All MIBs › EdgeSwitch-ROUTING6-MIB
Organization: Broadcom Inc
Last Updated: 2011-01-26
Category: Technology: IPv6, Vendor: EdgeSwitch/Ubiquiti
Description: Ubiquiti EdgeSwitch IPv6 routing MIB for managing IPv6 static routes, router advertisements, and IPv6 forwarding.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is EdgeSwitch-ROUTING6-MIB?
EdgeSwitch-ROUTING6-MIB is a private Ubiquiti Networks MIB module for the FastPath-based EdgeSwitch line, covering IPv6 routing functionality. It exposes configuration and state for IPv6 static routes, router advertisement (RA) parameters, and IPv6 forwarding behavior on the switch. Rather than hardware health, its monitoring value is mainly in software/protocol status: whether IPv6 forwarding is enabled, whether the route table matches the intended design, and whether router advertisements are being sent as configured, which helps detect misconfigured or stalled IPv6 routing. It builds on the FastPath routing MIB conventions common across Broadcom-based switch silicon and is typically used alongside the standard IP-MIB and IPv6 MIBs rather than in isolation. It is deployed on Ubiquiti EdgeSwitch and EdgeMax devices in SMB and prosumer networks running dual-stack IPv4/IPv6, where the EdgeSwitch-ROUTING6-MIB MIB exposes IPv6 routing state via SNMP.
IPNetwork Monitor allows you to monitor SNMP objects defined in EdgeSwitch-ROUTING6-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Ubiquiti EdgeSwitch
- Ubiquiti EdgeMax network switch
Monitoring Examples
No sample objects were provided for this module in the source, so specific object or table names cannot be confirmed here. In practice a MIB of this kind would be expected to expose an IPv6 static route table and RA configuration objects, and an administrator would poll them to confirm that configured routes are active and that RA intervals match the intended network design. An anomaly such as a missing expected route or an unexpectedly disabled forwarding flag would indicate a configuration drift or a routing failure.
What Can Be Monitored
- IPv6 static route configuration
- IPv6 forwarding enable state
- router advertisement configuration
- IPv6 routing table status
This MIB depends on
Related MIBs
Imported Objects
From EdgeSwitch-REF-MIB
| fastPath | OBJECT-IDENTITY |
From IPV6-TC
| Ipv6Address | |
| Ipv6AddressIfIdentifier | |
| Ipv6AddressPrefix | |
| Ipv6IfIndex | |
| Ipv6IfIndexOrZero |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| PhysAddress | |
| RowPointer | |
| RowStatus | |
| TimeStamp | |
| TruthValue | |
| VariablePointer |
How to Use in IPNetwork Monitor
Example using agentIpv6RouteAdds OID:
Select an Ubiquiti EdgeSwitch (Broadcom FastPath-based) switch (IPv6 routing/RA config) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type agentIpv6RouteAdds into the Find box to locate it in the OID tree, then select it and click OK. The number of routes added to the IPv6 routing table. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| fastPathRoutingIpv6 | 1.3.6.1.4.1.4413.1.1.30 | The Ubiquiti Private MIB for FastPath Ipv6 Routing | ||
| agentIpv6Group | 1.3.6.1.4.1.4413.1.1.30.1 | |||
| INT agentIpv6RoutingMode | 1.3.6.1.4.1.4413.1.1.30.1.1 | INTEGER | read-write | Administratively enables/disables ipv6 unicast routing on the switch. |
| agentIpv6InterfaceTable | 1.3.6.1.4.1.4413.1.1.30.1.2 | not-accessible | ||
| agentIpv6InterfaceEntry | 1.3.6.1.4.1.4413.1.1.30.1.2.1 | not-accessible | ||
| I32 agentIpv6InterfaceIfIndex | 1.3.6.1.4.1.4413.1.1.30.1.2.1.1 | Integer32 | read-only | The IfIndex associated with this instance. |
| U32 agentIpv6InterfaceMtuValue | 1.3.6.1.4.1.4413.1.1.30.1.2.1.2 | Unsigned32 | read-write | Configures the MTU value for this interface.If it is not yet configured, retrieving the value of this object results in a zero value. Setting the value zero to this object effectively un-configures the MTU. |
| I32 agentIpv6InterfaceDadTransmits | 1.3.6.1.4.1.4413.1.1.30.1.2.1.3 | Integer32 | read-write | Configures the dad transmits value for this interface. |
