RAD-SONET-MIB

All MIBs › RAD-SONET-MIB

Category: SONET and SDH

Description: Manages RAD Data Communications SONET/SDH interface configuration, overhead parameters, and performance statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RAD-SONET-MIB?

This is a RAD Data Communications proprietary MIB that manages SONET/SDH interface configuration and reports detailed performance and defect statistics for RAD transport equipment. Its data spans SONET medium/section/line configuration and current/history performance counters, plus explicit defect indicators for common SONET fault conditions. It is used heavily to monitor the hardware/line status of a SONET interface — objects like prtSonetCurrentLOS, prtSonetCurrentLOF, prtSonetCurrentLineAIS, prtSonetCurrentLineFERF, and the BIP error counters (prtSonetCurrentSectionBIP/prtSonetCurrentLineBIP) let an operator detect loss of signal, loss of frame, alarm-indication signal, far-end failures, or bit-error-rate degradation on the fiber link in near real time. It extends the standard SONET-MIB (RFC 3592/2558) with RAD-specific medium and performance-history objects, so it depends on that IETF standard for its base interface model. It is deployed on RAD Data Communications SONET/SDH transport and access equipment used by carriers and enterprises to terminate or groom SONET/SDH circuits. Engineers can download the RAD-SONET-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in RAD-SONET-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

RAD Data Communications SONET/SDH transport device

Monitoring Examples

An operator polls prtSonetMediumTable/prtSonetMediumEntry to check prtSonetMediumValidIntervals and then examines prtSonetSectionLineCurrentTable/prtSectionLineCurrentEntry for prtSonetCurrentLOS, prtSonetCurrentLOF, prtSonetCurrentLineAIS, and prtSonetCurrentLineFERF to detect an active signal or frame-loss condition on the SONET line. Rising prtSonetCurrentSectionBIP/prtSonetCurrentLineBIP error counts alongside prtSonetPerfHistory data would indicate a degrading fiber or optics problem well before a hard failure occurs.

What Can Be Monitored

loss of signal (LOS)
loss of frame (LOF)
line alarm indication signal (AIS)
far-end receive failure (FERF)
section/line BIP error counts
SONET performance history

Imported Objects

From IF-MIB

InterfaceIndex

From PerfHist-TC-MIB

PerfCurrentCount
PerfIntervalCount

From RAD-MIB

diverseIfWanGen

OBJECT-IDENTITY

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Counter64
Gauge32
Integer32
IpAddress
OBJECT-TYPE

From SNMPv2-TC

DisplayString
RowStatus

How to Use in IPNetwork Monitor

Example using virtualIfCurrentRxFrames OID:

