HP-ICF-IP-ROUTING

All MIBs › HP-ICF-IP-ROUTING

Organization: HP Networking.

Last Updated: 2016-12-02

Category: IP and Core Protocols, Technology: Routing/L3, Vendor: HP/HPE

Description: HP ICF SNMP MIB for IP routing configuration and status on HP ProCurve Layer 3 switches, covering static routes and routing parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HP-ICF-IP-ROUTING?

HP-ICF-IP-ROUTING is an HP-proprietary (ICF) SNMP module for managing IP routing configuration and status on HP ProCurve Layer 3 switches, covering static routes and general IP routing parameters. No sample objects or descriptive module text beyond the brief summary were available, so specific table/column names cannot be confirmed, but by its stated purpose it is primarily a routing-configuration MIB. Its monitoring value would lie in confirming static route entries are correctly provisioned and, if status objects exist, whether configured routes are active, which reflects software/protocol-level routing health rather than physical hardware condition. It is a vendor-specific extension that would logically complement the standard IP-FORWARD-MIB/IP-MIB used elsewhere for routing table monitoring. It is deployed on HP ProCurve Layer 3 switches in enterprise campus or distribution-layer networks where static routing is configured alongside or instead of dynamic routing protocols. Network engineers evaluating or troubleshooting this functionality can download the HP-ICF-IP-ROUTING file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HP-ICF-IP-ROUTING. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP ProCurve Layer 3 switches

Monitoring Examples

No concrete sample objects were provided, so a specific polling walkthrough cannot be grounded in real names; in general, this module would be used to verify configured static routes and general IP routing parameters are provisioned as intended on an HP ProCurve Layer 3 switch, rather than to expose hardware counters or fault conditions.

What Can Be Monitored

static route configuration
IP routing parameter settings

Imported Objects

From HP-ICF-OID

hpSwitch

OBJECT-IDENTITY

From HP-ICF-TC

HpInetCidrRouteState

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressPrefixLength
InetAddressType

From IP-FORWARD-MIB

inetCidrRouteDestType	OBJECT-TYPE
inetCidrRouteEntry	OBJECT-TYPE
ipCidrRouteEntry	OBJECT-TYPE

From IP-MIB

ipDefaultRouterEntry	OBJECT-TYPE
ipv6RouterAdvertEntry	OBJECT-TYPE

From OSPF-MIB

Metric

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
PhysAddress
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using hpicfInetCidrNumRouteDestinations OID:

