All MIBs › RC-OSPF-MIB
Organization: Bay Networks, Rapid-City Group
Last Updated: 2012-05-14
Description: MIB for OSPF routing configuration, interface parameters, BFD integration, and adjacency/route statistics on Nortel Accelar/ERS switches
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is RC-OSPF-MIB?
RC-OSPF-MIB is a Nortel Accelar/ERS enterprise MIB managing OSPF routing protocol configuration, extending beyond the standard OSPF-MIB with per-interface parameters and BFD (Bidirectional Forwarding Detection) integration. It exposes per-interface OSPF settings such as router priority, cost metric, authentication key/type, hello and dead intervals, area ID, and row status for enabling/disabling OSPF on an interface, plus aggregate adjacency/route statistics. It supports software/protocol-state monitoring: administrators can verify OSPF timers and authentication are correctly configured per interface and watch adjacency/route statistics to detect neighbor flaps or route-table instability. It explicitly extends the IETF standard OSPF-MIB (RFC 1850/4750) with vendor-specific interface and BFD parameters. It is deployed on Nortel Accelar/Ethernet Routing Switch (ERS) platforms running OSPF in enterprise or service-provider networks. Engineers can download the RC-OSPF-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in RC-OSPF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Nortel Accelar / Ethernet Routing Switch (ERS)
Monitoring Examples
An operator polls rcIpConfOspfTable/rcIpConfOspfEntry keyed by rcIpConfOspfIfIndex to confirm rcIpConfOspfHelloInterval and rcIpConfOspfRtrDeadInterval match neighboring routers, since a mismatch here is a common cause of adjacencies failing to form. rcIpConfOspfAuthType and rcIpConfOspfAuthKey are checked when troubleshooting authentication failures, and rcStatOspf statistics are monitored to track adjacency state changes and route count fluctuations that may indicate an unstable OSPF area.
What Can Be Monitored
- OSPF hello/dead interval per interface
- OSPF authentication type/key
- router priority and area ID
- adjacency/route statistics
- interface OSPF enable status
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndexOrZero |
From RAISECOM-OSPF-MIB
| rcOspf | MODULE-IDENTITY |
From RAPID-CITY
| EnableValue | |
| rcIpConf | OBJECT-IDENTITY |
| rcStat | OBJECT-IDENTITY |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| TimeTicks |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| rcIpConfOspfTable | 1.3.6.1.4.1.2272.1.8.1.2 | not-accessible | A table used to maintain OSPF information for a particular interface. | |
| rcIpConfOspfEntry | 1.3.6.1.4.1.2272.1.8.1.2.1 | not-accessible | Entry containing OSPF information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface. | |
| NUM rcIpConfOspfIfIndex | 1.3.6.1.4.1.2272.1.8.1.2.1.1 | InterfaceIndexOrZero | read-only | An unique value to identify a physical interface or a logical interface (VLAN). |
| INT rcIpConfOspfRtrPriority | 1.3.6.1.4.1.2272.1.8.1.2.1.2 | INTEGER | read-write | The priority of this interface. Used in multi- access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker. |
| INT rcIpConfOspfMetric | 1.3.6.1.4.1.2272.1.8.1.2.1.3 | INTEGER | read-write | The metric for this type of service (TOS) on this interface. The default value of the TOS 0 Metric is (10^9 / ifSpeed). The value FFFF means 'no route via this TOS'. A value of 0 means the interface speed (rcIpConfOspfDefaultMetric) will be used as metric value, when the state of the interface is up. |
| STR rcIpConfOspfAuthKey | 1.3.6.1.4.1.2272.1.8.1.2.1.4 | DisplayString | read-write | The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfIfAuthKey always returns an Octet String of length zero. |
