All MIBs › RADWIN-MIB-WINLINK1000
Category: DSL and Broadband, Wireless and WLAN
Description: Management MIB for RADWIN WinLink1000 point-to-point broadband wireless systems, providing configuration, link status, performance monitoring, and diagnostics.
IPNetwork Monitor uses several OIDs from this MIB in network discovery and polling the applicable devices. Start monitoring RADWIN-MIB-WINLINK1000 with a free 30-day trial of IPNetwork Monitor.
What Is RADWIN-MIB-WINLINK1000?
RADWIN-MIB-WINLINK1000 is a vendor-specific MIB from RADWIN for managing the WinLink1000 family of point-to-point broadband wireless transmission systems used in fixed wireless backhaul links. It exposes configuration, radio link status, RF performance metrics, and diagnostic objects specific to the wireless link hardware. It is explicitly used for monitoring hardware status such as link signal quality, modulation state, and radio unit health, alongside software configuration of the wireless link parameters. As a self-contained vendor MIB for a specific product line, it has limited dependency on external standards MIBs beyond basic SNMP framework conventions. It is typically deployed in point-to-point wireless backhaul deployments connecting remote sites, towers, or base stations. Engineers can download the RADWIN-MIB-WINLINK1000 file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in RADWIN-MIB-WINLINK1000. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- RADWIN WinLink1000 point-to-point wireless transmission units
Monitoring Examples
An administrator would poll radio link status and RF performance objects (signal strength, modulation mode, link uptime) to verify a WinLink1000 point-to-point link is operating at expected throughput and quality. A drop in modulation level or signal quality metrics would reveal weather-related fade or antenna alignment issues affecting the wireless backhaul. Diagnostic counters would be checked to confirm the radio hardware itself is functioning normally versus a configuration mismatch between link endpoints.
What Can Be Monitored
- radio link status
- signal quality/RF performance
- modulation mode
- link configuration parameters
- diagnostic/fault indicators
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| TimeTicks | |
| enterprises |
From RFC1213-MIB
| DisplayString | |
| ifIndex |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| radwin | 1.3.6.1.4.1.4458 | |||
| radwinProducts | 1.3.6.1.4.1.4458.20 | |||
| winlink1000Family | 1.3.6.1.4.1.4458.20.2 | |||
| odu | 1.3.6.1.4.1.4458.20.2.1 | |||
| oduIntegratedAntenna | 1.3.6.1.4.1.4458.20.2.1.1 | |||
| oduExternalAntenna | 1.3.6.1.4.1.4458.20.2.1.2 | |||
| radwin2000Family | 1.3.6.1.4.1.4458.20.3 | |||
| odu2000 | 1.3.6.1.4.1.4458.20.3.1 | |||
| odu2KIntegratedAntenna | 1.3.6.1.4.1.4458.20.3.1.1 | |||
| odu2KExternalAntenna | 1.3.6.1.4.1.4458.20.3.1.2 | |||
| gpsSynchronizerFamily | 1.3.6.1.4.1.4458.20.4 | |||
| oduGSU | 1.3.6.1.4.1.4458.20.4.1 | |||
| oduGSUExternalAntenna | 1.3.6.1.4.1.4458.20.4.1.2 | |||
| hssSyncUnits | 1.3.6.1.4.1.4458.20.4.2 | |||
| hssISU | 1.3.6.1.4.1.4458.20.4.2.1 | |||
| hssGSU | 1.3.6.1.4.1.4458.20.4.2.2 | |||
| radwin5000HBSFamily | 1.3.6.1.4.1.4458.20.5 | |||
| oduHBS | 1.3.6.1.4.1.4458.20.5.1 | |||
| oduHBSIntegratedAntenna | 1.3.6.1.4.1.4458.20.5.1.1 | |||
| oduHBSExternalAntenna | 1.3.6.1.4.1.4458.20.5.1.2 | |||
| radwin5000HSUFamily | 1.3.6.1.4.1.4458.20.6 | |||
| oduHSU | 1.3.6.1.4.1.4458.20.6.1 | |||
| oduHSUIntegratedAntenna | 1.3.6.1.4.1.4458.20.6.1.1 | |||
| oduHSUExternalAntenna | 1.3.6.1.4.1.4458.20.6.1.2 | |||
| radwin6000Family | 1.3.6.1.4.1.4458.20.10 | |||
| odu6000 | 1.3.6.1.4.1.4458.20.10.1 | |||
| odu6K | 1.3.6.1.4.1.4458.20.10.1.1 | |||
| gateway6000 | 1.3.6.1.4.1.4458.20.10.2 | |||
| gateway6K | 1.3.6.1.4.1.4458.20.10.2.1 | |||
| radwinWiFiAPFamily | 1.3.6.1.4.1.4458.20.20 | |||
| odu600 | 1.3.6.1.4.1.4458.20.20.1 | |||
| oduWiFiAP | 1.3.6.1.4.1.4458.20.20.1.1 | |||
| winlink1000 | 1.3.6.1.4.1.4458.1000 | |||
| NTF externalAlarmInPort1Alarm | 1.3.6.1.4.1.4458.1000.0.105 | The trap is sent every time an alarm occurs in the External Alarm Input of port #1. Contains a single parameter, which is its description: 1 - Description: External Alarm 1 - - Alarm. | ||
| NTF externalAlarmInPort2Alarm | 1.3.6.1.4.1.4458.1000.0.106 | The trap is sent every time an alarm occurs in the External Alarm Input of port #2. Contains a single parameter, which is its description: 1 - Description: External Alarm 2 - - Alarm. | ||
| NTF bitFailedAlarm | 1.3.6.1.4.1.4458.1000.0.107 | The trap is sent if there is no way to recover from the situation. Contains two parameters: 1 - Description: ODU power up built in test failed. Error code is: %n 2 - %n number | ||
| NTF wrongConfigurationLoadedAlarm | 1.3.6.1.4.1.4458.1000.0.108 | The trap is sent if there is a way to recover from the situation. Contains two parameters: 1 - Description: Wrong configuration loaded. Error code is: %n 2 - %n number | ||
| NTF lanPort1DisconnectedAlarm | 1.3.6.1.4.1.4458.1000.0.109 | Indicates the LAN port 1 status changed to disconnected. Contains a single parameter, which is its description: 1 - Description: LAN port 1 status changed to disconnected. | ||
| NTF lanPort2DisconnectedAlarm | 1.3.6.1.4.1.4458.1000.0.110 | Indicates the LAN port 2 status changed to disconnected. Contains a single parameter, which is its description: 1 - Description: LAN port 2 status changed to disconnected. | ||
| NTF mngPortDisconnectedAlarm | 1.3.6.1.4.1.4458.1000.0.111 | Indicates the LAN1 port status changed to disconnected. Contains a single parameter, which is its description: 1 - Description: LAN1 port status changed to disconnected. | ||
| NTF externalAlarmInPort3Alarm | 1.3.6.1.4.1.4458.1000.0.112 | The trap is sent every time an alarm occurs in the External Alarm Input of port #3. Contains a single parameter, which is its description: 1 - Description: External Alarm 3 - - Alarm. | ||
| NTF externalAlarmInPort4Alarm | 1.3.6.1.4.1.4458.1000.0.113 | The trap is sent every time an alarm occurs in the External Alarm Input of port #4. Contains a single parameter, which is its description: 1 - Description: External Alarm 4 - - Alarm. | ||
| NTF swVersionsMismatchFullCompatibilityAlarm | 1.3.6.1.4.1.4458.1000.0.114 | The trap is sent if SW versions mismatch with full link functionality. Contains a single parameter, which is its description: 1 - Description: Software versions mismatch - full link functionality | ||
| NTF swVersionsMismatchRestrictedCompatibilityAlarm | 1.3.6.1.4.1.4458.1000.0.115 | The trap is sent if SW versions mismatch with restricted link functionality. Contains a single parameter, which is its description: 1 - Description: Software versions mismatch - restricted link functionality | ||
| NTF swVersionsMismatchSoftwareUpgradeRequired | 1.3.6.1.4.1.4458.1000.0.116 | The trap is sent if SW versions mismatch and SW upgrade is required. Contains a single parameter, which is its description: 1 - Description: Software versions mismatch - Software upgrade required | ||
| NTF swVersionsIncompatible | 1.3.6.1.4.1.4458.1000.0.117 | The trap is sent if SW versions are incompatible. Contains a single parameter, which is its description: 1 - Description: SW Versions incompatible | ||
| NTF hssMultipleSourcesDetectedAlarm | 1.3.6.1.4.1.4458.1000.0.118 | Indicates that multiple sync pulse sources were detected. Contains a single parameter, which is its description: 1 - Description: HSS multiple sync sources were detected. | ||
| NTF hssSyncToProperSourceStoppedAlarm | 1.3.6.1.4.1.4458.1000.0.119 | Indicates that synchronization to a proper sync pulse source was stopped. Contains a single parameter, which is its description: 1 - Description: HSS sync pulse - Down. The reason is: %s. %s - Is the reason for the sync down. | ||
| NTF hssSyncPulseDetectedAlarm | 1.3.6.1.4.1.4458.1000.0.120 | Indicates that HSS additional sync pulse was detected. Contains a single parameter, which is its description: 1 - Description: HSS additional sync pulse was detected. | ||
| NTF tdmBackupAlarm | 1.3.6.1.4.1.4458.1000.0.121 | Indicates that the TDM backup link was activated. Contains a single parameter, which is its description: 1 - Description: TDM backup alarm - backup link was activated. | ||
| NTF linkLockUnauthorizedRemoteODU | 1.3.6.1.4.1.4458.1000.0.122 | Indicates that the remote ODU is unauthorized. Contains a single parameter, which is its description: 1 - Description: Unauthorized remote ODU connection rejected. | ||
