All MIBs › EQL-DCB-MIB
Organization: EqualLogic Inc.
Last Updated: 2014-03-12
Category: Domain: Storage, Vendor: Dell/DNOS, Vendor: EqualLogic/Dell
Description: Dell EqualLogic Data Center Bridging (DCB) MIB (IEEE 802.1Qaz/Qbb/Qau) for lossless Ethernet in iSCSI storage networks.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is EQL-DCB-MIB?
This is Dell EqualLogic's implementation of the IEEE 802.1Qaz/802.1Qbb/802.1Qau Data Center Bridging (DCB) MIB, providing lossless-Ethernet configuration and status for iSCSI SAN storage arrays that rely on DCB (Priority Flow Control, Enhanced Transmission Selection, Congestion Notification) to guarantee storage traffic delivery. It exposes per-interface DCB capability/static configuration plus DCBX (DCB Exchange protocol) negotiation settings for traffic-class groups, ETS bandwidth allocation, PFC, application priority, and QCN. Its monitoring focus is network/software configuration status rather than device health per se: confirming whether DCBX negotiation for PFC and ETS is enabled and which traffic-class bandwidth allocations are active is essential to verifying that iSCSI traffic is protected from packet loss on a converged Ethernet fabric. It explicitly implements and depends on the IEEE 802.1Qaz standard DCB MIB definitions (clause 17.7). It is deployed on Dell EqualLogic storage array network interfaces connected to converged/lossless Ethernet fabrics in data centers. Engineers can download the EQL-DCB-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in EQL-DCB-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Dell EqualLogic iSCSI storage array
Monitoring Examples
A storage administrator would check eqlDcbxConfigPFCTxEnable and eqlDcbxConfigETSConfigurationTxEnable to confirm Priority Flow Control and ETS negotiation are enabled on a given interface, then inspect eqlDcbxAdminETSConTrafficClassGroupBandwidthTable to verify iSCSI traffic has been allocated sufficient bandwidth share relative to other traffic classes. eqlDcbStaticIfTable/eqlDcbStaticIfEntry would be reviewed to confirm the static per-interface DCB configuration matches the intended converged-network design, helping diagnose iSCSI latency or drops caused by DCB misconfiguration.
What Can Be Monitored
- DCBX PFC negotiation enable status
- DCBX ETS negotiation enable status
- traffic class group bandwidth allocation
- application priority negotiation status
- QCN negotiation status
- static per-interface DCB configuration
This MIB depends on
Related MIBs
Imported Objects
From EQLGROUP-MIB
| eqlGroupId | OBJECT-TYPE |
From EQLMEMBER-MIB
| eqlMemberIndex | OBJECT-TYPE |
From EQUALLOGIC-SMI
| equalLogic | MODULE-IDENTITY |
From RFC1213-MIB
| ifIndex |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 | |
| enterprises |
From SNMPv2-TC
| TimeInterval | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using eqlDcbPfcRequestsSent OID:
Select a Dell EqualLogic PS-series iSCSI SAN storage array (Data Center Bridging/DCBX) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type eqlDcbPfcRequestsSent into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports a count of the invoked PFC M_CONTROL.request primitives. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| eqlDcbMib | 1.3.6.1.4.1.12740.19 | Data Center Bridging MIB module. Copyright (c) 2010-2011 by Dell, Inc. All rights reserved. This software may not be copied, disclosed, transferred, or used except in accordance with a license granted by Dell, Inc. This software embodies proprietary information and trade secrets of Dell, Inc. Copyright (C) IEEE (2009). This version of this MIB module is published as clause 17.7 of IEEE Std 802.1Qaz; see the standard itself for full legal notices. | ||
| eqlDcbMIBObjects | 1.3.6.1.4.1.12740.19.1 | |||
| eqlDcbStaticIfTable | 1.3.6.1.4.1.12740.19.1.1 | not-accessible | EqualLogic-Persistent A table of DCB information per each interface of a system. Each row in this table supplies values for one port's DCB parameters. | |
| eqlDcbStaticIfEntry | 1.3.6.1.4.1.12740.19.1.1.1 | not-accessible | An entry in the DCB table, containing information about DCB on a single interface. | |
| T/F eqlDcbxConfigTCSupportedTxEnable | 1.3.6.1.4.1.12740.19.1.1.1.1 | TruthValue | read-write | This field is deprecated. |
| T/F eqlDcbxConfigETSConfigurationTxEnable | 1.3.6.1.4.1.12740.19.1.1.1.2 | TruthValue | read-write | The eqlDcbxConfigETSConfigurationTxEnable, which is defined as a truth value and configured by the network management, determines whether the IEEE 802.1 organizationally defined ETS Configuration TLV transmission is allowed on a given LLDP transmission capable port. The value of this object is restored from non-volatile storage after a re-initialization of the management system. |
| T/F eqlDcbxConfigETSRecommendationTxEnable | 1.3.6.1.4.1.12740.19.1.1.1.3 | TruthValue | read-write | The eqlDcbxConfigETSRecommendationTxEnable, which is defined as a truth value and configured by the network management, determines whether the IEEE 802.1 organizationally defined ETS Recommendation TLV transmission is allowed on a given LLDP transmission capable port. The value of this object is restored from non-volatile storage after a re-initialization of the management system. |
| T/F eqlDcbxConfigPFCTxEnable | 1.3.6.1.4.1.12740.19.1.1.1.4 | TruthValue | read-write | The eqlDcbxConfigPFCTxEnable, which is defined as a truth value and configured by the network management, determines whether the IEEE 802.1 organizationally defined Priority-based Flow Fontrol TLV transmission is allowed on a given LLDP transmission capable port. The value of this object is restored from non-volatile storage after a re-initialization of the management system. |
| T/F eqlDcbxConfigAppPriorityTxEnable | 1.3.6.1.4.1.12740.19.1.1.1.5 | TruthValue | read-write | The eqlDcbxConfigAppPriorityTxEnable, which is defined as a truth value and configured by the network management, determines whether the IEEE 802.1 organizationally defined Application Priority TLV transmission is allowed on a given LLDP transmission capable port. The value of this object is restored from non-volatile storage after a re-initialization of the management system. |
| T/F eqlDcbxConfigQcnTxEnable | 1.3.6.1.4.1.12740.19.1.1.1.6 | TruthValue | read-write | The eqlDcbxConfigQcnTxEnable, which is defined as a truth value and configured by the network management, determines whether the IEEE 802.1 organizationally defined Quantitized Congestion Notification TLV transmission is allowed on a given LLDP transmission capable port. The value of this object is restored from non-volatile storage after a re-initialization of the management system. |
