All MIBs › METRO1500-MIB
Category: WAN
Description: Manages the Metro1500 access multiplexer configuration, interfaces, and alarm status.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is METRO1500-MIB?
METRO1500-MIB is a vendor-specific SNMP module for the Metro1500 access multiplexer, a metro-access/transport aggregation device, defining objects for device inventory, bus-level health, event logging, and trap-sink configuration. It exposes manufacturer, model, serial number, and hardware/software version identity, alongside internal system bus message and error counters and a last-event/message-of-the-day field. Its bus message/error counters and last-event object are the key hardware/software health indicators -- rising metro1500MainBusErrors against metro1500MainBusMessages signals an internal communications or backplane problem within the multiplexer chassis, while metro1500MainLastEvent gives operators the most recent significant event without needing to parse a full log. The module also defines a trapsink table letting the device forward its own traps to one or more NMS destinations, and it appears to be a self-contained enterprise MIB without strong dependency on external standard MIBs. It is deployed on Metro1500 access multiplexer chassis used in metro-area network access/aggregation nodes, and operators managing these chassis typically start with a METRO1500-MIB download to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in METRO1500-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Metro1500 access multiplexer
Monitoring Examples
An operator would monitor metro1500MainBusErrors relative to metro1500MainBusMessages to catch a degrading internal bus before it causes multiplexer-wide faults, and check metro1500MainLastEvent for the most recent significant condition logged by the device. metro1500MainHardwareVersion and metro1500MainSoftwareVersion would be checked during a fleet audit to confirm consistent firmware levels, while metro1500MainTrapsinkTable/metro1500MainTrapsinkEntry is reviewed to ensure the device is correctly configured to forward alerts to the NOC's trap receiver.
What Can Be Monitored
- internal bus message/error counters
- last significant event
- hardware/software version
- trap-sink/alert forwarding configuration
- device serial number/identity
This MIB depends on
Related MIBs
Imported Objects
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| org | 1.3 | |||
| dod | 1.3.6 | |||
| internet | 1.3.6.1 | |||
| private | 1.3.6.1.4 | |||
| enterprises | 1.3.6.1.4.1 | |||
| adva | 1.3.6.1.4.1.2544 | |||
| advaProducts | 1.3.6.1.4.1.2544.1 | |||
| metro1500 | 1.3.6.1.4.1.2544.1.3 | |||
| metro1500Main | 1.3.6.1.4.1.2544.1.3.1 | |||
| metro1500Housing | 1.3.6.1.4.1.2544.1.3.1.1 | |||
| STR metro1500Manufacturer | 1.3.6.1.4.1.2544.1.3.1.1.1 | DisplayString | read-only | Manufacturer of the METRO1500 System |
| STR metro1500MainType | 1.3.6.1.4.1.2544.1.3.1.1.2 | DisplayString | read-only | Type of the METRO1500 System |
| STR metro1500MainSerialNumber | 1.3.6.1.4.1.2544.1.3.1.1.3 | DisplayString | read-only | Serial Number of the METRO1500 System |
| STR metro1500MainHardwareVersion | 1.3.6.1.4.1.2544.1.3.1.1.4 | DisplayString | read-only | Hardware Version of the METRO1500 System |
| STR metro1500MainSoftwareVersion | 1.3.6.1.4.1.2544.1.3.1.1.5 | DisplayString | read-only | Software Version of the METRO1500 System (Device Master). |
| INT metro1500MainBusMessages | 1.3.6.1.4.1.2544.1.3.1.1.6 | INTEGER | read-only | Number of received internal Messages. This Number gives Information on the internal Activity of the METRO1500 System. This should be a large integer Number except when the System has just started. The Value is updated every five Seconds. |
| INT metro1500MainBusErrors | 1.3.6.1.4.1.2544.1.3.1.1.7 | INTEGER | read-only | Number of dropped received internal Messages. This value should be 0 or a very small Integer. |
| INT metro1500MainLastEvent | 1.3.6.1.4.1.2544.1.3.1.1.8 | INTEGER | read-only | Since SNMP Traps are not reliable, this Number can be polled periodically. The Value is set to a nonzero Integer when an Event occurs and cleared ten Minutes after the last Event. |
