Nortel-MsCarrier-MscPassport-AtmIispMIB

All MIBs › Nortel-MsCarrier-MscPassport-AtmIispMIB

Category: Nortel MsCarrier MscPassport

Description: Defines SNMP objects for ATM IISP (Interim Inter-Switch Signaling Protocol) on Nortel MsCarrier MscPassport switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Nortel-MsCarrier-MscPassport-AtmIispMIB?

This is a vendor-specific MIB from Nortel for the MSCarrier/MSC Passport ATM switching platform, covering ATM Interim Inter-Switch Signaling Protocol (IISP) used between ATM switches that do not run full PNNI. It exposes provisioning objects for IISP interfaces, including row-status tables for IISP components, a provisioning table capturing protocol version and network-side designation, and soft-PVC retry timing. Its monitoring value lies in confirming operational/administrative status of IISP signaling links via row status and validating correct IISP version and side configuration, misconfiguration of which prevents signaling adjacency and call setup. It is a Nortel-proprietary implementation of the ATM Forum's IISP signaling specification, so its correctness depends on that inter-switch signaling standard. It is deployed on legacy Nortel MSC Passport ATM switches in carrier ATM backbones using IISP for switch-to-switch signaling. Engineers can download the Nortel-MsCarrier-MscPassport-AtmIispMIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Nortel-MsCarrier-MscPassport-AtmIispMIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nortel MSC Passport ATM switch

Monitoring Examples

An operator would poll mscAtmIfIispRowStatusTable/mscAtmIfIispRowStatusEntry to confirm mscAtmIfIispRowStatus is active for each configured interface, and check mscAtmIfIispProvTable entries for mscAtmIfIispVersion and mscAtmIfIispSide to verify matching settings between adjacent switches. A mismatched mscAtmIfIispSide or inactive row status would explain a failure to establish IISP signaling adjacency and an inability to set up ATM PVCs/SVCs across that link.

What Can Be Monitored

IISP interface row/administrative status
IISP protocol version
IISP network/user side configuration
soft-PVC retry period

Imported Objects

From Nortel-MsCarrier-MscPassport-AtmCoreMIB

mscAtmIf	OBJECT-IDENTITY
mscAtmIfIndex	OBJECT-TYPE
mscAtmIfVpt	OBJECT-IDENTITY
mscAtmIfVptIndex	OBJECT-TYPE