| EQL eqlDcbxAdminTCSupported | 1.3.6.1.4.1.12740.19.1.1.1.7 | EqlDcbxSupportedCapacity | read-write | This field is deprecated. |
| EQL eqlDcbxAdminETSConMaxTCG | 1.3.6.1.4.1.12740.19.1.1.1.8 | EqlDcbxSupportedCapacity | read-write | Indicates the number of Traffic Class Groups supported on the remote system. A value of 0 indicates that 8 Traffic Class Groups are supported. |
| T/F eqlDcbxAdminETSConWilling | 1.3.6.1.4.1.12740.19.1.1.1.9 | TruthValue | read-write | Indicates if the local system is willing to accept the ETS configuration recommended by the remote system. |
| OCT eqlDcbxAdminETSConTrafficClassGroupBandwidthTable | 1.3.6.1.4.1.12740.19.1.1.1.10 | OCTET STRING | read-write | Each octet corresponds to one traffic class group. The first octet corresponds to traffic class group 0, the second to traffic class group 1, and so on. Each octet contains the bandwidth in percent to be allocated to the traffic class group. Valid values are between 0 and 100 inclusive. The total of all eight octets must equal 100. Note that an octet string is used instead of a table to enable atomic programming of these values which is required to fulfill the requirement that they always total to 100. |
| OCT eqlDcbxAdminETSRecoTrafficClassGroupBandwidthTable | 1.3.6.1.4.1.12740.19.1.1.1.11 | OCTET STRING | read-write | Each octet corresponds to one traffic class group. The first octet corresponds to traffic class group 0, the second to traffic class group 1, and so on. Each octet contains the bandwidth in percent that the remote station is recommending to be allocated to the traffic class group. Valid values are between 0 and 100 inclusive. The total of all eight octets must equal 100. Note that an octet string is used instead of a table to enable atomic programming of these values which is required to fulfill the requirement that they always total to 100. |
| T/F eqlDcbxAdminPFCWilling | 1.3.6.1.4.1.12740.19.1.1.1.12 | TruthValue | read-write | Indicates if the local system is willing to accept the PFC configuration of the remote system. |
| T/F eqlDcbxAdminPFCMBC | 1.3.6.1.4.1.12740.19.1.1.1.13 | TruthValue | read-write | Indicates if the local system is capable of bypassing MACSEC processing when MACSEC is disabled. |
| EQL eqlDcbxAdminPFCCap | 1.3.6.1.4.1.12740.19.1.1.1.14 | EqlDcbxSupportedCapacity | read-write | Indicates the number of traffic classes on the local device that may simultaneously have PFC enabled. |
| T/F eqlDcbxAdminAppPriorityWilling | 1.3.6.1.4.1.12740.19.1.1.1.15 | TruthValue | read-write | Indicates if the local system is willing to accept the Application Priority configuration of the remote system. |
| T/F eqlDcbxConfigAutoDetectVLANEnable | 1.3.6.1.4.1.12740.19.1.1.1.16 | TruthValue | read-write | Enable automatic detection of VLAN ID. |
| OID eqlDcbxConfigVLANId | 1.3.6.1.4.1.12740.19.1.1.1.17 | EqlVlanIdentifier | read-write | VLAN ID to use for DCB. |
| EQL eqlDcbxAdminETSConTrafficClassGroupPri0 | 1.3.6.1.4.1.12740.19.1.1.1.18 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 0 is to be assigned. |
| EQL eqlDcbxAdminETSConTrafficClassGroupPri1 | 1.3.6.1.4.1.12740.19.1.1.1.19 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 1 is to be assigned. |
| EQL eqlDcbxAdminETSConTrafficClassGroupPri2 | 1.3.6.1.4.1.12740.19.1.1.1.20 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 2 is to be assigned. |
| EQL eqlDcbxAdminETSConTrafficClassGroupPri3 | 1.3.6.1.4.1.12740.19.1.1.1.21 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 3 is to be assigned. |
| EQL eqlDcbxAdminETSConTrafficClassGroupPri4 | 1.3.6.1.4.1.12740.19.1.1.1.22 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 4 is to be assigned. |
| EQL eqlDcbxAdminETSConTrafficClassGroupPri5 | 1.3.6.1.4.1.12740.19.1.1.1.23 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 5 is to be assigned. |
| EQL eqlDcbxAdminETSConTrafficClassGroupPri6 | 1.3.6.1.4.1.12740.19.1.1.1.24 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 6 is to be assigned. |
| EQL eqlDcbxAdminETSConTrafficClassGroupPri7 | 1.3.6.1.4.1.12740.19.1.1.1.25 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 7 is to be assigned. |
| T/F eqlDcbxAdminPFCEnableEnabledPri0 | 1.3.6.1.4.1.12740.19.1.1.1.26 | TruthValue | read-write | Indicates if PFC is enabled on priority 0 |
| T/F eqlDcbxAdminPFCEnableEnabledPri1 | 1.3.6.1.4.1.12740.19.1.1.1.27 | TruthValue | read-write | Indicates if PFC is enabled on priority 1 |
| T/F eqlDcbxAdminPFCEnableEnabledPri2 | 1.3.6.1.4.1.12740.19.1.1.1.28 | TruthValue | read-write | Indicates if PFC is enabled on priority 2 |
| T/F eqlDcbxAdminPFCEnableEnabledPri3 | 1.3.6.1.4.1.12740.19.1.1.1.29 | TruthValue | read-write | Indicates if PFC is enabled on priority 3 |
| T/F eqlDcbxAdminPFCEnableEnabledPri4 | 1.3.6.1.4.1.12740.19.1.1.1.30 | TruthValue | read-write | Indicates if PFC is enabled on priority 4 |
| T/F eqlDcbxAdminPFCEnableEnabledPri5 | 1.3.6.1.4.1.12740.19.1.1.1.31 | TruthValue | read-write | Indicates if PFC is enabled on priority 5 |
| T/F eqlDcbxAdminPFCEnableEnabledPri6 | 1.3.6.1.4.1.12740.19.1.1.1.32 | TruthValue | read-write | Indicates if PFC is enabled on priority 6 |
| T/F eqlDcbxAdminPFCEnableEnabledPri7 | 1.3.6.1.4.1.12740.19.1.1.1.33 | TruthValue | read-write | Indicates if PFC is enabled on priority 7 |
| T/F eqlDcbxAdminAppPriorityiSCSITxEnable | 1.3.6.1.4.1.12740.19.1.1.1.34 | TruthValue | read-write | Indicates whether or not the iSCSI application priority entry is transmitted as part ot the Application Priority TLV. |
| EQL eqlDcbxAdminAppPriorityiSCSIProtocol | 1.3.6.1.4.1.12740.19.1.1.1.35 | EqlDcbxAppProtocol | read-write | The protocol indicator used for iSCSI in the Application Priority TLV. |
| EQL eqlDcbxAdminAppPriorityiSCSIPriority | 1.3.6.1.4.1.12740.19.1.1.1.36 | EqlIEEE8021PriorityValue | read-write | The priority value used for iSCSI in the Application Priority TLV. |
| T/F eqlDcbxAdminAppPriorityFCoETxEnable | 1.3.6.1.4.1.12740.19.1.1.1.37 | TruthValue | read-write | Indicates whether or not the FCoE application priority entry is transmitted as part ot the Application Priority TLV. |
| EQL eqlDcbxAdminAppPriorityFCoEProtocol | 1.3.6.1.4.1.12740.19.1.1.1.38 | EqlDcbxAppProtocol | read-write | The protocol indicator used for FCoE in the Application Priority TLV. |
