All MIBs › CISCO-SDSL-LINE-MIB
Organization: Cisco Systems, Inc.
Last Updated: 2001-08-20
Category: Cisco Devices, DSL and Broadband
Description: Manages and monitors Symmetric DSL (SDSL) line configuration, status, and performance statistics on Cisco DSL equipment.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CISCO-SDSL-LINE-MIB?
CISCO-SDSL-LINE-MIB manages and monitors Symmetric DSL (SDSL) line interfaces on Cisco DSL access equipment, extending the IETF ADSL-LINE-MIB family to cover symmetric-rate DSL variants. It belongs to Cisco's broadband access/DSLAM and CPE router product area. The MIB exposes line configuration (coding, framing, line-specific mode, configuration and alarm profiles) alongside physical/inventory data such as vendor ID, serial number, and firmware version of the DSL transceiver unit. For hardware and software status monitoring it is particularly useful for tracking DSL line/modem inventory (serial number, vendor ID, version number) and alarm-profile-driven fault conditions, complementing physical-layer health visibility beyond simple up/down interface status. It explicitly models itself after and maintains structural consistency with ADSL-LINE-MIB, ADSL-DMT-LINE-MIB, CISCO-ADSL-DMT-LINE-MIB, and CISCO-ADSL-CAP-LINE-MIB, extending their profile tables for configuration. It is deployed on Cisco routers and DSLAMs providing symmetric DSL last-mile connectivity to business customers, where CISCO-SDSL-LINE-MIB SNMP monitoring supports line inventory and alarm-profile-driven fault tracking.
IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-SDSL-LINE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cisco SDSL DSLAMs and routers with SDSL line cards
Monitoring Examples
An operator would poll cSdslLineTable/cSdslLineEntry to check cSdslLineCoding, cSdslLineFraming, and cSdslLineConfProfile for each SDSL line, verifying the line is provisioned with the expected coding scheme and configuration profile. The cSdslStucPhysTable/cSdslStucPhysEntry exposes cSdslStucInvSerialNumber, cSdslStucInvVendorId, and cSdslStucInvVersionNumber, letting an admin inventory the DSL transceiver hardware and firmware version deployed at each site. Notifications tied to cSdslLineAlarmConfProfile would alert on line degradation such as excessive errors or loss of sync.
What Can Be Monitored
- SDSL line coding/framing configuration
- line configuration/alarm profile status
- DSL transceiver vendor ID and serial number
- firmware/version number of DSL unit
- line alarm conditions
This MIB depends on
Related MIBs
Imported Objects
From ADSL-LINE-MIB
| AdslLineProfileName | |
| adslLineAlarmConfProfileName | OBJECT-TYPE |
| adslLineConfProfileName | OBJECT-TYPE |
From CISCO-SMI
| ciscoMgmt | OBJECT-IDENTITY |
From IF-MIB
| ifIndex | OBJECT-TYPE |
From PerfHist-TC-MIB
| PerfCurrentCount | |
| PerfIntervalCount |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE |
From SNMPv2-TC
| TEXTUAL-CONVENTION | |
| TruthValue | |
| VariablePointer |
How to Use in IPNetwork Monitor
Example using cSdslStucPerfLOSs OID:
Select a Cisco SDSL DSLAMs and routers with SDSL line card as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cSdslStucPerfLOSs into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This object specifies the number of LOS failures experienced by the STU-C since agent reset. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| ciscoSdslLineMIB | 1.3.6.1.4.1.9.9.155 | This MIB module describes all variations of the symmetric DSL line interfaces. The structure of this module resembles and maintains consistency with the ADSL-LINE-MIB, ADSL-DMT-LINE-MIB, CISCO-ADSL-DMT-LINE-MIB, and CISCO-ADSL-CAP-LINE-MIB. Observe that the tables in this module do not necessarily extend the tables defined by the these mibs. Currently, only those tables that contain configuration information extend the profile tables defined by the above modules. This allows the management client to define DSL configuration profiles that apply across all DSL modems, independent of the technology being utilized by the modem. *** DEFINITIONS *** ATTENUATION Attenuation is a decrease in the strength of a signal over the length of a cable. CODING VIOLATION A coding violation occurs when the incoming signal exhibits a CRC anomaly. DOWNSTREAM The flow of data in the direction from the ATU-C to ATU-R. ERRORED SECOND A second with one or more coding violations or one or more incoming defects (e.g., LOS or LOSQ). LINE RATE The total data rate supported by a line. Observe that the payload rate is