SCANET-MIB

All MIBs › SCANET-MIB

Category: Generic Switch Management

Description: Manages SCANET network device configuration, interface status, and operational monitoring.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SCANET-MIB?

SCANET-MIB is described as managing SCANET network device configuration, interface status, and general operational monitoring, though no module description or sample object list was available for this module to confirm specifics. Based on its stated purpose, it likely exposes device configuration parameters and interface-level operational status typical of a vendor-specific network device MIB. Without sample objects to ground specific hardware/software status claims (uptime, temperature, CPU/memory), no detailed monitoring capabilities can be honestly asserted beyond the general interface-status and configuration focus indicated by its short description. It likely depends on standard MIB-II (IF-MIB) conventions for interface representation, as is typical for vendor device MIBs of this kind. It would be deployed wherever SCANET-branded network equipment is managed via SNMP. Loading SCANET-MIB into a MIB Browser would be a practical first step for an administrator to enumerate its actual configuration and interface-status objects, since published documentation for it is otherwise sparse.

IPNetwork Monitor allows you to monitor SNMP objects defined in SCANET-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

SCANET network devices

Monitoring Examples

No sample_objects were provided for this MIB, so no concrete object-level monitoring scenario can be honestly described; the module_desc field was also empty. Administrators would need to consult the actual MIB source to identify specific tables and objects available for configuration and interface status polling.

