All MIBs › PRESTICOM7-MIB
Category: DSL and Broadband
Description: Manages Presticom DSL modem configuration, line status, ATM PVC parameters, and connection quality reporting.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is PRESTICOM7-MIB?
PRESTICOM7-MIB is a legacy proprietary MIB (enterprise OID 727, built on PAST) reporting system identity, voice-routing/hunt-forwarding, and proxy configuration. Its objects cover a system-description string, a position table, an IP-address table (index, address, type, ifIndex), voice-priority/class settings, hunt-forwarding A/B unit-DLCI-SVC-address triples, backplane RIP version, a trap rack-and-position identifier, and a proxy table (index, community). As a configuration/status MIB it lets an administrator confirm hunt-forwarding routing and proxy community settings on this legacy voice/data access device. It is deployed on legacy voice/data access equipment (enterprise OID 727). Engineers can download the PRESTICOM7-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in PRESTICOM7-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Legacy voice/data access equipment (enterprise OID 727)
Monitoring Examples
An administrator checks sysHuntForwardingAUnit and sysHuntForwardingADLCI to confirm hunt-forwarding routing configuration on this legacy access device.
What Can Be Monitored
- hunt-forwarding routing and proxy community configuration
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| enterprises |
From RFC1213-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| _pysmi_class | 1.3.6.1.4.1.727.7.2.9 | |||
| NTF accountingFileFull | 1.3.6.1.4.1.727.0.631 | Call accounting log file is 90% full. | ||
| NTF accountingFileOverflow | 1.3.6.1.4.1.727.0.669 | Call accounting log file will overflow on next call. | ||
| NTF backupCall | 1.3.6.1.4.1.727.0.612 | A link was activated by the backup mechanism. | ||
| NTF backupHang | 1.3.6.1.4.1.727.0.613 | A link was de-activated by the backup mechanism. | ||
| NTF badChecksum | 1.3.6.1.4.1.727.0.624 | Invalid checksum | ||
| NTF badDestPort | 1.3.6.1.4.1.727.0.610 | This trap indicates a bad destination port. | ||
| NTF badDestPvc | 1.3.6.1.4.1.727.0.611 | This trap indicates a bad destination pvc. | ||
| NTF bondDeTrig | 1.3.6.1.4.1.727.0.617 | Bandwidth On Demand de-trig. | ||
| NTF bondTrig | 1.3.6.1.4.1.727.0.616 | Bandwidth On Demand trig. | ||
| bootp | 1.3.6.1.4.1.727.7.2.33 | |||
| INT bootpEnable | 1.3.6.1.4.1.727.7.2.33.1 | INTEGER | read-write | This variable defines the state of the BOOTP protocol If the BOOTP protocol is enable, the unit will act as a BOOTP/DHCP relay agent by forwarding the BOOTP/DHCP frame. |
| IP bootpIpDestAddr1 | 1.3.6.1.4.1.727.7.2.33.3 | IpAddress | read-write | The Destination IP address 1 - The IP address of the next BOOTP relay agent or server. When a BOOTREQUEST frame is received, this is where the frame is forwarded. Note: When all the Destination IP addresses are 0.0.0.0, BOOTP is in BROADCAST MODE (see documentation). |
| IP bootpIpDestAddr2 | 1.3.6.1.4.1.727.7.2.33.4 | IpAddress | read-write | The Destination IP address 2 - The IP address of the next BOOTP relay agent or server. When a BOOTREQUEST frame is received, this is where the frame is forwarded. Note: When all the Destination IP addresses are 0.0.0.0, BOOTP is in BROADCAST MODE (see documentation). |
| IP bootpIpDestAddr3 | 1.3.6.1.4.1.727.7.2.33.5 | IpAddress | read-write | The Destination IP address 3 - The IP address of the next BOOTP relay agent or server. When a BOOTREQUEST frame is received, this is where the frame is forwarded. Note: When all the Destination IP addresses are 0.0.0.0, BOOTP is in BROADCAST MODE (see documentation). |
| IP bootpIpDestAddr4 | 1.3.6.1.4.1.727.7.2.33.6 | IpAddress | read-write | The Destination IP address 4 - The IP address of the next BOOTP relay agent or server. When a BOOTREQUEST frame is received, this is where the frame is forwarded. Note: When all the Destination IP addresses are 0.0.0.0, BOOTP is in BROADCAST MODE (see documentation). |
| INT bootpMaxHops | 1.3.6.1.4.1.727.7.2.33.2 | INTEGER | read-write | Number maximum of BOOTP relay agent a frame could cross before being discarded |
| NTF bothFansUp | 1.3.6.1.4.1.727.0.629 | Both fans of a rack are running. | ||
| NTF bothPsUp | 1.3.6.1.4.1.727.0.627 | Both PS of a rack are running. | ||
| bridge | 1.3.6.1.4.1.727.7.2.6 | |||
| INT bridgeAgingTime_s | 1.3.6.1.4.1.727.7.2.6.4 | INTEGER | read-write | Aging time, in seconds, for deleting addresses from the routing table. In transparent bridging, the routing table contains a combination of fixed and learned addresses. For the learned addresses, if a station has not been heard from for the AGING TIME period, its entry can be deleted. This process keeps the size of the routing table to a manageable level, and minimizes the amount of memory and processing required to search it. |
| INT bridgeEnable | 1.3.6.1.4.1.727.7.2.6.1 | INTEGER | read-write | This variable defines Bridge enable(yes) or disable(no). If you enable the bridge, the unit transfers information between two LAN segments. |
| INT bridgeForwardDelay_s | 1.3.6.1.4.1.727.7.2.6.7 | INTEGER | read-write | The wait time, in seconds, that the unit spends in the Learning state before moving to the Forwarding state. In the Learning state, the unit is building address tables and participating in the spanning tree algorithm, but is not forwarding frames. In the Forwarding state, the unit forwards frames in addition to its other bridge activities. |
| INT bridgeHelloTime_s | 1.3.6.1.4.1.727.7.2.6.5 | INTEGER | read-write | The interval, in seconds, between HELLO messages that the unit transmits to all LAN segments to which it is connected. HELLO messages carry timestamp information as well as information concerning the current root bridge. From this information the unit is able to determine the current network topology and compute the shortest delay paths to destination devices. Automatic single-route broadcast uses the HELLO message to detect when bridges enter and leave the network. |
| INT bridgeLanType | 1.3.6.1.4.1.727.7.2.6.3 | INTEGER | read-write | The type of LAN data that must be bridged via the unit |
| INT bridgeMaxAge_s | 1.3.6.1.4.1.727.7.2.6.6 | INTEGER | read-write | The maximum time that the bridge can wait for reception of a HELLO frame. If this bridge is the network root bridge, the MAX AGE value will be coded in all HELLO messages that the unit transmits. |
| INT bridgePriority | 1.3.6.1.4.1.727.7.2.6.8 | INTEGER | read-write | Priority assigned to this bridge for the Spanning Tree algorithm. The unit uses this parameter to determine the network topology. |
| INT bridgeStpEnable | 1.3.6.1.4.1.727.7.2.6.2 | INTEGER | read-write | This parameter defines whether the Spanning Tree protocol will be enabled. The unit uses the spanning tree algorithm to decide how to forward frames and how to propagate broadcast packets so that only one copy of a broadcast frame is delivered to each LAN. For transparent bridging, STP ensures that only one active route is used at one time during transparent bridging. For source route bridging, it is used to initialize a single-route broadcast route. |
| INT bridgeTr_MaxHop | 1.3.6.1.4.1.727.7.2.6.11 | INTEGER | read-write | The maximum nember of bridges that a broadcast frame can cross on the way to its destination. The unit discard any frame with a routing information field that exceeds this limits. This parameter is required for source routing of Tocken-Ring data via the unit. You must specify the MAX HOP if the unit acts as an intermediary bridge to reach a remote unit that support a Token-Ring LAN. |
| OCT bridgeTr_Number | 1.3.6.1.4.1.727.7.2.6.9 | OCTET STRING | read-write | The bridge number, required for source routing of Tocken-Ring data via the unit. This number represents the bridge between two links on a Token-Ring network. You must set the bridge number if the unit acts as an intermediary bridge to reach a remote unit that support a Token-Ring LAN. |
| INT bridgeTr_SteSpan | 1.3.6.1.4.1.727.7.2.6.10 | INTEGER | read-write | Span mode for STE (Spanning Tree Explorer) frames, required when Token-Ring data is bridged via the unit. This parameter determines how the port will behave when presented with an STE frame (Single Route Broadcast only). You must set the bridge number if the unit acts as an intermediary bridge to reach a remote unit that support a Token-Ring LAN. |
| NTF cardDown | 1.3.6.1.4.1.727.0.603 | This trap indicates that a card has come down. | ||
| NTF cardup | 1.3.6.1.4.1.727.0.607 | This trap indicates that a card has come up. | ||
| NTF cfgStored | 1.3.6.1.4.1.727.0.619 | A new setup was stored in the unit. | ||
| INT classDefaultClass | 1.3.6.1.4.1.727.7.2.9.2 | INTEGER | read-write | The default class to be used when no class is defined for a port, PU or PVC. |
| classEntry | 1.3.6.1.4.1.727.7.2.9.3.1 | not-accessible | This table contains the principal configurable parameters who are used for a particular class. | |
| INT classIndex | 1.3.6.1.4.1.727.7.2.9.3.1.1 | INTEGER | read-only | A unique value for each class. Its value ranges between 1 and the value of classNumber. |
| INT classNumber | 1.3.6.1.4.1.727.7.2.9.1 | INTEGER | read-only | The number of class present on this system. |
| STR classPrefRoute | 1.3.6.1.4.1.727.7.2.9.3.1.3 | DisplayString | read-write | Identifies the name of the NetPerformer unit to be used as the next hop for sending transparent or PVC multiplex data over multiple direct links (point-to-point or rack backbone connections), where more than one route is available and all available routes are equal in cost. Assigning a different preferred route to different classes ensures static load balancing of transparent traffic over all routes. |
| classTable | 1.3.6.1.4.1.727.7.2.9.3 | not-accessible | A list of class entries. The number of entries is given by the value of classNumber. | |
| INT classWeight | 1.3.6.1.4.1.727.7.2.9.3.1.2 | INTEGER | read-write | The relative bandwidth weight used by this class on the composite link. The higher the weight, the greater the amount of bandwidth allocated to traffic in this class. Thus the class with the highest relative weight will have the highest priority, which can be used to guarantee the response time for mission-critical data. |
| NTF connectionDown | 1.3.6.1.4.1.727.0.600 | This trap indicates that a PU connection has come down. | ||
| NTF connectionUp | 1.3.6.1.4.1.727.0.604 | This trap indicates that a PU connection has come up. | ||
| dP83936 | 1.3.6.1.4.1.727.7.50.4 | |||
| NTF fatalMsg | 1.3.6.1.4.1.727.0.625 | The operating system fail to process a msg. | ||
| NTF fatalTrap | 1.3.6.1.4.1.727.0.621 | The operating system fail to execute a trap. | ||
| filter | 1.3.6.1.4.1.727.7.2.8 | |||
| INT filterActive | 1.3.6.1.4.1.727.7.2.8.2.1.2 | INTEGER | read-write | Sets the activation status of the filter. |
| STR filterDefinition | 1.3.6.1.4.1.727.7.2.8.2.1.3 | DisplayString | read-write | The definition of the filter. Each filter definition contains a set of criteria that prevent extraneous frames from being forwarded, or send specific frames over the high or low-priority bridge channel of the composite link. The latter application allows you to prioritize a particular traffic type over the Bridge 1 channel. |
| filterEntry | 1.3.6.1.4.1.727.7.2.8.2.1 | not-accessible | This table contains the principal configurable parameters who are used for a particular filter. | |
| INT filterIndex | 1.3.6.1.4.1.727.7.2.8.2.1.1 | INTEGER | read-only | A unique value for each filter. Its value ranges between 1 and the value of filterNumber. |
| INT filterNumber | 1.3.6.1.4.1.727.7.2.8.1 | INTEGER | read-only | The number of filter present on this system. |
| filterTable | 1.3.6.1.4.1.727.7.2.8.2 | not-accessible | A list of filter entries. The number of entries is given by the value of filterNumber. | |
| NTF firmwareStored | 1.3.6.1.4.1.727.0.618 | A new firmware was stored in the unit. | ||
| NTF frLinkDown | 1.3.6.1.4.1.727.0.666 | This trap indicates that a frame relay link has come down. | ||
| NTF frLinkUp | 1.3.6.1.4.1.727.0.665 | This trap indicates that a frame relay link has come up. | ||
| iflan | 1.3.6.1.4.1.727.7.2.3 | |||
| INT iflanCost | 1.3.6.1.4.1.727.7.2.3.2.1.6 | INTEGER | read-only | The path cost assigned to the LAN port on the unit for the Spanning Tree algorithm. This indicates to the automatic single-route bridge function the relative length of the path between the local unit port and the attached LAN. The higher the value, the less preferred the route. |
| STR iflanDesc | 1.3.6.1.4.1.727.7.2.3.2.1.2 | DisplayString | read-only | A textual string containing information about a specific interface. |
| iflanEntry | 1.3.6.1.4.1.727.7.2.3.2.1 | not-accessible | This table contains the principal configurable parameters which are used for a particular lan interface. | |
| INT iflanEth_LinkIntegrity | 1.3.6.1.4.1.727.7.2.3.2.1.12 | INTEGER | read-write | Heartbeat feature enabled or disabled, which determines whether the unit supports Link Integrity. When heartbeat is enabled (YES), the unit supports the Link Integrity mode. This is required when the Ethernet 10BASE-T port is connected to a hub. When the HEARTBEAT parameter is set to NO, the unit does not support Link Integrity. Valid only for Ethernet. |
| INT iflanIndex | 1.3.6.1.4.1.727.7.2.3.2.1.1 | INTEGER | read-only | A unique value for each interface. |
| IP iflanIpAddress | 1.3.6.1.4.1.727.7.2.3.2.1.8 | IpAddress | read-write | IP address for the local port. This address is a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte. When set to 000.000.000.000, no IP address is defined on the unit. |
| INT iflanIpRip | 1.3.6.1.4.1.727.7.2.3.2.1.16 | INTEGER | read-write | When this parameter is set to V1, the RIP routing is done according to the RIP V1 standard. With RIP V2, broadcast or multicast can be used. With RIP V2 MULTICAST, only RIP V2 compliant devices will receive RIP frames. |
| INT iflanIpRipAuthType | 1.3.6.1.4.1.727.7.2.3.2.1.31 | INTEGER | read-write | Enable or disable password authentication for the interface. If you select Simple Password, the password will be included in the sent RIP frames. The received frames containing authentication will be accepted only if the password is valid. |
| STR iflanIpRipPassword | 1.3.6.1.4.1.727.7.2.3.2.1.32 | DisplayString | read-write | This configured data allows the authentication procedure to generate and/or verify the authentication field in the RIP header. This value again must be the same for each interface on each side of the link. |
| INT iflanIpRipTxRx | 1.3.6.1.4.1.727.7.2.3.2.1.30 | INTEGER | read-write | This parameter allows RIP frames transmission only, RIP frames reception only or both transmission and reception of RIP frames. |
| INT iflanIpxLanType | 1.3.6.1.4.1.727.7.2.3.2.1.20 | INTEGER | read-write | This parameter define the IPX frame type that the unit will recognize, Other frame type will be discarded |
| OCT iflanIpxNetNum | 1.3.6.1.4.1.727.7.2.3.2.1.19 | OCTET STRING | read-write | This value identify the IPX network number which the lan port of the unit is connected to |
| INT iflanIpxRip | 1.3.6.1.4.1.727.7.2.3.2.1.17 | INTEGER | read-write | if this parameter is enable, the unit will generate IPX RIP frame on that interface every minute, otherwise the unit will discard all IPX RIP frame received and no one will be generated on that port. |
| INT iflanIpxSap | 1.3.6.1.4.1.727.7.2.3.2.1.18 | INTEGER | read-write | if this parameter is enable, the unit will generate IPX SAP frame on that interface every minute, otherwise the unit will discard all IPX SAP frame received and no one will be generated on that port. |
| INT iflanMaxFrame | 1.3.6.1.4.1.727.7.2.3.2.1.10 | INTEGER | read-write | Maximum frame size, in octets. This parameter determines the largest datagram that can be sent or received on the interface in one IP frame. Datagrams larger than the maximum frame size are divided into fragments before transmission, the reassembled at the remote end. |
| INT iflanNumber | 1.3.6.1.4.1.727.7.2.3.1 | INTEGER | read-only | The number of network interfaces present on this system. |
| IP iflanOspfAreaId | 1.3.6.1.4.1.727.7.2.3.2.1.22 | IpAddress | read-write | Identifies the area to which this interface belongs. |
| INT iflanOspfDeadInt | 1.3.6.1.4.1.727.7.2.3.2.1.27 | INTEGER | read-write | After ceasing to hear a router's Hello Packets, the number of seconds before its neighbors declare the router down. This is also advertised in the router's Hello Packets in their RouterDeadInterval field. This value again bust be the same for all routers attached to a common network. |
| INT iflanOspfEnable | 1.3.6.1.4.1.727.7.2.3.2.1.21 | INTEGER | read-write | Indicates whether or not OSPF is enabled on this interface. |
| INT iflanOspfHelloInt | 1.3.6.1.4.1.727.7.2.3.2.1.26 | INTEGER | read-write | The length of time, in seconds, between the Hello Packets that the router sends on the interface. This value is advertised in the router's Hello Packets. It must be the same for all routers attached to a common network. The smaller the HelloInterval, the faster topological changes will be detected, but more OSPF routing protocol traffic will ensue. |
| INT iflanOspfMetricCost | 1.3.6.1.4.1.727.7.2.3.2.1.29 | INTEGER | read-write | The cost of sending a packet on the interface, expressed in the link state metric. This is advertised as the link cost for this interface in the router's router links advertisement. |
| STR iflanOspfPassword | 1.3.6.1.4.1.727.7.2.3.2.1.28 | DisplayString | read-write | This configured data allows the authentication procedure to generate and/or verify the authentication field in the OSPF header. This value again must be the same for all routers attached to a common network. |
| INT iflanOspfPriority | 1.3.6.1.4.1.727.7.2.3.2.1.23 | INTEGER | read-write | When two routers attached to a network both attempt to become Designated Router, the one with the highest Router Priority takes precedence. A router whose Router Priority is set to 0 is ineligible to become Designated Router on the attached network. Router Priority is only configured for interfaces to multi-access networks. |
| INT iflanOspfRetransmitInt | 1.3.6.1.4.1.727.7.2.3.2.1.25 | INTEGER | read-write | The number of seconds between like state advertisement retransmissions for adjacencies belonging to this interface. Also used when retransmitting Database Description and Link State Request Packets. |
| INT iflanOspfTransitDelay | 1.3.6.1.4.1.727.7.2.3.2.1.24 | INTEGER | read-write | The estimated number of seconds it takes to transmit a Link State Update Packet over this interface. |
| OCT iflanPhysAddr | 1.3.6.1.4.1.727.7.2.3.2.1.7 | OCTET STRING | read-write | Network (or MAC) address of the unit. This address can be set to any value using 12 hexadecimal digits (6 bytes). However, the unit automatically sets the first byte to 40 for a Token-Ring LAN, or 02 for an Ethernet LAN, which forces the use of a locally administered address. When this parameter is set to 000000000000, the unit uses its burned-in address. |
| INT iflanPriority | 1.3.6.1.4.1.727.7.2.3.2.1.5 | INTEGER | read-only | Priority assigned to the LAN port on the unit for the Spanning Tree algorithm. |
| INT iflanProtocol | 1.3.6.1.4.1.727.7.2.3.2.1.3 | INTEGER | read-write | Operating protocol for the LAN port. |
| INT iflanSpeed | 1.3.6.1.4.1.727.7.2.3.2.1.4 | INTEGER | read-write | The port speed. |
| IP iflanSubnetMask | 1.3.6.1.4.1.727.7.2.3.2.1.9 | IpAddress | read-write | Subnet mask associated with the port's IP address. It is configured like the IP address: a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte. The subnet mask identifies which bits of the IP address correspond to the physical network, and which bits correspond to host identifiers. |
| iflanTable | 1.3.6.1.4.1.727.7.2.3.2 | not-accessible | A list of interface entries. The number of entries is given by the value of iflanNumber. | |
| INT iflanTr_Etr | 1.3.6.1.4.1.727.7.2.3.2.1.14 | INTEGER | read-write | Early Token Release feature enabled or disabled. When this feature is enabled and the TR port speed is set to 16 Mbps, the unit will send an 'early token' as soon as the transmission of a frame is completed on the ring. When ETR is disabled, the unit waits until the reception of a frame is completed on the ring before sending a token. Valid only for Token-Ring. |
| INT iflanTr_Monitor | 1.3.6.1.4.1.727.7.2.3.2.1.13 | INTEGER | read-write | Contender or non-contender as an active monitor. When this parameter is set to YES, the unit is a contender as the ring monitor. That is, if no ring monitors are active, the unit will automatically negotiate with other devices in the network to select a new monitor, and may become the new ring monitor. When this parameter is set to NO, the unit is a non-contender. That is, it will not negotiate with other devices and cannot become an active monitor. Valid only for Token-Ring. |
| OCT iflanTr_RingNumber | 1.3.6.1.4.1.727.7.2.3.2.1.15 | OCTET STRING | read-write | The local LAN number, used for a source routing bridge. Valid only for Token-Ring. |
| ifvce | 1.3.6.1.4.1.727.7.2.18 | |||
| INT ifvceActivationType | 1.3.6.1.4.1.727.7.2.18.2.1.6 | INTEGER | read-write | For each NetPerformer voice port, voice/fax line activation can be configured according to one of the following activation types. |
| INT ifvceAnalogLinkDwnBusy | 1.3.6.1.4.1.727.7.2.18.2.1.38 | INTEGER | read-write | Used by SDM-9400 VFC03, the SDM-9400 VFC03R cards and by the SDM-9300 voice ports for versions 7.0.3 and lower. See ifvceLinkDwnBusy for version 7.1.0 and higher and for DVC cards. |
| INT ifvceBroadcastDir | 1.3.6.1.4.1.727.7.2.18.2.1.36 | INTEGER | read-write | When line activation is broadcast (Activation Type parameter set to BROADCAST), this parameter is used to specify whether the voice port will transmit(TX) or receive (RX) broadcast messages. |
| INT ifvceBroadcastPvc | 1.3.6.1.4.1.727.7.2.18.2.1.37 | INTEGER | read-write | This parameter specifies which PVC will be used for transmitting (on the root) or receiving (on leaves) the broadcast frames. |
