Dell-BRIDGEMIBOBJECTS-MIB

All MIBs › Dell-BRIDGEMIBOBJECTS-MIB

Organization: Dell

Last Updated: 2007-01-02

Category: Technology: Bridging, Vendor: Dell

Description:

Provides bridge MIB object extensions for Layer 2 switching on Dell network devices.

Imported Objects

BridgeId
Timeout
dot1dBasePort	OBJECT-TYPE
dot1dStpPort

From Dell-MIB

rnd	MODULE-IDENTITY

From IF-MIB

InterfaceIndex
ifIndex	OBJECT-TYPE

From Q-BRIDGE-MIB

PortList

From RFC1155-SMI

Counter

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Counter32
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

DisplayString
RowStatus
TruthValue

What Is Dell-BRIDGEMIBOBJECTS-MIB?

Dell-BRIDGEMIBOBJECTS-MIB is a Dell extension to the standard Bridge MIB, adding vendor-specific objects (the "rl" prefix reflects its RapidCity/Redline switching lineage) for Layer 2 switching features such as per-VLAN Spanning Tree and port priority groups on Dell switches. It exposes configuration data for VLAN-aware Spanning Tree Protocol (STP) behavior, port priority group assignments, and STP enable/type settings, plus a trap-variable object for STP-related notifications. Its monitoring value is centered on software/protocol configuration status rather than physical hardware — administrators use it to confirm STP is enabled and operating in the expected mode per VLAN, and to catch misconfigurations that could cause loops or blocked ports. Network engineers working with the Dell-BRIDGEMIBOBJECTS-MIB MIB typically load it alongside the standard BRIDGE-MIB (dot1dBridge) in their management tool, since its object names and semantics parallel and augment that IETF standard. It is deployed on Dell Ethernet switches running Layer 2 switching software in enterprise networks.

IPNetwork Monitor allows you to monitor SNMP objects defined in Dell-BRIDGEMIBOBJECTS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

What Can Be Monitored

per-VLAN spanning tree status
STP enable/type configuration
port priority group assignment
STP topology-change traps

Supported Devices

Dell PowerSwitch E3248P-ON — current-gen access switch, the recommended upgrade path from the EOL N2000-series

Monitoring Examples

An admin would poll rldot1dStpVlanTable/rldot1dStpVlanEntry to check rldot1dStpVlan status and rldot1dStpEnable per VLAN, confirming STP is active where expected. rldot1dPriorityPortGroupTable/rldot1dPriorityPortGroupEntry indexed by rldot1dPriorityPortGroupNumber reveals which ports are grouped for priority-based forwarding decisions. rldot1dStpTrapVariable can be checked to correlate incoming STP-related traps with the specific object that changed, useful when diagnosing an unexpected topology change.