equal the line rate for the earliest implementations of SDSL. However, the payload rate maybe less than the line rate for future implementations. LOSS OF SYNC DEFECT A Loss of Sync Defect is defined as 3 consecutive received frames which contain one or more errors in the framing bits. A Loss of Sync Defect shall be cleared when at least 2 consecutive received frames contain no errors in the framing bits. LOSS OF SYNC FAILURE A LOSW Failure is defined as at least 2 consecutive seconds of LOSW Defect. The LOSW Failure should be cleared when the LOSW defect is absent for 20 seconds or less. (i.e. clear within 20 seconds ). MARGIN (also referred to as 'SNR margin') The difference between the SNR of the received signal and the SNR required to provide a BER of 10E-7. SEVERELY ERRORED SECOND A one second interval during which or more LOSW or CV defects are declared. UNAVAILABLE SECOND A Unavailable Second is defined as a one second interval during which LOSW Failure ( at least 2 seconds of LOSW Defect ). UPSTREAM The flow of data in the direction from the ATU-R to ATU-C. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS *** ADSL - Asymmetric Digital Subscriber Line. ATM - Asynchronous Transfer Mode. BER - Bit Error Ratio. CV - Coding Violation. DSL - Digital Subscriber Line. ES - Errored Second. LOS - Loss Of Sync. LOSQ - Loss Of Signal Quality. LOSW - Loss of Sync Word Failure PSD - Power Spectral Density. SES - Severely Errored Second. SNR - Signal-to-Noise Ratio. STM - Synchronous Transfer Mode. STU-C - SDSL Transceiver Unit, Central Office end. STU-R - ADSL Transceiver Unit, Remote terminal end. UAS - UnAvailable Second. | ||
| ciscoSdslLineMIBCompliances | 1.3.6.1.4.1.9.9.155.3.1 | |||
| ciscoSdslLineMIBConformance | 1.3.6.1.4.1.9.9.155.3 | |||
| ciscoSdslLineMIBGroups | 1.3.6.1.4.1.9.9.155.3.2 | |||
| ciscoSdslLineMIBNotifications | 1.3.6.1.4.1.9.9.155.2.0 | |||
| ciscoSdslLineMIBNotificationsPrefix | 1.3.6.1.4.1.9.9.155.2 | |||
| ciscoSdslLineMIBObjects | 1.3.6.1.4.1.9.9.155.1 | |||
| ciscoSdslLineMIBStucCompliance | 1.3.6.1.4.1.9.9.155.3.1.1 | The compliance statement for entities that implement the CISCO-SDSL-LINE-MIB. Implementation of this MIB is mandatory for any platform that supports one or more SDSL line interfaces. This specification is replaced by ciscoSdslLineMIBStucComplianceRev1 | ||
| ciscoSdslLineMIBStucComplianceRev1 | 1.3.6.1.4.1.9.9.155.3.1.3 | The compliance statement for entities that implement the CISCO-SDSL-LINE-MIB. Implementation of this MIB is mandatory for any platform that supports one or more SDSL line interfaces. | ||
| ciscoSdslLineMIBSturCompliance | 1.3.6.1.4.1.9.9.155.3.1.2 | The compliance statement for entities that implement the CISCO-SDSL-LINE-MIB and manage SDSL STU-R class devices. Implementation of this MIB is mandatory for any platform that supports one or more SDSL line interfaces. This specification is replaced by ciscoSdslLineMIBSturComplianceRev1. | ||
| ciscoSdslLineMIBSturComplianceRev1 | 1.3.6.1.4.1.9.9.155.3.1.4 | The compliance statement for entities that implement the CISCO-SDSL-LINE-MIB and manage SDSL STU-R class devices. Implementation of this MIB is mandatory for any platform that supports one or more SDSL line interfaces. | ||
| ADS cSdslLineAlarmConfProfile | 1.3.6.1.4.1.9.9.155.1.1.1.5 | AdslLineProfileName | read-write | This object specifies the row in the adslLineAlarmConfProfileTable (see the ADSL-LINE-MIB for further details), which applies for this SDSL line interface. In the case the implementation utilizes 'dynamic mode' (see the ADSL-LINE-MIB for further details), then the value of this object defaults to the name of an alarm configuration profile designated by the implementation as the default alarm configuration profile. In the case the implementation utilizes 'static mode', then the the value of this object is read-only. |
| cSdslLineAlarmConfProfileEntry | 1.3.6.1.4.1.9.9.155.1.15.1 | not-accessible | A configuration profile containing enterprise-specific SDSL line configuration information pertaining to alarms | |
| cSdslLineAlarmConfProfileTable | 1.3.6.1.4.1.9.9.155.1.15 | not-accessible | This table extends the adslLineAlarmConfProfileTable and contains enterprise-specific SDSL line configuration information pertaining to alarms. | |
| T/F cSdslLineAutoRateEnable | 1.3.6.1.4.1.9.9.155.1.14.1.11 | TruthValue | read-create | This object specifies whether the device uses the rate adaptive training mode. |
| INT cSdslLineCoding | 1.3.6.1.4.1.9.9.155.1.1.1.1 | INTEGER | read-only | Specifies encoding of signal used by this line. Other types may be added in the future. |
