ETH-SWITCH-MIB

All MIBs › ETH-SWITCH-MIB

Category: Network Interfaces, Technology: Switching/L2, Vendor: Edgecore, Vendor: EtherWAN

Description: Provides generic SNMP management objects for Ethernet switch port, VLAN, and forwarding configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ETH-SWITCH-MIB?

ETH-SWITCH-MIB is a generically named MIB intended to provide basic SNMP management objects for Ethernet switch port, VLAN, and forwarding configuration; no module description or sample objects were available in source to confirm vendor-specific details. Based on its stated purpose, it would expose categories of data such as per-port administrative/operational state, VLAN membership, and Layer 2 forwarding-table entries. To the extent it covers port/link operational state, it would support basic hardware/interface status monitoring, such as detecting a port that has gone administratively or operationally down. No specific dependency on other MIBs (e.g., IF-MIB, BRIDGE-MIB) can be confirmed from the available context, though a generic Ethernet switch MIB of this kind would typically complement them. It would be deployed for basic Layer 2 switch configuration and status monitoring in a generic enterprise network. Engineers implementing or auditing this functionality typically reference the ETH-SWITCH-MIB RFC/standard documentation for the authoritative specification.

IPNetwork Monitor allows you to monitor SNMP objects defined in ETH-SWITCH-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

vendor-neutral or generic-vendor MIB, not confirmed to a specific manufacturer
Ethernet switches with port/VLAN management

Monitoring Examples

No object or table names were available in the source for this MIB, so specific identifiers cannot be cited with confidence; based on its stated scope, a realistic use would be polling per-port operational state and VLAN membership to confirm a port is up and correctly assigned before troubleshooting a connectivity complaint.

What Can Be Monitored

switch port administrative/operational state
VLAN membership/configuration
Layer 2 forwarding table entries

