DATALINK-MIB

All MIBs › DATALINK-MIB

Category: WAN

Description: Manages data link layer interface configuration and error statistics for serial WAN connections.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DATALINK-MIB?

DATALINK-MIB is a vendor enterprise MIB for managing the data link layer of serial WAN connections, appearing to originate from a modem/remote-access product line given its references to modems, network cards, and product identity. It exposes basic device inventory (product name, system/application version) alongside serial-line hardware inventory such as number of ports, network cards, and installed modems, plus per-modem configuration like port speed and setup/AT command strings. It supports monitoring both hardware and software status of the unit — software version (systemversion, appversion) for tracking firmware currency, and hardware health via modemreport and memorysize for detecting a failed or misconfigured modem card or memory exhaustion. It is a self-contained enterprise MIB with no explicit dependency on other MIBs. Typical deployment is a modem bank or remote-access/dial-up router monitored for line and modem availability in a legacy WAN or backup-link scenario. Engineers can download the DATALINK-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DATALINK-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

serial/dial-up modem bank or remote-access router

Monitoring Examples

An admin would poll datalinkThisProduct along with productname/systemversion/appversion to confirm firmware version across a fleet of remote-access units, and check numberports against netcard/modems counts to verify all expected modem hardware is present. modemreport and modemportspeed per modem would be checked to detect a modem that has dropped to a lower negotiated speed or stopped reporting, indicating a line or hardware fault; modemsetupstring confirms the AT command profile in use.

What Can Be Monitored

product/firmware version
installed modem and network card count
modem port speed
modem status report
memory size
network enabled state