| INT ifvceDelDigits | 1.3.6.1.4.1.727.7.2.18.2.1.24 | INTEGER | read-write | This parameter specifies the number of leading dial digits (if any) that will be deleted from a dial string before it is forwarded to the attached voice equipment. When set to 0, no dial digits are deleted. |
| STR ifvceDesc | 1.3.6.1.4.1.727.7.2.18.2.1.2 | DisplayString | read-only | A textual string containing information about a specific interface. |
| INT ifvceDTalkThreshold | 1.3.6.1.4.1.727.7.2.18.2.1.51 | INTEGER | read-write | This parameter specifies the echo cancellation threshold, measured in 1 db increments. |
| INT ifvceDtmfOnTime | 1.3.6.1.4.1.727.7.2.18.2.1.54 | INTEGER | read-write | This parameter specifies the DTMF ON duration, in milliseconds, for filtering unwanted DTMF tones during call progress. |
| INT ifvceDVCLocalInbound | 1.3.6.1.4.1.727.7.2.18.2.1.34 | INTEGER | read-write | This parameter specifies the local voice level into the port, measured in 1 db increments. ONLY FOR ACT/NETWORKS DVC CARDS |
| INT ifvceDVCLocalOutbound | 1.3.6.1.4.1.727.7.2.18.2.1.35 | INTEGER | read-write | This parameter specifies the local voice level out of the port, measured in 1 db increments. ONLY FOR ACT/NETWORKS DVC CARDS |
| INT ifvceDVCSilenceSuppress | 1.3.6.1.4.1.727.7.2.18.2.1.33 | INTEGER | read-write | This parameter specifies the degree to which periods of silence will be suppressed and reduced during transmission. A higher Silence Suppression level increases the attenuation of the line, lowers background noise and reduces overall bandwidth use. ONLY FOR ACT/NETWORKS DVC CARDS |
| INT ifvceEnableDtmfOnTime | 1.3.6.1.4.1.727.7.2.18.2.1.55 | INTEGER | read-write | This parameter specifies whether the duration of DTMF ON can be used to filter unwanted DTMF tones during call progress. If DTMF ON-TIME configuration is enabled, the next parameter is also listed. |
| ifvceEntry | 1.3.6.1.4.1.727.7.2.18.2.1 | not-accessible | This table contains the principal configurable parameters which are used for a particular voice interface. | |
| INT ifvceExtendedDigitSrc | 1.3.6.1.4.1.727.7.2.18.2.1.53 | INTEGER | read-write | Specifies the origin of the extended digits that will be forwarded to the remote unit. Available on a port configured with Autodial activation type. |
| STR ifvceExtNumber | 1.3.6.1.4.1.727.7.2.18.2.1.25 | DisplayString | read-write | This parameter specifies the extension number for the end device attached to this voice port. |
| INT ifvceFaxModemRelay | 1.3.6.1.4.1.727.7.2.18.2.1.18 | INTEGER | read-write | This parameter enables or disables handling of fax or modem calls on this unit's voice channel. |
| INT ifvceFwdDelay_ms | 1.3.6.1.4.1.727.7.2.18.2.1.23 | INTEGER | read-write | This parameter specifies the length, in milliseconds, of a pause that precedes the forwarded dial digit string. The value entered with a SET is rounded down to the nearest multiple of 250 ms |
| INT ifvceFwdDigits | 1.3.6.1.4.1.727.7.2.18.2.1.21 | INTEGER | read-write | This parameter specifies which dial digits (if any) should be forwarded to the remote unit. When set to 0, no dial digits are forwarded to the destination device when a call is initiated on this channel. When set to a non-zero value, the specified number of dial digits are forwarded. |
| INT ifvceFwdType | 1.3.6.1.4.1.727.7.2.18.2.1.22 | INTEGER | read-write | This parameter specifies how the dial digits are sent to the remote unit for forwarding to the attached device such as a PBX. It can do it using pulse dial or Tone. |
| INT ifvceFxoTimeout_s | 1.3.6.1.4.1.727.7.2.18.2.1.19 | INTEGER | read-write | This parameter determines the maximum amount of time, in seconds, that the local port will wait for a fax transmission to begin. |
| INT ifvceHuntGroup | 1.3.6.1.4.1.727.7.2.18.2.1.8 | INTEGER | read-write | When line activation is defined as switched, this parameter permits hunting more than one port to place an incoming call. |
| INT ifvceIndex | 1.3.6.1.4.1.727.7.2.18.2.1.1 | INTEGER | read-only | A unique value for each voice interface. |
| INT ifvceInterface | 1.3.6.1.4.1.727.7.2.18.2.1.4 | INTEGER | read-write | fxs: Used when connecting to a POTS line or fx0 unit. e-and-m: Used when connecting to the trunk side of a PBX. fx0: Used when connecting to a CO or the station side of a PBX. |
| INT ifvceLinkDwnBusy | 1.3.6.1.4.1.727.7.2.18.2.1.27 | INTEGER | read-write | Used by SDM-9400 VFC03, the SDM-9400 VFC03R cards and by the SDM-9300 voice ports for versions 7.1.0 and higher. Used only for DVC cards for versions 7.0.3 and lower. See also ifvceAnalogLinkDwnBusy for versions 7.0.3 and lower. |
| INT ifvceLocalInbound | 1.3.6.1.4.1.727.7.2.18.2.1.16 | INTEGER | read-write | This parameter specifies the local voice level into the port, measured in 1 db increments. ONLY FOR ACT/NETWORKS CARDS OTHER THAN DVC |
| INT ifvceLocalOutbound | 1.3.6.1.4.1.727.7.2.18.2.1.17 | INTEGER | read-write | This parameter specifies the local voice level out of the port, measured in 1 db increments. ONLY FOR ACT/NETWORKS CARDS OTHER THAN DVC |
| INT ifvceMaxFaxModemRate | 1.3.6.1.4.1.727.7.2.18.2.1.44 | INTEGER | read-write | This parameter enables or disables handling of fax or modem calls on this unit's voice channel. |
| INT ifvceNumber | 1.3.6.1.4.1.727.7.2.18.1 | INTEGER | read-only | The number of voice interfaces present on this system. |
| INT ifvceProtocol | 1.3.6.1.4.1.727.7.2.18.2.1.3 | INTEGER | read-write | Operating protocol for the NetVoice port. Enter ACELP 8 kbs, ACELP 4.8 kbs when you want to use the port for voice/fax transmissions. Select the OFF value when the port is not used. |
| INT ifvcePulseMakeBreak_ms | 1.3.6.1.4.1.727.7.2.18.2.1.10 | INTEGER | read-write | This parameter specifies the duration, in milliseconds, of the contact(or make) for each digit that is dialed using rotary type dialing. |
| INT ifvceR2BusyDigit | 1.3.6.1.4.1.727.7.2.18.2.1.43 | INTEGER | read-write | This parameter defines the digit that is output to indicate that the destination is busy. |
| INT ifvceR2CompleteDigit | 1.3.6.1.4.1.727.7.2.18.2.1.42 | INTEGER | read-write | This parameter defines the digit that is output when dialing is complete. |
| INT ifvceR2ExtendedDigitSrc | 1.3.6.1.4.1.727.7.2.18.2.1.40 | INTEGER | read-write | No longer supported by the NP Agent 7.1.0 and higher |
| INT ifvceR2Group2Digit | 1.3.6.1.4.1.727.7.2.18.2.1.41 | INTEGER | read-write | This parameter defines a Group 2 Digit that is output when dialing out. |
| INT ifvceRate4k8x1 | 1.3.6.1.4.1.727.7.2.18.2.1.49 | INTEGER | read-write | This parameter enables fallback to 4.8 Kbps with single buffering. |
| INT ifvceRate4k8x2 | 1.3.6.1.4.1.727.7.2.18.2.1.50 | INTEGER | read-write | This parameter enables fallback to 4.8 Kbps with double buffering. |
| INT ifvceRate5k8x1 | 1.3.6.1.4.1.727.7.2.18.2.1.31 | INTEGER | read-write | This parameter enables fallback to 5.8 Kbps with single buffering. |
| INT ifvceRate5k8x2 | 1.3.6.1.4.1.727.7.2.18.2.1.32 | INTEGER | read-write | This parameter enables fallback to 5.8 Kbps with double buffering. |
| INT ifvceRate6kx1 | 1.3.6.1.4.1.727.7.2.18.2.1.46 | INTEGER | read-write | This parameter enables fallback to 6 Kbps with single buffering. |
| INT ifvceRate6kx2 | 1.3.6.1.4.1.727.7.2.18.2.1.47 | INTEGER | read-write | This parameter enables fallback to 6 Kbps with double buffering. |
| INT ifvceRate6kx3 | 1.3.6.1.4.1.727.7.2.18.2.1.48 | INTEGER | read-write | This parameter enables fallback to 6 Kbps with triple buffering. |
| INT ifvceRate8kx1 | 1.3.6.1.4.1.727.7.2.18.2.1.29 | INTEGER | read-write | This parameter enables fallback to 8 Kbps with single buffering. |
| INT ifvceRate8kx2 | 1.3.6.1.4.1.727.7.2.18.2.1.30 | INTEGER | read-write | This parameter enables fallback to 8 Kbps with double buffering. |
| INT ifvceRate8kx3 | 1.3.6.1.4.1.727.7.2.18.2.1.45 | INTEGER | read-write | This parameter enables fallback to 8 Kbps with triple buffering. |
| INT ifvceRemotePort | 1.3.6.1.4.1.727.7.2.18.2.1.5 | INTEGER | read-write | Specifies the port number on the remote unit for setting up predefined line activation. Select the number of the port connected to the device you want to reach. |
| STR ifvceRemoteUnit | 1.3.6.1.4.1.727.7.2.18.2.1.7 | DisplayString | read-write | Specifies the unit name of the NetVoice card at the remote site, for setting up predefined line activation. |
| INT ifvceSignaling | 1.3.6.1.4.1.727.7.2.18.2.1.14 | INTEGER | read-write | The signaling protocol of this port. |
| INT ifvceSilenceSuppress | 1.3.6.1.4.1.727.7.2.18.2.1.13 | INTEGER | read-write | This parameter specifies the degree to which periods of silence will be suppressed and reduced during transmission. A higher Silence Suppression level increases the attenuation of the line, lowers background noise and reduces overall bandwidth use. ONLY FOR ACT/NETWORKS CARDS OTHER THAN DVC |
| STR ifvceSpeedDialNum | 1.3.6.1.4.1.727.7.2.18.2.1.39 | DisplayString | read-write | Specifies the Speed Dial Number to be dialed when a off-hook occurs on a port configured with Autodial activation type. |
| ifvceTable | 1.3.6.1.4.1.727.7.2.18.2 | not-accessible | A list of interface entries. The number of entries is given by the value of ifvceNumber. | |
| INT ifvceTeTimer_s | 1.3.6.1.4.1.727.7.2.18.2.1.20 | INTEGER | read-write | This parameter determines the delay, in seconds, between M-lead and E-lead activation when the starting method is timed e-and-m. |
| INT ifvceToneDetectRegen_s | 1.3.6.1.4.1.727.7.2.18.2.1.9 | INTEGER | read-write | This parameter specifies the number of seconds during which Tone tones will be detected and regenerated. |
| INT ifvceToneEnergyDetec | 1.3.6.1.4.1.727.7.2.18.2.1.52 | INTEGER | read-write | This parameter controls whether DTMF detection will include the detection of energy as well as tones. In some cases, DTMF detection will work only if the energy is not detected. |
| INT ifvceToneOff_ms | 1.3.6.1.4.1.727.7.2.18.2.1.12 | INTEGER | read-write | This parameter specifies the duration, in milliseconds, of the silence between Tone tones in a dial digit string. |
| INT ifvceToneOn_ms | 1.3.6.1.4.1.727.7.2.18.2.1.11 | INTEGER | read-write | This parameter specifies the duration, in milliseconds, of the tone used to produce a single Tone digit. |
| INT ifvceToneType | 1.3.6.1.4.1.727.7.2.18.2.1.28 | INTEGER | read-write | This parameter specifies the kind of multi-frequency tone that will be detected on this port. |
| ifwan | 1.3.6.1.4.1.727.7.2.2 | |||
| INT ifwanBackupCall_s | 1.3.6.1.4.1.727.7.2.2.2.1.25 | INTEGER | read-write | Delay, in seconds, before activating the backup link when a line failure has occurred on a dedicated link. |
| INT ifwanBackupHang_s | 1.3.6.1.4.1.727.7.2.2.2.1.26 | INTEGER | read-write | Delay, in seconds, before deactivating the backup WAN link after the dedicated link has been restored. |
| INT ifwanBChannels | 1.3.6.1.4.1.727.7.2.2.2.1.62 | INTEGER | read-write | This parameter permits to enable two independent 64 kbits/s channel for use as B-channels. |
| INT ifwanBodCall_s | 1.3.6.1.4.1.727.7.2.2.2.1.22 | INTEGER | read-write | The call trigger period, in seconds, for the Bandwidth ON Demand function. This defines the period of time during which the combined WAN link usage must be a the BOD level (define with the BOD LEVEL parameter) or higher before another WAN link will be activated. It is, in effect, a means of validating the requirement for a new link |
| INT ifwanBodHang_s | 1.3.6.1.4.1.727.7.2.2.2.1.23 | INTEGER | read-write | The hold time, in seconds, for minimum link activation under the Bandwidth On Demand function. This defines the minimum period of time during which a newly added WAN link will remain activated, even if the usage level drops rapidly. This parameter can prevent unnecessary link activation/deactivation procedures when the traffic flow fluctuates widely. |
| INT ifwanBodLevel | 1.3.6.1.4.1.727.7.2.2.2.1.24 | INTEGER | read-write | The call trigger level for the Bandwidth On Demand function. It represents the combined WAN link usage level, given as a percentage of the total bandwidth, at which another link should be activated. This defines a threshold at which another wan link will be added to ease the traffic flow. |
| INT ifwanCellPacketization | 1.3.6.1.4.1.727.7.2.2.2.1.93 | INTEGER | read-write | Indicates whether or not cell packetization is enabled on this interface. |
| INT ifwanChannelCompressed | 1.3.6.1.4.1.727.7.2.2.2.1.141 | INTEGER | read-write | Channel compressed. |
| STR ifwanChExp | 1.3.6.1.4.1.727.7.2.2.2.1.86 | DisplayString | read-write | A 32 byte string describing the cross connection of every DS0 of this interface: - DS0 timeslot 1 is represent by the left most character. - every byte of the field correspond to a DS0 channel assign to a specific DVC slot number, i.e. DS0 number 8 is represented by the second byte of the string and represent timeslot 2 crossconnect to a DVC in slot 8, and so on up to DS0 number 32. - a digit k ( k in the range '1' to '8') placed at the nth position in the string means that the nth DS0 is crossconnected to the expansion slot number k for example: R8--------------R-------------76 Timeslot 1 and 17 are always reserved when using an E1 span. When using a T1 span all DS0 timeslots are available. This would mean that the DS0 nr 2 is crossconnected to slot 8, DS0 nr 31 is crossconnected to a DVC in slot 7, DS0 nr 32 is crossconnected to a DVC in slot 6. The - or I characters means that there is no cross connection. |
| STR ifwanChUse | 1.3.6.1.4.1.727.7.2.2.2.1.72 | DisplayString | read-write | A 32 byte string describing the use of each DS0 of the span: - '-' or 'i' means off - 'P' means used in passthru mode - 'V' means used as a voice channel - 'R' means reserved ( cannot be set, valid only on EICs) for example: RV--------------R--------------P DS0 timeslot 1 is represent by the left most character. Timeslot 1 and 17 are always reserved when using an E1 span. When using a T1 span all DS0 timeslots are available. This would mean that the DS0 timeslot 1 is used as a reserved channel, the DS0 timeslot 2 is used as a voice channel and the DS0 timeslot 17 is used as a reserved channel and DS0 timeslot 32 is used as a passthru channel |
| INT ifwanClassNumber | 1.3.6.1.4.1.727.7.2.2.2.1.30 | INTEGER | read-write | The priority class for data from this port. Classes are defined according to bandwidth weight. |
| INT ifwanCllm | 1.3.6.1.4.1.727.7.2.2.2.1.47 | INTEGER | read-write | Frame Relay CLLM control. The value of this parameter determines the behavior of the unit regarding the Consolidated Link Management Option. When set to OFF, CLLM messages received are discarded and none are generated. When set to ON, CLLM messages are generated on the FR-NET when PVC becomes congested or blocked and frames received are analyzed. |
| INT ifwanClocking | 1.3.6.1.4.1.727.7.2.2.2.1.7 | INTEGER | read-write | Clock source for the port. For ports on the processor/LAN interface board (ports 1 and 2) the clock source is automatically controlled by the unit, and cannot be changed. For all protocols. |
| INT ifwanCoding | 1.3.6.1.4.1.727.7.2.2.2.1.8 | INTEGER | read-write | For SDLC and HDLC protocols only. Bit coding for CRC purposes. For NORMAL and NRZI coding the computed CRC is preset at 1. For normal coding with CRC0 (CRC0-NML) and NRZI coding with CRC0 (CRC0-NZI) the computed CRC is preset at 0. The values NRZ-CRC0 and NRZI-CRC0 are available for the HDLC protocol only. |
| INT ifwanCompression | 1.3.6.1.4.1.727.7.2.2.2.1.36 | INTEGER | read-write | Use compression on the WAN link connection to the remote unit. With compression, the available bandwidth is used more efficiently. When compression is not used, higher speeds can be obtained on the link. |
| INT ifwanCondLMIPort | 1.3.6.1.4.1.727.7.2.2.2.1.95 | INTEGER | read-write | Indicates which FR-USER port will be used as a reference port to respond to LMI request. If 'none' is specified, the FR-NET port will always answer to LMI request. If a port is specified, the FR-NET port will answer to LMI request only if the indicated port receives answers to its LMI request. |
| INT ifwanConnTimeout_s | 1.3.6.1.4.1.727.7.2.2.2.1.98 | INTEGER | read-write | This parameter determines the maximum amount of time, in seconds, that the voice port who initiates the call will wait for a call connect confirmed |
| INT ifwanCrc4 | 1.3.6.1.4.1.727.7.2.2.2.1.60 | INTEGER | read-write | CRC-4 procedure enable or disable. |
| STR ifwanDesc | 1.3.6.1.4.1.727.7.2.2.2.1.2 | DisplayString | read-only | A textual string containing information about a specific interface. |
| STR ifwanDestExtNumber | 1.3.6.1.4.1.727.7.2.2.2.1.97 | DisplayString | read-write | Destination extension number |
| INT ifwanDialer | 1.3.6.1.4.1.727.7.2.2.2.1.28 | INTEGER | read-write | Backup link dialer mode |
| INT ifwanDialTimeout_s | 1.3.6.1.4.1.727.7.2.2.2.1.92 | INTEGER | read-write | Delay, in seconds, allowed to establish a dial-up backup link. |
| INT ifwanDigitNumber | 1.3.6.1.4.1.727.7.2.2.2.1.110 | INTEGER | read-write | Object specific to the ISDN BRI Voice card. It contains the number of digits to wait for before the setup request is forwarded on the port. This object is usefull only when the ifwanTerminating is set to NT. |
| OCT ifwanDropSyncCharacter | 1.3.6.1.4.1.727.7.2.2.2.1.20 | OCTET STRING | read-write | For COP protocol only. The hexadecimal value of the desynchronization character. This parameter defines the value of the desynchronization character in hexadecimal. |
| INT ifwanDropSyncCounter | 1.3.6.1.4.1.727.7.2.2.2.1.19 | INTEGER | read-write | For COP protocol only. Drop synchronization counter. This parameter defines the number of contiguous desynchronization characters that must be received before the unit drops synchronization and closes the frame. |
| INT ifwanDsOSpeed_bps | 1.3.6.1.4.1.727.7.2.2.2.1.55 | INTEGER | read-write | Speed of a DS0 channel: 64000 bps or 56000 bps. |
| INT ifwanDuplex | 1.3.6.1.4.1.727.7.2.2.2.1.12 | INTEGER | read-write | Port duplex mode. When set to FULL (DUPLEX), the SDLC driver can transmit INFO frames to a secondary port while polling another secondary port. |
| INT ifwanEncodingLaw | 1.3.6.1.4.1.727.7.2.2.2.1.88 | INTEGER | read-write | The PCM coding law in effect on this interface. Configuration CFG-WPORT-ENCODING-LAW |
| INT ifwanEnquiryTimer_s | 1.3.6.1.4.1.727.7.2.2.2.1.44 | INTEGER | read-write | Frame Relay Enquiry Timer. The unit polls the network with STATUS ENQUIRY frames when this timer expires. |
| ifwanEntry | 1.3.6.1.4.1.727.7.2.2.2.1 | not-accessible | This table contains the principal configurable parameters which are used for a particular wan interface. | |
| STR ifwanExtNumber | 1.3.6.1.4.1.727.7.2.2.2.1.96 | DisplayString | read-write | Port extension number |
| INT ifwanFallBackSpeed_bps | 1.3.6.1.4.1.727.7.2.2.2.1.5 | INTEGER | read-write | Fallback speed for the transmitter. Fallback is available only if the unit is set for DCE internal clocking. If in DTE, the fallback rate is ignored. Set this parameter to 0 to disable fallback. For all user protocols except ASYNC and PASSTHRU. Applicable to SDM-8200, SDM-8300 and SDM-9530 only. The maximum for DDCMP, BSC and COP is 64000. |
| INT ifwanFallBackSpeedEnable | 1.3.6.1.4.1.727.7.2.2.2.1.91 | INTEGER | read-write | Enable the Fallback speed mechanism for the transmitter. Fallback is available only if the unit is set for DCE internal clocking. If in DTE, the fallback rate is ignored. Set this parameter to no to disable the fallback. The actual fallback speed is automatically computed and set by the unit. For all user protocols except ASYNC and PASSTHRU. Applicable to SDM-9300 and SDM-9400 only |
| INT ifwanFlowControl | 1.3.6.1.4.1.727.7.2.2.2.1.42 | INTEGER | read-write | Congestion flow control notification. If the FLOW CTRL parameter is ON, the unit will set the Forward and Backward Congestion Bits in the header of the active PVC frame when congestion occurs on the unit port. Forward data congestion affects data transmitted from Frame Relay equipment to the unit port. Backward data congestion affects data transmitted from the unit to the Frame Relay equipment. If the FLOW CTRL parameter is OFF, the unit does not set the congestion bits. In this cas, they are reset to zero |
| INT ifwanFormat | 1.3.6.1.4.1.727.7.2.2.2.1.17 | INTEGER | read-write | For ASYNC and COP protocols only. Character format. The parameter values are different for the ASYNC and COP protocols. ASYNC Protocols: The parameter defines the number of data bits per character, the parity bit usage, number of stop bits and idle characters. When not specified in the parameter value, the number of stop bits is 1. 8N-2STOP configures the port for 8 bits, no parity and 2 stop bits. Values: 8-NONE, 8-ODD, 8-EVEN, 7-NONE, 7-ODD, 7-EVEN, 7 SPACE, 7-MARK, 7-IGNORE, 8N-2STOP COP Protocol: The parameter defines the number of bits per character only. Values: 8 bits, 6 bits |
| INT ifwanFrameDelay | 1.3.6.1.4.1.727.7.2.2.2.1.16 | INTEGER | read-write | For HDLC protocol only. Delay, in milliseconds, added between each frame transmitted on the unit port. This delay is required by some DTE equipment operating at speeds higher than 56 Kbps. |
| INT ifwanFraming | 1.3.6.1.4.1.727.7.2.2.2.1.58 | INTEGER | read-write | Framing format (ESF or D4). ***** NOTE: This parameter applies only to TIC, not to EIC. |
| INT ifwanGainLimit | 1.3.6.1.4.1.727.7.2.2.2.1.77 | INTEGER | read-write | this object specifies the gain to be applied on received DS1 signal. ***** NOTE: This parameter applies only to TIC, not to EIC. |
| OCT ifwanGroupAddress | 1.3.6.1.4.1.727.7.2.2.2.1.14 | OCTET STRING | read-write | For P-SDLC and S-SDLC protocols only. Group address. This parameter is used when the group poll feature is enabled (see ifwanGroupPoll parameter, above). |
| INT ifwanGroupPoll | 1.3.6.1.4.1.727.7.2.2.2.1.13 | INTEGER | read-write | For P-SDLC and S-SDLC protocols only. Group poll enabled or disabled. When this parameter is set to YES, the group poll feature is enabled, using the address set with the group address parameter, described below. When this parameter is set to NO, the group poll feature is disabled. |
| INT ifwanHighPriorityTransparentClass | 1.3.6.1.4.1.727.7.2.2.2.1.139 | INTEGER | read-write | High priority transparent class. |
