured

1.3.6.1.4.1.2272.1.4.10.13.1.2

TruthValue

read-write

To enable lossless mode for the port

INT rcPortLosslessEnetPauseType

1.3.6.1.4.1.2272.1.4.10.13.1.3

INTEGER

read-write

Pause frame type. fc - Pause, pfc - priority-based flow control.

I32 rcPortLosslessEnetPfcBandwidth

1.3.6.1.4.1.2272.1.4.10.13.1.4

Integer32

read-write

Guaranteed bandwidth in Gbps when rcPortLosslessEnetPauseType is set to pfc(2).

rcPortLock

1.3.6.1.4.1.2272.1.4.11

T/F rcPortLockEnable

1.3.6.1.4.1.2272.1.4.11.1

TruthValue

read-write

Indicate whether the port lock feature is enabled.

POR rcPortLockLockedPorts

1.3.6.1.4.1.2272.1.4.11.2

PortSet

read-write

The set of ports that are administratively locked. Locked ports cannot be modified in anyway until the port is unlocked first.

POR rcChasBrouterPorts

1.3.6.1.4.1.2272.1.4.17

PortSet

read-only

Used to indicate which ports in the system are configured as Brouter ports.

T/F rcChasFtpDaemonInSecondaryCpu

1.3.6.1.4.1.2272.1.4.26

TruthValue

read-write

Used to enable/disable FTP daemon in 2nd cpu.

T/F rcChasNewVlanOptmMode

1.3.6.1.4.1.2272.1.4.28

TruthValue

read-write

Vlan Optimization mode.

T/F rcChasVlanOptmMode

1.3.6.1.4.1.2272.1.4.29

TruthValue

read-only

Vlan Optimization mode the switch currently has booted and will remain the same until the next reboot.

T/F rcChasRspMode

1.3.6.1.4.1.2272.1.4.35

TruthValue

read-write

This configuration is for enabling/disabling 256K mode. The change will take effect upon reboot.

T/F rcChasRspOperMode

1.3.6.1.4.1.2272.1.4.36

TruthValue

read-only

R-mode the switch currently has booted and will remain the same until the next reboot.

INT rcChasRspModeError

1.3.6.1.4.1.2272.1.4.37

INTEGER

read-only

Used to indicate the r-mode error status

I32 rcChasNewMulticastResourceReservation

1.3.6.1.4.1.2272.1.4.44

Integer32

read-write

Used to reserve MGIDs for IP Multicast. The change will take effect upon reboot.

I32 rcChasMulticastResourceReservation

1.3.6.1.4.1.2272.1.4.45

Integer32

read-only

MGIDs the switch currently has reserved for IP Multicast; will remain the same until the next reboot.

ENA rcChasNewMaxVlanResourceReservation

1.3.6.1.4.1.2272.1.4.46

EnableValue

read-write

A mode where all MGIDs are reserved for VLAN use only; no IPMC. The change will take effect upon reboot.

ENA rcChasMaxVlanResourceReservation

1.3.6.1.4.1.2272.1.4.47

EnableValue

read-only

Tells if all MGIDs are reserved for VLAN use. Will remain the same until the next reboot.

I32 rcChasMgidUsageVlanCurrent

1.3.6.1.4.1.2272.1.4.48

Integer32

read-only

Number of MGIDs currently used for VLAN, including SMLT

I32 rcChasMgidUsageVlanRemaining

1.3.6.1.4.1.2272.1.4.49

Integer32

read-only

Number of MGIDs remaining allocated for VLAN

I32 rcChasMgidUsageMulticastCurrent

1.3.6.1.4.1.2272.1.4.50

Integer32

read-only

Number of MGIDs currently used for IPMC

I32 rcChasMgidUsageMulticastRemaining

1.3.6.1.4.1.2272.1.4.51

Integer32

read-only

Number of MGIDs remaining allocated for IPMC

T/F rcChasForceTopologyIpFlagEnable

1.3.6.1.4.1.2272.1.4.53

TruthValue

read-write

Used to enable/disable flag which is used to set the CLIP-ip as topology ip

I32 rcChasCircuitlessIpId

1.3.6.1.4.1.2272.1.4.54

Integer32

read-write

The Clip-Id set by the user to be used as Topology-ip. '0' means no circuitless IP id while '1..256' is valid circuitless Id

rcMirror

1.3.6.1.4.1.2272.1.5

rcDipSwitch

1.3.6.1.4.1.2272.1.6

rcTblSize

1.3.6.1.4.1.2272.1.7

I32 rcTblRmonStatSize

1.3.6.1.4.1.2272.1.7.1

Integer32

read-only

Used to indicate the current size of the RMON Statistic table.

I32 rcTblRmonHistoryControlSize

1.3.6.1.4.1.2272.1.7.2

Integer32

read-only

Used to indicate the current size of the RMON History Control table.

I32 rcTblRmonHistoryEnetSize

1.3.6.1.4.1.2272.1.7.3

Integer32

read-only

Used to indicate the current size of the RMON History Ethernet table.

I32 rcTblRmonAlarmSize

1.3.6.1.4.1.2272.1.7.4

Integer32

read-only

Used to indicate the current size of the RMON Alarm table.

I32 rcTblRmonEventSize

1.3.6.1.4.1.2272.1.7.5

Integer32

read-only

Used to indicate the current size of the RMON Event table.

I32 rcTblRmonLogSize

1.3.6.1.4.1.2272.1.7.6

Integer32

read-only

Used to indicate the current size of the RMON Log table.

I32 rcTblArTblSize

1.3.6.1.4.1.2272.1.7.7

Integer32

read-only

Used to indicate the size of the Address Translation (AR) table.

I32 rcTblArFree

1.3.6.1.4.1.2272.1.7.8

Integer32

read-only

Used to indicate the number of free entries that are available in the Address Translation (AR) table.

I32 rcTblArNoSpace

1.3.6.1.4.1.2272.1.7.9

Integer32

read-only

Used to indicate the number of entries that could not be added to the Address Translation (AR) table due to lack of space.

I32 rcTblArAdded

1.3.6.1.4.1.2272.1.7.10

Integer32

read-only

Used to indicate the number of entries added to the Address Translation (AR) table.

I32 rcTblArDeleted

1.3.6.1.4.1.2272.1.7.11

Integer32

read-only

Used to indicate the number of entries deleted to the Address Translation (AR) table.

I32 rcTblArMacAdded

1.3.6.1.4.1.2272.1.7.12

Integer32

read-only

Used to indicate the number of MAC entries added to the Address Translation (AR) table.

I32 rcTblArMacDeleted

1.3.6.1.4.1.2272.1.7.13

Integer32

read-only

Used to indicate the number of MAC entries deleted to the Address Translation (AR) table.

I32 rcTblArMacMoved

1.3.6.1.4.1.2272.1.7.14

Integer32

read-only

Used to indicate the number of MAC entries moved in the Address Translation (AR) table.

I32 rcTblArIpAdded

1.3.6.1.4.1.2272.1.7.15

Integer32

read-only

Used to indicate the number of IP entries added to the Address Translation (AR) table.

I32 rcTblArIpDeleted

1.3.6.1.4.1.2272.1.7.16

Integer32

read-only

Used to indicate the number of IP entries deleted to the Address Translation (AR) table.

I32 rcTblArMcastTblSize

1.3.6.1.4.1.2272.1.7.17

Integer32

read-only

Used to indicate the size of the Multicast Address Translation (AR) table.

I32 rcTblArFreeMcastGroups

1.3.6.1.4.1.2272.1.7.18

Integer32

read-only

Used to indicate the number of free multicast groups availabe in the Address Translation (AR) table.

I32 rcTblArIpMcastAdded

1.3.6.1.4.1.2272.1.7.19

Integer32

read-only

Used to indicate the number of Ip multicast entries that are added to the Address Translation (AR) table.

I32 rcTblArIpMcastDeleted

1.3.6.1.4.1.2272.1.7.20

Integer32

read-only

Used to indicate the number of Ip multicast entries that are deleted from the Address Translation (AR) table.

I32 rcTblArVlanByPortAdded

1.3.6.1.4.1.2272.1.7.21

Integer32

read-only

Used to indicate the number of VLAN by port entries that are added to the Address Translation (AR) table.

I32 rcTblArVlanByPortDeleted

1.3.6.1.4.1.2272.1.7.22

Integer32

read-only

Used to indicate the number of VLAN by port entries that are deleted from the Address Translation (AR) table.

I32 rcTblArVlanByProtocolAdded

1.3.6.1.4.1.2272.1.7.23

Integer32

read-only

Used to indicate the number of Vlans by Protocol Type entries that are added to the Address Translation (AR) table.

I32 rcTblArVlanByProtocolDeleted

1.3.6.1.4.1.2272.1.7.24

Integer32

read-only

Used to indicate the number of Vlans by Protocol Type entries that are deleted from the Address Translation (AR) table.

I32 rcTblArVlanByIpSubnetAdded

1.3.6.1.4.1.2272.1.7.25

Integer32

read-only

Used to indicate the number of VLAN by Ip entries that are added to the Address Translation (AR) table.

I32 rcTblArVlanByIpSubnetDeleted

1.3.6.1.4.1.2272.1.7.26

Integer32

read-only

Used to indicate the number of VLAN by Ip entries that are deleted from the Address Translation (AR) table.

I32 rcTblArIpSubnetsAdded

1.3.6.1.4.1.2272.1.7.27

Integer32

read-only

Used to indicate the number of Ip subnet entries that are added to the Address Translation (AR) table.

I32 rcTblArIpSubnetsDeleted

1.3.6.1.4.1.2272.1.7.28

Integer32

read-only

Used to indicate the number of Ip subnet entries that are deleted from the Address Translation (AR) table.

I32 rcTblArRsvpsAdded

1.3.6.1.4.1.2272.1.7.29

Integer32

read-only

Used to indicate the number of RSVP entries that are added to the Address Translation (AR) table.

I32 rcTblArRsvpsDeleted

1.3.6.1.4.1.2272.1.7.30

Integer32

read-only

Used to indicate the number of RSVP entries that are deleted from the Address Translation (AR) table.

I32 rcTblBrdgFdbSize

1.3.6.1.4.1.2272.1.7.31

Integer32

read-only

Used to indicate the number of entries in the dot1d forwarding database table.

I32 rcTblBrdgStaticSize

1.3.6.1.4.1.2272.1.7.32

Integer32

read-only

Used to indicate the number of entries in the dot1d Static Address Filtering table.

I32 rcTblIpAddrSize

1.3.6.1.4.1.2272.1.7.33

Integer32

read-only

Used to indicate the number of entries in the IP Address table.

I32 rcTblIpForwardingSize

1.3.6.1.4.1.2272.1.7.34

Integer32

read-only

Used to indicate the number of entries in the IP Forwarding/Best Route table.

I32 rcTblIpNetToMediaSize

1.3.6.1.4.1.2272.1.7.35

Integer32

read-only

Used to indicate the number of entries in the IP Net-to-media table.

I32 rcTblIpBestPlusAltRouteSize

1.3.6.1.4.1.2272.1.7.36

Integer32

read-only

I32 rcTblIpBestPathSize

1.3.6.1.4.1.2272.1.7.37

Integer32

read-only

I32 rcTblIpBestPlusAltPathSize

1.3.6.1.4.1.2272.1.7.38

Integer32

read-only

rcIp

1.3.6.1.4.1.2272.1.8

rcIpConf

1.3.6.1.4.1.2272.1.8.1

rcIpConfTable

1.3.6.1.4.1.2272.1.8.1.1

not-accessible

A table used to maintain IP routing information for a particular interface.

rcIpConfEntry

1.3.6.1.4.1.2272.1.8.1.1.1

not-accessible

Entry containing IP routing information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.

NUM rcIpConfIfIndex

1.3.6.1.4.1.2272.1.8.1.1.1.1

InterfaceIndexOrZero

read-only

An unique value to identify a physical interface or a logical interface (VLAN).

T/F rcIpConfAdvertDefRte

1.3.6.1.4.1.2272.1.8.1.1.1.2

TruthValue

read-write

Used to indicate whether this interface should advertize a RIP default route.

T/F rcIpConfAcceptDefRte

1.3.6.1.4.1.2272.1.8.1.1.1.3

TruthValue

read-write

Used to indicate whether this interface should accept a RIP default route.

ROW rcIpConfRowStatus

1.3.6.1.4.1.2272.1.8.1.1.1.4

RowStatus

read-write

Row status for this entry.

T/F rcIpConfRipEnable

1.3.6.1.4.1.2272.1.8.1.1.1.5

TruthValue

read-write

Enable or disable RIP routing on the specified interface.

T/F rcIpConfOspfEnable

1.3.6.1.4.1.2272.1.8.1.1.1.6

TruthValue

read-write

Enable or disable OSPF routing on the specified interface.

T/F rcIpConfIgmpEnable

1.3.6.1.4.1.2272.1.8.1.1.1.7

TruthValue

read-write

Enable or disable IGMP on the specified interface.

T/F rcIpConfAddrAssigned

1.3.6.1.4.1.2272.1.8.1.1.1.8

TruthValue

read-only

Indicate whether IpAddress has been assigned for this interface.

T/F rcIpConfDhcpEnable

1.3.6.1.4.1.2272.1.8.1.1.1.9

TruthValue

read-write

Enable or disable DHCP on the specified interface.

T/F rcIpConfTriggeredUpdateEnable

1.3.6.1.4.1.2272.1.8.1.1.1.10

TruthValue

read-write

Used to indicate whether the RIP triggered update feature should be enabled on this interface.

T/F rcIpConfAutoAggrerateEnable

1.3.6.1.4.1.2272.1.8.1.1.1.11

TruthValue

read-write

Used to indicate whether the auto aggregation feature should be enabled on this interface.

T/F rcIpConfGenerateDefaultRoute

1.3.6.1.4.1.2272.1.8.1.1.1.12

TruthValue

read-write

Used to indicate whether to generate a default RIP route on this interface.

T/F rcIpConfAdvertiseWhenDown

1.3.6.1.4.1.2272.1.8.1.1.1.13

TruthValue

read-write

The value is used indicated whether vlan state change should be notified to layer 3 or not, provided the vlan is configured as routable interface. Also used for single routable ports, in that case the criteria for state is PortOperStatus. Vlan is considered as UP if atleast one member of the port based vlan has link up, or atleast one port member of the policy based has an entry in the MGID or atleast one static member of the policy based vlan has link up. Otherwise, vlan is considered as DOWN. If the value is 'true' then the interface state change will not be notified to layer 3. (i.e., it always stays up). If the value is 'false' then the vlan state change will be notified to layer 3 so that IP related status reflects routable interface state.

T/F rcIpConfDirectBroadcastEnable

1.3.6.1.4.1.2272.1.8.1.1.1.14

TruthValue

read-write

Used to indicate whether this interface should forward direct broadcast traffic

STR rcIpConfRipInPolicy

1.3.6.1.4.1.2272.1.8.1.1.1.15

DisplayString

read-write

Used to indicate whether this interface should advertize a RIP default route.

STR rcIpConfRipOutPolicy

1.3.6.1.4.1.2272.1.8.1.1.1.16

DisplayString

read-write

Used to indicate whether this interface should accept a RIP default route.

INT rcIpConfOspfIfType

1.3.6.1.4.1.2272.1.8.1.1.1.17

INTEGER

read-write

OSPF Interface Type.

INT rcIpConfRipCost

1.3.6.1.4.1.2272.1.8.1.1.1.18

INTEGER

read-write

Used to indicate the rip cost for this interface.

INT rcIpConfRipHolddown

1.3.6.1.4.1.2272.1.8.1.1.1.19

INTEGER

read-write

Used to indicate the rip holddown timer for this interface

INT rcIpConfRipTimeout

1.3.6.1.4.1.2272.1.8.1.1.1.20

INTEGER

read-write

Used to indicate the rip timeout interval for this interface

T/F rcIpConfRsmltEnable

1.3.6.1.4.1.2272.1.8.1.1.1.21

TruthValue

read-write

Used to enable Route Smlt feature.

T/F rcIpConfReversePathCheckEnable

1.3.6.1.4.1.2272.1.8.1.1.1.22

TruthValue

read-write

Used to indicate whether this interface should perform Reverse Path Check

INT rcIpConfReversePathCheckMode

1.3.6.1.4.1.2272.1.8.1.1.1.23

INTEGER

read-write

Reverse Path Checking mode.

T/F rcIpConfIpVpnLiteEnable

1.3.6.1.4.1.2272.1.8.1.1.1.26

TruthValue

read-create

Enable or disable ipvpn-lite capability on the specified circuitless ip interface.

rcIpConfOspfTable

1.3.6.1.4.1.2272.1.8.1.2

not-accessible

A table used to maintain OSPF information for a particular interface.

rcIpConfOspfEntry

1.3.6.1.4.1.2272.1.8.1.2.1

not-accessible

Entry containing OSPF information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.

NUM rcIpConfOspfIfIndex

1.3.6.1.4.1.2272.1.8.1.2.1.1

InterfaceIndexOrZero

read-only

An unique value to identify a physical interface or a logical interface (VLAN).

INT rcIpConfOspfRtrPriority

1.3.6.1.4.1.2272.1.8.1.2.1.2

INTEGER

read-write

The priority of this interface. Used in multi- access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.

INT rcIpConfOspfMetric

1.3.6.1.4.1.2272.1.8.1.2.1.3

INTEGER

read-write

The metric for this type of service (TOS) on this interface. The default value of the TOS 0 Metric is (10^9 / ifSpeed). The value FFFF means 'no route via this TOS'. A value of 0 means the interface speed (rcIpConfOspfDefaultMetric) will be used as metric value, when the state of the interface is up.

STR rcIpConfOspfAuthKey

1.3.6.1.4.1.2272.1.8.1.2.1.4

DisplayString

read-write

The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfIfAuthKey always returns an Octet String of length zero.

ROW rcIpConfOspfRowStatus

1.3.6.1.4.1.2272.1.8.1.2.1.5

RowStatus

read-write

Row status for this entry.

INT rcIpConfOspfHelloInterval

1.3.6.1.4.1.2272.1.8.1.2.1.6

INTEGER

read-write

The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.

INT rcIpConfOspfRtrDeadInterval

1.3.6.1.4.1.2272.1.8.1.2.1.7

INTEGER

read-write

The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.

IP rcIpConfOspfIfAreaId

1.3.6.1.4.1.2272.1.8.1.2.1.8

IpAddress

read-write

A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.

INT rcIpConfOspfAuthType

1.3.6.1.4.1.2272.1.8.1.2.1.9

INTEGER

read-write

The authentication type specified for an interface. Additional authentication types may be assigned locally.

INT rcIpConfOspfPollInterval

1.3.6.1.4.1.2272.1.8.1.2.1.10

INTEGER

read-write

OSPF NBMA Interface Poll Interval.

INT rcIpConfOspfIfMtuIgnore

1.3.6.1.4.1.2272.1.8.1.2.1.11

INTEGER

read-write

Mtu-ignore flag is for ignoring the mtu checking in ospf bdb

rcIpConfOspfDefaultMetric

1.3.6.1.4.1.2272.1.8.1.3

INT rcIpConfOspfDefaultMetric10MegPort

1.3.6.1.4.1.2272.1.8.1.3.1

INTEGER

read-write

Used to indicate the cost associated with 10Meg Interface(Port).

INT rcIpConfOspfDefaultMetric100MegPort

1.3.6.1.4.1.2272.1.8.1.3.2

INTEGER

read-write

Used to indicate the cost associated with 100Meg Interface(Port).

INT rcIpConfOspfDefaultMetric1000MegPort

1.3.6.1.4.1.2272.1.8.1.3.3

INTEGER

read-write

Used to indicate the cost associated with 1000Meg Interface(Port).

INT rcIpConfOspfDefaultMetric10000MegPort

1.3.6.1.4.1.2272.1.8.1.3.4

INTEGER

read-write

Used to indicate the cost associated with 10000Meg Interface(Port).

rcIpConfOspf

1.3.6.1.4.1.2272.1.8.1.4

T/F rcIpConfOspfTrapEnable

1.3.6.1.4.1.2272.1.8.1.4.1

TruthValue

read-write

Used to indicate whether Ospf Traps should be sent.

T/F rcIpConfOspfAutoVirtLinkEnable

1.3.6.1.4.1.2272.1.8.1.4.2

TruthValue

read-write

Used to indicate whether auto virtual link creation is enabled or not. If set to true OSPF will create virtual links between ABRs whether it is needed or not, but adjacency will established only when one of the ABR losses connection to backbone area. If set to false then it is user resposibity to create virtual link whenever needed.

INT rcIpConfOspfSpfHoldDownTime

1.3.6.1.4.1.2272.1.8.1.4.3

INTEGER

read-write

The SPF Hold Down Timer value. The SPF will run at most once per hold down timer value.

INT rcIpConfOspfAction

1.3.6.1.4.1.2272.1.8.1.4.4

INTEGER

read-write

T/F rcIpConfOspfRfc1583Compatibility

1.3.6.1.4.1.2272.1.8.1.4.5

TruthValue

read-write

Controls the preference rules used when choosing among multiple AS-External-LSAs advertising the same destination. When this is enabled, the preference rule will be same as specified by RFC1583. When disabled, the new preference rule as described in RFC2328 will be applicable, which potentially prevents the routing loops when AS-External-LSAs for the same destination have been originated from different areas.

rcIpConfGlobal

1.3.6.1.4.1.2272.1.8.1.6

INT rcIpConfGlobalRipHoldDownTime

1.3.6.1.4.1.2272.1.8.1.6.1

INTEGER

read-write

Used to set the system-wide RIP hold down time in seconds.

T/F rcIpConfGlobalIcmpNetUnreach

1.3.6.1.4.1.2272.1.8.1.6.2

TruthValue

read-write

Used to set the icmp net unreach feature enable/disable.

T/F rcIpConfGlobalEcmpEnable

1.3.6.1.4.1.2272.1.8.1.6.3

TruthValue

read-write

Used to set the ecmp enable/disable.

INT rcIpConfGlobalEcmpMaxPath

1.3.6.1.4.1.2272.1.8.1.6.4

INTEGER

read-write

Used to globally configure maximum ECMP paths number.

T/F rcIpConfGlobalAlternativeEnable

1.3.6.1.4.1.2272.1.8.1.6.5

TruthValue

read-write

Used to globally configure alternative enable.

T/F rcIpConfGlobalRouteDiscoveryEnable

1.3.6.1.4.1.2272.1.8.1.6.6

TruthValue

read-write

Enable/disable ICMP Route Discovery feature

INT rcIpConfGlobalRipTimeOutInterval

1.3.6.1.4.1.2272.1.8.1.6.8

INTEGER

read-write

Rip TimeOut Interval in seconds

INT rcIpConfGlobalRipDefImportMetric

1.3.6.1.4.1.2272.1.8.1.6.9

INTEGER

read-write

Rip def import metric

STR rcIpConfGlobalEcmp1PathList

1.3.6.1.4.1.2272.1.8.1.6.10

DisplayString

read-write

Routes to networks specified in this prefix-list can have upto 1 ECMP path, irrespective of ecmp-max-path configuration

STR rcIpConfGlobalEcmp2PathList

1.3.6.1.4.1.2272.1.8.1.6.11

DisplayString

read-write

Routes to networks specified in this prefix-list can have upto 2 ECMP path, irrespective of ecmp-max-path configuration.

STR rcIpConfGlobalEcmp3PathList

1.3.6.1.4.1.2272.1.8.1.6.12

DisplayString

read-write

Routes to networks specified in this prefix-list can have upto 3 ECMP path, irrespective of ecmp-max-path configuration.

STR rcIpConfGlobalEcmp4PathList

1.3.6.1.4.1.2272.1.8.1.6.13

DisplayString

read-write

Routes to networks specified in this prefix-list can have upto 4 ECMP path, irrespective of ecmp-max-path configuration.

T/F rcIpConfGlobalEcmpPathListApply

1.3.6.1.4.1.2272.1.8.1.6.14

TruthValue

read-write

This is to apply any changes in ECMP path list configuration or in the prefix-lists configured to be used as path list

T/F rcIpConfGlobalIcmpRedirectMsg

1.3.6.1.4.1.2272.1.8.1.6.15

TruthValue

read-write

INT rcIpConfGlobalArpThreshold

1.3.6.1.4.1.2272.1.8.1.6.17

INTEGER

read-write

Defines the maximum number of outstanding arp request a switch can generate.

T/F rcIpConfGlobalAllowMoreSpecificNonLocalRouteEnable

1.3.6.1.4.1.2272.1.8.1.6.18

TruthValue

read-write

Used to determine whether more specific non local routes will go into the routing table.

T/F rcIpConfGlobalUdpCheckSumEnable

1.3.6.1.4.1.2272.1.8.1.6.19

TruthValue

read-write

Enable/disable UDP checksum calculation

T/F rcIpConfGlobalSuperNetEnable

1.3.6.1.4.1.2272.1.8.1.6.20

TruthValue

read-write

Used to globally enable Supernetting/ CIDR routing for IP

STR rcIpConfGlobalEcmp5PathList

1.3.6.1.4.1.2272.1.8.1.6.21

DisplayString

read-write

Routes to networks specified in this prefix-list can have upto 5 ECMP path, irrespective of ecmp-max-path configuration.

STR rcIpConfGlobalEcmp6PathList

1.3.6.1.4.1.2272.1.8.1.6.22

DisplayString

read-write

Routes to networks specified in this prefix-list can have upto 6 ECMP path, irrespective of ecmp-max-path configuration.

STR rcIpConfGlobalEcmp7PathList

1.3.6.1.4.1.2272.1.8.1.6.23

DisplayString

read-write

Routes to networks specified in this prefix-list can have upto 7 ECMP path, irrespective of ecmp-max-path configuration.

STR rcIpConfGlobalEcmp8PathList

1.3.6.1.4.1.2272.1.8.1.6.24

DisplayString

read-write

Routes to networks specified in this prefix-list can have upto 8 ECMP path, irrespective of ecmp-max-path configuration.

T/F rcIpConfGlobalArpMcastMacFlooding

1.3.6.1.4.1.2272.1.8.1.6.26

TruthValue

read-write

Enable/disable Ip Arp Multicast Mac Flooding feature.

rcIpConfOspfAreaTable

1.3.6.1.4.1.2272.1.8.1.7

not-accessible

A table used to maintain OSPF information for a particular Area.

rcIpConfOspfAreaEntry

1.3.6.1.4.1.2272.1.8.1.7.1

not-accessible

Entry containing OSPF Area configuration information. An entry is automatically created in this table when an area is configured through ospfAreaTable in (rfc1253rcc.mib).

IP rcIpConfOspfAreaId

1.3.6.1.4.1.2272.1.8.1.7.1.1

IpAddress

read-only

An unique value to identify an area. Area ID 0.0.0.0 is used for the OSPF backbone.

T/F rcIpConfOspfAreaImportSummary

1.3.6.1.4.1.2272.1.8.1.7.1.2

TruthValue

read-write

The area's support for importing Summary advertisements into a stub area. This field should be used only if ospfImportASExtern is set to FALSE

I32 rcIpConfOspfAreaActiveIfCount

1.3.6.1.4.1.2272.1.8.1.7.1.3

Integer32

read-only

This variable displays the number of active interfaces configured in this area. An area cannot be deleted if this value is > 0.

rcIpConfOspfAreaAggregateTable

1.3.6.1.4.1.2272.1.8.1.10

not-accessible

A table used to maintain OSPF summary route metric parameter for a particular Area range.

rcIpConfOspfAreaAggregateEntry

1.3.6.1.4.1.2272.1.8.1.10.1

not-accessible

Entry containing OSPF summary route metric parameter for a particular Area range. An entry is automatically created in this table when an area range is configured through ospfAreaAggregateTable in rfc1850rcc.mib

IP rcIpConfOspfAreaAggregateAreaID

1.3.6.1.4.1.2272.1.8.1.10.1.1

IpAddress

read-only

The Area the Address Aggregate is to be found within.

INT rcIpConfOspfAreaAggregateLsdbType

1.3.6.1.4.1.2272.1.8.1.10.1.2

INTEGER

read-only

The type of the Address Aggregate. This field specifies the Lsdb type that this Address Ag- gregate applies to.

IP rcIpConfOspfAreaAggregateNet

1.3.6.1.4.1.2272.1.8.1.10.1.3

IpAddress

read-only

The IP Address of the Net or Subnet indicated by the range.

IP rcIpConfOspfAreaAggregateMask

1.3.6.1.4.1.2272.1.8.1.10.1.4

IpAddress

read-only

The Subnet Mask that pertains to the Net or Subnet.

INT rcIpConfOspfAreaAggregateAdvertiseMetric

1.3.6.1.4.1.2272.1.8.1.10.1.5

INTEGER

read-write

Used to specify a metric for a Summary LSA (type 3) generated by OSPF through an area range. If this metric is set to 0, OSPF uses the cost to the farthest point in the networks being summarized as the metric.

INT rcIpConfOspfAreaAggregateEffect

1.3.6.1.4.1.2272.1.8.1.10.1.6

INTEGER

read-write

Subnets subsumed by ranges either trigger the advertisement of the indicated aggregate (ad- vertiseMatching), or result in the subnet's not being advertised at all outside the area.

rcIpConfRsmltTable

1.3.6.1.4.1.2272.1.8.1.11

not-accessible

A table used to maintain OSPF summary route metric parameter for a particular Area range.

rcIpConfRsmltEntry

1.3.6.1.4.1.2272.1.8.1.11.1

not-accessible

Entry containing OSPF summary route metric parameter for a particular Area range. An entry is automatically created in this table when an area range is configured through ospfAreaAggregateTable in rfc1850rcc.mib

NUM rcIpConfRsmltIfIndex

1.3.6.1.4.1.2272.1.8.1.11.1.1

InterfaceIndex

read-only

Interface Index, this is an index of the table.

INT rcIpConfRsmltHoldDownTimer

1.3.6.1.4.1.2272.1.8.1.11.1.2

INTEGER

read-write

Timer value, the range of value is from 0 to 3600.

INT rcIpConfRsmltHoldUpTimer

1.3.6.1.4.1.2272.1.8.1.11.1.3

INTEGER

read-write

The range of value 0 to 3600 or 9999. 9999 means infinity.

ROW rcIpConfRsmltRowStatus

1.3.6.1.4.1.2272.1.8.1.11.1.4

RowStatus

read-write

Row Status.

rcIpAddrTable

1.3.6.1.4.1.2272.1.8.2

not-accessible

The table of addressing information relevant to this entity's IP addresses. This table is identical to the ipAddrTable in MIB2 except the columns rcIpAdEntIfIndex and rcIpAdEntAddr are reversed. Also, the table is indexed by both these variables.

rcIpAddrEntry

1.3.6.1.4.1.2272.1.8.2.1

not-accessible

The addressing information for one of this entity's IP addresses.

NUM rcIpAdEntIfIndex

1.3.6.1.4.1.2272.1.8.2.1.1

InterfaceIndex

read-only

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

IP rcIpAdEntAddr

1.3.6.1.4.1.2272.1.8.2.1.2

IpAddress

read-only

The IP address to which this entry's addressing information pertains.

IP rcIpAdEntNetMask

1.3.6.1.4.1.2272.1.8.2.1.3

IpAddress

read-write

The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.

INT rcIpAdEntBcastAddrFormat

1.3.6.1.4.1.2272.1.8.2.1.4

INTEGER

read-only

The IP broadcast address format used on this interface.

INT rcIpAdEntReasmMaxSize

1.3.6.1.4.1.2272.1.8.2.1.5

INTEGER

read-only

The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface.

ROW rcIpAdEntRowStatus

1.3.6.1.4.1.2272.1.8.2.1.6

RowStatus

read-write

Used to create/delete entries

INT rcIpAdEntVlanId

1.3.6.1.4.1.2272.1.8.2.1.7

INTEGER

read-write

A value that uniquely identifies the Virtual LAN associated with this entry. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag.

T/F rcIpAdEntBrouterPort

1.3.6.1.4.1.2272.1.8.2.1.8

TruthValue

read-only

Used to indicate whether this entry correponds to a brouter port (as oppose to a routable VLAN). This value cannot be changed after the row is created.

INT rcIpAdEntMacOffset

1.3.6.1.4.1.2272.1.8.2.1.9

INTEGER

read-write

Used to translate the ip address into mac address. The system has 512 mac addresses of which 0-507 are reserved for Boardwalk box. 508-511 is reserved for MG. One can either mention a mac offset while configuring an ip on the vlan or it can be alloted by the system within the above range.

INT rcIpAdEntIfType

1.3.6.1.4.1.2272.1.8.2.1.10

INTEGER

read-only

The address entry IfType indicates the type of the interface. In the case of circuit-less-IP there is no association with any ports. In other words, it can be thought of as a virtual interface. The value 'brouter port' indicates this interface is associated with a specific physical port. The value 'vlan' indicates a logical port that contains one or physical ports/MLT ports.

OID rcIpAdEntVrfId

1.3.6.1.4.1.2272.1.8.2.1.12

VrfIdentifier

read-create

The VrfId used in this table is to associate VLANs or Brouter ports to a VRF after the creation of VLANs or Brouter ports. VRFID 0 is reserved for the Administrative VRF.

rcIpFlowTable

1.3.6.1.4.1.2272.1.8.3

not-accessible

IpFlow Table. This table contain entries that correspond to RSVP records in the switching fabric Address Resolution table. A connection that has a matching entry in this table will be processed with a higher priority than connections that do not have an entry.

rcIpFlowEntry

1.3.6.1.4.1.2272.1.8.3.1

not-accessible

Proprietary flow control variables.

IP rcIpFlowSrcIpAddress

1.3.6.1.4.1.2272.1.8.3.1.1

IpAddress

read-only

The source IP address of an IP packet.

INT rcIpFlowSrcIpPort

1.3.6.1.4.1.2272.1.8.3.1.2

INTEGER

read-only

The source port of an IP packet. A zero value in this field is used as a wildcard value.

IP rcIpFlowDstIpAddress

1.3.6.1.4.1.2272.1.8.3.1.3

IpAddress

read-only

The destination IP address of an IP packet.

INT rcIpFlowDstIpPort

1.3.6.1.4.1.2272.1.8.3.1.4

INTEGER

read-only

The destination port of an IP packet. A zero value in this field is used as a wildcard value.

INT rcIpFlowProtocol

1.3.6.1.4.1.2272.1.8.3.1.5

INTEGER

read-only

The protocol type of an IP packet. A zero value in this field is used as a wildcard value.

ROW rcIpFlowRowStatus

1.3.6.1.4.1.2272.1.8.3.1.6

RowStatus

read-write

Status of entry.

rcIpRouteTable

1.3.6.1.4.1.2272.1.8.7

not-accessible

This entity's IP Routing table.

rcIpRouteEntry

1.3.6.1.4.1.2272.1.8.7.1

not-accessible

A route to a particular destination.

IP rcIpRouteDest

1.3.6.1.4.1.2272.1.8.7.1.1

IpAddress

read-only

The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.

IP rcIpRouteMask

1.3.6.1.4.1.2272.1.8.7.1.2

IpAddress

read-only

Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the rcIpRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the rcIpRouteMask by determining whether the value of the correspondent rcIpRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the rcIpRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.

IP rcIpRouteNextHop

1.3.6.1.4.1.2272.1.8.7.1.3

IpAddress

read-write

The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface).

I32 rcIpRouteMetric

1.3.6.1.4.1.2272.1.8.7.1.4

Integer32

read-write

The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's rcIpRouteProto value. If this metric is not used, its value should be set to -1.

NUM rcIpRouteIfIndex

1.3.6.1.4.1.2272.1.8.7.1.5

InterfaceIndex

read-only

The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

INT rcIpRouteType

1.3.6.1.4.1.2272.1.8.7.1.6

INTEGER

read-only

The type of route.

INT rcIpRouteProto

1.3.6.1.4.1.2272.1.8.7.1.7

INTEGER

read-only

The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.

I32 rcIpRouteAge

1.3.6.1.4.1.2272.1.8.7.1.8

Integer32

read-only

The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned.

ROW rcIpRouteRowStatus

1.3.6.1.4.1.2272.1.8.7.1.9

RowStatus

read-write

Used to create/delete entries

INT rcIpRoutePref

1.3.6.1.4.1.2272.1.8.7.1.10

INTEGER

read-only

I32 rcIpRouteAltSequence

1.3.6.1.4.1.2272.1.8.7.1.11

Integer32

read-only

Alternative Route Sequence. 0 denotes Best Route.

INT rcIpRoutePathType

1.3.6.1.4.1.2272.1.8.7.1.12

INTEGER

read-only

The type of route. It is a combination of direct, indirect, best, alternative and ECMP path.

OID rcIpRouteSrcVrfId

1.3.6.1.4.1.2272.1.8.7.1.13

VrfIdentifier

read-write

srcVrfId of the next-hop address

STR rcIpRouteNextHopId

1.3.6.1.4.1.2272.1.8.7.1.14

DisplayString

read-only

Identifier of the next-hop, hostname or mac adress.

rcIpConfDhcpTable

1.3.6.1.4.1.2272.1.8.8

not-accessible

DHCP configuration table

rcIpConfDhcpEntry

1.3.6.1.4.1.2272.1.8.8.1

not-accessible

Used to configure DHCP on a particular port. An entry is created automatically when the variable rcIpConfDhcpEnable is set to TRUE. Once created this entry will only be deleted if the rcIpConfDhcpRowStatus is set to 'destroy(6)'. In which case, the rcIpConfDhcpEnable is automatically reset to the FALSE setting.

NUM rcIpConfDhcpIfIndex

1.3.6.1.4.1.2272.1.8.8.1.1

InterfaceIndexOrZero

read-only

Interface number. The number can represent either a physical or logical(VLAN) interface.

INT rcIpConfDhcpMaxHop

1.3.6.1.4.1.2272.1.8.8.1.2

INTEGER

read-write

Used to indicate the maximum number of hops a DHCP packet can take from the source device to the destination device (i.e., DHCP client to DHCP server).

INT rcIpConfDhcpMinSec

1.3.6.1.4.1.2272.1.8.8.1.3

INTEGER

read-write

Used to indicate the minimum number of seconds to wait between receiving a DHCP packet and actually forwarding the DHCP packet to the destination device. A value of zero(0) indicates forwarding should be done immediately without any delay.

INT rcIpConfDhcpMode

1.3.6.1.4.1.2272.1.8.8.1.4

INTEGER

read-write

Used to indicate what type of DHCP packets this interface should support. A value of none(1) will result in all incoming DHCP and BOOTP packets to be dropped.

ROW rcIpConfDhcpRowStatus

1.3.6.1.4.1.2272.1.8.8.1.5

RowStatus

read-write

An entry is created automatically when the variable rcIpConfDhcpEnable is set to TRUE. Once created this entry will only be deleted if the rcIpConfDhcpRowStatus is set to 'destroy(6)'. In which case, the rcIpConfDhcpEnable is automatically reset to the FALSE setting.

C32 rcIpConfDhcpNumRequests

1.3.6.1.4.1.2272.1.8.8.1.6

Counter32

read-only

The total number of DHCP requests seen on this interface.

C32 rcIpConfDhcpNumReplies

1.3.6.1.4.1.2272.1.8.8.1.7

Counter32

read-only

The total number of DHCP replies seen on this interface.

T/F rcIpConfDhcpAlwaysBroadcast

1.3.6.1.4.1.2272.1.8.8.1.8

TruthValue

read-write

Used to indicate if DHCP Reply packets should be broadcast to the DHCP client on this interface.

T/F rcIpConfDhcpCircuitId

1.3.6.1.4.1.2272.1.8.8.1.11

TruthValue

read-write

Used to indicate if DHCP packets should have option82 circuitId info inserted before sent to servers, for this interface.

T/F rcIpConfDhcpRemoteId

1.3.6.1.4.1.2272.1.8.8.1.12

TruthValue

read-write

Used to indicate if DHCP packets should have option82 remoteId info inserted before sent to servers, for this interface.

T/F rcIpConfDhcpTrusted

1.3.6.1.4.1.2272.1.8.8.1.13

TruthValue

read-write

Used to indicate if DHCP packets come through a trusted dhcp circuit. This means that packets with giaddr set to 0 having option82 in it, will be forwarded if the circuit is trusted.

IP rcIpConfDhcpAgentAddr

1.3.6.1.4.1.2272.1.8.8.1.14

IpAddress

read-only

The IP address configured as relay on this interface; it is either the IP of the physical interface or the IP of the VRRP address

rcIpDhcpForwardTable

1.3.6.1.4.1.2272.1.8.9

not-accessible

DHCP forwarding table.

rcIpDhcpForwardEntry

1.3.6.1.4.1.2272.1.8.9.1

not-accessible

An entry used represents a DHCP forwarding directive.

IP rcIpDhcpForwardAgentAddr

1.3.6.1.4.1.2272.1.8.9.1.1

IpAddress

read-only

The IP address configured on an interface (i.e., a locally configured IP address).

IP rcIpDhcpForwardServerAddr

1.3.6.1.4.1.2272.1.8.9.1.2

IpAddress

read-only

The IP address of the DHCP server. If this IP address corresponds to a locally configured IP network, the DHCP packet is broadcasted out the interface the IP address is assigned to. This behavior is known as 'relay agent' mode. If this IP address is a remote address, the DHCP packet is sent via unicast to the remote device. This behavior is known as 'preferred server' mode.

T/F rcIpDhcpForwardEnable

1.3.6.1.4.1.2272.1.8.9.1.3

TruthValue

read-write

Used to indicate whether is entry should be used.

INT rcIpDhcpForwardMode

1.3.6.1.4.1.2272.1.8.9.1.4

INTEGER

read-write

Used to indicate whether this entry pertains to BOOTP packets, DHCP packets, or both.

ROW rcIpDhcpForwardRowStatus

1.3.6.1.4.1.2272.1.8.9.1.5

RowStatus

read-write

Row status of this entry.

rcIpUdp

1.3.6.1.4.1.2272.1.8.13

I32 rcIpUdpProtocolTableSize

1.3.6.1.4.1.2272.1.8.13.1

Integer32

read-only

Used to indicate the number of entries in the rcIpUdpProtocolTable.

rcIpUdpProtocolTable

1.3.6.1.4.1.2272.1.8.13.2

not-accessible

list of UDP protocols. Used to determine whether to forward the UDP broadcast packet or not.

rcIpUdpProtocolEntry

1.3.6.1.4.1.2272.1.8.13.2.1

not-accessible

Used to include a particular UDP port in the table. An entry in this table indicates that the box might do forwarding of UDP broadcast packets if there is a matching entry for this packet in the rcIpUdpPortFwdTable.

INT rcIpUdpProtocolPortNumber

1.3.6.1.4.1.2272.1.8.13.2.1.1

INTEGER

read-only

well-known UDP Port number. Pre-assigned port number for this protocol. Port used by the server process as its contact port. It cannot be BOOTP/DHCP port#s 67, 68.

STR rcIpUdpProtocolName

1.3.6.1.4.1.2272.1.8.13.2.1.2

DisplayString

read-write

Used to indicate the name of the protocol that is running on top of UDP protocol. cannot change the name once created. This should be set while creating the entry.

ROW rcIpUdpProtocolRowStatus

1.3.6.1.4.1.2272.1.8.13.2.1.3

RowStatus

read-write

Rowstatus of this entry.

I32 rcIpUdpPortFwdTableSize

1.3.6.1.4.1.2272.1.8.13.3

Integer32

read-only

Used to indicate the number of entries in the rcIpUdpPortFwdTable.

rcIpUdpPortFwdTable

1.3.6.1.4.1.2272.1.8.13.4

not-accessible

Udp forward entry table.

rcIpUdpPortFwdEntry

1.3.6.1.4.1.2272.1.8.13.4.1

not-accessible

An entry is configured to specify forwarding policy parameters.

INT rcIpUdpPortFwdDestPort

1.3.6.1.4.1.2272.1.8.13.4.1.1

INTEGER

read-only

The well-known port number defined for UDP/TCP depending on the value of IpProtoType field in this entry. This port number has to be defined in the rcIpUdpProtoTable. In order to select this policy the destination port number has to match the DestPort value.

IP rcIpUdpPortFwdDestAddr

1.3.6.1.4.1.2272.1.8.13.4.1.2

IpAddress

read-only

Destination IP address. The IP addres to which the UDP/TCP broadcast should be forwarded. This IP address can be any IP server address or subnet broadcast address. If the IP address is one of the routable interface's address on the router, the frame will be rebroadcast out as a limited broadcast. If the Ip address is that of a server then the received broadcast packet will be sent as a unicast packet to this address.

I32 rcIpUdpPortFwdId

1.3.6.1.4.1.2272.1.8.13.4.1.3

Integer32

read-only

Identifier of this entry. Used internally to identify this entry.

INT rcIpUdpPortFwdFwdListIdListSize

1.3.6.1.4.1.2272.1.8.13.4.1.4

INTEGER

read-only

Used to indicate the number of id(s) in the rcIpUdpPortFwdListId variable.

IDL rcIpUdpPortFwdFwdListIdList

1.3.6.1.4.1.2272.1.8.13.4.1.5

IdList

read-only

Used to indicate zero or more rcIpUdpPortFwdListEntry(s) that are referring to this entry. Each list-id identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.

C32 rcIpUdpPortFwdNumFwdPackets

1.3.6.1.4.1.2272.1.8.13.4.1.6

Counter32

read-only

The total number of UDP/TCP broadcast packets forwarded using this policy.

C32 rcIpUdpPortFwdNumDropPacketsTtlExpired

1.3.6.1.4.1.2272.1.8.13.4.1.7

Counter32

read-only

The total number of UDP/TCP broadcast packets dropped because the TTL has expired.

C32 rcIpUdpPortFwdNumDropPacketsDestUnreach

1.3.6.1.4.1.2272.1.8.13.4.1.8

Counter32

read-only

The total number of UDP/TCP broadcast packets dropped because the rcIpUdpPortFwdDestAddr specified in this policy was unreachable.

ROW rcIpUdpPortFwdRowStatus

1.3.6.1.4.1.2272.1.8.13.4.1.9

RowStatus

read-write

Row status of this entry.

I32 rcIpUdpPortFwdListTableSize

1.3.6.1.4.1.2272.1.8.13.5

Integer32

read-only

Used to indicate the number of entries in the rcIpUdpPortFwdListTable.

rcIpUdpPortFwdListTable

1.3.6.1.4.1.2272.1.8.13.6

not-accessible

A table used to group rcIpUdpPortFwdEntry(s) into a list.

rcIpUdpPortFwdListEntry

1.3.6.1.4.1.2272.1.8.13.6.1

not-accessible

Route entry attributes.

INT rcIpUdpPortFwdListId

1.3.6.1.4.1.2272.1.8.13.6.1.1

INTEGER

read-only

A value that uniquely identifies this list of rcIpUdpPortFwdListEntry.

STR rcIpUdpPortFwdListName

1.3.6.1.4.1.2272.1.8.13.6.1.3

DisplayString

read-write

An administratively-assigned name for this list.

INT rcIpUdpPortFwdListFwdIdListSize

1.3.6.1.4.1.2272.1.8.13.6.1.4

INTEGER

read-only

Used to indicate the number of rcIpUdpPortFwdNetEntry id(s) in the rcIpUdpPortFwdListIdList variable.

OCT rcIpUdpPortFwdListFwdIdList

1.3.6.1.4.1.2272.1.8.13.6.1.5

OCTET STRING

read-write

Used to indicate zero or more UdpPortFwd entries that are associated to this list. Each entry identifier is stored as two bytes in this array starting from offset zero. Any unused bytes should be set to zero.

ROW rcIpUdpPortFwdListRowStatus

1.3.6.1.4.1.2272.1.8.13.6.1.6

RowStatus

read-write

Row status of this entry.

I32 rcIpUdpConfBroadcastIntfTableSize

1.3.6.1.4.1.2272.1.8.13.7

Integer32

read-only

Used to indicate the number of entries in the rcIpUdpBroadcastIntfTable.

rcIpUdpConfBroadcastIntfTable

1.3.6.1.4.1.2272.1.8.13.8

not-accessible

IP broadcast forward configuration table

rcIpUdpConfBroadcastIntfEntry

1.3.6.1.4.1.2272.1.8.13.8.1

not-accessible

Used to configure UDP broadcast forward on a particular interface.

IP rcIpUdpConfBroadcastIntfLocalIfAddr

1.3.6.1.4.1.2272.1.8.13.8.1.1

IpAddress

read-only

The ip address of the local interface that is partipating in the forwarding UDP broadcast packets.

INT rcIpUdpConfBroadcastIntfUdpPortFwdListId

1.3.6.1.4.1.2272.1.8.13.8.1.2

INTEGER

read-write

Used to indicate the number UDP ports that this interface is configured to forward. A value of '0' indicates that this interface will not forward any UDP broadcast packets. This is a required field to create an entry.

INT rcIpUdpConfBroadcastIntfMaxTtl

1.3.6.1.4.1.2272.1.8.13.8.1.3

INTEGER

read-write

Used to indicate the maximum number of hops an IP broadcast packet can take from the source device to the destination device.

C32 rcIpUdpConfBroadcastIntfNumRxPkts

1.3.6.1.4.1.2272.1.8.13.8.1.4

Counter32

read-only

The total number of UDP/TCP broadcast packets received by this local interface.

C32 rcIpUdpConfBroadcastIntfNumFwdPkts

1.3.6.1.4.1.2272.1.8.13.8.1.5

Counter32

read-only

The total number of UDP/TCP broadcast packets forwarded.

C32 rcIpUdpConfBroadcastIntfNumDropPktsMaxTtlExpired

1.3.6.1.4.1.2272.1.8.13.8.1.6

Counter32

read-only

The total number of UDP/TCP broadcast packets dropped because the TTL has expired.

C32 rcIpUdpConfBroadcastIntfNumDropPktsDestUnreach

1.3.6.1.4.1.2272.1.8.13.8.1.7

Counter32

read-only

The total number of UDP broadcast packets dropped because the destination was unreachable.

C32 rcIpUdpConfBroadcastIntfNumDropPktsUnknownPort

1.3.6.1.4.1.2272.1.8.13.8.1.8

Counter32

read-only

The total number of UDP/TCP broadcast packets dropped because the destination port/protocol specified has no matching forwarding policy.

ROW rcIpUdpConfBroadcastIntfRowStatus

1.3.6.1.4.1.2272.1.8.13.8.1.9

RowStatus

read-write

Entry row status.

IP rcIpUdpConfBroadcastIntfBroadCastMask

1.3.6.1.4.1.2272.1.8.13.8.1.10

IpAddress

read-write

The subnet mask of the local interface that is used for broadcasting the UDP broadcast packets.

rcIpPim

1.3.6.1.4.1.2272.1.8.16

rcIpPimGlobal

1.3.6.1.4.1.2272.1.8.16.1

T/F rcIpPimGlobalEnable

1.3.6.1.4.1.2272.1.8.16.1.1

TruthValue

read-write

enable feature

INT rcIpPimGlobalMode

1.3.6.1.4.1.2272.1.8.16.1.2

INTEGER

read-write

INT rcIpPimGlobalRegisterSuppTimer

1.3.6.1.4.1.2272.1.8.16.1.4

INTEGER

read-write

Each source's DR maintains, per (S,G), a Register- Suppression-timer in seconds. The Register- Suppression-timer is started by the Register-Stop message; upon expiration, the source's DR resumes sending data packets to the RP, encapsulated in the Register message.

I32 rcIpPimGlobalInterfaceTableSize

1.3.6.1.4.1.2272.1.8.16.1.5

Integer32

read-only

table size

INT rcIpPimGlobalUniRouteChgTimeOut

1.3.6.1.4.1.2272.1.8.16.1.6

INTEGER

read-write

This timer allows a better tuning on how fast the routing information is going to get updated from RTM (the frequency at which the RTM is polled for routing information updates).

INT rcIpPimGlobalDiscardDataTimeOut

1.3.6.1.4.1.2272.1.8.16.1.7

INTEGER

read-write

This timer is used to discard data until the Join is received from the RP. A ipmc discard record is created and deleted once the timer expires and/or when a Join is received.

INT rcIpPimGlobalCRPADVTimeOut

1.3.6.1.4.1.2272.1.8.16.1.8

INTEGER

read-write

Routers configured as candidate RPs use this timer to periodically send C-RP-Adv messages. Upon expiry, a C-RP-Adv message is sent to the elected BSR.

INT rcIpPimGlobalBootStrapPeriod

1.3.6.1.4.1.2272.1.8.16.1.9

INTEGER

read-write

At the elected BSR, this is the interval between originating Bootstrap messages.

T/F rcIpPimGlobalStaticRP

1.3.6.1.4.1.2272.1.8.16.1.10

TruthValue

read-write

Enable/Disable Static RP feature.

INT rcIpPimGlobalFwdCacheTimeOut

1.3.6.1.4.1.2272.1.8.16.1.12

INTEGER

read-write

PIM forward cache expiry value in seconds.This value is going to be used in aging PIM mroutes in seconds.

ENA rcIpPimGlobalFastJoinPrune

1.3.6.1.4.1.2272.1.8.16.1.13

EnableValue

read-write

Pim Fast Join Prune.

rcIpPimTable

1.3.6.1.4.1.2272.1.8.16.2

not-accessible

IP Pim table

rcIpPimEntry

1.3.6.1.4.1.2272.1.8.16.2.1

not-accessible

An entry of Ip Pim Table.

NUM rcIpPimIfIndex

1.3.6.1.4.1.2272.1.8.16.2.1.1

InterfaceIndex

read-only

port

T/F rcIpPimEnable

1.3.6.1.4.1.2272.1.8.16.2.1.2

TruthValue

read-write

enable interface

INT rcIpPimMode

1.3.6.1.4.1.2272.1.8.16.2.1.3

INTEGER

read-write

INT rcIpPimHelloInterval

1.3.6.1.4.1.2272.1.8.16.2.1.4

INTEGER

read-write

frq. at which hello sent.

INT rcIpPimJoinPruneInterval

1.3.6.1.4.1.2272.1.8.16.2.1.5

INTEGER

read-write

INT rcIpPimCBSRPreference

1.3.6.1.4.1.2272.1.8.16.2.1.6

INTEGER

read-write

INT rcIpPimIntfType

1.3.6.1.4.1.2272.1.8.16.2.1.7

INTEGER

read-write

Pim interface type.

rcIpPimInterfaceTable

1.3.6.1.4.1.2272.1.8.16.3

not-accessible

IP Pim table

rcIpPimInterfaceEntry

1.3.6.1.4.1.2272.1.8.16.3.1

not-accessible

An entry of Ip Pim Interface Table.

NUM rcIpPimInterfaceIfIndex

1.3.6.1.4.1.2272.1.8.16.3.1.1

InterfaceIndex

read-only

port

INT rcIpPimInterfaceOperState

1.3.6.1.4.1.2272.1.8.16.3.1.2

INTEGER

read-only

The current operational state of this PIM interface. This object is deprecated in favor of ifOperStatus.

INT rcIpPimInterfaceType

1.3.6.1.4.1.2272.1.8.16.3.1.3

INTEGER

read-write

Pim interface type.

rcIpPimStaticRPTable

1.3.6.1.4.1.2272.1.8.16.4

not-accessible

The table lists all the RPs configured statically for various IP multicast groups.

rcIpPimStaticRPEntry

1.3.6.1.4.1.2272.1.8.16.4.1

not-accessible

An entry (conceptual row) in the rcIpPimStaticRPTable.

IP rcIpPimStaticRPGroupAddress

1.3.6.1.4.1.2272.1.8.16.4.1.1

IpAddress

read-only

The IP multicast group address which, when combined with rcIpPimStaticRPGroupMask, identifies a group prefix for which rcIpPimStaticRPAddress is a static-RP.

IP rcIpPimStaticRPGroupMask

1.3.6.1.4.1.2272.1.8.16.4.1.2

IpAddress

read-only

The multicast group address mask which, when combined with rcIpPimStaticRPGroupAddress, identifies a group prefix for which rcIpPimStaticRPAddress is a static-RP.

IP rcIpPimStaticRPAddress

1.3.6.1.4.1.2272.1.8.16.4.1.3

IpAddress

read-only

The (unicast) address of the static-RP.

ROW rcIpPimStaticRPRowStatus

1.3.6.1.4.1.2272.1.8.16.4.1.4

RowStatus

read-write

The status of this row, by which new entries may be created, or old entries deleted from this table.

INT rcIpPimStaticRPStatus

1.3.6.1.4.1.2272.1.8.16.4.1.5

INTEGER

read-only

The status of StaticRP.

rcIpPimCurrBsr

1.3.6.1.4.1.2272.1.8.16.5

IP rcIpPimCurrBsrAddress

1.3.6.1.4.1.2272.1.8.16.5.1

IpAddress

read-only

Current BSR address

I32 rcIpPimCurrBsrFragmentTag

1.3.6.1.4.1.2272.1.8.16.5.2

Integer32

read-only

Current BSR Fragment Tag

IP rcIpPimCurrBsrHashMask

1.3.6.1.4.1.2272.1.8.16.5.3

IpAddress

read-only

Current BSR Hash Mask value

I32 rcIpPimCurrBsrPriority

1.3.6.1.4.1.2272.1.8.16.5.4

Integer32

read-only

Current BSR Priority

I32 rcIpPimCurrBsrBootStrapTimer

1.3.6.1.4.1.2272.1.8.16.5.5

Integer32

read-only

Current BSR Boot Strap Timer

rcIpPimVirtualNbrTable

1.3.6.1.4.1.2272.1.8.16.6

not-accessible

Table listing the router's virtual PIM neighbors

rcIpPimVirtualNbrEntry

1.3.6.1.4.1.2272.1.8.16.6.1

not-accessible

An entry in the virtual PIM neighbors' table.

IP rcIpPimVirtualNbrAddress

1.3.6.1.4.1.2272.1.8.16.6.1.1

IpAddress

not-accessible

The IP address of the virtual PIM neighbor for which this entry contains information.

NUM rcIpPimVirtualNbrIfIndex

1.3.6.1.4.1.2272.1.8.16.6.1.2

InterfaceIndex

read-create

The value of ifIndex for the PIM interface in which this virtual neighbor is created. This value is mandatory while trying to create a virtual PIM neighbor.

ROW rcIpPimVirtualNbrRowStatus

1.3.6.1.4.1.2272.1.8.16.6.1.3

RowStatus

read-create

To create/delete an entry in the virtual PIM neighbors' table.

rcIpMulticastArpTable

1.3.6.1.4.1.2272.1.8.17

not-accessible

IP Multicast Arp table

rcIpMulticastArpEntry

1.3.6.1.4.1.2272.1.8.17.1

not-accessible

An entry of Ip Multicast Arp Table.

I32 rcIpMulticastArpVlanId

1.3.6.1.4.1.2272.1.8.17.1.1

Integer32

read-only

vlan id

MAC rcIpMulticastArpMacAddress

1.3.6.1.4.1.2272.1.8.17.1.2

MacAddress

read-only

multicast mac address

IP rcIpMulticastArpIpAddress

1.3.6.1.4.1.2272.1.8.17.1.3

IpAddress

read-only

multicast ip address

POR rcIpMulticastArpPorts

1.3.6.1.4.1.2272.1.8.17.1.4

PortSet

read-write

ports within a particular vlan

I32 rcIpMulticastArpNumMltIds

1.3.6.1.4.1.2272.1.8.17.1.5

Integer32

read-only

number of mlt ids

IDL rcIpMulticastArpMltIds

1.3.6.1.4.1.2272.1.8.17.1.6

IdList

read-write

mlt id

ROW rcIpMulticastArpRowStatus

1.3.6.1.4.1.2272.1.8.17.1.7

RowStatus

read-write

row status

rcIpRipInterface

1.3.6.1.4.1.2272.1.8.20

rcIpRipInterfaceTable

1.3.6.1.4.1.2272.1.8.20.1

not-accessible

IP Rip Interface table

rcIpRipInterfaceEntry

1.3.6.1.4.1.2272.1.8.20.1.1

not-accessible

An entry of Ip Rip Interface Table.

IP rcIpRipInterfaceAddress

1.3.6.1.4.1.2272.1.8.20.1.1.1

IpAddress

read-only

Ip Address

NUM rcIpRipInterfaceIfIndex

1.3.6.1.4.1.2272.1.8.20.1.1.2

InterfaceIndex

read-only

Rip Interface If Index.

ENA rcIpRipInterfaceRipEnable

1.3.6.1.4.1.2272.1.8.20.1.1.3

EnableValue

read-write

T/F rcIpRipInterfaceAccDefRte

1.3.6.1.4.1.2272.1.8.20.1.1.4

TruthValue

read-write

T/F rcIpRipInterfaceAdvDefRte

1.3.6.1.4.1.2272.1.8.20.1.1.5

TruthValue

read-write

T/F rcIpRipInterfaceAutoAggregate

1.3.6.1.4.1.2272.1.8.20.1.1.6

TruthValue

read-write

I32 rcIpRipInterfaceCost

1.3.6.1.4.1.2272.1.8.20.1.1.7

Integer32

read-write

T/F rcIpRipInterfaceListen

1.3.6.1.4.1.2272.1.8.20.1.1.8

TruthValue

read-write

T/F rcIpRipInterfacePoison

1.3.6.1.4.1.2272.1.8.20.1.1.9

TruthValue

read-write

T/F rcIpRipInterfaceSupply

1.3.6.1.4.1.2272.1.8.20.1.1.10

TruthValue

read-write

T/F rcIpRipInterfaceTriggeredUpdate

1.3.6.1.4.1.2272.1.8.20.1.1.11

TruthValue

read-write

STR rcIpRipInterfaceInPolicy

1.3.6.1.4.1.2272.1.8.20.1.1.12

DisplayString

read-write

STR rcIpRipInterfaceOutPolicy

1.3.6.1.4.1.2272.1.8.20.1.1.13

DisplayString

read-write

T/F rcIpRipInterfaceProxyAnnounceFlag

1.3.6.1.4.1.2272.1.8.20.1.1.14

TruthValue

read-write

INT rcIpRipInterfaceHolddown

1.3.6.1.4.1.2272.1.8.20.1.1.15

INTEGER

read-write

Used to indicate the rip holddown timer for this interface

INT rcIpRipInterfaceTimeout

1.3.6.1.4.1.2272.1.8.20.1.1.16

INTEGER

read-write

Used to indicate the rip timeout interval for this interface

rcIpMulticastTimedPruneTable

1.3.6.1.4.1.2272.1.8.21

not-accessible

This feature provides the ability for the user to create (S,G) Forwarding Entries that would not be pruned until a configurable timer expires. This feature is targeted for Passport 8600. Currently the timer value is set to 0.

rcIpMulticastTimedPruneEntry

1.3.6.1.4.1.2272.1.8.21.1

not-accessible

An entry of Ip Multicast Timed Prune Table.

IP rcIpMulticastTimedPruneGroupAddress

1.3.6.1.4.1.2272.1.8.21.1.1

IpAddress

read-write

This field indicates the IP Multicast Group Address associated with the IP multicast stream.

IP rcIpMulticastTimedPruneSourceAddress

1.3.6.1.4.1.2272.1.8.21.1.2

IpAddress

read-write

This is the Source Subnet IP address of the sender of the IP multicast stream.

IP rcIpMulticastTimedPruneSrcSubnetMask

1.3.6.1.4.1.2272.1.8.21.1.3

IpAddress

read-write

This is the Source Subnet Mask IP address of the sender of the IP multicast stream.

I32 rcIpMulticastTimedPruneAgingTimer

1.3.6.1.4.1.2272.1.8.21.1.4

Integer32

read-write

This field represents the amount of time (in minutes) this timed prune entry will be kept in the forwarding table when there are no more receivers. After this timer expires, this timed prune entry would be treated as a normal DVMRP/PIM forwarding entry. Aging Timer value of 0 (infinite time) indicates this timed prune entry will not be deleted even when there are no more receivers.

I32 rcIpMulticastTimedPruneTimeLeft

1.3.6.1.4.1.2272.1.8.21.1.5

Integer32

read-only

This read-only field represents the remaining time for which this timed prune entry will be kept in the forwarding table. After this timer expires, this timed prune entry would be treated as a normal DVMRP/PIM forwarding entry. 0 in this field indicates that this entry would not be aged out.