| STR metro1500MainMotd | 1.3.6.1.4.1.2544.1.3.1.1.9 | DisplayString | read-only | Message Of The Day is the greeting when login via telnet. It shows the actual Kernel Version and the Software Update State. With the MOTD you get Information on the actual installed Software Packets. |
| metro1500MainTrapsinkTable | 1.3.6.1.4.1.2544.1.3.1.1.10 | not-accessible | Table of Trapsinks | |
| metro1500MainTrapsinkEntry | 1.3.6.1.4.1.2544.1.3.1.1.10.1 | not-accessible | Entries in the Trapsink Table | |
| INT metro1500MainTrapsinkNumber | 1.3.6.1.4.1.2544.1.3.1.1.10.1.1 | INTEGER | read-only | Number of Trapsink |
| STR metro1500MainTrapsinkAddress | 1.3.6.1.4.1.2544.1.3.1.1.10.1.2 | DisplayString | read-only | IP Address of the Management System which should receive SNMP Traps. The Logfiles are also shown in this Table |
| STR metro1500MainTrapsinkCommunity | 1.3.6.1.4.1.2544.1.3.1.1.10.1.3 | DisplayString | read-only | Community String which is sent with a SNMP Trap to the Management Station |
| INT metro1500MainTrapsinkPriority | 1.3.6.1.4.1.2544.1.3.1.1.10.1.4 | INTEGER | read-only | Priority of the Trapsink (lower level gets less Traps) |
| metro1500MainLogfileTable | 1.3.6.1.4.1.2544.1.3.1.1.11 | not-accessible | Table of Log Files | |
| metro1500MainLogfileEntry | 1.3.6.1.4.1.2544.1.3.1.1.11.1 | not-accessible | Entries in the Logfile Table | |
| INT metro1500MainLogfileNumber | 1.3.6.1.4.1.2544.1.3.1.1.11.1.1 | INTEGER | read-only | Number of Logfile |
| STR metro1500MainLogfileName | 1.3.6.1.4.1.2544.1.3.1.1.11.1.2 | DisplayString | read-only | Name of Logfile |
| INT metro1500MainLogfileSize | 1.3.6.1.4.1.2544.1.3.1.1.11.1.3 | INTEGER | read-only | Size of Logfile |
| INT metro1500MainLogfilePriority | 1.3.6.1.4.1.2544.1.3.1.1.11.1.4 | INTEGER | read-only | Priority of Logfile |
| metro1500SlotTable | 1.3.6.1.4.1.2544.1.3.1.2 | not-accessible | Table of installed METRO1500 Components. Since METRO1500 can handle many different Components, in this Section only the common Information is displayed. Component specific Information is stored in different Subtrees. | |
| metro1500SlotEntry | 1.3.6.1.4.1.2544.1.3.1.2.1 | not-accessible | Installed METRO1500 Components | |
| INT metro1500SlotNumber | 1.3.6.1.4.1.2544.1.3.1.2.1.1 | INTEGER | read-only | Slot Number of installed Component. The Device Master has always Slot Number 0 and is shown in the Main section. |
| STR metro1500Type | 1.3.6.1.4.1.2544.1.3.1.2.1.2 | DisplayString | read-only | Type of installed Component |
| INT metro1500SlotTypeNumber | 1.3.6.1.4.1.2544.1.3.1.2.1.3 | INTEGER | read-only | Integer Number between 0 and 255 unique for a specific type of installed Component. This Number can be used for management Systems to handle automatically the different Options of installed Components. |
| STR metro1500SerialNumber | 1.3.6.1.4.1.2544.1.3.1.2.1.4 | DisplayString | read-only | Serial Number of installed Component |
| STR metro1500HardwareVersion | 1.3.6.1.4.1.2544.1.3.1.2.1.5 | DisplayString | read-only | Hardware Version of installed Component |
| STR metro1500SoftwareVersion | 1.3.6.1.4.1.2544.1.3.1.2.1.6 | DisplayString | read-only | SoftwareVersion of installed Component |
| INT metro1500Temperature | 1.3.6.1.4.1.2544.1.3.1.2.1.7 | INTEGER | read-only | Temperature of installed Component in Celsius |
| INT metro1500BoardVoltage | 1.3.6.1.4.1.2544.1.3.1.2.1.8 | INTEGER | read-only | Voltage measured directly on the board in mV |
| OID metro1500DetailInfo | 1.3.6.1.4.1.2544.1.3.1.2.1.9 | OBJECT IDENTIFIER | read-only | A Reference to the MIB Definition where the special Options of the Component are described with more Details |
| INT metro1500EPLDVersion | 1.3.6.1.4.1.2544.1.3.1.2.1.10 | INTEGER | read-only | Software Version on the programmable Logic Circuit |
| metro1500PSTable | 1.3.6.1.4.1.2544.1.3.1.3 | not-accessible | Table of installed Power Supplies | |
| metro1500PSEntry | 1.3.6.1.4.1.2544.1.3.1.3.1 | not-accessible | Installed METRO1500 Power Supplies | |