| INT agentIpv6InterfaceLinkLocalOnly | 1.3.6.1.4.1.4413.1.1.30.1.2.1.4 | INTEGER | read-write | When enabled, interface is capable of ipv6 operation without a global address. In this case, an eui-64 based link-local address is used. |
| INT agentIpv6InterfaceIcmpUnreachables | 1.3.6.1.4.1.4413.1.1.30.1.2.1.5 | INTEGER | read-write | If this object is enable, it indicates that ICMPv6 unreachables can be sent on this interface. |
| INT agentIpv6InterfaceAutoconfig | 1.3.6.1.4.1.4413.1.1.30.1.2.1.6 | INTEGER | read-write | If this object is enabled, it indicates that the IPv6 address is automatically generated using IPv6 stateless address auto configuration. |
| INT agentIpv6InterfaceDhcpClient | 1.3.6.1.4.1.4413.1.1.30.1.2.1.7 | INTEGER | read-write | If this object is enabled, the interface uses DHCPv6 Client protocol to acquire an IPv6 address. |
| INT agentIpv6InterfaceIcmpRedirects | 1.3.6.1.4.1.4413.1.1.30.1.2.1.8 | INTEGER | read-write | Enable/Disable the sending of ICMPv6 redirect messages in the redirect scenario where the forwarded packet is sent out through the same interface on which the packet was received. |
| agentIpv6RouterAdvertisementTable | 1.3.6.1.4.1.4413.1.1.30.1.3 | not-accessible | There is no global administrative flag for router advertisement. The global routing flag (agentIpv6RoutingMode) will be used for this purpose. If routing is disabled, router advertisement is disabled as well. | |
| agentIpv6RouterAdvertisementEntry | 1.3.6.1.4.1.4413.1.1.30.1.3.1 | not-accessible | ||
| I32 agentIpv6RouterAdvertisementIfIndex | 1.3.6.1.4.1.4413.1.1.30.1.3.1.1 | Integer32 | read-only | Interface Number to configure Router Advertisement on. |
| INT agentIpv6RouterAdvertisementSuppressMode | 1.3.6.1.4.1.4413.1.1.30.1.3.1.2 | INTEGER | read-write | Enable or disable router advertisement suppression on the interface. |
| I32 agentIpv6RouterAdvertisementMaxAdvertisementInterval | 1.3.6.1.4.1.4413.1.1.30.1.3.1.3 | Integer32 | read-write | Maximum time allowed between sending router advertisements from the interface. |
| I32 agentIpv6RouterAdvertisementAdvertisementLifetime | 1.3.6.1.4.1.4413.1.1.30.1.3.1.4 | Integer32 | read-write | Value of lifetime field of router advertisement sent from the interface. This value must be greater than or equal to agentIpv6RouterAdvertisementMaxAdvertisementInterval. |
| I32 agentIpv6RouterAdvertisementNbrSolicitInterval | 1.3.6.1.4.1.4413.1.1.30.1.3.1.5 | Integer32 | read-write | Value of retrans time field of router advertisement sent from the interface. A value of 0 means this router does not specifiy the interval. |
| I32 agentIpv6RouterAdvertisementReachableTime | 1.3.6.1.4.1.4413.1.1.30.1.3.1.6 | Integer32 | read-write | Value of reachable time field of router advertisement sent from the interface. A value of 0 means this router does not specifiy the interval. |
| INT agentIpv6RouterAdvertisementManagedFlag | 1.3.6.1.4.1.4413.1.1.30.1.3.1.7 | INTEGER | read-write | Value of managed config field of router advertisement sent from the interface. |
| INT agentIpv6RouterAdvertisementOtherFlag | 1.3.6.1.4.1.4413.1.1.30.1.3.1.8 | INTEGER | read-write | Value of other config field of router advertisement sent from the interface. |
| INT agentIpv6RouterAdvertisementHopLimitUnspecifiedMode | 1.3.6.1.4.1.4413.1.1.30.1.3.1.9 | INTEGER | read-write | This object configures the router to send Router Advertisements on an interface with unspecified (0) Current Hop Limit value. This will tell the hosts on that link to ignore the Hop Limit from this Router. |
| agentIpv6AddrPrefixTable | 1.3.6.1.4.1.4413.1.1.30.1.4 | not-accessible | The list of IPv6 address prefixes of IPv6 interfaces. | |
| agentIpv6AddrPrefixEntry | 1.3.6.1.4.1.4413.1.1.30.1.4.1 | not-accessible | An interface entry containing objects of a particular IPv6 address prefix. | |
| ADR agentIpv6AddrPrefix | 1.3.6.1.4.1.4413.1.1.30.1.4.1.1 | Ipv6AddressPrefix | not-accessible | The prefix associated with the this interface. |