| INT ifwanIdle | 1.3.6.1.4.1.727.7.2.2.2.1.11 | INTEGER | read-write | For HDLC, SDLC and COP protocols only. Transmitter idle state, which determines the characters to be sent when no data frame is transmitted. When configured as FLAG, the transmitter continuously sends 7E (flags). When configured as MARK, it continuously sends 1. When configured as MARKD, the MARK IDLE state is postponed 20 msec after the end of a frame. When configured as SPACE, it continuously sends 0. |
| OCT ifwanIdleCode | 1.3.6.1.4.1.727.7.2.2.2.1.79 | OCTET STRING | read-write | this object specifies the byte to be transmitted when no real data to transmit |
| INT ifwanIndex | 1.3.6.1.4.1.727.7.2.2.2.1.1 | INTEGER | read-only | A unique value for each interface. |
| INT ifwanInterface | 1.3.6.1.4.1.727.7.2.2.2.1.6 | INTEGER | read-write | Interface selection. |
| IP ifwanIpAddress | 1.3.6.1.4.1.727.7.2.2.2.1.32 | IpAddress | read-write | IP address for the local port. This address is a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte. When set to 000.000.000.000, no IP address is defined for this port. In this case the unit will use the default IP address defined with the global DEFAULT IP ADDR parameter. |
| INT ifwanIpRip | 1.3.6.1.4.1.727.7.2.2.2.1.46 | INTEGER | read-write | When this parameter is set to V1, the RIP routing is done according to the RIP V1 standard. With RIP V2, broadcast or multicast can be used. With RIP V2 MULTICAST, only RIP V2 compliant devices will receive RIP frames. |
| INT ifwanIpRipAuthType | 1.3.6.1.4.1.727.7.2.2.2.1.119 | INTEGER | read-write | Enable or disable password authentication for the interface. If you select Simple Password, the password will be included in the sent RIP frames. The received frames containing authentication will be accepted only if the password is valid. |
| STR ifwanIpRipPassword | 1.3.6.1.4.1.727.7.2.2.2.1.120 | DisplayString | read-write | This configured data allows the authentication procedure to generate and/or verify the authentication field in the RIP header. This value again must be the same for each interface on each side of the link. |
| INT ifwanIpRipTxRx | 1.3.6.1.4.1.727.7.2.2.2.1.118 | INTEGER | read-write | This parameter allows RIP frames transmission only, RIP frames reception only or both transmission and reception of RIP frames. |
| OCT ifwanIpxNetNum | 1.3.6.1.4.1.727.7.2.2.2.1.50 | OCTET STRING | read-write | This value identify the IPX network number which the unit is connected to |
| INT ifwanIpxRip | 1.3.6.1.4.1.727.7.2.2.2.1.48 | INTEGER | read-write | if this parameter is enable, the unit will generate IPX RIP frame on that interface every minute, otherwise the unit will discard all IPX RIP frame received and no one will be generated on that port. |
| INT ifwanIpxSap | 1.3.6.1.4.1.727.7.2.2.2.1.49 | INTEGER | read-write | if this parameter is enable, the unit will generate IPX SAP frame on that interface every minute, otherwise the unit will discard all IPX SAP frame received and no one will be generated on that port. |
| INT ifwanLineBuild | 1.3.6.1.4.1.727.7.2.2.2.1.80 | INTEGER | read-write | this object specifies the build out to be applied on transmitted DS1 signal. ***** NOTE: This parameter applies only to TIC, not to EIC. |
| INT ifwanLineCoding | 1.3.6.1.4.1.727.7.2.2.2.1.61 | INTEGER | read-write | 1's density control or zero suppression over the line. |
| INT ifwanMaxChannels | 1.3.6.1.4.1.727.7.2.2.2.1.94 | INTEGER | read-write | Indicates the maximum number of voice channels permitted on this port. |
| INT ifwanMaxFrame | 1.3.6.1.4.1.727.7.2.2.2.1.34 | INTEGER | read-write | Maximum frame size, in octets. This parameter determines the largest datagram that can be sent or received on the interface in one IP frame. Datagrams larger than the maximum frame size are divided into fragments before transmission, the reassembled at the remote end. |
| INT ifwanMgmtInterface | 1.3.6.1.4.1.727.7.2.2.2.1.43 | INTEGER | read-write | Frame Relay Management Protocol. The LMI (Local Management Interface) uses the reserved DLCI address 1023. The ANNEX-D and the Q-933 protocols uses the reserved DLCI address 0. Set this parameter according to the Management Interface Protocol used on the network connected to the unit port. |
| INT ifwanMode | 1.3.6.1.4.1.727.7.2.2.2.1.21 | INTEGER | read-write | For PVCR protocol only. Operating mode of the WAN link. This parameter defines the WAN link as a dedicated link, a backup link or a Bandwidth On Demand link. The ANSWER mode is used for the link that responds to calls. When you install a backup or Bandwidth On Demand (BOD) link between two units, one unit must be configured in call mode (CALL-BACKUP or CALL-BOD) and the other as ANSWER. The INACTIVE mode is used to turn off the link. |
| INT ifwanModem | 1.3.6.1.4.1.727.7.2.2.2.1.9 | INTEGER | read-write | Modem control signal operating mode. If the port is DCE this parameter controls the operating mode of the DCD control signal. In STATIC mode the DCD signal is active at all times. In DYNAMIC mode it is active only when a frame is transmitted. If the port is DTE this parameter controls the operating mode of the RTS control signal. In STATIC mode the RTS signal is active at all times. In DYNAMIC mode it is active only when a frame is transmitted. |
| STR ifwanMsn1 | 1.3.6.1.4.1.727.7.2.2.2.1.111 | DisplayString | read-write | Object specific to the ISDN BRI Voice card. Contains the First ISDN number on which the port will accept an incoming connection request. This object is usefull only when ifwanTerminating is set to TE. |
| STR ifwanMsn2 | 1.3.6.1.4.1.727.7.2.2.2.1.112 | DisplayString | read-write | Object specific to the ISDN BRI Voice card. Second ISDN number on which the port will accept an incoming connection request. This object is usefull only when ifwanTerminating is set to TE while ifwanTeiMode is set to Dynamic. |
| STR ifwanMsn3 | 1.3.6.1.4.1.727.7.2.2.2.1.113 | DisplayString | read-write | Object specific to the ISDN BRI Voice card. Third ISDN number on which the port will accept an incoming connection request. This object is usefull only when ifwanTerminating is set to TE while ifwanTeiMode is set to Dynamic. |
| INT ifwanMultiframing | 1.3.6.1.4.1.727.7.2.2.2.1.63 | INTEGER | read-write | The Multiframing provides a layer1 signalling capability between the TE and the NT. |
| INT ifwanNumber | 1.3.6.1.4.1.727.7.2.2.1 | INTEGER | read-only | The number of wan interfaces present on this system. |
| IP ifwanOspfAreaId | 1.3.6.1.4.1.727.7.2.2.2.1.65 | IpAddress | read-write | Identifies the area to which this interface belongs. |
| INT ifwanOspfDeadInt | 1.3.6.1.4.1.727.7.2.2.2.1.69 | INTEGER | read-write | After ceasing to hear a router's Hello Packets, the number of seconds before its neighbors declare the router down. This is also advertised in the router's Hello Packets in their RouterDeadInterval field. This value again bust be the same for all routers attached to a common network. |
| INT ifwanOspfEnable | 1.3.6.1.4.1.727.7.2.2.2.1.64 | INTEGER | read-write | Indicates whether or not OSPF is enabled on this interface. |
| INT ifwanOspfHelloInt | 1.3.6.1.4.1.727.7.2.2.2.1.68 | INTEGER | read-write | The length of time, in seconds, between the Hello Packets that the router sends on the interface. This value is advertised in the router's Hello Packets. It must be the same for all routers attached to a common network. The smaller the HelloInterval, the faster topological changes will be detected, but more OSPF routing protocol traffic will ensue. |
| INT ifwanOspfMetricCost | 1.3.6.1.4.1.727.7.2.2.2.1.71 | INTEGER | read-write | The cost of sending a packet on the interface, expressed in the link state metric. This is advertised as the link cost for this interface in the router's router links advertisement. |
| STR ifwanOspfPassword | 1.3.6.1.4.1.727.7.2.2.2.1.70 | DisplayString | read-write | This configured data allows the authentication procedure to generate and/or verify the authentication field in the OSPF header. This value again must be the same for all routers attached to a common network. |
| INT ifwanOspfRetransmitInt | 1.3.6.1.4.1.727.7.2.2.2.1.67 | INTEGER | read-write | The number of seconds between like state advertisement retransmissions for adjacencies belonging to this interface. Also used when retransmitting Database Description and Link State Request Packets. |
| INT ifwanOspfTransitDelay | 1.3.6.1.4.1.727.7.2.2.2.1.66 | INTEGER | read-write | The estimated number of seconds it takes to transmit a Link State Update Packet over this interface. |
| INT ifwanPollDelay_ms | 1.3.6.1.4.1.727.7.2.2.2.1.15 | INTEGER | read-write | The wait time, in milliseconds, before transmitting a poll. |
| INT ifwanPortToBack | 1.3.6.1.4.1.727.7.2.2.2.1.27 | INTEGER | read-write | The WAN link that this port backs up. Backup links can be configured to monitor and backup a specific link (1..8) any link that fails (ANY) or all other unit links (ALL). NOTE: The number of available links varies with each product. |
| OCT ifwanPppAcceptableAccmChar | 1.3.6.1.4.1.727.7.2.2.2.1.131 | OCTET STRING | read-write | This parameter determines the exact characters of the Asynchronous Control Character Map that will be sent to the remote peer. The Async-Control-Character-Map field is 4 bytes, encoded such that each numbered bit corresponds to the ASCII control character of the same value. If a bit is cleared to zero, then the corresponding ASCII control character must remain mapped. For example, if bit 19 is set to zero, then ASCII control character 19 (CTRL-S) may be sent without change. |
| INT ifwanPppAcceptAccmPeer | 1.3.6.1.4.1.727.7.2.2.2.1.130 | INTEGER | read-write | This parameter determines whether the port will accept a request from the remote peer to enter into Asynchronous Control Character Map (ACCM) negotiation. Set this parameter to YES to accept the peer's request. Set it to NO (the default value) to reject the request for ACCM negotiation. If you set this parameter to YES, you must also configure the Acceptable ACCM Characters parameter. |
| INT ifwanPppAcceptIpAddress | 1.3.6.1.4.1.727.7.2.2.2.1.136 | INTEGER | read-write | This parameter determines whether the port will accept a request from the remote peer to send an IP Address. Set this parameter to YES ( the default value) to accept the peer's request for the local IP Address. Set it to NO to reject the request. |
| INT ifwanPppAcceptMagicNum | 1.3.6.1.4.1.727.7.2.2.2.1.133 | INTEGER | read-write | This parameter determines whether the port will accept a request from the remote peer to send the local Magic Number. Set this parameter to YES (the default value) to accept the peer's Magic Number request. Set it to NO to reject the request. |
| INT ifwanPppAcceptOldIpAddNeg | 1.3.6.1.4.1.727.7.2.2.2.1.134 | INTEGER | read-write | This parameter determines whether the port will accept a request from the remote peer to negotiate old IP-Addresses. Set this parameter to YES to accept the peer's IP-Addresses Negotiation request. The port will enter into an obsolete IP address negotiation with the peer. Set it to NO (the default value) to reject this configuration option. |
| INT ifwanPppConfigRestartTimer | 1.3.6.1.4.1.727.7.2.2.2.1.122 | INTEGER | read-write | This parameter defines the duration, in seconds, of the Restart timer, which is started when a Configure-Request or Terminate-Request packet is transmitted. If the timer expires a timeout occurs, followed by retransmission of the packet. Configure the Configuration Restart Timer parameter based on the speed of the link. The default value, 3 seconds, is designed for low-speed lines (from 2400 to 9600 bps) and links having a high switching latency, such as telephone lines. For higher speed links or links with low switching latency the retransmission time is reduced, so the Retry Period should be reduced also. For example, round trip transmission times for modems at 14,400 bps are in the range of 160 to 600 milliseconds. A value of 1 second for the Configuration Restart Timer would be appropriate. |
| INT ifwanPppConfigRetries | 1.3.6.1.4.1.727.7.2.2.2.1.123 | INTEGER | read-write | This parameter is a restart counter for Configure-Requests. It defines the maximum number of successive retry periods that can elapse when the port attempts to send a Configure-Request packet to the remote peer. The port counts the number of retry periods that elapse before receiving a Configure-Ack, Configure-Nak or Configure-Reject from the peer, until it assumes that the peer is unable to respond. The values 0 to 254 set a finite number of retry periods. Use the value 255 to allow the port to send a Configure-Request packet an unlimited number of times. |
| INT ifwanPppLocalMru | 1.3.6.1.4.1.727.7.2.2.2.1.125 | INTEGER | read-write | This parameter determines the size of the MRU that the local port offers (if greater than the default value) or requests (if less than the default value) for use by the peer. The MRU specifies the maximum number of bytes allowed in the Information and Padding fields of the PPP encapsulation frame. |
| INT ifwanPppNegociateAccm | 1.3.6.1.4.1.727.7.2.2.2.1.128 | INTEGER | read-write | This parameter determines whether the port will inform the remote peer that it can enter into Asynchronous Control Character Map (ACCM) negotiation. This option provides a way to negotiate the use of control character mapping on asynchronous links. By default, PPP maps all control characters into an appropriate two-character sequence. This is usually not necessary. The NetPerformer uses the ACCM negotiation option to inform the remote end which control characters must remain mapped, and which ones do not need to remain mapped when the remote end sends them. Set this parameter to YES to permit ACCM negotiation. Set it to NO (the default value) to disallow this negotiation process. If you set this parameter to YES, you must also configure the Requested ACCM Characters parameter. |
| INT ifwanPppNegociateIpAddress | 1.3.6.1.4.1.727.7.2.2.2.1.135 | INTEGER | read-write | This parameter enables the negotiation of an IP Address with the remote peer. Set this parameter to YES (the default value) to allow the port to request and accept an IP Address. Set it to NO to disallow IP address negotiation. |
| INT ifwanPppNegociateLocalMru | 1.3.6.1.4.1.727.7.2.2.2.1.124 | INTEGER | read-write | This parameter enables the negotiation of another MRU than the default MRU value (1500 bytes). The MRU is used when sending parameter values between peers to negotiate the connection. In particular, it specifies the maximum number of bytes in the Information and Padding fields of the PPP encapsulation frame. If you set this parameter to YES, you must also configure the Negotiated Local MRU parameter. |
| INT ifwanPppNegociatePeerMru | 1.3.6.1.4.1.727.7.2.2.2.1.126 | INTEGER | read-write | This parameter determines whether the port will consider either an offer for a larger MRU value or a request for a smaller one. Set this parameter to YES to allow the port to consider an MRU offer or request from the peer. Set it to NO (the default value) to reject it. If you set this parameter to YES, you must also configure the Peer's MRU parameter. |
| INT ifwanPppPeerMruUpTo | 1.3.6.1.4.1.727.7.2.2.2.1.127 | INTEGER | read-write | This parameter determines up to what limit above the default MRU value the local port will set its MRU in response to an offer or request from the peer. |
| IP ifwanPppRemoteIpAddress | 1.3.6.1.4.1.727.7.2.2.2.1.137 | IpAddress | read-write | This parameter defines the IP-Address to be sent to the remote peer during negotiation of the connection. The IP-Address is specific to a particular PPP session. It is a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte, for example 128.128.128.122. When this parameter is set to 000.000.000.000, no IP-Address is defined. |
| IP ifwanPppRemoteSubnetMask | 1.3.6.1.4.1.727.7.2.2.2.1.138 | IpAddress | read-write | Subnet mask associated with the Remote IP address. It is configured like the IP address: a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte. The subnet mask identifies which bits of the IP address correspond to the physical network, and which bits correspond to host identifiers. |
| OCT ifwanPppRequestedAccmChar | 1.3.6.1.4.1.727.7.2.2.2.1.129 | OCTET STRING | read-write | This parameter determines the exact characters of the Asynchronous Control Character Map that are requested from the remote peer. The Async-Control-Character-Map field is 4 bytes long. It encoded such that each numbered bit corresponds to the ASCII control character of the same value. If a bit is cleared to zero, then the corresponding ASCII control character must remain mapped. For example, if bit 19 is set to zero, then ASCII control character 19 (CTRL-S) will not be changed during transmission. |
| INT ifwanPppRequestMagicNum | 1.3.6.1.4.1.727.7.2.2.2.1.132 | INTEGER | read-write | This parameter determines whether the port will request the Magic Number from the remote peer. The Magic Number is a 4-byte field that aids in the detection of link loopback conditions and other data link layer anomalies. Set this parameter to YES (the default value) to request the peer's Magic Number. Set it to NO to disallow a Magic Number request. |
| INT ifwanPppSilent | 1.3.6.1.4.1.727.7.2.2.2.1.121 | INTEGER | read-write | This parameter defines how this port participates in the configuration negotiation process. When a PPP port is Silent, it waits for a Configure-Request packet from the remote peer. Use WAIT FOR REQUEST to configure the port in this way. The port must receive a request before it can negotiate a connection. When a port is not Silent, it is actively trying to initialize the connection with the remote peer. Use the SEND REQUEST setting. The port will send Configure-Request packets in a timeout/retry sequence until the remote peer replies, at which point the two peers can negotiate the connection. |
| INT ifwanPriority | 1.3.6.1.4.1.727.7.2.2.2.1.37 | INTEGER | read-only | Priority assigned to the WAN port for the Spanning Tree algorithm. |
| INT ifwanProtocol | 1.3.6.1.4.1.727.7.2.2.2.1.3 | INTEGER | read-write | Operating protocol for the WAN/user port. |
| INT ifwanPvcNumber | 1.3.6.1.4.1.727.7.2.2.2.1.115 | INTEGER | read-write | PVC this port will use to carry X25 traffic over frame relay. |
| INT ifwanQsigPbxAb | 1.3.6.1.4.1.727.7.2.2.2.1.116 | INTEGER | read-write | Object specific to the E1 card, when QSIG signaling is used. Specifies the DTE/DCE operation mode of the QSIG port. |
| INT ifwanQsigPbxXy | 1.3.6.1.4.1.727.7.2.2.2.1.117 | INTEGER | read-write | Object specific to the E1 card, when QSIG signaling is used. Object used as an arbitrator in case of collisions between the E1 card and the connected device (i.e. the local PBX). One side of the connection has to be set to X while the other side of the connection has to be set to Y. |
| INT ifwanRemotePort | 1.3.6.1.4.1.727.7.2.2.2.1.41 | INTEGER | read-write | For all user protocols except SDLC and PVCR. The remote port to which data from the local port is sent. Specify the port number on the remote unit. |
| STR ifwanRemoteUnit | 1.3.6.1.4.1.727.7.2.2.2.1.29 | DisplayString | read-write | Remote unit to which data from this port should be directed |
| INT ifwanReportCycle | 1.3.6.1.4.1.727.7.2.2.2.1.45 | INTEGER | read-write | Full Status Enquiry Cycle. The value of this parameter determines the number of STATUS ENQUIRY frames that the unit will send before sending a full status enquiry to the network. In response to a full status enquiry the network will send a full status report. This report indicates the currently active PVC on the network. The unit uses this information to determine if a particular PVC is ready to receive data. It is also used in determining the number of restart errors for PVCs in PVCR mode. |
| INT ifwanRetry | 1.3.6.1.4.1.727.7.2.2.2.1.40 | INTEGER | read-write | Maximum number of successive retries before the WAN link is declared down. |
| OCT ifwanRingNumber | 1.3.6.1.4.1.727.7.2.2.2.1.31 | OCTET STRING | read-write | The ring number of the remote Token-ring LAN, required for source routing of Token-Ring data via the unit. |
| INT ifwanRxFlow | 1.3.6.1.4.1.727.7.2.2.2.1.52 | INTEGER | read-write | For R-ASYNC protocol only. Flow control on the receiver. This parameter describes the method used by the unit to control the flow of data received from the attached equipment. Flow control is applied when the number of characters on input exceeds a predefined threshold. |
| INT ifwanSfCarrierId | 1.3.6.1.4.1.727.7.2.2.2.1.144 | INTEGER | read-write | Identifier of a physical port in a Skyframe system. |
| INT ifwanSfMode | 1.3.6.1.4.1.727.7.2.2.2.1.143 | INTEGER | read-write | Enable/disable the data transmission/reception on the port. |
| INT ifwanSfType | 1.3.6.1.4.1.727.7.2.2.2.1.142 | INTEGER | read-write | Specify the type of Skyframe port configured. It can be a Modulator, Demodulator, Expansion or Aggregate. |
| INT ifwanSignaling | 1.3.6.1.4.1.727.7.2.2.2.1.78 | INTEGER | read-write | Specifies what type of signalling is in effect on this port. NOTE: 1) none and t1-rob-bit are valid only for a TIC card. 2) e1-cas, trsp-orig, trsp-answ and qsig are valid only for a EIC card. 3) e1-ccs is no longer used. |
| INT ifwanSpeed_bps | 1.3.6.1.4.1.727.7.2.2.2.1.4 | INTEGER | read-write | Port speed or PVC CIR and BIR. 1200 to 64000 for DDCMP, BSC and COP. 110 to 115200 for TASYNC and RASYNC. 1200 to 128000 for PASSTRHU. 1200 to 2000000 for PVCs, PSDLC, SSDLC, HDLC, X25, FR-USER, FR-NET, PVCR. |
| IP ifwanSubnetMask | 1.3.6.1.4.1.727.7.2.2.2.1.33 | IpAddress | read-write | Subnet mask associated with the port IP address. It is configured like the IP address: a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte. The subnet mask identifies which bits of the IP address correspond to the physical network, and which bits correspond to host identifiers. |
| INT ifwanSvcAddressType | 1.3.6.1.4.1.727.7.2.2.2.1.99 | INTEGER | read-write | This parameter determines the SVC address type supported by this frame relay port (NONE, E.164 or X.121) |
| INT ifwanSvcCallProceedingTimeoutT310 | 1.3.6.1.4.1.727.7.2.2.2.1.107 | INTEGER | read-write | Response time-out for Q933 call proceeding message (T310). |
| INT ifwanSvcDisconnectTimeoutT305 | 1.3.6.1.4.1.727.7.2.2.2.1.105 | INTEGER | read-write | Response time-out for Q933 disconnect message (T305). |