| EQL eqlDcbxAdminAppPriorityFCoEPriority | 1.3.6.1.4.1.12740.19.1.1.1.39 | EqlIEEE8021PriorityValue | read-write | The priority value used for FCoE in the Application Priority TLV. |
| T/F eqlDcbxConfigDCBEnable | 1.3.6.1.4.1.12740.19.1.1.1.40 | TruthValue | read-write | Indicates whether or not DCB is enabled for this interface |
| T/F eqlDcbxConfigDCBX101Enable | 1.3.6.1.4.1.12740.19.1.1.1.41 | TruthValue | read-write | Indicates whether or not the transmit of DCBX 1.01 TLVs is enabled. |
| T/F eqlDcbxConfigDCBXIEEEDraftEnable | 1.3.6.1.4.1.12740.19.1.1.1.42 | TruthValue | read-write | Indicates whether or not the transmit of DCBX IEEE 802.1Qaz draft TLVs is enabled. |
| EQL eqlDcbxConfigQcnSubtype | 1.3.6.1.4.1.12740.19.1.1.1.43 | EqlIEEEDraftSubtypeValue | read-write | This field is deprecated. |
| EQL eqlDcbxConfigETSConSubtype | 1.3.6.1.4.1.12740.19.1.1.1.44 | EqlIEEEDraftSubtypeValue | read-write | This field is deprecated. |
| EQL eqlDcbxConfigETSRecoSubtype | 1.3.6.1.4.1.12740.19.1.1.1.45 | EqlIEEEDraftSubtypeValue | read-write | This field is deprecated. |
| EQL eqlDcbxConfigPFCSubtype | 1.3.6.1.4.1.12740.19.1.1.1.46 | EqlIEEEDraftSubtypeValue | read-write | This field is deprecated. |
| EQL eqlDcbxConfigAppPrioritySubtype | 1.3.6.1.4.1.12740.19.1.1.1.47 | EqlIEEEDraftSubtypeValue | read-write | This field is deprecated. |
| EQL eqlDcbxConfigTCSupportedSubtype | 1.3.6.1.4.1.12740.19.1.1.1.48 | EqlIEEEDraftSubtypeValue | read-write | This field is deprecated. |
| EQL eqlDcbxAdminETSRecoTrafficClassGroupPri0 | 1.3.6.1.4.1.12740.19.1.1.1.49 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 0 is to be assigned. |
| EQL eqlDcbxAdminETSRecoTrafficClassGroupPri1 | 1.3.6.1.4.1.12740.19.1.1.1.50 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 1 is to be assigned. |
| EQL eqlDcbxAdminETSRecoTrafficClassGroupPri2 | 1.3.6.1.4.1.12740.19.1.1.1.51 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 2 is to be assigned. |
| EQL eqlDcbxAdminETSRecoTrafficClassGroupPri3 | 1.3.6.1.4.1.12740.19.1.1.1.52 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 3 is to be assigned. |
| EQL eqlDcbxAdminETSRecoTrafficClassGroupPri4 | 1.3.6.1.4.1.12740.19.1.1.1.53 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 4 is to be assigned. |
| EQL eqlDcbxAdminETSRecoTrafficClassGroupPri5 | 1.3.6.1.4.1.12740.19.1.1.1.54 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 5 is to be assigned. |
| EQL eqlDcbxAdminETSRecoTrafficClassGroupPri6 | 1.3.6.1.4.1.12740.19.1.1.1.55 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 6 is to be assigned. |
| EQL eqlDcbxAdminETSRecoTrafficClassGroupPri7 | 1.3.6.1.4.1.12740.19.1.1.1.56 | EqlDcbxTrafficClassGroupValue | read-write | Indicates the traffic class group to which priority 7 is to be assigned. |
| T/F eqlDcbCnGlobalMasterEnable | 1.3.6.1.4.1.12740.19.1.1.1.57 | TruthValue | read-write | The state of the congestion notification feature on this bridge component or system. If true, Congestion notification is enabled, and if false, congestion notification is disabled. |
| U32 eqlDcbCnRpPortPriMaxRps | 1.3.6.1.4.1.12740.19.1.1.1.58 | Unsigned32 | read-write | An integer controlling the maximum number of Reaction Points allowed for this CNPV on this Port. An end station SHALL not create more than this many Reaction Point on this Port, but it MAY create fewer. |
| T/F eqlDcbCnRpgEnablePri0 | 1.3.6.1.4.1.12740.19.1.1.1.59 | TruthValue | read-write | Controls the rpEnabled variable of the Reaction Point state machines of the Reaction Points (RPs) controlled by this entry as follows: true(1) The rpEnabled variable for the RPs controlled by this object are not held in the FALSE state, thus enabling them to pay attention to received CNMs. false(2) The rpEnabled variable for the RPs controlled by this object are held in the FALSE state, thus disabling them from paying attention to received CNMs. |
| T/F eqlDcbCnRpgEnablePri1 | 1.3.6.1.4.1.12740.19.1.1.1.60 | TruthValue | read-write | Controls the rpEnabled variable of the Reaction Point state machines of the Reaction Points (RPs) controlled by this entry as follows: true(1) The rpEnabled variable for the RPs controlled by this object are not held in the FALSE state, thus enabling them to pay attention to received CNMs. false(2) The rpEnabled variable for the RPs controlled by this object are held in the FALSE state, thus disabling them from paying attention to received CNMs. |
| T/F eqlDcbCnRpgEnablePri2 | 1.3.6.1.4.1.12740.19.1.1.1.61 | TruthValue | read-write | Controls the rpEnabled variable of the Reaction Point state machines of the Reaction Points (RPs) controlled by this entry as follows: true(1) The rpEnabled variable for the RPs controlled by this object are not held in the FALSE state, thus enabling them to pay attention to received CNMs. false(2) The rpEnabled variable for the RPs controlled by this object are held in the FALSE state, thus disabling them from paying attention to received CNMs. |
| T/F eqlDcbCnRpgEnablePri3 | 1.3.6.1.4.1.12740.19.1.1.1.62 | TruthValue | read-write | Controls the rpEnabled variable of the Reaction Point state machines of the Reaction Points (RPs) controlled by this entry as follows: true(1) The rpEnabled variable for the RPs controlled by this object are not held in the FALSE state, thus enabling them to pay attention to received CNMs. false(2) The rpEnabled variable for the RPs controlled by this object are held in the FALSE state, thus disabling them from paying attention to received CNMs. |
| T/F eqlDcbCnRpgEnablePri4 | 1.3.6.1.4.1.12740.19.1.1.1.63 | TruthValue | read-write | Controls the rpEnabled variable of the Reaction Point state machines of the Reaction Points (RPs) controlled by this entry as follows: true(1) The rpEnabled variable for the RPs controlled by this object are not held in the FALSE state, thus enabling them to pay attention to received CNMs. false(2) The rpEnabled variable for the RPs controlled by this object are held in the FALSE state, thus disabling them from paying attention to received CNMs. |
| T/F eqlDcbCnRpgEnablePri5 | 1.3.6.1.4.1.12740.19.1.1.1.64 | TruthValue | read-write | Controls the rpEnabled variable of the Reaction Point state machines of the Reaction Points (RPs) controlled by this entry as follows: true(1) The rpEnabled variable for the RPs controlled by this object are not held in the FALSE state, thus enabling them to pay attention to received CNMs. false(2) The rpEnabled variable for the RPs controlled by this object are held in the FALSE state, thus disabling them from paying attention to received CNMs. |