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
TimeTicks

From RFC1213-MIB

DisplayString

From SCANET-MIB

scanet

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
ethSwitch	1.3.6.1.4.1.208.39
NTF ethSwitchPermVioEvent	1.3.6.1.4.1.208.39.0.1			This trap is sent when there has been a permanent entry violation. A MAC address has been detected at an other port than the port where it has been configured as a permanent entry. The variable portIfIndex indicates the port where the MAC incorrectly has been detected. The problem can be solved by re-configuring the MAC's permanent entry, or by physical moving the MAC to the port it has been configured for.
NTF ethSwitchOnlyOneMACEvent	1.3.6.1.4.1.208.39.0.2			This trap is sent when a port detects more that one MAC address at a port intended for only one MAC. This Trap can only be sent from a Concentrator Switch where only one MAC is allowed, except from the network port. It can NOT be sent from a Backbone Switch since it allows multiple MAC's at all ports. The variable portIfIndex indicates the port where the MAC limit of one has bee exceeded. The problem can be solved by physical moving the MAC to a spare Concentrator Switch port.
NTF ethSwitchMACVioEvent	1.3.6.1.4.1.208.39.0.3			This trap is sent when there has been detected a MAC access control violation. A MAC address has been detected at a port with MAC access restriction, and the MAC was not allowed. The variable portIfIndex indicates the port with the MAC access violation.
NTF ethSwitchAdaptiveForwEvent	1.3.6.1.4.1.208.39.0.4			This trap is sent when a port automatically is changing forwarding mode. This will only happen when the port has been configured to Adaptive mode. The syntax is (Portnumber, New mode, Old mode) Mode numbers is: 2 = Cut-Through 3 = Fragment Free 4 = Store and Forward
NTF ethSwitchMACFilterVioEvent	1.3.6.1.4.1.208.39.0.5			Port/MAC filter MAC violation on port: %portIfIndex% This trap is sent when there has been detected a MAC address on a port (portIfIndex), where this MAC is not allowed access through the switch. Access restriction is due to entry in the Port/MAC filters of the switch.
control	1.3.6.1.4.1.208.39.1
INT scSegments	1.3.6.1.4.1.208.39.1.1	INTEGER	read-write	Object controlling the use of the System Center Backplane. Each bus is assigned a bit value in the object
INT defaultSwitchMode	1.3.6.1.4.1.208.39.1.2	INTEGER	read-write	Default Switch mode. used by the object portSwitchMode when its value is default(1)
INT defaultThrottleBackMode	1.3.6.1.4.1.208.39.1.3	INTEGER	read-write	Default ThrottleBack mode. used by the object portThrottleBack when its value is default(1)
INT networkPort	1.3.6.1.4.1.208.39.1.4	INTEGER	read-write	For a Workgroup Switch (only one multi MAC address port), this object determines the network port. The value equals the value of portNumber in the portTable. Notice that this object is valid for Workgroup switches only (ES-2410 and ES-1810). Other types of Switches returns the value 0 and has read-only access.
PRO expansionModule	1.3.6.1.4.1.208.39.2.1	ProductIds	read-only	An ID that identifies the expansion module
ports	1.3.6.1.4.1.208.39.3
TIK portLastChange	1.3.6.1.4.1.208.39.3.1	TimeTicks	read-only	The value of sysUpTime at the last time any interface has changed state
portTable	1.3.6.1.4.1.208.39.3.2		not-accessible	Port Table.
portEntry	1.3.6.1.4.1.208.39.3.2.1		not-accessible	A Port entry containing object for a Switch port.
INT portNumber	1.3.6.1.4.1.208.39.3.2.1.1	INTEGER	read-only	A number that uniquely identifies a port
INT portInterfaceIndex	1.3.6.1.4.1.208.39.3.2.1.2	INTEGER	read-only	The value of this object equals the ports interface index value, ex. portIfIndex. If the value of this object is zero, then the port is not active, i.e. does not appear in the portIfTable.