| INT ifwanSvcIframeRetransmissionsN200 | 1.3.6.1.4.1.727.7.2.2.2.1.103 | INTEGER | read-write | Maximum number of I frame retransmission's (N200). |
| INT ifwanSvcInactiveTimeoutT203 | 1.3.6.1.4.1.727.7.2.2.2.1.102 | INTEGER | read-write | Maximum number of seconds without activity (T203). |
| INT ifwanSvcMaxTxTimeoutT200 | 1.3.6.1.4.1.727.7.2.2.2.1.101 | INTEGER | read-write | Maximum Tx Acknowledge timeout (T200). |
| STR ifwanSvcNetworkAddress | 1.3.6.1.4.1.727.7.2.2.2.1.100 | DisplayString | read-write | Local SVC Network address. |
| INT ifwanSvcReleaseTimeoutT308 | 1.3.6.1.4.1.727.7.2.2.2.1.106 | INTEGER | read-write | Response time-out for Q933 release message (T308). |
| INT ifwanSvcSetupTimeoutT303 | 1.3.6.1.4.1.727.7.2.2.2.1.104 | INTEGER | read-write | Response time-out for Q933 setup message (T303). |
| INT ifwanSvcStatusTimeoutT322 | 1.3.6.1.4.1.727.7.2.2.2.1.108 | INTEGER | read-write | Response time-out for Q933 status enquiry message (T322). |
| OCT ifwanSync | 1.3.6.1.4.1.727.7.2.2.2.1.18 | OCTET STRING | read-write | For COP protocol only. The hexadecimal value of the synchronization character. |
| INT ifwanT1E1InterBit | 1.3.6.1.4.1.727.7.2.2.2.1.87 | INTEGER | read-write | Use this parameter to enable or disable setting of the International Bit (I-bit). |
| INT ifwanT1E1LoopBack | 1.3.6.1.4.1.727.7.2.2.2.1.85 | INTEGER | read-write | This object is used to enable/disable loopback on T1/E1 interfaces. The types of loopback depend on the type of T1/E1 interface used. |
| INT ifwanT1E1Status | 1.3.6.1.4.1.727.7.2.2.2.1.84 | INTEGER | read-write | This parameter sets the activation status of the T1 port, that is, the preferred T1 port state (enabled or disabled). |
| ifwanTable | 1.3.6.1.4.1.727.7.2.2.2 | not-accessible | A list of interface entries. The number of entries is given by the value of ifwanNumber. | |
| INT ifwanTeiMode | 1.3.6.1.4.1.727.7.2.2.2.1.109 | INTEGER | read-write | Object specific to the ISDN BRI Voice card. Indicates the TEI mode used for the interface. When Dynamic is selected, the TEI is negotiated between the NT and the TE devices. Whenever Fixed is selected, the TEI value 0 is used to establish the session. |
| INT ifwanTerminating | 1.3.6.1.4.1.727.7.2.2.2.1.59 | INTEGER | read-write | Terminating (NT indicate Network terminating and TE indicate terminal terminating). |
| INT ifwanTimeout | 1.3.6.1.4.1.727.7.2.2.2.1.39 | INTEGER | read-write | The wait for ACK timeout before retransmitting a frame on the WAN link. |
| INT ifwanTransparentClassNumber | 1.3.6.1.4.1.727.7.2.2.2.1.140 | INTEGER | read-write | The transparent priority class for voice. Classes are defined according to bandwidth weight. |
| INT ifwanTxFlow | 1.3.6.1.4.1.727.7.2.2.2.1.53 | INTEGER | read-write | For R-ASYNC protocol only. Flow control on the transmitter. This parameter describes the method used by the attached equipment to control the flow of data transmitted by the unit. |
| INT ifwanTxHold_s | 1.3.6.1.4.1.727.7.2.2.2.1.54 | INTEGER | read-write | For R-ASYNC protocol only. Transmitter hold time. This parameter defines the maximum hold time that the transmitter can be blocked due to flow control. There is no hold time limit if TX HOLD is configured as 0 seconds. |
| INT ifwanTxStart | 1.3.6.1.4.1.727.7.2.2.2.1.10 | INTEGER | read-write | For all user protocols except ASYNC, PASSTH and COP. Transmit start level. This is the number of characters that are accumulated before the transmitter is enabled when a frame is incomplete. When set to MAX, the transmitter is enabled only when a complete frame has been accumulated by the unit. This value prevents underruns but can introduce unnecessary delays. When the transmit start level is set to a numeric value, the transmitter is enabled at that level even if a frame coming from the remote unit has not been completely received. If the port is in DCE-INTRN mode and fallback is enabled, the transmitter falls back when the number of characters of an incomplete frame in the output queue goes below the transmit start level. Otherwise, no fallback occurs. |
| INT ifwanTxStartCop | 1.3.6.1.4.1.727.7.2.2.2.1.89 | INTEGER | read-write | For COP protocol only. Transmit start level. This is the number of characters that are accumulated before the transmitter is enabled when a frame is incomplete. When set to MAX, the transmitter is enabled only when a complete frame has been accumulated by the unit. This value prevents underruns but can introduce unnecessary delays. When the transmit start level is set to a numeric value, the transmitter is enabled at that level even if a frame coming from the remote unit has not been completely received. If the port is in DCE-INTRN mode and fallback is enabled, the transmitter falls back when the number of characters of an incomplete frame in the output queue goes below the transmit start level. Otherwise, no fallback occurs. |
| INT ifwanTxStartPass | 1.3.6.1.4.1.727.7.2.2.2.1.90 | INTEGER | read-write | For PASSTRHU protocol only. Transmit start level. This is the number of transparent blocks that are accumulated before the transmitter is enabled when a frame is incomplete. |
| INT ifwanX25Encapsulation | 1.3.6.1.4.1.727.7.2.2.2.1.114 | INTEGER | read-write | Defines the encapsulation method used to transport X25 over frame relay. |
| info | 1.3.6.1.4.1.727.7.50 | |||
| intf | 1.3.6.1.4.1.727.7.2.30 | |||
| STR intfDesc | 1.3.6.1.4.1.727.7.2.30.2.1.2 | DisplayString | read-only | A textual string containing information about a specific interface. |
| intfEntry | 1.3.6.1.4.1.727.7.2.30.2.1 | not-accessible | This table presents the characteristics that uniquely identifies one interface. | |
| INT intfIndex | 1.3.6.1.4.1.727.7.2.30.2.1.1 | INTEGER | read-only | A unique value for each interface. Matches exaclty the ifIndex of the ifEntry in RFC-1213 |
| INT intfModuleType | 1.3.6.1.4.1.727.7.2.30.2.1.8 | INTEGER | read-only | A unique value for each interface. |
| INT intfNumber | 1.3.6.1.4.1.727.7.2.30.1 | INTEGER | read-only | The number of overall interfaces present on this system. |
| INT intfNumInSlot | 1.3.6.1.4.1.727.7.2.30.2.1.7 | INTEGER | read-only | The logical number of this interface within its slot. |
| INT intfNumInType | 1.3.6.1.4.1.727.7.2.30.2.1.4 | INTEGER | read-only | The logical number of this interface amongst those having the same type. |
| INT intfSlot | 1.3.6.1.4.1.727.7.2.30.2.1.5 | INTEGER | read-only | The localization of this interface, whether on baseCard or in slot, and on what slot |
| INT intfSlotNumber | 1.3.6.1.4.1.727.7.2.31.1 | INTEGER | read-only | The number of overall slots actually presents on this system. |
| INT intfSlotType | 1.3.6.1.4.1.727.7.2.30.2.1.6 | INTEGER | read-only | A unique value for each interface. |
| intfTable | 1.3.6.1.4.1.727.7.2.30.2 | not-accessible | A list of interface entries. The number of entries is given by the value of ifNumber. | |
| INT intfType | 1.3.6.1.4.1.727.7.2.30.2.1.3 | INTEGER | read-only | A unique type value for each interface. |
| ip | 1.3.6.1.4.1.727.7.2.14 | |||
| ipaddr | 1.3.6.1.4.1.727.7.2.32 | |||
| IP ipaddrAddr | 1.3.6.1.4.1.727.7.2.32.2.1.2 | IpAddress | read-write | |
| ipaddrEntry | 1.3.6.1.4.1.727.7.2.32.2.1 | not-accessible | This table is an index list of all ip addresses of this unit. | |
| INT ipaddrIfIndex | 1.3.6.1.4.1.727.7.2.32.2.1.4 | INTEGER | read-only | |
| INT ipaddrIndex | 1.3.6.1.4.1.727.7.2.32.2.1.1 | INTEGER | read-only | |
| INT ipaddrNr | 1.3.6.1.4.1.727.7.2.32.1 | INTEGER | read-only | The number ip addresses identifying this unit |
| ipaddrTable | 1.3.6.1.4.1.727.7.2.32.2 | not-accessible | A list of ip addresses entries. The number of entries is given by the value of ipaddrNr. | |
| INT ipaddrType | 1.3.6.1.4.1.727.7.2.32.2.1.3 | INTEGER | read-only | |
| INT ipRouterEnable | 1.3.6.1.4.1.727.7.2.14.1 | INTEGER | read-write | This variable defines the state of IP Router (enable or disable) . If IP Router parameter is enable, the unit will Route IP frames between different IP networks which unit is connected to, otherwise, all IP frames will be bridged (if BRIDGE is enable) or discarded (if not). |
| ipstatic | 1.3.6.1.4.1.727.7.2.13 | |||
| ipstaticEntry | 1.3.6.1.4.1.727.7.2.13.2.1 | not-accessible | This table contains the principal configurable parameters who are used for a particular IP static entry. | |
| INT ipstaticIndex | 1.3.6.1.4.1.727.7.2.13.2.1.1 | INTEGER | read-only | A unique value for each entry. Its value ranges between 1 and the value of ipstaticNumber. |
| IP ipstaticIpDest | 1.3.6.1.4.1.727.7.2.13.2.1.3 | IpAddress | read-write | The destination IP address which we want include in the address table (e.g. RIP table) |
| IP ipstaticMask | 1.3.6.1.4.1.727.7.2.13.2.1.4 | IpAddress | read-write | The destination IP address mask. |
| IP ipstaticNextHop | 1.3.6.1.4.1.727.7.2.13.2.1.5 | IpAddress | read-write | The IP address of the next hop to reach the destination IP address specified. |
| INT ipstaticNumber | 1.3.6.1.4.1.727.7.2.13.1 | INTEGER | read-only | The number of IP static entries present on this system. |
| ipstaticTable | 1.3.6.1.4.1.727.7.2.13.2 | not-accessible | A list of IP static entries. The number of entries is given by the value of ipstaticNumber. | |
| INT ipstaticValid | 1.3.6.1.4.1.727.7.2.13.2.1.2 | INTEGER | read-write | Sets the activation status of the entry. |
| ipx | 1.3.6.1.4.1.727.7.2.11 | |||
| ipxfilter | 1.3.6.1.4.1.727.7.2.16 | |||
| INT ipxfilterEnable | 1.3.6.1.4.1.727.7.2.16.2.1.2 | INTEGER | read-write | This variable defines the state of IPX filter (enable or disable). If IPX filter parameter is enable, the unit will filter IPX SAP entries for the SAP given. |
| ipxfilterEntry | 1.3.6.1.4.1.727.7.2.16.2.1 | not-accessible | This table contains the principal configurable parameters which are used for a particular IP filter entry. | |
| INT ipxfilterIndex | 1.3.6.1.4.1.727.7.2.16.2.1.1 | INTEGER | read-only | A unique value for each entry. Its value ranges between 1 and the value of ipxfilterNumber. |
| INT ipxfilterNumber | 1.3.6.1.4.1.727.7.2.16.1 | INTEGER | read-only | The number of IPX filter entries present on this system. |
| OCT ipxfilterSap | 1.3.6.1.4.1.727.7.2.16.2.1.3 | OCTET STRING | read-write | This variable defines the SAP value to be filtered. |
| ipxfilterTable | 1.3.6.1.4.1.727.7.2.16.2 | not-accessible | A list of IPX filter entries. The number of entries is given by the value of ipxfilterNumber. | |
| INT ipxfilterType | 1.3.6.1.4.1.727.7.2.16.2.1.4 | INTEGER | read-write | This variable defines how apply the filter. If type is standard, the SAP configured is filtered. If type is reverse, all SAPs except the one configured is filtered. |
| OCT ipxInternalNetNum | 1.3.6.1.4.1.727.7.2.11.2 | OCTET STRING | read-write | This value identify the IPX internal network number. This value is used on unnumbered links. |
| INT ipxRouterEnable | 1.3.6.1.4.1.727.7.2.11.1 | INTEGER | read-write | This variable defines the state of IPX Router (enable or disable) . If IPX Router parameter is enable, the unit will Route all IPX frames between different IPX networks which unit is connected to, otherwise, all IPX frames will be bridged (if BRIDGE is enable) or discarded (if not). |
| NTF linkDown | 1.3.6.1.4.1.727.0.601 | This trap indicates that a link has come down. | ||
| NTF linkUp | 1.3.6.1.4.1.727.0.605 | This trap indicates that a link has come up. | ||
| NTF manualCall | 1.3.6.1.4.1.727.0.614 | A link was manually activated. | ||
| NTF manualHang | 1.3.6.1.4.1.727.0.615 | A link was manually de-activated. | ||
| mC68EN360 | 1.3.6.1.4.1.727.7.50.2 | |||
| mgmt | 1.3.6.1.4.1.727.7.2 | |||
| mibEvolution | 1.3.6.1.4.1.727.7.50.10.7.0.4.1 | |||
| mibSpecialVersion | 1.3.6.1.4.1.727.7.50.10.7.0.4 | |||
| mibSubVersion | 1.3.6.1.4.1.727.7.50.10.7.0 | |||
| mibVersion | 1.3.6.1.4.1.727.7.50.10.7 | |||
| mibVersionInfo | 1.3.6.1.4.1.727.7.50.10 | |||
| netperformer7 | 1.3.6.1.4.1.727.7 | |||
| noDevice | 1.3.6.1.4.1.727.7.1.1 | |||
| NTF noMsg | 1.3.6.1.4.1.727.0.626 | The operating system fail to allocate a msg. | ||
| NTF notMemory | 1.3.6.1.4.1.727.0.622 | The unit has not enough memory. | ||
| NTF noTrap | 1.3.6.1.4.1.727.0.620 | The operating system fail to schedule a trap. | ||
| NTF oneOrMoreFanDown | 1.3.6.1.4.1.727.0.630 | One fan or more on the rack are not running. | ||
| NTF onePsDown | 1.3.6.1.4.1.727.0.628 | One PS of the rack is not running. | ||
| ospf | 1.3.6.1.4.1.727.7.2.15 | |||
| ospfArea | 1.3.6.1.4.1.727.7.2.15.2 | |||
| IP ospfAreaAreaId | 1.3.6.1.4.1.727.7.2.15.2.2.1.2 | IpAddress | read-write | This is a 32-bit number that identifies the area. The Area ID of 0.0.0.0 is reserved for the backbone. |
| INT ospfAreaAuthType | 1.3.6.1.4.1.727.7.2.15.2.2.1.4 | INTEGER | read-write | Enables or disables password authentication for the area. If you select Simple Password, only those routers sharing the correct password will be able to communicate with each other. |
| INT ospfAreaEnable | 1.3.6.1.4.1.727.7.2.15.2.2.1.3 | INTEGER | read-write | Allows you to enable and disable this area. |
| ospfAreaEntry | 1.3.6.1.4.1.727.7.2.15.2.2.1 | not-accessible | This table contains the principal configurable parameters who are used for a particular area. | |
| INT ospfAreaImportASExt | 1.3.6.1.4.1.727.7.2.15.2.2.1.5 | INTEGER | read-write | Indicates whether or not this area imports AS external link state advertisements. If AS external advertisements are excluded from the area, the area is called a stub. The backbone cannot be configured as a stub area. Also, virtual links cannot be configured through stub areas. |
| INT ospfAreaIndex | 1.3.6.1.4.1.727.7.2.15.2.2.1.1 | INTEGER | read-only | A unique value for each entry. Its value ranges between 1 and the value of ospfAreaNumber. |
| INT ospfAreaNumber | 1.3.6.1.4.1.727.7.2.15.2.1 | INTEGER | read-only | The number of areas present on this system. |
| INT ospfAreaStubMetric | 1.3.6.1.4.1.727.7.2.15.2.2.1.6 | INTEGER | read-write | If the area has been configured as a stub area, and the router itself is an area border router, then the StubMetric indicates the cost of the default summary link that the router should advertise into the area. |
| ospfAreaTable | 1.3.6.1.4.1.727.7.2.15.2.2 | not-accessible | A list of areas. The number of areas is given by the value of ospfAreaNumber. | |
| ospfGlobal | 1.3.6.1.4.1.727.7.2.15.1 | |||
| INT ospfGlobalAutoVLink | 1.3.6.1.4.1.727.7.2.15.1.2 | INTEGER | read-write | Indicates if virtual links can be configured automatically or not. |
| IP ospfGlobalGlobalAreaId | 1.3.6.1.4.1.727.7.2.15.1.4 | IpAddress | read-write | This parameter identifies the area to which the NetPerformer's global Default IP Address belongs. |
| IP ospfGlobalRackAreaId | 1.3.6.1.4.1.727.7.2.15.1.3 | IpAddress | read-write | Identifies the area to which the backplane belongs. Valid only on rack products. |
| IP ospfGlobalRouterId | 1.3.6.1.4.1.727.7.2.15.1.1 | IpAddress | read-write | This is a 32-bit number that uniquely identifies the router in the Autonomous System. |
| ospfRange | 1.3.6.1.4.1.727.7.2.15.3 | |||
| IP ospfRangeAddToArea | 1.3.6.1.4.1.727.7.2.15.3.2.1.6 | IpAddress | read-write | The area ID that identifies the area to which this range belongs. |
| INT ospfRangeEnable | 1.3.6.1.4.1.727.7.2.15.3.2.1.4 | INTEGER | read-write | Enables or disables this range for the specified area. |
| ospfRangeEntry | 1.3.6.1.4.1.727.7.2.15.3.2.1 | not-accessible | This table contains the principal configurable parameters who are used for a particular range. | |
| INT ospfRangeIndex | 1.3.6.1.4.1.727.7.2.15.3.2.1.1 | INTEGER | read-only | A unique value for each entry. Its value ranges between 1 and the value of ospfRangeNumber. |
| IP ospfRangeMask | 1.3.6.1.4.1.727.7.2.15.3.2.1.3 | IpAddress | read-write | This parameter, together with Range Net, indicates all of the networks that belong to this range. |
| IP ospfRangeNet | 1.3.6.1.4.1.727.7.2.15.3.2.1.2 | IpAddress | read-write | Describes the collection of Ip addresses contained in the address range. This network address, together with the range mask parameter, specifies the subnets to be grouped in this area range. Just one link summary advertisement will be generated for all subnets in this range. |
| INT ospfRangeNumber | 1.3.6.1.4.1.727.7.2.15.3.1 | INTEGER | read-only | The number of ranges present on this system. |
| INT ospfRangeStatus | 1.3.6.1.4.1.727.7.2.15.3.2.1.5 | INTEGER | read-write | Set to either Advertise or DoNotAdvertise. Unadvertised ranges allow the existence of certain networks to be intentionally hidden from other areas. Status is set to Advertise by default. |
| ospfRangeTable | 1.3.6.1.4.1.727.7.2.15.3.2 | not-accessible | A list of ranges. The number of ranges is given by the value of ospfRangeNumber. | |
| ospfVLink | 1.3.6.1.4.1.727.7.2.15.4 | |||
| INT ospfVLinkDeadInt | 1.3.6.1.4.1.727.7.2.15.4.2.1.8 | INTEGER | read-write | After ceasing to hear a router's Hello Packets, the number of seconds before its neighbors declare the router down. This is also advertised in the router's Hello Packets in their RouterDeadInterval field. This value again bust be the same for all routers attached to a common network. |
| INT ospfVLinkEnable | 1.3.6.1.4.1.727.7.2.15.4.2.1.4 | INTEGER | read-write | Enables or disables this virtual link. |
| ospfVLinkEntry | 1.3.6.1.4.1.727.7.2.15.4.2.1 | not-accessible | This table contains the principal configurable parameters who are used for a particular vlink. | |
| INT ospfVLinkHelloInt | 1.3.6.1.4.1.727.7.2.15.4.2.1.7 | INTEGER | read-write | The length of time, in seconds, between the Hello Packets that the router sends on the interface. This value is advertised in the router's Hello Packets. It must be the same for all routers attached to a common network. The smaller the HelloInterval, the faster topological changes will be detected, but more OSPF routing protocol traffic will ensue. |
| INT ospfVLinkIndex | 1.3.6.1.4.1.727.7.2.15.4.2.1.1 | INTEGER | read-only | A unique value for each entry. Its value ranges between 1 and the value of ospfVLinkNumber. |
| IP ospfVLinkNeighborRtrId | 1.3.6.1.4.1.727.7.2.15.4.2.1.3 | IpAddress | read-write | Indicates the neighbor router ID at the other end of this virtual link. |
| INT ospfVLinkNumber | 1.3.6.1.4.1.727.7.2.15.4.1 | INTEGER | read-only | The number of virtual links present on this system. |
| STR ospfVLinkPassword | 1.3.6.1.4.1.727.7.2.15.4.2.1.9 | DisplayString | read-write | This configured data allows the authentication procedure to generate and/or verify the authentication field in the OSPF header. This value again must be the same for all routers attached to a common network. |
| INT ospfVLinkRetransmitInt | 1.3.6.1.4.1.727.7.2.15.4.2.1.6 | INTEGER | read-write | The number of seconds between like state advertisement retransmissions for adjacencies belonging to this interface. Also used when retransmitting Database Description and Link State Request Packets. |
| ospfVLinkTable | 1.3.6.1.4.1.727.7.2.15.4.2 | not-accessible | A list of virtual links. The number of virtual links is given by the value of ospfVLinkNumber. | |
| IP ospfVLinkTransitAreaId | 1.3.6.1.4.1.727.7.2.15.4.2.1.2 | IpAddress | read-write | Identifies the transit area ID through which the virtual link is configured. |
| INT ospfVLinkTransitDelay | 1.3.6.1.4.1.727.7.2.15.4.2.1.5 | INTEGER | read-write | The estimated number of seconds it takes to transmit a Link State Update Packet over this interface. |
| NTF periodEnded | 1.3.6.1.4.1.727.0.609 | This trap indicates that a period is ended. | ||
| NTF periodStarted | 1.3.6.1.4.1.727.0.608 | This trap indicates that a period is started. | ||
| phone | 1.3.6.1.4.1.727.7.2.7 | |||
| INT phoneCost | 1.3.6.1.4.1.727.7.2.7.2.1.5 | INTEGER | read-write | Normal cost to reach the remote unit. |
| phoneEntry | 1.3.6.1.4.1.727.7.2.7.2.1 | not-accessible | This table contains the principal configurable parameters who are used for a particular phone. | |
| INT phoneIndex | 1.3.6.1.4.1.727.7.2.7.2.1.1 | INTEGER | read-only | A unique value for each phone. Its value ranges between 1 and the value of phoneNumber. |
| STR phoneNextHop | 1.3.6.1.4.1.727.7.2.7.2.1.4 | DisplayString | read-write | Name of the Next hop by which the Remote unit should normally be seen. |
| INT phoneNumber | 1.3.6.1.4.1.727.7.2.7.1 | INTEGER | read-only | The number of phone present on this system. |
| STR phonePhoneNumber | 1.3.6.1.4.1.727.7.2.7.2.1.3 | DisplayString | read-write | Phone number to dial to backup the Remote unit. |
| STR phoneRemoteUnit | 1.3.6.1.4.1.727.7.2.7.2.1.2 | DisplayString | read-write | Name of the unit that has to be backup. |
| phoneTable | 1.3.6.1.4.1.727.7.2.7.2 | not-accessible | A list of phone entries. The number of entries is given by the value of phoneNumber. | |
| presticom | 1.3.6.1.4.1.727 | |||
| product | 1.3.6.1.4.1.727.7.1 | |||
| proxy | 1.3.6.1.4.1.727.7.2.34 | |||
| STR proxyComm | 1.3.6.1.4.1.727.7.2.34.2.1.2 | DisplayString | read-write | The name of the community used to access the proxy agent |
| IP proxyDefaultGateway | 1.3.6.1.4.1.727.7.2.34.2.1.6 | IpAddress | read-write | This is the IP address of the gateway handling routing to all nodes based on ACT'S proprietary NMS |
| proxyEntry | 1.3.6.1.4.1.727.7.2.34.2.1 | not-accessible | This row presents the characteristics that uniquely identifies one proxy board. | |
| INT proxyIndex | 1.3.6.1.4.1.727.7.2.34.2.1.1 | INTEGER | read-only | A unique value for each proxy board. |
| IP proxyIpAddr | 1.3.6.1.4.1.727.7.2.34.2.1.3 | IpAddress | read-write | IP address of this proxy agent |
| IP proxyIpMask | 1.3.6.1.4.1.727.7.2.34.2.1.4 | IpAddress | read-write | IP subnet mask of this proxy agent |
| INT proxyNumber | 1.3.6.1.4.1.727.7.2.34.1 | INTEGER | read-write | Number of proxies in this unit |
| proxyTable | 1.3.6.1.4.1.727.7.2.34.2 | not-accessible | List of proxies in this unit | |
| IP proxyTrapIpAddr | 1.3.6.1.4.1.727.7.2.34.2.1.5 | IpAddress | read-write | Specific IP address to send SNMP trap. |
| pu | 1.3.6.1.4.1.727.7.2.4 | |||
| INT puActive | 1.3.6.1.4.1.727.7.2.4.2.1.3 | INTEGER | read-write | Sets the activation status of the PU. |
| OCT puBanBnnDsap | 1.3.6.1.4.1.727.7.2.4.2.1.41 | OCTET STRING | read-write | For all PU modes with a BAN or BNN connection. Destination SAP that will be used by the remote BAN device for this PU. Valid values are multiples of 4, from 04 to DC. Usually, the SNA destination SAP is 04. |
