| OID symbolic | OID numeric | Type | Access | Description |
|---|
| mplsFrrMIB | 1.3.6.1.2.1.113 | | | Copyright (C) 2006 The IETF Trust. This
MIB module is part of RFC 4327; see the RFC itself
for full legal notices.
This MIB module contains managed object definitions for
MPLS Traffic Engineering Fast Reroute as defined in
RFC4090. |
| mplsFrrNotif | 1.3.6.1.2.1.113.0 | | | |
| NTF mplsFrrFacProtected | 1.3.6.1.2.1.113.0.1 | | | This notification is generated when a tunnel running over an
interface as specified in the mplsFrrConstTable is initially
protected by the backup tunnel also specified in the
mplsFrrConstTable. In some implementations there may be
a difference between when the control plane triggers
this notification and when the hardware is programmed to
utilize the protection path. Due to the urgency of this
operation, it is acceptable for the control plane to
either issue this notification before or after it programs
the hardware. In cases where it is the latter approach,
the notification MUST be sent immediately after the
data plane has been altered.
This notification should not be generated
for each subsequent tunnel that is backed up by the FRR feature
on this LSR, as this may result in potential scaling issues
with regard to LSR performance and network loading. Note also
that notifications MUST be generated in accordance with the
mplsFrrNotifMaxRate.
Note this notification only applicable to the facility based
fastreroute protection method, and should be ignored by
implementations that do not support this method. |
| NTF mplsFrrFacUnProtected | 1.3.6.1.2.1.113.0.2 | | | This notification is generated when the final tunnel that is
being protected by a backup tunnel as specified in the
mplsFrrConstTable is restored to normal operation. This
notification should not be generated for each restored tunnel,
as this may result in potential scaling issues with regard to
LSR performance and network loading. Note also that
notifications MUST be generated in accordance with the
mplsFrrNotifMaxRate.
Note this notification only applicable to the facility based
fastreroute protection method, and should be ignored by
implementations that do not support this method. |
| mplsFrrScalars | 1.3.6.1.2.1.113.1 | | | |
| I32 mplsFrrDetourIncoming | 1.3.6.1.2.1.113.1.1 | Integer32 | read-only | The number of detour LSPs entering the device
(greater than or equal to 0) if mplsFrrProtectionMethod
is set to oneToOneBackup(1), or -1 if
mplsFrrProtectionMethod is set to facilityBackup(2). |
| I32 mplsFrrDetourOutgoing | 1.3.6.1.2.1.113.1.2 | Integer32 | read-only | The number of detour LSPs leaving the device (greater
than or equal to 0) if mplsFrrProtectionMethod
is set to oneToOneBackup(1), or -1 if
mplsFrrProtectionMethod is set to
facilityBackup(2). |
| I32 mplsFrrDetourOriginating | 1.3.6.1.2.1.113.1.3 | Integer32 | read-only | The number of detour LSPs originating at this PLR (greater
than or equal to 0) if mplsFrrProtectionMethod
is set to oneToOneBackup(1). This object MUST
return -1 if the mplsFrrProtectionMethod is set to
facilityBackup(2). |
| U32 mplsFrrSwitchover | 1.3.6.1.2.1.113.1.4 | Unsigned32 | read-only | The number of tunnel instances for which this LSR
is the ingress that are currently using a detour
or bypass LSP to reach their egress. |
| I32 mplsFrrConfIfs | 1.3.6.1.2.1.113.1.5 | Integer32 | read-only | Indicates the number of MPLS interfaces configured for
protection by the FRR feature if
mplsFrrProtectionMethod
is set to facilityBackup(2), otherwise this value
MUST return -1 to indicate that LSPs traversing any
interface are not protected. |
| U32 mplsFrrActProtectedIfs | 1.3.6.1.2.1.113.1.6 | Unsigned32 | read-only | Indicates the number of interfaces currently being
protected by the FRR feature if
mplsFrrProtectionMethod is set to
facilityBackup(2), otherwise this value should return
0 to indicate that LSPs traversing any interface may
not be protected. This value MUST be less than or equal
to mplsFrrConfIfs except when mplsFrrConfIfs is
set to -1, in which case the value of this object
is meaningless and SHOULD be ignored. |
| U32 mplsFrrConfProtectionTuns | 1.3.6.1.2.1.113.1.7 | Unsigned32 | read-only | Indicates the number of bypass tunnels configured to
protect TE tunnels on this LSR using the FRR feature
if mplsFrrProtectionMethod is set to
facilityBackup(2), otherwise this value MUST return
0 and SHOULD be ignored. |
| U32 mplsFrrActProtectionTuns | 1.3.6.1.2.1.113.1.8 | Unsigned32 | read-only | Indicates the number of bypass tunnels indicated in