| INT metro1500PSNumber | 1.3.6.1.4.1.2544.1.3.1.3.1.1 | INTEGER | read-only | Number of installed Power Supply |
| INT metro1500PSOn | 1.3.6.1.4.1.2544.1.3.1.3.1.2 | INTEGER | read-only | Is installed Power Supply On or Off |
| metro1500FanTable | 1.3.6.1.4.1.2544.1.3.1.4 | not-accessible | Table of installed Fans | |
| metro1500FanEntry | 1.3.6.1.4.1.2544.1.3.1.4.1 | not-accessible | Installed METRO1500 Fans | |
| INT metro1500FanNumber | 1.3.6.1.4.1.2544.1.3.1.4.1.1 | INTEGER | read-only | Number of installed Fan |
| INT metro1500FanOn | 1.3.6.1.4.1.2544.1.3.1.4.1.2 | INTEGER | read-only | Is installed Fan On or Off |
| metro1500Converter | 1.3.6.1.4.1.2544.1.3.5 | |||
| metro1500ConverterTable | 1.3.6.1.4.1.2544.1.3.5.1 | not-accessible | Table of installed METRO1500 Converters | |
| metro1500ConverterEntry | 1.3.6.1.4.1.2544.1.3.5.1.1 | not-accessible | Installed METRO1500 Converters | |
| INT metro1500ConverterNumber | 1.3.6.1.4.1.2544.1.3.5.1.1.1 | INTEGER | read-only | Slot Number of installed Converter Card |
| INT metro1500RxLoc | 1.3.6.1.4.1.2544.1.3.5.1.1.2 | INTEGER | read-only | Local Receiver has Signal (On) or Loss of Signal (Off) |
| INT metro1500TxLoc | 1.3.6.1.4.1.2544.1.3.5.1.1.3 | INTEGER | read-only | Local Transmitter is On or Off |
| INT metro1500TxLocC | 1.3.6.1.4.1.2544.1.3.5.1.1.4 | INTEGER | read-only | Current of the local Transmitter in mA. This Entry is only available if a Current Sensor is installed |
| INT metro1500TxLocTemp | 1.3.6.1.4.1.2544.1.3.5.1.1.5 | INTEGER | read-only | Temperature of the local Transmitter in Celsius. This Entry is only available if the Laser is cooled |
| INT metro1500RxRem | 1.3.6.1.4.1.2544.1.3.5.1.1.6 | INTEGER | read-only | Remote Receiver has Signal (On) or Loss of Signal (Off) |
| INT metro1500TxRem | 1.3.6.1.4.1.2544.1.3.5.1.1.7 | INTEGER | read-only | Remote Transmitter is On or Off |
| INT metro1500TxRemC | 1.3.6.1.4.1.2544.1.3.5.1.1.8 | INTEGER | read-only | Current of the Remote Transmitter in Milli Ampere. This Entry is only available if a Current Sensor is installed |
| INT metro1500TxRemTemp | 1.3.6.1.4.1.2544.1.3.5.1.1.9 | INTEGER | read-only | Temperature of the Remote Transmitter in Celsius This Entry is only available if the Laser is cooled |
| INT metro1500RxRem2 | 1.3.6.1.4.1.2544.1.3.5.1.1.10 | INTEGER | read-only | 2nd Remote receiver has Signal (On) or Loss of Signal (Off). (Only available if a 2nd Remote Receiver is installed) |
| INT metro1500ClockState | 1.3.6.1.4.1.2544.1.3.5.1.1.11 | INTEGER | read-only | Status of the Clock. This Entry is only available if a Clock is installed. If the Clock is enabled, and has an error output, and cannot synchronize to the Signal, the Clock fails. |
| INT metro1500ClockFreq | 1.3.6.1.4.1.2544.1.3.5.1.1.12 | INTEGER | read-only | Frequency of the Clock in MBit/s. Only available if a Clock is installed. |
| INT metro1500LocLoop | 1.3.6.1.4.1.2544.1.3.5.1.1.13 | INTEGER | read-only | Local Loop is set to On or to Off |
| INT metro1500RemLoop | 1.3.6.1.4.1.2544.1.3.5.1.1.14 | INTEGER | read-only | Remote Loop is set to On or to Off |
| INT metro1500ClockType | 1.3.6.1.4.1.2544.1.3.5.1.1.15 | INTEGER | read-only | Type of the Clock. Only available, if a Clock is installed. |
| metro1500Switch | 1.3.6.1.4.1.2544.1.3.10 | |||
| metro1500SwitchTable | 1.3.6.1.4.1.2544.1.3.10.1 | not-accessible | Table of installed METRO1500 Switches | |
| metro1500SwitchEntry | 1.3.6.1.4.1.2544.1.3.10.1.1 | not-accessible | Installed METRO1500 Switches | |
| INT metro1500SwitchNumber | 1.3.6.1.4.1.2544.1.3.10.1.1.1 | INTEGER | read-only | Slot Number of installed Remote Optical Switch Card |
| INT metro1500SwitchLine | 1.3.6.1.4.1.2544.1.3.10.1.1.2 | INTEGER | read-only | Active Line of Remote Optical Switch |
| INT metro1500SwitchMode | 1.3.6.1.4.1.2544.1.3.10.1.1.3 | INTEGER | read-only | Mode of Transmit Line of Remote Optical Switch |
| INT metro1500SwitchLaserOn | 1.3.6.1.4.1.2544.1.3.10.1.1.4 | INTEGER | read-only | Shows if the reference Laser is On or Off |
| metro1500EthernetHub | 1.3.6.1.4.1.2544.1.3.14 | |||