Select an HP ProCurve Layer 3 switch (static IP routing config) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hpicfInetCidrNumRouteDestinations into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the total number of destinations for a particular inetCidrRouteDestType. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
I32 hpicfArpAgingTime	1.3.6.1.4.1.11.2.14.11.5.1.15.1.6.1	Integer32	read-write	The timeout period in minutes for aging out an arp entry in the arp cache. Default value is 20 minutes. Allowable values for the HP implementation are 1-1440 and 0. The value of 0 indicates that an infinite ageout is to be used. The value 16666666 minutes (32 years) is used internally to effectively indicate an infinite timeout.
hpicfArpBaseGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.10			Basic ARP (address resolution protocol) configuration objects.
hpicfArpInfo	1.3.6.1.4.1.11.2.14.11.5.1.15.1.6
hpicfArpInfoCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.4			The compliance statement for HP Routing switches that support ARP.
INT hpicfArpMcastReplies	1.3.6.1.4.1.11.2.14.11.5.1.15.1.6.2	INTEGER	read-write	This object is used to enable/disable Multicast MAC support in all multicast modes. It will be disabled by default.
STR hpicfDBroadcastFwdAcl	1.3.6.1.4.1.11.2.14.11.5.1.15.1.3.4	SnmpAdminString	read-write	This object contains the ACL to apply to IP Directed Broadcast packets.The value is the name of an existing IP ACL defined using the Command Line Interface (CLI) or a zero length string if there is no ACL applied. This object can only be set when hpicfDBroadcastFwdEnable is also set to 'enable' in the same request. Setting hpicfBroadcastFwdEnable to 'enable' without also setting this object will clear this object and unapply any IP Directed Broadcast ACL.
hpicfDBroadcastFwdAclGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.25			The group member is used to configure name of ACL when it is applied to IP Directed Broadcast.
INT hpicfDBroadcastFwdEnable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.3.1	INTEGER	read-write	Enable/disable directed broadcast forwarding.
hpicfGlobalIpConfig	1.3.6.1.4.1.11.2.14.11.5.1.15.1.3
hpicfGlobalIpConfigCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.7			The compliance statement for HP Routing switches that support Router Advertisements.
hpicfGlobalIpConfigGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.13			The group of objects in a table hp BSD broadcast forwarding enable/disable flags.
INT hpicfIcmpAddrMaskReplyEnable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.2.1.5	INTEGER	read-write	Enable/Disable address mask replies.
hpicfIcmpBoxLimits	1.3.6.1.4.1.11.2.14.11.5.1.15.1.2.1
INT hpicfIcmpDestUnreachEnable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.2.1.4	INTEGER	read-write	Enable/Disable destination unreachable error messages.
INT hpicfIcmpEchoBroadcastReplyEnable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.2.1.6	INTEGER	read-write	Enable/Disable echo replies to directed broadcast echo requests..
hpicfIcmpRateLimits	1.3.6.1.4.1.11.2.14.11.5.1.15.1.2
hpicfIcmpRdisc	1.3.6.1.4.1.11.2.14.11.5.1.15.1.1
hpicfIcmpRdiscCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.1			The compliance statement for HP Routing switches that support ICMP Router Discovery.
INT hpicfIcmpRedirectEnable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.2.1.3	INTEGER	read-write	Enable/Disable redirect error messages..
hpicfIcmpReplyBaseGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.3			A collection of objects allowing configuration of ICMP Redirect operation.
hpicfIcmpReplyCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.2			The compliance statement for HP Routing switches that support ICMP Reply Limiting.
I32 hpicfIcmpReplyLimit	1.3.6.1.4.1.11.2.14.11.5.1.15.1.2.1.2	Integer32	read-write	The maximum number of icmp replies to send per second.
INT hpicfIcmpReplyLimitEnable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.2.1.1	INTEGER	read-write	Enable/Disable ICMP replies.
hpicfIcmpReplyLimitGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.4			A collection of objects allowing configuration of ICMP Reply rate limiting.
C32 hpicfInetCidrNumRouteDestinationsEx	1.3.6.1.4.1.11.2.14.11.5.1.15.1.5.3.1.1	Counter32	read-only	Total number of destinations for a particular inetCidrRouteDestType.
C32 hpicfInetCidrNumRouteRoutes	1.3.6.1.4.1.11.2.14.11.5.1.15.1.5.3.1.2	Counter32	read-only	Total number of routes for a particular inetCidrRouteDestType.
hpicfInetCidrRouteCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.11			A collection of objects for retrieving extended information about routes in the routing table.
hpicfInetCidrRouteCompliance1	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.14			A collection of objects for retrieving extended information (state and age) about routes in the routing table.
I32 hpicfInetCidrRouteDistance	1.3.6.1.4.1.11.2.14.11.5.1.15.1.5.2.1.1	Integer32	read-only	The administrative distance of this route.
hpicfInetCidrRouteEntry	1.3.6.1.4.1.11.2.14.11.5.1.15.1.5.2.1		not-accessible	Extended information about a single route.
hpicfInetCidrRouteGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.9			A collection of objects for retrieving extended information about routes in the routing table.
hpicfInetCidrRouteGroup1	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.19			A collection of objects for retrieving extended information (state and age) about routes in the routing table.
