All MIBs › JNX-PPP-MIB
Organization: Juniper Networks, Inc.
Last Updated: 2013-09-19
Category: Protocol: PPP, Vendor: Juniper
Description: Defines managed objects for Point-to-Point Protocol (PPP) sessions and link control on Juniper Networks devices.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is JNX-PPP-MIB?
JNX-PPP-MIB is a Juniper Networks enterprise MIB for managing Point-to-Point Protocol (PPP) sessions and link control on Juniper routing platforms. It exposes a link-status table covering per-link PPP negotiation and keepalive state, including termination reasons, negotiation failures, keepalive request/reply counts and failures, magic numbers, and authentication method in use. This data is used to monitor the software/protocol health of WAN links: keepalive failures or a nonzero terminate reason reveal a flapping or dead PPP link, while authentication fields help confirm the expected auth method (e.g., PAP/CHAP) is negotiated. It complements the standard IETF PPP MIB conventions but is a Juniper-specific extension under the jnxPPPObjects/jnxPppLcp/jnxPppSec structure. It is deployed on Juniper routers terminating PPP-encapsulated WAN circuits, such as leased lines or dialup/DDR links. Engineers can download the JNX-PPP-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in JNX-PPP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Juniper Networks router
Monitoring Examples
An operator would poll jnxPppLinkStatusTable/jnxPppLinkStatusEntry per PPP link to check jnxPppLinkStatusTerminateReason and jnxPppLinkStatusTerminateNegFailOption after an unexpected link drop, and compare jnxPppLinkStatusOutKeepaliveRequests against jnxPppLinkStatusInKeepaliveReplies to spot a growing jnxPppLinkStatusKeepaliveFailures count indicating the peer is unresponsive. jnxPppLinkStatusLocalAuthentication would be checked to confirm the negotiated authentication method matches policy, and mismatched jnxPppLinkStatusLocalMagicNumber/jnxPppLinkStatusRemoteMagicNumber values could indicate a looped-back circuit.
What Can Be Monitored
- PPP link status
- link termination reason
- keepalive request/reply counts
- keepalive failure count
- negotiated authentication method
- local/remote magic numbers
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndex | |
| InterfaceIndexOrZero | |
| ifIndex | OBJECT-TYPE |
From IPV6-TC
| Ipv6AddressIfIdentifier |
From JUNIPER-SMI
| jnxPppMibRoot | OBJECT-IDENTITY |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using jnxPppLinkStatusInKeepaliveRequests OID:
Select a Juniper Networks router (PPP WAN circuits) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type jnxPppLinkStatusInKeepaliveRequests into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the number of keepalive requests received. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| jnxPppMIB | 1.3.6.1.4.1.2636.3.68.1 | The Point-to-Point Protocol (PPP) MIB for the Juniper enterprise. | ||
| jnxPPPObjects | 1.3.6.1.4.1.2636.3.68.1.1 | |||
| jnxPppLcp | 1.3.6.1.4.1.2636.3.68.1.1.1 | |||
| jnxPppLinkStatusTable | 1.3.6.1.4.1.2636.3.68.1.1.1.1 | not-accessible | This table contains entries for PPP interfaces present in the system. | |
| jnxPppLinkStatusEntry | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1 | not-accessible | Each entry describes the characteristics of a PPP interface. | |
| INT jnxPppLinkStatusTerminateReason | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1.1 | INTEGER | read-only | Reason the PPP link was terminated: none None. other Not specified. adminDisable Interface administratively disabled. lowerLayerDown Underlying interface is down. noUpperInterface No interface above PPP. authenticationFailure Authentication failed. peerTerminated Peer initiated termination. peerRenegotiated Peer initiated renegotiation. maxRetriesExceeded Maximum number of config retries exceeded. negotiationFailure Failed to negotiate LCP option. keepaliveFailure Keepalive failed. sessionTimeout Maximum session period expired. inactivityTimeout Maximum inactivity period expired. addressLeaseExpired Lease for network address expired. adminLogout Session administratively terminated. tunnelFailed Associated tunnel failed. tunnelDisconnected Associated tunnel disconnected. loopback Loopback detected. |
| INT jnxPppLinkStatusTerminateNegFailOption | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1.2 | INTEGER | read-only | Reports the PPP LCP option for which negotiation failed, when jnxPppLinkStatusTerminateReason has the value negotiationFailure. |
| C32 jnxPppLinkStatusInKeepaliveRequestsEx | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1.3 | Counter32 | read-only | Number of keepalive requests received. |
| C32 jnxPppLinkStatusOutKeepaliveRequests | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1.4 | Counter32 | read-only | Number of keepalive requests transmitted. |
| C32 jnxPppLinkStatusInKeepaliveReplies | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1.5 | Counter32 | read-only | Number of keepalive replies received. |
| C32 jnxPppLinkStatusOutKeepaliveReplies | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1.6 | Counter32 | read-only | Number of keepalive replies transmitted. |
| C32 jnxPppLinkStatusKeepaliveFailures | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1.7 | Counter32 | read-only | Number of keepalive failures detected. |
| I32 jnxPppLinkStatusLocalMagicNumber | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1.8 | Integer32 | read-only | Magic number negotiated for the local side. This has been deprecated and replaced by jnxPppLinkStatusLocalMagicNumber1 |
| I32 jnxPppLinkStatusRemoteMagicNumber | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1.9 | Integer32 | read-only | Magic number negotiated for the remote side. This has been deprecated and replaced by jnxPppLinkStatusRemoteMagicNumber1 |
| JNX jnxPppLinkStatusLocalAuthentication | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1.10 | JnxPppAuthentication2 | read-only | Authentication protocol negotiated for the local side. |
| NUM jnxPppLinkStatusTunnelIfIndex | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1.11 | InterfaceIndexOrZero | read-only | The ifIndex of an associated interface pertaining to a tunneling protocol, or zero if no such interface exists.The type of tunneling interface can be identified from information in the entries in ifTable and jnxIfTable for this tunnel interface. |
| C32 jnxPppLinkStatuslcpRenegoTerminates | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1.12 | Counter32 | read-only | Number of times lcp terminated due to peer exceeding max renegotiation attempts. |
| U32 jnxPppLinkStatusLocalMagicNumber1 | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1.13 | Unsigned32 | read-only | Magic number negotiated for the local side. |
| U32 jnxPppLinkStatusRemoteMagicNumber1 | 1.3.6.1.4.1.2636.3.68.1.1.1.1.1.14 | Unsigned32 | read-only | Magic number negotiated for the remote side. |
| jnxPppLinkConfigTable | 1.3.6.1.4.1.2636.3.68.1.1.1.2 | not-accessible | This table contains entries for PPP interfaces present in the system. | |
| jnxPppLinkConfigEntry | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1 | not-accessible | Each entry describes the characteristics of a PPP interface. Creating or deleting entries in this table causes corresponding entries for be created or deleted in ifTable,ifXTable,jnxIfTable. | |
| NUM jnxPppLinkConfigIfIndex | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.1 | InterfaceIndex | not-accessible | The ifIndex of the PPP interface. When creating entries in this table, suitable values for this object are determined by reading jnxPppNextIfIndex. |
| ROW jnxPppLinkConfigRowStatus | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.2 | RowStatus | read-only | Controls creation or deletion of entries in this table with READ-CREATE maximum access according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: jnxPppLinkConfigRowStatus jnxPppLinkConfigLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for jnxPppLinkConfigIndex must have been determined previously, by reading jnxPppNextIfIndex.The interface identified by jnxPppLinkConfigLowerIfIndex must exist. A corresponding entry in Table or ifXTable or jnxIfTable is created or destroyed as a result of creating or destroying an entry in this table. The following values can be read from this object: active(1) |