| metro1500EthernetHubTable | 1.3.6.1.4.1.2544.1.3.14.1 | not-accessible | Table of installed FSP-II Hub Cards | |
| metro1500EthernetHubEntry | 1.3.6.1.4.1.2544.1.3.14.1.1 | not-accessible | Installed FSP-II Hub Cards | |
| INT metro1500EthernetHubNumber | 1.3.6.1.4.1.2544.1.3.14.1.1.1 | INTEGER | read-only | Slot Number of installed Hub Card |
| INT metro1500EthernetHubPortEnable1 | 1.3.6.1.4.1.2544.1.3.14.1.1.10 | INTEGER | read-only | is Hub Port 1 enabled ? |
| INT metro1500EthernetHubPortPartitionStatus1 | 1.3.6.1.4.1.2544.1.3.14.1.1.11 | INTEGER | read-only | is Port 1 partitioned ? |
| INT metro1500EthernetHubPortLinkStatus1 | 1.3.6.1.4.1.2544.1.3.14.1.1.12 | INTEGER | read-only | does Port 1 receive Link Pulses ? |
| INT metro1500EthernetHubPortPolarity1 | 1.3.6.1.4.1.2544.1.3.14.1.1.13 | INTEGER | read-only | polarity of input signal at Port 1 |
| INT metro1500EthernetHubPortEnable2 | 1.3.6.1.4.1.2544.1.3.14.1.1.20 | INTEGER | read-only | is Hub Port 2 enabled ? |
| INT metro1500EthernetHubPortPartitionStatus2 | 1.3.6.1.4.1.2544.1.3.14.1.1.21 | INTEGER | read-only | is Port 2 partitioned ? |
| INT metro1500EthernetHubPortLinkStatus2 | 1.3.6.1.4.1.2544.1.3.14.1.1.22 | INTEGER | read-only | does Port 2 receive Link Pulses ? |
| INT metro1500EthernetHubPortPolarity2 | 1.3.6.1.4.1.2544.1.3.14.1.1.23 | INTEGER | read-only | polarity of input signal at Port 2 |
| INT metro1500EthernetHubPortEnable3 | 1.3.6.1.4.1.2544.1.3.14.1.1.30 | INTEGER | read-only | is Hub Port 3 enabled ? |
| INT metro1500EthernetHubPortPartitionStatus3 | 1.3.6.1.4.1.2544.1.3.14.1.1.31 | INTEGER | read-only | is Port 3 partitioned ? |
| INT metro1500EthernetHubPortLinkStatus3 | 1.3.6.1.4.1.2544.1.3.14.1.1.32 | INTEGER | read-only | does Port 3 receive Link Pulses ? |
| INT metro1500EthernetHubPortPolarity3 | 1.3.6.1.4.1.2544.1.3.14.1.1.33 | INTEGER | read-only | polarity of input signal at Port 3 |
| INT metro1500EthernetHubPortEnable4 | 1.3.6.1.4.1.2544.1.3.14.1.1.40 | INTEGER | read-only | is Hub Port 4 enabled ? |
| INT metro1500EthernetHubPortPartitionStatus4 | 1.3.6.1.4.1.2544.1.3.14.1.1.41 | INTEGER | read-only | is Port 4 partitioned ? |
| INT metro1500EthernetHubPortLinkStatus4 | 1.3.6.1.4.1.2544.1.3.14.1.1.42 | INTEGER | read-only | does Port 4 receive Link Pulses ? |
| INT metro1500EthernetHubPortPolarity4 | 1.3.6.1.4.1.2544.1.3.14.1.1.43 | INTEGER | read-only | polarity of input signal at Port 4 |
| INT metro1500EthernetHubPortEnable5 | 1.3.6.1.4.1.2544.1.3.14.1.1.50 | INTEGER | read-only | is Hub Port 5 enabled ? |
| INT metro1500EthernetHubPortPartitionStatus5 | 1.3.6.1.4.1.2544.1.3.14.1.1.51 | INTEGER | read-only | is Port 5 partitioned ? |
| INT metro1500EthernetHubPortLinkStatus5 | 1.3.6.1.4.1.2544.1.3.14.1.1.52 | INTEGER | read-only | does Port 5 receive Link Pulses ? |
| INT metro1500EthernetHubPortPolarity5 | 1.3.6.1.4.1.2544.1.3.14.1.1.53 | INTEGER | read-only | polarity of input signal at Port 5 |
| metro1500TDM | 1.3.6.1.4.1.2544.1.3.15 | |||
| metro1500TDMTable | 1.3.6.1.4.1.2544.1.3.15.1 | not-accessible | Table of installed FSP-II TDM Cards | |
| metro1500TDMEntry | 1.3.6.1.4.1.2544.1.3.15.1.1 | not-accessible | Installed FSP-II TDM Cards | |
| INT metro1500TDMNumber | 1.3.6.1.4.1.2544.1.3.15.1.1.1 | INTEGER | read-only | Slot Number of installed TDM Card |
| INT metro1500TDMRxRem | 1.3.6.1.4.1.2544.1.3.15.1.1.4 | INTEGER | read-only | Does the remote receiver receive Light (on) or not (off)? |
| INT metro1500TDMRxSync | 1.3.6.1.4.1.2544.1.3.15.1.1.5 | INTEGER | read-only | Is the input signal synchronized with the corresponding TDM card? |
| INT metro1500TDMTxRem | 1.3.6.1.4.1.2544.1.3.15.1.1.6 | INTEGER | read-only | State of the Remote Transmitter |
| INT metro1500TDMTxRemC | 1.3.6.1.4.1.2544.1.3.15.1.1.7 | INTEGER | read-only | Current of the remote Transmitter in mA |
| INT metro1500TDMTxRemTemp | 1.3.6.1.4.1.2544.1.3.15.1.1.8 | INTEGER | read-only | Temperature of the remote Transmitter in Celsius |
| INT metro1500TDMLocLoop | 1.3.6.1.4.1.2544.1.3.15.1.1.9 | INTEGER | read-only | Loop for all Local Inputs enabled (on) or disabled (off) |