| INT agentIpv6AddrPrefixLength | 1.3.6.1.4.1.4413.1.1.30.1.4.1.2 | INTEGER | not-accessible | The length of the prefix (in bits). |
| T/F agentIpv6AddrPrefixOnLinkFlag | 1.3.6.1.4.1.4413.1.1.30.1.4.1.3 | TruthValue | read-write | This object has the value 'true(1)', if this prefix can be used for on-link determination and the value 'false(2)' otherwise. |
| T/F agentIpv6AddrPrefixAutonomousFlag | 1.3.6.1.4.1.4413.1.1.30.1.4.1.4 | TruthValue | read-write | Autonomous address configuration flag. When true(1), indicates that this prefix can be used for autonomous address configuration (i.e. can be used to form a local interface address). If false(2), it is not used to autoconfigure a local interface address. |
| U32 agentIpv6AddrPrefixAdvPreferredLifetime | 1.3.6.1.4.1.4413.1.1.30.1.4.1.5 | Unsigned32 | read-write | It is the length of time in seconds that this prefix will remain preferred, i.e. time until deprecation. A value of 4,294,967,295 represents infinity. The address generated from a deprecated prefix should no longer be used as a source address in new communications, but packets received on such an interface are processed as expected. |
| U32 agentIpv6AddrPrefixAdvValidLifetime | 1.3.6.1.4.1.4413.1.1.30.1.4.1.6 | Unsigned32 | read-write | It is the length of time in seconds that this prefix will remain valid, i.e. time until invalidation. A value of 4,294,967,295 represents infinity. The address generated from an invalidated prefix should not appear as the destination or source address of a packet. |
| agentIpv6AddrTable | 1.3.6.1.4.1.4413.1.1.30.1.5 | not-accessible | The table of addressing information relevant to this node's interface addresses. | |
| agentIpv6AddrEntry | 1.3.6.1.4.1.4413.1.1.30.1.5.1 | not-accessible | The addressing information for one of this node's interface addresses. | |
| ADR agentIpv6AddrAddress | 1.3.6.1.4.1.4413.1.1.30.1.5.1.1 | Ipv6Address | not-accessible | The IPv6 address to which this entry's addressing information pertains. |
| INT agentIpv6AddrPfxLength | 1.3.6.1.4.1.4413.1.1.30.1.5.1.2 | INTEGER | read-create | The length of the prefix (in bits) associated with the IPv6 address of this entry. |
| T/F agentIpv6AddrEui64Flag | 1.3.6.1.4.1.4413.1.1.30.1.5.1.3 | TruthValue | read-create | This object has the value 'true(1)', if this address uses and eui-64 generated interface identifier and the value 'false(2)' otherwise. |
| ROW agentIpv6AddrStatus | 1.3.6.1.4.1.4413.1.1.30.1.5.1.4 | RowStatus | read-create | Creates a new entry in the Address table. Allowed values are: createAndGo(4) - Creates an entry in this table, associating the address with a given interface. The agentIpv6NetMask object must be set during creation. destroy(6) - Removes the associated address from the interface. |
| agentIpv6StaticRouteTable | 1.3.6.1.4.1.4413.1.1.30.1.6 | not-accessible | IPv6 Static Routing table. This table contains an entry for each valid IPv6 static unicast route that can be used for packet forwarding determination. | |
| agentIpv6StaticRouteEntry | 1.3.6.1.4.1.4413.1.1.30.1.6.1 | not-accessible | A routing entry. | |
| ADR agentIpv6StaticRouteDest | 1.3.6.1.4.1.4413.1.1.30.1.6.1.1 | Ipv6AddressPrefix | not-accessible | The destination IPv6 address of this route. This object may not take a Multicast address value. |
| INT agentIpv6StaticRoutePfxLength | 1.3.6.1.4.1.4413.1.1.30.1.6.1.2 | INTEGER | not-accessible | Indicates the prefix length of the destination address. |
| IPV agentIpv6StaticRouteIfIndex | 1.3.6.1.4.1.4413.1.1.30.1.6.1.3 | Ipv6IfIndexOrZero | not-accessible | The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ipv6IfIndex. For routes with global address next hop this value can be zero. |
| ADR agentIpv6StaticRouteNextHop | 1.3.6.1.4.1.4413.1.1.30.1.6.1.4 | Ipv6Address | not-accessible | The address of the next system en route. |
| INT agentIpv6StaticRoutePreference | 1.3.6.1.4.1.4413.1.1.30.1.6.1.5 | INTEGER | read-create | The routing preference metric for this route. A lower value is more preferred. |
