All MIBs › HP-ICF-IPCONFIG
Organization: HP Networking
Last Updated: 2017-06-07
Category: IP and Core Protocols, Technology: Routing/L3, Vendor: HP/HPE
Description: HP ICF SNMP MIB for IP interface configuration management including address assignment and interface settings on HP ProCurve switches.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HP-ICF-IPCONFIG?
HP-ICF-IPCONFIG is an HP proprietary MIB providing basic IP address and interface configuration management for devices in HP's Integrated Communication Facility (ICF) product line, i.e. HP ProCurve switches. It exposes objects for assigning and viewing IP addresses on management/routed interfaces and general interface configuration settings. Its monitoring value is primarily configuration-status verification: administrators confirm the device's management IP address and interface settings are correctly applied, which is foundational to ensuring the device remains reachable for further SNMP or CLI-based management. It builds on the standard IF-MIB interface indexing model as its underlying dependency for associating IP configuration with specific interfaces. It is deployed on HP ProCurve switches wherever basic in-band or out-of-band IP management configuration needs to be verified or changed. Network engineers evaluating or troubleshooting this functionality can download the HP-ICF-IPCONFIG file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HP-ICF-IPCONFIG. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- HP ProCurve network switch
Monitoring Examples
No specific object or table names were available in the provided sample for this MIB, so a concrete polling scenario with real identifiers cannot be constructed here. Based on its stated purpose, an admin would typically expect to check the device's configured management IP address and subnet/interface association to confirm reachability, noticing a mismatch if the switch becomes unreachable after a configuration change. Without sample objects, no invented names are used given the absence of sample data.
This MIB depends on
Related MIBs
Imported Objects
From HP-ICF-OID
| hpicfCommon | OBJECT-IDENTITY |
From IF-MIB
| ifIndex | OBJECT-TYPE |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressIPv4 | |
| InetAddressPrefixLength | |
| InetAddressType | |
| InetPortNumber |
From IP-MIB
| IpAddressOriginTC | |
| IpAddressStatusTC | |
| ipNetToPhysicalEntry | OBJECT-TYPE |
| ipv4InterfaceEntry | OBJECT-TYPE |
| ipv6InterfaceEntry | OBJECT-TYPE |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TruthValue |
From TUNNEL-MIB
| tunnelInetConfigEntry | OBJECT-TYPE |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hpicfIpConfig | 1.3.6.1.4.1.11.2.14.11.1.10 | This MIB module describes objects for basic IP address configuration and interface configuration for devices in the HP Integrated Communication Facility product line. | ||
| hpicfIpConfigObjects | 1.3.6.1.4.1.11.2.14.11.1.10.1 | |||
| hpicfIpAddressObjects | 1.3.6.1.4.1.11.2.14.11.1.10.1.1 | |||
| hpicfIpAddressTable | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1 | not-accessible | This table contains manually configured IPv4 and IPv6 addresses for each interface. An entry in this table may not exist in the active state unless all objects in the entry are consistent. In particular, the value of hpicfIpAddressPrefixLength. | |
| hpicfIpAddressEntry | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1 | not-accessible | An entry in the hpicfIpAddressEntry contains a single manually configured IP address. | |
| IPt hpicfIpAddressAddrType | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.1 | InetAddressType | not-accessible | Type of IP address |
| IP hpicfIpAddressAddr | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.2 | InetAddress | not-accessible | The IP address to which this entry's addressing information pertains. hpicfIpAddressAddr is always interpreted within the context of hpicfIpAddressAddrType. |
| ADR hpicfIpAddressPrefixLength | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.3 | InetAddressPrefixLength | read-create | The prefix length associated with IP address. |
| INT hpicfIpAddressType | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.4 | INTEGER | read-create | IP address type. For V4 addresses the value will be unicast. |
| ROW hpicfIpAddressRowStatus | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.5 | RowStatus | read-create | The status of the IP address entry. |
| INT hpicfIpAddressExtendedType | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.1.1.6 | INTEGER | read-create | IP address type. For V4 addresses the value will be none. For V6 address it can be eui64 and linkLocal also. |