OCT portLED	1.3.6.1.4.1.208.39.3.2.1.3	OCTET STRING	read-only	The value of this object represent the status (colour) of the LED(s) attached to this port. Lower 3 bits indicates off/colour (off(0), red(1), green(2), yellow(4)), Higher 5 bits reserved for flash frequency. For value 0-9 the resolution is 0.1 Hz and 10-31 the resolution is 1.0 Hz. Ex. 8 gives 0.8 Hz and 11 gives 2 Hz. For PIM slots with two LEDs that can contain either an expansion card, a one port PIM or a PIM with multiple ports a special case is needed. The two LEDs are mapped into a two LED octets. In case the PIM slot contain a PIM with multiple ports a third LED octet represent the first port on the PIM. In the case there is two LEDs on the front, the first LED octet is the front and the second the back.
INT portState	1.3.6.1.4.1.208.39.3.2.1.4	INTEGER	read-only	This is a bit array which represent the state of the port. bit 0: Disabled due to configuration bit 1: Hardware error bit 2: No linkpulse bit 3: Disabled by manager bit 4: Disabled by access control bit 5: Disabled due to shared port
INT portCardNumber	1.3.6.1.4.1.208.39.3.2.1.5	INTEGER	read-only	The cardNumber in the switch system.
INT portPimNumber	1.3.6.1.4.1.208.39.3.2.1.6	INTEGER	read-only	The pimNumber in the switch system.
INT portPimPortNumber	1.3.6.1.4.1.208.39.3.2.1.7	INTEGER	read-only	The relative number of the port on the PIM.
portIfTable	1.3.6.1.4.1.208.39.3.3		not-accessible	Switch Interface Table.
portIfEntry	1.3.6.1.4.1.208.39.3.3.1		not-accessible	An entry containing object for a Switch interface.
INT portIfIndex	1.3.6.1.4.1.208.39.3.3.1.1	INTEGER	read-only	An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
STR portIfDescr	1.3.6.1.4.1.208.39.3.3.1.2	DisplayString	read-write	User configurable description of the port.
STR portIfLocation	1.3.6.1.4.1.208.39.3.3.1.3	DisplayString	read-write	User configurable location of the port.
INT portIfSwitchMode	1.3.6.1.4.1.208.39.3.3.1.4	INTEGER	read-write	Port Switch mode. If set to default(1) value from defaultSwitchMode is used.
INT portIfDuplex	1.3.6.1.4.1.208.39.3.3.1.5	INTEGER	read-only	Port Duplex mode. For ports in auto mode the mode may change automatically between autoDetect(1), autoDetectedHalf(3) and autoDetectedFull(5).
INT portIfThrottleBack	1.3.6.1.4.1.208.39.3.3.1.6	INTEGER	read-write	Port ThrottleBack mode. If set to default(1) value from defaultThrottleBackMode is used.
INT portIfType	1.3.6.1.4.1.208.39.3.3.1.7	INTEGER	read-only	The type of Physical interface at the port.
INT portIfDuplexSupported	1.3.6.1.4.1.208.39.3.3.1.8	INTEGER	read-only	The duplex mode supported for a port.
INT portIfSpeedSupported	1.3.6.1.4.1.208.39.3.3.1.9	INTEGER	read-only	The speed supported for a port.
OCT portIfSpeedAndDuplex	1.3.6.1.4.1.208.39.3.3.1.10	OCTET STRING	read-write	This object is used to configure the speed and duplex mode for a port. Byte 1: negotiation manual(0) autoDisable(1) autoAlternative(2) Byte 2: speed auto(1) 10(2) 100(3) 155(4) Byte 3: alternativeSpeed unused(0) (read-only) Byte 4: duplexMode auto(1) half(2) full(3) Byte 5: alternativeDuplexMode unused(0) (read-only) half(2) full(3) Explanation of the different negotiation: Manual: The port does not support auto detect of speed and duplex which means that only fixed values are legal. AutoDisable: The port supports auto negotiation and if the connected port does not except the suggested values the port will be disabled. AutoAlternative: The port supports auto negotiation and if the connected port does not except the suggested values the port will be set to some alternative values.
statistic	1.3.6.1.4.1.208.39.4
txStatTable	1.3.6.1.4.1.208.39.4.1		not-accessible	MIA ASIC Transmit statistic Table.
txStatEntry	1.3.6.1.4.1.208.39.4.1.1		not-accessible	An entry containing object for MIA ASIC Transmit statistic.
INT txStatIndex	1.3.6.1.4.1.208.39.4.1.1.1	INTEGER	read-only	An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
CTR txUCPkts64Octets	1.3.6.1.4.1.208.39.4.1.1.2	Counter	read-only	64 byte unicast packets transmitted
CTR txUCPkts65To127Octets	1.3.6.1.4.1.208.39.4.1.1.3	Counter	read-only	65 to 127 byte unicast packets transmitted
CTR txUCPkts128To255Octets	1.3.6.1.4.1.208.39.4.1.1.4	Counter	read-only	128 to 255 byte unicast packets transmitted