| INT puBanBnnMaxFrame | 1.3.6.1.4.1.727.7.2.4.2.1.46 | INTEGER | read-write | For all PU modes with a BAN or BNN connection. Maximum frame size on the BAN/BNN side of the connection, excluding BAN/BNN and SNA headers. For an SDLC-BAN connection, if the value of this parameter is equal to that of the puSdlcMaxFrame parameter, then no frame splitting will occur. On the other hand, if the value of this parameter is different from that of the puSdlcMaxFrame parameter, the FRAD will split the frames according to the smaller max frame value. The same is true of a SDLC-BNN, LLC-BAN and LLC-BNN connection. |
| INT puBanBnnNw | 1.3.6.1.4.1.727.7.2.4.2.1.45 | INTEGER | read-write | For all PU modes with a BAN or BNN connection. Number of information frames that are consecutively acknowledged without a retransmission before the window size will be incremented by one. This parameter is used for the dynamic window algorithm, in conjunction with the puBanBnnWindow parameter. |
| INT puBanBnnRetry | 1.3.6.1.4.1.727.7.2.4.2.1.43 | INTEGER | read-write | For all PU modes with a BAN or BNN connection. Maximum number of successive retries on the BAN/BNN side of the connection before the PU is declared inoperative. |
| OCT puBanBnnSsap | 1.3.6.1.4.1.727.7.2.4.2.1.40 | OCTET STRING | read-write | For all PU modes with a BAN or BNN connection. Source SAP (Service Access Point) used by the BayFRAD for this PU. For an BAN-HOST application (BAN side acts as primary unit), the BayFRAD can handle multiple PUs attached to the same host. For this application you must set the BAN/BNN Source SAP parameter to a different value for each PU. Valid values are multiples of 4, from 04 to DC. For an BAN-CONTROLLER application (BAN side acts as secondary unit), this parameter should be set to the default SNA SAP, that is, 04. |
| INT puBanBnnTimeout_ms | 1.3.6.1.4.1.727.7.2.4.2.1.42 | INTEGER | read-write | For all PU modes with a BAN or BNN connection. Wait for reply timeout before retransmitting a frame. This timeout is defined in milliseconds. |
| INT puBanBnnWindow | 1.3.6.1.4.1.727.7.2.4.2.1.44 | INTEGER | read-write | For all PU modes with a BAN or BNN connection. Maximum transmission window size on the BAN. The dynamic window algorithm increases the window size by one each time the number of frames defined by the puBanBnnNw parameter has been acknowledged without a retransmission, until the maximum value defined by the puBanBnnWindow parameter has been reached. The window size is reset to 1 when a retransmission occurs. |
| OCT puBanDa | 1.3.6.1.4.1.727.7.2.4.2.1.39 | OCTET STRING | read-write | For all PU modes with a BAN or BNN connection. Destination address of the device to be reached on the BAN/BNN connection. This address is defined using 12 hexadecimal digits (6 bytes). |
| INT puBanRouting | 1.3.6.1.4.1.727.7.2.4.2.1.47 | INTEGER | read-write | For all PU modes with a BAN or BNN connection. This parameter defines the type of routing required to access the remote station. Select SOURCE for source routing, or TRANSPARENT for transparent routing or SOURCE-A for source routing with an all route broadcast response to a single route broadcast request. |
| INT puBnnFid | 1.3.6.1.4.1.727.7.2.4.2.1.38 | INTEGER | read-write | For all PU modes with a BNN connection. The type of format Identification Field (FID) for this PU. |
| INT puBnnPvc | 1.3.6.1.4.1.727.7.2.4.2.1.37 | INTEGER | read-write | For all PU modes with a BNN connection. The number of the remote PVC to which data from this PU will be sent. |
| INT puDelayBeforeConn_s | 1.3.6.1.4.1.727.7.2.4.2.1.4 | INTEGER | read-write | Delay before connection. Maximum length of time, in seconds, allowed to establish the PU connection or change from one connection status to another. |
| OCT puDlsDa | 1.3.6.1.4.1.727.7.2.4.2.1.24 | OCTET STRING | read-write | For all PU modes with a DLSW connection. Destination address of the device to be reached via a DLSw connection. This address is defined using 12 hexadecimal digits (6 bytes). |
| OCT puDlsDsap | 1.3.6.1.4.1.727.7.2.4.2.1.26 | OCTET STRING | read-write | For all PU modes with a DLSW connection. Destination SAP that will be used by the remote DLSw device for this PU. Valid values are multiples of 4, from 04 to E8. Usually, the SNA destination SAP is 04. |
| IP puDlsIpDst | 1.3.6.1.4.1.727.7.2.4.2.1.28 | IpAddress | read-write | For all PU modes with a DLSW connection. The IP address of the remote PU. This address is a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte. When this parameter is set to 000.000.000.000, no IP address is defined. |
| IP puDlsIpSrc | 1.3.6.1.4.1.727.7.2.4.2.1.27 | IpAddress | read-write | For all PU modes with a DLSW connection. The IP source address, which identifies the port to reach the remote DLS. The port may be the LAN port or one of the serial WAN ports. This address is a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte. When this parameter is set to 000.000.000.000, no IP address is defined. |
| INT puDlsMaxFrame | 1.3.6.1.4.1.727.7.2.4.2.1.29 | INTEGER | read-write | For all PU modes with a DLSW connection. Maximum frame size on the DLSw side of the connection, excluding SNA headers. For an SDLC-DLSW connection, if the value of this parameter is equal to that of the puSdlcMaxFrame parameter, then no frame splitting will occur. On the other hand, if the value of this parameter is different from that of the puSdlcMaxFrame parameter, the unit will split the frames according to the smaller max frame value. The same is true of an LLC-DLSW connection, where the value of puDlsMaxFrame is compared to that of puLlcMaxFrame. |
| OCT puDlsSsap | 1.3.6.1.4.1.727.7.2.4.2.1.25 | OCTET STRING | read-write | For all PU modes with a DLSW connection. Source SAP (Service Access Point) used by the unit for this PU. For a DLSw-HOST application (DLSw side acts as primary unit), the unit can handle multiple PUs over the same pair of network addresses: the host DLSw destination address (DA) and the network address of the unit (NA). To distinguish the PUs attached to the same host, you must set the DLSw SSAP to a different value for each PU. Valid values are multiples of 4, from 04 to E8. This parameter must also be set in the host configuration. For a DLSw-CONTROLLER application (DLSw side acts as secondary unit), this parameter should be set to the default SNA SAP, that is, 04. |
| puEntry | 1.3.6.1.4.1.727.7.2.4.2.1 | not-accessible | This table contains the principal configurable parameters who are used for a particular PU. | |
| INT puIndex | 1.3.6.1.4.1.727.7.2.4.2.1.1 | INTEGER | read-only | A unique value for each PU. Its value ranges between 1 and the value of puNumber. |
| INT puLinkClassNumber | 1.3.6.1.4.1.727.7.2.4.2.1.31 | INTEGER | read-write | The priority class for data from this pu. Classes are defined according to bandwidth weight. |
| STR puLinkRemoteUnit | 1.3.6.1.4.1.727.7.2.4.2.1.30 | DisplayString | read-write | Remote unit to which data from this pu should be directed |
| INT puLinkRemPu | 1.3.6.1.4.1.727.7.2.4.2.1.32 | INTEGER | read-write | For all PU modes with a LINKS connection. The PU number on the remote unit. |
| OCT puLlcDa | 1.3.6.1.4.1.727.7.2.4.2.1.14 | OCTET STRING | read-write | For all PU modes with an LLC connection. Destination address of the device to be reached on the LAN. This address is defined using 12 hexadecimal digits (6 bytes). |
| OCT puLlcDsap | 1.3.6.1.4.1.727.7.2.4.2.1.17 | OCTET STRING | read-write | For all PU modes with an LLC connection. Destination SAP that will be used by the remote LAN device for this PU. Valid values are multiples of 4, from 04 to E8. Usually, the SNA destination SAP is 04. |
| INT puLlcDynamicWindow | 1.3.6.1.4.1.727.7.2.4.2.1.21 | INTEGER | read-write | For all PU modes with an LLC connection. Number of information frames that are consecutively acknowledged without a retransmission before the window size will be incremented by one. This parameter is used for the dynamic window algorithm, in conjunction with the puLlcWindow parameter. |
| INT puLlcMaxFrame | 1.3.6.1.4.1.727.7.2.4.2.1.23 | INTEGER | read-write | For all PU modes with an LLC connection. Maximum frame size on the LLC side of the connection, excluding LLC and SNA headers. For an SDLC-LLC connection, if the value of this parameter is equal to that of the puSdlcMaxFrame parameter, then no frame splitting will occur. On the other hand, if the value of this parameter is different from that of the puSdlcMaxFrame parameter, the unit will split the frames according to the smaller max frame value. The same is true of an LLC-DLSW connection, where the value of puLlcMaxFrame is compared to that of DLS-MAXFRM. |
| INT puLlcRetry | 1.3.6.1.4.1.727.7.2.4.2.1.19 | INTEGER | read-write | For all PU modes with an LLC connection. Maximum number of successive retries on the LLC side of the connection before the PU is declared inoperative. |
| OCT puLlcSsap | 1.3.6.1.4.1.727.7.2.4.2.1.16 | OCTET STRING | read-write | For all PU modes with an LLC connection. Source SAP (Service Access Point) used by the unit for this PU. For an LLC-HOST application (LLC side acts as primary unit), the unit can handle multiple PUs over the same pair of network addresses: the host LAN destination address (DA) and the network address of the unit (NA). To distinguish the PUs attached to the same host, you must set the Source SAP parameter to a different value for each PU. Valid values are multiples of 4, from 04 to E8. This parameter must also be set in the host configuration. For an LLC-CONTROLLER application (LLC side acts as secondary unit), this parameter should be set to the default SNA SAP, that is, 04. |
| INT puLlcTimeout_ms | 1.3.6.1.4.1.727.7.2.4.2.1.18 | INTEGER | read-write | For all PU modes with an LLC connection. Wait for reply timeout before retransmitting a frame. This timeout is defined in milliseconds. |
| INT puLlcTr_Routing | 1.3.6.1.4.1.727.7.2.4.2.1.15 | INTEGER | read-write | For all PU modes with an LLC connection, Token-Ring only. Type of routing used in the Token-Ring LAN. This parameter defines the type of routing required to access the remote station. Select SRC for source routing through the LAN. Select TRSP for transparent routing. |
| INT puLlcWindow | 1.3.6.1.4.1.727.7.2.4.2.1.20 | INTEGER | read-write | For all PU modes with an LLC connection. Maximum transmitter window size on the LAN. The dynamic window algorithm increases the window size by one each time the number of frames defined by the LLC-NW parameter (see below) has been acknowledged without a retransmission, until the maximum value defined by the LLC-WINDOW parameter has been reached. The window size is reset to 1 when a retransmission occurs. |
| INT puMode | 1.3.6.1.4.1.727.7.2.4.2.1.2 | INTEGER | read-write | The PU operating mode. |
| INT puNumber | 1.3.6.1.4.1.727.7.2.4.1 | INTEGER | read-only | The number of controller present on this system. |
| INT puRole | 1.3.6.1.4.1.727.7.2.4.2.1.5 | INTEGER | read-write | For LLC-DLSW, LLC-LINKS and DLSW-LINKS modes only. For LLC-DLSW and LLC-LINKS, this variable indicates whether the LLC side acts as a primary (facing the controller) or secondary (facing the host) unit. The unit automatically defines the other side with the opposite value. For DLSW-LINKS, this variable indicates whether the DLSw side acts as a primary or secondary unit. The unit automatically defines the LINKS side with the opposite value. |
| OCT puSdlcAddress | 1.3.6.1.4.1.727.7.2.4.2.1.7 | OCTET STRING | read-write | For all PU modes with an SDLC connection. SDLC address for the PU on the primary side of the connection. Two hexadecimal digits must be selected. |
| OCT puSdlcAddress2 | 1.3.6.1.4.1.727.7.2.4.2.1.9 | OCTET STRING | read-write | For SDLC-SDLC mode only. SDLC address for the PU on the secondary side of the connection. Two hexadecimal digits must be selected. |
| INT puSdlcMaxFrame | 1.3.6.1.4.1.727.7.2.4.2.1.13 | INTEGER | read-write | For SDLC-LINKS, SDLC-LLC and SDLC-DLSW modes only. Maximum frame size on the SDLC side of the connection, excluding SNA headers. For an SDLC-LLC connection, if the value of this parameter is equal to that of the puLlcMaxFrame parameter, then no frame splitting will occur. On the other hand, if the value of this parameter is different from that of the puLlcMaxFrame parameter, the unit will split the frames according to the smaller max frame value. The same is true of an SDLC-DLSW connection, where the value of puSdlcMaxFrame is compared to that of puDlsMaxFrame. |
| INT puSdlcPort | 1.3.6.1.4.1.727.7.2.4.2.1.6 | INTEGER | read-write | For all PU modes with an SDLC connection. Primary SNA/SDLC port (configured with the P-SDLC protocol) to which the PU is attached. |
| INT puSdlcPort2 | 1.3.6.1.4.1.727.7.2.4.2.1.8 | INTEGER | read-write | For SDLC-SDLC mode only. Secondary port (configured with the S-SDLC protocol) to which the PU is attached. |
| INT puSdlcRetry | 1.3.6.1.4.1.727.7.2.4.2.1.11 | INTEGER | read-write | For all PU modes with an SDLC connection. Maximum number of successive retries on the SDLC side of the connection before the PU is declared inoperative. |
| INT puSdlcTimeout_ms | 1.3.6.1.4.1.727.7.2.4.2.1.10 | INTEGER | read-write | For all PU modes with an SDLC connection. Wait for reply timeout before retransmitting a frame. This timeout is defined in milliseconds. |
| INT puSdlcWindow | 1.3.6.1.4.1.727.7.2.4.2.1.12 | INTEGER | read-write | For all PU modes with an SDLC connection. Transmitter window size. |
| puTable | 1.3.6.1.4.1.727.7.2.4.2 | not-accessible | A list of controller entries. The number of entries is given by the value of puNumber. | |
| INT puXid | 1.3.6.1.4.1.727.7.2.4.2.1.33 | INTEGER | read-write | For SDLC-SDLC and SDLC-LINKS modes only. PU exchanges identification. This parameter determines whether the PU expects to exchange PU identification with the device it is connected to, and ensures the identity of the remote PU in SNA applications. Set to NO if the PU does not support XID. |
| INT puXidFormat | 1.3.6.1.4.1.727.7.2.4.2.1.35 | INTEGER | read-write | For all PU modes with an LLC or DLSW connection. XID format type. Only types 0 and 1 are supported at this time. Type 0 is used by older IBM controllers: the IBM 3274 and some of the old 3174, 5294 and 5394 models. Type 1 is used by the newer models. |
| OCT puXidId | 1.3.6.1.4.1.727.7.2.4.2.1.34 | OCTET STRING | read-write | For all PU modes with an LLC or DLSW connection. This parameter contains the ID block (IDBLK) and ID number (IDNUM) of the PU. The first 3 digits comprise the IDBLK, and the last 5 digits comprise the IDNUM. |
| INT puXidPuType | 1.3.6.1.4.1.727.7.2.4.2.1.36 | INTEGER | read-write | For all PU modes with an LLC or DLSW connection. The PU type that is possible in the XID. Only PU types 1 and 2 are supported at this time. |
| pvc | 1.3.6.1.4.1.727.7.2.10 | |||
| INT pvcBackup | 1.3.6.1.4.1.727.7.2.10.2.1.36 | INTEGER | read-write | Backup PVC can be configured to monitor and backup any link or PCV that fails (ANY) or all links and PVCs (ALL). |
| INT pvcBackupCall_s | 1.3.6.1.4.1.727.7.2.10.2.1.34 | INTEGER | read-write | Delay, in seconds, before activating the backup PVC when a line failure has occurred on a dedicated link or PVC. |
| INT pvcBackupHang_s | 1.3.6.1.4.1.727.7.2.10.2.1.35 | INTEGER | read-write | Delay, in seconds, before deactivating the backup WAN PVC after the dedicated link or PVC has been restored. |
| INT pvcBrgConnection | 1.3.6.1.4.1.727.7.2.10.2.1.19 | INTEGER | read-write | Bridge connection. Set this parameter to YES if the RFC1490-compatible FRAD at the remote end requires bridge frames. If bridge data it not required, a NO value will prevent the transmission of unnecessary frames from this PVC, thus reducing your network costs. |
| INT pvcBroadcastGroup | 1.3.6.1.4.1.727.7.2.10.2.1.18 | INTEGER | read-write | 0 and 1 apply to a pvc in pvcr mode only to specify if its belongs or not to a broadcast group |
| INT pvcBurstInfoRate | 1.3.6.1.4.1.727.7.2.10.2.1.26 | INTEGER | read-write | PVC Burst Information Rate (BIR). The BIR represents the data throughput that the network can accept on this PVC when the network is not congested. |
| INT pvcCompression | 1.3.6.1.4.1.727.7.2.10.2.1.14 | INTEGER | read-write | Use compression on the PVC connection to the remote unit. With compression, the available bandwidth is used more efficiently. When compression is not used, higher speeds can be obtained on the link. |
| INT pvcCost | 1.3.6.1.4.1.727.7.2.10.2.1.10 | INTEGER | read-only | The path cost assigned to the PVC for the Spanning Tree algorithm. This indicates to the automatic single-route bridge function the relative length of the path between the local PVC and the attached LAN. The higher the value, the less preferred the route. |
| INT pvcDialTimeout | 1.3.6.1.4.1.727.7.2.10.2.1.47 | INTEGER | read-write | Wait time, in seconds, allowed to establish a backup pvc using a dial phone number |
| INT pvcDlciAddress | 1.3.6.1.4.1.727.7.2.10.2.1.3 | INTEGER | read-write | The DLCI address of the PVC, representing the virtual connection identification for accessing the remote unit. This address is provided by the carrier. The value 0 is use for the AUTO DLCI. |
| NTF pvcDown | 1.3.6.1.4.1.727.0.602 | This trap indicates that a pvc has come down. | ||
| pvcEntry | 1.3.6.1.4.1.727.7.2.10.2.1 | not-accessible | This table contains the principal configurable parameters who are used for a particular pvc. | |
| STR pvcHuntForwardingAUnit | 1.3.6.1.4.1.727.7.2.10.2.1.49 | DisplayString | read-write | Hunt forwarding group A Unit name. Unit name where a busy call for hunt group A will be forwarded to |
| STR pvcHuntForwardingBUnit | 1.3.6.1.4.1.727.7.2.10.2.1.50 | DisplayString | read-write | Hunt forwarding group B Unit name. Unit name where a busy call for hunt group B will be forwarded to |
| INT pvcIndex | 1.3.6.1.4.1.727.7.2.10.2.1.1 | INTEGER | read-only | A unique value for each pvc. Its value ranges between 1 and the value of pvcNumber. |
| INT pvcInfoRate | 1.3.6.1.4.1.727.7.2.10.2.1.6 | INTEGER | read-write | PVC Committed Information Rate (CIR). The CIR represents the data throughput that the network can accept on this PVC. The CIR, provided by the carrier, must be set on the unit to prevent data loss in the network (frames exceeding the CIR can be discarded). |
| IP pvcIpAddress | 1.3.6.1.4.1.727.7.2.10.2.1.15 | IpAddress | read-write | IP address of the local PVC. This address is a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte. When set to 000.000.000.000, no IP address is defined for this PVC. In this case the unit will use the default IP address defined with the global DEFAULT IP ADDR parameter. |
| INT pvcIpConnection | 1.3.6.1.4.1.727.7.2.10.2.1.20 | INTEGER | read-write | IP connection. Set this parameter to YES if the RFC1490-compatible FRAD at the remote end requires bridge frames. If IP data it not required, a NO value will prevent the transmission of unnecessary frames from this PVC, thus reducing your network costs. |
| INT pvcIpRip | 1.3.6.1.4.1.727.7.2.10.2.1.25 | INTEGER | read-write | When this parameter is set to V1, the RIP routing is done according to the RIP V1 standard. With RIP V2, broadcast or multicast can be used. With RIP V2 MULTICAST, only RIP V2 compliant devices will receive RIP frames. |
| INT pvcIpRipAuthType | 1.3.6.1.4.1.727.7.2.10.2.1.53 | INTEGER | read-write | Enable or disable password authentication for the interface. If you select Simple Password, the password will be included in the sent RIP frames. The received frames containing authentication will be accepted only if the password is valid. |
| STR pvcIpRipPassword | 1.3.6.1.4.1.727.7.2.10.2.1.54 | DisplayString | read-write | This configured data allows the authentication procedure to generate and/or verify the authentication field in the RIP header. This value again must be the same for each interface on each side of the link. |
| INT pvcIpRipTxRx | 1.3.6.1.4.1.727.7.2.10.2.1.52 | INTEGER | read-write | This parameter allows RIP frames transmission only, RIP frames reception only or both transmission and reception of RIP frames. |
| INT pvcIpxConnection | 1.3.6.1.4.1.727.7.2.10.2.1.32 | INTEGER | read-write | IPX connection. Set this parameter to YES if the RFC1490-compatible FRAD at the remote end requires bridge frames. If IPX data it not required, a NO value will prevent the transmission of unnecessary frames from this PVC, thus reducing your network costs. |
| OCT pvcIpxNetNum | 1.3.6.1.4.1.727.7.2.10.2.1.31 | OCTET STRING | read-write | This value identify the IPX network number which the unit is connected to |
| INT pvcIpxRip | 1.3.6.1.4.1.727.7.2.10.2.1.29 | INTEGER | read-write | if this parameter is enable, the unit will generate IPX RIP frame on the port ( the one used by this pvc) every minute, otherwise the unit will discard all IPX RIP frame received and no one will be generated on that port. |
| INT pvcIpxSap | 1.3.6.1.4.1.727.7.2.10.2.1.30 | INTEGER | read-write | if this parameter is enable, the unit will generate IPX SAP frame on the port ( the one used by this pvc) every minute, otherwise the unit will discard all IPX SAP frame received and no one will be generated on that port. |
| INT pvcLlcConnection | 1.3.6.1.4.1.727.7.2.10.2.1.46 | INTEGER | read-write | IPX connection. Set this parameter to YES if the RFC1490-compatible FRAD at the remote end requires bridge frames. If IPX data it not required, a NO value will prevent the transmission of unnecessary frames from this PVC, thus reducing your network costs. |
| INT pvcMaxChannels | 1.3.6.1.4.1.727.7.2.10.2.1.48 | INTEGER | read-write | Indicates the maximum number of voice channels permitted on this PVC. |
| INT pvcMaxFrame | 1.3.6.1.4.1.727.7.2.10.2.1.17 | INTEGER | read-write | Maximum frame size, in octets. This parameter determines the largest datagram that can be sent or received on the interface in one IP frame. Datagrams larger than the maximum frame size are divided into fragments before transmission, the reassembled at the remote end. |
| INT pvcMode | 1.3.6.1.4.1.727.7.2.10.2.1.2 | INTEGER | read-write | Operating mode of PVC. |