| hpicfSwitchIpAddressTable | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2 | not-accessible | This read only table contains IPV4 and/or IPV6 addresses for each interface. These IP Addresses are either manually configured or obtained by a dynamic method (such as DHCP). This table will hold all manually configured IP Addresses that exist in hpicfIpAddressTable except for those entries that are not in active state (hpicfIpAddressRowStatus). | |
| hpicfSwitchIpAddressEntry | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1 | not-accessible | An entry in the hpicfSwitchIpAddressEntry contains a single IP address. | |
| IPt hpicfSwitchIpAddressAddrType | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.1 | InetAddressType | not-accessible | Type of IP address. |
| IP hpicfSwitchIpAddressAddr | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.2 | InetAddress | not-accessible | The IP address to which this entry's addressing information pertains. hpicfSwitchIpAddressAddr is always interpreted within the context of hpicfSwitchIpAddressAddrType. |
| ADR hpicfSwitchIpAddressPrefixLength | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.3 | InetAddressPrefixLength | read-only | The prefix length associated with IP address. |
| INT hpicfSwitchIpAddressType | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.4 | INTEGER | read-only | IP address type. For V4 addresses the value will be unicast. |
| NUM hpicfSwitchIpAddressOrigin | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.5 | IpAddressOriginTC | read-only | The origin of the address. |
| ADR hpicfSwitchIpAddressStatus | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.6 | IpAddressStatusTC | read-only | The status of the address, describing if the address can be used for communication. In the absence of other information, an IPv4 address is always preferred(1). |
| U32 hpicfSwitchIpAddressPreferredLifetime | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.7 | Unsigned32 | read-only | The remaining length of time in seconds that this address will continue to be preferred, i.e. time until deprecation. A value of 4,294,967,295 represents infinity. The address generated from a deprecated address should no longer be used as a source address in new communications, but packets received on such an interface are processed as expected. The default for IPv4 addresses is 4,294,967,295 (infinity). |
| U32 hpicfSwitchIpAddressValidLifetime | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.8 | Unsigned32 | read-only | The remaining length of time, in seconds, that this address will continue to be valid, i.e. time until invalidation. A value of 4,294,967,295 represents infinity. The address generated from an invalidated address should not appear as the destination or source address of a packet. The default for IPv4 addresses is 4,294,967,295 (infinity). |
| INT hpicfSwitchIpAddressExtendedType | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.2.1.9 | INTEGER | read-only | IP address type. For V4 addresses the value will be none. For V6 address it can be eui64 and linkLocal also. |
| hpicfIpNetToPhysicalTable | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.3 | not-accessible | This table augments ipNeTtoPhysicalTable | |
| hpicfIpNetToPhysicalEntry | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.3.1 | not-accessible | This table augments ipNeTtoPhysicalTable | |
| I32 hpicfIpNetToPhysicalPort | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.3.1.1 | Integer32 | read-create | This object gives the port through which the physical address was learnt |
| INT hpicfIpNetToPhysicalTableClear | 1.3.6.1.4.1.11.2.14.11.1.10.1.1.4 | INTEGER | read-write | This provides the clear options for hpicfIpNetToPhysicalTable. A value of 2 is to clear arp table. A value of 3 is to clear the ipv6 neighbor table. A get returns 'unknown' always. |
| hpicfIpv4InterfaceObjects | 1.3.6.1.4.1.11.2.14.11.1.10.1.2 | |||
| hpicfIpv4InterfaceTable | 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1 | not-accessible | This table contains per-interface IPV4 configuration information. | |
| hpicfIpv4InterfaceEntry | 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1 | not-accessible | An entry in the hpicfIpv4InterfaceEntry contains IPV4 interface specific configuration information. This table is indexed by ipv4InterfaceIfIndex. | |