| T/F eqlDcbCnRpgEnablePri6 | 1.3.6.1.4.1.12740.19.1.1.1.65 | TruthValue | read-write | Controls the rpEnabled variable of the Reaction Point state machines of the Reaction Points (RPs) controlled by this entry as follows: true(1) The rpEnabled variable for the RPs controlled by this object are not held in the FALSE state, thus enabling them to pay attention to received CNMs. false(2) The rpEnabled variable for the RPs controlled by this object are held in the FALSE state, thus disabling them from paying attention to received CNMs. |
| T/F eqlDcbCnRpgEnablePri7 | 1.3.6.1.4.1.12740.19.1.1.1.66 | TruthValue | read-write | Controls the rpEnabled variable of the Reaction Point state machines of the Reaction Points (RPs) controlled by this entry as follows: true(1) The rpEnabled variable for the RPs controlled by this object are not held in the FALSE state, thus enabling them to pay attention to received CNMs. false(2) The rpEnabled variable for the RPs controlled by this object are held in the FALSE state, thus disabling them from paying attention to received CNMs. |
| NUM eqlDcbCnRpgTimeReset | 1.3.6.1.4.1.12740.19.1.1.1.67 | TimeInterval | read-write | This object controls the value for all of the state machine variables, rpgTimeReset, used to reset the timers RpWhile. |
| U32 eqlDcbCnRpgByteReset | 1.3.6.1.4.1.12740.19.1.1.1.68 | Unsigned32 | read-write | This object controls the value for all of the state machine variables, rpgByteReset, used to reset the counters rpByteCount. |
| U32 eqlDcbCnRpgThreshold | 1.3.6.1.4.1.12740.19.1.1.1.69 | Unsigned32 | read-write | This object controls the number of times rpByteStage or rpTimeStage can count before the RP rate control state machine advances states. |
| U32 eqlDcbCnRpgMaxRate | 1.3.6.1.4.1.12740.19.1.1.1.70 | Unsigned32 | read-write | This object controls the maximum rate, in multiples of 1 Mbit/s, at which an RP can transmit. Default value is the speed of the port. A system SHALL support a minimim value for this object that is no larger than 5 Mbits/s (object value 5). This rate includes all bits consequent to transmitting the frame on the LAN, including preamble, inter-frame gap, etc. |
| U32 eqlDcbCnRpgAiRate | 1.3.6.1.4.1.12740.19.1.1.1.71 | Unsigned32 | read-write | This object controls the transmission rate increment in the RPR_ACTIVE_INCREASE state (rpgAiRate) in multiples of 1 Mbit/s. This rate includes all bits consequent to transmitting the frame on the LAN, including preamble, inter-frame gap, etc. |
| U32 eqlDcbCnRpgHaiRate | 1.3.6.1.4.1.12740.19.1.1.1.72 | Unsigned32 | read-write | This object controls the transmission rate increment in the RPR_HYPER_INCREASE state (rpgHaiRate) in multiples of 1 Mbit/s. This rate includes all bits consequent to transmitting the frame on the LAN, including preamble, inter-frame gap, etc. |
| I32 eqlDcbCnRpgGd | 1.3.6.1.4.1.12740.19.1.1.1.73 | Integer32 | read-write | This object controls the number of bits that the value of the Quantized Feedback field received in a CNM PDU is shifted to the right to decrease rpTargetRate. rpgGd is thus 2 to the negative power of this object, e.g., 7 means rpgGd = 1/128. |
| U32 eqlDcbCnRpgMinDecFac | 1.3.6.1.4.1.12740.19.1.1.1.74 | Unsigned32 | read-write | This object controls the minimum factor by which the current RP transmit rate rpCurrentRate can be changed by reception of a Congestion Notification Message. Its integer value represents a percentage, from 1% to 100%. |
| U32 eqlDcbCnRpgMinRate | 1.3.6.1.4.1.12740.19.1.1.1.75 | Unsigned32 | read-write | This object controls the minimum transmission rate (rpgMinRate) in multiples of 1 Mbit/s. A system SHALL support a value for this object that is no larger than 5 Mbit/s per second. This rate includes all bits consequent to transmitting the frame on the LAN, including preamble, inter-frame gap, etc. |
| EQL eqlDcbDefaultiSCSIPriority | 1.3.6.1.4.1.12740.19.1.1.1.76 | EqlIEEE8021PriorityValue | read-write | The default priority value used for iSCSI when no priority value is negotiated through DCBX. |
| EQL eqlDcbDefaultFCoEPriority | 1.3.6.1.4.1.12740.19.1.1.1.77 | EqlIEEE8021PriorityValue | read-write | The default priority value used for FCoE when no priority value is negotiated through DCBX. |
| EQL eqlDcbxAdminETSConTsaTc0 | 1.3.6.1.4.1.12740.19.1.1.1.78 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSConTsaTc1 | 1.3.6.1.4.1.12740.19.1.1.1.79 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSConTsaTc2 | 1.3.6.1.4.1.12740.19.1.1.1.80 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSConTsaTc3 | 1.3.6.1.4.1.12740.19.1.1.1.81 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSConTsaTc4 | 1.3.6.1.4.1.12740.19.1.1.1.82 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSConTsaTc5 | 1.3.6.1.4.1.12740.19.1.1.1.83 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSConTsaTc6 | 1.3.6.1.4.1.12740.19.1.1.1.84 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSConTsaTc7 | 1.3.6.1.4.1.12740.19.1.1.1.85 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSRecoTsaTc0 | 1.3.6.1.4.1.12740.19.1.1.1.86 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSRecoTsaTc1 | 1.3.6.1.4.1.12740.19.1.1.1.87 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSRecoTsaTc2 | 1.3.6.1.4.1.12740.19.1.1.1.88 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSRecoTsaTc3 | 1.3.6.1.4.1.12740.19.1.1.1.89 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSRecoTsaTc4 | 1.3.6.1.4.1.12740.19.1.1.1.90 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSRecoTsaTc5 | 1.3.6.1.4.1.12740.19.1.1.1.91 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSRecoTsaTc6 | 1.3.6.1.4.1.12740.19.1.1.1.92 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxAdminETSRecoTsaTc7 | 1.3.6.1.4.1.12740.19.1.1.1.93 | EqlDcbxTransmissionSelectionAlgorithm | read-write | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| eqlDcbDynamicIfTable | 1.3.6.1.4.1.12740.19.1.2 | not-accessible | EqualLogic-Dynamic A table of DCB information per each interface of a system. Each row in this table supplies values for one port's DCB parameters. | |
| eqlDcbDynamicIfEntry | 1.3.6.1.4.1.12740.19.1.2.1 | not-accessible | An entry in the DCB table, containing information about DCB on a single interface. | |