| NUM jnxPppLinkConfigLowerIfIndex | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.3 | InterfaceIndexOrZero | read-only | The ifIndex of an interface over which this PPP interface is to be layered.A value of zero indicates no layering. An implementation may choose to require that a non-zero value be configured at entry creation. |
| I32 jnxPppLinkConfigKeepalive | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.4 | Integer32 | read-only | Keepalive interval in seconds. A value of zero disables keepalive. Keepalive is performed using LCP Echo. |
| JNX jnxPppLinkConfigAuthentication | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.5 | JnxPppAuthentication | read-only | Specifies the type(s) of authentication, if any, to be negotiated with the peer: none No authentication is negotiated. pap PAP negotiation only. chap CHAP negotiation only. papChap PAP negotiation is attempted first; if fails, attempt CHAP. chapPap CHAP negotiation is attempted first; if fails, attempt PAP. If authentication negotiation is not supported for this PPP interface, then any attempt to explicitely set this object if READ-CREATE maximum access is supported will result in a notWritable error and it will be implicitily set to the DEFVAL on row creation. Setting this object to none(0) will set jnxPppLinkConfigAuthenticatorRouting Instance object to an empty string. This object returns a null(0) value on the get operation. New object jnxPppLinkConfigAuthentication2 will reflect the configured values. Setting this object along with the jnxPppLinkConfigAuthentication2 object will return an inconsistentValue error. |
| I32 jnxPppLinkConfigMaxAuthenRetries | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.6 | Integer32 | read-only | The number of authentication retries permitted, in addition to a failed initial attempt. If all retries fail, the link is reset. If authentication negotiation is not supported for this PPP interface, then any attempt to explicitely set this object if READ-CREATE maximum access is supported will result in a notWritable error and it will be implicitily set to the DEFVAL on row creation. |
| NUM jnxPppLinkConfigStandardIfIndex | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.7 | InterfaceIndex | read-only | The ifIndex value for this interface in the standard PPP MIBs. The ifIndex value for PPP interfaces is not the same for both proprietary and standard MIB tables pertaining to PPP interface. Therefore this value is provide to simply cross referencing standard PPP and proprietary PPP MIB information. |
| I32 jnxPppLinkConfigChapMinChallengeLength | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.8 | Integer32 | read-only | Minimum value of the CHAP authenticator challenge length value. This value is never greater than jnxPppLinkConfigChapMaxChallengeLength. |
| I32 jnxPppLinkConfigChapMaxChallengeLength | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.9 | Integer32 | read-only | Maximum value of the CHAP authenticator challenge length value. This value is never less than jnxPppLinkConfigChapMinChallengeLength. |
| INT jnxPppLinkConfigPassiveMode | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.10 | INTEGER | read-only | When enabled, LCP state machine is forced into passive mode on lower layer UP message. It adds compatibility with slow and buggy clients. |
| OCT jnxPppLinkConfigAuthenticatorLogicalSystem | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.11 | OCTET STRING | read-only | The name of the logical system to be used for authentication on the PPP interface.With READ-CREATE maximum access , setting this object statically binds the authenticating logical system with the PPP interface. If this object is not explicitly set or it is set to null string, then this object is ignored and the virtual router used for authentication is determined by other means. On a Set operation, if the value of this object is not null and does not correspond to an existing virtual router, then an inconsistentValue error is returned. Setting this object to a non-null string returns inconsistentValue error if jnxPppLinkConfigAuthentication object is none(0) or not configured. |
| OCT jnxPppLinkConfigAuthenticatorRoutingInstance | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.12 | OCTET STRING | read-only | The name of the routing instancebe used for authentication on the PPP interface. With READ-CREATE maximum access, setting this object statically binds the authenticating routing instance with the PPP interface.If this object is not explicitly set or it is set to null string, then this object is ignored and the virtual router used for authentication is determined by other means. On a Set operation, if the value of this object is not null and does not correspond to an existing virtual router, then an inconsistentValue error is returned. Setting this object to a non-null string returns inconsistentValue error if jnxPppLinkConfigAuthentication object is none(0) or not configured. |
| OCT jnxPppLinkConfigAaaProfile | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.13 | OCTET STRING | read-only | The name of the AAA profile to be used for authentication on the PPP interface. With READ-CREATE maximum access, setting this object statically binds the AAA profile with the PPP interface. If this object is not explicitly set or it is set to null string, then this object is ignored. On a Set operation, if the value of this object is not null and does not correspond to an existing AAA profile, then an inconsistentValue error is returned. |
| JNX jnxPppLinkConfigAuthentication2 | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.14 | JnxNibbleConfig | read-only | A configuration variable comprised of nibbles i.e. 4 bits, such that a client can supply a list of 0 to 8 selections. The least significant nibble is the first value of the list, and the most significant nibble is the last value. The value in each field ranges from 0 to 15, however the first nibble with value 0 indicates the end of the list. Repetition of values is not allowed. Segregation of values is not allowed. Valid Values are: none - 0 pap - 1 chap - 2 eap - 3 Example valid encoding: 0x00000321 0x00000012 Not a valid encoding: 0x00000121 0x01002001 If authentication negotiation is not supported for this PPP interface and with READ-CREATE maximum access ,any attempt to explicitly set this object will result in a notWritable error and it will be implicitly set to the DEFVAL on row creation. Setting this object to null will set jnxPppLinkConfigAuthenticatorRoutingInstance object to an empty string. Setting this object along with the jnxPppLinkConfigAuthentication object will return an inconsistentValue error. |
| INT jnxPppLinkConfigIgnoreMagicNumberMismatch | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.15 | INTEGER | read-only | The ignore magic number mismatch option of the PPP interface determines the action to be taken, when the peer has not negotiated any value yet sent null or invalid magic number in the LCP echo packets. The two actions that can be configured are: 1) Ignore the mismatch and retain connection 2) Disallow the mismatch and terminate connection |
| I32 jnxPppLinkConfigMaxLcpRenegotiation | 1.3.6.1.4.1.2636.3.68.1.1.1.2.1.16 | Integer32 | read-only | Maximum number of allowed lcp renegotiation attempts from peer. |
| NUM jnxPppNextIfIndex | 1.3.6.1.4.1.2636.3.68.1.1.1.3 | InterfaceIndexOrZero | read-only | Coordinate ifIndex value allocation for entries in the jnxPppLinkConfigTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available.This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously. |
| jnxPppSec | 1.3.6.1.4.1.2636.3.68.1.1.2 | |||
| jnxPppIp | 1.3.6.1.4.1.2636.3.68.1.1.3 | |||
| jnxPppIpTable | 1.3.6.1.4.1.2636.3.68.1.1.3.1 | not-accessible | Table containing the IP parameters for the local PPP entity. | |