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress
TimeTicks
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
autAccessEntry	1.3.6.1.4.1.208.2.1.7.1		not-accessible	Authorization accept entry.
IP autAccessIP	1.3.6.1.4.1.208.2.1.7.1.1	IpAddress	read-only	IP address of the host that has successfully passed the authorization.
autAccessTable	1.3.6.1.4.1.208.2.1.7		not-accessible	Authorization Access list. A list of all IP addresses that has passed the authorization. The access can be from either SNMP, TFTP or Telnet
TIK autAccessTime	1.3.6.1.4.1.208.2.1.7.1.2	TimeTicks	read-only	Time of last successfully access.
INT autDelete	1.3.6.1.4.1.208.2.11.6.1.3	INTEGER	read-write	The autEntry is removed when set to 1. Allways returns 0
autEntry	1.3.6.1.4.1.208.2.11.6.1		not-accessible	Authorization entry.
OCT autIpAndAccessAndCommunity	1.3.6.1.4.1.208.2.11.6.1.2	OCTET STRING	read-write	This object contains the Ip address (4 byte), Access (1 byte) and Community (0 to 31 byte). If the Ip address is zero then any ip address is allowed. The Access can take the values readOnly(1) and readWrite(2). If the community string is zero length, then any value of community is allowed.
INT autMaxEntries	1.3.6.1.4.1.208.2.11.5	INTEGER	read-only	Maximun number of entries in the autTable
INT autNumber	1.3.6.1.4.1.208.2.11.6.1.1	INTEGER	read-only	A number that uniquely identifies an authorization entry.
autTable	1.3.6.1.4.1.208.2.11.6		not-accessible	Authorization list.
INT brdNumber	1.3.6.1.4.1.208.2.1.3.1.1	INTEGER	read-only	An index identifying one or more boards.
STR cause	1.3.6.1.4.1.208.2.11.3	DisplayString	read-only	A general object used for SNMP-TRAPS. Notice that this object for newer products is obsolete and replaced by unique TRAP's.
INT configurationLastChanged	1.3.6.1.4.1.208.2.1.9	INTEGER	read-only	Time Of Day the configuration was last changed. The time is expresed in seconds since midnight (0 hour), Januar 1, 1970.
INT configurationLastSaved	1.3.6.1.4.1.208.2.1.10	INTEGER	read-only	Time Of Day the configuration was saved to FLASH. The time is expresed in seconds since midnight (0 hour), Januar 1, 1970.
cs_14xx	1.3.6.1.4.1.208.1.32
cs_21xx	1.3.6.1.4.1.208.1.68
cs_3300	1.3.6.1.4.1.208.1.42
cs_72xx	1.3.6.1.4.1.208.1.13
cs_76xx	1.3.6.1.4.1.208.1.15
ct_30xx	1.3.6.1.4.1.208.1.69
ct_40xx	1.3.6.1.4.1.208.1.83
er9100	1.3.6.1.4.1.208.1.88.25
er9200	1.3.6.1.4.1.208.1.88.26
er9300	1.3.6.1.4.1.208.1.88.27
er9400	1.3.6.1.4.1.208.1.88.28
INT errorLogNumber	1.3.6.1.4.1.208.2.1.5	INTEGER	read-write	Number of entries in the error log. Setting the value zero will clear the log. Set of any other value is invalid.
es_1520	1.3.6.1.4.1.208.1.35.5
es_1810	1.3.6.1.4.1.208.1.35.1
es_1820	1.3.6.1.4.1.208.1.35.2
es_1850	1.3.6.1.4.1.208.1.35.6
es_1851	1.3.6.1.4.1.208.1.35.7
es100fx	1.3.6.1.4.1.208.1.35.8
es10t24	1.3.6.1.4.1.208.1.35.3
es10t24plus	1.3.6.1.4.1.208.1.35.4
ethernetSwitch	1.3.6.1.4.1.208.1.35
INT filter	1.3.6.1.4.1.208.2.11.1	INTEGER	read-write	Filter to control logging af events.
STR fwId	1.3.6.1.4.1.208.2.1.3.1.3	DisplayString	read-only	F/W identification for the board. ex PROM version number.
STR hwId	1.3.6.1.4.1.208.2.1.3.1.2	DisplayString	read-only	H/W identification for the board, ex 10T24.
idEntry	1.3.6.1.4.1.208.2.1.3.1		not-accessible	A H/W and F/W information entry for each set of boards.
idTable	1.3.6.1.4.1.208.2.1.3		not-accessible	A table containing H/W and F/W identification.
in_40xx	1.3.6.1.4.1.208.1.82
ip	1.3.6.1.4.1.208.2.4
OCT ipAddrAndMask	1.3.6.1.4.1.208.2.4.1.1.2	OCTET STRING	read-write	The IP Address and the Subnet Mask. The format of the octet string is: 4 bytes : IP Address 4 bytes : IP Subnet Mask.
ipEntry	1.3.6.1.4.1.208.2.4.1.1		not-accessible	Entry with an IP address and an IP mask.
INT ipIndex	1.3.6.1.4.1.208.2.4.1.1.1	INTEGER	read-only	The value of an interface indentified by ifIndex.
ipTable	1.3.6.1.4.1.208.2.4.1		not-accessible	This table is needed to set the IP address and the IP mask. Refer to the table ipAddrTable in MIB-II, for a description.
matchboxRouter	1.3.6.1.4.1.208.1.88
mfts	1.3.6.1.4.1.208.1.67
mib2ext	1.3.6.1.4.1.208.2
mr_1010	1.3.6.1.4.1.208.1.88.1
mr_1011	1.3.6.1.4.1.208.1.88.2
mr_1013	1.3.6.1.4.1.208.1.88.3
mr_1014	1.3.6.1.4.1.208.1.88.4
mr_1020	1.3.6.1.4.1.208.1.88.15
mr_1021	1.3.6.1.4.1.208.1.88.23
mr_1023	1.3.6.1.4.1.208.1.88.17
mr_1024	1.3.6.1.4.1.208.1.88.19
mr_1040	1.3.6.1.4.1.208.1.88.21
mr_1050	1.3.6.1.4.1.208.1.88.5
mr_1051	1.3.6.1.4.1.208.1.88.6
mr_1055	1.3.6.1.4.1.208.1.88.13
mr_1110	1.3.6.1.4.1.208.1.88.7
mr_1111	1.3.6.1.4.1.208.1.88.8
mr_1113	1.3.6.1.4.1.208.1.88.9
mr_1114	1.3.6.1.4.1.208.1.88.10
mr_1120	1.3.6.1.4.1.208.1.88.16
mr_1121	1.3.6.1.4.1.208.1.88.24
mr_1123	1.3.6.1.4.1.208.1.88.18
mr_1124	1.3.6.1.4.1.208.1.88.20
mr_1140	1.3.6.1.4.1.208.1.88.22
mr_1150	1.3.6.1.4.1.208.1.88.11
mr_1151	1.3.6.1.4.1.208.1.88.12
mr_1155	1.3.6.1.4.1.208.1.88.14