mplsFrrConfProtectionTuns whose operStatus
is up(1) indicating that they are currently protecting
TE tunnels on this LSR using the FRR feature. This
object MUST return 0 if mplsFrrProtectionMethod
is set to oneToOneBackup(1). |
| U32 mplsFrrActProtectedLSPs | 1.3.6.1.2.1.113.1.9 | Unsigned32 | read-only | Indicates the number of LSPs currently protected by
the FRR feature where this device acts as the PLR
for those LSPs. If mplsFrrProtectionMethod
is set to facilityBackup(2) this object MUST return
0. |
| INT mplsFrrProtectionMethod | 1.3.6.1.2.1.113.1.10 | INTEGER | read-write | Indicates which protection method is to be used for fast
reroute on this device. Some devices may require a reboot
if this variable is to take affect after being modified. |
| T/F mplsFrrNotifsEnabled | 1.3.6.1.2.1.113.1.11 | TruthValue | read-write | Enables or disables FRR notifications defined in this
MIB module. Notifications are disabled by default. |
| U32 mplsFrrNotifMaxRate | 1.3.6.1.2.1.113.1.12 | Unsigned32 | read-write | This variable indicates the maximum number of
notifications issued per second. If events occur
more rapidly, the implementation may simply fail to
emit these notifications during that period, or may
queue them until an appropriate time. A value of 0
means no throttling is applied and events may be
notified at the rate at which they occur. |
| mplsFrrObjects | 1.3.6.1.2.1.113.2 | | | |
| mplsFrrGeneralObjects | 1.3.6.1.2.1.113.2.1 | | | |
| mplsFrrConstTable | 1.3.6.1.2.1.113.2.1.1 | | not-accessible | This table shows detour LSP or bypass tunnel setup
constraints. |
| mplsFrrConstEntry | 1.3.6.1.2.1.113.2.1.1.1 | | not-accessible | An entry in this table represents detour LSP or bypass
tunnel setup constraints for a tunnel instance to be
protected by detour LSPs or a bypass tunnel.
Agents must only allow entries in this table to be
created for tunnel instances that require fast-reroute
as indicated by the presense of the FAST_REROUTE Object
in the signaling for the LSP in question, as speciifed
in section 4.1 of RFC4090.
Entries indexed with mplsFrrConstIfIndex set to 0 apply to
all interfaces on this device for which the FRR feature can
operate.
Note that as per [RFC3812] the mplsTunnelInstance object
set to a value of 0 indicates that the mplsTunnelEntry
contains at a tunnel ingress. This is typically how
configuration of this feature is performed on devices
where the actual protection LSP used is left up to the
protecting tunnel. However, in cases where static
configuration is possible, any valid tunnel
instance is possible; however, in these cases, it is
STRONGLY RECOMMENDED that the instance index SHOULD
use the following convention to identify backup LSPs:
- lower 16 bits : protected tunnel instance
- higher 16 bits: must be all zeros |
| NUM mplsFrrConstIfIndex | 1.3.6.1.2.1.113.2.1.1.1.1 | InterfaceIndexOrZero | not-accessible | Uniquely identifies an interface which a fast reroute
protection tunnel is configured to potentially protect
in the event of a fault. Entries with this index set to
0 indicates that the protection tunnel configured protects
all interfaces on this device (i.e.: node protection). |
| MPL mplsFrrConstTunnelIndex | 1.3.6.1.2.1.113.2.1.1.1.2 | MplsTunnelIndex | not-accessible | Uniquely identifies a tunnel for which is configured
to possibly protect the interface(s) specified by
mplsFrrConstIfIndex in the event of a fault as
must exist in the mplsTunnelTable. |
| MPL mplsFrrConstTunnelInstance | 1.3.6.1.2.1.113.2.1.1.1.3 | MplsTunnelInstanceIndex | not-accessible | Uniquely identifies an existing instance of this tunnel
for which fast reroute is requested. Note that a value of
0 indicates that the configuration points at a tunnel
head (as specified in RFC3812). This is typically how
configuration of this feature is performed on devices
where the actual protection LSP used is left up to the
protecting tunnel. However, in cases where static
configuration is possible, any valid tunnel
instance is permissible. In these cases, it is recommended
that the instance index follow the following convention
as to make identication of backup LSPs easier:
- lower 16 bits : protected tunnel instance
- higher 16 bits: must be all zeros |
| INT mplsFrrConstProtectionType | 1.3.6.1.2.1.113.2.1.1.1.4 | INTEGER | read-create | Indicates type of the resource protection:
linkProtection(1) indicates that this tunnel is
setup to protect a particular link's resources.