| C32 eqlDcbPfcRequestsSentEx | 1.3.6.1.4.1.12740.19.1.2.1.1 | Counter32 | read-only | A count of the invoked PFC M_CONTROL.request primitives. |
| C32 eqlDcbPfcIndicationsReceived | 1.3.6.1.4.1.12740.19.1.2.1.2 | Counter32 | read-only | A count of the received PFC M_CONTROL.indication primitives. |
| EQL eqlDcbxLocTCSupported | 1.3.6.1.4.1.12740.19.1.2.1.3 | EqlDcbxSupportedCapacity | read-only | This field is deprecated. |
| EQL eqlDcbxLocETSConMaxTCG | 1.3.6.1.4.1.12740.19.1.2.1.4 | EqlDcbxSupportedCapacity | read-only | Indicates the number of Traffic Class Groups supported on the local system. A value of 0 indicates that 8 Traffic Class Groups are supported. |
| T/F eqlDcbxLocETSConWilling | 1.3.6.1.4.1.12740.19.1.2.1.5 | TruthValue | read-only | Indicates if the local system is willing to accept the ETS configuration recommended by the remote system. |
| OCT eqlDcbxLocETSConTrafficClassGroupBandwidthTable | 1.3.6.1.4.1.12740.19.1.2.1.6 | OCTET STRING | read-only | Each octet corresponds to one traffic class group. The first octet corresponds to traffic class group 0, the second to traffic class group 1, and so on. Each octet contains the bandwidth in percent to be allocated to the traffic class group. Valid values are between 0 and 100 inclusive. The total of all eight octets must equal 100. Note that an octet string is used instead of a table to enable atomic programming of these values which is required to fulfill the requirement that they always total to 100. |
| OCT eqlDcbxLocETSRecoTrafficClassGroupBandwidthTable | 1.3.6.1.4.1.12740.19.1.2.1.7 | OCTET STRING | read-only | Each octet corresponds to one traffic class group. The first octet corresponds to traffic class group 0, the second to traffic class group 1, and so on. Each octet contains the bandwidth in percent that the remote station is recommending to be allocated to the traffic class group. Valid values are between 0 and 100 inclusive. The total of all eight octets must equal 100. Note that an octet string is used instead of a table to enable atomic programming of these values which is required to fulfill the requirement that they always total to 100. |
| T/F eqlDcbxLocPFCWilling | 1.3.6.1.4.1.12740.19.1.2.1.8 | TruthValue | read-only | Indicates if the local system is willing to accept the PFC configuration of the remote system. |
| T/F eqlDcbxLocPFCMBC | 1.3.6.1.4.1.12740.19.1.2.1.9 | TruthValue | read-only | Indicates if the local system is capable of bypassing MACSEC processing when MACSEC is disabled. |
| EQL eqlDcbxLocPFCCap | 1.3.6.1.4.1.12740.19.1.2.1.10 | EqlDcbxSupportedCapacity | read-only | Indicates the number of traffic classes on the local device that may simultaneously have PFC enabled. Zero indicates no limitation, i.e. all available traffic classes may have PFC enabled. |
| T/F eqlDcbxLocAppPriorityWilling | 1.3.6.1.4.1.12740.19.1.2.1.11 | TruthValue | read-only | Indicates if the local system is willing to accept the Application Priority configuration of the remote system. |
| EQL eqlDcbxRemTCSupported | 1.3.6.1.4.1.12740.19.1.2.1.12 | EqlDcbxSupportedCapacity | read-only | This field is deprecated. |
| EQL eqlDcbxRemETSConMaxTCG | 1.3.6.1.4.1.12740.19.1.2.1.13 | EqlDcbxSupportedCapacity | read-only | Indicates the number of Traffic Class Groups supported on the remote system. A value of 0 indicates that 8 Traffic Class Groups are supported. |
| T/F eqlDcbxRemETSConWilling | 1.3.6.1.4.1.12740.19.1.2.1.14 | TruthValue | read-only | Indicates if the remote system is willing to accept the ETS configuration recommended by the remote system. |
| OCT eqlDcbxRemETSConTrafficClassGroupBandwidthTable | 1.3.6.1.4.1.12740.19.1.2.1.15 | OCTET STRING | read-only | Each octet corresponds to one traffic class group. The first octet corresponds to traffic class group 0, the second to traffic class group 1, and so on. Each octet contains the bandwidth in percent to be allocated to the traffic class group. Valid values are between 0 and 100 inclusive. The total of all eight octets must equal 100. Note that an octet string is used instead of a table to enable atomic programming of these values which is required to fulfill the requirement that they always total to 100. |
| OCT eqlDcbxRemETSRecoTrafficClassGroupBandwidthTable | 1.3.6.1.4.1.12740.19.1.2.1.16 | OCTET STRING | read-only | Each octet corresponds to one traffic class group. The first octet corresponds to traffic class group 0, the second to traffic class group 1, and so on. Each octet contains the bandwidth in percent that the remote station is recommending to be allocated to the traffic class group. Valid values are between 0 and 100 inclusive. The total of all eight octets must equal 100. Note that an octet string is used instead of a table to enable atomic programming of these values which is required to fulfill the requirement that they always total to 100. |
| T/F eqlDcbxRemPFCWilling | 1.3.6.1.4.1.12740.19.1.2.1.17 | TruthValue | read-only | Indicates if the remote system is willing to accept the PFC configuration of the local system. |
| T/F eqlDcbxRemPFCMBC | 1.3.6.1.4.1.12740.19.1.2.1.18 | TruthValue | read-only | Indicates if the remote system is capable of bypassing MACSEC processing when MACSEC is disabled. |
| EQL eqlDcbxRemPFCCap | 1.3.6.1.4.1.12740.19.1.2.1.19 | EqlDcbxSupportedCapacity | read-only | Indicates the number of traffic classes on the remote device that may simultaneously have PFC enabled. Zero indicates no limitation, i.e. all available traffic classes may have PFC enabled. |
| T/F eqlDcbxRemAppPriorityWilling | 1.3.6.1.4.1.12740.19.1.2.1.20 | TruthValue | read-only | Indicates if the remote system is willing to accept the Application Priority configuration of the local system. |
| EQL eqlDcbxLocETSConTrafficClassGroupPri0 | 1.3.6.1.4.1.12740.19.1.2.1.21 | EqlDcbxTrafficClassGroupValue | read-only | Indicates the traffic class group to which priority 0 is assigned. |
| EQL eqlDcbxLocETSConTrafficClassGroupPri1 | 1.3.6.1.4.1.12740.19.1.2.1.22 | EqlDcbxTrafficClassGroupValue | read-only | Indicates the traffic class group to which priority 1 is assigned. |
| EQL eqlDcbxLocETSConTrafficClassGroupPri2 | 1.3.6.1.4.1.12740.19.1.2.1.23 | EqlDcbxTrafficClassGroupValue | read-only | Indicates the traffic class group to which priority 2 is assigned. |
| EQL eqlDcbxLocETSConTrafficClassGroupPri3 | 1.3.6.1.4.1.12740.19.1.2.1.24 | EqlDcbxTrafficClassGroupValue | read-only | Indicates the traffic class group to which priority 3 is assigned. |