| INT pvcNetworkDlci | 1.3.6.1.4.1.727.7.2.10.2.1.28 | INTEGER | read-write | The DLCI address of the PVC on the network side, representing the virtual connection identification on the frame relay interface. |
| INT pvcNetworkPort | 1.3.6.1.4.1.727.7.2.10.2.1.23 | INTEGER | read-write | The Frame Relay network port used by the transparent PVC. The port you select must be configured as a Frame Relay network port (FR-NET protocol) using the port PROTOC parameter. All frames received on the network port side for that PVC will be transmitted to the user port side. |
| INT pvcNumber | 1.3.6.1.4.1.727.7.2.10.1 | INTEGER | read-only | The number of pvc present on this system. |
| IP pvcOspfAreaId | 1.3.6.1.4.1.727.7.2.10.2.1.38 | IpAddress | read-write | Identifies the area to which this PVC belongs. |
| INT pvcOspfDeadInt | 1.3.6.1.4.1.727.7.2.10.2.1.42 | INTEGER | read-write | After ceasing to hear a router's Hello Packets, the number of seconds before its neighbors declare the router down. This is also advertised in the router's Hello Packets in their RouterDeadInterval field. This value again bust be the same for all routers attached to a common network. |
| INT pvcOspfEnable | 1.3.6.1.4.1.727.7.2.10.2.1.37 | INTEGER | read-write | Indicates whether or not OSPF is enabled on this PVC. |
| INT pvcOspfHelloInt | 1.3.6.1.4.1.727.7.2.10.2.1.41 | INTEGER | read-write | The length of time, in seconds, between the Hello Packets that the router sends on the PVC. This value is advertised in the router's Hello Packets. It must be the same for all routers attached to a common network. The smaller the HelloInterval, the faster topological changes will be detected, but more OSPF routing protocol traffic will ensue. |
| INT pvcOspfMetricCost | 1.3.6.1.4.1.727.7.2.10.2.1.44 | INTEGER | read-write | The cost of sending a packet on the PVC expressed in the link state metric. This is advertised as the link cost for this PVC in the router's router links advertisement. |
| STR pvcOspfPassword | 1.3.6.1.4.1.727.7.2.10.2.1.43 | DisplayString | read-write | This configured data allows the authentication procedure to generate and/or verify the authentication field in the OSPF header. This value again must be the same for all routers attached to a common network. |
| INT pvcOspfRetransmitInt | 1.3.6.1.4.1.727.7.2.10.2.1.40 | INTEGER | read-write | The number of seconds between like state advertisement retransmissions for adjacencies belonging to this PVC. Also used when retransmitting Database Description and Link State Request Packets. |
| INT pvcOspfTransitDelay | 1.3.6.1.4.1.727.7.2.10.2.1.39 | INTEGER | read-write | The estimated number of seconds it takes to transmit a Link State Update Packet over this PVC. |
| INT pvcPort | 1.3.6.1.4.1.727.7.2.10.2.1.4 | INTEGER | read-write | Frame Relay port used by the PVC. The port you select must be configured as a FR-USER port, using the port PROTOCOL parameter. |
| INT pvcPriority | 1.3.6.1.4.1.727.7.2.10.2.1.9 | INTEGER | read-only | Priority assigned to the PVC for the Spanning Tree algorithm. |
| INT pvcProxyAddr | 1.3.6.1.4.1.727.7.2.10.2.1.45 | INTEGER | read-write | This variable indicates in what slot of the remote unit (i.e. the SDM-RX unit where this pvc goes) is the SNMP/NMS proxy agent board |
| INT pvcPvcClass | 1.3.6.1.4.1.727.7.2.10.2.1.22 | INTEGER | read-write | The priority class for data from this PVC. Classes are defined according to bandwidth weight. |
| STR pvcRemoteFpUnit | 1.3.6.1.4.1.727.7.2.10.2.1.51 | DisplayString | read-write | Remote FP unit to which data from this PVC should be directed. |
| INT pvcRemotePvc | 1.3.6.1.4.1.727.7.2.10.2.1.21 | INTEGER | read-write | The remote PVC to which data from PVC is sent. Specify the remote PVC number. |
| STR pvcRemoteUnit | 1.3.6.1.4.1.727.7.2.10.2.1.11 | DisplayString | read-write | Remote unit to which data from this PVC should be directed. |
| INT pvcRetry | 1.3.6.1.4.1.727.7.2.10.2.1.13 | INTEGER | read-write | Maximum number of successive retries before the PVC connection is declared down. |
| OCT pvcRingNumber | 1.3.6.1.4.1.727.7.2.10.2.1.24 | OCTET STRING | read-write | The ring number of the remote Token-Ring LAN, required for source routing of Token-Ring data via the unit. |
| IP pvcSubnetMask | 1.3.6.1.4.1.727.7.2.10.2.1.16 | IpAddress | read-write | Subnet mask associated with the PVC's IP address. It is configured like the IP address: a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte. The subnet mask identifies which bits of the IP address correspond to the physical network, and which bits correspond to host identifiers. |
| pvcTable | 1.3.6.1.4.1.727.7.2.10.2 | not-accessible | A list of pvc entries. The number of entries is given by the value of pvcNumber. | |
| INT pvcTimeout_ms | 1.3.6.1.4.1.727.7.2.10.2.1.12 | INTEGER | read-write | The wait for ACK timeout before retransmitting a frame on the PVC. |
| INT pvcType | 1.3.6.1.4.1.727.7.2.10.2.1.33 | INTEGER | read-write | For PVCR mode only. This parameter defines the PVC as a dedicated PVC or a backup PVC. The ANSWER type is used for the PVC that responds to calls. When you install a backup PVC between two units, one unit must be configured in CALL-BACKUP type and the other as ANSWER. |
| NTF pvcUp | 1.3.6.1.4.1.727.0.606 | This trap indicates that a pvc has come up. | ||
| INT pvcUserDlci | 1.3.6.1.4.1.727.7.2.10.2.1.27 | INTEGER | read-write | The DLCI address of the PVC on the user side, representing the virtual connection identification on the frame relay interface. |
| INT pvcUserPort | 1.3.6.1.4.1.727.7.2.10.2.1.5 | INTEGER | read-write | Frame Relay port used by the PVC. The port you select must be configured as a FR-USER port, using the port PROTOCOL parameter. |
| NTF q922Down | 1.3.6.1.4.1.727.0.668 | This trap indicates that a Q922 link has come down. | ||
| NTF q922Up | 1.3.6.1.4.1.727.0.667 | This trap indicates that a Q922 link has come up. | ||
| schedule | 1.3.6.1.4.1.727.7.2.5 | |||
| STR scheduleBeginTime | 1.3.6.1.4.1.727.7.2.5.2.1.4 | DisplayString | read-write | Time of day at which the period begins on a 24-hour clock. When the period is enabled, the WAN link operating mode defined for the period will commence at this time on the configured day(s). |
| INT scheduleDay | 1.3.6.1.4.1.727.7.2.5.2.1.3 | INTEGER | read-write | Day(s) of the week during which the period is effective. Select ALL to configure the period for all days of the week. Use weekend for Saturday and Sunday only. Use workday for Monday to Friday. |
| INT scheduleEnable | 1.3.6.1.4.1.727.7.2.5.2.1.2 | INTEGER | read-write | Enable period. This parameter defines whether the period will be used during the time period it covers. When no periods are enabled, or no enabled period covers the current time, the unit uses the default operating mode configured with the WAN link parameters. |
| STR scheduleEndTime | 1.3.6.1.4.1.727.7.2.5.2.1.5 | DisplayString | read-write | Time of day at which the period ends on a 24-hour clock. When the period is enabled, the WAN link operating mode defined for the period will be disabled at this time on the configured day(s). If no other period is configured and enabled to commence at this time, the unit will activate the default operating mode configured with the WAN link parameters. |
| scheduleEntry | 1.3.6.1.4.1.727.7.2.5.2.1 | not-accessible | This table contains the principal configurable parameters who are used for a particular period. | |
| INT scheduleNumber | 1.3.6.1.4.1.727.7.2.5.1 | INTEGER | read-only | The number of period present on this system. |
| INT schedulePeriod | 1.3.6.1.4.1.727.7.2.5.2.1.1 | INTEGER | read-only | A unique value for each period. Its value ranges between 1 and the value of scheduleNumber. |
| INT schedulePort1 | 1.3.6.1.4.1.727.7.2.5.2.1.6 | INTEGER | read-write | Operating mode for the WAN link (port configured in PVCR protocol) when this period is activated. The possible settings for this parameter are the following: DEDICATED: Communication is carried out over a dedicated line. ANSWER: The port can receive calls only. CALL-BKUP: Call mode using a backup recovery mechanism. The port is activated in case of line failure on the dedicated WAN links. CALL-BOD: Call mode using Bandwidth On Demand(BOND) processing, which automatically controls both dialing over and hanging up the link. INACTIVE: Deactivation of the link. |
| INT schedulePort2 | 1.3.6.1.4.1.727.7.2.5.2.1.7 | INTEGER | read-write | |
| INT schedulePort3 | 1.3.6.1.4.1.727.7.2.5.2.1.8 | INTEGER | read-write | |
| INT schedulePort4 | 1.3.6.1.4.1.727.7.2.5.2.1.9 | INTEGER | read-write | |
| INT schedulePort5 | 1.3.6.1.4.1.727.7.2.5.2.1.10 | INTEGER | read-write | |
| INT schedulePort6 | 1.3.6.1.4.1.727.7.2.5.2.1.11 | INTEGER | read-write | |
| INT schedulePort7 | 1.3.6.1.4.1.727.7.2.5.2.1.12 | INTEGER | read-write | |
| INT schedulePort8 | 1.3.6.1.4.1.727.7.2.5.2.1.13 | INTEGER | read-write | |
| scheduleTable | 1.3.6.1.4.1.727.7.2.5.2 | not-accessible | A list of period entries. The number of entries is given by the value of scheduleNumber. | |
| NTF setupReset | 1.3.6.1.4.1.727.0.623 | The setup was reset by the operator. | ||
| slot | 1.3.6.1.4.1.727.7.2.31 | |||
| INT slotIfIndex | 1.3.6.1.4.1.727.7.2.31.2.1.3 | INTEGER | read-only | A unique value for each interface. Matches exaclty the ifIndex of the ifEntry in RFC-1213 |
| INT slotPortInSlot | 1.3.6.1.4.1.727.7.2.31.2.1.2 | INTEGER | read-only | The logical number of this interface within its slot. |
| slotPortInSlotEntry | 1.3.6.1.4.1.727.7.2.31.2.1 | not-accessible | One element of the above table | |
| slotPortInSlotTable | 1.3.6.1.4.1.727.7.2.31.2 | not-accessible | This table maps a slot/PortInThisSlot coordinate to the corresponding ifIndex (in intfTable and ifTable) | |
| INT slotSlot | 1.3.6.1.4.1.727.7.2.31.2.1.1 | INTEGER | read-only | The localization of this interface, whether on baseCard or in slot, and on what slot |
| stat | 1.3.6.1.4.1.727.7.2.20 | |||
| INT statAlarmAlarm | 1.3.6.1.4.1.727.7.2.20.1.1.6 | INTEGER | read-only | The name of the alarm. |
| INT statAlarmArg | 1.3.6.1.4.1.727.7.2.20.1.1.7 | INTEGER | read-only | An argument permitting to detect the reason of the alarm |
| STR statAlarmDate | 1.3.6.1.4.1.727.7.2.20.1.1.3 | DisplayString | read-only | The date of the alarm. |
| STR statAlarmDesc | 1.3.6.1.4.1.727.7.2.20.1.1.2 | DisplayString | read-only | This variable contains a printable octet string which, if available, gives a short description of the alarm. |
| statAlarmEntry | 1.3.6.1.4.1.727.7.2.20.1.1 | not-accessible | This table contains the list of alarms arrived on the system. | |
| INT statAlarmIndex | 1.3.6.1.4.1.727.7.2.20.1.1.1 | INTEGER | read-only | A unique value for each alarm. Its value ranges between 1 and the value of statAlarmNumber. |
| INT statAlarmModule | 1.3.6.1.4.1.727.7.2.20.1.1.5 | INTEGER | read-only | The module who has detected the alarm. |
| statAlarmTable | 1.3.6.1.4.1.727.7.2.20.1 | not-accessible | The list of alarms for the system. The number of entries is given by the value of StatAlarmNumber. | |
| STR statAlarmTime | 1.3.6.1.4.1.727.7.2.20.1.1.4 | DisplayString | read-only | The time of the alarm. |
| statBootp | 1.3.6.1.4.1.727.7.2.20.21 | |||
| INT statBootpCannotReceiveAndForwardOnTheSamePort | 1.3.6.1.4.1.727.7.2.20.21.12 | INTEGER | read-only | Number of frame received and try to be send on the same port. This will occur when the relay agents are in BROADCAST MODE. In normal operation, when the product is well configured, this should not occur. This frame is discarded. |
| INT statBootpCannotRouteFrame | 1.3.6.1.4.1.727.7.2.20.21.10 | INTEGER | read-only | Configuration problem: in the IP destination address list, which is configurable, we have an address that we cannot route (we don't know on which port transmit the frame). This frame is discarded. |
| INT statBootpFrameTooSmallToBeABootpFrame | 1.3.6.1.4.1.727.7.2.20.21.11 | INTEGER | read-only | The frame have not the minimal length of a BOOTP frame, some fields are missing. This frame is discarded. |
| INT statBootpHopsLimitExceed | 1.3.6.1.4.1.727.7.2.20.21.6 | INTEGER | read-only | A BOOTREQUEST frame was received with its hops count that exceed the configured Max hops. This frame is discarded. |
| INT statBootpInvalidOpCodeField | 1.3.6.1.4.1.727.7.2.20.21.9 | INTEGER | read-only | A frame is received on BOOTPC or BOOTPS port with a invalid operation code field: It was not a BOOTREQUEST nor BOOTREPLY. This frame is discarded. |
| INT statBootpNbReplyReceived | 1.3.6.1.4.1.727.7.2.20.21.3 | INTEGER | read-only | Number of BOOTREPLY frame received |
| INT statBootpNbReplySend | 1.3.6.1.4.1.727.7.2.20.21.4 | INTEGER | read-only | Number of BOOTREPLY frame send |
| INT statBootpNbRequestReceived | 1.3.6.1.4.1.727.7.2.20.21.1 | INTEGER | read-only | Number of BOOTREQUEST frame received |
| INT statBootpNbRequestSend | 1.3.6.1.4.1.727.7.2.20.21.2 | INTEGER | read-only | Number of BOOTREQUEST frame send |
| INT statBootpReplyReceivedOnPortBootpc | 1.3.6.1.4.1.727.7.2.20.21.8 | INTEGER | read-only | A BOOTREPLY frame was received on the UDP port BOOTPC. That could occur when a BOOTP/DHCP server is on the same LAN that we are. But that is considered unusual. This frame is discarded. |
| INT statBootpReplyWithInvalidGiaddr | 1.3.6.1.4.1.727.7.2.20.21.5 | INTEGER | read-only | A BOOTREPLY was received but the giaddr (the gateway IP address) fields do not correspond of any IP address of your ports. This frames is discarded. |
| INT statBootpRequestReceivedOnPortBootpc | 1.3.6.1.4.1.727.7.2.20.21.7 | INTEGER | read-only | A BOOTREQUEST frame was received on the UDP port BOOTPC. That should never occur. This frame is discarded. |
| statBridge | 1.3.6.1.4.1.727.7.2.20.5 | |||
| statBridgeBridge | 1.3.6.1.4.1.727.7.2.20.5.1 | |||
| STR statBridgeBridgeAddressDiscard | 1.3.6.1.4.1.727.7.2.20.5.1.1 | DisplayString | read-only | This counter indicates the number of times that an address entry in the filtering database has been removed to make room for a new address. If this counter increases rapidly, the filtering database is too small for the number of addresses (stations) in the network. |
| STR statBridgeBridgeDesignatedRoot | 1.3.6.1.4.1.727.7.2.20.5.1.3 | DisplayString | read-only | Identifier of the designated root bridge. This is an 8 byte hexadecimal label composed of the bridge priority level (the first 2 bytes) and the address of the adapter connecting the bridge to the LAN segment with the lowest LAN segment number. The root bridge has the lowest bridge identifier of all bridges in the network, and is at the top of the spanning tree. It is also the bridge that sends the 'HELLO' message to detect when other bridges enter and leave the network. The root bridge usually carries the greatest amount of traffic, since it connects the two halves of the network together. |
| STR statBridgeBridgeFrameDiscard | 1.3.6.1.4.1.727.7.2.20.5.1.2 | DisplayString | read-only | This counter indicates the number of times that a frame has not been bridged because its destination is local. |
| STR statBridgeBridgeFrameFiltered | 1.3.6.1.4.1.727.7.2.20.5.1.6 | DisplayString | read-only | This counter indicates the number of frames that are not forwarded because a filter configured on the unit. |
| STR statBridgeBridgeFrameTimeout | 1.3.6.1.4.1.727.7.2.20.5.1.7 | DisplayString | read-only | Number of frames discarded because the transit delay for this frame has been reached. |
| STR statBridgeBridgeRootCost | 1.3.6.1.4.1.727.7.2.20.5.1.4 | DisplayString | read-only | From each unit there are potentially many different paths to the root bridge. The root cost is the lowest path cost, that is, the shortest relative path length to the root bridge. When the root cost is displayed as zero (0), either this unit is the root bridge or there is no direct path from this unit to the root bridge. |
| STR statBridgeBridgeRootPort | 1.3.6.1.4.1.727.7.2.20.5.1.5 | DisplayString | read-only | The root port is the port with the root cost. In other words, it is the port in the direction of the least path cost to the root bridge. The root port is identified by the attached equipment: LAN, Group 1 (GR1) to Group 4 (GR4). NONE indicates that this unit is the root bridge. |
| statBridgePort | 1.3.6.1.4.1.727.7.2.20.5.2 | |||
| STR statBridgePortDesignatedBridge | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.6 | DisplayString | read-only | Identifier of the designated bridge. This is an 8-byte hexadecimal label composed of the bridge priority level (the first 2 bytes) and the address of the adapter connecting the bridge to the LAN segment (or group) with the lowest number. For each LAN segment (or group), only one bridge is in the forwarding state at any one time. This is the designated bridge for that LAN (or group). All other bridges in the network are in the blocking state, and do not forward frames or build address tables. |
| STR statBridgePortDesignatedCost | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.5 | DisplayString | read-only | The cost of the path to the root bridge provided by the designated port (see DESIGNATED PORT parameter, below). The designated port connects to the same LAN as the port being examined. |
| STR statBridgePortDesignatedPort | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.7 | DisplayString | read-only | The port that is considered the designated port for this LAN (the LAN to which the port being examined is connected). All LAN data is sent via this port to the root bridge. The designated port ID is a 2-byte hexadecimal label, where the high byte indicates the port priority and the low byte indicates the port number. |
| STR statBridgePortDesignatedRoot | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.4 | DisplayString | read-only | Identifier of the designated root for this port, that is, the bridge that this port considers to be the root bridge of the network. The bridge ID is an 8-byte hexadecimal label composed of the bridge priority level (the first 2 bytes) and the address of the adapter connecting the bridge to the LAN segment (or group) with the lowest number. |
| STR statBridgePortDestination | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.2 | DisplayString | read-only | Destination of this port. When the bridge port is the LAN, the displayed destination is always LOCAL LAN. For the other bridge ports the dispayed destination is the name of the attached remote unit. |
| statBridgePortEntry | 1.3.6.1.4.1.727.7.2.20.5.2.1.1 | not-accessible | This table contains the principal statistics for the BridgePort. | |
| INT statBridgePortIndex | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.1 | INTEGER | read-only | A unique value for each port. Its value ranges between 1 and the value of groupNumber+iflanNumber. |
| STR statBridgePortState | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.3 | DisplayString | read-only | Current state of the LAN port (or group) in the bridge topology. This state can be one of the following: DISABLED: Not participating in the bridge topology BLOCKING: Participation limited to ensuring that another bridge forwards frames onto the network segment LISTENING: Participates in the spanning tree algorithm LEARNING: Participates in the spanning tree algorithm and builds address tables FORWARD: Participates in the spanning tree algorithm, builds address tables and forwards frames |
| statBridgePortTable | 1.3.6.1.4.1.727.7.2.20.5.2.1 | not-accessible | A list of statistic entries for the BridgePort. | |
| STR statBridgePortTr_AllRteFrameIn | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.12 | DisplayString | read-only | Number of all-routes broadcast frames received on the port. This statistic is displayed for a source routing bridge only. |
| STR statBridgePortTr_AllRteFrameOut | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.13 | DisplayString | read-only | Number of all-routes broadcast frames forwarded from the port. This statistic is displayed for a source routing bridge only. |
| STR statBridgePortTr_FrmLngExceeded | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.19 | DisplayString | read-only | This counter displays the number of non-broadcast token-ring frames that have been discarded by this port because the frame length has passed the maximum length permitted. |
| STR statBridgePortTr_HopCntExceeded | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.18 | DisplayString | read-only | Number of single-route or all-routes broadcast frames that have been discarded by this port because the Routing Information field reached the maximum number of hops permitted. This statistic is displayed for a source routing bridge only. |
| STR statBridgePortTr_SegmentDuplicate | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.17 | DisplayString | read-only | Number of frames, other than broadcast frames, that have been discarded by this port because the Routing Information field contained the same segment identifier more than once. This statistic is displayed for a source routing bridge only. |
| STR statBridgePortTr_SegmentMismatch | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.16 | DisplayString | read-only | Number of single-route or all-routes broadcast frames that have been discarded by this port because the Routing Information field contained an invalid adjacent segment value. This statistic is displayed for a source routing bridge only. |
| STR statBridgePortTr_SingleRteFrameIn | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.14 | DisplayString | read-only | Number of single-route broadcast frames received on the port. This statistic is displayed for a source routing bridge only. |
| STR statBridgePortTr_SingleRteFrameOut | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.15 | DisplayString | read-only | Number of single-route broadcast frames forwarded from the port. This statistic is displayed for a source routing bridge only. |
| STR statBridgePortTr_SpecRteFrameIn | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.10 | DisplayString | read-only | Number of frames received on the port that contain a Routing Information field (other than broadcast frames). This statistic is displayed for a source routing bridge only. |