| ROW rcIpConfOspfRowStatus | 1.3.6.1.4.1.2272.1.8.1.2.1.5 | RowStatus | read-write | Row status for this entry. |
| INT rcIpConfOspfHelloInterval | 1.3.6.1.4.1.2272.1.8.1.2.1.6 | INTEGER | read-write | The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network. |
| INT rcIpConfOspfRtrDeadInterval | 1.3.6.1.4.1.2272.1.8.1.2.1.7 | INTEGER | read-write | The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network. |
| IP rcIpConfOspfIfAreaId | 1.3.6.1.4.1.2272.1.8.1.2.1.8 | IpAddress | read-write | A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone. |
| INT rcIpConfOspfAuthType | 1.3.6.1.4.1.2272.1.8.1.2.1.9 | INTEGER | read-write | The authentication type specified for an interface. Additional authentication types may be assigned locally. |
| INT rcIpConfOspfPollInterval | 1.3.6.1.4.1.2272.1.8.1.2.1.10 | INTEGER | read-write | OSPF NBMA Interface Poll Interval. |
| INT rcIpConfOspfIfMtuIgnore | 1.3.6.1.4.1.2272.1.8.1.2.1.11 | INTEGER | read-write | Mtu-ignore flag is for ignoring the mtu checking in ospf bdb |
| ENA rcIpConfOspfBfdEnable | 1.3.6.1.4.1.2272.1.8.1.2.1.12 | EnableValue | read-write | Used to enable/disable BFD for OSPF. |
| rcIpConfOspfDefaultMetric | 1.3.6.1.4.1.2272.1.8.1.3 | |||
| INT rcIpConfOspfDefaultMetric10MegPort | 1.3.6.1.4.1.2272.1.8.1.3.1 | INTEGER | read-write | Used to indicate the cost associated with 10Meg Interface(Port). |
| INT rcIpConfOspfDefaultMetric100MegPort | 1.3.6.1.4.1.2272.1.8.1.3.2 | INTEGER | read-write | Used to indicate the cost associated with 100Meg Interface(Port). |
| INT rcIpConfOspfDefaultMetric1000MegPort | 1.3.6.1.4.1.2272.1.8.1.3.3 | INTEGER | read-write | Used to indicate the cost associated with 1000Meg Interface(Port). |
| INT rcIpConfOspfDefaultMetric10000MegPort | 1.3.6.1.4.1.2272.1.8.1.3.4 | INTEGER | read-write | Used to indicate the cost associated with 10000Meg Interface(Port). |
| INT rcIpConfOspfDefaultMetric40000MegPort | 1.3.6.1.4.1.2272.1.8.1.3.5 | INTEGER | read-write | Used to indicate the cost associated with 40000Meg Interface(Port). |
| rcIpConfOspf | 1.3.6.1.4.1.2272.1.8.1.4 | |||
| T/F rcIpConfOspfTrapEnable | 1.3.6.1.4.1.2272.1.8.1.4.1 | TruthValue | read-write | Used to indicate whether Ospf Traps should be sent. |
| T/F rcIpConfOspfAutoVirtLinkEnable | 1.3.6.1.4.1.2272.1.8.1.4.2 | TruthValue | read-write | Used to indicate whether auto virtual link creation is enabled or not. If set to true OSPF will create virtual links between ABRs whether it is needed or not, but adjacency will established only when one of the ABR losses connection to backbone area. If set to false then it is user resposibity to create virtual link whenever needed. |
| INT rcIpConfOspfSpfHoldDownTime | 1.3.6.1.4.1.2272.1.8.1.4.3 | INTEGER | read-write | The SPF Hold Down Timer value. The SPF will run at most once per hold down timer value. |
| INT rcIpConfOspfAction | 1.3.6.1.4.1.2272.1.8.1.4.4 | INTEGER | read-write | |
| T/F rcIpConfOspfRfc1583Compatibility | 1.3.6.1.4.1.2272.1.8.1.4.5 | TruthValue | read-write | Controls the preference rules used when choosing among multiple AS-External-LSAs advertising the same destination. When this is enabled, the preference rule will be same as specified by RFC1583. When disabled, the new preference rule as described in RFC2328 will be applicable, which potentially prevents the routing loops when AS-External-LSAs for the same destination have been originated from different areas. |
| rcIpConfOspfAreaTable | 1.3.6.1.4.1.2272.1.8.1.7 | not-accessible | A table used to maintain OSPF information for a particular Area. | |