| ADS cSdslLineConfProfile | 1.3.6.1.4.1.9.9.155.1.1.1.4 | AdslLineProfileName | read-write | This object specifies the row in the adslLineConfProfileTable (see the ADSL-LINE-MIB for further details), which applies for this SDSL line interface. In the case the implementation utilizes 'dynamic mode' (see the ADSL-LINE-MIB for further details), then the value of this object defaults to the name of a configuration profile designated by the implementation as the default configuration profile. In the case the implementation utilizes 'static mode', then the the value of this object is read-only. |
| cSdslLineConfProfileEntry | 1.3.6.1.4.1.9.9.155.1.14.1 | not-accessible | A configuration profile containing enterprise-specific SDSL line configuration information. | |
| cSdslLineConfProfileTable | 1.3.6.1.4.1.9.9.155.1.14 | not-accessible | This table extends the adslLineConfProfileTable and contains enterprise-specific SDSL line configuration information. | |
| cSdslLineEntry | 1.3.6.1.4.1.9.9.155.1.1.1 | not-accessible | A set of enterprise-specific common attributes describing both ends of an SDSL line supported by the system. There exists an entry for each ifEntry with an ifType of sdsl(96). | |
| INT cSdslLineEquipmentType | 1.3.6.1.4.1.9.9.155.1.14.1.10 | INTEGER | read-create | This object specifies the type of the STU device ,either STU-C or STU-R |
| INT cSdslLineFraming | 1.3.6.1.4.1.9.9.155.1.1.1.2 | INTEGER | read-only | This object specifies the current Transmission Convergence framing structure being used by the interface. |
| INT cSdslLineFramingMode | 1.3.6.1.4.1.9.9.155.1.14.1.2 | INTEGER | read-create | This object specifies the desired Transmission Convergence framing structure being used by the interface. |
| I32 cSdslLineMaxRate | 1.3.6.1.4.1.9.9.155.1.14.1.1 | Integer32 | read-create | This object specifies the desired line rate which the STU-C will attempt to train at. |
| NUM cSdslLineSpecific | 1.3.6.1.4.1.9.9.155.1.1.1.3 | VariablePointer | read-only | This object specifies an object identifier of an instance of an object in the MIB. The implementation determines the application of this object. For example, an implementation may use this object to provide a reference to the port-class physical entity (see the ENTITY-MIB for further details) corresponding to the SDSL line. |
| cSdslLineTable | 1.3.6.1.4.1.9.9.155.1.1 | not-accessible | This table contains the enterprise-specific common attributes describing both ends of SDSL lines supported by the system. | |
| INT cSdslShdslLineMaxRate | 1.3.6.1.4.1.9.9.155.1.14.1.7 | INTEGER | read-create | This object specifies the desired line rate at which the G.shdsl STU-C will attempt to train. |
| cSdslStucAlarmConfProfileGroup | 1.3.6.1.4.1.9.9.155.3.2.11 | A collection of traps generated by the agent to signal threshold alarms. | ||
| INT cSdslStucAnnex | 1.3.6.1.4.1.9.9.155.1.14.1.9 | INTEGER | read-create | This object specifies the operating conditions for the port of G.shdsl CO equipment . Annex A is optimized for conditions typically encountered within the North American network,whereas Annex B is optimized for conditions typically encountered within the European network. |
| cSdslStucBasicGroup | 1.3.6.1.4.1.9.9.155.3.2.1 | A collection of managed objects defining the basic operation of an STU-C (i.e., no rate adaptation). This specification is replaced by cSdslStucBasicGroupRev1. | ||
| cSdslStucBasicGroupRev1 | 1.3.6.1.4.1.9.9.155.3.2.12 | A collection of managed objects defining the basic operation of an STU-C. This specification is replaced by cSdslStucBasicGroupRev2. | ||
| cSdslStucBasicGroupRev2 | 1.3.6.1.4.1.9.9.155.3.2.14 | A collection of managed objects defining the basic operation of an STU-C. | ||
| G32 cSdslStucCurrAtn | 1.3.6.1.4.1.9.9.155.1.2.1.10 | Gauge32 | read-only | Measured difference in the total power transmitted by the peer STU-R and the total power received by this STU-C. |
| I32 cSdslStucCurrGain | 1.3.6.1.4.1.9.9.155.1.2.1.8 | Integer32 | read-only | This object specifies gain applied to this STU-C's receiver. This object is deprecated by cSdslStucCurrGainRev which has no specified range. |
| I32 cSdslStucCurrGainRev | 1.3.6.1.4.1.9.9.155.1.2.1.11 | Integer32 | read-only | This object specifies gain applied to this STU-C's receiver. This object deprecates cSdslStucCurrGainRev and has no specified range. |