| jnxPppIpEntry | 1.3.6.1.4.1.2636.3.68.1.1.3.1.1 | not-accessible | IPCP status information for a particular PPP link. | |
| INT jnxPppIpServiceStatus | 1.3.6.1.4.1.2636.3.68.1.1.3.1.1.1 | INTEGER | read-only | Indicates whether IP protocol service is operating over this PPP link. Service is established on this link through means outside this MIB. |
| INT jnxPppIpTerminateReason | 1.3.6.1.4.1.2636.3.68.1.1.3.1.1.2 | INTEGER | read-only | Reason the IPCP link was terminated: none None. other Not specified. noService No IP service configured on this PPP link. admin Administratively disabled. linkDown Underlying link is down. peerTerminated Peer initiated termination. peerRenegotiated Peer initiated renegotiation. maxRetriesExceeded Maximum number of config retries exceeded. negotiationFailure Failed to negotiate IPCP option. See jnxPppIpTerminateNegFailOption. |
| INT jnxPppIpTerminateNegFailOption | 1.3.6.1.4.1.2636.3.68.1.1.3.1.1.3 | INTEGER | read-only | Reports the PPP IPCP option for which negotiation failed, when jnxPppIpTerminateReason has the value 'negotiationFailure'. |
| IP jnxPppIpLocalIpAddress | 1.3.6.1.4.1.2636.3.68.1.1.3.1.1.4 | IpAddress | read-only | IP Address used by the local side. |
| IP jnxPppIpRemoteIpAddress | 1.3.6.1.4.1.2636.3.68.1.1.3.1.1.5 | IpAddress | read-only | IP Address used by the remote side. |
| IP jnxPppIpRemotePrimaryDnsAddress | 1.3.6.1.4.1.2636.3.68.1.1.3.1.1.6 | IpAddress | read-only | Primary DNS server used by the remote side. |
| IP jnxPppIpRemoteSecondaryDnsAddress | 1.3.6.1.4.1.2636.3.68.1.1.3.1.1.7 | IpAddress | read-only | Secondary DNS server used by the remote side. |
| IP jnxPppIpRemotePrimaryWinsAddress | 1.3.6.1.4.1.2636.3.68.1.1.3.1.1.8 | IpAddress | read-only | Primary WINS server used by the remote side. |
| IP jnxPppIpRemoteSecondaryWinsAddress | 1.3.6.1.4.1.2636.3.68.1.1.3.1.1.9 | IpAddress | read-only | Secondary WINS server used by the remote side. |
| C32 jnxPppIpNetworkStatusIpcpRenegoTerminates | 1.3.6.1.4.1.2636.3.68.1.1.3.1.1.10 | Counter32 | read-only | Number of times ipcp terminated due to peer exceeding max renegotiation attempts. |
| jnxPppIpConfigTable | 1.3.6.1.4.1.2636.3.68.1.1.3.2 | not-accessible | Table containing the IP parameters for the local PPP entity. | |
| jnxPppIpConfigEntry | 1.3.6.1.4.1.2636.3.68.1.1.3.2.1 | not-accessible | IPCP configuration information for a particular PPP link. | |
| INT jnxPppIpConfigPeerDnsPriority | 1.3.6.1.4.1.2636.3.68.1.1.3.2.1.1 | INTEGER | read-only | When enabled, allows peer's DNS address to prevail in the event of a negotiation conflict; when disabled, the local PPP interface's DNS address prevails. |
| INT jnxPppIpConfigPeerWinsPriority | 1.3.6.1.4.1.2636.3.68.1.1.3.2.1.2 | INTEGER | read-only | When enabled, allows peer's WINS address to prevail in the event of a negotiation conflict; when disabled, the local PPP interface's WINS address prevails. |
| INT jnxPppIpConfigIpcpNetmask | 1.3.6.1.4.1.2636.3.68.1.1.3.2.1.3 | INTEGER | read-only | Enables the negotiation of the IPCP option netmask (0x90) during IPCP negotiation. |
| INT jnxPppIpConfigInitiateIp | 1.3.6.1.4.1.2636.3.68.1.1.3.2.1.4 | INTEGER | read-only | Enables the initiation of negotiation of the IPCP. |
| I32 jnxPppIpConfigMaxIpcpRenegotiation | 1.3.6.1.4.1.2636.3.68.1.1.3.2.1.5 | Integer32 | read-only | Maximum number of allowed ipcp renegotiation attempts from peer. |
| INT jnxPppIpConfigPromptIpcpDnsOption | 1.3.6.1.4.1.2636.3.68.1.1.3.2.1.6 | INTEGER | read-only | Control prompting of IPCP DNS option to remote peer. |
| INT jnxPppIpConfigIpcpLockout | 1.3.6.1.4.1.2636.3.68.1.1.3.2.1.7 | INTEGER | read-only | Enables IPCP lockout. It determines whether this NCP can be negotiated when the interface is already running a different NCP. On enabling this option, the IPCP negotiation will be blocked after a different NCP service is up and waited for 10 seconds for IPCP initiation from peer. |
| jnxPppOsi | 1.3.6.1.4.1.2636.3.68.1.1.4 | |||
| jnxPppOsiTable | 1.3.6.1.4.1.2636.3.68.1.1.4.1 | not-accessible | Table containing the OSI parameters for the local PPP entity. | |
| jnxPppOsiEntry | 1.3.6.1.4.1.2636.3.68.1.1.4.1.1 | not-accessible | OSICP status information for a particular PPP link. | |
| INT jnxPppOsiServiceStatus | 1.3.6.1.4.1.2636.3.68.1.1.4.1.1.1 | INTEGER | read-only | Indicates whether OSI protocol service is operating over this PPP link. Service is established on this link through means outside this MIB. |
| INT jnxPppOsiOperStatus | 1.3.6.1.4.1.2636.3.68.1.1.4.1.1.2 | INTEGER | read-only | The operational status of the OSI network protocol. If the value of this object is up then the finite state machine for the OSI network protocol has reached the Opened state. |
| INT jnxPppOsiTerminateReason | 1.3.6.1.4.1.2636.3.68.1.1.4.1.1.3 | INTEGER | read-only | Reason the OSICP link was terminated: none None. other Not specified. noService No OSI service configured on this PPP link. admin Administratively disabled. linkDown Underlying link is down. peerTerminated Peer initiated termination. peerRenegotiated Peer initiated renegotiation. maxRetriesExceeded Maximum number of config retries exceeded. negotiationFailure Failed to negotiate IPCP option. See jnxPppOsiTerminateNegFailOption. |
| INT jnxPppOsiTerminateNegFailOption | 1.3.6.1.4.1.2636.3.68.1.1.4.1.1.4 | INTEGER | read-only | Reports the PPP OSICP option for which negotiation failed, when jnxPppOsiTerminateReason has the value 'negotiationFailure'. |
| INT jnxPppOsiLocalAlignNpdu | 1.3.6.1.4.1.2636.3.68.1.1.4.1.1.5 | INTEGER | read-only | Local alignment of network PDU: none No alignment specified. oneModulo4 Alignment on first octet (out of four). twoModulo4 Alignment on second octet (out of four). threeModulo4 Alignment on third octet (out of four). fourModulo4 Alignment on fourth octet (out of four). even Alignment on even-octet boundary. odd Alignment on odd-octet boundary. |
| INT jnxPppOsiRemoteAlignNpdu | 1.3.6.1.4.1.2636.3.68.1.1.4.1.1.6 | INTEGER | read-only | Remote alignment of network PDU. none No alignment specified. oneModulo4 Alignment on first octet (out of four). twoModulo4 Alignment on second octet (out of four). threeModulo4 Alignment on third octet (out of four). fourModulo4 Alignment on fourth octet (out of four). even Alignment on even-octet boundary. odd Alignment on odd-octet boundary. |
| jnxPppOsiConfigTable | 1.3.6.1.4.1.2636.3.68.1.1.4.2 | not-accessible | Table containing configuration variables for the OSICP for the local PPP entity. | |
| jnxPppOsiConfigEntry | 1.3.6.1.4.1.2636.3.68.1.1.4.2.1 | not-accessible | OSICP information for a particular PPP link. | |
| INT jnxPppOsiConfigAdminStatus | 1.3.6.1.4.1.2636.3.68.1.1.4.2.1.1 | INTEGER | read-only | The immediate desired status of the OSI network protocol. Setting this object to open will inject an administrative open event into the OSI network protocol's finite state machine. Setting this object to close will inject an administrative close event into the OSI network protocol's finite state machine. |
| jnxPppSession | 1.3.6.1.4.1.2636.3.68.1.1.5 | |||
| jnxPppSessionTable | 1.3.6.1.4.1.2636.3.68.1.1.5.1 | not-accessible | This table contains entries for PPP interfaces present in the system. | |
| jnxPppSessionEntry | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1 | not-accessible | Each entry describes the characteristics of a PPP interface. | |
| T/F jnxPppSessionGrant | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.1 | TruthValue | read-only | Indicates whether a session has been granted via the authentication mechanism. |
| INT jnxPppSessionTerminateReason | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.2 | INTEGER | read-only | The reason the session was terminated. |
| TIK jnxPppSessionStartTime | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.3 | TimeTicks | read-only | The value of sysUpTime when this session last became active. |
| C32 jnxPppSessionInOctets | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.4 | Counter32 | read-only | Number of octets received since this session last became active, as denoted by jnxPppSessionStartTime. This has been deprecated and replaced by jnxPppSessionInOctets64 |