| rcIpConfOspfAreaEntry | 1.3.6.1.4.1.2272.1.8.1.7.1 | not-accessible | Entry containing OSPF Area configuration information. An entry is automatically created in this table when an area is configured through ospfAreaTable in (rfc1253rcc.mib). | |
| IP rcIpConfOspfAreaId | 1.3.6.1.4.1.2272.1.8.1.7.1.1 | IpAddress | read-only | An unique value to identify an area. Area ID 0.0.0.0 is used for the OSPF backbone. |
| T/F rcIpConfOspfAreaImportSummary | 1.3.6.1.4.1.2272.1.8.1.7.1.2 | TruthValue | read-write | The area's support for importing Summary advertisements into a stub area. This field should be used only if ospfImportASExtern is set to FALSE |
| I32 rcIpConfOspfAreaActiveIfCount | 1.3.6.1.4.1.2272.1.8.1.7.1.3 | Integer32 | read-only | This variable displays the number of active interfaces configured in this area. An area cannot be deleted if this value is > 0. |
| rcIpConfOspfV2Table | 1.3.6.1.4.1.2272.1.8.1.9 | not-accessible | A table used to maintain OSPF information for a particular interface. | |
| rcIpConfOspfV2Entry | 1.3.6.1.4.1.2272.1.8.1.9.1 | not-accessible | Entry containing OSPF information. An entry is automatically created in this table when routing is enabled for an interface -or- when an ip address is configured on an interface. | |
| NUM rcIpConfOspfV2IfIndex | 1.3.6.1.4.1.2272.1.8.1.9.1.1 | InterfaceIndexOrZero | read-only | An unique value to identify a physical interface or a logical interface (VLAN). |
| IP rcIpConfOspfV2IpAddr | 1.3.6.1.4.1.2272.1.8.1.9.1.2 | IpAddress | read-only | IpAddress of the IP interface. |
| INT rcIpConfOspfV2RtrPriority | 1.3.6.1.4.1.2272.1.8.1.9.1.3 | INTEGER | read-write | The priority of this interface. Used in multi- access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker. |
| INT rcIpConfOspfV2Metric | 1.3.6.1.4.1.2272.1.8.1.9.1.4 | INTEGER | read-write | The metric for this type of service (TOS) on this interface. The default value of the TOS 0 Metric is (10^9 / ifSpeed). The value FFFF means 'no route via this TOS'. A value of 0 means the interface speed (rcIpConfOspfV2DefaultMetric) will be used as metric value, when the state of the interface is up. |
| STR rcIpConfOspfV2AuthKey | 1.3.6.1.4.1.2272.1.8.1.9.1.5 | DisplayString | read-write | The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. When read, ospfIfAuthKey always returns an Octet String of length zero. |
| ROW rcIpConfOspfV2RowStatus | 1.3.6.1.4.1.2272.1.8.1.9.1.6 | RowStatus | read-write | Row status for this entry. |
| INT rcIpConfOspfV2HelloInterval | 1.3.6.1.4.1.2272.1.8.1.9.1.7 | INTEGER | read-write | The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network. |
| INT rcIpConfOspfV2RtrDeadInterval | 1.3.6.1.4.1.2272.1.8.1.9.1.8 | INTEGER | read-write | The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network. |
| IP rcIpConfOspfV2IfAreaId | 1.3.6.1.4.1.2272.1.8.1.9.1.9 | IpAddress | read-write | A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone. |
| INT rcIpConfOspfV2AuthType | 1.3.6.1.4.1.2272.1.8.1.9.1.10 | INTEGER | read-write | The authentication type specified for an interface. Additional authentication types may be assigned locally. |
| rcIpConfOspfAreaAggregateTable | 1.3.6.1.4.1.2272.1.8.1.10 | not-accessible | A table used to maintain OSPF summary route metric parameter for a particular Area range. | |
| rcIpConfOspfAreaAggregateEntry | 1.3.6.1.4.1.2272.1.8.1.10.1 | not-accessible | Entry containing OSPF summary route metric parameter for a particular Area range. An entry is automatically created in this table when an area range is configured through ospfAreaAggregateTable in rfc1850rcc.mib | |