| NTF linkLockUnauthorizedODU | 1.3.6.1.4.1.4458.1000.0.123 | Indicates that the ODU is unauthorized. Contains a single parameter, which is its description: 1 - Description: Unauthorized ODU connection rejected. | ||
| NTF hotStandbyAlarm | 1.3.6.1.4.1.4458.1000.0.124 | Indicates that the hot standby secondary link was activated. Contains a single parameter, which is its description: 1 - Description: Secondary Link Is Active. | ||
| NTF sfpInsertion | 1.3.6.1.4.1.4458.1000.0.126 | Indicates that a device was inserted to SFP Port | ||
| NTF sfpPort1DisconnectedAlarm | 1.3.6.1.4.1.4458.1000.0.127 | Indicates the SFP port 1 status changed to disconnected. Contains a single parameter which is its description: 1 - Description: SFP port 1 status changed to disconnected. | ||
| NTF ringRplStateActiveAlarm | 1.3.6.1.4.1.4458.1000.0.128 | RPL state changed to Active. | ||
| NTF desiredRatioCanNotBeAppliedAlarm | 1.3.6.1.4.1.4458.1000.0.129 | Indicates Desired UL/DL RAtio Can Not Be Applied. | ||
| NTF cbwMismatch | 1.3.6.1.4.1.4458.1000.0.130 | Indicates that a Channel Bandwidth mismatch was detected. Contains two parameters: 1 - Description: Channel Bandwidth Mismatch: one side is %n0 MHz and the other is %n1 MHz. %n0 is the local Channel Bandwidth value in MHz. %n1 is the remoet Channel Bandwidth value in MHz. | ||
| NTF gpsNotSynchronized | 1.3.6.1.4.1.4458.1000.0.131 | Indicates that the GPS is not synchronized with satellites. Pulses are self generated. | ||
| NTF pdTooHighDueCbwLimitations | 1.3.6.1.4.1.4458.1000.0.132 | Indicates that link cannot be established because link range is too large for channel bandwidth. | ||
| NTF hbsEncryptionAlarm | 1.3.6.1.4.1.4458.1000.0.133 | Indicates an encryption key mismatch. Contains a single parameter, which is its description, including the HSU's name | ||
| NTF hbsEhServiceClosedToHsu | 1.3.6.1.4.1.4458.1000.0.134 | Indicates an encryption key mismatch. Contains a single parameter, which is its description, including the HSU's name | ||
| NTF hbsUnsynchronizedHsuAlarm | 1.3.6.1.4.1.4458.1000.0.135 | Indicates a registered HSU lost synchronization. | ||
| NTF hbsInactiveHbsAlarm | 1.3.6.1.4.1.4458.1000.0.136 | Indicates HBS is InActive. | ||
| NTF incompatibleHsu | 1.3.6.1.4.1.4458.1000.0.137 | Indicates that the HSU is not compatible to HBS. Contains a single parameter, which is its description: 1 - Description: Incompatible ODUs. | ||
| NTF hsuUnsupportedBeacon | 1.3.6.1.4.1.4458.1000.0.138 | Indicates an unsupported beacon has arrived at HSU | ||
| NTF lanPortDisconnectedAlarm | 1.3.6.1.4.1.4458.1000.0.139 | Indicates the LAN port status changed to disconnected. Contains a single parameter, which is its description: 1 - Description: LAN port status changed to disconnected. | ||
| NTF poePortDisconnectedAlarm | 1.3.6.1.4.1.4458.1000.0.140 | Indicates the LAN2 port status changed to disconnected. Contains a single parameter, which is its description: 1 - Description: LAN2 port status changed to disconnected. | ||
| NTF poePowerConsumptionAlarm | 1.3.6.1.4.1.4458.1000.0.141 | Indicates the POE Power Consumption is above allowed maximum. Contains a single parameter, which is its description: 1 - Description: POE consumption above allowed maximum. port closed. | ||
| NTF hobupFaultyStateAlarm | 1.3.6.1.4.1.4458.1000.0.149 | This Alarm will indicate that the Hot Backup module is in faulty state. 1 - Description: Hot Backup fault detected: %s unit. %s - Primary Or Secondary Unit | ||
| NTF gpsOverCurrentAlarm | 1.3.6.1.4.1.4458.1000.0.150 | Indicates the GPS Antenna current consumption is above allowed maximum. Contains a single parameter, which is its description: 1 - Description: GPS Antenna current consumption above allowed maximum. GPS closed. | ||
| NTF gpsCommunicationFailiureAlarm | 1.3.6.1.4.1.4458.1000.0.151 | Indicates the GPS data isn't received. Contains a single parameter, which is its description: 1 - Description: GPS Communication failiure. | ||
| NTF temperatureThresholdAlarm | 1.3.6.1.4.1.4458.1000.0.152 | Indicates the board temperature is above allowed maximum. Contains a single parameter, which is its description: 1 - Description: GPS Antenna current consumption above allowed maximum. GPS closed. | ||
| NTF localRouterDiscoveryStatus | 1.3.6.1.4.1.4458.1000.0.153 | This Alarm will indicate that we have no connection with local train router. 1 - Description: MacLearningUpdate detected disconnection with local train router %s %s - local train IP | ||
| NTF trackRouterDiscoveryStatus | 1.3.6.1.4.1.4458.1000.0.154 | This Alarm will indicate that we have no connection with Track side router. 1 - Description: MacLearningUpdate detected disconnection with Track side router %s %s - Default gateway IP | ||
| NTF lastUserSnmpAccessOverHourAgo | 1.3.6.1.4.1.4458.1000.0.155 | This trap will indicate that the last access of the accessing user was more than an hour ago. 1 - Description: User %s performed SNMP access after more than an hour. %s - user name | ||
| NTF btsTargetUnreachable | 1.3.6.1.4.1.4458.1000.0.156 | This Alarm will indicate that we have no connection with Bts desired target. 1 - Description: TNC detected disconnection with the BTS target %s %s - Default gateway IP | ||
| NTF tdmServiceClear | 1.3.6.1.4.1.4458.1000.0.200 | Indicates that TDM Service fault is cleared. Contains a single parameter, which is its description: 1 - Description: TDM Service - Normal. | ||
| NTF ethServiceOpened | 1.3.6.1.4.1.4458.1000.0.201 | Indicates that Ethernet Service has been opened. Contains a single parameter, which is its description: 1 - Description: Ethernet Service has been opened. | ||
| NTF encryptionClear | 1.3.6.1.4.1.4458.1000.0.203 | Indicates that encryption is OK. Contains a single parameter, which is its description: 1 - Description: Encryption Status - Normal. | ||
| NTF changeLinkPasswordClear | 1.3.6.1.4.1.4458.1000.0.204 | Indicates that the Link Password was changed successfully. Contains a single parameter, which is its description: 1 - Description: Link Password has been changed at/on: %s. %s - Is the Local Site name or Remote Site name or both sides of the Link. | ||
| NTF externalAlarmInPort1Clear | 1.3.6.1.4.1.4458.1000.0.205 | This Trap is sent every time an External Alarm Input fault of port # 1 is cleared. Contains a single parameter, which is its description: 1 - Description: External Alarm 1 - - Alarm Cleared. | ||
| NTF externalAlarmInPort2Clear | 1.3.6.1.4.1.4458.1000.0.206 | This Trap is sent every time an External Alarm Input fault of port # 2 is cleared. Contains a single parameter, which is its description: 1 - Description: External Alarm 2 - - Alarm Cleared. | ||
| NTF lanPort1Clear | 1.3.6.1.4.1.4458.1000.0.209 | Indicates the LAN port 1 status changed to connected. Contains two parameters: 1 - Description: LAN port 1 status changed to connected - %s 2 - %s Is the Eth. mode (speed & duplex) | ||
| NTF lanPort2Clear | 1.3.6.1.4.1.4458.1000.0.210 | Indicates the LAN port 2 status changed to connected. Contains two parameters: 1 - Description: LAN port 2 status changed to connected - %s. 2 - %s Is the Eth. mode (speed & duplex). | ||
| NTF mngPortClear | 1.3.6.1.4.1.4458.1000.0.211 | Indicates the LAN1 port status changed to connected. Contains two parameters: 1 - Description: LAN1 port status changed to connected - %s 2 - %s Is the Eth. mode (speed & duplex) | ||
| NTF externalAlarmInPort3Clear | 1.3.6.1.4.1.4458.1000.0.212 | This Trap is sent every time an External Alarm Input fault of port # 3 is cleared. Contains a single parameter, which is its description: 1 - Description: External Alarm 3 - - Alarm Cleared. | ||
| NTF externalAlarmInPort4Clear | 1.3.6.1.4.1.4458.1000.0.213 | This Trap is sent every time an External Alarm Input fault of port # 4 is cleared. Contains a single parameter, which is its description: 1 - Description: External Alarm 4 - - Alarm Cleared. | ||
| NTF swVersionsMatchFullCompatibilityClear | 1.3.6.1.4.1.4458.1000.0.214 | The trap is sent if SW versions match. Contains a single parameter, which is its description: 1 - Description: Software Versions compatible | ||
| NTF swVersionsMatchRestrictedCompatibilityClear | 1.3.6.1.4.1.4458.1000.0.215 | The trap is sent if SW versions match and link functionality is not restricted. Contains a single parameter, which is its description: 1 - Description: Software Versions compatible | ||