TIK rcIpMulticastTimedPruneLastActivity

1.3.6.1.4.1.2272.1.8.21.1.6

TimeTicks

read-only

This read-only field represents the actual time since the traffic has come from this Source, Group pair.

ROW rcIpMulticastTimedPruneRowStatus

1.3.6.1.4.1.2272.1.8.21.1.7

RowStatus

read-write

row status

rcIpConfIcmpRdiscTable

1.3.6.1.4.1.2272.1.8.22

not-accessible

A table used to maintain ICMP Route discovery information for a particular interface.

rcIpConfIcmpRdiscEntry

1.3.6.1.4.1.2272.1.8.22.1

not-accessible

Entry containing ICMP Rdisc information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface.

INT rcIpConfIcmpRdiscIfIndex

1.3.6.1.4.1.2272.1.8.22.1.1

INTEGER

read-only

An unique value to identify a physical interface or a logical interface (VLAN).

IP rcIpConfIcmpRdiscAdvAddress

1.3.6.1.4.1.2272.1.8.22.1.2

IpAddress

read-write

Advertisement address to which the route discovery advertisements transmitted on this interface.

T/F rcIpConfIcmpRdiscAdvFlag

1.3.6.1.4.1.2272.1.8.22.1.3

TruthValue

read-write

Flag to indicate whether or not the address is to be advertised on this interface.

INT rcIpConfIcmpRdiscAdvLifetime

1.3.6.1.4.1.2272.1.8.22.1.4

INTEGER

read-write

The value to be placed in the lifetime field of Router Advertisements sent from the interface.

INT rcIpConfIcmpRdiscMaxAdvInterval

1.3.6.1.4.1.2272.1.8.22.1.5

INTEGER

read-write

The maximum time allowed between sending Router Advertisements from this interface.

INT rcIpConfIcmpRdiscMinAdvInterval

1.3.6.1.4.1.2272.1.8.22.1.6

INTEGER

read-write

The minimum time allowed between sending Router Advertisements from this interface.

INT rcIpConfIcmpRdiscPreferenceLevel

1.3.6.1.4.1.2272.1.8.22.1.7

INTEGER

read-write

Preferability of the router address as a default Router

rcIpMulticastSoftwareForwarding

1.3.6.1.4.1.2272.1.8.23

T/F rcIpMulticastSoftwareForwardingEnable

1.3.6.1.4.1.2272.1.8.23.1

TruthValue

read-write

Enable/Disable multicast software forwarding.

rcIpMrouteHw

1.3.6.1.4.1.2272.1.8.24

rcIpMrouteHwTable

1.3.6.1.4.1.2272.1.8.24.1

not-accessible

The (conceptual) table containing hardware entries of multicast routing information for all the Group Address.

rcIpMrouteHwEntry

1.3.6.1.4.1.2272.1.8.24.1.1

not-accessible

An entry (conceptual row) containing hardware entries of multicast routing information for a particular Group Address.

IP rcIpMrouteHwGroupAddress

1.3.6.1.4.1.2272.1.8.24.1.1.1

IpAddress

read-only

The IP multicast group address for which this entry contains multicast routing information.

IP rcIpMrouteHwSubnet

1.3.6.1.4.1.2272.1.8.24.1.1.2

IpAddress

read-only

The network address from where the source is sending the stream of traffic for which this entry contains multicast routing information.

RCV rcIpMrouteHwInvlan

1.3.6.1.4.1.2272.1.8.24.1.1.3

RcVlanIdOrNone

read-only

The Ingress vlan Id from where the traffic is coming for which this entry contains multicast routing information.

T/F rcIpMrouteHwPruned

1.3.6.1.4.1.2272.1.8.24.1.1.4

TruthValue

read-only

This is to show weather the entry containing multicast routing information has received Prune message or not.

I32 rcIpMrouteHwIndex

1.3.6.1.4.1.2272.1.8.24.1.1.5

Integer32

read-only

This Index value keep tracks of the hardware record that has been accessed for displaying the entry containing multicast routing information.

rcIpMrouteHwPrunesTable

1.3.6.1.4.1.2272.1.8.24.2

not-accessible

The (conceptual) table containing prune entries of multicast routing information for the Group Address.

rcIpMrouteHwPrunesEntry

1.3.6.1.4.1.2272.1.8.24.2.1

not-accessible

An entry (conceptual row) containing prune entries of multicast routing information for a particular Group Address.

IP rcIpMrouteHwPrunesGroupAddress

1.3.6.1.4.1.2272.1.8.24.2.1.1

IpAddress

read-only

The IP multicast group address for which this entry contains multicast routing information.

IP rcIpMrouteHwPrunesSubnet

1.3.6.1.4.1.2272.1.8.24.2.1.2

IpAddress

read-only

The network address from where the source is sending the stream of traffic for which this entry contains multicast routing information.

RCV rcIpMrouteHwPrunesInvlan

1.3.6.1.4.1.2272.1.8.24.2.1.3

RcVlanIdOrNone

read-only

The Ingress vlan Id from where the traffic is coming for which this entry contains multicast routing information.

IP rcIpMrouteHwPrunesNeighbor

1.3.6.1.4.1.2272.1.8.24.2.1.4

IpAddress

read-only

The IpAddress from where the Prune message has been received.

I32 rcIpMrouteHwPrunesTimer

1.3.6.1.4.1.2272.1.8.24.2.1.5

Integer32

read-only

This is to show how much time is left for this particular entry containing multicast routing information during which the graft message can be sent.

rcIpMrouteHwSourcesTable

1.3.6.1.4.1.2272.1.8.24.3

not-accessible

The (conceptual) table containing source entries of multicast routing information for the Group Address.

rcIpMrouteHwSourcesEntry

1.3.6.1.4.1.2272.1.8.24.3.1

not-accessible

An entry (conceptual row) containing source entries of multicast routing information for a particular Group Address.

IP rcIpMrouteHwSourcesGroupAddress

1.3.6.1.4.1.2272.1.8.24.3.1.1

IpAddress

read-only

The IP multicast group address for which this entry contains multicast routing information.

IP rcIpMrouteHwSourcesSubnet

1.3.6.1.4.1.2272.1.8.24.3.1.2

IpAddress

read-only

The network address from where the source is sending the stream of traffic for which this entry contains multicast routing information.

RCV rcIpMrouteHwSourcesInvlan

1.3.6.1.4.1.2272.1.8.24.3.1.3

RcVlanIdOrNone

read-only

The Ingress vlan Id from where the traffic is coming for which this entry contains multicast routing information.

IP rcIpMrouteHwSourcesAddress

1.3.6.1.4.1.2272.1.8.24.3.1.4

IpAddress

read-only

The Source Address from where the stream of traffic is reaching the corresponding Group Address for which this entry contains multicast routing information.

POR rcIpMrouteHwSourcesIngressPort

1.3.6.1.4.1.2272.1.8.24.3.1.5

PortSet

read-only

The Ingress vlan ports from where the traffic is coming, for which this entry contains multicast routing information.

rcIpMrouteHwEgressVlansTable

1.3.6.1.4.1.2272.1.8.24.4

not-accessible

The (conceptual) table containing egress vlan entries of multicast routing information for the Group Address.

rcIpMrouteHwEgressVlansEntry

1.3.6.1.4.1.2272.1.8.24.4.1

not-accessible

An entry (conceptual row) containing egress vlan entries of multicast routing information for a particular Group Address.

IP rcIpMrouteHwEgressVlansGroupAddress

1.3.6.1.4.1.2272.1.8.24.4.1.1

IpAddress

read-only

The IP multicast group address for which this entry contains multicast routing information.

IP rcIpMrouteHwEgressVlansSubnet

1.3.6.1.4.1.2272.1.8.24.4.1.2

IpAddress

read-only

The network address from where the source is sending the stream of traffic for which this entry contains multicast routing information.

RCV rcIpMrouteHwEgressVlansInvlan

1.3.6.1.4.1.2272.1.8.24.4.1.3

RcVlanIdOrNone

read-only

The Ingress vlan Id from where the traffic is coming for which this entry contains multicast routing information.

RCV rcIpMrouteHwEgressVlansId

1.3.6.1.4.1.2272.1.8.24.4.1.4

RcVlanIdOrNone

read-only

The Egress vlan Id from where the traffic is going out for which this entry contains multicast routing information

POR rcIpMrouteHwEgressVlansPorts

1.3.6.1.4.1.2272.1.8.24.4.1.5

PortSet

read-only

he Egress vlan ports from where the traffic is going out for which this entry contains multicast routing information.

I32 rcIpMrouteHwEgressVlansIndex

1.3.6.1.4.1.2272.1.8.24.4.1.6

Integer32

read-only

This Index value keep tracks of the hardware record that has been accessed for displaying the entry containing multicast routing information.

rcIpResourceUsage

1.3.6.1.4.1.2272.1.8.25

rcIpResourceUsageGlobal

1.3.6.1.4.1.2272.1.8.25.1

INT rcIpResourceUsageGlobalIngressRecInUse

1.3.6.1.4.1.2272.1.8.25.1.1

INTEGER

read-only

Used to get the Ingress Record Usage in the switch. (S-G usage).

INT rcIpResourceUsageGlobalEgressRecInUse

1.3.6.1.4.1.2272.1.8.25.1.2

INTEGER

read-only

Used to get the Egress Record Usage in the switch (pepstream count).

INT rcIpResourceUsageGlobalIngressThreshold

1.3.6.1.4.1.2272.1.8.25.1.3

INTEGER

read-write

Used to get the threshold count for Ingress records.

INT rcIpResourceUsageGlobalEgressThreshold

1.3.6.1.4.1.2272.1.8.25.1.4

INTEGER

read-write

Used to get threshold count for egress records.

ENA rcIpResourceUsageGlobalSendTrapAndLog

1.3.6.1.4.1.2272.1.8.25.1.5

EnableValue

read-write

A means of alerting the user. If this bool is set, a message will be send to console and also a duReport will be logged.

ENA rcIpResourceUsageGlobalSendTrapOnly

1.3.6.1.4.1.2272.1.8.25.1.6

EnableValue

read-write

A means of alerting the user. If this bool is set, a message will be send to console.

ENA rcIpResourceUsageGlobalLogMsgOnly

1.3.6.1.4.1.2272.1.8.25.1.7

EnableValue

read-write

A means of alerting the user.If this bool is set, a duReport will be logged.

rcIpRsmlt

1.3.6.1.4.1.2272.1.8.26

rcIpRsmltGlobal

1.3.6.1.4.1.2272.1.8.26.1

T/F rcIpRsmltEdgeSupportEnable

1.3.6.1.4.1.2272.1.8.26.1.2

TruthValue

read-write

Used to enable/disable RSMLT Edge Support feature

rcIpRsmltOperTable

1.3.6.1.4.1.2272.1.8.26.2

not-accessible

Route Smlt Table

rcIpRsmltOperEntry

1.3.6.1.4.1.2272.1.8.26.2.1

not-accessible

An entry of Ip As Path Access List Table.

NUM rcIpRsmltOperIfIndex

1.3.6.1.4.1.2272.1.8.26.2.1.1

InterfaceIndex

read-only

Route Smlt Oper IfIndex.

T/F rcIpRsmltOperAdminStatus

1.3.6.1.4.1.2272.1.8.26.2.1.2

TruthValue

read-write

is a enable/disable flag.

INT rcIpRsmltOperHoldDownTimer

1.3.6.1.4.1.2272.1.8.26.2.1.3

INTEGER

read-write

Timer value, the range of value is from 0 to 3600.

INT rcIpRsmltOperHoldDownTimeRemaining

1.3.6.1.4.1.2272.1.8.26.2.1.4

INTEGER

read-only

The time value that indicate how much time remaining of HoldDownTimer.

INT rcIpRsmltOperHoldUpTimer

1.3.6.1.4.1.2272.1.8.26.2.1.5

INTEGER

read-write

The range of value 0 to 3600 or 9999. 9999 means infinity.

INT rcIpRsmltOperHoldUpTimeRemaining

1.3.6.1.4.1.2272.1.8.26.2.1.6

INTEGER

read-only

The time value that indicate how much time remaining of HoldUpTimer.

IP rcIpRsmltOperIpAddr

1.3.6.1.4.1.2272.1.8.26.2.1.7

IpAddress

read-only

IP Interface with RSMLT on.

INT rcIpRsmltOperOperStatus

1.3.6.1.4.1.2272.1.8.26.2.1.8

INTEGER

read-only

The operation status of Rsmlt, up or down.

IDL rcIpRsmltOperSmltId

1.3.6.1.4.1.2272.1.8.26.2.1.9

IdList

read-only

The id range for SMLT is 1-32.

INT rcIpRsmltOperVlanId

1.3.6.1.4.1.2272.1.8.26.2.1.11

INTEGER

read-only

Vlan id.

MAC rcIpRsmltOperMacAddr

1.3.6.1.4.1.2272.1.8.26.2.1.12

MacAddress

read-only

Mac Address.

ROW rcIpRsmltOperRowStatus

1.3.6.1.4.1.2272.1.8.26.2.1.13

RowStatus

read-write

Row Status.

OID rcIpRsmltOperVrfId

1.3.6.1.4.1.2272.1.8.26.2.1.14

VrfIdentifier

read-only

Indicates the Virtual Router to which the RSMLT Oper instance belongs.

STR rcIpRsmltOperVrfName

1.3.6.1.4.1.2272.1.8.26.2.1.15

SnmpAdminString

read-only

Name of the Virtual Router to which the RSMLT Oper instance belongs.

rcIpRsmltPeerTable

1.3.6.1.4.1.2272.1.8.26.3

not-accessible

Route Smlt Table

rcIpRsmltPeerEntry

1.3.6.1.4.1.2272.1.8.26.3.1

not-accessible

An entry of Ip As Path Access List Table.

NUM rcIpRsmltPeerIfIndex

1.3.6.1.4.1.2272.1.8.26.3.1.1

InterfaceIndex

read-only

Route Smlt Oper IfIndex.

T/F rcIpRsmltPeerAdminStatus

1.3.6.1.4.1.2272.1.8.26.3.1.2

TruthValue

read-only

is a enable/disable flag.

INT rcIpRsmltPeerHoldDownTimer

1.3.6.1.4.1.2272.1.8.26.3.1.3

INTEGER

read-only

Timer value, the range of value is from 0 to 3600.

INT rcIpRsmltPeerHoldDownTimeRemaining

1.3.6.1.4.1.2272.1.8.26.3.1.4

INTEGER

read-only

The time value that indicate how much time remaining of HoldDownTimer.

INT rcIpRsmltPeerHoldUpTimer

1.3.6.1.4.1.2272.1.8.26.3.1.5

INTEGER

read-only

The range of value 0 to 3600 or 9999. 9999 means infinity.

INT rcIpRsmltPeerHoldUpTimeRemaining

1.3.6.1.4.1.2272.1.8.26.3.1.6

INTEGER

read-only

The time value that indicate how much time remaining of HoldUpTimer.

IP rcIpRsmltPeerIpAddr

1.3.6.1.4.1.2272.1.8.26.3.1.7

IpAddress

read-only

IP Interface with RSMLT on.

INT rcIpRsmltPeerOperStatus

1.3.6.1.4.1.2272.1.8.26.3.1.8

INTEGER

read-only

The operation status of Rsmlt, up or down.

IDL rcIpRsmltPeerSmltId

1.3.6.1.4.1.2272.1.8.26.3.1.9

IdList

read-only

The id range for SMLT is 1-32.

INT rcIpRsmltPeerVlanId

1.3.6.1.4.1.2272.1.8.26.3.1.11

INTEGER

read-only

Vlan id.

MAC rcIpRsmltPeerMacAddr

1.3.6.1.4.1.2272.1.8.26.3.1.12

MacAddress

read-only

Mac Address.

OID rcIpRsmltPeerVrfId

1.3.6.1.4.1.2272.1.8.26.3.1.13

VrfIdentifier

read-only

Indicates the Virtual Router to which the RSMLT Peer instance belongs.

STR rcIpRsmltPeerVrfName

1.3.6.1.4.1.2272.1.8.26.3.1.14

SnmpAdminString

read-only

Name of the Virtual Router to which the RSMLT Peer instance belongs.

rcIpRsmltEdgePeerTable

1.3.6.1.4.1.2272.1.8.26.4

not-accessible

RSMLT Edge Support Peer Info table. This table consists of the RSMLT Peers for which the switch will act as a PeerForwarder.

rcIpRsmltEdgePeerEntry

1.3.6.1.4.1.2272.1.8.26.4.1

not-accessible

RSMLT Edge Support Peer Info Entry

RCV rcIpRsmltEdgeVlanId

1.3.6.1.4.1.2272.1.8.26.4.1.1

RcVlanIdOrNone

not-accessible

A value that uniquely identifies the Virtual LAN associated with this entry.

IP rcIpRsmltEdgePeerIpAddress

1.3.6.1.4.1.2272.1.8.26.4.1.2

IpAddress

read-only

IP address of the Peer RSMLT Interface.

MAC rcIpRsmltEdgePeerMacAddress

1.3.6.1.4.1.2272.1.8.26.4.1.3

MacAddress

read-only

The MAC address of the Peer RSMLT interface.

OID rcIpRsmltEdgePeerVrfId

1.3.6.1.4.1.2272.1.8.26.4.1.4

VrfIdentifier

read-only

Indicates the Virtual Router to which the RSMLT Edge Peer instance belongs.

STR rcIpRsmltEdgePeerVrfName

1.3.6.1.4.1.2272.1.8.26.4.1.5

SnmpAdminString

read-only

Name of the Virtual Router to which the RSMLT Edge Peer instance belongs.

rcIpv6RsmltOperTable

1.3.6.1.4.1.2272.1.8.26.5

not-accessible

Route Smlt Table

rcIpv6RsmltOperEntry

1.3.6.1.4.1.2272.1.8.26.5.1

not-accessible

A local IPv6 RSMLT entry

NUM rcIpv6RsmltOperIfIndex

1.3.6.1.4.1.2272.1.8.26.5.1.1

InterfaceIndex

not-accessible

Route Smlt Oper IfIndex.

ADR rcIpv6RsmltOperIpv6Addr

1.3.6.1.4.1.2272.1.8.26.5.1.2

Ipv6Address

not-accessible

IPv6 Interface with RSMLT on.

I32 rcIpv6RsmltOperIpv6PrefixLength

1.3.6.1.4.1.2272.1.8.26.5.1.3

Integer32

not-accessible

IPv6 Prefix Length.

T/F rcIpv6RsmltOperAdminStatus

1.3.6.1.4.1.2272.1.8.26.5.1.4

TruthValue

read-write

is a enable/disable flag.

I32 rcIpv6RsmltOperHoldDownTimer

1.3.6.1.4.1.2272.1.8.26.5.1.5

Integer32

read-write

Timer value, the range of value is from 0 to 3600.

I32 rcIpv6RsmltOperHoldUpTimer

1.3.6.1.4.1.2272.1.8.26.5.1.7

Integer32

read-write

The range of value 0 to 3600 or 9999. 9999 means infinity.

INT rcIpv6RsmltOperOperStatus

1.3.6.1.4.1.2272.1.8.26.5.1.9

INTEGER

read-only

The operation status of Rsmlt, up or down.

IDL rcIpv6RsmltOperSmltId

1.3.6.1.4.1.2272.1.8.26.5.1.10

IdList

read-only

The id range for SMLT is 1-32.

I32 rcIpv6RsmltOperVlanId

1.3.6.1.4.1.2272.1.8.26.5.1.12

Integer32

read-only

Vlan id.

MAC rcIpv6RsmltOperMacAddr

1.3.6.1.4.1.2272.1.8.26.5.1.13

MacAddress

read-only

Mac Address.

OID rcIpv6RsmltOperVrfId

1.3.6.1.4.1.2272.1.8.26.5.1.14

VrfIdentifier

read-only

Indicates the Virtual Router to which the RSMLT Oper instance belongs.

STR rcIpv6RsmltOperVrfName

1.3.6.1.4.1.2272.1.8.26.5.1.15

SnmpAdminString

read-only

Name of the Virtual Router to which the RSMLT Oper instance belongs.

rcIpv6RsmltPeerTable

1.3.6.1.4.1.2272.1.8.26.6

not-accessible

Route Smlt Peer Table

rcIpv6RsmltPeerEntry

1.3.6.1.4.1.2272.1.8.26.6.1

not-accessible

An entry of Ip As Path Access List Table.

NUM rcIpv6RsmltPeerIfIndex

1.3.6.1.4.1.2272.1.8.26.6.1.1

InterfaceIndex

not-accessible

Route Smlt Oper IfIndex.

ADR rcIpv6RsmltPeerIpv6Addr

1.3.6.1.4.1.2272.1.8.26.6.1.2

Ipv6Address

not-accessible

IP Interface with RSMLT on.

I32 rcIpv6RsmltPeerIpv6PrefixLength

1.3.6.1.4.1.2272.1.8.26.6.1.3

Integer32

not-accessible

IPv6 Prefix Length

T/F rcIpv6RsmltPeerAdminStatus

1.3.6.1.4.1.2272.1.8.26.6.1.4

TruthValue

read-only

is a enable/disable flag.

I32 rcIpv6RsmltPeerHoldDownTimer

1.3.6.1.4.1.2272.1.8.26.6.1.5

Integer32

read-only

Timer value, the range of value is from 0 to 3600.

I32 rcIpv6RsmltPeerHoldDownTimeRemaining

1.3.6.1.4.1.2272.1.8.26.6.1.6

Integer32

read-only

The time value that indicate how much time remaining of HoldDownTimer.

I32 rcIpv6RsmltPeerHoldUpTimer

1.3.6.1.4.1.2272.1.8.26.6.1.7

Integer32

read-only

The range of value 0 to 3600 or 9999. 9999 means infinity.

I32 rcIpv6RsmltPeerHoldUpTimeRemaining

1.3.6.1.4.1.2272.1.8.26.6.1.8

Integer32

read-only

The time value that indicate how much time remaining of HoldUpTimer.

INT rcIpv6RsmltPeerOperStatus

1.3.6.1.4.1.2272.1.8.26.6.1.9

INTEGER

read-only

The operation status of Rsmlt, up or down.

IDL rcIpv6RsmltPeerSmltId

1.3.6.1.4.1.2272.1.8.26.6.1.10

IdList

read-only

The id range for SMLT is 1-32.

I32 rcIpv6RsmltPeerVlanId

1.3.6.1.4.1.2272.1.8.26.6.1.12

Integer32

read-only

Vlan id.

MAC rcIpv6RsmltPeerMacAddr

1.3.6.1.4.1.2272.1.8.26.6.1.13

MacAddress

read-only

Mac Address.

OID rcIpv6RsmltPeerVrfId

1.3.6.1.4.1.2272.1.8.26.6.1.14

VrfIdentifier

read-only

Indicates the Virtual Router to which the RSMLT Peer instance belongs.

STR rcIpv6RsmltPeerVrfName

1.3.6.1.4.1.2272.1.8.26.6.1.15

SnmpAdminString

read-only

Name of the Virtual Router to which the RSMLT Peer instance belongs.

rcIpv6RsmltEdgePeerTable

1.3.6.1.4.1.2272.1.8.26.7

not-accessible

RSMLT Edge Support Peer Info table. This table consists of the RSMLT Peers for which the switch will act as a PeerForwarder.

rcIpv6RsmltEdgePeerEntry

1.3.6.1.4.1.2272.1.8.26.7.1

not-accessible

RSMLT Edge Support Peer Info Entry

I32 rcIpv6RsmltEdgePeerVlanId

1.3.6.1.4.1.2272.1.8.26.7.1.1

Integer32

not-accessible

A value that uniquely identifies the Virtual LAN associated with this entry.

ADR rcIpv6RsmltEdgePeerIpv6Address

1.3.6.1.4.1.2272.1.8.26.7.1.2

Ipv6Address

not-accessible

IP address of the Peer RSMLT Interface.

I32 rcIpv6RsmltEdgePeerIpv6PrefixLength

1.3.6.1.4.1.2272.1.8.26.7.1.3

Integer32

not-accessible

If set then this prefix can be used for address autoconfig, passed opaquely to Infinity

MAC rcIpv6RsmltEdgePeerMacAddress

1.3.6.1.4.1.2272.1.8.26.7.1.4

MacAddress

read-only

The MAC address of the Peer RSMLT interface.

rcIpDhcpOp82StatsTable

1.3.6.1.4.1.2272.1.8.29

not-accessible

DHCP statistics table for Relay Agent Information Option

rcIpDhcpOp82StatsEntry

1.3.6.1.4.1.2272.1.8.29.1

not-accessible

Used to see current statistics on interfaces that have DHCP Option 82 (Relay Agent Information) enabled. This table is read-only.

NUM rcIpDhcpOp82StatsIfIndex

1.3.6.1.4.1.2272.1.8.29.1.1

InterfaceIndexOrZero

not-accessible

Interface number. The number can represent either a physical or logical(VLAN) interface.

C32 rcIpDhcpOp82StatsFoundOp82

1.3.6.1.4.1.2272.1.8.29.1.2

Counter32

read-only

Represents the number of packets received on the interface that already had Dhcp Option 82 inserted in them

C32 rcIpDhcpOp82StatsDropped

1.3.6.1.4.1.2272.1.8.29.1.3

Counter32

read-only

Represents the number of packets dropped because of reasons related to Dhcp Option 82. These reasons could be that the packet was received from an untrusted source or spoofing was detected.

INT rcIpDhcpOp82StatsCircuitId

1.3.6.1.4.1.2272.1.8.29.1.4

INTEGER

read-only

Represents the value of CircuitId inserted in the packets. This is the Port number of the Dhcp Relay.

C32 rcIpDhcpOp82StatsAddedCircuitId

1.3.6.1.4.1.2272.1.8.29.1.5

Counter32

read-only

Represents the number of packets which had CircuitId inserted on this interface

C32 rcIpDhcpOp82StatsRemovedCircuitId

1.3.6.1.4.1.2272.1.8.29.1.6

Counter32

read-only

Represents the number of packets which had CircuitId removed on this interface

MAC rcIpDhcpOp82StatsRemoteId

1.3.6.1.4.1.2272.1.8.29.1.7

MacAddress

read-only

Represents the value of RemoteId inserted in the packets. This is the Mac address of the Dhcp Relay.

C32 rcIpDhcpOp82StatsAddedRemoteId

1.3.6.1.4.1.2272.1.8.29.1.8

Counter32

read-only

Represents the number of packets which had RemoteId inserted on this interface

C32 rcIpDhcpOp82StatsRemovedRemoteId

1.3.6.1.4.1.2272.1.8.29.1.9

Counter32

read-only

Represents the number of packets which had RemoteId removed on this interface

IP rcIpDhcpOp82StatsAgentAddr

1.3.6.1.4.1.2272.1.8.29.1.10

IpAddress

read-only

The IP address configured as relay on this interface; it is either the IP of the physical interface or the IP of the VRRP address

rcIpGenPolicy

1.3.6.1.4.1.2272.1.8.100

I32 rcIpAsPathAccessListTableSize

1.3.6.1.4.1.2272.1.8.100.1

Integer32

read-only

table size

rcIpAsPathAccessListTable

1.3.6.1.4.1.2272.1.8.100.2

not-accessible

IP As Path Access List table

rcIpAsPathAccessListEntry

1.3.6.1.4.1.2272.1.8.100.2.1

not-accessible

An entry of Ip As Path Access List Table.

INT rcIpAsPathAccessListId

1.3.6.1.4.1.2272.1.8.100.2.1.1

INTEGER

read-only

Path Access List entry Id.

INT rcIpAsPathAccessListMemberId

1.3.6.1.4.1.2272.1.8.100.2.1.2

INTEGER

read-only

frq. at which hello sent.

INT rcIpAsPathAccessListMode

1.3.6.1.4.1.2272.1.8.100.2.1.3

INTEGER

read-write

Path Access List Mode, permit or deny.

OCT rcIpAsPathAccessListAsRegularExpression

1.3.6.1.4.1.2272.1.8.100.2.1.4

OCTET STRING

read-write

IP Path Access List Regular Expression

ROW rcIpAsPathAccessListRowStatus

1.3.6.1.4.1.2272.1.8.100.2.1.5

RowStatus

read-write

Table row status.

I32 rcIpCommunityAccessListTableSize

1.3.6.1.4.1.2272.1.8.100.3

Integer32

read-only

table size

rcIpCommunityAccessListTable

1.3.6.1.4.1.2272.1.8.100.4

not-accessible

IP CommunityAccess List table

rcIpCommunityAccessListEntry

1.3.6.1.4.1.2272.1.8.100.4.1

not-accessible

An entry of Ip CommunityAccess List Table.

INT rcIpCommunityAccessListId

1.3.6.1.4.1.2272.1.8.100.4.1.1

INTEGER

read-only

IP CommunityAccess entry List Id

INT rcIpCommunityAccessListMemberId

1.3.6.1.4.1.2272.1.8.100.4.1.2

INTEGER

read-only

frq. at which hello sent.

INT rcIpCommunityAccessListMode

1.3.6.1.4.1.2272.1.8.100.4.1.3

INTEGER

read-write

IP Community Access List Mode, permit or deny.

OCT rcIpCommunityAccessListCommunity

1.3.6.1.4.1.2272.1.8.100.4.1.4

OCTET STRING

read-write

IP Community Access List Community string.

ROW rcIpCommunityAccessListRowStatus

1.3.6.1.4.1.2272.1.8.100.4.1.5

RowStatus

read-write

IP Community Access Table Row Status.

I32 rcIpAccessListTableSize

1.3.6.1.4.1.2272.1.8.100.5

Integer32

read-only

table size

rcIpAccessListTable

1.3.6.1.4.1.2272.1.8.100.6

not-accessible

IP Access List table

rcIpAccessListEntry

1.3.6.1.4.1.2272.1.8.100.6.1

not-accessible

An entry of Ip Access List Table.

INT rcIpAccessListId

1.3.6.1.4.1.2272.1.8.100.6.1.1

INTEGER

read-only

INT rcIpAccessListMode

1.3.6.1.4.1.2272.1.8.100.6.1.2

INTEGER

read-only

IP rcIpAccessListNetwork

1.3.6.1.4.1.2272.1.8.100.6.1.3

IpAddress

read-write

IP rcIpAccessListNetworkMask

1.3.6.1.4.1.2272.1.8.100.6.1.4

IpAddress

read-write

STR rcIpAccessListName

1.3.6.1.4.1.2272.1.8.100.6.1.5

DisplayString

read-write

ROW rcIpAccessListRowStatus

1.3.6.1.4.1.2272.1.8.100.6.1.6

RowStatus

read-write

I32 rcIpExtendedAccessListTableSize

1.3.6.1.4.1.2272.1.8.100.7

Integer32

read-only

table size

rcIpExtendedAccessListTable

1.3.6.1.4.1.2272.1.8.100.8

not-accessible

IP Extended Access List table

rcIpExtendedAccessListEntry

1.3.6.1.4.1.2272.1.8.100.8.1

not-accessible

An entry of Ip Extended Access List Table.

INT rcIpExtendedAccessListId

1.3.6.1.4.1.2272.1.8.100.8.1.1

INTEGER

read-only

INT rcIpExtendedAccessListMode

1.3.6.1.4.1.2272.1.8.100.8.1.2

INTEGER

read-only

IP rcIpExtendedAccessListNetwork

1.3.6.1.4.1.2272.1.8.100.8.1.3

IpAddress

read-only

IP rcIpExtendedAccessListNetworkWildCard

1.3.6.1.4.1.2272.1.8.100.8.1.4

IpAddress

read-only

IP rcIpExtendedAccessListNetworkMask

1.3.6.1.4.1.2272.1.8.100.8.1.5

IpAddress

read-only

IP rcIpExtendedAccessListNetworkMaskWildCard

1.3.6.1.4.1.2272.1.8.100.8.1.6

IpAddress

read-only

STR rcIpExtendedAccessListName

1.3.6.1.4.1.2272.1.8.100.8.1.7

DisplayString

read-write

ROW rcIpExtendedAccessListRowStatus

1.3.6.1.4.1.2272.1.8.100.8.1.8

RowStatus

read-write

I32 rcIpPrefixListTableSize

1.3.6.1.4.1.2272.1.8.100.9

Integer32

read-only

table size

rcIpPrefixListTable

1.3.6.1.4.1.2272.1.8.100.10

not-accessible

IP Prefix List table

rcIpPrefixListEntry

1.3.6.1.4.1.2272.1.8.100.10.1

not-accessible

An entry of Ip Prefix List Table.

I32 rcIpPrefixListId

1.3.6.1.4.1.2272.1.8.100.10.1.1

Integer32

read-only

ListId

IP rcIpPrefixListPrefix

1.3.6.1.4.1.2272.1.8.100.10.1.2

IpAddress

read-only

Is a member of a specific prefix list. Adding the prefix to the given prefix list

INT rcIpPrefixListPrefixMaskLen

1.3.6.1.4.1.2272.1.8.100.10.1.3

INTEGER

read-only

prefix mask length

INT rcIpPrefixListMaskLenFrom

1.3.6.1.4.1.2272.1.8.100.10.1.4

INTEGER

read-write

used with mask len

INT rcIpPrefixListMaskLenUpto

1.3.6.1.4.1.2272.1.8.100.10.1.5

INTEGER

read-write

used with mask len

STR rcIpPrefixListName

1.3.6.1.4.1.2272.1.8.100.10.1.6

DisplayString

read-write

list name

ROW rcIpPrefixListRowStatus

1.3.6.1.4.1.2272.1.8.100.10.1.7

RowStatus

read-write

row status

I32 rcIpRoutePolicyTableSize

1.3.6.1.4.1.2272.1.8.100.11

Integer32

read-only

table size

T/F rcIpRoutePolicyApply

1.3.6.1.4.1.2272.1.8.100.12

TruthValue

read-write

rcIpRoutePolicyTable

1.3.6.1.4.1.2272.1.8.100.13

not-accessible

IP Route Map table

rcIpRoutePolicyEntry

1.3.6.1.4.1.2272.1.8.100.13.1

not-accessible

An entry of Ip Route Map Table.

I32 rcIpRoutePolicyId

1.3.6.1.4.1.2272.1.8.100.13.1.1

Integer32

read-only

Index used to identify a group of policies in the route policy tableRoute map id

I32 rcIpRoutePolicySequenceNumber

1.3.6.1.4.1.2272.1.8.100.13.1.2

Integer32

read-only

second index used to identify a specific policy with in the route policy group (grouped by Id). This field allows users to specify different MATCH, SET parameters and an action.

STR rcIpRoutePolicyName

1.3.6.1.4.1.2272.1.8.100.13.1.3

DisplayString

read-write

Is used to group a set of policies with different sequence number. Id & Name have one-on-one relationship. Different policy groups can contain same sequence number, whereas with in a group the sequence number must be different.

T/F rcIpRoutePolicyEnable

1.3.6.1.4.1.2272.1.8.100.13.1.4

TruthValue

read-write

Value specified here indicate whether this policy is enabled or not. If disabled policy sould not be used.

INT rcIpRoutePolicyMode

1.3.6.1.4.1.2272.1.8.100.13.1.5

INTEGER

read-write

specifies the action to be taken when this policy is selected for a specific route. This can be permit or deny or continue. Permit indicates allow the route, deny indicates ignore the route. Continue means continue checking the next match criteria set in the next policy seq, if none take the default action in the given context.

INT rcIpRoutePolicyMatchProtocol

1.3.6.1.4.1.2272.1.8.100.13.1.6

INTEGER

read-write

Match protocol. Used for RIP and DVMRP announce policy only. Value is one of multiple (logical 'OR) of the following values: direct(1), static(2), rip(4), ospf(8), ebgp(16), dvmrp(32), ibgp(64), isis(128), any(255) direct(1): enables direct match-protocol static(2): enables static match-protocol rip(4): enables rip match-protocol ospf(8): enables ospf match-protocol ebgp(16): enables ebgp match-protocol dvmrp(32): enables dvmrp match-protocol ibgp(64): enables ibgp match-protocol isis(128): enables isis match-protocol any(255): enables all match-protocols

STR rcIpRoutePolicyMatchAsPath

1.3.6.1.4.1.2272.1.8.100.13.1.7

DisplayString

read-write

Applicable to BGP protocol only. Match the BGP autonomous system path. This will override the BGP neighbor filter list info.

STR rcIpRoutePolicyMatchCommunity

1.3.6.1.4.1.2272.1.8.100.13.1.8

DisplayString

read-write

Applicable to BGP protocol only. Filter incoming/outgoing updates based on communities.

ENA rcIpRoutePolicyMatchCommunityExact

1.3.6.1.4.1.2272.1.8.100.13.1.9

EnableValue

read-write

If enabled indicates the match has be an exact (i.e., all of the communities specified in the path has to be matched).

STR rcIpRoutePolicyMatchNetwork

1.3.6.1.4.1.2272.1.8.100.13.1.10

RcLongDisplayString

read-write

can specify one or more prefix list name or id(s)

STR rcIpRoutePolicyMatchIpRouteSource

1.3.6.1.4.1.2272.1.8.100.13.1.11

RcLongDisplayString

read-write

In case of Rip routes this is equivalent to RipInterface. In case of DVMRP routes this is equivalent to DVMRP gateway. Can specify one or more prefix list name(s) or id(s) seperated by comma.

STR rcIpRoutePolicyMatchNextHop

1.3.6.1.4.1.2272.1.8.100.13.1.12

RcLongDisplayString

read-write

In case of Rip routes this is equivalent to RipInterface. In case of DVMRP routes this is equivalent to DVMRP gateway. Can specify one or more prefix list name(s) or id(s) seperated by comma.

STR rcIpRoutePolicyMatchInterface

1.3.6.1.4.1.2272.1.8.100.13.1.13

RcLongDisplayString

read-write

Match received interface. Only for rip routes. Ignored in all other cases.

INT rcIpRoutePolicyMatchRouteType

1.3.6.1.4.1.2272.1.8.100.13.1.14

INTEGER

read-write

For BGP this choice refers to locally generated routes external routes learned via ebgp nbr. For OSPF internal refers to intra and inter area routes (belongs to local autonomous system). External (type1|type2) refers to the routes learned from other ASs and imported as either type1 or type2. if type1/type2 is specified then match only type1/type2.

INT rcIpRoutePolicyMatchMetric

1.3.6.1.4.1.2272.1.8.100.13.1.15

INTEGER

read-write

Match mec field in the incoming advertisement.

STR rcIpRoutePolicyMatchTag

1.3.6.1.4.1.2272.1.8.100.13.1.16

DisplayString

read-write

specifies a list of tag(s), that will be used during the match criteria process.contains one or more tag values..

INT rcIpRoutePolicySetRoutePreference

1.3.6.1.4.1.2272.1.8.100.13.1.17

INTEGER

read-write

if non-zero specifies the route preference value to be assigned to the routes that applies this policy.contains one or more tag values..

STR rcIpRoutePolicySetAsPath

1.3.6.1.4.1.2272.1.8.100.13.1.18

DisplayString

read-write

The AS path vaule to be used whether the SetAsPathMode is Tag or Prepend.as-path string..

INT rcIpRoutePolicySetAsPathMode

1.3.6.1.4.1.2272.1.8.100.13.1.19

INTEGER

read-write

It can be either tag or prepend tag. applicable only while redistributing routes to BGP.Converts the tag of a route into AS path.

ENA rcIpRoutePolicySetAutomaticTag

1.3.6.1.4.1.2272.1.8.100.13.1.20

EnableValue

read-write

STR rcIpRoutePolicySetCommunityNumber

1.3.6.1.4.1.2272.1.8.100.13.1.21

DisplayString

read-write

this value can be a number (1..42949672000) or no-export or no-advertise. Applicable to BGP advertisments.community number.

INT rcIpRoutePolicySetCommunityMode

1.3.6.1.4.1.2272.1.8.100.13.1.22

INTEGER

read-write

this value can be either append or none unchanged - keep the community attribute in the route path as it is. none - remove the community in the route path additive - adds the community-number specified in SetCommunityNumber to the community list attribute. Applicable to BGP advertisments.

I32 rcIpRoutePolicySetMetricTypeInternal

1.3.6.1.4.1.2272.1.8.100.13.1.23

Integer32

read-write

Indicates to set the MED value for routes advertised to ebgp nbrs to the IGP metric value.

INT rcIpRoutePolicySetMetric

1.3.6.1.4.1.2272.1.8.100.13.1.24

INTEGER

read-write

Value of the metric to be used while sending an update for the routes that match the matching criteria in this route policy. Default - 0 indicates the internal value defined for protocol

INT rcIpRoutePolicySetMetricType

1.3.6.1.4.1.2272.1.8.100.13.1.25

INTEGER

read-write

Metric type for the routes to be imported into OSPF routing protocol, which passed the matching criteria configured in this route policy.

IP rcIpRoutePolicySetNextHop

1.3.6.1.4.1.2272.1.8.100.13.1.26

IpAddress

read-write

IpAddress of the next hop router. Ignored for DVMRP routes.

INT rcIpRoutePolicySetOrigin

1.3.6.1.4.1.2272.1.8.100.13.1.27

INTEGER

read-write

igp/egp/incomplete Applicable to BGP protocol only. If not set uses the route origin from the Ip routing table (protocol).

I32 rcIpRoutePolicySetLocalPref

1.3.6.1.4.1.2272.1.8.100.13.1.28

Integer32

read-write

this value will be used during route decision process in the BGP protocol. Applicable to BGP only.

I32 rcIpRoutePolicySetOriginEgpAs

1.3.6.1.4.1.2272.1.8.100.13.1.29

Integer32

read-write

indicates the Remote autonomous sys number. Applicable to BGP only.

I32 rcIpRoutePolicySetTag

1.3.6.1.4.1.2272.1.8.100.13.1.30

Integer32

read-write

Value to be used for setting tag of the destination routing protocol. If not specified forward the tag value in the source routing protocol. Value 0 indicates not set

I32 rcIpRoutePolicySetWeight

1.3.6.1.4.1.2272.1.8.100.13.1.31

Integer32

read-write

Should be using with match as-path condition. Weight value for the routing table. For BGP this value will override the weight configured through NetworkTableEntry or FilterListWeight or NeighborWeight. Used for BGP only.Value 0 indicates not set

STR rcIpRoutePolicySetInjectNetList

1.3.6.1.4.1.2272.1.8.100.13.1.32

DisplayString

read-write

specifies the prefix list to be used either for injecting the routes into the routing table or to include the networks in the advertisement. Ignored for DVMRP.

ROW rcIpRoutePolicyRowStatus

1.3.6.1.4.1.2272.1.8.100.13.1.33

RowStatus

read-write

row status

IP rcIpRoutePolicySetMask

1.3.6.1.4.1.2272.1.8.100.13.1.34

IpAddress

read-write

Set Mask Ip Address

ENA rcIpRoutePolicyNssaPbit

1.3.6.1.4.1.2272.1.8.100.13.1.35

EnableValue

read-write

Set/Reset P bit in specified type 7 LSA. By default P bit is always set in case user set it to disable state for particular route policy than all type 7 LSAs associated with that route policy will have P bit cleared, with this intact NSSA ABR will not perform translation of these LSAs to type 5.

IDL rcIpRoutePolicyMatchVrf

1.3.6.1.4.1.2272.1.8.100.13.1.36

IdList

read-write

An array used to identify which source VRFs have leaked routes to the local VRF

STR rcIpRoutePolicyMatchExtCommunity

1.3.6.1.4.1.2272.1.8.100.13.1.37

DisplayString

read-create

Filter incoming/outgoing updates based on communities

STR rcIpRoutePolicySetExtCommunity

1.3.6.1.4.1.2272.1.8.100.13.1.38

DisplayString

read-create

Set Extended-community string.

INT rcIpRoutePolicySetExtCommunityMode

1.3.6.1.4.1.2272.1.8.100.13.1.39

INTEGER

read-create

This value can be either additive, unchanged or overwrite.

I32 rcIpRoutePolicyMatchLocalPref

1.3.6.1.4.1.2272.1.8.100.13.1.40

Integer32

read-create

Match Local Prefix value.

STR rcIpRoutePolicyMatchIpRouteDest

1.3.6.1.4.1.2272.1.8.100.13.1.41

RcLongDisplayString

read-create

to match route destination, one can specify one or more prefix list name(s) or id(s) separated by comma.

INT rcIpRoutePolicySetLevel

1.3.6.1.4.1.2272.1.8.100.13.1.42

INTEGER

read-create

Level of the Ip routing policy

ADR rcIpRoutePolicyIpv6SetNextHop

1.3.6.1.4.1.2272.1.8.100.13.1.43

Ipv6Address

read-create

Address of the ipv6 next hop router. Ignored for DVMRP routes.

I32 rcIpRedistributeTableSize

1.3.6.1.4.1.2272.1.8.100.14

Integer32

read-only

table size

I32 rcIpRedistributeTableSize2

1.3.6.1.4.1.2272.1.8.100.14

Integer32

read-only

table size

T/F rcIpRedistributeApply

1.3.6.1.4.1.2272.1.8.100.15

TruthValue

read-write

T/F rcIpRedistributeApply2

1.3.6.1.4.1.2272.1.8.100.15

TruthValue

read-write

rcIpRedistributeTable

1.3.6.1.4.1.2272.1.8.100.16

not-accessible

IP Redistribute table

rcIpRedistributeEntry

1.3.6.1.4.1.2272.1.8.100.16.1

not-accessible

An entry of Ip Redistribute Table.

INT rcIpRedistributeProtocol

1.3.6.1.4.1.2272.1.8.100.16.1.1

INTEGER

read-only

Protocol is any one of the dynamic routing protocol, which is interested in receiving the external routing info.

INT rcIpRedistributeRouteSource

1.3.6.1.4.1.2272.1.8.100.16.1.2

INTEGER

read-only

equivalent to the owner field in the routing table. This field indicates that the protocol is interested in knowing/not-knowing the routes learned from this source.

ENA rcIpRedistributeEnable

1.3.6.1.4.1.2272.1.8.100.16.1.3

EnableValue

read-write

Enable/Disable. By default this is enabled.

INT rcIpRedistributeMetric

1.3.6.1.4.1.2272.1.8.100.16.1.4

INTEGER

read-write

value of the metric to be announced in the advertisment

INT rcIpRedistributeMetricType

1.3.6.1.4.1.2272.1.8.100.16.1.5

INTEGER

read-write

specifies the type of the metric type, useful for OSPF and BGP only.

INT rcIpRedistributeMatchRouteType

1.3.6.1.4.1.2272.1.8.100.16.1.6

INTEGER

read-write

used to filter a route based on the route type. applicable to BGP.

I32 rcIpRedistributeSetTag

1.3.6.1.4.1.2272.1.8.100.16.1.7

Integer32

read-write

Tag value to be set in the advertisment.

INT rcIpRedistributeSubnets

1.3.6.1.4.1.2272.1.8.100.16.1.8

INTEGER

read-write

applicable to OSPF only. Indicates that all the subnets need to be advertised individually.

STR rcIpRedistributeRoutePolicy

1.3.6.1.4.1.2272.1.8.100.16.1.9

DisplayString

read-write

specify the route policy to achieve the final granularity in filtering to determine whether or not a specific route should be advertised to the given protocol.Route map name

I32 rcIpRedistributeASNumber

1.3.6.1.4.1.2272.1.8.100.16.1.10

Integer32

read-write

Autonomous system number. Used only for the BGP protocol.

I32 rcIpRedistributeWeight

1.3.6.1.4.1.2272.1.8.100.16.1.11

Integer32

read-write

used only for the BGP protocol.

I32 rcIpRedistributeDefaultOriginate

1.3.6.1.4.1.2272.1.8.100.16.1.12

Integer32

read-write

indicates the given protocol will originate/advertise a default route.

ROW rcIpRedistributeRowStatus

1.3.6.1.4.1.2272.1.8.100.16.1.13

RowStatus

read-write

row status

I32 rcIpOspfInFilterTableSize

1.3.6.1.4.1.2272.1.8.100.17

Integer32

read-only

table size

T/F rcIpOspfInFilterApply

1.3.6.1.4.1.2272.1.8.100.18

TruthValue

read-write

rcIpOspfInFilterTable

1.3.6.1.4.1.2272.1.8.100.19

not-accessible

IP Ospf In Filter table

rcIpOspfInFilterEntry

1.3.6.1.4.1.2272.1.8.100.19.1

not-accessible

An entry of Ip Ospf In Filter Table.

IP rcIpOspfInFilterAdvertisingRtr

1.3.6.1.4.1.2272.1.8.100.19.1.1

IpAddress

read-only

ENA rcIpOspfInFilterEnable

1.3.6.1.4.1.2272.1.8.100.19.1.2

EnableValue

read-write

IfIndex

INT rcIpOspfInFilterMetricType

1.3.6.1.4.1.2272.1.8.100.19.1.3

INTEGER

read-write

STR rcIpOspfInFilterPolicyName

1.3.6.1.4.1.2272.1.8.100.19.1.4

DisplayString

read-write

ROW rcIpOspfInFilterRowStatus

1.3.6.1.4.1.2272.1.8.100.19.1.5

RowStatus

read-write

I32 rcIpRoutePrefTableSize

1.3.6.1.4.1.2272.1.8.100.20

Integer32

read-only

table size

rcIpRoutePrefTable

1.3.6.1.4.1.2272.1.8.100.21

not-accessible

IP Route Pref table

rcIpRoutePrefEntry

1.3.6.1.4.1.2272.1.8.100.21.1

not-accessible

An entry of Ip Route Pref Table.

INT rcIpRoutePrefProtocol

1.3.6.1.4.1.2272.1.8.100.21.1.1

INTEGER

read-only

Protocol

INT rcIpRoutePrefDefault

1.3.6.1.4.1.2272.1.8.100.21.1.2

INTEGER

read-only

Shows the default preference value for the given protocol.

INT rcIpRoutePrefConfigured

1.3.6.1.4.1.2272.1.8.100.21.1.3

INTEGER

read-write

This value is configurable by the user

rcIpRedistributeInterVrfTable

1.3.6.1.4.1.2272.1.8.100.22

not-accessible

IP Redistribute table for Inter-VRFs

rcIpRedistributeInterVrfEntry

1.3.6.1.4.1.2272.1.8.100.22.1

not-accessible

An entry of Ip Redistribute Table.(new)

OID rcIpRedistributeInterVrfDstVrfId

1.3.6.1.4.1.2272.1.8.100.22.1.1

VrfIdentifier

not-accessible

dst VRF id used in the redistribution

INT rcIpRedistributeInterVrfProtocol

1.3.6.1.4.1.2272.1.8.100.22.1.2

INTEGER

not-accessible

Protocol is any one of the dynamic routing protocol, which is interested in receiving the external routing info.

OID rcIpRedistributeInterVrfSrcVrfId

1.3.6.1.4.1.2272.1.8.100.22.1.3

VrfIdentifier

not-accessible

src VRF id used in the redistribution

INT rcIpRedistributeInterVrfRouteSource

1.3.6.1.4.1.2272.1.8.100.22.1.4

INTEGER

not-accessible

equivalent to the owner field in the routing table. This field indicates that the protocol is interested in knowing/not-knowing the routes learned from this source.

ENA rcIpRedistributeInterVrfEnable

1.3.6.1.4.1.2272.1.8.100.22.1.5

EnableValue

read-write

Enable/Disable. By default this is enabled.

INT rcIpRedistributeInterVrfMetric

1.3.6.1.4.1.2272.1.8.100.22.1.6

INTEGER

read-write

value of the metric to be announced in the advertisment

INT rcIpRedistributeInterVrfMetricType

1.3.6.1.4.1.2272.1.8.100.22.1.7

INTEGER

read-write

specifies the type of the metric type, useful for OSPF and BGP only.

INT rcIpRedistributeInterVrfMatchRouteType

1.3.6.1.4.1.2272.1.8.100.22.1.8

INTEGER

read-write

used to filter a route based on the route type. applicable to BGP.

I32 rcIpRedistributeInterVrfSetTag

1.3.6.1.4.1.2272.1.8.100.22.1.9

Integer32

read-write

Tag value to be set in the advertisment.

INT rcIpRedistributeInterVrfSubnets

1.3.6.1.4.1.2272.1.8.100.22.1.10

INTEGER

read-write

applicable to OSPF only. Indicates that all the subnets need to be advertised individually.

STR rcIpRedistributeInterVrfRoutePolicy

1.3.6.1.4.1.2272.1.8.100.22.1.11

DisplayString

read-write

specify the route policy to achieve the final granularity in filtering to determine whether or not a specific route should be advertised to the given protocol.Route map name

I32 rcIpRedistributeInterVrfASNumber

1.3.6.1.4.1.2272.1.8.100.22.1.12

Integer32

read-write

Autonomous system number. Used only for the BGP protocol.

I32 rcIpRedistributeInterVrfWeight

1.3.6.1.4.1.2272.1.8.100.22.1.13

Integer32

read-write

used only for the BGP protocol.

I32 rcIpRedistributeInterVrfDefaultOriginate

1.3.6.1.4.1.2272.1.8.100.22.1.14

Integer32

read-write

indicates the given protocol will originate/advertise a default route.

ROW rcIpRedistributeInterVrfRowStatus

1.3.6.1.4.1.2272.1.8.100.22.1.15

RowStatus

read-write

row status

I32 rcIpExtCommunityAccessListTableSize

1.3.6.1.4.1.2272.1.8.100.23

Integer32

read-only

IP Extended Community Access List table size.

rcIpExtCommunityAccessListTable

1.3.6.1.4.1.2272.1.8.100.24

not-accessible

IP Extended Community Access List table.

rcIpExtCommunityAccessListEntry

1.3.6.1.4.1.2272.1.8.100.24.1

not-accessible

An entry of Ip Extended Community Access List Table.

INT rcIpExtCommunityAccessListId

1.3.6.1.4.1.2272.1.8.100.24.1.1

INTEGER

not-accessible

IP extended Community Access List Id

INT rcIpExtCommunityAccessListMemberId

1.3.6.1.4.1.2272.1.8.100.24.1.2

INTEGER

not-accessible

Member Id for the extended-community list to be added

INT rcIpExtCommunityAccessListRTType

1.3.6.1.4.1.2272.1.8.100.24.1.3

INTEGER

read-only

The route target Type for IP Extended Community rule in the list

IP rcIpExtCommunityAccessListRTAddress

1.3.6.1.4.1.2272.1.8.100.24.1.4

IpAddress

read-create

Extended community Ip address for the route-target type entry.

INT rcIpExtCommunityAccessListRTAsNumber

1.3.6.1.4.1.2272.1.8.100.24.1.5

INTEGER

read-create

Extended community Asnumber for the route-target type entry.

U32 rcIpExtCommunityAccessListRTAssignedNum

1.3.6.1.4.1.2272.1.8.100.24.1.6

Unsigned32

read-create

Extended community assigned number for the route-target type entry.

INT rcIpExtCommunityAccessListSooType

1.3.6.1.4.1.2272.1.8.100.24.1.7

INTEGER

read-only

The site of origin Type for IP Extended Community Access List

IP rcIpExtCommunityAccessListSooAddress

1.3.6.1.4.1.2272.1.8.100.24.1.8

IpAddress

read-create

Extended community Ip address for the site-of-origin type of entry.

INT rcIpExtCommunityAccessListSooAsNumber

1.3.6.1.4.1.2272.1.8.100.24.1.9

INTEGER

read-create

Extended community AsNumber for the site-of-origin type of entry.

U32 rcIpExtCommunityAccessListSooAssignedNum

1.3.6.1.4.1.2272.1.8.100.24.1.10

Unsigned32

read-create

Extended community assigned number for the site-of-origin type of entry.

OID rcIpExtCommunityAccessListVrfId

1.3.6.1.4.1.2272.1.8.100.24.1.11

VrfIdentifier

read-create

VrfId for the extended-community Access list.

ROW rcIpExtCommunityAccessListRowStatus

1.3.6.1.4.1.2272.1.8.100.24.1.12

RowStatus

read-create

IP Ext Community Table Row Status.

I32 rcIpPrefixListNameTableSize

1.3.6.1.4.1.2272.1.8.100.26

Integer32

read-only

table size

rcIpPrefixListNameTable

1.3.6.1.4.1.2272.1.8.100.27

not-accessible

Prefix List Name table

rcIpPrefixListNameEntry

1.3.6.1.4.1.2272.1.8.100.27.1

not-accessible

An entry of Prefix List Name Table.

I32 rcIpPrefixListNameId

1.3.6.1.4.1.2272.1.8.100.27.1.1

Integer32

not-accessible

list id

STR rcIpPrefixListNameName

1.3.6.1.4.1.2272.1.8.100.27.1.2

DisplayString

read-only

list name

rcIpRoutePolicyNameTable

1.3.6.1.4.1.2272.1.8.100.28

not-accessible

Route Policy Name table for all VRFs

rcIpRoutePolicyNameEntry

1.3.6.1.4.1.2272.1.8.100.28.1

not-accessible

An entry of Route Policy Name Table.

OID rcIpRoutePolicyNameVrfId

1.3.6.1.4.1.2272.1.8.100.28.1.1

VrfIdentifier

not-accessible

route policy vrfId

I32 rcIpRoutePolicyNameId

1.3.6.1.4.1.2272.1.8.100.28.1.2

Integer32

not-accessible

route policy id

STR rcIpRoutePolicyNameName

1.3.6.1.4.1.2272.1.8.100.28.1.3

DisplayString

read-only

route policy name

rcIpBgp

1.3.6.1.4.1.2272.1.8.101

rcIpBgpGeneralGroup

1.3.6.1.4.1.2272.1.8.101.1

I32 rcIpBgpGeneralGroupLocalAs

1.3.6.1.4.1.2272.1.8.101.1.1

Integer32

read-write

Local Autonomous system number

ENA rcIpBgpGeneralGroupAdminStatus

1.3.6.1.4.1.2272.1.8.101.1.2

EnableValue

read-write

Disable or Enable group administrative

I32 rcIpBgpGeneralGroupDefaultMetric

1.3.6.1.4.1.2272.1.8.101.1.3

Integer32

read-write

The default-metric is used in conjunction with the redistribute router configuration command to cause the bgp routing protocol to use this metric as MED

I32 rcIpBgpGeneralGroupDefaultLocalPreference

1.3.6.1.4.1.2272.1.8.101.1.4

Integer32

read-write

Default local preference attribute value to be used

T/F rcIpBgpGeneralGroupDefaultInformationOriginate

1.3.6.1.4.1.2272.1.8.101.1.5

TruthValue

read-write

allows the redistribution of network 0.0.0.0 into BGP

ENA rcIpBgpGeneralGroupBestPathMissingAsWorst

1.3.6.1.4.1.2272.1.8.101.1.6

EnableValue

read-write

Enable to consider a missing MED attribute in a path as having a value of infinity, making the path without a MED value the least desirable path. To return the router to the default (assign a value of 0 to the missing MED), set the value to disable.

ENA rcIpBgpGeneralGroupBestPathMedConfed

1.3.6.1.4.1.2272.1.8.101.1.7

EnableValue

read-write

To enable MED comparison among paths learned from confederation peers. Disable to prevent considering the MED attribute in comparing paths

ENA rcIpBgpGeneralGroupIgnoreIllegalRouterId

1.3.6.1.4.1.2272.1.8.101.1.8

EnableValue

read-write

Configures BGP to overlook an illegal router ID. Enables or disable accepting a connection from a peer that sends its open message with a router ID of 0.

ENA rcIpBgpGeneralGroupAlwaysCompareMed

1.3.6.1.4.1.2272.1.8.101.1.9

EnableValue

read-write

Enable to allow the comparison of the Multi Exit Discriminator (MED) for paths from neighbors in different autonomous systems.

ENA rcIpBgpGeneralGroupAutoPeerRestart

1.3.6.1.4.1.2272.1.8.101.1.10

EnableValue

read-write

Enable the feature that automatically restarts the connection to a BGP peer when the connection goes down.

ENA rcIpBgpGeneralGroupAutoSummary

1.3.6.1.4.1.2272.1.8.101.1.11

EnableValue

read-write

Enable BGP to summarize networks based on class limlts (Class A,B,C networks).

ENA rcIpBgpGeneralGroupSynchronization

1.3.6.1.4.1.2272.1.8.101.1.12

EnableValue

read-write

Enables and disables the router from accepting routes from BGP peers without waiting for an update from the IBGP.

I32 rcIpBgpGeneralGroupMaxEqualcostRoutes

1.3.6.1.4.1.2272.1.8.101.1.13

Integer32

read-write

Sets the number of maximum number of equal-cost routes that can be stored in the routing table.

ENA rcIpBgpGeneralGroupIbgpReportImportRoute

1.3.6.1.4.1.2272.1.8.101.1.14

EnableValue

read-write

Configure BGP to report imported routes to an interior BGP peer.

ENA rcIpBgpGeneralGroupAggregate

1.3.6.1.4.1.2272.1.8.101.1.15

EnableValue

read-write

ENA rcIpBgpGeneralGroupFlapDampEnable

1.3.6.1.4.1.2272.1.8.101.1.16

EnableValue

read-write

Enabled or Disabled

I32 rcIpBgpGeneralGroupDebugMask

1.3.6.1.4.1.2272.1.8.101.1.17

Integer32

read-write

value is one of multiple (logically by 'OR' of following value: none (0), error(1), packet(2), event(4), trace(8), warning(16), state(32), init(64), filter(128), update(256), all(511) all(511): Enables all debugging messages. none(0): Disables all debugging messages. error(1): Enables disolay of debug error messages. packet(2): Enables display of debug packet messages. event(4): Enables display of debug event messages. trace(8): Enables display debug trace messages. warning(16): Enables display debug warning messages. state(32): Enables display of debug state transtion messages. init(64): Enables display of debug initialization messages. filter(128): Enables display of debug messages related to filtering. update(256): Enables display of debug messages related to sending and receiving updates.

ENA rcIpBgpGeneralGroupTrapEnable

1.3.6.1.4.1.2272.1.8.101.1.18

EnableValue

read-write

ENA rcIpBgpGeneralGroupQuickStart

1.3.6.1.4.1.2272.1.8.101.1.19

EnableValue

read-write

Enable the flag to avoid flap penalty and trigger the peer start event quickly

ENA rcIpBgpGeneralGroupDeterministicMed

1.3.6.1.4.1.2272.1.8.101.1.20

EnableValue

read-write

Enable to allow the comparison of the Multi Exit Discriminator (MED) for paths from neighbors in same autonomous system.

ENA rcIpBgpGeneralGroupRouteRefresh

1.3.6.1.4.1.2272.1.8.101.1.21

EnableValue

read-create

Route Refresh for Bgp.

STR rcIpBgpGeneralGroupRoutePolicyIn

1.3.6.1.4.1.2272.1.8.101.1.22

DisplayString

read-create

Route Policy Name that will be applied to all routes which enter the VRF table.

STR rcIpBgpGeneralGroupRoutePolicyOut

1.3.6.1.4.1.2272.1.8.101.1.23

DisplayString

read-create

Route policy name that will be applied to all routes which are sent out of this VRF instance.

T/F rcIpBgpGeneralGroupDefaultInformationOriginateIpv6

1.3.6.1.4.1.2272.1.8.101.1.24

TruthValue

read-write

allows the redistribution of default ipv6 network into BGP

OCT rcIpBgpGeneralGroupNewLocalAs

1.3.6.1.4.1.2272.1.8.101.1.25

OCTET STRING

read-write

Local Autonomous system number

ENA rcIpBgpGeneralGroup4ByteAs

1.3.6.1.4.1.2272.1.8.101.1.26

EnableValue

read-write

4 Byte As number enable

ENA rcIpBgpGeneralGroupAsDot

1.3.6.1.4.1.2272.1.8.101.1.27

EnableValue

read-write

As number in Dot format

I32 rcIpBgpAggregateTableSize

1.3.6.1.4.1.2272.1.8.101.2

Integer32

read-only

Size of Aggregate Table

rcIpBgpAggregateTable

1.3.6.1.4.1.2272.1.8.101.3

not-accessible

To specify the list of aggregate prefixes to be created by the BGP routing process and the options to be used while aggregating.

rcIpBgpAggregateEntry

1.3.6.1.4.1.2272.1.8.101.3.1

not-accessible

An entry of rcIpBgp Aggregate Address In Table.

IP rcIpBgpAggregateAddress

1.3.6.1.4.1.2272.1.8.101.3.1.1

IpAddress

read-only

Prefix to create an aggregate address in BGP routing table.