nodeProtection(2) indicates that this tunnel is
setup to protect an entire node from failure. |
| U32 mplsFrrConstSetupPrio | 1.3.6.1.2.1.113.2.1.1.1.5 | Unsigned32 | read-create | Indicates the setup priority of the detour LSP
or bypass tunnel. |
| U32 mplsFrrConstHoldingPrio | 1.3.6.1.2.1.113.2.1.1.1.6 | Unsigned32 | read-create | Indicates the holding priority for detour LSP
or bypass tunnel. |
| MPL mplsFrrConstInclAnyAffinity | 1.3.6.1.2.1.113.2.1.1.1.7 | MplsTunnelAffinity | read-create | Indicates the include-any link constraint for the
detour LSP or bypass tunnel. A link satisfies the
include-any constraint if and only if the constraint
is zero, or the link and the constraint have a
resource class in common. |
| MPL mplsFrrConstInclAllAffinity | 1.3.6.1.2.1.113.2.1.1.1.8 | MplsTunnelAffinity | read-create | Indicates the include-all link constraint for the
detour LSP or bypass tunnel. A link satisfies the
include-all constraint if and only if the link contains
all of the administrative groups specified in the
constraint. |
| MPL mplsFrrConstExclAnyAffinity | 1.3.6.1.2.1.113.2.1.1.1.9 | MplsTunnelAffinity | read-create | Indicates the exclude-any link constraint for the
detour LSP or bypass tunnel. A link satisfies the
exclude-any constraint if and only if the link contains
none of the administrative groups specified in the
constraint. |
| U32 mplsFrrConstHopLimit | 1.3.6.1.2.1.113.2.1.1.1.10 | Unsigned32 | read-create | The maximum number of hops that the detour LSP or
bypass tunnel may traverse. |
| MPL mplsFrrConstBandwidth | 1.3.6.1.2.1.113.2.1.1.1.11 | MplsBitRate | read-create | The maximum bandwidth specifically reserved for detour
LSP or bypass tunnel, in units of thousands of bits
per second (Kbps). Note that setting this value to 0
indicates best-effort treatment. |
| STO mplsFrrConstStorageType | 1.3.6.1.2.1.113.2.1.1.1.12 | StorageType | read-create | The storage type for this configuration entry.
Conceptual rows having the value 'permanent'
need not allow write-access to any columnar
objects in the row. |
| ROW mplsFrrConstRowStatus | 1.3.6.1.2.1.113.2.1.1.1.13 | RowStatus | read-create | This object is used to create, modify, and/or delete a row in
this table. When a row in this table is in active(1)
state, no objects in that row can be modified by the agent
except mplsFrrConstRowStatus and mplsFrrConstStorageType. |
| mplsFrrTunARHopTable | 1.3.6.1.2.1.113.2.1.2 | | not-accessible | This table sparsely extends mplsTunnelARHopTable defined
in the MPLS-TE-STD-MIB MIB module with fast-reroute objects.
These objects specify the status of local protection including
availability and active use, on a per-hop basis, of hops
traversed by a protected tunnel. Note that object
availability in this table is governed by the support of
the Record Route Object in the RSVP-TE signaling of the
implementation. |
| mplsFrrTunARHopEntry | 1.3.6.1.2.1.113.2.1.2.1 | | not-accessible | This entry contains fast-reroute protection status of a single
protected tunnel hop. |
| BIT mplsFrrTunARHopProtectType | 1.3.6.1.2.1.113.2.1.2.1.1 | Bits | read-only | This object indicates the protection type or types of the
associated path hop object. Note that since this object is a
BITS type, one, none or all of the bits may be set to indicate
various combinations of protection types. |
| BIT mplsFrrTunARHopProtectTypeInUse | 1.3.6.1.2.1.113.2.1.2.1.2 | Bits | read-only | This object indicates the protection type or types that are
currently in use by the associated path hop object.