| ROW agentIpv6StaticRouteStatus | 1.3.6.1.4.1.4413.1.1.30.1.6.1.6 | RowStatus | read-create | Creates a new entry in the Address table. Allowed values are: createAndGo(4) - Creates an entry in this table. destroy(6) - Removes the associated route from the interface. |
| agentIpv6ServicePortGroup | 1.3.6.1.4.1.4413.1.1.30.1.7 | |||
| agentIpv6ServicePortPrefixTable | 1.3.6.1.4.1.4413.1.1.30.1.7.1 | not-accessible | IPv6 Service Port Prefix Table. This table contains an entry for each valid IPv6 prefix configured on the Service Port. | |
| agentIpv6ServicePortPrefixEntry | 1.3.6.1.4.1.4413.1.1.30.1.7.1.1 | not-accessible | An IPv6 Service Port Prefix entry. | |
| U32 agentIpv6ServicePortPrefixIndex | 1.3.6.1.4.1.4413.1.1.30.1.7.1.1.1 | Unsigned32 | not-accessible | The index of the Ipv6 Prefix Address configured on the Service Port. Removal of a row will cause index values to be reassigned. |
| ADR agentIpv6ServicePortPrefix | 1.3.6.1.4.1.4413.1.1.30.1.7.1.1.2 | Ipv6Address | read-only | The Ipv6 Prefix Address configured on the Service Port. |
| U32 agentIpv6ServicePortPrefixLength | 1.3.6.1.4.1.4413.1.1.30.1.7.1.1.3 | Unsigned32 | read-only | The length of the IPv6 Prefix Address. |
| agentIpv6ServicePortDefaultRouterTable | 1.3.6.1.4.1.4413.1.1.30.1.7.2 | not-accessible | IPv6 Service Port Default Router Table. This table contains an entry for each valid IPv6 Default Router configured on the Service Port. | |
| agentIpv6ServicePortDefaultRouterEntry | 1.3.6.1.4.1.4413.1.1.30.1.7.2.1 | not-accessible | An IPv6 Service Port Default Router entry. | |
| U32 agentIpv6ServicePortDefaultRouterIndex | 1.3.6.1.4.1.4413.1.1.30.1.7.2.1.1 | Unsigned32 | not-accessible | The index of the IPv6 Default Router Address configured on the Service Port. Removal of a row will cause index values to be reassigned. |
| ADR agentIpv6ServicePortDefaultRouter | 1.3.6.1.4.1.4413.1.1.30.1.7.2.1.2 | Ipv6Address | read-only | The Address of the IPv6 Default Router configured on the Service Port. |
| agentIpv6ServicePortNbrTable | 1.3.6.1.4.1.4413.1.1.30.1.7.3 | not-accessible | IPv6 Service Port Neighbor Table. This table contains an entry for each valid IPv6 Neighbor configured on the Service Port. | |
| agentIpv6ServicePortNbrEntry | 1.3.6.1.4.1.4413.1.1.30.1.7.3.1 | not-accessible | An IPv6 Service Port Neighbor entry. | |
| ADR agentIpv6ServicePortNbrAddr | 1.3.6.1.4.1.4413.1.1.30.1.7.3.1.1 | Ipv6Address | not-accessible | The Ipv6 Address of a neighbor switch visible to the Service Port. |
| MAC agentIpv6ServicePortNbrPhysAddr | 1.3.6.1.4.1.4413.1.1.30.1.7.3.1.2 | MacAddress | read-only | The MacAddress of the neighboring switch. |
| INT agentIpv6ServicePortNbrState | 1.3.6.1.4.1.4413.1.1.30.1.7.3.1.3 | INTEGER | read-only | The state of the neighboring switch: reachable(1) - The neighbor is reachable by this switch. stale(2) - Information about the neighbor is scheduled for deletion. delay(3) - No information has been received from neighbor during delay period. probe(4) - Switch is attempting to probe for this neighbor. unknown(6) - Unknown status. |
| TIM agentIpv6ServicePortNbrUpdated | 1.3.6.1.4.1.4413.1.1.30.1.7.3.1.4 | TimeStamp | read-only | The last sysUpTime that this neighbor has been updated. |
| T/F agentIpv6ServicePortNbrIsRouter | 1.3.6.1.4.1.4413.1.1.30.1.7.3.1.5 | TruthValue | read-only | Returns true(1) if the neighbor machine is a router, false(2) otherwise. |
| INT agentIpv6ServicePortNbrType | 1.3.6.1.4.1.4413.1.1.30.1.7.3.1.6 | INTEGER | read-only | The type of the mapping. The 'dynamic(2)' type indicates that the IPv6 address to physical addresses mapping has been dynamically resolved using the IPv6 Neighbor Discovery protocol. The static(3)' types indicates that the mapping has been statically configured. The local(4) indicates that the mapping is provided for an entity's own interface address. |
| agentIpv6ServicePortNbrCfgTable | 1.3.6.1.4.1.4413.1.1.30.1.7.4 | not-accessible | The table contains an entry for each static IPv6 Neighbor on the Service Port. | |