IP rcIpBgpAggregateMask

1.3.6.1.4.1.2272.1.8.101.3.1.2

IpAddress

read-only

Mask for the aggregrate

ENA rcIpBgpAggregateAsSetGenerate

1.3.6.1.4.1.2272.1.8.101.3.1.3

EnableValue

read-write

Enable Generates autonomous system set path information.

ENA rcIpBgpAggregateSummaryOnly

1.3.6.1.4.1.2272.1.8.101.3.1.4

EnableValue

read-write

Filters all more specific routes from updates.

STR rcIpBgpAggregateSuppressPolicy

1.3.6.1.4.1.2272.1.8.101.3.1.5

DisplayString

read-write

Name of route policy used to select the routes to be suppressed.

STR rcIpBgpAggregateAdvertisePolicy

1.3.6.1.4.1.2272.1.8.101.3.1.6

DisplayString

read-write

Name of route policy used to select the routes to create AS-SET origin communities.

STR rcIpBgpAggregateAttributePolicy

1.3.6.1.4.1.2272.1.8.101.3.1.7

DisplayString

read-write

Name of route policy used to set the attribute of the aggregate route.

ROW rcIpBgpAggregateRowStatus

1.3.6.1.4.1.2272.1.8.101.3.1.8

RowStatus

read-write

Row status for create/delete.

rcIpBgpConfederationGroup

1.3.6.1.4.1.2272.1.8.101.4

INT rcIpBgpConfederationIdentifier

1.3.6.1.4.1.2272.1.8.101.4.1

INTEGER

read-write

Confederation AS identifier

OCT rcIpBgpConfederationPeers

1.3.6.1.4.1.2272.1.8.101.4.2

OCTET STRING

read-write

The string represents ConfederatoinPeers as . Maximum size 255,if any, will not be recorded by this object. The length is a 1-octet field containing the numbner of peers in the value field. The value field contains one or more peers (AS numbers which are part of the confederation). Each AS is represented in the octet string as a pair of octets according to the following algorithm: first-byte-of-pair = ASNumber / 256; second-byte-of-pair = ASNumber & 255;

rcIpBgpRouteReflectorGroup

1.3.6.1.4.1.2272.1.8.101.5

ENA rcIpBgpRouteReflectionEnable

1.3.6.1.4.1.2272.1.8.101.5.1

EnableValue

read-write

Enable Route Reflection on this router

IP rcIpBgpRouteReflectorClusterId

1.3.6.1.4.1.2272.1.8.101.5.2

IpAddress

read-write

Cluster ID of this router acting as a route reflector

ENA rcIpBgpRouteReflectorClientToClientReflection

1.3.6.1.4.1.2272.1.8.101.5.3

EnableValue

read-write

When this router is configured as a route reflector, and the clients are fully meshed, a Disable value disables reflection of routes from one client to another.

ENA rcIpBgpRouteReflectionOperState

1.3.6.1.4.1.2272.1.8.101.5.4

EnableValue

read-only

Displays the current route reflection operational state

I32 rcIpBgpNetworkTableSize

1.3.6.1.4.1.2272.1.8.101.6

Integer32

read-only

Network Prefix table size

rcIpBgpNetworkTable

1.3.6.1.4.1.2272.1.8.101.7

not-accessible

The networks in this table are either static/directly connected or learned routes. Bgp advertises these network provided they are reachable and are in the IP routing table

rcIpBgpNetworkEntry

1.3.6.1.4.1.2272.1.8.101.7.1

not-accessible

An entry In NetworkTable.

IP rcIpBgpNetworkAddr

1.3.6.1.4.1.2272.1.8.101.7.1.1

IpAddress

read-write

Network prefix that BGP will advertise.

IP rcIpBgpNetworkMask

1.3.6.1.4.1.2272.1.8.101.7.1.2

IpAddress

read-only

Network mask

ROW rcIpBgpNetworkRowStatus

1.3.6.1.4.1.2272.1.8.101.7.1.3

RowStatus

read-write

Row status for create/delete.

INT rcIpBgpNetworkMetric

1.3.6.1.4.1.2272.1.8.101.7.1.4

INTEGER

read-write

Value of the metric to be used while sending an update for the routes from the network table. Indicates to set the MED value for the routes advertised to ebgp peers.

I32 rcIpBgpPeerTableSize

1.3.6.1.4.1.2272.1.8.101.8

Integer32

read-only

BGP peer table size

rcIpBgpPeerTable

1.3.6.1.4.1.2272.1.8.101.9

not-accessible

IP BGP Peer table

rcIpBgpPeerEntry

1.3.6.1.4.1.2272.1.8.101.9.1

not-accessible

An entry of Ip rcIpBgp Peer Table.

INT rcIpBgpPeerEnable

1.3.6.1.4.1.2272.1.8.101.9.1.1

INTEGER

read-write

Enable/Disable: controls whether the peer connection is enabled or disabled

IP rcIpBgpPeerIpAddress

1.3.6.1.4.1.2272.1.8.101.9.1.2

IpAddress

read-only

The Ip address of this peer

INT rcIpBgpPeerRemoteAs

1.3.6.1.4.1.2272.1.8.101.9.1.3

INTEGER

read-write

Remote Autonomous system number of this peer

STR rcIpBgpPeerGroupName

1.3.6.1.4.1.2272.1.8.101.9.1.4

DisplayString

read-write

Peer group name to which this peer belongs (optional)

ENA rcIpBgpPeerDefaultOriginate

1.3.6.1.4.1.2272.1.8.101.9.1.5

EnableValue

read-write

To allow a BGP speaker (the local router) to send the default route 0.0.0.0 to a neighbor for use as a default route

ENA rcIpBgpPeerEbgpMultiHop

1.3.6.1.4.1.2272.1.8.101.9.1.6

EnableValue

read-write

To accept and attempt BGP connections to external peers residing on networks that are not directly connected

INT rcIpBgpPeerAdvertisementInterval

1.3.6.1.4.1.2272.1.8.101.9.1.7

INTEGER

read-write

To set the minimum interval between the sending of BGP routing updates Time in seconds. Integer from 5 to 120.

STR rcIpBgpPeerPassword

1.3.6.1.4.1.2272.1.8.101.9.1.8

DisplayString

read-write

To enable MD5 authentication on a TCP connection between two BGP peers Case-sensitive password of up to 80 character

INT rcIpBgpPeerWeight

1.3.6.1.4.1.2272.1.8.101.9.1.9

INTEGER

read-write

To assign an absolute weight to a BGP network. It can be an integer from 0 to 65535.

INT rcIpBgpPeerMaxPrefix

1.3.6.1.4.1.2272.1.8.101.9.1.10

INTEGER

read-write

Sets a limit on the number of routes that will be accepted from a neighbor. A value of zero indicates no limit

T/F rcIpBgpPeerNextHopSelf

1.3.6.1.4.1.2272.1.8.101.9.1.11

TruthValue

read-write

Set NextHop Attribute to local router address before sending updates to remote peer

STR rcIpBgpPeerRoutePolicyIn

1.3.6.1.4.1.2272.1.8.101.9.1.12

DisplayString

read-write

Route Policy Name that will be applied to all networks learned from this peer

STR rcIpBgpPeerRoutePolicyOut

1.3.6.1.4.1.2272.1.8.101.9.1.13

DisplayString

read-write

Route policy name that will be applied to all outgoing updates

T/F rcIpBgpPeerRouteReflectorClient

1.3.6.1.4.1.2272.1.8.101.9.1.14

TruthValue

read-write

Indicates whether this peer is a route reflector client.

ENA rcIpBgpPeerSoftReconfigurationIn

1.3.6.1.4.1.2272.1.8.101.9.1.15

EnableValue

read-write

If Peer soft reconfiguration is enabled in the in-bound direction, policy can be changed and routes can re-learned without having to reset the bgp connection. Enabling soft reconfig-in causes all bgp routes to be stored in local memory (even non-best routes)

INT rcIpBgpPeerSoftReconfiguration

1.3.6.1.4.1.2272.1.8.101.9.1.16

INTEGER

read-write

If rcIpBgpPeerSoftReconfigurationIn is enabled in the in-bound direction, policy can be changed and routes can re-learned without having to reset the bgp connection by setting rcIpBgpPeerSoftReconfiguration to in(1). Setting the value to out (2) forces the neighbor to send out all the updates to the remote neighbor without resetting the connection.

ENA rcIpBgpPeerRemovePrivateAs

1.3.6.1.4.1.2272.1.8.101.9.1.17

EnableValue

read-write

Enable and disable private AS number from being stripped when sending an update

ROW rcIpBgpPeerRowStatus

1.3.6.1.4.1.2272.1.8.101.9.1.18

RowStatus

read-write

Used to create/delete entries in the Table.

ENA rcIpBgpPeerMD5Authentication

1.3.6.1.4.1.2272.1.8.101.9.1.19

EnableValue

read-write

Enable and Disable MD5 authentication

INT rcIpBgpPeerDebugMask

1.3.6.1.4.1.2272.1.8.101.9.1.20

INTEGER

read-write

value is one of multiple (logically by 'OR' of following value: none (0), error(1), packet(2), event(4), trace(8), warning(16), state(32), init(64), filter(128), update(256), all(511) all(511): Enables all debugging messages. none(0): Disables all debugging messages. error(1): Enables disolay of debug error messages. packet(2): Enables display of debug packet messages. event(4): Enables display of debug event messages. trace(8): Enables display debug trace messages. warning(16): Enables display debug warning messages. state(32): Enables display of debug state transtion messages. init(64): Enables display of debug initialization messages. filter(128): Enables display of debug messages related to filtering. update(256): Enables display of debug messages related to sending and receiving updates.

ENA rcIpBgpPeerSendCommunity

1.3.6.1.4.1.2272.1.8.101.9.1.21

EnableValue

read-write

IP rcIpBgpPeerUpdateSourceInterface

1.3.6.1.4.1.2272.1.8.101.9.1.22

IpAddress

read-write

The IP address to be used for Circuitless IP.

INT rcIpBgpPeerState

1.3.6.1.4.1.2272.1.8.101.9.1.25

INTEGER

read-only

The BGP peer connection state.

OCT rcIpBgpPeerLastError

1.3.6.1.4.1.2272.1.8.101.9.1.26

OCTET STRING

read-only

The last error code and subcode seen by this peer on this connection. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte OCTET STRING contains the error code, and the second byte contains the subcode.

ENA rcIpBgpPeerVpnv4Address

1.3.6.1.4.1.2272.1.8.101.9.1.27

EnableValue

read-create

The vpnv4 routes specified.

ENA rcIpBgpPeerIpvpnLiteCap

1.3.6.1.4.1.2272.1.8.101.9.1.28

EnableValue

read-create

The IPVPN-lite capability can be enabled or disabled on the bgp neighbor peer.

IP rcIpBgpPeerSooAddress

1.3.6.1.4.1.2272.1.8.101.9.1.29

IpAddress

read-create

The site-of-origin ip address.

INT rcIpBgpPeerSooAsNumber

1.3.6.1.4.1.2272.1.8.101.9.1.30

INTEGER

read-create

The asnum for the site-of-origin for bgp peer.

U32 rcIpBgpPeerSooAssignedNum

1.3.6.1.4.1.2272.1.8.101.9.1.31

Unsigned32

read-create

The Assigned number required along with asnum or address to configure the site-of-origin for bgp peer.

INT rcIpBgpPeerSooType

1.3.6.1.4.1.2272.1.8.101.9.1.32

INTEGER

read-only

The soo type can be asnum or ipaddress.

ENA rcIpBgpPeerRouteRefresh

1.3.6.1.4.1.2272.1.8.101.9.1.33

EnableValue

read-create

Route refresh for bgp peer.

ENA rcIpBgpPeerAsOverride

1.3.6.1.4.1.2272.1.8.101.9.1.34

EnableValue

read-create

The AS Override value can be enabled or disabled for bgp peer.

INT rcIpBgpPeerAllowAsIn

1.3.6.1.4.1.2272.1.8.101.9.1.35

INTEGER

read-create

The number of as-in allowed for bgp peer

I32 rcIpBgpPeerGroupTableSize

1.3.6.1.4.1.2272.1.8.101.10

Integer32

read-only

BGP Peer Group table size

rcIpBgpPeerGroupTable

1.3.6.1.4.1.2272.1.8.101.11

not-accessible

IP rcIpBgp Peer Group table. This table contains rows which are template configuration parameters which are shared by a group of peers. Peers belonging to the same group will refer to the same row in this table using a peer group name

rcIpBgpPeerGroupEntry

1.3.6.1.4.1.2272.1.8.101.11.1

not-accessible

An entry of Ip rcIpBgp Peer Group Table.

ENA rcIpBgpPeerGroupEnable

1.3.6.1.4.1.2272.1.8.101.11.1.1

EnableValue

read-create

Allows disabling a group of peers

I32 rcIpBgpPeerGroupIndex

1.3.6.1.4.1.2272.1.8.101.11.1.2

Integer32

read-only

Index in to the Peer Group Table

STR rcIpBgpPeerGroupGroupName

1.3.6.1.4.1.2272.1.8.101.11.1.3

DisplayString

read-create

Name of the BGP peer group to which this neighbor belong

I32 rcIpBgpPeerGroupRemoteAs

1.3.6.1.4.1.2272.1.8.101.11.1.4

Integer32

read-create

Remote Autonomous system number of this peer group (optional)

INT rcIpBgpPeerGroupDefaultOriginate

1.3.6.1.4.1.2272.1.8.101.11.1.5

INTEGER

read-create

Enabling this attribute allows a BGP speaker (the local router) to send the default route 0.0.0.0 to the group of neighbors for use as a default route.

INT rcIpBgpPeerGroupEbgpMultiHop

1.3.6.1.4.1.2272.1.8.101.11.1.6

INTEGER

read-create

To accept and attempt BGP connections to external peers residing on networks that are not directly connected

I32 rcIpBgpPeerGroupAdvertisementInterval

1.3.6.1.4.1.2272.1.8.101.11.1.7

Integer32

read-create

To set the minimum interval between the sending of BGP routing updates Time in seconds. Integer from 1 to 120.

I32 rcIpBgpPeerGroupKeepAlive

1.3.6.1.4.1.2272.1.8.101.11.1.8

Integer32

read-create

To set the time interval in seconds between the sending of BGP keep alive messages to remote peers.

I32 rcIpBgpPeerGroupHoldTime

1.3.6.1.4.1.2272.1.8.101.11.1.9

Integer32

read-create

To configure the hold time for the group of peers in seconds. Usually set to three times the value of the Keepalive time

I32 rcIpBgpPeerGroupWeight

1.3.6.1.4.1.2272.1.8.101.11.1.10

Integer32

read-create

To assign an absolute weight to a BGP network. Absolute weight, or importance. It can be an integer from 0 to 65535.

I32 rcIpBgpPeerGroupMaxPrefix

1.3.6.1.4.1.2272.1.8.101.11.1.11

Integer32

read-create

Sets a limit on the number of routes that will be accepted from this group of neighbors. A value of zero indicates no limit

T/F rcIpBgpPeerGroupNextHopSelf

1.3.6.1.4.1.2272.1.8.101.11.1.12

TruthValue

read-create

Set NextHop Attribute to local router address before sending updates to remote peers

STR rcIpBgpPeerGroupRoutePolicyIn

1.3.6.1.4.1.2272.1.8.101.11.1.13

DisplayString

read-create

Route Policy Name that will be applied to all networks learned from this group of peers

STR rcIpBgpPeerGroupRoutePolicyOut

1.3.6.1.4.1.2272.1.8.101.11.1.14

DisplayString

read-create

Route policy name that will be applied to all outgoing updates to this group of peers

T/F rcIpBgpPeerGroupRouteReflectorClient

1.3.6.1.4.1.2272.1.8.101.11.1.15

TruthValue

read-create

Indicates whether this group of peers is a route reflector client.

ENA rcIpBgpPeerGroupSoftReconfigurationIn

1.3.6.1.4.1.2272.1.8.101.11.1.16

EnableValue

read-create

If Peer soft reconfiguration is enabled in the in bound direction, policy can be changed and routes can re-learned without having to reset the bgp connection. Enabling soft reconfig-in causes all bgp routes to be stored in local memory (even non-best routes)

INT rcIpBgpPeerGroupSoftReconfiguration

1.3.6.1.4.1.2272.1.8.101.11.1.17

INTEGER

read-write

If Peer soft reconfiguration-in is enabled in the in bound direction, policy can be changed and routes can re-learned without having to reset the bgp connection by setting rcIpBgpPeerGroupSoftReconfiguration to in(1). Setting the value to out (2) forces the neighbor to send out all the updates to the remote neighbor without resetting the connection.

STR rcIpBgpPeerGroupPassword

1.3.6.1.4.1.2272.1.8.101.11.1.18

DisplayString

read-create

To enable MD5 authentication on TCP connections between this local speaker and this group of BGP peers. Case-sensitive password of up to 80 character

ENA rcIpBgpPeerGroupRemovePrivateAs

1.3.6.1.4.1.2272.1.8.101.11.1.19

EnableValue

read-create

Enable and disable private AS number from being stripped when sending an update

ROW rcIpBgpPeerGroupRowStatus

1.3.6.1.4.1.2272.1.8.101.11.1.20

RowStatus

read-create

row status

ENA rcIpBgpPeerGroupMD5Authentication

1.3.6.1.4.1.2272.1.8.101.11.1.21

EnableValue

read-create

Enable and Disable MD5 authentication

ENA rcIpBgpPeerGroupSendCommunity

1.3.6.1.4.1.2272.1.8.101.11.1.22

EnableValue

read-create

Enables or disables sending the update message community attribute to the specified peer.

IP rcIpBgpPeerGroupUpdateSourceInterface

1.3.6.1.4.1.2272.1.8.101.11.1.23

IpAddress

read-create

The IP address to used for circuitless IP for this peer group.

ENA rcIpBgpPeerGroupVpnv4Address

1.3.6.1.4.1.2272.1.8.101.11.1.24

EnableValue

read-create

The vpnv4 routes specified.

ENA rcIpBgpPeerGroupIpvpnLiteCap

1.3.6.1.4.1.2272.1.8.101.11.1.25

EnableValue

read-create

The IPVPN-lite capability can be enabled or disabled on the bgp neighbor peer group.

ENA rcIpBgpPeerGroupRouteRefresh

1.3.6.1.4.1.2272.1.8.101.11.1.30

EnableValue

read-create

Route refresh for bgp peer group.

ENA rcIpBgpPeerGroupAsOverride

1.3.6.1.4.1.2272.1.8.101.11.1.31

EnableValue

read-create

The AS Override value can be enabled or disabled for bgp peer group.

I32 rcIpBgpPeerGroupAllowAsIn

1.3.6.1.4.1.2272.1.8.101.11.1.32

Integer32

read-create

The number of as-in allowed for bgp peer group.

T/F rcIpBgpPeerGroupDefaultOriginateIpv6

1.3.6.1.4.1.2272.1.8.101.11.1.33

TruthValue

read-create

Enabling this attribute allows a BGP speaker (the local router) to send the default route to the group of neighbors for use as a default route.

IPt rcIpBgpPeerGroupAfUpdateSourceInterfaceType

1.3.6.1.4.1.2272.1.8.101.11.1.34

InetAddressType

read-create

The Inet address type used for circuitless IP for this peer group.

IP rcIpBgpPeerGroupAfUpdateSourceInterface

1.3.6.1.4.1.2272.1.8.101.11.1.35

InetAddress

read-create

The Inet address to used for circuitless IP for this peer group.

ENA rcIpBgpPeerGroupIpv6Cap

1.3.6.1.4.1.2272.1.8.101.11.1.36

EnableValue

read-create

The ipv6 capability can be enabled or disabled on the bgp neighbor peer group.

STR rcIpBgpPeerGroupIpv6RoutePolicyIn

1.3.6.1.4.1.2272.1.8.101.11.1.37

DisplayString

read-create

Ipv6 Route Policy Name that will be applied to all networks learned from this group of peers

STR rcIpBgpPeerGroupIpv6RoutePolicyOut

1.3.6.1.4.1.2272.1.8.101.11.1.38

DisplayString

read-create

Ipv6 Route policy name that will be applied to all outgoing updates to this group of peers

I32 rcIpBgpRcvdDampenedPathAttrTableSize

1.3.6.1.4.1.2272.1.8.101.12

Integer32

read-only

table size

rcIpBgpRcvdDampenedPathAttrTable

1.3.6.1.4.1.2272.1.8.101.13

not-accessible

This table contains info about paths to destination networks received from all BGP-4 peers

rcIpBgpDampenedPathAttrEntry

1.3.6.1.4.1.2272.1.8.101.13.1

not-accessible

Information about a path to a networks

IP rcIpBgpPathAttrPeer

1.3.6.1.4.1.2272.1.8.101.13.1.1

IpAddress

read-only

The IP address of the peer where the path info was learned

INT rcIpBgpPathAttrIpAddrPrefixLen

1.3.6.1.4.1.2272.1.8.101.13.1.2

INTEGER

read-only

Length in bits of the IP address prefix in the network Layer Reachablity Information field.

IP rcIpBgpPathAttrIpAddrPrefix

1.3.6.1.4.1.2272.1.8.101.13.1.3

IpAddress

read-only

An Ip address prefix in the NLRI Information field. This object is an IP address containing the prefix with length specified by rcIpBgpPathAttrIpAddrPrefixLen are zeroed.

I32 rcIpBgpPathAttrFlapPenalty

1.3.6.1.4.1.2272.1.8.101.13.1.4

Integer32

read-only

Penalty value based on number of route flaps

I32 rcIpBgpPathAttrFlapCount

1.3.6.1.4.1.2272.1.8.101.13.1.5

Integer32

read-only

Number of times a route flapped since the last time the penalty was reset to zero

INT rcIpBgpPathAttrRouteDampened

1.3.6.1.4.1.2272.1.8.101.13.1.6

INTEGER

read-only

Shows whether this route is currently suppressed from being announced

I32 rcIpBgpPathAttrReuseTime

1.3.6.1.4.1.2272.1.8.101.13.1.7

Integer32

read-only

Re use time is the system configured time for route reuse

I32 rcIpBgpPathAttrReuseTimeRemain

1.3.6.1.4.1.2272.1.8.101.13.1.8

Integer32

read-only

Re use time Remain is the number of seconds before the route will be reused

I32 rcIpBgp4PathAttrTableSize

1.3.6.1.4.1.2272.1.8.101.14

Integer32

read-only

table size

rcIpBgp4PathAttrTable

1.3.6.1.4.1.2272.1.8.101.15

not-accessible

This table contains info about paths to destination networks received from all BGP-4 peers

rcIpBgp4PathAttrEntry

1.3.6.1.4.1.2272.1.8.101.15.1

not-accessible

IP rcIpBgp4PathAttrPeer

1.3.6.1.4.1.2272.1.8.101.15.1.1

IpAddress

read-only

The IP address of the peer where the path info was learned

INT rcIpBgp4PathAttrIpAddrPrefixLen

1.3.6.1.4.1.2272.1.8.101.15.1.2

INTEGER

read-only

Length in bits of the IP address prefix in the network Layer Reachablity Information field.

IP rcIpBgp4PathAttrIpAddrPrefix

1.3.6.1.4.1.2272.1.8.101.15.1.3

IpAddress

read-only

An Ip address prefix in the NLRI Information field. This object is an IP address containing the prefix with length specified by rcIpBgpPathAttrIpAddrPrefixLen are zeroed.

OCT rcIpBgp4PathAttrCommunities

1.3.6.1.4.1.2272.1.8.101.15.1.4

OCTET STRING

read-only

The string represents community path attributes as The length is a 1-octet field containing the numbner of community numbers in the value field.The value field contains one or more Community numbers,each community is represented in the octet string as 4 octets.The community numbers in the string beyond maximum size 255,if any, will not be recorded by this object.

IP rcIpBgp4PathAttrOriginateId

1.3.6.1.4.1.2272.1.8.101.15.1.5

IpAddress

read-only

The IP address of the route who originates the routes

OCT rcIpBgp4PathAttrClusterId

1.3.6.1.4.1.2272.1.8.101.15.1.6

OCTET STRING

read-only

The string represents Cluster Id path attributes as The length is a 1-octet field containing the number of Cluster Id numbers in the value field.The value field contains one or more Cluster Id numbers,each Cluster Id is represented in the octet string as 4 octets,each four octets is the IpAddress of the router acting as a route reflector.The Cluster Id numbers in the string beyond maximum size 255,if any, will not be recorded by this object.

rcIpBgpExt

1.3.6.1.4.1.2272.1.8.101.16

U32 rcIpBgpExtAggregateAfTableSize

1.3.6.1.4.1.2272.1.8.101.16.1

Unsigned32

read-only

Size of address family independent bgp aggregate table

rcIpBgpExtAggregateAfTable

1.3.6.1.4.1.2272.1.8.101.16.2

not-accessible

Replaces rcIpBgpAggregateTable. To specify the list of ipv4 and ipv6 aggregate prefixes to be created by the BGP routing process and the options to be used while aggregating.

rcIpBgpExtAggregateAfEntry

1.3.6.1.4.1.2272.1.8.101.16.2.1

not-accessible

An entry of v4/v6 aggregate prefix to be created by BGP routing process and the options to be used while aggregating.

IPt rcIpBgpExtAggregateAfAddressType

1.3.6.1.4.1.2272.1.8.101.16.2.1.1

InetAddressType

not-accessible

Inet Address Type of aggregate address.

IP rcIpBgpExtAggregateAfAddress

1.3.6.1.4.1.2272.1.8.101.16.2.1.2

InetAddress

not-accessible

V4 or V6 Prefix to create an aggregate address in BGP routing table.

ADR rcIpBgpExtAggregateAfPrefixLen

1.3.6.1.4.1.2272.1.8.101.16.2.1.3

InetAddressPrefixLength

not-accessible

Prefix length of the aggregate inet address

T/F rcIpBgpExtAggregateAfAsSetGenerate

1.3.6.1.4.1.2272.1.8.101.16.2.1.4

TruthValue

read-create

Enable Generates autonomous system set path information.

T/F rcIpBgpExtAggregateAfSummaryOnly

1.3.6.1.4.1.2272.1.8.101.16.2.1.5

TruthValue

read-create

Filters all more specific routes from updates.

STR rcIpBgpExtAggregateAfSuppressPolicy

1.3.6.1.4.1.2272.1.8.101.16.2.1.6

SnmpAdminString

read-create

Name of route policy used to select the routes to be suppressed.

STR rcIpBgpExtAggregateAfAdvertisePolicy

1.3.6.1.4.1.2272.1.8.101.16.2.1.7

SnmpAdminString

read-create

Name of route policy used to select the routes to create AS-SET origin communities.

STR rcIpBgpExtAggregateAfAttributePolicy

1.3.6.1.4.1.2272.1.8.101.16.2.1.8

SnmpAdminString

read-create

Name of route policy used to set the attribute of the aggregate route.

ROW rcIpBgpExtAggregateAfRowStatus

1.3.6.1.4.1.2272.1.8.101.16.2.1.9

RowStatus

read-create

Row status for create/delete.

U32 rcIpBgpExtNetworkAfTableSize

1.3.6.1.4.1.2272.1.8.101.16.3

Unsigned32

read-only

Address family independent bgp Network Prefix table size

rcIpBgpExtNetworkAfTable

1.3.6.1.4.1.2272.1.8.101.16.4

not-accessible

This table replaces rcIpBgpNetworkTable. This table supports V4 and V6 BGP networks. The networks in this table are either static/directly connected or learned routes. Bgp advertises these network provided they are reachable and are in the IP routing table

rcIpBgpExtNetworkAfEntry

1.3.6.1.4.1.2272.1.8.101.16.4.1

not-accessible

An entry in bgp NetworkTable.

IPt rcIpBgpExtNetworkAfAddrType

1.3.6.1.4.1.2272.1.8.101.16.4.1.1

InetAddressType

not-accessible

Inet address type of the Network prefix that BGP will advertise.

IP rcIpBgpExtNetworkAfAddr

1.3.6.1.4.1.2272.1.8.101.16.4.1.2

InetAddress

not-accessible

v4/v6 Network prefix that BGP will advertise.

ADR rcIpBgpExtNetworkAfPrefixLen

1.3.6.1.4.1.2272.1.8.101.16.4.1.3

InetAddressPrefixLength

not-accessible

Prefix length of the v4/v6 bgp network address

I32 rcIpBgpExtNetworkAfMetric

1.3.6.1.4.1.2272.1.8.101.16.4.1.4

Integer32

read-create

Value of the metric to be used while sending an update for the routes from the network table. Indicates to set the MED value for the routes advertised to ebgp Peers.

ROW rcIpBgpExtNetworkAfRowStatus

1.3.6.1.4.1.2272.1.8.101.16.4.1.5

RowStatus

read-create

Row status for create/delete.

U32 rcIpBgpExtPeerAfTableSize

1.3.6.1.4.1.2272.1.8.101.16.5

Unsigned32

read-only

Size of Address family independent BGP Peer Table

rcIpBgpExtPeerAfTable

1.3.6.1.4.1.2272.1.8.101.16.6

not-accessible

Extension to the BGP peer table. This table contains, one entry per BGP peer, information about the connections with BGP Peers, which is not supported by the standard MIB draft. This table replaces rcIpBgpPeerTable.

rcIpBgpExtPeerAfEntry

1.3.6.1.4.1.2272.1.8.101.16.6.1

not-accessible

Entry containing miscelleneous information (info not present in the standard BGP peer table) about the connection with a remote BGP peer .

STR rcIpBgpExtPeerAfGroupName

1.3.6.1.4.1.2272.1.8.101.16.6.1.1

SnmpAdminString

read-create

Peer group name to which this peer belongs (optional)

T/F rcIpBgpExtPeerAfDefaultOriginate

1.3.6.1.4.1.2272.1.8.101.16.6.1.2

TruthValue

read-create

To allow a BGP speaker (the local router) to send the default route 0.0.0.0 to a neighbor for use as a default route

T/F rcIpBgpExtPeerAfDefaultOriginateIpv6

1.3.6.1.4.1.2272.1.8.101.16.6.1.3

TruthValue

read-create

To allow a BGP speaker (the local router) to Send the default ipv6 route to a neighbor for use as a default route

T/F rcIpBgpExtPeerAfEbgpMultiHop

1.3.6.1.4.1.2272.1.8.101.16.6.1.4

TruthValue

read-create

To accept and attempt BGP connections to external peers residing on networks that are not directly connected

I32 rcIpBgpExtPeerAfAdvertisementInterval

1.3.6.1.4.1.2272.1.8.101.16.6.1.5

Integer32

read-create

To set the minimum interval between the sending Of BGP routing updates Time in seconds. Integer from 5 to 120.

STR rcIpBgpExtPeerAfPassword

1.3.6.1.4.1.2272.1.8.101.16.6.1.6

SnmpAdminString

read-create

To enable MD5 authentication on a TCP connection between two BGP Peers Case-sensitive password of up to 80 character

I32 rcIpBgpExtPeerAfWeight

1.3.6.1.4.1.2272.1.8.101.16.6.1.7

Integer32

read-create

To assign an absolute weight to a BGP network. It can be an integer from 0 to 65535.

I32 rcIpBgpExtPeerAfMaxPrefix

1.3.6.1.4.1.2272.1.8.101.16.6.1.8

Integer32

read-create

Sets a limit on the number of routes that will be accepted from a neighbor. A value of zero indicates no limit

T/F rcIpBgpExtPeerAfNextHopSelf

1.3.6.1.4.1.2272.1.8.101.16.6.1.9

TruthValue

read-create

Set NextHop Attribute to local router address Before sending updates to remote peer

STR rcIpBgpExtPeerAfRoutePolicyIn

1.3.6.1.4.1.2272.1.8.101.16.6.1.10

SnmpAdminString

read-create

Route Policy Name that will be applied to all Networks learned from this peer

STR rcIpBgpExtPeerAfRoutePolicyOut

1.3.6.1.4.1.2272.1.8.101.16.6.1.11

SnmpAdminString

read-create

Route policy name that will be applied to all outgoing updates

T/F rcIpBgpExtPeerAfRouteReflectorClient

1.3.6.1.4.1.2272.1.8.101.16.6.1.12

TruthValue

read-create

Indicates whether this peer is a route reflector client.

T/F rcIpBgpExtPeerAfSoftReconfigurationIn

1.3.6.1.4.1.2272.1.8.101.16.6.1.13

TruthValue

read-create

If Peer soft reconfiguration is enabled in the in-bound direction, policy can be changed and routes can re-learned without having to reset the bgp connection. Enabling soft reconfig-in causes all bgp routes to be stored in local memory (even non-best routes)

INT rcIpBgpExtPeerAfSoftReconfiguration

1.3.6.1.4.1.2272.1.8.101.16.6.1.14

INTEGER

read-create

If rcIpBgpExtPeerAfSoftReconfigurationIn is enabled in the in-bound direction, policy can be changed and routes can re-learned without having to reset the bgp connection by setting rcIpBgpExtPeerAfSoftReconfiguration to in(1). Setting the value to out (2) forces the neighbor to send out all the updates to the remote neighbor without resetting the connection.

T/F rcIpBgpExtPeerAfRemovePrivateAs

1.3.6.1.4.1.2272.1.8.101.16.6.1.15

TruthValue

read-create

Enable and disable private AS number from being stripped when sending an update

T/F rcIpBgpExtPeerAfMD5Authentication

1.3.6.1.4.1.2272.1.8.101.16.6.1.16

TruthValue

read-create

Enable and Disable MD5 authentication

I32 rcIpBgpExtPeerAfDebugMask

1.3.6.1.4.1.2272.1.8.101.16.6.1.17

Integer32

read-create

value is one of multiple (logically by 'OR' of following value: none (0), error(1), packet(2), event(4), trace(8), warning(16), state(32), init(64), filter(128), update(256), all(511) all(511): Enables all debugging messages. none(0): Disables all debugging messages. error(1): Enables display of debug error messages. packet(2): Enables display of debug packet messages. event(4): Enables display of debug event messages. trace(8): Enables display debug trace messages. warning(16): Enables display debug warning messages. state(32): Enables display of debug state transition messages. init(64): Enables display of debug initialization messages. filter(128): Enables display of debug messages related to filtering. update(256): Enables display of debug messages related to sending and receiving updates.

T/F rcIpBgpExtPeerAfSendCommunity

1.3.6.1.4.1.2272.1.8.101.16.6.1.18

TruthValue

read-create

Enables or disables sending the update message community attribute to the specified peer.

IP rcIpBgpExtPeerAfUpdateSourceInterface

1.3.6.1.4.1.2272.1.8.101.16.6.1.19

InetAddress

read-create

The Inet address to be used for Circuitless IP.

T/F rcIpBgpExtPeerAfVpnv4Address

1.3.6.1.4.1.2272.1.8.101.16.6.1.20

TruthValue

read-create

The vpnv4 routes specified.

T/F rcIpBgpExtPeerAfIpv6Cap

1.3.6.1.4.1.2272.1.8.101.16.6.1.21

TruthValue

read-create

The ipv6 capability can be enabled or disabled on the bgp neighbor peer.

T/F rcIpBgpExtPeerAfIpvpnLiteCap

1.3.6.1.4.1.2272.1.8.101.16.6.1.22

TruthValue

read-create

The IPVPN-lite capability can be enabled or disabled on the bgp neighbor peer.

IP rcIpBgpExtPeerAfSooAddress

1.3.6.1.4.1.2272.1.8.101.16.6.1.23

IpAddress

read-create

The site-of-origin ip address.

I32 rcIpBgpExtPeerAfSooAsNumber

1.3.6.1.4.1.2272.1.8.101.16.6.1.24

Integer32

read-create

The asnum for the site-of-origin for bgp peer.

U32 rcIpBgpExtPeerAfSooAssignedNum

1.3.6.1.4.1.2272.1.8.101.16.6.1.25

Unsigned32

read-create

The Assigned number required along with asnum or address to configure the site-of-origin for bgp peer.

INT rcIpBgpExtPeerAfSooType

1.3.6.1.4.1.2272.1.8.101.16.6.1.26

INTEGER

read-only

The soo type can be asnum or ipaddress.

T/F rcIpBgpExtPeerAfRouteRefresh

1.3.6.1.4.1.2272.1.8.101.16.6.1.27

TruthValue

read-create

Route refresh for bgp peer.

T/F rcIpBgpExtPeerAfAsOverride

1.3.6.1.4.1.2272.1.8.101.16.6.1.28

TruthValue

read-create

The AS Override value can be enabled or disabled for bgp peer.

I32 rcIpBgpExtPeerAfAllowAsIn

1.3.6.1.4.1.2272.1.8.101.16.6.1.29

Integer32

read-create

The number of as-in allowed for bgp peer.

STR rcIpBgpExtPeerAfIpv6RoutePolicyIn

1.3.6.1.4.1.2272.1.8.101.16.6.1.30

SnmpAdminString

read-create

Ipv6 Route Policy Name that will be applied to all Networks learned from this peer

STR rcIpBgpExtPeerAfIpv6RoutePolicyOut

1.3.6.1.4.1.2272.1.8.101.16.6.1.31

SnmpAdminString

read-create

Ipv6 Route policy name that will be applied to all outgoing updates

T/F rcIpBgpExtPeerAfEnable

1.3.6.1.4.1.2272.1.8.101.16.6.1.32

TruthValue

read-create

Used to enable/disable bgp+ peer

INE rcIpBgpExtPeerAfRemoteAs

1.3.6.1.4.1.2272.1.8.101.16.6.1.33

InetAutonomousSystemNumber

read-create

Used to manually configure the remote as of the bgp+ peer.

U32 rcIpBgpExtPeerAfConnectRetryInterval

1.3.6.1.4.1.2272.1.8.101.16.6.1.34

Unsigned32

read-create

Used to configure the ConnectRetry timer for the BGP+ peer.

U32 rcIpBgpExtPeerAfHoldTimeConfigured

1.3.6.1.4.1.2272.1.8.101.16.6.1.35

Unsigned32

read-create

Used to configure the Hold Timer for the BGP+ peer.

U32 rcIpBgpExtPeerAfKeepAliveConfigured

1.3.6.1.4.1.2272.1.8.101.16.6.1.36

Unsigned32

read-create

Used to configure the KeepAlive Timer for the BGP+ peer.

ROW rcIpBgpExtPeerAfRowStatus

1.3.6.1.4.1.2272.1.8.101.16.6.1.37

RowStatus

read-create

Used to create/delete entries in the Table.

OCT rcIpBgpExtPeerAfNewRemoteAs

1.3.6.1.4.1.2272.1.8.101.16.6.1.38

OCTET STRING

read-create

Remote Autonomous system number of this peer

rcIpBgpExtAfPathAttrTable

1.3.6.1.4.1.2272.1.8.101.16.7

not-accessible

Extension to rcIpBgpTmpAfPathAttrTable. This table contains info about additional BGP path attributes not covered in rcIpBgpTmpAfPathAttrTable.

rcIpBgpExtAfPathAttrEntry

1.3.6.1.4.1.2272.1.8.101.16.7.1

not-accessible

Each entry contains data about additional path attributes associated with a given prefix in the rcIpBgpTmpNlriTable.

OCT rcIpBgpExtAfPathAttrUnknown

1.3.6.1.4.1.2272.1.8.101.16.7.1.1

OCTET STRING

read-only

Replaces bgp4PathAttrUnknown. One or more path attributes not understood by this BGP4 speaker. Size zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size, if any, are not recorded by this object.

OCT rcIpBgpExtAfPathAttrCommunities

1.3.6.1.4.1.2272.1.8.101.16.7.1.2

OCTET STRING

read-only

The string represents BGP+ community path attributes as . The length is a 1-octet field containing the numbner of community numbers in the value field.The value field contains one or more Community numbers,each community is represented in the octet string as 4 octets.The community numbers in the string beyond maximum size 255,if any, will not be recorded by this object.

IP rcIpBgpExtAfPathAttrOriginateId

1.3.6.1.4.1.2272.1.8.101.16.7.1.3

IpAddress

read-only

In a BGP+ context, the IP address of the router which originates the routes.

OCT rcIpBgpExtAfPathAttrClusterId

1.3.6.1.4.1.2272.1.8.101.16.7.1.4

OCTET STRING

read-only

The string represents BGP+ Cluster Id path attributes as . The length is a 1-octet field containing the number of Cluster Id numbers in the value field. The value field contains one or more Cluster Id numbers, each Cluster Id is represented in the octet string as 4 octets, each four octets is the IpAddress of the router acting as a route reflector.The Cluster Id numbers in the string beyond maximum size 255,if any, will not be recorded by this object.

rcIpBgpTmp

1.3.6.1.4.1.2272.1.8.101.17

rcIpBgpTmpNotification

1.3.6.1.4.1.2272.1.8.101.17.0

NTF rcIpBgpTmpEstablishedNotification

1.3.6.1.4.1.2272.1.8.101.17.0.1

The rcIpBgpTmpEstablishedNotification event is generated when the BGP FSM enters the established state. This Notification replaces the bgpEstablished Notification and has been replaced by rcIpBgpTmpAfEstablishedNotification.

NTF rcIpBgpTmpBackwardTransNotification

1.3.6.1.4.1.2272.1.8.101.17.0.2

The rcIpBgpBackwardTransNotification event is generated when the BGP FSM moves from a higher numbered state to a lower numbered state. This Notification replaces the bgpBackwardsTransition Notification and has been replaced by rcIpBgpTmpAfBackwardsNotification.

NTF rcIpBgpTmpAfEstablishedNotification

1.3.6.1.4.1.2272.1.8.101.17.0.3

The BGP Established event is generated when the BGP FSM enters the established state.

NTF rcIpBgpTmpAfBackwardTransitionNotification

1.3.6.1.4.1.2272.1.8.101.17.0.4

The BGPBackwardTransition Event is generated when the BGP FSM moves from a higher numbered state to a lower numbered state. Due to the nature of the BGP state machine, an implementation MAY rate limit the generation of this event. An implementation MAY also generate this notification ONLY when the state machine moves out of the established state. An implementation should document its specific behavior.

INE rcIpBgpTmpLocalAsNew

1.3.6.1.4.1.2272.1.8.101.17.9

InetAutonomousSystemNumber

read-only

The local autonomous system number. This object supports 4 byte ASes and replaces bgpLocalAs.

rcIpBgpTmpPeerAf

1.3.6.1.4.1.2272.1.8.101.17.10

rcIpBgpTmpPeerAfTable

1.3.6.1.4.1.2272.1.8.101.17.10.1

not-accessible

BGP peer table. This table contains, one entry per BGP peer, information about the connections with BGP peers. This table replaces bgpPeerTable.

rcIpBgpTmpPeerAfEntry

1.3.6.1.4.1.2272.1.8.101.17.10.1.1

not-accessible

Entry containing information about the connection with a remote BGP peer.

U32 rcIpBgpTmpPeerAfInstance

1.3.6.1.4.1.2272.1.8.101.17.10.1.1.1

Unsigned32

not-accessible

The routing instance index. Some BGP implementations permit the creation of multiple instances of a BGP routing process. An example includes routers running BGP/MPLS IP Virtual Private Networks. Implementations that do not support multiple routing instances should return 1 for this object.

IPt rcIpBgpTmpPeerAfLocalAddrType

1.3.6.1.4.1.2272.1.8.101.17.10.1.1.2

InetAddressType

not-accessible

The address family of the local end of the peering session.

IP rcIpBgpTmpPeerAfLocalAddr

1.3.6.1.4.1.2272.1.8.101.17.10.1.1.3

InetAddress

not-accessible

The local IP address of this entry's BGP connection.

IPt rcIpBgpTmpPeerAfRemoteAddrType

1.3.6.1.4.1.2272.1.8.101.17.10.1.1.4

InetAddressType

not-accessible

The address family of the remote end of the peering session.

IP rcIpBgpTmpPeerAfRemoteAddr

1.3.6.1.4.1.2272.1.8.101.17.10.1.1.5

InetAddress

not-accessible

The remote IP address of this entry's BGP peer.

INE rcIpBgpTmpPeerAfLocalPort

1.3.6.1.4.1.2272.1.8.101.17.10.1.1.6

InetPortNumber

read-only

The local port for the TCP connection between the BGP peers.

INE rcIpBgpTmpPeerAfLocalAs

1.3.6.1.4.1.2272.1.8.101.17.10.1.1.7

InetAutonomousSystemNumber

read-only

Some implementations of BGP can represent themselves as multiple ASes. This is the AS that this peering session is representing itself as to the remote peer.

INE rcIpBgpTmpPeerAfRemotePort

1.3.6.1.4.1.2272.1.8.101.17.10.1.1.8

InetPortNumber

read-only

The remote port for the TCP connection between the BGP peers. Note that the objects rcIpBgpTmpPeerAfLocalAddr, rcIpBgpTmpPeerAfLocalPort, rcIpBgpTmpPeerAfRemoteAddr and rcIpBgpTmpPeerAfRemotePort provide the appropriate reference to the standard MIB TCP connection table, or even the ipv6 TCP MIB as in RFC 4022.

INE rcIpBgpTmpPeerAfRemoteAs

1.3.6.1.4.1.2272.1.8.101.17.10.1.1.9

InetAutonomousSystemNumber

read-only

The remote autonomous system number received in the BGP OPEN message.

OID rcIpBgpTmpPeerAfIdentifier

1.3.6.1.4.1.2272.1.8.101.17.10.1.1.10

RcIpBgpTmpIdentifierTC

read-only

The BGP Identifier of this entry's remote BGP peer. This entry should be 0.0.0.0 unless the rcIpBgpTmpPeerAfPeerState is in the openconfirm or the established state.

INT rcIpBgpTmpPeerAfAdminStatus

1.3.6.1.4.1.2272.1.8.101.17.10.1.1.11

INTEGER

read-only

Whether or not the BGP FSM for this remote peer is halted or running. The BGP FSM for a remote peer is halted after processing a Stop event. Likewise, it is in the running state after a Start event. The rcIpBgpTmpPeerAfState will generally be in the idle state when the FSM is halted, although some extensions such as Graceful Restart will leave the peer in the Idle state but with the FSM running.

INT rcIpBgpTmpPeerAfPeerState

1.3.6.1.4.1.2272.1.8.101.17.10.1.1.12

INTEGER

read-only

The BGP peer connection state.

U32 rcIpBgpTmpPeerAfConfiguredVersion

1.3.6.1.4.1.2272.1.8.101.17.10.1.1.13

Unsigned32

read-only

The configured version to originally start with this remote peer. The BGP speaker may permit negotiation to a lower version number of the protocol.

U32 rcIpBgpTmpPeerAfNegotiatedVersion

1.3.6.1.4.1.2272.1.8.101.17.10.1.1.14

Unsigned32

read-only

The negotiated version of BGP running between the two peers. This entry MUST be zero (0) unless the rcIpBgpTmpPeerAfState is in the openconfirm or the established state. Note that legal values for this object are between 0 and 255.

rcIpBgpTmpPeerAfErrors

1.3.6.1.4.1.2272.1.8.101.17.10.2

rcIpBgpTmpPeerAfErrorsTable

1.3.6.1.4.1.2272.1.8.101.17.10.2.1

not-accessible

On a per-peer basis, this table reflects the last protocol-defined error encountered and reported on the peer session. If no entry for a given peer exists in this table, then no such errors have been observed, reported, and recorded on the session.

rcIpBgpTmpPeerAfErrorsEntry

1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1

not-accessible

Each entry contains information about errors sent and received for a particular BGP peer.

OCT rcIpBgpTmpPeerAfLastErrorCodeReceived

1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.1

OCTET STRING

read-only

The last error code received from this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero.

OCT rcIpBgpTmpPeerAfLastErrorSubCodeReceived

1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.2

OCTET STRING

read-only

The last subcode received from this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero.

TIM rcIpBgpTmpPeerAfLastErrorReceivedTime

1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.3

TimeStamp

read-only

The timestamp that the last NOTIFICATION was received from this peer.

STR rcIpBgpTmpPeerAfLastErrorReceivedText

1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.4

SnmpAdminString

read-only

This object contains an implementation specific explanation of the error that was reported.

OCT rcIpBgpTmpPeerAfLastErrorReceivedData

1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.5

OCTET STRING

read-only

The last error code's data seen by this peer. Per RFC 2578, some implementations may have limitations dealing with OCTET STRINGS larger than 255. Thus, this data may be truncated.

OCT rcIpBgpTmpPeerAfLastErrorCodeSent

1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.6

OCTET STRING

read-only

The last error code sent to this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero.

OCT rcIpBgpTmpPeerAfLastErrorSubCodeSent

1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.7

OCTET STRING

read-only

The last subcode sent to this peer via NOTIFICATION message on this connection. If no error has occurred, this field is zero.

TIM rcIpBgpTmpPeerAfLastErrorSentTime

1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.8

TimeStamp

read-only

The timestamp that the last NOTIFICATION was sent to this peer.

STR rcIpBgpTmpPeerAfLastErrorSentText

1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.9

SnmpAdminString

read-only

This object contains an implementation specific explanation of the error that is being reported.

OCT rcIpBgpTmpPeerAfLastErrorSentData

1.3.6.1.4.1.2272.1.8.101.17.10.2.1.1.10

OCTET STRING

read-only

The last error code's data sent to this peer. Per RFC 2578, some implementations may have limitations dealing with OCTET STRINGS larger than 255. Thus, this data may be truncated.

rcIpBgpTmpPeerAfTimers

1.3.6.1.4.1.2272.1.8.101.17.10.3

rcIpBgpTmpPeerAfEventTimesTable

1.3.6.1.4.1.2272.1.8.101.17.10.3.1

not-accessible

A table reporting the per-peering session amount of time elapsed and update events since the peering session advanced into the established state.

rcIpBgpTmpPeerAfEventTimesEntry

1.3.6.1.4.1.2272.1.8.101.17.10.3.1.1

not-accessible

Each row contains a set of statistics about time spent and events encountered in the peer session established state.

G32 rcIpBgpTmpPeerAfFsmEstablishedTime

1.3.6.1.4.1.2272.1.8.101.17.10.3.1.1.1

Gauge32

read-only

This timer indicates how long (in seconds) this peer has been in the established state or how long since this peer was last in the established state. It is set to zero when a new peer is configured or when the router is booted. If the peer has never reached the established state, the value remains zero.

G32 rcIpBgpTmpPeerAfInUpdatesElapsedTime

1.3.6.1.4.1.2272.1.8.101.17.10.3.1.1.2

Gauge32

read-only

Elapsed time (in seconds) since the last BGP UPDATE message was received from the peer. Each time bgpPeerInUpdates is incremented, the value of this object is set to zero (0).

rcIpBgpTmpPeerAfConfiguredTimersTable

1.3.6.1.4.1.2272.1.8.101.17.10.3.2

not-accessible

Per peer management data on BGP session timers.

rcIpBgpTmpPeerAfConfiguredTimersEntry

1.3.6.1.4.1.2272.1.8.101.17.10.3.2.1

not-accessible

Each entry corresponds to the current state of BGP timers on a given peering session.

U32 rcIpBgpTmpPeerAfConnectRetryInterval

1.3.6.1.4.1.2272.1.8.101.17.10.3.2.1.1

Unsigned32

read-only

Time interval (in seconds) for the ConnectRetry timer. The suggested value for this timer is 120 seconds.

U32 rcIpBgpTmpPeerAfHoldTimeConfigured

1.3.6.1.4.1.2272.1.8.101.17.10.3.2.1.2

Unsigned32

read-only

Time interval (in seconds) for the Hold Timer established with the peer. The value of this object is calculated by this BGP speaker, using the smaller of the values in bgpPeerHoldTimeConfigured and the Hold Time received in the OPEN message. This value must be at least three seconds if it is not zero (0). If the Hold Timer has not been established with the peer this object MUST have a value of zero (0). If the bgpPeerHoldTimeConfigured object has a value of (0), then this object MUST have a value of (0).

U32 rcIpBgpTmpPeerAfKeepAliveConfigured

1.3.6.1.4.1.2272.1.8.101.17.10.3.2.1.3

Unsigned32

read-only

Time interval (in seconds) for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages' frequency relative to the value specified in bgpPeerHoldTimeConfigured; the actual time interval for the KEEPALIVE messages is indicated by bgpPeerKeepAlive. A reasonable maximum value for this timer would be one third of that of bgpPeerHoldTimeConfigured. If the value of this object is zero (0), no periodic KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds.

U32 rcIpBgpTmpPeerAfMinASOrigInterval

1.3.6.1.4.1.2272.1.8.101.17.10.3.2.1.4

Unsigned32

read-only

Time interval (in seconds) for the MinASOriginationInterval timer. The suggested value for this timer is 15 seconds.

U32 rcIpBgpTmpPeerAfMinRouteAdverInterval

1.3.6.1.4.1.2272.1.8.101.17.10.3.2.1.5

Unsigned32

read-only

Time interval (in seconds) for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds for EBGP connections and 5 seconds for IBGP connections.

rcIpBgpTmpPeerAfNegotiatedTimersTable

1.3.6.1.4.1.2272.1.8.101.17.10.3.3

not-accessible

Configured values of per-peer timers are seen in the rcIpBgpTmpPeerAfConfiguredTimersTable. Values in this table reflect the current operational values, after negotiation from values derived from initial configuration.

rcIpBgpTmpPeerAfNegotiatedTimersEntry

1.3.6.1.4.1.2272.1.8.101.17.10.3.3.1

not-accessible

Each entry reflects a value of the currently operational, negotiated timer as reflected in the rcIpBgpTmpPeerAfNegotiatedTimersEntry.

U32 rcIpBgpTmpPeerAfHoldTime

1.3.6.1.4.1.2272.1.8.101.17.10.3.3.1.1

Unsigned32

read-only

The value of this object is calculated by this BGP Speaker as being; zero (0) - if this was the value sent by the peer and this value is permitted by this BGP Speaker. In this case, no keepalive messages are sent and the Hold Timer is not set. At least three (3). This value is the smaller of the value sent by this peer in the OPEN message and rcIpBgpTmpPeerAfHoldTimeConfigured for this peer. This value is only defined when the peering session is in the Established state.

U32 rcIpBgpTmpPeerAfKeepAlive

1.3.6.1.4.1.2272.1.8.101.17.10.3.3.1.2

Unsigned32

read-only

Time interval in seconds for the KeepAlive timer established with the peer. The value of this object is calculated by this BGP speaker such that, when compared with rcIpBgpTmpPeerAfHoldTime, it has the same proportion as what rcIpBgpTmpPeerAfKeepAliveConfigured has when compared with rcIpBgpTmpPeerAfHoldTimeConfigured. If the value of this object is zero (0), it indicates that the KeepAlive timer has not been established with the peer, or, the value of rcIpBgpTmpPeerAfKeepAliveConfigured is zero (0). This value is only defined when the peering session is in the Established state.

rcIpBgpTmpPeerAfCounters

1.3.6.1.4.1.2272.1.8.101.17.10.4

rcIpBgpTmpPeerAfCountersTable

1.3.6.1.4.1.2272.1.8.101.17.10.4.1

not-accessible

The counters associated with a BGP Peer.

rcIpBgpTmpPeerAfCountersEntry

1.3.6.1.4.1.2272.1.8.101.17.10.4.1.1

not-accessible

Each entry contains counters of message transmissions and FSM transitions for a given BGP Peering session.

C32 rcIpBgpTmpPeerAfInUpdates

1.3.6.1.4.1.2272.1.8.101.17.10.4.1.1.1

Counter32

read-only

The number of BGP UPDATE messages received on this connection.

C32 rcIpBgpTmpPeerAfOutUpdates

1.3.6.1.4.1.2272.1.8.101.17.10.4.1.1.2

Counter32

read-only

The number of BGP UPDATE messages transmitted on this connection.

C32 rcIpBgpTmpPeerAfInTotalMessages

1.3.6.1.4.1.2272.1.8.101.17.10.4.1.1.3

Counter32

read-only

The total number of messages received from the remote peer on this connection.

C32 rcIpBgpTmpPeerAfOutTotalMessages

1.3.6.1.4.1.2272.1.8.101.17.10.4.1.1.4

Counter32

read-only

The total number of messages transmitted to the remote peer on this connection.

C32 rcIpBgpTmpPeerAfFsmEstablishedTransitions

1.3.6.1.4.1.2272.1.8.101.17.10.4.1.1.5

Counter32

read-only

The total number of times the BGP FSM transitioned into the established state for this peer.

rcIpBgpTmpRib

1.3.6.1.4.1.2272.1.8.101.17.11

rcIpBgpTmpNlriTable

1.3.6.1.4.1.2272.1.8.101.17.11.1

not-accessible

The BGP-4 Received Path Attribute Table contains information about paths to destination networks received from all BGP4 peers. Collectively, this represents the Adj-Ribs-In. The route where rcIpBgpTmpNlriBest is true represents, for this NLRI, the route that is installed in the LocRib from the Adj-Ribs-In.

rcIpBgpTmpNlriEntry

1.3.6.1.4.1.2272.1.8.101.17.11.1.1

not-accessible

Information about a path to a network.

U32 rcIpBgpTmpNlriIndex

1.3.6.1.4.1.2272.1.8.101.17.11.1.1.1

Unsigned32

not-accessible

This index allows for multiple instances of a base prefix for a certain AFI-SAFI from a given peer. This is currently useful for two things: 1. Allowing for a peer in future implementations to send more than a single route instance. 2. Allow for extensions which extend the NLRI field to send the same prefix while utilizing other extension specific information. An example of this is RFC 3107 - Carrying MPLS labels in BGP.

ADR rcIpBgpTmpNlriAfi

1.3.6.1.4.1.2272.1.8.101.17.11.1.1.2

RcIpBgpTmpAddressFamilyIdentifierTC

not-accessible

The address family of the prefix for this NLRI. Note that the AFI is not necessarily equivalent to the an InetAddressType.

ADR rcIpBgpTmpNlriSafi

1.3.6.1.4.1.2272.1.8.101.17.11.1.1.3

RcIpBgpTmpSubsequentAddressFamilyIdentifierTC

not-accessible

The subsequent address family of the prefix for this NLRI

IPt rcIpBgpTmpNlriPrefixType

1.3.6.1.4.1.2272.1.8.101.17.11.1.1.4

InetAddressType

read-only

The type of the IP address prefix in the Network Layer Reachability Information field. The value of this object is derived from the appropriate value from the rcIpBgpTmpNlriAfi field. Where an appropriate InetAddressType is not available, the value of the object must be unknown(0).

IP rcIpBgpTmpNlriPrefix

1.3.6.1.4.1.2272.1.8.101.17.11.1.1.5

InetAddress

not-accessible

An IP address prefix in the Network Layer Reachability Information field. This object is an IP address containing the prefix with length specified by rcIpBgpTmpAfPathAttrAddrPrefixLen. Any bits beyond the length specified by rcIpBgpTmpAfPathAttrAddrPrefixLen are zeroed.

ADR rcIpBgpTmpNlriPrefixLen

1.3.6.1.4.1.2272.1.8.101.17.11.1.1.6

InetAddressPrefixLength

not-accessible

Length in bits of the address prefix in the Network Layer Reachability Information field.

T/F rcIpBgpTmpNlriBest

1.3.6.1.4.1.2272.1.8.101.17.11.1.1.7

TruthValue

read-only

An indication of whether or not this route was chosen as the best BGP4 route for this destination.

U32 rcIpBgpTmpNlriCalcLocalPref

1.3.6.1.4.1.2272.1.8.101.17.11.1.1.8

Unsigned32

read-only

The degree of preference calculated by the receiving BGP4 speaker for an advertised route. In the case where this prefix is ineligible, this object will be absent.

U32 rcIpBgpTmpAfPathAttrIndex

1.3.6.1.4.1.2272.1.8.101.17.11.1.1.9

Unsigned32

read-only

This value is a unique index for entries in the rcIpBgpTmpAfPathAttrTable. It is assigned by the agent at the point of creation of the rcIpBgpTmpAfPathAttrTable row entry. While its value is guaranteed to be unique at any time, it is otherwise opaque to the management application with respect to its value or the contiguity of rcIpBgpTmpAfPathAttrIndex row instance values across rows of the rcIpBgpTmpAfPathAttrTable. Note well that this index is used to distinguish unique sets of Path Attributes sent as part of BGP NLRI. The implementor is thus encouraged to make this index unique per set of all received path attributes. This value may be used to index tables in extension MIBs that share the property of belonging to the same received Path Attribute tuple.

U32 rcIpBgpTmpAfPathAttrUnknownIndex

1.3.6.1.4.1.2272.1.8.101.17.11.1.1.10

Unsigned32

read-only

This value is a unique index for entries in the rcIpBgpTmpAfPathAttrUnknownTable. It is assigned by the agent at the point of creation of the rcIpBgpTmpAfPathAttrUnknownTable row entry. While its value is guaranteed to be unique at any time, it is otherwise opaque to the management application with respect to its value or the contiguity of rcIpBgpTmpAfPathAttrUnknownIndex row instance values across rows of the rcIpBgpTmpAfPathAttrUnknownTable.

C32 rcIpBgpTmpAfPathAttrCounterEx

1.3.6.1.4.1.2272.1.8.101.17.11.3

Counter32

read-only

The number of entries in the rcIpBgpTmpAfPathAttrTable.

rcIpBgpTmpAfPathAttrTable

1.3.6.1.4.1.2272.1.8.101.17.11.4

not-accessible

Provides per advertised network-prefix attribute data, as advertised over a peering session.

rcIpBgpTmpAfPathAttrEntry

1.3.6.1.4.1.2272.1.8.101.17.11.4.1

not-accessible

Each entry contains data about path attributes associated with a given prefix in the rcIpBgpTmpNlriTable.

INT rcIpBgpTmpAfPathAttrOrigin

1.3.6.1.4.1.2272.1.8.101.17.11.4.1.1

INTEGER

read-only

The ultimate origin of the path information.

IPt rcIpBgpTmpAfPathAttrNextHopAddrType

1.3.6.1.4.1.2272.1.8.101.17.11.4.1.2

InetAddressType

read-only

The address family of the address for the border router that should be used to access the destination network.

IP rcIpBgpTmpAfPathAttrNextHopAddr

1.3.6.1.4.1.2272.1.8.101.17.11.4.1.3

InetAddress

read-only

The address of the border router that should be used to access the destination network. This address is the nexthop address received in the UPDATE packet associated with this prefix. Note that for RFC2545 style double nexthops, this object will always contain the global scope nexthop. bgpPathAttrLinkLocalNextHop will contain the linklocal scope nexthop, if it is present. In the case a mechanism is developed to use only a link local nexthop, rcIpBgpTmpAfPathAttrNextHopAddr will contain the link local nexthop.

IPt rcIpBgpTmpAfPathAttrLinkLocalNextHopAddrType

1.3.6.1.4.1.2272.1.8.101.17.11.4.1.4

InetAddressType

read-only

The address type for IPv6 link local addresses. This is present only when receiving RFC 2545 style double nexthops. This object is optionally present in BGP implementations that do not support IPv6.

IP rcIpBgpTmpAfPathAttrLinkLocalNextHopAddr

1.3.6.1.4.1.2272.1.8.101.17.11.4.1.5

InetAddress

read-only

This value contains an IPv6 link local address and is present only when receiving RFC 2545 style double nexthops. This object is optionally present in BGP implementations that do not support IPv6.

T/F rcIpBgpTmpAfPathAttrMedPresent

1.3.6.1.4.1.2272.1.8.101.17.11.4.1.6

TruthValue

read-only

This value is true when the MED value was sent in the UPDATE message.

U32 rcIpBgpTmpAfPathAttrMed

1.3.6.1.4.1.2272.1.8.101.17.11.4.1.7

Unsigned32

read-only

This metric is used to discriminate between multiple exit points to an adjacent autonomous system. When the MED value is absent but has a calculated default value, this object will contain the calculated value.

U32 rcIpBgpTmpAfPathAttrLocalPref

1.3.6.1.4.1.2272.1.8.101.17.11.4.1.8

Unsigned32

read-only

The originating BGP4 speakers degree of preference for an advertised route. If the route was not sent with a LOCAL_PREF value, this object will be absent.

INT rcIpBgpTmpAfPathAttrAtomicAggregate

1.3.6.1.4.1.2272.1.8.101.17.11.4.1.9

INTEGER

read-only

When this object is set to atomicAggregatePresent, the ATOMIC_AGGREGATE Path Attribute is present and indicates that the NLRI MUST NOT be made more specific.