| IP rcIpConfOspfAreaAggregateAreaID | 1.3.6.1.4.1.2272.1.8.1.10.1.1 | IpAddress | read-only | The Area the Address Aggregate is to be found within. |
| INT rcIpConfOspfAreaAggregateLsdbType | 1.3.6.1.4.1.2272.1.8.1.10.1.2 | INTEGER | read-only | The type of the Address Aggregate. This field specifies the Lsdb type that this Address Ag- gregate applies to. |
| IP rcIpConfOspfAreaAggregateNet | 1.3.6.1.4.1.2272.1.8.1.10.1.3 | IpAddress | read-only | The IP Address of the Net or Subnet indicated by the range. |
| IP rcIpConfOspfAreaAggregateMask | 1.3.6.1.4.1.2272.1.8.1.10.1.4 | IpAddress | read-only | The Subnet Mask that pertains to the Net or Subnet. |
| INT rcIpConfOspfAreaAggregateAdvertiseMetric | 1.3.6.1.4.1.2272.1.8.1.10.1.5 | INTEGER | read-write | Used to specify a metric for a Summary LSA (type 3) generated by OSPF through an area range. If this metric is set to 0, OSPF uses the cost to the farthest point in the networks being summarized as the metric. |
| INT rcIpConfOspfAreaAggregateEffect | 1.3.6.1.4.1.2272.1.8.1.10.1.6 | INTEGER | read-write | Subnets subsumed by ranges either trigger the advertisement of the indicated aggregate (ad- vertiseMatching), or result in the subnet's not being advertised at all outside the area. |
| rcStatOspf | 1.3.6.1.4.1.2272.1.12.3 | |||
| C32 rcStatOspfBuffersAllocated | 1.3.6.1.4.1.2272.1.12.3.1 | Counter32 | read-only | Used to indicate the number of buffers allocated for OSPF. |
| C32 rcStatOspfBuffersFreed | 1.3.6.1.4.1.2272.1.12.3.2 | Counter32 | read-only | Used to indicate the number of buffers that are freed by the OSPF. |
| C32 rcStatOspfBufferAllocFailures | 1.3.6.1.4.1.2272.1.12.3.3 | Counter32 | read-only | Used to indicate the number of times that OSPF has failed to allocate buffers. |
| C32 rcStatOspfBufferFreeFailures | 1.3.6.1.4.1.2272.1.12.3.4 | Counter32 | read-only | Used to indicate the number of times that OSPF has failed to free buffers. |
| C32 rcStatOspfTxPackets | 1.3.6.1.4.1.2272.1.12.3.5 | Counter32 | read-only | Used to indicate the number of packets transmitted by OSPF. |
| C32 rcStatOspfRxPackets | 1.3.6.1.4.1.2272.1.12.3.6 | Counter32 | read-only | Used to indicate the number of packets received by OSPF. |
| C32 rcStatOspfTxDropPackets | 1.3.6.1.4.1.2272.1.12.3.7 | Counter32 | read-only | Used to indicate the number of packets dropped before transmitted by OSPF. |
| C32 rcStatOspfRxDropPackets | 1.3.6.1.4.1.2272.1.12.3.8 | Counter32 | read-only | Used to indicate the number of packets dropped before received by OSPF. |
| C32 rcStatOspfRxBadPackets | 1.3.6.1.4.1.2272.1.12.3.9 | Counter32 | read-only | Used to indicate the number of packets received by OSPF that are bad. |
| C32 rcStatOspfSpfRuns | 1.3.6.1.4.1.2272.1.12.3.10 | Counter32 | read-only | Used to indicate the total number of SPF calculatations performed by OSPF, which also includes the number of partial route table calculation for Incremental Updates. |
| TIK rcStatOspfLastSpfRun | 1.3.6.1.4.1.2272.1.12.3.11 | TimeTicks | read-only | Used to indicate the time(SysUpTime) since the last spf calculated by OSPF. |
| C32 rcStatOspfLsdbTblSize | 1.3.6.1.4.1.2272.1.12.3.12 | Counter32 | read-only | Used to indicate the number of entries in the linkstate database table. |
| C32 rcStatOspfRoutes | 1.3.6.1.4.1.2272.1.12.3.13 | Counter32 | read-only | Used to indicate the number of OSPF routes added to RTM. |
| C32 rcStatOspfAdjacencies | 1.3.6.1.4.1.2272.1.12.3.14 | Counter32 | read-only | Used to indicate the number of adjacencies existing. |
| C32 rcStatOspfAreas | 1.3.6.1.4.1.2272.1.12.3.15 | Counter32 | read-only | Used to indicate the number of areas configured |