OIDs

OID symbolic	OID numeric	Type	Access	Description
OCT rldot1dDeviceCapabilities	1.3.6.1.4.1.89.57.3.2	OCTET STRING	read-only	Indicates the optional parts of private extension of IEEE 802.1D and 802.1Q that are implemented by this device and are manageable through this MIB. Capabilities that are allowed on a per-port basis are indicated in dot1dPortCapabilities.
rldot1dExtBase	1.3.6.1.4.1.89.57.3
INT rldot1dExtBaseMibVersion	1.3.6.1.4.1.89.57.3.1	INTEGER	read-only	MIB's version, the current version is 1.
rldot1dPriority	1.3.6.1.4.1.89.57.1
INT rldot1dPriorityMibVersion	1.3.6.1.4.1.89.57.1.1	INTEGER	read-only	MIB's version, the current version is 1.
rldot1dPriorityPortGroupEntry	1.3.6.1.4.1.89.57.1.2.1		not-accessible	All ports belonging to a same group have the same User Priority to Traffic Class mapping.
INT rldot1dPriorityPortGroupNumber	1.3.6.1.4.1.89.57.1.2.1.1	INTEGER	read-only	A group, that port belongs to. All ports belonging to a same group have the same User Priority to Traffic Class mapping.
rldot1dPriorityPortGroupTable	1.3.6.1.4.1.89.57.1.2		not-accessible	A list of PortGroupNumber for each port.
rldot1dStp	1.3.6.1.4.1.89.57.2
INT rldot1dStpBpduCount	1.3.6.1.4.1.89.57.2.11	INTEGER	read-write	The number of bpdu that need to received for the link to be considered stable.
INT rldot1dStpBpduType	1.3.6.1.4.1.89.57.2.13.1.8	INTEGER	read-only	Specified the type of BPDU transmitted by this port.
BRI rldot1dStpDesignatedRoot	1.3.6.1.4.1.89.57.2.6.1.5	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
INT rldot1dStpDisabledPortState	1.3.6.1.4.1.89.57.2.26.1.1	INTEGER	read-write	The port's stp state as defined by external application . This state controls what action a port takes on reception of a frame.
rldot1dStpDisabledPortStateEntry	1.3.6.1.4.1.89.57.2.26.1		not-accessible	Defines the contents of each line in the rldot1dStpDisabledPortStateTable table.
rldot1dStpDisabledPortStateTable	1.3.6.1.4.1.89.57.2.26		not-accessible	Define stp port state for each stp disabled interface. This is auxiliary MIB emulates stp enabled port behaviour in ASIC for stp disabled port. The MIB contains only stp disabled ports entries
T/F rldot1dStpEdgeportSupportInStp	1.3.6.1.4.1.89.57.2.20	TruthValue	read-only	If EdgePort is supported in stpCompatible mode .
T/F rldot1dStpEnable	1.3.6.1.4.1.89.57.2.3	TruthValue	read-write	Enable / Disable spanning tree. When working in per vlan mode enable / disable STP per all vlans.
T/F rldot1dStpEnableByDefault	1.3.6.1.4.1.89.57.2.17	TruthValue	read-only	The default value of rldot1dStpEnable .
T/F rldot1dStpExtendedPortNumberFormat	1.3.6.1.4.1.89.57.2.5	TruthValue	read-write	Specifies whether the STP uses the extended port fnumber format.
T/F rldot1dStpFilterBpdu	1.3.6.1.4.1.89.57.2.21	TruthValue	read-write	Specified if the device should filter BPDUs when STP is disabled.
INT rldot1dStpFloodBpduMethod	1.3.6.1.4.1.89.57.2.22	INTEGER	read-write	Specified flooding method: 1 - classic - untagged to all stp disabled ports 2 - bridging -normal bridging.
TIM rldot1dStpForwardDelay	1.3.6.1.4.1.89.57.2.6.1.11	Timeout	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
TIM rldot1dStpHelloTime	1.3.6.1.4.1.89.57.2.6.1.9	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
INT rldot1dStpHoldTime	1.3.6.1.4.1.89.57.2.6.1.10	INTEGER	read-only	This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
TIK rldot1dStpLastChanged	1.3.6.1.4.1.89.57.2.12	TimeTicks	read-only	The last time any object in this table was changed by SNMP or other local management means.
T/F rldot1dStpLoopbackGuardEnable	1.3.6.1.4.1.89.57.2.25	TruthValue	read-write	Define if STP loopback guard feature is globally enabled.
TIM rldot1dStpMaxAge	1.3.6.1.4.1.89.57.2.6.1.8	Timeout	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
INT rldot1dStpMibVersion	1.3.6.1.4.1.89.57.2.1	INTEGER	read-only	MIB's version, the current version is 2.
INT rldot1dStpMonitorTime	1.3.6.1.4.1.89.57.2.10	INTEGER	read-write	Factor of hello-time during which a port is monotored to determine if it is stable.
T/F rldot1dStpPortAutoEdgePort	1.3.6.1.4.1.89.57.2.13.1.10	TruthValue	read-write	If TRUE causes the Port when become up, to enter the blocking state, and if during 3 seconds it doesn't receive a BPDU, it will enter the forwarding state.
T/F rldot1dStpPortBelongToVlanDefault	1.3.6.1.4.1.89.57.2.16	TruthValue	read-only	The default value of rldot1dStpPortMustBelongToVlan .
T/F rldot1dStpPortBpduGuardEnable	1.3.6.1.4.1.89.57.2.24.1.1	TruthValue	read-write	Specified if bpdu guard is enabled on this port.
rldot1dStpPortBpduGuardEntry	1.3.6.1.4.1.89.57.2.24.1		not-accessible	A list of information maintained by every port whether it is bpdu guard.
rldot1dStpPortBpduGuardTable	1.3.6.1.4.1.89.57.2.24		not-accessible	A table that contains for each port whether it is bpdu guard .
INT rldot1dStpPortBpduOperStatus	1.3.6.1.4.1.89.57.2.13.1.12	INTEGER	read-only	Specified BPDU handling operative status for port.
C32 rldot1dStpPortBpduReceived	1.3.6.1.4.1.89.57.2.13.1.6	Counter32	read-only	Specified the number of bpdu received in this port.
C32 rldot1dStpPortBpduSent	1.3.6.1.4.1.89.57.2.13.1.5	Counter32	read-only	Specified the number of bpdu sent from this port.
T/F rldot1dStpPortDampEnable	1.3.6.1.4.1.89.57.2.13.1.2	TruthValue	read-write	Specified if dampening is enabled on this port.
T/F rldot1dStpPortDampStable	1.3.6.1.4.1.89.57.2.13.1.3	TruthValue	read-only	Specified if the port is stable.
rldot1dStpPortEntry	1.3.6.1.4.1.89.57.2.13.1		not-accessible	A list of information maintained by every port about the Spanning Tree Protocol state for that port.
INT rldot1dStpPortFilterBpdu	1.3.6.1.4.1.89.57.2.13.1.4	INTEGER	read-write	Specified if this port should filter bpdus when stp is disabled.
T/F rldot1dStpPortLoopback	1.3.6.1.4.1.89.57.2.13.1.11	TruthValue	read-only	Specified loopback was detected on port. Usable for only a short period of time if stp loopback guard is enabled (since port enters into shutdown state).
T/F rldot1dStpPortMustBelongToVlan	1.3.6.1.4.1.89.57.2.4	TruthValue	read-write	Specifies whether a port must belong to a VLAN in order to participate in the STP.
INT rldot1dStpPortPort	1.3.6.1.4.1.89.57.2.13.1.1	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
T/F rldot1dStpPortRestrictedRole	1.3.6.1.4.1.89.57.2.13.1.9	TruthValue	read-write	If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even if it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected.
INT rldot1dStpPortRole	1.3.6.1.4.1.89.57.2.13.1.7	INTEGER	read-only	Specified the role of this this port.
T/F rldot1dStpPortsEnable	1.3.6.1.4.1.89.57.2.14	TruthValue	read-only	Enable / Disable spanning tree on ports by default .
rldot1dStpPortTable	1.3.6.1.4.1.89.57.2.13		not-accessible	A table that contains extended pair port specific information.
INT rldot1dStpPortToDefault	1.3.6.1.4.1.89.57.2.18	INTEGER	read-write	To order port/s to revert to default setings .
INT rldot1dStpRootCost	1.3.6.1.4.1.89.57.2.6.1.6	INTEGER	read-only	The cost of the path to the root as seen from this bridge.
INT rldot1dStpRootPort	1.3.6.1.4.1.89.57.2.6.1.7	INTEGER	read-only	The port number of the port which offers the lowest cost path from this bridge to the root bridge.
rldot1dStpSeparatedBridges	1.3.6.1.4.1.89.57.2.23
T/F rldot1dStpSeparatedBridgesAutoConfig	1.3.6.1.4.1.89.57.2.23.3	TruthValue	read-write	Enable / Disable Separated Bridges Automatic Configuration.
T/F rldot1dStpSeparatedBridgesEnable	1.3.6.1.4.1.89.57.2.23.2	TruthValue	read-write	Enable / Disable Separated Bridges Feature.
rldot1dStpSeparatedBridgesEntry	1.3.6.1.4.1.89.57.2.23.1.1		not-accessible	Defines the contents of each line in the rlSeparatedBridgesTable table.
T/F rldot1dStpSeparatedBridgesPortEnable	1.3.6.1.4.1.89.57.2.23.1.1.1	TruthValue	read-write	This variable indicates whether the separated bridge feature is enabled on a specified ifIndex.
rldot1dStpSeparatedBridgesTable	1.3.6.1.4.1.89.57.2.23.1		not-accessible	Define if separated bridges feature is enabled for each interface.
INT rldot1dStpSupportedType	1.3.6.1.4.1.89.57.2.19	INTEGER	read-only	The type of stp supported by the device.
T/F rldot1dStpTaggedFlooding	1.3.6.1.4.1.89.57.2.15	TruthValue	read-only	flooding can be done in tagged bpdu .
TIK rldot1dStpTimeSinceTopologyChange	1.3.6.1.4.1.89.57.2.6.1.3	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
CTR rldot1dStpTopChanges	1.3.6.1.4.1.89.57.2.6.1.4	Counter	read-only	The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
rldot1dStpTrapVariable	1.3.6.1.4.1.89.57.2.8
NUM rldot1dStpTrapVrblifIndex	1.3.6.1.4.1.89.57.2.8.1	InterfaceIndex	read-only	The ifIndex of port which STP status was changed
INT rldot1dStpTrapVrblVID	1.3.6.1.4.1.89.57.2.8.2	INTEGER	read-only	The VID of VLAN to which the port belongs which STP status was changed
INT rldot1dStpType	1.3.6.1.4.1.89.57.2.2	INTEGER	read-only	Specifies whether the device supports Spanning Tree per device, or per group.
INT rldot1dStpTypeAfterReset	1.3.6.1.4.1.89.57.2.9	INTEGER	read-write	New mode of spaning tree supported by the device after the next reset.
INT rldot1dStpVlan	1.3.6.1.4.1.89.57.2.6.1.1	INTEGER	read-only	The Vlan index.
T/F rldot1dStpVlanEnable	1.3.6.1.4.1.89.57.2.6.1.2	TruthValue	read-write	Specifies whether this vlan is STP enable or disable
rldot1dStpVlanEntry	1.3.6.1.4.1.89.57.2.6.1		not-accessible	A list of information maintained by every Vlan about the Spanning Tree Protocol state for that Vlan.
BRI rldot1dStpVlanPortDesignatedBridge	1.3.6.1.4.1.89.57.2.7.1.9	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
INT rldot1dStpVlanPortDesignatedCost	1.3.6.1.4.1.89.57.2.7.1.8	INTEGER	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
OCT rldot1dStpVlanPortDesignatedPort	1.3.6.1.4.1.89.57.2.7.1.10	OCTET STRING	read-only	The Port Identifier of the port on the Designated Bridge for this port's segment.
BRI rldot1dStpVlanPortDesignatedRoot	1.3.6.1.4.1.89.57.2.7.1.7	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
INT rldot1dStpVlanPortEnable	1.3.6.1.4.1.89.57.2.7.1.5	INTEGER	read-write	The enabled/disabled status of the port.
rldot1dStpVlanPortEntry	1.3.6.1.4.1.89.57.2.7.1		not-accessible	A list of information maintained by every pair about the Spanning Tree Protocol state for that pair.
CTR rldot1dStpVlanPortForwardTransitions	1.3.6.1.4.1.89.57.2.7.1.11	Counter	read-only	The number of times this port has transitioned from the Learning state to the Forwarding state.
INT rldot1dStpVlanPortPathCost	1.3.6.1.4.1.89.57.2.7.1.6	INTEGER	read-write	The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
INT rldot1dStpVlanPortPort	1.3.6.1.4.1.89.57.2.7.1.2	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
INT rldot1dStpVlanPortPriority	1.3.6.1.4.1.89.57.2.7.1.3	INTEGER	read-write	The value of the priority field which is contained in the more significant 4 bits of the most significant octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of rldot1dStpVlanPort.
INT rldot1dStpVlanPortState	1.3.6.1.4.1.89.57.2.7.1.4	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpVlanPortEnable), this object will have a value of disabled(1).
rldot1dStpVlanPortTable	1.3.6.1.4.1.89.57.2.7		not-accessible	A table that contains pair specific information for the Spanning Tree Protocol.
INT rldot1dStpVlanPortVlan	1.3.6.1.4.1.89.57.2.7.1.1	INTEGER	read-only	The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information.
rldot1dStpVlanTable	1.3.6.1.4.1.89.57.2.6		not-accessible	A table that contains vlan-specific information for the Spanning Tree Protocol.
rldot1dTpAgingTime	1.3.6.1.4.1.89.57.7
INT rldot1dTpAgingTimeMax	1.3.6.1.4.1.89.57.7.2	INTEGER	read-only	The max timeout period in seconds for aging out dynamically learned forwarding information.
INT rldot1dTpAgingTimeMin	1.3.6.1.4.1.89.57.7.1	INTEGER	read-only	The min timeout period in seconds for aging out dynamically learned forwarding information.
rldot1pPriorityMap	1.3.6.1.4.1.89.57.5