OID hpicfInetCidrRouteInfo	1.3.6.1.4.1.11.2.14.11.5.1.15.1.5.2.1.2	OBJECT IDENTIFIER	read-only	A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's inetCidrRouteProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntactically valid object identifier, and any implementation conforming to ASN.1 and the Basic Encoding Rules must be able to generate and recognize this value.
HPI hpicfInetCidrRouteState	1.3.6.1.4.1.11.2.14.11.5.1.15.1.5.2.1.3	HpInetCidrRouteState	read-only	The state of the route.
hpicfInetCidrRouteStatsCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.15			A collection of objects for retrieving the total number of destinations and routes for a particular inet type.
hpicfInetCidrRouteStatsEntry	1.3.6.1.4.1.11.2.14.11.5.1.15.1.5.3.1		not-accessible	Extended information about a scalar stats of the route.
hpicfInetCidrRouteStatsGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.20			The group of objects for the total number of destinations and routes for a particular inet type.
hpicfInetCidrRouteStatsTable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.5.3		not-accessible	HP extensions to the InetCidrRouteTable for scalar stats
hpicfInetCidrRouteTable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.5.2		not-accessible	HP extensions to the inetCidrRouteTable.
I32 hpicfIpCidrRouteDistance	1.3.6.1.4.1.11.2.14.11.5.1.15.1.5.1.1.1	Integer32	read-only	The administrative distance of this route.
hpicfIpCidrRouteEntry	1.3.6.1.4.1.11.2.14.11.5.1.15.1.5.1.1		not-accessible	Extended information about a single route.
hpicfIpCidrRouteGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.8			A collection of objects for retrieving extended information about routes in the routing table.
hpicfIpCidrRouteTable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.5.1		not-accessible	HP extensions to the ipCidrRouteTable.
hpicfIpDBroadcastFwdAclCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.20			The compliance statement for the ACL name being applied to IP Directed Broadcast.
IP hpicfIpDefaultRouterAddress	1.3.6.1.4.1.11.2.14.11.5.1.15.1.7.1.1.2	InetAddress	not-accessible	The address of the default router.
IPt hpicfIpDefaultRouterAddressType	1.3.6.1.4.1.11.2.14.11.5.1.15.1.7.1.1.1	InetAddressType	not-accessible	The address type of the default router. The only supported type is IPV6 as of now
hpicfIpDefaultRouterCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.8			The compliance statement for HP Routing switches that support Router Advertisements.
hpicfIpDefaultRouterEntry	1.3.6.1.4.1.11.2.14.11.5.1.15.1.8.1.1		not-accessible	Extended information about a single route.
hpicfIpDefaultRouterGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.14			The group of objects in a table for default routing.
I32 hpicfIpDefaultRouterHopLimit	1.3.6.1.4.1.11.2.14.11.5.1.15.1.8.1.1.2	Integer32	read-only	The hop limit to be used by the host on outgoing packets.
NUM hpicfIpDefaultRouterIfIndex	1.3.6.1.4.1.11.2.14.11.5.1.15.1.7.1.1.3	InterfaceIndex	not-accessible	The address of the default router.
I32 hpicfIpDefaultRouterMTU	1.3.6.1.4.1.11.2.14.11.5.1.15.1.8.1.1.1	Integer32	read-only	The link MTU size advertised by the router. The selected Mlink TU may be different from this one.
IP hpicfIpDefaultRouterPrefix	1.3.6.1.4.1.11.2.14.11.5.1.15.1.7.1.1.5	InetAddress	not-accessible	The prefix.
T/F hpicfIpDefaultRouterPrefixAutonomous	1.3.6.1.4.1.11.2.14.11.5.1.15.1.7.1.1.8	TruthValue	read-only	The object has the value true(1) if this prefix can be used for autonomous address configuration. If the value is false(2), the prefix is not used to autoconfigure a local interface address
hpicfIpDefaultRouterPrefixEntry	1.3.6.1.4.1.11.2.14.11.5.1.15.1.7.1.1		not-accessible	A row in the default router table, containing information about a single learnt default router
hpicfIpDefaultRouterPrefixInfo	1.3.6.1.4.1.11.2.14.11.5.1.15.1.7
ADR hpicfIpDefaultRouterPrefixLength	1.3.6.1.4.1.11.2.14.11.5.1.15.1.7.1.1.6	InetAddressPrefixLength	not-accessible	Length of the prefix.
T/F hpicfIpDefaultRouterPrefixOnLink	1.3.6.1.4.1.11.2.14.11.5.1.15.1.7.1.1.7	TruthValue	read-only	The object has the value true (1) if the prefix can be used for on-link determination, otherwise the value is false(2)
U32 hpicfIpDefaultRouterPrefixPrefdLifeTime	1.3.6.1.4.1.11.2.14.11.5.1.15.1.7.1.1.10	Unsigned32	read-only	The preferred life time for the router.
hpicfIpDefaultRouterPrefixTable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.7.1		not-accessible	Table of default routers learnt through auto-config This Table will be used in conjunction of ipDefaultRouterTable defined in RFC 4293 to get the attributes of the default routers learnt through auto-config
IPt hpicfIpDefaultRouterPrefixType	1.3.6.1.4.1.11.2.14.11.5.1.15.1.7.1.1.4	InetAddressType	not-accessible	Type of the prefix.
U32 hpicfIpDefaultRouterPrefixValidLifeTime	1.3.6.1.4.1.11.2.14.11.5.1.15.1.7.1.1.9	Unsigned32	read-only	The valid life time for the router.
hpicfIpDefaultRouterProperties	1.3.6.1.4.1.11.2.14.11.5.1.15.1.8
hpicfIpDefaultRouterTable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.8.1		not-accessible	HP extensions to the ipDefaultRouterTable.
I32 hpicfIpMaximumPaths	1.3.6.1.4.1.11.2.14.11.5.1.15.1.3.3	Integer32	read-write	Maximum number of equal cost paths to a destination that we will add to the IP routing table.
hpicfIpRouteBaseScalars	1.3.6.1.4.1.11.2.14.11.5.1.15.3
hpicfIpRouteBaseScalarsCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.10			This group contains both number of routing entries and number next hobs specified as part of routing table.
hpicfIpRouteBaseScalarsGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.16			This group contains both number of routing entries and number next hobs specified as part of routing table.
hpicfIpRouteCfgGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.5			A collection of objects allowing configuration of IP global enables.
U32 hpicfIpRouteCnt	1.3.6.1.4.1.11.2.14.11.5.1.15.1.10.1.1.2	Unsigned32	read-only	count of active routes per routing protocol.
hpicfIpRouteCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.21			The compliance statement for HP Routing switches.
U32 hpicfIpRouteCount	1.3.6.1.4.1.11.2.14.11.5.1.15.3.1	Unsigned32	read-only	This parameter specifies total number of routes in the Routing table.
hpicfIpRouteEntry	1.3.6.1.4.1.11.2.14.11.5.1.15.1.10.1.1		not-accessible	IP route summary table information.
U32 hpicfIpRouteNextHopCount	1.3.6.1.4.1.11.2.14.11.5.1.15.3.2	Unsigned32	read-only	This parameter specifies total number of next-hop entries in the Routing table. This parameter is useful to know how many other routers are connected and acting as a next-hop router for this router
HPI hpicfIpRouteProto	1.3.6.1.4.1.11.2.14.11.5.1.15.1.10.1.1.1	HpicfIpRouteProtoName	not-accessible	Protocol names that are enabled and active.
hpicfIpRouterCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.3			The compliance statement for HP Routing switches.
hpicfIpRouterOtherCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.12			The compliance statement for HP Routing switches.
hpicfIpRouteStats	1.3.6.1.4.1.11.2.14.11.5.1.15.1.5
hpicfIpRouteSummary	1.3.6.1.4.1.11.2.14.11.5.1.15.1.10
hpicfIpRouteSummaryCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.13			A collection of objects for active routes.
hpicfIpRouteSummaryTable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.10.1		not-accessible	IP route summary table in global context.
hpicfIpRouteSummaryTableGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.18			This group contains the count of active routes for each routing protocol.
hpicfIpRouting	1.3.6.1.4.1.11.2.14.11.5.1.15			This MIB module contains HP proprietary objects for managing IP Routing.
hpicfIpRoutingCompliances	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2
hpicfIpRoutingConformance	1.3.6.1.4.1.11.2.14.11.5.1.15.2
hpicfIpRoutingGroups	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1
hpicfIpRoutingObjects	1.3.6.1.4.1.11.2.14.11.5.1.15.1
hpicfIpStaticNeighborEntry	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.2.1		not-accessible	A row in the static neighbor table, containing information about a single configured static neighbor.
hpicfIpStaticNeighborGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.7			A collection of objects for configuring IP static neighbors.
NUM hpicfIpStaticNeighborIfIndex	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.2.1.1	InterfaceIndex	not-accessible	The ifIndex value for the interface used to reach this neighbor.
IP hpicfIpStaticNeighborNetAddress	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.2.1.3	InetAddress	not-accessible	The neighbor network address of this configured static neighbor. The type of address specified by this entry is indicated by the corresponding instance of the hpicfIpStaticNeighborNetAddrType object. An attempt to create a row in which the length of this object is not consistent with the type specified by hpicfIpStaticNeighborNetAddrType must be rejected.
IPt hpicfIpStaticNeighborNetAddrType	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.2.1.2	InetAddressType	not-accessible	The type of network address specified by this entry. Only the values 'ipv4(1)' and 'ipv6(2)' are expected. This object specifies the type of neighbor network address prefix in the hpicfIpStaticNeighborNetAddress object.
PHY hpicfIpStaticNeighborPhysAddress	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.2.1.4	PhysAddress	read-create	The media-dependent physical address used to reach this neighbor. The size of this address depends on the media type of the interface identified by hpicfIpStaticNeighborIfIndex.
ROW hpicfIpStaticNeighborStatus	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.2.1.5	RowStatus	read-create	Status of this neighbor entry. All writable columns in this table can be modified while the corresponding row is active.
hpicfIpStaticNeighborTable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.2		not-accessible	Table of configured IP static neighbors. This table uses a protocol-independent format, so that it can be used for both IPv4 and IPv6 static neighbors. Rows configured in this table should be stored in non-volatile storage.
IP hpicfIpStaticRouteBfdDstAddr	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.3.1.4	InetAddress	read-create	The IP address which is used as destination address for BFD
IPt hpicfIpStaticRouteBfdDstAddrType	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.3.1.3	InetAddressType	read-create	The type of IP address used as destination address for BFD
T/F hpicfIpStaticRouteBfdEnable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1.14	TruthValue	read-create	This object enables or disables BFD on Static route. When set to true(1), BFD is enabled for the session. When set to false(2), BFD is disabled for the session.