INE rcIpBgpTmpAfPathAttrAggregatorAS

1.3.6.1.4.1.2272.1.8.101.17.11.4.1.10

InetAutonomousSystemNumber

read-only

The AS number of the last BGP4 speaker that performed route aggregation. If the AGGREGATOR path attribute is absent, this object will not be present in the conceptual row.

OID rcIpBgpTmpAfPathAttrAggregatorAddr

1.3.6.1.4.1.2272.1.8.101.17.11.4.1.11

RcIpBgpTmpIdentifierTC

read-only

The IP address of the last BGP4 speaker that performed route aggregation. If the AGGREGATOR path attribute is absent, this object will not be present in the conceptual row.

U32 rcIpBgpTmpAsPathCalcLength

1.3.6.1.4.1.2272.1.8.101.17.11.4.1.12

Unsigned32

read-only

This value represents the calculated length of the AS Path according to the rules of the BGP specification. This value is used in route selection.

U32 rcIpBgpTmpAsPathIndex

1.3.6.1.4.1.2272.1.8.101.17.11.4.1.13

Unsigned32

read-only

This value is a unique index for the decomposed AS Path in the rcIpBgpTmpAsPathTable. It is assigned by the agent at the point of creation of the rcIpBgpTmpAsPathTable row entry. While its value is guaranteed to be unique at any time, it is otherwise opaque to the management application with respect to its value or the contiguity of rcIpBgpTmpAsPathIndex row instance values across rows of the rcIpBgpTmpAsPathTable.

STR rcIpBgpTmpAsPathString

1.3.6.1.4.1.2272.1.8.101.17.11.4.1.14

SnmpAdminString

read-only

This is a string depicting the autonomous system path to this network which was received from the peer which advertised it. The format of the string is implementation-dependent, and should be designed for operator readability. Note that SnmpAdminString is only capable of representing a maximum of 255 characters. This may lead to the string being truncated in the presence of a large AS Path. The rcIpBgpTmpAsPathTable will give access to the full AS Path.

rcIpBgpTmpExtensions

1.3.6.1.4.1.2272.1.8.101.17.12

rcIpInterVrfStaticRoute

1.3.6.1.4.1.2272.1.8.103

I32 rcIpInterVrfStaticRouteTableSize

1.3.6.1.4.1.2272.1.8.103.1

Integer32

read-only

size of Ip Static Route Table.

rcIpInterVrfStaticRouteTable

1.3.6.1.4.1.2272.1.8.103.2

not-accessible

This table is used to add static IP routes to the device. Routes added into this table will automatically show-up in the 'rcIpRouteTable' when the device is actively using the route to forward IP traffic.

rcIpInterVrfStaticRouteEntry

1.3.6.1.4.1.2272.1.8.103.2.1

not-accessible

A static route to a particular destination.

OID rcIpInterVrfStaticRouteOwnerVrfId

1.3.6.1.4.1.2272.1.8.103.2.1.1

VrfIdentifier

not-accessible

Owner VRF id of the static route

IP rcIpInterVrfStaticRouteDest

1.3.6.1.4.1.2272.1.8.103.2.1.2

IpAddress

not-accessible

The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.

IP rcIpInterVrfStaticRouteMask

1.3.6.1.4.1.2272.1.8.103.2.1.3

IpAddress

not-accessible

Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the rcIpRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the rcIpRouteMask by determining whether the value of the correspondent rcIpRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the rcIpRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.

IP rcIpInterVrfStaticRouteNextHop

1.3.6.1.4.1.2272.1.8.103.2.1.4

IpAddress

not-accessible

The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface).

INT rcIpInterVrfStaticRouteMetric

1.3.6.1.4.1.2272.1.8.103.2.1.5

INTEGER

read-write

The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's rcIpRouteProto value. If this metric is not used, its value should be set to -1.

NUM rcIpInterVrfStaticRouteIfIndex

1.3.6.1.4.1.2272.1.8.103.2.1.6

InterfaceIndex

read-only

The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

INT rcIpInterVrfStaticRoutePreference

1.3.6.1.4.1.2272.1.8.103.2.1.7

INTEGER

read-write

Used to indicate the route preference of this entry. If there are more than one route that can be used to forward IP traffic, the route that has a highest preference will be used instead of a lower preference one. The higher the number, the higher the preference.

T/F rcIpInterVrfStaticRouteEnable

1.3.6.1.4.1.2272.1.8.103.2.1.8

TruthValue

read-write

Used to enable/disable this entry.

INT rcIpInterVrfStaticRouteStatus

1.3.6.1.4.1.2272.1.8.103.2.1.9

INTEGER

read-only

Used to indicate the current status of this entry.

ROW rcIpInterVrfStaticRouteRowStatus

1.3.6.1.4.1.2272.1.8.103.2.1.10

RowStatus

read-write

Used to create/delete entries

T/F rcIpInterVrfStaticRouteLocalNextHop

1.3.6.1.4.1.2272.1.8.103.2.1.11

TruthValue

read-write

Used to enable/disable this entry. True indicate that the static route becomes active only if switch has a local route to the network. False indicates that the static route becomes active if switch has a local route or dynamic route.

OID rcIpInterVrfStaticRouteNextHopVrfId

1.3.6.1.4.1.2272.1.8.103.2.1.12

VrfIdentifier

read-write

Used to indicate nhVrfId in inter-VRF static-route configuration

rcIpMulticastSquareSmlt

1.3.6.1.4.1.2272.1.8.109

T/F rcIpMulticastSquareSmltEnable

1.3.6.1.4.1.2272.1.8.109.1

TruthValue

read-write

Enable/Disable multicast Square Smlt.

rcArp

1.3.6.1.4.1.2272.1.9

I32 rcArpExtLifeTime

1.3.6.1.4.1.2272.1.9.1

Integer32

read-write

The lifetime in minutues of an ARP entry within the system.

rcArpExtTable

1.3.6.1.4.1.2272.1.9.2

not-accessible

ARP extension table. This table augments the standard ipNetToMediaTable defined in RFC1213.

rcArpExtEntry

1.3.6.1.4.1.2272.1.9.2.1

not-accessible

Entry containing Proprietary ARP information. An entry is automatically created in this table when an ip address is configured on an interface.

NUM rcArpExtEntIfIndex

1.3.6.1.4.1.2272.1.9.2.1.1

InterfaceIndex

read-only

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

INT rcArpExtEntDoProxy

1.3.6.1.4.1.2272.1.9.2.1.2

INTEGER

read-write

Enable or disable ARP proxy responses on the specified interface.

INT rcArpExtEntDoResp

1.3.6.1.4.1.2272.1.9.2.1.3

INTEGER

read-write

Enable or disable the sending of ARP responses on the specified interface.

INT rcArpExtEntDoFlood

1.3.6.1.4.1.2272.1.9.2.1.4

INTEGER

read-write

Enable or disable flooding of ARP responses for NLBS Virtual Mac on the specified interface.

rcRip

1.3.6.1.4.1.2272.1.10

INT rcRipExtOperation

1.3.6.1.4.1.2272.1.10.1

INTEGER

read-write

Enable or disable the operation of RIP on all Interfaces.

I32 rcRipExtUpdateTime

1.3.6.1.4.1.2272.1.10.2

Integer32

read-write

The time between transmission of RIP updates on all interfaces.

rcRipExtTable

1.3.6.1.4.1.2272.1.10.3

not-accessible

RIP extension table. This table augments the standard IfConfTable table in RFC1389.

rcRipExtEntry

1.3.6.1.4.1.2272.1.10.3.1

not-accessible

Entry containing Proprietary RIP information. An entry is automatically created in this table when an ip address is configured on an interface.

NUM rcRipExtEntIfIndex

1.3.6.1.4.1.2272.1.10.3.1.1

InterfaceIndex

read-only

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

INT rcRipExtEntTalk

1.3.6.1.4.1.2272.1.10.3.1.2

INTEGER

read-write

Enable or disable RIP transmission on the specified interface.

INT rcRipExtEntListen

1.3.6.1.4.1.2272.1.10.3.1.3

INTEGER

read-write

Enable or disable RIP reception on the specified interface.

INT rcRipExtEntPoison

1.3.6.1.4.1.2272.1.10.3.1.4

INTEGER

read-write

Enable or disable operation of poison reverse on the specified interface. If poison is disabled, split-horizon operation is enabled.

rcTest

1.3.6.1.4.1.2272.1.11

rcTestExtTable

1.3.6.1.4.1.2272.1.11.1

not-accessible

Test extension table. This table augments the standard ifTestTable table in RFC1573.

rcTestEntry

1.3.6.1.4.1.2272.1.11.1.1

not-accessible

Proprietary test variables.

NUM rcTestExtIfIndex

1.3.6.1.4.1.2272.1.11.1.1.1

InterfaceIndex

read-only

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

I32 rcTestExtPassCount

1.3.6.1.4.1.2272.1.11.1.1.2

Integer32

read-only

The number of iterations of the test case that completed successfully.

I32 rcTestExtFailCount

1.3.6.1.4.1.2272.1.11.1.1.3

Integer32

read-only

The number of iterations of the test case that failed.

rcTestTypes

1.3.6.1.4.1.2272.1.11.2

rcTestTypesFabric

1.3.6.1.4.1.2272.1.11.2.1

rcTestTypesArTable

1.3.6.1.4.1.2272.1.11.2.2

rcTestTypesExtLoopBack

1.3.6.1.4.1.2272.1.11.2.3

rcTestCodes

1.3.6.1.4.1.2272.1.11.3

rcTestCodesNoReceive

1.3.6.1.4.1.2272.1.11.3.1

rcTestCodesBadSeq

1.3.6.1.4.1.2272.1.11.3.2

rcTestCodesBadLen

1.3.6.1.4.1.2272.1.11.3.3

rcTestCodesBadData

1.3.6.1.4.1.2272.1.11.3.4

rcStat

1.3.6.1.4.1.2272.1.12

rcStatTable

1.3.6.1.4.1.2272.1.12.1

not-accessible

A table used to store port statistics.

rcStatEntry

1.3.6.1.4.1.2272.1.12.1.1

not-accessible

interface counters

NUM rcStatPortIndex

1.3.6.1.4.1.2272.1.12.1.1.1

InterfaceIndex

read-only

An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.

C32 rcStatFrameTooShorts

1.3.6.1.4.1.2272.1.12.1.1.2

Counter32

read-only

The total number of frames that are too short that were encountered on this interface.

C32 rcStatBridgeInUnicastFrames

1.3.6.1.4.1.2272.1.12.1.1.3

Counter32

read-only

The total number of incoming unicast frames that were bridged.

C32 rcStatBridgeInMulticastFrames

1.3.6.1.4.1.2272.1.12.1.1.4

Counter32

read-only

The total number of incoming multicast frames that were bridged.

C32 rcStatBridgeInBroadcastFrames

1.3.6.1.4.1.2272.1.12.1.1.5

Counter32

read-only

The total number of incoming broadcast frames that were bridged.

C32 rcStatBridgeInDiscards

1.3.6.1.4.1.2272.1.12.1.1.6

Counter32

read-only

The total number of frames that were discarded by the bridging entity.

C32 rcStatBridgeOutUnicastFrames

1.3.6.1.4.1.2272.1.12.1.1.7

Counter32

read-only

The total number of outgoing unicast frames that were bridged.

C32 rcStatBridgeOutMulticastFrames

1.3.6.1.4.1.2272.1.12.1.1.8

Counter32

read-only

The total number of outgoing multicast frames that were bridged.

C32 rcStatBridgeOutBroadcastFrames

1.3.6.1.4.1.2272.1.12.1.1.9

Counter32

read-only

The total number of outgoing broadcast frames that were bridged.

C32 rcStatRouteInUnicastFrames

1.3.6.1.4.1.2272.1.12.1.1.10

Counter32

read-only

The total number of incoming unicast frames that were routed.

C32 rcStatRouteInMulticastFrames

1.3.6.1.4.1.2272.1.12.1.1.11

Counter32

read-only

The total number of incoming multicast frames that were routed.

C32 rcStatRouteInDiscards

1.3.6.1.4.1.2272.1.12.1.1.12

Counter32

read-only

The total number of frames that were discarded by the routing entity.

C32 rcStatRouteOutUnicastFrames

1.3.6.1.4.1.2272.1.12.1.1.13

Counter32

read-only

The total number of outgoing unicast frames that were routed.

C32 rcStatRouteOutMulticastFrames

1.3.6.1.4.1.2272.1.12.1.1.14

Counter32

read-only

The total number of outgoing multicast frames that were routed.

C32 rcStatStgForwardTransitions

1.3.6.1.4.1.2272.1.12.1.1.15

Counter32

read-only

The number of times this port has transitioned from the Learning state to the Forwarding state.

C32 rcStatStgInConfigBpdus

1.3.6.1.4.1.2272.1.12.1.1.16

Counter32

read-only

C32 rcStatStgInTcnBpdus

1.3.6.1.4.1.2272.1.12.1.1.17

Counter32

read-only

C32 rcStatStgInBadBpdus

1.3.6.1.4.1.2272.1.12.1.1.18

Counter32

read-only

C32 rcStatStgOutConfigBpdus

1.3.6.1.4.1.2272.1.12.1.1.19

Counter32

read-only

C32 rcStatStgOutTcnBpdus

1.3.6.1.4.1.2272.1.12.1.1.20

Counter32

read-only

C32 rcStatBridgeOutFrames

1.3.6.1.4.1.2272.1.12.1.1.21

Counter32

read-only

Used by the Accelar 8000 product family to account for all transmitted bridge unicast, broadcast, and multicast packets. The individual counters are not supported.

C64 rcStatPolicerTotalBytes

1.3.6.1.4.1.2272.1.12.1.1.25

Counter64

read-only

The total number of bytes received on the interface.

C64 rcStatPolicerTotalPkts

1.3.6.1.4.1.2272.1.12.1.1.26

Counter64

read-only

The total number of packets received on the interface.

C64 rcStatPolicerGreenBytes

1.3.6.1.4.1.2272.1.12.1.1.27

Counter64

read-only

The total number of bytes received on the interface that were below the committed rate.

C64 rcStatPolicerYellowBytes

1.3.6.1.4.1.2272.1.12.1.1.28

Counter64

read-only

The total number of bytes received on the interface that were above the committed rate but below the peak rate.

C64 rcStatPolicerRedBytes

1.3.6.1.4.1.2272.1.12.1.1.29

Counter64

read-only

The total number of bytes received on the interface that were above the peak rate.

rcStatGigTable

1.3.6.1.4.1.2272.1.12.2

not-accessible

A table used to store Gigport error statistics.

rcStatGigEntry

1.3.6.1.4.1.2272.1.12.2.1

not-accessible

Gigabit interface error counters

NUM rcStatGigPortIndex

1.3.6.1.4.1.2272.1.12.2.1.1

InterfaceIndex

read-only

An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.

C32 rcStatGigLinkFailures

1.3.6.1.4.1.2272.1.12.2.1.2

Counter32

read-only

The total number of link failures encountered on this interface.

C32 rcStatGigPacketErrors

1.3.6.1.4.1.2272.1.12.2.1.3

Counter32

read-only

The total number of packet errors encountered on this interface.

C32 rcStatGigCarrierErrors

1.3.6.1.4.1.2272.1.12.2.1.4

Counter32

read-only

The total number of carrier errors encountered on this interface.

C32 rcStatGigLinkInactiveErrors

1.3.6.1.4.1.2272.1.12.2.1.5

Counter32

read-only

The total number of link inactive errors encountered on this interface.

C32 rcStatGigInFlowCtrlPkts

1.3.6.1.4.1.2272.1.12.2.1.6

Counter32

read-only

The total number of flow control packets received by this interface.

C32 rcStatGigOutFlowCtrlPkts

1.3.6.1.4.1.2272.1.12.2.1.7

Counter32

read-only

The total number of flow control packets transmitted by this interface.

C64 rcStatGigHCInPfcPkts

1.3.6.1.4.1.2272.1.12.2.1.8

Counter64

read-only

The total number of Priority Flow Control (PFC) packets received by this interface.

C64 rcStatGigHCOutPfcPkts

1.3.6.1.4.1.2272.1.12.2.1.9

Counter64

read-only

The total number of Priority Flow Control (PFC) packets transmitted by this interface.

C64 rcStatGigHCInFlowCtrlPkts

1.3.6.1.4.1.2272.1.12.2.1.10

Counter64

read-only

The total number of flow control packets received by this interface.

C64 rcStatGigHCOutFlowCtrlPkts

1.3.6.1.4.1.2272.1.12.2.1.11

Counter64

read-only

The total number of flow control packets transmitted by this interface.

rcStatOspf

1.3.6.1.4.1.2272.1.12.3

C32 rcStatOspfBuffersAllocated

1.3.6.1.4.1.2272.1.12.3.1

Counter32

read-only

Used to indicate the number of buffers allocated for OSPF.

C32 rcStatOspfBuffersFreed

1.3.6.1.4.1.2272.1.12.3.2

Counter32

read-only

Used to indicate the number of buffers that are freed by the OSPF.

C32 rcStatOspfBufferAllocFailures

1.3.6.1.4.1.2272.1.12.3.3

Counter32

read-only

Used to indicate the number of times that OSPF has failed to allocate buffers.

C32 rcStatOspfBufferFreeFailures

1.3.6.1.4.1.2272.1.12.3.4

Counter32

read-only

Used to indicate the number of times that OSPF has failed to free buffers.

C32 rcStatOspfTxPackets

1.3.6.1.4.1.2272.1.12.3.5

Counter32

read-only

Used to indicate the number of packets transmitted by OSPF.

C32 rcStatOspfRxPackets

1.3.6.1.4.1.2272.1.12.3.6

Counter32

read-only

Used to indicate the number of packets received by OSPF.

C32 rcStatOspfTxDropPackets

1.3.6.1.4.1.2272.1.12.3.7

Counter32

read-only

Used to indicate the number of packets dropped before transmitted by OSPF.

C32 rcStatOspfRxDropPackets

1.3.6.1.4.1.2272.1.12.3.8

Counter32

read-only

Used to indicate the number of packets dropped before received by OSPF.

C32 rcStatOspfRxBadPackets

1.3.6.1.4.1.2272.1.12.3.9

Counter32

read-only

Used to indicate the number of packets received by OSPF that are bad.

C32 rcStatOspfSpfRuns

1.3.6.1.4.1.2272.1.12.3.10

Counter32

read-only

Used to indicate the total number of SPF calculatations performed by OSPF, which also includes the number of partial route table calculation for Incremental Updates.

TIK rcStatOspfLastSpfRun

1.3.6.1.4.1.2272.1.12.3.11

TimeTicks

read-only

Used to indicate the time(SysUpTime) since the last spf calculated by OSPF.

C32 rcStatOspfLsdbTblSize

1.3.6.1.4.1.2272.1.12.3.12

Counter32

read-only

Used to indicate the number of entries in the linkstate database table.

C32 rcStatOspfRoutes

1.3.6.1.4.1.2272.1.12.3.13

Counter32

read-only

Used to indicate the number of OSPF routes added to RTM.

C32 rcStatOspfAdjacencies

1.3.6.1.4.1.2272.1.12.3.14

Counter32

read-only

Used to indicate the number of adjacencies existing.

C32 rcStatOspfAreas

1.3.6.1.4.1.2272.1.12.3.15

Counter32

read-only

Used to indicate the number of areas configured

rcStatIgmp

1.3.6.1.4.1.2272.1.12.4

C32 rcStatIgmpInMsgs

1.3.6.1.4.1.2272.1.12.4.1

Counter32

read-only

Used to indicate the number of Igmp packets received by the device.

C32 rcStatIgmpInErrors

1.3.6.1.4.1.2272.1.12.4.2

Counter32

read-only

Used to indicate the number of Igmp packets received that are with checksum errors.

C32 rcStatIgmpInQueries

1.3.6.1.4.1.2272.1.12.4.3

Counter32

read-only

Used to indicate the number of Igmp queries received by the device.

C32 rcStatIgmpInReports

1.3.6.1.4.1.2272.1.12.4.4

Counter32

read-only

Used to indicate the number of Igmp reports received by the device.

C32 rcStatIgmpInLeaves

1.3.6.1.4.1.2272.1.12.4.5

Counter32

read-only

Used to indicate the number of Igmp Leaves received by the device.

C32 rcStatIgmpInvalid

1.3.6.1.4.1.2272.1.12.4.6

Counter32

read-only

Used to indicate the number of Igmp packets received by the device that contained invalid type.

C32 rcStatIgmpOutMsgs

1.3.6.1.4.1.2272.1.12.4.7

Counter32

read-only

Used to indicate the number of Igmp queries sent by the device.

rcStatOspfIfTable

1.3.6.1.4.1.2272.1.12.5

not-accessible

A table used to store OSPF interface statistics.

rcStatOspfIfEntry

1.3.6.1.4.1.2272.1.12.5.1

not-accessible

Ospf interface statistics

NUM rcStatOspfIfIndex

1.3.6.1.4.1.2272.1.12.5.1.1

InterfaceIndexOrZero

read-only

An unique value that is used to identify a physical interface.

C32 rcStatOspfIfRxHellos

1.3.6.1.4.1.2272.1.12.5.1.2

Counter32

read-only

Used to indicate the number hello packets received by this interface.

C32 rcStatOspfIfRxDBDescrs

1.3.6.1.4.1.2272.1.12.5.1.3

Counter32

read-only

Used to indicate the number database descriptor packets received by this interface.

C32 rcStatOspfIfRxLSUpdates

1.3.6.1.4.1.2272.1.12.5.1.4

Counter32

read-only

Used to indicate the number Link state update packets received by this interface.

C32 rcStatOspfIfRxLSReqs

1.3.6.1.4.1.2272.1.12.5.1.5

Counter32

read-only

Used to indicate the number Link state request packets received by this interface.

C32 rcStatOspfIfRxLSAcks

1.3.6.1.4.1.2272.1.12.5.1.6

Counter32

read-only

Used to indicate the number Link state acknowlege packets received by this interface.

C32 rcStatOspfIfTxHellos

1.3.6.1.4.1.2272.1.12.5.1.7

Counter32

read-only

Used to indicate the number hello packets transmitted by this interface.

C32 rcStatOspfIfTxDBDescrs

1.3.6.1.4.1.2272.1.12.5.1.8

Counter32

read-only

Used to indicate the number database descriptor packets transmitted by this interface.

C32 rcStatOspfIfTxLSUpdates

1.3.6.1.4.1.2272.1.12.5.1.9

Counter32

read-only

Used to indicate the number Link state update packets transmitted by this interface.

C32 rcStatOspfIfTxLSReqs

1.3.6.1.4.1.2272.1.12.5.1.10

Counter32

read-only

Used to indicate the number Link state request packets transmitted by this interface.

C32 rcStatOspfIfTxLSAcks

1.3.6.1.4.1.2272.1.12.5.1.11

Counter32

read-only

Used to indicate the number Link state acknowlege packets transmitted by this interface.

C32 rcStatOspfIfVersionMismatches

1.3.6.1.4.1.2272.1.12.5.1.12

Counter32

read-only

Used to indicate the number version mismatches received by this interface.

C32 rcStatOspfIfAreaMismatches

1.3.6.1.4.1.2272.1.12.5.1.13

Counter32

read-only

Used to indicate the number area mismatches received by this interface.

C32 rcStatOspfIfAuthTypeMismatches

1.3.6.1.4.1.2272.1.12.5.1.14

Counter32

read-only

Used to indicate the number AuthType mismatches received by this interface.

C32 rcStatOspfIfAuthFailures

1.3.6.1.4.1.2272.1.12.5.1.15

Counter32

read-only

Used to indicate the number Authentication failures.

C32 rcStatOspfIfNetMaskMismatches

1.3.6.1.4.1.2272.1.12.5.1.16

Counter32

read-only

Used to indicate the number net mask mismatches received by this interface.

C32 rcStatOspfIfHelloIntervalMismatches

1.3.6.1.4.1.2272.1.12.5.1.17

Counter32

read-only

Used to indicate the number hello interval mismatches received by this interface.

C32 rcStatOspfIfDeadIntervalMismatches

1.3.6.1.4.1.2272.1.12.5.1.18

Counter32

read-only

Used to indicate the number dead interval mismatches received by this interface.

C32 rcStatOspfIfOptionMismatches

1.3.6.1.4.1.2272.1.12.5.1.19

Counter32

read-only

Used to indicate the number options mismatches received by this interface.

rcStatMlt

1.3.6.1.4.1.2272.1.12.6

rcStatMltIfExtnTable

1.3.6.1.4.1.2272.1.12.6.1

not-accessible

A table used to store Mlt interface statistics.

rcStatMltIfExtnEntry

1.3.6.1.4.1.2272.1.12.6.1.1

not-accessible

Mlt interface statistics

INT rcStatMltIfExtnMltId

1.3.6.1.4.1.2272.1.12.6.1.1.1

INTEGER

read-only

Mlt Id

C32 rcStatMltIfExtnIfInMulticastPkts

1.3.6.1.4.1.2272.1.12.6.1.1.2

Counter32

read-only

multi-pkts to upper

C32 rcStatMltIfExtnIfInBroadcastPkts

1.3.6.1.4.1.2272.1.12.6.1.1.3

Counter32

read-only

broad-pkts to upper

C32 rcStatMltIfExtnIfOutMulticastPkts

1.3.6.1.4.1.2272.1.12.6.1.1.4

Counter32

read-only

multi-pkts from upper

C32 rcStatMltIfExtnIfOutBroadcastPkts

1.3.6.1.4.1.2272.1.12.6.1.1.5

Counter32

read-only

broad-pkts from upper

C64 rcStatMltIfExtnIfHCInOctets

1.3.6.1.4.1.2272.1.12.6.1.1.6

Counter64

read-only

The total number of octets received on the MLT interface, including framing characters.

C64 rcStatMltIfExtnIfHCInUcastPkts

1.3.6.1.4.1.2272.1.12.6.1.1.7

Counter64

read-only

The number of packets delivered by this MLT to a higher MLT that were not addressed to a nulticast or broadcase address at this sublayer.

C64 rcStatMltIfExtnIfHCInMulticastPkt

1.3.6.1.4.1.2272.1.12.6.1.1.8

Counter64

read-only

The number of packets delivered to this MLT that were addressed to a nulticast address at this sublayer. For a MAC layer protocol, this number includes both Group and Functional addresses.

C64 rcStatMltIfExtnIfHCInBroadcastPkt

1.3.6.1.4.1.2272.1.12.6.1.1.9

Counter64

read-only

The number of packets delivered to this MLT that were addressed to a broadcast address at this sublayer.

C64 rcStatMltIfExtnIfHCOutOctets

1.3.6.1.4.1.2272.1.12.6.1.1.10

Counter64

read-only

The total number of octets transmitted out of the MLT interface, including framing characters.

C64 rcStatMltIfExtnIfHCOutUcastPkts

1.3.6.1.4.1.2272.1.12.6.1.1.11

Counter64

read-only

The number of packets that hight-level protocols requested be transmitted that were not addressed to a multicast address at this MLT. This total number includes those packets discarded or unsent.

C64 rcStatMltIfExtnIfHCOutMulticast

1.3.6.1.4.1.2272.1.12.6.1.1.12

Counter64

read-only

The total number of packets that hight-level protocols requested be transmitted, and that were addressed to a multicast address at this MLT, including those that were discarded or not sent. For a MAC layer protocol, this number includes both Group and Functional addresses.

C64 rcStatMltIfExtnIfHCOutBroadcast

1.3.6.1.4.1.2272.1.12.6.1.1.13

Counter64

read-only

The total number of packets that hight-level protocols requested be transmitted, and that were addressed to a broadcase address at this MLT, including those that were discarded or not sent.

C64 rcStatMltIfExtnIfHCInLsmPkts

1.3.6.1.4.1.2272.1.12.6.1.1.14

Counter64

read-only

The total number of Link State Messaging (LSM) packets delivered to this MLT.

C64 rcStatMltIfExtnIfHCOutLsmPkts

1.3.6.1.4.1.2272.1.12.6.1.1.15

Counter64

read-only

The total number of Link State Messaging (LSM) packets trasmitted on this MLT.

rcStatMltEtherTable

1.3.6.1.4.1.2272.1.12.6.2

not-accessible

A table used to store Mlt Ethernet statistics.

rcStatMltEtherEntry

1.3.6.1.4.1.2272.1.12.6.2.1

not-accessible

Mlt enternet statistics

INT rcStatMltEtherMltId

1.3.6.1.4.1.2272.1.12.6.2.1.1

INTEGER

read-only

A value that uniquely identifies the Multi-Link Trunk associated with this entry.

C32 rcStatMltEtherAlignmentErrors

1.3.6.1.4.1.2272.1.12.6.2.1.2

Counter32

read-only

A count of frames received on a particular MLT that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions occur are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.

C32 rcStatMltEtherFCSErrors

1.3.6.1.4.1.2272.1.12.6.2.1.3

Counter32

read-only

A count of frames received on an MLT that are an integral number of octets in length but do not pass the FCS check. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions occur are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.

C32 rcStatMltEtherSingleCollFrames

1.3.6.1.4.1.2272.1.12.6.2.1.4

Counter32

read-only

A count of successfully transmitted frames on a particular MLT for which transmission is inhibited by exactly one collision. A frame that is counted by an instance of this objects is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and it not counted by the corresponding instance of the MultipleCollisionFrames object.

C32 rcStatMltEtherMultipleCollFrames

1.3.6.1.4.1.2272.1.12.6.2.1.5

Counter32

read-only

A count of successfully transmitted frames on a particular MLT for which transmission is inhibited by more than one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the SingleCollisionFrames objects.

C32 rcStatMltEtherSQETestError

1.3.6.1.4.1.2272.1.12.6.2.1.6

Counter32

read-only

A count of times that the SQE TEST ERROR message is generated by the PLS sublayer for a particular MLT. SQE stands for Signal Quality Error.

C32 rcStatMltEtherDeferredTransmiss

1.3.6.1.4.1.2272.1.12.6.2.1.7

Counter32

read-only

A count of frames for which the first transmission attempt on a particular MLT is delayed because the medium is busy. The count represented by an instance of this object does not include frames involved in collisions.

C32 rcStatMltEtherLateCollisions

1.3.6.1.4.1.2272.1.12.6.2.1.8

Counter32

read-only

The number of times that a collision is detected on a particular MLT later than 512 bit-times (64 octets) into the transmission of a packet. Five hundred and twelve bit-times corresponds to 51.2 microseconds on a 10 mb/s system. A (late) collision included in a count represented by an instance of this object is also considered as a (generic) collision for purposes of other collision-related statistics.

C32 rcStatMltEtherExcessiveCollis

1.3.6.1.4.1.2272.1.12.6.2.1.9

Counter32

read-only

A count of frames for which transmission on a particular MLT fails due to excessive collisions.

C32 rcStatMltEtherIMacTransmitError

1.3.6.1.4.1.2272.1.12.6.2.1.10

Counter32

read-only

A count of frames for which transmission on a particular MLT fails due to an internal MAC sublayer transmit error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the LateCollisions object, the ExcessiveCollisions object, or the CarrierSenseError object.

C32 rcStatMltEtherCarrierSenseError

1.3.6.1.4.1.2272.1.12.6.2.1.11

Counter32

read-only

The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame on a particular MLT. The count represented by an instance of this object is incremented at most once per transmission attempt, even if the carrier sense condition fluctuates during a transmission attempt.

C32 rcStatMltEtherFrameTooLong

1.3.6.1.4.1.2272.1.12.6.2.1.12

Counter32

read-only

A count of frames received on a particular MLT that exceed the maximum permitted size (1518 octets). The count represented by an instance os this object is incremented when the frame TooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions occur are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.

C32 rcStatMltEtherIMacReceiveError

1.3.6.1.4.1.2272.1.12.6.2.1.13

Counter32

read-only

A count of frames for which reception on a particular MLT fails due to an internal MAC sublayer receive error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the FrameTooLongs object, the AlignmentErrors object, of the FCSErrors objects. The precise meaning of the count represented by an instance of this object is implementation specific. In particular, an instance of this object may represent a count of receive errors on a particular interface that are not otherwise counted.

C32 rcStatSmltIstDownCnt

1.3.6.1.4.1.2272.1.12.6.4

Counter32

read-only

Counters that counts how the session between the two peering switches has done down since last boot.

C32 rcStatSmltHelloTxMsgCnt

1.3.6.1.4.1.2272.1.12.6.5

Counter32

read-only

Counters that counts the tx hello msg.

C32 rcStatSmltHelloRxMsgCnt

1.3.6.1.4.1.2272.1.12.6.6

Counter32

read-only

Counters that counts the rx hello msg.

C32 rcStatSmltLearnMacAddrTxMsgCnt

1.3.6.1.4.1.2272.1.12.6.7

Counter32

read-only

Counters that counts the tx learn Mac Address msg.

C32 rcStatSmltLearnMacAddrRxMsgCnt

1.3.6.1.4.1.2272.1.12.6.8

Counter32

read-only

Counters that counts the rx learn Mac Address msg.

C32 rcStatSmltMacAddrAgeOutTxMsgCnt

1.3.6.1.4.1.2272.1.12.6.9

Counter32

read-only

Counters that counts the tx Mac Address Aging Out msg.

C32 rcStatSmltMacAddrAgeOutRxMsgCnt

1.3.6.1.4.1.2272.1.12.6.10

Counter32

read-only

Counters that counts the rx Mac Address Aging Out msg.

C32 rcStatSmltMacAddrAgeExpTxMsgCnt

1.3.6.1.4.1.2272.1.12.6.11

Counter32

read-only

Counters that counts the tx Mac Address age expired msg.

C32 rcStatSmltMacAddrAgeExpRxMsgCnt

1.3.6.1.4.1.2272.1.12.6.12

Counter32

read-only

Counters that counts the rx Mac Address age expired msg.

C32 rcStatSmltStgInfoTxMsgCnt

1.3.6.1.4.1.2272.1.12.6.13

Counter32

read-only

Counters that counts the tx Stg information msg.

C32 rcStatSmltStgInfoRxMsgCnt

1.3.6.1.4.1.2272.1.12.6.14

Counter32

read-only

Counters that counts the rx Stg information msg.

C32 rcStatSmltDelMacAddrTxMsgCnt

1.3.6.1.4.1.2272.1.12.6.15

Counter32

read-only

Counters that counts the tx deleted MAC address msg.

C32 rcStatSmltDelMacAddrRxMsgCnt

1.3.6.1.4.1.2272.1.12.6.16

Counter32

read-only

Counters that counts the rx deleted MAC address msg.

C32 rcStatSmltSmltDownTxMsgCnt

1.3.6.1.4.1.2272.1.12.6.17

Counter32

read-only

Counters that counts the tx Smlt Down msg.

C32 rcStatSmltSmltDownRxMsgCnt

1.3.6.1.4.1.2272.1.12.6.18

Counter32

read-only

Counters that counts the rx Smlt Down msg.

C32 rcStatSmltSmltUpTxMsgCnt

1.3.6.1.4.1.2272.1.12.6.19

Counter32

read-only

Counters that counts the tx Smlt Up msg.

C32 rcStatSmltSmltUpRxMsgCnt

1.3.6.1.4.1.2272.1.12.6.20

Counter32

read-only

Counters that counts the rx Smlt Up msg.

C32 rcStatSmltSendMacTblTxMsgCnt

1.3.6.1.4.1.2272.1.12.6.21

Counter32

read-only

Counters that counts the tx Send Mac Table msg.

C32 rcStatSmltSendMacTblRxMsgCnt

1.3.6.1.4.1.2272.1.12.6.22

Counter32

read-only

Counters that counts the rx Send Mac Table msg.

C32 rcStatSmltIgmpTxMsgCnt

1.3.6.1.4.1.2272.1.12.6.23

Counter32

read-only

Counters that counts the tx Igmp msg.

C32 rcStatSmltIgmpRxMsgCnt

1.3.6.1.4.1.2272.1.12.6.24

Counter32

read-only

Counters that counts the rx Igmp msg.

C32 rcStatSmltPortDownTxMsgCnt

1.3.6.1.4.1.2272.1.12.6.25

Counter32

read-only

Counters that counts the tx port down msg.

C32 rcStatSmltPortDownRxMsgCnt

1.3.6.1.4.1.2272.1.12.6.26

Counter32

read-only

Counters that counts the rx port down msg.

C32 rcStatSmltReqMacTblTxMsgCnt

1.3.6.1.4.1.2272.1.12.6.27

Counter32

read-only

Counters that counts the tx request Mac table msg.

C32 rcStatSmltReqMacTblRxMsgCnt

1.3.6.1.4.1.2272.1.12.6.28

Counter32

read-only

Counters that counts the rx request Mac table msg.

C32 rcStatSmltRxUnknownMsgTypeCnt

1.3.6.1.4.1.2272.1.12.6.29

Counter32

read-only

Counters that counts the rx unknown msg type.

rcStatMulticast

1.3.6.1.4.1.2272.1.12.9

C32 rcStatMulticastSourceGroupThresholdExceeded

1.3.6.1.4.1.2272.1.12.9.1

Counter32

read-only

The count of number of times the threshold of available IP Multicast (Source,Group) Records was reached. When this threshold is reached, a new IP Multicast stream ingressing the switch cannot be forwarded.

C32 rcStatMulticastEgressStreamThresholdExceeded

1.3.6.1.4.1.2272.1.12.9.2

Counter32

read-only

The count of number of times the threshold of available IP Multicast Egress Forwarding Records was reached. When this threshold is reached, a new IP Multicast Receiver that needs new Egress Forwarding Record (PepStrem Record) will not be programmed to receive the subscribing multicast stream.

rcStatBgp

1.3.6.1.4.1.2272.1.12.10

C32 rcStatBgpStarts

1.3.6.1.4.1.2272.1.12.10.1

Counter32

read-only

Number of times BGP connection started

C32 rcStatBgpStops

1.3.6.1.4.1.2272.1.12.10.2

Counter32

read-only

Number of times BGP connection stopped

C32 rcStatBgpOpens

1.3.6.1.4.1.2272.1.12.10.3

Counter32

read-only

Number of times BGP opens TCP

C32 rcStatBgpCloses

1.3.6.1.4.1.2272.1.12.10.4

Counter32

read-only

Number of times BGP closes TCP

C32 rcStatBgpFails

1.3.6.1.4.1.2272.1.12.10.5

Counter32

read-only

Number of times TCP attempts failed

C32 rcStatBgpFatals

1.3.6.1.4.1.2272.1.12.10.6

Counter32

read-only

Number of times TCP crashes due to fatal error

C32 rcStatBgpConnExps

1.3.6.1.4.1.2272.1.12.10.7

Counter32

read-only

Number of times TCP retry timer expired

C32 rcStatBgpHoldExps

1.3.6.1.4.1.2272.1.12.10.8

Counter32

read-only

Number of times hold timer expired

C32 rcStatBgpKeepExps

1.3.6.1.4.1.2272.1.12.10.9

Counter32

read-only

Number of times keepalive timer expired

C32 rcStatBgpRxOpens

1.3.6.1.4.1.2272.1.12.10.10

Counter32

read-only

Number of OPENs BGP receives

C32 rcStatBgpRxKeeps

1.3.6.1.4.1.2272.1.12.10.11

Counter32

read-only

Number of KEEPALIVEs BGP recieves

C32 rcStatBgpRxUpdates

1.3.6.1.4.1.2272.1.12.10.12

Counter32

read-only

Number of UPDATEs BGP recieves

C32 rcStatBgpRxNotifys

1.3.6.1.4.1.2272.1.12.10.13

Counter32

read-only

Number NOTIFICATIONs BGP recieves

C32 rcStatBgpTxOpens

1.3.6.1.4.1.2272.1.12.10.14

Counter32

read-only

Number of OPENs BGP transmitted

C32 rcStatBgpTxKeeps

1.3.6.1.4.1.2272.1.12.10.15

Counter32

read-only

Number of KEEPALIVEs BGP transmitted

C32 rcStatBgpTxUpdates

1.3.6.1.4.1.2272.1.12.10.16

Counter32

read-only

Number of UPDATEs BGP transmits

C32 rcStatBgpTxNotifys

1.3.6.1.4.1.2272.1.12.10.17

Counter32

read-only

Number of NOTIFICATIONs BGP transmits

C32 rcStatBgpBadEvents

1.3.6.1.4.1.2272.1.12.10.18

Counter32

read-only

Number of invalid events FSM received

C32 rcStatBgpSyncFails

1.3.6.1.4.1.2272.1.12.10.19

Counter32

read-only

Number of times FDB sync failed

C32 rcStatBgpTrEvent

1.3.6.1.4.1.2272.1.12.10.20

Counter32

read-only

Trace event

C32 rcStatBgpRxECodeHeader

1.3.6.1.4.1.2272.1.12.10.21

Counter32

read-only

Total Header errors received

C32 rcStatBgpRxECodeOpen

1.3.6.1.4.1.2272.1.12.10.22

Counter32

read-only

Total Open errors received

C32 rcStatBgpRxECodeUpdate

1.3.6.1.4.1.2272.1.12.10.23

Counter32

read-only

Total Update errors received

C32 rcStatBgpRxECodeHoldtimer

1.3.6.1.4.1.2272.1.12.10.24

Counter32

read-only

Total Holdtimer errors received

C32 rcStatBgpRxECodeFSM

1.3.6.1.4.1.2272.1.12.10.25

Counter32

read-only

Total FSM errors received

C32 rcStatBgpRxECodeCease

1.3.6.1.4.1.2272.1.12.10.26

Counter32

read-only

Total Cease errors received

C32 rcStatBgpRxHdrCodeNoSync

1.3.6.1.4.1.2272.1.12.10.27

Counter32

read-only

Header Not Synchronized errors received

C32 rcStatBgpRxHdrCodeInvalidMsgLen

1.3.6.1.4.1.2272.1.12.10.28

Counter32

read-only

Header Invalid msg len errors received

C32 rcStatBgpRxHdrCodeInvalidMsgType

1.3.6.1.4.1.2272.1.12.10.29

Counter32

read-only

Header Invalid msg type errors received

C32 rcStatBgpRxOpCodeBadVer

1.3.6.1.4.1.2272.1.12.10.30

Counter32

read-only

Open errors received: Bad Version

C32 rcStatBgpRxOpCodeBadAs

1.3.6.1.4.1.2272.1.12.10.31

Counter32

read-only

Open errors received: Bad AS Number

C32 rcStatBgpRxOpCodeBadRtID

1.3.6.1.4.1.2272.1.12.10.32

Counter32

read-only

Open errors received: Bad BGP Rtr ID

C32 rcStatBgpRxOpCodeUnsuppOption

1.3.6.1.4.1.2272.1.12.10.33

Counter32

read-only

Open errors received: Unsupported Option

C32 rcStatBgpRxOpCodeAuthFail

1.3.6.1.4.1.2272.1.12.10.34

Counter32

read-only

Open errors received: Auth Failures

C32 rcStatBgpRxOpCodeBadHold

1.3.6.1.4.1.2272.1.12.10.35

Counter32

read-only

Open errors received: Bad Hold Value

C32 rcStatBgpRxUpdCodeMalformedAttrList

1.3.6.1.4.1.2272.1.12.10.36

Counter32

read-only

Update errors received:Malformed Attr List

C32 rcStatBgpRxUpdCodeWelknownAttrUnrecog

1.3.6.1.4.1.2272.1.12.10.37

Counter32

read-only

Update errors received: Welknown Attr Unrecog

C32 rcStatBgpRxUpdCodeWelknownAttrMiss

1.3.6.1.4.1.2272.1.12.10.38

Counter32

read-only

Update errors received: Welknown Attr Missing

C32 rcStatBgpRxUpdCodeAttrFlagError

1.3.6.1.4.1.2272.1.12.10.39

Counter32

read-only

Update errors received: Attr Flag Error

C32 rcStatBgpRxUpdCodeAttrLenError

1.3.6.1.4.1.2272.1.12.10.40

Counter32

read-only

Update errors received: Attr Len Error

C32 rcStatBgpRxUpdCodeBadORIGINAttr

1.3.6.1.4.1.2272.1.12.10.41

Counter32

read-only

Update errors received: Bad ORIGIN Attr

C32 rcStatBgpRxUpdCodeASRoutingLoop

1.3.6.1.4.1.2272.1.12.10.42

Counter32

read-only

Update errors received: AS Routing Loop

C32 rcStatBgpRxUpdCodeBadNHAttr

1.3.6.1.4.1.2272.1.12.10.43

Counter32

read-only

Update errors received: Bad NEXT-HOP Attr

C32 rcStatBgpRxUpdCodeOptionalAttrError

1.3.6.1.4.1.2272.1.12.10.44

Counter32

read-only

Update errors received: Optional Attr Error

C32 rcStatBgpRxUpdCodeBadNetworkField

1.3.6.1.4.1.2272.1.12.10.45

Counter32

read-only

Update errors received: Bad Network Field

C32 rcStatBgpRxUpdCodeMalformedASPath

1.3.6.1.4.1.2272.1.12.10.46

Counter32

read-only

Update errors received: Malformed AS Path

C32 rcStatBgpTxECodeHeader

1.3.6.1.4.1.2272.1.12.10.47

Counter32

read-only

Total Header errors transmitted

C32 rcStatBgpTxECodeOpen

1.3.6.1.4.1.2272.1.12.10.48

Counter32

read-only

Total Open errors transmitted

C32 rcStatBgpTxECodeUpdate

1.3.6.1.4.1.2272.1.12.10.49

Counter32

read-only

Total Update errors transmitted

C32 rcStatBgpTxECodeHoldtimer

1.3.6.1.4.1.2272.1.12.10.50

Counter32

read-only

Total Holdtimer errors transmitted

C32 rcStatBgpTxECodeFSM

1.3.6.1.4.1.2272.1.12.10.51

Counter32

read-only

Total FSM errors transmitted

C32 rcStatBgpTxECodeCease

1.3.6.1.4.1.2272.1.12.10.52

Counter32

read-only

Total Cease errors transmitted

C32 rcStatBgpTxHdrCodeNoSync

1.3.6.1.4.1.2272.1.12.10.53

Counter32

read-only

Header Not Synchronized errors transmitted

C32 rcStatBgpTxHdrCodeInvalidMsgLen

1.3.6.1.4.1.2272.1.12.10.54

Counter32

read-only

Header Invalid msg len errors transmitted

C32 rcStatBgpTxHdrCodeInvalidMsgType

1.3.6.1.4.1.2272.1.12.10.55

Counter32

read-only

Header Invalid msg type errors transmitted

C32 rcStatBgpTxOpCodeBadVer

1.3.6.1.4.1.2272.1.12.10.56

Counter32

read-only

Open errors transmitted: Bad Version

C32 rcStatBgpTxOpCodeBadAs

1.3.6.1.4.1.2272.1.12.10.57

Counter32

read-only

Open errors transmitted: Bad AS Number

C32 rcStatBgpTxOpCodeBadRtID

1.3.6.1.4.1.2272.1.12.10.58

Counter32

read-only

Open errors transmitted: Bad BGP Rtr ID

C32 rcStatBgpTxOpCodeUnsuppOption

1.3.6.1.4.1.2272.1.12.10.59

Counter32

read-only

Open errors transmitted: Unsupported Option

C32 rcStatBgpTxOpCodeAuthFail

1.3.6.1.4.1.2272.1.12.10.60

Counter32

read-only

Open errors transmitted: Auth Failures

C32 rcStatBgpTxOpCodeBadHold

1.3.6.1.4.1.2272.1.12.10.61

Counter32

read-only

Open errors transmitted: Bad Hold Value

C32 rcStatBgpTxUpdCodeMalformedAttrList

1.3.6.1.4.1.2272.1.12.10.62

Counter32

read-only

Update errors transmitted:Malformed Attr List

C32 rcStatBgpTxUpdCodeWelknownAttrUnrecog

1.3.6.1.4.1.2272.1.12.10.63

Counter32

read-only

Update errors transmitted: Welknown Attr Unrecog

C32 rcStatBgpTxUpdCodeWelknownAttrMiss

1.3.6.1.4.1.2272.1.12.10.64

Counter32

read-only

Update errors transmitted: Welknown Attr Missing

C32 rcStatBgpTxUpdCodeAttrFlagError

1.3.6.1.4.1.2272.1.12.10.65

Counter32

read-only

Update errors transmitted: Attr Flag Error

C32 rcStatBgpTxUpdCodeAttrLenError

1.3.6.1.4.1.2272.1.12.10.66

Counter32

read-only

Update errors transmitted: Attr Len Error

C32 rcStatBgpTxUpdCodeBadORIGINAttr

1.3.6.1.4.1.2272.1.12.10.67

Counter32

read-only

Update errors transmitted: Bad ORIGIN Attr

C32 rcStatBgpTxUpdCodeASRoutingLoop

1.3.6.1.4.1.2272.1.12.10.68

Counter32

read-only

Update errors transmitted: AS Routing Loop

C32 rcStatBgpTxUpdCodeBadNHAttr

1.3.6.1.4.1.2272.1.12.10.69

Counter32

read-only

Update errors transmitted: Bad NEXT-HOP Attr

C32 rcStatBgpTxUpdCodeOptionalAttrError

1.3.6.1.4.1.2272.1.12.10.70

Counter32

read-only

Update errors transmitted: Optional Attr Error

C32 rcStatBgpTxUpdCodeBadNetworkField

1.3.6.1.4.1.2272.1.12.10.71

Counter32

read-only

Update errors transmitted: Bad Network Field

C32 rcStatBgpTxUpdCodeMalformedASPath

1.3.6.1.4.1.2272.1.12.10.72

Counter32

read-only

Update errors transmitted: Malformed AS Path

ENA rcStatBgpReset

1.3.6.1.4.1.2272.1.12.10.73

EnableValue

read-write

reset Bgp global stats

rcStatBgpPeerTable

1.3.6.1.4.1.2272.1.12.11

not-accessible

A table used to store Bgp Peer statistics.

rcStatBgpPeerEntry

1.3.6.1.4.1.2272.1.12.11.1

not-accessible

Bgp Peer statistics

IP rcStatBgpPeerAddr

1.3.6.1.4.1.2272.1.12.11.1.1

IpAddress

read-only

C32 rcStatBgpPeerStarts

1.3.6.1.4.1.2272.1.12.11.1.2

Counter32

read-only

Number of times peer BGP connection started

C32 rcStatBgpPeerStops

1.3.6.1.4.1.2272.1.12.11.1.3

Counter32

read-only

Number of times peer BGP connection stopped

C32 rcStatBgpPeerOpens

1.3.6.1.4.1.2272.1.12.11.1.4

Counter32

read-only

Number of times peer opens TCP

C32 rcStatBgpPeerCloses

1.3.6.1.4.1.2272.1.12.11.1.5

Counter32

read-only

Number of times peer closes TCP

C32 rcStatBgpPeerFails

1.3.6.1.4.1.2272.1.12.11.1.6

Counter32

read-only

Number of times peer TCP attempts failed

C32 rcStatBgpPeerFatals

1.3.6.1.4.1.2272.1.12.11.1.7

Counter32

read-only

Number of times peer TCP crashes due to fatal error

C32 rcStatBgpPeerConnExps

1.3.6.1.4.1.2272.1.12.11.1.8

Counter32

read-only

Number of times peer TCP retry timer expired

C32 rcStatBgpPeerHoldExps

1.3.6.1.4.1.2272.1.12.11.1.9

Counter32

read-only

Number of times peer hold timer expired

C32 rcStatBgpPeerKeepExps

1.3.6.1.4.1.2272.1.12.11.1.10

Counter32

read-only

Number of times peer keepalive timer expired

C32 rcStatBgpPeerTxMsgs

1.3.6.1.4.1.2272.1.12.11.1.11

Counter32

read-only

Total messages send by the peer

C32 rcStatBgpPeerTxOpens

1.3.6.1.4.1.2272.1.12.11.1.12

Counter32

read-only

Opens sent by the peer

C32 rcStatBgpPeerTxKeeps

1.3.6.1.4.1.2272.1.12.11.1.13

Counter32

read-only

Keepalives sent by the peer

C32 rcStatBgpPeerTxUpdates

1.3.6.1.4.1.2272.1.12.11.1.14

Counter32

read-only

Updates sent by the peer

C32 rcStatBgpPeerTxNotifys

1.3.6.1.4.1.2272.1.12.11.1.15

Counter32

read-only

Notifications sent by the peer

C32 rcStatBgpPeerRxMsgs

1.3.6.1.4.1.2272.1.12.11.1.16

Counter32

read-only

Total messages received by the peer

C32 rcStatBgpPeerRxInCompPkts

1.3.6.1.4.1.2272.1.12.11.1.17

Counter32

read-only

Incomplete message received by the peer

C32 rcStatBgpPeerRxOpens

1.3.6.1.4.1.2272.1.12.11.1.18

Counter32

read-only

Opens received by the peer

C32 rcStatBgpPeerRxKeeps

1.3.6.1.4.1.2272.1.12.11.1.19

Counter32

read-only

Keepalives received by the peer

C32 rcStatBgpPeerRxUpdates

1.3.6.1.4.1.2272.1.12.11.1.20

Counter32

read-only

Updates received by the peer

C32 rcStatBgpPeerRxNotifys

1.3.6.1.4.1.2272.1.12.11.1.21

Counter32

read-only

Notifications received by the peer

C32 rcStatBgpPeerBadEvents

1.3.6.1.4.1.2272.1.12.11.1.22

Counter32

read-only

Number of invalid events received by the peer

C32 rcStatBgpPeerSyncFails

1.3.6.1.4.1.2272.1.12.11.1.23

Counter32

read-only

Number of times FDB sync failed of the peer

C32 rcStatBgpPeerRcvdTooShort

1.3.6.1.4.1.2272.1.12.11.1.24

Counter32

read-only

Number of messages recieved by the peer that is too sho rt

C32 rcStatBgpPeerNoMarker

1.3.6.1.4.1.2272.1.12.11.1.25

Counter32

read-only

Number of messages without marker recieved by the peer

C32 rcStatBgpPeerDropped

1.3.6.1.4.1.2272.1.12.11.1.26

Counter32

read-only

Number of messages the peer has dropped

C32 rcStatBgpPeerBadMsgTypes

1.3.6.1.4.1.2272.1.12.11.1.27

Counter32

read-only

Number of messages with invalid message type

C32 rcStatBgpPeerTrEvent

1.3.6.1.4.1.2272.1.12.11.1.28

Counter32

read-only

Peer trace event

C32 rcStatBgpPeerTxRoutes

1.3.6.1.4.1.2272.1.12.11.1.29

Counter32

read-only

Number of NLRI sent by peer

C32 rcStatBgpPeerRxRoutesAdded

1.3.6.1.4.1.2272.1.12.11.1.30

Counter32

read-only

Number of routes added into loc_rib by this peer

C32 rcStatBgpPeerRxRoutesReplaced

1.3.6.1.4.1.2272.1.12.11.1.31

Counter32

read-only

Number of routes replaced by the routes received by the peer

C32 rcStatBgpPeerRxNlri

1.3.6.1.4.1.2272.1.12.11.1.32

Counter32

read-only

Number of NLRI received by the peer

C32 rcStatBgpPeerRxValidUpdates

1.3.6.1.4.1.2272.1.12.11.1.33

Counter32

read-only

Number of valid UPDATEs received by the peer

C32 rcStatBgpPeerRxECodeHeader

1.3.6.1.4.1.2272.1.12.11.1.34

Counter32

read-only

Total errors peer received: Header

C32 rcStatBgpPeerRxECodeOpen

1.3.6.1.4.1.2272.1.12.11.1.35

Counter32

read-only

Total errors peer received: Open

C32 rcStatBgpPeerRxECodeUpdate

1.3.6.1.4.1.2272.1.12.11.1.36

Counter32

read-only

Total errors peer received: Update

C32 rcStatBgpPeerRxECodeHoldtimer

1.3.6.1.4.1.2272.1.12.11.1.37

Counter32

read-only

Total errors peer received: Hold

C32 rcStatBgpPeerRxECodeFSM

1.3.6.1.4.1.2272.1.12.11.1.38

Counter32

read-only

Total errors peer received: Fsm

C32 rcStatBgpPeerRxECodeCease

1.3.6.1.4.1.2272.1.12.11.1.39

Counter32

read-only

Total errors peer received: Cease

C32 rcStatBgpPeerRxHdrCodeNoSync

1.3.6.1.4.1.2272.1.12.11.1.40

Counter32

read-only

Header errors peer received: Not Synchronized

C32 rcStatBgpPeerRxHdrCodeInvalidMsgLen

1.3.6.1.4.1.2272.1.12.11.1.41

Counter32

read-only

Header errors peer received: Invalid message length

C32 rcStatBgpPeerRxHdrCodeInvalidMsgType

1.3.6.1.4.1.2272.1.12.11.1.42

Counter32

read-only

Header errors peer received: Invalid message type

C32 rcStatBgpPeerRxOpCodeBadVer

1.3.6.1.4.1.2272.1.12.11.1.43

Counter32

read-only

Open errors peer received: Bad Version

C32 rcStatBgpPeerRxOpCodeBadAs

1.3.6.1.4.1.2272.1.12.11.1.44

Counter32

read-only

Open errors peer received: Bad AS number

C32 rcStatBgpPeerRxOpCodeBadRtID

1.3.6.1.4.1.2272.1.12.11.1.45

Counter32

read-only

Open errors peer received: Bad BGP ID

C32 rcStatBgpPeerRxOpCodeUnsuppOption

1.3.6.1.4.1.2272.1.12.11.1.46

Counter32

read-only

Open errors peer received: Unsupported Options

C32 rcStatBgpPeerRxOpCodeAuthFail

1.3.6.1.4.1.2272.1.12.11.1.47

Counter32

read-only

Open errors peer received: Authorization failures

C32 rcStatBgpPeerRxOpCodeBadHold

1.3.6.1.4.1.2272.1.12.11.1.48

Counter32

read-only

Open errors peer received: Bad Hold value

C32 rcStatBgpPeerRxUpdCodeMalformedAttrList

1.3.6.1.4.1.2272.1.12.11.1.49

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerRxUpdCodeWelknownAttrUnrecog

1.3.6.1.4.1.2272.1.12.11.1.50

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerRxUpdCodeWelknownAttrMiss

1.3.6.1.4.1.2272.1.12.11.1.51

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerRxUpdCodeAttrFlagError

1.3.6.1.4.1.2272.1.12.11.1.52

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerRxUpdCodeAttrLenError

1.3.6.1.4.1.2272.1.12.11.1.53

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerRxUpdCodeBadORIGINAttr

1.3.6.1.4.1.2272.1.12.11.1.54

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerRxUpdCodeASRoutingLoop

1.3.6.1.4.1.2272.1.12.11.1.55

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerRxUpdCodeBadNHAttr

1.3.6.1.4.1.2272.1.12.11.1.56

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerRxUpdCodeOptionalAttrError

1.3.6.1.4.1.2272.1.12.11.1.57

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerRxUpdCodeBadNetworkField

1.3.6.1.4.1.2272.1.12.11.1.58

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerRxUpdCodeMalformedASPath

1.3.6.1.4.1.2272.1.12.11.1.59

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerTxECodeHeader

1.3.6.1.4.1.2272.1.12.11.1.60

Counter32

read-only

Total errors peer received: Header

C32 rcStatBgpPeerTxECodeOpen

1.3.6.1.4.1.2272.1.12.11.1.61

Counter32

read-only

Total errors peer received: Open

C32 rcStatBgpPeerTxECodeUpdate

1.3.6.1.4.1.2272.1.12.11.1.62

Counter32

read-only

Total errors peer received: Update

C32 rcStatBgpPeerTxECodeHoldtimer

1.3.6.1.4.1.2272.1.12.11.1.63

Counter32

read-only

Total errors peer received: Hold

C32 rcStatBgpPeerTxECodeFSM

1.3.6.1.4.1.2272.1.12.11.1.64

Counter32

read-only

Total errors peer received: Fsm

C32 rcStatBgpPeerTxECodeCease

1.3.6.1.4.1.2272.1.12.11.1.65

Counter32

read-only

Total errors peer received: Cease

C32 rcStatBgpPeerTxHdrCodeNoSync

1.3.6.1.4.1.2272.1.12.11.1.66

Counter32

read-only

Header errors peer received: Not Synchronized

C32 rcStatBgpPeerTxHdrCodeInvalidMsgLen

1.3.6.1.4.1.2272.1.12.11.1.67

Counter32

read-only

Header errors peer received: Invalid message length

C32 rcStatBgpPeerTxHdrCodeInvalidMsgType

1.3.6.1.4.1.2272.1.12.11.1.68

Counter32

read-only

Header errors peer received: Invalid message type

C32 rcStatBgpPeerTxOpCodeBadVer

1.3.6.1.4.1.2272.1.12.11.1.69

Counter32

read-only

Open errors peer received: Bad Version

C32 rcStatBgpPeerTxOpCodeBadAs

1.3.6.1.4.1.2272.1.12.11.1.70

Counter32

read-only

Open errors peer received: Bad AS number

C32 rcStatBgpPeerTxOpCodeBadRtID

1.3.6.1.4.1.2272.1.12.11.1.71

Counter32

read-only

Open errors peer received: Bad BGP ID

C32 rcStatBgpPeerTxOpCodeUnsuppOption

1.3.6.1.4.1.2272.1.12.11.1.72

Counter32

read-only

Open errors peer received: Unsupported Options

C32 rcStatBgpPeerTxOpCodeAuthFail

1.3.6.1.4.1.2272.1.12.11.1.73

Counter32

read-only

Open errors peer received: Authorization failures

C32 rcStatBgpPeerTxOpCodeBadHold

1.3.6.1.4.1.2272.1.12.11.1.74

Counter32

read-only

Open errors peer received: Bad Hold value

C32 rcStatBgpPeerTxUpdCodeMalformedAttrList

1.3.6.1.4.1.2272.1.12.11.1.75

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerTxUpdCodeWelknownAttrUnrecog

1.3.6.1.4.1.2272.1.12.11.1.76

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerTxUpdCodeWelknownAttrMiss

1.3.6.1.4.1.2272.1.12.11.1.77

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerTxUpdCodeAttrFlagError

1.3.6.1.4.1.2272.1.12.11.1.78

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerTxUpdCodeAttrLenError

1.3.6.1.4.1.2272.1.12.11.1.79

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerTxUpdCodeBadORIGINAttr

1.3.6.1.4.1.2272.1.12.11.1.80

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerTxUpdCodeASRoutingLoop

1.3.6.1.4.1.2272.1.12.11.1.81

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerTxUpdCodeBadNHAttr

1.3.6.1.4.1.2272.1.12.11.1.82

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerTxUpdCodeOptionalAttrError

1.3.6.1.4.1.2272.1.12.11.1.83

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerTxUpdCodeBadNetworkField

1.3.6.1.4.1.2272.1.12.11.1.84

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerTxUpdCodeMalformedASPath

1.3.6.1.4.1.2272.1.12.11.1.85

Counter32

read-only

Update errors peer received: Malformed Attr List

ENA rcStatBgpPeerReset

1.3.6.1.4.1.2272.1.12.11.1.86

EnableValue

read-write

reset peer stats

rcStatBgpPeerAfTable

1.3.6.1.4.1.2272.1.12.13

not-accessible

A table used to store v4/v6 Bgp Peer statistics.