| EQL eqlDcbxLocETSConTrafficClassGroupPri4 | 1.3.6.1.4.1.12740.19.1.2.1.25 | EqlDcbxTrafficClassGroupValue | read-only | Indicates the traffic class group to which priority 4 is assigned. |
| EQL eqlDcbxLocETSConTrafficClassGroupPri5 | 1.3.6.1.4.1.12740.19.1.2.1.26 | EqlDcbxTrafficClassGroupValue | read-only | Indicates the traffic class group to which priority 5 is to be assigned. |
| EQL eqlDcbxLocETSConTrafficClassGroupPri6 | 1.3.6.1.4.1.12740.19.1.2.1.27 | EqlDcbxTrafficClassGroupValue | read-only | Indicates the traffic class group to which priority 6 is assigned. |
| EQL eqlDcbxLocETSConTrafficClassGroupPri7 | 1.3.6.1.4.1.12740.19.1.2.1.28 | EqlDcbxTrafficClassGroupValue | read-only | Indicates the traffic class group to which priority 7 is assigned. |
| T/F eqlDcbxLocPFCEnableEnabledPri0 | 1.3.6.1.4.1.12740.19.1.2.1.29 | TruthValue | read-only | Indicates if PFC is enabled on priority 0 |
| T/F eqlDcbxLocPFCEnableEnabledPri1 | 1.3.6.1.4.1.12740.19.1.2.1.30 | TruthValue | read-only | Indicates if PFC is enabled on priority 1 |
| T/F eqlDcbxLocPFCEnableEnabledPri2 | 1.3.6.1.4.1.12740.19.1.2.1.31 | TruthValue | read-only | Indicates if PFC is enabled on priority 2 |
| T/F eqlDcbxLocPFCEnableEnabledPri3 | 1.3.6.1.4.1.12740.19.1.2.1.32 | TruthValue | read-only | Indicates if PFC is enabled on priority 3 |
| T/F eqlDcbxLocPFCEnableEnabledPri4 | 1.3.6.1.4.1.12740.19.1.2.1.33 | TruthValue | read-only | Indicates if PFC is enabled on priority 4 |
| T/F eqlDcbxLocPFCEnableEnabledPri5 | 1.3.6.1.4.1.12740.19.1.2.1.34 | TruthValue | read-only | Indicates if PFC is enabled on priority 5 |
| T/F eqlDcbxLocPFCEnableEnabledPri6 | 1.3.6.1.4.1.12740.19.1.2.1.35 | TruthValue | read-only | Indicates if PFC is enabled on priority 6 |
| T/F eqlDcbxLocPFCEnableEnabledPri7 | 1.3.6.1.4.1.12740.19.1.2.1.36 | TruthValue | read-only | Indicates if PFC is enabled on priority 7 |
| OID eqlDcbxLocVLANId | 1.3.6.1.4.1.12740.19.1.2.1.37 | EqlVlanIdentifier | read-only | VLAN ID to use for DCB. |
| EQL eqlDcbxLocVLANState | 1.3.6.1.4.1.12740.19.1.2.1.38 | EqlDcbxVlanState | read-only | State of VLAN tagging. |
| EQL eqlDcbxLocDCBState | 1.3.6.1.4.1.12740.19.1.2.1.39 | EqlDcbxState | read-only | Current state of DCB. |
| EQL eqlDcbxLocPFCState | 1.3.6.1.4.1.12740.19.1.2.1.40 | EqlDcbxState | read-only | Current state of DCB feature PFC. |
| EQL eqlDcbxLocETSState | 1.3.6.1.4.1.12740.19.1.2.1.41 | EqlDcbxState | read-only | Current state of DCB feature ETS. |
| EQL eqlDcbxLocQCNState | 1.3.6.1.4.1.12740.19.1.2.1.42 | EqlDcbxState | read-only | Current state of DCB feature QCN. |
| EQL eqlDcbxLociSCSIPriority | 1.3.6.1.4.1.12740.19.1.2.1.43 | EqlIEEE8021PriorityValue | read-only | Current iSCSI priority. |
| EQL eqlDcbxLocFCoEPriority | 1.3.6.1.4.1.12740.19.1.2.1.44 | EqlIEEE8021PriorityValue | read-only | Current state of DCB feature QCN. |
| C64 eqlDcbxLocBytesRxPri0 | 1.3.6.1.4.1.12740.19.1.2.1.45 | Counter64 | read-only | Count of bytes recevied on priority 0. |
| C64 eqlDcbxLocBytesRxPri1 | 1.3.6.1.4.1.12740.19.1.2.1.46 | Counter64 | read-only | Count of bytes recevied on priority 1. |
| C64 eqlDcbxLocBytesRxPri2 | 1.3.6.1.4.1.12740.19.1.2.1.47 | Counter64 | read-only | Count of bytes recevied on priority 2. |
| C64 eqlDcbxLocBytesRxPri3 | 1.3.6.1.4.1.12740.19.1.2.1.48 | Counter64 | read-only | Count of bytes recevied on priority 3. |
| C64 eqlDcbxLocBytesRxPri4 | 1.3.6.1.4.1.12740.19.1.2.1.49 | Counter64 | read-only | Count of bytes recevied on priority 4. |
| C64 eqlDcbxLocBytesRxPri5 | 1.3.6.1.4.1.12740.19.1.2.1.50 | Counter64 | read-only | Count of bytes recevied on priority 5. |
| C64 eqlDcbxLocBytesRxPri6 | 1.3.6.1.4.1.12740.19.1.2.1.51 | Counter64 | read-only | Count of bytes recevied on priority 6. |
| C64 eqlDcbxLocBytesRxPri7 | 1.3.6.1.4.1.12740.19.1.2.1.52 | Counter64 | read-only | Count of bytes recevied on priority 7. |
| C64 eqlDcbxLocBytesTxPri0 | 1.3.6.1.4.1.12740.19.1.2.1.53 | Counter64 | read-only | Count of bytes transmitted on priority 0. |
| C64 eqlDcbxLocBytesTxPri1 | 1.3.6.1.4.1.12740.19.1.2.1.54 | Counter64 | read-only | Count of bytes transmitted on priority 1. |
| C64 eqlDcbxLocBytesTxPri2 | 1.3.6.1.4.1.12740.19.1.2.1.55 | Counter64 | read-only | Count of bytes transmitted on priority 2. |
| C64 eqlDcbxLocBytesTxPri3 | 1.3.6.1.4.1.12740.19.1.2.1.56 | Counter64 | read-only | Count of bytes transmitted on priority 3. |
| C64 eqlDcbxLocBytesTxPri4 | 1.3.6.1.4.1.12740.19.1.2.1.57 | Counter64 | read-only | Count of bytes transmitted on priority 4. |
| C64 eqlDcbxLocBytesTxPri5 | 1.3.6.1.4.1.12740.19.1.2.1.58 | Counter64 | read-only | Count of bytes transmitted on priority 5. |
| C64 eqlDcbxLocBytesTxPri6 | 1.3.6.1.4.1.12740.19.1.2.1.59 | Counter64 | read-only | Count of bytes transmitted on priority 6. |
| C64 eqlDcbxLocBytesTxPri7 | 1.3.6.1.4.1.12740.19.1.2.1.60 | Counter64 | read-only | Count of bytes transmitted on priority 7. |
| C64 eqlDcbCnRpPortPriCreatedRpsPri0 | 1.3.6.1.4.1.12740.19.1.2.1.61 | Counter64 | read-only | This object returns the number of times any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable set TRUE by the reception of a Congestion Notification Message. Dividing the change in eqlDcbCnRpPortPriCentiseconds by the change in this object over a time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCreatedRpsPri1 | 1.3.6.1.4.1.12740.19.1.2.1.62 | Counter64 | read-only | This object returns the number of times any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable set TRUE by the reception of a Congestion Notification Message. Dividing the change in eqlDcbCnRpPortPriCentiseconds by the change in this object over a time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCreatedRpsPri2 | 1.3.6.1.4.1.12740.19.1.2.1.63 | Counter64 | read-only | This object returns the number of times any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable set TRUE by the reception of a Congestion Notification Message. Dividing the change in eqlDcbCnRpPortPriCentiseconds by the change in this object over a time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCreatedRpsPri3 | 1.3.6.1.4.1.12740.19.1.2.1.64 | Counter64 | read-only | This object returns the number of times any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable set TRUE by the reception of a Congestion Notification Message. Dividing the change in eqlDcbCnRpPortPriCentiseconds by the change in this object