hpicfIpStaticRouteBfdEntry	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.3.1		not-accessible	Static route BFD table contains BFD objects. This table is added to provide BFD support to Static Routes. This is the additional param of Static Route table. The Value of Index in BFD table should be as same in Static Route table. 1. While enabling BFD static route, verify the RowStatus of hpicfIpStaticRouteTable for the configured index. 2. If Rowstatus is not present in hpicfIpStaticRouteTable Create Rowstatus for that recIndex in hpicfIpStaticRouteTable and then create the RowStatus in hpicfIpStaticRouteBfdTable. 3. While disabling the bfd Status, Destroy the rowstatus in hpicfIpStaticRouteBfdTable.
hpicfIpStaticRouteBfdGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.29			The group of objects in a table for configuring the bfd for static routes.
IP hpicfIpStaticRouteBfdSrcAddr	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.3.1.2	InetAddress	read-create	The IP address which is used as source address for BFD
IPt hpicfIpStaticRouteBfdSrcAddrType	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.3.1.1	InetAddressType	read-create	The type of IP address used as source address for BFD
ROW hpicfIpStaticRouteBfdStatus	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.3.1.5	RowStatus	read-create	Row status for this table.
hpicfIpStaticRouteBfdTable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.3		not-accessible	Extension of Static Route table to enable BFD on Static routes.
hpicfIpStaticRouteCompliance1	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.23			The compliance statement for HP Routing switches.
hpicfIpStaticRouteConfig	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4
I32 hpicfIpStaticRouteDistance	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1.8	Integer32	read-create	The administrative distance to associate with this static route. Routes with lower distances are preferred. By default, static routes are created with an administrative distance of 1, meaning they are preferred over all routes except directly connected routes. Setting a higher administrative distance for a route can be used for the following reasons: - by configuring multiple static routes to the same destination, one with the default distance and one with a higher distance, one can configure backup static routes - by configuring a static route with an administrative distance higher than the distance for a particular dynamic routing protocol, one can allow a static route to be overridden by dynamic routing information. Routes with an administrative distance of 255 will never be entered in the routing table.
hpicfIpStaticRouteEntry	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1		not-accessible	A row in the static route table, containing information about a single configured static route. There are 3 legal cases for the indexing this table: 1. ((hpicfIpStaticRouteFwdAddrType == hpicfIpStaticRoutePrefixType) && (hpicfIpStaticRouteFwdAddr is IP address of appropriate type) && (hpicfIpStaticRouteFwdIfIndex == 0)) Normal, remote static route. hpicfIpStaticRouteType will be equal to 'remote'. Note that the first condition that the FwdAddrType must equal the PrefixType exactly is not strictly true. For example, in IPv6, it is quite legal and expected to configure a static route where the PrefixType is ipv6, and the Prefix is a 16 byte IPv6 destination address, but the FwdAddrType is ipv6z and the FwdAddr is a 20 byte scoped IPv6 link-local address. 2. ((hpicfIpStaticRouteFwdAddrType == 'unknown') && (hpicfIpStaticRouteFwdAddr == zero-length string) && (hpicfIpStaticRouteFwdIfIndex != 0)) Interface route. Treated like a connected route. hpicfIpStaticRouteType will be equal to 'local'. 3. ((hpicfIpStaticRouteFwdAddrType == 'unknown') && (hpicfIpStaticRouteFwdAddr == zero-length string) && (hpicfIpStaticRouteFwdIfIndex == 0)) Discard route. hpicfStaticRouteType will be equal to either 'reject' or 'discard'.
IP hpicfIpStaticRouteFwdAddr	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1.5	InetAddress	not-accessible	For remote routes, the value of the next specified router to use for forwarding packets to the destination specified by this route. Note that this router does not need to be directly connected. In the case where it is not, the actual routing table entry will use a next hop determined by looking up the best route to this forwarding address. For non-remote routes, the value of this object will be a zero-length string. An attempt to create a row in which the length of this object is not consistent with the type specified by hpicfIpStaticRouteFwdAddrType must be rejected. An attempt to create a row with a value for this object other than a zero-length string must be rejected if the corresponding instance of the hpicfIpStaticRouteFwdIfIndex object is non-zero.
IPt hpicfIpStaticRouteFwdAddrType	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1.4	InetAddressType	not-accessible	The type of forwarding address for this route. The value of this object must be equal either to 'unknown' or to a value appropriate for the corresponding instance of the hpicfIpStaticRoutePrefixType object. For non-remote routes, the value of this object must be 'unknown'.
NUM hpicfIpStaticRouteFwdIfIndex	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1.6	InterfaceIndexOrZero	not-accessible	For remote routes, the value of this object must be zero. For reject or blackhole routes, the value of this object must be zero. For local routes, this object indicates the ifIndex of the local interface to use to reach this destination.
hpicfIpStaticRouteGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.6			A collection of objects for configuring IP static routes.