rcStatBgpPeerAfEntry

1.3.6.1.4.1.2272.1.12.13.1

not-accessible

AF independent Bgp Peer statistics

IPt rcStatBgpPeerAfAddrType

1.3.6.1.4.1.2272.1.12.13.1.1

InetAddressType

not-accessible

Inet address type of the AF independent peer

IP rcStatBgpPeerAfAddr

1.3.6.1.4.1.2272.1.12.13.1.2

InetAddress

not-accessible

Inet address of the AF independent peer

C32 rcStatBgpPeerAfStarts

1.3.6.1.4.1.2272.1.12.13.1.3

Counter32

read-only

Number of times peer BGP connection started

C32 rcStatBgpPeerAfStops

1.3.6.1.4.1.2272.1.12.13.1.4

Counter32

read-only

Number of times peer BGP connection stopped

C32 rcStatBgpPeerAfOpens

1.3.6.1.4.1.2272.1.12.13.1.5

Counter32

read-only

Number of times peer opens TCP

C32 rcStatBgpPeerAfCloses

1.3.6.1.4.1.2272.1.12.13.1.6

Counter32

read-only

Number of times peer closes TCP

C32 rcStatBgpPeerAfFails

1.3.6.1.4.1.2272.1.12.13.1.7

Counter32

read-only

Number of times peer TCP attempts failed

C32 rcStatBgpPeerAfFatals

1.3.6.1.4.1.2272.1.12.13.1.8

Counter32

read-only

Number of times peer TCP crashes due to fatal error

C32 rcStatBgpPeerAfConnExps

1.3.6.1.4.1.2272.1.12.13.1.9

Counter32

read-only

Number of times peer TCP retry timer expired

C32 rcStatBgpPeerAfHoldExps

1.3.6.1.4.1.2272.1.12.13.1.10

Counter32

read-only

Number of times peer hold timer expired

C32 rcStatBgpPeerAfKeepExps

1.3.6.1.4.1.2272.1.12.13.1.11

Counter32

read-only

Number of times peer keepalive timer expired

C32 rcStatBgpPeerAfTxMsgs

1.3.6.1.4.1.2272.1.12.13.1.12

Counter32

read-only

Total messages send by the peer

C32 rcStatBgpPeerAfTxOpens

1.3.6.1.4.1.2272.1.12.13.1.13

Counter32

read-only

Opens sent by the peer

C32 rcStatBgpPeerAfTxKeeps

1.3.6.1.4.1.2272.1.12.13.1.14

Counter32

read-only

Keepalives sent by the peer

C32 rcStatBgpPeerAfTxUpdates

1.3.6.1.4.1.2272.1.12.13.1.15

Counter32

read-only

Updates sent by the peer

C32 rcStatBgpPeerAfTxNotifys

1.3.6.1.4.1.2272.1.12.13.1.16

Counter32

read-only

Notifications sent by the peer

C32 rcStatBgpPeerAfRxMsgs

1.3.6.1.4.1.2272.1.12.13.1.17

Counter32

read-only

Total messages received by the peer

C32 rcStatBgpPeerAfRxInCompPkts

1.3.6.1.4.1.2272.1.12.13.1.18

Counter32

read-only

Incomplete message received by the peer

C32 rcStatBgpPeerAfRxOpens

1.3.6.1.4.1.2272.1.12.13.1.19

Counter32

read-only

Opens received by the peer

C32 rcStatBgpPeerAfRxKeeps

1.3.6.1.4.1.2272.1.12.13.1.20

Counter32

read-only

Keepalives received by the peer

C32 rcStatBgpPeerAfRxUpdates

1.3.6.1.4.1.2272.1.12.13.1.21

Counter32

read-only

Updates received by the peer

C32 rcStatBgpPeerAfRxNotifys

1.3.6.1.4.1.2272.1.12.13.1.22

Counter32

read-only

Notifications received by the peer

C32 rcStatBgpPeerAfBadEvents

1.3.6.1.4.1.2272.1.12.13.1.23

Counter32

read-only

Number of invalid events received by the peer

C32 rcStatBgpPeerAfSyncFails

1.3.6.1.4.1.2272.1.12.13.1.24

Counter32

read-only

Number of times FDB sync failed of the peer

C32 rcStatBgpPeerAfRcvdTooShort

1.3.6.1.4.1.2272.1.12.13.1.25

Counter32

read-only

Number of messages recieved by the peer that is too sho rt

C32 rcStatBgpPeerAfNoMarker

1.3.6.1.4.1.2272.1.12.13.1.26

Counter32

read-only

Number of messages without marker recieved by the peer

C32 rcStatBgpPeerAfDropped

1.3.6.1.4.1.2272.1.12.13.1.27

Counter32

read-only

Number of messages the peer has dropped

C32 rcStatBgpPeerAfBadMsgTypes

1.3.6.1.4.1.2272.1.12.13.1.28

Counter32

read-only

Number of messages with invalid message type

C32 rcStatBgpPeerAfTrEvent

1.3.6.1.4.1.2272.1.12.13.1.29

Counter32

read-only

Peer trace event

C32 rcStatBgpPeerAfTxRoutes

1.3.6.1.4.1.2272.1.12.13.1.30

Counter32

read-only

Number of NLRI sent by peer

C32 rcStatBgpPeerAfRxRoutesAdded

1.3.6.1.4.1.2272.1.12.13.1.31

Counter32

read-only

Number of routes added into loc_rib by this peer

C32 rcStatBgpPeerAfRxRoutesReplaced

1.3.6.1.4.1.2272.1.12.13.1.32

Counter32

read-only

Number of routes replaced by the routes received by the peer

C32 rcStatBgpPeerAfRxNlri

1.3.6.1.4.1.2272.1.12.13.1.33

Counter32

read-only

Number of NLRI received by the peer

C32 rcStatBgpPeerAfRxValidUpdates

1.3.6.1.4.1.2272.1.12.13.1.34

Counter32

read-only

Number of valid UPDATEs received by the peer

C32 rcStatBgpPeerAfRxECodeHeader

1.3.6.1.4.1.2272.1.12.13.1.35

Counter32

read-only

Total errors peer received: Header

C32 rcStatBgpPeerAfRxECodeOpen

1.3.6.1.4.1.2272.1.12.13.1.36

Counter32

read-only

Total errors peer received: Open

C32 rcStatBgpPeerAfRxECodeUpdate

1.3.6.1.4.1.2272.1.12.13.1.37

Counter32

read-only

Total errors peer received: Update

C32 rcStatBgpPeerAfRxECodeHoldtimer

1.3.6.1.4.1.2272.1.12.13.1.38

Counter32

read-only

Total errors peer received: Hold

C32 rcStatBgpPeerAfRxECodeFSM

1.3.6.1.4.1.2272.1.12.13.1.39

Counter32

read-only

Total errors peer received: Fsm

C32 rcStatBgpPeerAfRxECodeCease

1.3.6.1.4.1.2272.1.12.13.1.40

Counter32

read-only

Total errors peer received: Cease

C32 rcStatBgpPeerAfRxHdrCodeNoSync

1.3.6.1.4.1.2272.1.12.13.1.41

Counter32

read-only

Header errors peer received: Not Synchronized

C32 rcStatBgpPeerAfRxHdrCodeInvalidMsgLen

1.3.6.1.4.1.2272.1.12.13.1.42

Counter32

read-only

Header errors peer received: Invalid message length

C32 rcStatBgpPeerAfRxHdrCodeInvalidMsgType

1.3.6.1.4.1.2272.1.12.13.1.43

Counter32

read-only

Header errors peer received: Invalid message type

C32 rcStatBgpPeerAfRxOpCodeBadVer

1.3.6.1.4.1.2272.1.12.13.1.44

Counter32

read-only

Open errors peer received: Bad Version

C32 rcStatBgpPeerAfRxOpCodeBadAs

1.3.6.1.4.1.2272.1.12.13.1.45

Counter32

read-only

Open errors peer received: Bad AS number

C32 rcStatBgpPeerAfRxOpCodeBadRtID

1.3.6.1.4.1.2272.1.12.13.1.46

Counter32

read-only

Open errors peer received: Bad BGP ID

C32 rcStatBgpPeerAfRxOpCodeUnsuppOption

1.3.6.1.4.1.2272.1.12.13.1.47

Counter32

read-only

Open errors peer received: Unsupported Options

C32 rcStatBgpPeerAfRxOpCodeAuthFail

1.3.6.1.4.1.2272.1.12.13.1.48

Counter32

read-only

Open errors peer received: Authorization failures

C32 rcStatBgpPeerAfRxOpCodeBadHold

1.3.6.1.4.1.2272.1.12.13.1.49

Counter32

read-only

Open errors peer received: Bad Hold value

C32 rcStatBgpPeerAfRxUpdCodeMalformedAttrList

1.3.6.1.4.1.2272.1.12.13.1.50

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfRxUpdCodeWelknownAttrUnrecog

1.3.6.1.4.1.2272.1.12.13.1.51

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfRxUpdCodeWelknownAttrMiss

1.3.6.1.4.1.2272.1.12.13.1.52

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfRxUpdCodeAttrFlagError

1.3.6.1.4.1.2272.1.12.13.1.53

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfRxUpdCodeAttrLenError

1.3.6.1.4.1.2272.1.12.13.1.54

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfRxUpdCodeBadORIGINAttr

1.3.6.1.4.1.2272.1.12.13.1.55

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfRxUpdCodeASRoutingLoop

1.3.6.1.4.1.2272.1.12.13.1.56

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfRxUpdCodeBadNHAttr

1.3.6.1.4.1.2272.1.12.13.1.57

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfRxUpdCodeOptionalAttrError

1.3.6.1.4.1.2272.1.12.13.1.58

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfRxUpdCodeBadNetworkField

1.3.6.1.4.1.2272.1.12.13.1.59

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfRxUpdCodeMalformedASPath

1.3.6.1.4.1.2272.1.12.13.1.60

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfTxECodeHeader

1.3.6.1.4.1.2272.1.12.13.1.61

Counter32

read-only

Total errors peer received: Header

C32 rcStatBgpPeerAfTxECodeOpen

1.3.6.1.4.1.2272.1.12.13.1.62

Counter32

read-only

Total errors peer received: Open

C32 rcStatBgpPeerAfTxECodeUpdate

1.3.6.1.4.1.2272.1.12.13.1.63

Counter32

read-only

Total errors peer received: Update

C32 rcStatBgpPeerAfTxECodeHoldtimer

1.3.6.1.4.1.2272.1.12.13.1.64

Counter32

read-only

Total errors peer received: Hold

C32 rcStatBgpPeerAfTxECodeFSM

1.3.6.1.4.1.2272.1.12.13.1.65

Counter32

read-only

Total errors peer received: Fsm

C32 rcStatBgpPeerAfTxECodeCease

1.3.6.1.4.1.2272.1.12.13.1.66

Counter32

read-only

Total errors peer received: Cease

C32 rcStatBgpPeerAfTxHdrCodeNoSync

1.3.6.1.4.1.2272.1.12.13.1.67

Counter32

read-only

Header errors peer received: Not Synchronized

C32 rcStatBgpPeerAfTxHdrCodeInvalidMsgLen

1.3.6.1.4.1.2272.1.12.13.1.68

Counter32

read-only

Header errors peer received: Invalid message length

C32 rcStatBgpPeerAfTxHdrCodeInvalidMsgType

1.3.6.1.4.1.2272.1.12.13.1.69

Counter32

read-only

Header errors peer received: Invalid message type

C32 rcStatBgpPeerAfTxOpCodeBadVer

1.3.6.1.4.1.2272.1.12.13.1.70

Counter32

read-only

Open errors peer received: Bad Version

C32 rcStatBgpPeerAfTxOpCodeBadAs

1.3.6.1.4.1.2272.1.12.13.1.71

Counter32

read-only

Open errors peer received: Bad AS number

C32 rcStatBgpPeerAfTxOpCodeBadRtID

1.3.6.1.4.1.2272.1.12.13.1.72

Counter32

read-only

Open errors peer received: Bad BGP ID

C32 rcStatBgpPeerAfTxOpCodeUnsuppOption

1.3.6.1.4.1.2272.1.12.13.1.73

Counter32

read-only

Open errors peer received: Unsupported Options

C32 rcStatBgpPeerAfTxOpCodeAuthFail

1.3.6.1.4.1.2272.1.12.13.1.74

Counter32

read-only

Open errors peer received: Authorization failures

C32 rcStatBgpPeerAfTxOpCodeBadHold

1.3.6.1.4.1.2272.1.12.13.1.75

Counter32

read-only

Open errors peer received: Bad Hold value

C32 rcStatBgpPeerAfTxUpdCodeMalformedAttrList

1.3.6.1.4.1.2272.1.12.13.1.76

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfTxUpdCodeWelknownAttrUnrecog

1.3.6.1.4.1.2272.1.12.13.1.77

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfTxUpdCodeWelknownAttrMiss

1.3.6.1.4.1.2272.1.12.13.1.78

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfTxUpdCodeAttrFlagError

1.3.6.1.4.1.2272.1.12.13.1.79

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfTxUpdCodeAttrLenError

1.3.6.1.4.1.2272.1.12.13.1.80

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfTxUpdCodeBadORIGINAttr

1.3.6.1.4.1.2272.1.12.13.1.81

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfTxUpdCodeASRoutingLoop

1.3.6.1.4.1.2272.1.12.13.1.82

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfTxUpdCodeBadNHAttr

1.3.6.1.4.1.2272.1.12.13.1.83

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfTxUpdCodeOptionalAttrError

1.3.6.1.4.1.2272.1.12.13.1.84

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfTxUpdCodeBadNetworkField

1.3.6.1.4.1.2272.1.12.13.1.85

Counter32

read-only

Update errors peer received: Malformed Attr List

C32 rcStatBgpPeerAfTxUpdCodeMalformedASPath

1.3.6.1.4.1.2272.1.12.13.1.86

Counter32

read-only

Update errors peer received: Malformed Attr List

T/F rcStatBgpPeerAfReset

1.3.6.1.4.1.2272.1.12.13.1.87

TruthValue

read-create

reset peer stats

rcStg

1.3.6.1.4.1.2272.1.13

I32 rcStgMaxStgs

1.3.6.1.4.1.2272.1.13.1

Integer32

read-write

The maximum number of spanning tree groups this device can support concurrently.

I32 rcStgNumStgs

1.3.6.1.4.1.2272.1.13.2

Integer32

read-only

The number of spanning tree groups that are currently defined.

POR rcStgUnassignedPorts

1.3.6.1.4.1.2272.1.13.3

PortSet

read-only

A bitfield used to identify which ports in the system currently not assigned to any STG. The bitfield is 32 octets long representing ports 0 to 255 (inclusive).

rcStgTable

1.3.6.1.4.1.2272.1.13.4

not-accessible

A table used to store Spanning Tree Group (STG) information. Each row in the table specifies a different STG in the device.

rcStgEntry

1.3.6.1.4.1.2272.1.13.4.1

not-accessible

STG attributes

INT rcStgId

1.3.6.1.4.1.2272.1.13.4.1.1

INTEGER

read-only

An identifier used to identify a STG in the device.

MAC rcStgTaggedBpduAddress

1.3.6.1.4.1.2272.1.13.4.1.2

MacAddress

read-write

The MAC address to be assigned to the destination mac address field in tagged BPDUs. The default address is the well known multicast group address 01-80-c2-00-00-00.

I32 rcStgTaggedBpduVlanId

1.3.6.1.4.1.2272.1.13.4.1.3

Integer32

read-write

The VLAN ID to be used for tagging BPDUs.

MAC rcStgBridgeAddress

1.3.6.1.4.1.2272.1.13.4.1.4

MacAddress

read-only

The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with rcStgPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol.

I32 rcStgNumPorts

1.3.6.1.4.1.2272.1.13.4.1.5

Integer32

read-only

The number of ports controlled by this bridging entity.

INT rcStgProtocolSpecification

1.3.6.1.4.1.2272.1.13.4.1.6

INTEGER

read-only

An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.

INT rcStgPriority

1.3.6.1.4.1.2272.1.13.4.1.7

INTEGER

read-write

The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of rcStgBridgeAddress.

TIK rcStgTimeSinceTopologyChange

1.3.6.1.4.1.2272.1.13.4.1.8

TimeTicks

read-only

The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.

C32 rcStgTopChanges

1.3.6.1.4.1.2272.1.13.4.1.9

Counter32

read-only

The total number of topology changes detected by this bridge since the management entity was last reset or initialized.

BRI rcStgDesignatedRoot

1.3.6.1.4.1.2272.1.13.4.1.10

BridgeId

read-only

The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.

I32 rcStgRootCost

1.3.6.1.4.1.2272.1.13.4.1.11

Integer32

read-only

The cost of the path to the root as seen from this bridge.

NUM rcStgRootPort

1.3.6.1.4.1.2272.1.13.4.1.12

InterfaceIndex

read-only

The port number of the port which offers the lowest cost path from this bridge to the root bridge.

TIM rcStgMaxAge

1.3.6.1.4.1.2272.1.13.4.1.13

Timeout

read-only

The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.

TIM rcStgHelloTime

1.3.6.1.4.1.2272.1.13.4.1.14

Timeout

read-only

The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.

I32 rcStgHoldTime

1.3.6.1.4.1.2272.1.13.4.1.15

Integer32

read-only

This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.

TIM rcStgForwardDelay

1.3.6.1.4.1.2272.1.13.4.1.16

Timeout

read-only

This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to rcStgBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]

TIM rcStgBridgeMaxAge

1.3.6.1.4.1.2272.1.13.4.1.17

Timeout

read-write

The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of rcStgBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.

TIM rcStgBridgeHelloTime

1.3.6.1.4.1.2272.1.13.4.1.18

Timeout

read-write

The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.

TIM rcStgBridgeForwardDelay

1.3.6.1.4.1.2272.1.13.4.1.19

Timeout

read-write

The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of rcStgBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.

T/F rcStgEnableStp

1.3.6.1.4.1.2272.1.13.4.1.20

TruthValue

read-write

Indicate whether the spanning tree protocol should be active in this STG.

T/F rcStgStpTrapEnable

1.3.6.1.4.1.2272.1.13.4.1.21

TruthValue

read-write

Indicate whether traps relating to the spanning tree protocol should be sent for this STG.

OCT rcStgPortMembers

1.3.6.1.4.1.2272.1.13.4.1.22

OCTET STRING

read-write

A bitfield used to identify which ports in the system are members this STG. The bitfield is 104 octets long representing ports 64 (1/1) to 831 (12/68) (inclusive).

ROW rcStgRowStatus

1.3.6.1.4.1.2272.1.13.4.1.23

RowStatus

read-write

Row status.

OCT rcStgPortStpState

1.3.6.1.4.1.2272.1.13.4.1.24

OCTET STRING

read-only

Every 2 bitfields used to identify a port state in this STG. Port state is cataloged as non-stp(0), blocking(1), learning(2), and forwarding(3).

rcStgPortTable

1.3.6.1.4.1.2272.1.13.5

not-accessible

A table used to store Spanning Tree Group (STG) port related information. If a port is associated with more than one STGs, the port will have one entry in this table for each STG it assigned to.

rcStgPortEntry

1.3.6.1.4.1.2272.1.13.5.1

not-accessible

STG Port attributes

NUM rcStgPort

1.3.6.1.4.1.2272.1.13.5.1.1

InterfaceIndex

read-only

The port number of the port for which this entry contains Spanning Tree Protocol management information.

INT rcStgPortStgId

1.3.6.1.4.1.2272.1.13.5.1.2

INTEGER

read-only

The STG identifier this port is assigned to.

INT rcStgPortPriority

1.3.6.1.4.1.2272.1.13.5.1.3

INTEGER

read-write

The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of rcStgPort. The original range is 0..255. VSP9000 supports range is 0..240 with increament of 16

INT rcStgPortState

1.3.6.1.4.1.2272.1.13.5.1.4

INTEGER

read-only

The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see rcStgPortEnable), this object will have a value of disabled(1).

T/F rcStgPortEnableStp

1.3.6.1.4.1.2272.1.13.5.1.5

TruthValue

read-write

The enabled/disabled status of the port.

T/F rcStgPortFastStart

1.3.6.1.4.1.2272.1.13.5.1.6

TruthValue

read-write

When this flag is set, the port is moved straight to the forwarding(5) state upon being enabled.

INT rcStgPortPathCost

1.3.6.1.4.1.2272.1.13.5.1.7

INTEGER

read-write

The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.

BRI rcStgPortDesignatedRoot

1.3.6.1.4.1.2272.1.13.5.1.8

BridgeId

read-only

The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.

I32 rcStgPortDesignatedCost

1.3.6.1.4.1.2272.1.13.5.1.9

Integer32

read-only

The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.

BRI rcStgPortDesignatedBridge

1.3.6.1.4.1.2272.1.13.5.1.10

BridgeId

read-only

The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.

OCT rcStgPortDesignatedPort

1.3.6.1.4.1.2272.1.13.5.1.11

OCTET STRING

read-only

The Port Identifier of the port on the Designated Bridge for this port's segment.

C32 rcStgPortForwardTransitions

1.3.6.1.4.1.2272.1.13.5.1.12

Counter32

read-only

The number of times this port has transitioned from the Learning state to the Forwarding state.

C32 rcStgPortInConfigBpdus

1.3.6.1.4.1.2272.1.13.5.1.13

Counter32

read-only

The number of Config BPUDs received by this port.

C32 rcStgPortInTcnBpdus

1.3.6.1.4.1.2272.1.13.5.1.14

Counter32

read-only

The number of Topology Change Notification BPUDs received by this port.

C32 rcStgPortInBadBpdus

1.3.6.1.4.1.2272.1.13.5.1.15

Counter32

read-only

The number of Bad BPUDs received by this port.

C32 rcStgPortOutConfigBpdus

1.3.6.1.4.1.2272.1.13.5.1.16

Counter32

read-only

The number of Config BPUDs transmitted by this port.

C32 rcStgPortOutTcnBpdus

1.3.6.1.4.1.2272.1.13.5.1.17

Counter32

read-only

The number of Topology Change Notification BPUDs transmitted by this port.

ROW rcStgPortRowStatus

1.3.6.1.4.1.2272.1.13.5.1.18

RowStatus

read-write

Row status.

T/F rcStgPortChangeDetection

1.3.6.1.4.1.2272.1.13.5.1.19

TruthValue

read-write

If disabled, topology change notifications are not sent for the port.

I32 rcStgPortPathCost32

1.3.6.1.4.1.2272.1.13.5.1.20

Integer32

read-write

The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1998 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN. Replacement for deprecated object dot1dStpPortPathCost.

rcBridge

1.3.6.1.4.1.2272.1.14

I32 rcBridgeFdbTblSize

1.3.6.1.4.1.2272.1.14.2

Integer32

read-only

Used to indicate the number of entries in the bridge forwarding database table.

rcBridgeStaticTable

1.3.6.1.4.1.2272.1.14.3

not-accessible

This table is a proprietary replacement to the standard dot1dStaticTable in rfc1493.

rcBridgeStaticEntry

1.3.6.1.4.1.2272.1.14.3.1

not-accessible

A table containing forwarding information about unicast entries configured into the bridge by management. This information is used by the transparent bridging function in determining how to propagate a received frame.

MAC rcBridgeStaticAddress

1.3.6.1.4.1.2272.1.14.3.1.1

MacAddress

read-only

The MAC address of this entry.

NUM rcBridgeStaticPort

1.3.6.1.4.1.2272.1.14.3.1.2

InterfaceIndex

read-only

Port on which the MAC address is found.

INT rcBridgeStaticStatus

1.3.6.1.4.1.2272.1.14.3.1.5

INTEGER

read-write

This object indicates the status of this entry. The default value is permanent(3).

RCV rcBridgeStaticVlanId

1.3.6.1.4.1.2272.1.14.3.1.7

RcVlanIdOrNone

read-only

I32 rcBridgeStaticTblSize

1.3.6.1.4.1.2272.1.14.4

Integer32

read-only

Used to indicate the number of entries in the bridge static table.

rcBridgeUnknownMacDiscardTable

1.3.6.1.4.1.2272.1.14.7

not-accessible

This table is used to configure the 'unknown mac discard' feature. This feature applies to layer 2 and layer 3 packets coming from or going out to a specific physical port.

rcBridgeUnknownMacDiscardEntry

1.3.6.1.4.1.2272.1.14.7.1

not-accessible

A table containing information configuring the 'unknown mac discard' feature.

NUM rcBridgeUnknownMacDiscardIfIndex

1.3.6.1.4.1.2272.1.14.7.1.1

InterfaceIndex

read-only

Port on which this 'unknown mac discard' configuration applied to.

T/F rcBridgeUnknownMacDiscardAutoLearnEnable

1.3.6.1.4.1.2272.1.14.7.1.2

TruthValue

read-write

This variable is used to enable/disable the auto-learn capability of a specific port. The default value is auto-learn disabled.

INT rcBridgeUnknownMacDiscardAutoLearnMode

1.3.6.1.4.1.2272.1.14.7.1.3

INTEGER

read-write

This variable is used to control the auto-learn mode to either one-shot or continuous. In one-shot mode, the first n MAC addresses will be learned. The number n is dependents on the system's available resource. In continuous mode, MAC address is continuous learned until the resource limit is reached. After that the subsequent MAC will be disallowed until one of the original learned MAC is aged out. The default value is one-shot mode.

INT rcBridgeUnknownMacDiscardAutoLearnTableMode

1.3.6.1.4.1.2272.1.14.7.1.4

INTEGER

read-write

This MIB variable is used to lock or unlock the auto-learn MAC table. When the auto-learn table is lock neither new MAC will be learned nor the original learned MAC will be aged out. User needs to lock the auto-learn table before MAC addresses can be save to the NVRAM. The whole auto-learn table will be flushed when the setting change from lock to unlock mode. The default value is unlock mode.

INT rcBridgeUnknownMacDiscardLogViolations

1.3.6.1.4.1.2272.1.14.7.1.5

INTEGER

read-write

This variable controls the logging action that the system will take when a MAC address violation event was detected. The value 'enable' means a log record will be written to the system log file when a violation event was detected. The default value is enable.

INT rcBridgeUnknownMacDiscardSendTrap

1.3.6.1.4.1.2272.1.14.7.1.6

INTEGER

read-write

This variable controls the send trap action that system will take when a MAC address violation event was detected. The value 'enable' means a SNMP trap packet will be send to the management station when a violation event was detected. The default value is disable.

INT rcBridgeUnknownMacDiscardDisablePort

1.3.6.1.4.1.2272.1.14.7.1.7

INTEGER

read-write

This variable controls the 'disable-port' action that system will take when a MAC address violation event was detected. The value 'enable' means the specific port will be disabled when the violation event was detected. It needs user manually to bring the port back once it was disabled. The default value is disable.

INT rcBridgeUnknownMacDiscardMacCountMax

1.3.6.1.4.1.2272.1.14.7.1.10

INTEGER

read-write

This variable represents the maxium number of MACc that can be added to some port.

INT rcBridgeUnknownMacDiscardMacCountCur

1.3.6.1.4.1.2272.1.14.7.1.11

INTEGER

read-only

This variable represents the current number of MACs that have been added to some port.

rcBridgeManualEditTable

1.3.6.1.4.1.2272.1.14.8

not-accessible

This table is used to specify what MAC addresses can be learned on each port.

rcBridgeManualEditEntry

1.3.6.1.4.1.2272.1.14.8.1

not-accessible

A table containing information of MAC addresses that can be learned.

MAC rcBridgeManualEditAddress

1.3.6.1.4.1.2272.1.14.8.1.1

MacAddress

read-only

This variable contains the source MAC address of an entry.

POR rcBridgeManualEditPorts

1.3.6.1.4.1.2272.1.14.8.1.2

PortSet

read-write

This variable contains the allowed ports on which the MAC address of this entry can be learned.

T/F rcBridgeManualEditMonitor

1.3.6.1.4.1.2272.1.14.8.1.3

TruthValue

read-write

This variable specifies the monitoring setting of the MAC address. The value 'true' means a copy of packet frame that send from or to the MAC address is forwarded to the designated monitoring port on the system. The default value is false.

INT rcBridgeManualEditPriority

1.3.6.1.4.1.2272.1.14.8.1.4

INTEGER

read-write

This variable specifies the priority setting of the MAC address. The value 'low' means packet frames send from the MAC address is forwarded at low priority. The default value is low.

INT rcBridgeManualEditStatus

1.3.6.1.4.1.2272.1.14.8.1.5

INTEGER

read-write

The variable controls the status of a MAC address in the table. The value 'active' is used to add the MAC address entry into the table. The value 'invalid' is used to delete the MAC address from the table.

I32 rcBridgeManualEditTblSize

1.3.6.1.4.1.2272.1.14.9

Integer32

read-only

Used to indicate the number of entries in the manual edit table.

rcBridgeAutoLearnTable

1.3.6.1.4.1.2272.1.14.10

not-accessible

This table contains information of auto-learned MAC address when the 'unknow MAC discard' table's auto-learn is enabled. User must explicitly lock and save the table into NVRAM in order to have this table has the same configuration cross the system reset.

rcBridgeAutoLearnEntry

1.3.6.1.4.1.2272.1.14.10.1

not-accessible

Entries in this table are created automatically when the user explicitly does a lock operation on the auto-learn-table (i.e., when 'AutoLearnTableMode' is set to lock(2)).

MAC rcBridgeAutoLearnAddress

1.3.6.1.4.1.2272.1.14.10.1.1

MacAddress

read-only

This variable contains the source MAC address of the entries.

POR rcBridgeAutoLearnPort

1.3.6.1.4.1.2272.1.14.10.1.2

PortSet

read-only

This variable contains the port where the MAC address was learned.

T/F rcBridgeAutoLearnMonitor

1.3.6.1.4.1.2272.1.14.10.1.3

TruthValue

read-only

This variable contains the monitor setting of the MAC address. The value 'true' means a copy of packet frame that send from or to the MAC address is forwarded to the designated monitoring port on the system. This value should be synchronized with the setting of 'unknow MAC discard' table's 'Default AutoLearnMonitor' setting when the MAC address was learned.

INT rcBridgeAutoLearnPriority

1.3.6.1.4.1.2272.1.14.10.1.4

INTEGER

read-only

This variable contains the priority setting of the MAC address. The value 'low' means packet frames send from the MAC address is forwarded at low priority. The value 'high' means packet frames send from the MAC address is forwarded at high priority. This value should be synchronized with the setting of 'unknow MAC discard' table's 'DefaultAutoLearnPriority' setting when the MAC address was learned.

INT rcBridgeAutoLearnAction

1.3.6.1.4.1.2272.1.14.10.1.5

INTEGER

read-write

This variable is for converting an auto-learned MAC address entry to a manual edit MAC address entry. This variable provides a mechanism for user to move a MAC address entry from auto-learn table to manual edit table.

I32 rcBridgeAutoLearnTblSize

1.3.6.1.4.1.2272.1.14.11

Integer32

read-only

Used to indicate the number of entries in the auto learn table.

I32 rcBridgeStaticMulticastTblSize

1.3.6.1.4.1.2272.1.14.13

Integer32

read-only

Used to indicate the number of entries in the static multicast table.

rcRateLimitTable

1.3.6.1.4.1.2272.1.14.14

not-accessible

rcRateLimitEntry

1.3.6.1.4.1.2272.1.14.14.1

not-accessible

NUM rcRateLimitIfIndex

1.3.6.1.4.1.2272.1.14.14.1.1

InterfaceIndex

read-only

Port ifindex.

INT rcRateLimitIfTrafficType

1.3.6.1.4.1.2272.1.14.14.1.2

INTEGER

read-write

Type of traffic allowed.

T/F rcRateLimitIfEnable

1.3.6.1.4.1.2272.1.14.14.1.4

TruthValue

read-write

Turn on/off rate limiting on this interface.

I32 rcRateLimitIfAllowedRatePps

1.3.6.1.4.1.2272.1.14.14.1.5

Integer32

read-write

Allowed traffic rate packets per second. 0 means disabled

rcBridgeStaticMcastTable

1.3.6.1.4.1.2272.1.14.15

not-accessible

rcBridgeStaticMcastEntry

1.3.6.1.4.1.2272.1.14.15.1

not-accessible

INT rcBridgeStaticMcastVlanId

1.3.6.1.4.1.2272.1.14.15.1.1

INTEGER

read-only

Vlan Id

MAC rcBridgeStaticMcastAddress

1.3.6.1.4.1.2272.1.14.15.1.2

MacAddress

read-only

src mac addr.

POR rcBridgeStaticMcastForwardingPorts

1.3.6.1.4.1.2272.1.14.15.1.3

PortSet

read-write

ports for forward this mac

IDL rcBridgeStaticMcastMltIds

1.3.6.1.4.1.2272.1.14.15.1.4

IdList

read-write

list of mlts this mac will be forwarded on

I32 rcBridgeStaticMcastNumMltIds

1.3.6.1.4.1.2272.1.14.15.1.5

Integer32

read-only

number of mlts Ids

ROW rcBridgeStaticMcastRowStatus

1.3.6.1.4.1.2272.1.14.15.1.6

RowStatus

read-write

row status

rcBridgeFdbProtectTable

1.3.6.1.4.1.2272.1.14.17

not-accessible

This table gives information about the mac learning limits on a particular port.

rcBridgeFdbProtectEntry

1.3.6.1.4.1.2272.1.14.17.1

not-accessible

Information about a specific MAC address learning limits of a specific port.

NUM rcBridgeFdbProtectPortNum

1.3.6.1.4.1.2272.1.14.17.1.1

InterfaceIndex

read-only

This object is the interface on which MAC address learning limit is applied.

I32 rcBridgeFdbProtectMaxMacCount

1.3.6.1.4.1.2272.1.14.17.1.2

Integer32

read-write

Used to indicate maximum number of MAC address that can be learnt on the port.

I32 rcBridgeFdbProtectMinMacCount

1.3.6.1.4.1.2272.1.14.17.1.3

Integer32

read-write

Used to indicate minimum number of MAC address learnt which mac address learning will be re-enabled on the port.

ENA rcBridgeFdbProtectEnable

1.3.6.1.4.1.2272.1.14.17.1.4

EnableValue

read-write

Used to enable or disable MAC learning limit feature on the port.

I32 rcBridgeFdbProtectCurrentMacCount

1.3.6.1.4.1.2272.1.14.17.1.5

Integer32

read-only

This object indicates the current number of MAC address learnt on the port.

T/F rcBridgeFdbProtectMacLearning

1.3.6.1.4.1.2272.1.14.17.1.6

TruthValue

read-only

This object indicates whether the port can currrently learn new MAC addresses or not.

ENA rcBridgeFdbProtectViolationLogTrap

1.3.6.1.4.1.2272.1.14.17.1.7

EnableValue

read-write

Used to enable or disable logging and sending of snmp trap, once MAC learning limit is reached for the port.

ENA rcBridgeFdbProtectViolationDownPort

1.3.6.1.4.1.2272.1.14.17.1.8

EnableValue

read-write

Used to enable or disable the action of disabling the port, once MAC learning limit is reached for the port.

rcBridgeTpFdbTable

1.3.6.1.4.1.2272.1.14.20

not-accessible

This table is an replacement to the standard dot1dTpFdbTable in rfc1493.

rcBridgeTpFdbEntry

1.3.6.1.4.1.2272.1.14.20.1

not-accessible

Information about a specific unicast MAC address for which the bridge has some forwarding information.

RCV rcBridgeTpFdbVlanId

1.3.6.1.4.1.2272.1.14.20.1.1

RcVlanIdOrNone

not-accessible

Used to indicate the Vlan ID for this MAC address.

MAC rcBridgeTpFdbAddress

1.3.6.1.4.1.2272.1.14.20.1.2

MacAddress

not-accessible

A unicast MAC address for which the bridge has forwarding and/or filtering information.

INT rcBridgeTpFdbStatus

1.3.6.1.4.1.2272.1.14.20.1.3

INTEGER

read-write

This object indicates the status of this entry.

NUM rcBridgeTpFdbPort

1.3.6.1.4.1.2272.1.14.20.1.4

InterfaceIndex

read-only

Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of rcBridgeTpFdbAddress has been seen. A value of '0' indicates that the port number has not been learned but that the bridge does have some forwarding/filtering information about this address (e.g. in the dot1dStaticTable). Implementors are encouraged to assign the port value to this object whenever it is learned even for addresses for which the corresponding value of rcBridgeTpFdbStatus is not learned(3).

T/F rcBridgeTpFdbSmltRemote

1.3.6.1.4.1.2272.1.14.20.1.5

TruthValue

read-only

A MAC address indicate for remote learnt, either local or remote.

MAC rcBridgeTpFdbBMac

1.3.6.1.4.1.2272.1.14.20.1.6

MacAddress

read-only

If the rcBridgeTpFdbEntry is learned from a SPBM network, instead of using port to track where the rcBridgeTpFdbAddress come from, the backbone MAC address is used to track that.

rcBridgeRemoteMacTable

1.3.6.1.4.1.2272.1.14.21

not-accessible

This table is for PLSB cvlan UNI remote mac entries

rcBridgeRemoteMacEntry

1.3.6.1.4.1.2272.1.14.21.1

not-accessible

Information about a specific cvlan UNI remote MAC address for which the bridge has the forwarding information.

I32 rcBridgeRemoteMacVlanId

1.3.6.1.4.1.2272.1.14.21.1.1

Integer32

not-accessible

Used to indicate the Vlan ID for this MAC address.

MAC rcBridgeRemoteMacAddr

1.3.6.1.4.1.2272.1.14.21.1.2

MacAddress

not-accessible

A customer MAC address for which the bridge has forwarding and/or filtering information.

INT rcBridgeRemoteMacStatus

1.3.6.1.4.1.2272.1.14.21.1.3

INTEGER

read-only

This object indicates the status of this entry.

MAC rcBridgeRemoteMacDestAddr

1.3.6.1.4.1.2272.1.14.21.1.4

MacAddress

read-only

A provider MAC address for which the bridge has forwarding and/or filtering information.

I32 rcBridgeRemoteMacPrimaryBVlanId

1.3.6.1.4.1.2272.1.14.21.1.5

Integer32

read-only

Used to indicate the BVlan ID for this MAC address.

OCT rcBridgeRemoteMacPrimaryDestSysName

1.3.6.1.4.1.2272.1.14.21.1.6

OCTET STRING

read-only

Primary System name of the node where MAC address entry come from.

NUM rcBridgeRemoteMacPrimaryPort

1.3.6.1.4.1.2272.1.14.21.1.7

InterfaceIndex

read-only

Either the value '0', or the primary port on which a frame came from.

I32 rcBridgeRemoteMacSecondaryBVlanId

1.3.6.1.4.1.2272.1.14.21.1.8

Integer32

read-only

Used to indicate the BVlan ID for this MAC address.

OCT rcBridgeRemoteMacSecondaryDestSysName

1.3.6.1.4.1.2272.1.14.21.1.9

OCTET STRING

read-only

Secondary System name of the node where MAC address entry come from.

NUM rcBridgeRemoteMacSecondaryPort

1.3.6.1.4.1.2272.1.14.21.1.10

InterfaceIndex

read-only

Either the value '0', or the secondary port on which a frame came from.

T/F rcBridgeRemoteMacSmltRemote

1.3.6.1.4.1.2272.1.14.21.1.11

TruthValue

read-only

A MAC address indicate for remote learnt from ist peer

rcBoot

1.3.6.1.4.1.2272.1.15

rcDevice

1.3.6.1.4.1.2272.1.16

rcMlt

1.3.6.1.4.1.2272.1.17

I32 rcMltNumMlts

1.3.6.1.4.1.2272.1.17.1

Integer32

read-only

The number of MLTs currently defined in the switch.

POR rcMltPotentialMembers

1.3.6.1.4.1.2272.1.17.2

PortSet

read-only

The set of ports that are not members of any MLT.

ENA rcMltIstSessionEnable

1.3.6.1.4.1.2272.1.17.3

EnableValue

read-write

Used to enable/disable mlt functionality.

INT rcMltIstSessionStatus

1.3.6.1.4.1.2272.1.17.4

INTEGER

read-only

Used to enable/disable mlt functionality.

IP rcMltIstPeerIp

1.3.6.1.4.1.2272.1.17.5

IpAddress

read-write

IST mlt Peer Ip address.

INT rcMltIstVlanId

1.3.6.1.4.1.2272.1.17.6

INTEGER

read-write

IST mlt Vlan Id. 0 is default when it is not set, VSP supports 0 to 4084

rcMltTable

1.3.6.1.4.1.2272.1.17.10

not-accessible

A list of Multi-Link Trunk entries. The number of entries is given by rcMltNumMlts.

rcMltEntry

1.3.6.1.4.1.2272.1.17.10.1

not-accessible

Entry containing configuration information for a particular Multi-Link Trunk.

INT rcMltId

1.3.6.1.4.1.2272.1.17.10.1.1

INTEGER

read-only

A value that uniquely identifies the Multi-Link Trunk associated with this entry.

STR rcMltName

1.3.6.1.4.1.2272.1.17.10.1.2

DisplayString

read-write

An administratively-assigned name for this MLT.

POR rcMltPortMembers

1.3.6.1.4.1.2272.1.17.10.1.3

PortSet

read-write

The set of ports that are members of this MLT.

INT rcMltPortType

1.3.6.1.4.1.2272.1.17.10.1.4

INTEGER

read-write

The type of MLT port: access(1) or trunk(2).

I32 rcMltNumVlanIds

1.3.6.1.4.1.2272.1.17.10.1.5

Integer32

read-only

Used to indicate the number of VLAN IDs that are stored in the rcMltVlanIds variable.

ROW rcMltRowStatus

1.3.6.1.4.1.2272.1.17.10.1.7

RowStatus

read-write

Used to create/delete entries in the rcMltTable.

T/F rcMltEnable

1.3.6.1.4.1.2272.1.17.10.1.8

TruthValue

read-only

Enable the entry.

T/F rcMltLoadBalance

1.3.6.1.4.1.2272.1.17.10.1.9

TruthValue

read-write

Perform load balance?

NUM rcMltIfIndex

1.3.6.1.4.1.2272.1.17.10.1.11

InterfaceIndex

read-only

Used to indicate the 'logical' ifIndex assigned to this MLT.

INT rcMltMltType

1.3.6.1.4.1.2272.1.17.10.1.12

INTEGER

read-write

MLT type.

INT rcMltRunningType

1.3.6.1.4.1.2272.1.17.10.1.14

INTEGER

read-only

Split MLT running type.

ENA rcMltMulticastDistribution

1.3.6.1.4.1.2272.1.17.10.1.16

EnableValue

read-write

Enable/Disable multicast distribution per mlt.

ENA rcMltAggregatable

1.3.6.1.4.1.2272.1.17.10.1.18

EnableValue

read-write

Enable/Disable link aggregation on a MLT.

INT rcMltClearLinkAggregate

1.3.6.1.4.1.2272.1.17.10.1.19

INTEGER

read-write

clear link aggregate, equivalent to disable and re-enable aggregatable on the MLT.

NUM rcMltDesignatedPort

1.3.6.1.4.1.2272.1.17.10.1.21

InterfaceIndex

read-only

Indicates the Designated port for the MLT.

ENA rcMltAggOperState

1.3.6.1.4.1.2272.1.17.10.1.22

EnableValue

read-only

Link aggregation state on a MLT.

TIK rcMltAggTimeOfLastOperChange

1.3.6.1.4.1.2272.1.17.10.1.23

TimeTicks

read-only

The time value since the interface entered its current operational state.

POR rcMltPeerPortMembers

1.3.6.1.4.1.2272.1.17.10.1.39

PortSet

read-only

The set of Peer ports which are connected to local ports (rcMltPortMember) of this MLT

INT rcMltCpLimitPktRate

1.3.6.1.4.1.2272.1.17.10.1.40

INTEGER

read-write

Used to limit Control packets on the port to qos-levels 6 and 7. Sets the limit in packets per second.

T/F rcMltCpLimitShutDownEnable

1.3.6.1.4.1.2272.1.17.10.1.41

TruthValue

read-write

Used to indicate if the mlt-ports should be shutdown when the CpLimitPktRate is exceeded.

OCT rcMltVlanIdList

1.3.6.1.4.1.2272.1.17.10.1.42

OCTET STRING

read-write

This bitfield is used to identify which VLANs this MLT is associated with. Each VLAN ID is stored as a bit. The most-significant (left-most) bit represents Vlan Id 1.

INT rcMltEntryOwner

1.3.6.1.4.1.2272.1.17.10.1.43

INTEGER

read-only

Defines the owner of the MLT.

INT rcMltDatapathProgrammingState

1.3.6.1.4.1.2272.1.17.10.1.44

INTEGER

read-only

Defines the datapath programming state of the MLT.

rcMltMcastDistribution

1.3.6.1.4.1.2272.1.17.11

T/F rcMltMcastDistributionEnable

1.3.6.1.4.1.2272.1.17.11.1

TruthValue

read-write

Used to enable/disable this feature to distribute multicast traffic on MLT ports. All the cards in the system must be E-Tickets. Cannot perform distribution in a mixed mode.

IP rcMltMcastDistributionGrpMask

1.3.6.1.4.1.2272.1.17.11.2

IpAddress

read-write

Group Mask. Create a MLT abstraction layer to distribute traffic basd on (source, group) information of the multicast packet. The algorithm to pick the actual port nedds to generate a fairly random number for different combinations but a lways generate the same number for a given (source, group) pair. By default, the number of active ports of the MLT is used to MOD the pseudo-random number generated by the XOR of each byte of the masked group address with the masked source address.

IP rcMltMcastDistributionSrcMask

1.3.6.1.4.1.2272.1.17.11.3

IpAddress

read-write

Source Mask.

T/F rcMltMcastDistributionRedistributionEnable

1.3.6.1.4.1.2272.1.17.11.4

TruthValue

read-write

Enable redistribution.

rcWeb

1.3.6.1.4.1.2272.1.18

T/F rcWebEnableServer

1.3.6.1.4.1.2272.1.18.1

TruthValue

read-write

Control whether the web server should be enabled. Setting this variable to true will make the server operational. Setting this variable to false will disable server.

STR rcWebRWAUserName

1.3.6.1.4.1.2272.1.18.2

DisplayString

read-write

User name for the read-write-all web-server account.

STR rcWebRWAPassword

1.3.6.1.4.1.2272.1.18.3

DisplayString

read-write

Password for the read-write-all web-server account.

STR rcWebRWUserName

1.3.6.1.4.1.2272.1.18.4

DisplayString

read-write

User name for the read-write web-server account.

STR rcWebRWPassword

1.3.6.1.4.1.2272.1.18.5

DisplayString

read-write

Password for the read-write web-server account.

STR rcWebROUserName

1.3.6.1.4.1.2272.1.18.6

DisplayString

read-write

User name for the read-only web-server account.

STR rcWebROPassword

1.3.6.1.4.1.2272.1.18.7

DisplayString

read-write

Password for the read-only web-server account.

TIK rcWebLastChange

1.3.6.1.4.1.2272.1.18.8

TimeTicks

read-only

Last web-browser initiated configuration change since sysUpTime.

I32 rcWebNumHits

1.3.6.1.4.1.2272.1.18.9

Integer32

read-only

Number of hits to the web-server

I32 rcWebNumAccessChecks

1.3.6.1.4.1.2272.1.18.10

Integer32

read-only

Number of access checks performed by the web-server

I32 rcWebNumAccessBlocks

1.3.6.1.4.1.2272.1.18.11

Integer32

read-only

Number of accesses blocked by the web-server

I32 rcWebNumRxErrors

1.3.6.1.4.1.2272.1.18.12

Integer32

read-only

Number of receive errors encountered by the web-server

I32 rcWebNumTxErrors

1.3.6.1.4.1.2272.1.18.13

Integer32

read-only

Number of transmit errors encountered by the web-server

I32 rcWebNumSetRequest

1.3.6.1.4.1.2272.1.18.14

Integer32

read-only

Number of set-request to the web-server

STR rcWebPrimaryHtmlSourceDir

1.3.6.1.4.1.2272.1.18.15

DisplayString

read-write

primary html source directory

STR rcWebSecondaryHtmlSourceDir

1.3.6.1.4.1.2272.1.18.16

DisplayString

read-write

secondary html source directory

STR rcWebTertiaryHtmlSourceDir

1.3.6.1.4.1.2272.1.18.17

DisplayString

read-write

tertiary html source directory

STR rcWebRWL3UserName

1.3.6.1.4.1.2272.1.18.18

DisplayString

read-write

user name for the L3 web server account

STR rcWebRWL3Password

1.3.6.1.4.1.2272.1.18.19

DisplayString

read-write

password for the L3 web server account

STR rcWebRWL2UserName

1.3.6.1.4.1.2272.1.18.20

DisplayString

read-write

user name for the L2 web server account

STR rcWebRWL2Password

1.3.6.1.4.1.2272.1.18.21

DisplayString

read-write

password for the L2 web server account

INT rcWebDefaultDisplayRows

1.3.6.1.4.1.2272.1.18.22

INTEGER

read-write

default display rows in html page.

IP rcWebLastHostAccessBlocked

1.3.6.1.4.1.2272.1.18.23

IpAddress

read-only

last host access blocked

OCT rcWebHelpTftpSourceDir

1.3.6.1.4.1.2272.1.18.24

OCTET STRING

read-write

tftp source directory for help files

INT rcWebHttpPort

1.3.6.1.4.1.2272.1.18.25

INTEGER

read-write

the HTTP port for web access

T/F rcWebSecureOnly

1.3.6.1.4.1.2272.1.18.26

TruthValue

read-write

Control whether the secure only should be enabled. Setting this variable to true will make the server support HTTPS only. Setting this variable to false will make the server support both HTTP & HTTPS

I32 rcWebHttpsPort

1.3.6.1.4.1.2272.1.18.27

Integer32

read-write

the HTTPs port for web access

rcCli

1.3.6.1.4.1.2272.1.19

STR rcCliRWAUserName

1.3.6.1.4.1.2272.1.19.1

DisplayString

read-write

User name for the read-write-all CLI account.

STR rcCliRWAPassword

1.3.6.1.4.1.2272.1.19.2

DisplayString

read-write

Password for the read-write-all CLI account.

STR rcCliRWUserName

1.3.6.1.4.1.2272.1.19.3

DisplayString

read-write

User name for the read-write CLI account.

STR rcCliRWPassword

1.3.6.1.4.1.2272.1.19.4

DisplayString

read-write

Password for the read-write CLI account.

STR rcCliRWL3UserName

1.3.6.1.4.1.2272.1.19.5

DisplayString

read-write

User name for the read-write layer-3 CLI account.

STR rcCliRWL3Password

1.3.6.1.4.1.2272.1.19.6

DisplayString

read-write

Password for the read-write layer-3 CLI account.

STR rcCliRWL2UserName

1.3.6.1.4.1.2272.1.19.7

DisplayString

read-write

User name for the read-write layer-2 CLI account.

STR rcCliRWL2Password

1.3.6.1.4.1.2272.1.19.8

DisplayString

read-write

Password for the read-write layer-2 CLI account.

STR rcCliROUserName

1.3.6.1.4.1.2272.1.19.9

DisplayString

read-write

User name for the read-only CLI account.

STR rcCliROPassword

1.3.6.1.4.1.2272.1.19.10

DisplayString

read-write

Password for the read-only CLI account.

INT rcCliMaxTelnetSessions

1.3.6.1.4.1.2272.1.19.11

INTEGER

read-write

Used to indicate the maximum number of telnet sessions the system will support.

INT rcCliMaxRloginSessions

1.3.6.1.4.1.2272.1.19.12

INTEGER

read-write

Used to indicate the maximum number of rlogin sessions the system will support.

INT rcCliTimeout

1.3.6.1.4.1.2272.1.19.13

INTEGER

read-write

Used to indicate the amount of idle time, in seconds to wait before timing out telnet and rlogin sessions.

I32 rcCliNumAccessViolations

1.3.6.1.4.1.2272.1.19.14

Integer32

read-only

Used to indicate the number of CLI access violations detected by the system.

STR rcCliRWL1UserName

1.3.6.1.4.1.2272.1.19.15

DisplayString

read-write

User name for the read-write layer-1 CLI account.

STR rcCliRWL1Password

1.3.6.1.4.1.2272.1.19.16

DisplayString

read-write

Password for the read-write layer-1 CLI account.

INT rcCliPasswordChange

1.3.6.1.4.1.2272.1.19.17

INTEGER

read-only

Used to indication which password is changed when sending a rcCliPasswordChange trap.

INT rcCliPassChangeResult

1.3.6.1.4.1.2272.1.19.18

INTEGER

read-only

Used to indication the result of changing password when sending a rcPasswordChange trap.

T/F rcCliRWEnable

1.3.6.1.4.1.2272.1.19.19

TruthValue

read-write

Enable/Disable for the read-write CLI account.

T/F rcCliRWL1Enable

1.3.6.1.4.1.2272.1.19.20

TruthValue

read-write

Enable/Disable for the read-write-layer1 CLI account.

T/F rcCliRWL2Enable

1.3.6.1.4.1.2272.1.19.21

TruthValue

read-write

Enable/Disable for the read-write-layer2 CLI account.

T/F rcCliRWL3Enable

1.3.6.1.4.1.2272.1.19.22

TruthValue

read-write

Enable/Disable for the read-write-layer3 CLI account.

T/F rcCliROEnable

1.3.6.1.4.1.2272.1.19.23

TruthValue

read-write

Enable/Disable for the read-only CLI account.

rcError

1.3.6.1.4.1.2272.1.20

I32 rcErrorLevel

1.3.6.1.4.1.2272.1.20.1

Integer32

read-only

Error level indicator for the last error reported in the system. The meaning of this value are : 0 = Informative Information 1 = Warning Condition 2 = Error Condition 3 = Manufacturing Information 4 = Fatal Condition

I32 rcErrorCode

1.3.6.1.4.1.2272.1.20.2

Integer32

read-only

Error code indicator for the last error reported in the system. This is an encoded value that identifies the software module that generated the error message as well as a specific error condition within that module. This value is transparent to the user. This value is intended to help Accelar support and development staff to isolate system problems.

STR rcErrorText

1.3.6.1.4.1.2272.1.20.3

DisplayString

read-only

Error string of the last error reported in the system.

INT rcErrorReturnCode

1.3.6.1.4.1.2272.1.20.4

INTEGER

read-only

This variable is used primarily as an enumeration to list the proprietary return codes that this device can send to a management station in response to a failed SNMP operation.

T/F rcErrorSendTrap

1.3.6.1.4.1.2272.1.20.5

TruthValue

read-write

Indicates whether to send trap upon receiving an error in the system.

rcTraps

1.3.6.1.4.1.2272.1.21

rcTrapsMib

1.3.6.1.4.1.2272.1.21.0

NTF rcnCardDown

1.3.6.1.4.1.2272.1.21.0.1

A rcnCardDown trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcCardOperStatus object for one of its cards is about to transition into the down state.

NTF rcnCardUp

1.3.6.1.4.1.2272.1.21.0.2

A rcnCardUp trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcCardOperStatus object for one of its cards is about to transition into the up state.

NTF rcnErrorNotification

1.3.6.1.4.1.2272.1.21.0.3

A rcnErrorNotification trap signifies that the SNMPv2 entity, acting in an agent role, has detected that an error condition has occured.

NTF rcnStpNewRoot

1.3.6.1.4.1.2272.1.21.0.4

A rcnStpNewRoot trap signifies that the SNMPv2 entity, acting in an agent role, has detected the Spanning Tree Protocol has declared the device to be the new root of the spanning tree.

NTF rcnStpTopologyChange

1.3.6.1.4.1.2272.1.21.0.5

A rcnStpTopologyChange trap signifies that the SNMPv2 entity, acting in an agent role, has detected the Spanning Tree Protocol has gone due a topology change event.

NTF rcnChasPowerSupplyDown

1.3.6.1.4.1.2272.1.21.0.6

A rcnChasPowerSupplyDown trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcChasPowerSupplyOperStatus object for one of its power supply unit is about to transition into the down state.

NTF rcnChasFanDown

1.3.6.1.4.1.2272.1.21.0.7

A rcnChasFanDown trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcChasFanOperStatus object for one of its power supply unit is about to transition into the down state.

NTF rcnLinkOscillation

1.3.6.1.4.1.2272.1.21.0.8

A rcnLinkOscillation trap signifies that the SNMPv2 entity, acting in an agent role, has detected an excessive number of link state transitions on the specified port.

NTF rcnMacViolation

1.3.6.1.4.1.2272.1.21.0.9

A rcnMacViolation trap signifies that the SNMPv2 entity, acting in an agent role, has received a PDU with an invalid source MAC address.

NTF rcnSonetTrap

1.3.6.1.4.1.2272.1.21.0.10

A rcnSonetTrap trap signifies that the SNMPv2 entity, acting in an agent role, has detected a change of status on a Sonet port.

NTF rcn2kCardDown

1.3.6.1.4.1.2272.1.21.0.11

A rcnCardDown trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcCardOperStatus object for one of its cards is about to transition into the down state.

NTF rcn2kCardUp

1.3.6.1.4.1.2272.1.21.0.12

A rcnCardUp trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcCardOperStatus object for one of its cards is about to transition into the up state.

NTF rcn2kTemperature

1.3.6.1.4.1.2272.1.21.0.13

A rcn2kTemperature trap signifies that the SNMPv2 entity, acting in an agent role, has detected the chassis is over-heating.

NTF rcnChasPowerSupplyUp

1.3.6.1.4.1.2272.1.21.0.14

A rcnChasPowerSupplyUp trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcChasPowerSupplyOperStatus object for one of its power supply unit is about to transition into the up state.

NTF rcn2kAtmPvcLinkStateChange

1.3.6.1.4.1.2272.1.21.0.15

A rcn2kAtmPvcLinkStateChange trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rc2kAtmPvcOamVcStatus object for one of PVC is about to transition into different state, either from up to down or from down to up.

NTF rcnStpTCN

1.3.6.1.4.1.2272.1.21.0.16

A rcnStpTopologyChange trap signifies that the SNMPv2 entity, acting in an agent role, has detected the Spanning Tree Protocol has gone due a topology change event.

NTF rcnSmltIstLinkUp

1.3.6.1.4.1.2272.1.21.0.17

A rcnSmltIstLinkUp trap signifies that the split MLT link is from down to up.

NTF rcnSmltIstLinkDown

1.3.6.1.4.1.2272.1.21.0.18

A rcnSmltIstLinkDown trap signifies that the split MLT link is from up to down.

NTF rcnSmltLinkUp

1.3.6.1.4.1.2272.1.21.0.19

A rcnMltSmltId trap signifies that the split SMLT link is up.

NTF rcnSmltLinkDown

1.3.6.1.4.1.2272.1.21.0.20

A rcMltSmltId trap signifies that the split SMLT link is down.

NTF rcnChasFanUp

1.3.6.1.4.1.2272.1.21.0.21

A rcnChasFanUp trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the rcChasFanOperStatus object for one of its power supply unit is about to transition into the up state.

NTF rcnPasswordChange

1.3.6.1.4.1.2272.1.21.0.22

A rcnPasswordChange trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the one of the cli password is changed.

NTF rcnEmError

1.3.6.1.4.1.2272.1.21.0.23

A rcnEmError trap signifies that the SNMPv2 entity, acting in an agent role, has detected Em error.

NTF rcnPcmciaCardRemoved

1.3.6.1.4.1.2272.1.21.0.25

A rcnPcmciaRemoved trap signifies that the SNMPv2 entity, acting in an agent role, has detected that the PCMCIA card is being removed.

NTF rcnSmartCpldTimerFired

1.3.6.1.4.1.2272.1.21.0.26

A rcnSmartCpldTimerFired trap signifies that the cpld timer fired.

NTF rcnCardCpldNotUpDate

1.3.6.1.4.1.2272.1.21.0.27

A rcnCardCpldNotUpDate trap signifies that the cpld is not up to date.

NTF rcnIgapLogFileFull

1.3.6.1.4.1.2272.1.21.0.28

A rcnIgapLogFileFull trap signifies that the Igap accounting time-out Log File reach the maximum.

NTF rcnCpLimitShutDown

1.3.6.1.4.1.2272.1.21.0.29

A rcnCpLimitShutDown trap signifies that the cp limit for the port is shutting down.

NTF rcnSshServerEnabled

1.3.6.1.4.1.2272.1.21.0.30

A rcnSshServerEnabled trap signifies that the SSH server is enabled.

NTF rcnSshServerDisabled

1.3.6.1.4.1.2272.1.21.0.31

A rcnSshServerDisabled trap signifies that the SSH server is disabled.

NTF rcnSshSessionLogin

1.3.6.1.4.1.2272.1.21.0.32

A rcnSshSessionLogin trap signifies that there is a SSH session login. It's deprecated by rcnaSshSessionLogin.

NTF rcnSshSessionLogout

1.3.6.1.4.1.2272.1.21.0.33

A rcnSshSessionLogout trap signifies that there is a SSH session logout. It's deprecated by rcnaSshSessionLogout.

NTF rcnSshUnauthorizedAccess

1.3.6.1.4.1.2272.1.21.0.34

A rcnSshUnauthorizedAccess trap signifies that an unauthorized access has occured. It's deprecated by rcnaSshUnauthorizedAccess.

NTF rcnHaCpuState

1.3.6.1.4.1.2272.1.21.0.35

A rcnHaCpuState trap signifies that the state of the HA-CPU.

NTF rcnInsufficientMemory

1.3.6.1.4.1.2272.1.21.0.36

A rcnInsufficientMemory trap indicates insufficient memory on CPU blade for proper operation. Recommended memory = 256 MB available through Nortel Networks upgrade kit

NTF rcnSaveConfigAction

1.3.6.1.4.1.2272.1.21.0.37

A rcnSaveConfigAction trap indicates the switch run time or boot configuration is being saved

NTF rcnLoopDetectOnPort

1.3.6.1.4.1.2272.1.21.0.38

A rcnLoopDetectOnPort trap indicates that a loop has been detected on a port. The vlan on that port will be disabled.

NTF rcnbgpEstablished

1.3.6.1.4.1.2272.1.21.0.39

The BGP Established event is generated when the BGP FSM enters the ESTABLISHED state.

NTF rcnbgpBackwardTransition

1.3.6.1.4.1.2272.1.21.0.40

The BGPBackwardTransition Event is generated when the BGP FSM moves from a higher numbered state to a lower numbered state.

NTF rcnAggLinkUp

1.3.6.1.4.1.2272.1.21.0.41

A rcnAggLinkUp trap is generated when the operational state of the aggregator changes from down to up.

NTF rcnAggLinkDown

1.3.6.1.4.1.2272.1.21.0.42

A rcnAggLinkDown trap is generated when the operational state of the aggregator changes from up to down.

NTF rcnIgmpNewGroupMember

1.3.6.1.4.1.2272.1.21.0.43

An IgmpNewGroupMember trap signifies that a new member has come on an interface.

NTF rcnIgmpLossGroupMember

1.3.6.1.4.1.2272.1.21.0.44

An IgmpLossGroupMember trap signifies that a group member has been lost on an interface.

NTF rcnIgmpNewQuerier

1.3.6.1.4.1.2272.1.21.0.45

An igmpNewQuerier trap signifies that a new querier has come up on an interface.

NTF rcnIgmpQuerierChange

1.3.6.1.4.1.2272.1.21.0.46

An rcnIgmpQuerierChange trap signifies that the querier has changed.

NTF rcnDvmrpIfStateChange

1.3.6.1.4.1.2272.1.21.0.47

A rcnDvmrpIfStateChange trap signifies that there has been a change in the state of a DVMRP interface.

NTF rcnDvmrpNewNbrChange

1.3.6.1.4.1.2272.1.21.0.48

A rcnDvmrpNewNbrChange trap signifies that a new neighbor has come up on a DVMRP interface.

NTF rcnDvmrpNbrLossChange

1.3.6.1.4.1.2272.1.21.0.49

A rcnDvmrpNbrLossChange trap signifies that a new neighbor has gone down on a DVMRP interface.

NTF rcnFdbProtectViolation

1.3.6.1.4.1.2272.1.21.0.59

The rcnFdbProtectViolation trap signifies that the has violated the user configured limit for total number of fdb-entries learned on that port.

NTF rcnLogMsgControl

1.3.6.1.4.1.2272.1.21.0.60

A rcnLogMsgControl trap signifies whether the number of times of repeatation of the particular Log message has exceeded the particular frequency/count or not.

NTF rcnSaveConfigFile

1.3.6.1.4.1.2272.1.21.0.61

A rcnSaveConfig trap signifies that either the runtime config or the boot config has been saved on the switch

NTF rcnDNSRequestResponse

1.3.6.1.4.1.2272.1.21.0.62

A rcnDnsRequestResponse trap signifies that the switch had sent a query to the DNS server or it had received a successful response from the DNS Server

NTF rcnDuplicateIpAddress

1.3.6.1.4.1.2272.1.21.0.63

A rcnDuplicateIpAddress trap signifies that a duplicate IP address is detected on the subnet.

NTF rcnLoopDetectPortDown

1.3.6.1.4.1.2272.1.21.0.64

A rcnLoopDetectPortDown trap signifies that a loop has been detected on a port and the port is going to shut down.