Select an RAD Data Communications SONET/SDH transport device as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type virtualIfCurrentRxFrames into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This counter is associated with the number of frames received from STS-3/STM-1 by a Virtual Interface in the current 15-minute interval. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
sonetInterface	1.3.6.1.4.1.164.3.1.6.2
prtSonetPerfHistory	1.3.6.1.4.1.164.3.1.6.2.1
prtSonetMediumTable	1.3.6.1.4.1.164.3.1.6.2.1.1		not-accessible	The SONET Medium table.
prtSonetMediumEntry	1.3.6.1.4.1.164.3.1.6.2.1.1.1		not-accessible	An entry in the SONET Medium table. ifIndex of the lowest SONET layer of type sonet(39).
I32 prtSonetMediumTimeElapsed	1.3.6.1.4.1.164.3.1.6.2.1.1.1.1	Integer32	read-only	The number of seconds that have elapsed since the beginning of the near end current error- measurement period.
I32 prtSonetMediumValidIntervals	1.3.6.1.4.1.164.3.1.6.2.1.1.1.2	Integer32	read-only	The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute near end intervals since the interface has been online.
prtSonetSectionLineCurrentTable	1.3.6.1.4.1.164.3.1.6.2.1.2		not-accessible	The SONET Section/Line Current table.
prtSectionLineCurrentEntry	1.3.6.1.4.1.164.3.1.6.2.1.2.1		not-accessible	An entry in the SONET Section/Line Current table. ifIndex of the section/line SONET layer of type sonet(39).
G32 prtSonetCurrentLOS	1.3.6.1.4.1.164.3.1.6.2.1.2.1.1	Gauge32	read-only	The counter associated with the number of LOS seconds, encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentLOF	1.3.6.1.4.1.164.3.1.6.2.1.2.1.2	Gauge32	read-only	The counter associated with the number of LOF seconds, encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentLineAIS	1.3.6.1.4.1.164.3.1.6.2.1.2.1.3	Gauge32	read-only	The counter associated with the number of Line AIS seconds, encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentLineFERF	1.3.6.1.4.1.164.3.1.6.2.1.2.1.4	Gauge32	read-only	The counter associated with the number of Line FERF seconds, encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentSectionBIP	1.3.6.1.4.1.164.3.1.6.2.1.2.1.5	Gauge32	read-only	The counter associated with the number of Section BIP errors, encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentLineBIP	1.3.6.1.4.1.164.3.1.6.2.1.2.1.6	Gauge32	read-only	The counter associated with the number of Line BIP errors, encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentLineFEBE	1.3.6.1.4.1.164.3.1.6.2.1.2.1.7	Gauge32	read-only	The counter associated with the number of Line FEBE errors, encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentUAS	1.3.6.1.4.1.164.3.1.6.2.1.2.1.8	Gauge32	read-only	The counter associated with the number of UAS encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentSES	1.3.6.1.4.1.164.3.1.6.2.1.2.1.9	Gauge32	read-only	The counter associated with the number of SES encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentES	1.3.6.1.4.1.164.3.1.6.2.1.2.1.10	Gauge32	read-only	The number of Errored Seconds, encountered by a SONET interface in the current 15 minute interval.
OCT prtSonetCurrentStatus	1.3.6.1.4.1.164.3.1.6.2.1.2.1.11	OCTET STRING	read-only	The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out.
G32 prtSonetCurrentLSV	1.3.6.1.4.1.164.3.1.6.2.1.2.1.12	Gauge32	read-only	The counter associated with the number of LSV seconds (Line Symbol Violation), encountered by a SONET interface in the current 15 minute interval.
prtSonetSectionLineIntervalTable	1.3.6.1.4.1.164.3.1.6.2.1.3		not-accessible	The Section/Line Interval table.
prtSectionLineIntervalEntry	1.3.6.1.4.1.164.3.1.6.2.1.3.1		not-accessible	An entry in the SONET Section/Line Interval table. ifIndex of the section/line SONET layer of type sonet(39).
I32 prtSonetLineIntervalNumber	1.3.6.1.4.1.164.3.1.6.2.1.3.1.1	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 prtSonetIntervalLOS	1.3.6.1.4.1.164.3.1.6.2.1.3.1.2	Gauge32	read-only	The counter associated with the number of LOS seconds , encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalLOF	1.3.6.1.4.1.164.3.1.6.2.1.3.1.3	Gauge32	read-only	The counter associated with the number of LOF seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalLineAIS	1.3.6.1.4.1.164.3.1.6.2.1.3.1.4	Gauge32	read-only	The counter associated with the number of Line AIS seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalLineFERF	1.3.6.1.4.1.164.3.1.6.2.1.3.1.5	Gauge32	read-only	The counter associated with the number of Line FERF seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalSectionBIP	1.3.6.1.4.1.164.3.1.6.2.1.3.1.6	Gauge32	read-only	The counter associated with the number of Section BIP errors, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalLineBIP	1.3.6.1.4.1.164.3.1.6.2.1.3.1.7	Gauge32	read-only	The counter associated with the number of Line BIP errors, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalLineFEBE	1.3.6.1.4.1.164.3.1.6.2.1.3.1.8	Gauge32	read-only	The counter associated with the number of Line FEBE errors, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalUAS	1.3.6.1.4.1.164.3.1.6.2.1.3.1.9	Gauge32	read-only	The counter associated with the number of UAS encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalSES	1.3.6.1.4.1.164.3.1.6.2.1.3.1.10	Gauge32	read-only	The counter associated with the number of SES encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalES	1.3.6.1.4.1.164.3.1.6.2.1.3.1.11	Gauge32	read-only	The number of Errored Seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
OCT prtSonetIntervalStatus	1.3.6.1.4.1.164.3.1.6.2.1.3.1.12	OCTET STRING	read-only	The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out.
G32 prtSonetIntervalLSV	1.3.6.1.4.1.164.3.1.6.2.1.3.1.13	Gauge32	read-only	The counter associated with the number of LSV seconds (Line Symbol Violation), encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
prtSonetPathCurrentTable	1.3.6.1.4.1.164.3.1.6.2.1.4		not-accessible	The SONET Path Current table.
prtPathCurrentEntry	1.3.6.1.4.1.164.3.1.6.2.1.4.1		not-accessible	An entry in the SONET Path Current table. ifIndex of the Path SONET layer of type sonetPath(50).
G32 prtSonetCurrentPathAIS	1.3.6.1.4.1.164.3.1.6.2.1.4.1.1	Gauge32	read-only	The counter associated with the number of Path AIS seconds, encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentPathFERF	1.3.6.1.4.1.164.3.1.6.2.1.4.1.2	Gauge32	read-only	The counter associated with the number of Path FERF seconds, encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentLOP	1.3.6.1.4.1.164.3.1.6.2.1.4.1.3	Gauge32	read-only	The counter associated with the number LOP seconds, encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentSLM	1.3.6.1.4.1.164.3.1.6.2.1.4.1.4	Gauge32	read-only	The counter associated with the number of SLM seconds, encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentLOC	1.3.6.1.4.1.164.3.1.6.2.1.4.1.5	Gauge32	read-only	The counter associated with the number of LOC seconds, encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentPathBIP	1.3.6.1.4.1.164.3.1.6.2.1.4.1.6	Gauge32	read-only	The counter associated with the number of Path BIP errors, encountered by a SONET interface in the current 15 minute interval.