| C32 jnxPppSessionOutOctets | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.5 | Counter32 | read-only | Number of octets sent since this session last became active, as denoted by jnxPppSessionStartTime. This has been deprecated and replaced by jnxPppSessionOutOctets64 |
| C32 jnxPppSessionInPackets | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.6 | Counter32 | read-only | Number of packets received since this session last became active, as denoted by jnxPppSessionStartTime. This has been deprecated and replaced by jnxPppSessionInPackets64 |
| C32 jnxPppSessionOutPackets | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.7 | Counter32 | read-only | Number of packets sent since this session last became active, as denoted by jnxPppSessionStartTime. This has been deprecated and replaced by jnxPppSessionOutPackets64 |
| I32 jnxPppSessionSessionTimeout | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.8 | Integer32 | read-only | Maximum duration for the session, after which the session terminates automatically. |
| I32 jnxPppSessionInactivityTimeout | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.9 | Integer32 | read-only | Maximum inactivity duration for the session, after which the session terminates automatically. |
| I32 jnxPppSessionAccountingInterval | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.10 | Integer32 | read-only | Interval that must elapse between generation of accounting records for this session. |
| IP jnxPppSessionRemoteIpAddress | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.11 | IpAddress | read-only | Remote IP address, obtained from the authentication service, to be used during IPCP negotiation with the remote side. |
| IP jnxPppSessionRemotePrimaryDnsAddress | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.12 | IpAddress | read-only | Remote primary DNS IP address, obtained from the authentication service, to be used during IPCP negotiation with the remote side. |
| IP jnxPppSessionRemoteSecondaryDnsAddress | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.13 | IpAddress | read-only | Remote secondary DNS IP address, obtained from the authentication service, to be used during IPCP negotiation with the remote side. |
| IP jnxPppSessionRemotePrimaryWinsAddress | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.14 | IpAddress | read-only | Remote primary WINS IP address, obtained from the authentication service, to be used during IPCP negotiation with the remote side. |
| IP jnxPppSessionRemoteSecondaryWinsAddress | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.15 | IpAddress | read-only | Remote secondary WINS IP address, obtained from the authentication service, to be used during IPCP negotiation with the remote side. |
| ADR jnxPppSessionRemoteIpv6AddressIfIdentifier | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.16 | Ipv6AddressIfIdentifier | read-only | IPV6 Address Interface Identifier obtained from the authentication service, to be used during IPCP negotiation with the remote side. |
| INT jnxPppSessionInhibitIp | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.17 | INTEGER | read-only | Indicates whether a session has had its IP service inhibited by the authentication mechanism. |
| INT jnxPppSessionInhibitIpv6 | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.18 | INTEGER | read-only | Indicates whether a session has had its IPv6 service inhibited by the authentication mechanism. |
| C64 jnxPppSessionInOctets64 | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.19 | Counter64 | read-only | Number of octets received since this session last became active, as denoted by jnxPppSessionStartTime. |
| C64 jnxPppSessionOutOctets64 | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.20 | Counter64 | read-only | Number of octets sent since this session last became active, as denoted by jnxPppSessionStartTime. |
| C64 jnxPppSessionInPackets64 | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.21 | Counter64 | read-only | Number of packets received since this session last became active, as denoted by jnxPppSessionStartTime. |
| C64 jnxPppSessionOutPackets64 | 1.3.6.1.4.1.2636.3.68.1.1.5.1.1.22 | Counter64 | read-only | Number of packets sent since this session last became active, as denoted by jnxPppSessionStartTime. |
| jnxPppMlPpp | 1.3.6.1.4.1.2636.3.68.1.1.6 | |||
| jnxPppMlPppBundleTable | 1.3.6.1.4.1.2636.3.68.1.1.6.1 | not-accessible | This table contains entries for MLPPP bundles present in the system. | |
| jnxPppMlPppBundleEntry | 1.3.6.1.4.1.2636.3.68.1.1.6.1.1 | not-accessible | Each entry describes the characteristics of a MLPPP bundle. | |
| JNX jnxPppMlPppBundleName | 1.3.6.1.4.1.2636.3.68.1.1.6.1.1.1 | JnxPppMlPppBundleName | not-accessible | The administrative name of the MLPPP bundle associated with this MLPPP network interface. |
| ROW jnxPppMlPppBundleRowStatus | 1.3.6.1.4.1.2636.3.68.1.1.6.1.1.2 | RowStatus | read-only | The rowStatus for this entry. The following sets are supported with read-create maximum access: createAndGo(4), destroy(6) The following values can be read from this object: active(1) |
| NUM jnxPppMlPppBundleNetworkIfIndex | 1.3.6.1.4.1.2636.3.68.1.1.6.1.1.3 | InterfaceIndex | read-only | The ifIndex of this MLPPP network interface. It is a valid ifIndex even if there is no corresponding network interface instance in the jnxPppMlPppLinkConfigTable. |
| NUM jnxPppMlPppNextLinkIfIndex | 1.3.6.1.4.1.2636.3.68.1.1.6.2 | InterfaceIndexOrZero | read-only | Coordinate ifIndex value allocation for entries in jnxPppMlPppLinkConfigTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously. |
| jnxPppMlPppLinkConfigTable | 1.3.6.1.4.1.2636.3.68.1.1.6.3 | not-accessible | This table contains entries for MLPPP interfaces present in the system. | |
| jnxPppMlPppLinkConfigEntry | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1 | not-accessible | Each entry describes the characteristics of MLPPP interface. With read-create maximum access,creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/jnxIfTable. | |
| NUM jnxPppMlPppLinkConfigIfIndex | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.1 | InterfaceIndex | not-accessible | The ifIndex of the MLPPP interface. When creating entries in this table, suitable values for this object are determined by reading jnxPppMlPppNextLinkIfIndex. |
| NUM jnxPppMlPppLinkConfigLowerIfIndex | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.2 | InterfaceIndexOrZero | read-only | The ifIndex of an interface over which this PPP interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a non-zero value be configured at entry creation. |
| I32 jnxPppMlPppLinkConfigKeepalive | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.4 | Integer32 | read-only | Keepalive interval in seconds. A value of zero disables keepalive. Keepalive is performed using LCP Echo. |
| JNX jnxPppMlPppLinkConfigAuthentication | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.5 | JnxPppAuthentication | read-only | Specifies the type(s) of authentication, if any, to be negotiated with the peer: none No authentication is negotiated. pap PAP negotiation only. chap CHAP negotiation only. papChap PAP negotiation is attempted first; if fails, attempt CHAP. chapPap CHAP negotiation is attempted first; if fails, attempt PAP. If authentication negotiation is not supported for this MLPPP interface, then any attempt to explicitely set this object will result in a notWritable error and it will be implicitily set to the DEFVAL on row creation. This object returns a none (0) value on the get operation. New object jnxPppMlPppLinkConfigAuthentication2 will reflect the configured values. Setting this object along with the jnxPppMlPppLinkConfigAuthentication2 object will return an inconsistentValue error. |
| I32 jnxPppMlPppLinkConfigMaxAuthenRetries | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.6 | Integer32 | read-only | The number of authentication retries permitted, in addition to a failed initial attempt. If all retries fail, the link is reset. |