| INT hpicfIpv4InterfaceDhcpEnable | 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.1 | INTEGER | read-write | Changing this flag to 'full' will clear any existing IP address configuration for this interface and will cause the device to use a dynamic method (e.g. DHCP) to obtain its IP configuration and other configuration parameter (such as gateway, time of day, etc...) for this interface. Setting this flag to 'inform' will allow manual IP address configuration and yet permit other configuration parameters (such as gateway, time of day, etc...) to be obtained from a DHCP server. Setting this flag to 'off' will allow manual IP configuration but disallow any DHCP configuration. |
| INT hpicfIpv4InterfaceForwarding | 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.2 | INTEGER | read-write | This flag indicates whether this interface is forwarding the datagrams that were not addressed to this interface. Setting this flag to 'enabled' (the default) results in forwarding the datagrams that were not addressed to this interface. Setting this flag to 'disabled' results in ignoring datagrams that were not addressed to this entity. |
| INT hpicfIpv4InterfaceProxyArp | 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.3 | INTEGER | read-write | Enables/disables ARP proxy on the interface. If set to 'enabled', the switch will respond on ARP request for IP addresses from other subnets. If set to disabled (the default), the switch will not respond on ARP request for IP addresses from other subnets. |
| INT hpicfIpv4InterfaceLocalProxyArp | 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.4 | INTEGER | read-write | Enables/disables local ARP proxy on the interface. If set to 'enabled', the switch will respond on ARP request for IP addresses within the local subnet. If set to disabled (the default), the switch will not respond on ARP request for IP addresses within the local subnet. |
| ADR hpicfIpv4InterfaceBootpGateway | 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.5 | InetAddressIPv4 | read-write | This entry will specify the IP address to be used as the BOOTP gateway for this interface. Note that this IP address will be used as the BOOTP gateway only when it is configured as an IP address on this interface. Otherwise, the lowest IP address configured on the interface will be used as the gateway address. |
| INT hpicfIpv4InterfaceDirectedBcastFwd | 1.3.6.1.4.1.11.2.14.11.1.10.1.2.1.1.6 | INTEGER | read-write | Enable/disable directed-broadcast forwarding on this interface. When set to default, the global hpicfDBroadcastFwdEnable setting is used. When set to enable, directed-broadcasts are enabled irrespective of the global setting. |
| hpicfUdpTunnelTable | 1.3.6.1.4.1.11.2.14.11.1.10.1.2.3 | not-accessible | This table contains per interface IPV4 Udp encapsulated tunnel specific configuration information. | |
| hpicfUdpTunnelEntry | 1.3.6.1.4.1.11.2.14.11.1.10.1.2.3.1 | not-accessible | An entry in the hpicfUdpTunnelEntry contains Udp encapsulated tunnel specific configuration information. | |
| INE hpicfUdpTunnelSrcPort | 1.3.6.1.4.1.11.2.14.11.1.10.1.2.3.1.1 | InetPortNumber | read-create | This variable is valid only for the remote mirroring source or destination switch. The value will be ignored otherwise. A value of 0 means that the UDP port is irrelevant for the tunnel type. If this value is non-zero it must be duplicated in the tunnelInetConfigID value (this will ensure that a given UDP port can only be associated once with a given tunnelInetConfigAddressType, tunnelInetConfigLocalAddress, tunnelInetConfigRemoteAddress, tunnelInetConfigEncapsMethod combination). |
| I32 hpicfUdpTunnelMirrorSessionID | 1.3.6.1.4.1.11.2.14.11.1.10.1.2.3.1.2 | Integer32 | read-create | This variable is valid only for a remote mirroring switch which interfaces with the source end of the tunnel. The value will be ignored otherwise. A value of 0 means that the mirror session ID is irrelevant for the tunnel type. |
| INT hpicfUdpTunnelMirrorTruncate | 1.3.6.1.4.1.11.2.14.11.1.10.1.2.3.1.3 | INTEGER | read-write | Enables/disables truncation for remote mirroring. |
| hpicfIpClientTrackerObjects | 1.3.6.1.4.1.11.2.14.11.1.10.1.3 | |||
| T/F hpicfIpClientTrackerEnable | 1.3.6.1.4.1.11.2.14.11.1.10.1.3.1 | TruthValue | read-write | Enable ip client tracking for trusted and untrusted devices. |
| T/F hpicfIpClientTrackerTrusted | 1.3.6.1.4.1.11.2.14.11.1.10.1.3.2 | TruthValue | read-write | Enable ip client tracking for trusted devices. |
| T/F hpicfIpClientTrackerUntrusted | 1.3.6.1.4.1.11.2.14.11.1.10.1.3.3 | TruthValue | read-write | Enable ip client tracking for untrusted devices. |
| hpicfIpConfigConformance | 1.3.6.1.4.1.11.2.14.11.1.10.2 | |||
| hpicfIpConfigCompliances | 1.3.6.1.4.1.11.2.14.11.1.10.2.1 | |||