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1065-SMI

Counter
Gauge
IpAddress
NetworkAddress
TimeTicks
internet
mgmt
private

From RFC1155-SMI

ObjectName
enterprises

From SNMPv2-TC

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
asentria	1.3.6.1.4.1.3052
NTF datalinkDbasePfullTrap	1.3.6.1.4.1.3052.0.501			The datalinkDbasePfullTrap is issued when the database reaches a pre-determined threshold level, which causes a trap.
NTF datalinkFilePfullTrap	1.3.6.1.4.1.3052.0.502			The datalinkFilePfullTrap is issued when one of the data files reaches a pre-determined threshold level, which causes a trap.
NTF datalinkDataAlarmTrap	1.3.6.1.4.1.3052.0.503			The datalinkDataAlarmTrap is issued when one of the data alarms reaches a pre-determined threshold level, which causes a trap.
NTF datalinkSensorAlarmTrap	1.3.6.1.4.1.3052.0.504			The datalinkSensorAlarmTrap is issued when one of the External Sensors is triggered for a pre-determined threshold amount of time, which causes a trap.
NTF datalinkNoDataAlarmTrap	1.3.6.1.4.1.3052.0.505			The datalinkNoDataAlarmTrap is issued when one of the ports receives no input data for a pre-determined threshold amount of time, which causes a trap.
NTF datalinkSchedTrap	1.3.6.1.4.1.3052.0.506			The datalinkSchedTrap is issued when a scheduled event causes a trap.
NTF datalinkImmediateTrap	1.3.6.1.4.1.3052.0.507			The datalinkImmediateTrap is issued when the dotrap command is used to issue a test trap to all snmp managers
NTF datalinkPPPupTrap	1.3.6.1.4.1.3052.0.509			The datalinkPPPupTrap is issued when the PPP interface is brought up and the ppp connection has been established
datalink	1.3.6.1.4.1.3052.1
productIds	1.3.6.1.4.1.3052.1.1
STR datalinkThisProduct	1.3.6.1.4.1.3052.1.1.1	DisplayString	read-only	This is a factory-configured string for the product name
productConfig	1.3.6.1.4.1.3052.1.2
STR productname	1.3.6.1.4.1.3052.1.2.1	DisplayString	read-only	A second string which may also contain name/version info
INT systemversion	1.3.6.1.4.1.3052.1.2.2	INTEGER	read-only	system rom version number
STR appversion	1.3.6.1.4.1.3052.1.2.3	DisplayString	read-only	application version
hardware	1.3.6.1.4.1.3052.1.2.4
INT numberPorts	1.3.6.1.4.1.3052.1.2.4.1	INTEGER	read-only	number of RS232 ports found
INT netcard	1.3.6.1.4.1.3052.1.2.4.2	INTEGER	read-only	0 if no net card, 1 if net card found
INT modems	1.3.6.1.4.1.3052.1.2.4.3	INTEGER	read-only	0 if no modem, 1 if modem was found
INT networkenabled	1.3.6.1.4.1.3052.1.2.4.4	INTEGER	read-only	0 if not enabled, 1 if enabled
INT memorysize	1.3.6.1.4.1.3052.1.2.4.5	INTEGER	read-only	memory size in K
factorysetup	1.3.6.1.4.1.3052.1.2.5
STR modemreport	1.3.6.1.4.1.3052.1.2.5.1	DisplayString	read-write	5-char string, speed to report for modem speed
INT modemportspeed	1.3.6.1.4.1.3052.1.2.5.2	INTEGER	read-write	modem port baud rate 38400, 19200, etc.
STR modemsetupstring	1.3.6.1.4.1.3052.1.2.5.3	DisplayString	read-write	modem setup string, e.g., ATe0v0s0=1
INT modemcddelay	1.3.6.1.4.1.3052.1.2.5.4	INTEGER	read-write	seconds after CD before sending answer string
INT modemtype	1.3.6.1.4.1.3052.1.2.5.5	INTEGER	read-write	number factory-assigned to this particular modem, manufacturer, etc.
STR serialnumber	1.3.6.1.4.1.3052.1.2.5.6	DisplayString	read-write	up to 10 chars for factory-assigned serial number
STR dateofmanufacture	1.3.6.1.4.1.3052.1.2.5.7	DisplayString	read-write	up to 8 chars for factory-assigned date of manufacture
INT databasemode	1.3.6.1.4.1.3052.1.2.6	INTEGER	read-write	database compatibility mode, 1 -normal, 2 commandset2, etc.
unitIds	1.3.6.1.4.1.3052.1.3
STR datalinkSiteId	1.3.6.1.4.1.3052.1.3.1	DisplayString	read-write	Site ID string
idByPortTable	1.3.6.1.4.1.3052.1.3.2		not-accessible	an id for type of data by port
sitebyport	1.3.6.1.4.1.3052.1.3.2.1		not-accessible	entry for table
INT siteindex	1.3.6.1.4.1.3052.1.3.2.1.1	INTEGER	read-only	index for which port
STR siteID	1.3.6.1.4.1.3052.1.3.2.1.2	DisplayString	read-write	site id or type of data by port
serialPorts	1.3.6.1.4.1.3052.1.4
portSetupTable	1.3.6.1.4.1.3052.1.4.2		not-accessible	port setup table, serial params, collect data, etc.
portSetupEntry	1.3.6.1.4.1.3052.1.4.2.1		not-accessible	port setup table, serial params, collect data, etc.
INT portIndex	1.3.6.1.4.1.3052.1.4.2.1.1	INTEGER	read-only	index for table
INT portBaud	1.3.6.1.4.1.3052.1.4.2.1.2	INTEGER	read-write	baud rate, 19200, 9600, etc.
INT portWord	1.3.6.1.4.1.3052.1.4.2.1.3	INTEGER	read-write	word length, must be 7 or 8
STR portParity	1.3.6.1.4.1.3052.1.4.2.1.4	DisplayString	read-write	a single-char string with values of N E or O
INT portStopbits	1.3.6.1.4.1.3052.1.4.2.1.5	INTEGER	read-write	number of stop bits, must be 1
INT portDataStore	1.3.6.1.4.1.3052.1.4.2.1.6	INTEGER	read-write	0 data is not stored, 1 data is stored from this port
INT portBinaryMode	1.3.6.1.4.1.3052.1.4.2.1.7	INTEGER	read-write	0 data is ASCII, 1 data is binary
INT portWrapMode	1.3.6.1.4.1.3052.1.4.2.1.8	INTEGER	read-write	0 oldest data not overwritten, 1 older data is overwritten
INT portHskMode	1.3.6.1.4.1.3052.1.4.2.1.9	INTEGER	read-write	HSK mode to use when buffer close to full, 0 none, 1 xon, 2 DTR, 3 DTR and Xon
INT portDateTimeStampMode	1.3.6.1.4.1.3052.1.4.2.1.10	INTEGER	read-write	Date/time stamp mode to use,bit mapped bit 0 - do date stamp bit 1 - include year bit 2 - include year 19xx or 20xx bit 3 - include day of week bit 4 - space after date bit 5 - include time bit 6 - include seconds bit 7 - space after time
INT portPTMode	1.3.6.1.4.1.3052.1.4.2.1.11	INTEGER	read-write	pass-through access mode. 0=none, 1=by modem, 2=by network any write kills the passthrough connection. any write requires private community name