From Nortel-MsCarrier-MscPassport-StandardTextualConventionsMIB

Counter32
DisplayString
Gauge32
Integer32
RowStatus
StorageType
Unsigned32

From Nortel-MsCarrier-MscPassport-TextualConventionsMIB

AsciiStringIndex
Hex
HexString
NonReplicated

From Nortel-MsCarrier-MscPassport-UsefulDefinitionsMIB

mscPassportMIBs

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
mscAtmIfIisp	1.3.6.1.4.1.562.36.2.1.114.7
mscAtmIfIispRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.7.1		not-accessible	This entry controls the addition and deletion of mscAtmIfIisp components.
mscAtmIfIispRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.7.1.1		not-accessible	A single entry in the table represents a single mscAtmIfIisp component.
ROW mscAtmIfIispRowStatus	1.3.6.1.4.1.562.36.2.1.114.7.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfIisp components. These components can be added and deleted.
STR mscAtmIfIispComponentName	1.3.6.1.4.1.562.36.2.1.114.7.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfIispStorageType	1.3.6.1.4.1.562.36.2.1.114.7.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfIisp tables.
NON mscAtmIfIispIndex	1.3.6.1.4.1.562.36.2.1.114.7.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscAtmIfIisp tables.
mscAtmIfIispSig	1.3.6.1.4.1.562.36.2.1.114.7.3
mscAtmIfIispSigRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.7.3.1		not-accessible	This entry controls the addition and deletion of mscAtmIfIispSig components.
mscAtmIfIispSigRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.7.3.1.1		not-accessible	A single entry in the table represents a single mscAtmIfIispSig component.
ROW mscAtmIfIispSigRowStatus	1.3.6.1.4.1.562.36.2.1.114.7.3.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mscAtmIfIispSig components. These components cannot be added nor deleted.
STR mscAtmIfIispSigComponentName	1.3.6.1.4.1.562.36.2.1.114.7.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfIispSigStorageType	1.3.6.1.4.1.562.36.2.1.114.7.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfIispSig tables.
NON mscAtmIfIispSigIndex	1.3.6.1.4.1.562.36.2.1.114.7.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscAtmIfIispSig tables.
mscAtmIfIispSigVcd	1.3.6.1.4.1.562.36.2.1.114.7.3.2
mscAtmIfIispSigVcdRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.7.3.2.1		not-accessible	This entry controls the addition and deletion of mscAtmIfIispSigVcd components.
mscAtmIfIispSigVcdRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.7.3.2.1.1		not-accessible	A single entry in the table represents a single mscAtmIfIispSigVcd component.
ROW mscAtmIfIispSigVcdRowStatus	1.3.6.1.4.1.562.36.2.1.114.7.3.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfIispSigVcd components. These components can be added and deleted.
STR mscAtmIfIispSigVcdComponentName	1.3.6.1.4.1.562.36.2.1.114.7.3.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfIispSigVcdStorageType	1.3.6.1.4.1.562.36.2.1.114.7.3.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfIispSigVcd tables.
NON mscAtmIfIispSigVcdIndex	1.3.6.1.4.1.562.36.2.1.114.7.3.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscAtmIfIispSigVcd tables.
mscAtmIfIispSigVcdProvTable	1.3.6.1.4.1.562.36.2.1.114.7.3.2.10		not-accessible	This group contains the provisionable traffic attributes for a control channel.
mscAtmIfIispSigVcdProvEntry	1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1		not-accessible	An entry in the mscAtmIfIispSigVcdProvTable.
INT mscAtmIfIispSigVcdTrafficDescType	1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1.1	INTEGER	read-write	This attribute specifies the type of traffic management which is applied to both the transmit and receive direction of this connection as defined in the ATM Forum. The trafficDescType determines the number and meaning of the parameters in the trafficDescParm attribute.
INT mscAtmIfIispSigVcdAtmServiceCategory	1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1.3	INTEGER	read-write	This attribute specifies the ATM service category for both directions of the connection. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection.
U32 mscAtmIfIispSigVcdWeight	1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1.4	Unsigned32	read-write	This attribute specifies an override for the weight of this unshaped connection. This attribute is ignored for shaped connections, for ABR connections, for connections on a CQC-based ATM FP and basic VPTs. When the value is set to sameAsCa, the weight is determined by the weight policy attribute under the CA service category component for all but standard VPT VCCs. For standard VPT VCCs, the weight is determined by the VCC's service category, when the value is set to sameAsCa. When this attribute is set to a value from 1 to 4095, that value is used for the weight policy of this connection relative to other connections. For all but standard VPT VCCs, weight policy determines the proportion of transit cell opportunities which are allocated to this connection, compared to other connections in the same service category. For standard VPT VCCs, weight policy determines the proportion of transmit cell opportunities which are allocated to this connection, compared to other connections associated with the VPT. When the value is set to upToQueueLimit, the weight policy is limited only by the txQueueLimit. VALUES ( 0 = upToQueueLimit 65535 = sameAsCa )
INT mscAtmIfIispSigVcdQosClass	1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1.21	INTEGER	read-write	This attribute specifies the quality of service for both the forward and backward direction for this connection. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters.
INT mscAtmIfIispSigVcdTrafficShaping	1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1.50	INTEGER	read-write	This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. When sameAsCa is selected, traffic shaping for this connection is based on the trafficShaping attribute of the connection's service category component under the AtmIf CA. If the service category has traffic shaping enabled, then traffic shaping is enabled for the connection. Note that enabling traffic shaping may have no effect under certain cases. These cases are listed in the description of the trafficShaping operational attribute, which is under the Vcc Tm and Vpc Tm components. When disabled is selected, traffic shaping for this connection is disabled.
INT mscAtmIfIispSigVcdUnshapedTransmitQueueing	1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1.60	INTEGER	read-write	This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this connection if it is unshaped. Refer to the unshapedTransmitQueueing attribute under the AtmIf CA service category subcomponent for more details on the meaning of this attribute. When this attribute is set to sameAsCa, the transmit queueing method for the connection is based on the unshapedTransmitQueueing attribute of the connection's service category component under the ConnectionAdministrator. When this attribute is set to common, transmit traffic on this unshaped connection is destined for the common queue. The value sameAsInterface is for migration from previous software releases, but should no longer be used
INT mscAtmIfIispSigVcdUsageParameterControl	1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1.70	INTEGER	read-write	This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface. When sameAsCa is selected, UPC for the connection is based on the usageParameterControl attribute of the connection's service category component under the ConnectionAdministrator. If the service category has UPC enabled, then UPC is enabled for the connection. Note that enabling UPC may have no effect under certain cases. These cases are listed in the description of the usageParameterControl operational attribute, which is under the Vcc Tm or Vpc Tm component. When disabled is selected, UPC for this connection is disabled. The value sameAsInterface is for migration from previous software releases, but should no longer be used
mscAtmIfIispSigVcdTdpTable	1.3.6.1.4.1.562.36.2.1.114.7.3.2.387		not-accessible	This attribute is a vector of five traffic parameters whose meanings are defined by the trafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When trafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When trafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For trafficDescType 3 the traffic is shaped at the next rate less than the PCR. For trafficDescType 6, 7, and 8, the traffic is shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic is shaped at the next rate above the PCR.
mscAtmIfIispSigVcdTdpEntry	1.3.6.1.4.1.562.36.2.1.114.7.3.2.387.1		not-accessible	An entry in the mscAtmIfIispSigVcdTdpTable.
I32 mscAtmIfIispSigVcdTdpIndex	1.3.6.1.4.1.562.36.2.1.114.7.3.2.387.1.1	Integer32	not-accessible	This variable represents the mscAtmIfIispSigVcdTdpTable specific index for the mscAtmIfIispSigVcdTdpTable.
U32 mscAtmIfIispSigVcdTdpValue	1.3.6.1.4.1.562.36.2.1.114.7.3.2.387.1.2	Unsigned32	read-write	This variable represents an individual value for the mscAtmIfIispSigVcdTdpTable.
mscAtmIfIispSigProvTable	1.3.6.1.4.1.562.36.2.1.114.7.3.10		not-accessible	This attribute group contains the provisionable attributes for the Signalling component.
mscAtmIfIispSigProvEntry	1.3.6.1.4.1.562.36.2.1.114.7.3.10.1		not-accessible	An entry in the mscAtmIfIispSigProvTable.
U32 mscAtmIfIispSigVci	1.3.6.1.4.1.562.36.2.1.114.7.3.10.1.1	Unsigned32	read-write	This attribute specifies the signalling channel number.