| ROW jnxPppMlPppLinkConfigRowStatus | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.7 | RowStatus | read-only | Controls creation/deletion of entries in this table with read-carete maximum access,according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: jnxPppMlPppLinkConfigRowStatus jnxPppMlPppLinkConfigLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for jnxPppMlPppLinkConfigIndex must have been determined previously, by reading jnxPppMlPppNextIfIndex. The interface identified by jnxPppMlPppLinkConfigLowerIfIndex must exist. A corresponding entry in ifTable/ifXTable/jnxIfTable is created/destroyed as a result of creating/destroying an entry in this table. The following values can be read from this object: active(1) |
| OCT jnxPppMlPppLinkConfigAaaProfile | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.8 | OCTET STRING | read-only | The name of the AAA profile to be used for authentication on the PPP interface.Setting this object statically binds the AAA profile with the PPP interface. If this object is not explicitly set or it is set to null string, then this object is ignored. On a Set operation, if the value of this object is not null and does not correspond to an existin AAA profile, then an inconsistentValue error is returned. |
| I32 jnxPppMlPppLinkConfigChapMinChallengeLength | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.9 | Integer32 | read-only | Minimum value of the CHAP authenticator challenge length value. This value is never allowed to be set to a value greater than jnxPppMlPppLinkConfigChapMaxChallengeLength. |
| I32 jnxPppMlPppLinkConfigChapMaxChallengeLength | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.10 | Integer32 | read-only | Maximum value of the CHAP authenticator challenge length value. |
| INT jnxPppMlPppLinkConfigPassiveMode | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.11 | INTEGER | read-only | When enabled, LCP state machine is forced into passive mode on lower layer UP message. It adds compatibility with slow and buggy clients. |
| OCT jnxPppMlPppLinkConfigAuthenticatorLogicalSystem | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.12 | OCTET STRING | read-only | The name of the Logical System (Jnxper-ROUTER-MIB.jnxRouterName) to be used for authentication on the PPP interface. Setting this object statically binds the authenticating virtual router with the link interface. With read-create maximum access, if this object is not explicitly set or it is set to null string, then this object is ignored and the virtual router used for authentication is determined by other means. On a Set operation, if the value of this object is not null and does not correspond to an existing virtual router, then an inconsistentValue error is returned. |
| OCT jnxPppMlPppLinkConfigAuthenticatorRoutingInstance | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.13 | OCTET STRING | read-only | The name of the Routing Instance (Jnxper-ROUTER-MIB.jnxRouterName) to be used for authentication on the PPP interface. Setting this object statically binds the authenticating virtual router with the link interface. With read-create maximum access, if this object is not explicitly set or it is set to null string, then this object is ignored and the virtual router used for authentication is determined by other means. On a Set operation, if the value of this object is not null and does not correspond to an existing virtual router, then an inconsistentValue error is returned. |
| INT jnxPppMlPppLinkConfigFragmentation | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.14 | INTEGER | read-only | Enables MLPPP fragmentation.With read-create maximum access, changing this object has an effect when the link is next restarted. |
| INT jnxPppMlPppLinkConfigReassembly | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.15 | INTEGER | read-only | Enables MLPPP reassembly. With read-create maximum access, changing this object has an effect when the link is next restarted. |
| I32 jnxPppMlPppLinkConfigMaxReceiveReconstructedUnit | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.16 | Integer32 | read-only | The Maximum Receive Reconstructed Unit (MRRU) that the local PPP entity will advertise to the remote entity. If the value of this variable is 1, then the MRRU is set to the local MRU value. With read-create maximum access, changing this object has an effect when the link is next restarted. |
| I32 jnxPppMlPppLinkConfigFragmentSize | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.17 | Integer32 | read-only | The size of fragments transmitted by the local PPP entity. If the value of this variable is 1, then the fragment size is set to the link's MTU value. With read-create maximum access, changing this object has an effect when the link is next restarted. |
| INT jnxPppMlPppLinkConfigHashLinkSelection | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.18 | INTEGER | read-only | Enables MLPPP hash-based link selection for non-best-effort traffic. With read-create maximum access,changing this object has an effect when the link is next restarted. |
| JNX jnxPppMlPppLinkConfigAuthentication2 | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.19 | JnxNibbleConfig | read-only | A configuration variable comprised of nibbles i.e. 4 bits, such that a client can supply a list of 0 to 8 selections. The least significant nibble is the first value of the list, and the most significant nibble is the last value. The value in each field ranges from 0 to 15, however the first nibble with value 0 indicates the end of the list. Repetition of values is not allowed. Segregation of values is not allowed. Valid Values are: none - 0 pap - 1 chap - 2 eap - 3 Example valid encoding: 0x00000321 0x00000012 Not a valid encoding: 0x00000121 0x01002001 If authentication negotiation is not supported for this PPP interface and With read-create maximum access, then any attempt to explicitly set this object will result in a notWritable error and it will be implicitly set to the DEFVAL on row creation. Setting this object to null will set jnxPppMlPppLinkConfigAuthenticatorVirtualRouter object to an empty string.Setting this object along with the jnxPppMlPppLinkConfigAuthentication object will return an i nconsistentValue error. |
| INT jnxPppMlPppLinkConfigIgnoreMagicNumberMismatch | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.20 | INTEGER | read-only | The ignore magic number mismatch option of the PPP interface determines the action to be taken, when the peer has not negotiated any value yet sent null or invalid magic number in the LCP echo packets. The two actions that can be configured are: 1) Ignore the mismatch and retain connection 2) Disallow the mismatch and terminate connection |
| INT jnxPppMlPppLinkConfigMultilinkMulticlass | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.21 | INTEGER | read-only | Enables Multiclass Multilink PPP (MCML). With read-create maximum access,changing this object has an effect when the link is next restarted. |
| INT jnxPppMlPppLinkConfigMultilinkMaxMultiClasses | 1.3.6.1.4.1.2636.3.68.1.1.6.3.1.22 | INTEGER | read-only | Maximum number of MCML classes to be negotiated.With read-create maximum access,changing this object has an effect when the link is next restarted. |
| NUM jnxPppMlPppNextNetworkIfIndex | 1.3.6.1.4.1.2636.3.68.1.1.6.4 | InterfaceIndexOrZero | read-only | Coordinate ifIndex value allocation for entries in jnxPppMlPppNetworkConfigTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously. |
| jnxPppMlPppNetworkConfigTable | 1.3.6.1.4.1.2636.3.68.1.1.6.5 | not-accessible | This table contains entries for MLPPP network interfaces present in the system. | |
| jnxPppMlPppNetworkConfigEntry | 1.3.6.1.4.1.2636.3.68.1.1.6.5.1 | not-accessible | Each entry describes the characteristics of MLPPP interface. With read-create maximum access,creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/jnxIfTable. | |
| NUM jnxPppMlPppNetworkConfigIfIndex | 1.3.6.1.4.1.2636.3.68.1.1.6.5.1.1 | InterfaceIndex | not-accessible | The ifIndex of the MLPPP network interface. When creating entries in this table, suitable values for this object are determined by reading jnxPppMlPppNextNetworkIfIndex. |