over a time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCreatedRpsPri4 | 1.3.6.1.4.1.12740.19.1.2.1.65 | Counter64 | read-only | This object returns the number of times any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable set TRUE by the reception of a Congestion Notification Message. Dividing the change in eqlDcbCnRpPortPriCentiseconds by the change in this object over a time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCreatedRpsPri5 | 1.3.6.1.4.1.12740.19.1.2.1.66 | Counter64 | read-only | This object returns the number of times any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable set TRUE by the reception of a Congestion Notification Message. Dividing the change in eqlDcbCnRpPortPriCentiseconds by the change in this object over a time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCreatedRpsPri6 | 1.3.6.1.4.1.12740.19.1.2.1.67 | Counter64 | read-only | This object returns the number of times any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable set TRUE by the reception of a Congestion Notification Message. Dividing the change in eqlDcbCnRpPortPriCentiseconds by the change in this object over a time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCreatedRpsPri7 | 1.3.6.1.4.1.12740.19.1.2.1.68 | Counter64 | read-only | This object returns the number of times any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable set TRUE by the reception of a Congestion Notification Message. Dividing the change in eqlDcbCnRpPortPriCentiseconds by the change in this object over a time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCentisecondsPri0 | 1.3.6.1.4.1.12740.19.1.2.1.69 | Counter64 | read-only | This object returns the total number of centi-seconds that any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable in the TRUE state. That is, once each centi-second, this counter is incremented by the number of RPs this entry controls that are actively rate limiting output frames. Dividing the change in this object over a time interval by the length of the interval yields the average number of RPs active over that interval. Dividing the change in this object by the change in eqlDcbCnRpPortPriCreatedRps over that same time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCentisecondsPri1 | 1.3.6.1.4.1.12740.19.1.2.1.70 | Counter64 | read-only | This object returns the total number of centi-seconds that any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable in the TRUE state. That is, once each centi-second, this counter is incremented by the number of RPs this entry controls that are actively rate limiting output frames. Dividing the change in this object over a time interval by the length of the interval yields the average number of RPs active over that interval. Dividing the change in this object by the change in eqlDcbCnRpPortPriCreatedRps over that same time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCentisecondsPri2 | 1.3.6.1.4.1.12740.19.1.2.1.71 | Counter64 | read-only | This object returns the total number of centi-seconds that any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable in the TRUE state. That is, once each centi-second, this counter is incremented by the number of RPs this entry controls that are actively rate limiting output frames. Dividing the change in this object over a time interval by the length of the interval yields the average number of RPs active over that interval. Dividing the change in this object by the change in eqlDcbCnRpPortPriCreatedRps over that same time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCentisecondsPri3 | 1.3.6.1.4.1.12740.19.1.2.1.72 | Counter64 | read-only | This object returns the total number of centi-seconds that any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable in the TRUE state. That is, once each centi-second, this counter is incremented by the number of RPs this entry controls that are actively rate limiting output frames. Dividing the change in this object over a time interval by the length of the interval yields the average number of RPs active over that interval. Dividing the change in this object by the change in eqlDcbCnRpPortPriCreatedRps over that same time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCentisecondsPri4 | 1.3.6.1.4.1.12740.19.1.2.1.73 | Counter64 | read-only | This object returns the total number of centi-seconds that any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable in the TRUE state. That is, once each centi-second, this counter is incremented by the number of RPs this entry controls that are actively rate limiting output frames. Dividing the change in this object over a time interval by the length of the interval yields the average number of RPs active over that interval. Dividing the change in this object by the change in eqlDcbCnRpPortPriCreatedRps over that same time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCentisecondsPri5 | 1.3.6.1.4.1.12740.19.1.2.1.74 | Counter64 | read-only | This object returns the total number of centi-seconds that any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable in the TRUE state. That is, once each centi-second, this counter is incremented by the number of RPs this entry controls that are actively rate limiting output frames. Dividing the change in this object over a time interval by the length of the interval yields the average number of RPs active over that interval. Dividing the change in this object by the change in eqlDcbCnRpPortPriCreatedRps over that same time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCentisecondsPri6 | 1.3.6.1.4.1.12740.19.1.2.1.75 | Counter64 | read-only | This object returns the total number of centi-seconds that any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable in the TRUE state. That is, once each centi-second, this counter is incremented by the number of RPs this entry controls that are actively rate limiting output frames. Dividing the change in this object over a time interval by the length of the interval yields the average number of RPs active over that interval. Dividing the change in this object by the change in eqlDcbCnRpPortPriCreatedRps over that same time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbCnRpPortPriCentisecondsPri7 | 1.3.6.1.4.1.12740.19.1.2.1.76 | Counter64 | read-only | This object returns the total number of centi-seconds that any of the Reaction Points (RPs) controlled by this entry has had its rpEnabled variable in the TRUE state. That is, once each centi-second, this counter is incremented by the number of RPs this entry controls that are actively rate limiting output frames. Dividing the change in this object over a time interval by the length of the interval yields the average number of RPs active over that interval. Dividing the change in this object by the change in eqlDcbCnRpPortPriCreatedRps over that same time interval yields the average lifetime of an active RP during that interval. |