rldot1pPriorityMapEntry	1.3.6.1.4.1.89.57.5.2.1		not-accessible	The row definition for this table.
STR rldot1pPriorityMapName	1.3.6.1.4.1.89.57.5.2.1.1	DisplayString	read-only	The map name
POR rldot1pPriorityMapPort	1.3.6.1.4.1.89.57.5.2.1.3	PortList	read-create	the port that the map, is applied on in config
POR rldot1pPriorityMapPortList	1.3.6.1.4.1.89.57.5.2.1.4	PortList	read-only	the ports that the map, is applied on in actual
OCT rldot1pPriorityMapPriority	1.3.6.1.4.1.89.57.5.2.1.2	OCTET STRING	read-create	The map holding the queue
INT rldot1pPriorityMapState	1.3.6.1.4.1.89.57.5.1	INTEGER	read-write	enable / disable
ROW rldot1pPriorityMapStatus	1.3.6.1.4.1.89.57.5.2.1.5	RowStatus	read-create	The status of the table entry. It's used to delete an entry
rldot1pPriorityMapTable	1.3.6.1.4.1.89.57.5.2		not-accessible	This table hold information the priority maps
rldot1sMstp	1.3.6.1.4.1.89.57.6
STR rldot1sMstpConfigurationName	1.3.6.1.4.1.89.57.6.4	SnmpAdminString	read-only	The active configuration name as will be caried in MST BPDU's.
INT rldot1sMstpDesignatedMaxHopes	1.3.6.1.4.1.89.57.6.8	INTEGER	read-only	Max number of hopes that an MST BPDU will travel inside a region.
T/F rldot1sMstpExtPortBoundary	1.3.6.1.4.1.89.57.6.7.1.5	TruthValue	read-only	Indication if the port is conented to to a lan segment outside or inside the region.
INT rldot1sMstpExtPortDesignatedRegionalCost	1.3.6.1.4.1.89.57.6.7.1.4	INTEGER	read-only	The regional path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
BRI rldot1sMstpExtPortDesignatedRegionalRoot	1.3.6.1.4.1.89.57.6.7.1.3	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
rldot1sMstpExtPortEntry	1.3.6.1.4.1.89.57.6.7.1		not-accessible	A list of information maintained by every port of the CIST.
INT rldot1sMstpExtPortInternalAdminPathCost	1.3.6.1.4.1.89.57.6.7.1.6	INTEGER	read-write	The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object dot1dStpPortPathCost, which returns the operational value of the path cost.
INT rldot1sMstpExtPortInternalOperPathCost	1.3.6.1.4.1.89.57.6.7.1.2	INTEGER	read-only	The contribution of this port to the path cost of paths towards the spanning tree regional root which include this port. 802.1S-2002 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
INT rldot1sMstpExtPortPort	1.3.6.1.4.1.89.57.6.7.1.1	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
rldot1sMstpExtPortTable	1.3.6.1.4.1.89.57.6.7		not-accessible	A table that contains MSTP information about ports of the CIST.
INT rldot1sMstpGroup	1.3.6.1.4.1.89.57.6.6.1.2	INTEGER	read-only	Specifid the active group number this vlan belonges to.
BRI rldot1sMstpInstanceDesignatedRoot	1.3.6.1.4.1.89.57.6.1.1.5	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Muliple Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
T/F rldot1sMstpInstanceEnable	1.3.6.1.4.1.89.57.6.1.1.2	TruthValue	read-only	Specifies whether this Instance is STP enable or disable
rldot1sMstpInstanceEntry	1.3.6.1.4.1.89.57.6.1.1		not-accessible	A list of information maintained by every instance about the multiple Spanning Tree Protocol state for that instance.
TIM rldot1sMstpInstanceForwardDelay	1.3.6.1.4.1.89.57.6.1.1.11	Timeout	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
TIM rldot1sMstpInstanceHelloTime	1.3.6.1.4.1.89.57.6.1.1.9	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
INT rldot1sMstpInstanceHoldTime	1.3.6.1.4.1.89.57.6.1.1.10	INTEGER	read-only	This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
INT rldot1sMstpInstanceId	1.3.6.1.4.1.89.57.6.1.1.1	INTEGER	read-only	The Instance index.
TIM rldot1sMstpInstanceMaxAge	1.3.6.1.4.1.89.57.6.1.1.8	Timeout	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
INT rldot1sMStpInstancePortAdminPathCost	1.3.6.1.4.1.89.57.6.2.1.12	INTEGER	read-write	The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object dot1dStpPortPathCost, which returns the operational value of the path cost.
BRI rldot1sMstpInstancePortDesignatedBridge	1.3.6.1.4.1.89.57.6.2.1.9	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
INT rldot1sMstpInstancePortDesignatedCost	1.3.6.1.4.1.89.57.6.2.1.8	INTEGER	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
OCT rldot1sMstpInstancePortDesignatedPort	1.3.6.1.4.1.89.57.6.2.1.10	OCTET STRING	read-only	The Port Identifier of the port on the Designated Bridge for this port's segment.
BRI rldot1sMstpInstancePortDesignatedRoot	1.3.6.1.4.1.89.57.6.2.1.7	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
INT rldot1sMstpInstancePortEnable	1.3.6.1.4.1.89.57.6.2.1.5	INTEGER	read-only	The enabled/disabled status of the port.
rldot1sMstpInstancePortEntry	1.3.6.1.4.1.89.57.6.2.1		not-accessible	A list of information maintained by every pair about the Spanning Tree Protocol state for that pair.
CTR rldot1sMstpInstancePortForwardTransitions	1.3.6.1.4.1.89.57.6.2.1.11	Counter	read-only	The number of times this port has transitioned from the Learning state to the Forwarding state.
INT rldot1sMstpInstancePortMstiId	1.3.6.1.4.1.89.57.6.2.1.1	INTEGER	read-only	The Vlan group number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information.
INT rldot1sMstpInstancePortPathCost	1.3.6.1.4.1.89.57.6.2.1.6	INTEGER	read-only	The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
INT rldot1sMstpInstancePortPort	1.3.6.1.4.1.89.57.6.2.1.2	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
INT rldot1sMstpInstancePortPriority	1.3.6.1.4.1.89.57.6.2.1.3	INTEGER	read-write	The value of the priority field which is contained in the more significant 4 bits of the most significant octet of the (2 octet long) Port ID. The value is a product of 16. The other octet of the Port ID is given by the value of rldot1dStpVlanGroupPort.
INT rldot1sMStpInstancePortRole	1.3.6.1.4.1.89.57.6.2.1.13	INTEGER	read-only	Specify the role of this this port.
INT rldot1sMstpInstancePortState	1.3.6.1.4.1.89.57.6.2.1.4	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpVlanPortEnable), this object will have a value of disabled(1).
rldot1sMstpInstancePortTable	1.3.6.1.4.1.89.57.6.2		not-accessible	A table that contains pair specific information for the Spanning Tree Protocol.
INT rldot1sMstpInstancePriority	1.3.6.1.4.1.89.57.6.1.1.12	INTEGER	read-write	The value of the write-able portion of the Bridge ID, i.e., the first four bits of the first octet of the (8 octet long) Bridge ID.The value is a product of 4096. The next 12 bit are the msti id . The other (last) 6 octets of the Bridge ID are given by the value of dot1dBaseBridgeAddress.
INT rldot1sMstpInstanceRemainingHopes	1.3.6.1.4.1.89.57.6.1.1.13	INTEGER	read-only	This count value determines the amount of hopes the information transmited by this bridge on this instance can travel.
INT rldot1sMstpInstanceRootCost	1.3.6.1.4.1.89.57.6.1.1.6	INTEGER	read-only	The cost of the path to the root as seen from this bridge.
INT rldot1sMstpInstanceRootPort	1.3.6.1.4.1.89.57.6.1.1.7	INTEGER	read-only	The port number of the port which offers the lowest cost path from this bridge to the root bridge.
rldot1sMstpInstanceTable	1.3.6.1.4.1.89.57.6.1		not-accessible	A table that contains Mstp instance specific information for the Multiple Spanning Tree Protocol.
TIK rldot1sMstpInstanceTimeSinceTopologyChange	1.3.6.1.4.1.89.57.6.1.1.3	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the Mstp Instance .
CTR rldot1sMstpInstanceTopChanges	1.3.6.1.4.1.89.57.6.1.1.4	Counter	read-only	The total number of topology changes detected by this Instance since the management entity was last reset or initialized.
rldot1sMstpInstanceVlanEntry	1.3.6.1.4.1.89.57.6.15.1		not-accessible	The entry contains vlan lists per specific MSTP instance.
INT rldot1sMstpInstanceVlanId	1.3.6.1.4.1.89.57.6.15.1.1	INTEGER	read-only	Specifiy the instance number.
VLA rldot1sMstpInstanceVlanId1025To2048	1.3.6.1.4.1.89.57.6.15.1.3	VlanList2	read-only	second VlanId List of specific MSTP instance.
VLA rldot1sMstpInstanceVlanId1To1024	1.3.6.1.4.1.89.57.6.15.1.2	VlanList1	read-only	first VlanId List of specific MSTP instance.
VLA rldot1sMstpInstanceVlanId2049To3072	1.3.6.1.4.1.89.57.6.15.1.4	VlanList3	read-only	third VlanId List of specific MSTP instance.
VLA rldot1sMstpInstanceVlanId3073To4094	1.3.6.1.4.1.89.57.6.15.1.5	VlanList4	read-only	fourth VlanId List of specific MSTP instance.
rldot1sMstpInstanceVlanTable	1.3.6.1.4.1.89.57.6.15		not-accessible	This table contains vlan lists per MSTP instances.
INT rldot1sMstpMaxHopes	1.3.6.1.4.1.89.57.6.3	INTEGER	read-write	Max number of hopes that an MST BPDU will travel inside a region.
INT rldot1sMstpPendingAction	1.3.6.1.4.1.89.57.6.13	INTEGER	read-write	The action to be done with the pending configuration. copyPendingActive - to copy the pending mst configuration to the active one. copyActivePending - to copy the active mst configuration to the pending one.
STR rldot1sMstpPendingConfigurationName	1.3.6.1.4.1.89.57.6.11	SnmpAdminString	read-write	The pending configuration name.
INT rldot1sMstpPendingGroup	1.3.6.1.4.1.89.57.6.6.1.3	INTEGER	read-write	Specifid the pending group number this vlan belonges to.
INT rldot1sMstpPendingRevisionLevel	1.3.6.1.4.1.89.57.6.12	INTEGER	read-write	The pending revision level.
BRI rldot1sMstpRegionalRoot	1.3.6.1.4.1.89.57.6.9	BridgeId	read-only	CIST Regional Root Identifier (13.16.4). The Bridge Identifier of the current CIST Regional Root.
INT rldot1sMstpRegionalRootCost	1.3.6.1.4.1.89.57.6.10	INTEGER	read-only	The CIST path cost from the transmitting Bridge to the CIST Regional Root.
INT rldot1sMstpRemainingHops	1.3.6.1.4.1.89.57.6.14	INTEGER	read-only	This count value determines the amount of hops the information transmitted by this bridge can travel.
INT rldot1sMstpRevisionLevel	1.3.6.1.4.1.89.57.6.5	INTEGER	read-only	The active revision level.
INT rldot1sMstpVlan	1.3.6.1.4.1.89.57.6.6.1.1	INTEGER	read-only	The vlan number of the vlan for which this entry contains Spanning Tree Protocol management information.
rldot1sMstpVlanEntry	1.3.6.1.4.1.89.57.6.6.1		not-accessible	A list of information maintained by every vlan about the group it belongs to.
rldot1sMstpVlanTable	1.3.6.1.4.1.89.57.6.6		not-accessible	A table that contains information about the alocation of vlans to groups.
rldot1wRStp	1.3.6.1.4.1.89.57.4
T/F rldot1wRStpEdgePortStatus	1.3.6.1.4.1.89.57.4.1.1.3	TruthValue	read-write	Specifies whether this port is an Edge Port or not
rldot1wRStpForceVersionEntry	1.3.6.1.4.1.89.57.4.2.1		not-accessible	A list of information maintained by every about the RAPID Spanning Tree Protocol state for that pair.
INT rldot1wRStpForceVersionState	1.3.6.1.4.1.89.57.4.2.1.2	INTEGER	read-write	Specifies whether this Bridge uses the normal RSTP algorithm, or STP Compatibility algorythm: 0 - STP Compatibility 2 - Normal RSTP
rldot1wRStpForceVersionTable	1.3.6.1.4.1.89.57.4.2		not-accessible	A table that contains specific information for the Rapid Spanning Tree Protocol.
INT rldot1wRStpForceVersionVlan	1.3.6.1.4.1.89.57.4.2.1.1	INTEGER	read-only	The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information, If STP per device then only one value of 1 is allowed. If STP per a VLAN then all value of 1..4095 are allowed.
rldot1wRStpVlanEdgePortEntry	1.3.6.1.4.1.89.57.4.1.1		not-accessible	A list of information maintained by every pair about the RAPID Spanning Tree Protocol state for that pair.
INT rldot1wRStpVlanEdgePortPort	1.3.6.1.4.1.89.57.4.1.1.2	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
rldot1wRStpVlanEdgePortTable	1.3.6.1.4.1.89.57.4.1		not-accessible	A table that contains pair specific information for the Rapid Spanning Tree Protocol.
INT rldot1wRStpVlanEdgePortVlan	1.3.6.1.4.1.89.57.4.1.1.1	INTEGER	read-only	The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information, If STP per device then only one value of 1 is allowed. If STP per a VLAN then all value of 1..4095 are allowed.
rlpBridgeMIBObjects	1.3.6.1.4.1.89.57			This private MIB module defines bridge MIB objects private MIBs.