| G32 cSdslStucCurrOutputPwr | 1.3.6.1.4.1.9.9.155.1.2.1.9 | Gauge32 | read-only | This object specifies the measured total output power transmitted by this STU-C. This is the measurement that was reported during the last activation sequence. |
| I32 cSdslStucCurrRate | 1.3.6.1.4.1.9.9.155.1.2.1.6 | Integer32 | read-only | This object specifies the rate the STU-C transceiver was able to obtain following training. |
| G32 cSdslStucCurrSnrMgn | 1.3.6.1.4.1.9.9.155.1.2.1.7 | Gauge32 | read-only | This object specifies the SNR margin as seen by this STU-C with respect to its received signal. |
| SDS cSdslStucDefect | 1.3.6.1.4.1.9.9.155.1.2.1.5 | SdslStuxDefect | read-only | This object specifies any possible defects currently being exhibited by the STU-C. This object has the intention of supplementing ifOperStatus. |
| NUM cSdslStucIntervalCVs | 1.3.6.1.4.1.9.9.155.1.8.1.5 | PerfIntervalCount | read-only | This object specifies the number of coding violations experienced by the STU-C in the interval. |
| cSdslStucIntervalEntry | 1.3.6.1.4.1.9.9.155.1.8.1 | not-accessible | A 15-miute interval of physical-layer statistics for a STU-C class device supported by the system. There exists up to 96 entries for each ifEntry with an ifType of sdsl(96). | |
| NUM cSdslStucIntervalESs | 1.3.6.1.4.1.9.9.155.1.8.1.6 | PerfIntervalCount | read-only | This object specifies the number of errored seconds experienced by the STU-C in the interval. |
| NUM cSdslStucIntervalInits | 1.3.6.1.4.1.9.9.155.1.8.1.9 | PerfIntervalCount | read-only | This object specifies the number of line initializations attempted by the STU-C in the interval. |
| NUM cSdslStucIntervalLOSQs | 1.3.6.1.4.1.9.9.155.1.8.1.4 | PerfIntervalCount | read-only | This object specifies the number of seconds in the interval when the STU-C experienced LOSQ. |
| NUM cSdslStucIntervalLOSs | 1.3.6.1.4.1.9.9.155.1.8.1.3 | PerfIntervalCount | read-only | This object specifies the number of seconds in the interval when the STU-C experienced LOS. |
| I32 cSdslStucIntervalNumber | 1.3.6.1.4.1.9.9.155.1.8.1.1 | Integer32 | not-accessible | The interval in which the statistics were collected, where the value of 1 represents the most recent interval, and the value of 96 represents the interval collected 24 hours ago. Intervals 2..96 are optional. |
| NUM cSdslStucIntervalSESs | 1.3.6.1.4.1.9.9.155.1.8.1.7 | PerfIntervalCount | read-only | This object specifies the number of severely errored seconds experienced by the STU-C in the interval. |
| cSdslStucIntervalTable | 1.3.6.1.4.1.9.9.155.1.8 | not-accessible | This table contains physical-layer statistics intervals for STU-C class devices supported by the system. The interval tables are modeled after RFC 2493, Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals, RFC 2493 | |
| NUM cSdslStucIntervalUASs | 1.3.6.1.4.1.9.9.155.1.8.1.8 | PerfIntervalCount | read-only | This object specifies the number of unavailable seconds experienced by the STU-C in the interval. |
| NUM cSdslStucIntervalUnavlRsrcs | 1.3.6.1.4.1.9.9.155.1.8.1.10 | PerfIntervalCount | read-only | This object specifies the number of packets discarded on the STU-C due to unavailable resources, such as lack of buffer space in the interval. |
| T/F cSdslStucIntervalValidData | 1.3.6.1.4.1.9.9.155.1.8.1.2 | TruthValue | read-only | This object specifies whether the data for this interval is valid. |
| STR cSdslStucInvSerialNumber | 1.3.6.1.4.1.9.9.155.1.2.1.1 | SnmpAdminString | read-only | This object specifies the vendor specific string that identifies the vendor STU-C. |
| STR cSdslStucInvVendorId | 1.3.6.1.4.1.9.9.155.1.2.1.2 | SnmpAdminString | read-only | This object specifies the vendor identifier assigned according to T1.220 |
| STR cSdslStucInvVersionNumber | 1.3.6.1.4.1.9.9.155.1.2.1.3 | SnmpAdminString | read-only | This object specifies the vendor specific version number of the STU-C. |
| I32 cSdslStucMaxSnrMgn | 1.3.6.1.4.1.9.9.155.1.14.1.4 | Integer32 | read-create | This object specifies the maximum acceptable SNR margin. If the noise margin exceeds this level, then the STU-C should attempt to reduce its power output to optimize its operation. The value for this object must be in multiples of 10. The specified value will be rounded down to the nearest valid tenth dB level if the value is not in multiples of 10. |
| I32 cSdslStucMinSnrMgn | 1.3.6.1.4.1.9.9.155.1.14.1.5 | Integer32 | read-create | This object specifies the minimum acceptable SNR margin. If the noise margin falls below this level, the STU-C will retrain. The value for this object must be in multiples of 10. The specified value will be rounded down to the nearest valid tenth dB level if the value is not in multiples of 10. |