| NUM jnxPppMlPppNetworkConfigLowerIfIndex | 1.3.6.1.4.1.2636.3.68.1.1.6.5.1.2 | InterfaceIndex | read-only | The ifIndex of a PPP link interface over which this PPP network interface is to be layered. On sets, the value of this object must equal on of the previously created PPP link interfaces created in the jnxPppMlPppLinkConfigTable. On gets, the value of this object is the lexicographically least PPP link interface in a potential bundle of PPP link interfaces. |
| JNX jnxPppMlPppNetworkBundleName | 1.3.6.1.4.1.2636.3.68.1.1.6.5.1.3 | JnxPppMlPppBundleName | read-only | The MLPPP bundle name administratively assigned. |
| ROW jnxPppMlPppNetworkRowStatus | 1.3.6.1.4.1.2636.3.68.1.1.6.5.1.4 | RowStatus | read-only | Controls creation/deletion of entries in this table with read-create maximum access , according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: jnxPppMlPppNetworkConfigLowerIfIndex jnxPppMlPppNetworkBundleName jnxPppMlPppNetworkConfigRowStatus In addition, when creating an entry the following conditions must hold: A value for jnxPppMlPppNetworkConfigIndex must have been determined previously, by reading jnxPppMlPppNextNetworkIfIndex. The interface identified by jnxPppMlPppNetworkConfigLowerIfInde must exist by a creation request to the jnxPppMlPppLinkConfigTable. The bundleName specified in jnxPppMlPppNetworkBundleName must have been created first in the jnxPppMlPppBundleTable. A corresponding entry in ifTable/ifXTable/jnxIfTable is created/destroyed as a result of creating/destroying an entry in this table. The following values can be read from this object: active(1) |
| jnxPppMlPppLinkBindTable | 1.3.6.1.4.1.2636.3.68.1.1.6.6 | not-accessible | This table contains entries for MLPPP Link interface to MLPPP network interfaces bindings. | |
| jnxPppMlPppLinkBindEntry | 1.3.6.1.4.1.2636.3.68.1.1.6.6.1 | not-accessible | Each entry describes the MLPPP link interface to MLPPP network interface bindings. | |
| NUM jnxPppMlPppBindNetworkIfIndex | 1.3.6.1.4.1.2636.3.68.1.1.6.6.1.1 | InterfaceIndex | not-accessible | The ifIndex of the MLPPP network interface. |
| NUM jnxPppMlPppBindLinkIfIndex | 1.3.6.1.4.1.2636.3.68.1.1.6.6.1.2 | InterfaceIndex | not-accessible | The ifIndex of a MLPPP link interface bound by the MLPPP network interface defined by jnxPppMlPppBindNetworkIfIndex. |
| ROW jnxPppMlPppBindRowStatus | 1.3.6.1.4.1.2636.3.68.1.1.6.6.1.3 | RowStatus | read-only | Controls creation/deletion of entries in this table with read-create maximum access, according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: jnxPppMlPppBindRowStatus In addition, when creating an entry the following conditions must hold: The interfaces identified by jnxPppMlPppBindNetworkIfIndex and jnxPppMlPppBindLinkIfIndex must be created in the jnxPppMlPppNetworkConfigTable and jnxPppMlPppLinkConfigTable respectively. A MLPPP bundle must be associated with the jnxPppMlPppNetworkIfIndex and exist in the jnxPppMibPppBundleTable. A corresponding entry in ifStackTable is created/destroyed as a result of creating/destroying an entry in this table. The following values can be read from this object: active(1) |
| jnxPppSummary | 1.3.6.1.4.1.2636.3.68.1.1.7 | |||
| I32 jnxPppSummaryPppInterfaceCount | 1.3.6.1.4.1.2636.3.68.1.1.7.1 | Integer32 | read-only | The total number of PPP interfaces configured in the system. |
| I32 jnxPppSummaryPppIpNCPs | 1.3.6.1.4.1.2636.3.68.1.1.7.2 | Integer32 | read-only | The total number IP NCPs configured in the system. |
| I32 jnxPppSummaryPppOsiNCPs | 1.3.6.1.4.1.2636.3.68.1.1.7.3 | Integer32 | read-only | The total number of OSI NCPs configured in the system. |
| I32 jnxPppSummaryPppIfAdminUp | 1.3.6.1.4.1.2636.3.68.1.1.7.4 | Integer32 | read-only | The total number of PPP interfaces in the system that are administratively configured to up(1). |
| I32 jnxPppSummaryPppIfAdminDown | 1.3.6.1.4.1.2636.3.68.1.1.7.5 | Integer32 | read-only | The total number of PPP interfaces in the system that are administrateively configued to down(2). |
| I32 jnxPppSummaryPppIfOperUp | 1.3.6.1.4.1.2636.3.68.1.1.7.7 | Integer32 | read-only | The total number of PPP interfaces in the system with an operational state of up(1). |
| I32 jnxPppSummaryPppIfOperDown | 1.3.6.1.4.1.2636.3.68.1.1.7.8 | Integer32 | read-only | The total number of PPP interfaces in the system with an operational state of down(2). |
| I32 jnxPppSummaryPppIfOperDormant | 1.3.6.1.4.1.2636.3.68.1.1.7.9 | Integer32 | read-only | The total number of PPP interfaces in the system with an operational state of dormant(5). |
| I32 jnxPppSummaryPppIfNotPresent | 1.3.6.1.4.1.2636.3.68.1.1.7.10 | Integer32 | read-only | The total number of PPP interfaces in the system with an operational state of notPresent(6). |
| I32 jnxPppSummaryPppIfLowerLayerDown | 1.3.6.1.4.1.2636.3.68.1.1.7.11 | Integer32 | read-only | The total number of PPP interfaces in the system with an operational state of lowerLayerDown(7). |
| I32 jnxPppSummaryPppIpNcpOpened | 1.3.6.1.4.1.2636.3.68.1.1.7.12 | Integer32 | read-only | The total number of PPP IP NCPs in the system with an operational state of opened(1). |
| I32 jnxPppSummaryPppIpNcpClosed | 1.3.6.1.4.1.2636.3.68.1.1.7.13 | Integer32 | read-only | The total number of PPP IP NCPs in the system with an operational state of not-opened(2). |
| I32 jnxPppSummaryPppOsiNcpOpened | 1.3.6.1.4.1.2636.3.68.1.1.7.14 | Integer32 | read-only | The total number of PPP OSI NCPs in the system with an operational state of opened. |
| I32 jnxPppSummaryPppOsiNcpClosed | 1.3.6.1.4.1.2636.3.68.1.1.7.15 | Integer32 | read-only | The total number of PPP OSI NCPs in the system with an operational state of closed. |
| TIK jnxPppSummaryPppIfLastChangeTime | 1.3.6.1.4.1.2636.3.68.1.1.7.16 | TimeTicks | read-only | The value of the sysUpTime at the time of the last PPP interface creation or deletion in the system. If the number of PPP interfaces has been unchanged since the last re-initialization of the system, then this object contains a zero value. |
| I32 jnxPppSummaryPppLinkInterfaceCount | 1.3.6.1.4.1.2636.3.68.1.1.7.17 | Integer32 | read-only | The total number of PPP Link interfaces configured in the system. |
| I32 jnxPppSummaryPppLinkIfAdminUp | 1.3.6.1.4.1.2636.3.68.1.1.7.18 | Integer32 | read-only | The total number of PPP Link interfaces in the system that are administratively configured to up(1). |
| I32 jnxPppSummaryPppLinkIfAdminDown | 1.3.6.1.4.1.2636.3.68.1.1.7.19 | Integer32 | read-only | The total number of PPP Link interfaces in the system that are administrateively configued to down(2). |
| I32 jnxPppSummaryPppLinkIfOperUp | 1.3.6.1.4.1.2636.3.68.1.1.7.20 | Integer32 | read-only | The total number of PPP Link interfaces in the system with an operational state of up(1). |
| I32 jnxPppSummaryPppLinkIfOperDown | 1.3.6.1.4.1.2636.3.68.1.1.7.21 | Integer32 | read-only | The total number of PPP Link interfaces in the system with an operational state of down(2). |
| I32 jnxPppSummaryPppLinkIfOperDormant | 1.3.6.1.4.1.2636.3.68.1.1.7.22 | Integer32 | read-only | The total number of PPP Link interfaces in the system with an operational state of dormant(5). |
| I32 jnxPppSummaryPppLinkIfNotPresent | 1.3.6.1.4.1.2636.3.68.1.1.7.23 | Integer32 | read-only | The total number of PPP link interfaces in the system with an operational state of notPresent(6). |
| I32 jnxPppSummaryPppLinkIfLowerLayerDown | 1.3.6.1.4.1.2636.3.68.1.1.7.24 | Integer32 | read-only | The total number of PPP Link interfaces in the system with an operational state of lowerLayerDown(7). |
| TIK jnxPppSummaryPppLinkIfLastChangeTime | 1.3.6.1.4.1.2636.3.68.1.1.7.25 | TimeTicks | read-only | The value of the sysUpTime at the time of the last PPP Link interface creation or deletion in the system. If the number of PPP interfaces has been unchanged since the last re-initialization of the system, then this object contains a zero value. |
| I32 jnxPppSummaryPppNetworkInterfaceCount | 1.3.6.1.4.1.2636.3.68.1.1.7.26 | Integer32 | read-only | The total number of PPP network interfaces configured in the system. |