OID symbolic	OID numeric	Type	Access	Description
rlpBridgeMIBObjects	1.3.6.1.4.1.89.57			This private MIB module defines bridge MIB objects private MIBs.
rldot1dPriority	1.3.6.1.4.1.89.57.1
INT rldot1dPriorityMibVersion	1.3.6.1.4.1.89.57.1.1	INTEGER	read-only	MIB's version, the current version is 1.
rldot1dPriorityPortGroupTable	1.3.6.1.4.1.89.57.1.2		not-accessible	A list of PortGroupNumber for each port.
rldot1dPriorityPortGroupEntry	1.3.6.1.4.1.89.57.1.2.1		not-accessible	All ports belonging to a same group have the same User Priority to Traffic Class mapping.
INT rldot1dPriorityPortGroupNumber	1.3.6.1.4.1.89.57.1.2.1.1	INTEGER	read-only	A group, that port belongs to. All ports belonging to a same group have the same User Priority to Traffic Class mapping.
rldot1dStp	1.3.6.1.4.1.89.57.2
INT rldot1dStpMibVersion	1.3.6.1.4.1.89.57.2.1	INTEGER	read-only	MIB's version, the current version is 2.
INT rldot1dStpType	1.3.6.1.4.1.89.57.2.2	INTEGER	read-only	Specifies whether the device supports Spanning Tree per device, or per group.
T/F rldot1dStpEnable	1.3.6.1.4.1.89.57.2.3	TruthValue	read-write	Enable / Disable spanning tree. When working in per vlan mode enable / disable STP per all vlans.
T/F rldot1dStpPortMustBelongToVlan	1.3.6.1.4.1.89.57.2.4	TruthValue	read-write	Specifies whether a port must belong to a VLAN in order to participate in the STP.
T/F rldot1dStpExtendedPortNumberFormat	1.3.6.1.4.1.89.57.2.5	TruthValue	read-write	Specifies whether the STP uses the extended port fnumber format.
rldot1dStpVlanTable	1.3.6.1.4.1.89.57.2.6		not-accessible	A table that contains vlan-specific information for the Spanning Tree Protocol.
rldot1dStpVlanEntry	1.3.6.1.4.1.89.57.2.6.1		not-accessible	A list of information maintained by every Vlan about the Spanning Tree Protocol state for that Vlan.
INT rldot1dStpVlan	1.3.6.1.4.1.89.57.2.6.1.1	INTEGER	read-only	The Vlan index.
T/F rldot1dStpVlanEnable	1.3.6.1.4.1.89.57.2.6.1.2	TruthValue	read-write	Specifies whether this vlan is STP enable or disable
TIK rldot1dStpTimeSinceTopologyChange	1.3.6.1.4.1.89.57.2.6.1.3	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
CTR rldot1dStpTopChanges	1.3.6.1.4.1.89.57.2.6.1.4	Counter	read-only	The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
BRI rldot1dStpDesignatedRoot	1.3.6.1.4.1.89.57.2.6.1.5	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
INT rldot1dStpRootCost	1.3.6.1.4.1.89.57.2.6.1.6	INTEGER	read-only	The cost of the path to the root as seen from this bridge.
INT rldot1dStpRootPort	1.3.6.1.4.1.89.57.2.6.1.7	INTEGER	read-only	The port number of the port which offers the lowest cost path from this bridge to the root bridge.
TIM rldot1dStpMaxAge	1.3.6.1.4.1.89.57.2.6.1.8	Timeout	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
TIM rldot1dStpHelloTime	1.3.6.1.4.1.89.57.2.6.1.9	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
INT rldot1dStpHoldTime	1.3.6.1.4.1.89.57.2.6.1.10	INTEGER	read-only	This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
TIM rldot1dStpForwardDelay	1.3.6.1.4.1.89.57.2.6.1.11	Timeout	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
rldot1dStpVlanPortTable	1.3.6.1.4.1.89.57.2.7		not-accessible	A table that contains pair specific information for the Spanning Tree Protocol.
rldot1dStpVlanPortEntry	1.3.6.1.4.1.89.57.2.7.1		not-accessible	A list of information maintained by every pair about the Spanning Tree Protocol state for that pair.
INT rldot1dStpVlanPortVlan	1.3.6.1.4.1.89.57.2.7.1.1	INTEGER	read-only	The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information.
INT rldot1dStpVlanPortPort	1.3.6.1.4.1.89.57.2.7.1.2	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
INT rldot1dStpVlanPortPriority	1.3.6.1.4.1.89.57.2.7.1.3	INTEGER	read-write	The value of the priority field which is contained in the more significant 4 bits of the most significant octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of rldot1dStpVlanPort.
INT rldot1dStpVlanPortState	1.3.6.1.4.1.89.57.2.7.1.4	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpVlanPortEnable), this object will have a value of disabled(1).
INT rldot1dStpVlanPortEnable	1.3.6.1.4.1.89.57.2.7.1.5	INTEGER	read-write	The enabled/disabled status of the port.
INT rldot1dStpVlanPortPathCost	1.3.6.1.4.1.89.57.2.7.1.6	INTEGER	read-write	The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
BRI rldot1dStpVlanPortDesignatedRoot	1.3.6.1.4.1.89.57.2.7.1.7	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
INT rldot1dStpVlanPortDesignatedCost	1.3.6.1.4.1.89.57.2.7.1.8	INTEGER	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
BRI rldot1dStpVlanPortDesignatedBridge	1.3.6.1.4.1.89.57.2.7.1.9	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
OCT rldot1dStpVlanPortDesignatedPort	1.3.6.1.4.1.89.57.2.7.1.10	OCTET STRING	read-only	The Port Identifier of the port on the Designated Bridge for this port's segment.
CTR rldot1dStpVlanPortForwardTransitions	1.3.6.1.4.1.89.57.2.7.1.11	Counter	read-only	The number of times this port has transitioned from the Learning state to the Forwarding state.
rldot1dStpTrapVariable	1.3.6.1.4.1.89.57.2.8
NUM rldot1dStpTrapVrblifIndex	1.3.6.1.4.1.89.57.2.8.1	InterfaceIndex	read-only	The ifIndex of port which STP status was changed
INT rldot1dStpTrapVrblVID	1.3.6.1.4.1.89.57.2.8.2	INTEGER	read-only	The VID of VLAN to which the port belongs which STP status was changed
INT rldot1dStpTypeAfterReset	1.3.6.1.4.1.89.57.2.9	INTEGER	read-write	New mode of spaning tree supported by the device after the next reset.
INT rldot1dStpMonitorTime	1.3.6.1.4.1.89.57.2.10	INTEGER	read-write	Factor of hello-time during which a port is monotored to determine if it is stable.
INT rldot1dStpBpduCount	1.3.6.1.4.1.89.57.2.11	INTEGER	read-write	The number of bpdu that need to received for the link to be considered stable.
TIK rldot1dStpLastChanged	1.3.6.1.4.1.89.57.2.12	TimeTicks	read-only	The last time any object in this table was changed by SNMP or other local management means.
rldot1dStpPortTable	1.3.6.1.4.1.89.57.2.13		not-accessible	A table that contains extended pair port specific information.
rldot1dStpPortEntry	1.3.6.1.4.1.89.57.2.13.1		not-accessible	A list of information maintained by every port about the Spanning Tree Protocol state for that port.
INT rldot1dStpPortPort	1.3.6.1.4.1.89.57.2.13.1.1	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
T/F rldot1dStpPortDampEnable	1.3.6.1.4.1.89.57.2.13.1.2	TruthValue	read-write	Specified if dampening is enabled on this port.
T/F rldot1dStpPortDampStable	1.3.6.1.4.1.89.57.2.13.1.3	TruthValue	read-only	Specified if the port is stable.
INT rldot1dStpPortFilterBpdu	1.3.6.1.4.1.89.57.2.13.1.4	INTEGER	read-write	Specified if this port should filter bpdus when stp is disabled.
C32 rldot1dStpPortBpduSent	1.3.6.1.4.1.89.57.2.13.1.5	Counter32	read-only	Specified the number of bpdu sent from this port.
C32 rldot1dStpPortBpduReceived	1.3.6.1.4.1.89.57.2.13.1.6	Counter32	read-only	Specified the number of bpdu received in this port.
INT rldot1dStpPortRole	1.3.6.1.4.1.89.57.2.13.1.7	INTEGER	read-only	Specified the role of this this port.
INT rldot1dStpBpduType	1.3.6.1.4.1.89.57.2.13.1.8	INTEGER	read-only	Specified the type of BPDU transmitted by this port.
T/F rldot1dStpPortRestrictedRole	1.3.6.1.4.1.89.57.2.13.1.9	TruthValue	read-write	If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even if it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected.
T/F rldot1dStpPortAutoEdgePort	1.3.6.1.4.1.89.57.2.13.1.10	TruthValue	read-write	If TRUE causes the Port when become up, to enter the blocking state, and if during 3 seconds it doesn't receive a BPDU, it will enter the forwarding state.
T/F rldot1dStpPortLoopback	1.3.6.1.4.1.89.57.2.13.1.11	TruthValue	read-only	Specified loopback was detected on port. Usable for only a short period of time if stp loopback guard is enabled (since port enters into shutdown state).
INT rldot1dStpPortBpduOperStatus	1.3.6.1.4.1.89.57.2.13.1.12	INTEGER	read-only	Specified BPDU handling operative status for port.
T/F rldot1dStpPortsEnable	1.3.6.1.4.1.89.57.2.14	TruthValue	read-only	Enable / Disable spanning tree on ports by default .
T/F rldot1dStpTaggedFlooding	1.3.6.1.4.1.89.57.2.15	TruthValue	read-only	flooding can be done in tagged bpdu .
T/F rldot1dStpPortBelongToVlanDefault	1.3.6.1.4.1.89.57.2.16	TruthValue	read-only	The default value of rldot1dStpPortMustBelongToVlan .
T/F rldot1dStpEnableByDefault	1.3.6.1.4.1.89.57.2.17	TruthValue	read-only	The default value of rldot1dStpEnable .
INT rldot1dStpPortToDefault	1.3.6.1.4.1.89.57.2.18	INTEGER	read-write	To order port/s to revert to default setings .
INT rldot1dStpSupportedType	1.3.6.1.4.1.89.57.2.19	INTEGER	read-only	The type of stp supported by the device.
T/F rldot1dStpEdgeportSupportInStp	1.3.6.1.4.1.89.57.2.20	TruthValue	read-only	If EdgePort is supported in stpCompatible mode .
T/F rldot1dStpFilterBpdu	1.3.6.1.4.1.89.57.2.21	TruthValue	read-write	Specified if the device should filter BPDUs when STP is disabled.
INT rldot1dStpFloodBpduMethod	1.3.6.1.4.1.89.57.2.22	INTEGER	read-write	Specified flooding method: 1 - classic - untagged to all stp disabled ports 2 - bridging -normal bridging.
rldot1dStpSeparatedBridges	1.3.6.1.4.1.89.57.2.23
rldot1dStpSeparatedBridgesTable	1.3.6.1.4.1.89.57.2.23.1		not-accessible	Define if separated bridges feature is enabled for each interface.
rldot1dStpSeparatedBridgesEntry	1.3.6.1.4.1.89.57.2.23.1.1		not-accessible	Defines the contents of each line in the rlSeparatedBridgesTable table.
T/F rldot1dStpSeparatedBridgesPortEnable	1.3.6.1.4.1.89.57.2.23.1.1.1	TruthValue	read-write	This variable indicates whether the separated bridge feature is enabled on a specified ifIndex.
T/F rldot1dStpSeparatedBridgesEnable	1.3.6.1.4.1.89.57.2.23.2	TruthValue	read-write	Enable / Disable Separated Bridges Feature.
T/F rldot1dStpSeparatedBridgesAutoConfig	1.3.6.1.4.1.89.57.2.23.3	TruthValue	read-write	Enable / Disable Separated Bridges Automatic Configuration.
rldot1dStpPortBpduGuardTable	1.3.6.1.4.1.89.57.2.24		not-accessible	A table that contains for each port whether it is bpdu guard .
rldot1dStpPortBpduGuardEntry	1.3.6.1.4.1.89.57.2.24.1		not-accessible	A list of information maintained by every port whether it is bpdu guard.
T/F rldot1dStpPortBpduGuardEnable	1.3.6.1.4.1.89.57.2.24.1.1	TruthValue	read-write	Specified if bpdu guard is enabled on this port.
T/F rldot1dStpLoopbackGuardEnable	1.3.6.1.4.1.89.57.2.25	TruthValue	read-write	Define if STP loopback guard feature is globally enabled.
rldot1dStpDisabledPortStateTable	1.3.6.1.4.1.89.57.2.26		not-accessible	Define stp port state for each stp disabled interface. This is auxiliary MIB emulates stp enabled port behaviour in ASIC for stp disabled port. The MIB contains only stp disabled ports entries
rldot1dStpDisabledPortStateEntry	1.3.6.1.4.1.89.57.2.26.1		not-accessible	Defines the contents of each line in the rldot1dStpDisabledPortStateTable table.
INT rldot1dStpDisabledPortState	1.3.6.1.4.1.89.57.2.26.1.1	INTEGER	read-write	The port's stp state as defined by external application . This state controls what action a port takes on reception of a frame.
rldot1dExtBase	1.3.6.1.4.1.89.57.3
INT rldot1dExtBaseMibVersion	1.3.6.1.4.1.89.57.3.1	INTEGER	read-only	MIB's version, the current version is 1.
OCT rldot1dDeviceCapabilities	1.3.6.1.4.1.89.57.3.2	OCTET STRING	read-only	Indicates the optional parts of private extension of IEEE 802.1D and 802.1Q that are implemented by this device and are manageable through this MIB. Capabilities that are allowed on a per-port basis are indicated in dot1dPortCapabilities.
rldot1wRStp	1.3.6.1.4.1.89.57.4
rldot1wRStpVlanEdgePortTable	1.3.6.1.4.1.89.57.4.1		not-accessible	A table that contains pair specific information for the Rapid Spanning Tree Protocol.
rldot1wRStpVlanEdgePortEntry	1.3.6.1.4.1.89.57.4.1.1		not-accessible	A list of information maintained by every pair about the RAPID Spanning Tree Protocol state for that pair.