INT hpicfIpStaticRouteLogging	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1.13	INTEGER	read-create	This object determines whether or not debug log messages are to be generated for packets matching statically configured blackhole routes. When enabled, the debug option 'ip/ipv6 fib blackhole' needs to be enabled in order to print the log messages to a specified destination.
MET hpicfIpStaticRouteMetric	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1.11	Metric	read-create	Metric value for this route. It is used to compare static route with other static routes to the same destination. The acceptable range is from 1 to 255, both inclusive.
STR hpicfIpStaticRouteName	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1.12	DisplayString	read-create	Name of the configured static route. It is used for lucidity and troubleshooting purpose and is optional.
hpicfIpStaticRouteNameCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.18			The compliance statement for the static route name to add visibility to the static route being configured
hpicfIpStaticRouteNameGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.23			This group member is used to configure name of the static route being configured
hpicfIpStaticRouteOtherGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.17			The group of objects for configuring IP static routes.
hpicfIpStaticRouteParamGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.26			A collection of objects for configuring IP static routes.
hpicfIpStaticRouteParamGroup1	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.28			A collection of objects for configuring IP static routes.
IP hpicfIpStaticRoutePrefix	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1.2	InetAddress	not-accessible	The destination address prefix of this route. The type of address specified by this route is indicated by the corresponding instance of the hpicfIpStaticRoutePrefixType object. An attempt to create a row in which the length of this object is not consistent with the type specified by hpicfIpStaticRoutePrefixType must be rejected. An attempt to create a row in which the value X of this object, logically ANDed with the value of the mask formed from the corresponding instance of the hpicfIpStaticRoutePrefixLength object, is not equal to X must be rejected, i.e., this prefix may not have any 'host' bits set.
ADR hpicfIpStaticRoutePrefixLength	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1.3	InetAddressPrefixLength	not-accessible	This object indicates the number of leading one bits which form the mask to be logically ANDed with a destination address before comparison with the corresponding instance of the hpicfIpStaticRoutePrefix object for a route match operation. An attempt to create a row in which the value of this object is longer than the maximum legal length of an address of the type indicated by the corresponding instance of the hpicfIpStaticRoutePrefixType object must be rejected. An attempt to create a row in which the value of the mask formed from this object logically ANDed with the value of the corresponding instance of the hpicfIpStaticRoutePrefix object is not equal to the hpicfIpStaticRoutePrefix.
IPt hpicfIpStaticRoutePrefixType	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1.1	InetAddressType	not-accessible	The type of destination prefix specified by this route. The value 'dns(16)' is not supported. This object specifies the type of destination address prefix in the hpicfIpStaticRoutePrefix object.
ROW hpicfIpStaticRouteStatus	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1.10	RowStatus	read-create	Status of this route entry. All writable columns in this table can be modified while the corresponding row is active.
hpicfIpStaticRouteTable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1		not-accessible	Table of configured IP static routes. This table uses a protocol-independent format, so that it can be used for both IPv4 and IPv6 static routes. Rows configured in this table should be stored in non-volatile storage.
U32 hpicfIpStaticRouteTag	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1.9	Unsigned32	read-create	Tag value that can be used to filter redistribution of this route via route maps.
INT hpicfIpStaticRouteType	1.3.6.1.4.1.11.2.14.11.5.1.15.1.4.1.1.7	INTEGER	read-create	The type of route. The value 'other' is not supported, and is included only for compatibility with the IP Forwarding Table MIB. The value 'local' indicates that the destination is treated as if it were directly connected. The value 'remote' indicates that the forwarding address will be used to reach the destination. The value 'reject' indicates that if this route is matched, a packet to the destination is discarded and a notification (e.g. ICMP error) is returned to the packet sender. The value 'blackhole' indicates that if the route is matched, a packet to the destination is silently dropped. The value of this object must be consistent with the forwarding address information used to index the route.
hpicfIpv6ND	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9
hpicfIpv6NDRAAdminCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.9			IPV6 neighbor discovery router advertisement global admin status.
hpicfIpv6NDRAAdminGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.15			This group member is used to enable / disable IPV6 neighbor discovery router advertisement global admin status.