CTR txUCPkts256To511Octets	1.3.6.1.4.1.208.39.4.1.1.5	Counter	read-only	256 to 511 byte unicast packets transmitted
CTR txUCPkts512To1023Octets	1.3.6.1.4.1.208.39.4.1.1.6	Counter	read-only	512 to 1023 byte unicast packets transmitted
CTR txUCPkts1024To1518Octets	1.3.6.1.4.1.208.39.4.1.1.7	Counter	read-only	1024 to 1518 byte unicast packets transmitted
CTR txMCPkts64Octets	1.3.6.1.4.1.208.39.4.1.1.8	Counter	read-only	64 byte multicast packets transmitted
CTR txMCPkts65To127Octets	1.3.6.1.4.1.208.39.4.1.1.9	Counter	read-only	65 to 127 byte multicast packets transmitted
CTR txMCPkts128To255Octets	1.3.6.1.4.1.208.39.4.1.1.10	Counter	read-only	128 to 255 byte multicast packets transmitted
CTR txMCPkts256To511Octets	1.3.6.1.4.1.208.39.4.1.1.11	Counter	read-only	256 to 511 byte multicast packets transmitted
CTR txMCPkts512To1023Octets	1.3.6.1.4.1.208.39.4.1.1.12	Counter	read-only	512 to 1023 byte multicast packets transmitted
CTR txMCPkts1024To1518Octets	1.3.6.1.4.1.208.39.4.1.1.13	Counter	read-only	1024 to 1518 byte multicast packets transmitted
CTR txBCPkts64Octets	1.3.6.1.4.1.208.39.4.1.1.14	Counter	read-only	64 byte broadcast packets transmitted
CTR txBCPkts65To127Octets	1.3.6.1.4.1.208.39.4.1.1.15	Counter	read-only	65 to 127 byte broadcast packets transmitted
CTR txBCPkts128To255Octets	1.3.6.1.4.1.208.39.4.1.1.16	Counter	read-only	128 to 255 byte broadcast packets transmitted
CTR txBCPkts256To511Octets	1.3.6.1.4.1.208.39.4.1.1.17	Counter	read-only	256 to 511 byte broadcast packets transmitted
CTR txBCPkts512To1023Octets	1.3.6.1.4.1.208.39.4.1.1.18	Counter	read-only	512 to 1023 byte broadcast packets transmitted
CTR txBCPkts1024To1518Octets	1.3.6.1.4.1.208.39.4.1.1.19	Counter	read-only	1024 to 1518 byte broadcast packets transmitted
CTR txDeffereds	1.3.6.1.4.1.208.39.4.1.1.20	Counter	read-only	A transmission must await a silent net in Simplex mode. If the transmission is delayed due to a non silent net the transmission is deffered.
CTR txOctetsHis	1.3.6.1.4.1.208.39.4.1.1.21	Counter	read-only	High part of a 64 bit octet transmitted counter
CTR txOctetsLos	1.3.6.1.4.1.208.39.4.1.1.22	Counter	read-only	Low part of a 64 bit octet transmitted counter
CTR txExcessiveDefferalsErrors	1.3.6.1.4.1.208.39.4.1.1.23	Counter	read-only	Maximum defferal should be the duration of a maximum length packet, if no errors on the net. Excessive defferal is indicated if defferal duration is more than approximately 2 maximum packets.
CTR txForwardedRxError	1.3.6.1.4.1.208.39.4.1.1.24	Counter	read-only	The transmission are aborted on the transmitting port of the switch if the receiving port of the present packet receives are packet with error or receives a collision fragment. This should never occur in Store and forward mode, while collisions never should provoke this event in fragment free mode, except for at late collisions on the receiving net.
CTR txNiaUnderRunDrops	1.3.6.1.4.1.208.39.4.1.1.25	Counter	read-only	The NIA TX buffer gets in underrun if the nimbus is overloaded. This should only happen if a configuration is made which loads the Nimbus with more than a load equal to 44 simplex 10Mbit net. NOTE: This only counts for NIA100 interfaces.
CTR txLinkDownEvents	1.3.6.1.4.1.208.39.4.1.1.26	Counter	read-only	No link pulses are received. Usually this means that the cable are removed.
OCT txAllCounterPackets	1.3.6.1.4.1.208.39.4.1.1.27	OCTET STRING	read-only	A collection of all counters for byte and packet counters. This object is needed to optimise SNMP traffic. The counters in this string are txStatIndex INTEGER txOctetsHis Counter txOctetsLos Counter txUCPkts64Octets Counter txUCPkts65To127Octets Counter txUCPkts128To255Octets Counter txUCPkts256To511Octets Counter txUCPkts512To1023Octets Counter txUCPkts1024To1518Octets Counter txMCPkts64Octets Counter txMCPkts65To127Octets Counter txMCPkts128To255Octets Counter txMCPkts256To511Octets Counter txMCPkts512To1023Octets Counter txMCPkts1024To1518Octets Counter txBCPkts64Octets Counter txBCPkts65To127Octets Counter txBCPkts128To255Octets Counter txBCPkts256To511Octets Counter txBCPkts512To1023Octets Counter txBCPkts1024To1518Octets Counter The values are represented in the OCTET STRING in the listed order, each value stored as a 32 bits big engine value.