| I32 cSdslStucOutputPwr | 1.3.6.1.4.1.9.9.155.1.14.1.6 | Integer32 | read-create | This object specifies the transmit power level used by the STU-C. The value for this object must be in multiples of 10. The specified value will be rounded down to the nearest valid tenth dB level if the value is not in multiples of 10. |
| PER cSdslStucPerfCurr15MinCVs | 1.3.6.1.4.1.9.9.155.1.6.1.14 | PerfCurrentCount | read-only | This object specifies the number of coding violations experienced by the STU-C in the current 15-minute interval. |
| PER cSdslStucPerfCurr15MinESs | 1.3.6.1.4.1.9.9.155.1.6.1.15 | PerfCurrentCount | read-only | This object specifies the number of errored seconds experienced by the STU-C in the current 15-minute interval. |
| PER cSdslStucPerfCurr15MinInits | 1.3.6.1.4.1.9.9.155.1.6.1.18 | PerfCurrentCount | read-only | This object specifies the number of line initializations attempted by the STU-C in the current 15-minute interval. |
| PER cSdslStucPerfCurr15MinLOSQs | 1.3.6.1.4.1.9.9.155.1.6.1.13 | PerfCurrentCount | read-only | This object specifies the number of seconds in the current 15-minute interval when the STU-C experienced LOSQ. |
| PER cSdslStucPerfCurr15MinLOSs | 1.3.6.1.4.1.9.9.155.1.6.1.12 | PerfCurrentCount | read-only | This object specifies the number of seconds in the current 15-minute interval when the STU-C experienced LOS. |
| PER cSdslStucPerfCurr15MinSESs | 1.3.6.1.4.1.9.9.155.1.6.1.16 | PerfCurrentCount | read-only | This object specifies the number of severely errored seconds experienced by the STU-C in the current 15-minute interval. |
| SDS cSdslStucPerfCurr15MinTimeElapse | 1.3.6.1.4.1.9.9.155.1.6.1.11 | SdslPerfTimeElapsed | read-only | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. |
| PER cSdslStucPerfCurr15MinUASs | 1.3.6.1.4.1.9.9.155.1.6.1.17 | PerfCurrentCount | read-only | This object specifies the number of unavailable seconds experienced by the STU-C in the current 15-minute interval. |
| PER cSdslStucPerfCurr15MinUnavlRsrcs | 1.3.6.1.4.1.9.9.155.1.6.1.19 | PerfCurrentCount | read-only | This object specifies the number of packets discarded on the STU-C due to unavailable resources, such as lack of buffer space, in the current 15 minute interval. |
| SDS cSdslStucPerfCurr1DayCVs | 1.3.6.1.4.1.9.9.155.1.6.1.23 | SdslPerfCurrDayCount | read-only | This object specifies the number of coding violations experienced by the STU-C in the current 1-day interval. |
| SDS cSdslStucPerfCurr1DayESs | 1.3.6.1.4.1.9.9.155.1.6.1.24 | SdslPerfCurrDayCount | read-only | This object specifies the number of errored seconds experienced by the STU-C in the current 1-day interval. |
| SDS cSdslStucPerfCurr1DayInits | 1.3.6.1.4.1.9.9.155.1.6.1.27 | SdslPerfCurrDayCount | read-only | This object specifies the number of line initializations attempted by the STU-C in the current 1-day interval. |
| SDS cSdslStucPerfCurr1DayLOSQs | 1.3.6.1.4.1.9.9.155.1.6.1.22 | SdslPerfCurrDayCount | read-only | This object specifies the number of seconds experienced by the STU-C in the current 1-day interval when there was LOSQ. |
| SDS cSdslStucPerfCurr1DayLOSs | 1.3.6.1.4.1.9.9.155.1.6.1.21 | SdslPerfCurrDayCount | read-only | This object specifies the number of seconds experienced by the STU-C in the current 1-day interval when there was LOS. |
| SDS cSdslStucPerfCurr1DaySESs | 1.3.6.1.4.1.9.9.155.1.6.1.25 | SdslPerfCurrDayCount | read-only | This object specifies the number of severely errored seconds experienced by the STU-C in the current 1-day interval. |
| SDS cSdslStucPerfCurr1DayTimeElapsed | 1.3.6.1.4.1.9.9.155.1.6.1.20 | SdslPerfTimeElapsed | read-only | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. |
| SDS cSdslStucPerfCurr1DayUASs | 1.3.6.1.4.1.9.9.155.1.6.1.26 | SdslPerfCurrDayCount | read-only | This object specifies the number of unavailable seconds experienced by the STU-C in the current 1-day interval. |
| SDS cSdslStucPerfCurr1DayUnavlRsrcs | 1.3.6.1.4.1.9.9.155.1.6.1.28 | SdslPerfCurrDayCount | read-only | This object specifies the number of packets discarded on the STU-C due to unavailable resources, such as lack of buffer space, in the current 1-day interval. |
| C32 cSdslStucPerfCVs | 1.3.6.1.4.1.9.9.155.1.6.1.3 | Counter32 | read-only | This object specifies the number of coding violations experienced by the STU-C since agent reset. |