INT portPTTime	1.3.6.1.4.1.3052.1.4.2.1.12	INTEGER	read-only	pass-through access mode time of this connection, in seconds
INT portStoreFile	1.3.6.1.4.1.3052.1.4.2.1.13	INTEGER	read-write	selects which data file data from this port is stored into
INT portPtStripOutputLfs	1.3.6.1.4.1.3052.1.4.2.1.14	INTEGER	read-write	0/1 no/yes in pass-through, strip LFs going to device on this port
INT portPtStripInputLfs	1.3.6.1.4.1.3052.1.4.2.1.15	INTEGER	read-write	0/1 no/yes in pass-through, strip LFs coming from device on this port
INT portlowDTR	1.3.6.1.4.1.3052.1.4.2.1.16	INTEGER	read-write	0/1 no/yes set DTR low and only raise it on SysAdmin & bypass connections
time	1.3.6.1.4.1.3052.1.5
STR currenttime	1.3.6.1.4.1.3052.1.5.1	DisplayString	read-write	Text string for date and time: SUN 01/02/98 12:34:27
INT autoDstAdjust	1.3.6.1.4.1.3052.1.5.2	INTEGER	read-write	0 no adjust, 1 adjust
snmpsetup	1.3.6.1.4.1.3052.1.6
INT snmpTrapsEnabled	1.3.6.1.4.1.3052.1.6.1	INTEGER	read-write	0 do not send any traps, 1 do send traps
snmpManagerTable	1.3.6.1.4.1.3052.1.6.2		not-accessible	management station names and addresses
snmpTableEntry	1.3.6.1.4.1.3052.1.6.2.1		not-accessible	entry for snmp table
INT snmpMgrIndex	1.3.6.1.4.1.3052.1.6.2.1.1	INTEGER	read-only	index for table
IP snmpManagerIp	1.3.6.1.4.1.3052.1.6.2.1.2	IpAddress	read-write	the ip address of a manager
STR snmpManagerName	1.3.6.1.4.1.3052.1.6.2.1.3	DisplayString	read-write	the name of a manager, up to 80 chars
INT snmpTrapsAutoRepeatTime	1.3.6.1.4.1.3052.1.6.3	INTEGER	read-write	0 do not repeat, else number of minutes to repeat
INT snmpSendTestTrap	1.3.6.1.4.1.3052.1.6.4	INTEGER	read-write	0 on read, any Set sends test trap to all managers in table
passwords	1.3.6.1.4.1.3052.1.7
INT modemPasswords	1.3.6.1.4.1.3052.1.7.1	INTEGER	read-write	0 no modem passwords required, 1 modem passwords are required write requires private community name
INT tcpPasswords	1.3.6.1.4.1.3052.1.7.2	INTEGER	read-write	0 no telnet/tcp passwords required, 1 passwords are required write requires private community name
INT ftpPasswords	1.3.6.1.4.1.3052.1.7.3	INTEGER	read-write	0 no ftp passwords required, 1 passwords are required write requires private community name
INT promptPasswords	1.3.6.1.4.1.3052.1.7.4	INTEGER	read-write	0 no Password: prompt, 1 -> show Password: prompt
commandPassword	1.3.6.1.4.1.3052.1.7.5
INT commandNeedsPassword	1.3.6.1.4.1.3052.1.7.5.1	INTEGER	read-write	0 not needed, 1 is needed write requires private community name
INT commandPasswordTimeout	1.3.6.1.4.1.3052.1.7.5.2	INTEGER	read-write	1-99, number of minutes of no activity which auto logs user out
passwordTable	1.3.6.1.4.1.3052.1.7.6		not-accessible	Table of password entries, r-w only with private comm. name
passwordTableEntry	1.3.6.1.4.1.3052.1.7.6.1		not-accessible	entry to password table
INT passwordIndex	1.3.6.1.4.1.3052.1.7.6.1.1	INTEGER	read-only	index to password table
STR passwordCommand	1.3.6.1.4.1.3052.1.7.6.1.2	DisplayString	read-write	password for command access
STR passwordAccess	1.3.6.1.4.1.3052.1.7.6.1.3	DisplayString	read-write	password for pass-through access
ftpsetup	1.3.6.1.4.1.3052.1.8
INT ftpAutoDelete	1.3.6.1.4.1.3052.1.8.1	INTEGER	read-write	0 files not autodeleted, 1 deleted on reading
INT ftpDataMode	1.3.6.1.4.1.3052.1.8.2	INTEGER	read-write	0 normal, 1 compression mode 1, etc.
ftpPush	1.3.6.1.4.1.3052.1.8.3
INT ftpPushEnabled	1.3.6.1.4.1.3052.1.8.3.1	INTEGER	read-write	0-no, 1-yes, enables ftp data push
INT ftpPushTiming	1.3.6.1.4.1.3052.1.8.3.2	INTEGER	read-write	how often data is pushed, 2-255 minutes
INT ftpPushTimer	1.3.6.1.4.1.3052.1.8.3.3	INTEGER	read-write	timer which counts to ftpPushTiming
IP ftpPushIPAddress	1.3.6.1.4.1.3052.1.8.3.4	IpAddress	read-write	ip address of ftp server to which we push the data
STR ftpPushUser	1.3.6.1.4.1.3052.1.8.3.5	DisplayString	read-write	text string to send for the user id
STR ftpPushPass	1.3.6.1.4.1.3052.1.8.3.6	DisplayString	read-write	text string to send for the ftp server password
STR ftpPushAcct	1.3.6.1.4.1.3052.1.8.3.7	DisplayString	read-write	text string to send for the account, if used
STR ftpPushDir	1.3.6.1.4.1.3052.1.8.3.8	DisplayString	read-write	text string to send for the directory we CWD to
ftppushTable	1.3.6.1.4.1.3052.1.8.3.9		not-accessible	Table of ftp push enables
ftppushTableEntry	1.3.6.1.4.1.3052.1.8.3.9.1		not-accessible	entry to ftp push table
INT ftppushIndex	1.3.6.1.4.1.3052.1.8.3.9.1.1	INTEGER	read-only	index to ftp push table
INT ftppushEnable	1.3.6.1.4.1.3052.1.8.3.9.1.2	INTEGER	read-write	enable for ftp push, indexed by file
INT ftpPushAlarms	1.3.6.1.4.1.3052.1.8.3.10	INTEGER	read-write	0-no, 1-yes, do we push the ALARMS file
INT ftpPushCount	1.3.6.1.4.1.3052.1.8.3.11	INTEGER	read-only	number of ftp data pushes tried since reboot
INT ftpPushStatusMode	1.3.6.1.4.1.3052.1.8.3.12	INTEGER	read-write	0-none, 1-append, 2-replace, status file modes
STR ftpPushServerName	1.3.6.1.4.1.3052.1.8.3.13	DisplayString	read-write	Name of the FTP Push Targer Server
databases	1.3.6.1.4.1.3052.1.9
entireDatabase	1.3.6.1.4.1.3052.1.9.1
databaseStatus	1.3.6.1.4.1.3052.1.9.1.1
INT databasePfull	1.3.6.1.4.1.3052.1.9.1.1.1	INTEGER	read-only	percentage full of all database
INT databaseSize	1.3.6.1.4.1.3052.1.9.1.1.2	INTEGER	read-only	Size of Data Storage Area, in bytes
INT databaseRecordsAvailable	1.3.6.1.4.1.3052.1.9.1.1.3	INTEGER	read-only	Records which are available to read, total in all files
INT databaseRecordsDeleted	1.3.6.1.4.1.3052.1.9.1.1.4	INTEGER	read-only	Records which are deleted, total in all files
databaseAlarmTable	1.3.6.1.4.1.3052.1.9.1.2		not-accessible	table for levels 1 2 3 of all database alarms and actions