| agentIpv6ServicePortNbrCfgEntry | 1.3.6.1.4.1.4413.1.1.30.1.7.4.1 | not-accessible | An entry of the static IPv6 Neighbor on the Service Port. | |
| ADR agentIpv6ServicePortNbrCfgAddr | 1.3.6.1.4.1.4413.1.1.30.1.7.4.1.1 | Ipv6Address | not-accessible | The Ipv6 Address of a static neighbor on the Service Port. |
| MAC agentIpv6ServicePortNbrCfgPhysAddr | 1.3.6.1.4.1.4413.1.1.30.1.7.4.1.2 | MacAddress | read-create | The MAC Address of a static neighbor on the Service Port. |
| ROW agentIpv6ServicePortNbrCfgEntryStatus | 1.3.6.1.4.1.4413.1.1.30.1.7.4.1.3 | RowStatus | read-create | Create or delete the static neighbor entry on the Service Port. The configured static neighbor entry is always active. |
| agentIpv6IcmpControlGroup | 1.3.6.1.4.1.4413.1.1.30.1.8 | |||
| I32 agentIpv6IcmpRateLimitInterval | 1.3.6.1.4.1.4413.1.1.30.1.8.1 | Integer32 | read-write | Specifies the time interval between tokens being placed in the bucket for ICMP Ratelimit. |
| I32 agentIpv6IcmpRateLimitBurstSize | 1.3.6.1.4.1.4413.1.1.30.1.8.2 | Integer32 | read-write | Specifies the number of tokens to be placed after timeout. |
| agentDhcp6ClientParametersTable | 1.3.6.1.4.1.4413.1.1.30.1.9 | not-accessible | Information about the DHCPv6 Client parameters on the interfaces. | |
| agentDhcp6ClientParametersEntry | 1.3.6.1.4.1.4413.1.1.30.1.9.1 | not-accessible | DHCPv6 Client information on an interface. | |
| U32 agentDhcp6ClientInterfaceIndex | 1.3.6.1.4.1.4413.1.1.30.1.9.1.1 | Unsigned32 | read-only | The Interface index on which the IPv6 address is leased by the DHCPv6 Server. |
| ADR agentDhcp6ClientPrefix | 1.3.6.1.4.1.4413.1.1.30.1.9.1.2 | Ipv6AddressPrefix | read-only | The IPv6 Prefix leased by the DHCPv6 Server. |
| INT agentDhcp6ClientPrefixlength | 1.3.6.1.4.1.4413.1.1.30.1.9.1.3 | INTEGER | read-only | The Prefix length corresponding to the IPv6 Prefix leased by the DHCPv6 Server. |
| INT agentDhcp6ClientState | 1.3.6.1.4.1.4413.1.1.30.1.9.1.4 | INTEGER | read-only | The State of the DHCPv6 Client on this interface. |
| STR agentDhcp6ClientServerDUID | 1.3.6.1.4.1.4413.1.1.30.1.9.1.5 | DisplayString | read-only | The DHCPv6 Unique Identifier of the DHCPv6 Server on this interface. |
| U32 agentDhcp6ClientT1Time | 1.3.6.1.4.1.4413.1.1.30.1.9.1.6 | Unsigned32 | read-only | The T1 (in seconds) time as indicated by the DHCPv6 Server. T1 value indicates the time interval after which the address is requested for renewal. |
| U32 agentDhcp6ClientT2Time | 1.3.6.1.4.1.4413.1.1.30.1.9.1.7 | Unsigned32 | read-only | The T2 (in seconds) time as indicated by the DHCPv6 Server. T2 value indicates the time interval after which the Client sends Rebind message to the Server incase there are no replies to the Renew messages. |
| U32 agentDhcp6ClientIAID | 1.3.6.1.4.1.4413.1.1.30.1.9.1.8 | Unsigned32 | read-only | An identifier for an identity association chosen by this Client. |
| U32 agentDhcp6ClientPreferredLifeTime | 1.3.6.1.4.1.4413.1.1.30.1.9.1.9 | Unsigned32 | read-only | The time (in seconds) that the IPv6 address is leased by the DHCPv6 Server. |
| U32 agentDhcp6ClientValidLifeTime | 1.3.6.1.4.1.4413.1.1.30.1.9.1.10 | Unsigned32 | read-only | The time (in seconds) that the IPv6 address is leased by the DHCPv6 Server. |
| U32 agentDhcp6ClientRenewTime | 1.3.6.1.4.1.4413.1.1.30.1.9.1.11 | Unsigned32 | read-only | The time (in seconds) remaining to send a DHCPv6 Renew request to DHCPv6 Server for the leased address. |
| U32 agentDhcp6ClientExpireTime | 1.3.6.1.4.1.4413.1.1.30.1.9.1.12 | Unsigned32 | read-only | The time (in seconds) when the DHCPv6 leased address expires. |
| agentIpv6RoutingTableSummaryGroup | 1.3.6.1.4.1.4413.1.1.30.1.10 | |||
| G32 agentIpv6ConnectedRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.1 | Gauge32 | read-only | The number of connected routes in the IPv6 routing table. |
| G32 agentIpv6StaticRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.2 | Gauge32 | read-only | The number of static routes in the IPv6 routing table. |