G32 prtSonetCurrentPathFEBE	1.3.6.1.4.1.164.3.1.6.2.1.4.1.7	Gauge32	read-only	The counter associated with the number of Path FEBE errors, encountered by a SONET interface in the current 15 minute interval.
prtSonetPathIntervalTable	1.3.6.1.4.1.164.3.1.6.2.1.5		not-accessible	The Path Interval table.
prtPathIntervalEntry	1.3.6.1.4.1.164.3.1.6.2.1.5.1		not-accessible	An entry in the SONET Path Interval table.
I32 prtSonetPathIntervalNumber	1.3.6.1.4.1.164.3.1.6.2.1.5.1.1	Integer32	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
G32 prtSonetIntervalPathAIS	1.3.6.1.4.1.164.3.1.6.2.1.5.1.2	Gauge32	read-only	The counter associated with the number of Path AIS seconds , encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalPathFERF	1.3.6.1.4.1.164.3.1.6.2.1.5.1.3	Gauge32	read-only	The counter associated with the number of Path FERF seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalLOP	1.3.6.1.4.1.164.3.1.6.2.1.5.1.4	Gauge32	read-only	The counter associated with the number of LOP seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalSLM	1.3.6.1.4.1.164.3.1.6.2.1.5.1.5	Gauge32	read-only	The counter associated with the number of SLM seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalLOC	1.3.6.1.4.1.164.3.1.6.2.1.5.1.6	Gauge32	read-only	The counter associated with the number of LOC seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalPathBIP	1.3.6.1.4.1.164.3.1.6.2.1.5.1.7	Gauge32	read-only	The counter associated with the number of Path BIP errors, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
G32 prtSonetIntervalPathFEBE	1.3.6.1.4.1.164.3.1.6.2.1.5.1.8	Gauge32	read-only	The counter associated with the number of Path FEBE errors, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.
virtualIfStatistics	1.3.6.1.4.1.164.3.1.6.2.1.6
virtualIfCurrentTable	1.3.6.1.4.1.164.3.1.6.2.1.6.1		not-accessible	The Virtual Interface Current table.
virtualIfCurrentEntry	1.3.6.1.4.1.164.3.1.6.2.1.6.1.1		not-accessible	An entry in the Virtual Interface Current table.
I32 virtualIfCurrentMinActiveVC	1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.1	Integer32	read-only	This object holds the minimum number of active virtual containers (VCs) of the Virtual Concatenation Group in the current 15-minute interval.
I32 virtualIfCurrentMaxActiveVC	1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.2	Integer32	read-only	This object holds the maximum number of active virtual containers (VCs) of the Virtual Concatenation Group in the current 15-minute interval.
C64 virtualIfCurrentRxFramesEx	1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.3	Counter64	read-only	This counter is associated with the number of frames received from STS-3/STM-1 by a Virtual Interface in the current 15-minute interval.
C64 virtualIfCurrentTxFrames	1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.4	Counter64	read-only	This counter is associated with the number of frames transmitted to STS-3/STM-1 by a Virtual Interface in the current 15-minute interval.
PER virtualIfCurrentRxAbortFrames	1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.5	PerfCurrentCount	read-only	The counter associated with the number of Received Aborted frames encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfCurrentTxAbortFrames	1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.6	PerfCurrentCount	read-only	The counter associated with the number of Transmitted Aborted frames encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfCurrentMinLengthViolation	1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.7	PerfCurrentCount	read-only	This counter is associated with the number of Rx payload Min Length Violation frames encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfCurrentMaxLengthViolation	1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.8	PerfCurrentCount	read-only	This counter is associated with the number of Rx payload Max Length Violation frames encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfCurrentFcsError	1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.9	PerfCurrentCount	read-only	The counter is associated with the number of Frame Check Sequence errors encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfCurrentByteDestuffingViolation	1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.10	PerfCurrentCount	read-only	The counter associated with the number of Byte De-stuffing Violations encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfCurrentAdressMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.11	PerfCurrentCount	read-only	The counter associated with the number of Adress Mismatch encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfCurrentControlMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.12	PerfCurrentCount	read-only	The counter associated with the number of Control Mismatch encountered by a Virtual Interface in the current 15-minute interval.
I32 virtualIfCurrentActiveVC	1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.13	Integer32	read-only	This object holds the number of active virtual containers (VCs) of the Virtual Concatenation Group in the current 15-minute interval.
virtualIfIntervalTable	1.3.6.1.4.1.164.3.1.6.2.1.6.2		not-accessible	The Virtual Interface Interval table.
virtualIfIntervalEntry	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1		not-accessible	An entry in the Virtual Interface Interval table.
I32 virtualIfIntervalNumber	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.1	Integer32	not-accessible	A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
I32 virtualIfIntervalMinActiveVC	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.2	Integer32	read-only	This object holds the minimum number of active virtual containers (VCs) of the Virtual Concatenation Group, in a particular 15-minute interval in the past 24 hours.
I32 virtualIfIntervalMaxActiveVC	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.3	Integer32	read-only	This object holds the maximum number of active virtual containers (VCs) of the Virtual Concatenation Group, in a particular 15-minute interval in the past 24 hours.
C64 virtualIfIntervalRxFrames	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.4	Counter64	read-only	This counter is associated with the number of frames received from STS-3/STM-1 by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