databaseAlarmEntry	1.3.6.1.4.1.3052.1.9.1.2.1		not-accessible	entry for database alarm config and actions table
INT databaseAlarmIndex	1.3.6.1.4.1.3052.1.9.1.2.1.1	INTEGER	read-only	Index for table, 1 2 or 3
INT databaseAlarmActive	1.3.6.1.4.1.3052.1.9.1.2.1.2	INTEGER	read-write	0/1, 1 = active
INT databaseAlarmThreshold	1.3.6.1.4.1.3052.1.9.1.2.1.3	INTEGER	read-write	1-99, percentage full threshold level
INT databaseAlarmBeeperActions	1.3.6.1.4.1.3052.1.9.1.2.1.4	INTEGER	read-write	0 1 2, -> none, 1/10 or 10/10
INT databaseAlarmSerialActions	1.3.6.1.4.1.3052.1.9.1.2.1.5	INTEGER	read-write	bits 0-7 show which messages 1-8 are sent
INT databaseAlarmPagerActions	1.3.6.1.4.1.3052.1.9.1.2.1.6	INTEGER	read-write	bits 0-7 show which pagers 1-8 are used
INT databaseAlarmCalloutActions	1.3.6.1.4.1.3052.1.9.1.2.1.7	INTEGER	read-write	bits 0-7 show which modem callouts 1-8 are used
INT databaseAlarmTrapActions	1.3.6.1.4.1.3052.1.9.1.2.1.8	INTEGER	read-write	0/1 for traps are sent or not
INT databaseAlarmFileStore	1.3.6.1.4.1.3052.1.9.1.3	INTEGER	read-write	0-no, 1-yes, store alarms in the ALARMS file
INT databaseAlarmFileMaxSize	1.3.6.1.4.1.3052.1.9.1.4	INTEGER	read-write	in K, max size for alarms file 4-32k
databaseFiles	1.3.6.1.4.1.3052.1.9.2
filesetup	1.3.6.1.4.1.3052.1.9.2.1
INT charmaskEnabled	1.3.6.1.4.1.3052.1.9.2.1.1	INTEGER	read-write	0/1 char masking enabled
STR charmask	1.3.6.1.4.1.3052.1.9.2.1.2	DisplayString	read-write	32-byte hex ascii for character masking
INT maxRecordChars	1.3.6.1.4.1.3052.1.9.2.1.3	INTEGER	read-write	max characters in an ASCII record
INT binRecordBlocking	1.3.6.1.4.1.3052.1.9.2.1.4	INTEGER	read-write	# chars max to block binary records into
INT recordCollectionTimeout	1.3.6.1.4.1.3052.1.9.2.1.5	INTEGER	read-write	# seconds to allow before terminating a record automatically
fileTable	1.3.6.1.4.1.3052.1.9.2.2		not-accessible	table of directory entries
fileTableEntry	1.3.6.1.4.1.3052.1.9.2.2.1		not-accessible	entry for table
INT fileTableIndex	1.3.6.1.4.1.3052.1.9.2.2.1.1	INTEGER	read-only	index for the table
STR fileName	1.3.6.1.4.1.3052.1.9.2.2.1.2	DisplayString	read-only	name of the file
STR fileType	1.3.6.1.4.1.3052.1.9.2.2.1.3	DisplayString	read-write	type of data, up to 24 chars
INT fileSize	1.3.6.1.4.1.3052.1.9.2.2.1.4	INTEGER	read-only	file size in bytes
INT fileRecords	1.3.6.1.4.1.3052.1.9.2.2.1.5	INTEGER	read-only	file size in records
INT fileRecordsAvailable	1.3.6.1.4.1.3052.1.9.2.2.1.6	INTEGER	read-only	# recs available
INT fileRecordsDeleted	1.3.6.1.4.1.3052.1.9.2.2.1.7	INTEGER	read-only	# recs deleted
INT filePercentNow	1.3.6.1.4.1.3052.1.9.2.2.1.8	INTEGER	read-only	% of all of memory this file is, right now
fileAlarms	1.3.6.1.4.1.3052.1.9.2.3		not-accessible	file alarms, indexed by file and threshold
fileAlarmEntry	1.3.6.1.4.1.3052.1.9.2.3.1		not-accessible	entry to the table
INT fileAlarmFileIndex	1.3.6.1.4.1.3052.1.9.2.3.1.1	INTEGER	read-only	index for filenumber
INT fileAlarmThresholdIndex	1.3.6.1.4.1.3052.1.9.2.3.1.2	INTEGER	read-only	index for filenumber threshold
INT fileAlarmActive	1.3.6.1.4.1.3052.1.9.2.3.1.3	INTEGER	read-write	0/1 this file alarm active
INT fileAlarmThreshold	1.3.6.1.4.1.3052.1.9.2.3.1.4	INTEGER	read-write	1-99, threshold level
INT fileAlarmBeeperActions	1.3.6.1.4.1.3052.1.9.2.3.1.5	INTEGER	read-write	0 1 2, none, 1/10 or 10/10
INT fileAlarmSerialActions	1.3.6.1.4.1.3052.1.9.2.3.1.6	INTEGER	read-write	bits 0-7 show which messages 1-8 are sent
INT fileAlarmPagerActions	1.3.6.1.4.1.3052.1.9.2.3.1.7	INTEGER	read-write	bits 0-7 show which pagers 1-8 are used
INT fileAlarmCalloutActions	1.3.6.1.4.1.3052.1.9.2.3.1.8	INTEGER	read-write	bits 0-7 show which modem callouts 1-8 are used
INT fileAlarmTrapActions	1.3.6.1.4.1.3052.1.9.2.3.1.9	INTEGER	read-write	0/1 for traps are sent or not
alarms	1.3.6.1.4.1.3052.1.10
dataAlarmTable	1.3.6.1.4.1.3052.1.10.1		not-accessible	table of read-only items for data alarm setup
dataAlarmEntry	1.3.6.1.4.1.3052.1.10.1.1		not-accessible	Data alarm table entry
INT dataAlarmIndex	1.3.6.1.4.1.3052.1.10.1.1.1	INTEGER	read-only	index for data alarms
INT dataAlarmActive	1.3.6.1.4.1.3052.1.10.1.1.2	INTEGER	read-only	0/1 active
STR dataAlarmName	1.3.6.1.4.1.3052.1.10.1.1.3	DisplayString	read-only	name of alarm
INT dataAlarmCounter	1.3.6.1.4.1.3052.1.10.1.1.4	INTEGER	read-only	counter for this alarm
INT dataAlarmThreshold	1.3.6.1.4.1.3052.1.10.1.1.5	INTEGER	read-only	threshold for this alarm
INT dataAlarmClearMode	1.3.6.1.4.1.3052.1.10.1.1.6	INTEGER	read-only	code for clearing mode
STR dataAlarmClearTime	1.3.6.1.4.1.3052.1.10.1.1.7	DisplayString	read-only	time of day, e.g., 01:20
INT dataAlarmAcked	1.3.6.1.4.1.3052.1.10.1.1.8	INTEGER	read-write	0 on read, any set to ack this alarm
INT dataAlarmBeeperActions	1.3.6.1.4.1.3052.1.10.1.1.9	INTEGER	read-only	0 1 2, none, 1/10 or 10/10
INT dataAlarmSerialActions	1.3.6.1.4.1.3052.1.10.1.1.10	INTEGER	read-only	bits 0-7 show which messages 1-8 are sent
INT dataAlarmPagerActions	1.3.6.1.4.1.3052.1.10.1.1.11	INTEGER	read-only	bits 0-7 show which pagers 1-8 are used
INT dataAlarmCalloutActions	1.3.6.1.4.1.3052.1.10.1.1.12	INTEGER	read-only	bits 0-7 show which modem callouts 1-8 are used
INT dataAlarmTrapActions	1.3.6.1.4.1.3052.1.10.1.1.13	INTEGER	read-only	0/1 for traps are sent or not
STR dataAlarmString	1.3.6.1.4.1.3052.1.10.1.1.14	DisplayString	read-only	last data alarm string for this alarm
INT dataAlarmPort	1.3.6.1.4.1.3052.1.10.1.1.15	INTEGER	read-only	port number for last data alarm string for this alarm
INT dataAlarmAutoClear	1.3.6.1.4.1.3052.1.10.1.1.16	INTEGER	read-only	0/1 disabled/enabled to auto clear counter when it reached threshold