INT rldot1wRStpVlanEdgePortVlan	1.3.6.1.4.1.89.57.4.1.1.1	INTEGER	read-only	The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information, If STP per device then only one value of 1 is allowed. If STP per a VLAN then all value of 1..4095 are allowed.
INT rldot1wRStpVlanEdgePortPort	1.3.6.1.4.1.89.57.4.1.1.2	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
T/F rldot1wRStpEdgePortStatus	1.3.6.1.4.1.89.57.4.1.1.3	TruthValue	read-write	Specifies whether this port is an Edge Port or not
rldot1wRStpForceVersionTable	1.3.6.1.4.1.89.57.4.2		not-accessible	A table that contains specific information for the Rapid Spanning Tree Protocol.
rldot1wRStpForceVersionEntry	1.3.6.1.4.1.89.57.4.2.1		not-accessible	A list of information maintained by every about the RAPID Spanning Tree Protocol state for that pair.
INT rldot1wRStpForceVersionVlan	1.3.6.1.4.1.89.57.4.2.1.1	INTEGER	read-only	The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information, If STP per device then only one value of 1 is allowed. If STP per a VLAN then all value of 1..4095 are allowed.
INT rldot1wRStpForceVersionState	1.3.6.1.4.1.89.57.4.2.1.2	INTEGER	read-write	Specifies whether this Bridge uses the normal RSTP algorithm, or STP Compatibility algorythm: 0 - STP Compatibility 2 - Normal RSTP
rldot1pPriorityMap	1.3.6.1.4.1.89.57.5
INT rldot1pPriorityMapState	1.3.6.1.4.1.89.57.5.1	INTEGER	read-write	enable / disable
rldot1pPriorityMapTable	1.3.6.1.4.1.89.57.5.2		not-accessible	This table hold information the priority maps
rldot1pPriorityMapEntry	1.3.6.1.4.1.89.57.5.2.1		not-accessible	The row definition for this table.
STR rldot1pPriorityMapName	1.3.6.1.4.1.89.57.5.2.1.1	DisplayString	read-only	The map name
OCT rldot1pPriorityMapPriority	1.3.6.1.4.1.89.57.5.2.1.2	OCTET STRING	read-create	The map holding the queue
POR rldot1pPriorityMapPort	1.3.6.1.4.1.89.57.5.2.1.3	PortList	read-create	the port that the map, is applied on in config
POR rldot1pPriorityMapPortList	1.3.6.1.4.1.89.57.5.2.1.4	PortList	read-only	the ports that the map, is applied on in actual
ROW rldot1pPriorityMapStatus	1.3.6.1.4.1.89.57.5.2.1.5	RowStatus	read-create	The status of the table entry. It's used to delete an entry
rldot1sMstp	1.3.6.1.4.1.89.57.6
rldot1sMstpInstanceTable	1.3.6.1.4.1.89.57.6.1		not-accessible	A table that contains Mstp instance specific information for the Multiple Spanning Tree Protocol.
rldot1sMstpInstanceEntry	1.3.6.1.4.1.89.57.6.1.1		not-accessible	A list of information maintained by every instance about the multiple Spanning Tree Protocol state for that instance.
INT rldot1sMstpInstanceId	1.3.6.1.4.1.89.57.6.1.1.1	INTEGER	read-only	The Instance index.
T/F rldot1sMstpInstanceEnable	1.3.6.1.4.1.89.57.6.1.1.2	TruthValue	read-only	Specifies whether this Instance is STP enable or disable
TIK rldot1sMstpInstanceTimeSinceTopologyChange	1.3.6.1.4.1.89.57.6.1.1.3	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the Mstp Instance .
CTR rldot1sMstpInstanceTopChanges	1.3.6.1.4.1.89.57.6.1.1.4	Counter	read-only	The total number of topology changes detected by this Instance since the management entity was last reset or initialized.
BRI rldot1sMstpInstanceDesignatedRoot	1.3.6.1.4.1.89.57.6.1.1.5	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Muliple Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
INT rldot1sMstpInstanceRootCost	1.3.6.1.4.1.89.57.6.1.1.6	INTEGER	read-only	The cost of the path to the root as seen from this bridge.
INT rldot1sMstpInstanceRootPort	1.3.6.1.4.1.89.57.6.1.1.7	INTEGER	read-only	The port number of the port which offers the lowest cost path from this bridge to the root bridge.
TIM rldot1sMstpInstanceMaxAge	1.3.6.1.4.1.89.57.6.1.1.8	Timeout	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
TIM rldot1sMstpInstanceHelloTime	1.3.6.1.4.1.89.57.6.1.1.9	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
INT rldot1sMstpInstanceHoldTime	1.3.6.1.4.1.89.57.6.1.1.10	INTEGER	read-only	This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
TIM rldot1sMstpInstanceForwardDelay	1.3.6.1.4.1.89.57.6.1.1.11	Timeout	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
INT rldot1sMstpInstancePriority	1.3.6.1.4.1.89.57.6.1.1.12	INTEGER	read-write	The value of the write-able portion of the Bridge ID, i.e., the first four bits of the first octet of the (8 octet long) Bridge ID.The value is a product of 4096. The next 12 bit are the msti id . The other (last) 6 octets of the Bridge ID are given by the value of dot1dBaseBridgeAddress.
INT rldot1sMstpInstanceRemainingHopes	1.3.6.1.4.1.89.57.6.1.1.13	INTEGER	read-only	This count value determines the amount of hopes the information transmited by this bridge on this instance can travel.
rldot1sMstpInstancePortTable	1.3.6.1.4.1.89.57.6.2		not-accessible	A table that contains pair specific information for the Spanning Tree Protocol.
rldot1sMstpInstancePortEntry	1.3.6.1.4.1.89.57.6.2.1		not-accessible	A list of information maintained by every pair about the Spanning Tree Protocol state for that pair.
INT rldot1sMstpInstancePortMstiId	1.3.6.1.4.1.89.57.6.2.1.1	INTEGER	read-only	The Vlan group number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information.
INT rldot1sMstpInstancePortPort	1.3.6.1.4.1.89.57.6.2.1.2	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
INT rldot1sMstpInstancePortPriority	1.3.6.1.4.1.89.57.6.2.1.3	INTEGER	read-write	The value of the priority field which is contained in the more significant 4 bits of the most significant octet of the (2 octet long) Port ID. The value is a product of 16. The other octet of the Port ID is given by the value of rldot1dStpVlanGroupPort.
INT rldot1sMstpInstancePortState	1.3.6.1.4.1.89.57.6.2.1.4	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpVlanPortEnable), this object will have a value of disabled(1).
INT rldot1sMstpInstancePortEnable	1.3.6.1.4.1.89.57.6.2.1.5	INTEGER	read-only	The enabled/disabled status of the port.
INT rldot1sMstpInstancePortPathCost	1.3.6.1.4.1.89.57.6.2.1.6	INTEGER	read-only	The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
BRI rldot1sMstpInstancePortDesignatedRoot	1.3.6.1.4.1.89.57.6.2.1.7	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
INT rldot1sMstpInstancePortDesignatedCost	1.3.6.1.4.1.89.57.6.2.1.8	INTEGER	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
BRI rldot1sMstpInstancePortDesignatedBridge	1.3.6.1.4.1.89.57.6.2.1.9	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
OCT rldot1sMstpInstancePortDesignatedPort	1.3.6.1.4.1.89.57.6.2.1.10	OCTET STRING	read-only	The Port Identifier of the port on the Designated Bridge for this port's segment.
CTR rldot1sMstpInstancePortForwardTransitions	1.3.6.1.4.1.89.57.6.2.1.11	Counter	read-only	The number of times this port has transitioned from the Learning state to the Forwarding state.
INT rldot1sMStpInstancePortAdminPathCost	1.3.6.1.4.1.89.57.6.2.1.12	INTEGER	read-write	The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object dot1dStpPortPathCost, which returns the operational value of the path cost.
INT rldot1sMStpInstancePortRole	1.3.6.1.4.1.89.57.6.2.1.13	INTEGER	read-only	Specify the role of this this port.
INT rldot1sMstpMaxHopes	1.3.6.1.4.1.89.57.6.3	INTEGER	read-write	Max number of hopes that an MST BPDU will travel inside a region.
STR rldot1sMstpConfigurationName	1.3.6.1.4.1.89.57.6.4	SnmpAdminString	read-only	The active configuration name as will be caried in MST BPDU's.
INT rldot1sMstpRevisionLevel	1.3.6.1.4.1.89.57.6.5	INTEGER	read-only	The active revision level.
rldot1sMstpVlanTable	1.3.6.1.4.1.89.57.6.6		not-accessible	A table that contains information about the alocation of vlans to groups.
rldot1sMstpVlanEntry	1.3.6.1.4.1.89.57.6.6.1		not-accessible	A list of information maintained by every vlan about the group it belongs to.
INT rldot1sMstpVlan	1.3.6.1.4.1.89.57.6.6.1.1	INTEGER	read-only	The vlan number of the vlan for which this entry contains Spanning Tree Protocol management information.
INT rldot1sMstpGroup	1.3.6.1.4.1.89.57.6.6.1.2	INTEGER	read-only	Specifid the active group number this vlan belonges to.
INT rldot1sMstpPendingGroup	1.3.6.1.4.1.89.57.6.6.1.3	INTEGER	read-write	Specifid the pending group number this vlan belonges to.
rldot1sMstpExtPortTable	1.3.6.1.4.1.89.57.6.7		not-accessible	A table that contains MSTP information about ports of the CIST.
rldot1sMstpExtPortEntry	1.3.6.1.4.1.89.57.6.7.1		not-accessible	A list of information maintained by every port of the CIST.
INT rldot1sMstpExtPortPort	1.3.6.1.4.1.89.57.6.7.1.1	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
INT rldot1sMstpExtPortInternalOperPathCost	1.3.6.1.4.1.89.57.6.7.1.2	INTEGER	read-only	The contribution of this port to the path cost of paths towards the spanning tree regional root which include this port. 802.1S-2002 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
BRI rldot1sMstpExtPortDesignatedRegionalRoot	1.3.6.1.4.1.89.57.6.7.1.3	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
INT rldot1sMstpExtPortDesignatedRegionalCost	1.3.6.1.4.1.89.57.6.7.1.4	INTEGER	read-only	The regional path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
T/F rldot1sMstpExtPortBoundary	1.3.6.1.4.1.89.57.6.7.1.5	TruthValue	read-only	Indication if the port is conented to to a lan segment outside or inside the region.
INT rldot1sMstpExtPortInternalAdminPathCost	1.3.6.1.4.1.89.57.6.7.1.6	INTEGER	read-write	The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object dot1dStpPortPathCost, which returns the operational value of the path cost.
INT rldot1sMstpDesignatedMaxHopes	1.3.6.1.4.1.89.57.6.8	INTEGER	read-only	Max number of hopes that an MST BPDU will travel inside a region.
BRI rldot1sMstpRegionalRoot	1.3.6.1.4.1.89.57.6.9	BridgeId	read-only	CIST Regional Root Identifier (13.16.4). The Bridge Identifier of the current CIST Regional Root.
INT rldot1sMstpRegionalRootCost	1.3.6.1.4.1.89.57.6.10	INTEGER	read-only	The CIST path cost from the transmitting Bridge to the CIST Regional Root.
STR rldot1sMstpPendingConfigurationName	1.3.6.1.4.1.89.57.6.11	SnmpAdminString	read-write	The pending configuration name.
INT rldot1sMstpPendingRevisionLevel	1.3.6.1.4.1.89.57.6.12	INTEGER	read-write	The pending revision level.
INT rldot1sMstpPendingAction	1.3.6.1.4.1.89.57.6.13	INTEGER	read-write	The action to be done with the pending configuration. copyPendingActive - to copy the pending mst configuration to the active one. copyActivePending - to copy the active mst configuration to the pending one.
INT rldot1sMstpRemainingHops	1.3.6.1.4.1.89.57.6.14	INTEGER	read-only	This count value determines the amount of hops the information transmitted by this bridge can travel.
rldot1sMstpInstanceVlanTable	1.3.6.1.4.1.89.57.6.15		not-accessible	This table contains vlan lists per MSTP instances.
rldot1sMstpInstanceVlanEntry	1.3.6.1.4.1.89.57.6.15.1		not-accessible	The entry contains vlan lists per specific MSTP instance.
INT rldot1sMstpInstanceVlanId	1.3.6.1.4.1.89.57.6.15.1.1	INTEGER	read-only	Specifiy the instance number.
VLA rldot1sMstpInstanceVlanId1To1024	1.3.6.1.4.1.89.57.6.15.1.2	VlanList1	read-only	first VlanId List of specific MSTP instance.
VLA rldot1sMstpInstanceVlanId1025To2048	1.3.6.1.4.1.89.57.6.15.1.3	VlanList2	read-only	second VlanId List of specific MSTP instance.
VLA rldot1sMstpInstanceVlanId2049To3072	1.3.6.1.4.1.89.57.6.15.1.4	VlanList3	read-only	third VlanId List of specific MSTP instance.
VLA rldot1sMstpInstanceVlanId3073To4094	1.3.6.1.4.1.89.57.6.15.1.5	VlanList4	read-only	fourth VlanId List of specific MSTP instance.
rldot1dTpAgingTime	1.3.6.1.4.1.89.57.7
INT rldot1dTpAgingTimeMin	1.3.6.1.4.1.89.57.7.1	INTEGER	read-only	The min timeout period in seconds for aging out dynamically learned forwarding information.
INT rldot1dTpAgingTimeMax	1.3.6.1.4.1.89.57.7.2	INTEGER	read-only	The max timeout period in seconds for aging out dynamically learned forwarding information.