| NTF swVersionsMatchSoftwareUpgradeRequiredClear | 1.3.6.1.4.1.4458.1000.0.216 | The trap is sent if SW versions match and SW upgrade is successful. Contains a single parameter, which is its description: 1 - Description: Software Versions compatible | ||
| NTF swVersionsCompatibleClear | 1.3.6.1.4.1.4458.1000.0.217 | The trap is sent if SW versions compatible Contains a single parameter, which is its description: 1 - Description: Software Versions compatible | ||
| NTF hssMultipleSourcesDisappearedClear | 1.3.6.1.4.1.4458.1000.0.218 | Indicates that multiple sync pulse sources disappeared. Contains a single parameter, which is its description: 1 - Description: HSS multiple sync pulse sources disappeared. | ||
| NTF hssSyncToProperSourceAchievedClear | 1.3.6.1.4.1.4458.1000.0.219 | Indicates that synchronization to a proper Sync source was achieved. Contains a single parameter, which is its description: 1 - Description: HSS sync pulse - Up. | ||
| NTF hssSyncPulseDisappearedClear | 1.3.6.1.4.1.4458.1000.0.220 | Indicates that HSS additional sync pulse disappeared. Contains a single parameter, which is its description: 1 - Description: HSS additional sync pulse was disappeared. | ||
| NTF tdmBackupClear | 1.3.6.1.4.1.4458.1000.0.221 | Indicates that the TDM main link was activated. Contains a single parameter, which is its description: 1 - Description: TDM main link was activated. | ||
| NTF linkLockAuthorizedRemoteODU | 1.3.6.1.4.1.4458.1000.0.222 | Indicates that the remote ODU is authorized. Contains a single parameter, which is its description: 1 - Description: Authorized remote ODU connection accepted. | ||
| NTF linkLockAuthorizedODU | 1.3.6.1.4.1.4458.1000.0.223 | Indicates that the ODU is authorized. Contains a single parameter, which is its description: 1 - Description: Authorized ODU connection permitted. | ||
| NTF linkAuthenticationDisabled | 1.3.6.1.4.1.4458.1000.0.224 | Indicates that the Link Lock is disabled. Contains a single parameter, which is its description: 1 - Description: Link Authentication has been disabled. | ||
| NTF hotStandbyClear | 1.3.6.1.4.1.4458.1000.0.225 | Indicates that the Primary Link Was Activated. Contains a single parameter, which is its description: 1 - Description: Primary Link Is Active. | ||
| NTF sfpExtraction | 1.3.6.1.4.1.4458.1000.0.226 | Indicates that a device was extracted from SFP Port | ||
| NTF sfpPort1Clear | 1.3.6.1.4.1.4458.1000.0.227 | Indicates the SFP port 1 status changed to connected. Contains two parameters: 1 - Description: SFP port 1 status changed to connected - %s 2 - %s Is the Eth. mode (speed & duplex) | ||
| NTF compatibleIdus | 1.3.6.1.4.1.4458.1000.0.228 | Indicates that the ODU has identified compatible Idus on both sides of the link. | ||
| NTF desiredRatioCanNotBeAppliedClear | 1.3.6.1.4.1.4458.1000.0.229 | Indicates Current UL/DL Ratio Is Equal To Desired Ratio. | ||
| NTF cbwMatch | 1.3.6.1.4.1.4458.1000.0.230 | Indicates that a Channel Bandwidth match was detected. Contains a single parameter, which is its description: 1 - Channel Bandwidth value in MHz. | ||
| NTF switchCbwAndChannel | 1.3.6.1.4.1.4458.1000.0.231 | Indicates that the system is switching Channel Bandwidth and channel frequency. Contains two parameters: 1 - Switching to Channel Bandwith %n0 MHz and to channel %n1 GHz. | ||
| NTF ringRplStateIdle | 1.3.6.1.4.1.4458.1000.0.232 | RPL state changed to Idle. | ||
| NTF ringEthServiceStatus | 1.3.6.1.4.1.4458.1000.0.233 | Indicates Ethernet service's state - blocked \ unblocked. Contains a single parameter: 1 - Description: Ethernet's state (blocked \ unblocked) | ||
| NTF ringFirstRpmReceived | 1.3.6.1.4.1.4458.1000.0.234 | Ring application: in non-RPL link indicates first from a specific RPL was received. Contains a single parameter: 1 - Description: RPM's VLAN ID | ||
| NTF ringEthernetSrviceUnblockedTO | 1.3.6.1.4.1.4458.1000.0.235 | Ring application: in non-RPL link Ethernet service is unblocked due to RPM timeout. | ||
| NTF gpsSynchronized | 1.3.6.1.4.1.4458.1000.0.236 | Indicates that the GPS is synchronized with satellites. | ||
| NTF hbsEncryptionClear | 1.3.6.1.4.1.4458.1000.0.237 | Indicates that encryption is OK. Contains a single parameter, which is its description, including the HSU's name | ||
| NTF hbsEhServiceOpenedToHsu | 1.3.6.1.4.1.4458.1000.0.238 | Indicates that encryption is OK. Contains a single parameter, which is its description, including the HSU's name | ||
| NTF hbsSynchronizedHsuAlarm | 1.3.6.1.4.1.4458.1000.0.239 | Indicates a registered HSU is synchronized. | ||
| NTF hbsActiveHbs | 1.3.6.1.4.1.4458.1000.0.240 | Indicates when HBS has been activated. | ||
| NTF switchCBW | 1.3.6.1.4.1.4458.1000.0.241 | Switching Channel Bandwidth. | ||
| NTF changeRatio | 1.3.6.1.4.1.4458.1000.0.242 | HBS Tx ratio has changed. | ||
| NTF lanPortClear | 1.3.6.1.4.1.4458.1000.0.243 | Indicates the LAN port status changed to connected. Contains two parameters: 1 - Description: LAN port status changed to connected - %s 2 - %s Is the Eth. mode (speed & duplex) | ||
| NTF poePortClear | 1.3.6.1.4.1.4458.1000.0.244 | Indicates the LAN2 port status changed to connected. Contains two parameters: 1 - Description: LAN2 port status changed to connected - %s 2 - %s Is the Eth. mode (speed & duplex) | ||
| NTF poePowerConsumptionClear | 1.3.6.1.4.1.4458.1000.0.245 | Indicates the POE power consumption is valid. Contains two parameters: 1 - Description: POE consumption within limits. port is opened. 2 - %s Is the Eth. mode (speed & duplex) | ||
| NTF incompatibleHbsHsu | 1.3.6.1.4.1.4458.1000.0.246 | Incompatible HBS/HSU software versions - no service. | ||
| NTF mobilityLinkOff | 1.3.6.1.4.1.4458.1000.0.247 | Mobility - Link cannot be established due to: 1 - The HBS does not support Mobility 2 - Lack of resources in the HBS for HSU level | ||
| NTF enterLocalConnection | 1.3.6.1.4.1.4458.1000.0.248 | Entering Local Connection (Broadcast) Mode. | ||
| NTF hobupActiveStateFaultyClear | 1.3.6.1.4.1.4458.1000.0.249 | this clear alarm will indicate that the Hot Backup unit is in active state. Contains a single parameter, which is its description: 1 - Description: Hot Backup %s unit activated. %s - Primary Or Secondary Unit | ||
| NTF hobupStandbyState | 1.3.6.1.4.1.4458.1000.0.250 | This info fault will indicate that the Hot backup module has entered standby/peer_detection state Contains a single parameter, which is its description: 1 - Description: Hot Backup in Standby state: %s unit. %s - Primary Or Secondary Unit | ||
| NTF gpsOverCurrentClear | 1.3.6.1.4.1.4458.1000.0.251 | Indicates the GPS Antenna current consumption is valid. | ||
| NTF temperatureThresholdClear | 1.3.6.1.4.1.4458.1000.0.252 | Indicates the board temperature is valid. | ||
| NTF localRouterDiscoverySucceed | 1.3.6.1.4.1.4458.1000.0.253 | Indicated the we succeeded to discover train router in ip %s MAC address %s %s Train IP %s Train MAC Address | ||
| NTF trackRouterDiscoverySucceed | 1.3.6.1.4.1.4458.1000.0.254 | Indicated the we succeeded to discover track router in ip %s MAC address %s %s Train IP %s Train MAC Address | ||
| NTF qosVersion2StrictMismatch | 1.3.6.1.4.1.4458.1000.0.255 | CPE doesn't support strict QOS configuration. | ||
| NTF qosVersion2TtlMismatch | 1.3.6.1.4.1.4458.1000.0.256 | CPE doesn't support TTL configuration. | ||
| NTF btsTargetIsReachable | 1.3.6.1.4.1.4458.1000.0.257 | Indicated the we succeeded to establish connection with the Bts desired target (%s) %s Target IP | ||
| NTF tcNotSupportedByHSU | 1.3.6.1.4.1.4458.1000.0.258 | CPE doesn't support TC functionality. | ||
| NTF syncEPortHOStateChange | 1.3.6.1.4.1.4458.1000.0.259 | Enter/leave HO state of SyncE port. | ||
| NTF syncEPortFailureStateChange | 1.3.6.1.4.1.4458.1000.0.260 | Enter/leave Failure state of SyncE port. | ||
| NTF btsCpeUpdateServiceFailed | 1.3.6.1.4.1.4458.1000.0.261 | Update service Failed | ||
| NTF btsCpeUpdateServiceSucceed | 1.3.6.1.4.1.4458.1000.0.262 | Update service Succeed | ||
| NTF radiusServerNoREsponse | 1.3.6.1.4.1.4458.1000.0.263 | No response from radius server | ||
| NTF noRadiusServerRespond | 1.3.6.1.4.1.4458.1000.0.264 | Alarm indicates that no Radius server is connected | ||
| NTF radiusServerRespondedSuccessfully | 1.3.6.1.4.1.4458.1000.0.265 | indicates that Radius server responded seccessfully. | ||
| NTF bsaAlignmentStarted | 1.3.6.1.4.1.4458.1000.0.266 | Indicate the beginning of Alignment Process | ||