sensorAlarmTable	1.3.6.1.4.1.3052.1.10.2		not-accessible	table of read-only items for sensor alarm setup
sensorAlarmEntry	1.3.6.1.4.1.3052.1.10.2.1		not-accessible	sensor alarm table entry
INT sensorAlarmIndex	1.3.6.1.4.1.3052.1.10.2.1.1	INTEGER	read-only	index for sensor alarms
INT sensorAlarmActive	1.3.6.1.4.1.3052.1.10.2.1.2	INTEGER	read-write	0/1 active
STR sensorAlarmName	1.3.6.1.4.1.3052.1.10.2.1.3	DisplayString	read-write	name of alarm
INT sensorAlarmMode	1.3.6.1.4.1.3052.1.10.2.1.4	INTEGER	read-write	0 - open active, 1 - closed active
INT sensorAlarmCounter	1.3.6.1.4.1.3052.1.10.2.1.5	INTEGER	read-write	counter for this alarm
INT sensorAlarmThreshold	1.3.6.1.4.1.3052.1.10.2.1.6	INTEGER	read-write	threshold for this alarm
INT sensorAlarmAcked	1.3.6.1.4.1.3052.1.10.2.1.7	INTEGER	read-write	0 on read, any set to ack this alarm
INT sensorAlarmBeeperActions	1.3.6.1.4.1.3052.1.10.2.1.8	INTEGER	read-write	0 1 2, none, 1/10 or 10/10
INT sensorAlarmSerialActions	1.3.6.1.4.1.3052.1.10.2.1.9	INTEGER	read-write	bits 0-7 show which messages 1-8 are sent
INT sensorAlarmPagerActions	1.3.6.1.4.1.3052.1.10.2.1.10	INTEGER	read-write	bits 0-7 show which pagers 1-8 are used
INT sensorAlarmCalloutActions	1.3.6.1.4.1.3052.1.10.2.1.11	INTEGER	read-write	bits 0-7 show which modem callouts 1-8 are used
INT sensorAlarmTrapActions	1.3.6.1.4.1.3052.1.10.2.1.12	INTEGER	read-write	0/1 for traps are sent or not
INT sensorAlarmState	1.3.6.1.4.1.3052.1.10.2.1.13	INTEGER	read-only	0-> open 1-> closed for current state
nodataAlarms	1.3.6.1.4.1.3052.1.10.3
nodataAlarmStatus	1.3.6.1.4.1.3052.1.10.3.1		not-accessible	no data status table
nodataAlarmStatusEntry	1.3.6.1.4.1.3052.1.10.3.1.1		not-accessible	status table entry
INT nodataAlarmStatusIndex	1.3.6.1.4.1.3052.1.10.3.1.1.1	INTEGER	read-only	index for table
INT nodataAlarmStatusCounter	1.3.6.1.4.1.3052.1.10.3.1.1.2	INTEGER	read-write	the nodata counter
INT nodataAlarmStatusAcked	1.3.6.1.4.1.3052.1.10.3.1.1.3	INTEGER	read-write	reads as 0, any write acks this alarm
nodataTable	1.3.6.1.4.1.3052.1.10.3.2		not-accessible	nodata table
nodataTableEntry	1.3.6.1.4.1.3052.1.10.3.2.1		not-accessible	nodata defn. table entry
INT nodataTablePortIndex	1.3.6.1.4.1.3052.1.10.3.2.1.1	INTEGER	not-accessible	index by port
INT nodataTableScheduleIndex	1.3.6.1.4.1.3052.1.10.3.2.1.2	INTEGER	not-accessible	index by schedule
INT nodataTableLevelIndex	1.3.6.1.4.1.3052.1.10.3.2.1.3	INTEGER	not-accessible	index by level
INT nodataTableActive	1.3.6.1.4.1.3052.1.10.3.2.1.4	INTEGER	read-write	0/1 , enabled or not
STR nodataTableSchedule	1.3.6.1.4.1.3052.1.10.3.2.1.5	DisplayString	read-write	schedule, format is hh:mm-hh:mm
INT nodataTableThreshold	1.3.6.1.4.1.3052.1.10.3.2.1.6	INTEGER	read-write	#minutes for no data for alarm
INT nodataTableBeeperActions	1.3.6.1.4.1.3052.1.10.3.2.1.7	INTEGER	read-write	0 1 2, none, 1/10 or 10/10
INT nodataTableSerialActions	1.3.6.1.4.1.3052.1.10.3.2.1.8	INTEGER	read-write	bits 0-7 show which messages 1-8 are sent
INT nodataTablePagerActions	1.3.6.1.4.1.3052.1.10.3.2.1.9	INTEGER	read-write	bits 0-7 show which pagers 1-8 are used
INT nodataTableCalloutActions	1.3.6.1.4.1.3052.1.10.3.2.1.10	INTEGER	read-write	bits 0-7 show which modem callouts 1-8 are used
INT nodataTableTrapActions	1.3.6.1.4.1.3052.1.10.3.2.1.11	INTEGER	read-write	0/1 for traps are sent or not
nodataAlarmHolidays	1.3.6.1.4.1.3052.1.10.3.3
INT nodataNumberHolidays	1.3.6.1.4.1.3052.1.10.3.3.1	INTEGER	read-only	number of nodata holidays defined
nodataHolidayTable	1.3.6.1.4.1.3052.1.10.3.3.2		not-accessible	holiday table
nodataHolidayTableEntry	1.3.6.1.4.1.3052.1.10.3.3.2.1		not-accessible	holiday table entry
INT nodataHolidayIndex	1.3.6.1.4.1.3052.1.10.3.3.2.1.1	INTEGER	read-only	index for holiday list
STR nodataHolidayItem	1.3.6.1.4.1.3052.1.10.3.3.2.1.2	DisplayString	read-only	holiday list item, format is mm/dd
STR nodataHolidayAdd	1.3.6.1.4.1.3052.1.10.3.3.3	DisplayString	read-write	null on read, set with holiday to add MM/DD
STR nodataHolidayDelete	1.3.6.1.4.1.3052.1.10.3.3.4	DisplayString	read-write	null on read, set with holiday to delete MM/DD
INT nodataHolidayClear	1.3.6.1.4.1.3052.1.10.3.3.5	INTEGER	read-write	read returns 0, write requires private community name. used to clear the holiday list
scheduleAlarmTable	1.3.6.1.4.1.3052.1.10.4		not-accessible	scheduled alarm table
scheduleAlarmEntry	1.3.6.1.4.1.3052.1.10.4.1		not-accessible	schedule table entry
INT scheduleIndex	1.3.6.1.4.1.3052.1.10.4.1.1	INTEGER	read-only	day index
INT scheduleActive	1.3.6.1.4.1.3052.1.10.4.1.2	INTEGER	read-write	if active or not
STR scheduleTime	1.3.6.1.4.1.3052.1.10.4.1.3	DisplayString	read-write	time of day format is: hh:mm
INT scheduleAcked	1.3.6.1.4.1.3052.1.10.4.1.4	INTEGER	read-write	reads 0, any set acks alarm
INT scheduleBeeperActions	1.3.6.1.4.1.3052.1.10.4.1.5	INTEGER	read-write	0 1 2, none, 1/10 or 10/10
INT scheduleSerialActions	1.3.6.1.4.1.3052.1.10.4.1.6	INTEGER	read-write	bits 0-7 show which messages 1-8 are sent
INT schedulePagerActions	1.3.6.1.4.1.3052.1.10.4.1.7	INTEGER	read-write	bits 0-7 show which pagers 1-8 are used
INT scheduleCalloutActions	1.3.6.1.4.1.3052.1.10.4.1.8	INTEGER	read-write	bits 0-7 show which modem callouts 1-8 are used
INT scheduleTrapActions	1.3.6.1.4.1.3052.1.10.4.1.9	INTEGER	read-write	0/1 for traps are sent or not
actions	1.3.6.1.4.1.3052.1.11
actionsBuzzer	1.3.6.1.4.1.3052.1.11.1
INT actionsBuzzerState	1.3.6.1.4.1.3052.1.11.1.1	INTEGER	read-only	current buzzer state 0.1.2
actionsSerialTable	1.3.6.1.4.1.3052.1.11.2		not-accessible	serial message table
actionsSerialTableEntry	1.3.6.1.4.1.3052.1.11.2.1		not-accessible	serial table entry