BridgeId (8)
BRI rldot1dStpDesignatedRoot	1.3.6.1.4.1.89.57.2.6.1.5	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
BRI rldot1dStpVlanPortDesignatedBridge	1.3.6.1.4.1.89.57.2.7.1.9	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
BRI rldot1dStpVlanPortDesignatedRoot	1.3.6.1.4.1.89.57.2.7.1.7	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
BRI rldot1sMstpExtPortDesignatedRegionalRoot	1.3.6.1.4.1.89.57.6.7.1.3	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
BRI rldot1sMstpInstanceDesignatedRoot	1.3.6.1.4.1.89.57.6.1.1.5	BridgeId	read-only	The bridge identifier of the root of the spanning tree as determined by the Muliple Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
BRI rldot1sMstpInstancePortDesignatedBridge	1.3.6.1.4.1.89.57.6.2.1.9	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
BRI rldot1sMstpInstancePortDesignatedRoot	1.3.6.1.4.1.89.57.6.2.1.7	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
BRI rldot1sMstpRegionalRoot	1.3.6.1.4.1.89.57.6.9	BridgeId	read-only	CIST Regional Root Identifier (13.16.4). The Bridge Identifier of the current CIST Regional Root.
Counter (4)
CTR rldot1dStpTopChanges	1.3.6.1.4.1.89.57.2.6.1.4	Counter	read-only	The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
CTR rldot1dStpVlanPortForwardTransitions	1.3.6.1.4.1.89.57.2.7.1.11	Counter	read-only	The number of times this port has transitioned from the Learning state to the Forwarding state.
CTR rldot1sMstpInstancePortForwardTransitions	1.3.6.1.4.1.89.57.6.2.1.11	Counter	read-only	The number of times this port has transitioned from the Learning state to the Forwarding state.
CTR rldot1sMstpInstanceTopChanges	1.3.6.1.4.1.89.57.6.1.1.4	Counter	read-only	The total number of topology changes detected by this Instance since the management entity was last reset or initialized.
Counter32 (2)
C32 rldot1dStpPortBpduReceived	1.3.6.1.4.1.89.57.2.13.1.6	Counter32	read-only	Specified the number of bpdu received in this port.
C32 rldot1dStpPortBpduSent	1.3.6.1.4.1.89.57.2.13.1.5	Counter32	read-only	Specified the number of bpdu sent from this port.
DisplayString (1)
STR rldot1pPriorityMapName	1.3.6.1.4.1.89.57.5.2.1.1	DisplayString	read-only	The map name
INTEGER (66)
INT rldot1dExtBaseMibVersion	1.3.6.1.4.1.89.57.3.1	INTEGER	read-only	MIB's version, the current version is 1.
INT rldot1dPriorityMibVersion	1.3.6.1.4.1.89.57.1.1	INTEGER	read-only	MIB's version, the current version is 1.
INT rldot1dPriorityPortGroupNumber	1.3.6.1.4.1.89.57.1.2.1.1	INTEGER	read-only	A group, that port belongs to. All ports belonging to a same group have the same User Priority to Traffic Class mapping.
INT rldot1dStpBpduCount	1.3.6.1.4.1.89.57.2.11	INTEGER	read-write	The number of bpdu that need to received for the link to be considered stable.
INT rldot1dStpBpduType	1.3.6.1.4.1.89.57.2.13.1.8	INTEGER	read-only	Specified the type of BPDU transmitted by this port.
INT rldot1dStpDisabledPortState	1.3.6.1.4.1.89.57.2.26.1.1	INTEGER	read-write	The port's stp state as defined by external application . This state controls what action a port takes on reception of a frame.
INT rldot1dStpFloodBpduMethod	1.3.6.1.4.1.89.57.2.22	INTEGER	read-write	Specified flooding method: 1 - classic - untagged to all stp disabled ports 2 - bridging -normal bridging.
INT rldot1dStpHoldTime	1.3.6.1.4.1.89.57.2.6.1.10	INTEGER	read-only	This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
INT rldot1dStpMibVersion	1.3.6.1.4.1.89.57.2.1	INTEGER	read-only	MIB's version, the current version is 2.
INT rldot1dStpMonitorTime	1.3.6.1.4.1.89.57.2.10	INTEGER	read-write	Factor of hello-time during which a port is monotored to determine if it is stable.
INT rldot1dStpPortBpduOperStatus	1.3.6.1.4.1.89.57.2.13.1.12	INTEGER	read-only	Specified BPDU handling operative status for port.
INT rldot1dStpPortFilterBpdu	1.3.6.1.4.1.89.57.2.13.1.4	INTEGER	read-write	Specified if this port should filter bpdus when stp is disabled.
INT rldot1dStpPortPort	1.3.6.1.4.1.89.57.2.13.1.1	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
INT rldot1dStpPortRole	1.3.6.1.4.1.89.57.2.13.1.7	INTEGER	read-only	Specified the role of this this port.
INT rldot1dStpPortToDefault	1.3.6.1.4.1.89.57.2.18	INTEGER	read-write	To order port/s to revert to default setings .
INT rldot1dStpRootCost	1.3.6.1.4.1.89.57.2.6.1.6	INTEGER	read-only	The cost of the path to the root as seen from this bridge.
INT rldot1dStpRootPort	1.3.6.1.4.1.89.57.2.6.1.7	INTEGER	read-only	The port number of the port which offers the lowest cost path from this bridge to the root bridge.
INT rldot1dStpSupportedType	1.3.6.1.4.1.89.57.2.19	INTEGER	read-only	The type of stp supported by the device.
INT rldot1dStpTrapVrblVID	1.3.6.1.4.1.89.57.2.8.2	INTEGER	read-only	The VID of VLAN to which the port belongs which STP status was changed
INT rldot1dStpType	1.3.6.1.4.1.89.57.2.2	INTEGER	read-only	Specifies whether the device supports Spanning Tree per device, or per group.
INT rldot1dStpTypeAfterReset	1.3.6.1.4.1.89.57.2.9	INTEGER	read-write	New mode of spaning tree supported by the device after the next reset.
INT rldot1dStpVlan	1.3.6.1.4.1.89.57.2.6.1.1	INTEGER	read-only	The Vlan index.
INT rldot1dStpVlanPortDesignatedCost	1.3.6.1.4.1.89.57.2.7.1.8	INTEGER	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
INT rldot1dStpVlanPortEnable	1.3.6.1.4.1.89.57.2.7.1.5	INTEGER	read-write	The enabled/disabled status of the port.
INT rldot1dStpVlanPortPathCost	1.3.6.1.4.1.89.57.2.7.1.6	INTEGER	read-write	The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
INT rldot1dStpVlanPortPort	1.3.6.1.4.1.89.57.2.7.1.2	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
INT rldot1dStpVlanPortPriority	1.3.6.1.4.1.89.57.2.7.1.3	INTEGER	read-write	The value of the priority field which is contained in the more significant 4 bits of the most significant octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of rldot1dStpVlanPort.
INT rldot1dStpVlanPortState	1.3.6.1.4.1.89.57.2.7.1.4	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpVlanPortEnable), this object will have a value of disabled(1).
INT rldot1dStpVlanPortVlan	1.3.6.1.4.1.89.57.2.7.1.1	INTEGER	read-only	The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information.
INT rldot1dTpAgingTimeMax	1.3.6.1.4.1.89.57.7.2	INTEGER	read-only	The max timeout period in seconds for aging out dynamically learned forwarding information.
INT rldot1dTpAgingTimeMin	1.3.6.1.4.1.89.57.7.1	INTEGER	read-only	The min timeout period in seconds for aging out dynamically learned forwarding information.
INT rldot1pPriorityMapState	1.3.6.1.4.1.89.57.5.1	INTEGER	read-write	enable / disable
INT rldot1sMstpDesignatedMaxHopes	1.3.6.1.4.1.89.57.6.8	INTEGER	read-only	Max number of hopes that an MST BPDU will travel inside a region.
INT rldot1sMstpExtPortDesignatedRegionalCost	1.3.6.1.4.1.89.57.6.7.1.4	INTEGER	read-only	The regional path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
INT rldot1sMstpExtPortInternalAdminPathCost	1.3.6.1.4.1.89.57.6.7.1.6	INTEGER	read-write	The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object dot1dStpPortPathCost, which returns the operational value of the path cost.
INT rldot1sMstpExtPortInternalOperPathCost	1.3.6.1.4.1.89.57.6.7.1.2	INTEGER	read-only	The contribution of this port to the path cost of paths towards the spanning tree regional root which include this port. 802.1S-2002 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
INT rldot1sMstpExtPortPort	1.3.6.1.4.1.89.57.6.7.1.1	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
INT rldot1sMstpGroup	1.3.6.1.4.1.89.57.6.6.1.2	INTEGER	read-only	Specifid the active group number this vlan belonges to.
INT rldot1sMstpInstanceHoldTime	1.3.6.1.4.1.89.57.6.1.1.10	INTEGER	read-only	This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
INT rldot1sMstpInstanceId	1.3.6.1.4.1.89.57.6.1.1.1	INTEGER	read-only	The Instance index.
INT rldot1sMStpInstancePortAdminPathCost	1.3.6.1.4.1.89.57.6.2.1.12	INTEGER	read-write	The administratively assigned value for the contribution of this port to the path cost of paths towards the spanning tree root. Writing a value of '0' assigns the automatically calculated default Path Cost value to the port. If the default Path Cost is being used, this object returns '0' when read. This complements the object dot1dStpPortPathCost, which returns the operational value of the path cost.
INT rldot1sMstpInstancePortDesignatedCost	1.3.6.1.4.1.89.57.6.2.1.8	INTEGER	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
INT rldot1sMstpInstancePortEnable	1.3.6.1.4.1.89.57.6.2.1.5	INTEGER	read-only	The enabled/disabled status of the port.