OCT txAllCounterOthers	1.3.6.1.4.1.208.39.4.1.1.28	OCTET STRING	read-only	A collection of all counters other than for byte and packet counters. This object is needed to optimise SNMP traffic. The counters in this string are txStatIndex INTEGER txDeffereds Counter txExcessiveDefferalsErrors Counter txForwardedRxError Counter txNiaUnderRunDrops Counter txLinkDownEvents Counter -- Counters from RFC1643 txCSenseErrors Counter txSQEErrors Counter txLateCollisions Counter txExcessiveCollisionErrors Counter txSingleCollisionFrames Counter txMultipleCollisionFrames Counter The values are represented in the OCTET STRING in the listed order, each value stored as a 32 bits big engine value.
rxStatTable	1.3.6.1.4.1.208.39.4.2		not-accessible	MIA ASIC Receive statistic Table.
rxStatEntry	1.3.6.1.4.1.208.39.4.2.1		not-accessible	An entry containing object for MIA ASIC Receive statistic.
INT rxStatIndex	1.3.6.1.4.1.208.39.4.2.1.1	INTEGER	read-only	An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
CTR rxUCPkts64OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.2	Counter	read-only	64 byte unicast packets received which has not been forwarded
CTR rxUCPkts64OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.3	Counter	read-only	64 byte unicast packets received which has been forwarded
CTR rxUCPkts65To127OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.4	Counter	read-only	65 to 127 byte unicast packets received which has not been forwarded
CTR rxUCPkts65To127OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.5	Counter	read-only	65 to 127 byte unicast packets received which has been forwarded
CTR rxUCPkts128To255OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.6	Counter	read-only	128 to 255 byte unicast packets received which has not been forwarded
CTR rxUCPkts128To255OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.7	Counter	read-only	128 to 255 byte unicast packets received which has been forwarded
CTR rxUCPkts256To511OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.8	Counter	read-only	256 to 511 byte unicast packets received which has not been forwarded
CTR rxUCPkts256To511OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.9	Counter	read-only	255 to 511 byte unicast packets received which has been forwarded
CTR rxUCPkts512To1023OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.10	Counter	read-only	512 to 1023 byte unicast packets received which has not been forwarded
CTR rxUCPkts512To1023OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.11	Counter	read-only	512 to 1023 byte unicast packets received which has been forwarded
CTR rxUCPkts1024To1518OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.12	Counter	read-only	1024 to 1518 byte unicast packets received which has not been forwarded
CTR rxUCPkts1024To1518OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.13	Counter	read-only	1024 to 1518 byte unicast packets received which has been forwarded
CTR rxShortErrors	1.3.6.1.4.1.208.39.4.2.1.14	Counter	read-only	Receive fragments shorter than minimum ordinary collision fragment.
CTR rxRuntErrors	1.3.6.1.4.1.208.39.4.2.1.15	Counter	read-only	Ordinary collision fragments received.
CTR rxDataRateMMErrors	1.3.6.1.4.1.208.39.4.2.1.16	Counter	read-only	Data Rate Miss Match Error occurs if the data rate deviation is larger than allowed. This should only occur if problems with the TX oscillator in the adapter transmitting the frame.
CTR rxMCPkts64OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.17	Counter	read-only	64 byte multicast packets received which has not been forwarded
CTR rxMCPkts64OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.18	Counter	read-only	64 byte multicast packets received which has been forwarded