INT mscAtmIfIispSigAddressConversion	1.3.6.1.4.1.562.36.2.1.114.7.3.10.1.2	INTEGER	read-write	This attribute specifies the address conversion on the outgoing signalling PDUs. The options are none, nativeE164, or nsap. The none option is the default and if this option is chosen then nothing is done to the address information element (IE) in the outgoing signalling message. If nativeE164 option is chosen, then only NSAP encapsulated E.164 addresses with zeros in the ESI are converted to native E.164 format in the outgoing signalling message. If the NSAP address is not encapsulated E.164 or the ESI field is not zeros and the nativeE164 option is chosen, then the call is cleared. If the nsap option is chosen, then native E.164 addresses are converted to NSAP E.164 with zeros in the ESI field; otherwise the address is in NSAP format and is not changed.
INT mscAtmIfIispSigOperatingMode	1.3.6.1.4.1.562.36.2.1.114.7.3.10.1.3	INTEGER	read-write	This attribute specifies the operating mode of the signaling channel. provisionedOnly indicates that only SPVCs and SPVPs are supported on the interface and SVCs are not supported. This value is permitted only on UNI interfaces. normal indicates that SVCs, SPVCs, and SPVPs are supported on the interface.
mscAtmIfIispSigStateTable	1.3.6.1.4.1.562.36.2.1.114.7.3.11		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
mscAtmIfIispSigStateEntry	1.3.6.1.4.1.562.36.2.1.114.7.3.11.1		not-accessible	An entry in the mscAtmIfIispSigStateTable.
INT mscAtmIfIispSigAdminState	1.3.6.1.4.1.562.36.2.1.114.7.3.11.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT mscAtmIfIispSigOperationalState	1.3.6.1.4.1.562.36.2.1.114.7.3.11.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT mscAtmIfIispSigUsageState	1.3.6.1.4.1.562.36.2.1.114.7.3.11.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
mscAtmIfIispSigOperTable	1.3.6.1.4.1.562.36.2.1.114.7.3.12		not-accessible	This attribute contains the operational attributes for the AtmSignalling component.
mscAtmIfIispSigOperEntry	1.3.6.1.4.1.562.36.2.1.114.7.3.12.1		not-accessible	An entry in the mscAtmIfIispSigOperTable.
U32 mscAtmIfIispSigLastTxCauseCode	1.3.6.1.4.1.562.36.2.1.114.7.3.12.1.1	Unsigned32	read-only	This attribute indicates the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX mscAtmIfIispSigLastTxDiagCode	1.3.6.1.4.1.562.36.2.1.114.7.3.12.1.2	Hex	read-only	This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
U32 mscAtmIfIispSigLastRxCauseCode	1.3.6.1.4.1.562.36.2.1.114.7.3.12.1.3	Unsigned32	read-only	This attribute contains the cause code in the last received signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX mscAtmIfIispSigLastRxDiagCode	1.3.6.1.4.1.562.36.2.1.114.7.3.12.1.4	Hex	read-only	This attribute contains the diagnostic code in the last received signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
mscAtmIfIispSigStatsTable	1.3.6.1.4.1.562.36.2.1.114.7.3.13		not-accessible	This attribute group contains the statistics associated with the AtmSignalling component.
mscAtmIfIispSigStatsEntry	1.3.6.1.4.1.562.36.2.1.114.7.3.13.1		not-accessible	An entry in the mscAtmIfIispSigStatsTable.
C32 mscAtmIfIispSigCurrentConnections	1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.1	Counter32	read-only	This attribute indicates the total number of currently active connections.
G32 mscAtmIfIispSigPeakConnections	1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.2	Gauge32	read-only	This attribute indicates the high water mark of active point-to- point and point-to-multipoint connections.
C32 mscAtmIfIispSigSuccessfulConnections	1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.3	Counter32	read-only	This attribute counts the total number of switched point-to- point and point-to-multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 mscAtmIfIispSigFailedConnections	1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.4	Counter32	read-only	This attribute counts the total number of switched connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
C32 mscAtmIfIispSigTxPdus	1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.5	Counter32	read-only	This attribute counts the number of transmitted signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
C32 mscAtmIfIispSigRxPdus	1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.6	Counter32	read-only	This attribute counts the number of received signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
G32 mscAtmIfIispSigCurrentPmpConnections	1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.7	Gauge32	read-only	This attribute indicates the number of currently active point-to- multipoint connections.
G32 mscAtmIfIispSigPeakPmpConnections	1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.8	Gauge32	read-only	This attribute indicates the high water mark of active point-to- multipoint connections.
C32 mscAtmIfIispSigSuccessfulPmpConnections	1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.9	Counter32	read-only	This attribute counts the total number of switched point-to- multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 mscAtmIfIispSigFailedPmpConnections	1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.10	Counter32	read-only	This attribute counts the number of switched point-to- multipoint connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
G32 mscAtmIfIispSigNewCurrentConnections	1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.11	Gauge32	read-only	This attribute indicates the total number of currently active point-to- point and point-to-multipoint connections.
mscAtmIfIispAddr	1.3.6.1.4.1.562.36.2.1.114.7.4
mscAtmIfIispAddrRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.7.4.1		not-accessible	This entry controls the addition and deletion of mscAtmIfIispAddr components.
mscAtmIfIispAddrRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.7.4.1.1		not-accessible	A single entry in the table represents a single mscAtmIfIispAddr component.
ROW mscAtmIfIispAddrRowStatus	1.3.6.1.4.1.562.36.2.1.114.7.4.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfIispAddr components. These components can be added and deleted.
STR mscAtmIfIispAddrComponentName	1.3.6.1.4.1.562.36.2.1.114.7.4.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfIispAddrStorageType	1.3.6.1.4.1.562.36.2.1.114.7.4.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfIispAddr tables.
STR mscAtmIfIispAddrAddressIndex	1.3.6.1.4.1.562.36.2.1.114.7.4.1.1.10	AsciiStringIndex	not-accessible	This variable represents an index for the mscAtmIfIispAddr tables.
INT mscAtmIfIispAddrAddressTypeIndex	1.3.6.1.4.1.562.36.2.1.114.7.4.1.1.11	INTEGER	not-accessible	This variable represents an index for the mscAtmIfIispAddr tables.
mscAtmIfIispAddrTermSP	1.3.6.1.4.1.562.36.2.1.114.7.4.2
mscAtmIfIispAddrTermSPRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.7.4.2.1		not-accessible	This entry controls the addition and deletion of mscAtmIfIispAddrTermSP components.
mscAtmIfIispAddrTermSPRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.7.4.2.1.1		not-accessible	A single entry in the table represents a single mscAtmIfIispAddrTermSP component.
ROW mscAtmIfIispAddrTermSPRowStatus	1.3.6.1.4.1.562.36.2.1.114.7.4.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfIispAddrTermSP components. These components can be added and deleted.
STR mscAtmIfIispAddrTermSPComponentName	1.3.6.1.4.1.562.36.2.1.114.7.4.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfIispAddrTermSPStorageType	1.3.6.1.4.1.562.36.2.1.114.7.4.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfIispAddrTermSP tables.
NON mscAtmIfIispAddrTermSPIndex	1.3.6.1.4.1.562.36.2.1.114.7.4.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscAtmIfIispAddrTermSP tables.
mscAtmIfIispAddrPnniInfo	1.3.6.1.4.1.562.36.2.1.114.7.4.3
mscAtmIfIispAddrPnniInfoRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.7.4.3.1		not-accessible	This entry controls the addition and deletion of mscAtmIfIispAddrPnniInfo components.
mscAtmIfIispAddrPnniInfoRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.7.4.3.1.1		not-accessible	A single entry in the table represents a single mscAtmIfIispAddrPnniInfo component.
ROW mscAtmIfIispAddrPnniInfoRowStatus	1.3.6.1.4.1.562.36.2.1.114.7.4.3.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfIispAddrPnniInfo components. These components can be added and deleted.
STR mscAtmIfIispAddrPnniInfoComponentName	1.3.6.1.4.1.562.36.2.1.114.7.4.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfIispAddrPnniInfoStorageType	1.3.6.1.4.1.562.36.2.1.114.7.4.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfIispAddrPnniInfo tables.
NON mscAtmIfIispAddrPnniInfoIndex	1.3.6.1.4.1.562.36.2.1.114.7.4.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscAtmIfIispAddrPnniInfo tables.
mscAtmIfIispAddrPnniInfoProvTable	1.3.6.1.4.1.562.36.2.1.114.7.4.3.10		not-accessible	This attribute group contains the provisioned attributes relating to PNNI for a PnniInfo component.
mscAtmIfIispAddrPnniInfoProvEntry	1.3.6.1.4.1.562.36.2.1.114.7.4.3.10.1		not-accessible	An entry in the mscAtmIfIispAddrPnniInfoProvTable.
INT mscAtmIfIispAddrPnniInfoScope	1.3.6.1.4.1.562.36.2.1.114.7.4.3.10.1.1	INTEGER	read-write	This attribute specifies the scope of the ATM address, which is the highest level up to which this address will be advertised in the PNNI hierarchy. The scope must be set to a value numerically less than or equal to the level of the lowest level peer group containing this node. Setting the scope to 0 will cause the address to be advertised globally within this PNNI routing domain.
INT mscAtmIfIispAddrPnniInfoReachability	1.3.6.1.4.1.562.36.2.1.114.7.4.3.10.1.2	INTEGER	read-write	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
mscAtmIfIispAddrOperTable	1.3.6.1.4.1.562.36.2.1.114.7.4.10		not-accessible	This attribute group contains the operational attributes for the Address component.
mscAtmIfIispAddrOperEntry	1.3.6.1.4.1.562.36.2.1.114.7.4.10.1		not-accessible	An entry in the mscAtmIfIispAddrOperTable.
INT mscAtmIfIispAddrScope	1.3.6.1.4.1.562.36.2.1.114.7.4.10.1.1	INTEGER	read-only	This attribute indicates the scope of the ATM address, which is the highest level to which this address will be advertised in the PNNI hierarchy. If no PnniInfo subcomponent has been provisioned, then the scope will default to the level of this node in the PNNI hierarchy. If this node does not participate in a PNNI hierarchy, then this attribute will have the value of -1.