| I32 jnxPppSummaryPppNetworkIpNCPs | 1.3.6.1.4.1.2636.3.68.1.1.7.27 | Integer32 | read-only | The total number IP NCPs in the system configured on PPP network interfaces. |
| I32 jnxPppSummaryPppNetworkOsiNCPs | 1.3.6.1.4.1.2636.3.68.1.1.7.28 | Integer32 | read-only | The total number of OSI NCPs in the system configured on PPP network interfaces. |
| I32 jnxPppSummaryPppNetworkIfAdminUp | 1.3.6.1.4.1.2636.3.68.1.1.7.29 | Integer32 | read-only | The total number of PPP network interfaces in the system that are administratively configured to up(1). |
| I32 jnxPppSummaryPppNetworkIfAdminDown | 1.3.6.1.4.1.2636.3.68.1.1.7.30 | Integer32 | read-only | The total number of PPP network interfaces in the system that are administrateively configued to down(2). |
| I32 jnxPppSummaryPppNetworkIfOperUp | 1.3.6.1.4.1.2636.3.68.1.1.7.31 | Integer32 | read-only | The total number of PPP network interfaces in the system with an operational state of up(1). |
| I32 jnxPppSummaryPppNetworkIfOperDown | 1.3.6.1.4.1.2636.3.68.1.1.7.32 | Integer32 | read-only | The total number of PPP network interfaces in the system with an operational state of down(2). |
| I32 jnxPppSummaryPppNetworkIfOperDormant | 1.3.6.1.4.1.2636.3.68.1.1.7.33 | Integer32 | read-only | The total number of PPP network interfaces in the system with an operational state of dormant(5). |
| I32 jnxPppSummaryPppNetworkIfNotPresent | 1.3.6.1.4.1.2636.3.68.1.1.7.34 | Integer32 | read-only | The total number of PPP network interfaces in the system with an operational state of notPresent(6). |
| I32 jnxPppSummaryPppNetworkIfLowerLayerDown | 1.3.6.1.4.1.2636.3.68.1.1.7.35 | Integer32 | read-only | The total number of PPP network interfaces in the system with an operational state of lowerLayerDown(7). |
| I32 jnxPppSummaryPppNetworkIpNcpOpened | 1.3.6.1.4.1.2636.3.68.1.1.7.36 | Integer32 | read-only | The total number of PPP IP NCPs in the system with an operational state of opened(1). |
| I32 jnxPppSummaryPppNetworkIpNcpClosed | 1.3.6.1.4.1.2636.3.68.1.1.7.37 | Integer32 | read-only | The total number of PPP IP NCPs in the system with an operational state of not-opened(2). |
| I32 jnxPppSummaryPppNetworkOsiNcpOpened | 1.3.6.1.4.1.2636.3.68.1.1.7.38 | Integer32 | read-only | The total number of PPP OSI NCPs in the system with an operational state of opened. |
| I32 jnxPppSummaryPppNetworkOsiNcpClosed | 1.3.6.1.4.1.2636.3.68.1.1.7.39 | Integer32 | read-only | The total number of PPP OSI NCPs in the system with an operational state of closed. |
| TIK jnxPppSummaryPppNetworkIfLastChangeTime | 1.3.6.1.4.1.2636.3.68.1.1.7.40 | TimeTicks | read-only | The value of the sysUpTime at the time of the last PPP network interface creation or deletion in the system. If the number of PPP network interfaces has been unchanged since the last re-initialization of the system, then this object contains a zero value. |
| I32 jnxPppSummaryPppIpv6NCPs | 1.3.6.1.4.1.2636.3.68.1.1.7.41 | Integer32 | read-only | The total number IPv6 NCPs configured in the system. |
| I32 jnxPppSummaryPppIpv6NcpOpened | 1.3.6.1.4.1.2636.3.68.1.1.7.42 | Integer32 | read-only | The total number of PPP IPv6 NCPs in the system with an operational state of opened(1). |
| I32 jnxPppSummaryPppIpv6NcpClosed | 1.3.6.1.4.1.2636.3.68.1.1.7.43 | Integer32 | read-only | The total number of PPP IPv6 NCPs in the system with an operational state of not-opened(2). |
| I32 jnxPppSummaryPppNetworkIpv6NCPs | 1.3.6.1.4.1.2636.3.68.1.1.7.44 | Integer32 | read-only | The total number IPv6 NCPs configured in the system. |
| I32 jnxPppSummaryPppNetworkIpv6NcpOpened | 1.3.6.1.4.1.2636.3.68.1.1.7.45 | Integer32 | read-only | The total number of PPP IPv6 NCPs in the system with an operational state of opened(1). |
| I32 jnxPppSummaryPppNetworkIpv6NcpClosed | 1.3.6.1.4.1.2636.3.68.1.1.7.46 | Integer32 | read-only | The total number of PPP IPv6 NCPs in the system with an operational state of not-opened(2). |
| I32 jnxPppSummaryPppStaticInterfaceCount | 1.3.6.1.4.1.2636.3.68.1.1.7.47 | Integer32 | read-only | The total number of static PPP interfaces configured in the system. |
| I32 jnxPppSummaryPppMplsNCPs | 1.3.6.1.4.1.2636.3.68.1.1.7.48 | Integer32 | read-only | The total number MPLS NCPs configured in the system. |
| I32 jnxPppSummaryPppIpAdminOpen | 1.3.6.1.4.1.2636.3.68.1.1.7.49 | Integer32 | read-only | The total number of IP NCPs in the system that are administratively configured to open(1). |
| I32 jnxPppSummaryPppIpAdminClose | 1.3.6.1.4.1.2636.3.68.1.1.7.50 | Integer32 | read-only | The total number of IP NCPs in the system that are administratively configured to close(2). |
| I32 jnxPppSummaryPppIpv6AdminOpen | 1.3.6.1.4.1.2636.3.68.1.1.7.51 | Integer32 | read-only | The total number of IPV6 NCPs in the system that are administratively configured to open(1). |
| I32 jnxPppSummaryPppIpv6AdminClose | 1.3.6.1.4.1.2636.3.68.1.1.7.52 | Integer32 | read-only | The total number of IPV6 NCPs in the system that are administratively configured to close(2). |
| I32 jnxPppSummaryPppOsiAdminOpen | 1.3.6.1.4.1.2636.3.68.1.1.7.53 | Integer32 | read-only | The total number of OSI NCPs in the system that are administratively configured to open(1). |
| I32 jnxPppSummaryPppOsiAdminClose | 1.3.6.1.4.1.2636.3.68.1.1.7.54 | Integer32 | read-only | The total number of OSI NCPs in the system that are administratively configured to close(2). |
| I32 jnxPppSummaryPppMplsAdminOpen | 1.3.6.1.4.1.2636.3.68.1.1.7.55 | Integer32 | read-only | The total number of MPLS NCPs in the system that are administratively configured to open(1). |
| I32 jnxPppSummaryPppMplsAdminClose | 1.3.6.1.4.1.2636.3.68.1.1.7.56 | Integer32 | read-only | The total number of MPLS NCPs in the system that are administratively configured to close(2). |
| I32 jnxPppSummaryPppIpNcpNotPresent | 1.3.6.1.4.1.2636.3.68.1.1.7.57 | Integer32 | read-only | The total number of PPP IP NCPs in the system with an operational state of notPresent(3). |
| I32 jnxPppSummaryPppIpNcpNoResources | 1.3.6.1.4.1.2636.3.68.1.1.7.58 | Integer32 | read-only | The total number of PPP IP NCPs in the system with an operational state of noResources(4). |
| I32 jnxPppSummaryPppIpv6NcpNotPresent | 1.3.6.1.4.1.2636.3.68.1.1.7.59 | Integer32 | read-only | The total number of PPP IPV6 NCPs in the system with an operational state of notPresent(3). |
| I32 jnxPppSummaryPppIpv6NcpNoResources | 1.3.6.1.4.1.2636.3.68.1.1.7.60 | Integer32 | read-only | The total number of PPP IPV6 NCPs in the system with an operational state of noResources(4). |
| I32 jnxPppSummaryPppOsiNcpNotPresent | 1.3.6.1.4.1.2636.3.68.1.1.7.61 | Integer32 | read-only | The total number of PPP OSI NCPs in the system with an operational state of notPresent(3). |
| I32 jnxPppSummaryPppOsiNcpNoResources | 1.3.6.1.4.1.2636.3.68.1.1.7.62 | Integer32 | read-only | The total number of PPP OSI NCPs in the system with an operational state of noResources(4). |
| I32 jnxPppSummaryPppMplsNcpOpened | 1.3.6.1.4.1.2636.3.68.1.1.7.63 | Integer32 | read-only | The total number of PPP MPLS NCPs in the system with an operational state of opened(1). |
| I32 jnxPppSummaryPppMplsNcpClosed | 1.3.6.1.4.1.2636.3.68.1.1.7.64 | Integer32 | read-only | The total number of PPP MPLS NCPs in the system with an operational state of not-opened(2). |
| I32 jnxPppSummaryPppMplsNcpNotPresent | 1.3.6.1.4.1.2636.3.68.1.1.7.65 | Integer32 | read-only | The total number of PPP MPLS NCPs in the system with an operational state of notPresent(3). |
| I32 jnxPppSummaryPppMplsNcpNoResources | 1.3.6.1.4.1.2636.3.68.1.1.7.66 | Integer32 | read-only | The total number of PPP MPLS NCPs in the system with an operational state of noResources(4). |
| I32 jnxPppSummaryPppLinkStaticInterfaceCount | 1.3.6.1.4.1.2636.3.68.1.1.7.67 | Integer32 | read-only | The total number of static PPP Link interfaces configured in the system. |
| I32 jnxPppSummaryPppNetworkStaticInterfaceCount | 1.3.6.1.4.1.2636.3.68.1.1.7.68 | Integer32 | read-only | The total number of static PPP network interfaces configured in the system. |