C64 virtualIfIntervalTxFrames	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.5	Counter64	read-only	This counter is associated with the number of frames transmitted to STS-3/STM-1 by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfIntervalRxAbortFrames	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.6	PerfIntervalCount	read-only	This counter is associated with the number of Received Abort frames encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfIntervalTxAbortFrames	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.7	PerfIntervalCount	read-only	This counter is associated with the number of Transmitted Abort frames encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfIntervalMinLengthViolation	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.8	PerfIntervalCount	read-only	This counter is associated with the number of Rx payload Min Length Violation frames encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfIntervalMaxLengthViolation	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.9	PerfIntervalCount	read-only	This counter is associated with the number of Rx payload Max Length Violation frames encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfIntervalFcsError	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.10	PerfIntervalCount	read-only	This counter is associated with the number of Frame Check Sequence errors encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfIntervalByteDestuffingViolation	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.11	PerfIntervalCount	read-only	This counter is associated with the number of Byte De-stuffing Violations encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfIntervalAdressMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.12	PerfIntervalCount	read-only	This counter is associated with the number of Address Mismatch encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfIntervalControlMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.13	PerfIntervalCount	read-only	This counter is associated with the number of Control mismatch encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfIntervalBelowMinThreshold	1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.14	PerfIntervalCount	read-only	This counter is associated with the number of seconds that number of active VCs was below minimum threshold defined by vcGroupCnfgNoOfVCs, encountered by Virtual Interface in a particular 15-minute interval in the past 24 hours.
virtualIfLAPSCurrentTable	1.3.6.1.4.1.164.3.1.6.2.1.6.3		not-accessible	The Virtual Interface LAPS Current table.
virtualIfLAPSCurrentEntry	1.3.6.1.4.1.164.3.1.6.2.1.6.3.1		not-accessible	An entry in the Virtual Interface LAPS Current table.
PER virtualIfLAPSCurrentSapiMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.3.1.1	PerfCurrentCount	read-only	This counter is associated with the number of received SAPI field mismatch encountered by a Virtual Interface in the current 15-minute interval.
virtualIfLAPSIntervalTable	1.3.6.1.4.1.164.3.1.6.2.1.6.4		not-accessible	The Virtual Interface LAPS table.
virtualIfLAPSIntervalEntry	1.3.6.1.4.1.164.3.1.6.2.1.6.4.1		not-accessible	An entry in the Virtual Interface LAPS Interval table.
NUM virtualIfLAPSIntervalSapiMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.4.1.1	PerfIntervalCount	read-only	This counter is associated with the number of received SAPI field mismatch encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
virtualIfLAPFCurrentTable	1.3.6.1.4.1.164.3.1.6.2.1.6.5		not-accessible	The Virtual Interface LAPF Current table.
virtualIfLAPFCurrentEntry	1.3.6.1.4.1.164.3.1.6.2.1.6.5.1		not-accessible	An entry in the Virtual Interface LAPF Current table.
PER virtualIfLAPFCurrentNlpidMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.1	PerfCurrentCount	read-only	This counter is associated with the number of received NLPID field mismatch encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfLAPFCurrentOuiMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.2	PerfCurrentCount	read-only	This counter is associated with the number of received OUI field mismatch encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfLAPFCurrentPidMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.3	PerfCurrentCount	read-only	This counter is associated with the number of received PID field mismatch encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfLAPFCurrentDlciMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.4	PerfCurrentCount	read-only	This counter is associated with the number of received DLCI field mismatch encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfLAPFCurrentMacRxFrames	1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.5	PerfCurrentCount	read-only	This counter is associated with the number of frames received from LAN by a Virtual Interface in the current 15-minute interval.
PER virtualIfLAPFCurrentMacTxFrames	1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.6	PerfCurrentCount	read-only	This counter is associated with the number of frames transmitted to LAN by a Virtual Interface in the current 15-minute interval.
virtualIfLAPFIntervalTable	1.3.6.1.4.1.164.3.1.6.2.1.6.6		not-accessible	The Virtual Interface LAPF Interval table.
virtualIfLAPFIntervalEntry	1.3.6.1.4.1.164.3.1.6.2.1.6.6.1		not-accessible	An entry in the Virtual Interface Interval table.
NUM virtualIfLAPFIntervalNlpidMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.1	PerfIntervalCount	read-only	This counter is associated with the number of received NLPID field mismatch encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfLAPFIntervalOuiMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.2	PerfIntervalCount	read-only	This counter is associated with the number of received OUI field mismatch encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfLAPFIntervalPidMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.3	PerfIntervalCount	read-only	This counter is associated with the number of received PID field mismatch encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfLAPFIntervalDlciMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.4	PerfIntervalCount	read-only	This counter is associated with the number of received DLCI field mismatch by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfLAPFIntervalMacRxFrames	1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.5	PerfIntervalCount	read-only	This counter is associated with the number of frames received from LAN by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfLAPFIntervalMacTxFrames	1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.6	PerfIntervalCount	read-only	This counter is associated with the number of frames transmitted to LAN encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
virtualIfGFPCurrentTable	1.3.6.1.4.1.164.3.1.6.2.1.6.7		not-accessible	The Virtual Interface GFP Current table.
virtualIfGFPCurrentEntry	1.3.6.1.4.1.164.3.1.6.2.1.6.7.1		not-accessible	An entry in the Virtual Interface GFP Current table.