| G32 agentIpv66to4Routes | 1.3.6.1.4.1.4413.1.1.30.1.10.3 | Gauge32 | read-only | The number of 6to4 routes in the IPv6 routing table. |
| G32 agentIpv6OspfRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.4 | Gauge32 | read-only | The number of OSPFv2 routes in the IPv6 routing table. |
| G32 agentIpv6OspfIntraRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.5 | Gauge32 | read-only | The number of OSPFv2 intra-area routes in the IPv6 routing table. |
| G32 agentIpv6OspfInterRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.6 | Gauge32 | read-only | The number of OSPFv2 inter-area routes in the IPv6 routing table. |
| G32 agentIpv6OspfExt1Routes | 1.3.6.1.4.1.4413.1.1.30.1.10.7 | Gauge32 | read-only | The number of OSPFv2 external type 1 routes in the IPv6 routing table. |
| G32 agentIpv6OspfExt2Routes | 1.3.6.1.4.1.4413.1.1.30.1.10.8 | Gauge32 | read-only | The number of OSPFv2 external type 2 routes in the IPv6 routing table. |
| G32 agentIpv6BgpRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.9 | Gauge32 | read-only | The number of BGP routes in the IPv6 routing table. |
| G32 agentIpv6EbgpRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.10 | Gauge32 | read-only | The number of external BGP routes in the IPv6 routing table. |
| G32 agentIpv6IbgpRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.11 | Gauge32 | read-only | The number of internal BGP routes in the IPv6 routing table. |
| G32 agentIpv6LocalBgpRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.12 | Gauge32 | read-only | The number of local BGP routes in the IPv6 routing table. |
| G32 agentIpv6RejectRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.13 | Gauge32 | read-only | The number of reject routes in the IPv6 routing table. |
| G32 agentIpv6TotalRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.14 | Gauge32 | read-only | The number of routes in the IPv6 routing table. |
| G32 agentIpv6BestRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.15 | Gauge32 | read-only | The number of IPv6 routes in the forwarding table. |
| G32 agentIpv6BestRoutesHigh | 1.3.6.1.4.1.4413.1.1.30.1.10.16 | Gauge32 | read-only | The highest number of IPv6 routes in the forwarding table. |
| G32 agentIpv6AlternateRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.17 | Gauge32 | read-only | The number of alternate routes in the IPv6 routing table. An alternate route is less preferred than the best route and is not used for forwarding. |
| C32 agentIpv6RouteAddsEx | 1.3.6.1.4.1.4413.1.1.30.1.10.18 | Counter32 | read-only | The number of routes added to the IPv6 routing table. |
| C32 agentIpv6RouteModifies | 1.3.6.1.4.1.4413.1.1.30.1.10.19 | Counter32 | read-only | The number of routes changed in the IPv6 routing table. |
| C32 agentIpv6RouteDeletes | 1.3.6.1.4.1.4413.1.1.30.1.10.20 | Counter32 | read-only | The number of routes removed from the IPv6 routing table. |
| C32 agentIpv6UnresolvedRouteAdds | 1.3.6.1.4.1.4413.1.1.30.1.10.21 | Counter32 | read-only | The number of IPv6 route adds that failed because none of the route's next hops were on a local subnet. |
| C32 agentIpv6InvalidRouteAdds | 1.3.6.1.4.1.4413.1.1.30.1.10.22 | Counter32 | read-only | The number of IPv6 routes adds that failed because the route was invalid. |
| C32 agentIpv6FailedRouteAdds | 1.3.6.1.4.1.4413.1.1.30.1.10.23 | Counter32 | read-only | The number of IPv6 routes adds that failed because of a resource limitation in the routing table |
| G32 agentIpv6ReservedLocals | 1.3.6.1.4.1.4413.1.1.30.1.10.24 | Gauge32 | read-only | The number of IPv6 routing table entries reserved for a local subnet on a routing interface that is down. |
| G32 agentIpv6UniqueNextHops | 1.3.6.1.4.1.4413.1.1.30.1.10.25 | Gauge32 | read-only | The number of distinct next hops used among all IPv6 routes currently in the routing table. These include local interfaces for local routes and neighbors for indirect routes. |
| G32 agentIpv6UniqueNextHopsHigh | 1.3.6.1.4.1.4413.1.1.30.1.10.26 | Gauge32 | read-only | The highest count of unique next hops since counters were last cleared. |