| hpicfIpConfigCompliance | 1.3.6.1.4.1.11.2.14.11.1.10.2.1.1 | A compliance statement for HP Routing switches with IP Configuration | ||
| hpicfIpConfigCompliance2 | 1.3.6.1.4.1.11.2.14.11.1.10.2.1.2 | A compliance statement for HP Routing switches with IP Configuration | ||
| hpicfIpConfigCompliance4 | 1.3.6.1.4.1.11.2.14.11.1.10.2.1.4 | A compliance statement for HP Routing switches with IP Configuration | ||
| hpicfIpConfigCompliance5 | 1.3.6.1.4.1.11.2.14.11.1.10.2.1.5 | A compliance statement for HP Routing switches with IP Configuration | ||
| hpicfIpConfigCompliance6 | 1.3.6.1.4.1.11.2.14.11.1.10.2.1.6 | A compliance statement for HP Routing switches with IP Configuration | ||
| hpicfIpConfigCompliance7 | 1.3.6.1.4.1.11.2.14.11.1.10.2.1.7 | A compliance statement for HP Routing switches with IP Configuration | ||
| hpicfIpConfigCompliance8 | 1.3.6.1.4.1.11.2.14.11.1.10.2.1.8 | A compliance statement for HP Routing switches with IP Configuration | ||
| hpicfIpConfigCompliance9 | 1.3.6.1.4.1.11.2.14.11.1.10.2.1.9 | A compliance statement for HP Routing switches with IP Configuration | ||
| hpicfIpConfigCompliance10 | 1.3.6.1.4.1.11.2.14.11.1.10.2.1.10 | A compliance statement for IP Client tracking | ||
| hpicfIpConfigCompliance11 | 1.3.6.1.4.1.11.2.14.11.1.10.2.1.11 | A compliance statement for IP Client tracking | ||
| hpicfIpConfigGroups | 1.3.6.1.4.1.11.2.14.11.1.10.2.2 | |||
| hpicfIpAddressTableGroup | 1.3.6.1.4.1.11.2.14.11.1.10.2.2.1 | A Collection of objects allowing configuration of an IP address for an interface. | ||
| hpicfSwitchIpAddressTableGroup | 1.3.6.1.4.1.11.2.14.11.1.10.2.2.2 | A Collection of objects providing interfaces addressing information. | ||
| hpicfIpv4InterfaceTableGroup | 1.3.6.1.4.1.11.2.14.11.1.10.2.2.3 | Deprecated - see hpicfIpv4InterfaceTableGroup2 | ||
| hpicfUdpTunnelTableGroup | 1.3.6.1.4.1.11.2.14.11.1.10.2.2.4 | A Collection of objects that allows IPV4 interface configuration for remote mirroring | ||
| hpicfIpv6InterfaceTableGroup | 1.3.6.1.4.1.11.2.14.11.1.10.2.2.5 | A Collection of objects that allows IPV6 interface configuration | ||
| hpicfIpv4InterfaceTableGroup2 | 1.3.6.1.4.1.11.2.14.11.1.10.2.2.6 | A Collection of objects that allows IPV4 interface configuration | ||
| hpicfIpv6DadAttemptsGroup | 1.3.6.1.4.1.11.2.14.11.1.10.2.2.7 | A collection of objects that allows the number of DAD Attempts to be configured globally and also on a per interface basis. | ||
| hpicfIpv6IcmpGroup | 1.3.6.1.4.1.11.2.14.11.1.10.2.2.8 | Objects provided for the ipv6 icmp configuration. | ||
| hpicfIpNetToPhysicalTableGroup | 1.3.6.1.4.1.11.2.14.11.1.10.2.2.9 | Objects provided for the clear options in the device. | ||
| hpicfUdpTunnelMirrorGroup | 1.3.6.1.4.1.11.2.14.11.1.10.2.2.10 | An object that enables or disables truncation for remote mirroring. | ||
| hpicfIpv6NDGroup | 1.3.6.1.4.1.11.2.14.11.1.10.2.2.11 | Objects provided for configuration of ipv6 ND parameters | ||
| hpicfIpv4InterfaceTableGroup3 | 1.3.6.1.4.1.11.2.14.11.1.10.2.2.12 | A Collection of objects that allows IPV4 interface configuration | ||
| hpicfIpClientTrackerGroup | 1.3.6.1.4.1.11.2.14.11.1.10.2.2.13 | Deprecated - see hpicfIpClientTrackerGroup2 | ||
| hpicfIpClientTrackerGroup2 | 1.3.6.1.4.1.11.2.14.11.1.10.2.2.14 | A Collection of objects that allows IpClient Tracking | ||
| hpicfIpv6ConfigObjects | 1.3.6.1.4.1.11.2.14.11.1.10.3 | |||
| hpicfIpv6GlobalConfigObjects | 1.3.6.1.4.1.11.2.14.11.1.10.3.1 | |||
| hpicfIpv6NDObjects | 1.3.6.1.4.1.11.2.14.11.1.10.3.1.1 | |||
| I32 hpicfIpv6NDDadAttempts | 1.3.6.1.4.1.11.2.14.11.1.10.3.1.1.1 | Integer32 | read-write | The value in this object indicates the maximum number of neighbor solicitation requests that will be sent while performing duplicate address detection. |
| hpicfIpv6IcmpObjects | 1.3.6.1.4.1.11.2.14.11.1.10.3.1.2 | |||
| I32 hpicfIpv6IcmpErrorInterval | 1.3.6.1.4.1.11.2.14.11.1.10.3.1.2.1 | Integer32 | read-write | The value in this object indicates the error interval in which the token bucket algorithm places one token in the bucket for ICMPV6 rate limiting.Each token represents the right to send one ICMP error message. Each time an error is sent, it takes a token from the bucket. ICMP will not be allowed to originate an error message if the bucket is empty. |
| I32 hpicfIpv6IcmpBucketsize | 1.3.6.1.4.1.11.2.14.11.1.10.3.1.2.2 | Integer32 | read-write | The value in this object indicates the maximum number of tokens that can be in the bucket. |
| hpicfIpv6InterfaceObjects | 1.3.6.1.4.1.11.2.14.11.1.10.3.2 | |||