INT serialTableIndex	1.3.6.1.4.1.3052.1.11.2.1.1	INTEGER	read-only	serial table index
STR serialTableMessage	1.3.6.1.4.1.3052.1.11.2.1.2	DisplayString	read-write	serial table string
actionsPagerTable	1.3.6.1.4.1.3052.1.11.3		not-accessible	pager table
actionsPagerTableEntry	1.3.6.1.4.1.3052.1.11.3.1		not-accessible	pager table entry
INT pagerTableIndex	1.3.6.1.4.1.3052.1.11.3.1.1	INTEGER	read-only	table index
INT pagerType	1.3.6.1.4.1.3052.1.11.3.1.2	INTEGER	read-write	0-numeric, 1-alpha
STR pagerPhonenumber	1.3.6.1.4.1.3052.1.11.3.1.3	DisplayString	read-write	phone number to call for pager
STR pagerID	1.3.6.1.4.1.3052.1.11.3.1.4	DisplayString	read-write	ID or 2nd number to dial
INT pagerDialDelay	1.3.6.1.4.1.3052.1.11.3.1.5	INTEGER	read-write	# seconds on numeric to delay between dial and send pagerID or message
INT pagerHangupDelay	1.3.6.1.4.1.3052.1.11.3.1.6	INTEGER	read-write	# seconds on numeric to delay between messages and before hangup
STR pagerMessage	1.3.6.1.4.1.3052.1.11.3.1.7	DisplayString	read-write	message, either alpha or numeric
INT pagerSendId	1.3.6.1.4.1.3052.1.11.3.1.8	INTEGER	read-write	0/1 send unit ID or not to pager
INT pagerSendReason	1.3.6.1.4.1.3052.1.11.3.1.9	INTEGER	read-write	0/1 send reason for page or not to pager
INT pagerMaxAttempts	1.3.6.1.4.1.3052.1.11.3.1.10	INTEGER	read-write	max tries to be successful
INT pagerAttempts	1.3.6.1.4.1.3052.1.11.3.1.11	INTEGER	read-write	current number of tries
INT pagerAttemptDelay	1.3.6.1.4.1.3052.1.11.3.1.12	INTEGER	read-write	# minutes between attempts
INT pagerRepeat	1.3.6.1.4.1.3052.1.11.3.1.13	INTEGER	read-write	0/1 do we repeat successful
INT pagerRepeatDelay	1.3.6.1.4.1.3052.1.11.3.1.14	INTEGER	read-write	# minutes between repeats, if used
actionsCalloutTable	1.3.6.1.4.1.3052.1.11.4		not-accessible	callout table
actionsCalloutTableEntry	1.3.6.1.4.1.3052.1.11.4.1		not-accessible	callout table entry
INT calloutTableIndex	1.3.6.1.4.1.3052.1.11.4.1.1	INTEGER	read-only	table index
STR calloutPhonenumber	1.3.6.1.4.1.3052.1.11.4.1.2	DisplayString	read-write	phone number to call for callout
INT calloutMaxConnecttime	1.3.6.1.4.1.3052.1.11.4.1.3	INTEGER	read-write	# seconds to wait for carrier
STR calloutMessage	1.3.6.1.4.1.3052.1.11.4.1.4	DisplayString	read-write	message to send
INT calloutSendId	1.3.6.1.4.1.3052.1.11.4.1.5	INTEGER	read-write	0/1 send unit ID or not to callout
INT calloutSendReason	1.3.6.1.4.1.3052.1.11.4.1.6	INTEGER	read-write	0/1 send reason for page or not to callout
INT calloutCommandWait	1.3.6.1.4.1.3052.1.11.4.1.7	INTEGER	read-write	#seconds to wait for a command on a callout before hangup
INT calloutMaxAttempts	1.3.6.1.4.1.3052.1.11.4.1.8	INTEGER	read-write	max tries to be successful
INT calloutAttempts	1.3.6.1.4.1.3052.1.11.4.1.9	INTEGER	read-write	current number of tries
INT calloutAttemptDelay	1.3.6.1.4.1.3052.1.11.4.1.10	INTEGER	read-write	# minutes between attempts
INT calloutRepeat	1.3.6.1.4.1.3052.1.11.4.1.11	INTEGER	read-write	0/1 do we repeat successful
INT calloutRepeatDelay	1.3.6.1.4.1.3052.1.11.4.1.12	INTEGER	read-write	# minutes between repeats, if used
actionsTraps	1.3.6.1.4.1.3052.1.11.5
INT actionsTrapsEntSpecific	1.3.6.1.4.1.3052.1.11.5.1	INTEGER	read-write	0/1 enterprise specific traps enabled
INT actionsTrapsEntSpecCount	1.3.6.1.4.1.3052.1.11.5.2	INTEGER	read-only	number of enterprise specific traps sent since last re-boot
controls	1.3.6.1.4.1.3052.1.12
opSettings	1.3.6.1.4.1.3052.1.12.1
INT linefeeds	1.3.6.1.4.1.3052.1.12.1.1	INTEGER	read-write	0/1 are linefeeds added to CRs on command responses?
INT duplex	1.3.6.1.4.1.3052.1.12.1.2	INTEGER	read-write	0-half 1-full
INT response	1.3.6.1.4.1.3052.1.12.1.3	INTEGER	read-write	0-codes 1-words
INT datafilterEnabled	1.3.6.1.4.1.3052.1.12.1.4	INTEGER	read-write	0/1 off/on
INT alarmfilterEnabled	1.3.6.1.4.1.3052.1.12.1.5	INTEGER	read-write	0/1 off/on
auxportMode	1.3.6.1.4.1.3052.1.12.1.6
INT operatingMode	1.3.6.1.4.1.3052.1.12.1.6.1	INTEGER	read-write	1 command 2 input/access 3 unused 4 inline 5 extmodem
INT inlineMode	1.3.6.1.4.1.3052.1.12.1.6.2	INTEGER	read-write	1,2,3 if inline, mode 1 (N->2) mode 2 (1->2, 3->4) mode 3 (1->2, 3->4, 5->6)
INT inlineSource	1.3.6.1.4.1.3052.1.12.1.6.3	INTEGER	read-write	if inline and inlineMode==1, source of I/O2 inline
inlineHskMode	1.3.6.1.4.1.3052.1.12.1.6.4
INT inlineHsk2	1.3.6.1.4.1.3052.1.12.1.6.4.1	INTEGER	read-write	handshake mode 0-3 for inline port I/O 2
INT inlineHsk4	1.3.6.1.4.1.3052.1.12.1.6.4.2	INTEGER	read-write	handshake mode 0-3 for inline port I/O 4
INT inlineHsk6	1.3.6.1.4.1.3052.1.12.1.6.4.3	INTEGER	read-write	handshake mode 0-3 for inline port I/O 6
INT sureEnabled	1.3.6.1.4.1.3052.1.12.1.7	INTEGER	read-write	0/1 off/on
INT commandTcpipTimeout	1.3.6.1.4.1.3052.1.12.1.8	INTEGER	read-write	0-none, else number of no-activity minutes -> tcpip command to drop
INT sysadminTcpipTimeout	1.3.6.1.4.1.3052.1.12.1.9	INTEGER	read-write	0-none, else number of no-activity minutes -> tcpip sysadmin to drop
INT bypassEndchar	1.3.6.1.4.1.3052.1.12.1.10	INTEGER	read-write	ascii value for character to exit bypass mode. default ->27
INT routerAutoPing	1.3.6.1.4.1.3052.1.12.1.11	INTEGER	read-write	0/1 = no/yes, default is 0, do we ping the default router every 10 minutes?
modemSettings	1.3.6.1.4.1.3052.1.12.2
INT modemParity	1.3.6.1.4.1.3052.1.12.2.1	INTEGER	read-write	1 7E 2 7O 3 8N
STR modemUserSetup	1.3.6.1.4.1.3052.1.12.2.2	DisplayString	read-write	sent to modem on init before the factory setup string
STR modemTapSetup	1.3.6.1.4.1.3052.1.12.2.3	DisplayString	read-write	sent to modem on just before doing TAP (alpha pager) protocol
STR modemAnswerString	1.3.6.1.4.1.3052.1.12.2.4	DisplayString	read-write	sent when modem makes connection