INT mscAtmIfIispAddrReachability	1.3.6.1.4.1.562.36.2.1.114.7.4.10.1.2	INTEGER	read-only	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
mscAtmIfIispCallingAScr	1.3.6.1.4.1.562.36.2.1.114.7.5
mscAtmIfIispCallingAScrRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.7.5.1		not-accessible	This entry controls the addition and deletion of mscAtmIfIispCallingAScr components.
mscAtmIfIispCallingAScrRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.7.5.1.1		not-accessible	A single entry in the table represents a single mscAtmIfIispCallingAScr component.
ROW mscAtmIfIispCallingAScrRowStatus	1.3.6.1.4.1.562.36.2.1.114.7.5.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfIispCallingAScr components. These components can be added and deleted.
STR mscAtmIfIispCallingAScrComponentName	1.3.6.1.4.1.562.36.2.1.114.7.5.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfIispCallingAScrStorageType	1.3.6.1.4.1.562.36.2.1.114.7.5.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfIispCallingAScr tables.
NON mscAtmIfIispCallingAScrIndex	1.3.6.1.4.1.562.36.2.1.114.7.5.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscAtmIfIispCallingAScr tables.
mscAtmIfIispCallingAScrAddr	1.3.6.1.4.1.562.36.2.1.114.7.5.2
mscAtmIfIispCallingAScrAddrRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.7.5.2.1		not-accessible	This entry controls the addition and deletion of mscAtmIfIispCallingAScrAddr components.
mscAtmIfIispCallingAScrAddrRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.7.5.2.1.1		not-accessible	A single entry in the table represents a single mscAtmIfIispCallingAScrAddr component.
ROW mscAtmIfIispCallingAScrAddrRowStatus	1.3.6.1.4.1.562.36.2.1.114.7.5.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfIispCallingAScrAddr components. These components can be added and deleted.
STR mscAtmIfIispCallingAScrAddrComponentName	1.3.6.1.4.1.562.36.2.1.114.7.5.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfIispCallingAScrAddrStorageType	1.3.6.1.4.1.562.36.2.1.114.7.5.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfIispCallingAScrAddr tables.
STR mscAtmIfIispCallingAScrAddrAddressIndex	1.3.6.1.4.1.562.36.2.1.114.7.5.2.1.1.10	AsciiStringIndex	not-accessible	This variable represents an index for the mscAtmIfIispCallingAScrAddr tables.
INT mscAtmIfIispCallingAScrAddrAddressActionIndex	1.3.6.1.4.1.562.36.2.1.114.7.5.2.1.1.11	INTEGER	not-accessible	This variable represents an index for the mscAtmIfIispCallingAScrAddr tables.
mscAtmIfIispCallingAScrProvTable	1.3.6.1.4.1.562.36.2.1.114.7.5.10		not-accessible	This attribute group contains the provisionable attributes for the CallingAScr component.
mscAtmIfIispCallingAScrProvEntry	1.3.6.1.4.1.562.36.2.1.114.7.5.10.1		not-accessible	An entry in the mscAtmIfIispCallingAScrProvTable.
INT mscAtmIfIispCallingAScrAdminStatus	1.3.6.1.4.1.562.36.2.1.114.7.5.10.1.1	INTEGER	read-write	This attribute specifies whether the calling address screening feature is enabled or disabled. If enabled, incoming SVC calls are screened against provisioned addresses. If enabled and the calling address in the ATM SVC call request is provisioned to be accepted, the call is accepted or rejected according to the action specified for that address. If the value is enabled, and the calling address in the address request is not provisioned, the call is rejected If the value is disabled, no calling address screening is performed.
STR mscAtmIfIispCallingAScrDefaultInsertionAddress	1.3.6.1.4.1.562.36.2.1.114.7.5.10.1.2	HexString	read-write	This attribute specifies the address to be inserted into the SVC connection request if adminStatus is enabled and the connection request does not contain a calling address. If the adminStatus attribute is enabled and this attribute is empty, all incoming SVC calls which do not contain a calling address are rejected.
mscAtmIfIispCallingAScrStatTable	1.3.6.1.4.1.562.36.2.1.114.7.5.11		not-accessible	This attribute group contains statistics related to the incoming SVC call requests received while the adminStatus attribute is set to enabled.
mscAtmIfIispCallingAScrStatEntry	1.3.6.1.4.1.562.36.2.1.114.7.5.11.1		not-accessible	An entry in the mscAtmIfIispCallingAScrStatTable.
C32 mscAtmIfIispCallingAScrAcceptedCalls	1.3.6.1.4.1.562.36.2.1.114.7.5.11.1.1	Counter32	read-only	This attribute counts the incoming SVC calls which were accepted because the address specified in the call request matched a provisioned ATM address and the associated action was accept. When the counter exceeds the maximum, it wraps to 0.
C32 mscAtmIfIispCallingAScrRejectedCalls	1.3.6.1.4.1.562.36.2.1.114.7.5.11.1.2	Counter32	read-only	This attribute counts the incoming SVC calls which were rejected because the address specified in the call request matched a provisioned ATM address, but the associated action was reject. When the counter exceeds the maximum, it wraps to 0.
C32 mscAtmIfIispCallingAScrUnmatchedCalls	1.3.6.1.4.1.562.36.2.1.114.7.5.11.1.3	Counter32	read-only	This attribute counts the incoming SVC calls which were rejected because none of the provisioned ATM addresses matched the applicable address in the incoming SVC call request. When the counter exceeds the maximum, it wraps to 0.
mscAtmIfIispCalledAScr	1.3.6.1.4.1.562.36.2.1.114.7.6
mscAtmIfIispCalledAScrRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.7.6.1		not-accessible	This entry controls the addition and deletion of mscAtmIfIispCalledAScr components.
mscAtmIfIispCalledAScrRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.7.6.1.1		not-accessible	A single entry in the table represents a single mscAtmIfIispCalledAScr component.
ROW mscAtmIfIispCalledAScrRowStatus	1.3.6.1.4.1.562.36.2.1.114.7.6.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfIispCalledAScr components. These components can be added and deleted.
STR mscAtmIfIispCalledAScrComponentName	1.3.6.1.4.1.562.36.2.1.114.7.6.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfIispCalledAScrStorageType	1.3.6.1.4.1.562.36.2.1.114.7.6.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfIispCalledAScr tables.
NON mscAtmIfIispCalledAScrIndex	1.3.6.1.4.1.562.36.2.1.114.7.6.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscAtmIfIispCalledAScr tables.
mscAtmIfIispCalledAScrAddr	1.3.6.1.4.1.562.36.2.1.114.7.6.2
mscAtmIfIispCalledAScrAddrRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.7.6.2.1		not-accessible	This entry controls the addition and deletion of mscAtmIfIispCalledAScrAddr components.
mscAtmIfIispCalledAScrAddrRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.7.6.2.1.1		not-accessible	A single entry in the table represents a single mscAtmIfIispCalledAScrAddr component.
ROW mscAtmIfIispCalledAScrAddrRowStatus	1.3.6.1.4.1.562.36.2.1.114.7.6.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfIispCalledAScrAddr components. These components can be added and deleted.
STR mscAtmIfIispCalledAScrAddrComponentName	1.3.6.1.4.1.562.36.2.1.114.7.6.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfIispCalledAScrAddrStorageType	1.3.6.1.4.1.562.36.2.1.114.7.6.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfIispCalledAScrAddr tables.
STR mscAtmIfIispCalledAScrAddrAddressIndex	1.3.6.1.4.1.562.36.2.1.114.7.6.2.1.1.10	AsciiStringIndex	not-accessible	This variable represents an index for the mscAtmIfIispCalledAScrAddr tables.
INT mscAtmIfIispCalledAScrAddrAddressActionIndex	1.3.6.1.4.1.562.36.2.1.114.7.6.2.1.1.11	INTEGER	not-accessible	This variable represents an index for the mscAtmIfIispCalledAScrAddr tables.
mscAtmIfIispCalledAScrProvTable	1.3.6.1.4.1.562.36.2.1.114.7.6.10		not-accessible	This attribute group contains the provisionable attributes for the CalledAScr component.
mscAtmIfIispCalledAScrProvEntry	1.3.6.1.4.1.562.36.2.1.114.7.6.10.1		not-accessible	An entry in the mscAtmIfIispCalledAScrProvTable.
INT mscAtmIfIispCalledAScrAdminStatus	1.3.6.1.4.1.562.36.2.1.114.7.6.10.1.1	INTEGER	read-write	This attribute specifies whether the called address screening feature is enabled or disabled. If the value is enabled, incoming SVC calls will be screened against provisioned called addresses. If the value is enabled and the called address in the ATM SVC call request has been provisioned, the call is accepted or rejected according to the action specified for that address. If the value is enabled and the called address in the call request is not provisioned, the call is rejected. If the value is disabled, no called address screening is performed.
mscAtmIfIispCalledAScrStatTable	1.3.6.1.4.1.562.36.2.1.114.7.6.11		not-accessible	This attribute group contains statistics related to the incoming SVC call requests received while the adminStatus attribute is set to enabled.
mscAtmIfIispCalledAScrStatEntry	1.3.6.1.4.1.562.36.2.1.114.7.6.11.1		not-accessible	An entry in the mscAtmIfIispCalledAScrStatTable.
C32 mscAtmIfIispCalledAScrAcceptedCalls	1.3.6.1.4.1.562.36.2.1.114.7.6.11.1.1	Counter32	read-only	This attribute counts the incoming SVC calls which were accepted because the address specified in the call request matched a provisioned ATM address and the associated action was accept. When the counter exceeds the maximum, it wraps to 0.
C32 mscAtmIfIispCalledAScrRejectedCalls	1.3.6.1.4.1.562.36.2.1.114.7.6.11.1.2	Counter32	read-only	This attribute counts the incoming SVC calls which were rejected because the address specified in the call request matched a provisioned ATM address, but the associated action was reject. When the counter exceeds the maximum, it wraps to 0.
C32 mscAtmIfIispCalledAScrUnmatchedCalls	1.3.6.1.4.1.562.36.2.1.114.7.6.11.1.3	Counter32	read-only	This attribute counts the incoming SVC calls which were rejected because none of the provisioned ATM addresses matched the applicable address in the incoming SVC call request. When the counter exceeds the maximum, it wraps to 0.