| NTF bsaAlignmentFinished | 1.3.6.1.4.1.4458.1000.0.267 | Indicate the completion of Alignment Process | ||
| NTF bsaAlignmentTriggered | 1.3.6.1.4.1.4458.1000.0.268 | Indicate the triggering of Alignment Process due to exceeding thresholds | ||
| winlink1000Odu | 1.3.6.1.4.1.4458.1000.1 | |||
| winlink1000OduAdmin | 1.3.6.1.4.1.4458.1000.1.1 | |||
| STR winlink1000OduAdmProductType | 1.3.6.1.4.1.4458.1000.1.1.1 | DisplayString | read-only | ODU configuration description. |
| STR winlink1000OduAdmHwRev | 1.3.6.1.4.1.4458.1000.1.1.2 | DisplayString | read-only | ODU Hardware Version. |
| STR winlink1000OduAdmSwRev | 1.3.6.1.4.1.4458.1000.1.1.3 | DisplayString | read-only | ODU Software Version. |
| STR winlink1000OduAdmLinkName | 1.3.6.1.4.1.4458.1000.1.1.4 | DisplayString | read-write | Link Name. A change is effective immediately. |
| INT winlink1000OduAdmResetCmd | 1.3.6.1.4.1.4458.1000.1.1.5 | INTEGER | read-write | Reset Command. A set command with a value of 3 will cause a device reset. HBS only: A set command with a value of 4 will cause a device reset for the entire sector. The read value is always 0. |
| IP winlink1000OduAdmAddres | 1.3.6.1.4.1.4458.1000.1.1.6 | IpAddress | read-write | ODU IP address. A change is effective after reset. The parameter is kept for backward compatibility. Using the alternative parameter: winlink1000OduAdmIpParamsCnfg is recommended. |
| IP winlink1000OduAdmMask | 1.3.6.1.4.1.4458.1000.1.1.7 | IpAddress | read-write | ODU Subnet Mask. A change is effective after reset. The parameter is kept for backward compatibility. Using the alternative parameter: winlink1000OduAdmIpParamsCnfg is recommended. |
| IP winlink1000OduAdmGateway | 1.3.6.1.4.1.4458.1000.1.1.8 | IpAddress | read-write | ODU default gateway. A change is effective after reset. The parameter is kept for backward compatibility. Using the alternative parameter: winlink1000OduAdmIpParamsCnfg is recommended. |
| INT winlink1000OduAdmBroadcast | 1.3.6.1.4.1.4458.1000.1.1.10 | INTEGER | read-write | This parameter is reserved for the Manager application provided with the product. |
| winlink1000OduAdmHostsTable | 1.3.6.1.4.1.4458.1000.1.1.12 | not-accessible | Trap destinations table. Each trap destination is defined by an IP address and a UDP port. Up to 10 addresses can be configured. | |
| winlink1000OduAdmHostsEntry | 1.3.6.1.4.1.4458.1000.1.1.12.1 | not-accessible | Trap destinations table entry. | |
| INT winlink1000OduAdmHostsIndex | 1.3.6.1.4.1.4458.1000.1.1.12.1.1 | INTEGER | read-only | Trap destinations table index. |
| IP winlink1000OduAdmHostsIp | 1.3.6.1.4.1.4458.1000.1.1.12.1.2 | IpAddress | read-write | Trap destination IP address. A change is effective immediately. |
| INT winlink1000OduAdmHostsPort | 1.3.6.1.4.1.4458.1000.1.1.12.1.3 | INTEGER | read-write | UDP port of the trap destination. A change is effective immediately. |
| INT winlink1000OduAdmHostsSecurityModel | 1.3.6.1.4.1.4458.1000.1.1.12.1.4 | INTEGER | read-write | Security model used for this trap generation. |
| STR winlink1000OduAdmHostsUserName | 1.3.6.1.4.1.4458.1000.1.1.12.1.5 | DisplayString | read-write | User name used to generate the snmpv3 trap. |
| STR winlink1000OduAdmHostsPassword | 1.3.6.1.4.1.4458.1000.1.1.12.1.6 | DisplayString | read-write | Password used to generate the snmpv3 trap. |
| STR winlink1000OduAdmHostsIPv6 | 1.3.6.1.4.1.4458.1000.1.1.12.1.7 | DisplayString | read-write | Trap destination IPv6 address. A change is effective immediately. |
| INT winlink1000OduBuzzerAdminState | 1.3.6.1.4.1.4458.1000.1.1.13 | INTEGER | read-write | This parameter controls the activation of the buzzer while the unit is in install mode. A change is effective immediately. The valid values are: disabled (0), enabledAuto (1), enabledConstantly(2), advancedAuto (3). |
| STR winlink1000OduProductId | 1.3.6.1.4.1.4458.1000.1.1.14 | DisplayString | read-only | This parameter is reserved for the Manager application provided with the product. |
| STR winlink1000OduReadCommunity | 1.3.6.1.4.1.4458.1000.1.1.15 | DisplayString | read-write | Read Community String. This parameter always returns ***** when retrieving its value. It is used by the Manager application to change the Read Community String. The SNMP agent accepts only encrypted values. |
| STR winlink1000OduReadWriteCommunity | 1.3.6.1.4.1.4458.1000.1.1.16 | DisplayString | read-write | Read/Write Community String. This parameter always returns ***** when retrieving its value. It is used by the Manager application to change the Read/Write Community String. The SNMP agent accepts only encrypted values. |
| STR winlink1000OduTrapCommunity | 1.3.6.1.4.1.4458.1000.1.1.17 | DisplayString | read-write | Trap Community String. This parameter is used by the Manager application to change the Trap Community String. The SNMP agent accepts only encrypted values. |
| INT winlink1000OduAdmSnmpAgentVersion | 1.3.6.1.4.1.4458.1000.1.1.18 | INTEGER | read-only | Major version of the SNMP agent. |
| STR winlink1000OduAdmRemoteSiteName | 1.3.6.1.4.1.4458.1000.1.1.19 | DisplayString | read-only | Remote site name. Returns the same value as sysLocation parameter of the remote site. |
| INT winlink1000OduAdmSnmpAgentMinorVersion | 1.3.6.1.4.1.4458.1000.1.1.20 | INTEGER | read-only | Minor version of the SNMP agent. |
| STR winlink1000OduAdmLinkPassword | 1.3.6.1.4.1.4458.1000.1.1.21 | DisplayString | read-write | Link Password. This parameter always returns ***** when retrieving its value. It is used by the Manager application to change the Link Password. The SNMP agent accepts only encrypted values. |
| STR winlink1000OduAdmSiteLinkPassword | 1.3.6.1.4.1.4458.1000.1.1.22 | DisplayString | read-write | Site Link Password. This parameter always returns ***** when retrieving its value. It is used by the Manager application to change the Link Password of the site. The SNMP agent accepts only encrypted values. |
| INT winlink1000OduAdmDefaultPassword | 1.3.6.1.4.1.4458.1000.1.1.23 | INTEGER | read-only | This parameter indicates if the current Link Password is the default password. |
| INT winlink1000OduAdmConnectionType | 1.3.6.1.4.1.4458.1000.1.1.24 | INTEGER | read-only | This parameter indicates if the Manager application is connected to the local ODU or to the remote ODU over the air. A value of 'unknown' indicates community string mismatch. |
| INT winlink1000OduAdmBackToFactorySettingsCmd | 1.3.6.1.4.1.4458.1000.1.1.25 | INTEGER | read-write | Back to factory settings Command. A change is effective after reset. The read value is always 0. |
| STR winlink1000OduAdmIpParamsCnfg | 1.3.6.1.4.1.4458.1000.1.1.26 | DisplayString | read-write | ODU IP address Configuration. The format is: ||| |
| INT winlink1000OduAdmVlanID | 1.3.6.1.4.1.4458.1000.1.1.27 | INTEGER | read-write | VLAN ID. Valid values are 1 to 4094. Initial value is 0 meaning VLAN unaware. |
| INT winlink1000OduAdmVlanPriority | 1.3.6.1.4.1.4458.1000.1.1.28 | INTEGER | read-write | VLAN Priority. 0 is lowest priority, 7 is highest priority. |
| STR winlink1000OduAdmSN | 1.3.6.1.4.1.4458.1000.1.1.29 | DisplayString | read-only | ODU Serial Number |
| STR winlink1000OduAdmProductName | 1.3.6.1.4.1.4458.1000.1.1.30 | DisplayString | read-only | This is the product name as it exists at EC |
| STR winlink1000OduAdmActivationKey | 1.3.6.1.4.1.4458.1000.1.1.31 | DisplayString | read-write | Activates a general key. |
| STR winlink1000OduAdmRmtPermittedOduType | 1.3.6.1.4.1.4458.1000.1.1.32 | DisplayString | read-write | Mobile Application: permitted partner OduType. |
| INT winlink1000OduAdmCpuID | 1.3.6.1.4.1.4458.1000.1.1.33 | INTEGER | read-only | CPU ID |
| STR winlink1000OduAdmOvrdCmd | 1.3.6.1.4.1.4458.1000.1.1.34 | DisplayString | read-write | Ability to perform special command in the ODU. |
| INT winlink1000OduAdmLinkMode | 1.3.6.1.4.1.4458.1000.1.1.35 | INTEGER | read-write | Unit PMP operation mode. |
| INT winlink1000OduAdmActualConnectMode | 1.3.6.1.4.1.4458.1000.1.1.36 | INTEGER | read-only | Unit connected as part to ptp or ptmp. |
| INT winlink1000OduAdmAES256Support | 1.3.6.1.4.1.4458.1000.1.1.37 | INTEGER | read-only | AES-256 security support indication. |
| INT winlink1000OduAdmAES256State | 1.3.6.1.4.1.4458.1000.1.1.38 | INTEGER | read-write | Enable/Disable AES-256 security mode over the air link. |
| INT winlink1000OduAdmAES256Status | 1.3.6.1.4.1.4458.1000.1.1.39 | INTEGER | read-only | AES256 operating status |