STR modemExtSetup	1.3.6.1.4.1.3052.1.12.2.5	DisplayString	read-write	sent to ext. modem for setup string
INT modemExtSetupTime	1.3.6.1.4.1.3052.1.12.2.6	INTEGER	read-write	# minutes of idle time between sending ext. modem setup string
INT modemInactivityTimer	1.3.6.1.4.1.3052.1.12.2.7	INTEGER	read-write	# minutes of no transmit which aborts a connection
STR modemAutoexecString	1.3.6.1.4.1.3052.1.12.2.8	DisplayString	read-write	command string which auto-executes after modem connection if no other command within 10 seconds
INT modemAutoexecEnabled	1.3.6.1.4.1.3052.1.12.2.9	INTEGER	read-write	0/1 autoexec enabled
INT modemTimeBetweenOutbound	1.3.6.1.4.1.3052.1.12.2.10	INTEGER	read-write	# seconds (minimum) between outbound call attempts
dataRelease	1.3.6.1.4.1.3052.1.12.3
INT releaseMode	1.3.6.1.4.1.3052.1.12.3.1	INTEGER	read-write	1-Line 3-CBB 4-Xmodem
INT autodeleteEnable	1.3.6.1.4.1.3052.1.12.3.2	INTEGER	read-write	1/2 off/on autodelete for CBB and Xmodem
INT releaseCompressed	1.3.6.1.4.1.3052.1.12.3.3	INTEGER	read-write	1-compressed 2-decompressed
otherControls	1.3.6.1.4.1.3052.1.12.4
INT waitMode	1.3.6.1.4.1.3052.1.12.4.1	INTEGER	read-write	1/2 off/on wait for 02 after 01 on rlmodes
INT tagMode	1.3.6.1.4.1.3052.1.12.4.2	INTEGER	read-write	1/2 off/on Line/Block tag enabled
INT crcMode	1.3.6.1.4.1.3052.1.12.4.3	INTEGER	read-write	1/2 off/on add CRC to ascii releases
INT dleMode	1.3.6.1.4.1.3052.1.12.4.4	INTEGER	read-write	1/2 off/on use DLE stuffing on CBB
INT cbbRetransmits	1.3.6.1.4.1.3052.1.12.4.5	INTEGER	read-write	# times a block retransmitted in CBB mode
INT cbbTimeout	1.3.6.1.4.1.3052.1.12.4.6	INTEGER	read-write	# seconds to wait for an ack before retransmit in CBB mode
INT activeDatabase	1.3.6.1.4.1.3052.1.12.5	INTEGER	read-write	selects a file. ports 2001-2006 auto select this variable
alarmhistory	1.3.6.1.4.1.3052.1.13
actionQueue	1.3.6.1.4.1.3052.1.13.1
INT actionCount	1.3.6.1.4.1.3052.1.13.1.1	INTEGER	read-only	number of active items in action table, 0-nn
actionTable	1.3.6.1.4.1.3052.1.13.1.2		not-accessible	action queue table
actionTableEntry	1.3.6.1.4.1.3052.1.13.1.2.1		not-accessible	action queue entry
INT actionTableIndex	1.3.6.1.4.1.3052.1.13.1.2.1.1	INTEGER	read-only	action table entry
INT actionAcked	1.3.6.1.4.1.3052.1.13.1.2.1.2	INTEGER	read-write	reads 0, any set removes (acks) this action
INT actionReason	1.3.6.1.4.1.3052.1.13.1.2.1.3	INTEGER	read-only	code reason for action
INT actionReasonID	1.3.6.1.4.1.3052.1.13.1.2.1.4	INTEGER	read-only	which of the (reasons) e.g, alarm 3 vs. alarm 4
INT actionReasonLevel	1.3.6.1.4.1.3052.1.13.1.2.1.5	INTEGER	read-only	which of the levels for alarms which have 1-3 levels
INT actionType	1.3.6.1.4.1.3052.1.13.1.2.1.6	INTEGER	read-only	type of action being taken (page, callout, etc.)
INT actionTypeID	1.3.6.1.4.1.3052.1.13.1.2.1.7	INTEGER	read-only	which of the actions e.g, pager 3 vs. pager 4
INT actionRepeatTime	1.3.6.1.4.1.3052.1.13.1.2.1.8	INTEGER	read-only	#minutes between repeats of attempts of this action
INT actionAttempts	1.3.6.1.4.1.3052.1.13.1.2.1.9	INTEGER	read-only	# of attempts to try this action so far
INT actionNextAttempt	1.3.6.1.4.1.3052.1.13.1.2.1.10	INTEGER	read-only	# minutes until the next attempt of this action
STR actionTimeStamp	1.3.6.1.4.1.3052.1.13.1.2.1.11	DisplayString	read-only	date and time string: 02/34 12:34, or text message if no items
actionHistory	1.3.6.1.4.1.3052.1.13.2
INT historyCount	1.3.6.1.4.1.3052.1.13.2.1	INTEGER	read-only	number of history items in history table, 0-nn
historyTable	1.3.6.1.4.1.3052.1.13.2.2		not-accessible	action history table
historyTableEntry	1.3.6.1.4.1.3052.1.13.2.2.1		not-accessible	history queue entry
INT historyTableIndex	1.3.6.1.4.1.3052.1.13.2.2.1.1	INTEGER	read-only	history table entry
INT historyEntryType	1.3.6.1.4.1.3052.1.13.2.2.1.2	INTEGER	read-write	type of entry (e.g., modem fail, pager pass, etc.)
INT historyReason	1.3.6.1.4.1.3052.1.13.2.2.1.3	INTEGER	read-only	code reason for history
INT historyReasonID	1.3.6.1.4.1.3052.1.13.2.2.1.4	INTEGER	read-only	which of the (reasons) e.g, alarm 3 vs. alarm 4
INT historyReasonLevel	1.3.6.1.4.1.3052.1.13.2.2.1.5	INTEGER	read-only	which of the levels for alarms which have 1-3 levels
INT historyType	1.3.6.1.4.1.3052.1.13.2.2.1.6	INTEGER	read-only	type of history being taken (page, callout, etc.)
INT historyTypeID	1.3.6.1.4.1.3052.1.13.2.2.1.7	INTEGER	read-only	which of the historys e.g, pager 3 vs. pager 4
STR historyTimeStamp	1.3.6.1.4.1.3052.1.13.2.2.1.8	DisplayString	read-only	date and time string: 02/34 12:34, or text message if no items
INT historyClearLog	1.3.6.1.4.1.3052.1.13.2.2.1.9	INTEGER	read-write	reads 0, any set clears all history log items
STR lastCalloutPageReason	1.3.6.1.4.1.3052.1.13.3	DisplayString	read-only	the reason string for the last callout or page, or NONE if never used
realtimesocket	1.3.6.1.4.1.3052.1.14
INT rtsShowAnswer	1.3.6.1.4.1.3052.1.14.1	INTEGER	read-write	0-no 1-yes, show answer string on connection (deprecated)
INT rtsNeedPassword	1.3.6.1.4.1.3052.1.14.2	INTEGER	read-only	0-no 1-yes, need password on RTS connection (deprecated)
INT rtsWaitXon	1.3.6.1.4.1.3052.1.14.3	INTEGER	read-write	0-no 1-yes, wait for Xon after connection before sending data (deprecated)
INT rtsIdleTimeout	1.3.6.1.4.1.3052.1.14.4	INTEGER	read-write	0-255, 0-none, 1-255 #idle minutes no data = shutdown socket (deprecated)
INT rtsEmptyClose	1.3.6.1.4.1.3052.1.14.5	INTEGER	read-write	0->no, 1-> yes, when file empty close socket (polling, not rt data) (deprecated)
rtsTable	1.3.6.1.4.1.3052.1.14.6		not-accessible	real time socket table
rtsTableEntry	1.3.6.1.4.1.3052.1.14.6.1		not-accessible	rts table entry