CTR rxMCPkts65To127OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.19	Counter	read-only	65 to 127 byte multicast packets received which has not been forwarded
CTR rxMCPkts65To127OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.20	Counter	read-only	65 to 127 byte multicast packets received which has been forwarded
CTR rxMCPkts128To255OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.21	Counter	read-only	128 to 255 byte multicast packets received which has not been forwarded
CTR rxMCPkts128To255OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.22	Counter	read-only	128 to 255 byte multicast packets received which has been forwarded
CTR rxMCPkts256To511OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.23	Counter	read-only	256 to 511 byte multicast packets received which has not been forwarded
CTR rxMCPkts256To511OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.24	Counter	read-only	256 to 511 byte multicast packets received which has been forwarded
CTR rxMCPkts512To1023OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.25	Counter	read-only	512 to 1023 byte multicast packets received which has not been forwarded
CTR rxMCPkts512To1023OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.26	Counter	read-only	512 to 1023 byte multicast packets received which has been forwarded
CTR rxMCPkts1024To1518OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.27	Counter	read-only	1024 to 1518 byte multicast packets received which has not been forwarded
CTR rxMCPkts1024To1518OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.28	Counter	read-only	1024 to 1518 byte multicast packets received which has been forwarded
CTR rxOctetsLocalHis	1.3.6.1.4.1.208.39.4.2.1.29	Counter	read-only	High part of a 64 bit octet received counter which has not been forwarded
CTR rxOctetsLocalLos	1.3.6.1.4.1.208.39.4.2.1.30	Counter	read-only	Low part of a 64 bit octet received counter which has not been forwarded
CTR rxOctetsForwardedHis	1.3.6.1.4.1.208.39.4.2.1.31	Counter	read-only	High part of a 64 bit octet received counter which has been forwarded
CTR rxOctetsForwardedLos	1.3.6.1.4.1.208.39.4.2.1.32	Counter	read-only	Low part of a 64 bit octet received counter which has been forwarded
CTR rxBCPkts64OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.33	Counter	read-only	64 byte broadcast packets received which has not been forwarded
CTR rxBCPkts64OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.34	Counter	read-only	64 byte broadcast packets received which has been forwarded
CTR rxBCPkts65To127OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.35	Counter	read-only	65 to 127 byte broadcast packets received which has not been forwarded
CTR rxBCPkts65To127OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.36	Counter	read-only	65 to 127 byte broadcast packets received which has been forwarded
CTR rxBCPkts128To255OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.37	Counter	read-only	128 to 255 byte broadcast packets received which has not been forwarded
CTR rxBCPkts128To255OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.38	Counter	read-only	128 to 255 byte broadcast packets received which has been forwarded
CTR rxBCPkts256To511OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.39	Counter	read-only	256 to 511 byte broadcast packets received which has not been forwarded
CTR rxBCPkts256To511OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.40	Counter	read-only	256 to 511 byte broadcast packets received which has been forwarded
CTR rxBCPkts512To1023OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.41	Counter	read-only	512 to 1023 byte broadcast packets received which has not been forwarded
CTR rxBCPkts512To1023OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.42	Counter	read-only	512 to 1023 byte broadcast packets received which has been forwarded
CTR rxBCPkts1024To1518OctetsLocals	1.3.6.1.4.1.208.39.4.2.1.43	Counter	read-only	1024 to 1518 byte broadcast packets received which has not been forwarded
CTR rxBCPkts1024To1518OctetsForwardeds	1.3.6.1.4.1.208.39.4.2.1.44	Counter	read-only	1024 to 1518 byte broadcast packets received which has been forwarded