| G32 agentIpv6NextHopGroups | 1.3.6.1.4.1.4413.1.1.30.1.10.27 | Gauge32 | read-only | The current number of next hop groups in use by one or more routes. Each next hop group includes one or more next hops. |
| G32 agentIpv6NextHopGroupsHigh | 1.3.6.1.4.1.4413.1.1.30.1.10.28 | Gauge32 | read-only | The highest count of next hop groups since counters were last cleared. |
| G32 agentIpv6EcmpGroups | 1.3.6.1.4.1.4413.1.1.30.1.10.29 | Gauge32 | read-only | The number of next hop groups with multiple next hops. |
| G32 agentIpv6EcmpGroupsHigh | 1.3.6.1.4.1.4413.1.1.30.1.10.30 | Gauge32 | read-only | The high water mark of the number of ECMP groups. |
| G32 agentIpv6EcmpRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.31 | Gauge32 | read-only | The current number of IPv6 routes with multiple next hops. |
| G32 agentIpv6TruncEcmpRoutes | 1.3.6.1.4.1.4413.1.1.30.1.10.32 | Gauge32 | read-only | The number of ECMP routes that are currently installed in the forwarding table with just one next hop. The forwarding table may limit the number of ECMP routes or the number of ECMP groups. When an ECMP route cannot be installed because such a limit is reached, the route is installed with a single next hop. |
| C32 agentIpv6EcmpRetries | 1.3.6.1.4.1.4413.1.1.30.1.10.33 | Counter32 | read-only | The number of ECMP routes that have been installed in the forwarding table after initially being installed with a single next hop. |
| agentIpv6EcmpCountTable | 1.3.6.1.4.1.4413.1.1.30.1.11 | not-accessible | A count of the number of routes with each number of ECMP next hops. A walk of this table only returns the entries with a non-zero value for agentIpv6EcmpRouteCount. | |
| agentIpv6EcmpCountEntry | 1.3.6.1.4.1.4413.1.1.30.1.11.1 | not-accessible | Number of IPv6 routes with a given number of next hops. | |
| U32 agentIpv6EcmpNextHopCount | 1.3.6.1.4.1.4413.1.1.30.1.11.1.1 | Unsigned32 | not-accessible | The number of next hops in a route. From 0 to the maximum number of next hops in an ECMP route. The maximum varies by platform. |
| G32 agentIpv6EcmpRouteCount | 1.3.6.1.4.1.4413.1.1.30.1.11.1.2 | Gauge32 | read-only | The number of IPv6 routes with agentIpv6EcmpNextHopCount next hops. |
| agentIpv6NetworkPortGroup | 1.3.6.1.4.1.4413.1.1.30.1.12 | |||
| agentIpv6NetworkPortNbrTable | 1.3.6.1.4.1.4413.1.1.30.1.12.1 | not-accessible | IPv6 Network Port Neighbor Table. This table contains an entry for each valid IPv6 Neighbor configured on the Network Port. | |
| agentIpv6NetworkPortNbrEntry | 1.3.6.1.4.1.4413.1.1.30.1.12.1.1 | not-accessible | An IPv6 Network Port Neighbor entry. | |
| ADR agentIpv6NetworkPortNbrAddr | 1.3.6.1.4.1.4413.1.1.30.1.12.1.1.1 | Ipv6Address | not-accessible | The Ipv6 Address of a neighbor switch visible to the Network Port. |
| MAC agentIpv6NetworkPortNbrPhysAddr | 1.3.6.1.4.1.4413.1.1.30.1.12.1.1.2 | MacAddress | read-only | The MacAddress of the neighboring switch. |
| INT agentIpv6NetworkPortNbrState | 1.3.6.1.4.1.4413.1.1.30.1.12.1.1.3 | INTEGER | read-only | The state of the neighboring switch: reachable(1) - The neighbor is reachable by this switch. stale(2) - Information about the neighbor is scheduled for deletion. delay(3) - No information has been received from neighbor during delay period. probe(4) - Switch is attempting to probe for this neighbor. unknown(6) - Unknown status. |
| TIM agentIpv6NetworkPortNbrUpdated | 1.3.6.1.4.1.4413.1.1.30.1.12.1.1.4 | TimeStamp | read-only | The last sysUpTime that this neighbor has been updated. |
| T/F agentIpv6NetworkPortNbrIsRouter | 1.3.6.1.4.1.4413.1.1.30.1.12.1.1.5 | TruthValue | read-only | Returns true(1) if the neighbor machine is a router, false(2) otherwise. |
| INT agentIpv6NetworkPortNbrType | 1.3.6.1.4.1.4413.1.1.30.1.12.1.1.6 | INTEGER | read-only | The type of the mapping. The 'dynamic(2)' type indicates that the IPv6 address to physical addresses mapping has been dynamically resolved using the IPv6 Neighbor Discovery protocol. The static(3)' types indicates that the mapping has been statically configured. The local(4) indicates that the mapping is provided for an entity's own interface address. |