| INT metro1500TDMLocModuleInst1 | 1.3.6.1.4.1.2544.1.3.15.1.1.20 | INTEGER | read-only | is local Module 1 installed ? |
| INT metro1500TDMLocModuleEnable1 | 1.3.6.1.4.1.2544.1.3.15.1.1.21 | INTEGER | read-only | is local Module 1 enabled ? |
| INT metro1500TDMLocModuleRx1 | 1.3.6.1.4.1.2544.1.3.15.1.1.22 | INTEGER | read-only | local receiver 1 gets signal (on) |
| INT metro1500TDMLocModuleTx1 | 1.3.6.1.4.1.2544.1.3.15.1.1.23 | INTEGER | read-only | state of the local transmitter |
| INT metro1500TDMLocModuleRemoteData1 | 1.3.6.1.4.1.2544.1.3.15.1.1.24 | INTEGER | read-only | receiving data for this module from the remote side |
| INT metro1500TDMLocModuleClockFrequency1 | 1.3.6.1.4.1.2544.1.3.15.1.1.25 | INTEGER | read-only | data rate of the clock installed on local Module 1 in MBit/s |
| INT metro1500TDMLocModuleClockError1 | 1.3.6.1.4.1.2544.1.3.15.1.1.26 | INTEGER | read-only | data rate and clock frequency are not synchronized |
| INT metro1500TDMLocModuleInst2 | 1.3.6.1.4.1.2544.1.3.15.1.1.30 | INTEGER | read-only | is local Module 2 installed ? |
| INT metro1500TDMLocModuleEnable2 | 1.3.6.1.4.1.2544.1.3.15.1.1.31 | INTEGER | read-only | is local Module 2 enabled ? |
| INT metro1500TDMLocModuleRx2 | 1.3.6.1.4.1.2544.1.3.15.1.1.32 | INTEGER | read-only | local receiver 2 gets signal (on) |
| INT metro1500TDMLocModuleTx2 | 1.3.6.1.4.1.2544.1.3.15.1.1.33 | INTEGER | read-only | state of the local transmitter |
| INT metro1500TDMLocModuleRemoteData2 | 1.3.6.1.4.1.2544.1.3.15.1.1.34 | INTEGER | read-only | receiving data for this module from the remote side |
| INT metro1500TDMLocModuleClockFrequency2 | 1.3.6.1.4.1.2544.1.3.15.1.1.35 | INTEGER | read-only | data rate of the clock installed on local Module 2 in MBit/s |
| INT metro1500TDMLocModuleClockError2 | 1.3.6.1.4.1.2544.1.3.15.1.1.36 | INTEGER | read-only | data rate and clock frequency are not synchronized |
| INT metro1500TDMLocModuleInst3 | 1.3.6.1.4.1.2544.1.3.15.1.1.40 | INTEGER | read-only | is local Module 3 installed ? |
| INT metro1500TDMLocModuleEnable3 | 1.3.6.1.4.1.2544.1.3.15.1.1.41 | INTEGER | read-only | is local Module 3 enabled ? |
| INT metro1500TDMLocModuleRx3 | 1.3.6.1.4.1.2544.1.3.15.1.1.42 | INTEGER | read-only | local receiver 3 gets signal (on) |
| INT metro1500TDMLocModuleTx3 | 1.3.6.1.4.1.2544.1.3.15.1.1.43 | INTEGER | read-only | state of the local transmitter |
| INT metro1500TDMLocModuleRemoteData3 | 1.3.6.1.4.1.2544.1.3.15.1.1.44 | INTEGER | read-only | receiving data for this module from the remote side |
| INT metro1500TDMLocModuleClockFrequency3 | 1.3.6.1.4.1.2544.1.3.15.1.1.45 | INTEGER | read-only | data rate of the clock installed on local Module 3 in MBit/s |
| INT metro1500TDMLocModuleClockError3 | 1.3.6.1.4.1.2544.1.3.15.1.1.46 | INTEGER | read-only | data rate and clock frequency are not synchronized |
| INT metro1500TDMLocModuleInst4 | 1.3.6.1.4.1.2544.1.3.15.1.1.50 | INTEGER | read-only | is local Module 4 installed ? |
| INT metro1500TDMLocModuleEnable4 | 1.3.6.1.4.1.2544.1.3.15.1.1.51 | INTEGER | read-only | is local Module 4 enabled ? |
| INT metro1500TDMLocModuleRx4 | 1.3.6.1.4.1.2544.1.3.15.1.1.52 | INTEGER | read-only | local receiver 4 gets signal (on) |
| INT metro1500TDMLocModuleTx4 | 1.3.6.1.4.1.2544.1.3.15.1.1.53 | INTEGER | read-only | state of the local transmitter |
| INT metro1500TDMLocModuleRemoteData4 | 1.3.6.1.4.1.2544.1.3.15.1.1.54 | INTEGER | read-only | receiving data for this module from the remote side |
| INT metro1500TDMLocModuleClockFrequency4 | 1.3.6.1.4.1.2544.1.3.15.1.1.55 | INTEGER | read-only | data rate of the clock installed on local Module 4 in MBit/s |
| INT metro1500TDMLocModuleClockError4 | 1.3.6.1.4.1.2544.1.3.15.1.1.56 | INTEGER | read-only | data rate and clock frequency are not synchronized |
| metro1500Trap | 1.3.6.1.4.1.2544.1.3.100 | |||
| NTF metro1500HardwareAdded | 1.3.6.1.4.1.2544.1.3.100.0.1 | Trap is sent when a new Module is inserted into the FSP-I Box | ||
| NTF metro1500HardwareDeleted | 1.3.6.1.4.1.2544.1.3.100.0.2 | Trap is sent when a Module is removed from the FSP-I Box | ||