INT rldot1sMstpInstancePortMstiId	1.3.6.1.4.1.89.57.6.2.1.1	INTEGER	read-only	The Vlan group number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information.
INT rldot1sMstpInstancePortPathCost	1.3.6.1.4.1.89.57.6.2.1.6	INTEGER	read-only	The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
INT rldot1sMstpInstancePortPort	1.3.6.1.4.1.89.57.6.2.1.2	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
INT rldot1sMstpInstancePortPriority	1.3.6.1.4.1.89.57.6.2.1.3	INTEGER	read-write	The value of the priority field which is contained in the more significant 4 bits of the most significant octet of the (2 octet long) Port ID. The value is a product of 16. The other octet of the Port ID is given by the value of rldot1dStpVlanGroupPort.
INT rldot1sMStpInstancePortRole	1.3.6.1.4.1.89.57.6.2.1.13	INTEGER	read-only	Specify the role of this this port.
INT rldot1sMstpInstancePortState	1.3.6.1.4.1.89.57.6.2.1.4	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpVlanPortEnable), this object will have a value of disabled(1).
INT rldot1sMstpInstancePriority	1.3.6.1.4.1.89.57.6.1.1.12	INTEGER	read-write	The value of the write-able portion of the Bridge ID, i.e., the first four bits of the first octet of the (8 octet long) Bridge ID.The value is a product of 4096. The next 12 bit are the msti id . The other (last) 6 octets of the Bridge ID are given by the value of dot1dBaseBridgeAddress.
INT rldot1sMstpInstanceRemainingHopes	1.3.6.1.4.1.89.57.6.1.1.13	INTEGER	read-only	This count value determines the amount of hopes the information transmited by this bridge on this instance can travel.
INT rldot1sMstpInstanceRootCost	1.3.6.1.4.1.89.57.6.1.1.6	INTEGER	read-only	The cost of the path to the root as seen from this bridge.
INT rldot1sMstpInstanceRootPort	1.3.6.1.4.1.89.57.6.1.1.7	INTEGER	read-only	The port number of the port which offers the lowest cost path from this bridge to the root bridge.
INT rldot1sMstpInstanceVlanId	1.3.6.1.4.1.89.57.6.15.1.1	INTEGER	read-only	Specifiy the instance number.
INT rldot1sMstpMaxHopes	1.3.6.1.4.1.89.57.6.3	INTEGER	read-write	Max number of hopes that an MST BPDU will travel inside a region.
INT rldot1sMstpPendingAction	1.3.6.1.4.1.89.57.6.13	INTEGER	read-write	The action to be done with the pending configuration. copyPendingActive - to copy the pending mst configuration to the active one. copyActivePending - to copy the active mst configuration to the pending one.
INT rldot1sMstpPendingGroup	1.3.6.1.4.1.89.57.6.6.1.3	INTEGER	read-write	Specifid the pending group number this vlan belonges to.
INT rldot1sMstpPendingRevisionLevel	1.3.6.1.4.1.89.57.6.12	INTEGER	read-write	The pending revision level.
INT rldot1sMstpRegionalRootCost	1.3.6.1.4.1.89.57.6.10	INTEGER	read-only	The CIST path cost from the transmitting Bridge to the CIST Regional Root.
INT rldot1sMstpRemainingHops	1.3.6.1.4.1.89.57.6.14	INTEGER	read-only	This count value determines the amount of hops the information transmitted by this bridge can travel.
INT rldot1sMstpRevisionLevel	1.3.6.1.4.1.89.57.6.5	INTEGER	read-only	The active revision level.
INT rldot1sMstpVlan	1.3.6.1.4.1.89.57.6.6.1.1	INTEGER	read-only	The vlan number of the vlan for which this entry contains Spanning Tree Protocol management information.
INT rldot1wRStpForceVersionState	1.3.6.1.4.1.89.57.4.2.1.2	INTEGER	read-write	Specifies whether this Bridge uses the normal RSTP algorithm, or STP Compatibility algorythm: 0 - STP Compatibility 2 - Normal RSTP
INT rldot1wRStpForceVersionVlan	1.3.6.1.4.1.89.57.4.2.1.1	INTEGER	read-only	The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information, If STP per device then only one value of 1 is allowed. If STP per a VLAN then all value of 1..4095 are allowed.
INT rldot1wRStpVlanEdgePortPort	1.3.6.1.4.1.89.57.4.1.1.2	INTEGER	read-only	The port number of the port for which this entry contains Spanning Tree Protocol management information.
INT rldot1wRStpVlanEdgePortVlan	1.3.6.1.4.1.89.57.4.1.1.1	INTEGER	read-only	The Vlan number that the port belongs to, and for which this entry contains Spanning Tree Protocol management information, If STP per device then only one value of 1 is allowed. If STP per a VLAN then all value of 1..4095 are allowed.
InterfaceIndex (1)
NUM rldot1dStpTrapVrblifIndex	1.3.6.1.4.1.89.57.2.8.1	InterfaceIndex	read-only	The ifIndex of port which STP status was changed
OCTET STRING (4)
OCT rldot1dDeviceCapabilities	1.3.6.1.4.1.89.57.3.2	OCTET STRING	read-only	Indicates the optional parts of private extension of IEEE 802.1D and 802.1Q that are implemented by this device and are manageable through this MIB. Capabilities that are allowed on a per-port basis are indicated in dot1dPortCapabilities.
OCT rldot1dStpVlanPortDesignatedPort	1.3.6.1.4.1.89.57.2.7.1.10	OCTET STRING	read-only	The Port Identifier of the port on the Designated Bridge for this port's segment.
OCT rldot1pPriorityMapPriority	1.3.6.1.4.1.89.57.5.2.1.2	OCTET STRING	read-create	The map holding the queue
OCT rldot1sMstpInstancePortDesignatedPort	1.3.6.1.4.1.89.57.6.2.1.10	OCTET STRING	read-only	The Port Identifier of the port on the Designated Bridge for this port's segment.
PortList (2)
POR rldot1pPriorityMapPort	1.3.6.1.4.1.89.57.5.2.1.3	PortList	read-create	the port that the map, is applied on in config
POR rldot1pPriorityMapPortList	1.3.6.1.4.1.89.57.5.2.1.4	PortList	read-only	the ports that the map, is applied on in actual
RowStatus (1)
ROW rldot1pPriorityMapStatus	1.3.6.1.4.1.89.57.5.2.1.5	RowStatus	read-create	The status of the table entry. It's used to delete an entry
SnmpAdminString (2)
STR rldot1sMstpConfigurationName	1.3.6.1.4.1.89.57.6.4	SnmpAdminString	read-only	The active configuration name as will be caried in MST BPDU's.
STR rldot1sMstpPendingConfigurationName	1.3.6.1.4.1.89.57.6.11	SnmpAdminString	read-write	The pending configuration name.
Timeout (6)
TIM rldot1dStpForwardDelay	1.3.6.1.4.1.89.57.2.6.1.11	Timeout	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
TIM rldot1dStpHelloTime	1.3.6.1.4.1.89.57.2.6.1.9	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
TIM rldot1dStpMaxAge	1.3.6.1.4.1.89.57.2.6.1.8	Timeout	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
TIM rldot1sMstpInstanceForwardDelay	1.3.6.1.4.1.89.57.6.1.1.11	Timeout	read-only	This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
TIM rldot1sMstpInstanceHelloTime	1.3.6.1.4.1.89.57.6.1.1.9	Timeout	read-only	The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
TIM rldot1sMstpInstanceMaxAge	1.3.6.1.4.1.89.57.6.1.1.8	Timeout	read-only	The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
TimeTicks (3)
TIK rldot1dStpLastChanged	1.3.6.1.4.1.89.57.2.12	TimeTicks	read-only	The last time any object in this table was changed by SNMP or other local management means.
TIK rldot1dStpTimeSinceTopologyChange	1.3.6.1.4.1.89.57.2.6.1.3	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
TIK rldot1sMstpInstanceTimeSinceTopologyChange	1.3.6.1.4.1.89.57.6.1.1.3	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the Mstp Instance .
TruthValue (23)
T/F rldot1dStpEdgeportSupportInStp	1.3.6.1.4.1.89.57.2.20	TruthValue	read-only	If EdgePort is supported in stpCompatible mode .
T/F rldot1dStpEnable	1.3.6.1.4.1.89.57.2.3	TruthValue	read-write	Enable / Disable spanning tree. When working in per vlan mode enable / disable STP per all vlans.
T/F rldot1dStpEnableByDefault	1.3.6.1.4.1.89.57.2.17	TruthValue	read-only	The default value of rldot1dStpEnable .
T/F rldot1dStpExtendedPortNumberFormat	1.3.6.1.4.1.89.57.2.5	TruthValue	read-write	Specifies whether the STP uses the extended port fnumber format.
T/F rldot1dStpFilterBpdu	1.3.6.1.4.1.89.57.2.21	TruthValue	read-write	Specified if the device should filter BPDUs when STP is disabled.
T/F rldot1dStpLoopbackGuardEnable	1.3.6.1.4.1.89.57.2.25	TruthValue	read-write	Define if STP loopback guard feature is globally enabled.
T/F rldot1dStpPortAutoEdgePort	1.3.6.1.4.1.89.57.2.13.1.10	TruthValue	read-write	If TRUE causes the Port when become up, to enter the blocking state, and if during 3 seconds it doesn't receive a BPDU, it will enter the forwarding state.
T/F rldot1dStpPortBelongToVlanDefault	1.3.6.1.4.1.89.57.2.16	TruthValue	read-only	The default value of rldot1dStpPortMustBelongToVlan .
T/F rldot1dStpPortBpduGuardEnable	1.3.6.1.4.1.89.57.2.24.1.1	TruthValue	read-write	Specified if bpdu guard is enabled on this port.
T/F rldot1dStpPortDampEnable	1.3.6.1.4.1.89.57.2.13.1.2	TruthValue	read-write	Specified if dampening is enabled on this port.