| cSdslStucPerfDataEntry | 1.3.6.1.4.1.9.9.155.1.6.1 | not-accessible | A set of physical-layer statistics for an STU-C class device supported by the system. There exists an entry for each ifEntry with an ifType of sdsl(96). | |
| cSdslStucPerfDataTable | 1.3.6.1.4.1.9.9.155.1.6 | not-accessible | This table contains physical-layer statistics for STU-C class devices supported by the system. | |
| C32 cSdslStucPerfESs | 1.3.6.1.4.1.9.9.155.1.6.1.4 | Counter32 | read-only | This object specifies the number of errored seconds experienced by the STU-C since agent reset. |
| C32 cSdslStucPerfInits | 1.3.6.1.4.1.9.9.155.1.6.1.7 | Counter32 | read-only | This object specifies the number of line initializations attempted by the STU-C since agent reset. This value includes both successful and failed attempts. |
| I32 cSdslStucPerfInvalidIntervals | 1.3.6.1.4.1.9.9.155.1.6.1.10 | Integer32 | read-only | The number of near-end performance data 15-minute intervals in the range from 0 to cSdslStucPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations). |
| C32 cSdslStucPerfLOSQs | 1.3.6.1.4.1.9.9.155.1.6.1.2 | Counter32 | read-only | This object specifies the number of LOSQ failures experienced by the STU-C since agent reset. |
| C32 cSdslStucPerfLOSsEx | 1.3.6.1.4.1.9.9.155.1.6.1.1 | Counter32 | read-only | This object specifies the number of LOS failures experienced by the STU-C since agent reset. |
| SDS cSdslStucPerfPrev1DayCVs | 1.3.6.1.4.1.9.9.155.1.6.1.32 | SdslPerfPrevDayCount | read-only | This object specifies the number of coding violations experienced by the STU-C in the previous 1-day interval. |
| SDS cSdslStucPerfPrev1DayESs | 1.3.6.1.4.1.9.9.155.1.6.1.33 | SdslPerfPrevDayCount | read-only | This object specifies the number of errored seconds experienced by the STU-C in the previous 1-day interval. |
| SDS cSdslStucPerfPrev1DayInits | 1.3.6.1.4.1.9.9.155.1.6.1.36 | SdslPerfPrevDayCount | read-only | This object specifies the number of line initializations attempted by the STU-C in the previous 1-day interval. |
| SDS cSdslStucPerfPrev1DayLOSQs | 1.3.6.1.4.1.9.9.155.1.6.1.31 | SdslPerfPrevDayCount | read-only | This object specifies the number of seconds in the previous 1-day interval when the STU-C experienced LOSQ. |
| SDS cSdslStucPerfPrev1DayLOSs | 1.3.6.1.4.1.9.9.155.1.6.1.30 | SdslPerfPrevDayCount | read-only | This object specifies the number of seconds in the current 1-day interval when the STU-C experienced LOS. |
| I32 cSdslStucPerfPrev1DayMoniSecs | 1.3.6.1.4.1.9.9.155.1.6.1.29 | Integer32 | read-only | The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason. |
| SDS cSdslStucPerfPrev1DaySESs | 1.3.6.1.4.1.9.9.155.1.6.1.34 | SdslPerfPrevDayCount | read-only | This object specifies the number of severely errored seconds experienced by the STU-C in the previous 1-day interval. |
| SDS cSdslStucPerfPrev1DayUASs | 1.3.6.1.4.1.9.9.155.1.6.1.35 | SdslPerfPrevDayCount | read-only | This object specifies the number of unavailable seconds experienced by the STU-C in the previous 1-day interval. |
| SDS cSdslStucPerfPrev1DayUnavlRsrcs | 1.3.6.1.4.1.9.9.155.1.6.1.37 | SdslPerfPrevDayCount | read-only | This object specifies the number of packets discarded on the STU-C due to unavailable resources, such as lack of buffer space, in the previous 1-day interval. |
| C32 cSdslStucPerfSESs | 1.3.6.1.4.1.9.9.155.1.6.1.5 | Counter32 | read-only | This object specifies the number of severely errored seconds experienced by the STU-C since agent reset. |
| C32 cSdslStucPerfUASs | 1.3.6.1.4.1.9.9.155.1.6.1.6 | Counter32 | read-only | This object specifies the number of unavailable seconds experienced by the STU-C since agent reset. |
| I32 cSdslStucPerfValidIntervals | 1.3.6.1.4.1.9.9.155.1.6.1.9 | Integer32 | read-only | The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute near end intervals since the interface has been online. |
| cSdslStucPhysEntry | 1.3.6.1.4.1.9.9.155.1.2.1 | not-accessible | A set of enterprise-specific physical-layer parameters for an STU-C class device supported by the system. There exists an entry for each ifEntry with an ifType of sdsl(96). | |
| cSdslStucPhysTable | 1.3.6.1.4.1.9.9.155.1.2 | not-accessible | This table contains enterprise-specific physical layer parameters for STU-C class devices supported by the system. | |
| cSdslStucPM15MinIntervalGroup | 1.3.6.1.4.1.9.9.155.3.2.5 | A collection of managed objects defining near-end performance data collection capability using 15-minute intervals. | ||
| cSdslStucPM1DayIntervalGroup | 1.3.6.1.4.1.9.9.155.3.2.6 | A collection of managed objects defining near-end performance data collection capability using 1-day intervals. | ||