Note that since this object is a BITS type, one, none or all
of the bits may be set to indicate various combinations of
protection types. If no bits are set, this indicates that
no protection types are in use. |
| mplsFrrOne2OneObjects | 1.3.6.1.2.1.113.2.2 | | | |
| mplsFrrOne2OnePlrTable | 1.3.6.1.2.1.113.2.2.1 | | not-accessible | This table shows a list of protected TE tunnels with
the corresponding protecting tunnel, as well as the PLR
where the protecting tunnel that initiated the detour
LSPs that traverse this node. |
| mplsFrrOne2OnePlrEntry | 1.3.6.1.2.1.113.2.2.1.1 | | not-accessible | An entry in this table represents a protected tunnel LSP
together with its detour tunnel instance. An entry in
this table is only created by an SNMP agent as instructed
by an MPLS signaling protocol.
The entries of this table are present in all LSRs on the path
of the detour LSP.
The objects mplsFrrOne2OnePlrTunIdx,
mplsFrrOne2OnePlrTunDetourInst, mplsFrrOne2OnePlrTunIngrLSRId
and mplsFrrOne2OnePlrTunEgrLSRId have the same values as
the objects mplsTunnelIndex, mplsTunnelInstance,
mplsTunnelIngressLSRId and mplsTunnelEgressLSRId of the detour
tunnel instance created in the mplsTunnelTable
(MPLS-TE-STD-MIB). |
| MPL mplsFrrOne2OnePlrTunIdx | 1.3.6.1.2.1.113.2.2.1.1.1 | MplsTunnelIndex | not-accessible | Uniquely identifies a tunnel between a pair of LSRs
from the mplsTunnelEntry. |
| MPL mplsFrrOne2OnePlrTunDetourInst | 1.3.6.1.2.1.113.2.2.1.1.2 | MplsTunnelInstanceIndex | not-accessible | Uniquely identifies a detour instance of a tunnel from
the mplsTunnelEntry.
- lower 16 bits : protected tunnel instance
- higher 16 bits: detour instance |
| OID mplsFrrOne2OnePlrTunIngrLSRId | 1.3.6.1.2.1.113.2.2.1.1.3 | MplsLsrIdentifier | not-accessible | The purpose of this object is to uniquely identity a
tunnel within a network. When the MPLS signalling
protocol is rsvp(2) this object SHOULD contain the
same value as the Extended Tunnel Id field in the
SESSION object. When the MPLS signalling protocol
is crldp(3) this object SHOULD contain the same
value as the Ingress LSR Router ID field in the
LSPID TLV object.
This value represents the head-end of the protected
tunnel instance. |
| OID mplsFrrOne2OnePlrTunEgrLSRId | 1.3.6.1.2.1.113.2.2.1.1.4 | MplsLsrIdentifier | not-accessible | Specifies the egress LSR ID of the protected tunnel instance. |
| OID mplsFrrOne2OnePlrId | 1.3.6.1.2.1.113.2.2.1.1.5 | MplsLsrIdentifier | not-accessible | This value represents the PLR that has initiated a detour LSP
to protect a tunnel instance.
This value is signalled via the DETOUR object defined in MPLS
RSVP protocol as described in RFC-4090. |
| IPt mplsFrrOne2OnePlrSenderAddrType | 1.3.6.1.2.1.113.2.2.1.1.6 | InetAddressType | read-create | Denotes the address type of this detour instance's sender
address. |
| IP mplsFrrOne2OnePlrSenderAddr | 1.3.6.1.2.1.113.2.2.1.1.7 | InetAddress | read-create | The IP address of the PLR which has initiated the detour LSP.
The type of this address is determined by the value of the
mplsFrrOne2OnePlrSenderAddrType object. |
| IPt mplsFrrOne2OnePlrAvoidNAddrType | 1.3.6.1.2.1.113.2.2.1.1.8 | InetAddressType | read-only | Denotes the address type of the node that this PLR tries to
avoid. |
| IP mplsFrrOne2OnePlrAvoidNAddr | 1.3.6.1.2.1.113.2.2.1.1.9 | InetAddress | read-only | The IP address of the node that this PLR tries to avoid.
The type of this address is determined by the value of the
mplsFrrOne2OnePlrAvoidNAddrType object.