| INT winlink1000OduAdmBatterySavingShutdownTime | 1.3.6.1.4.1.4458.1000.1.1.40 | INTEGER | read-write | Battery Saving Shutdown Time in minutes, 0 till battery run out, -1 if not supported. |
| INT winlink1000OduAdmWiFiPowerMode | 1.3.6.1.4.1.4458.1000.1.1.41 | INTEGER | read-write | WIFI unit power mode. |
| INT winlink1000OduAdmShutdownTimer | 1.3.6.1.4.1.4458.1000.1.1.42 | INTEGER | read-only | Shutdown Timer in seconds. |
| INT winlink1000OduAdmGPSState | 1.3.6.1.4.1.4458.1000.1.1.43 | INTEGER | read-only | GPS state |
| INT winlink1000OduAdmTemperatureC | 1.3.6.1.4.1.4458.1000.1.1.44 | INTEGER | read-only | The temperature (Celsius) inside the Board. |
| INT winlink1000OduAdmIPStackMode | 1.3.6.1.4.1.4458.1000.1.1.45 | INTEGER | read-write | The IP stack mode. |
| STR winlink1000OduAdmIPv6ParamsCnfg | 1.3.6.1.4.1.4458.1000.1.1.46 | DisplayString | read-write | ODU IPv6 address Configuration. The format is: ||| |
| STR winlink1000OduAdmIPv6Address | 1.3.6.1.4.1.4458.1000.1.1.47 | DisplayString | read-only | ODU IPv6 address. |
| INT winlink1000OduAdmIPv6Prefix | 1.3.6.1.4.1.4458.1000.1.1.48 | INTEGER | read-only | ODU IPv6 subnet mask. |
| STR winlink1000OduAdmIPv6DefaultGateWay | 1.3.6.1.4.1.4458.1000.1.1.49 | DisplayString | read-only | ODU IPv6 default gateway. |
| INT winlink1000OduAdmPowerConsumption | 1.3.6.1.4.1.4458.1000.1.1.50 | INTEGER | read-only | Power Consumption (mWatt) |
| winlink1000OduAdmWifi | 1.3.6.1.4.1.4458.1000.1.1.51 | |||
| INT winlink1000OduAdmWifiChannel | 1.3.6.1.4.1.4458.1000.1.1.51.1 | INTEGER | read-write | Wifi Channel |
| INT winlink1000OduAdmWifiTxPower | 1.3.6.1.4.1.4458.1000.1.1.51.2 | INTEGER | read-write | Wifi TX Power |
| STR winlink1000OduAdmWifiSSID | 1.3.6.1.4.1.4458.1000.1.1.51.3 | DisplayString | read-only | Wifi SSID |
| INT winlink1000OduAdmWifiSecurityType | 1.3.6.1.4.1.4458.1000.1.1.51.4 | INTEGER | read-only | Wifi Security type |
| STR winlink1000OduAdmWifiPassword | 1.3.6.1.4.1.4458.1000.1.1.51.5 | DisplayString | read-write | Wifi Password |
| IP winlink1000OduAdmWifiNetwork | 1.3.6.1.4.1.4458.1000.1.1.51.6 | IpAddress | read-write | Wifi Network |
| INT winlink1000OduAdmWifiRssi | 1.3.6.1.4.1.4458.1000.1.1.51.7 | INTEGER | read-only | Wifi RSSI |
| STR winlink1000OduAdmWifiStationMAC | 1.3.6.1.4.1.4458.1000.1.1.51.8 | DisplayString | read-only | Wifi Station MAC |
| INT winlink1000OduAdmWifiRestart | 1.3.6.1.4.1.4458.1000.1.1.51.9 | INTEGER | read-write | A set command with a value of 1 will cause a Wifi restart. The read value is always 0. |
| INT winlink1000OduAdmWifiApStatus | 1.3.6.1.4.1.4458.1000.1.1.51.10 | INTEGER | read-only | Wifi AP Status |
| INT winlink1000OduAdmBsaOperationMode | 1.3.6.1.4.1.4458.1000.1.1.52 | INTEGER | read-only | BSA Operation Mode |
| STR winlink1000OduAdmMngConnection | 1.3.6.1.4.1.4458.1000.1.1.53 | DisplayString | read-write | Management Connection |
| INT winlink1000OduAdm1588TCSupport | 1.3.6.1.4.1.4458.1000.1.1.54 | INTEGER | read-only | Indicates that 1588TC license activated |
| INT winlink1000OduAdmSyncESupport | 1.3.6.1.4.1.4458.1000.1.1.55 | INTEGER | read-only | ndicates that SyncE license activated |
| STR winlink1000OduAdmRadioRev | 1.3.6.1.4.1.4458.1000.1.1.56 | DisplayString | read-only | Radio Revision |
| STR winlink1000OduAdmProductRev | 1.3.6.1.4.1.4458.1000.1.1.57 | DisplayString | read-only | Product Revision |
| INT winlink1000OduAdmPMPSUSupport | 1.3.6.1.4.1.4458.1000.1.1.58 | INTEGER | read-only | Indicates that PMP SU license is activated |
| STR winlink1000OduAdmManagerDownloadURL | 1.3.6.1.4.1.4458.1000.1.1.59 | DisplayString | read-write | This is the URL from which management tool can be downloaded |
| STR winlink1000OduAdmAntennaDescription | 1.3.6.1.4.1.4458.1000.1.1.60 | DisplayString | read-only | The is a description of the antenna connected to the ODU |
| STR winlink1000OduAdmSwCapabilities | 1.3.6.1.4.1.4458.1000.1.1.61 | DisplayString | read-only | This is used to describe which Software Capabilities the current ODU supports |
| winlink1000OduService | 1.3.6.1.4.1.4458.1000.1.2 | |||
| INT winlink1000OduSrvMode | 1.3.6.1.4.1.4458.1000.1.2.1 | INTEGER | read-write | System mode. The only values that can be set are installMode and slaveMode; normalMode reserved to the Manager application provided with the product. A change is effective after link re-synchronization. |
| INT winlink1000OduSrvBridging | 1.3.6.1.4.1.4458.1000.1.2.3 | INTEGER | read-only | Bridging Mode. Valid values are: disabled (0), enabled (1). |
| winlink1000OduServiceRingTopology | 1.3.6.1.4.1.4458.1000.1.2.4 | |||
| INT winlink1000OduSrvRingLinkMode | 1.3.6.1.4.1.4458.1000.1.2.4.1 | INTEGER | read-write | Mode of the link regarding ring topology. |
| INT winlink1000OduSrvRingTopologySupported | 1.3.6.1.4.1.4458.1000.1.2.4.2 | INTEGER | read-only | Ring Topology, options are: supported, not supported |
| winlink1000OduSrvRingVlanIdTable | 1.3.6.1.4.1.4458.1000.1.2.4.3 | not-accessible | Ring VLAN IDs table. | |
| winlink1000OduSrvRingVlanIdEntry | 1.3.6.1.4.1.4458.1000.1.2.4.3.1 | not-accessible | VLAN ID of the internal ring messages. Valid values are 1 to 4094. Initial value is 0 meaning VLAN unaware. | |
| INT winlink1000OduSrvRingVlanIdIndex | 1.3.6.1.4.1.4458.1000.1.2.4.3.1.1 | INTEGER | read-only | Index of VLAN ID of the internal ring messages. |
| INT winlink1000OduSrvRingVlanId | 1.3.6.1.4.1.4458.1000.1.2.4.3.1.2 | INTEGER | read-write | VLAN ID of the internal ring messages. Valid values are 1 to 4094. Initial value is 0 meaning VLAN unaware. |
| INT winlink1000OduSrvRingEthStatus | 1.3.6.1.4.1.4458.1000.1.2.4.4 | INTEGER | read-only | Represents the Ethernet service blocking state of a Rings link |
| INT winlink1000OduSrvRingMaxAllowedTimeFromLastRpm | 1.3.6.1.4.1.4458.1000.1.2.4.5 | INTEGER | read-write | Defines the minimal time (in ms) required for determination of ring failure. |
| INT winlink1000OduSrvRingWTR | 1.3.6.1.4.1.4458.1000.1.2.4.6 | INTEGER | read-write | Defines the minimal time (in ms) required for ring recovery. |
| winlink1000OduServiceQoS | 1.3.6.1.4.1.4458.1000.1.2.5 | |||
| INT winlink1000OduSrvQoSMode | 1.3.6.1.4.1.4458.1000.1.2.5.1 | INTEGER | read-write | Mode of QoS feature. |
| winlink1000OduSrvQoSConfTable | 1.3.6.1.4.1.4458.1000.1.2.5.2 | not-accessible | QoS configuration table. | |
| winlink1000OduSrvQoSConfEntry | 1.3.6.1.4.1.4458.1000.1.2.5.2.1 | not-accessible | QoS configuration table. | |
| INT winlink1000OduSrvQoSConfIndex | 1.3.6.1.4.1.4458.1000.1.2.5.2.1.1 | INTEGER | read-only | Index of QoS Configuration. |
| INT winlink1000OduSrvConfVlanQGroups | 1.3.6.1.4.1.4458.1000.1.2.5.2.1.2 | INTEGER | read-only | Frames classification according to VLAN Priority IDs. |
| INT winlink1000OduSrvConfDiffservQGroups | 1.3.6.1.4.1.4458.1000.1.2.5.2.1.3 | INTEGER | read-only | Frames classification according to Diffserv. |
| INT winlink1000OduSrvConfQueMir | 1.3.6.1.4.1.4458.1000.1.2.5.2.1.4 | INTEGER | read-write | Desired Private MIR. |
| INT winlink1000OduSrvConfQueWeight | 1.3.6.1.4.1.4458.1000.1.2.5.2.1.5 | INTEGER | read-write | QoS queueu's weights in percent. |
| STR winlink1000OduSrvQoSVlanQGroupsSetStr | 1.3.6.1.4.1.4458.1000.1.2.5.3 | DisplayString | read-write | Frames classification according to VLAN IDs string for set. |
| STR winlink1000OduSrvQoSDiffservQGroupsSetStr | 1.3.6.1.4.1.4458.1000.1.2.5.4 | DisplayString | read-write | Frames classification according to Diffserv IDs string for set. |
| INT winlink1000OduSrvQoSMaxRTQuePercent | 1.3.6.1.4.1.4458.1000.1.2.5.5 | INTEGER | read-only | Maximal percent for RT & NRT queues. |
| winlink1000OduServiceVlan | 1.3.6.1.4.1.4458.1000.1.2.6 | |||
| INT winlink1000OduSrvVlanSupport | 1.3.6.1.4.1.4458.1000.1.2.6.1 | INTEGER | read-only | ODU Ethernet port VLAN support and configuration availability indication. 1 - ODU VLAN Functionality Not Supported 2 - ODU VLAN Functionality Supported 3 - ODU VLAN Functionality Supported and Available |
| INT winlink1000OduSrvVlanIngressMode | 1.3.6.1.4.1.4458.1000.1.2.6.2 | INTEGER | read-write | ODU Ethernet port ingress VLAN mode. |
| INT winlink1000OduSrvVlanEgressMode | 1.3.6.1.4.1.4458.1000.1.2.6.3 | INTEGER | read-write | ODU Ethernet port egress VLAN mode. |
| INT winlink1000OduSrvEgressTag | 1.3.6.1.4.1.4458.1000.1.2.6.4 | INTEGER | read-write | ODU ethernet port egress VLAN tag. Right most digit is Vlan priority (0-7), other digits compose Vlan Id (2-4094) |