| cSdslStucPMCounterGroup | 1.3.6.1.4.1.9.9.155.3.2.4 | A collection of managed objects defining basic near-end performance monitoring capability. | ||
| INT cSdslStucPsdMaskType | 1.3.6.1.4.1.9.9.155.1.14.1.8 | INTEGER | read-create | This object specifies the PSD mask type for the transceiver. For all values of the cSdslShdslLineMaxRate, the symmetric PSD masktype is selectable. Asymmetric mask is only selectable for the following rates: 776000, 784000, 1552000, 2056000, 2312000. |
| cSdslStucRateAdaptiveGroup | 1.3.6.1.4.1.9.9.155.3.2.10 | A collection of managed objects defining rate adaptive operation of an STU-C. | ||
| INT cSdslStucState | 1.3.6.1.4.1.9.9.155.1.2.1.4 | INTEGER | read-only | This object specifies the state of the STU-C transceiver. |
| I32 cSdslStucTargetSnrMgn | 1.3.6.1.4.1.9.9.155.1.14.1.3 | Integer32 | read-create | This object specifies the target SNR margin. This is the desired noise margin the STU-C must achieve with a BER of 10-7 or better to successfully complete training. The value for this object must be in multiples of 10. The specified value will be rounded down to the nearest valid tenth dB level if the value is not in multiples of 10. |
| I32 cSdslStucThreshMinRate | 1.3.6.1.4.1.9.9.155.1.15.1.1 | Integer32 | read-create | This object specifies the line rate threshold. When the agent observes the line rate fall below this value, an appropriate alarm should be generated. The default value for this object should be the value of the cSdslLineMaxRate object. If the agent implements the CISCO-ENTITY-ALARM-MIB, the alarm generated should be through the mechanism defined by the CISCO-ENTITY-ALARM-MIB. Furthermore, the default severity of this alarm should be 'minor'. |
| I32 cSdslStucThreshMinSnrMgn | 1.3.6.1.4.1.9.9.155.1.15.1.2 | Integer32 | read-create | This object specifies the SNR margin threshold. When the agent observes the received SNR margin fall below this value, an appropriate alarm should be generated. If the agent implements the CISCO-ENTITY-ALARM-MIB, the alarm generated should be through the mechanism defined by the CISCO-ENTITY-ALARM-MIB. Furthermore, the default severity of this alarm should be 'minor'. |
| I32 cSdslStucThresholdSnrMgn | 1.3.6.1.4.1.9.9.155.1.14.1.12 | Integer32 | read-create | This object specifies the SNR margin threshold. An appropriate alarm should be generated when the difference between the actual SNR and the SNR required to maintain BER of 10E-7 is less than this value. The value for this object must be in multiples of 10. The specified value will be rounded down to the nearest valid tenth dB level if the value is not in multiples of 10. If the agent implements the CISCO-ENTITY-ALARM-MIB, the alarm generated should be through the mechanism defined by the CISCO-ENTITY-ALARM-MIB. Furthermore, the default severity of this alarm should be 'minor'. |
| C32 cSdslStucUnavailRsrcs | 1.3.6.1.4.1.9.9.155.1.6.1.8 | Counter32 | read-only | This object specifies the number of packets discarded on the STU-C due to unavailable resources, such as lack of buffer space. |
| INT cSdslSturAnnex | 1.3.6.1.4.1.9.9.155.1.14.1.13 | INTEGER | read-create | This object specifies the operating conditions for the port of G.shdsl CPE equipment. Annex A is optimized for conditions typically encountered within the North American network,whereas Annex B is optimized for conditions typically encountered within the European network. |
| cSdslSturBasicGroup | 1.3.6.1.4.1.9.9.155.3.2.2 | A collection of managed objects defining the basic operation of an STU-R.This specification is replaced by cSdslSturBasicGroupRev1 | ||
| cSdslSturBasicGroupRev1 | 1.3.6.1.4.1.9.9.155.3.2.13 | A collection of managed objects defining the basic operation of an STU-R. This specification is replaced by cSdslSturBasicGroupRev2 | ||
| cSdslSturBasicGroupRev2 | 1.3.6.1.4.1.9.9.155.3.2.15 | A collection of managed objects defining the basic operation of an STU-R. | ||
| G32 cSdslSturCurrAtn | 1.3.6.1.4.1.9.9.155.1.3.1.10 | Gauge32 | read-only | Measured difference in the total power transmitted by the peer STU-C and the total power received by this STU-R |
| I32 cSdslSturCurrGain | 1.3.6.1.4.1.9.9.155.1.3.1.8 | Integer32 | read-only | This object specifies gain applied to this STU-R's receiver. This object is deprecated by cSdslSturCurrGainRev which has no specified range. |
| I32 cSdslSturCurrGainRev | 1.3.6.1.4.1.9.9.155.1.3.1.11 | Integer32 | read-only | This object specifies gain applied to this STU-R's receiver. This object deprecates by cSdslSturCurrGain and has no specified range. |