T/F rldot1dStpPortDampStable	1.3.6.1.4.1.89.57.2.13.1.3	TruthValue	read-only	Specified if the port is stable.
T/F rldot1dStpPortLoopback	1.3.6.1.4.1.89.57.2.13.1.11	TruthValue	read-only	Specified loopback was detected on port. Usable for only a short period of time if stp loopback guard is enabled (since port enters into shutdown state).
T/F rldot1dStpPortMustBelongToVlan	1.3.6.1.4.1.89.57.2.4	TruthValue	read-write	Specifies whether a port must belong to a VLAN in order to participate in the STP.
T/F rldot1dStpPortRestrictedRole	1.3.6.1.4.1.89.57.2.13.1.9	TruthValue	read-write	If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even if it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected.
T/F rldot1dStpPortsEnable	1.3.6.1.4.1.89.57.2.14	TruthValue	read-only	Enable / Disable spanning tree on ports by default .
T/F rldot1dStpSeparatedBridgesAutoConfig	1.3.6.1.4.1.89.57.2.23.3	TruthValue	read-write	Enable / Disable Separated Bridges Automatic Configuration.
T/F rldot1dStpSeparatedBridgesEnable	1.3.6.1.4.1.89.57.2.23.2	TruthValue	read-write	Enable / Disable Separated Bridges Feature.
T/F rldot1dStpSeparatedBridgesPortEnable	1.3.6.1.4.1.89.57.2.23.1.1.1	TruthValue	read-write	This variable indicates whether the separated bridge feature is enabled on a specified ifIndex.
T/F rldot1dStpTaggedFlooding	1.3.6.1.4.1.89.57.2.15	TruthValue	read-only	flooding can be done in tagged bpdu .
T/F rldot1dStpVlanEnable	1.3.6.1.4.1.89.57.2.6.1.2	TruthValue	read-write	Specifies whether this vlan is STP enable or disable
T/F rldot1sMstpExtPortBoundary	1.3.6.1.4.1.89.57.6.7.1.5	TruthValue	read-only	Indication if the port is conented to to a lan segment outside or inside the region.
T/F rldot1sMstpInstanceEnable	1.3.6.1.4.1.89.57.6.1.1.2	TruthValue	read-only	Specifies whether this Instance is STP enable or disable
T/F rldot1wRStpEdgePortStatus	1.3.6.1.4.1.89.57.4.1.1.3	TruthValue	read-write	Specifies whether this port is an Edge Port or not
VlanList1 (1)
VLA rldot1sMstpInstanceVlanId1To1024	1.3.6.1.4.1.89.57.6.15.1.2	VlanList1	read-only	first VlanId List of specific MSTP instance.
VlanList2 (1)
VLA rldot1sMstpInstanceVlanId1025To2048	1.3.6.1.4.1.89.57.6.15.1.3	VlanList2	read-only	second VlanId List of specific MSTP instance.
VlanList3 (1)
VLA rldot1sMstpInstanceVlanId2049To3072	1.3.6.1.4.1.89.57.6.15.1.4	VlanList3	read-only	third VlanId List of specific MSTP instance.
VlanList4 (1)
VLA rldot1sMstpInstanceVlanId3073To4094	1.3.6.1.4.1.89.57.6.15.1.5	VlanList4	read-only	fourth VlanId List of specific MSTP instance.
No type (40)
rldot1dExtBase	1.3.6.1.4.1.89.57.3
rldot1dPriority	1.3.6.1.4.1.89.57.1
rldot1dPriorityPortGroupEntry	1.3.6.1.4.1.89.57.1.2.1		not-accessible	All ports belonging to a same group have the same User Priority to Traffic Class mapping.
rldot1dPriorityPortGroupTable	1.3.6.1.4.1.89.57.1.2		not-accessible	A list of PortGroupNumber for each port.
rldot1dStp	1.3.6.1.4.1.89.57.2
rldot1dStpDisabledPortStateEntry	1.3.6.1.4.1.89.57.2.26.1		not-accessible	Defines the contents of each line in the rldot1dStpDisabledPortStateTable table.
rldot1dStpDisabledPortStateTable	1.3.6.1.4.1.89.57.2.26		not-accessible	Define stp port state for each stp disabled interface. This is auxiliary MIB emulates stp enabled port behaviour in ASIC for stp disabled port. The MIB contains only stp disabled ports entries
rldot1dStpPortBpduGuardEntry	1.3.6.1.4.1.89.57.2.24.1		not-accessible	A list of information maintained by every port whether it is bpdu guard.
rldot1dStpPortBpduGuardTable	1.3.6.1.4.1.89.57.2.24		not-accessible	A table that contains for each port whether it is bpdu guard .
rldot1dStpPortEntry	1.3.6.1.4.1.89.57.2.13.1		not-accessible	A list of information maintained by every port about the Spanning Tree Protocol state for that port.
rldot1dStpPortTable	1.3.6.1.4.1.89.57.2.13		not-accessible	A table that contains extended pair port specific information.
rldot1dStpSeparatedBridges	1.3.6.1.4.1.89.57.2.23
rldot1dStpSeparatedBridgesEntry	1.3.6.1.4.1.89.57.2.23.1.1		not-accessible	Defines the contents of each line in the rlSeparatedBridgesTable table.
rldot1dStpSeparatedBridgesTable	1.3.6.1.4.1.89.57.2.23.1		not-accessible	Define if separated bridges feature is enabled for each interface.
rldot1dStpTrapVariable	1.3.6.1.4.1.89.57.2.8
rldot1dStpVlanEntry	1.3.6.1.4.1.89.57.2.6.1		not-accessible	A list of information maintained by every Vlan about the Spanning Tree Protocol state for that Vlan.
rldot1dStpVlanPortEntry	1.3.6.1.4.1.89.57.2.7.1		not-accessible	A list of information maintained by every pair about the Spanning Tree Protocol state for that pair.
rldot1dStpVlanPortTable	1.3.6.1.4.1.89.57.2.7		not-accessible	A table that contains pair specific information for the Spanning Tree Protocol.
rldot1dStpVlanTable	1.3.6.1.4.1.89.57.2.6		not-accessible	A table that contains vlan-specific information for the Spanning Tree Protocol.
rldot1dTpAgingTime	1.3.6.1.4.1.89.57.7
rldot1pPriorityMap	1.3.6.1.4.1.89.57.5
rldot1pPriorityMapEntry	1.3.6.1.4.1.89.57.5.2.1		not-accessible	The row definition for this table.
rldot1pPriorityMapTable	1.3.6.1.4.1.89.57.5.2		not-accessible	This table hold information the priority maps
rldot1sMstp	1.3.6.1.4.1.89.57.6
rldot1sMstpExtPortEntry	1.3.6.1.4.1.89.57.6.7.1		not-accessible	A list of information maintained by every port of the CIST.
rldot1sMstpExtPortTable	1.3.6.1.4.1.89.57.6.7		not-accessible	A table that contains MSTP information about ports of the CIST.
rldot1sMstpInstanceEntry	1.3.6.1.4.1.89.57.6.1.1		not-accessible	A list of information maintained by every instance about the multiple Spanning Tree Protocol state for that instance.
rldot1sMstpInstancePortEntry	1.3.6.1.4.1.89.57.6.2.1		not-accessible	A list of information maintained by every pair about the Spanning Tree Protocol state for that pair.
rldot1sMstpInstancePortTable	1.3.6.1.4.1.89.57.6.2		not-accessible	A table that contains pair specific information for the Spanning Tree Protocol.
rldot1sMstpInstanceTable	1.3.6.1.4.1.89.57.6.1		not-accessible	A table that contains Mstp instance specific information for the Multiple Spanning Tree Protocol.
rldot1sMstpInstanceVlanEntry	1.3.6.1.4.1.89.57.6.15.1		not-accessible	The entry contains vlan lists per specific MSTP instance.
rldot1sMstpInstanceVlanTable	1.3.6.1.4.1.89.57.6.15		not-accessible	This table contains vlan lists per MSTP instances.
rldot1sMstpVlanEntry	1.3.6.1.4.1.89.57.6.6.1		not-accessible	A list of information maintained by every vlan about the group it belongs to.
rldot1sMstpVlanTable	1.3.6.1.4.1.89.57.6.6		not-accessible	A table that contains information about the alocation of vlans to groups.
rldot1wRStp	1.3.6.1.4.1.89.57.4
rldot1wRStpForceVersionEntry	1.3.6.1.4.1.89.57.4.2.1		not-accessible	A list of information maintained by every about the RAPID Spanning Tree Protocol state for that pair.
rldot1wRStpForceVersionTable	1.3.6.1.4.1.89.57.4.2		not-accessible	A table that contains specific information for the Rapid Spanning Tree Protocol.
rldot1wRStpVlanEdgePortEntry	1.3.6.1.4.1.89.57.4.1.1		not-accessible	A list of information maintained by every pair about the RAPID Spanning Tree Protocol state for that pair.
rldot1wRStpVlanEdgePortTable	1.3.6.1.4.1.89.57.4.1		not-accessible	A table that contains pair specific information for the Rapid Spanning Tree Protocol.
rlpBridgeMIBObjects	1.3.6.1.4.1.89.57			This private MIB module defines bridge MIB objects private MIBs.

FAQ

What would I check with Dell-BRIDGEMIBOBJECTS-MIB on a Dell switch to prevent a Layer 2 loop?
It exposes per-VLAN Spanning Tree enable/type settings and port priority group assignments, letting an administrator confirm STP is enabled and operating in the expected mode per VLAN, plus a trap-variable object for STP topology-change notifications.

Is Dell-BRIDGEMIBOBJECTS-MIB used on its own or with the standard Bridge MIB?
It's typically loaded alongside the standard BRIDGE-MIB (dot1dBridge), since its object names and semantics parallel and augment that IETF standard — the "rl" prefix reflects its RapidCity/Redline switching lineage.

RFC description

Dell private MIB module defining bridge management objects for monitoring and managing Dell PowerConnect switches and networking devices.

Start monitoring Dell PowerConnect/Networking managed switch (per-VLAN spanning tree/port priority) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Dell-BRIDGEMIBOBJECTS-MIB

This MIB depends on

Related MIBs

What Is Dell-BRIDGEMIBOBJECTS-MIB?

What Can Be Monitored

Supported Devices

Monitoring Examples

FAQ

RFC description