PER virtualIfGFPCurrentIdleFrameError	1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.1	PerfCurrentCount	read-only	This counter is associated with the number of received GFP IDLE frames that are detected to be in error, encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfGFPCurrentCHecSbError	1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.2	PerfCurrentCount	read-only	This counter is associated with the number of received GFP frames that are detected to have single-bit errors in the Core header (i.e. cHEC field) only, encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfGFPCurrentPtiMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.3	PerfCurrentCount	read-only	This counter is associated with the number of rreceived GFP frames that are detected with a mismatch on the PTI field (i.e. value of PTI is not equal to Client Data or Management frame), encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfGFPCurrentExiMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.4	PerfCurrentCount	read-only	This counter is associated with the number of received GFP frames that are detected with a mismatch on the EXI field (i.e. value of EXI is not equal to NULL or LINEAR modes), encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfGFPCurrentUpiMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.5	PerfCurrentCount	read-only	This counter is associated with the number of received GFP frames that are detected with a mismatch on the UPI field (i.e. value of EXI is not equal to 00000001), encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfGFPCurrentTHecSbError	1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.6	PerfCurrentCount	read-only	This counter is associated with the number of received GFP frames that are detected to only have single-bit errors in the Type header (i.e. tHEC field), encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfGFPCurrentTHecMbError	1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.7	PerfCurrentCount	read-only	This counter is associated with the number of received GFP frames that are detected to only have multi-bit errors in the Type header (i.e. tHEC field), encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfGFPCurrentCidMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.8	PerfCurrentCount	read-only	This counter is associated with the number of received GFP frames that are detected to have a mismatch/unsupported value in the CID field only, encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfGFPCurrentEHecSbError	1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.9	PerfCurrentCount	read-only	This counter is associated with the number of received GFP frames that are detected to only have single-bit errors in the Extension header (i.e. eHEC field), encountered by a Virtual Interface in the current 15-minute interval.
PER virtualIfGFPCurrentEHecMbError	1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.10	PerfCurrentCount	read-only	This counter is associated with the number of received GFP frames that are detected to only have single-bit errors in the Extension header (i.e. eHEC field), encountered by a Virtual Interface in the current 15-minute interval.
virtualIfGFPIntervalTable	1.3.6.1.4.1.164.3.1.6.2.1.6.8		not-accessible	The Virtual Interface GFP Interval table.
virtualIfGFPIntervalEntry	1.3.6.1.4.1.164.3.1.6.2.1.6.8.1		not-accessible	An entry in the Virtual Interface GFP Interval table.
NUM virtualIfGFPIntervalIdleFrameError	1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.1	PerfIntervalCount	read-only	This counter is associated with the number of received GFP IDLE frames that are detected to be in error, encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfGFPIntervalCHecSbError	1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.2	PerfIntervalCount	read-only	This counter is associated with the number of received GFP frames that are detected to have single-bit errors in the Core header (i.e. cHEC field) only, encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfGFPIntervalPtiMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.3	PerfIntervalCount	read-only	This counter is associated with the number of rreceived GFP frames that are detected with a mismatch on the PTI field (i.e. value of PTI is not equal to Client Data or Management frame), encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfGFPIntervalExiMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.4	PerfIntervalCount	read-only	This counter is associated with the number of received GFP frames that are detected with a mismatch on the EXI field (i.e. value of EXI is not equal to NULL or LINEAR modes), encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfGFPIntervalUpiMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.5	PerfIntervalCount	read-only	This counter is associated with the number of received GFP frames that are detected with a mismatch on the UPI field (i.e. value of EXI is not equal to 00000001), encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfGFPIntervalTHecSbError	1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.6	PerfIntervalCount	read-only	This counter is associated with the number of received GFP frames that are detected to only have single-bit errors in the Type header (i.e. tHEC field), encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfGFPIntervalTHecMbError	1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.7	PerfIntervalCount	read-only	This counter is associated withthe number of received GFP frames that are detected to only have multi-bit errors in the Type header (i.e. tHEC field), encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfGFPIntervalCidMismatch	1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.8	PerfIntervalCount	read-only	This counter is associated with the number of received GFP frames that are detected to have a mismatch/unsupported value in the CID field only, encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfGFPIntervalEHecSbError	1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.9	PerfIntervalCount	read-only	This counter is associated with the number of received GFP frames that are detected to only have single-bit errors in the Extension header (i.e. eHEC field), encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
NUM virtualIfGFPIntervalEHecMbError	1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.10	PerfIntervalCount	read-only	This counter is associated with the the number of received GFP frames that are detected to only have multi-bit errors in the Extension header (i.e. eHEC field), encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.
prtSonetConfig	1.3.6.1.4.1.164.3.1.6.2.2
prtSonetGen	1.3.6.1.4.1.164.3.1.6.2.2.1
prtSonetGenTable	1.3.6.1.4.1.164.3.1.6.2.2.1.1		not-accessible	Sonet/SDH general port configuration table.