| rcStatOspfIfTable | 1.3.6.1.4.1.2272.1.12.5 | not-accessible | A table used to store OSPF interface statistics. | |
| rcStatOspfIfEntry | 1.3.6.1.4.1.2272.1.12.5.1 | not-accessible | Ospf interface statistics | |
| NUM rcStatOspfIfIndex | 1.3.6.1.4.1.2272.1.12.5.1.1 | InterfaceIndexOrZero | read-only | An unique value that is used to identify a physical interface. |
| C32 rcStatOspfIfRxHellos | 1.3.6.1.4.1.2272.1.12.5.1.2 | Counter32 | read-only | Used to indicate the number hello packets received by this interface. |
| C32 rcStatOspfIfRxDBDescrs | 1.3.6.1.4.1.2272.1.12.5.1.3 | Counter32 | read-only | Used to indicate the number database descriptor packets received by this interface. |
| C32 rcStatOspfIfRxLSUpdates | 1.3.6.1.4.1.2272.1.12.5.1.4 | Counter32 | read-only | Used to indicate the number Link state update packets received by this interface. |
| C32 rcStatOspfIfRxLSReqs | 1.3.6.1.4.1.2272.1.12.5.1.5 | Counter32 | read-only | Used to indicate the number Link state request packets received by this interface. |
| C32 rcStatOspfIfRxLSAcks | 1.3.6.1.4.1.2272.1.12.5.1.6 | Counter32 | read-only | Used to indicate the number Link state acknowlege packets received by this interface. |
| C32 rcStatOspfIfTxHellos | 1.3.6.1.4.1.2272.1.12.5.1.7 | Counter32 | read-only | Used to indicate the number hello packets transmitted by this interface. |
| C32 rcStatOspfIfTxDBDescrs | 1.3.6.1.4.1.2272.1.12.5.1.8 | Counter32 | read-only | Used to indicate the number database descriptor packets transmitted by this interface. |
| C32 rcStatOspfIfTxLSUpdates | 1.3.6.1.4.1.2272.1.12.5.1.9 | Counter32 | read-only | Used to indicate the number Link state update packets transmitted by this interface. |
| C32 rcStatOspfIfTxLSReqs | 1.3.6.1.4.1.2272.1.12.5.1.10 | Counter32 | read-only | Used to indicate the number Link state request packets transmitted by this interface. |
| C32 rcStatOspfIfTxLSAcks | 1.3.6.1.4.1.2272.1.12.5.1.11 | Counter32 | read-only | Used to indicate the number Link state acknowlege packets transmitted by this interface. |
| C32 rcStatOspfIfVersionMismatches | 1.3.6.1.4.1.2272.1.12.5.1.12 | Counter32 | read-only | Used to indicate the number version mismatches received by this interface. |
| C32 rcStatOspfIfAreaMismatches | 1.3.6.1.4.1.2272.1.12.5.1.13 | Counter32 | read-only | Used to indicate the number area mismatches received by this interface. |
| C32 rcStatOspfIfAuthTypeMismatches | 1.3.6.1.4.1.2272.1.12.5.1.14 | Counter32 | read-only | Used to indicate the number AuthType mismatches received by this interface. |
| C32 rcStatOspfIfAuthFailures | 1.3.6.1.4.1.2272.1.12.5.1.15 | Counter32 | read-only | Used to indicate the number Authentication failures. |
| C32 rcStatOspfIfNetMaskMismatches | 1.3.6.1.4.1.2272.1.12.5.1.16 | Counter32 | read-only | Used to indicate the number net mask mismatches received by this interface. |
| C32 rcStatOspfIfHelloIntervalMismatches | 1.3.6.1.4.1.2272.1.12.5.1.17 | Counter32 | read-only | Used to indicate the number hello interval mismatches received by this interface. |
| C32 rcStatOspfIfDeadIntervalMismatches | 1.3.6.1.4.1.2272.1.12.5.1.18 | Counter32 | read-only | Used to indicate the number dead interval mismatches received by this interface. |
| C32 rcStatOspfIfOptionMismatches | 1.3.6.1.4.1.2272.1.12.5.1.19 | Counter32 | read-only | Used to indicate the number options mismatches received by this interface. |
| rcStatOspfIfV2Table | 1.3.6.1.4.1.2272.1.12.7 | not-accessible | A table used to store OSPF interface statistics. | |
| rcStatOspfIfV2Entry | 1.3.6.1.4.1.2272.1.12.7.1 | not-accessible | Ospf interface statistics | |
| NUM rcStatOspfIfV2Index | 1.3.6.1.4.1.2272.1.12.7.1.1 | InterfaceIndexOrZero | read-only | An unique value that is used to identify a physical interface. |