| INT winlink1000OduSrvEgressProviderTag | 1.3.6.1.4.1.4458.1000.1.2.6.5 | INTEGER | read-write | ODU ethernet port egress Provider VLAN tag. Right most digit is Vlan priority (0-7), other digits compose Vlan Id (2-4094) |
| STR winlink1000OduSrvVlanIngressAllowedVIDs | 1.3.6.1.4.1.4458.1000.1.2.6.6 | DisplayString | read-write | ODU ethernet port VLAN IDs that will not be filtered on ingress. w|w|w|w|w|w|w|w| ( where w = {0-4094} and w != 1 ) |
| INT winlink1000OduSrvVlanDisable | 1.3.6.1.4.1.4458.1000.1.2.6.7 | INTEGER | read-write | Disable VLAN functionality. The following values can be set: 3 - Disable ODU & IDU VLAN Configurations. |
| STR winlink1000OduServiceVlanProviderListTPIDstr | 1.3.6.1.4.1.4458.1000.1.2.6.8 | DisplayString | read-only | Holds the possible Provider TPIDs. |
| winlink1000OduEthernet | 1.3.6.1.4.1.4458.1000.1.3 | |||
| INT winlink1000OduEthernetRemainingRate | 1.3.6.1.4.1.4458.1000.1.3.1 | INTEGER | read-only | Current Ethernet bandwidth in bps. |
| winlink1000OduEthernetIfTable | 1.3.6.1.4.1.4458.1000.1.3.2 | not-accessible | ODU Ethernet Interface table. | |
| winlink1000OduEthernetIfEntry | 1.3.6.1.4.1.4458.1000.1.3.2.1 | not-accessible | ODU Ethernet Interface table entry. | |
| INT winlink1000OduEthernetIfIndex | 1.3.6.1.4.1.4458.1000.1.3.2.1.1 | INTEGER | read-only | ODU Ethernet Interface Index. |
| STR winlink1000OduEthernetIfAddress | 1.3.6.1.4.1.4458.1000.1.3.2.1.5 | DisplayString | read-only | ODU MAC address. |
| INT winlink1000OduEthernetIfAdminStatus | 1.3.6.1.4.1.4458.1000.1.3.2.1.6 | INTEGER | read-write | Required state of the interface. |
| INT winlink1000OduEthernetIfOperStatus | 1.3.6.1.4.1.4458.1000.1.3.2.1.7 | INTEGER | read-only | Current operational state of the interface. |
| INT winlink1000OduEthernetIfFailAction | 1.3.6.1.4.1.4458.1000.1.3.2.1.8 | INTEGER | read-write | Failure action of the interface. |
| INT winlink1000OduEthernetIf1588v2PTPEventRXRate | 1.3.6.1.4.1.4458.1000.1.3.2.1.9 | INTEGER | read-only | For debug use |
| INT winlink1000OduEthernetIf1588v2PTPEventTXRate | 1.3.6.1.4.1.4458.1000.1.3.2.1.10 | INTEGER | read-only | For debug use |
| INT winlink1000OduEthernetNumOfPorts | 1.3.6.1.4.1.4458.1000.1.3.3 | INTEGER | read-only | Number of ODU network interfaces. |
| INT winlink1000OduEthernetGbeSupported | 1.3.6.1.4.1.4458.1000.1.3.4 | INTEGER | read-only | Supported Giga bit Ethernet in ODU. |
| STR winlink1000OduEthernetSfpProperties | 1.3.6.1.4.1.4458.1000.1.3.5 | DisplayString | read-only | Sfp port properties. |
| winlink1000OduBridge | 1.3.6.1.4.1.4458.1000.1.4 | |||
| winlink1000OduBridgeBase | 1.3.6.1.4.1.4458.1000.1.4.1 | |||
| winlink1000OduBridgeBasePortTable | 1.3.6.1.4.1.4458.1000.1.4.1.4 | not-accessible | ODU Bridge Ports table. | |
| winlink1000OduBridgeBasePortEntry | 1.3.6.1.4.1.4458.1000.1.4.1.4.1 | not-accessible | ODU Bridge Ports table entry. | |
| INT winlink1000OduBridgeBasePortIndex | 1.3.6.1.4.1.4458.1000.1.4.1.4.1.1 | INTEGER | read-only | ODU Bridge Port Number. |
| INT winlink1000OduBridgeBaseIfIndex | 1.3.6.1.4.1.4458.1000.1.4.1.4.1.2 | INTEGER | read-only | IfIndex corresponding to ODU Bridge port. |
| winlink1000OduBridgeTp | 1.3.6.1.4.1.4458.1000.1.4.4 | |||
| winlink1000OduBridgeTpPortTable | 1.3.6.1.4.1.4458.1000.1.4.4.3 | not-accessible | ODU Transparent Bridge Ports table. | |
| winlink1000OduBridgeTpPortEntry | 1.3.6.1.4.1.4458.1000.1.4.4.3.1 | not-accessible | ODU Transparent Bridge Ports table entry. | |
| INT winlink1000OduBridgeTpPortIndex | 1.3.6.1.4.1.4458.1000.1.4.4.3.1.1 | INTEGER | read-only | ODU Transparent Bridge Port Number. |
| CTR winlink1000OduBridgeTpPortInFrames | 1.3.6.1.4.1.4458.1000.1.4.4.3.1.3 | Counter | read-only | Number of frames received by this port. |
| CTR winlink1000OduBridgeTpPortOutFrames | 1.3.6.1.4.1.4458.1000.1.4.4.3.1.4 | Counter | read-only | Number of frames transmitted by this port. |
| CTR winlink1000OduBridgeTpPortInBytes | 1.3.6.1.4.1.4458.1000.1.4.4.3.1.101 | Counter | read-only | Number of bytes received by this port. |
| CTR winlink1000OduBridgeTpPortOutBytes | 1.3.6.1.4.1.4458.1000.1.4.4.3.1.102 | Counter | read-only | Number of bytes transmitted by this port. |
| INT winlink1000OduBridgeTpMode | 1.3.6.1.4.1.4458.1000.1.4.4.101 | INTEGER | read-write | ODU bridge mode. A change is effective after reset. Valid values: hubMode (0), bridgeMode (1). |
| INT winlink1000OduBridgeConfigMode | 1.3.6.1.4.1.4458.1000.1.4.4.102 | INTEGER | read-only | ODU bridge configuration mode |
| winlink1000OduAir | 1.3.6.1.4.1.4458.1000.1.5 | |||
| INT winlink1000OduAirFreq | 1.3.6.1.4.1.4458.1000.1.5.1 | INTEGER | read-write | Installation Center Frequency. Valid values are product dependent. A change is effective after link re-synchronization. |
| INT winlink1000OduAirDesiredRate | 1.3.6.1.4.1.4458.1000.1.5.2 | INTEGER | read-write | Deprecated parameter, actual behavior is read-only. Required Air Rate. For Channel Bandwidth of 20, 10, 5 MHz divide the value by 1, 2, 4 respectively. |
| STR winlink1000OduAirSSID | 1.3.6.1.4.1.4458.1000.1.5.3 | DisplayString | read-write | Reserved for the Manager application provided with the product. The Sector ID in Point-To-Multi-Point systems. |
| INT winlink1000OduAirTxPower | 1.3.6.1.4.1.4458.1000.1.5.4 | INTEGER | read-write | Required Transmit power in dBm . This is a nominal value while the actual transmit power includes additional attenuation. The min and max values are product specific. A change is effective immediately. |
| INT winlink1000OduAirSesState | 1.3.6.1.4.1.4458.1000.1.5.5 | INTEGER | read-only | Current Link State. The value is active (3) during normal operation. |
| INT winlink1000OduAirMstrSlv | 1.3.6.1.4.1.4458.1000.1.5.6 | INTEGER | read-only | This parameter indicates if the device was automatically selected into the radio link master or slave. The value is undefined if there is no link. The value is relevant only for point to point systems. |
| INT winlink1000OduAirResync | 1.3.6.1.4.1.4458.1000.1.5.8 | INTEGER | read-write | Setting this parameter to 1 will cause the link to restart the synchronization process. |
| winlink1000OduAirPerf | 1.3.6.1.4.1.4458.1000.1.5.9 | |||
| INT winlink1000OduAirRxPower | 1.3.6.1.4.1.4458.1000.1.5.9.1 | INTEGER | read-only | Received Signal Strength in dBm. Relevant only for point to point systems. |
| CTR winlink1000OduAirTotalFrames | 1.3.6.1.4.1.4458.1000.1.5.9.2 | Counter | read-only | Total number of radio frames. |
| CTR winlink1000OduAirBadFrames | 1.3.6.1.4.1.4458.1000.1.5.9.3 | Counter | read-only | Total number of received radio frames with CRC error. The value is relevant only for point to point systems . |
| INT winlink1000OduAirCurrentRate | 1.3.6.1.4.1.4458.1000.1.5.9.4 | INTEGER | read-only | Deprecated parameter. Actual rate of the air interface in Mbps. For Channel Bandwidth of 20, 10, 5 MHz divide the value by 1, 2, 4 respectively. |
| INT winlink1000OduAirCurrentRateIdx | 1.3.6.1.4.1.4458.1000.1.5.9.5 | INTEGER | read-only | Index of current air rate. |
| OCT winlink1000OduAirChainsRxPower | 1.3.6.1.4.1.4458.1000.1.5.9.6 | OCTET STRING | read-only | Received Signal Strength of Cpe chains in dBm. Chain 1 RSS: (1 Byte) Chain 2 RSS: (1 Byte) Chain 3 RSS: (1 Byte) |
| INT winlink1000OduAirCurrentRateCBW | 1.3.6.1.4.1.4458.1000.1.5.9.7 | INTEGER | read-only | CBW of current air rate. |
| INT winlink1000OduAirCurrentRateGI | 1.3.6.1.4.1.4458.1000.1.5.9.8 | INTEGER | read-only | GI of current air rate. |
| INT winlink1000OduAirTxPower36 | 1.3.6.1.4.1.4458.1000.1.5.10 | INTEGER | read-write | Deprecated parameter. Actual behavior is read-only. |
| INT winlink1000OduAirTxPower48 | 1.3.6.1.4.1.4458.1000.1.5.11 | INTEGER | read-write | Deprecated parameter. Actual behavior is read-only. |
| INT winlink1000OduAirCurrentTxPower | 1.3.6.1.4.1.4458.1000.1.5.12 | INTEGER | read-only | Current Transmit Power in dBm. This is a nominal value while the actual transmit power includes additional attenuation. |
| INT winlink1000OduAirMinFrequency | 1.3.6.1.4.1.4458.1000.1.5.13 | INTEGER | read-only | Minimum center frequency in MHz. |
| INT winlink1000OduAirMaxFrequency | 1.3.6.1.4.1.4458.1000.1.5.14 | INTEGER | read-only | Maximum center frequency in MHz. |
| INT winlink1000OduAirFreqResolution | 1.3.6.1.4.1.4458.1000.1.5.15 | INTEGER | read-only | Center Frequency resolution. Measured in MHz if value < 100, otherwise in KHz. |