| NTF metro1500PSNotFail | 1.3.6.1.4.1.2544.1.3.100.0.3 | Trap is sent when a Power Supply starts working | ||
| NTF metro1500PSFail | 1.3.6.1.4.1.2544.1.3.100.0.4 | Trap is sent when a Power Supply fails | ||
| NTF metro1500FanNotFail | 1.3.6.1.4.1.2544.1.3.100.0.5 | Trap is sent when a Fan starts working | ||
| NTF metro1500FanFail | 1.3.6.1.4.1.2544.1.3.100.0.6 | Trap is sent when a Fan fails | ||
| NTF metro1500BusNotFail | 1.3.6.1.4.1.2544.1.3.100.0.7 | Trap is sent when the internal Bus starts working again | ||
| NTF metro1500BusFail | 1.3.6.1.4.1.2544.1.3.100.0.8 | Trap is sent when an internal Bus Failure occurs | ||
| NTF metro1500RxLocOn | 1.3.6.1.4.1.2544.1.3.100.0.20 | Trap is sent when the local Receiver gets Signal | ||
| NTF metro1500RxLocOff | 1.3.6.1.4.1.2544.1.3.100.0.21 | Trap is sent when the local Receiver has Loss of Signal | ||
| NTF metro1500TxLocOn | 1.3.6.1.4.1.2544.1.3.100.0.22 | Trap is sent when the local Transmitter is switched on, Either this trap or Trap #20 should be disabled in the Configuration because they are typically sent at the same Time. | ||
| NTF metro1500TxLocOff | 1.3.6.1.4.1.2544.1.3.100.0.23 | Trap is sent when the local Transmitter is switched off, Either this trap or Trap #21 should be disabled in the Configuration because they are typically sent at the same Time. | ||
| NTF metro1500RxRemOn | 1.3.6.1.4.1.2544.1.3.100.0.24 | Trap is sent when the remote Receiver gets Signal | ||
| NTF metro1500RxRemOff | 1.3.6.1.4.1.2544.1.3.100.0.25 | Trap is sent when the remote Receiver has Loss of Signal | ||
| NTF metro1500TxRemOn | 1.3.6.1.4.1.2544.1.3.100.0.26 | Trap is sent when the remote Transmitter is switched on, Either this trap or Trap #24 should be disabled in the Configuration because they are typically sent at the same Time. | ||
| NTF metro1500TxRemOff | 1.3.6.1.4.1.2544.1.3.100.0.27 | Trap is sent when the remote Transmitter is switched off, Either this trap or Trap #25 should be disabled in the Configuration because they are typically sent at the same Time. | ||
| NTF metro1500RxRem2On | 1.3.6.1.4.1.2544.1.3.100.0.28 | Trap is sent when the 2nd remote Receiver gets Signal. This Trap is only sent if there is a 2nd remote Receiver. | ||
| NTF metro1500RxRem2Off | 1.3.6.1.4.1.2544.1.3.100.0.29 | Trap is sent when the 2nd remote Receiver has Loss of Signal. This Trap is only sent if there is a 2nd remote Receiver. | ||
| NTF metro1500TxRem2On | 1.3.6.1.4.1.2544.1.3.100.0.30 | Trap is sent when the 2nd remote Transmitter is switched on, Either this Trap or Trap #28 should be disabled in the Configuration because they are typically sent at the same Time. This Trap is only sent if there is a 2nd remote Receiver. | ||
| NTF metro1500TxRem2Off | 1.3.6.1.4.1.2544.1.3.100.0.31 | Trap is sent when the 2nd remote Transmitter is switched off, Either this trap or Trap #29 should be disabled in the Configuration because they are typically sent at the same Time. | ||
| NTF metro1500ClockNoFail | 1.3.6.1.4.1.2544.1.3.100.0.32 | Trap is sent if a Clock is installed and can synchronize with the input Signal. This Trap is not sent if the installed Clock does not have an error Output | ||
| NTF metro1500ClockFail | 1.3.6.1.4.1.2544.1.3.100.0.33 | Trap is sent if a Clock is installed and can not synchronize with the input Signal. This trap is not sent if the installed Clock does not have an error Output | ||
| NTF metro1500ClockChangeFrequency | 1.3.6.1.4.1.2544.1.3.100.0.34 | Trap is sent if a multi frequency Clock is installed and changes its frequency. | ||
| NTF metro1500LocLoopOn | 1.3.6.1.4.1.2544.1.3.100.0.35 | Trap is sent if Local Loop is set to On. | ||
| NTF metro1500LocLoopOff | 1.3.6.1.4.1.2544.1.3.100.0.36 | Trap is sent if Local Loop is set to Off. | ||
| NTF metro1500RemLoopOn | 1.3.6.1.4.1.2544.1.3.100.0.37 | Trap is sent if Remote Loop is set to On. | ||
| NTF metro1500RemLoopOff | 1.3.6.1.4.1.2544.1.3.100.0.38 | Trap is sent if Remote Loop is set to Off. | ||
| NTF metro1500switchReferenceLaserOn | 1.3.6.1.4.1.2544.1.3.100.0.40 | Trap is sent when the Reference Laser is switched on | ||