prtSonetGenEntry	1.3.6.1.4.1.164.3.1.6.2.2.1.1.1		not-accessible	An entry in the Sonet/SDH general port configuration table.
I32 prtSonetGenCnfgIdx	1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.1	Integer32	read-only	This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255).
I32 prtSonetGenIdx	1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.2	Integer32	read-only	This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex.
INT prtSonetGenSdThreshold	1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.3	INTEGER	read-write	SD=Signal Degraded Threshold. Units: [10E-]. The threshold is 10E-x relative to the frequency of the data flow. x=3, 4, 5, 6, 7, 8, 9. n3= 10E-3 n4= 10E-4 n5= 10E-5 n6= 10E-6 n7= 10E-7 n8= 10E-8 n9= 10E-9 .
INT prtSonetGenEedThreshold	1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.4	INTEGER	read-write	EED=Excessive Error Defect Threshold. Units: [10E-]. The threshold is 10E-x relative to the frequency of the data flow. x=3, 4, 5, 6, 7, 8, 9. n3= 10E-3 n4= 10E-4 n5= 10E-5 n6= 10E-6 n7= 10E-7 n8= 10E-8 n9= 10E-9 .
INT prtSonetGenBerEnable	1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.5	INTEGER	read-write	Controls the activation of the Line Ber (Bit Error Rate), means whether SD and EED threshold parameters will be enabled.
prtSonetStm1	1.3.6.1.4.1.164.3.1.6.2.2.2
prtSonetStm1Table	1.3.6.1.4.1.164.3.1.6.2.2.2.1		not-accessible	Sonet/SDH STM-1 port configuration table.
prtSonetStm1Entry	1.3.6.1.4.1.164.3.1.6.2.2.2.1.1		not-accessible	An entry in the Sonet/SDH STM-1 port configuration table.
I32 prtSonetStm1CnfgIdx	1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.1	Integer32	read-only	This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255).
I32 prtSonetStm1Idx	1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.2	Integer32	read-only	This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex.
INT prtSonetStm1ClockSrc	1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.3	INTEGER	read-write	Clock Source of the STM-1 port. lbt = Loop Back Timing.
INT prtSonetStm1DccMode	1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.4	INTEGER	read-write	DCC Mode. DCC=Data Communication Channel. d1ToD3 = D1-D3 bytes are used (RS=Regeneration Section). d4ToD12= D4-D12 bytes are used (MS=Multiplexing Section). d1.... d12 enable user to select single DCC byte
INT prtSonetStm1RoutingProt	1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.5	INTEGER	read-write	Routing Protocol.
INT prtSonetStm1MngProt	1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.6	INTEGER	read-write	Management Protocol over DCC: Proprietary, PPP, Frame Relay, HDLC or LAPD over HDLC . ppp = according to STD-51 ( rfc1661/1662) pppType1= ppp without sendind ADD CONTROL overhead in Link Control Protocol (LCP) packets
INT prtSonetStm1OperationalMode	1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.7	INTEGER	read-write	Operational Mode. linear - cannot be selected when there is Redundancy between the STM-1 ports.
INT prtSonetStm1VoiceChannel	1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.8	INTEGER	read-write	This parameter enable user to select whether voice channel will be transferred using E1 byte, E2 Byte, or not at all.
I32 prtSonetStm1OutputRate	1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.9	Integer32	read-write	This parameter indicates the output rate in cells/sec, which is supported per port.
INT prtSonetStm1S1ProtocolClock	1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.10	INTEGER	read-write	This parameter allows user to select whether to enable use of Remote Side Clock according to the Protocol passed on S1 Bit.
IP prtSonetStm1GatewayRingSubnetAddress	1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.11	IpAddress	read-write	This parameter defines subnet for static routing, together with prtSonetStm1GatewayRingSubnetMask
IP prtSonetStm1GatewayRingSubnetMask	1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.12	IpAddress	read-write	This parameter defines subnet for static routing, together with prtSonetStm1GatewayRingSubnetAddress
INT prtSonetStm1MngProtDeviationType	1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.13	INTEGER	read-write	This parameter is used in conjunction with prtSonetStm1MngProt to define management protocol used & type of deviation (if exist) from standard. Standard = no deviation from standard protocol Type1 = PPP without sending Address and Control overhead in Link Control Protocol (LCP) packets
prtSonetVc	1.3.6.1.4.1.164.3.1.6.2.2.3
prtSonetVcTable	1.3.6.1.4.1.164.3.1.6.2.2.3.1		not-accessible	Sonet/SDH VC port configuration table.
prtSonetVcEntry	1.3.6.1.4.1.164.3.1.6.2.2.3.1.1		not-accessible	An entry in the Sonet/SDH VC port configuration table.
I32 prtSonetVcCnfgIdx	1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.1	Integer32	read-only	This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255).
I32 prtSonetVcIdx	1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.2	Integer32	read-only	This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex.
INT prtSonetVcJTxPathTraceEnable	1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.3	INTEGER	read-write	Enable/Disable Transmitting Jy Path Trace. y=1, 2: J1 - for VC-4 layer J2 - for VC-12 layer.
INT prtSonetVcJRxPathTraceEnable	1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.4	INTEGER	read-write	Enable/Disable checking Jy Path Trace. y=1, 2: J1 - for VC-4 layer J2 - for VC-12 layer.
STR prtSonetVcJPathTrace	1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.5	DisplayString	read-write	Jy Path Trace. y=1, 2: J1 - for VC-4 layer J2 - for VC-12 layer. This object is applicable only if one of the previous 2 objects is 'enable'.
INT prtSonetVcConnect	1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.6	INTEGER	read-write	Connect VCn (n - 11,12,2,3,4) port (yes/no).
OCT prtSonetVcSignalLabel	1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.7	OCTET STRING	read-write	Signal Label. For VC-3: The SONET standard defines the C2 byte as the path signal label. The purpose of this byte is to communicate the payload type being encapsulated by the SONET Framing OverHead. It allows a single interface to transport multiple payload types simultaneously. For VC-12, VT-1.5: VT path overhead V5 byte allocates bits 5-7 for VT Path Signal Label, to indicate the content of the VT SPE. 000 Unequipped 001 Equipped : non-specific payload 010 Asynchronous mapping 011 Bit synchronous mapping (no longer valid for DS1) 100 Byte synchronous mapping 101 Unassigned 110 Unassigned 111 Unassigned Agents that do not support this feature will send SIZE 0.
prtSonetTuTable	1.3.6.1.4.1.164.3.1.6.2.2.3.2		not-accessible	The write operation into the Table's Objects is valid only for the TmpCnfg entry (Scratch).
prtSonetTuEntry	1.3.6.1.4.1.164.3.1.6.2.2.3.2.1		not-accessible	An entry in table.