| IP rcStatOspfIfV2Addr | 1.3.6.1.4.1.2272.1.12.7.1.2 | IpAddress | read-only | Ip Address |
| C32 rcStatOspfIfV2RxHellos | 1.3.6.1.4.1.2272.1.12.7.1.3 | Counter32 | read-only | Used to indicate the number hello packets received by this interface. |
| C32 rcStatOspfIfV2RxDBDescrs | 1.3.6.1.4.1.2272.1.12.7.1.4 | Counter32 | read-only | Used to indicate the number database descriptor packets received by this interface. |
| C32 rcStatOspfIfV2RxLSUpdates | 1.3.6.1.4.1.2272.1.12.7.1.5 | Counter32 | read-only | Used to indicate the number Link state update packets received by this interface. |
| C32 rcStatOspfIfV2RxLSReqs | 1.3.6.1.4.1.2272.1.12.7.1.6 | Counter32 | read-only | Used to indicate the number Link state request packets received by this interface. |
| C32 rcStatOspfIfV2RxLSAcks | 1.3.6.1.4.1.2272.1.12.7.1.7 | Counter32 | read-only | Used to indicate the number Link state acknowlege packets received by this interface. |
| C32 rcStatOspfIfV2TxHellos | 1.3.6.1.4.1.2272.1.12.7.1.8 | Counter32 | read-only | Used to indicate the number hello packets transmitted by this interface. |
| C32 rcStatOspfIfV2TxDBDescrs | 1.3.6.1.4.1.2272.1.12.7.1.9 | Counter32 | read-only | Used to indicate the number database descriptor packets transmitted by this interface. |
| C32 rcStatOspfIfV2TxLSUpdates | 1.3.6.1.4.1.2272.1.12.7.1.10 | Counter32 | read-only | Used to indicate the number Link state update packets transmitted by this interface. |
| C32 rcStatOspfIfV2TxLSReqs | 1.3.6.1.4.1.2272.1.12.7.1.11 | Counter32 | read-only | Used to indicate the number Link state request packets transmitted by this interface. |
| C32 rcStatOspfIfV2TxLSAcks | 1.3.6.1.4.1.2272.1.12.7.1.12 | Counter32 | read-only | Used to indicate the number Link state acknowlege packets transmitted by this interface. |
| C32 rcStatOspfIfV2VersionMismatches | 1.3.6.1.4.1.2272.1.12.7.1.13 | Counter32 | read-only | Used to indicate the number version mismatches received by this interface. |
| C32 rcStatOspfIfV2AreaMismatches | 1.3.6.1.4.1.2272.1.12.7.1.14 | Counter32 | read-only | Used to indicate the number area mismatches received by this interface. |
| C32 rcStatOspfIfV2AuthTypeMismatches | 1.3.6.1.4.1.2272.1.12.7.1.15 | Counter32 | read-only | Used to indicate the number AuthType mismatches received by this interface. |
| C32 rcStatOspfIfV2AuthFailures | 1.3.6.1.4.1.2272.1.12.7.1.16 | Counter32 | read-only | Used to indicate the number Authentication failures. |
| C32 rcStatOspfIfV2NetMaskMismatches | 1.3.6.1.4.1.2272.1.12.7.1.17 | Counter32 | read-only | Used to indicate the number net mask mismatches received by this interface. |
| C32 rcStatOspfIfV2HelloIntervalMismatches | 1.3.6.1.4.1.2272.1.12.7.1.18 | Counter32 | read-only | Used to indicate the number hello interval mismatches received by this interface. |
| C32 rcStatOspfIfV2DeadIntervalMismatches | 1.3.6.1.4.1.2272.1.12.7.1.19 | Counter32 | read-only | Used to indicate the number dead interval mismatches received by this interface. |
| C32 rcStatOspfIfV2OptionMismatches | 1.3.6.1.4.1.2272.1.12.7.1.20 | Counter32 | read-only | Used to indicate the number options mismatches received by this interface. |
| rcOspfMib | 1.3.6.1.4.1.8886.6.1.18.1 | Enterprise MIB for the Accelar product family. |
RFC description
Vendor-private MIB for OSPF (Open Shortest Path First) routing protocol management; provides monitoring and configuration of OSPF-enabled network devices.
Start monitoring Nortel Accelar / Ethernet Routing Switch (ERS) (per-interface OSPF configuration with BFD integration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.