mscAtmIfIispProvTable	1.3.6.1.4.1.562.36.2.1.114.7.10		not-accessible	This group contains the provisionable attributes for the Iisp component.
mscAtmIfIispProvEntry	1.3.6.1.4.1.562.36.2.1.114.7.10.1		not-accessible	An entry in the mscAtmIfIispProvTable.
INT mscAtmIfIispVersion	1.3.6.1.4.1.562.36.2.1.114.7.10.1.1	INTEGER	read-write	This attribute indicates which specification the IISP interface complies with. The options are iisp10Sig30 which refers to IISP version 1.0 with 3.0 signalling and iisp10Sig31 which refers to IISP version 1.0 with 3.1 signalling. If this attribute is changed, all switched Vcc components in this interface are cleared due to the fact that the two versions are incompatible.
INT mscAtmIfIispSide	1.3.6.1.4.1.562.36.2.1.114.7.10.1.2	INTEGER	read-write	This attribute indicates which side the interface is, user or network.
U32 mscAtmIfIispSoftPvcRetryPeriod	1.3.6.1.4.1.562.36.2.1.114.7.10.1.3	Unsigned32	read-write	This attribute specifies the time to wait between call set up retries. The resolution is to the nearest 10 seconds. This attribute has been obsoleted and is replaced by the softPvpAndPvcRetryPeriod attribute.
U32 mscAtmIfIispSoftPvpAndPvcRetryPeriod	1.3.6.1.4.1.562.36.2.1.114.7.10.1.4	Unsigned32	read-write	This attribute specifies the time to wait between soft PVP or soft PVC call setup retries. The resolution is to the nearest 10 seconds.
U32 mscAtmIfIispSoftPvpAndPvcHoldOffTime	1.3.6.1.4.1.562.36.2.1.114.7.10.1.5	Unsigned32	read-write	This attribute specifies how long to hold off retries following a release or the connection. The resolution is to the nearest 50 ms.
mscAtmIfIispAcctOptTable	1.3.6.1.4.1.562.36.2.1.114.7.11		not-accessible	This group contains the provisionable attributes for accounting.
mscAtmIfIispAcctOptEntry	1.3.6.1.4.1.562.36.2.1.114.7.11.1		not-accessible	An entry in the mscAtmIfIispAcctOptTable.
OCT mscAtmIfIispAccountCollection	1.3.6.1.4.1.562.36.2.1.114.7.11.1.1	OCTET STRING	read-write	This attribute is used to turn accounting on or off for SVC and SPVC connections. It also specifies the reason(s) for which accounting data is collected: billing, test, study, audit, or force. If the set of reasons is not empty then accounting records will be generated by this interface in the following situations: - on a TODA changeover if TODA is enabled; - every 12 hours (per connection) if TODA is disabled; - on every call clear (a call record with final cell counts). If none of the reasons is present, then accounting will be suppressed. The reason for collection is recorded in the accounting record, in the attribute callingCollectReason or calledCollectReason as appropriate. Description of bits: bill(0) test(1) study(2) audit(3) force(4)
INT mscAtmIfIispAccountConnectionType	1.3.6.1.4.1.562.36.2.1.114.7.11.1.2	INTEGER	read-write	This attribute specifies whether accounting records generated by this interface should be marked as originating, terminating or intermediate. This attribute, in combination with the direction of the call, determines the value of attribute connPointType of the accounting record and may be used by downstream accounting processes to correlate the records. If the value is origTerm then records generated for incoming calls will be marked as originating and records generated for outgoing calls will be marked as terminating. If the value is intermediate then records generated for all calls will be marked as intermediate.
U32 mscAtmIfIispAccountClass	1.3.6.1.4.1.562.36.2.1.114.7.11.1.3	Unsigned32	read-write	This attribute specifies the accounting class associated with the interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingServiceType or calledServiceType as appropriate.
U32 mscAtmIfIispServiceExchange	1.3.6.1.4.1.562.36.2.1.114.7.11.1.4	Unsigned32	read-write	This attribute specifies the data service exchange associated with this interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingDse or calledDse as appropriate.
mscAtmIfVptIisp	1.3.6.1.4.1.562.36.2.1.114.9.6
mscAtmIfVptIispRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.9.6.1		not-accessible	This entry controls the addition and deletion of mscAtmIfVptIisp components.
mscAtmIfVptIispRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.1.1		not-accessible	A single entry in the table represents a single mscAtmIfVptIisp component.
ROW mscAtmIfVptIispRowStatus	1.3.6.1.4.1.562.36.2.1.114.9.6.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfVptIisp components. These components can be added and deleted.
STR mscAtmIfVptIispComponentName	1.3.6.1.4.1.562.36.2.1.114.9.6.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfVptIispStorageType	1.3.6.1.4.1.562.36.2.1.114.9.6.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfVptIisp tables.
NON mscAtmIfVptIispIndex	1.3.6.1.4.1.562.36.2.1.114.9.6.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscAtmIfVptIisp tables.
mscAtmIfVptIispSig	1.3.6.1.4.1.562.36.2.1.114.9.6.3
mscAtmIfVptIispSigRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.9.6.3.1		not-accessible	This entry controls the addition and deletion of mscAtmIfVptIispSig components.
mscAtmIfVptIispSigRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.3.1.1		not-accessible	A single entry in the table represents a single mscAtmIfVptIispSig component.
ROW mscAtmIfVptIispSigRowStatus	1.3.6.1.4.1.562.36.2.1.114.9.6.3.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mscAtmIfVptIispSig components. These components cannot be added nor deleted.
STR mscAtmIfVptIispSigComponentName	1.3.6.1.4.1.562.36.2.1.114.9.6.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfVptIispSigStorageType	1.3.6.1.4.1.562.36.2.1.114.9.6.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfVptIispSig tables.
NON mscAtmIfVptIispSigIndex	1.3.6.1.4.1.562.36.2.1.114.9.6.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscAtmIfVptIispSig tables.
mscAtmIfVptIispSigVcd	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2
mscAtmIfVptIispSigVcdRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.1		not-accessible	This entry controls the addition and deletion of mscAtmIfVptIispSigVcd components.
mscAtmIfVptIispSigVcdRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.1.1		not-accessible	A single entry in the table represents a single mscAtmIfVptIispSigVcd component.
ROW mscAtmIfVptIispSigVcdRowStatus	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfVptIispSigVcd components. These components can be added and deleted.
STR mscAtmIfVptIispSigVcdComponentName	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfVptIispSigVcdStorageType	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfVptIispSigVcd tables.
NON mscAtmIfVptIispSigVcdIndex	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscAtmIfVptIispSigVcd tables.
mscAtmIfVptIispSigVcdProvTable	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10		not-accessible	This group contains the provisionable traffic attributes for a control channel.
mscAtmIfVptIispSigVcdProvEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1		not-accessible	An entry in the mscAtmIfVptIispSigVcdProvTable.
INT mscAtmIfVptIispSigVcdTrafficDescType	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1.1	INTEGER	read-write	This attribute specifies the type of traffic management which is applied to both the transmit and receive direction of this connection as defined in the ATM Forum. The trafficDescType determines the number and meaning of the parameters in the trafficDescParm attribute.
INT mscAtmIfVptIispSigVcdAtmServiceCategory	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1.3	INTEGER	read-write	This attribute specifies the ATM service category for both directions of the connection. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection.
U32 mscAtmIfVptIispSigVcdWeight	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1.4	Unsigned32	read-write	This attribute specifies an override for the weight of this unshaped connection. This attribute is ignored for shaped connections, for ABR connections, for connections on a CQC-based ATM FP and basic VPTs. When the value is set to sameAsCa, the weight is determined by the weight policy attribute under the CA service category component for all but standard VPT VCCs. For standard VPT VCCs, the weight is determined by the VCC's service category, when the value is set to sameAsCa. When this attribute is set to a value from 1 to 4095, that value is used for the weight policy of this connection relative to other connections. For all but standard VPT VCCs, weight policy determines the proportion of transit cell opportunities which are allocated to this connection, compared to other connections in the same service category. For standard VPT VCCs, weight policy determines the proportion of transmit cell opportunities which are allocated to this connection, compared to other connections associated with the VPT. When the value is set to upToQueueLimit, the weight policy is limited only by the txQueueLimit. VALUES ( 0 = upToQueueLimit 65535 = sameAsCa )
INT mscAtmIfVptIispSigVcdQosClass	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1.21	INTEGER	read-write	This attribute specifies the quality of service for both the forward and backward direction for this connection. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters.
INT mscAtmIfVptIispSigVcdTrafficShaping	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1.50	INTEGER	read-write	This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. When sameAsCa is selected, traffic shaping for this connection is based on the trafficShaping attribute of the connection's service category component under the AtmIf CA. If the service category has traffic shaping enabled, then traffic shaping is enabled for the connection. Note that enabling traffic shaping may have no effect under certain cases. These cases are listed in the description of the trafficShaping operational attribute, which is under the Vcc Tm and Vpc Tm components. When disabled is selected, traffic shaping for this connection is disabled.