STR print	1.3.6.1.4.1.208.2.11.2	DisplayString	read-only	A general object used for SNMP-TRAPS. Notice that this object for newer products is obsolete and replaced by unique TRAP's.
products	1.3.6.1.4.1.208.1
INT pysmiFakeCol988	1.3.6.1.4.1.208.2.1.7.1.4294967295	INTEGER	not-accessible
IP pysmiFakeCol989	1.3.6.1.4.1.208.2.4.1.1.4294967295	IpAddress	not-accessible
INT pysmiFakeCol990	1.3.6.1.4.1.208.2.40.1.1.4294967295	INTEGER	not-accessible
INT ram	1.3.6.1.4.1.208.2.1.2	INTEGER	read-only	The size of the CPU RAM.
INT reboot	1.3.6.1.4.1.208.2.1.1	INTEGER	read-write	Object to control actions in the device such as: resetNow(1) is reset the device immediately, reloadParm(7) is reload parameterblock from FLASH. saveParm(8) is save the parameter block to FLASH. Notice that not all products supports all values of this object.
scanet	1.3.6.1.4.1.208
scaProt	1.3.6.1.4.1.208.4
snmp	1.3.6.1.4.1.208.2.11
STR solution	1.3.6.1.4.1.208.2.11.4	DisplayString	read-only	A general object used for SNMP-TRAPS. Notice that this object for newer products is obsolete and replaced by unique TRAP's.
swEntry	1.3.6.1.4.1.208.2.1.4.1		not-accessible	A filename.
swInfoEntry	1.3.6.1.4.1.208.2.40.1.1		not-accessible	Software information entry.
swInfoTable	1.3.6.1.4.1.208.2.40.1		not-accessible	Software information table. If the product has a dual software system the table contains two entries.
TIK swLoadTime	1.3.6.1.4.1.208.2.40.1.1.3	TimeTicks	read-only	The time the software was loaded and saved to FLASH.
STR swName	1.3.6.1.4.1.208.2.1.4.1.1	DisplayString	read-only	Filename of S/W.
OCT swName2	1.3.6.1.4.1.208.2.40.1.1.2	OCTET STRING	read-only	The software file name (0 to 46 bytes)
INT swStatus	1.3.6.1.4.1.208.2.40.1.1.1	INTEGER	read-write	This object is only used for products with a dual software system. After loading and initiating new software the status is experimental. The software must be approved to be used after power off.
swTable	1.3.6.1.4.1.208.2.1.4		not-accessible	A table af S/W filenames.
IP swTftpIp	1.3.6.1.4.1.208.2.40.1.1.4	IpAddress	read-only	IP address of the TFTP server from which the software was loaded.
OCT swTftpIpAndSwName	1.3.6.1.4.1.208.2.40.2	OCTET STRING	read-write	This object contains the IP address of the TFTP server (4 bytes) and the software file name (0 to 46 bytes). This is used to initiate a software update.
swUpdate	1.3.6.1.4.1.208.2.40
INT swUpdateResult	1.3.6.1.4.1.208.2.40.3	INTEGER	read-only	The result of software update.
system	1.3.6.1.4.1.208.2.1
INT systemLogNumber	1.3.6.1.4.1.208.2.1.6	INTEGER	read-write	Number of entries in the system log. Setting the value zero will clear the log. Set of any other value is invalid.
INT timeOfDay	1.3.6.1.4.1.208.2.1.8	INTEGER	read-write	The system's Time Of Day. The time is expresed in seconds since midnight (0 hour), Januar 1, 1970.
INT trapDelete	1.3.6.1.4.1.208.2.11.8.1.3	INTEGER	read-write	The trapEntry is removed when set to 1. Allways returns 0
trapEntry	1.3.6.1.4.1.208.2.11.8.1		not-accessible	Host Trap entry.
OCT trapIpAndCommunity	1.3.6.1.4.1.208.2.11.8.1.2	OCTET STRING	read-write	This object contains the Ip address (4 byte) and the Community (0 to 31 byte) used in the Traps.
INT trapMaxEntries	1.3.6.1.4.1.208.2.11.7	INTEGER	read-only	Maximun number of entries in the trapTable
INT trapNumber	1.3.6.1.4.1.208.2.11.8.1.1	INTEGER	read-only	A number that uniquely identifies an trap entry.
trapTable	1.3.6.1.4.1.208.2.11.8		not-accessible	Host Trap list.
ts_2104	1.3.6.1.4.1.208.1.12
INT unsavedConfiguration	1.3.6.1.4.1.208.2.1.11	INTEGER	read-only	Indicates if there are unsaved configuration changes to FLASH. If the value is yes(2) the configuration has been changed and can be saved by setting the object reboot to saveParm(8).

FAQ

What would SCANET-MIB let me check on a SCANET network device?
Based on its stated purpose, it covers device configuration parameters and interface-level operational status, typical of a vendor-specific network device MIB. An administrator managing SCANET equipment would use it as a general interface-status and configuration check, though published documentation for this module is sparse enough that specific object names can't be confirmed beyond that general scope.

Why would loading SCANET-MIB into a MIB browser be a useful first step before monitoring a SCANET device?
Since detailed object-level documentation for SCANET-MIB is limited, compiling it into a MIB browser lets an administrator directly enumerate its actual configuration and interface-status objects. It's also expected to build on standard MIB-II/IF-MIB conventions for representing interfaces, as is typical for vendor device MIBs of this kind.

RFC description

Scanner network management MIB for document imaging device monitoring.

Start monitoring SCANET network devices (configuration/interface status, vendor origin uncertain) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SCANET-MIB

What Is SCANET-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

FAQ

RFC description