This value is signalled via the DETOUR object defined in MPLS
RSVP protocol as described in RFC-4090. |
| mplsFrrDetourTable | 1.3.6.1.2.1.113.2.2.2 | | not-accessible | This table shows detour LSPs. |
| mplsFrrDetourEntry | 1.3.6.1.2.1.113.2.2.2.1 | | not-accessible | An entry in this table represents a detour. An entry in this
table is only created by an SNMP agent as instructed by an MPLS
signaling protocol. |
| T/F mplsFrrDetourActive | 1.3.6.1.2.1.113.2.2.2.1.1 | TruthValue | read-only | Indicates whether or not the main LSP has switched over to
this detour LSP. This is only relevant for detours
originated by this node. |
| INT mplsFrrDetourMerging | 1.3.6.1.2.1.113.2.2.2.1.2 | INTEGER | read-only | This value represents whether or not this detour is merged.
This value MUST be set to none(1) if this detour is not
merged.
This value MUST be set to protectedTunnel(2) if this detour is
merged with the protected tunnel. This value MUST be set to
detour(3) if this detour is merged with another detour
protecting the same tunnel. |
| MPL mplsFrrDetourMergedDetourInst | 1.3.6.1.2.1.113.2.2.2.1.3 | MplsTunnelInstanceIndex | read-only | This value represents the instance of the detour with which
this detour is merged. This object is only valid when
mplsFrrDetourMerging is set to detour(3).
- lower 16 bits : protected tunnel instance
- higher 16 bits: detour instance |
| mplsFrrFacObjects | 1.3.6.1.2.1.113.2.3 | | | |
| mplsFrrFacRouteDBTable | 1.3.6.1.2.1.113.2.3.1 | | not-accessible | The mplsFrrDBTable provides information about the fast
reroute database. Each entry belongs to a protected
interface, protecting backup tunnel and protected tunnel.
MPLS interfaces defined on this node are protected by
backup tunnels and are indicated by the index
mplsFrrFacRouteProtIfIdx. If the interface index is set
to 0, this indicates that the remaining indexes apply
to all configured protected interfaces.
The protecting tunnel is indicated by the second two
indexes (mplsTunnelIndex and mplsTunnelInstance) and
represents a valid mplsTunnelEntry. Note that the tunnel
instance index of the protecting tunnel may be set to 0
which indicates the tunnel head interface for the
protecting tunnel, as per RFC3812, but it may also be
defined using the following semantics:
- lower 16 bits : protected tunnel instance
- higher 16 bits: must be all zeros |
| mplsFrrFacRouteDBEntry | 1.3.6.1.2.1.113.2.3.1.1 | | not-accessible | An entry in the mplsFrrDBTable represents a single
protected LSP, protected by a backup tunnel on a
specific protected interface, or if the interface
index is set to 0, on all interfaces. Note that for
brevity, managers should consult the mplsTunnelTable
present in the MPLS-TE-STD-MIB MIB module for
additional information about the protecting and protected
tunnels, and the ifEntry in the IF-MIB MIB module
for the protected interface. |
| NUM mplsFrrFacRouteProtIfIdx | 1.3.6.1.2.1.113.2.3.1.1.1 | InterfaceIndex | not-accessible | Uniquely identifies the interface configured for FRR
protection. If this object is set to 0, this indicates
that the remaining indexing combinations for this row
applies to all interfaces on this device for which
the FRR feature can operate. |
| MPL mplsFrrFacRouteProtTunIdx | 1.3.6.1.2.1.113.2.3.1.1.2 | MplsTunnelIndex | not-accessible | Uniquely identifies the mplsTunnelEntry primary index for
the tunnel head interface designated to protect the
interface as specified in the mplsFrrFacRouteIfProtIdx
(and all of the tunnels using this interface). Note
that the corresponding mplsTunnelInstance MUST BE
0 as per the indexing convention stipulated in RFC3812,
and thus can be inferred. |
| MPL mplsFrrFacRouteBkupTunIdx | 1.3.6.1.2.1.113.2.3.1.1.3 | MplsTunnelIndex | not-accessible | Uniquely identifies the mplsTunnelEntry primary index for