| STR statBridgePortTr_SpecRteFrameOut | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.11 | DisplayString | read-only | Number of frames forwarded from the port that contain a Routing Information field (other than broadcast frames). This statistic is displayed for a source routing bridge only. |
| STR statBridgePortTrspFrameIn | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.8 | DisplayString | read-only | Number of frames received on the port for a transparent bridge. |
| STR statBridgePortTrspFrameOut | 1.3.6.1.4.1.727.7.2.20.5.2.1.1.9 | DisplayString | read-only | Number of frames forwarded from the port for a transparent bridge. |
| INT statEstablishIndications | 1.3.6.1.4.1.727.7.2.20.24.3 | INTEGER | read-only | Number of establish indications. |
| statGrp | 1.3.6.1.4.1.727.7.2.20.22 | |||
| STR statGrpDestName | 1.3.6.1.4.1.727.7.2.20.22.2.1.2 | DisplayString | read-only | The destination name of the group |
| statGrpEntry | 1.3.6.1.4.1.727.7.2.20.22.2.1 | not-accessible | This table contains the principal statistics for the groups. | |
| INT statGrpIndex | 1.3.6.1.4.1.727.7.2.20.22.2.1.1 | INTEGER | read-only | A unique value for each group. Its value ranges between 1 and the number of groups. |
| INT statGrpNumber | 1.3.6.1.4.1.727.7.2.20.22.1 | INTEGER | read-only | A list of statistic entries for the groups. |
| INT statGrpOutOfSeqErrs | 1.3.6.1.4.1.727.7.2.20.22.2.1.3 | INTEGER | read-only | |
| INT statGrpSorterOverruns | 1.3.6.1.4.1.727.7.2.20.22.2.1.5 | INTEGER | read-only | |
| INT statGrpSorterTimeouts | 1.3.6.1.4.1.727.7.2.20.22.2.1.4 | INTEGER | read-only | |
| statGrpTable | 1.3.6.1.4.1.727.7.2.20.22.2 | not-accessible | A list of statistic entries for the groups. | |
| STR statIfcemClockState | 1.3.6.1.4.1.727.7.2.20.28.1.3 | DisplayString | read-only | This variable contains the status of the clock extracting module. |
| STR statIfcemDesc | 1.3.6.1.4.1.727.7.2.20.28.1.2 | DisplayString | read-only | A textual string containing information about a specific interface. |
| statIfcemEntry | 1.3.6.1.4.1.727.7.2.20.28.1 | not-accessible | This table contains statistics for the cem interfaces. | |
| INT statIfcemIndex | 1.3.6.1.4.1.727.7.2.20.28.1.1 | INTEGER | read-only | A unique value for each interface. |
| statIfcemTable | 1.3.6.1.4.1.727.7.2.20.28 | not-accessible | A list of statistic entries for the cem interfaces. | |
| STR statIflanBadFlags | 1.3.6.1.4.1.727.7.2.20.3.1.13 | DisplayString | read-only | These flags are to find the reason of bad frames received. U : Bad length Q : Overflow F : Flush S : Overrun B : Bad CRC A : Abort |
| CTR statIflanBadFrames | 1.3.6.1.4.1.727.7.2.20.3.1.12 | Counter | read-only | The number of bad frames received. |
| STR statIflanConnectionStatus | 1.3.6.1.4.1.727.7.2.20.3.1.4 | DisplayString | read-only | The logical connection status of the lan connection. |
| statIflanEntry | 1.3.6.1.4.1.727.7.2.20.3.1 | not-accessible | This table contains the principal statistics for the lan interfaces. | |
| STR statIflanEth_Interface | 1.3.6.1.4.1.727.7.2.20.3.1.6 | DisplayString | read-only | The interface used by ethernet. |
| CTR statIflanEthAlign | 1.3.6.1.4.1.727.7.2.20.3.1.22 | Counter | read-only | Alignment errors. This counter displays the number of incomplete frames received on the Ethernet port that do not pass the CRC check. |
| CTR statIflanEthCarrierSense | 1.3.6.1.4.1.727.7.2.20.3.1.23 | Counter | read-only | Carrier sense errors. This counter indicates the number of frames transmitted with carrier sense errors: either the carrier sense signal from the physical layer interface was not asserted, or it was unasserted during transmission of the frame without collision. |
| CTR statIflanEthDeferredTrans | 1.3.6.1.4.1.727.7.2.20.3.1.18 | Counter | read-only | This counter contains the Number of frames deferred before transmission. |
| CTR statIflanEthExcessiveCollision | 1.3.6.1.4.1.727.7.2.20.3.1.19 | Counter | read-only | Excessive collisions. This counter displays the number of frames aborted during transmission due to an excessive number of collisions. These are frames that have not been transmitted successfully. |
| CTR statIflanEthFrameCheckSeq | 1.3.6.1.4.1.727.7.2.20.3.1.21 | Counter | read-only | Frame check sequence errors. This counter displays the number of frames received on the Ethernet port with FCS errors. |
| CTR statIflanEthLateCollision | 1.3.6.1.4.1.727.7.2.20.3.1.20 | Counter | read-only | Late collisions. This counter displays the number of transmit frames with late collision, that is, the number of times that a collision was detected later than 512 bits into the transmitted packet. |
| CTR statIflanEthOneCollision | 1.3.6.1.4.1.727.7.2.20.3.1.15 | Counter | read-only | The number of one collision. |
| CTR statIflanEthThreeAndMoreCol | 1.3.6.1.4.1.727.7.2.20.3.1.17 | Counter | read-only | The number of three and more collisions. |
| CTR statIflanEthTwoCollisions | 1.3.6.1.4.1.727.7.2.20.3.1.16 | Counter | read-only | The number of two collisions. |
| INT statIflanIndex | 1.3.6.1.4.1.727.7.2.20.3.1.1 | INTEGER | read-only | A unique value for each interface. |
| GAU statIflanMeanRx_kbps | 1.3.6.1.4.1.727.7.2.20.3.1.8 | Gauge | read-only | This is the average throughput for data received from the LAN. |
| GAU statIflanMeanTx_kbps | 1.3.6.1.4.1.727.7.2.20.3.1.7 | Gauge | read-only | This is the average throughput for transmissions sent to the LAN. |
| STR statIflanOperatingMode | 1.3.6.1.4.1.727.7.2.20.3.1.5 | DisplayString | read-only | The operating mode of the lan connection. |
| GAU statIflanPeakRx_kbps | 1.3.6.1.4.1.727.7.2.20.3.1.10 | Gauge | read-only | This is the maximum throughput for data received from the LAN. |
| GAU statIflanPeakTx_kbps | 1.3.6.1.4.1.727.7.2.20.3.1.9 | Gauge | read-only | This is the maximum throughput for transmissions sent to the LAN. |
| INT statIflanProtocol | 1.3.6.1.4.1.727.7.2.20.3.1.2 | INTEGER | read-only | The operating mode of the lan connection. |
| CTR statIflanRetries | 1.3.6.1.4.1.727.7.2.20.3.1.11 | Counter | read-only | The number of retries is incremented when there is a retransmission between the system and the controller or host. |
| INT statIflanSpeed | 1.3.6.1.4.1.727.7.2.20.3.1.3 | INTEGER | read-only | This variable contains the speed measured by the system. |
| statIflanTable | 1.3.6.1.4.1.727.7.2.20.3 | not-accessible | A list of statistic entries for the lan interfaces. The number of entries is given by the value of iflanNumber. | |
| CTR statIflanTrReceiveCongestion | 1.3.6.1.4.1.727.7.2.20.3.1.14 | Counter | read-only | This counter contains the number of times the receiver has overrun. Token-Ring only. |
| STR statIfvceDesc | 1.3.6.1.4.1.727.7.2.20.10.1.2 | DisplayString | read-only | A textual string containing information about a specific interface. |
| STR statIfvceDvcPortInUse | 1.3.6.1.4.1.727.7.2.20.10.1.10 | DisplayString | read-only | Indicates the logical port number that is being used by an active voice connection. For CCS protocols such as QSIG, the E1/CCS card selects which DSP on which DVC card it will use for a connection. The logical port number corresponding to the DSP is reported to the NetPerformer baseboard, and comprises the value of the DVC Port In Use statistic. For slot 1 of the DVC card the possible values are 100 to 106, for slot 2 they are 200 to 206, and so on. |
| statIfvceEntry | 1.3.6.1.4.1.727.7.2.20.10.1 | not-accessible | This table contains the principal statistics for the voice interfaces. | |
| INT statIfvceFaxMode | 1.3.6.1.4.1.727.7.2.20.10.1.7 | INTEGER | read-only | Indicates the current voice compression rate. The possible rates are 4.8 Kbps and 8 Kbps. |
| INT statIfvceFaxRate | 1.3.6.1.4.1.727.7.2.20.10.1.6 | INTEGER | read-only | Indicates the current voice compression rate. The possible rates are 4.8 Kbps and 8 Kbps. |
| INT statIfvceIndex | 1.3.6.1.4.1.727.7.2.20.10.1.1 | INTEGER | read-only | A unique value for each interface: the same value as the ifIndex in RFC1213 that refers to this voice port |
| INT statIfvceLastError | 1.3.6.1.4.1.727.7.2.20.10.1.5 | INTEGER | read-only | The last error occurred for this port. |
| CTR statIfvceOverruns | 1.3.6.1.4.1.727.7.2.20.10.1.8 | Counter | read-only | The number of receive overruns that have occurred. |
| INT statIfvceProtocol | 1.3.6.1.4.1.727.7.2.20.10.1.4 | INTEGER | read-only | Indicates the current protocol setting the port. |
| INT statIfvceState | 1.3.6.1.4.1.727.7.2.20.10.1.3 | INTEGER | read-only | Indicates the current logical state of the port. |
| statIfvceTable | 1.3.6.1.4.1.727.7.2.20.10 | not-accessible | A list of statistic entries for the voice interfaces. The number of entries is given by the value of ifNumber. | |
| CTR statIfvceUnderruns | 1.3.6.1.4.1.727.7.2.20.10.1.9 | Counter | read-only | The number of transmit underruns that have occurred. |
| STR statIfwanBadFlags | 1.3.6.1.4.1.727.7.2.20.2.1.13 | DisplayString | read-only | These flags are to find the reason of bad frames received. U : Bad length Q : Overflow F : Flush S : Overrun B : Bad CRC A : Abort |
| CTR statIfwanBadFrames | 1.3.6.1.4.1.727.7.2.20.2.1.12 | Counter | read-only | The number of bad frames received. |
| CTR statIfwanBadOctets | 1.3.6.1.4.1.727.7.2.20.2.1.22 | Counter | read-only | The number of characters received and deleted because of a bad frame. |
| CTR statIfwanChAborts | 1.3.6.1.4.1.727.7.2.20.2.1.36 | Counter | read-only | The number of frames aborted received |
| CTR statIfwanChOverflows | 1.3.6.1.4.1.727.7.2.20.2.1.35 | Counter | read-only | The number of channel overflows |
| CTR statIfwanChSeqErrs | 1.3.6.1.4.1.727.7.2.20.2.1.37 | Counter | read-only | The number of frames reception failure due to at least one missing block |
| CTR statIfwanCompErrs | 1.3.6.1.4.1.727.7.2.20.2.1.34 | Counter | read-only | The number of compression errors |
| STR statIfwanDesc | 1.3.6.1.4.1.727.7.2.20.2.1.2 | DisplayString | read-only | A textual string containing information about a specific interface. |
| STR statIfwanDropInsert | 1.3.6.1.4.1.727.7.2.20.2.1.38 | DisplayString | read-only | Drop and Insert status. |
| statIfwanEntry | 1.3.6.1.4.1.727.7.2.20.2.1 | not-accessible | This table contains the principal statistics for the wan interfaces. | |
| CTR statIfwanFramesRx | 1.3.6.1.4.1.727.7.2.20.2.1.18 | Counter | read-only | The number of frames received |
| CTR statIfwanFramesTx | 1.3.6.1.4.1.727.7.2.20.2.1.17 | Counter | read-only | The number of frames transmitted |
| INT statIfwanIndex | 1.3.6.1.4.1.727.7.2.20.2.1.1 | INTEGER | read-only | A unique value for each interface. |
| STR statIfwanInterface | 1.3.6.1.4.1.727.7.2.20.2.1.4 | DisplayString | read-only | The actual interface used on the port. |
| GAU statIfwanMeanRx | 1.3.6.1.4.1.727.7.2.20.2.1.9 | Gauge | read-only | This variable contains the average line usage for data received on the wan port. |
| GAU statIfwanMeanTx | 1.3.6.1.4.1.727.7.2.20.2.1.8 | Gauge | read-only | This variable contains the average line usage for transmissions on the wan port. |
| STR statIfwanModemSignal | 1.3.6.1.4.1.727.7.2.20.2.1.5 | DisplayString | read-only | This variable contains the modem signal status. |
| CTR statIfwanOctetsRx | 1.3.6.1.4.1.727.7.2.20.2.1.20 | Counter | read-only | The number of octets received |
| CTR statIfwanOctetsTx | 1.3.6.1.4.1.727.7.2.20.2.1.19 | Counter | read-only | The number of octets transmitted |
| CTR statIfwanOvrFrames | 1.3.6.1.4.1.727.7.2.20.2.1.21 | Counter | read-only | The number of frames received and deleted because the input queue is full. |
| CTR statIfwanOvrOctets | 1.3.6.1.4.1.727.7.2.20.2.1.23 | Counter | read-only | The number of characters received and deleted because the input queue is full. |
| GAU statIfwanPeakRx | 1.3.6.1.4.1.727.7.2.20.2.1.11 | Gauge | read-only | This variable contains the maximum line usage for data received on the wan port. |
| GAU statIfwanPeakTx | 1.3.6.1.4.1.727.7.2.20.2.1.10 | Gauge | read-only | This variable contains the maximum line usage for transmissions on the wan port. |
| INT statIfwanProtocol | 1.3.6.1.4.1.727.7.2.20.2.1.3 | INTEGER | read-only | The operating mode of the wan interface. |
| STR statIfwanQ922State | 1.3.6.1.4.1.727.7.2.20.2.1.41 | DisplayString | read-only | Q922 state of the port if SVC's are enabled. Only on FR-USER ports. |
| CTR statIfwanRestart | 1.3.6.1.4.1.727.7.2.20.2.1.16 | Counter | read-only | The number of restarts. For a user port this counter is incremented every time an error on the link caused the port to restart. These errors occur over the link, not between equipment. The number of restarts is not calculated for user ports in P-SDLC or S-SDLC. |
| CTR statIfwanRetries | 1.3.6.1.4.1.727.7.2.20.2.1.15 | Counter | read-only | The number of retries is incremented when there is a retransmission between the system and the controller or host. |
| INT statIfwanSpeed | 1.3.6.1.4.1.727.7.2.20.2.1.6 | INTEGER | read-only | This variable contains the speed measured by the system. |
| STR statIfwanState | 1.3.6.1.4.1.727.7.2.20.2.1.7 | DisplayString | read-only | This variable contains the status of the port. |
| CTR statIfwanT1E1BES | 1.3.6.1.4.1.727.7.2.20.2.1.31 | Counter | read-only | The number of BES |
| CTR statIfwanT1E1CSS | 1.3.6.1.4.1.727.7.2.20.2.1.28 | Counter | read-only | The number of CSS |
| CTR statIfwanT1E1DM | 1.3.6.1.4.1.727.7.2.20.2.1.32 | Counter | read-only | The number of DM |
| CTR statIfwanT1E1ESS | 1.3.6.1.4.1.727.7.2.20.2.1.24 | Counter | read-only | The number of ESS |
| CTR statIfwanT1E1LCV | 1.3.6.1.4.1.727.7.2.20.2.1.33 | Counter | read-only | The number of LCV |
| CTR statIfwanT1E1LES | 1.3.6.1.4.1.727.7.2.20.2.1.30 | Counter | read-only | The number of LES |
| CTR statIfwanT1E1PCV | 1.3.6.1.4.1.727.7.2.20.2.1.29 | Counter | read-only | The number of PCV |
| CTR statIfwanT1E1SEF | 1.3.6.1.4.1.727.7.2.20.2.1.26 | Counter | read-only | The number of SEF |
| CTR statIfwanT1E1SES | 1.3.6.1.4.1.727.7.2.20.2.1.25 | Counter | read-only | The number of SES |
| CTR statIfwanT1E1UAS | 1.3.6.1.4.1.727.7.2.20.2.1.27 | Counter | read-only | +The number of UAS |
| statIfwanTable | 1.3.6.1.4.1.727.7.2.20.2 | not-accessible | A list of statistic entries for the wan interfaces. The number of entries is given by the value of ifwanNumber. | |
| STR statIfwanTrspLastError | 1.3.6.1.4.1.727.7.2.20.2.1.40 | DisplayString | read-only | The last error occurred for this port. |
| STR statIfwanTrspState | 1.3.6.1.4.1.727.7.2.20.2.1.39 | DisplayString | read-only | Indicates the current logical state of the port. |
| CTR statIfwanUnderruns | 1.3.6.1.4.1.727.7.2.20.2.1.14 | Counter | read-only | The number of underruns. |
| INT statInvalidRxSizes | 1.3.6.1.4.1.727.7.2.20.25.1 | INTEGER | read-only | Number of frames with invalid lengths. |
| INT statLinkEstablished | 1.3.6.1.4.1.727.7.2.20.24.4 | INTEGER | read-only | Number of links established. |
| INT statMissingControlBlocks | 1.3.6.1.4.1.727.7.2.20.25.2 | INTEGER | read-only | Number of frames without control blocks. |
| INT statProtocolTimeouts | 1.3.6.1.4.1.727.7.2.20.26.17 | INTEGER | read-only | Number of protocol time-outs. |
| CTR statPuChAborts | 1.3.6.1.4.1.727.7.2.20.4.1.6 | Counter | read-only | The number of frames aborted received |
| CTR statPuChOverflows | 1.3.6.1.4.1.727.7.2.20.4.1.5 | Counter | read-only | The number of channel overflows |
| CTR statPuChSeqErrs | 1.3.6.1.4.1.727.7.2.20.4.1.7 | Counter | read-only | The number of frames reception failure due to at least one missing block |
| CTR statPuCompErrs | 1.3.6.1.4.1.727.7.2.20.4.1.4 | Counter | read-only | The number of compression errors |
| STR statPuConnectionStatus | 1.3.6.1.4.1.727.7.2.20.4.1.3 | DisplayString | read-only | This variable contains the status of the connection as a whole. |
| statPuEntry | 1.3.6.1.4.1.727.7.2.20.4.1 | not-accessible | This table contains the principal statistics for the PUs. | |
| INT statPuIndex | 1.3.6.1.4.1.727.7.2.20.4.1.1 | INTEGER | read-only | A unique value for each PU. Its value ranges between 1 and the value of PuNumber. |
| INT statPuMode | 1.3.6.1.4.1.727.7.2.20.4.1.2 | INTEGER | read-only | The PU operating mode. |
| statPuTable | 1.3.6.1.4.1.727.7.2.20.4 | not-accessible | A list of statistic entries for the PUs. The number of entries is given by the value of puNumber. | |
| CTR statPvcBadFrames | 1.3.6.1.4.1.727.7.2.20.6.1.17 | Counter | read-only | The number of frames received and deleted because the input queue is full. |
| CTR statPvcBadOctets | 1.3.6.1.4.1.727.7.2.20.6.1.19 | Counter | read-only | The number of characters received and deleted because of a bad frame. |
| CTR statPvcChAborts | 1.3.6.1.4.1.727.7.2.20.6.1.30 | Counter | read-only | The number of frames aborted received |
| CTR statPvcChOverflows | 1.3.6.1.4.1.727.7.2.20.6.1.29 | Counter | read-only | The number of channel overflows |
| CTR statPvcChSeqErrs | 1.3.6.1.4.1.727.7.2.20.6.1.31 | Counter | read-only | The number of frames reception failure due to at least one missing block |
| CTR statPvcCompErrs | 1.3.6.1.4.1.727.7.2.20.6.1.28 | Counter | read-only | The number of compression errors |
| INT statPvcDlci | 1.3.6.1.4.1.727.7.2.20.6.1.21 | INTEGER | read-only | The current DLCI used by this PVC |
| statPvcEntry | 1.3.6.1.4.1.727.7.2.20.6.1 | not-accessible | This table contains the principal statistics for the PVCs. | |
| CTR statPvcError | 1.3.6.1.4.1.727.7.2.20.6.1.11 | Counter | read-only | Number of errors on the PVC. This counter is incremented every time the unit detects an error coming from the PVC. |
| CTR statPvcFramesRx | 1.3.6.1.4.1.727.7.2.20.6.1.14 | Counter | read-only | The number of frames received |
| CTR statPvcFramesTx | 1.3.6.1.4.1.727.7.2.20.6.1.13 | Counter | read-only | The number of frames transmitted |
| INT statPvcIndex | 1.3.6.1.4.1.727.7.2.20.6.1.1 | INTEGER | read-only | A unique value for each PVC. Its value ranges between 1 and the value of pvcNumber. |
| STR statPvcInfoSignal | 1.3.6.1.4.1.727.7.2.20.6.1.4 | DisplayString | read-only | The information signal status is displayed with a five-character field, where the individual characters have the following meaning: N = New PVC A = Active PVC C = CIR reached F = Forward congestion (to destination PVC) B = Backward congestion (from destination PVC) When an information status signal is not present, the unit displays a dash [-] in the appropriate position. |
| GAU statPvcMeanRx | 1.3.6.1.4.1.727.7.2.20.6.1.8 | Gauge | read-only | The mean bandwidth usage for data received from the destination PVC. |
| GAU statPvcMeanTx | 1.3.6.1.4.1.727.7.2.20.6.1.7 | Gauge | read-only | The mean bandwidth usage for transmissions to the destination PVC. |
| STR statPvcMode | 1.3.6.1.4.1.727.7.2.20.6.1.3 | DisplayString | read-only | The mode used (PVCR or OFF). |
| CTR statPvcOctetsRx | 1.3.6.1.4.1.727.7.2.20.6.1.16 | Counter | read-only | The number of octets received |
| CTR statPvcOctetsTx | 1.3.6.1.4.1.727.7.2.20.6.1.15 | Counter | read-only | The number of octets transmitted |
| CTR statPvcOvrFrames | 1.3.6.1.4.1.727.7.2.20.6.1.18 | Counter | read-only | The number of frames received and deleted because the input queue is full. |
| CTR statPvcOvrOctets | 1.3.6.1.4.1.727.7.2.20.6.1.20 | Counter | read-only | The number of characters received and deleted because the input queue is full. |
| GAU statPvcPeakRx | 1.3.6.1.4.1.727.7.2.20.6.1.10 | Gauge | read-only | The peak bandwidth usage for data received from the destination PVC. |
| GAU statPvcPeakTx | 1.3.6.1.4.1.727.7.2.20.6.1.9 | Gauge | read-only | The peak bandwidth usage for transmissions to the destination PVC. |
| STR statPvcProtocol | 1.3.6.1.4.1.727.7.2.20.6.1.2 | DisplayString | read-only | PVC protocol. |
| CTR statPvcRestart | 1.3.6.1.4.1.727.7.2.20.6.1.12 | Counter | read-only | Number of restarts on the PVC. This counter is incremented every time the link is down for at least 1 second. In addition, if the PVC is not restored within the LINK TIMEOUT value (a Global configuration parameter), the unit will log a LINK PVC DOWN alarm. |
| INT statPvcrRouteAge | 1.3.6.1.4.1.727.7.2.20.7.1.6 | INTEGER | read-only | The AGE statistic gives the number of seconds since the entry for this destination was entered on the routing table, the aging time for the entry. For a valid connection (VALID = YES), the time is normally between 0 and 30 seconds. If the destination is reached |
| statPvcrRouteEntry | 1.3.6.1.4.1.727.7.2.20.7.1 | not-accessible | This table contains the principal statistics for the unit route | |
| INT statPvcrRouteIntrf | 1.3.6.1.4.1.727.7.2.20.7.1.4 | INTEGER | read-only | The interface used to reach the destination. |
| GAU statPvcrRouteMetric | 1.3.6.1.4.1.727.7.2.20.7.1.3 | Gauge | read-only | The METRIC provides the hop count, or number of units that must be passed over to reach the destination. When at 0, it indicates a direct connection to the destination. Its value is usually between 1 and 15 for an indirect connection. When at 16, it indicates that the destination is unreachable. |
| STR statPvcrRouteName | 1.3.6.1.4.1.727.7.2.20.7.1.1 | DisplayString | read-only | A unique value for each unit routing entry. |
| STR statPvcrRouteNextHop | 1.3.6.1.4.1.727.7.2.20.7.1.5 | DisplayString | read-only | The next unit to be reached on the path to the final destination. The next hop is identified by the IP address of the router that will be used to send the IP frame. |
| statPvcrRouteTable | 1.3.6.1.4.1.727.7.2.20.7 | not-accessible | A list of statistic entries for the unit routing. | |
| INT statPvcrRouteValid | 1.3.6.1.4.1.727.7.2.20.7.1.2 | INTEGER | read-only | The VALID value (YES or NO) indicates whether the connection to this destination is currently active. |
| STR statPvcSpeed | 1.3.6.1.4.1.727.7.2.20.6.1.5 | DisplayString | read-only | The port speed measured by the unit. |
| STR statPvcState | 1.3.6.1.4.1.727.7.2.20.6.1.6 | DisplayString | read-only | The possible states for a PVC in PVCR mode are: OFF = PVC inactive CALL = Waiting for active signal from the network TEST = PVC in test mode DATA = PVC in operation |
| statPvcTable | 1.3.6.1.4.1.727.7.2.20.6 | not-accessible | A list of statistic entries for the PVCs. The number of entries is given by the value of pvcNumber. | |
| statQ922counters | 1.3.6.1.4.1.727.7.2.20.24 | |||
| statQ922errors | 1.3.6.1.4.1.727.7.2.20.25 | |||
| statQ933counters | 1.3.6.1.4.1.727.7.2.20.26 | |||
| INT statReleaseIndications | 1.3.6.1.4.1.727.7.2.20.24.2 | INTEGER | read-only | Number of release indications. |