NTF rcnLoopDetectMacDiscard

1.3.6.1.4.1.2272.1.21.0.67

A rcnLoopDetectMacDiscard trap signifies that a loop has been Detected on a port and the mac address will be discarded on all ports in that vlan

NTF rcnAutoRecoverPort

1.3.6.1.4.1.2272.1.21.0.68

A rcnAutoRecoverPort trap signifies that autorecover has re-enabled a port disabled by link flap or cp limit

NTF rcnAutoRecoverLoopDetectedPort

1.3.6.1.4.1.2272.1.21.0.69

A rcnAutoRecoverPort trap signifies that autorecover has cleared the action taken on a port by loop detect

NTF rcnExtCpLimitShutDown

1.3.6.1.4.1.2272.1.21.0.70

A rcnExtCpLimitShutDown trap signifies that port is shut down due to Extended CP-Limit.

NTF rcnExtCpLimitSopCongestion

1.3.6.1.4.1.2272.1.21.0.71

A rcnExtCpLimitSopCongestion signifies that system octapid polling finds that system octapid is congested or not. rcSysExtCplimitSysOctapidCongested signifies whether system octapid is congested or not. rcSysExtCplimitPortsMonitored signifies whether ports are selected for monitoring the ingress traffic utilization.

NTF rcnTacacsAuthFailure

1.3.6.1.4.1.2272.1.21.0.74

TACACS+ authentication failed for user

NTF rcnTacacsNoServers

1.3.6.1.4.1.2272.1.21.0.75

Unable to use any TACACS+ servers for authentication

NTF rcnTacacsRxUnsupportedFrame

1.3.6.1.4.1.2272.1.21.0.76

Received unsupported frame from TACACS+ server

NTF rcnTacacsExceededMaxLogins

1.3.6.1.4.1.2272.1.21.0.77

Attempted to exceed the maximum number of allowed TACACS+ logins

NTF rcnTacacsClientFailure

1.3.6.1.4.1.2272.1.21.0.78

TACACS+ Client application is down

NTF rcnVlacpPortDown

1.3.6.1.4.1.2272.1.21.0.80

A rcnVlacpPortDown trap signifies that Vlacp is down on the port specified.

NTF rcnVlacpPortUp

1.3.6.1.4.1.2272.1.21.0.81

A rcnVlacpPortUp trap signifies that Vlacp is Up on the port specified.

NTF rcnExtCpLimitShutDownNormal

1.3.6.1.4.1.2272.1.21.0.82

An rcnExtCpLimitShutDownNormal trap signifies that Ports are shut down due to Extended CP-Limit in Normal mode.

NTF rcnEapMacIntrusion

1.3.6.1.4.1.2272.1.21.0.83

A rcnEapMacIntrusion trap signifies that an EAP MAC intrusion has occured on this Port.

NTF rcnInterCpuCommStatus

1.3.6.1.4.1.2272.1.21.0.84

A rcnInterCpuCommStatus trap signifies the current communication status between primary and secondary CPU.

NTF rcPlugOptModTemperatureStatusTrap

1.3.6.1.4.1.2272.1.21.0.89

Used to trap changes in the temperature status

NTF rcPlugOptModVoltageStatusTrap

1.3.6.1.4.1.2272.1.21.0.90

Used to trap changes in the voltage level

NTF rcPlugOptModBiasStatusTrap

1.3.6.1.4.1.2272.1.21.0.91

Used to trap changes in the laser bias status

NTF rcPlugOptModTxPowerStatusTrap

1.3.6.1.4.1.2272.1.21.0.92

Used to trap changes in the transmit power status

NTF rcPlugOptModRxPowerStatusTrap

1.3.6.1.4.1.2272.1.21.0.93

Used to trap changes in the received power status

NTF rcPlugOptModAux1StatusTrap

1.3.6.1.4.1.2272.1.21.0.94

Used to trap changes in the Aux1 status

NTF rcPlugOptModAux2StatusTrap

1.3.6.1.4.1.2272.1.21.0.95

Used to trap changes in the Aux2 status

NTF rcnMaxRouteWarnClear

1.3.6.1.4.1.2272.1.21.0.110

A rcnMaxRouteWarnClear trap signifies that the number of routes in the routing table of the Virtual Router has droped below its warning threshold.

NTF rcnMaxRouteWarnSet

1.3.6.1.4.1.2272.1.21.0.111

A rcnMaxRouteWarnSet trap signifies that the given Virtual Routers routing table is reaching its maximum size. Action should be taken to prevent this

NTF rcnMaxRouteDropClear

1.3.6.1.4.1.2272.1.21.0.112

A rcnMaxRouteDropClear signifies that the given Virtual Routers routing table is no longer dropping new routes as it is below its maximum size.

NTF rcnMaxRouteDropSet

1.3.6.1.4.1.2272.1.21.0.113

A rcnMaxRouteDropSet trap signifies that the given Virtual Routers routing table has reached its maximum size, and is now dropping all new non static routes.

NTF rcnMstpNewCistRoot

1.3.6.1.4.1.2272.1.21.0.117

A rcnMstpNewCistRoot trap signifies that the SNMPv2 entity, acting in an agent role, has detected the Multiple Spanning Tree Protocol has declared the device to be the new root of the common internal spanning tree.

NTF rcnMstpNewMstiRoot

1.3.6.1.4.1.2272.1.21.0.118

A rcnMstpNewMstiRoot signifies that the SNMPv2 entity, acting in an agent role, has detected the Multiple Spanning Tree Protocol has declared the device to be the new root of the spanning tree instance.

NTF rcnMstpNewCistRegionalRoot

1.3.6.1.4.1.2272.1.21.0.119

A rcnMstpNewCistRegionalRoot trap signifies that the SNMPv2 entity, acting in an agent role, has detected the Multiple Spanning Tree Protocol has declared the device to be the new regional root of the common internal spanning tree.

NTF rcnRstpNewRoot

1.3.6.1.4.1.2272.1.21.0.120

A rcnRstpNewRoot signifies that the SNMPv2 entity, acting in an agent role, has detected the Rapid Spanning Tree Protocol has declared the device to be the new root of the spanning tree.

NTF rcnRsmltEdgePeerModified

1.3.6.1.4.1.2272.1.21.0.124

A rcnRsmltEdgePeerModified signifies that the RSMLT Peer address is different from that of the stored address. Save config is necessary if EdgeSupport has to use this info on next reboot.

NTF rcnTmuxParityError

1.3.6.1.4.1.2272.1.21.0.165

A rcnTmuxParityError trap identifies a problem in the FAD /SWIP based on the number of parity errors.

NTF rcnChasPowerSupplyNoRedundancy

1.3.6.1.4.1.2272.1.21.0.167

A rcnChasPowerSupplyNoRedundancy signifies that the chassis is running on power supply without redundancy.

NTF rcnChasPowerSupplyRedundancy

1.3.6.1.4.1.2272.1.21.0.168

A rcnChasPowerSupplyRedundancy signifies that the chassis is running on power supply with redundancy.

NTF rcnLicenseTrialPeriodExpired

1.3.6.1.4.1.2272.1.21.0.171

A rcnLicenseTrialPeriodExpired signifies that Trial Period License has expired.

NTF rcnLicenseTrialPeriodExpiry

1.3.6.1.4.1.2272.1.21.0.172

A rcnLicenseTrialPeriodExpiry signifies the time remaining before License Trial Period expires in days.

NTF rcnVrfUp

1.3.6.1.4.1.2272.1.21.0.173

This notification is generated when the specified VRF's operational status is toggled from down to up.

NTF rcnVrfDown

1.3.6.1.4.1.2272.1.21.0.174

This notification is generated when the specified VRF's operational status is toggled from up to down.

NTF rcnMrouteIngressThresholdExceeded

1.3.6.1.4.1.2272.1.21.0.175

This notification is generated when the number of mroute ingress records exceeds the ingress threshold.

NTF rcnMrouteEgressThresholdExceeded

1.3.6.1.4.1.2272.1.21.0.176

This notification is generated when the number of mroute egress records exceeds the egress threshold.

NTF rcnRemoteMirroringStatus

1.3.6.1.4.1.2272.1.21.0.177

A rcnRemoteMirroringStatus trap signifies whether the remote mirroring is enabled or disabled on a particular port

NTF rcnChasPowerSupplyRunningLow

1.3.6.1.4.1.2272.1.21.0.185

A rcnChasPowerSupplyRunningLow signifies that the chassis is running on low power supply.

NTF rcnIsisPlsbMetricMismatchTrap

1.3.6.1.4.1.2272.1.21.0.192

A PLSB ISIS trap signifies that a LSP with a different value of l1-metric is received

NTF rcnIsisPlsbDuplicateSysidTrap

1.3.6.1.4.1.2272.1.21.0.193

A PLSB ISIS trap signifies that a Hello packet with a duplicate system-id is received

NTF rcnIsisPlsbLsdbUpdateTrap

1.3.6.1.4.1.2272.1.21.0.194

A PLSB ISIS trap signifies that LSDB information has changed

NTF rcnChasFanCoolingLow

1.3.6.1.4.1.2272.1.21.0.196

A rcnChasFanCoolingLow signifies that the chassis is running on low fan cooling.

NTF rcnAuthenticationSuccess

1.3.6.1.4.1.2272.1.21.0.268

A rcnAuthenticationSuccess trap signifies that a login is success. Trap includes login username and host ip. It's deprecated by rcnaAuthenticationSuccess.

NTF rcnCardInsert

1.3.6.1.4.1.2272.1.21.0.269

A rcnCardInsert trap signifies that a card/module is inserted into the chassis

NTF rcnCardRemove

1.3.6.1.4.1.2272.1.21.0.270

A rcnCardRemove trap signifies that a card/module is removed from the chassis

NTF rcnChasFanFail

1.3.6.1.4.1.2272.1.21.0.271

A rcnChasFanFail trap indicates that a fan unit of a fan tray in a fan zone has fault.

NTF rcnChasFanOk

1.3.6.1.4.1.2272.1.21.0.272

A rcnChasFanOk trap indicates that a fan unit of a fan tray in a fan zone has recovered from previously detected fan fault.

NTF rcnCardOverheat

1.3.6.1.4.1.2272.1.21.0.273

A rcnCardOverheat trap indicates that a card temperature has exceeded the alarm threshold temperature.

NTF rcnCardNormalTemp

1.3.6.1.4.1.2272.1.21.0.274

A rcnCardNormalTemp trap indicates that a card temperature has been cool down from previously detected overheat condition.

NTF rcnCardOverheatShutDown

1.3.6.1.4.1.2272.1.21.0.275

A rcnCardOverheatShutDown trap indicates that a card has been shut down due to persistent temperature overheat for 15 minutes or temperature has exceeded the shut down threshold temperature.

NTF rcnCardCpuUtilizationHigh

1.3.6.1.4.1.2272.1.21.0.276

A rcnCardCpuUtilizationHigh trap indicates that 5-minute CPU utilization average on this slot is above 90%.

NTF rcnCardCpuUtilizationNormal

1.3.6.1.4.1.2272.1.21.0.277

A rcnCardCpuUtilizationNormal trap indicates that 5-minute CPU utilization average on this slot is below 75%.

NTF rcnIsisPlsbBvidMismatchTrap

1.3.6.1.4.1.2272.1.21.0.278

A PLSB ISIS trap signifies that a Hello packet with mismatched B-VIDs is received

NTF rcnIsisPlsbSmltVirtBmacMismatchTrap

1.3.6.1.4.1.2272.1.21.0.279

A PLSB ISIS trap signifies that Virtual BMAC configured in the switch is different from virtual BMAC configured in the IST peer

NTF rcnIsisPlsbSmltPeerBmacMismatchTrap

1.3.6.1.4.1.2272.1.21.0.280

A PLSB ISIS trap signifies that either the Smlt Peer BMAC configured in the IST peer is different from the ISIS SystemId of the local switch OR The Smlt peer BMAC configured in the local switch is different from the ISIS systemId of the IST peer

NTF rcnIsisPlsbAdjStateTrap

1.3.6.1.4.1.2272.1.21.0.281

A PLSB ISIS trap signifies ISIS adjacency state change.

NTF rcnIsisPlsbDuplicateNnameTrap

1.3.6.1.4.1.2272.1.21.0.282

A PLSB ISIS trap signifies that a LSP with duplicate nickname is received, this trap should be generated by all the switches in the network.

NTF rcnIsisPlsbSmltSplitBebMismatchTrap

1.3.6.1.4.1.2272.1.21.0.283

A PLSB ISIS trap signifies that the Smlt Split-Beb configured in the local switch and IST peer are same. One IST switch shoule be configured as Split-Beb primary and the IST peer should be configured as Split-Beb secondary.

NTF rcnIsisPlsbMultiLinkAdjTrap

1.3.6.1.4.1.2272.1.21.0.284

A PLSB ISIS trap signifies that multiple ISIS adjacencies are formed with the same ISIS node.

NTF rcnaSshSessionLogout

1.3.6.1.4.1.2272.1.21.0.285

A rcnaSshSessionLogout trap signifies that there is a SSH session logout. This trap deprecates the rcnSshSessionLogout trap.

NTF rcnaSshUnauthorizedAccess

1.3.6.1.4.1.2272.1.21.0.286

A rcnaSshUnauthorizedAccess trap signifies that an unauthorized access has occured. This trap deprecates the rcnSshUnauthorizedAccess trap.

NTF rcnaAuthenticationSuccess

1.3.6.1.4.1.2272.1.21.0.287

A rcnaAuthenticationSuccess trap signifies that a login is success. Trap includes login username and address type and inet address. This trap deprecates the rcnAuthenticationSuccess trap.

NTF rcnaSshSessionLogin

1.3.6.1.4.1.2272.1.21.0.288

A rcnaSshSessionLogin trap signifies that there is a SSH session login. This trap deprecates the rcnSshSessionLogin trap.

rcSyslog

1.3.6.1.4.1.2272.1.22

rcSyslogGlobal

1.3.6.1.4.1.2272.1.22.1

T/F rcSyslogGlobalEnable

1.3.6.1.4.1.2272.1.22.1.1

TruthValue

read-write

Used to enable/disable the SysLog feature. When enabled this feature will send a message to a server on a network that this configured to receive and store diagnostic messages from this device. The type of messages sent is user configurable.

INT rcSyslogGlobalMaxHosts

1.3.6.1.4.1.2272.1.22.1.2

INTEGER

read-write

Maximun number of remote hosts considered 'active' and able to receive messages from the Syslog service on the router.

INT rcSyslogGlobalOperState

1.3.6.1.4.1.2272.1.22.1.3

INTEGER

read-only

The operational state of the syslog service on the router.

INT rcSyslogGlobalHeader

1.3.6.1.4.1.2272.1.22.1.4

INTEGER

read-write

The IP Header Type for the Syslog Packet.

rcSyslogHostTbl

1.3.6.1.4.1.2272.1.22.2

not-accessible

Table of remote host destinations for syslog.

rcSyslogHostEntry

1.3.6.1.4.1.2272.1.22.2.1

not-accessible

Entry containing information for a particular entry in rcSyslogHostTable.

INT rcSyslogHostId

1.3.6.1.4.1.2272.1.22.2.1.1

INTEGER

read-only

Host Id.

IP rcSyslogHostIpAddr

1.3.6.1.4.1.2272.1.22.2.1.2

IpAddress

read-write

Host Ip Address

INT rcSyslogHostUdpPort

1.3.6.1.4.1.2272.1.22.2.1.3

INTEGER

read-write

Specifies the UDP port to use to send syslog messages to the host.

INT rcSyslogHostFacility

1.3.6.1.4.1.2272.1.22.2.1.4

INTEGER

read-write

Specifies the UNIX facility used in messages to the syslog host. Default is LOCAL7.

INT rcSyslogHostModuleId

1.3.6.1.4.1.2272.1.22.2.1.5

INTEGER

read-write

Specifies for which modules/tasks syslog messages should be sent. Default is all modules/tasks.

I32 rcSyslogHostModuleId2

1.3.6.1.4.1.2272.1.22.2.1.6

Integer32

read-write

Specifies for which modules/tasks syslog messages should be sent. Default is all modules/tasks.

INT rcSyslogHostSeverity

1.3.6.1.4.1.2272.1.22.2.1.7

INTEGER

read-write

Specifies the severity level for which syslog messages should be sent for the modules specifies in 'SyslogHostModule'. Value is one of multiple (logical 'OR') of the following: info(1), warning(2), error(4), mfg(8), fatal(16).

INT rcSyslogHostMapInfoSeverity

1.3.6.1.4.1.2272.1.22.2.1.8

INTEGER

read-write

Specifies the syslog severity to use for Accelar INFO messages. Default is INFO.

INT rcSyslogHostMapWarningSeverity

1.3.6.1.4.1.2272.1.22.2.1.9

INTEGER

read-write

Specifies the syslog severity to use for Accelar WARNING messages. Default is WARNING. Should be <= INFO.

INT rcSyslogHostMapErrorSeverity

1.3.6.1.4.1.2272.1.22.2.1.10

INTEGER

read-write

Specifies the syslog severity to use for Accelar ERROR messages. Default is ERROR. Should be <= WARNING.

INT rcSyslogHostMapMfgSeverity

1.3.6.1.4.1.2272.1.22.2.1.11

INTEGER

read-write

Specifies the syslog severity to use for Accelar Manufactoring messages. Dafault is ERROR.

INT rcSyslogHostMapFatalSeverity

1.3.6.1.4.1.2272.1.22.2.1.12

INTEGER

read-write

Specifies the syslog severity to use for Accelar FATAL messages. Default is EMERGENCY. Should be <= ERROR.

INT rcSyslogHostMapTraceMsg

1.3.6.1.4.1.2272.1.22.2.1.13

INTEGER

read-write

Specifies the syslog severity to use for syslog trace messages. Default is DEBUG.

INT rcSyslogHostMapTrapMsg

1.3.6.1.4.1.2272.1.22.2.1.14

INTEGER

read-write

Specifies the UNIX severity code to use for syslog messages for SNMP traps sent to the syslog host. Default is INFO.

T/F rcSyslogHostLogTraceMsgs

1.3.6.1.4.1.2272.1.22.2.1.15

TruthValue

read-write

Indicate whether to activate the host to log the syslog trace messages.

T/F rcSyslogHostLogTrapMsgs

1.3.6.1.4.1.2272.1.22.2.1.16

TruthValue

read-write

Indicate whether to activate the host to log the syslog messages for SNMP traps.

T/F rcSyslogHostEnable

1.3.6.1.4.1.2272.1.22.2.1.17

TruthValue

read-write

Enable/Disable messages to be sent to syslog host.

ROW rcSyslogHostRowStatus

1.3.6.1.4.1.2272.1.22.2.1.18

RowStatus

read-write

Used to create/delete entries in the rcSyslogTable.

IPt rcSyslogHostAddressType

1.3.6.1.4.1.2272.1.22.2.1.19

InetAddressType

read-write

Address Type of the Host.

IP rcSyslogHostAddress

1.3.6.1.4.1.2272.1.22.2.1.20

InetAddress

read-write

Address of the Host.

rcDiag

1.3.6.1.4.1.2272.1.23

rcDiagMirrorByPortTable

1.3.6.1.4.1.2272.1.23.1

not-accessible

This table is used to configure the Mirror By Port feature. This feature allows the device to forward a copy of each packet seen on a particular port to a different port.

rcDiagMirrorByPortEntry

1.3.6.1.4.1.2272.1.23.1.1

not-accessible

Entry containing mirror by port information.

INT rcDiagMirrorByPortId

1.3.6.1.4.1.2272.1.23.1.1.1

INTEGER

read-only

Entry id.

NUM rcDiagMirrorByPortMirroredPort

1.3.6.1.4.1.2272.1.23.1.1.2

InterfaceIndex

read-write

Used to configure the 'mirrored' port. The port where packets are copied from.

NUM rcDiagMirrorByPortMirroringPort

1.3.6.1.4.1.2272.1.23.1.1.3

InterfaceIndex

read-write

Used to configure the 'mirroring' port. The port where packets are copied to.

INT rcDiagMirrorByPortMode

1.3.6.1.4.1.2272.1.23.1.1.4

INTEGER

read-write

Used to configure the 'mode' of the mirror operation. 'tx' means packets being transmitted on the 'mirrored' port will be copied. 'rx' means packets received on the 'mirrored' port will be copied. 'both' means all traffic on the 'mirrored' port will be copied. 'rxFilter' means packets received on the 'mirrored' port is copied only if it macthes filter criteria. 'txFilter' means packets being transmitted on the 'mirrorred' port is copied only if it matches filter criteria. 'bothFilter' means both ingress and egress traffic will be copied if it matches either ingress or egress filter on the 'mirrored' port.

T/F rcDiagMirrorByPortEnable

1.3.6.1.4.1.2272.1.23.1.1.5

TruthValue

read-write

Used to enable/disable this entry.

ROW rcDiagMirrorByPortRowStatus

1.3.6.1.4.1.2272.1.23.1.1.6

RowStatus

read-write

Row status of this entry.

I32 rcDiagMirrorByPortPid

1.3.6.1.4.1.2272.1.23.1.1.8

Integer32

read-only

Pid for a port.

INT rcDiagMirrorRemoteMirrorVlanId

1.3.6.1.4.1.2272.1.23.1.1.9

INTEGER

read-write

vlan-id to which mirrored packets needs to be send for remote mirroring. If set, this vlan id is used in mirror tag of the remote mirrored packet

POR rcDiagMirrorByPortMirroredPortList

1.3.6.1.4.1.2272.1.23.1.1.12

PortSet

read-create

Used to configure the 'mirrored' port. The port where packets are copied from.

POR rcDiagMirrorByPortMirroringPortList

1.3.6.1.4.1.2272.1.23.1.1.13

PortSet

read-create

Used to configure the 'mirroring' port. The port where packets are copied from.

I32 rcDiagMirrorMirroringVlanId

1.3.6.1.4.1.2272.1.23.1.1.14

Integer32

read-create

Destination is a VLAN.

I32 rcDiagMirrorMirroringMltId

1.3.6.1.4.1.2272.1.23.1.1.15

Integer32

read-create

Destination is an MLT.

I32 rcDiagMirrorMirroringMgId

1.3.6.1.4.1.2272.1.23.1.1.16

Integer32

read-only

Contains information about the MGID allocated.

IP rcDiagMirrorMirroringIpAddr

1.3.6.1.4.1.2272.1.23.1.1.17

IpAddress

read-write

Destination IP address.

I32 rcDiagMirrorMirroringIpTtl

1.3.6.1.4.1.2272.1.23.1.1.18

Integer32

read-write

Ttl value for the mirrored packet when mirror destination is IP. If other than default, the encapsulated packet will have the given ttl.

I32 rcDiagMirrorMirroringIpDscp

1.3.6.1.4.1.2272.1.23.1.1.19

Integer32

read-write

Dscp value for mirrored packets when mirror destination is IP. If other than default, the encapsulated packet will have the given Dscp value.

rcDiagPortConvSteeringTable

1.3.6.1.4.1.2272.1.23.2

not-accessible

Diag Port Conv Steering Table

rcDiagPortConvSteeringEntry

1.3.6.1.4.1.2272.1.23.2.1

not-accessible

Entry containing information of Diag Port Conv Steering.

I32 rcDiagPortConvSteeringId

1.3.6.1.4.1.2272.1.23.2.1.1

Integer32

read-only

Entry id.

I32 rcDiagPortConvSteeringPortOne

1.3.6.1.4.1.2272.1.23.2.1.2

Integer32

read-write

IfIndex for port one

I32 rcDiagPortConvSteeringPortTwo

1.3.6.1.4.1.2272.1.23.2.1.3

Integer32

read-write

IfIndex for port two

INT rcDiagPortConvSteeringMode

1.3.6.1.4.1.2272.1.23.2.1.4

INTEGER

read-write

Used to specify the traffic flow that should be captured between ports one and two.

I32 rcDiagPortConvSteeringForwardPort

1.3.6.1.4.1.2272.1.23.2.1.5

Integer32

read-write

IfIndex of the port where captured traffic should be forwarded to.

T/F rcDiagPortConvSteeringEnable

1.3.6.1.4.1.2272.1.23.2.1.6

TruthValue

read-write

Enable this entry.

ROW rcDiagPortConvSteeringRowStatus

1.3.6.1.4.1.2272.1.23.2.1.7

RowStatus

read-write

Used to create/delete entries in the rcDiagMirrorByPortTable.

rcDiagMacConvSteeringTable

1.3.6.1.4.1.2272.1.23.3

not-accessible

Diag Mac Conv Steering Table

rcDiagMacConvSteeringEntry

1.3.6.1.4.1.2272.1.23.3.1

not-accessible

Entry containing information of Diag Mac Conv Steering.

I32 rcDiagMacConvSteeringId

1.3.6.1.4.1.2272.1.23.3.1.1

Integer32

read-only

Entry id.

MAC rcDiagMacConvSteeringSrcMac

1.3.6.1.4.1.2272.1.23.3.1.2

MacAddress

read-write

Source MAC address

MAC rcDiagMacConvSteeringDstMac

1.3.6.1.4.1.2272.1.23.3.1.3

MacAddress

read-write

Destination MAC address

I32 rcDiagMacConvSteeringInPort

1.3.6.1.4.1.2272.1.23.3.1.4

Integer32

read-write

IfIndex of ingress port.

I32 rcDiagMacConvSteeringForwardPort

1.3.6.1.4.1.2272.1.23.3.1.5

Integer32

read-write

IfIndex of the port where captured traffic should be forwarded to.

T/F rcDiagMacConvSteeringEnable

1.3.6.1.4.1.2272.1.23.3.1.6

TruthValue

read-write

Enable this entry.

ROW rcDiagMacConvSteeringRowStatus

1.3.6.1.4.1.2272.1.23.3.1.7

RowStatus

read-write

Used to create/delete entries in the rcDiagMirrorByPortTable.

I32 rcDiagMirrorByPortTblSize

1.3.6.1.4.1.2272.1.23.11

Integer32

read-only

Used to indicate table size.

I32 rcDiagPortConvSteeringTblSize

1.3.6.1.4.1.2272.1.23.12

Integer32

read-only

Used to indicate table size.

I32 rcDiagMacConvSteeringTblSize

1.3.6.1.4.1.2272.1.23.13

Integer32

read-only

Used to indicate table size.

rcDiagPcap

1.3.6.1.4.1.2272.1.23.15

T/F rcDiagPcapEnable

1.3.6.1.4.1.2272.1.23.15.1

TruthValue

read-write

To enable pcap in secondary CPU

T/F rcDiagPcapBufferWrap

1.3.6.1.4.1.2272.1.23.15.2

TruthValue

read-write

To enable buffer wrap-around when buffer is full. If set, pcap will continue to capture pkts, otherwise stops pkt storing

T/F rcDiagPcapPcmciaWrap

1.3.6.1.4.1.2272.1.23.15.3

TruthValue

read-write

To wrap around the PCMCIA when saving data in PCMCIA. In Vsp,the name has been changed to wrap-auto-save-file. When this parameter is true it overwrites the file present on extflash/network during autosave. If this parameter is set to false the file present is not overwritten.

INT rcDiagPcapFrameSize

1.3.6.1.4.1.2272.1.23.15.4

INTEGER

read-write

Number of bytes of pkts needs to be stored

INT rcDiagPcapBufferSize

1.3.6.1.4.1.2272.1.23.15.5

INTEGER

read-write

memory to be allocated for capturing the pkt

T/F rcDiagPcapAutoSave

1.3.6.1.4.1.2272.1.23.15.6

TruthValue

read-write

To save data automatically when buffer is full

STR rcDiagPcapAutoSaveFileName

1.3.6.1.4.1.2272.1.23.15.7

DisplayString

read-write

Name of the file in which the pkt is to be stored

INT rcDiagPcapAutoSaveDevice

1.3.6.1.4.1.2272.1.23.15.8

INTEGER

read-write

Where to store the captured pkts. If the option is network, the user need to enter an IP address also

IP rcDiagPcapAutoSaveNetworkIpAddress

1.3.6.1.4.1.2272.1.23.15.9

IpAddress

read-write

ip address of the remote host where the data needs to be stored. This field is valid only if the device is network

I32 rcDiagPcapFilterTableSize

1.3.6.1.4.1.2272.1.23.15.10

Integer32

read-only

Used to indicate the number of entries in the Filter table

rcDiagPcapFilterTable

1.3.6.1.4.1.2272.1.23.15.11

not-accessible

A table used to store pcap secondary filters

rcDiagPcapFilterEntry

1.3.6.1.4.1.2272.1.23.15.11.1

not-accessible

Pcap secondary filter desc

INT rcDiagPcapFilterId

1.3.6.1.4.1.2272.1.23.15.11.1.1

INTEGER

read-only

Unique ID that represents the filter

ENA rcDiagPcapFilterEnable

1.3.6.1.4.1.2272.1.23.15.11.1.2

EnableValue

read-write

Filter is enabled or not

INT rcDiagPcapFilterAction

1.3.6.1.4.1.2272.1.23.15.11.1.3

INTEGER

read-write

Action to be takesn when policy is matched

MAC rcDiagPcapFilterSrcMac

1.3.6.1.4.1.2272.1.23.15.11.1.4

MacAddress

read-write

Soruce mac address to match

INT rcDiagPcapFilterSrcMask

1.3.6.1.4.1.2272.1.23.15.11.1.5

INTEGER

read-write

Soruce mac address mask. Used to specify a range

T/F rcDiagPcapFilterIsInverseSrcMac

1.3.6.1.4.1.2272.1.23.15.11.1.6

TruthValue

read-write

Soruce mac address Inverse. when set the mac addresses otherthan specified is matched

MAC rcDiagPcapFilterDstMac

1.3.6.1.4.1.2272.1.23.15.11.1.7

MacAddress

read-write

Destination mac address

INT rcDiagPcapFilterDstMask

1.3.6.1.4.1.2272.1.23.15.11.1.8

INTEGER

read-write

Destination mac address mask. Used to specify a range

T/F rcDiagPcapFilterIsInverseDstMac

1.3.6.1.4.1.2272.1.23.15.11.1.9

TruthValue

read-write

Destination mac address Inverse. when set the mac addresses otherthan specified is matched

INT rcDiagPcapFilterVlanId

1.3.6.1.4.1.2272.1.23.15.11.1.10

INTEGER

read-write

Vlan-id of the packet to be matched

INT rcDiagPcapFilterToVlanId

1.3.6.1.4.1.2272.1.23.15.11.1.11

INTEGER

read-write

To Vlan-id. Used to specify a range

T/F rcDiagPcapFilterIsInverseVlanId

1.3.6.1.4.1.2272.1.23.15.11.1.12

TruthValue

read-write

Vlan-Id Inverse. when set the Vlan-Id otherthan specified range is matched

INT rcDiagPcapFilterPbit

1.3.6.1.4.1.2272.1.23.15.11.1.13

INTEGER

read-write

pBit of the packet to be matched

INT rcDiagPcapFilterToPbit

1.3.6.1.4.1.2272.1.23.15.11.1.14

INTEGER

read-write

To pBit. Used to specify a range

T/F rcDiagPcapFilterIsInversePbit

1.3.6.1.4.1.2272.1.23.15.11.1.15

TruthValue

read-write

pBit Inverse. when set the pBit otherthan specified range is matched

INT rcDiagPcapFilterEtherType

1.3.6.1.4.1.2272.1.23.15.11.1.16

INTEGER

read-write

EtherType of the packet to be matched

INT rcDiagPcapFilterToEtherType

1.3.6.1.4.1.2272.1.23.15.11.1.17

INTEGER

read-write

To EtherType. Used to specify a range

T/F rcDiagPcapFilterIsInverseEtherType

1.3.6.1.4.1.2272.1.23.15.11.1.18

TruthValue

read-write

EtherType Inverse. when set the EtherType otherthan specified range is matched

INT rcDiagPcapFilterProtocolType

1.3.6.1.4.1.2272.1.23.15.11.1.19

INTEGER

read-write

ProtocolType of the packet to be matched

INT rcDiagPcapFilterToProtocolType

1.3.6.1.4.1.2272.1.23.15.11.1.20

INTEGER

read-write

To ProtocolType. Used to specify a range

T/F rcDiagPcapFilterIsInverseProtocolType

1.3.6.1.4.1.2272.1.23.15.11.1.21

TruthValue

read-write

ProtocolType Inverse. when set the ProtocolType otherthan specified range is matched

IP rcDiagPcapFilterSrcIp

1.3.6.1.4.1.2272.1.23.15.11.1.22

IpAddress

read-write

Source IP address of the packet to be matched

IP rcDiagPcapFilterToSrcIp

1.3.6.1.4.1.2272.1.23.15.11.1.23

IpAddress

read-write

To Source IP address. Used to specify a range

T/F rcDiagPcapFilterIsInverseSrcIp

1.3.6.1.4.1.2272.1.23.15.11.1.24

TruthValue

read-write

Source IP address Inverse. when set the source IP otherthan specified range is matched

IP rcDiagPcapFilterDstIp

1.3.6.1.4.1.2272.1.23.15.11.1.25

IpAddress

read-write

Destination IP address of the packet to be matched

IP rcDiagPcapFilterToDstIp

1.3.6.1.4.1.2272.1.23.15.11.1.26

IpAddress

read-write

To Destination IP address. Used to specify a range

T/F rcDiagPcapFilterIsInverseDstIp

1.3.6.1.4.1.2272.1.23.15.11.1.27

TruthValue

read-write

Destination IP address Inverse. when set the Destination IP otherthan specified is range matched

INT rcDiagPcapFilterDscp

1.3.6.1.4.1.2272.1.23.15.11.1.28

INTEGER

read-write

DSCP value of the packet to be matched

INT rcDiagPcapFilterToDscp

1.3.6.1.4.1.2272.1.23.15.11.1.29

INTEGER

read-write

To DSCP. Used to specify a range

T/F rcDiagPcapFilterIsInverseDscp

1.3.6.1.4.1.2272.1.23.15.11.1.30

TruthValue

read-write

DSCP Inverse. when set the DSCP otherthan specified range is matched

ROW rcDiagPcapFilterRowStatus

1.3.6.1.4.1.2272.1.23.15.11.1.31

RowStatus

read-write

Row Status

T/F rcDiagPcapFilterDscpMatchZero

1.3.6.1.4.1.2272.1.23.15.11.1.32

TruthValue

read-write

When this value is set to true, then 0 value of Pbit is not taken as disable value. The user will be allowed to capture packets with Pbit value of 0 also. Be default it would be set to FALSE

T/F rcDiagPcapFilterPbitMatchZero

1.3.6.1.4.1.2272.1.23.15.11.1.33

TruthValue

read-write

When this value is set to true, then 0 value of Pbit is not taken as disable value. The user will be allowed to capture packets with Pbit value of 0 also. Be default it would be set to FALSE

I32 rcDiagPcapAdvancedFilterTableSize

1.3.6.1.4.1.2272.1.23.15.12

Integer32

read-only

Used to indicate the number of entries in the Filter table advanced parameter

rcDiagPcapAdvancedFilterTable

1.3.6.1.4.1.2272.1.23.15.13

not-accessible

A table used to store pcap secondary filters

rcDiagPcapAdvancedFilterEntry

1.3.6.1.4.1.2272.1.23.15.13.1

not-accessible

Pcap secondary Advanced filter desc

INT rcDiagPcapAdvancedFilterId

1.3.6.1.4.1.2272.1.23.15.13.1.1

INTEGER

read-only

Unique ID that represents the filter

INT rcDiagPcapAdvancedFilterUdpPort

1.3.6.1.4.1.2272.1.23.15.13.1.2

INTEGER

read-write

UdpPort of the packet to be matched

INT rcDiagPcapAdvancedFilterToUdpPort

1.3.6.1.4.1.2272.1.23.15.13.1.3

INTEGER

read-write

To UdpPort. Used to specify a range

T/F rcDiagPcapAdvancedFilterIsInverseUdpPort

1.3.6.1.4.1.2272.1.23.15.13.1.4

TruthValue

read-write

UdpPort Inverse. when set the UdpPort otherthan specified range is matched

INT rcDiagPcapAdvancedFilterTcpPort

1.3.6.1.4.1.2272.1.23.15.13.1.5

INTEGER

read-write

TcpPort of the packet to be matched

INT rcDiagPcapAdvancedFilterToTcpPort

1.3.6.1.4.1.2272.1.23.15.13.1.6

INTEGER

read-write

To TcpPort. Used to specify a range

T/F rcDiagPcapAdvancedFilterIsInverseTcpPort

1.3.6.1.4.1.2272.1.23.15.13.1.7

TruthValue

read-write

TcpPort Inverse. when set the TcpPort otherthan specified range is matched

STR rcDiagPcapAdvancedFilterUserDefinedData

1.3.6.1.4.1.2272.1.23.15.13.1.8

DisplayString

read-write

User defined data to match with the packets received

INT rcDiagPcapAdvancedFilterUserDefinedDataSize

1.3.6.1.4.1.2272.1.23.15.13.1.9

INTEGER

read-write

Length of user defined data

INT rcDiagPcapAdvancedFilterUserDefinedOffset

1.3.6.1.4.1.2272.1.23.15.13.1.10

INTEGER

read-write

Offset from which match has to start

T/F rcDiagPcapAdvancedFilterIsInverseUserDefined

1.3.6.1.4.1.2272.1.23.15.13.1.11

TruthValue

read-write

TcpPort Inverse. when set the Userdata otherthan specified is matched

INT rcDiagPcapAdvancedFilterTimer

1.3.6.1.4.1.2272.1.23.15.13.1.12

INTEGER

read-write

Timer to start the pcap capture window in ms

INT rcDiagPcapAdvancedFilterPacketCount

1.3.6.1.4.1.2272.1.23.15.13.1.13

INTEGER

read-write

Number of packets to be captured before disabling pcap

INT rcDiagPcapAdvancedFilterRefreshTimer

1.3.6.1.4.1.2272.1.23.15.13.1.14

INTEGER

read-write

Refresh timer in ms

ROW rcDiagPcapAdvancedFilterRowStatus

1.3.6.1.4.1.2272.1.23.15.13.1.15

RowStatus

read-write

RowStatus

STR rcDiagPcapCopyFileName

1.3.6.1.4.1.2272.1.23.15.14

DisplayString

read-write

Used to indicate the file name. When set, the PCAP data from PCAP engine RAM is stored into this file in PCAP engine

INT rcDiagPcapResetStat

1.3.6.1.4.1.2272.1.23.15.15

INTEGER

read-write

To Reset PCAP statistics

STR rcDiagPcapStatPacketCapacityCount

1.3.6.1.4.1.2272.1.23.15.16

DisplayString

read-only

Packet Capacity Count

STR rcDiagPcapStatNumberOfPacketsReceived

1.3.6.1.4.1.2272.1.23.15.17

DisplayString

read-only

Number of packets received in PCAP engine

STR rcDiagPcapStatNumberOfPacketsAccumulated

1.3.6.1.4.1.2272.1.23.15.18

DisplayString

read-only

Number of packets captured in PCAP engine

STR rcDiagPcapStatNumberOfPacketsDroppedInPcapEngine

1.3.6.1.4.1.2272.1.23.15.19

DisplayString

read-only

Number of packets dropped in PCAP engine by filters

STR rcDiagPcapStatNumberOfPacketsDroppedInHardware

1.3.6.1.4.1.2272.1.23.15.20

DisplayString

read-only

Number of packets dropped in Hardware

T/F rcDiagPcapDataValid

1.3.6.1.4.1.2272.1.23.15.21

TruthValue

read-only

A true/false value that indicate the return data whether is valid.

INT rcDiagPcapEtherTypeForSvlanLevel

1.3.6.1.4.1.2272.1.23.15.22

INTEGER

read-write

EtherType of svlan level.

rcIpx

1.3.6.1.4.1.2272.1.24

rcPos

1.3.6.1.4.1.2272.1.26

rcPosPppIpxTable

1.3.6.1.4.1.2272.1.26.1

not-accessible

rcPosPppIpxEntry

1.3.6.1.4.1.2272.1.26.1.1

not-accessible

NUM rcPosPppIpxIfIndex

1.3.6.1.4.1.2272.1.26.1.1.1

InterfaceIndex

read-only

port number.

INT rcPosPppIpxIpxcpAdminStatus

1.3.6.1.4.1.2272.1.26.1.1.2

INTEGER

read-write

INT rcPosPppIpxOperStatus

1.3.6.1.4.1.2272.1.26.1.1.3

INTEGER

read-only

OCT rcPosPppIpxNetAddr

1.3.6.1.4.1.2272.1.26.1.1.4

OCTET STRING

read-write

IPX Network address.

INT rcPosPppIpxRoutingProtocol

1.3.6.1.4.1.2272.1.26.1.1.5

INTEGER

read-write

rcPosSonetTable

1.3.6.1.4.1.2272.1.26.2

not-accessible

rcPosSonetEntry

1.3.6.1.4.1.2272.1.26.2.1

not-accessible

NUM rcPosSonetIndex

1.3.6.1.4.1.2272.1.26.2.1.1

InterfaceIndex

read-only

pos ifIndex.

INT rcPosSonetFraming

1.3.6.1.4.1.2272.1.26.2.1.2

INTEGER

read-write

INT rcPosSonetSectionTrace

1.3.6.1.4.1.2272.1.26.2.1.3

INTEGER

read-write

config. J0 byte

INT rcPosSonetSectionGrowth

1.3.6.1.4.1.2272.1.26.2.1.4

INTEGER

read-write

config. Z0 byte

INT rcPosSonetSyncronization

1.3.6.1.4.1.2272.1.26.2.1.5

INTEGER

read-write

config. S1 byte

OCT rcPosSonetStsPathTrace

1.3.6.1.4.1.2272.1.26.2.1.6

OCTET STRING

read-write

config. 64/16 byte.

INT rcPosSonetPathSignalLabel

1.3.6.1.4.1.2272.1.26.2.1.7

INTEGER

read-write

config. C2 byte

INT rcPosSonetClockSource

1.3.6.1.4.1.2272.1.26.2.1.8

INTEGER

read-write

ENA rcPosSonetScramble

1.3.6.1.4.1.2272.1.26.2.1.9

EnableValue

read-write

I32 rcPosSonetOperStatusFraming

1.3.6.1.4.1.2272.1.26.2.1.10

Integer32

read-only

I32 rcPosSonetOperStatusClockSource

1.3.6.1.4.1.2272.1.26.2.1.11

Integer32

read-only

ENA rcPosSonetOperStatusScramble

1.3.6.1.4.1.2272.1.26.2.1.12

EnableValue

read-only

I32 rcPosSonetOperStatusSectionTrace

1.3.6.1.4.1.2272.1.26.2.1.13

Integer32

read-only

I32 rcPosSonetOperStatusPathSignalLabel

1.3.6.1.4.1.2272.1.26.2.1.14

Integer32

read-only

rcPosLineStatusTable

1.3.6.1.4.1.2272.1.26.3

not-accessible

Pos Line Status Table

rcPosLineStatusEntry

1.3.6.1.4.1.2272.1.26.3.1

not-accessible

Entry containing information of Pos Line Status.

NUM rcPosLineStatusIndex

1.3.6.1.4.1.2272.1.26.3.1.1

InterfaceIndex

read-only

pos ifIndex, same as rcPosPppIpxIfIndex.

MAC rcPosLineStatusLocalMACAddress

1.3.6.1.4.1.2272.1.26.3.1.2

MacAddress

read-only

current local MAC address

MAC rcPosLineStatusRemoteMACAddress

1.3.6.1.4.1.2272.1.26.3.1.3

MacAddress

read-only

current remote MAC address

IP rcPosLineStatusLocalIpAddr

1.3.6.1.4.1.2272.1.26.3.1.4

IpAddress

read-only

current local ip addr

IP rcPosLineStatusRemoteIpAddr

1.3.6.1.4.1.2272.1.26.3.1.5

IpAddress

read-only

current remote ip addr

I32 rcPosLineStatusOutQuality

1.3.6.1.4.1.2272.1.26.3.1.6

Integer32

read-only

current output quality.

I32 rcPosLineStatusLocalPeriod

1.3.6.1.4.1.2272.1.26.3.1.7

Integer32

read-only

I32 rcPosLineStatusDeviceType

1.3.6.1.4.1.2272.1.26.3.1.8

Integer32

read-only

I32 rcPosLineStatusDeviceRev

1.3.6.1.4.1.2272.1.26.3.1.9

Integer32

read-only

I32 rcPosLineStatusIpxRoutingProtocol

1.3.6.1.4.1.2272.1.26.3.1.10

Integer32

read-only

rcPosLineConfigTable

1.3.6.1.4.1.2272.1.26.4

not-accessible

Pos Line Config Table

rcPosLineConfigEntry

1.3.6.1.4.1.2272.1.26.4.1

not-accessible

Entry containing information of Pos Line Config.

NUM rcPosLineConfigIndex

1.3.6.1.4.1.2272.1.26.4.1.1

InterfaceIndex

read-only

pos ifIndex, same as rcPosPppIpxIfIndex.

MAC rcPosLineConfigLocalMACAddress

1.3.6.1.4.1.2272.1.26.4.1.2

MacAddress

read-write

current local MAC address

MAC rcPosLineConfigRemoteMACAddress

1.3.6.1.4.1.2272.1.26.4.1.3

MacAddress

read-write

current remote MAC address

IP rcPosLineConfigLocalIpAddr

1.3.6.1.4.1.2272.1.26.4.1.4

IpAddress

read-write

current local ip addr

IP rcPosLineConfigRemoteIpAddr

1.3.6.1.4.1.2272.1.26.4.1.5

IpAddress

read-write

current remote ip addr

INT rcPosLineConfigRemoteReportPeriod

1.3.6.1.4.1.2272.1.26.4.1.6

INTEGER

read-write

config. remote report period.

INT rcPosLineConfigLqrThreshold

1.3.6.1.4.1.2272.1.26.4.1.7

INTEGER

read-write

config. input quality.

I32 rcPosLineConfigOutQuality

1.3.6.1.4.1.2272.1.26.4.1.8

Integer32

read-write

config. output quality.

ENA rcPosLineConfigPppStp

1.3.6.1.4.1.2272.1.26.4.1.9

EnableValue

read-write

STP PPP encoding enable T/F

T/F rcPosLineConfigLoopBack

1.3.6.1.4.1.2272.1.26.4.1.10

TruthValue

read-write

perform loop-back.

MAC rcPosLineConfigIpxVlanMacAddress

1.3.6.1.4.1.2272.1.26.4.1.11

MacAddress

read-write

MAC rcPosLineConfigIpxRemoteMacAddress

1.3.6.1.4.1.2272.1.26.4.1.12

MacAddress

read-write

rcPosSonetTrap

1.3.6.1.4.1.2272.1.26.5

INT rcPosSonetTrapType

1.3.6.1.4.1.2272.1.26.5.1

INTEGER

read-only

Used to indicate a particular type of Sonet trap.

INT rcPosSonetTrapIndication

1.3.6.1.4.1.2272.1.26.5.2

INTEGER

read-only

Used to indicate an indication for a Sonet trap.

rcPosSioCardConfigTable

1.3.6.1.4.1.2272.1.26.6

not-accessible

Pos Sio Card Config Table

rcPosSioCardConfigEntry

1.3.6.1.4.1.2272.1.26.6.1

not-accessible

Entry containing information of Pos Sio Card Config.

I32 rcPosSioCardConfigSlotIndex

1.3.6.1.4.1.2272.1.26.6.1.1

Integer32

read-only

slot Index.

INT rcPosSioCardConfigAction

1.3.6.1.4.1.2272.1.26.6.1.2

INTEGER

read-write

INT rcPosSioCardConfigTraceMode

1.3.6.1.4.1.2272.1.26.6.1.3

INTEGER

read-write

STR rcPosSioCardConfigImageFileName

1.3.6.1.4.1.2272.1.26.6.1.4

DisplayString

read-only

POS Image file name.

rcPosOperStatusTable

1.3.6.1.4.1.2272.1.26.7

not-accessible

rcPosOperStatusEntry

1.3.6.1.4.1.2272.1.26.7.1

not-accessible

NUM rcPosOperStatusIndex

1.3.6.1.4.1.2272.1.26.7.1.1

InterfaceIndex

read-only

pos ifIndex.

I32 rcPosOperStatusLqrStatus

1.3.6.1.4.1.2272.1.26.7.1.2

Integer32

read-only

Operational status of pppLqrConfigStatus.

I32 rcPosOperStatusLineLqrThreshold

1.3.6.1.4.1.2272.1.26.7.1.3

Integer32

read-only

.

I32 rcPosOperStatusLinkMagicNumber

1.3.6.1.4.1.2272.1.26.7.1.4

Integer32

read-only

.

ENA rcPosOperStatusLinePppStp

1.3.6.1.4.1.2272.1.26.7.1.5

EnableValue

read-only

rcLinkFlapDetect

1.3.6.1.4.1.2272.1.27

T/F rcLinkFlapDetectAutoPortDownEnable

1.3.6.1.4.1.2272.1.27.1

TruthValue

read-write

Used to enable/disable the Link Flap Detect feature. When enabled this feature will monitor the number of times a port goes down during a certain interval. If the number exceeds a given bound the port will be forced out-of-service.

T/F rcLinkFlapDetectSendTrap

1.3.6.1.4.1.2272.1.27.2

TruthValue

read-write

Used to configure whether a trap should be sent if the port is forced out-of-service.

INT rcLinkFlapDetectFrequency

1.3.6.1.4.1.2272.1.27.3

INTEGER

read-write

Used to configure the number of times the port can go down.

INT rcLinkFlapDetectInterval

1.3.6.1.4.1.2272.1.27.4

INTEGER

read-write

Used to configure the interval (in minutes).

rcV1Traps

1.3.6.1.4.1.2272.1.28

rcRadius

1.3.6.1.4.1.2272.1.29

rcRadiusGlobal

1.3.6.1.4.1.2272.1.29.1

T/F rcRadiusGlobalEnable

1.3.6.1.4.1.2272.1.29.1.1

TruthValue

read-write

Enable/disable this feature.

INT rcRadiusGlobalMaxNumberServer

1.3.6.1.4.1.2272.1.29.1.2

INTEGER

read-write

Maximum number of RADIUS servers.

INT rcRadiusGlobalAttributeValue

1.3.6.1.4.1.2272.1.29.1.3

INTEGER

read-write

Integer value for Access-Priority attribute.

I32 rcRadiusGlobalServerTableSize

1.3.6.1.4.1.2272.1.29.1.4

Integer32

read-only

Used to indicate the number of entries in the rcRadiusServerTable.

T/F rcRadiusGlobalAcctEnable

1.3.6.1.4.1.2272.1.29.1.5

TruthValue

read-write

Enable/disable Radius Accounting feature.

INT rcRadiusGlobalAcctAttributeValue

1.3.6.1.4.1.2272.1.29.1.6

INTEGER

read-write

Integer value for User-Command attribute.

T/F rcRadiusGlobalAcctIncludeCli

1.3.6.1.4.1.2272.1.29.1.7

TruthValue

read-write

Include/Exclude cli-commands in radius acccounting updates.

T/F rcRadiusGlobalClearStat

1.3.6.1.4.1.2272.1.29.1.8

TruthValue

read-write

Clear Radius Statistic for all servers configured.

INT rcRadiusGlobalMcastAttributeValue

1.3.6.1.4.1.2272.1.29.1.9

INTEGER

read-write

Integer value for multicast address vendor specific attribute.

INT rcRadiusGlobalAuthInfoAttributeValue

1.3.6.1.4.1.2272.1.29.1.10

INTEGER

read-write

Integer value for Auth-Info vendor specific attribute.

INT rcRadiusGlobalCommandAccess

1.3.6.1.4.1.2272.1.29.1.11

INTEGER

read-write

Integer value for Command-Access attribute.

INT rcRadiusGlobalCliCommands

1.3.6.1.4.1.2272.1.29.1.12

INTEGER

read-write

Integer value for Cli-Command attribute.

INT rcRadiusGlobalIgapLogFSize

1.3.6.1.4.1.2272.1.29.1.13

INTEGER

read-write

Maximum size for the IGAP accounting time-out log file in KB.

T/F rcRadiusGlobalCliProfEnable

1.3.6.1.4.1.2272.1.29.1.14

TruthValue

read-write

Enable/disable Radius CLI Profiling.

C32 rcRadiusGlobalAuthInvalidServerAddress

1.3.6.1.4.1.2272.1.29.1.15

Counter32

read-only

Number of Access Responses from unknown or invalid Radius servers.

T/F rcRadiusGlobalSourceIpFlag

1.3.6.1.4.1.2272.1.29.1.16

TruthValue

read-write

Flag to include configured IP address as source address in RADIUS packets.

INT rcRadiusGlobalCliCmdCount

1.3.6.1.4.1.2272.1.29.1.18

INTEGER

read-write

Integer value for Cli-Command-count.

rcRadiusServTable

1.3.6.1.4.1.2272.1.29.3

not-accessible

The RADIUS table (0 to 10 entries). This table lists the information of the RADIUS server.

rcRadiusServEntry

1.3.6.1.4.1.2272.1.29.3.1

not-accessible

A RADIUS server table entry.

INT rcRadiusServPriority

1.3.6.1.4.1.2272.1.29.3.1.1

INTEGER

read-write

Server priority, used to control which server to choose first to send authentication.

IP rcRadiusServAddress

1.3.6.1.4.1.2272.1.29.3.1.2

IpAddress

read-write

Server IP address of the RADIUS authentication server referred to in this table entry.

INT rcRadiusServTimeOut

1.3.6.1.4.1.2272.1.29.3.1.3

INTEGER

read-write

The time interval in seconds before the client retransmit the packet.

T/F rcRadiusServEnable

1.3.6.1.4.1.2272.1.29.3.1.4

TruthValue

read-write

Enable or disable this server.

INT rcRadiusServMaxRetries

1.3.6.1.4.1.2272.1.29.3.1.5

INTEGER

read-write

Maximum number of retransmissions.

INT rcRadiusServUdpPort

1.3.6.1.4.1.2272.1.29.3.1.6

INTEGER

read-write

The UDP port the client is using to send requests to this server.

STR rcRadiusServSecretKey

1.3.6.1.4.1.2272.1.29.3.1.7

DisplayString

read-write

The identifier of the RADIUS authentication client.

C32 rcRadiusServAccessRequests

1.3.6.1.4.1.2272.1.29.3.1.8

Counter32

read-only

The number of RADIUS access-response packets sent to this server. This does not include retransmissions.

C32 rcRadiusServAccessAccepts

1.3.6.1.4.1.2272.1.29.3.1.9

Counter32

read-only

The number of RADIUS access-accept packets (valid or invalid) received from this server.

C32 rcRadiusServAccessRejects

1.3.6.1.4.1.2272.1.29.3.1.10

Counter32

read-only

The number of RADIUS access-reject packets (valid or invalid) received from this server.

C32 rcRadiusServBadResponses

1.3.6.1.4.1.2272.1.29.3.1.11

Counter32

read-only

The number of RADIUS invalid access-response packets received from this server.

C32 rcRadiusServPendingRequests

1.3.6.1.4.1.2272.1.29.3.1.12

Counter32

read-only

The number of RADIUS access-request packets destined for this server that have not yet timed out or received a response. This variable is incremented when an access-request is sent and decremented due to receipt of an access-accept, access-reject, a timeout or retransmission.

C32 rcRadiusServClientRetries

1.3.6.1.4.1.2272.1.29.3.1.13

Counter32

read-only

The number of authentication retransmission to this server.

ROW rcRadiusServRowStatus

1.3.6.1.4.1.2272.1.29.3.1.14

RowStatus

read-write

Used to create/delete entries.

T/F rcRadiusServAcctEnable

1.3.6.1.4.1.2272.1.29.3.1.15

TruthValue

read-write

Enable or disable Radius Accounting on this server.

INT rcRadiusServAcctUdpPort

1.3.6.1.4.1.2272.1.29.3.1.16

INTEGER

read-write

The UDP port the client used to send accounting requests to this server.

C32 rcRadiusServAcctOnRequests

1.3.6.1.4.1.2272.1.29.3.1.17

Counter32

read-only

The number of RADIUS accounting-on packets sent to this server. This does not include retransmissions.

C32 rcRadiusServAcctOffRequests

1.3.6.1.4.1.2272.1.29.3.1.18

Counter32

read-only

The number of RADIUS accounting-off packets sent to this server. This does not include retransmissions.

C32 rcRadiusServAcctStartRequests

1.3.6.1.4.1.2272.1.29.3.1.19

Counter32

read-only

The number of RADIUS accounting-start packets sent to this server. This does not include retransmissions.

C32 rcRadiusServAcctStopRequests

1.3.6.1.4.1.2272.1.29.3.1.20

Counter32

read-only

The number of RADIUS accounting-stop packets sent to this server. This does not include retransmissions.

C32 rcRadiusServAcctInterimRequests

1.3.6.1.4.1.2272.1.29.3.1.21

Counter32

read-only

The number of RADIUS accounting-interim packets sent to this server. This does not include retransmissions.

C32 rcRadiusServAcctBadResponses

1.3.6.1.4.1.2272.1.29.3.1.22

Counter32

read-only

The number of Invalid responses received from this server.

C32 rcRadiusServAcctPendingRequests

1.3.6.1.4.1.2272.1.29.3.1.23

Counter32

read-only

The number of RADIUS accounting packets that are waiting be sent to this server. This variable is incremented whenever any accounting-request is sent to this server and decremented when an acknowledgement is received or timeout occurs.

C32 rcRadiusServAcctClientRetries

1.3.6.1.4.1.2272.1.29.3.1.24

Counter32

read-only

The number of RADIUS accounting packets retransmitted to this server.

INT rcRadiusServUsedBy

1.3.6.1.4.1.2272.1.29.3.1.25

INTEGER

read-only

cli(1): for cli login, igap(2): for igap,snmp(3): for snmp login, eap(4) for EAP PAE Authenticator web(5) for web-server(http/https) login.

IP rcRadiusServNasIpAddress

1.3.6.1.4.1.2272.1.29.3.1.26

IpAddress

read-only

RADIUS Client NAS Identifier for this server.

STR rcRadiusServRoundTripTime

1.3.6.1.4.1.2272.1.29.3.1.27

DisplayString

read-only

Time different between the instance when a RADIUS request is sent and the corresponding response is received.

C32 rcRadiusServAccessChallanges

1.3.6.1.4.1.2272.1.29.3.1.28

Counter32

read-only

The number of RADIUS access-challanges packets sent to this server. This does not include retransmission.

IP rcRadiusServSourceIpAddr

1.3.6.1.4.1.2272.1.29.3.1.29

IpAddress

read-write

source IP address RADIUS packets.

rcRadiusGlobalSnmp

1.3.6.1.4.1.2272.1.29.4

T/F rcRadiusGlobalSnmpEnable

1.3.6.1.4.1.2272.1.29.4.1

TruthValue

read-write

Enable/disable snmp radius authentication.

T/F rcRadiusGlobalSnmpAcctEnable

1.3.6.1.4.1.2272.1.29.4.2

TruthValue

read-write

Enable/disable Radius Accounting for SNMP.

INT rcRadiusGlobalSnmpReAuthenticateTimer

1.3.6.1.4.1.2272.1.29.4.3

INTEGER

read-write

Integer value representing Re-Authenticate Timer in seconds. Timer to be used to Re- Authenticate a SNMP Session.

INT rcRadiusGlobalSnmpAbortSessionTimer

1.3.6.1.4.1.2272.1.29.4.4

INTEGER

read-write

Integer value representing the time in seconds after which the snmp session is considered expired and Radius Accounting Stop message is sent.

STR rcRadiusGlobalSnmpUserName

1.3.6.1.4.1.2272.1.29.4.5

DisplayString

read-write

User name for Radius SNMP Accounting.

MAC rcRadiusEapLastRejMac

1.3.6.1.4.1.2272.1.29.4.6

MacAddress

read-only

Used to store the Last Rejected MAC address on an EAP enabled port.

NUM rcRadiusPaePortNumber

1.3.6.1.4.1.2272.1.29.4.7

InterfaceIndex

read-only

Used to store the Port Number on which the Mac Intrusion happened.

MAC rcRadiusEapLastAuthMac

1.3.6.1.4.1.2272.1.29.4.8

MacAddress

read-only

Used to store the Last Authenticated MAC address on an EAP enabled port.

rcRadiusServHostTable

1.3.6.1.4.1.2272.1.29.5

not-accessible

The RADIUS Server Host table (0 to 10 entries). This table lists the information of the RADIUS server.

rcRadiusServHostEntry

1.3.6.1.4.1.2272.1.29.5.1

not-accessible

A RADIUS server table entry.

IPt rcRadiusServHostAddressType

1.3.6.1.4.1.2272.1.29.5.1.1

InetAddressType

not-accessible

Inet Address Type of radius server host address.

IP rcRadiusServHostAddress

1.3.6.1.4.1.2272.1.29.5.1.2

InetAddress

not-accessible

Server IP address of the RADIUS authentication server referred to in this table entry.

INT rcRadiusServHostUsedBy

1.3.6.1.4.1.2272.1.29.5.1.3

INTEGER

not-accessible

cli(1): for cli login, igap(2): for igap,snmp(3): for snmp login, eap(4) for EAP PAE Authenticator web(5) for web-server(http/https) login. IGAP is not supported on the VSP 9000.

I32 rcRadiusServHostPriority

1.3.6.1.4.1.2272.1.29.5.1.4

Integer32

read-create

Server priority, used to control which server to choose first to send authentication.

I32 rcRadiusServHostTimeOut

1.3.6.1.4.1.2272.1.29.5.1.5

Integer32

read-create

The time interval in seconds before the client retransmit the packet.

T/F rcRadiusServHostEnable

1.3.6.1.4.1.2272.1.29.5.1.6

TruthValue

read-create

Enable or disable this server.

I32 rcRadiusServHostMaxRetries

1.3.6.1.4.1.2272.1.29.5.1.7

Integer32

read-create

Maximum number of retransmissions.

I32 rcRadiusServHostUdpPort

1.3.6.1.4.1.2272.1.29.5.1.8

Integer32

read-create

The UDP port the client is using to send requests to this server.

STR rcRadiusServHostSecretKey

1.3.6.1.4.1.2272.1.29.5.1.9

DisplayString

read-create

The identifier of the RADIUS authentication client.

C32 rcRadiusServHostAccessRequests

1.3.6.1.4.1.2272.1.29.5.1.10

Counter32

read-only

The number of RADIUS access-response packets sent to this server. This does not include retransmissions.

C32 rcRadiusServHostAccessAccepts

1.3.6.1.4.1.2272.1.29.5.1.11

Counter32

read-only

The number of RADIUS access-accept packets (valid or invalid) received from this server.

C32 rcRadiusServHostAccessRejects

1.3.6.1.4.1.2272.1.29.5.1.12

Counter32

read-only

The number of RADIUS access-reject packets (valid or invalid) received from this server.

C32 rcRadiusServHostBadResponses

1.3.6.1.4.1.2272.1.29.5.1.13

Counter32

read-only

The number of RADIUS invalid access-response packets received from this server.

C32 rcRadiusServHostPendingRequests

1.3.6.1.4.1.2272.1.29.5.1.14

Counter32

read-only

The number of RADIUS access-request packets destined for this server that have not yet timed out or received a response. This variable is incremented when an access-request is sent and decremented due to receipt of an access-accept, access-reject, a timeout or retransmission.

C32 rcRadiusServHostClientRetries

1.3.6.1.4.1.2272.1.29.5.1.15

Counter32

read-only

The number of authentication retransmission to this server.

ROW rcRadiusServHostRowStatus

1.3.6.1.4.1.2272.1.29.5.1.16

RowStatus

read-create

Used to create/delete entries.

T/F rcRadiusServHostAcctEnable

1.3.6.1.4.1.2272.1.29.5.1.17

TruthValue

read-create

Enable or disable Radius Accounting on this server.

I32 rcRadiusServHostAcctUdpPort

1.3.6.1.4.1.2272.1.29.5.1.18

Integer32

read-create

The UDP port the client used to send accounting requests to this server.

C32 rcRadiusServHostAcctOnRequests

1.3.6.1.4.1.2272.1.29.5.1.19

Counter32

read-only

The number of RADIUS accounting-on packets sent to this server. This does not include retransmissions.