| NTF metro1500switchReferenceLaserOff | 1.3.6.1.4.1.2544.1.3.100.0.41 | Trap is sent when the Reference Laser is switched off | ||
| NTF metro1500switchToA | 1.3.6.1.4.1.2544.1.3.100.0.42 | Trap is sent when the Switch switches to Line A | ||
| NTF metro1500switchToB | 1.3.6.1.4.1.2544.1.3.100.0.43 | Trap is sent when the Switch switches to Line B | ||
| NTF metro1500switchAutomatic | 1.3.6.1.4.1.2544.1.3.100.0.44 | Trap is sent when the Switch is going to Automatic State | ||
| NTF metro1500switchLocked | 1.3.6.1.4.1.2544.1.3.100.0.45 | Trap is sent when the Switch is going to Locked State | ||
| NTF metro1500SwitchLineAavail | 1.3.6.1.4.1.2544.1.3.100.0.46 | Trap is sent when the Switch Line A is available | ||
| NTF metro1500switchLineANotAvail | 1.3.6.1.4.1.2544.1.3.100.0.47 | Trap is sent when the Switch Line A is not available | ||
| NTF metro1500SwitchLineBavail | 1.3.6.1.4.1.2544.1.3.100.0.48 | Trap is sent when the Switch Line B is available | ||
| NTF metro1500switchLineBNotAvail | 1.3.6.1.4.1.2544.1.3.100.0.49 | Trap is sent when the Switch Line B is not available | ||
| NTF metro1500repeatedMessage | 1.3.6.1.4.1.2544.1.3.100.0.50 | Trap is sent, after three times the same trap is sent (instead of the fourth one). The original trap is suppressed for one minute. | ||
| NTF metro1500INNCDown | 1.3.6.1.4.1.2544.1.3.100.0.51 | Trap is sent, when the Inter NEMI Network Connection (INNC) is down. | ||
| NTF metro1500INNCUp | 1.3.6.1.4.1.2544.1.3.100.0.52 | Trap is sent, when the Inter NEMI Network Connection (INNC) is up. | ||
| NTF metro1500EthernetHubPortEnable | 1.3.6.1.4.1.2544.1.3.100.0.60 | Trap is sent, when one of the ports of the Ethernet Hub is enabled by the management software (default). Use SNMP Get to get the Port Number. | ||
| NTF metro1500EthernetHubPortDisable | 1.3.6.1.4.1.2544.1.3.100.0.61 | Trap is sent, when one of the ports of the Ethernet Hub is disabled by the management Software. Use SNMP Get to get the Port number. | ||
| NTF metro1500EthernetHubPortPartitioned | 1.3.6.1.4.1.2544.1.3.100.0.62 | Trap is sent, when a Hub Port is disabled by the Hub Hardware. Use SNMP Get to get the Port Number. | ||
| NTF metro1500EthernetHubPortNotPartitioned | 1.3.6.1.4.1.2544.1.3.100.0.63 | Trap is sent, when a Hub Port is enabled by the Hub Hardware (default). Use SNMP Get to get the Port Number. | ||
| NTF metro1500EthernetHubPortLinkPulses | 1.3.6.1.4.1.2544.1.3.100.0.64 | Trap is sent, when a Hub Port starts receiving Link Pulses. Use SNMP Get to get the Port Number | ||
| NTF metro1500EthernetHubPortNoLinkPulses | 1.3.6.1.4.1.2544.1.3.100.0.65 | Trap is sent, when a Hub Port stops receiving Link Pulses. Use SNMP Get to get the Port Number | ||
| NTF metro1500TDMRemoteSyncLoss | 1.3.6.1.4.1.2544.1.3.100.0.70 | Trap is sent, when the synchronisation of the incoming remote data stream is lost | ||
| NTF metro1500TDMRemoteSync | 1.3.6.1.4.1.2544.1.3.100.0.71 | Trap is sent, when the synchronisation of the incoming remote data stream is established | ||
| NTF metro1500TDMLocModuleEnabled1 | 1.3.6.1.4.1.2544.1.3.100.0.72 | Trap is sent, when local module 1 is enabled by software | ||
| NTF metro1500TDMLocModuleDisable1 | 1.3.6.1.4.1.2544.1.3.100.0.73 | Trap is sent, when local module 1 is disabled by software | ||
| NTF metro1500TDMLocModuleEnabled2 | 1.3.6.1.4.1.2544.1.3.100.0.74 | Trap is sent, when local module 2 is enabled by software | ||
| NTF metro1500TDMLocModuleDisable2 | 1.3.6.1.4.1.2544.1.3.100.0.75 | Trap is sent, when local module 2 is disabled by software | ||
| NTF metro1500TDMLocModuleEnabled3 | 1.3.6.1.4.1.2544.1.3.100.0.76 | Trap is sent, when local module 3 is enabled by software | ||
| NTF metro1500TDMLocModuleDisable3 | 1.3.6.1.4.1.2544.1.3.100.0.77 | Trap is sent, when local module 3 is disabled by software | ||
| NTF metro1500TDMLocModuleEnabled4 | 1.3.6.1.4.1.2544.1.3.100.0.78 | Trap is sent, when local module 4 is enabled by software | ||
| NTF metro1500TDMLocModuleDisable4 | 1.3.6.1.4.1.2544.1.3.100.0.79 | Trap is sent, when local module 4 is disabled by software | ||