CTR rxFilterMACUnexp2ndPortDrops	1.3.6.1.4.1.208.39.4.2.1.45	Counter	read-only	MAC address has been moved from one port to another
CTR rxFilterIllegalMACDrops	1.3.6.1.4.1.208.39.4.2.1.46	Counter	read-only	Indicate more than one MAC address on a port which is not a network port or in general that the filter discards a packet due to an illegal source MAC address
CTR rxFlowCtrlCollCounter	1.3.6.1.4.1.208.39.4.2.1.47	Counter	read-only	This counter counts the number of Flow Control collisions, which are generated due to flow control. Flow control are used when most of the pool memory are used to limit further amount of RX data until memory available.
CTR rxVeryLongErrors	1.3.6.1.4.1.208.39.4.2.1.48	Counter	read-only	Occurs only if frame longer than 6000 bytes are received.
CTR rxLongErrors	1.3.6.1.4.1.208.39.4.2.1.49	Counter	read-only	Occurs if a frame longer than 1518 bytes and shorter than 6000 bytes are received.
CTR rxPiaOutOfPoolsDrop	1.3.6.1.4.1.208.39.4.2.1.50	Counter	read-only	Reception is aborted due to lack of Pool memory. The switch is overloaded.
CTR rxManchesterCodeViolationErrors	1.3.6.1.4.1.208.39.4.2.1.51	Counter	read-only	An illegal symbol received on a 100Base-X port.
CTR rxRxJabbers	1.3.6.1.4.1.208.39.4.2.1.52	Counter	read-only	Jabber is counted instead of a long error if the frame contains dribble bits or FCS error.
CTR rxNiaOverRunDrops	1.3.6.1.4.1.208.39.4.2.1.53	Counter	read-only	The NIA RX buffer gets in overrun if the nimbus is overloaded. This should only happen if a configuration is made which loads the Nimbus with more than a load equal to 44 simplex 10Mbit net.
OCT rxAllCounterPackets	1.3.6.1.4.1.208.39.4.2.1.54	OCTET STRING	read-only	A collection of all counters for byte and packet counters. This object is needed to optimise SNMP traffic. The counters in this string are rxStatIndex INTEGER rxOctetsLocalHis Counter rxOctetsLocalLos Counter rxOctetsForwardedHis Counter rxOctetsForwardedLos Counter rxUCPkts64OctetsLocals Counter rxUCPkts64OctetsForwardeds Counter rxUCPkts65To127OctetsLocals Counter rxUCPkts65To127OctetsForwardeds Counter rxUCPkts128To255OctetsLocals Counter rxUCPkts128To255OctetsForwardeds Counter rxUCPkts256To511OctetsLocals Counter rxUCPkts256To511OctetsForwardeds Counter rxUCPkts512To1023OctetsLocals Counter rxUCPkts512To1023OctetsForwardeds Counter rxUCPkts1024To1518OctetsLocals Counter rxUCPkts1024To1518OctetsForwardeds Counter rxMCPkts64OctetsLocals Counter rxMCPkts64OctetsForwardeds Counter rxMCPkts65To127OctetsLocals Counter rxMCPkts65To127OctetsForwardeds Counter rxMCPkts128To255OctetsLocals Counter rxMCPkts128To255OctetsForwardeds Counter rxMCPkts256To511OctetsLocals Counter rxMCPkts256To511OctetsForwardeds Counter rxMCPkts512To1023OctetsLocals Counter rxMCPkts512To1023OctetsForwardeds Counter rxMCPkts1024To1518OctetsLocals Counter rxMCPkts1024To1518OctetsForwardeds Counter rxBCPkts64OctetsLocals Counter rxBCPkts64OctetsForwardeds Counter rxBCPkts65To127OctetsLocals Counter rxBCPkts65To127OctetsForwardeds Counter rxBCPkts128To255OctetsLocals Counter rxBCPkts128To255OctetsForwardeds Counter rxBCPkts256To511OctetsLocals Counter rxBCPkts256To511OctetsForwardeds Counter rxBCPkts512To1023OctetsLocals Counter rxBCPkts512To1023OctetsForwardeds Counter rxBCPkts1024To1518OctetsLocals Counter rxBCPkts1024To1518OctetsForwardeds Counter The values are represented in the OCTET STRING in the listed order, each value stored as a 32 bits big engine value.
OCT rxAllCounterOthers	1.3.6.1.4.1.208.39.4.2.1.55	OCTET STRING	read-only	A collection of all counters other than for byte and packet counters. This object is needed to optimise SNMP traffic. The counters in this string are rxStatIndex INTEGER rxShortErrors Counter rxRuntErrors Counter rxDataRateMMErrors Counter rxFilterMACUnexp2ndPortDrops Counter rxFilterIllegalMACDrops Counter rxFlowCtrlCollCounter Counter rxVeryLongErrors Counter rxLongErrors Counter rxPiaOutOfPoolsDrop Counter rxManchesterCodeViolationErrors Counter rxRxJabbers Counter rxNiaOverRunDrops Counter -- Counters from RFC1643 rxAlignErrors Counter rxFCSErrors Counter The values are represented in the OCTET STRING in the listed order, each value stored as a 32 bits big engine value.