INT mscAtmIfVptIispSigVcdUnshapedTransmitQueueing	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1.60	INTEGER	read-write	This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this connection if it is unshaped. Refer to the unshapedTransmitQueueing attribute under the AtmIf CA service category subcomponent for more details on the meaning of this attribute. When this attribute is set to sameAsCa, the transmit queueing method for the connection is based on the unshapedTransmitQueueing attribute of the connection's service category component under the ConnectionAdministrator. When this attribute is set to common, transmit traffic on this unshaped connection is destined for the common queue. The value sameAsInterface is for migration from previous software releases, but should no longer be used
INT mscAtmIfVptIispSigVcdUsageParameterControl	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1.70	INTEGER	read-write	This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface. When sameAsCa is selected, UPC for the connection is based on the usageParameterControl attribute of the connection's service category component under the ConnectionAdministrator. If the service category has UPC enabled, then UPC is enabled for the connection. Note that enabling UPC may have no effect under certain cases. These cases are listed in the description of the usageParameterControl operational attribute, which is under the Vcc Tm or Vpc Tm component. When disabled is selected, UPC for this connection is disabled. The value sameAsInterface is for migration from previous software releases, but should no longer be used
mscAtmIfVptIispSigVcdTdpTable	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.387		not-accessible	This attribute is a vector of five traffic parameters whose meanings are defined by the trafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When trafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When trafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For trafficDescType 3 the traffic is shaped at the next rate less than the PCR. For trafficDescType 6, 7, and 8, the traffic is shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic is shaped at the next rate above the PCR.
mscAtmIfVptIispSigVcdTdpEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.387.1		not-accessible	An entry in the mscAtmIfVptIispSigVcdTdpTable.
I32 mscAtmIfVptIispSigVcdTdpIndex	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.387.1.1	Integer32	not-accessible	This variable represents the mscAtmIfVptIispSigVcdTdpTable specific index for the mscAtmIfVptIispSigVcdTdpTable.
U32 mscAtmIfVptIispSigVcdTdpValue	1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.387.1.2	Unsigned32	read-write	This variable represents an individual value for the mscAtmIfVptIispSigVcdTdpTable.
mscAtmIfVptIispSigProvTable	1.3.6.1.4.1.562.36.2.1.114.9.6.3.10		not-accessible	This attribute group contains the provisionable attributes for the Signalling component.
mscAtmIfVptIispSigProvEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.3.10.1		not-accessible	An entry in the mscAtmIfVptIispSigProvTable.
U32 mscAtmIfVptIispSigVci	1.3.6.1.4.1.562.36.2.1.114.9.6.3.10.1.1	Unsigned32	read-write	This attribute specifies the signalling channel number.
INT mscAtmIfVptIispSigAddressConversion	1.3.6.1.4.1.562.36.2.1.114.9.6.3.10.1.2	INTEGER	read-write	This attribute specifies the address conversion on the outgoing signalling PDUs. The options are none, nativeE164, or nsap. The none option is the default and if this option is chosen then nothing is done to the address information element (IE) in the outgoing signalling message. If nativeE164 option is chosen, then only NSAP encapsulated E.164 addresses with zeros in the ESI are converted to native E.164 format in the outgoing signalling message. If the NSAP address is not encapsulated E.164 or the ESI field is not zeros and the nativeE164 option is chosen, then the call is cleared. If the nsap option is chosen, then native E.164 addresses are converted to NSAP E.164 with zeros in the ESI field; otherwise the address is in NSAP format and is not changed.
INT mscAtmIfVptIispSigOperatingMode	1.3.6.1.4.1.562.36.2.1.114.9.6.3.10.1.3	INTEGER	read-write	This attribute specifies the operating mode of the signaling channel. provisionedOnly indicates that only SPVCs and SPVPs are supported on the interface and SVCs are not supported. This value is permitted only on UNI interfaces. normal indicates that SVCs, SPVCs, and SPVPs are supported on the interface.
mscAtmIfVptIispSigStateTable	1.3.6.1.4.1.562.36.2.1.114.9.6.3.11		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
mscAtmIfVptIispSigStateEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.3.11.1		not-accessible	An entry in the mscAtmIfVptIispSigStateTable.
INT mscAtmIfVptIispSigAdminState	1.3.6.1.4.1.562.36.2.1.114.9.6.3.11.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT mscAtmIfVptIispSigOperationalState	1.3.6.1.4.1.562.36.2.1.114.9.6.3.11.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT mscAtmIfVptIispSigUsageState	1.3.6.1.4.1.562.36.2.1.114.9.6.3.11.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
mscAtmIfVptIispSigOperTable	1.3.6.1.4.1.562.36.2.1.114.9.6.3.12		not-accessible	This attribute contains the operational attributes for the AtmSignalling component.
mscAtmIfVptIispSigOperEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.3.12.1		not-accessible	An entry in the mscAtmIfVptIispSigOperTable.
U32 mscAtmIfVptIispSigLastTxCauseCode	1.3.6.1.4.1.562.36.2.1.114.9.6.3.12.1.1	Unsigned32	read-only	This attribute indicates the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX mscAtmIfVptIispSigLastTxDiagCode	1.3.6.1.4.1.562.36.2.1.114.9.6.3.12.1.2	Hex	read-only	This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
U32 mscAtmIfVptIispSigLastRxCauseCode	1.3.6.1.4.1.562.36.2.1.114.9.6.3.12.1.3	Unsigned32	read-only	This attribute contains the cause code in the last received signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX mscAtmIfVptIispSigLastRxDiagCode	1.3.6.1.4.1.562.36.2.1.114.9.6.3.12.1.4	Hex	read-only	This attribute contains the diagnostic code in the last received signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
mscAtmIfVptIispSigStatsTable	1.3.6.1.4.1.562.36.2.1.114.9.6.3.13		not-accessible	This attribute group contains the statistics associated with the AtmSignalling component.
mscAtmIfVptIispSigStatsEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1		not-accessible	An entry in the mscAtmIfVptIispSigStatsTable.
C32 mscAtmIfVptIispSigCurrentConnections	1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.1	Counter32	read-only	This attribute indicates the total number of currently active connections.
G32 mscAtmIfVptIispSigPeakConnections	1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.2	Gauge32	read-only	This attribute indicates the high water mark of active point-to- point and point-to-multipoint connections.
C32 mscAtmIfVptIispSigSuccessfulConnections	1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.3	Counter32	read-only	This attribute counts the total number of switched point-to- point and point-to-multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 mscAtmIfVptIispSigFailedConnections	1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.4	Counter32	read-only	This attribute counts the total number of switched connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
C32 mscAtmIfVptIispSigTxPdus	1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.5	Counter32	read-only	This attribute counts the number of transmitted signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
C32 mscAtmIfVptIispSigRxPdus	1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.6	Counter32	read-only	This attribute counts the number of received signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
G32 mscAtmIfVptIispSigCurrentPmpConnections	1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.7	Gauge32	read-only	This attribute indicates the number of currently active point-to- multipoint connections.
G32 mscAtmIfVptIispSigPeakPmpConnections	1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.8	Gauge32	read-only	This attribute indicates the high water mark of active point-to- multipoint connections.
C32 mscAtmIfVptIispSigSuccessfulPmpConnections	1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.9	Counter32	read-only	This attribute counts the total number of switched point-to- multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 mscAtmIfVptIispSigFailedPmpConnections	1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.10	Counter32	read-only	This attribute counts the number of switched point-to- multipoint connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
G32 mscAtmIfVptIispSigNewCurrentConnections	1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.11	Gauge32	read-only	This attribute indicates the total number of currently active point-to- point and point-to-multipoint connections.
mscAtmIfVptIispAddr	1.3.6.1.4.1.562.36.2.1.114.9.6.4
mscAtmIfVptIispAddrRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.9.6.4.1		not-accessible	This entry controls the addition and deletion of mscAtmIfVptIispAddr components.
mscAtmIfVptIispAddrRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.4.1.1		not-accessible	A single entry in the table represents a single mscAtmIfVptIispAddr component.
ROW mscAtmIfVptIispAddrRowStatus	1.3.6.1.4.1.562.36.2.1.114.9.6.4.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfVptIispAddr components. These components can be added and deleted.
STR mscAtmIfVptIispAddrComponentName	1.3.6.1.4.1.562.36.2.1.114.9.6.4.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfVptIispAddrStorageType	1.3.6.1.4.1.562.36.2.1.114.9.6.4.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfVptIispAddr tables.