| hpicfIpv6InterfaceTable | 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1 | not-accessible | This table contains per-interface IPV6 configuration information. | |
| hpicfIpv6InterfaceEntry | 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1 | not-accessible | An entry in the hpicfIpv6InterfaceEntry contains IPV6 interface specific configuration information. This table is indexed by ipv6InterfaceIfIndex. | |
| INT hpicfIpv6InterfaceDhcpMode | 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.1 | INTEGER | read-write | Setting this flag to 'dhcpFull' will clear any existing IP address configuration for this interface and will cause the device to use a dynamic method (e.g. DHCP) to obtain its IP configuration and other configuration parameter (such as gateway, time of day, etc...) for this interface. Setting this flag to 'dhcpInform' will allow manual IP address configuration and yet permit other configuration parameters (such as gateway, time of day, etc...) to be obtained from a DHCP server. Setting this flag to 'disabled' will not allow any of the above mentioned two configuration, but interface can have link-local, auto-config and manual ip-address. |
| INT hpicfIpv6InterfaceManual | 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.2 | INTEGER | read-write | Setting this flag to 'enabled' will allow manual IP address configuration but disallow any DHCP configuration. |
| INT hpicfIpv6InterfaceAutoConfig | 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.3 | INTEGER | read-write | Setting this flag to 'enabled' will allow host to configure automatically from default router. There may be multiple routers and in that scenario switch will add the addresses from all these routers |
| INT hpicfIpv6InterfaceDhcpRapidCommit | 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.4 | INTEGER | read-write | Setting this flag to 'enabled' will allow the host to get address and configuration information from the dhcp server rapidly. This flag can be enabled only if the hpicfIpv6InterfaceDhcpMode object is set as dhcpFull. By default this flag is set to disabled. |
| INT hpicfIpv6InterfaceDhcpRelay | 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.5 | INTEGER | read-write | This flag indicates whether this interface is dhcp-relay enabled. By default this flag is set to disabled. |
| INT hpicfIpv6InterfaceCfgEnableStatus | 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.6 | INTEGER | read-write | The indication of whether IPv6 is enabled (up) or disabled (down) on this interface. Setting this object to up(1) will enable ipv6 for the given interface.Setting this object to down(2) will disable the ipv6 for the interface only if hpicfIpv6InterfaceDhcpMode, hpicfIpv6InterfaceManual and hpicfIpv6InterfaceAutoConfig are disabled.A get on this object reflects the data saved in a non-volatile storage. Note:To get the current ipv6 status for an interface refer to ipv6InterfaceEnableStatus. |
| I32 hpicfIpv6InterfaceDadAttempts | 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.7 | Integer32 | read-write | This object indicates the maximum number of neighbor solicitation requests that will be sent while performing duplicate address detection for this interface. Note: hpicfIpv6NDDadAttempts object's value will be in use for dad attempts for this interface when hpicfIpv6InterfaceDadAttemptsMode is 'global'. |
| INT hpicfIpv6InterfaceDadAttemptsMode | 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.8 | INTEGER | read-write | This object indicates whether the value in hpicfIpv6NDDadAttempts is in use or the value in hpicfIpv6InterfaceDadAttempts is in use for an entry in this table while performing duplicate address detection. A set to 'global' means: - hpicfIpv6NDDadAttempts value will be used for dad attempts. A set to 'perInterface' means: - hpicfIpv6InterfaceDadAttempts value will be used for dad attempts. |
| U32 hpicfIpv6InterfaceReachableTime | 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.9 | Unsigned32 | read-write | The time a neighbor is considered reachable after receiving a reachability confirmation. |
| U32 hpicfIpv6InterfaceRetransmitTime | 1.3.6.1.4.1.11.2.14.11.1.10.3.2.1.1.10 | Unsigned32 | read-write | The time between retransmissions of Neighbor Solicitation messages to a neighbor when resolving the address or when probing the reachability of a neighbor. |
RFC description
HP IP configuration management for IPv4/IPv6 addressing, interface settings, UDP tunneling, and ARP client tracking on network devices.
Start monitoring HP ProCurve switch (basic IP address/interface configuration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.