T/F hpicfIpv6NDRAAdminStatus	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.1	TruthValue	read-write	A flag indicating whether or not the router sends periodic router advertisements and responds to router solicitations.
hpicfIpv6NDRADNSAdminCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.17			IPV6 router advertisement DNS option global admin status.
hpicfIpv6NDRADNSAdminGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.22			This group member is used to enable / disable IPV6 router advertisement DNS option global admin status.
T/F hpicfIpv6NDRADNSAdminStatus	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.4	TruthValue	read-write	A flag indicating whether or not the router includes DNS options with periodic router advertisements.
U32 hpicfIpv6RouteCnt	1.3.6.1.4.1.11.2.14.11.5.1.15.1.11.1.1.2	Unsigned32	read-only	A count of active IPv6 routes per routing protocol.
hpicfIpv6RouteEntry	1.3.6.1.4.1.11.2.14.11.5.1.15.1.11.1.1		not-accessible	IPv6 route summary table information.
HPI hpicfIpv6RouteProto	1.3.6.1.4.1.11.2.14.11.5.1.15.1.11.1.1.1	HpicfIpv6RouteProtoName	not-accessible	IPv6 route protocol names that are enabled and active.
INT hpicfIpv6RouterAdvertRtrPreference	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.3.1.3	INTEGER	read-write	Indicates whether to prefer this router over other default routers.
T/F hpicfIpv6RouterAdvertSendDNSAdverts	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.3.1.2	TruthValue	read-write	A flag indicating whether or not the router includes DNS options in periodic router advertisements on this interface.
hpicfIpv6RouteSummary	1.3.6.1.4.1.11.2.14.11.5.1.15.1.11
hpicfIpv6RouteSummaryCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.19			A collection of objects providing information about an active IPv6 routes.
hpicfIpv6RouteSummaryTable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.11.1		not-accessible	IPv6 route summary table in the global context.
hpicfIpv6RouteSummaryTableGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.24			This group contains the count of active IPv6 routes for each routing protocol.
hpicfIpv6RtrAdvCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.6			The compliance statement for HP Routing switches that support Router Advertisements
INT hpicfIpv6RtrAdvCurHopLimitMode	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.3.1.1	INTEGER	read-write	This object indicates whether the value in ipv6RouterAdvertCurHopLimit is in use or the value in ipv6IpDefaultHopLimit is in use for an entry in this table. A set to 'global' means: - ipv6IpDefaultHopLimit value will be used for hop limit. A set to 'perInterface' means: - ipv6RouterAdvertCurHopLimit value will be used for hop limit.
hpicfIpv6RtrAdvDNSCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.16			The compliance statement for HP Routing switches that support Router Advertisements
hpicfIpv6RtrAdvDNSGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.21			The group of objects in a table for configuring the Router Advertisement options.
hpicfIpv6RtrAdvEntry	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.3.1		not-accessible	An entry in the hpicfIpv6RtrAdvEntry contains Router Advertisement parameters.
hpicfIpv6RtrAdvGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.12			The group of objects in a table for configuring the Router Advertisement options.
hpicfIpv6RtrAdvParamCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.22			The compliance statement for HP Routing switches that support Router Advertisements
hpicfIpv6RtrAdvParamGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.27			The group of objects in a table for configuring the Router Advertisement options.
T/F hpicfIpv6RtrAdvPrefixAdvertiseFlag	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.2.1.11	TruthValue	read-create	Specifies whether the prefix in this entry is advertised or not.When set to TRUE prefix is advertised.
T/F hpicfIpv6RtrAdvPrefixAutonomousFlag	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.2.1.6	TruthValue	read-create	Autonomous address configuration flag. Router Advertisement messages are sent out with the autonomous flag field set to this value in the Prefix Information.
hpicfIpv6RtrAdvPrefixCompliance	1.3.6.1.4.1.11.2.14.11.5.1.15.2.2.5			The compliance statement for HP Routing switches that support Router Advertisements
hpicfIpv6RtrAdvPrefixEntry	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.2.1		not-accessible	An entry in the hpicfIpv6RtrAdvPrefixTable.
hpicfIpv6RtrAdvPrefixGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.11			The group of objects in a table for configuring the Router Advertisement options.
NUM hpicfIpv6RtrAdvPrefixIfIndex	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.2.1.1	InterfaceIndex	not-accessible	The index value which uniquely identifies the interface on which this prefix is configured. The interface identified by a particular value of this index is the same interface as identified by the same value of the IF-MIB's ifIndex.
ADR hpicfIpv6RtrAdvPrefixLength	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.2.1.4	InetAddressPrefixLength	not-accessible	The prefix length associated with this prefix. The value 0 has no special meaning for this object. It simply refers to address '::/0'.
INT hpicfIpv6RtrAdvPrefixLifetimeType	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.2.1.7	INTEGER	read-create	Specifies if the hpicfIpv6RtrAdvPrefixPreferredLifetime and hpicfIpv6RtrAdvPrefixValidLifetime are of the kind where consecutive advertisements have the same time(fixed) or a time that decrements in real time. The realTime(2) can be used to specify a time in future at which the LifeTimes become zero.