OCT totalRxTxPackets	1.3.6.1.4.1.208.39.4.3	OCTET STRING	read-only	This object is used for LED control to display traffic. Values in the string are all packets transmitted and received at each port. The number and order of values equals the ifIndex. Each entry is 4 bytes. The first 4 bytes of the string is the value of portLastChange.
OCT totalCollisions	1.3.6.1.4.1.208.39.4.4	OCTET STRING	read-only	This object is used for LED control to display collision. Values in the string are the total collisions at each port. The number and order of values equals the ifIndex. Each entry is 4 bytes. The first 4 bytes of the string is the value of portLastChange.
adaptiveForwardMode	1.3.6.1.4.1.208.39.5
INT adaptiveForwardModeSampleTime	1.3.6.1.4.1.208.39.5.1	INTEGER	read-write	Specify how long (sec) the received packets will be monitored. The resulting forwarding mode will be based on the quality of the packets
INT adaptiveForwardModeRuntsOffset	1.3.6.1.4.1.208.39.5.2	INTEGER	read-write	Specifies the minimum amount of runts during the sample time which forces the port out of cutThrough(2). The value is specified in per mille * 1000
INT adaptiveForwardModeRuntsRange	1.3.6.1.4.1.208.39.5.3	INTEGER	read-write	Specifies together with adaptiveForwardModeRuntsOffset the maximum amount of runts allowed during the sample time, which forces the port back to cutThrough(2). The value is specified in per mille * 1000
INT adaptiveForwardModeCrcsOffset	1.3.6.1.4.1.208.39.5.4	INTEGER	read-write	Specifies the maximum amount of crc errors during the sample time which forces the port out of Store and Forward. The value is specified in per mille * 1000
INT adaptiveForwardModeCrcsRange	1.3.6.1.4.1.208.39.5.5	INTEGER	read-write	Specifies together with adaptiveForwardModeCrcsOffset the maximum amount of crc errors during the sample time which forces the port out of Store and Forward. The value is specified in per mille * 1000
chipSets	1.3.6.1.4.1.208.39.6
chipSetNIA10	1.3.6.1.4.1.208.39.6.1
chipSetNIA100	1.3.6.1.4.1.208.39.6.2
cards	1.3.6.1.4.1.208.39.7
cardTable	1.3.6.1.4.1.208.39.7.1		not-accessible	This table describes which cards a switch system consist of and how they are connected.
cardEntry	1.3.6.1.4.1.208.39.7.1.1		not-accessible	An entry contains either a card or an expansion card and how many PIMs it contains.
INT cardNumber	1.3.6.1.4.1.208.39.7.1.1.1	INTEGER	read-only	The card index number.
PRO cardId	1.3.6.1.4.1.208.39.7.1.1.2	ProductIds	read-only	The produce identification the card.
INT cardFirstPort	1.3.6.1.4.1.208.39.7.1.1.3	INTEGER	read-only	The portNumber of the first port on the card.
INT cardMaxPims	1.3.6.1.4.1.208.39.7.1.1.4	INTEGER	read-only	The maximum number of PIMs this card can contain.
pimTable	1.3.6.1.4.1.208.39.7.2		not-accessible	This table describes the PIMs inserted in the switch system.
pimEntry	1.3.6.1.4.1.208.39.7.2.1		not-accessible	An entry describes the PIM.
INT pimCardNumber	1.3.6.1.4.1.208.39.7.2.1.1	INTEGER	read-only	The card number in the cardTable that this PIM is inserted in.
INT pimNumber	1.3.6.1.4.1.208.39.7.2.1.2	INTEGER	read-only	The number of the PIM.
PRO pimId	1.3.6.1.4.1.208.39.7.2.1.3	ProductIds	read-only	The product identification of the PIM.
INT pimFirstPort	1.3.6.1.4.1.208.39.7.2.1.4	INTEGER	read-only	The portNumber of the first port on the PIM.
INT pimNumberOfPorts	1.3.6.1.4.1.208.39.7.2.1.5	INTEGER	read-only	The number of ports on the PIM.

RFC description

Intel Ethernet switch management MIB covering switching parameters, module configuration, ports, and performance statistics.

Start monitoring Ethernet switch with port/VLAN management (vendor not confirmed) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ETH-SWITCH-MIB

What Is ETH-SWITCH-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description