| C64 eqlDcbxLocPfcPausePri0 | 1.3.6.1.4.1.12740.19.1.2.1.77 | Counter64 | read-only | Number of time PFC pause frames received for priority 0. |
| C64 eqlDcbxLocPfcPausePri1 | 1.3.6.1.4.1.12740.19.1.2.1.78 | Counter64 | read-only | Number of time PFC pause frames received for priority 1. |
| C64 eqlDcbxLocPfcPausePri2 | 1.3.6.1.4.1.12740.19.1.2.1.79 | Counter64 | read-only | Number of time PFC pause frames received for priority 2. |
| C64 eqlDcbxLocPfcPausePri3 | 1.3.6.1.4.1.12740.19.1.2.1.80 | Counter64 | read-only | Number of time PFC pause frames received for priority 3. |
| C64 eqlDcbxLocPfcPausePri4 | 1.3.6.1.4.1.12740.19.1.2.1.81 | Counter64 | read-only | Number of time PFC pause frames received for priority 4. |
| C64 eqlDcbxLocPfcPausePri5 | 1.3.6.1.4.1.12740.19.1.2.1.82 | Counter64 | read-only | Number of time PFC pause frames received for priority 5. |
| C64 eqlDcbxLocPfcPausePri6 | 1.3.6.1.4.1.12740.19.1.2.1.83 | Counter64 | read-only | Number of time PFC pause frames received for priority 6. |
| C64 eqlDcbxLocPfcPausePri7 | 1.3.6.1.4.1.12740.19.1.2.1.84 | Counter64 | read-only | Number of time PFC pause frames received for priority 7. |
| C64 eqlDcbxLocPfcUnpausePri0 | 1.3.6.1.4.1.12740.19.1.2.1.85 | Counter64 | read-only | Number of time PFC unpause frames received for priority 0. |
| C64 eqlDcbxLocPfcUnpausePri1 | 1.3.6.1.4.1.12740.19.1.2.1.86 | Counter64 | read-only | Number of time PFC unpause frames received for priority 1. |
| C64 eqlDcbxLocPfcUnpausePri2 | 1.3.6.1.4.1.12740.19.1.2.1.87 | Counter64 | read-only | Number of time PFC unpause frames received for priority 2. |
| C64 eqlDcbxLocPfcUnpausePri3 | 1.3.6.1.4.1.12740.19.1.2.1.88 | Counter64 | read-only | Number of time PFC unpause frames received for priority 3. |
| C64 eqlDcbxLocPfcUnpausePri4 | 1.3.6.1.4.1.12740.19.1.2.1.89 | Counter64 | read-only | Number of time PFC unpause frames received for priority 4. |
| C64 eqlDcbxLocPfcUnpausePri5 | 1.3.6.1.4.1.12740.19.1.2.1.90 | Counter64 | read-only | Number of time PFC unpause frames received for priority 5. |
| C64 eqlDcbxLocPfcUnpausePri6 | 1.3.6.1.4.1.12740.19.1.2.1.91 | Counter64 | read-only | Number of time PFC unpause frames received for priority 6. |
| C64 eqlDcbxLocPfcUnpausePri7 | 1.3.6.1.4.1.12740.19.1.2.1.92 | Counter64 | read-only | Number of time PFC unpause frames received for priority 7. |
| EQL eqlDcbxLocETSConTsaTc0 | 1.3.6.1.4.1.12740.19.1.2.1.93 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSConTsaTc1 | 1.3.6.1.4.1.12740.19.1.2.1.94 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSConTsaTc2 | 1.3.6.1.4.1.12740.19.1.2.1.95 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSConTsaTc3 | 1.3.6.1.4.1.12740.19.1.2.1.96 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSConTsaTc4 | 1.3.6.1.4.1.12740.19.1.2.1.97 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSConTsaTc5 | 1.3.6.1.4.1.12740.19.1.2.1.98 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSConTsaTc6 | 1.3.6.1.4.1.12740.19.1.2.1.99 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSConTsaTc7 | 1.3.6.1.4.1.12740.19.1.2.1.100 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSRecoTsaTc0 | 1.3.6.1.4.1.12740.19.1.2.1.101 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSRecoTsaTc1 | 1.3.6.1.4.1.12740.19.1.2.1.102 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSRecoTsaTc2 | 1.3.6.1.4.1.12740.19.1.2.1.103 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSRecoTsaTc3 | 1.3.6.1.4.1.12740.19.1.2.1.104 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSRecoTsaTc4 | 1.3.6.1.4.1.12740.19.1.2.1.105 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSRecoTsaTc5 | 1.3.6.1.4.1.12740.19.1.2.1.106 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSRecoTsaTc6 | 1.3.6.1.4.1.12740.19.1.2.1.107 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocETSRecoTsaTc7 | 1.3.6.1.4.1.12740.19.1.2.1.108 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSConTsaTc0 | 1.3.6.1.4.1.12740.19.1.2.1.109 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSConTsaTc1 | 1.3.6.1.4.1.12740.19.1.2.1.110 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSConTsaTc2 | 1.3.6.1.4.1.12740.19.1.2.1.111 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSConTsaTc3 | 1.3.6.1.4.1.12740.19.1.2.1.112 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSConTsaTc4 | 1.3.6.1.4.1.12740.19.1.2.1.113 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSConTsaTc5 | 1.3.6.1.4.1.12740.19.1.2.1.114 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSConTsaTc6 | 1.3.6.1.4.1.12740.19.1.2.1.115 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSConTsaTc7 | 1.3.6.1.4.1.12740.19.1.2.1.116 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSRecoTsaTc0 | 1.3.6.1.4.1.12740.19.1.2.1.117 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSRecoTsaTc1 | 1.3.6.1.4.1.12740.19.1.2.1.118 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSRecoTsaTc2 | 1.3.6.1.4.1.12740.19.1.2.1.119 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSRecoTsaTc3 | 1.3.6.1.4.1.12740.19.1.2.1.120 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSRecoTsaTc4 | 1.3.6.1.4.1.12740.19.1.2.1.121 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSRecoTsaTc5 | 1.3.6.1.4.1.12740.19.1.2.1.122 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSRecoTsaTc6 | 1.3.6.1.4.1.12740.19.1.2.1.123 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxRemETSRecoTsaTc7 | 1.3.6.1.4.1.12740.19.1.2.1.124 | EqlDcbxTransmissionSelectionAlgorithm | read-only | Indicates the transmission selection algorithm which is assigned to this traffic class. |
| EQL eqlDcbxLocDCBMode | 1.3.6.1.4.1.12740.19.1.2.1.125 | EqlDcbxMode | read-only | Current operating mode of DCB. |
RFC description
Implements IEEE 802.1Qaz Data Center Bridging QoS features on EqualLogic storage systems.
Start monitoring Dell EqualLogic PS-series iSCSI SAN storage array (Data Center Bridging/DCBX) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.