T/F hpicfIpv6RtrAdvPrefixOnLinkFlag	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.2.1.5	TruthValue	read-create	Router Advertisement messages are sent out with the On-Link flag (L-bit) field set to this value.
U32 hpicfIpv6RtrAdvPrefixPreferredLifetime	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.2.1.8	Unsigned32	read-create	The length of time ,in seconds,that this prefix will be preferred. A value of 4,294,967,295 represents infinity. The Router Advertisement messages are sent out with the Preferred LifeTime field set to this value. To specify in a realTime way,set this object to a future time in number of seconds since January 1, 1990, Coordinated Universal Time and also set hpicfIpv6RtrAdvPrefixTimeType to realTime. The default value is 7 days(604800 seconds) fixed time
IP hpicfIpv6RtrAdvPrefixPrefix	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.2.1.3	InetAddress	not-accessible	The address prefix. The address type of this object is specified in hpicfIpv6RtrAdvPrefixType. The length of this object is the standard length for objects of that type.
ROW hpicfIpv6RtrAdvPrefixRowStatus	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.2.1.10	RowStatus	read-create	The status of this conceptual row. As all objects in this conceptual row have default values a row can be created and made active by setting this object appropriately.
hpicfIpv6RtrAdvPrefixTable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.2		not-accessible	This table describes the router advertisement configuration variables for each interface.
IPt hpicfIpv6RtrAdvPrefixType	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.2.1.2	InetAddressType	not-accessible	The address type of hpicfIpv6RtrAdvPrefixPrefix.
U32 hpicfIpv6RtrAdvPrefixValidLifetime	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.2.1.9	Unsigned32	read-create	The length of time, in seconds, that this prefix will continue to be valid, i.e. time until invalidation. A value of 4,294,967,295 represents infinity. The Router advertisement messages are sent out with the Valid LifeTime field set to this value. To specify in a realTime way,set this object to a future time in number of seconds since January 1, 1990, Coordinated Universal Time and also set hpicfIpv6RtrAdvPrefixTimeType to realTime. The default value is 30 days (or 2592000 seconds) fixed time.
hpicfIpv6RtrAdvTable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.9.3		not-accessible	This table augments ipv6RouterAdvertEntry and it contains HP proprietary objects for managing router advertisements.
INT hpicfRdiscAdminStatus	1.3.6.1.4.1.11.2.14.11.5.1.15.1.1.1	INTEGER	read-write	The administrative status of the ICMP Router Discovery protocol.
hpicfRdiscBaseGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.1			Basic ICMP Router Discovery configuration objects.
INT hpicfRdiscIfAdminStatus	1.3.6.1.4.1.11.2.14.11.5.1.15.1.1.2.1.1	INTEGER	read-write	The administrative status of the ICMP Router Discovery protocol on this interface.
INT hpicfRdiscIfAdvertAddress	1.3.6.1.4.1.11.2.14.11.5.1.15.1.1.2.1.2	INTEGER	read-write	The destination address to be used for router advertisements on this interface. If the value of this object is 'multicast' (the default), router advertisements sent on this interface will be sent to the all-hosts multicast address, 224.0.0.1. If the value of this object is 'broadcast', router advertisements sent on this interface will be sent to the limited broadcast address, 255.255.255.255.
I32 hpicfRdiscIfAdvertLifetime	1.3.6.1.4.1.11.2.14.11.5.1.15.1.1.2.1.5	Integer32	read-write	The value to be placed in the Lifetime field of Router Advertisements sent on this interface. Must be no less than hpicfRdiscMaxAdvertInterval.
hpicfRdiscIfCfgEntry	1.3.6.1.4.1.11.2.14.11.5.1.15.1.1.2.1		not-accessible	Router discovery configuration information for a single interface.
hpicfRdiscIfCfgGroup	1.3.6.1.4.1.11.2.14.11.5.1.15.2.1.2			A collection of objects allowing per-interface configuration of ICMP Router Discovery operation.
hpicfRdiscIfCfgTable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.1.2		not-accessible	Per-interface configuration for the ICMP Router Discovery protocol.
I32 hpicfRdiscIfMaxAdvertInterval	1.3.6.1.4.1.11.2.14.11.5.1.15.1.1.2.1.3	Integer32	read-write	The maximum time allowed between sending unsolicited Router Advertisements on this interface.
I32 hpicfRdiscIfMinAdvertInterval	1.3.6.1.4.1.11.2.14.11.5.1.15.1.1.2.1.4	Integer32	read-write	The minimum time allowed between sending unsolicited Router Advertisements on this interface. Must be no greater than hpicfRdiscMaxAdvertInterval.
I32 hpicfRdiscIfPreference	1.3.6.1.4.1.11.2.14.11.5.1.15.1.1.2.1.6	Integer32	read-write	The preference of the router as a default router, relative to the other routers on the same subnet. Higher values are more preferable. The minimum value (0x80000000) is used to indicate that the router, even though it may be advertised, is not to be used by neighboring hosts as a default router.
INT hpicfSourceRouteEnable	1.3.6.1.4.1.11.2.14.11.5.1.15.1.3.2	INTEGER	read-write	Enable/disable source routed forwarding.

RFC description

Vendor-private MIB for HP ICF (Intelligent Computing Fabric) IP routing management and configuration.

Start monitoring HP ProCurve Layer 3 switch (static IP routing config) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HP-ICF-IP-ROUTING