STR mscAtmIfVptIispAddrAddressIndex	1.3.6.1.4.1.562.36.2.1.114.9.6.4.1.1.10	AsciiStringIndex	not-accessible	This variable represents an index for the mscAtmIfVptIispAddr tables.
INT mscAtmIfVptIispAddrAddressTypeIndex	1.3.6.1.4.1.562.36.2.1.114.9.6.4.1.1.11	INTEGER	not-accessible	This variable represents an index for the mscAtmIfVptIispAddr tables.
mscAtmIfVptIispAddrTermSP	1.3.6.1.4.1.562.36.2.1.114.9.6.4.2
mscAtmIfVptIispAddrTermSPRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.9.6.4.2.1		not-accessible	This entry controls the addition and deletion of mscAtmIfVptIispAddrTermSP components.
mscAtmIfVptIispAddrTermSPRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.4.2.1.1		not-accessible	A single entry in the table represents a single mscAtmIfVptIispAddrTermSP component.
ROW mscAtmIfVptIispAddrTermSPRowStatus	1.3.6.1.4.1.562.36.2.1.114.9.6.4.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfVptIispAddrTermSP components. These components can be added and deleted.
STR mscAtmIfVptIispAddrTermSPComponentName	1.3.6.1.4.1.562.36.2.1.114.9.6.4.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfVptIispAddrTermSPStorageType	1.3.6.1.4.1.562.36.2.1.114.9.6.4.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfVptIispAddrTermSP tables.
NON mscAtmIfVptIispAddrTermSPIndex	1.3.6.1.4.1.562.36.2.1.114.9.6.4.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscAtmIfVptIispAddrTermSP tables.
mscAtmIfVptIispAddrPnniInfo	1.3.6.1.4.1.562.36.2.1.114.9.6.4.3
mscAtmIfVptIispAddrPnniInfoRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.1		not-accessible	This entry controls the addition and deletion of mscAtmIfVptIispAddrPnniInfo components.
mscAtmIfVptIispAddrPnniInfoRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.1.1		not-accessible	A single entry in the table represents a single mscAtmIfVptIispAddrPnniInfo component.
ROW mscAtmIfVptIispAddrPnniInfoRowStatus	1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfVptIispAddrPnniInfo components. These components can be added and deleted.
STR mscAtmIfVptIispAddrPnniInfoComponentName	1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfVptIispAddrPnniInfoStorageType	1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfVptIispAddrPnniInfo tables.
NON mscAtmIfVptIispAddrPnniInfoIndex	1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscAtmIfVptIispAddrPnniInfo tables.
mscAtmIfVptIispAddrPnniInfoProvTable	1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.10		not-accessible	This attribute group contains the provisioned attributes relating to PNNI for a PnniInfo component.
mscAtmIfVptIispAddrPnniInfoProvEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.10.1		not-accessible	An entry in the mscAtmIfVptIispAddrPnniInfoProvTable.
INT mscAtmIfVptIispAddrPnniInfoScope	1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.10.1.1	INTEGER	read-write	This attribute specifies the scope of the ATM address, which is the highest level up to which this address will be advertised in the PNNI hierarchy. The scope must be set to a value numerically less than or equal to the level of the lowest level peer group containing this node. Setting the scope to 0 will cause the address to be advertised globally within this PNNI routing domain.
INT mscAtmIfVptIispAddrPnniInfoReachability	1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.10.1.2	INTEGER	read-write	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
mscAtmIfVptIispAddrOperTable	1.3.6.1.4.1.562.36.2.1.114.9.6.4.10		not-accessible	This attribute group contains the operational attributes for the Address component.
mscAtmIfVptIispAddrOperEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.4.10.1		not-accessible	An entry in the mscAtmIfVptIispAddrOperTable.
INT mscAtmIfVptIispAddrScope	1.3.6.1.4.1.562.36.2.1.114.9.6.4.10.1.1	INTEGER	read-only	This attribute indicates the scope of the ATM address, which is the highest level to which this address will be advertised in the PNNI hierarchy. If no PnniInfo subcomponent has been provisioned, then the scope will default to the level of this node in the PNNI hierarchy. If this node does not participate in a PNNI hierarchy, then this attribute will have the value of -1.
INT mscAtmIfVptIispAddrReachability	1.3.6.1.4.1.562.36.2.1.114.9.6.4.10.1.2	INTEGER	read-only	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
mscAtmIfVptIispCallingAScr	1.3.6.1.4.1.562.36.2.1.114.9.6.5
mscAtmIfVptIispCallingAScrRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.9.6.5.1		not-accessible	This entry controls the addition and deletion of mscAtmIfVptIispCallingAScr components.
mscAtmIfVptIispCallingAScrRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.5.1.1		not-accessible	A single entry in the table represents a single mscAtmIfVptIispCallingAScr component.
ROW mscAtmIfVptIispCallingAScrRowStatus	1.3.6.1.4.1.562.36.2.1.114.9.6.5.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfVptIispCallingAScr components. These components can be added and deleted.
STR mscAtmIfVptIispCallingAScrComponentName	1.3.6.1.4.1.562.36.2.1.114.9.6.5.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfVptIispCallingAScrStorageType	1.3.6.1.4.1.562.36.2.1.114.9.6.5.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfVptIispCallingAScr tables.
NON mscAtmIfVptIispCallingAScrIndex	1.3.6.1.4.1.562.36.2.1.114.9.6.5.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscAtmIfVptIispCallingAScr tables.
mscAtmIfVptIispCallingAScrAddr	1.3.6.1.4.1.562.36.2.1.114.9.6.5.2
mscAtmIfVptIispCallingAScrAddrRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.9.6.5.2.1		not-accessible	This entry controls the addition and deletion of mscAtmIfVptIispCallingAScrAddr components.
mscAtmIfVptIispCallingAScrAddrRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.5.2.1.1		not-accessible	A single entry in the table represents a single mscAtmIfVptIispCallingAScrAddr component.
ROW mscAtmIfVptIispCallingAScrAddrRowStatus	1.3.6.1.4.1.562.36.2.1.114.9.6.5.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfVptIispCallingAScrAddr components. These components can be added and deleted.
STR mscAtmIfVptIispCallingAScrAddrComponentName	1.3.6.1.4.1.562.36.2.1.114.9.6.5.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfVptIispCallingAScrAddrStorageType	1.3.6.1.4.1.562.36.2.1.114.9.6.5.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfVptIispCallingAScrAddr tables.
STR mscAtmIfVptIispCallingAScrAddrAddressIndex	1.3.6.1.4.1.562.36.2.1.114.9.6.5.2.1.1.10	AsciiStringIndex	not-accessible	This variable represents an index for the mscAtmIfVptIispCallingAScrAddr tables.
INT mscAtmIfVptIispCallingAScrAddrAddressActionIndex	1.3.6.1.4.1.562.36.2.1.114.9.6.5.2.1.1.11	INTEGER	not-accessible	This variable represents an index for the mscAtmIfVptIispCallingAScrAddr tables.
mscAtmIfVptIispCallingAScrProvTable	1.3.6.1.4.1.562.36.2.1.114.9.6.5.10		not-accessible	This attribute group contains the provisionable attributes for the CallingAScr component.
mscAtmIfVptIispCallingAScrProvEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.5.10.1		not-accessible	An entry in the mscAtmIfVptIispCallingAScrProvTable.
INT mscAtmIfVptIispCallingAScrAdminStatus	1.3.6.1.4.1.562.36.2.1.114.9.6.5.10.1.1	INTEGER	read-write	This attribute specifies whether the calling address screening feature is enabled or disabled. If enabled, incoming SVC calls are screened against provisioned addresses. If enabled and the calling address in the ATM SVC call request is provisioned to be accepted, the call is accepted or rejected according to the action specified for that address. If the value is enabled, and the calling address in the address request is not provisioned, the call is rejected If the value is disabled, no calling address screening is performed.
STR mscAtmIfVptIispCallingAScrDefaultInsertionAddress	1.3.6.1.4.1.562.36.2.1.114.9.6.5.10.1.2	HexString	read-write	This attribute specifies the address to be inserted into the SVC connection request if adminStatus is enabled and the connection request does not contain a calling address. If the adminStatus attribute is enabled and this attribute is empty, all incoming SVC calls which do not contain a calling address are rejected.
mscAtmIfVptIispCallingAScrStatTable	1.3.6.1.4.1.562.36.2.1.114.9.6.5.11		not-accessible	This attribute group contains statistics related to the incoming SVC call requests received while the adminStatus attribute is set to enabled.
mscAtmIfVptIispCallingAScrStatEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.5.11.1		not-accessible	An entry in the mscAtmIfVptIispCallingAScrStatTable.
C32 mscAtmIfVptIispCallingAScrAcceptedCalls	1.3.6.1.4.1.562.36.2.1.114.9.6.5.11.1.1	Counter32	read-only	This attribute counts the incoming SVC calls which were accepted because the address specified in the call request matched a provisioned ATM address and the associated action was accept. When the counter exceeds the maximum, it wraps to 0.
C32 mscAtmIfVptIispCallingAScrRejectedCalls	1.3.6.1.4.1.562.36.2.1.114.9.6.5.11.1.2	Counter32	read-only	This attribute counts the incoming SVC calls which were rejected because the address specified in the call request matched a provisioned ATM address, but the associated action was reject. When the counter exceeds the maximum, it wraps to 0.
C32 mscAtmIfVptIispCallingAScrUnmatchedCalls	1.3.6.1.4.1.562.36.2.1.114.9.6.5.11.1.3	Counter32	read-only	This attribute counts the incoming SVC calls which were rejected because none of the provisioned ATM addresses matched the applicable address in the incoming SVC call request. When the counter exceeds the maximum, it wraps to 0.
mscAtmIfVptIispCalledAScr	1.3.6.1.4.1.562.36.2.1.114.9.6.6
mscAtmIfVptIispCalledAScrRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.9.6.6.1		not-accessible	This entry controls the addition and deletion of mscAtmIfVptIispCalledAScr components.
mscAtmIfVptIispCalledAScrRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.6.1.1		not-accessible	A single entry in the table represents a single mscAtmIfVptIispCalledAScr component.