I32 prtSonetTuCnfgIdx	1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.1	Integer32	read-only	This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255).
I32 prtSonetTuPrtIdx	1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.2	Integer32	read-only	This object indicates a unique port or interface number. For port numbering, see product's spec. For some products, the numbering can equal ifIndex.
I32 prtSonetTuIdx	1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.3	Integer32	read-only	This object indicates a unique TU (Tributary Unit) within VC-4. The valid TUs are 1..63.
I32 prtSonetTuConPrtIdx	1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.4	Integer32	read-only	This object indicates the connected port, when prtSonetTuType=connect. For port numbering, see product's spec. For some products, the numbering can equal ifIndex. notApplicable - will be indicated as 100.
INT prtSonetTuType	1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.5	INTEGER	read-create	The type of TU (Tributary Unit). connect - connected to one of the E1 ports. bypass - bypassed to the other VC4 port. TUs that are not connected or bypassed, will not exist in this table.
INT prtSonetTuMode	1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.6	INTEGER	read-create	TU Mode of connection. addAndDrop - Add & Drop add - Add (TU receives from the E1 ports).
ROW prtSonetTuRowStatus	1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.7	RowStatus	read-create	Creation/Deletion of rows in the table.
prtVcGroupCnfg	1.3.6.1.4.1.164.3.1.6.2.2.4
vcGroupCnfgTable	1.3.6.1.4.1.164.3.1.6.2.2.4.1		not-accessible	The Virtual Concatenation Group configuration table.
vcGroupCnfgEntry	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1		not-accessible	An entry in the Virtual Concatenation Group configuration table.
I32 vcGroupCnfgIdx	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.1	Integer32	not-accessible	This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255).
I32 vcGroupCnfgNumber	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.2	Integer32	not-accessible	Virtual Concatenation Group Number. For FCD=155 up to eight groups are defined valid values are 1..8
ROW vcGroupCnfgRowStatus	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.3	RowStatus	read-create	Creation/Deletion of rows in the table.
INT vcGroupCnfgVcType	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.4	INTEGER	read-create	User may select type of SDH Virtual Containers (VC) (SONET Virtual Tributaries VT ) to be concatenated in this Virtual Concatenation Group. For SDH, values 2,3,4 are valid. For SONET, values 5 and 6 are valid.
I32 vcGroupCnfgNoOfVCs	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.5	Integer32	read-create	User may select number of Virtual Containers (VC) (SONET Virtual Tributaries VT ) to be concatenated in this Virtual Concatenation Group. Valid range for this number depends on type VC selected by vcGroupCnfgVCType For SDH, up to 63 VC12, or up to 3 VC3, or 1 VC4 are valid For SONET, up to 84 VT1.5 without LCAS, or 64 VT1.5 under LCAS control. or up tp 3 STS-1/SPE, or 1 STS-3
INT vcGroupCnfgLCAS	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.6	INTEGER	read-create	This object controls Link Capacity Adjustment Scheme (LCAS) activation.
INT vcGroupCnfgEncapsulation	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.7	INTEGER	read-create	This object enables user to select encapsulation method.
NUM vcGroupCnfgGroupIfIndex	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.8	InterfaceIndex	read-only	The ifIndex assigend to this group.
INT vcGroupCnfgRip2	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.9	INTEGER	read-create	This object controls RIP 2. User may select to send RIP 2 message over selected group or not
I32 vcGroupCnfgGfpChId	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.10	Integer32	read-create	Generic Framing Procedure (GFP) Channel ID, Valid only when vcGroupCnfgEncapsulation = gfp (4) Valid values are 0x00 - oxFF (hex)
INT vcGroupCnfgK4	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.11	INTEGER	read-create	This object controls whether K4 byte (of Line Overhead) is used as an indication for virtual concatenation (VCAT). This object is applicable, when VCG includes only a single Virtual Container (VC) (or SONET VT)
OCT vcGroupCnfgExSignalLabel	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.12	OCTET STRING	read-create	Extended Signal Label. Relevant only when vcGroupCnfgK4 = yes(3). Agents that do not support this feature will send SIZE 0.
I32 vcGroupCnfgLcasMinNoOfVCs	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.13	Integer32	read-create	Minimum number of VC's to declare alarm, in LCAS mode. Applicable only when LCAS is active (vcGroupCnfgLCAS =lcasActive) 1...63 for SDH, 1...84 for SONET 0= not applicable.
INT vcGroupCnfgLcasStatus	1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.14	INTEGER	read-only	This object summarize LCAS states of all VCs in VCG: belowMinNoOfVCs - Number of VCs in Norm state is less than the minimum number of VCs (indicated by vcGroupCnfgLcasMinNoOfVCs) withinRange - Number of VCs in Norm state is higher than the minimum number of VCs indicated by vcGroupCnfgLcasMinNoOfVCs) but is lower than Number of VCs mapped allNorm - Number of VCs in Norm state equals number of mapped VCs.
vcgGfpMuxCnfgTable	1.3.6.1.4.1.164.3.1.6.2.2.4.2		not-accessible	The Virtual Concatenation Group GFP Mux configuration table.
vcgGfpMuxCnfgEntry	1.3.6.1.4.1.164.3.1.6.2.2.4.2.1		not-accessible	An entry in the Virtual Concatenation Group GFP Mux configuration table.
I32 vcgGfpMuxCnfgIdx	1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.1	Integer32	not-accessible	This object indicates the Index of the configuration being accessed. Index of 255 relates to the Temporary (Scratch) coninguration. For products that support several configurations, Set can be performed only to the Temporary Config (=255).
I32 vcgGfpMuxCnfgMuxNumber	1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.2	Integer32	not-accessible	Virtual Concatenation Group GFP Mux Number. For FCD=155 up to 4 GFP muxes can be created.
ROW vcgGfpMuxCnfgRowStatus	1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.3	RowStatus	read-create	Creation/Deletion of rows in the table.
STR vcgGfpMuxCnfgMuxName	1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.4	SnmpAdminString	read-create	Virtual Concatenation Group, GFP Mux name.
I32 vcgGfpMuxCnfgPrimeGroup	1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.5	Integer32	read-create	Index of Virtual Concatenation Group used as Primary for the GFP mux created for FCD 155 up to 8 Virtual Concatenation Group are defined: 1 -> Virtual Concatenation Group 1 2 -> Virtual Concatenation Group 2 3 -> Virtual Concatenation Group 3 4 -> Virtual Concatenation Group 4 5 -> Virtual Concatenation Group 5 6 -> Virtual Concatenation Group 6 7 -> Virtual Concatenation Group 7 8 -> Virtual Concatenation Group 8