| I32 jnxPppSummaryPppNetworkMplsNCPs | 1.3.6.1.4.1.2636.3.68.1.1.7.69 | Integer32 | read-only | The total number of MPLS NCPs in the system configured on PPP network interfaces. |
| I32 jnxPppSummaryPppNetworkIpAdminOpen | 1.3.6.1.4.1.2636.3.68.1.1.7.70 | Integer32 | read-only | The total number of IP NCPs in the system configured on PPP network interfaces that are administratively configured to open(1). |
| I32 jnxPppSummaryPppNetworkIpAdminClose | 1.3.6.1.4.1.2636.3.68.1.1.7.71 | Integer32 | read-only | The total number of IP NCPs in the system configured on PPP network interfaces that are administratively configured to close(2). |
| I32 jnxPppSummaryPppNetworkIpv6AdminOpen | 1.3.6.1.4.1.2636.3.68.1.1.7.72 | Integer32 | read-only | The total number of IPV6 NCPs in the system configured on PPP network interfaces that are administratively configured to open(1). |
| I32 jnxPppSummaryPppNetworkIpv6AdminClose | 1.3.6.1.4.1.2636.3.68.1.1.7.73 | Integer32 | read-only | The total number of IPV6 NCPs in the system configured on PPP network interfaces that are administratively configured to close(2). |
| I32 jnxPppSummaryPppNetworkOsiAdminOpen | 1.3.6.1.4.1.2636.3.68.1.1.7.74 | Integer32 | read-only | The total number of OSI NCPs in the system configured on PPP network interfaces that are administratively configured to open(1). |
| I32 jnxPppSummaryPppNetworkOsiAdminClose | 1.3.6.1.4.1.2636.3.68.1.1.7.75 | Integer32 | read-only | The total number of OSI NCPs in the system configured on PPP network interfaces that are administratively configured to close(2). |
| I32 jnxPppSummaryPppNetworkMplsAdminOpen | 1.3.6.1.4.1.2636.3.68.1.1.7.76 | Integer32 | read-only | The total number of MPLS NCPs in the system configured on PPP network interfaces that are administratively configured to open(1). |
| I32 jnxPppSummaryPppNetworkMplsAdminClose | 1.3.6.1.4.1.2636.3.68.1.1.7.77 | Integer32 | read-only | The total number of MPLS NCPs in the system configured on PPP network interfaces that are administratively configured to close(2). |
| I32 jnxPppSummaryPppNetworkIpNcpNotPresent | 1.3.6.1.4.1.2636.3.68.1.1.7.78 | Integer32 | read-only | The total number of IP NCPs in the system configured on PPP network interfaces with an operational state of notPresent(3). |
| I32 jnxPppSummaryPppNetworkIpNcpNoResources | 1.3.6.1.4.1.2636.3.68.1.1.7.79 | Integer32 | read-only | The total number of IP NCPs in the system configured on PPP network interfaces with an operational state of noResources(4). |
| I32 jnxPppSummaryPppNetworkIpv6NcpNotPresent | 1.3.6.1.4.1.2636.3.68.1.1.7.80 | Integer32 | read-only | The total number of IPV6 NCPs in the system configured on PPP network interfaces with an operational state of notPresent(3). |
| I32 jnxPppSummaryPppNetworkIpv6NcpNoResources | 1.3.6.1.4.1.2636.3.68.1.1.7.81 | Integer32 | read-only | The total number of IPV6 NCPs in the system configured on PPP network interfaces with an operational state of noResources(4). |
| I32 jnxPppSummaryPppNetworkOsiNcpNotPresent | 1.3.6.1.4.1.2636.3.68.1.1.7.82 | Integer32 | read-only | The total number of OSI NCPs in the system configured on PPP network interfaces with an operational state of notPresent(3). |
| I32 jnxPppSummaryPppNetworkOsiNcpNoResources | 1.3.6.1.4.1.2636.3.68.1.1.7.83 | Integer32 | read-only | The total number of OSI NCPs in the system configured on PPP network interfaces with an operational state of noResources(4). |
| I32 jnxPppSummaryPppNetworkMplsNcpOpened | 1.3.6.1.4.1.2636.3.68.1.1.7.84 | Integer32 | read-only | The total number of MPLS NCPs in the system configured on PPP network interfaces with an operational state of opened(1). |
| I32 jnxPppSummaryPppNetworkMplsNcpClosed | 1.3.6.1.4.1.2636.3.68.1.1.7.85 | Integer32 | read-only | The total number of MPLS NCPs in the system configured on PPP network interfaces with an operational state of not-opened(2). |
| I32 jnxPppSummaryPppNetworkMplsNcpNotPresent | 1.3.6.1.4.1.2636.3.68.1.1.7.86 | Integer32 | read-only | The total number of MPLS NCPs in the system configured on PPP network interfaces with an operational state of notPresent(3). |
| I32 jnxPppSummaryPppNetworkMplsNcpNoResources | 1.3.6.1.4.1.2636.3.68.1.1.7.87 | Integer32 | read-only | The total number of MPLS NCPs in the system configured on PPP network interfaces with an operational state of noResources(4). |
| jnxPppIpv6 | 1.3.6.1.4.1.2636.3.68.1.1.8 | |||
| jnxPppIpv6Table | 1.3.6.1.4.1.2636.3.68.1.1.8.1 | not-accessible | Table containing the IPv6 parameters for the local PPP entity. | |
| jnxPppIpv6Entry | 1.3.6.1.4.1.2636.3.68.1.1.8.1.1 | not-accessible | IPV6CP status information for a particular PPP link. | |
| INT jnxPppIpv6ServiceStatus | 1.3.6.1.4.1.2636.3.68.1.1.8.1.1.1 | INTEGER | read-only | Indicates whether IPv6 protocol service is operating over this PPP link. Service is established on this link through means outside this MIB. |
| INT jnxPppIpv6OperStatus | 1.3.6.1.4.1.2636.3.68.1.1.8.1.1.2 | INTEGER | read-only | The operational status of the IPv6 network protocol. If the value of this object is up then the finite state machine for the IPv6 network protocol has reached the Opened state. |
| INT jnxPppIpv6TerminateReason | 1.3.6.1.4.1.2636.3.68.1.1.8.1.1.3 | INTEGER | read-only | Reason the IPV6CP link was terminated: none None. other Not specified. noService No IPv6 service configured on this PPP link. admin Administratively disabled. linkDown Underlying link is down. peerTerminated Peer initiated termination. peerRenegotiated Peer initiated renegotiation. maxRetriesExceeded Maximum number of config retries exceeded. negotiationFailure Failed to negotiate IPV6CP option. See jnxPppIpv6TerminateNegFailOption. |
| INT jnxPppIpv6TerminateNegFailOption | 1.3.6.1.4.1.2636.3.68.1.1.8.1.1.4 | INTEGER | read-only | Reports the PPP IPV6CP option for which negotiation failed, when jnxPppIpv6TerminateReason has the value 'negotiationFailure'. |
| ADR jnxPppIpv6LocalIpv6AddressIfIdentifier | 1.3.6.1.4.1.2636.3.68.1.1.8.1.1.5 | Ipv6AddressIfIdentifier | read-only | IPv6 Address Interface Identifier used by the local side. |
| ADR jnxPppIpv6RemoteIpv6AddressIfIdentifier | 1.3.6.1.4.1.2636.3.68.1.1.8.1.1.6 | Ipv6AddressIfIdentifier | read-only | IPv6 Address Interface Identifier used by the remote side. |
| C32 jnxPppIpv6NetworkStatusIpv6cpRenegoTerminates | 1.3.6.1.4.1.2636.3.68.1.1.8.1.1.7 | Counter32 | read-only | Number of times ipv6cp terminated due to peer exceeding max renegotiation attempts. |
| jnxPppIpv6ConfigTable | 1.3.6.1.4.1.2636.3.68.1.1.8.2 | not-accessible | Table containing the IPv6 parameters for the local PPP entity. | |
| jnxPppIpv6ConfigEntry | 1.3.6.1.4.1.2636.3.68.1.1.8.2.1 | not-accessible | IPV6CP configuration information for a particular PPP link. | |
| INT jnxPppIpv6ConfigAdminStatus | 1.3.6.1.4.1.2636.3.68.1.1.8.2.1.1 | INTEGER | read-only | The immediate desired status of the IPv6 network protocol. Setting this object to open will inject an administrative open event into the IPv6 network protocol's finite state machine. Setting this object to close will inject an administrative close event into the IPv6 network protocol's finite state machine. |
| INT jnxPppIpv6ConfigInitiateIpv6 | 1.3.6.1.4.1.2636.3.68.1.1.8.2.1.2 | INTEGER | read-only | Enables the initiation of negotiation of the IPv6CP. |
| I32 jnxPppIpv6ConfigMaxIpv6cpRenegotiation | 1.3.6.1.4.1.2636.3.68.1.1.8.2.1.3 | Integer32 | read-only | Maximum number of allowed ipv6cp renegotiation attempts from peer. |
| jnxPppGlobalConfig | 1.3.6.1.4.1.2636.3.68.1.1.9 | |||
| INT jnxPppPeerIpAddressOptional | 1.3.6.1.4.1.2636.3.68.1.1.9.1 | INTEGER | read-only | This option is used to ignore the conflicts between ppp client's requested IP address and radius/local pool returned address in server during IPNCP negotiation. Enabling this will ensure the IPNCP negotiation to succeed even though the client does not include IP address option in the IPNCP configure request. |
RFC description
Juniper Networks vendor-private MIB for Point-to-Point Protocol (PPP) management and monitoring.
Start monitoring Juniper Networks router (PPP WAN circuits) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.