| NTF metro1500TDMLocModuleRxOn1 | 1.3.6.1.4.1.2544.1.3.100.0.88 | Trap is sent, when the local receiver 1 of a TDM card gets modulated signal | ||
| NTF metro1500TDMLocModuleRxOff1 | 1.3.6.1.4.1.2544.1.3.100.0.89 | Trap is sent, when the local receiver 1 of a TDM card doesn't get modulated signal | ||
| NTF metro1500TDMLocModuleRxOn2 | 1.3.6.1.4.1.2544.1.3.100.0.90 | Trap is sent, when the local receiver 2 of a TDM card gets modulated signal | ||
| NTF metro1500TDMLocModuleRxOff2 | 1.3.6.1.4.1.2544.1.3.100.0.91 | Trap is sent, when the local receiver 2 of a TDM card doesn't get modulated signal | ||
| NTF metro1500TDMLocModuleRxOn3 | 1.3.6.1.4.1.2544.1.3.100.0.92 | Trap is sent, when the local receiver 3 of a TDM card gets modulated signal | ||
| NTF metro1500TDMLocModuleRxOff3 | 1.3.6.1.4.1.2544.1.3.100.0.93 | Trap is sent, when the local receiver 3 of a TDM card doesn't get modulated signal | ||
| NTF metro1500TDMLocModuleRxOn4 | 1.3.6.1.4.1.2544.1.3.100.0.94 | Trap is sent, when the local receiver 4 of a TDM card gets modulated signal | ||
| NTF metro1500TDMLocModuleRxOff4 | 1.3.6.1.4.1.2544.1.3.100.0.95 | Trap is sent, when the local receiver 4 of a TDM card doesn't get modulated signal | ||
| NTF metro1500TDMLocModuleData1 | 1.3.6.1.4.1.2544.1.3.100.0.104 | Trap is sent, when data from the remote side is available for this TDM channel | ||
| NTF metro1500TDMLocModuleNoData1 | 1.3.6.1.4.1.2544.1.3.100.0.105 | Trap is sent, when no data from the remote side is available for this TDM channel | ||
| NTF metro1500TDMLocModuleData2 | 1.3.6.1.4.1.2544.1.3.100.0.106 | Trap is sent, when data from the remote side is available for this TDM channel | ||
| NTF metro1500TDMLocModuleNoData2 | 1.3.6.1.4.1.2544.1.3.100.0.107 | Trap is sent, when no data from the remote side is available for this TDM channel | ||
| NTF metro1500TDMLocModuleData3 | 1.3.6.1.4.1.2544.1.3.100.0.108 | Trap is sent, when data from the remote side is available for this TDM channel | ||
| NTF metro1500TDMLocModuleNoData3 | 1.3.6.1.4.1.2544.1.3.100.0.109 | Trap is sent, when no data from the remote side is available for this TDM channel | ||
| NTF metro1500TDMLocModuleData4 | 1.3.6.1.4.1.2544.1.3.100.0.110 | Trap is sent, when data from the remote side is available for this TDM channel | ||
| NTF metro1500TDMLocModuleNoData4 | 1.3.6.1.4.1.2544.1.3.100.0.111 | Trap is sent, when no data from the remote side is available for this TDM channel | ||
| NTF metro1500TDMLocModuleClockFail1 | 1.3.6.1.4.1.2544.1.3.100.0.120 | Trap is sent, when the Data Rate of the local input signal doesn't match the Data Rate of the local clock | ||
| NTF metro1500TDMLocModuleClockNoFail1 | 1.3.6.1.4.1.2544.1.3.100.0.121 | Trap is sent, when the Data Rate of the local input signal matches the Data Rate of the local clock | ||
| NTF metro1500TDMLocModuleClockFail2 | 1.3.6.1.4.1.2544.1.3.100.0.122 | Trap is sent, when the Data Rate of the local input signal doesn't match the Data Rate of the local clock | ||
| NTF metro1500TDMLocModuleClockNoFail2 | 1.3.6.1.4.1.2544.1.3.100.0.123 | Trap is sent, when the Data Rate of the local input signal matches the Data Rate of the local clock | ||
| NTF metro1500TDMLocModuleClockFail3 | 1.3.6.1.4.1.2544.1.3.100.0.124 | Trap is sent, when the Data Rate of the local input signal doesn't match the Data Rate of the local clock | ||
| NTF metro1500TDMLocModuleClockNoFail3 | 1.3.6.1.4.1.2544.1.3.100.0.125 | Trap is sent, when the Data Rate of the local input signal matches the Data Rate of the local clock | ||
| NTF metro1500TDMLocModuleClockFail4 | 1.3.6.1.4.1.2544.1.3.100.0.126 | Trap is sent, when the Data Rate of the local input signal doesn't match the Data Rate of the local clock | ||
| NTF metro1500TDMLocModuleClockNoFail4 | 1.3.6.1.4.1.2544.1.3.100.0.127 | Trap is sent, when the Data Rate of the local input signal matches the Data Rate of the local clock |
RFC description
Vendor management MIB for the Metro 1500 product/platform; manages device configuration and operational status.
Start monitoring ADVA/vendor Metro1500 access multiplexer with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.