C32 rcRadiusServHostAcctOffRequests

1.3.6.1.4.1.2272.1.29.5.1.20

Counter32

read-only

The number of RADIUS accounting-off packets sent to this server. This does not include retransmissions.

C32 rcRadiusServHostAcctStartRequests

1.3.6.1.4.1.2272.1.29.5.1.21

Counter32

read-only

The number of RADIUS accounting-start packets sent to this server. This does not include retransmissions.

C32 rcRadiusServHostAcctStopRequests

1.3.6.1.4.1.2272.1.29.5.1.22

Counter32

read-only

The number of RADIUS accounting-stop packets sent to this server. This does not include retransmissions.

C32 rcRadiusServHostAcctInterimRequests

1.3.6.1.4.1.2272.1.29.5.1.23

Counter32

read-only

The number of RADIUS accounting-interim packets sent to this server. This does not include retransmissions.

C32 rcRadiusServHostAcctBadResponses

1.3.6.1.4.1.2272.1.29.5.1.24

Counter32

read-only

The number of Invalid responses received from this server.

C32 rcRadiusServHostAcctPendingRequests

1.3.6.1.4.1.2272.1.29.5.1.25

Counter32

read-only

The number of RADIUS accounting packets that are waiting be sent to this server. This variable is incremented whenever any accounting-request is sent to this server and decremented when an acknowledgement is received or timeout occurs.

C32 rcRadiusServHostAcctClientRetries

1.3.6.1.4.1.2272.1.29.5.1.26

Counter32

read-only

The number of RADIUS accounting packets retransmitted to this server.

IP rcRadiusServHostNasIpAddress

1.3.6.1.4.1.2272.1.29.5.1.27

InetAddress

read-only

RADIUS Client NAS Identifier for this server.

STR rcRadiusServHostRoundTripTime

1.3.6.1.4.1.2272.1.29.5.1.28

DisplayString

read-only

Time different between the instance when a RADIUS request is sent and the corresponding response is received.

C32 rcRadiusServHostAccessChallanges

1.3.6.1.4.1.2272.1.29.5.1.29

Counter32

read-only

The number of RADIUS access-challanges packets sent to this server. This does not include retransmission.

IP rcRadiusServHostSourceIpAddr

1.3.6.1.4.1.2272.1.29.5.1.30

InetAddress

read-create

source IP address RADIUS packets.

rcIgmp

1.3.6.1.4.1.2272.1.30

rcIgmpInterfaceExtnTable

1.3.6.1.4.1.2272.1.30.1

not-accessible

rcIgmpInterfaceExtnEntry

1.3.6.1.4.1.2272.1.30.1.1

not-accessible

NUM rcIgmpInterfaceExtnIfIndex

1.3.6.1.4.1.2272.1.30.1.1.1

InterfaceIndex

read-only

ifindex.

T/F rcIgmpInterfaceExtnSnoopEnable

1.3.6.1.4.1.2272.1.30.1.1.2

TruthValue

read-write

enable snoop.

T/F rcIgmpInterfaceExtnProxySnoopEnable

1.3.6.1.4.1.2272.1.30.1.1.3

TruthValue

read-write

enable proxy snoop.

INT rcIgmpInterfaceExtnMaxAdvertiseInterval

1.3.6.1.4.1.2272.1.30.1.1.4

INTEGER

read-write

INT rcIgmpInterfaceExtnMinAdvertiseInterval

1.3.6.1.4.1.2272.1.30.1.1.5

INTEGER

read-write

I32 rcIgmpInterfaceExtnMaxInitialAdvertiseInterval

1.3.6.1.4.1.2272.1.30.1.1.6

Integer32

read-write

I32 rcIgmpInterfaceExtnMaxInitialAdvertments

1.3.6.1.4.1.2272.1.30.1.1.7

Integer32

read-write

I32 rcIgmpInterfaceExtnNeighborDeadInterval

1.3.6.1.4.1.2272.1.30.1.1.8

Integer32

read-write

T/F rcIgmpInterfaceExtnFastLeaveEnable

1.3.6.1.4.1.2272.1.30.1.1.9

TruthValue

read-write

Enable fast leave on this interface.

POR rcIgmpInterfaceExtnFastLeavePortMembers

1.3.6.1.4.1.2272.1.30.1.1.10

PortSet

read-write

The set of ports that are enabled for fast leave.

T/F rcIgmpInterfaceExtnMrdiscEnable

1.3.6.1.4.1.2272.1.30.1.1.11

TruthValue

read-write

Enable/disable multicast router discovery.

POR rcIgmpInterfaceExtnDiscoveredRouterPorts

1.3.6.1.4.1.2272.1.30.1.1.12

PortSet

read-only

list of ports that discovered by IGMP Multicast router discovery (MRDISC) protocol.

POR rcIgmpInterfaceExtnSnoopMRouterPorts

1.3.6.1.4.1.2272.1.30.1.1.13

PortSet

read-write

The set of ports in this interface that provide connectivity to an IP Multicast router.

POR rcIgmpInterfaceExtnSnoopActiveMRouterPorts

1.3.6.1.4.1.2272.1.30.1.1.14

PortSet

read-only

Active ports.

I32 rcIgmpInterfaceExtnSnoopMRouterExpiration

1.3.6.1.4.1.2272.1.30.1.1.15

Integer32

read-only

Multicast querier router aging time out.

INT rcIgmpInterfaceExtnFlushAction

1.3.6.1.4.1.2272.1.30.1.1.16

INTEGER

read-write

IGMP flush action.

ENA rcIgmpInterfaceExtnRouterAlertEnable

1.3.6.1.4.1.2272.1.30.1.1.17

EnableValue

read-write

Enable Router Alert Check.

T/F rcIgmpInterfaceExtnSsmEnable

1.3.6.1.4.1.2272.1.30.1.1.18

TruthValue

read-write

enable SSM.

ENA rcIgmpInterfaceExtnAccntEnable

1.3.6.1.4.1.2272.1.30.1.1.20

EnableValue

read-write

enable/disable accounting.

ENA rcIgmpInterfaceExtnAuthEnable

1.3.6.1.4.1.2272.1.30.1.1.21

EnableValue

read-write

enable/disable authentication.

ENA rcIgmpInterfaceExtnStreamLimitEnable

1.3.6.1.4.1.2272.1.30.1.1.22

EnableValue

read-write

Stream Limitation enable/disable.

I32 rcIgmpInterfaceExtnMaxStreams

1.3.6.1.4.1.2272.1.30.1.1.23

Integer32

read-write

Maximum number of stream.

I32 rcIgmpInterfaceExtnNumStreams

1.3.6.1.4.1.2272.1.30.1.1.24

Integer32

read-only

Current number of streams.

IP rcIgmpInterfaceExtnNewQuerier

1.3.6.1.4.1.2272.1.30.1.1.25

IpAddress

read-only

The address of the New IGMP Querier on the IP subnet to which this interface is attached.

T/F rcIgmpInterfaceExtnSnoopQuerierEnable

1.3.6.1.4.1.2272.1.30.1.1.26

TruthValue

read-write

enable snoop querier.

IP rcIgmpInterfaceExtnSnoopQuerierAddr

1.3.6.1.4.1.2272.1.30.1.1.27

IpAddress

read-write

The pseudo address of the IGMP Snoop Querier.

T/F rcIgmpInterfaceExtnMvrEnable

1.3.6.1.4.1.2272.1.30.1.1.28

TruthValue

read-write

Enable or disable mcast-vlan-registration on a vlan, it is used to specified a vlan works as a mcast-vlan, maximum 16 mcast-vlan is supported.

T/F rcIgmpInterfaceExtnMvrProxyEnable

1.3.6.1.4.1.2272.1.30.1.1.29

TruthValue

read-write

enable or disable mcast-vlan-registration proxy on a vlan, you must enable mcast-vlan-registration at first.

T/F rcIgmpInterfaceExtnDynamicDowngradeEnable

1.3.6.1.4.1.2272.1.30.1.1.30

TruthValue

read-write

enable dynamic downgrade the IGMP version when older version query message was received.

T/F rcIgmpInterfaceExtnCompatibilityModeEnable

1.3.6.1.4.1.2272.1.30.1.1.31

TruthValue

read-write

enable v2 v3 compatible mode, which will handle the IGMP v2 message in v3 interface

INT rcIgmpInterfaceExtnOperVersion

1.3.6.1.4.1.2272.1.30.1.1.32

INTEGER

read-only

The operational version of IGMP which is running on this interface.

T/F rcIgmpInterfaceExtnExplicitHostTrackingEnable

1.3.6.1.4.1.2272.1.30.1.1.33

TruthValue

read-write

Enable the IGMP protocol running in version 3 to track hosts per channels/groups.

rcIgmpStaticTable

1.3.6.1.4.1.2272.1.30.2

not-accessible

rcIgmpStaticEntry

1.3.6.1.4.1.2272.1.30.2.1

not-accessible

NUM rcIgmpStaticIfIndex

1.3.6.1.4.1.2272.1.30.2.1.1

InterfaceIndex

read-only

ifindex

IP rcIgmpStaticGrpAddr

1.3.6.1.4.1.2272.1.30.2.1.2

IpAddress

read-only

Ip multicast address. The GrpAddress holds the starting range for the address range. If the ToGrpAddress is not entered, the it is as good as entering a single address.

POR rcIgmpStaticMemberPorts

1.3.6.1.4.1.2272.1.30.2.1.3

PortSet

read-write

egressing ports.

POR rcIgmpStaticNotAllowedToJoin

1.3.6.1.4.1.2272.1.30.2.1.4

PortSet

read-write

not allowed to join.

ROW rcIgmpStaticRowStatus

1.3.6.1.4.1.2272.1.30.2.1.5

RowStatus

read-write

Used to create/delete entries in the rcIgmpStaticEntry.

IP rcIgmpStaticToGrpAddr

1.3.6.1.4.1.2272.1.30.2.1.6

IpAddress

read-write

To hold the range for the GrpAddress.

rcIgmpAccessTable

1.3.6.1.4.1.2272.1.30.3

not-accessible

rcIgmpAccessEntry

1.3.6.1.4.1.2272.1.30.3.1

not-accessible

NUM rcIgmpAccessIfIndex

1.3.6.1.4.1.2272.1.30.3.1.1

InterfaceIndex

read-only

ifindex

IP rcIgmpAccessGrpAddr

1.3.6.1.4.1.2272.1.30.3.1.2

IpAddress

read-only

ip multicast addr.

IP rcIgmpAccessHostAddr

1.3.6.1.4.1.2272.1.30.3.1.3

IpAddress

read-only

host addr.

INT rcIgmpAccessMode

1.3.6.1.4.1.2272.1.30.3.1.4

INTEGER

read-write

denyTX(1), denyRX(2), denyBOTH(3).

ROW rcIgmpAccessRowStatus

1.3.6.1.4.1.2272.1.30.3.1.5

RowStatus

read-write

Used to create/delete entries in the rcIgmpAccessEntry.

IP rcIgmpAccessHostMask

1.3.6.1.4.1.2272.1.30.3.1.6

IpAddress

read-only

host mask.

rcIgmpSenderTable

1.3.6.1.4.1.2272.1.30.4

not-accessible

rcIgmpSenderEntry

1.3.6.1.4.1.2272.1.30.4.1

not-accessible

IP rcIgmpSenderGrpAddr

1.3.6.1.4.1.2272.1.30.4.1.1

IpAddress

read-only

ip multicast addr.

NUM rcIgmpSenderIfIndex

1.3.6.1.4.1.2272.1.30.4.1.2

InterfaceIndex

read-only

ifindex

IP rcIgmpSenderMemberAddr

1.3.6.1.4.1.2272.1.30.4.1.3

IpAddress

read-only

host addr.

INT rcIgmpSenderAction

1.3.6.1.4.1.2272.1.30.4.1.4

INTEGER

read-write

none(0), flushEntry(1), flushGrp(2).

I32 rcIgmpSenderTPort

1.3.6.1.4.1.2272.1.30.4.1.5

Integer32

read-only

Igmp Sender Tport.

INT rcIgmpSenderState

1.3.6.1.4.1.2272.1.30.4.1.6

INTEGER

read-only

Indicates if a sender exists because of an IGMP access filter or not.

rcIgmpSsmGlobal

1.3.6.1.4.1.2272.1.30.5

T/F rcIgmpSsmGlobalDynamicLearning

1.3.6.1.4.1.2272.1.30.5.1

TruthValue

read-write

Enable/disable dynamic learning or source/group pair from IGMPv3 report.

INT rcIgmpSsmGlobalAdminAction

1.3.6.1.4.1.2272.1.30.5.2

INTEGER

read-write

Set the admin status of all the Ssm entries to enable/disable at once.

IP rcIgmpSsmGlobalRangeGroup

1.3.6.1.4.1.2272.1.30.5.3

IpAddress

read-write

If multicast group address & RangeMask == RangeGroup, then RangeGroup is in Ssm Range. Else it is not in the range.

IP rcIgmpSsmGlobalRangeMask

1.3.6.1.4.1.2272.1.30.5.4

IpAddress

read-write

Used with RangeGroup.

rcIgmpSsmTable

1.3.6.1.4.1.2272.1.30.6

not-accessible

rcIgmpSsmEntry

1.3.6.1.4.1.2272.1.30.6.1

not-accessible

IP rcIgmpSsmIpMulticastGrp

1.3.6.1.4.1.2272.1.30.6.1.1

IpAddress

read-only

This is the IP multicast group address that has default range of 232/8. This parameter should be configured by the user.

IP rcIgmpSsmIpSource

1.3.6.1.4.1.2272.1.30.6.1.2

IpAddress

read-write

This is the Source's IP address that will be sending traffic to the group source. This parameter should be configured by the user.

INT rcIgmpSsmLearningMode

1.3.6.1.4.1.2272.1.30.6.1.3

INTEGER

read-only

This is a read only field that provides information if the entry is statically configured entry (Static) or a dynamically learned entry from IGMPv3 (Dynamic). Note that Dynamic may not be used in the first step of the implementation.

T/F rcIgmpSsmActivity

1.3.6.1.4.1.2272.1.30.6.1.4

TruthValue

read-only

This is a read only field. It provides the activity on the corresponding (S,G). If the source is active and traffic is flowing to the switch, this field value should be Active, otherwise it should say non-active. This information is useful in knowing if the group has an active source or not when the group is joined by a member on the switch.

ENA rcIgmpSsmAdminState

1.3.6.1.4.1.2272.1.30.6.1.5

EnableValue

read-write

The admin state provides information on whether the entry is to be used or not. If the value of this field is Enabled (default), then the entry can be used. If the state is Disabled, then the entry will not be used, but will be saved for future use.

ROW rcIgmpSsmRowStatus

1.3.6.1.4.1.2272.1.30.6.1.6

RowStatus

read-write

Used to create/delete entries.

rcIgmpNewAccessTable

1.3.6.1.4.1.2272.1.30.7

not-accessible

rcIgmpNewAccessEntry

1.3.6.1.4.1.2272.1.30.7.1

not-accessible

NUM rcIgmpNewAccessIfIndex

1.3.6.1.4.1.2272.1.30.7.1.1

InterfaceIndex

read-only

ifindex

I32 rcIgmpNewAccessPrefixListId

1.3.6.1.4.1.2272.1.30.7.1.2

Integer32

read-only

Prefix List ID.

STR rcIgmpNewAccessPrefixListName

1.3.6.1.4.1.2272.1.30.7.1.3

DisplayString

read-write

Prefix List name.

IP rcIgmpNewAccessHostAddr

1.3.6.1.4.1.2272.1.30.7.1.4

IpAddress

read-only

host addr.

IP rcIgmpNewAccessHostMask

1.3.6.1.4.1.2272.1.30.7.1.5

IpAddress

read-only

host mask.

INT rcIgmpNewAccessActionMode

1.3.6.1.4.1.2272.1.30.7.1.6

INTEGER

read-write

action mode.

ROW rcIgmpNewAccessRowStatus

1.3.6.1.4.1.2272.1.30.7.1.7

RowStatus

read-write

Used to create/delete entries in the rcIgmpNewAccessEntry.

rcIgmpChannelLimitTable

1.3.6.1.4.1.2272.1.30.8

not-accessible

rcIgmpChannelLimitEntry

1.3.6.1.4.1.2272.1.30.8.1

not-accessible

NUM rcIgmpChannelLimitIfIndex

1.3.6.1.4.1.2272.1.30.8.1.1

InterfaceIndex

read-only

ifindex

I32 rcIgmpChannelLimitPort

1.3.6.1.4.1.2272.1.30.8.1.2

Integer32

read-only

The port belong to this vlan.

I32 rcIgmpChannelLimitMaxStreams

1.3.6.1.4.1.2272.1.30.8.1.3

Integer32

read-write

Maximum number of stream.

I32 rcIgmpChannelLimitNumStreams

1.3.6.1.4.1.2272.1.30.8.1.4

Integer32

read-only

Current number of streams.

ROW rcIgmpChannelLimitRowStatus

1.3.6.1.4.1.2272.1.30.8.1.5

RowStatus

read-write

Row Status.

rcIgmpGlobalParams

1.3.6.1.4.1.2272.1.30.11

INT rcIgmpFastLeaveMode

1.3.6.1.4.1.2272.1.30.11.1

INTEGER

read-write

Set the fast-leave mode to be used by for all fast-leave enabled IGMP interfaces.

ENA rcIgmpGenerateTrap

1.3.6.1.4.1.2272.1.30.11.2

EnableValue

read-write

Enabling the IGMP to generate trap.

ENA rcIgmpGenerateLog

1.3.6.1.4.1.2272.1.30.11.3

EnableValue

read-write

Enabling the IGMP to generate log.

rcIgmpCacheExtnTable

1.3.6.1.4.1.2272.1.30.12

not-accessible

rcIgmpCacheExtnEntry

1.3.6.1.4.1.2272.1.30.12.1

not-accessible

INT rcIgmpCacheExtnType

1.3.6.1.4.1.2272.1.30.12.1.1

INTEGER

read-only

It takes up either of the two values, dynamic or static depending upon whether the entry is learnt Dynamic or is added statically.

POR rcIgmpCacheExtnStaticPorts

1.3.6.1.4.1.2272.1.30.12.1.2

PortSet

read-only

It displays the static ports for the static joins, this would be null for the dynamic entry.

rcIgmpSnoopTraceTable

1.3.6.1.4.1.2272.1.30.13

not-accessible

The table listing the multicast groups traversing the snoop enabled router

rcIgmpSnoopTraceEntry

1.3.6.1.4.1.2272.1.30.13.1

not-accessible

The entry listing the multicast groups traversing the snoop enabled router

IP rcIgmpSnoopGrpAddr

1.3.6.1.4.1.2272.1.30.13.1.1

IpAddress

not-accessible

ip mcast addr of grp traversing the router

IP rcIgmpSnoopSrcAddr

1.3.6.1.4.1.2272.1.30.13.1.2

IpAddress

not-accessible

Ip src addr of the mcast grp address

NUM rcIgmpSnoopOutVlan

1.3.6.1.4.1.2272.1.30.13.1.3

InterfaceIndex

not-accessible

Egress vlan id for the mcast group

NUM rcIgmpSnoopInPort

1.3.6.1.4.1.2272.1.30.13.1.4

InterfaceIndex

read-only

Ingress port for the mcast grp

NUM rcIgmpSnoopInVlan

1.3.6.1.4.1.2272.1.30.13.1.5

InterfaceIndex

read-only

Ingress vlan id for the mcast source

POR rcIgmpSnoopOutPort

1.3.6.1.4.1.2272.1.30.13.1.6

PortSet

read-only

Egress port of the mcast grp

rcIgmpNewGroupTable

1.3.6.1.4.1.2272.1.30.14

not-accessible

The (conceptual) table listing the multicast groups configured in the device.

rcIgmpNewGroupEntry

1.3.6.1.4.1.2272.1.30.14.1

not-accessible

An entry (conceptual row) representing an Igmp group.

IP rcIgmpNewGroupIpAddress

1.3.6.1.4.1.2272.1.30.14.1.1

IpAddress

not-accessible

Multicast group Address (Class D) that others want to join. A group address can be the same for many incoming ports.

IP rcIgmpNewGroupMembers

1.3.6.1.4.1.2272.1.30.14.1.2

IpAddress

not-accessible

IP Address of a source that has sent group report wishing to join this group.

INT rcIgmpNewGroupInPort

1.3.6.1.4.1.2272.1.30.14.1.3

INTEGER

not-accessible

An unique value to identify a physical interface or a logical interface (VLAN), which has received Group reports from various sources.

I32 rcIgmpNewGroupExpiration

1.3.6.1.4.1.2272.1.30.14.1.4

Integer32

read-only

Time left before the group report expired on this port. Only one of this variable port. This variable is updated upon receiving a group report.

NUM rcIgmpNewGroupIfIndex

1.3.6.1.4.1.2272.1.30.14.1.5

InterfaceIndex

read-only

An unique value to identify a physical interface or a logical interface (VLAN), which has received Group reports from various sources.

STR rcIgmpNewGroupUserId

1.3.6.1.4.1.2272.1.30.14.1.6

DisplayString

read-only

User-id sending this group

INT rcIgmpNewGroupMemberState

1.3.6.1.4.1.2272.1.30.14.1.7

INTEGER

read-only

Used for IGAP, to indicated member state.

I32 rcIgmpNewGroupSessionTime

1.3.6.1.4.1.2272.1.30.14.1.8

Integer32

read-only

Used for IGAP, to indicated the session time in seconds for the member. Session time is started after traffic is available to member. It can be also called AccountingTime since its values correspondes to the accounting duration of IGAP user session.

rcIgmpv3CacheTable

1.3.6.1.4.1.2272.1.30.24

not-accessible

The (conceptual) table listing the Igmpv3 specific data corresponding to each interface, port and multicast group pair on a Router.

rcIgmpv3CacheEntry

1.3.6.1.4.1.2272.1.30.24.1

not-accessible

An entry (conceptual row) representing an Igmpv3 Group.

IP rcIgmpv3CacheEntryGroupAddress

1.3.6.1.4.1.2272.1.30.24.1.1

IpAddress

not-accessible

Multicast group Address (Class D) that others want to join. A group address can be the same for many incoming ports.

NUM rcIgmpv3CacheEntryIfIndex

1.3.6.1.4.1.2272.1.30.24.1.2

InterfaceIndex

not-accessible

An unique value to identify a physical interface or a logical interface (VLAN), which has received Group reports from various sources.

INT rcIgmpv3CacheEntryInPort

1.3.6.1.4.1.2272.1.30.24.1.3

INTEGER

not-accessible

An unique value to identify a physical interface or a logical interface (VLAN), which has received Group reports from various sources.

I32 rcIgmpv3CacheEntryModeExpiryTimer

1.3.6.1.4.1.2272.1.30.24.1.4

Integer32

read-only

This value is applicable only to IGMPv3-compatible nodes and represents the time remaining before the interface EXCLUDE state expires and the interface state transitions to INCLUDE mode. This value can never be greater than rcIgmpNewGroupExpiration.

I32 rcIgmpv3CacheEntryVersion1HostTimer

1.3.6.1.4.1.2272.1.30.24.1.5

Integer32

read-only

The time remaining until the local router will assume that there are no longer any IGMP version 1 members on the IP subnet attached to this interface. This entry only applies to IGMPv1 hosts. Upon hearing any IGMPv1 Report, this value is reset to the group membership timer. While this time remaining is non-zero, the local router ignores any IGMPv2 Leave messages for this group that it receives on this interface.

I32 rcIgmpv3CacheEntryVersion2HostTimer

1.3.6.1.4.1.2272.1.30.24.1.6

Integer32

read-only

The time remaining until the local router will assume that there are no longer any IGMP version 2 members on the IP subnet attached to this interface. Upon hearing any IGMPv2 Membership Report, this value is reset to the group membership timer. Assuming no IGMPv1 hosts have been detected, the local router does not ignore any IGMPv2 Leave messages for this group that it receives on this interface.

INT rcIgmpv3CacheEntrySourceFilterMode

1.3.6.1.4.1.2272.1.30.24.1.7

INTEGER

read-only

The current group state, applicable to IGMPv3-compatible nodes. The value indicates whether the state is INCLUDE or EXCLUDE.

rcIgmpRouterSrcListTable

1.3.6.1.4.1.2272.1.30.25

not-accessible

The (conceptual) table listing the Source List entries corresponding to each interface and multicast group pair on a Router.

rcIgmpRouterSrcListEntry

1.3.6.1.4.1.2272.1.30.25.1

not-accessible

An entry (conceptual row) representing an Igmp Source.

IP rcIgmpRouterSrcListGroupAddress

1.3.6.1.4.1.2272.1.30.25.1.1

IpAddress

not-accessible

The IP multicast group address for which this entry contains information.

NUM rcIgmpRouterSrcListIfIndex

1.3.6.1.4.1.2272.1.30.25.1.2

InterfaceIndex

not-accessible

The interface for which this entry contains information for an IP multicast group address.

INT rcIgmpRouterSrcListInPort

1.3.6.1.4.1.2272.1.30.25.1.3

INTEGER

not-accessible

An unique value to identify a physical interface or a logical interface (VLAN), which has received Group reports for this source.

IP rcIgmpRouterSrcListHostAddress

1.3.6.1.4.1.2272.1.30.25.1.4

IpAddress

not-accessible

The host address to which this entry corresponds.

IP rcIgmpRouterSrcListMemberAddress

1.3.6.1.4.1.2272.1.30.25.1.5

IpAddress

not-accessible

IP Address of a member that has sent source specific report wishing to join this source.

I32 rcIgmpRouterSrcListExpire

1.3.6.1.4.1.2272.1.30.25.1.6

Integer32

read-only

This value indicates the relevance of the SrcList entry, whereby a non-zero value indicates this is an INCLUDE state value, and a zero value indicates this to be an EXCLUDE state value.

INT rcIgmpRouterSrcListMode

1.3.6.1.4.1.2272.1.30.25.1.7

INTEGER

read-only

The current member state, applicable to IGMPv3-compatible nodes. The value indicates whether the state is INCLUDE or EXCLUDE.

I32 rcIgmpRouterSrcListMemberExpire

1.3.6.1.4.1.2272.1.30.25.1.8

Integer32

read-only

This value indicates the time until the member for this source will expire

rcIgmpNewSsmTable

1.3.6.1.4.1.2272.1.30.26

not-accessible

rcIgmpNewSsmEntry

1.3.6.1.4.1.2272.1.30.26.1

not-accessible

IP rcIgmpNewSsmIpMulticastGrp

1.3.6.1.4.1.2272.1.30.26.1.1

IpAddress

not-accessible

This is the IP multicast group address that has default range of 232/8. This parameter should be configured by the user.

IP rcIgmpNewSsmIpSource

1.3.6.1.4.1.2272.1.30.26.1.2

IpAddress

not-accessible

This is the Source's IP address that will be sending traffic to the group source. This parameter should be configured by the user.

INT rcIgmpNewSsmLearningMode

1.3.6.1.4.1.2272.1.30.26.1.3

INTEGER

read-only

This is a read only field that provides information if the entry is statically configured entry (Static) or a dynamically learned entry from IGMPv3 (Dynamic). Note that Dynamic may not be used in the first step of the implementation.

T/F rcIgmpNewSsmActivity

1.3.6.1.4.1.2272.1.30.26.1.4

TruthValue

read-only

This is a read only field. It provides the activity on the corresponding (S,G). If the source is active and traffic is flowing to the switch, this field value should be Active, otherwise it should say non-active. This information is useful in knowing if the group has an active source or not when the group is joined by a member on the switch.

ENA rcIgmpNewSsmAdminState

1.3.6.1.4.1.2272.1.30.26.1.5

EnableValue

read-create

The admin state provides information on whether the entry is to be used or not. If the value of this field is Enabled (default), then the entry can be used. If the state is Disabled, then the entry will not be used, but will be saved for future use.

ROW rcIgmpNewSsmRowStatus

1.3.6.1.4.1.2272.1.30.26.1.6

RowStatus

read-create

Used to create/delete entries.

rcUserSetTime

1.3.6.1.4.1.2272.1.31

INT rcUserSetTimeYear

1.3.6.1.4.1.2272.1.31.1

INTEGER

read-write

Year of the time.

INT rcUserSetTimeMonth

1.3.6.1.4.1.2272.1.31.2

INTEGER

read-write

Month of the time.

INT rcUserSetTimeDate

1.3.6.1.4.1.2272.1.31.3

INTEGER

read-write

Date of the time.

INT rcUserSetTimeHour

1.3.6.1.4.1.2272.1.31.4

INTEGER

read-write

Hour of the time.

INT rcUserSetTimeMinute

1.3.6.1.4.1.2272.1.31.5

INTEGER

read-write

Minute of the time.

INT rcUserSetTimeSecond

1.3.6.1.4.1.2272.1.31.6

INTEGER

read-write

Second of the time.

INT rcUserSetTimeTimezone

1.3.6.1.4.1.2272.1.31.7

INTEGER

read-write

Timezone values. Since + is not a valid character inside enum declaration, E(ast) and W(est) are used to indicate + and - respectively. For example, etc-GMTE1 indicates Etc-GMT+1 and etc-GMTW1 indicates Etc-GMT-1.

rcL2Redundancy

1.3.6.1.4.1.2272.1.32

INT rcL2RedundancyHaCpuState

1.3.6.1.4.1.2272.1.32.1

INTEGER

read-only

Indicate the Ha-CPU state. initialization - indicate the CPU is in this state. oneWayActive - Modules that need to be synchronized have registered with the framework (either locally or a message was received from remote CPU (1). twoWayActive - Modules that need to be synchronized have registered with the framework (either locally or a message was received from remote CPU (2). synchronized - Table based synchroniztion was completed on the current CPU (3). remoteIncompatible - CPUs framework version is incompatible with the remote CPU (4). error - If an invalid event is generated in a given state the CPU enters Error state (5). disabled - High Availability is not enabled (6). peerNotConnected - no peer connection is established (7). peerConnected - peer connection is established (8). lostPeerConnection - lost connection to peer/Standby CPU (9). notSynchronized - Table Sync is not complete (10). synchronizeInProgress - Table Sync is in progress (11).

INT rcL2RedundancyHaEvent

1.3.6.1.4.1.2272.1.32.2

INTEGER

read-only

Indicate the Ha event status. restart (0) - Causes the state machine to restart systemRegistrationDone (1)- Causes the CPU to transfer to One Way or Two Way Active state. Locally or message received from remote CPU. tableSynchronizationDone (2) - Causes the CPU to transfer to Synchronized state. versionIncompatible (3) - Causes the CPU to go to Remote Incompatible state noEvent (4) - Means no event has occured uptill now.

ENA rcL2RedundancyEnable

1.3.6.1.4.1.2272.1.32.3

EnableValue

read-write

Indicate the feature enable/disable.

INT rcL2RedundancyStandbyCpu

1.3.6.1.4.1.2272.1.32.4

INTEGER

read-only

Indicate if the L2 Redundancy is enabled on the standby CPU.

rcNtp

1.3.6.1.4.1.2272.1.33

rcNtpGlobal

1.3.6.1.4.1.2272.1.33.1

T/F rcNtpGlobalEnable

1.3.6.1.4.1.2272.1.33.1.1

TruthValue

read-write

Enable/disable NTP feature

INT rcNtpGlobalInterval

1.3.6.1.4.1.2272.1.33.1.2

INTEGER

read-write

Time interval between successive NTP updates in minutes.

rcNtpServerTable

1.3.6.1.4.1.2272.1.33.2

not-accessible

The NTP server table. This table lists the information of a NTP server

rcNtpServerEntry

1.3.6.1.4.1.2272.1.33.2.1

not-accessible

A NTP server table entry.

IP rcNtpServerAddress

1.3.6.1.4.1.2272.1.33.2.1.1

IpAddress

read-only

Server IP address of NTP time source referred to in this table entry.

T/F rcNtpServerEnable

1.3.6.1.4.1.2272.1.33.2.1.2

TruthValue

read-write

Enable or disable this server for participation in time update.

T/F rcNtpServerAuthentication

1.3.6.1.4.1.2272.1.33.2.1.3

TruthValue

read-write

Enable or disable the MD5 Authentication on this serve.

INT rcNtpServerKeyId

1.3.6.1.4.1.2272.1.33.2.1.4

INTEGER

read-write

Public Key used to generate MD5 digest for this server.

C32 rcNtpServerAccessAttempts

1.3.6.1.4.1.2272.1.33.2.1.5

Counter32

read-only

The number of NTP requests sent to this server

C32 rcNtpServerAccessSuccess

1.3.6.1.4.1.2272.1.33.2.1.6

Counter32

read-only

The number of times this server was selected to update the time

C32 rcNtpServerAccessFailure

1.3.6.1.4.1.2272.1.33.2.1.7

Counter32

read-only

The number of times this server was rejected from updating the time

ROW rcNtpServerRowStatus

1.3.6.1.4.1.2272.1.33.2.1.8

RowStatus

read-write

Used to create/delete entries.

STR rcNtpServerStratum

1.3.6.1.4.1.2272.1.33.2.1.9

DisplayString

read-only

Stratum of this server

STR rcNtpServerVersion

1.3.6.1.4.1.2272.1.33.2.1.10

DisplayString

read-only

NTP version of this server

STR rcNtpServerRootDelay

1.3.6.1.4.1.2272.1.33.2.1.11

DisplayString

read-only

Root Delay of this server

STR rcNtpServerPrecision

1.3.6.1.4.1.2272.1.33.2.1.12

DisplayString

read-only

NTP precision of this server in seconds

STR rcNtpServerReachable

1.3.6.1.4.1.2272.1.33.2.1.13

DisplayString

read-only

NTP Reachability of this server

STR rcNtpServerSynchronized

1.3.6.1.4.1.2272.1.33.2.1.14

DisplayString

read-only

Status of synchronization with this server

rcNtpKeyTable

1.3.6.1.4.1.2272.1.33.3

not-accessible

The NTP key table. This table lists the private key of the public key Id

rcNtpKeyEntry

1.3.6.1.4.1.2272.1.33.3.1

not-accessible

A NTP key table entry.

INT rcNtpKeyId

1.3.6.1.4.1.2272.1.33.3.1.1

INTEGER

read-only

Public Key used to generate MD5 digest

STR rcNtpKeySecret

1.3.6.1.4.1.2272.1.33.3.1.2

DisplayString

read-write

Private Key used to generate MD5 Digest

ROW rcNtpKeyRowStatus

1.3.6.1.4.1.2272.1.33.3.1.3

RowStatus

read-write

Used to create/delete entries.

rcSsh

1.3.6.1.4.1.2272.1.34

rcSshGlobal

1.3.6.1.4.1.2272.1.34.1

INT rcSshGlobalVersion

1.3.6.1.4.1.2272.1.34.1.1

INTEGER

read-write

SSH version

I32 rcSshGlobalPort

1.3.6.1.4.1.2272.1.34.1.2

Integer32

read-write

SSH connection port.

INT rcSshGlobalMaxSession

1.3.6.1.4.1.2272.1.34.1.3

INTEGER

read-write

Number of session allowed.

INT rcSshGlobalTimeout

1.3.6.1.4.1.2272.1.34.1.4

INTEGER

read-write

SSH connection timeout in seconds.

INT rcSshGlobalRsaKeySize

1.3.6.1.4.1.2272.1.34.1.5

INTEGER

read-write

SSH Rsa key size.

INT rcSshGlobalDsaKeySize

1.3.6.1.4.1.2272.1.34.1.6

INTEGER

read-write

SSH Dsa key size.

T/F rcSshGlobalRsaAuth

1.3.6.1.4.1.2272.1.34.1.7

TruthValue

read-write

Enable/disable SSH RSA authentication

T/F rcSshGlobalDsaAuth

1.3.6.1.4.1.2272.1.34.1.8

TruthValue

read-write

Enable/disable SSH DSA authentication

T/F rcSshGlobalPassAuth

1.3.6.1.4.1.2272.1.34.1.9

TruthValue

read-write

Enable/disable SSH RSA authentication

INT rcSshGlobalKeyAction

1.3.6.1.4.1.2272.1.34.1.10

INTEGER

read-write

SSH key action.

INT rcSshGlobalEnable

1.3.6.1.4.1.2272.1.34.1.11

INTEGER

read-write

Enable/disable, or securely enable SSH. Securely enable turns off other daemon flag, and it takes ffect afte reboot

IP rcSshGlobalHostIpAddr

1.3.6.1.4.1.2272.1.34.1.12

IpAddress

read-write

current remote ip addr

rcSslMipTable

1.3.6.1.4.1.2272.1.34.2

not-accessible

This table would display the MIP of the SSL blade according to the slot number.

rcSslMipTableEntry

1.3.6.1.4.1.2272.1.34.2.1

not-accessible

This table get the MIP of the SSL blade on which the blade is in different cluster.

I32 rcSslMipSlot

1.3.6.1.4.1.2272.1.34.2.1.1

Integer32

read-only

Used as an index to find out the MIP of SSL blade.

STR rcSslMipMip

1.3.6.1.4.1.2272.1.34.2.1.2

DisplayString

read-only

Master IP of the SSL blade.

rcSvlan

1.3.6.1.4.1.2272.1.35

rcTengEnet

1.3.6.1.4.1.2272.1.50

rcTengEnetStats

1.3.6.1.4.1.2272.1.50.1

rcTengDot3StatsTable

1.3.6.1.4.1.2272.1.50.1.1

not-accessible

Statistics for a collection of ethernet-like interfaces attached to a particular system.

rcTengDot3StatsEntry

1.3.6.1.4.1.2272.1.50.1.1.1

not-accessible

Statistics for a particular interface to an ethernet-like medium.

I32 rcTengDot3StatsIndex

1.3.6.1.4.1.2272.1.50.1.1.1.1

Integer32

read-only

An index value that uniquely identifies an interface to an ethernet-like medium. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

C64 rcTengDot3StatsAlignmentErrors

1.3.6.1.4.1.2272.1.50.1.1.1.2

Counter64

read-only

A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.

C64 rcTengDot3StatsFCSErrors

1.3.6.1.4.1.2272.1.50.1.1.1.3

Counter64

read-only

A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.

C64 rcTengDot3StatsSingleCollisionFrames

1.3.6.1.4.1.2272.1.50.1.1.1.4

Counter64

read-only

A count of successfully transmitted frames on a particular interface for which transmission is inhibited by exactly one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsMultipleCollisionFrames object.

C64 rcTengDot3StatsMultipleCollisionFrames

1.3.6.1.4.1.2272.1.50.1.1.1.5

Counter64

read-only

A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object.

C64 rcTengDot3StatsSQETestErrors

1.3.6.1.4.1.2272.1.50.1.1.1.6

Counter64

read-only

A count of times that the SQE TEST ERROR message is generated by the PLS sublayer for a particular interface. The SQE TEST ERROR message is defined in section 7.2.2.2.4 of ANSI/IEEE 802.3-1985 and its generation is described in section 7.2.4.6 of the same document.

C64 rcTengDot3StatsDeferredTransmissions

1.3.6.1.4.1.2272.1.50.1.1.1.7

Counter64

read-only

A count of frames for which the first transmission attempt on a particular interface is delayed because the medium is busy. The count represented by an instance of this object does not include frames involved in collisions.

C64 rcTengDot3StatsLateCollisions

1.3.6.1.4.1.2272.1.50.1.1.1.8

Counter64

read-only

The number of times that a collision is detected on a particular interface later than 512 bit-times into the transmission of a packet. Five hundred and twelve bit-times corresponds to 51.2 microseconds on a 10 Mbit/s system. A (late) collision included in a count represented by an instance of this object is also considered as a (generic) collision for purposes of other collision-related statistics.

C64 rcTengDot3StatsExcessiveCollisions

1.3.6.1.4.1.2272.1.50.1.1.1.9

Counter64

read-only

A count of frames for which transmission on a particular interface fails due to excessive collisions.

C64 rcTengDot3StatsInternalMacTransmitErrors

1.3.6.1.4.1.2272.1.50.1.1.1.10

Counter64

read-only

A count of frames for which transmission on a particular interface fails due to an internal MAC sublayer transmit error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the rcTengDot3StatsLateCollisions object, the rcTengDot3StatsExcessiveCollisions object, or the rcTengDot3StatsCarrierSenseErrors object. The precise meaning of the count represented by an instance of this object is implementation- specific. In particular, an instance of this object may represent a count of transmission errors on a particular interface that are not otherwise counted.

C64 rcTengDot3StatsCarrierSenseErrors

1.3.6.1.4.1.2272.1.50.1.1.1.11

Counter64

read-only

The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame on a particular interface. The count represented by an instance of this object is incremented at most once per transmission attempt, even if the carrier sense condition fluctuates during a transmission attempt.

C64 rcTengDot3StatsFrameTooLongs

1.3.6.1.4.1.2272.1.50.1.1.1.13

Counter64

read-only

A count of frames received on a particular interface that exceed the maximum permitted frame size. The count represented by an instance of this object is incremented when the frameTooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.

C64 rcTengDot3StatsInternalMacReceiveErrors

1.3.6.1.4.1.2272.1.50.1.1.1.16

Counter64

read-only

A count of frames for which reception on a particular interface fails due to an internal MAC sublayer receive error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the rcTengDot3StatsFrameTooLongs object, the rcTengDot3StatsAlignmentErrors object, or the rcTengDot3StatsFCSErrors object. The precise meaning of the count represented by an instance of this object is implementation- specific. In particular, an instance of this object may represent a count of receive errors on a particular interface that are not otherwise counted.

OID rcTengDot3StatsEtherChipSet

1.3.6.1.4.1.2272.1.50.1.1.1.17

OBJECT IDENTIFIER

read-only

This object contains an OBJECT IDENTIFIER which identifies the chipset used to realize the interface. Ethernet-like interfaces are typically built out of several different chips. The MIB implementor is presented with a decision of which chip to identify via this object. The implementor should identify the chip which is usually called the Medium Access Control chip. If no such chip is easily identifiable, the implementor should identify the chip which actually gathers the transmit and receive statistics and error indications. This would allow a manager station to correlate the statistics and the chip generating them, giving it the ability to take into account any known anomalies in the chip.

C32 rcTengDot3StatsLinkFailures

1.3.6.1.4.1.2272.1.50.1.1.1.18

Counter32

read-only

The total number of link failures enCounter32ed on this interface.

C32 rcTengDot3StatsPacketErrors

1.3.6.1.4.1.2272.1.50.1.1.1.19

Counter32

read-only

The total number of packet errors enCounter32ed on this interface.

C32 rcTengDot3StatsCarrierErrors

1.3.6.1.4.1.2272.1.50.1.1.1.20

Counter32

read-only

The total number of carrier errors enCounter32ed on this interface.

C32 rcTengDot3StatsLinkInactiveErrors

1.3.6.1.4.1.2272.1.50.1.1.1.21

Counter32

read-only

The total number of link inactive errors enCounter32ed on this interface.

C64 rcTengDot3StatsInFlowCtrlPkts

1.3.6.1.4.1.2272.1.50.1.1.1.22

Counter64

read-only

The total number of flow control packets received by this interface.

C64 rcTengDot3StatsOutFlowCtrlPkts

1.3.6.1.4.1.2272.1.50.1.1.1.23

Counter64

read-only

The total number of flow control packets transmitted by this interface.

C64 rcTengDot3StatsFrameTooShorts

1.3.6.1.4.1.2272.1.50.1.1.1.24

Counter64

read-only

The total number of frames that are too short that were enCounter32ed on this interface.

C64 rcTengDot3StatsInPfcPkts

1.3.6.1.4.1.2272.1.50.1.1.1.26

Counter64

read-only

The total number of Priority Flow Control (PFC) packets received by this interface.

C64 rcTengDot3StatsOutPfcPkts

1.3.6.1.4.1.2272.1.50.1.1.1.27

Counter64

read-only

The total number of Priority Flow Control (PFC) packets transmitted by this interface.

rcTengStatTable

1.3.6.1.4.1.2272.1.50.1.2

not-accessible

A table used to store port statistics.

rcTengStatEntry

1.3.6.1.4.1.2272.1.50.1.2.1

not-accessible

interface Counter32s

I32 rcTengStatIndex

1.3.6.1.4.1.2272.1.50.1.2.1.1

Integer32

read-only

An index value that uniquely identifies a port. This value is similar to ifIndex in MIB2.

C32 rcTengStatBridgeInUnicastFrames

1.3.6.1.4.1.2272.1.50.1.2.1.2

Counter32

read-only

The total number of incoming unicast frames that were bridged.

C32 rcTengStatBridgeInMulticastFrames

1.3.6.1.4.1.2272.1.50.1.2.1.3

Counter32

read-only

The total number of incoming multicast frames that were bridged.

C32 rcTengStatBridgeInBroadcastFrames

1.3.6.1.4.1.2272.1.50.1.2.1.4

Counter32

read-only

The total number of incoming broadcast frames that were bridged.

C32 rcTengStatBridgeInDiscards

1.3.6.1.4.1.2272.1.50.1.2.1.5

Counter32

read-only

The total number of frames that were discarded by the bridging entity.

C32 rcTengStatBridgeOutUnicastFrames

1.3.6.1.4.1.2272.1.50.1.2.1.6

Counter32

read-only

The total number of outgoing unicast frames that were bridged.

C32 rcTengStatBridgeOutMulticastFrames

1.3.6.1.4.1.2272.1.50.1.2.1.7

Counter32

read-only

The total number of outgoing multicast frames that were bridged.

C32 rcTengStatBridgeOutBroadcastFrames

1.3.6.1.4.1.2272.1.50.1.2.1.8

Counter32

read-only

The total number of outgoing broadcast frames that were bridged.

C32 rcTengStatRouteInUnicastFrames

1.3.6.1.4.1.2272.1.50.1.2.1.9

Counter32

read-only

The total number of incoming unicast frames that were routed.

C32 rcTengStatRouteInMulticastFrames

1.3.6.1.4.1.2272.1.50.1.2.1.10

Counter32

read-only

The total number of incoming multicast frames that were routed.

C32 rcTengStatRouteInDiscards

1.3.6.1.4.1.2272.1.50.1.2.1.11

Counter32

read-only

The total number of frames that were discarded by the routing entity.

C32 rcTengStatRouteOutUnicastFrames

1.3.6.1.4.1.2272.1.50.1.2.1.12

Counter32

read-only

The total number of outgoing unicast frames that were routed.

C32 rcTengStatRouteOutMulticastFrames

1.3.6.1.4.1.2272.1.50.1.2.1.13

Counter32

read-only

The total number of outgoing multicast frames that were routed.

C32 rcTengStatStgForwardTransitions

1.3.6.1.4.1.2272.1.50.1.2.1.14

Counter32

read-only

The number of times this port has transitioned from the Learning state to the Forwarding state.

C32 rcTengStatStgInConfigBpdus

1.3.6.1.4.1.2272.1.50.1.2.1.15

Counter32

read-only

C32 rcTengStatStgInTcnBpdus

1.3.6.1.4.1.2272.1.50.1.2.1.16

Counter32

read-only

C32 rcTengStatStgInBadBpdus

1.3.6.1.4.1.2272.1.50.1.2.1.17

Counter32

read-only

C32 rcTengStatStgOutConfigBpdus

1.3.6.1.4.1.2272.1.50.1.2.1.18

Counter32

read-only

C32 rcTengStatStgOutTcnBpdus

1.3.6.1.4.1.2272.1.50.1.2.1.19

Counter32

read-only

C32 rcTengStatBridgeOutFrames

1.3.6.1.4.1.2272.1.50.1.2.1.20

Counter32

read-only

Used by the Accelar 8000 product family to account for all transmitted bridge unicast, broadcast, and multicast packets. The individual Counter32s are not supported.

rcTengIfTable

1.3.6.1.4.1.2272.1.50.1.3

not-accessible

A list of interface entries. The number of entries is given by the value of engIfNumber.

rcTengIfEntry

1.3.6.1.4.1.2272.1.50.1.3.1

not-accessible

An entry containing management information applicable to a particular interface.

NUM rcTengIfIndex

1.3.6.1.4.1.2272.1.50.1.3.1.1

InterfaceIndex

read-only

A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.

STR rcTengIfDescr

1.3.6.1.4.1.2272.1.50.1.3.1.2

DisplayString

read-only

A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.

INT rcTengIfType

1.3.6.1.4.1.2272.1.50.1.3.1.3

INTEGER

read-only

The type of interface. Additional values for IfType are assigned by the Internet Assigned Numbers Authority (IANA), through updating the syntax of the IANAifType textual convention.

I32 rcTengIfMtu

1.3.6.1.4.1.2272.1.50.1.3.1.4

Integer32

read-only

The size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface.

G32 rcTengIfSpeed

1.3.6.1.4.1.2272.1.50.1.3.1.5

Gauge32

read-only

An estimate of the interface's current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. If the bandwidth of the interface is greater than the maximum value reportable by this object then this object should report its maximum value (4,294,967,295) and ifHighSpeed must be used to report the interace's speed. For a sub-layer which has no concept of bandwidth, this object should be zero.

PHY rcTengIfPhysAddress

1.3.6.1.4.1.2272.1.50.1.3.1.6

PhysAddress

read-only

The interface's address at its protocol sub-layer. The interface's media-specific MIB must define the bit and byte ordering and format of the value contained by this object. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length.

INT rcTengIfAdminStatus

1.3.6.1.4.1.2272.1.50.1.3.1.7

INTEGER

read-write

The desired state of the interface. The testing(3) state indicates that no operational packets can be passed. When a managed system initializes, all interfaces start with IfAdminStatus in the down(2) state. As a result of either explicit management action or per configuration information retained by the managed system, IfAdminStatus is then changed to either the up(1) or testing(3) states (or remains in the down(2) state).

INT rcTengIfOperStatus

1.3.6.1.4.1.2272.1.50.1.3.1.8

INTEGER

read-only

The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. If IfAdminStatus is down(2) then IfOperStatus should be down(2). If IfAdminStatus is changed to up(1) then ifOperStatus should change to up(1) if the interface is ready to transmit and receive network traffic; it should change to dormant(5) if the interface is waiting for external actions (such as a serial line waiting for an incomming connection); it should remain in the down(2) state if and only if there is a fault that prevents if from going to the up(1) state.

TIK rcTengIfLastChange

1.3.6.1.4.1.2272.1.50.1.3.1.9

TimeTicks

read-only

The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.

C64 rcTengIfInOctets

1.3.6.1.4.1.2272.1.50.1.3.1.10

Counter64

read-only

The total number of octets received on the interface, including framing characters.

C64 rcTengIfInUcastPkts

1.3.6.1.4.1.2272.1.50.1.3.1.11

Counter64

read-only

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer.

C64 rcTengIfInDiscards

1.3.6.1.4.1.2272.1.50.1.3.1.13

Counter64

read-only

The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.

C64 rcTengIfInErrors

1.3.6.1.4.1.2272.1.50.1.3.1.14

Counter64

read-only

For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol.

C64 rcTengIfInUnknownProtos

1.3.6.1.4.1.2272.1.50.1.3.1.15

Counter64

read-only

For packet-oriented interfaces, the number of packets received via the interface which were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces which support protocol multiplexing the number of transmission units received via the interface which were discarded because of an unknown or unsupported protocol. For any interface which does not support protocol multiplexing, this counter will always be 0.

C64 rcTengIfOutOctets

1.3.6.1.4.1.2272.1.50.1.3.1.16

Counter64

read-only

The total number of octets transmitted out of the interface, including framing characters.

C64 rcTengIfOutUcastPkts

1.3.6.1.4.1.2272.1.50.1.3.1.17

Counter64

read-only

The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent.

C64 rcTengIfOutDiscards

1.3.6.1.4.1.2272.1.50.1.3.1.19

Counter64

read-only

The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.

C64 rcTengIfOutErrors

1.3.6.1.4.1.2272.1.50.1.3.1.20

Counter64

read-only

For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors.

rcTengIfXTable

1.3.6.1.4.1.2272.1.50.1.4

not-accessible

A list of interface entries. The number of entries is given by the value of ifNumber. This table contains additional objects for the interface table.

rcTengIfXEntry

1.3.6.1.4.1.2272.1.50.1.4.1

not-accessible

An entry containing additional management information applicable to a particular interface.

NUM rcTengIfXIndex

1.3.6.1.4.1.2272.1.50.1.4.1.1

InterfaceIndex

read-only

A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.

STR rcTengIfName

1.3.6.1.4.1.2272.1.50.1.4.1.2

DisplayString

read-only

The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's `console'. This might be a text name, such as `le0' or a simple port number, such as `1', depending on the interface naming syntax of the device. If several entries in the rcTengIfTable together represent a single interface as named by the device, then each will have the same value of rcTengIfName. If there is no local name, or this object is otherwise not applicable, then this object contains a 0-length string.

C64 rcTengIfInMulticastPkts

1.3.6.1.4.1.2272.1.50.1.4.1.3

Counter64

read-only

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses.

C64 rcTengIfInBroadcastPkts

1.3.6.1.4.1.2272.1.50.1.4.1.4

Counter64

read-only

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer.

C64 rcTengIfOutMulticastPkts

1.3.6.1.4.1.2272.1.50.1.4.1.5

Counter64

read-only

The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses.

C64 rcTengIfOutBroadcastPkts

1.3.6.1.4.1.2272.1.50.1.4.1.6

Counter64

read-only

The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent.

C64 rcTengIfHCInOctets

1.3.6.1.4.1.2272.1.50.1.4.1.7

Counter64

read-only

The total number of octets received on the interface, including framing characters. This object is a 64-bit version of rcTengIfInOctets.

C64 rcTengIfHCInUcastPkts

1.3.6.1.4.1.2272.1.50.1.4.1.8

Counter64

read-only

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. This object is a 64-bit version of rcTengIfInUcastPkts.

C64 rcTengIfHCInMulticastPkts

1.3.6.1.4.1.2272.1.50.1.4.1.9

Counter64

read-only

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses. This object is a 64-bit version of rcTengIfInMulticastPkts.

C64 rcTengIfHCInBroadcastPkts

1.3.6.1.4.1.2272.1.50.1.4.1.10

Counter64

read-only

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. This object is a 64-bit version of IfInBroadcastPkts.

C64 rcTengIfHCOutOctets

1.3.6.1.4.1.2272.1.50.1.4.1.11

Counter64

read-only

The total number of octets transmitted out of the interface, including framing characters. This object is a 64-bit version of rcTengIfOutOctets.

C64 rcTengIfHCOutUcastPkts

1.3.6.1.4.1.2272.1.50.1.4.1.12

Counter64

read-only

The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. This object is a 64-bit version of rcTengIfOutUcastPkts.

C64 rcTengIfHCOutMulticastPkts

1.3.6.1.4.1.2272.1.50.1.4.1.13

Counter64

read-only

The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. This object is a 64-bit version of rcTengIfOutMulticastPkts.

C64 rcTengIfHCOutBroadcastPkts

1.3.6.1.4.1.2272.1.50.1.4.1.14

Counter64

read-only

The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent. This object is a 64-bit version of rcTengIfOutBroadcastPkts.

INT rcTengIfLinkUpDownTrapEnable

1.3.6.1.4.1.2272.1.50.1.4.1.15

INTEGER

read-write

Indicates whether linkUp/linkDown traps should be generated for this interface. By default, this object should have the value enabled(1) for interfaces which do not operate on 'top' of any other interface (as defined in the rcTengIfStackTable), and disabled(2) otherwise.

G32 rcTengIfHighSpeed

1.3.6.1.4.1.2272.1.50.1.4.1.16

Gauge32

read-only

An estimate of the interface's current bandwidth in units of 1,000,000 bits per second. If this object reports a value of `n' then the speed of the interface is somewhere in the range of `n-500,000' to `n+499,999'. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. For a sub-layer which has no concept of bandwidth, this object should be zero.

T/F rcTengIfPromiscuousMode

1.3.6.1.4.1.2272.1.50.1.4.1.17

TruthValue

read-write

This object has a value of false(2) If this interface only accepts packets/frames that are addressed to this station. This object has a value of true(1) when the station accepts all packets/frames transmitted on the media. The value true(1) is only legal on certain types of media. If legal, setting this object to a value of true(1) may require the interface to be reset before becoming effective. The value of rcTengIfPromiscuousMode does not affect the reception of broadcast and multicast packets/frames by the interface.

T/F rcTengIfConnectorPresent

1.3.6.1.4.1.2272.1.50.1.4.1.18

TruthValue

read-only

This object has the value 'true(1)' if the interface sublayer has a physical connector and the value 'false(2)' otherwise.

rcWisTrap

1.3.6.1.4.1.2272.1.50.2

INT rcWisSonetTrapType

1.3.6.1.4.1.2272.1.50.2.1

INTEGER

read-only

Used to indicate a particular type of 10GE Sonet trap.

INT rcWisSonetTrapIndication

1.3.6.1.4.1.2272.1.50.2.2

INTEGER

read-only

Used to indicate an indication for a 10GE Sonet trap.

rcRec

1.3.6.1.4.1.2272.1.51

rcRecReservTable

1.3.6.1.4.1.2272.1.51.1

not-accessible

This table would display the statistics of several HW record type used. This will also let the user reserve certain number of records for each type.

rcRecReservTablEntry

1.3.6.1.4.1.2272.1.51.1.1

not-accessible

INT rcRecReservRecordType

1.3.6.1.4.1.2272.1.51.1.1.1

INTEGER

read-only

.

I32 rcRecReservUsed

1.3.6.1.4.1.2272.1.51.1.1.2

Integer32

read-only

Displayes the number of HW records actually usee by the recordType.

I32 rcRecReservReserved

1.3.6.1.4.1.2272.1.51.1.1.3

Integer32

read-only

Displayes the number of HW records reserved for the recordType.

I32 rcRecReservNewReserved

1.3.6.1.4.1.2272.1.51.1.1.4

Integer32

read-write

Displayes the number of HW records that w ill be reserved for this recordType after reset if the configuration is saved.

I32 rcRecReservDefReserved

1.3.6.1.4.1.2272.1.51.1.1.5

Integer32

read-only

Number of records reserved for this recordType if loaded with factory default.

rcLacp

1.3.6.1.4.1.2272.1.53

rcLacpGlobal

1.3.6.1.4.1.2272.1.53.1

T/F rcLacpGlobalEnable

1.3.6.1.4.1.2272.1.53.1.1

TruthValue

read-write

globally enable/disable LACP

I32 rcLacpGlobalSystemPriority

1.3.6.1.4.1.2272.1.53.1.2

Integer32

read-write

set system priority to all the LACP enabled aggregators and prots

INT rcLacpGlobalFastPeriodicTime

1.3.6.1.4.1.2272.1.53.1.3

INTEGER

read-write

The number of miliseconds between periodic transmissions using Short Timeouts. Set this value to all LACP enabled ports.

INT rcLacpGlobalSlowPeriodicTime

1.3.6.1.4.1.2272.1.53.1.4

INTEGER

read-write

The number of miliseconds between periodic transmissions using LONG Timeouts. Set this value to all LACP enabled ports.

INT rcLacpGlobalTimeoutScale

1.3.6.1.4.1.2272.1.53.1.5

INTEGER

read-write

Scalar value used to calculate timeout time from periodic time. Set this value to all LACP enabled ports.

INT rcLacpGlobalAggrWaitTime

1.3.6.1.4.1.2272.1.53.1.6

INTEGER

read-write

The number of mili seconds to delay aggregation to allow multiple links to aggregate simultaneously.

T/F rcLacpGlobalVlacpEnable

1.3.6.1.4.1.2272.1.53.1.7

TruthValue

read-write

globally enable/disable Virtual LACP

INT rcLacpGlobalFastPeriodicTimeOper

1.3.6.1.4.1.2272.1.53.1.9

INTEGER

read-only

The operating value of global fast periodic timer.

INT rcLacpGlobalSlowPeriodicTimeOper

1.3.6.1.4.1.2272.1.53.1.10

INTEGER

read-only

The operating value of global show periodic time.

INT rcLacpGlobalTimeoutScaleOper

1.3.6.1.4.1.2272.1.53.1.11

INTEGER

read-only

The operating value of global timeout scale.

INT rcLacpGlobalAggrWaitTimeOper

1.3.6.1.4.1.2272.1.53.1.12

INTEGER

read-only

The operating value of global aggregate wait time.

MAC rcLacpGlobalSmltSysId

1.3.6.1.4.1.2272.1.53.1.13

MacAddress

read-write

LACP system ID for SMLT

rcLicense

1.3.6.1.4.1.2272.1.56

INT rcLicenseNumber

1.3.6.1.4.1.2272.1.56.1

INTEGER

read-only

Bit position number of license bitmap

OCT rcLicenseBitMap

1.3.6.1.4.1.2272.1.56.2

OCTET STRING

read-only

License bit map. Bitmap number is defined in rcLicenseNumber

rcEap

1.3.6.1.4.1.2272.1.57

rcFdb

1.3.6.1.4.1.2272.1.60

rcGlobalMacFilterTable

1.3.6.1.4.1.2272.1.60.1

not-accessible

A list of Global Mac filter entries.

rcGlobalMacFilterEntry

1.3.6.1.4.1.2272.1.60.1.1

not-accessible

this entry is used for global mac filtering.Any Mac address configured here will be discarded globally by the switch.

MAC rcGlobalMacFilterAddress

1.3.6.1.4.1.2272.1.60.1.1.1

MacAddress

not-accessible

A MAC address which will be discarded globally by the switch

ROW rcGlobalMacFilterRowStatus

1.3.6.1.4.1.2272.1.60.1.1.2

RowStatus

read-write

Used to create/delete entries in rcGlobalMacFilterTable.

rcIpv6

1.3.6.1.4.1.2272.1.62

rcIpv6Mib

1.3.6.1.4.1.2272.1.62.1

rcIpv6Notifications

1.3.6.1.4.1.2272.1.62.1.0

rcIpv6Objects

1.3.6.1.4.1.2272.1.62.1.1

rcIpv6Scalars

1.3.6.1.4.1.2272.1.62.1.1.1

INT rcIpv6IcmpErrorInterval

1.3.6.1.4.1.2272.1.62.1.1.1.1

INTEGER

read-write

The rate (in milliseconds) at which ICMP error messages can be sent out. A value of zero means not be send any.

T/F rcIpv6IcmpNetUnreach

1.3.6.1.4.1.2272.1.62.1.1.1.3

TruthValue

read-write

Used to set icmp net unreach feature enable/ disable.

T/F rcIpv6IcmpRedirectMsg

1.3.6.1.4.1.2272.1.62.1.1.1.4

TruthValue

read-write

Used to set icmp redirect feature enable/ disable.

INT rcIpv6IcmpErrorQuota

1.3.6.1.4.1.2272.1.62.1.1.1.5

INTEGER

read-write

The number of icmp error messages that can be sent during the icmp error interval. A value of zero means not be send any.

U32 rcIpv6PrefixListTableSize

1.3.6.1.4.1.2272.1.62.1.1.1.8

Unsigned32

read-only

Size of Ipv6 Prefix List Table

T/F rcIpv6RouteStaticClear

1.3.6.1.4.1.2272.1.62.1.1.1.10

TruthValue

read-write

Clear all IPv6 static routes.

T/F rcIpv6RouteStaticGlobalAdminEnabled

1.3.6.1.4.1.2272.1.62.1.1.1.11

TruthValue

read-write

Used to globally enable/disable all IPv6 static routes.

rcIpv6InterfaceTable

1.3.6.1.4.1.2272.1.62.1.1.2

not-accessible

This table contains list of IPv6 interfaces and per-interface IPv6-specific information.

rcIpv6InterfaceEntry

1.3.6.1.4.1.2272.1.62.1.1.2.1

not-accessible

An entry of ipv6 interface In Table containing per-interface information.

NUM rcIpv6InterfaceIfIndex

1.3.6.1.4.1.2272.1.62.1.1.2.1.1

InterfaceIndex

not-accessible

An unique value to identify a physical interface or a logical interface (VLAN). For the brouter port it is the ifindex of the port and in the case of the vlan it is the ifindex of the vlan.

ADR rcIpv6InterfaceIdentifier

1.3.6.1.4.1.2272.1.62.1.1.2.1.2

Ipv6AddressIfIdentifier

read-create

IPv6 address interface identifiers. This is a binary string of up to 8 octets in network byte-order.

INT rcIpv6InterfaceIdentifierLength

1.3.6.1.4.1.2272.1.62.1.1.2.1.3

INTEGER

read-create

The length of the Interface Identifier in bits.