| INT statRxAcknowledgeExpiry | 1.3.6.1.4.1.727.7.2.20.25.3 | INTEGER | read-only | Number of RR ack Tx from Tack expiry. |
| INT statRxBytes | 1.3.6.1.4.1.727.7.2.20.24.8 | INTEGER | read-only | Number of received bytes. |
| INT statRxCallProceedingMessages | 1.3.6.1.4.1.727.7.2.20.26.4 | INTEGER | read-only | Number of received call proceeding messages. |
| INT statRxConnectMessages | 1.3.6.1.4.1.727.7.2.20.26.6 | INTEGER | read-only | Number of Rx connect messages. |
| INT statRxDisconnectMessages | 1.3.6.1.4.1.727.7.2.20.26.12 | INTEGER | read-only | Number of received disconnect messages. |
| INT statRxframes | 1.3.6.1.4.1.727.7.2.20.24.6 | INTEGER | read-only | Number of received frames. |
| INT statRxReleaseCompleteMessages | 1.3.6.1.4.1.727.7.2.20.26.10 | INTEGER | read-only | Number of received release complete messages. |
| INT statRxReleaseMessages | 1.3.6.1.4.1.727.7.2.20.26.8 | INTEGER | read-only | Number of received release messages. |
| INT statRxSetupMessages | 1.3.6.1.4.1.727.7.2.20.26.2 | INTEGER | read-only | Number of received setup messages. |
| INT statRxStatusEnquiryMessages | 1.3.6.1.4.1.727.7.2.20.26.16 | INTEGER | read-only | Number of received status enquiry messages. |
| INT statRxStatusMessages | 1.3.6.1.4.1.727.7.2.20.26.14 | INTEGER | read-only | Number of received status messages. |
| CTR statSvcBadFrames | 1.3.6.1.4.1.727.7.2.20.27.1.17 | Counter | read-only | The number of frames received and deleted because the input queue is full. |
| CTR statSvcBadOctets | 1.3.6.1.4.1.727.7.2.20.27.1.19 | Counter | read-only | The number of characters received and deleted because of a bad frame. |
| INT statSvcDlci | 1.3.6.1.4.1.727.7.2.20.27.1.21 | INTEGER | read-only | The current DLCI used by this SVC |
| statSvcEntry | 1.3.6.1.4.1.727.7.2.20.27.1 | not-accessible | This table contains the principal statistics for the SVCs. | |
| CTR statSvcError | 1.3.6.1.4.1.727.7.2.20.27.1.11 | Counter | read-only | Number of errors on the SVC. This counter is incremented every time the unit detects an error coming from the SVC. |
| CTR statSvcFramesRx | 1.3.6.1.4.1.727.7.2.20.27.1.14 | Counter | read-only | The number of frames received |
| CTR statSvcFramesTx | 1.3.6.1.4.1.727.7.2.20.27.1.13 | Counter | read-only | The number of frames transmitted |
| INT statSvcIndex | 1.3.6.1.4.1.727.7.2.20.27.1.1 | INTEGER | read-only | A unique value for each SVC. |
| STR statSvcInfoSignal | 1.3.6.1.4.1.727.7.2.20.27.1.4 | DisplayString | read-only | The information signal status is displayed with a five-character field, where the individual characters have the following meaning: N = New SVC A = Active SVC C = CIR reached F = Forward congestion (to destination SVC) B = Backward congestion (from destination SVC) When an information status signal is not present, the unit displays a dash [-] in the appropriate position. |
| GAU statSvcMeanRx | 1.3.6.1.4.1.727.7.2.20.27.1.8 | Gauge | read-only | The mean bandwidth usage for data received from the destination SVC. |
| GAU statSvcMeanTx | 1.3.6.1.4.1.727.7.2.20.27.1.7 | Gauge | read-only | The mean bandwidth usage for transmissions to the destination SVC. |
| STR statSvcMode | 1.3.6.1.4.1.727.7.2.20.27.1.3 | DisplayString | read-only | SVC mode. PVCR, FP or OFF |
| CTR statSvcOctetsRx | 1.3.6.1.4.1.727.7.2.20.27.1.16 | Counter | read-only | The number of octets received |
| CTR statSvcOctetsTx | 1.3.6.1.4.1.727.7.2.20.27.1.15 | Counter | read-only | The number of octets transmitted |
| CTR statSvcOvrFrames | 1.3.6.1.4.1.727.7.2.20.27.1.18 | Counter | read-only | The number of frames received and deleted because the input queue is full. |
| CTR statSvcOvrOctets | 1.3.6.1.4.1.727.7.2.20.27.1.20 | Counter | read-only | The number of characters received and deleted because the input queue is full. |
| GAU statSvcPeakRx | 1.3.6.1.4.1.727.7.2.20.27.1.10 | Gauge | read-only | The peak bandwidth usage for data received from the destination SVC. |
| GAU statSvcPeakTx | 1.3.6.1.4.1.727.7.2.20.27.1.9 | Gauge | read-only | The peak bandwidth usage for transmissions to the destination SVC. |
| STR statSvcProtocol | 1.3.6.1.4.1.727.7.2.20.27.1.2 | DisplayString | read-only | SVC protocol. |
| CTR statSvcRestart | 1.3.6.1.4.1.727.7.2.20.27.1.12 | Counter | read-only | Number of restarts on the SVC. This counter is incremented every time the link is down for at least 1 second. In addition, if the SVC is not restored within the LINK TIMEOUT value (a Global configuration parameter), the unit will log a LINK SVC DOWN alarm. |
| STR statSvcSpeed | 1.3.6.1.4.1.727.7.2.20.27.1.5 | DisplayString | read-only | The port speed measured by the unit. |
| STR statSvcState | 1.3.6.1.4.1.727.7.2.20.27.1.6 | DisplayString | read-only | The possible states for an SVC in PVCR mode are: OFF = SVC inactive CALL = Waiting for active signal from the network TEST = SVC in test mode DATA = SVC in operation |
| statSvcTable | 1.3.6.1.4.1.727.7.2.20.27 | not-accessible | A list of statistic entries for the SVCs. | |
| statSystem | 1.3.6.1.4.1.727.7.2.20.20 | |||
| INT statSystemAlarmNumber | 1.3.6.1.4.1.727.7.2.20.20.1 | INTEGER | read-only | The maximum number of alarms that the system records |
| OCT statSystemBia | 1.3.6.1.4.1.727.7.2.20.20.9 | OCTET STRING | read-only | Burned-in address of the system. |
| INT statSystemClearAlarms | 1.3.6.1.4.1.727.7.2.20.20.12 | INTEGER | read-write | When this variable is set to yes, all alarms are erased. |
| INT statSystemClearErrorLed | 1.3.6.1.4.1.727.7.2.20.20.13 | INTEGER | read-write | When this variable is set to YES, the error LED is cleared. |
| STR statSystemMeanCompRate | 1.3.6.1.4.1.727.7.2.20.20.2 | DisplayString | read-only | Average compression rate. |
| STR statSystemMeanDecompRate | 1.3.6.1.4.1.727.7.2.20.20.3 | DisplayString | read-only | Average decompression rate. |
| OCT statSystemNa | 1.3.6.1.4.1.727.7.2.20.20.8 | OCTET STRING | read-only | Network address that the system will use to send data on the LAN. |
| STR statSystemPeakCompRate | 1.3.6.1.4.1.727.7.2.20.20.4 | DisplayString | read-only | Maximum compression rate. |
| STR statSystemPeakDecompRate | 1.3.6.1.4.1.727.7.2.20.20.5 | DisplayString | read-only | Maximum decompression rate. |
| INT statSystemResetCounters | 1.3.6.1.4.1.727.7.2.20.20.11 | INTEGER | read-write | When this variable is set to yes, all statistics counters are reset to 0 value. |
| GAU statSystemSa | 1.3.6.1.4.1.727.7.2.20.20.6 | Gauge | read-only | The number of PUs currently active and running. |
| GAU statSystemSp | 1.3.6.1.4.1.727.7.2.20.20.7 | Gauge | read-only | The number of PUs currently trying to get connected. |
| OCT statSystemTr_Nan | 1.3.6.1.4.1.727.7.2.20.20.10 | OCTET STRING | read-only | The address of the nearest active upstream neighbor on the Token-Ring. |
| INT statTimeClientRetransmissions | 1.3.6.1.4.1.727.7.2.20.23.7 | INTEGER | read-only | Number of client retransmission's. |
| INT statTimeClientSyncFailures | 1.3.6.1.4.1.727.7.2.20.23.8 | INTEGER | read-only | Number of client sync failures. |
| INT statTimeInvalidLocalIpAddress | 1.3.6.1.4.1.727.7.2.20.23.9 | INTEGER | read-only | Number of invalid local IP addresses. |
| INT statTimeInvalidPortNumbers | 1.3.6.1.4.1.727.7.2.20.23.10 | INTEGER | read-only | Number of frames with invalid port numbers. |
| INT statTimeNbFrameReceived | 1.3.6.1.4.1.727.7.2.20.23.1 | INTEGER | read-only | Number of frames received. |
| INT statTimeNbFrameSent | 1.3.6.1.4.1.727.7.2.20.23.2 | INTEGER | read-only | Number of frames sent. |
| INT statTimeNbReplyReceived | 1.3.6.1.4.1.727.7.2.20.23.6 | INTEGER | read-only | Number of replies received by time client. |
| INT statTimeNbReplySent | 1.3.6.1.4.1.727.7.2.20.23.4 | INTEGER | read-only | Number of replies sent by time server. |
| INT statTimeNbRequestReceived | 1.3.6.1.4.1.727.7.2.20.23.3 | INTEGER | read-only | Number of requests received by time server. |
| INT statTimeNbRequestSent | 1.3.6.1.4.1.727.7.2.20.23.5 | INTEGER | read-only | Number of requests sent by time client. |
| statTimep | 1.3.6.1.4.1.727.7.2.20.23 | |||
| INT statTxAcknowledgeExpiry | 1.3.6.1.4.1.727.7.2.20.25.4 | INTEGER | read-only | Number of Tx frame acks delayed waiting for Tack. |
| INT statTxBytes | 1.3.6.1.4.1.727.7.2.20.24.9 | INTEGER | read-only | Number of transmitted bytes. |
| INT statTxCallProceedingMessages | 1.3.6.1.4.1.727.7.2.20.26.3 | INTEGER | read-only | Number of transmitted call proceeding messages. |
| INT statTxConnectMessages | 1.3.6.1.4.1.727.7.2.20.26.5 | INTEGER | read-only | Number of Tx connect messages. |
| INT statTxDisconnectMessages | 1.3.6.1.4.1.727.7.2.20.26.11 | INTEGER | read-only | Number of transmitted disconnect messages. |
| INT statTxframes | 1.3.6.1.4.1.727.7.2.20.24.7 | INTEGER | read-only | Number of transmitted frames. |
| INT statTxIframeQdiscards | 1.3.6.1.4.1.727.7.2.20.24.5 | INTEGER | read-only | Number of Iframe Q discards. |
| INT statTxReleaseCompleteMessages | 1.3.6.1.4.1.727.7.2.20.26.9 | INTEGER | read-only | Number of transmitted release complete messages. |
| INT statTxReleaseMessages | 1.3.6.1.4.1.727.7.2.20.26.7 | INTEGER | read-only | Number of transmitted release messages. |
| INT statTxRetransmissions | 1.3.6.1.4.1.727.7.2.20.24.1 | INTEGER | read-only | Number of retransmissions invoked. |
| INT statTxSetupMessages | 1.3.6.1.4.1.727.7.2.20.26.1 | INTEGER | read-only | Number of transmitted setup messages. |
| INT statTxStatusEnquiryMessages | 1.3.6.1.4.1.727.7.2.20.26.15 | INTEGER | read-only | Number of transmitted status enquiry messages. |
| INT statTxStatusMessages | 1.3.6.1.4.1.727.7.2.20.26.13 | INTEGER | read-only | Number of transmitted status messages. |
| INT sysAcceptLoop | 1.3.6.1.4.1.727.7.2.1.8 | INTEGER | read-write | Control of loopback on the WAN links. This parameter determines whether loopback on any link is accepted (YES) or not accepted (NO). The unit software detects the presence of a loopback condition on any WAN link. Setting ACCEPT LOOP to NO prevents the unit from using a link that has been placed in loopback mode either temporarily or accidentally. |
| INT sysAutoSaveDelay | 1.3.6.1.4.1.727.7.2.1.46 | INTEGER | read-write | Number of seconds left after a modification and before saving in flash (0 : no auto save) |
| INT sysBackplaneRipVersion | 1.3.6.1.4.1.727.7.2.1.56 | INTEGER | read-write | When this parameter is set to V1, the RIP routing is done according to the RIP V1 standard. With RIP V2, broadcast or multicast can be used. With RIP V2 MULTICAST, only RIP V2 compliant devices will receive RIP frames. |
| STR sysClock | 1.3.6.1.4.1.727.7.2.1.6 | DisplayString | read-write | The current time. |
| STR sysContact | 1.3.6.1.4.1.727.7.2.1.2 | DisplayString | read-write | The textual identification of the contact person for this managed node, together with information on how to contact this person. |
| INT sysCountry | 1.3.6.1.4.1.727.7.2.1.38 | INTEGER | read-write | This parameter determines the type of ring, dial tone, ringback tone and busy tone that will be generated by the NetVoice card. To ensure that these signals are generated according to local standards, set this parameter to the country where the NetVoice is located. |
| STR sysDate | 1.3.6.1.4.1.727.7.2.1.5 | DisplayString | read-write | The current date. |
| INT sysDay | 1.3.6.1.4.1.727.7.2.1.7 | INTEGER | read-write | The current day. |
| IP sysDefaultGateway | 1.3.6.1.4.1.727.7.2.1.13 | IpAddress | read-write | This is the gateways IP address to use when a destination is unknown. At this time, well transmit all frame with unknown destination to this gateway. |
| IP sysDefaultIpAddr | 1.3.6.1.4.1.727.7.2.1.11 | IpAddress | read-write | Default IP address for the unit. This address is used for PVCR ports and PVCs that do not have a configures IP address (set with the IP LOCAL ADDR parameter for the port or PVC). It is a 4-byte value in dotted decimal representation with a maximum value of 255 for each byte. When set to 000.000.000.000, no default IP address is defined on the unit. |
| IP sysDefaultIpMask | 1.3.6.1.4.1.727.7.2.1.12 | IpAddress | read-write | Default IP subnet mask associated with the default IP address. It is configured like the default IP address: a 4-byte value in dotted decimal representation, with a maximum value of 255 for each byte. The default IP mask identifies which bits of the IP address correspond to the physical network, and which bits correspond to host identifiers. |
| STR sysDesc | 1.3.6.1.4.1.727.7.2.1.1 | DisplayString | read-only | This variable contains a printable octet string which contains the full name and version of the product. |
| INT sysDialTimer | 1.3.6.1.4.1.727.7.2.1.37 | INTEGER | read-write | This parameter specifies the amount of time the system should wait for a response to a Call Connect or Call Clear requests. |
| INT sysDLCI | 1.3.6.1.4.1.727.7.2.1.34 | INTEGER | read-write | The local DLCI address used as Srce field in the connection request to an FP |
| INT sysExtendedDigitsLength | 1.3.6.1.4.1.727.7.2.1.36 | INTEGER | read-write | This parameter sets the number of digits that must be entered into the telephone set when the Extension Number Source of a Voice Mapping Table entry is set to User. |
| INT sysExtensionNumLength | 1.3.6.1.4.1.727.7.2.1.35 | INTEGER | read-write | The number of digits that must be used to define a port Extension Number, or a Destination Extension Number in the Voice Mapping Table for this Netperformer. |
| INT sysHuntForwardingADLCI | 1.3.6.1.4.1.727.7.2.1.52 | INTEGER | read-write | Hunt forwarding group A DLCI address. DLCI address where a busy call for hunt group A will be forwarded on an FP PVC |
| STR sysHuntForwardingASvcAddress | 1.3.6.1.4.1.727.7.2.1.54 | DisplayString | read-write | Hunt forwarding group A SVC address. SVC address where a busy call for hunt group A will be forwarded on an FP SVC. NOTE: sysHuntForwardingAUnit must be empty otherwise this parameter is ignored |
| STR sysHuntForwardingAUnit | 1.3.6.1.4.1.727.7.2.1.50 | DisplayString | read-write | Hunt forwarding group A Unit name. Unit name where a busy call for hunt group A will be forwarded to |
| INT sysHuntForwardingBDLCI | 1.3.6.1.4.1.727.7.2.1.53 | INTEGER | read-write | Hunt forwarding group B DLCI address. DLCI address where a busy call for hunt group B will be forwarded on an FP PVC |
| STR sysHuntForwardingBSvcAddress | 1.3.6.1.4.1.727.7.2.1.55 | DisplayString | read-write | Hunt forwarding group A SVC address. SVC address where a busy call for hunt group A will be forwarded on an FP SVC. NOTE: sysHuntForwardingBUnit must be empty otherwise this parameter is ignored |
| STR sysHuntForwardingBUnit | 1.3.6.1.4.1.727.7.2.1.51 | DisplayString | read-write | Hunt forwarding group B Unit name. Unit name where a busy call for hunt group B will be forwarded to |
| INT sysJitterBuf | 1.3.6.1.4.1.727.7.2.1.39 | INTEGER | read-write | The amount of jitter delay, in milliseconds, that the unit voice uses to compensate for the variable arrival time of packets. |
| INT sysLinkTimeout_s | 1.3.6.1.4.1.727.7.2.1.9 | INTEGER | read-write | The delay, in seconds, before a WAN link is declared down during a link failure. This timeout can be used to prevent the accumulation of LINK DOWN alarms in the unit when brief link failures occur. |
| STR sysLocation | 1.3.6.1.4.1.727.7.2.1.4 | DisplayString | read-write | The physical location of this node (e.g., `telephone closet, 3rd floor'). |
| STR sysName | 1.3.6.1.4.1.727.7.2.1.3 | DisplayString | read-write | An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name. |
| sysPosEntry | 1.3.6.1.4.1.727.7.2.1.32.1 | not-accessible | This entry contains the principal configurable parameters related to CS racks and positions | |
| INT sysPosId | 1.3.6.1.4.1.727.7.2.1.32.1.2 | INTEGER | read-only | ID of the CS-Rack's position that the board at sysPosIndex is plugged in |
| IP sysPosIpAddr | 1.3.6.1.4.1.727.7.2.1.32.1.5 | IpAddress | read-only | the (Default) IP address for the unit. It means that, by managing this table in one position, we can see and alter the other position's IP addresses |
| INT sysPosNr | 1.3.6.1.4.1.727.7.2.1.31 | INTEGER | read-only | The number of positions in the Rack this board belongs to (Always 8, hardware characteristic) |
| OID sysPosProduct | 1.3.6.1.4.1.727.7.2.1.32.1.3 | OBJECT IDENTIFIER | read-only | The Product descriptor of the board at sysPosIndex in the OID form e.g.: {presticom netperformer7 product product-id} |
| INT sysPosRackId | 1.3.6.1.4.1.727.7.2.1.32.1.4 | INTEGER | read-only | ID of the CS-Rackds as it is configured in the board indexed by sysPosIndex. On a correctly configured installation, all positions in one rack must bear the same rackId |
| sysPosTable | 1.3.6.1.4.1.727.7.2.1.32 | not-accessible | This table represents the entire rack this board belongs to. The number of entries is sysPosNr | |
| INT sysPsAndFansMonitoring | 1.3.6.1.4.1.727.7.2.1.16 | INTEGER | read-write | The monitoring functionality of the Power Supplies and Fans. |
| INT sysPsMonitoring | 1.3.6.1.4.1.727.7.2.1.47 | INTEGER | read-write | The monitoring functionality of the Power Supplies and Fans. |
| INT sysRackId | 1.3.6.1.4.1.727.7.2.1.15 | INTEGER | read-write | ID of the CS-Rack this board is plugged in |
| INT sysRacksNr | 1.3.6.1.4.1.727.7.2.1.33 | INTEGER | read-only | The total number of populated Racks in the system (1 to 4 racks) |
| INT sysRingFreq | 1.3.6.1.4.1.727.7.2.1.40 | INTEGER | read-write | the frequency in hertz, at which a ring is generated on locally attached equipment |
| INT sysRingVolt | 1.3.6.1.4.1.727.7.2.1.41 | INTEGER | read-write | the voltage, in volts rms, at which a ring is generated on locally attached equipment. |
| IP sysSnmpTrapIpAddr1 | 1.3.6.1.4.1.727.7.2.1.17 | IpAddress | read-write | Specific IP address to sent SNMP trap. |
| IP sysSnmpTrapIpAddr2 | 1.3.6.1.4.1.727.7.2.1.18 | IpAddress | read-write | Specific IP address to sent SNMP trap. |
| IP sysSnmpTrapIpAddr3 | 1.3.6.1.4.1.727.7.2.1.19 | IpAddress | read-write | Specific IP address to sent SNMP trap. |
| IP sysSnmpTrapIpAddr4 | 1.3.6.1.4.1.727.7.2.1.20 | IpAddress | read-write | Specific IP address to sent SNMP trap. |
| INT sysSpeedDialNumLength | 1.3.6.1.4.1.727.7.2.1.45 | INTEGER | read-write | Number of digit of the MAP numbers |
| system | 1.3.6.1.4.1.727.7.2.1 | |||
| INT sysThisPosId | 1.3.6.1.4.1.727.7.2.1.30 | INTEGER | read-only | ID of this board's position |
| INT sysTransitDelay_s | 1.3.6.1.4.1.727.7.2.1.10 | INTEGER | read-write | The maximum delay, in seconds, allowed to elapse between the reception and transmission of a forwarded frame by a bridge. a timer is started if a link report that it is too busy to transmit a frame. Frame that are nor processed within the transit delay are discarded. |
| INT sysTrapRackandPos | 1.3.6.1.4.1.727.7.2.1.57 | INTEGER | read-only | Rack ID X 10 + Position ID. |
| INT sysUnitRoutingVersion | 1.3.6.1.4.1.727.7.2.1.21 | INTEGER | read-write | As of software release 6.7.0, the netperformer7 product line has an improved routing version for destinations reached via ports and PVCs configured with the PVCR protocol. This new routing version is called Version 2, and the previous routing version is referred to as Version 1. The most recent release of the netperformer7 (software release 6.7.0) can be configured to run either routing version. The routing version used for a particular unit is determined by the Unit Routing Version parameter. Unit Routing Version: The routing version to be used on this unit. Select 1 if any netperformer7 units in the network are running Unit Routing Version 1 (the version used in all software releases earlier than 6.7.0). Select 2 if all netperformer7 units in the network are running Unit Routing Version 2 (software release 6.7.0). |
| INT sysVoiceClass | 1.3.6.1.4.1.727.7.2.1.49 | INTEGER | read-write | Associate the voice traffic to a class priority. Effective only if sysVoiceHighestPriority is set to no |
| INT sysVoiceClocking | 1.3.6.1.4.1.727.7.2.1.43 | INTEGER | read-write | SN-7800 and RX only... |
| INT sysVoiceEncoding | 1.3.6.1.4.1.727.7.2.1.42 | INTEGER | read-write | SN-7800 and RX only... |
| INT sysVoiceHighestPriority | 1.3.6.1.4.1.727.7.2.1.48 | INTEGER | read-write | When set to yes, the voice traffic has unconditionnaly the highest possible priority. When set to no, the voice priority is specified by sysVoiceClass. |
| INT sysVoiceLog | 1.3.6.1.4.1.727.7.2.1.44 | INTEGER | read-write | Enable logs (accounting) on voice/fax ports |
| timep | 1.3.6.1.4.1.727.7.2.35 | |||
| INT timepClientProtocol | 1.3.6.1.4.1.727.7.2.35.5 | INTEGER | read-write | Protocols used by the time client. |
| INT timepClientUdpRetransmissions | 1.3.6.1.4.1.727.7.2.35.9 | INTEGER | read-write | Time client UDP retransmissions. |
| INT timepClientUdpTimeout | 1.3.6.1.4.1.727.7.2.35.8 | INTEGER | read-write | Time client UDP timeout (in seconds). |
| INT timepClientUpdateInterval | 1.3.6.1.4.1.727.7.2.35.7 | INTEGER | read-write | Time client update interval (in minutes). |
| INT timepDaylightSaving | 1.3.6.1.4.1.727.7.2.35.3 | INTEGER | read-write | Enable daylight saving time (one hour). |
| INT timepGetServerTimeNow | 1.3.6.1.4.1.727.7.2.35.10 | INTEGER | read-write | Get time from time server. Do not wait for update timer to expire. Time client must be enabled and time server must be on line. If everything is up, it will take approximately 60 seconds before the time is updated |
| IP timepServerIpAddress | 1.3.6.1.4.1.727.7.2.35.6 | IpAddress | read-write | IP address of time client server. |
| INT timepServerProtocol | 1.3.6.1.4.1.727.7.2.35.4 | INTEGER | read-write | Protocols supported by the time server. |
| INT timepTimeZone | 1.3.6.1.4.1.727.7.2.35.2 | INTEGER | read-write | Time offset from GMT (in minutes). |
| INT timepTimeZoneSign | 1.3.6.1.4.1.727.7.2.35.1 | INTEGER | read-write | Time zone offset sign. YES means negative |
| tMS380C26 | 1.3.6.1.4.1.727.7.50.1 | |||
| tMS380C30 | 1.3.6.1.4.1.727.7.50.3 | |||
| ver6X_Device | 1.3.6.1.4.1.727.7.1.2 |
RFC description
Monitors system status, interfaces, and statistics for ACT Presticom BCX-5000/6000/8000 series devices.
Start monitoring Legacy voice/data access equipment, enterprise OID 727 (Presticom) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.