INT rtsTableIndex	1.3.6.1.4.1.3052.1.14.6.1.1	INTEGER	read-only	rts table entry index
INT rtsNoStore	1.3.6.1.4.1.3052.1.14.6.1.2	INTEGER	read-write	0-allow storage, 1-don't store data when RTS socket not connected
INT rtsDenied	1.3.6.1.4.1.3052.1.14.6.1.3	INTEGER	read-write	0-don't allow, 1=yes allow this rts socket to connect
INT rtsSocketState	1.3.6.1.4.1.3052.1.14.6.1.4	INTEGER	read-only	0-closed, 1-wait for pass, 2-wait for xon, 3=open for data
INT rtsPortShowAnswer	1.3.6.1.4.1.3052.1.14.6.1.5	INTEGER	read-write	0-no 1-yes, show answer string on connection
INT rtsPortNeedPassword	1.3.6.1.4.1.3052.1.14.6.1.6	INTEGER	read-only	0-no 1-yes, need password on RTS connection
INT rtsPortWaitXon	1.3.6.1.4.1.3052.1.14.6.1.7	INTEGER	read-write	0-no 1-yes, wait for Xon after connection before sending data
INT rtsPortIdleTimeout	1.3.6.1.4.1.3052.1.14.6.1.8	INTEGER	read-write	0-255, 0-none, 1-255 #idle minutes no data = shutdown socket
INT rtsPortEmptyClose	1.3.6.1.4.1.3052.1.14.6.1.9	INTEGER	read-write	0->no, 1-> yes, when file empty close socket (polling, not rt data)
iprestrictions	1.3.6.1.4.1.3052.1.15
iprestrictTable	1.3.6.1.4.1.3052.1.15.1		not-accessible	ip restrictions table
iprestrictTableEntry	1.3.6.1.4.1.3052.1.15.1.1		not-accessible	ip restriction table entry
INT iprestrictTableIndex	1.3.6.1.4.1.3052.1.15.1.1.1	INTEGER	read-only	ip restrict table entry index
IP iprestrictIpAddress	1.3.6.1.4.1.3052.1.15.1.1.2	IpAddress	read-only	an ip address which forces a restriction or allowance for an ip range
INT suspendIPRestrictions	1.3.6.1.4.1.3052.1.15.2	INTEGER	read-write	read returns 0, writing requires the private community name. default is 0 set to 1 to suspend IP restrictions while loading the list set back to 0 to allow the restrictions to be used.
INT killIPRestrictions	1.3.6.1.4.1.3052.1.15.3	INTEGER	read-write	read returns 0, writing requires the private community name. any set removes all entries from the IP restrcition list.
IP addIPRestrictions	1.3.6.1.4.1.3052.1.15.4	IpAddress	read-write	read returns 0, writing requires the private community name. any set adds an entry to the IP restriction list note that list is no re-sorted, so must add in order
ipsetup	1.3.6.1.4.1.3052.1.16
ipCurrent	1.3.6.1.4.1.3052.1.16.1
INT ipCurrentStatic	1.3.6.1.4.1.3052.1.16.1.1	INTEGER	read-only	1=static, 0=dynamic
IP ipCurrentAddress	1.3.6.1.4.1.3052.1.16.1.2	IpAddress	read-only	current IP address
IP ipCurrentSubnetMask	1.3.6.1.4.1.3052.1.16.1.3	IpAddress	read-only	current subnet mask
IP ipCurrentDefaultRouter	1.3.6.1.4.1.3052.1.16.1.4	IpAddress	read-only	current default router
ipNew	1.3.6.1.4.1.3052.1.16.2
INT ipNewStatic	1.3.6.1.4.1.3052.1.16.2.1	INTEGER	read-write	1=static, 0=dynamic. write requires private community name.
IP ipNewAddress	1.3.6.1.4.1.3052.1.16.2.2	IpAddress	read-write	read=current new address, write requires private community name.
IP ipNewSubnetMask	1.3.6.1.4.1.3052.1.16.2.3	IpAddress	read-write	read=current new subnet mask, write requires private community name.
IP ipNewDefaultRouter	1.3.6.1.4.1.3052.1.16.2.4	IpAddress	read-write	read=current new default router, write requires private community name.
INT ipNewSetup	1.3.6.1.4.1.3052.1.16.2.5	INTEGER	read-write	read=0. write requires private community name. any write causes the current object values for ipNewStatic, ipNewAddress, ipNewSubnetMask and ipNewDefaultRouter to be used. Causes the unit to re-initialize its network stacks with these new values. Changes to ipNewStatic, ipNewAddress, ipNewSubnetMask and ipNewDefaultRouter do not affect the network stack until ipNewSetup is written with some value:
pppsetup	1.3.6.1.4.1.3052.1.17
pppIdentification	1.3.6.1.4.1.3052.1.17.1
STR pppIDString	1.3.6.1.4.1.3052.1.17.1.1	DisplayString	read-write	sent in ppp up trap to provide host identification string
IP pppIPAddress	1.3.6.1.4.1.3052.1.17.1.2	IpAddress	read-only	sent in ppp up trap to provide host identification by IP address
ccode	1.3.6.1.4.1.3052.1.18
INT ccodeLoaded	1.3.6.1.4.1.3052.1.18.1	INTEGER	read-only	0/1, no/yes, is ccode loaded
INT ccodeRunning	1.3.6.1.4.1.3052.1.18.2	INTEGER	read-only	0/1, no/yes, is ccode running
INT ccodeStackMainWas	1.3.6.1.4.1.3052.1.18.3	INTEGER	read-only	# of bytes of stack used by main app, last time run
INT ccodeStackMainNow	1.3.6.1.4.1.3052.1.18.4	INTEGER	read-only	# of bytes of stack used by main app, this time run
INT ccodeStackT2Was	1.3.6.1.4.1.3052.1.18.5	INTEGER	read-only	# of bytes of stack used by 2nd task of app, last time run
INT ccodeStackT2Was2	1.3.6.1.4.1.3052.1.18.6	INTEGER	read-only	# of bytes of stack used by 2nd task of app, this time run
techsupport	1.3.6.1.4.1.3052.1.99
INT techsupportInt1	1.3.6.1.4.1.3052.1.99.1	INTEGER	read-write	a debugging integer for technical support use only. Do not use
INT techsupportInt2	1.3.6.1.4.1.3052.1.99.2	INTEGER	read-write	a debugging integer for technical support use only. Do not use
INT techsupportInt3	1.3.6.1.4.1.3052.1.99.3	INTEGER	read-write	a debugging integer for technical support use only. Do not use
INT techsupportInt4	1.3.6.1.4.1.3052.1.99.4	INTEGER	read-write	a debugging integer for technical support use only. Do not use
INT techsupportInt5	1.3.6.1.4.1.3052.1.99.5	INTEGER	read-write	a debugging integer for technical support use only. Do not use

RFC description

Asentria datalink product configuration and monitoring including serial ports, SNMP setup, alarms, and controls.

Start monitoring Serial/dial-up modem bank or remote-access router (vendor unclear) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DATALINK-MIB

What Is DATALINK-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description