ROW mscAtmIfVptIispCalledAScrRowStatus	1.3.6.1.4.1.562.36.2.1.114.9.6.6.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfVptIispCalledAScr components. These components can be added and deleted.
STR mscAtmIfVptIispCalledAScrComponentName	1.3.6.1.4.1.562.36.2.1.114.9.6.6.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfVptIispCalledAScrStorageType	1.3.6.1.4.1.562.36.2.1.114.9.6.6.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfVptIispCalledAScr tables.
NON mscAtmIfVptIispCalledAScrIndex	1.3.6.1.4.1.562.36.2.1.114.9.6.6.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscAtmIfVptIispCalledAScr tables.
mscAtmIfVptIispCalledAScrAddr	1.3.6.1.4.1.562.36.2.1.114.9.6.6.2
mscAtmIfVptIispCalledAScrAddrRowStatusTable	1.3.6.1.4.1.562.36.2.1.114.9.6.6.2.1		not-accessible	This entry controls the addition and deletion of mscAtmIfVptIispCalledAScrAddr components.
mscAtmIfVptIispCalledAScrAddrRowStatusEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.6.2.1.1		not-accessible	A single entry in the table represents a single mscAtmIfVptIispCalledAScrAddr component.
ROW mscAtmIfVptIispCalledAScrAddrRowStatus	1.3.6.1.4.1.562.36.2.1.114.9.6.6.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscAtmIfVptIispCalledAScrAddr components. These components can be added and deleted.
STR mscAtmIfVptIispCalledAScrAddrComponentName	1.3.6.1.4.1.562.36.2.1.114.9.6.6.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscAtmIfVptIispCalledAScrAddrStorageType	1.3.6.1.4.1.562.36.2.1.114.9.6.6.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscAtmIfVptIispCalledAScrAddr tables.
STR mscAtmIfVptIispCalledAScrAddrAddressIndex	1.3.6.1.4.1.562.36.2.1.114.9.6.6.2.1.1.10	AsciiStringIndex	not-accessible	This variable represents an index for the mscAtmIfVptIispCalledAScrAddr tables.
INT mscAtmIfVptIispCalledAScrAddrAddressActionIndex	1.3.6.1.4.1.562.36.2.1.114.9.6.6.2.1.1.11	INTEGER	not-accessible	This variable represents an index for the mscAtmIfVptIispCalledAScrAddr tables.
mscAtmIfVptIispCalledAScrProvTable	1.3.6.1.4.1.562.36.2.1.114.9.6.6.10		not-accessible	This attribute group contains the provisionable attributes for the CalledAScr component.
mscAtmIfVptIispCalledAScrProvEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.6.10.1		not-accessible	An entry in the mscAtmIfVptIispCalledAScrProvTable.
INT mscAtmIfVptIispCalledAScrAdminStatus	1.3.6.1.4.1.562.36.2.1.114.9.6.6.10.1.1	INTEGER	read-write	This attribute specifies whether the called address screening feature is enabled or disabled. If the value is enabled, incoming SVC calls will be screened against provisioned called addresses. If the value is enabled and the called address in the ATM SVC call request has been provisioned, the call is accepted or rejected according to the action specified for that address. If the value is enabled and the called address in the call request is not provisioned, the call is rejected. If the value is disabled, no called address screening is performed.
mscAtmIfVptIispCalledAScrStatTable	1.3.6.1.4.1.562.36.2.1.114.9.6.6.11		not-accessible	This attribute group contains statistics related to the incoming SVC call requests received while the adminStatus attribute is set to enabled.
mscAtmIfVptIispCalledAScrStatEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.6.11.1		not-accessible	An entry in the mscAtmIfVptIispCalledAScrStatTable.
C32 mscAtmIfVptIispCalledAScrAcceptedCalls	1.3.6.1.4.1.562.36.2.1.114.9.6.6.11.1.1	Counter32	read-only	This attribute counts the incoming SVC calls which were accepted because the address specified in the call request matched a provisioned ATM address and the associated action was accept. When the counter exceeds the maximum, it wraps to 0.
C32 mscAtmIfVptIispCalledAScrRejectedCalls	1.3.6.1.4.1.562.36.2.1.114.9.6.6.11.1.2	Counter32	read-only	This attribute counts the incoming SVC calls which were rejected because the address specified in the call request matched a provisioned ATM address, but the associated action was reject. When the counter exceeds the maximum, it wraps to 0.
C32 mscAtmIfVptIispCalledAScrUnmatchedCalls	1.3.6.1.4.1.562.36.2.1.114.9.6.6.11.1.3	Counter32	read-only	This attribute counts the incoming SVC calls which were rejected because none of the provisioned ATM addresses matched the applicable address in the incoming SVC call request. When the counter exceeds the maximum, it wraps to 0.
mscAtmIfVptIispProvTable	1.3.6.1.4.1.562.36.2.1.114.9.6.10		not-accessible	This group contains the provisionable attributes for the Iisp component.
mscAtmIfVptIispProvEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.10.1		not-accessible	An entry in the mscAtmIfVptIispProvTable.
INT mscAtmIfVptIispVersion	1.3.6.1.4.1.562.36.2.1.114.9.6.10.1.1	INTEGER	read-write	This attribute indicates which specification the IISP interface complies with. The options are iisp10Sig30 which refers to IISP version 1.0 with 3.0 signalling and iisp10Sig31 which refers to IISP version 1.0 with 3.1 signalling. If this attribute is changed, all switched Vcc components in this interface are cleared due to the fact that the two versions are incompatible.
INT mscAtmIfVptIispSide	1.3.6.1.4.1.562.36.2.1.114.9.6.10.1.2	INTEGER	read-write	This attribute indicates which side the interface is, user or network.
U32 mscAtmIfVptIispSoftPvcRetryPeriod	1.3.6.1.4.1.562.36.2.1.114.9.6.10.1.3	Unsigned32	read-write	This attribute specifies the time to wait between call set up retries. The resolution is to the nearest 10 seconds. This attribute has been obsoleted and is replaced by the softPvpAndPvcRetryPeriod attribute.
U32 mscAtmIfVptIispSoftPvpAndPvcRetryPeriod	1.3.6.1.4.1.562.36.2.1.114.9.6.10.1.4	Unsigned32	read-write	This attribute specifies the time to wait between soft PVP or soft PVC call setup retries. The resolution is to the nearest 10 seconds.
U32 mscAtmIfVptIispSoftPvpAndPvcHoldOffTime	1.3.6.1.4.1.562.36.2.1.114.9.6.10.1.5	Unsigned32	read-write	This attribute specifies how long to hold off retries following a release or the connection. The resolution is to the nearest 50 ms.
mscAtmIfVptIispAcctOptTable	1.3.6.1.4.1.562.36.2.1.114.9.6.11		not-accessible	This group contains the provisionable attributes for accounting.
mscAtmIfVptIispAcctOptEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.11.1		not-accessible	An entry in the mscAtmIfVptIispAcctOptTable.
OCT mscAtmIfVptIispAccountCollection	1.3.6.1.4.1.562.36.2.1.114.9.6.11.1.1	OCTET STRING	read-write	This attribute is used to turn accounting on or off for SVC and SPVC connections. It also specifies the reason(s) for which accounting data is collected: billing, test, study, audit, or force. If the set of reasons is not empty then accounting records will be generated by this interface in the following situations: - on a TODA changeover if TODA is enabled; - every 12 hours (per connection) if TODA is disabled; - on every call clear (a call record with final cell counts). If none of the reasons is present, then accounting will be suppressed. The reason for collection is recorded in the accounting record, in the attribute callingCollectReason or calledCollectReason as appropriate. Description of bits: bill(0) test(1) study(2) audit(3) force(4)
INT mscAtmIfVptIispAccountConnectionType	1.3.6.1.4.1.562.36.2.1.114.9.6.11.1.2	INTEGER	read-write	This attribute specifies whether accounting records generated by this interface should be marked as originating, terminating or intermediate. This attribute, in combination with the direction of the call, determines the value of attribute connPointType of the accounting record and may be used by downstream accounting processes to correlate the records. If the value is origTerm then records generated for incoming calls will be marked as originating and records generated for outgoing calls will be marked as terminating. If the value is intermediate then records generated for all calls will be marked as intermediate.
U32 mscAtmIfVptIispAccountClass	1.3.6.1.4.1.562.36.2.1.114.9.6.11.1.3	Unsigned32	read-write	This attribute specifies the accounting class associated with the interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingServiceType or calledServiceType as appropriate.
U32 mscAtmIfVptIispServiceExchange	1.3.6.1.4.1.562.36.2.1.114.9.6.11.1.4	Unsigned32	read-write	This attribute specifies the data service exchange associated with this interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingDse or calledDse as appropriate.
mscAtmIfVptIispVProvTable	1.3.6.1.4.1.562.36.2.1.114.9.6.12		not-accessible	This group contains the provisionable attributes for the Iisp component which are specific to virtual IISP interfaces.
mscAtmIfVptIispVProvEntry	1.3.6.1.4.1.562.36.2.1.114.9.6.12.1		not-accessible	An entry in the mscAtmIfVptIispVProvTable.
U32 mscAtmIfVptIispVpci	1.3.6.1.4.1.562.36.2.1.114.9.6.12.1.1	Unsigned32	read-write	This attribute specifies the Virtual Path Connection Identifier (VPCI) to be used between this signalling entity and its peer. The VPCI of the peer virtual IISP must have the same value for switched connections to be set up across the interface.
atmIispMIB	1.3.6.1.4.1.562.36.2.2.70
atmIispGroup	1.3.6.1.4.1.562.36.2.2.70.1
atmIispGroupCA	1.3.6.1.4.1.562.36.2.2.70.1.1
atmIispGroupCA02	1.3.6.1.4.1.562.36.2.2.70.1.1.3
atmIispGroupCA02A	1.3.6.1.4.1.562.36.2.2.70.1.1.3.2
atmIispCapabilities	1.3.6.1.4.1.562.36.2.2.70.3
atmIispCapabilitiesCA	1.3.6.1.4.1.562.36.2.2.70.3.1
atmIispCapabilitiesCA02	1.3.6.1.4.1.562.36.2.2.70.3.1.3
atmIispCapabilitiesCA02A	1.3.6.1.4.1.562.36.2.2.70.3.1.3.2

RFC description

Manages ATM Interim Inter-switch Signaling Protocol (IISP) interfaces and virtual path configurations on Nortel MsCarrier switches.

Start monitoring Nortel MSC Passport ATM switch (IISP inter-switch signaling) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Nortel-MsCarrier-MscPassport-AtmIispMIB

What Is Nortel-MsCarrier-MscPassport-AtmIispMIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description