| agentIpv6NetworkPortNbrCfgTable | 1.3.6.1.4.1.4413.1.1.30.1.12.2 | not-accessible | The table contains an entry for each static IPv6 Neighbor on the Network Port. | |
| agentIpv6NetworkPortNbrCfgEntry | 1.3.6.1.4.1.4413.1.1.30.1.12.2.1 | not-accessible | An entry of the static IPv6 Neighbor on the Network Port. | |
| ADR agentIpv6NetworkPortNbrCfgAddr | 1.3.6.1.4.1.4413.1.1.30.1.12.2.1.1 | Ipv6Address | not-accessible | The Ipv6 Address of a static neighbor on the Network Port. |
| MAC agentIpv6NetworkPortNbrCfgPhysAddr | 1.3.6.1.4.1.4413.1.1.30.1.12.2.1.2 | MacAddress | read-create | The MAC Address of a static neighbor on the Network Port. |
| ROW agentIpv6NetworkPortNbrCfgEntryStatus | 1.3.6.1.4.1.4413.1.1.30.1.12.2.1.3 | RowStatus | read-create | Create or delete the static neighbor entry on the Network Port. The configured static neighbor entry is always active. |
| agentIpv6NbrCfgTable | 1.3.6.1.4.1.4413.1.1.30.1.13 | not-accessible | The table contains an entry for each static IPv6 Neighbor on the Network Port. | |
| agentIpv6NbrCfgEntry | 1.3.6.1.4.1.4413.1.1.30.1.13.1 | not-accessible | An entry of the static IPv6 Neighbor on the Network Port. | |
| IPV agentIpv6IfIndex | 1.3.6.1.4.1.4413.1.1.30.1.13.1.1 | Ipv6IfIndex | not-accessible | A unique non-zero value identifying the particular IPv6 interface. |
| ADR agentIpv6NbrCfgAddr | 1.3.6.1.4.1.4413.1.1.30.1.13.1.2 | Ipv6Address | not-accessible | The Ipv6 Address of a static neighbor on the Routing or Host interface. |
| MAC agentIpv6NbrCfgPhysAddr | 1.3.6.1.4.1.4413.1.1.30.1.13.1.3 | MacAddress | read-create | The MAC Address of a static neighbor on the Routing or Host interface. |
| ROW agentIpv6NbrCfgEntryStatus | 1.3.6.1.4.1.4413.1.1.30.1.13.1.4 | RowStatus | read-create | Create or delete the static neighbor entry on the Routing or Host interface. The configured static neighbor entry is always active. |
| INT agentIpv6NeighborsDynamicRenew | 1.3.6.1.4.1.4413.1.1.30.1.14 | INTEGER | read-write | Enables/disables the periodic NUD (neighbor unreachability detection) to be run on the existing IPv6 neighbor entries based on the activity of the entries in the hardware. If the setting is disabled, only those entries that are actively used in the hardware are triggered for NUD. If the setting is enabled, all the entries are triggered for NUD irrespective of their usage in the hardware. |
| I32 agentIpv6UnresolvedDataRateLimit | 1.3.6.1.4.1.4413.1.1.30.1.15 | Integer32 | read-write | The rate in packets-per-second for the number of IPv6 data packets trapped to CPU when the packet fails to be forwarded in the hardware due to unresolved hardware address of the destined IPv6 node. |
| I32 agentIpv6NUDMaxUnicastSolicits | 1.3.6.1.4.1.4413.1.1.30.1.16 | Integer32 | read-write | The maximum number of unicast Neighbor Solicitations sent during neighbor resolution or during NUD (neighbor unreachabililty detection) before switching to multicast Neighbor Solicitations. |
| I32 agentIpv6NUDMaxMulticastSolicits | 1.3.6.1.4.1.4413.1.1.30.1.17 | Integer32 | read-write | The maximum number of multicast Neighbor Solicitations sent during neighbor resolution or during NUD (neighbor unreachabililty detection). |
| I32 agentIpv6NUDBackoffMultiple | 1.3.6.1.4.1.4413.1.1.30.1.18 | Integer32 | read-write | The exponential backoff multiple to be used in the calculation of the next timeout value for Neighbor Solicitation transmission during NUD (neighbor unreachabililty detection) following the exponential backoff algorithm. The next timeout value is limited to a maximum value of 60 seconds if the value with exponential backoff calculation is greater than 60 seconds. |
RFC description
IPv6 unicast routing configuration and monitoring for EdgeSwitch, managing IPv6 interfaces and routing tables.
Start monitoring Ubiquiti EdgeSwitch (Broadcom FastPath-based) switch (IPv6 routing/RA config) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.