STR rcIpv6InterfaceDescr

1.3.6.1.4.1.2272.1.62.1.1.2.1.4

DisplayString

read-create

A textual string containing information about the interface. This string may be set by network management system.

RCV rcIpv6InterfaceVlanId

1.3.6.1.4.1.2272.1.62.1.1.2.1.5

RcVlanIdOrNone

read-create

A value that uniquely identifies the Virtual LAN associated with this entry. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag.

INT rcIpv6InterfaceType

1.3.6.1.4.1.2272.1.62.1.1.2.1.6

INTEGER

read-only

The interface type.

INT rcIpv6InterfaceReasmMaxSize

1.3.6.1.4.1.2272.1.62.1.1.2.1.7

INTEGER

read-create

MTU for this IPv6 interface, this value should be same for all the ip addresses defined on this interface. In VSP9000, Supported range for IO interface, supported range is(1280..1500 | 1850 | 9500). For Mgmt interface, Supporyed Range is (1280..1500)

PHY rcIpv6InterfacePhysAddress

1.3.6.1.4.1.2272.1.62.1.1.2.1.8

PhysAddress

read-only

The media-dependent `physical' address, for the ethernet media it is the MAC address

T/F rcIpv6InterfaceAdminStatus

1.3.6.1.4.1.2272.1.62.1.1.2.1.9

TruthValue

read-create

The indication of whether IPv6 is enabled (up) or disabled (down) on this interface. This object does not affect the state of the interface itself, only its connection to an IPv6 stack.

INT rcIpv6InterfaceOperStatus

1.3.6.1.4.1.2272.1.62.1.1.2.1.10

INTEGER

read-only

Operating status of the interface.

INT rcIpv6InterfaceReachableTime

1.3.6.1.4.1.2272.1.62.1.1.2.1.11

INTEGER

read-create

The time (in milliseconds) a neighbor is considered reachable after receiving a reachability confirmation. REFERENCE RFC2461, Section 6.3.2

INT rcIpv6InterfaceRetransmitTime

1.3.6.1.4.1.2272.1.62.1.1.2.1.12

INTEGER

read-create

Deprecated. Use rcIpv6InterfaceRetransmitTimer instead.

T/F rcIpv6InterfaceMulticastAdminStatus

1.3.6.1.4.1.2272.1.62.1.1.2.1.13

TruthValue

read-create

This indicates the admin status for multicast for this interface.

ROW rcIpv6InterfaceRowStatus

1.3.6.1.4.1.2272.1.62.1.1.2.1.14

RowStatus

read-create

Row status for create/delete.

T/F rcIpv6InterfaceDhcpEnabled

1.3.6.1.4.1.2272.1.62.1.1.2.1.15

TruthValue

read-create

Enable or disable DHCP on the specified interface.

INT rcIpv6InterfaceMacOffset

1.3.6.1.4.1.2272.1.62.1.1.2.1.16

INTEGER

read-create

Used to request a particular MAC for an IPv6 VLAN. The system has 1536 mac addresses, last 4 are reserved for MG. One can either mention a mac offset while configuring IPv6 on a vlan or it can be alloted by the system within the above range.

U32 rcIpv6InterfaceRetransmitTimer

1.3.6.1.4.1.2272.1.62.1.1.2.1.17

Unsigned32

read-create

The time (in milliseconds) between retransmissions of Neighbor Solicitation messages to a neighbor when resolving the address or when probing the reachability of a neighbor. REFERENCE RFC2461, Section 6.3.2

I32 rcIpv6InterfaceCurHopLimit

1.3.6.1.4.1.2272.1.62.1.1.2.1.18

Integer32

read-create

The default value to be placed in the current hop limit field in router advertisements sent from this interface. The value should be set to the current diameter of the Internet. The default should be set to the value specified in the IANA web pages (www.iana.org) at the time of implementation. REFERENCE RFC2461 Section 6.2.1

T/F rcIpv6InterfaceClearIcmpStats

1.3.6.1.4.1.2272.1.62.1.1.2.1.20

TruthValue

read-create

Clear ICMP statistics for an interface

T/F rcIpv6InterfaceClearGeneralStats

1.3.6.1.4.1.2272.1.62.1.1.2.1.21

TruthValue

read-create

Clear general statistics for an interface

T/F rcIpv6InterfaceClearNeighborCache

1.3.6.1.4.1.2272.1.62.1.1.2.1.22

TruthValue

read-create

Clear Neighbor Cache for an interface

T/F rcIpv6InterfaceClearDestinationCache

1.3.6.1.4.1.2272.1.62.1.1.2.1.23

TruthValue

read-create

Clear Destination Cache for an interface

T/F rcIpv6InterfaceReversePathCheckEnable

1.3.6.1.4.1.2272.1.62.1.1.2.1.24

TruthValue

read-create

Used to indicate whether this interface should perform Reverse Path Check

INT rcIpv6InterfaceReversePathCheckMode

1.3.6.1.4.1.2272.1.62.1.1.2.1.25

INTEGER

read-create

Reverse Path Checking mode.

T/F rcIpv6InterfaceForwardingEnabled

1.3.6.1.4.1.2272.1.62.1.1.2.1.26

TruthValue

read-create

Used to indicate whether this interface should perform forwarding

T/F rcIpv6InterfaceRsmltEnable

1.3.6.1.4.1.2272.1.62.1.1.2.1.27

TruthValue

read-create

Used to indicate whether this interface has rsmlt enabled or not

rcIpv6AddressTable

1.3.6.1.4.1.2272.1.62.1.1.3

not-accessible

This table contains addressing information relevant to the entity's interfaces. This table does not contain multicast address information. Tables for such information should be contained in multicast specific MIBs such as RFC3019. While this table is writable the user will note that several objects, such as rcIpv6AddressOrigin, are not. The intention in allowing a user to write to this table is to allow them to add or remove any entry that isn't permanent. The user should be allowed to modify objects and entries when that would not cause inconsistencies within the table. Allowing write access to objects such as rcIpv6AddressOrigin could allow a user to insert an entry and then label it incorrectly.

rcIpv6AddressEntry

1.3.6.1.4.1.2272.1.62.1.1.3.1

not-accessible

An address mapping for a particular interface. Note that when an address is added to an interface the resulted prefix is added to that interface.

NUM rcIpv6AddressIfIndex

1.3.6.1.4.1.2272.1.62.1.1.3.1.1

InterfaceIndex

not-accessible

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of the IfIndex field in the rcIpv6InterfaceIfIndex.

ADR rcIpv6AddressAddr

1.3.6.1.4.1.2272.1.62.1.1.3.1.2

Ipv6Address

not-accessible

The IPv6 address to which this entry's addressing information pertains. This is one of the ipv6 addresses that this interface(identified by the rcIpv6AddressIfIndex) has. Implementors need to be aware that if the size of ipAddressAddr exceeds 116 octets then OIDS of instances of columns in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c or SNMPv3.

INT rcIpv6AddressType

1.3.6.1.4.1.2272.1.62.1.1.3.1.3

INTEGER

read-write

The type of address. It is either unicast or anycast IPv6 addresses (RFC3513).

INT rcIpv6AddressPrefixLength

1.3.6.1.4.1.2272.1.62.1.1.3.1.4

INTEGER

read-write

Prefix Length value for this address. Cannot be changed after the creation. This field MUST be provided in order to create an entry in this table.

NUM rcIpv6AddressPrefix

1.3.6.1.4.1.2272.1.62.1.1.3.1.5

RowPointer

read-only

A pointer to the row in the prefix table to which this address belongs. May be { 0 0 } if there is no such row.

NUM rcIpv6AddressOrigin

1.3.6.1.4.1.2272.1.62.1.1.3.1.6

IpAddressOriginTC

read-only

The origin of the address. The origin of the address, one of: other(1),manual(2), dhcp(4),linklayer(5), random(6)

ADR rcIpv6AddressStatus

1.3.6.1.4.1.2272.1.62.1.1.3.1.7

IpAddressStatusTC

read-only

The status of the address, describing if the address can be used for communication. It will One of: preferred(1), deprecated(2),invalid(3),inaccessible(4),unknown(5), tentative(6), duplicate(7)

TIM rcIpv6AddressCreated

1.3.6.1.4.1.2272.1.62.1.1.3.1.8

TimeStamp

read-only

The value of sysUpTime at the time this entry was created. If this entry was created prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.

TIM rcIpv6AddressLastChanged

1.3.6.1.4.1.2272.1.62.1.1.3.1.9

TimeStamp

read-only

The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.

ROW rcIpv6AddressRowStatus

1.3.6.1.4.1.2272.1.62.1.1.3.1.10

RowStatus

read-create

The status of this conceptual row. The RowStatus TC requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified. The value of this object has no effect on whether other objects in this conceptual row can be modified. A conceptual row can not be made active until the rcIpv6AddressIfIndex has been set to a valid index. Only createAndGo and Delete vlaues are supported.

rcIpv6PrefixTable

1.3.6.1.4.1.2272.1.62.1.1.4

not-accessible

This table allows the user to determine the source of an IP address or set of IP addresses and allows other tables to share the information via pointer rather than by copying. For example when the node configures both a unicast and anycast address for a prefix the ipAddressPrefix objects for those addresses will point to a single row in this table. This table primarily provides support for IPv6 prefixes and several of the objects are less meaningful for IPv4. The table continues to allow IPv4 addresses to allow future flexibility. In order to promote a common configuration this document includes suggestions for default values for IPv4 prefixes. Each of these values may be overridden if an object is meaningful to the node. All prefixes used by this entity should be included in this table independent of how the entity learned the prefix. (This table isn't limited to prefixes learned from router advertisements.)

rcIpv6PrefixEntry

1.3.6.1.4.1.2272.1.62.1.1.4.1

not-accessible

An entry of ipv6 prefix In the Table.

NUM rcIpv6PrefixIfIndex

1.3.6.1.4.1.2272.1.62.1.1.4.1.1

InterfaceIndex

not-accessible

An unique value to identify an ipv6 interface. For the brouter port it is the ifindex of the port and in the case of the vlan it is the ifindex of the vlan.

ADR rcIpv6PrefixAddr

1.3.6.1.4.1.2272.1.62.1.1.4.1.2

Ipv6Address

not-accessible

Prefix to create an ipv6 address in ipv6 interface table.

INT rcIpv6PrefixLength

1.3.6.1.4.1.2272.1.62.1.1.4.1.3

INTEGER

not-accessible

Mask to create an ipv6 prefix entry either will be advertised or suppressed

RCV rcIpv6PrefixVlanId

1.3.6.1.4.1.2272.1.62.1.1.4.1.4

RcVlanIdOrNone

read-only

A value that uniquely identifies the Virtual LAN associated with this entry. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag.

INT rcIpv6PrefixUseDefaultVal

1.3.6.1.4.1.2272.1.62.1.1.4.1.5

INTEGER

read-write

Select one of the value to set/use it's value to default value. This is a bitmask field, setting all the bits means that all the options will be reverted to default values.

DAT rcIpv6PrefixAtValidLife

1.3.6.1.4.1.2272.1.62.1.1.4.1.8

DateAndTime

read-write

Is the date and time, upon reaching this value the prefix will be expired, if configured this option will be included in the neighbor advertisement for this prefix.

DAT rcIpv6PrefixAtPreferredLife

1.3.6.1.4.1.2272.1.62.1.1.4.1.9

DateAndTime

read-write

Is the date and time, upon reaching this value the prefix will be expired, if configured this option will be included in the neighbor advertisement for this prefix.

T/F rcIpv6PrefixInfinite

1.3.6.1.4.1.2272.1.62.1.1.4.1.10

TruthValue

read-write

if set the prefix's valid lifetime will not exprie.

T/F rcIpv6PrefixOnLinkFlag

1.3.6.1.4.1.2272.1.62.1.1.4.1.11

TruthValue

read-write

if set then this prefix can be used for onlink determination. This value be placed in the L-bit field in the prefix information option. It is a 1 bit flag.

T/F rcIpv6PrefixAutoFlag

1.3.6.1.4.1.2272.1.62.1.1.4.1.12

TruthValue

read-write

if set then this prefix can be used for autonomous address config. This value be placed in the auto-flag field in the prefix information option. It is a 1 bit flag.

INT rcIpv6PrefixAddressEui

1.3.6.1.4.1.2272.1.62.1.1.4.1.13

INTEGER

read-write

Use an EUI-64 interface ID in the low-order 64bits of the address when not specified in the address field. If enabled use EUI, otherwise use EUI-64 and complement U/L (Universal/Local bit). This operation should be allowed for both global and link local addresses. Once the entry is create cannot modify this field. This will be valid to use only when the PrefixLength is 64 or less

T/F rcIpv6PrefixNoAdvertise

1.3.6.1.4.1.2272.1.62.1.1.4.1.14

TruthValue

read-write

if set then this prefix can not be included in the neighbor advertisement.

ROW rcIpv6PrefixRowStatus

1.3.6.1.4.1.2272.1.62.1.1.4.1.15

RowStatus

read-create

Row status for create/delete.

U32 rcIpv6PrefixValidLifetime

1.3.6.1.4.1.2272.1.62.1.1.4.1.16

Unsigned32

read-create

Valid lifetime in seconds, indicates how long this prefix advertised in the nbr advertisement is valid. Value of 4294967295 represents infinity.

U32 rcIpv6PrefixPreferredLifetime

1.3.6.1.4.1.2272.1.62.1.1.4.1.17

Unsigned32

read-create

Preferred lifetime in seconds, indicates how long this prefix advertised in advertisemt for this prefix. Value of 4294967295 represents infinity.

rcIpv6RouterAdvertTable

1.3.6.1.4.1.2272.1.62.1.1.5

not-accessible

The table containing information used to construct router advertisements.

rcIpv6RouterAdvertEntry

1.3.6.1.4.1.2272.1.62.1.1.5.1

not-accessible

An entry containing information used to construct router advertisements.

NUM rcIpv6RouterAdvertIfIndex

1.3.6.1.4.1.2272.1.62.1.1.5.1.1

InterfaceIndex

not-accessible

An unique value to identify an ipv6 interface. For the brouter port it is the ifindex of the port and in the case of the vlan it is the ifindex of the vlan.

T/F rcIpv6RouterAdvertSendAdverts

1.3.6.1.4.1.2272.1.62.1.1.5.1.2

TruthValue

read-write

A flag indicating whether or not the router sends periodic router advertisements and responds to router solicitations on this interface. REFERENCE RFC2461 Section 6.2.1

INT rcIpv6RouterAdvertUseDefaultVal

1.3.6.1.4.1.2272.1.62.1.1.5.1.3

INTEGER

read-write

Select one of the value to set/use it's value to default value, or set all the bits to indicate all the options will be set to their default value.

INT rcIpv6RouterAdvertMaxInterval

1.3.6.1.4.1.2272.1.62.1.1.5.1.4

INTEGER

read-write

Configure the max interval (in seconds) at which the transmission of route advertisments can occur on this interface. This must be no less than 4 seconds and no greater than 1800.

INT rcIpv6RouterAdvertMinInterval

1.3.6.1.4.1.2272.1.62.1.1.5.1.5

INTEGER

read-write

Configure the min interval (in seconds) at which the transmission of route advertisments can occur on this interface. This must be no less than 3 seconds and no greater than .75* max-interval.

INT rcIpv6RouterAdvertReachableTime

1.3.6.1.4.1.2272.1.62.1.1.5.1.6

INTEGER

read-write

The value (in milliseconds) to be placed in the router advertisement message sent by the router. The value zero means unspecified (by this router). Used to configure the amount of time that a remote IPv6 node is considered reachable after some reachability confirmation event has occured. REFERENCE RFC2461 Section 6.2.1

INT rcIpv6RouterAdvertRetransmitTimer

1.3.6.1.4.1.2272.1.62.1.1.5.1.7

INTEGER

read-only

The value (in milliseconds) to be placed in the retransmit timer field in router advertisement message sent from this interface. The value zero means unspecified (by this router). Used to configure the amount of time that router should wait for the transmit to occur. REFERENCE RFC2461 Section 6.2.1 Deprecated by rcIpv6RouterAdvertRetransmitTime

INT rcIpv6RouterAdvertDefaultLifeTime

1.3.6.1.4.1.2272.1.62.1.1.5.1.8

INTEGER

read-write

The value to be placed in the router lifetime field of router advertisements sent from this interface. This value MUST be either 0 or between rcIpv6RouterAdvertMaxInterval and 9000 seconds. A value of zero indicates that the router is not to be used as a default router. The default is 3 * rcIpv6RouterAdvertMaxInterval. REFERENCE RFC2461 Section 6.2.1

INT rcIpv6RouterAdvertCurHopLimit

1.3.6.1.4.1.2272.1.62.1.1.5.1.9

INTEGER

read-write

The default value to be placed in the current hop limit field in router advertisements sent from this interface. The value should be set to the current diameter of the Internet. A value of zero in the router advertisement indicates that the advertisement isn't specifying a value for curHopLimit. The default should be set to the value specified in the IANA web pages (www.iana.org) at the time of implementation. REFERENCE RFC2461 Section 6.2.1

T/F rcIpv6RouterAdvertManagedFlag

1.3.6.1.4.1.2272.1.62.1.1.5.1.10

TruthValue

read-write

if true then the M-bit(Managed address configureation) in the router adverisement will be set. REFERENCE RFC2461 Section 6.2.1

T/F rcIpv6RouterAdvertOtherConfigFlag

1.3.6.1.4.1.2272.1.62.1.1.5.1.11

TruthValue

read-write

if true then the O-bit (Other stateful Configuration) in the router adverisement will be set. REFERENCE RFC2461 Section 6.2.1

INT rcIpv6RouterAdvertDadNsNum

1.3.6.1.4.1.2272.1.62.1.1.5.1.12

INTEGER

read-write

The number of neighbor solicitation messages for DAD (Duplicate address detection). A value 0 is used to disable DAD process on this interface. A value 1 is used to send one advertisment without any retransmissions.

U32 rcIpv6RouterAdvertLinkMTU

1.3.6.1.4.1.2272.1.62.1.1.5.1.13

Unsigned32

read-write

The value to be placed in MTU options sent by the router on this interface. A value of zero indicates that no MTU options are sent. REFERENCE RFC2461 Section 6.2.1

U32 rcIpv6RouterAdvertRetransmitTime

1.3.6.1.4.1.2272.1.62.1.1.5.1.14

Unsigned32

read-write

The value (in milliseconds) to be placed in the retransmit timer field in router advertisement message sent from this interface. The value zero means unspecified (by this router). Used to configure the amount of time that router should wait for the transmit to occur. REFERENCE RFC2461 Section 6.2.1. Use this object to replace rcIpv6RouterAdvertRetransmitTimer

rcIpv6StaticRouteTable

1.3.6.1.4.1.2272.1.62.1.1.6

not-accessible

This table contains list of routes that are created by the user to destination networks.

rcIpv6StaticRouteEntry

1.3.6.1.4.1.2272.1.62.1.1.6.1

not-accessible

An entry in the static route table for IPv6 can be created for a destination with a specific prefix length; multiple entries to the same destination are created either by specifying the next-hop or interfaceIndex or both to reach the destination. However if the nexthop Ipv6 address is a link-local address then IfIndex must be supplied.

ADR rcIpv6StaticRouteDest

1.3.6.1.4.1.2272.1.62.1.1.6.1.1

Ipv6Address

not-accessible

The destination IPv6 address of this route. The values for the index objects rcIpv6StaticRouteDest and rcIpv6StaticRoutePrefixLength must be consistent. When the value of rcIpv6StaticRouteDest (excluding the zone index, if one is present) is x, then the bitwise logical-AND of x with the value of the mask formed from the corresponding index object rcIpv6StaticRoutePrefixLength MUST be equal to x. If not, then the index pair is not consistent and an inconsistentName error must be returned on SET or CREATE requests.

INT rcIpv6StaticRoutePrefixLength

1.3.6.1.4.1.2272.1.62.1.1.6.1.2

INTEGER

not-accessible

Indicates the number of leading one bits which form the mask to be logical-ANDed with the destination address before being compared to the value in the rcIpv6StaticRouteDestAddr field.

ADR rcIpv6StaticRouteNextHop

1.3.6.1.4.1.2272.1.62.1.1.6.1.3

Ipv6Address

not-accessible

Next hop IPv6 address for this destination. On remote routes, the address of the next system en route. For non-remote routes, a zero length string.

NUM rcIpv6StaticRouteIfIndex

1.3.6.1.4.1.2272.1.62.1.1.6.1.4

InterfaceIndex

not-accessible

The ifIndex value which identifies the local interface through which the next hop of this route should be reached. A value of 0 is valid and represents the scenario where no interface is specified.

INT rcIpv6StaticRouteDistance

1.3.6.1.4.1.2272.1.62.1.1.6.1.5

INTEGER

read-write

cost/distance to reach the destination for this node.

INT rcIpv6StaticRouteStatus

1.3.6.1.4.1.2272.1.62.1.1.6.1.6

INTEGER

read-only

(1)notReachable means the route is not reachable and no neighbor request entry is built to resolved the next-hop. It happens when there is no route or neighbor to reach the static route's next-hop. (2)tryToResolve means the route is not reachable but a neighbor request entry is built to resolved the next-hop. It happens when there is a local equivelent route in system to reach the next-hop but the neighor is not learnt yet (3)reachableNotInRtm means the static route is reachable but it is not in RTM. It happens when the static route is reachable, but it is not the best among alternative static route. (4)reachableInRtm means the static route is reachable and it is in RTM. It happens when the static route is reachable, and it is the best among alternative static route to be added into RTM.

INT rcIpv6StaticRoutePreference

1.3.6.1.4.1.2272.1.62.1.1.6.1.7

INTEGER

read-write

Used to indicate the route preference of this entry. If there are more than one route that can be used to forward IP traffic, the route that has a highest preference will be used instead of a lower preference one. The higher the number, the higher the preference.

T/F rcIpv6StaticRouteEnable

1.3.6.1.4.1.2272.1.62.1.1.6.1.8

TruthValue

read-write

Used to enable/disable this entry.

ROW rcIpv6StaticRouteRowStatus

1.3.6.1.4.1.2272.1.62.1.1.6.1.9

RowStatus

read-create

Row status for create/delete.

rcIpv6NetToPhysicalTable

1.3.6.1.4.1.2272.1.62.1.1.7

not-accessible

The IP Address Translation table used for mapping from IP addresses to physical addresses. The Address Translation tables contain the IP address to 'physical' address equivalences. Some interfaces do not use translation tables for determining address equivalences (e.g., DDN-X.25 has an algorithmic method); if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries. While many protocols may be used to populate this table, ARP [10] and Neighbor Discovery [4] are the most likely options.

rcIpv6NetToPhysicalEntry

1.3.6.1.4.1.2272.1.62.1.1.7.1

not-accessible

Each entry contains one IP address to `physical' address equivalence.

NUM rcIpv6NetToPhysicalIfIndex

1.3.6.1.4.1.2272.1.62.1.1.7.1.1

InterfaceIndex

not-accessible

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of the IfIndex field in the rcIpv6InterfaceIfIndex.

ADR rcIpv6NetToPhysicalNetAddress

1.3.6.1.4.1.2272.1.62.1.1.7.1.2

Ipv6Address

not-accessible

The IP Address corresponding to the media-dependent `physical' address. The address type of this object is specified in rcIpv6NetToPhysicalAddressType. Implementors need to be aware that if the size of rcIpv6NetToPhysicalNetAddress exceeds 115 octets then OIDS of instances of columns in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c or SNMPv3.

PHY rcIpv6NetToPhysicalPhysAddress

1.3.6.1.4.1.2272.1.62.1.1.7.1.3

PhysAddress

read-write

The media-dependent `physical' address. As the entries in this table are typically not persistent when this object is written the entity SHOULD NOT save the change to non-volatile storage. In the ethernet case it is a MAC address.

I32 rcIpv6NetToPhysicalInterface

1.3.6.1.4.1.2272.1.62.1.1.7.1.4

Integer32

read-write

The field represents either a physical port id or the MLT port id. This entry is associated either with a port or with a MLT in a VLAN/Brouter port. If the value is 0 then the interface is CP port.

TIM rcIpv6NetToPhysicalLastUpdated

1.3.6.1.4.1.2272.1.62.1.1.7.1.5

TimeStamp

read-only

The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.

INT rcIpv6NetToPhysicalType

1.3.6.1.4.1.2272.1.62.1.1.7.1.6

INTEGER

read-write

The type of mapping. The 'dynamic(2)' type indicates that the IP address to physical addresses mapping has been dynamically resolved using e.g. IPv4 ARP or the IPv6 Neighbor Discovery protocol. The 'static(3)' type indicates that the mapping has been statically configured. Both of these refer to entries that provide mappings for other entities addresses. The 'local(4)' type indicates that the mapping is provided for an entity's own interface address. As the entries in this table are typically not persistent when this object is written the entity SHOULD NOT save the change to non-volatile storage.

INT rcIpv6NetToPhysicalState

1.3.6.1.4.1.2272.1.62.1.1.7.1.8

INTEGER

read-only

The Neighbor Unreachability Detection [4] state for the interface when the address mapping in this entry is used. If Neighbor Unreachability Detection is not in use (eg. for IPv4), this object is always unknown(6). REFERENCE RFC2461

ROW rcIpv6NetToPhysicalRowStatus

1.3.6.1.4.1.2272.1.62.1.1.7.1.9

RowStatus

read-create

The status of this conceptual row. The RowStatus TC requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified. The value of this object has no effect on whether other objects in this conceptual row can be modified. A conceptual row can not be made active until the rcIpv6NetToPhysicalPhysAddress object has been set. Note that if the rcIpv6NetToPhysicalType is set to 'invalid' the managed node may delete the entry independent of the state of this object. Only createandGo and Delete operations are supported

rcIpv6PrefixListTable

1.3.6.1.4.1.2272.1.62.1.1.8

not-accessible

IPv6 Prefix List table

rcIpv6PrefixListEntry

1.3.6.1.4.1.2272.1.62.1.1.8.1

not-accessible

An entry of Ipv6 Prefix List Table.

U32 rcIpv6PrefixListId

1.3.6.1.4.1.2272.1.62.1.1.8.1.1

Unsigned32

not-accessible

Id of an IPv6 Prefix List

ADR rcIpv6PrefixListPrefix

1.3.6.1.4.1.2272.1.62.1.1.8.1.2

Ipv6Address

not-accessible

Is a member of a specific ipv6 prefix list. Adding the prefix to the given ipv6 prefix list

U32 rcIpv6PrefixListPrefixMaskLen

1.3.6.1.4.1.2272.1.62.1.1.8.1.3

Unsigned32

not-accessible

Mask length of the ipv6 prefix added to the prefix list

U32 rcIpv6PrefixListMaskLenFrom

1.3.6.1.4.1.2272.1.62.1.1.8.1.4

Unsigned32

read-create

Lower bound of mask length of the ipv6 prefix added to the prefix list

U32 rcIpv6PrefixListMaskLenUpto

1.3.6.1.4.1.2272.1.62.1.1.8.1.5

Unsigned32

read-create

Higher bound of mask length of the ipv6 prefix added to the prefix list

STR rcIpv6PrefixListName

1.3.6.1.4.1.2272.1.62.1.1.8.1.6

SnmpAdminString

read-create

Name of the Ipv6 prefix list

ROW rcIpv6PrefixListRowStatus

1.3.6.1.4.1.2272.1.62.1.1.8.1.7

RowStatus

read-create

Used to create/delete entries in the ipv6 prefix list table

rcIpv6ConfDhcpRelayTable

1.3.6.1.4.1.2272.1.62.1.1.9

not-accessible

DHCP Relay for Ipv6 configuration table

rcIpv6ConfDhcpRelayEntry

1.3.6.1.4.1.2272.1.62.1.1.9.1

not-accessible

Used to configure DHCP on a particular L3 interface. An entry is created automatically when the variable rcIpv6InterfaceDhcpEnabled is set to TRUE. Once created this entry will only be deleted if the rcIpv6ConfDhcpRowStatus is set to 'destroy(6)'. In which case, the rcIpv6InterfaceDhcpEnabled is automatically reset to the FALSE setting.

NUM rcIpv6ConfDhcpIfIndex

1.3.6.1.4.1.2272.1.62.1.1.9.1.1

InterfaceIndex

not-accessible

Interface number. The number can represent either a physical or logical(VLAN) interface.

U32 rcIpv6ConfDhcpMaxHop

1.3.6.1.4.1.2272.1.62.1.1.9.1.2

Unsigned32

read-write

Used to indicate the maximum number of hops a DHCP packet can take from the source device to the destination device (i.e., DHCP client to DHCP server).

T/F rcIpv6ConfDhcpRemoteIdEnabled

1.3.6.1.4.1.2272.1.62.1.1.9.1.3

TruthValue

read-write

Used to indicate if remote-id option is enabled.

C32 rcIpv6ConfDhcpNumRequests

1.3.6.1.4.1.2272.1.62.1.1.9.1.4

Counter32

read-only

The total number of DHCP requests seen on this interface.

C32 rcIpv6ConfDhcpNumReplies

1.3.6.1.4.1.2272.1.62.1.1.9.1.5

Counter32

read-only

The total number of DHCP replies seen on this interface.

ROW rcIpv6ConfDhcpRowStatus

1.3.6.1.4.1.2272.1.62.1.1.9.1.6

RowStatus

read-write

An entry is created automatically when the variable rcIpv6InterfaceDhcpEnabled is set to TRUE. Once created this entry will only be deleted if the rcIpv6ConfDhcpRowStatus is set to 'destroy(6)'. In which case, the rcIpv6InterfaceDhcpEnabled is automatically reset to the FALSE setting.

rcIpv6DhcpForwardTable

1.3.6.1.4.1.2272.1.62.1.1.10

not-accessible

DHCP Relay forwarding table.

rcIpv6DhcpForwardEntry

1.3.6.1.4.1.2272.1.62.1.1.10.1

not-accessible

An entry used represents a DHCP Relayed message forwarding directive.

ADR rcIpv6DhcpForwardAgentAddr

1.3.6.1.4.1.2272.1.62.1.1.10.1.1

Ipv6Address

not-accessible

The IP address configured on an interface (i.e., a locally configured IP address).

ADR rcIpv6DhcpForwardServerAddr

1.3.6.1.4.1.2272.1.62.1.1.10.1.2

Ipv6Address

not-accessible

The IP address of the DHCP server. If this IP address corresponds to a local interface address, the DHCP packet is multicast out the interface the IP address is assigned to.otherwise,the DHCP packet is sent via unicast to the remote device.

T/F rcIpv6DhcpForwardEnabled

1.3.6.1.4.1.2272.1.62.1.1.10.1.3

TruthValue

read-write

Used to indicate whether the entry should be used.

ROW rcIpv6DhcpForwardRowStatus

1.3.6.1.4.1.2272.1.62.1.1.10.1.4

RowStatus

read-write

Row status of this entry.

rcIpv6MgmtPortStaticRouteTable

1.3.6.1.4.1.2272.1.62.1.1.12

not-accessible

This table contains list of routes that are created by the user to destination networks on the management port.

rcIpv6MgmtPortStaticRouteEntry

1.3.6.1.4.1.2272.1.62.1.1.12.1

not-accessible

An entry in the static route table for IPv6 can be created for a destination with a specific prefix length; multiple entries to the same destination are created either by specifying the next-hop or interfaceIndex or both to reach the destination. However if the nexthop Ipv6 address is a link-local address then IfIndex must be supplied.

NUM rcIpv6MgmtPortStaticRouteIfIndex

1.3.6.1.4.1.2272.1.62.1.1.12.1.1

InterfaceIndex

not-accessible

The ifIndex value which identifies the local interface through which the next hop of this route should be reached. A value of 0 is valid and represents the scenario where no interface is specified.

ADR rcIpv6MgmtPortStaticRouteDest

1.3.6.1.4.1.2272.1.62.1.1.12.1.2

Ipv6Address

not-accessible

The destination IPv6 address of this route. The values for the index objects rcIpv6StaticRouteDest and rcIpv6StaticRoutePrefixLength must be consistent. When the value of rcIpv6StaticRouteDest (excluding the zone index, if one is present) is x, then the bitwise logical-AND of x with the value of the mask formed from the corresponding index object rcIpv6StaticRoutePrefixLength MUST be equal to x. If not, then the index pair is not consistent and an inconsistentName error must be returned on SET or CREATE requests.

INT rcIpv6MgmtPortStaticRoutePrefixLength

1.3.6.1.4.1.2272.1.62.1.1.12.1.3

INTEGER

not-accessible

Indicates the number of leading one bits which form the mask to be logical-ANDed with the destination address before being compared to the value in the rcIpv6MgmtPortStaticRouteDestAddr field.

ADR rcIpv6MgmtPortStaticRouteNextHop

1.3.6.1.4.1.2272.1.62.1.1.12.1.4

Ipv6Address

not-accessible

Next hop IPv6 address for this destination. On remote routes, the address of the next system en route. For non-remote routes, a zero length string.

INT rcIpv6MgmtPortStaticRouteDistance

1.3.6.1.4.1.2272.1.62.1.1.12.1.5

INTEGER

read-create

cost/distance to reach the destination for this node.

INT rcIpv6MgmtPortStaticRouteStatus

1.3.6.1.4.1.2272.1.62.1.1.12.1.6

INTEGER

read-only

(1)notReachable means the route is not reachable and no neighbor request entry is built to resolved the next-hop. It happens when there is no route or neighbor to reach the static route's next-hop. (2)tryToResolve means the route is not reachable but a neighbor request entry is built to resolved the next-hop. It happens when there is a local equivelent route in system to reach the next-hop but the neighor is not learnt yet (3)reachableNotInRtm means the static route is reachable but it is not in RTM. It happens when the static route is reachable, but it is not the best among alternative static route. (4)reachableInRtm means the static route is reachable and it is in RTM. It happens when the static route is reachable, and it is the best among alternative static route to be added into RTM.

INT rcIpv6MgmtPortStaticRoutePreference

1.3.6.1.4.1.2272.1.62.1.1.12.1.7

INTEGER

read-create

Used to indicate the route preference of this entry. If there are more than one route that can be used to forward IP traffic, the route that has a highest preference will be used instead of a lower preference one. The higher the number, the higher the preference.

T/F rcIpv6MgmtPortStaticRouteEnable

1.3.6.1.4.1.2272.1.62.1.1.12.1.8

TruthValue

read-create

Used to enable/disable this entry.

ROW rcIpv6MgmtPortStaticRouteRowStatus

1.3.6.1.4.1.2272.1.62.1.1.12.1.9

RowStatus

read-create

Row status for create/delete.

rcIpv6DestinationCacheTable

1.3.6.1.4.1.2272.1.62.1.1.13

not-accessible

Ipv6 Destination Cache table

rcIpv6DestinationCacheEntry

1.3.6.1.4.1.2272.1.62.1.1.13.1

not-accessible

Used to display Destination Cache

ADR rcIpv6DCacheDestAddr

1.3.6.1.4.1.2272.1.62.1.1.13.1.1

Ipv6Address

not-accessible

IPv6 Destination Address from the Destination Cache.

U32 rcIpv6DCacheIfIndex

1.3.6.1.4.1.2272.1.62.1.1.13.1.2

Unsigned32

not-accessible

The last 16 bits of this object's value are interpreted as InterfaceIndex (it can represent either a physical, or a VLAN, or a tunnel interface); the first 16 bits are ignored when the object's value is interpreted.

ADR rcIpv6DCacheNextHop

1.3.6.1.4.1.2272.1.62.1.1.13.1.3

Ipv6Address

read-only

Ipv6 Next Hop for a Destination Cache entry.

INT rcIpv6DCacheIfType

1.3.6.1.4.1.2272.1.62.1.1.13.1.4

INTEGER

read-only

Interface type; it can be a real (i.e. VLAN, brouter, tunnel) or a virtual circuit (i.e. VRRP, RSMLT).

STR rcIpv6DCacheIfData

1.3.6.1.4.1.2272.1.62.1.1.13.1.5

DisplayString

read-only

Used to display additional information about virtual circuits (i.e. if it is a VRRP or RSMLT circuit, the vrId if it is a VRRP circuit); no information is displayed for real circuits.

I32 rcIpv6DCachePmtu

1.3.6.1.4.1.2272.1.62.1.1.13.1.6

Integer32

read-only

Path MTU for the entry.

C32 rcIpv6DCachePmtuAge

1.3.6.1.4.1.2272.1.62.1.1.13.1.7

Counter32

read-only

Indicates how much time (in seconds) has passed since the PMTU was updated the last time.

rcIsis

1.3.6.1.4.1.2272.1.63

rcIsisGlobalGroup

1.3.6.1.4.1.2272.1.63.1

INT rcIsisGlobalAreaAuthType

1.3.6.1.4.1.2272.1.63.1.1

INTEGER

read-write

The authentication type for the area

I32 rcIsisGlobalAreaKeyId

1.3.6.1.4.1.2272.1.63.1.2

Integer32

read-write

Authentication key-id for the area. This is required if the auth-type is hmac-md5 else it is not required.

OCT rcIsisGlobalAreaAuthKey

1.3.6.1.4.1.2272.1.63.1.3

OCTET STRING

read-write

Authentication key, this key will be used to authenticate the LSP's received on the area

INT rcIsisGlobalDomainAuthType

1.3.6.1.4.1.2272.1.63.1.4

INTEGER

read-write

The authentication type for the domain

I32 rcIsisGlobalDomainKeyId

1.3.6.1.4.1.2272.1.63.1.5

Integer32

read-write

The authentication key-id for the domain. This is required if the auth-type is hmac-md5 else it is not required.

OCT rcIsisGlobalDomainAuthKey

1.3.6.1.4.1.2272.1.63.1.6

OCTET STRING

read-write

Authentication key, this key will be used to authenticate the LSP's received on the domain

I32 rcIsisGlobalCsnpInt

1.3.6.1.4.1.2272.1.63.1.7

Integer32

read-write

Interval of time, in seconds, between periodic transmission of a complete set of CSNPs on multiaccess networks if this router is the designated router at this level. This object follows the resettingTimer behavior. For ResettingTimer description see the ISIS MIB

I32 rcIsisGlobalRxmtLspInt

1.3.6.1.4.1.2272.1.63.1.8

Integer32

read-write

Minimum interval, in seconds, between re-transmission of a LSP at this level. This object follows the resettingTimer behavior. For ResettingTimer description see the ISIS MIB

I32 rcIsisGlobalPSNPInterval

1.3.6.1.4.1.2272.1.63.1.9

Integer32

read-write

Minimum interval in seconds between sending Partial Sequence Number PDUs at this level. This object follows the resettingTimer behavior. For ResettingTimer description see the ISIS MIB

OCT rcIsisGlobalHostName

1.3.6.1.4.1.2272.1.63.1.10

OCTET STRING

read-write

The hostname listed in LSP, or the system name if host name is not configured.

I32 rcIsisGlobalSpfDelay

1.3.6.1.4.1.2272.1.63.1.11

Integer32

read-write

ISIS SPF delay in miliseconds

I32 rcIsisGlobalControlVlan

1.3.6.1.4.1.2272.1.63.1.12

Integer32

read-write

ISIS control vlan ID

IP rcIsisGlobalIpSourceAddress

1.3.6.1.4.1.2272.1.63.1.13

InetAddress

read-write

ISIS PLSB IP address. Define an existing router interface for management (ping/traceroute)

IPt rcIsisGlobalIpSourceAddressType

1.3.6.1.4.1.2272.1.63.1.14

InetAddressType

read-write

The type of address for existing router interface for management (ping/traceroute)

rcIsisCircuitTable

1.3.6.1.4.1.2272.1.63.2

not-accessible

Table of IS-IS Circuit, this is extension to the isisCircTable defined in ISIS MIB

rcIsisCircuitEntry

1.3.6.1.4.1.2272.1.63.2.1

not-accessible

An entry of rcIsisCircuit Table. A Entry in table exists for each ISIS circuit created

I32 rcIsisCircuitIndex

1.3.6.1.4.1.2272.1.63.2.1.1

Integer32

not-accessible

The identifier of this circuit, unique within the Intermediate System. This object follows the index behavior. This is for SNMP Indexing purposes only and need not have any relation to any protocol value.

INT rcIsisCircuitType

1.3.6.1.4.1.2272.1.63.2.1.2

INTEGER

read-write

ISIS circuit type this is an extention to ISIS circuit table, this was required a standard MIB circuit type does not support passive type

INT rcIsisCircuitAuthType

1.3.6.1.4.1.2272.1.63.2.1.3

INTEGER

read-write

Authentication type for IIH to be sent/reveived on the circuit/interface

INT rcIsisCircuitKeyId

1.3.6.1.4.1.2272.1.63.2.1.4

INTEGER

read-write

Authentication key id related to IIH key This can be set only if the auth-type is hmac-md5

OCT rcIsisCircuitAuthKey

1.3.6.1.4.1.2272.1.63.2.1.5

OCTET STRING

read-write

Authentication key to be used to authenticate IIH sent/reveived on the circuit/interface

IP rcIsisCircuitAddr

1.3.6.1.4.1.2272.1.63.2.1.6

IpAddress

read-only

IP address associated with the interface

IP rcIsisCircuitMask

1.3.6.1.4.1.2272.1.63.2.1.7

IpAddress

read-only

IP mask associated with the interface

INT rcIsisCircuitOperState

1.3.6.1.4.1.2272.1.63.2.1.8

INTEGER

read-only

This variable tells the operating state of circ

I32 rcIsisCircuitNumAdj

1.3.6.1.4.1.2272.1.63.2.1.9

Integer32

read-only

NUmber of adjacencies

I32 rcIsisCircuitNumUpAdj

1.3.6.1.4.1.2272.1.63.2.1.10

Integer32

read-only

Number of adjancencies which are UP

rcIsisStats

1.3.6.1.4.1.2272.1.63.3

T/F rcIsisStatsClearErrorCounters

1.3.6.1.4.1.2272.1.63.3.1

TruthValue

read-write

Clear ISIS global and interface error counters.

T/F rcIsisStatsClearPacketCounters

1.3.6.1.4.1.2272.1.63.3.2

TruthValue

read-write

Clear IS-IS control packets sent and received at each level on all the interface/circuits.

rcIsisPlsbTable

1.3.6.1.4.1.2272.1.63.4

not-accessible

Table of PLSB under IS-IS

rcIsisPlsbEntry

1.3.6.1.4.1.2272.1.63.4.1

not-accessible

An entry of rcIsisPlsb Table. A Entry in table exists for each plsb instance created

I32 rcIsisPlsbId

1.3.6.1.4.1.2272.1.63.4.1.1

Integer32

not-accessible

PLSB instance ID

ROW rcIsisPlsbRowStatus

1.3.6.1.4.1.2272.1.63.4.1.2

RowStatus

read-create

The state of the rcIsisPlsbEntry.

ISI rcIsisPlsbNodeNickName

1.3.6.1.4.1.2272.1.63.4.1.3

IsisPlsbNodeNickName

read-create

PLSB node's nickname is used to calculate ISID multicast mac address.

OCT rcIsisPlsbVlans

1.3.6.1.4.1.2272.1.63.4.1.4

OCTET STRING

read-create

PLSB ISIS vlans for a PLSB instance.

ENA rcIsisPlsbLsdbTrap

1.3.6.1.4.1.2272.1.63.4.1.5

EnableValue

read-create

isis PLSB lsdb update trap enable on this plsb instance

ENA rcIsisPlsbState

1.3.6.1.4.1.2272.1.63.4.1.6

EnableValue

read-create

enable/disable PLSB.

ENA rcIsisPlsbIpShortcut

1.3.6.1.4.1.2272.1.63.4.1.7

EnableValue

read-create

ISIS PLSB IP shortcut enabled

I32 rcIsisPlsbPrimaryVlan

1.3.6.1.4.1.2272.1.63.4.1.8

Integer32

read-create

Primary Vlan Id for this plsb instance.

INT rcIsisPlsbSmltSplitBEB

1.3.6.1.4.1.2272.1.63.4.1.9

INTEGER

read-only

ISIS PLSB SMLT split BEB for this plsb instance.

MAC rcIsisPlsbSmltBmac

1.3.6.1.4.1.2272.1.63.4.1.10

MacAddress

read-create

ISIS PLSB SMLT virtual MAC for this plsb instance.

ISI rcIsisPlsbSmltPeerSysId

1.3.6.1.4.1.2272.1.63.4.1.11

IsisSystemID

read-create

ISIS PLSB SMLT Peer's system-id for this plsb instance.

rcIsisCircuitPlsbTable

1.3.6.1.4.1.2272.1.63.5

not-accessible

Table of IS-IS Circuit PLSB instance

rcIsisCircuitPlsbEntry

1.3.6.1.4.1.2272.1.63.5.1

not-accessible

An entry of rcIsisCircuitPlsb Table. A Entry in table exists for each PLSB instance under a ISIS circuit created

I32 rcIsisCircuitPlsbIndex

1.3.6.1.4.1.2272.1.63.5.1.1

Integer32

not-accessible

The identifier of this circuit, unique within the Intermediate System. This object follows the index behavior. This is for SNMP Indexing purposes only and need not have any relation to any protocol value.

I32 rcIsisCircuitPlsbId

1.3.6.1.4.1.2272.1.63.5.1.2

Integer32

not-accessible

PLSB instance ID

ROW rcIsisCircuitPlsbRowStatus

1.3.6.1.4.1.2272.1.63.5.1.3

RowStatus

read-create

The state of the rcIsisCircuitPlsbEntry.

ENA rcIsisCircuitPlsbState

1.3.6.1.4.1.2272.1.63.5.1.4

EnableValue

read-create

PLSB functionality enable on this Plsb instance at this port

INT rcIsisCircuitPlsbType

1.3.6.1.4.1.2272.1.63.5.1.5

INTEGER

read-create

ISIS circuit type this is an extention to ISIS circuit table, this was required a standard MIB circuit type does not support passive type

ISI rcIsisCircuitPlsbL1Metric

1.3.6.1.4.1.2272.1.63.5.1.6

IsisDefaultL1Metric

read-create

The metric value of this circuit for this level.

ISI rcIsisCircuitPlsbWideL1Metric

1.3.6.1.4.1.2272.1.63.5.1.7

IsisWideL1Metric

read-create

The metric value of this circuit for this level.

rcIsisTrap

1.3.6.1.4.1.2272.1.63.9

STR rcIsisLocalLspId

1.3.6.1.4.1.2272.1.63.9.1

DisplayString

read-only

The 8 byte Local LSP ID, consisting of the SystemID, Circuit ID, and Fragment Number.

ISI rcIsisLocall1Metric

1.3.6.1.4.1.2272.1.63.9.2

IsisDefaultL1Metric

read-only

l1-metric for ISIS interface on local Node.

STR rcIsisNgbLspId

1.3.6.1.4.1.2272.1.63.9.3

DisplayString

read-only

The 8 byte neighbor LSP ID, consisting of the SystemID, Circuit ID, and Fragment Number.

ISI rcIsisNgbl1Metric

1.3.6.1.4.1.2272.1.63.9.4

IsisDefaultL1Metric

read-only

l1-metric for ISIS interface on neighbor Node.

INT rcIsisPlsbTrapType

1.3.6.1.4.1.2272.1.63.9.5

INTEGER

read-only

STR rcIsisLocalSysId

1.3.6.1.4.1.2272.1.63.9.6

DisplayString

read-only

ISIS local node system-id.

I32 rcIsisLocalInterface

1.3.6.1.4.1.2272.1.63.9.7

Integer32

read-only

ISIS local interface index.

INT rcIsisTrapIndicator

1.3.6.1.4.1.2272.1.63.9.8

INTEGER

read-only

indicates that an alarm has been Raised, or an alarm has been cleared.

STR rcIsisLocalNickname

1.3.6.1.4.1.2272.1.63.9.9

DisplayString

read-only

ISIS local node nick-name.

STR rcIsisNgbNickname

1.3.6.1.4.1.2272.1.63.9.10

DisplayString

read-only

ISIS neighbor node nick-name.

STR rcIsisNgbSysId

1.3.6.1.4.1.2272.1.63.9.11

DisplayString

read-only

ISIS neighbor node system-id.

ISI rcIsisLocalPrimaryBvid

1.3.6.1.4.1.2272.1.63.9.12

IsisPlsbBvid

read-only

ISIS local primary B-VID.

ISI rcIsisLocalPrimaryTieBrkAlg

1.3.6.1.4.1.2272.1.63.9.13

IsisPlsbBvidTieBrkAlg

read-only

The tie breaking algorithm applied to local primary B-VID.

ISI rcIsisLocalSecondaryBvid

1.3.6.1.4.1.2272.1.63.9.14

IsisPlsbBvid

read-only

ISIS local secondary B-VID.

ISI rcIsisLocalSecondaryTieBrkAlg

1.3.6.1.4.1.2272.1.63.9.15

IsisPlsbBvidTieBrkAlg

read-only

The tie breaking algorithm applied to local seconday B-VID.

ISI rcIsisNgbPrimaryBvid

1.3.6.1.4.1.2272.1.63.9.16

IsisPlsbBvid

read-only

ISIS neighbor primary B-VID.

ISI rcIsisNgbPrimaryTieBrkAlg

1.3.6.1.4.1.2272.1.63.9.17

IsisPlsbBvidTieBrkAlg

read-only

The neighbor tie breaking algorithm applied to primary B-VID.

ISI rcIsisNgbSecondaryBvid

1.3.6.1.4.1.2272.1.63.9.18

IsisPlsbBvid

read-only

ISIS neighbor secondary B-VID.

ISI rcIsisNgbSecondaryTieBrkAlg

1.3.6.1.4.1.2272.1.63.9.19

IsisPlsbBvidTieBrkAlg

read-only

The neighbor tie breaking algorithm applied to secondary B-VID.

MAC rcIsisLocalVirtualBmac

1.3.6.1.4.1.2272.1.63.9.20

MacAddress

read-only

The SMLT Virtual BMAC configured in the local IST switch.

MAC rcIsisPeerVirtualBmac

1.3.6.1.4.1.2272.1.63.9.21

MacAddress

read-only

The SMLT Virtual BMAC configured in the IST Peer.

STR rcIsisSysId

1.3.6.1.4.1.2272.1.63.9.22

DisplayString

read-only

The isis system id configured in the local switch or IST peer.

STR rcIsisSmltPeerSysId

1.3.6.1.4.1.2272.1.63.9.23

DisplayString

read-only

The SMLT Peer system-id configured in the local switch or IST Peer.

INT rcIsisAdjState

1.3.6.1.4.1.2272.1.63.9.24

INTEGER

read-only

indicate different ISIS adjacency states.

INT rcIsisDuplicateNnameCounter

1.3.6.1.4.1.2272.1.63.9.25

INTEGER

read-only

indicate how many nodes in the network share the nick-name.

INT rcIsisLocalBvidCounter

1.3.6.1.4.1.2272.1.63.9.26

INTEGER

read-only

indicate how many b-vid configured on local nodes.

INT rcIsisNgbBvidCounter

1.3.6.1.4.1.2272.1.63.9.27

INTEGER

read-only

indicate how many b-vid configured on a neighbor nodes.

INT rcIsisLocalSmltSplitBeb

1.3.6.1.4.1.2272.1.63.9.28

INTEGER

read-only

The SMLT Split-BEB configured in the local IST switch.

INT rcIsisPeerSmltSplitBeb

1.3.6.1.4.1.2272.1.63.9.29

INTEGER

read-only

The SMLT Split-BEB configured in the IST Peer switch.

OCT rcIsisLocalHostName

1.3.6.1.4.1.2272.1.63.9.30

OCTET STRING

read-only

ISIS local host name.

OCT rcIsisNgbHostName

1.3.6.1.4.1.2272.1.63.9.31

OCTET STRING

read-only

ISIS neighbor host name.

I32 rcIsisPrevInterface

1.3.6.1.4.1.2272.1.63.9.32

Integer32

read-only

ISIS local interface index for previously found adj.

rcIsisAdjTable

1.3.6.1.4.1.2272.1.63.10

not-accessible

Table of IS-IS Adjacency, this is extension to the isisISAdjTable defined in ISIS MIB

rcIsisAdjEntry

1.3.6.1.4.1.2272.1.63.10.1

not-accessible

An entry of rcIsisAdj Table. A Entry in table exists for each ISIS adjacency

I32 rcIsisAdjCircIndex

1.3.6.1.4.1.2272.1.63.10.1.1

Integer32

not-accessible

The identifier of this circuit, unique within the Intermediate System. This object follows the index behavior. This is for SNMP Indexing purposes only and need not have any relation to any protocol value.

U32 rcIsisAdjIndex

1.3.6.1.4.1.2272.1.63.10.1.2

Unsigned32

not-accessible

A unique value identifying the IS adjacency from all other such adjacencies on this circuit. This value is automatically assigned by the system when the adjacency is created.

OCT rcIsisAdjHostName

1.3.6.1.4.1.2272.1.63.10.1.3

OCTET STRING

read-only

The hostname listed in LSP, or the system name if host name is not configured.

NUM rcIsisAdjIfIndex

1.3.6.1.4.1.2272.1.63.10.1.4

InterfaceIndex

read-only

The value of ifIndex for the interface to which this circuit corresponds.

rcIsisLSPTable

1.3.6.1.4.1.2272.1.63.11

not-accessible

Table of IS-IS LSP, this is extension to the isisLSPSummaryTable defined in ISIS MIB

rcIsisLSPEntry

1.3.6.1.4.1.2272.1.63.11.1

not-accessible

An entry of rcIsisLSP Table. A Entry in table exists for each ISIS LSP

INT rcIsisLSPLevel

1.3.6.1.4.1.2272.1.63.11.1.1

INTEGER

not-accessible

At which level does this LSP appear?

OCT rcIsisLSPID

1.3.6.1.4.1.2272.1.63.11.1.2

OCTET STRING

not-accessible

The 8 byte LSP ID, consisting of the SystemID, Circuit ID, and Fragment Number.

U32 rcIsisLSPSeq

1.3.6.1.4.1.2272.1.63.11.1.3

Unsigned32

read-only

The sequence number for this LSP.

OCT rcIsisLSPHostName

1.3.6.1.4.1.2272.1.63.11.1.4

OCTET STRING

read-only

The hostname listed in LSP, or the system name if host name is not configured.

I32 rcIsisLSPNickName

1.3.6.1.4.1.2272.1.63.11.1.5

Integer32

read-only

PLSB node's nickname

U32 rcIsisLSPLifetimeRemain

1.3.6.1.4.1.2272.1.63.11.1.6

Unsigned32

read-only

The remaining lifetime in seconds for this LSP.

rcIsisPlsbIpUnicastFibTable

1.3.6.1.4.1.2272.1.63.12

not-accessible

Table of IS-IS PLSB IP Unicast FIB

rcIsisPlsbIpUnicastFibEntry

1.3.6.1.4.1.2272.1.63.12.1

not-accessible

An entry of rcIsisPlsbIpUnicastFib Table. A Entry in table exists for each PLSB IP unicast forwarding entry.

I32 rcIsisPlsbIpUnicastFibVrfId

1.3.6.1.4.1.2272.1.63.12.1.1

Integer32

not-accessible

VRF ID of the IP unicast FIB entry, 0 indicates NRE.

IPt rcIsisPlsbIpUnicastFibDestinationIpAddrType

1.3.6.1.4.1.2272.1.63.12.1.2

InetAddressType

not-accessible

The address type of destination IP Address.

IP rcIsisPlsbIpUnicastFibDestinationIpAddr

1.3.6.1.4.1.2272.1.63.12.1.3

InetAddress

not-accessible

Destination IP Address of the IP unicast FIB entry. Support ipv4 size(4) and ipv6 size(16)

ADR rcIsisPlsbIpUnicastFibDestinationMask

1.3.6.1.4.1.2272.1.63.12.1.4

InetAddressPrefixLength

not-accessible

Destination IP mask of the IP unicast FIB entry

MAC rcIsisPlsbIpUnicastFibNextHopBmac

1.3.6.1.4.1.2272.1.63.12.1.5

MacAddress

not-accessible

the nexthop BMAC of the IP unicast FIB entry

I32 rcIsisPlsbIpUnicastFibVlan

1.3.6.1.4.1.2272.1.63.12.1.6

Integer32

not-accessible

Vlan of the IP unicast FIB entry

I32 rcIsisPlsbIpUnicastFibIsid

1.3.6.1.4.1.2272.1.63.12.1.7

Integer32

read-only

ISID of the IP unicast FIB entry

STR rcIsisPlsbIpUnicastFibNextHopName

1.3.6.1.4.1.2272.1.63.12.1.8

DisplayString

read-only

the nexthop hostname of the IP unicast FIB entry

NUM rcIsisPlsbIpUnicastFibOutgoingPort

1.3.6.1.4.1.2272.1.63.12.1.9

InterfaceIndex

read-only

Outgoing port of the IP unicast Fib entry.

I32 rcIsisPlsbIpUnicastFibPrefixCost

1.3.6.1.4.1.2272.1.63.12.1.10

Integer32

read-only

prefix cost of the IP unicast FIB entry

C64 rcIsisPlsbIpUnicastFibSpbmCost

1.3.6.1.4.1.2272.1.63.12.1.11

Counter64

read-only

bmac cost of the IP unicast FIB entry

rcIsisPlsbUcastFibTable

1.3.6.1.4.1.2272.1.63.13

not-accessible

Table of IS-IS PLSB Unicast FIB

rcIsisPlsbUcastFibEntry

1.3.6.1.4.1.2272.1.63.13.1

not-accessible

An entry of rcIsisPlsbUcastFib Table. A Entry in table exists for each PLSB unicast forwarding entry generated by ISIS SPF computation

OCT rcIsisPlsbUcastFibSysId

1.3.6.1.4.1.2272.1.63.13.1.1

OCTET STRING

not-accessible

System ID of the node where unicast FIB entry come from

I32 rcIsisPlsbUcastFibVlan

1.3.6.1.4.1.2272.1.63.13.1.2

Integer32

not-accessible

Vlan of the unicast FIB entry

MAC rcIsisPlsbUcastFibDestinationMacAddr

1.3.6.1.4.1.2272.1.63.13.1.3

MacAddress

not-accessible

Destination Mac Address of the unicast FIB entry

NUM rcIsisPlsbUcastFibOutgoingPort

1.3.6.1.4.1.2272.1.63.13.1.4

InterfaceIndex

read-only

Outgoing port of the unicast Fib entry.

OCT rcIsisPlsbUcastFibHostName

1.3.6.1.4.1.2272.1.63.13.1.5

OCTET STRING

read-only

Host name of the node where unicast FIB entry come from

C64 rcIsisPlsbUcastFibCost

1.3.6.1.4.1.2272.1.63.13.1.6

Counter64

read-only

unicast FIB cost

rcIsisPlsbMcastFibTable

1.3.6.1.4.1.2272.1.63.14

not-accessible

Table of IS-IS PLSB Multicast FIB

rcIsisPlsbMcastFibEntry

1.3.6.1.4.1.2272.1.63.14.1

not-accessible

An entry of rcIsisPlsbMcastFib Table. A Entry in table exists for each PLSB Multicast forwarding entry generated by ISIS SPF computation

OCT rcIsisPlsbMcastFibSysId

1.3.6.1.4.1.2272.1.63.14.1.1

OCTET STRING

not-accessible

System ID of the node where multicast FIB entry come from

I32 rcIsisPlsbMcastFibVlan

1.3.6.1.4.1.2272.1.63.14.1.2

Integer32

not-accessible

Vlan of the multicast FIB entry

MAC rcIsisPlsbMcastFibMcastDestMacAddr

1.3.6.1.4.1.2272.1.63.14.1.3

MacAddress

not-accessible

Multicast destination Mac Address of the multicast FIB entry

I32 rcIsisPlsbMcastFibIsid

1.3.6.1.4.1.2272.1.63.14.1.4

Integer32

read-only

Isid id of the multicast FIB entry

I32 rcIsisPlsbMcastFibNickName

1.3.6.1.4.1.2272.1.63.14.1.5

Integer32

read-only

nick name of node where this i-sid got configured or discovered

INT rcIsisPlsbMcastFibType

1.3.6.1.4.1.2272.1.63.14.1.6

INTEGER

read-only

PLSB i-sid type

STR rcIsisPlsbMcastFibOutgoingPorts

1.3.6.1.4.1.2272.1.63.14.1.7

DisplayString

read-only

Nni port of the multicast Fib entry.

OCT rcIsisPlsbMcastFibHostName

1.3.6.1.4.1.2272.1.63.14.1.8

OCTET STRING

read-only

Host name of the node where multicast FIB entry come from

rcIsisPlsbNodeTable

1.3.6.1.4.1.2272.1.63.15

not-accessible

Table of IS-IS PLSB Node

rcIsisPlsbNodeEntry

1.3.6.1.4.1.2272.1.63.15.1

not-accessible

An entry of rcIsisPlsbNode Table. A Entry in table exists for each node running PLSB ISIS in the setup.

OCT rcIsisPlsbNodeSysId

1.3.6.1.4.1.2272.1.63.15.1.1

OCTET STRING

not-accessible

System ID of the PLSB node entry

OCT rcIsisPlsbNodePrimaryParentSysId

1.3.6.1.4.1.2272.1.63.15.1.2

OCTET STRING

read-only

System ID of parent node of the PLSB node entry for primary bvlan

I32 rcIsisPlsbNodePrimaryBvlan

1.3.6.1.4.1.2272.1.63.15.1.3

Integer32

read-only

spbm primary b-vlan

OCT rcIsisPlsbNodeSecondaryParentSysId

1.3.6.1.4.1.2272.1.63.15.1.4

OCTET STRING

read-only

System ID of parent node of the PLSB node entry for secondary bvlan

I32 rcIsisPlsbNodeSecondaryBvlan

1.3.6.1.4.1.2272.1.63.15.1.5

Integer32

read-only

spbm secondary b-vlan

rcSlpp

1.3.6.1.4.1.2272.1.64

rcSlppMib

1.3.6.1.4.1.2272.1.64.1

rcSlppNotifications

1.3.6.1.4.1.2272.1.64.1.0

NTF rcnSlppPortDownEventNew

1.3.6.1.4.1.2272.1.64.1.0.2

A port down event that has occurred due to SLPP. The trap includes the port and its Vlan which receives the packet, and along with the Vlan ID and source MAC address of the packet coming in on the port identified.

rcSlppObjects

1.3.6.1.4.1.2272.1.64.1.1

rcSlppScalars

1.3.6.1.4.1.2272.1.64.1.1.1

T/F rcSlppGlobalEnable

1.3.6.1.4.1.2272.1.64.1.1.1.1

TruthValue

read-write

Global enable/disable for the simple loop prevention protocol.

INT rcSlppTransmissionInterval

1.3.6.1.4.1.2272.1.64.1.1.1.2

INTEGER

read-write

The interval (in seconds) for which loop detection occurs.

bgpPeerLastError	OBJECT-TYPE
bgpPeerRemoteAddr	OBJECT-TYPE
bgpPeerState	OBJECT-TYPE

dvmrpInterfaceIfIndex	OBJECT-TYPE
dvmrpInterfaceOperState	OBJECT-TYPE
dvmrpNeighborAddress	OBJECT-TYPE
dvmrpNeighborIfIndex	OBJECT-TYPE

igmpCacheAddress	OBJECT-TYPE
igmpCacheIfIndex	OBJECT-TYPE
igmpInterfaceIfIndex	OBJECT-TYPE
igmpInterfaceQuerier	OBJECT-TYPE

MplsExtendedTunnelId
MplsLSPID
MplsLabel
MplsLdpIdentifier
MplsTunnelIndex
MplsTunnelInstanceIndex

What Is RAPID-CITY-VSP?

Supported Devices

Monitoring Examples

What Can Be Monitored

How to Use in IPNetwork Monitor

RFC description

Ipv6Address
Ipv6AddressIfIdentifier
Ipv6AddressPrefix
Ipv6IfIndex
Ipv6IfIndexOrZero

DisplayString
PhysAddress
ifAdminStatus
ifIndex
ifOperStatus
ipNetToMediaNetAddress
ipNetToMediaPhysAddress

MODULE-COMPLIANCE
OBJECT-GROUP

RAPID-CITY-VSP (page 1 of 2)

What Is RAPID-CITY-VSP?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

How to Use in IPNetwork Monitor

RFC description