OCT vcgGfpMuxCnfgGrpBwAlloc	1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.6	OCTET STRING	read-create	This object indicates the allocated bandwidth (BW) to each Virtual Concatenation Group (VCG). Each nibble indicates BW percentage, in 12.5% steps, assigned to a group. For FCD-155, there may be 4 or 8 VCGs. When only 4 VCG exists, only two octets are used. In current GFP Mux,one VCG is identified as primary group by vcGfpMuxConfPrimeGroup. Other VCGs may be secondaries. VCG with allocated BW value of zero does not belong to the GFPmux defined by GFP Mux number. ---------------------------------------- \| Octet 0 \| Octet 1 \| \|Nibble 4 \| Nibble 3\| Nibble 2\| Nibble 1\| MSB \| 7 6 5 4 \| 3 2 1 0 \| 7 6 5 4 \| 3 2 1 0 \| +-------------------+-------------------+ VCG1 VCG2 VCG 3 VCG4 ---------------------------------------- \| Octet 3 \| Octet 4 \| \|Nibble 4 \| Nibble 3\| Nibble 2\| Nibble 1\| \| 7 6 5 4 \| 3 2 1 0 \| 7 6 5 4 \| 3 2 1 0 \| LSB +-------------------+-------------------+ VCG5 VCG6 VCG 7 VCG8 Nibble value - BW Percentage (0...7) (0 ...87.5%) 1 0001 12.5 % 2 0010 25% 3 0011 37.5 ..... 7 0111 87.5% at least one nibble must be greater that zero. Sum of alloacted BW must be 100%. Primary VCG BW must be greater than zero.
virtualIfConfiguration	1.3.6.1.4.1.164.3.1.6.2.2.5
virtualIfGenTable	1.3.6.1.4.1.164.3.1.6.2.2.5.1		not-accessible	Sonet/SDH general port configuration table.
virtualIfGenEntry	1.3.6.1.4.1.164.3.1.6.2.2.5.1.1		not-accessible	An entry in the Sonet/SDH general port configuration table.
I32 virtualIfGenCnfgIdx	1.3.6.1.4.1.164.3.1.6.2.2.5.1.1.1	Integer32	read-only	This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255).
I32 virtualIfGenIdx	1.3.6.1.4.1.164.3.1.6.2.2.5.1.1.2	Integer32	read-only	This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex.
INT virtualIfGenFrameFormat	1.3.6.1.4.1.164.3.1.6.2.2.5.1.1.3	INTEGER	read-write	The frame format. fcsEnabe = Frame will be sent with the FCS bits. fcsDisable = Frame will be sent without the FCS bits .
prtSonetXConnect	1.3.6.1.4.1.164.3.1.6.2.3
prtSonetXConnectTable	1.3.6.1.4.1.164.3.1.6.2.3.1		not-accessible	The write operation into the Table's Objects is valid only for the TmpCnfg entry (Scratch).
prtSonetXConnectEntry	1.3.6.1.4.1.164.3.1.6.2.3.1.1		not-accessible	An entry in table.
I32 prtSonetXConnectCnfgIdx	1.3.6.1.4.1.164.3.1.6.2.3.1.1.1	Integer32	read-only	This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255).
I32 prtSonetXConnectPrtIdx	1.3.6.1.4.1.164.3.1.6.2.3.1.1.2	Integer32	read-only	This object indicates a unique port or interface number. For port numbering, see product's spec. For some products, the numbering can equal ifIndex.
I32 prtSonetXConnectConPrtIdx	1.3.6.1.4.1.164.3.1.6.2.3.1.1.3	Integer32	read-only	This object indicates the connected port. For port numbering, see product's spec. For some products, the numbering can equal ifIndex. notApplicable - will be indicated as 255.
I32 prtSonetXConnectAUGIdx	1.3.6.1.4.1.164.3.1.6.2.3.1.1.4	Integer32	read-only	This object indicates an AUG (Administrative Unit Group) within STM-N. The valid AUGs values are: 1 for STM-1 1...4 for STM-4, 1..16 for STM-16 and 1..64 for STM-64 (STM-64) 255 designates NA.
I32 prtSonetXConnectTUG3Idx	1.3.6.1.4.1.164.3.1.6.2.3.1.1.5	Integer32	read-only	This object indicates a TUG-3 (Tributary Unit Group 3) within VC-4. The valid TUG3s are values are 1..3. and 255 which designates NA
I32 prtSonetXConnectTUG2Idx	1.3.6.1.4.1.164.3.1.6.2.3.1.1.6	Integer32	read-only	This object indicates a TUG2 (Tributary Unit Group 2 ) within VC-3. The valid TUG2's values are 1..7 and 255 which designates NA
I32 prtSonetXConnectTUnIdx	1.3.6.1.4.1.164.3.1.6.2.3.1.1.7	Integer32	read-only	This object indicates a TUn within TUG-2 or TUG-3 (Tributary Unit n, where n is 2, 12 or 11 within TUG-2, or 3 within TUG-3) valid values are 1 for TU-2 1 for TU-3 1..4 for TU-11 1..3 for TU-12 255 designates NA
ROW prtSonetXConnectRowStatus	1.3.6.1.4.1.164.3.1.6.2.3.1.1.8	RowStatus	read-create	Creation/Deletion of rows in the table.
INT prtSonetXConnectDirection	1.3.6.1.4.1.164.3.1.6.2.3.1.1.9	INTEGER	read-create	TU direction of connection. rx=Drop tx=Add both = Add & Drop
INT prtSonetXConnectTuNumber	1.3.6.1.4.1.164.3.1.6.2.3.1.1.10	INTEGER	read-create	This object indicates which TU is used in prtSonetXConnectTUnIdx
prtSonetStatus	1.3.6.1.4.1.164.3.1.6.2.4
prtSonetVcStatTable	1.3.6.1.4.1.164.3.1.6.2.4.1		not-accessible	VC Status Table
prtSonetVcStatEntry	1.3.6.1.4.1.164.3.1.6.2.4.1.1		not-accessible	An entry in the VC status Table.
STR prtSonetVcRxJPathTrace	1.3.6.1.4.1.164.3.1.6.2.4.1.1.1	SnmpAdminString	read-only	Jy Path Trace value received from network. y=1, 2: J1 - for VC-4 layer J2 - for VC-12 layer.
OCT prtSonetVcRxSignalLabel	1.3.6.1.4.1.164.3.1.6.2.4.1.1.2	OCTET STRING	read-only	Signal Label received from network. For VC-3: The SONET standard defines the C2 byte as the path signal label. The purpose of this byte is to communicate the payload type being encapsulated by the SONET Framing OverHead. It allows a single interface to transport multiple payload types simultaneously. For VC-12, VT-1.5: VT path overhead V5 byte allocates bits 5-7 for VT Path Signal Label, to indicate the content of the VT SPE. 000 - Unequipped 001 - Equipped - non specific payload 010 - Asynchronous Mapping 011 - Bit Synchronous Mapping (no longer used) 100 - Byte Synchronous Mapping (TU11 or TU12) 101 - Extended Signal Label for Virtual Concatenation Applications (FCD-155 Default) 110 - Test Signal (0.181) (ITU) 111 - VC AIS (ITU)
INT prtSonetVcLcasSourceState	1.3.6.1.4.1.164.3.1.6.2.4.1.1.3	INTEGER	read-only	Fixed - This is an indication that this end uses fixed bandwidth (non-LCAS mode) Add - This member is about to be added to the group Norm - Normal transmission. EOS - End of Sequence indication and Normal transmission. Idle - IDLE This member is not part of the group or about to be removed. Dnu - Do Not use - Do Not Use (the payload) the Sk side reported FAIL status.
INT prtSonetVcLcasSinkState	1.3.6.1.4.1.164.3.1.6.2.4.1.1.4	INTEGER	read-only	Fixed - This is an indication that this end uses fixed bandwidth (non-LCAS mode) Add - This member is about to be added to the group Norm - Normal transmission. EOS - End of Sequence indication and Normal transmission. Idle - IDLE This member is not part of the group or about to be removed. Dnu - Do Not use - Do Not Use (the payload) the Sk side reported FAIL status.

RFC description

Vendor-private MIB for RAD SONET management; monitors SONET transport layer configuration, performance, and alarms for RAD devices.

Start monitoring RAD Data Communications SONET/SDH transport device with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RAD-SONET-MIB