| INT winlink1000OduAirCurrentFreq | 1.3.6.1.4.1.4458.1000.1.5.16 | INTEGER | read-only | Current Center Frequency. Measured in MHz if center frequency resolution value < 100, otherwise in KHz. |
| INT winlink1000OduAirNumberOfChannels | 1.3.6.1.4.1.4458.1000.1.5.17 | INTEGER | read-only | Number of channels that can be used. |
| winlink1000OduAirChannelsTable | 1.3.6.1.4.1.4458.1000.1.5.18 | not-accessible | Table of channels used by automatic channels selection (ACS). | |
| winlink1000OduAirChannelsEntry | 1.3.6.1.4.1.4458.1000.1.5.18.1 | not-accessible | ACS channels table entry. | |
| INT winlink1000OduAirChannelsIndex | 1.3.6.1.4.1.4458.1000.1.5.18.1.1 | INTEGER | read-only | Channel Index. |
| INT winlink1000OduAirChannelsFrequency | 1.3.6.1.4.1.4458.1000.1.5.18.1.2 | INTEGER | read-only | Channel frequency in MHz. |
| INT winlink1000OduAirChannelsOperState | 1.3.6.1.4.1.4458.1000.1.5.18.1.3 | INTEGER | read-write | Channel state. Can be set by the user. Automatic Channel Selection uses channels that are AirChannelsOperState enabled and AirChannelsAvail enabled. A change is effective after link re-synchronization. Valid values: disabled (0), enabled (1). Rewriteable only in Point-To-Point products. |
| INT winlink1000OduAirChannelsAvail | 1.3.6.1.4.1.4458.1000.1.5.18.1.4 | INTEGER | read-only | Channel state. Product specific and cannot be changed by the user. Automatic Channel Selection uses channels that are AirChannelsOperState enabled and AirChannelsAvail enabled. Valid values: disabled (0), enabled (1). |
| INT winlink1000OduAirChannelsDefaultFreq | 1.3.6.1.4.1.4458.1000.1.5.18.1.5 | INTEGER | read-only | Default channel's availability for all CBWs. The valid values are: forbidden (0), available (1). |
| INT winlink1000OduAirDfsState | 1.3.6.1.4.1.4458.1000.1.5.19 | INTEGER | read-only | Radar detection state. Valid values: disabled (0), enabled (1). |
| INT winlink1000OduAirAutoChannelSelectionState | 1.3.6.1.4.1.4458.1000.1.5.20 | INTEGER | read-only | Deprecated parameter. Indicating Automatic Channel Selection availability at current channel bandwidth. Valid values: disabled (0), enabled (1). |
| INT winlink1000OduAirEnableTxPower | 1.3.6.1.4.1.4458.1000.1.5.21 | INTEGER | read-only | Indicating Transmit power configuration enabled or disabled. |
| INT winlink1000OduAirMinTxPower | 1.3.6.1.4.1.4458.1000.1.5.22 | INTEGER | read-only | Minimum Transmit power in dBm. |
| winlink1000OduAirMaxTxPowerTable | 1.3.6.1.4.1.4458.1000.1.5.23 | not-accessible | Table of Maximum transmit power per air rate, in dBm. | |
| winlink1000OduAirMaxTxPowerEntry | 1.3.6.1.4.1.4458.1000.1.5.23.1 | not-accessible | Maximum Transmit power table entry. | |
| INT winlink1000OduAirMaxTxPowerIndex | 1.3.6.1.4.1.4458.1000.1.5.23.1.1 | INTEGER | read-only | Air interface rate index. |
| INT winlink1000OduAirMaxTxPower | 1.3.6.1.4.1.4458.1000.1.5.23.1.2 | INTEGER | read-only | Maximum Transmit power in dBm. |
| INT winlink1000OduAirChannelBandwidth | 1.3.6.1.4.1.4458.1000.1.5.24 | INTEGER | read-write | Channel bandwidth in KHz. A change is effective after reset. |
| winlink1000OduAirChannelBWTable | 1.3.6.1.4.1.4458.1000.1.5.25 | not-accessible | Channel Bandwidths table. | |
| winlink1000OduAirChannelBWEntry | 1.3.6.1.4.1.4458.1000.1.5.25.1 | not-accessible | Channel Bandwidth table entry. | |
| INT winlink1000OduAirChannelBWIndex | 1.3.6.1.4.1.4458.1000.1.5.25.1.1 | INTEGER | read-only | Channel Bandwidth index. |
| INT winlink1000OduAirChannelBWAvail | 1.3.6.1.4.1.4458.1000.1.5.25.1.2 | INTEGER | read-only | Channel Bandwidth availability, product specific. Options are: Not supported, supported with manual channel selection, supported with Automatic Channel Selection. |
| STR winlink1000OduAirChannelsAdminState | 1.3.6.1.4.1.4458.1000.1.5.25.1.3 | DisplayString | read-only | Channels' availability per CBW. |
| INT winlink1000OduAirChannelBWHSSATDDConflictPerCBW | 1.3.6.1.4.1.4458.1000.1.5.25.1.4 | INTEGER | read-only | Indication for possible Link drop per CBW due to conflict between HSS and ATDD. |
| INT winlink1000OduAirChannelBWMinRatioForSupporting | 1.3.6.1.4.1.4458.1000.1.5.25.1.5 | INTEGER | read-only | Minimal TX ratio that may be used by the HSM and still enable proper operation of the aforementioned CBW. |
| INT winlink1000OduAirChannelBWMaxRatioForSupporting | 1.3.6.1.4.1.4458.1000.1.5.25.1.6 | INTEGER | read-only | Maximal TX ratio that may be used by the HSM and still enable proper operation of the aforementioned CBW. |
| INT winlink1000OduAirRFD | 1.3.6.1.4.1.4458.1000.1.5.26 | INTEGER | read-only | Current radio frame duration in microseconds. |
| winlink1000OduAirRatesTable | 1.3.6.1.4.1.4458.1000.1.5.27 | not-accessible | Air Rate indexes table for current channel bandwidth. | |
| winlink1000OduAirRatesEntry | 1.3.6.1.4.1.4458.1000.1.5.27.1 | not-accessible | Air Rate indexes table entry. | |
| INT winlink1000OduAirRatesIndex | 1.3.6.1.4.1.4458.1000.1.5.27.1.1 | INTEGER | read-only | Air Rate index. |
| INT winlink1000OduAirRatesAvail | 1.3.6.1.4.1.4458.1000.1.5.27.1.2 | INTEGER | read-only | Air Rate availability, depending on air interface conditions. |
| INT winlink1000OduAirDesiredRateIdx | 1.3.6.1.4.1.4458.1000.1.5.28 | INTEGER | read-write | Required Air Rate index. 0 reserved for Adaptive Rate. A change is effective immediately after Set operation to the master side while the link is up. |
| INT winlink1000OduAirLinkDistance | 1.3.6.1.4.1.4458.1000.1.5.29 | INTEGER | read-only | Link distance in meters. A value of -1 indicates an illegal value and is also used when a link is not established. |
| INT winlink1000OduAirLinkWorkingMode | 1.3.6.1.4.1.4458.1000.1.5.30 | INTEGER | read-only | Link working mode as a result of comparing versions of both sides of the link. Possible modes are: Unknown - no link, Normal - versions on both sides are identical with full compatibility, with restricted compatibility, or versions on both sides are different with software upgrade or versions incompatibility. |
| INT winlink1000OduAirMajorLinkIfVersion | 1.3.6.1.4.1.4458.1000.1.5.31 | INTEGER | read-only | Major link interface version |
| INT winlink1000OduAirMinorLinkIfVersion | 1.3.6.1.4.1.4458.1000.1.5.32 | INTEGER | read-only | Minor link interface version |
| winlink1000OduAirHss | 1.3.6.1.4.1.4458.1000.1.5.40 | |||
| INT winlink1000OduAirHssDesiredOpState | 1.3.6.1.4.1.4458.1000.1.5.40.1 | INTEGER | read-write | Required Hub Site Synchronization operating state. For HssSyncUnits : For hssISU :[2,7] ,For hssGSU :[2,6] For HBS: [2,3,4,5] |
| INT winlink1000OduAirHssCurrentOpState | 1.3.6.1.4.1.4458.1000.1.5.40.2 | INTEGER | read-only | Current Hub Site Synchronization operating state. |
| INT winlink1000OduAirHssSyncStatus | 1.3.6.1.4.1.4458.1000.1.5.40.3 | INTEGER | read-only | Hub Site Synchronization sync status. |
| INT winlink1000OduAirHssExtPulseStatus | 1.3.6.1.4.1.4458.1000.1.5.40.4 | INTEGER | read-only | Hub Site Synchronization external pulse detection status. In GSS mode: if generating then 1PSP is auto generated by the GSS Unit. if generatingAndDetecting then 1PSP is generated by GPS satellites signal. |
| INT winlink1000OduAirHssExtPulseType | 1.3.6.1.4.1.4458.1000.1.5.40.5 | INTEGER | read-only | Hub Site Synchronization external pulse type. |
| INT winlink1000OduAirHssDesiredExtPulseType | 1.3.6.1.4.1.4458.1000.1.5.40.6 | INTEGER | read-write | Hub Site Synchronization required external pulse type. Valid values for read write: {typeA(2),typeB(3),typeC(4),typeD(5),typeE(6),typeF(7)}. Valid value for read only: {notApplicable(1)}. |
| winlink1000OduAirHssRfpTable | 1.3.6.1.4.1.4458.1000.1.5.40.7 | not-accessible | ODU Radio Frame Patterns (RFP) Table. | |
| winlink1000OduAirHssRfpEntry | 1.3.6.1.4.1.4458.1000.1.5.40.7.1 | not-accessible | ODU RFP Table entry. | |
| INT winlink1000OduAirHssRfpIndex | 1.3.6.1.4.1.4458.1000.1.5.40.7.1.1 | INTEGER | read-only | ODU RFP Table index. The index represent the Radio Frame Pattern: typeA(2), typeB(3), typeC(4), typeD(5),typeE(6),typeF(7). |
| INT winlink1000OduAirHssRfpEthChannelBW5MHz | 1.3.6.1.4.1.4458.1000.1.5.40.7.1.2 | INTEGER | read-only | Represents the compatibility of Ethernet service under Channel BW of 5MHz in the specific Radio Frame Pattern. |
| INT winlink1000OduAirHssRfpTdmChannelBW5MHz | 1.3.6.1.4.1.4458.1000.1.5.40.7.1.3 | INTEGER | read-only | Represents the compatibility of TDM service under Channel BW of 5MHz in the specific Radio Frame Pattern. |