the TE tunnel LSP being protected on the specified
interface as specified in the mplsFrrFacRouteIfProtIdx. |
| MPL mplsFrrFacRouteBkupTunInst | 1.3.6.1.2.1.113.2.3.1.1.4 | MplsTunnelInstanceIndex | not-accessible | Uniquely identifies the mplsTunnelEntry secondary index
for the TE tunnel LSP being protected on the specified
interface as specified in the mplsFrrFacRouteIfProtIdx. |
| OID mplsFrrFacRouteBkupTunIngrLSRId | 1.3.6.1.2.1.113.2.3.1.1.5 | MplsLsrIdentifier | not-accessible | Uniquely identifies the mplsTunnelEntry third index
for the TE tunnel LSP being protected on the specified
interface as specified in the mplsFrrFacRouteIfProtIdx. |
| OID mplsFrrFacRouteBkupTunEgrLSRId | 1.3.6.1.2.1.113.2.3.1.1.6 | MplsLsrIdentifier | not-accessible | Uniquely identifies the mplsTunnelEntry fourth index
for the TE tunnel LSP being protected on the specified
interface as specified in the mplsFrrFacRouteIfProtIdx. |
| G32 mplsFrrFacRouteDBNumProtTunOnIfEx | 1.3.6.1.2.1.113.2.3.1.1.7 | Gauge32 | read-only | The number of backup tunnels protecting the specified
interface. |
| G32 mplsFrrFacRouteDBNumProtLspOnIf | 1.3.6.1.2.1.113.2.3.1.1.8 | Gauge32 | read-only | The number of LSPs currently being protected on
the specified interface. |
| G32 mplsFrrFacRouteDBNumProtTun | 1.3.6.1.2.1.113.2.3.1.1.9 | Gauge32 | read-only | The number of tunnels protected on this interface. |
| INT mplsFrrFacRouteDBProtTunStatus | 1.3.6.1.2.1.113.2.3.1.1.10 | INTEGER | read-only | Specifies the state of the protected tunnel.
active This tunnel's label has been placed in the
LFIB and is ready to be applied to incoming
packets.
ready - This tunnel's label entry has been created but is
not yet in the LFIB.
partial - This tunnel's label entry as not been fully
created. |
| MPL mplsFrrFacRouteDBProtTunResvBw | 1.3.6.1.2.1.113.2.3.1.1.11 | MplsBitRate | read-only | Specifies the amount of bandwidth in units
of '1,000 bits per second', actually reserved by
the protection tunnel for facility backup purposes.
This value is repeated here from the
MPLS-TE-STD-MIB MIB module because the tunnel entry will
reveal the bandwidth reserved by the signaling protocol,
which is typically 0 for backup tunnels so as to not
over-book bandwidth. However, internal reservations are
typically made on the PLR, thus this value should be
revealed here as it is often different from the one found
in the MPLS-TE-STD-MIB MIB module. |
| mplsFrrConformance | 1.3.6.1.2.1.113.3 | | | |
| mplsFrrGroups | 1.3.6.1.2.1.113.3.1 | | | |
| mplsFrrScalarGroup | 1.3.6.1.2.1.113.3.1.1 | | | Objects that are required to gather fast reroute statistics. |
| mplsFrrConstGroup | 1.3.6.1.2.1.113.3.1.2 | | | Objects that are required to configure fast reroute
constraints at the ingress LSR of the tunnel that requires
fast reroute service. |
| mplsFrrTunARHopGroup | 1.3.6.1.2.1.113.3.1.3 | | | Objects that are required to present per hop fast-reroute
protection status. |
| mplsFrrOne2OnePLRDetourGroup | 1.3.6.1.2.1.113.3.1.4 | | | Objects that are required to present the detour LSP
information at the detour ingress, transit and egress LSRs. |
| mplsFrrOne2OnePlrGroup | 1.3.6.1.2.1.113.3.1.5 | | | Objects that are required to represent the FRR
One-2-One PLR information. |
| mplsFrrFacRouteDBGroup | 1.3.6.1.2.1.113.3.1.6 | | | Objects that are required to represent the FRR
Facility Route Database information. |
| mplsFrrNotifGroup | 1.3.6.1.2.1.113.3.1.7 | | | Objects that are required to represent FRR notifications. |
| mplsFrrCompliances | 1.3.6.1.2.1.113.3.2 | | | |
| mplsFrrModuleFullCompliance | 1.3.6.1.2.1.113.3.2.1 | | | Compliance statements for agents that support the
MPLS-FRR-STD-MIB MIB module. |
| mplsFrrModuleReadOnlyCompliance | 1.3.6.1.2.1.113.3.2.2 | | | Compliance statements for agents that support the MPLS FRR
MIB. |