| INT winlink1000OduAirHssRfpEthChannelBW10MHz | 1.3.6.1.4.1.4458.1000.1.5.40.7.1.4 | INTEGER | read-only | Represents the compatibility of Ethernet service under Channel BW of 10MHz in the specific Radio Frame Pattern. |
| INT winlink1000OduAirHssRfpTdmChannelBW10MHz | 1.3.6.1.4.1.4458.1000.1.5.40.7.1.5 | INTEGER | read-only | Represents the compatibility of TDM service under Channel BW of 10MHz in the specific Radio Frame Pattern. |
| INT winlink1000OduAirHssRfpEthChannelBW20MHz | 1.3.6.1.4.1.4458.1000.1.5.40.7.1.6 | INTEGER | read-only | Represents the compatibility of Ethernet service under Channel BW of 20MHz in the specific Radio Frame Pattern. |
| INT winlink1000OduAirHssRfpTdmChannelBW20MHz | 1.3.6.1.4.1.4458.1000.1.5.40.7.1.7 | INTEGER | read-only | Represents the compatibility of TDM service under Channel BW of 20MHz in the specific Radio Frame Pattern. |
| INT winlink1000OduAirHssRfpEthChannelBW40MHz | 1.3.6.1.4.1.4458.1000.1.5.40.7.1.8 | INTEGER | read-only | Represents the compatibility of Ethernet service under Channel BW of 40MHz in the specific Radio Frame Pattern. |
| INT winlink1000OduAirHssRfpTdmChannelBW40MHz | 1.3.6.1.4.1.4458.1000.1.5.40.7.1.9 | INTEGER | read-only | Represents the compatibility of TDM service under Channel BW of 40MHz in the specific Radio Frame Pattern. |
| INT winlink1000OduAirHssRfpEthChannelBW80MHz | 1.3.6.1.4.1.4458.1000.1.5.40.7.1.10 | INTEGER | read-only | Represents the compatibility of Ethernet service under Channel BW of 80MHz in the specific Radio Frame Pattern. |
| INT winlink1000OduAirHssRfpEthChannelBW7MHz | 1.3.6.1.4.1.4458.1000.1.5.40.7.1.11 | INTEGER | read-only | Represents the compatibility of Ethernet service under Channel BW of 7MHz in the specific Radio Frame Pattern. |
| INT winlink1000OduAirHssRfpEthChannelBW14MHz | 1.3.6.1.4.1.4458.1000.1.5.40.7.1.12 | INTEGER | read-only | Represents the compatibility of Ethernet service under Channel BW of 14MHz in the specific Radio Frame Pattern. |
| STR winlink1000OduAirHssRfpStr | 1.3.6.1.4.1.4458.1000.1.5.40.8 | DisplayString | read-only | Hub Site Synchronization supported patterns |
| INT winlink1000OduAirHssHsmID | 1.3.6.1.4.1.4458.1000.1.5.40.9 | INTEGER | read-only | A unique ID which is common to the HSM and all its collocated ODUs |
| STR winlink1000OduAirHssTime | 1.3.6.1.4.1.4458.1000.1.5.40.10 | DisplayString | read-only | Hub Site Synchronization GPS time |
| STR winlink1000OduAirHssLatitude | 1.3.6.1.4.1.4458.1000.1.5.40.11 | DisplayString | read-only | Hub Site Synchronization GPS Latitude |
| STR winlink1000OduAirHssNSIndicator | 1.3.6.1.4.1.4458.1000.1.5.40.12 | DisplayString | read-only | Hub Site Synchronization GPS N/S Indicator |
| STR winlink1000OduAirHssLongitude | 1.3.6.1.4.1.4458.1000.1.5.40.13 | DisplayString | read-only | Hub Site Synchronization GPS Longitude |
| STR winlink1000OduAirHssEWIndicator | 1.3.6.1.4.1.4458.1000.1.5.40.14 | DisplayString | read-only | Hub Site Synchronization GPS E/W Indicator |
| STR winlink1000OduAirHssNumSatellites | 1.3.6.1.4.1.4458.1000.1.5.40.15 | DisplayString | read-only | Hub Site Synchronization GPS Number of satellites |
| STR winlink1000OduAirHssAltitude | 1.3.6.1.4.1.4458.1000.1.5.40.16 | DisplayString | read-only | Hub Site Synchronization GPS Altitude |
| INT winlink1000OduAirHssRfpPhase | 1.3.6.1.4.1.4458.1000.1.5.40.17 | INTEGER | read-write | Hub Site Synchronization GPS RFP phase |
| INT winlink1000OduAirHssInterSiteSynchronizationMode | 1.3.6.1.4.1.4458.1000.1.5.40.18 | INTEGER | read-write | Inter-Site Synchronization Mode - independent / synchronized |
| INT winlink1000OduAirHssInterSiteSynchronizationAvailability | 1.3.6.1.4.1.4458.1000.1.5.40.19 | INTEGER | read-only | Inter-Site Synchronization Availability |
| INT winlink1000OduAirHssSatellitesSatSyncRequired | 1.3.6.1.4.1.4458.1000.1.5.40.20 | INTEGER | read-write | Satellites Synchronization Is Required |
| STR winlink1000OduAirHssDomainID | 1.3.6.1.4.1.4458.1000.1.5.40.21 | DisplayString | read-write | EHSS domain. Indentify set of CUs with same HSS synchronization |
| INT winlink1000OduAirHssSupportedSynchronizationProtocol | 1.3.6.1.4.1.4458.1000.1.5.40.22 | INTEGER | read-only | Supported Synchronization Protocols |
| INT winlink1000OduAirHssDesiredSynchronizationProtocol | 1.3.6.1.4.1.4458.1000.1.5.40.23 | INTEGER | read-write | Desired Synchronization Protocols |
| INT winlink1000OduAirHssDiscover | 1.3.6.1.4.1.4458.1000.1.5.40.24 | INTEGER | read-write | Initiate Discovery process of ODUs on the network. |
| INT winlink1000OduAirHssNumberOfDiscoveredODUs | 1.3.6.1.4.1.4458.1000.1.5.40.25 | INTEGER | read-only | Number OF Discovered ODUs in network. |
| winlink1000OduAirHssDiscoverTable | 1.3.6.1.4.1.4458.1000.1.5.40.26 | not-accessible | HSS Discover Table. | |
| winlink1000OduAirHssDiscoverEntry | 1.3.6.1.4.1.4458.1000.1.5.40.26.1 | not-accessible | ODU Discover Table entry. | |
| INT winlink1000OduAirHssDiscoverIndex | 1.3.6.1.4.1.4458.1000.1.5.40.26.1.1 | INTEGER | read-only | HSS Discover Table Index. |
| STR winlink1000OduAirHssDiscoverODUDescription | 1.3.6.1.4.1.4458.1000.1.5.40.26.1.2 | DisplayString | read-only | Hold ODU HSS status in compress format: Domain,IP,HSS Role,Hss support, Enabled HSS protocol,Sync Status, Location, IPv6. |
| INT winlink1000OduAirHssMasterSlaveCompatibility | 1.3.6.1.4.1.4458.1000.1.5.40.27 | INTEGER | read-only | EHSM version compatibility. Relevant to Ethernet HSS Clients only. |
| INT winlink1000OduAirHssNumberOfAssociatedCU | 1.3.6.1.4.1.4458.1000.1.5.40.28 | INTEGER | read-only | Number of associated Ethernet HSS Clients. Relevant to Ethernet HSS Masters only |
| winlink1000OduAirHssAssociatedCUTable | 1.3.6.1.4.1.4458.1000.1.5.40.29 | not-accessible | Associated Ethernet HSS Clients Table. Releant for Ethernet HSS Masters only. | |
| winlink1000OduAirHssAssociatedCUTableEntry | 1.3.6.1.4.1.4458.1000.1.5.40.29.1 | not-accessible | Associated Ethernet HSS Clients Table Entry. Releant for Ethernet HSS Masters only. | |
| INT winlink1000OduAirHssAssociatedCUIndex | 1.3.6.1.4.1.4458.1000.1.5.40.29.1.1 | INTEGER | read-only | Associated Ethernet HSS Clients Table Index. Releant for Ethernet HSS Masters only. |
| STR winlink1000OduAirHssAssociatedCUDescription | 1.3.6.1.4.1.4458.1000.1.5.40.29.1.2 | DisplayString | read-only | Holds Associated Ethernet HSS Clients Description in compress format: IP,Delay,Compatibility,Ethernet Speed, Ethernet Rx rate, IPv6 |
| INT winlink1000OduAirHssSyncStatusEth | 1.3.6.1.4.1.4458.1000.1.5.40.30 | INTEGER | read-only | Ethernet HSS Client Synchronization Level |
| INT winlink1000OduAirHssEthVLANTag | 1.3.6.1.4.1.4458.1000.1.5.40.31 | INTEGER | read-write | Ethernet HSS VLan Tag: The least significate decimal digit is the VLan Priority(0-6) and the rest of the digits represents VLan ID (2-4094) |
| IP winlink1000OduAirHssHSMIPAddress | 1.3.6.1.4.1.4458.1000.1.5.40.32 | IpAddress | read-only | HSMs IP address. Relevant for HSC synchronized over Ethernet. |
| INT winlink1000OduAirHssDelayToHSM | 1.3.6.1.4.1.4458.1000.1.5.40.33 | INTEGER | read-only | Delay in microseconds to HSM. Relevant for HSC synchronized over Ethernet. |
| INT winlink1000OduAirHssSyncAcquisitionSeconds | 1.3.6.1.4.1.4458.1000.1.5.40.34 | INTEGER | read-write | Accumulated quantity of seconds in clock acquisition while connected to current HSM |
| STR winlink1000OduAirHssHSMIPv6Address | 1.3.6.1.4.1.4458.1000.1.5.40.35 | DisplayString | read-only | HSMs IPv6 address. Relevant for HSC synchronized over Ethernet. |
| INT winlink1000OduAirLockRemote | 1.3.6.1.4.1.4458.1000.1.5.41 | INTEGER | read-write | This parameter enables locking the link with a specific ODU. The following values can be set: Unlock (default) - The ODU is not locked on a specific remote ODU. Unlock can only be performed when the link is not connected. Lock - The ODU is locked on a specific remote ODU. Lock can only be performed when the link is active. |
| INT winlink1000OduAirAntennaGain | 1.3.6.1.4.1.4458.1000.1.5.42 | INTEGER | read-write | Current Antenna Gain in 0.1 dBi resolution. User defined value for external antenna. Legal range: MinAntennaGain - Alarm. |
RFC description
Manages RADWIN WinLink1000 microwave radio link ODU (outdoor units) with configuration and administrative controls.
Start monitoring RADWIN point-to-point wireless transmission units with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.