| G32 cSdslSturCurrOutputPwr | 1.3.6.1.4.1.9.9.155.1.3.1.9 | Gauge32 | read-only | This object specifies the measured total output power transmitted by this STU-R. This is the measurement that was reported during the last activation sequence. |
| I32 cSdslSturCurrRate | 1.3.6.1.4.1.9.9.155.1.3.1.6 | Integer32 | read-only | This object specifies the rate the STU-R transceiver was able to obtain following training. |
| G32 cSdslSturCurrSnrMgn | 1.3.6.1.4.1.9.9.155.1.3.1.7 | Gauge32 | read-only | This object specifies the SNR margin as seen by this STU-R with respect to its received signal. |
| SDS cSdslSturDefect | 1.3.6.1.4.1.9.9.155.1.3.1.5 | SdslStuxDefect | read-only | This object specifies any possible defects currently being exhibited by the STU-R. This object has the intention of supplementing ifOperStatus. |
| cSdslSturGroup | 1.3.6.1.4.1.9.9.155.3.2.3 | A collection of managed objects defining the capability to remotely manage a STU-R. This is replaced by cSdslSturGroupRev1. | ||
| cSdslSturGroupRev1 | 1.3.6.1.4.1.9.9.155.3.2.16 | A collection of managed objects defining the capability to remotely manage a STU-R. | ||
| NUM cSdslSturIntervalCVs | 1.3.6.1.4.1.9.9.155.1.9.1.5 | PerfIntervalCount | read-only | This object specifies the number of coding violations experienced by the STU-R in the interval. |
| cSdslSturIntervalEntry | 1.3.6.1.4.1.9.9.155.1.9.1 | not-accessible | A 15-miute interval of physical-layer statistics for a STU-R class device supported by the system. There exists up to 96 entries for each ifEntry with an ifType of sdsl(96). | |
| NUM cSdslSturIntervalESs | 1.3.6.1.4.1.9.9.155.1.9.1.6 | PerfIntervalCount | read-only | This object specifies the number of errored seconds experienced by the STU-R in the interval. |
| NUM cSdslSturIntervalLOSQs | 1.3.6.1.4.1.9.9.155.1.9.1.4 | PerfIntervalCount | read-only | This object specifies the number of seconds in the interval when the STU-R experienced LOSQ. |
| NUM cSdslSturIntervalLOSs | 1.3.6.1.4.1.9.9.155.1.9.1.3 | PerfIntervalCount | read-only | This object specifies the number of seconds in the interval when the STU-R experienced LOS. |
| I32 cSdslSturIntervalNumber | 1.3.6.1.4.1.9.9.155.1.9.1.1 | Integer32 | not-accessible | The interval in which the statistics were collected, where the value of 1 represents the most recent interval, and the value of 96 represents the interval collected 24 hours ago. Intervals 2..96 are optional. |
| NUM cSdslSturIntervalSESs | 1.3.6.1.4.1.9.9.155.1.9.1.7 | PerfIntervalCount | read-only | This object specifies the number of severely errored seconds experienced by the STU-R in the interval. |
| cSdslSturIntervalTable | 1.3.6.1.4.1.9.9.155.1.9 | not-accessible | This table contains physical-layer statistics intervals for STU-R class devices supported by the system. The interval tables are modeled after RFC 2493, Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals, RFC 2493 | |
| NUM cSdslSturIntervalUASs | 1.3.6.1.4.1.9.9.155.1.9.1.8 | PerfIntervalCount | read-only | This object specifies the number of unavailable seconds experienced by the STU-R in the interval. |
| T/F cSdslSturIntervalValidData | 1.3.6.1.4.1.9.9.155.1.9.1.2 | TruthValue | read-only | This object specifies whether the data for this interval is valid. |
| STR cSdslSturInvSerialNumber | 1.3.6.1.4.1.9.9.155.1.3.1.1 | SnmpAdminString | read-only | This object specifies the vendor specific string that identifies the vendor STU-R. |
| STR cSdslSturInvVendorId | 1.3.6.1.4.1.9.9.155.1.3.1.2 | SnmpAdminString | read-only | This object specifies the vendor identifier assigned according to T1.220 |
| STR cSdslSturInvVersionNumber | 1.3.6.1.4.1.9.9.155.1.3.1.3 | SnmpAdminString | read-only | This object specifies the vendor specific version number of the STU-R. |
| PER cSdslSturPerfCurr15MinCVs | 1.3.6.1.4.1.9.9.155.1.7.1.12 | PerfCurrentCount | read-only | This object specifies the number of coding violations experienced by the STU-R in the current 15-minute interval. |
| PER cSdslSturPerfCurr15MinESs | 1.3.6.1.4.1.9.9.155.1.7.1.13 | PerfCurrentCount | read-only | This object specifies the number of errored seconds experienced by the STU-R in the current 15-minute interval. |
| PER cSdslSturPerfCurr15MinLOSQs | 1.3.6.1.4.1.9.9.155.1.7.1.11 | PerfCurrentCount | read-only | This object specifies the number of seconds in the current 15-minute interval when the STU-R experienced LOSQ. |
| PER cSdslSturPerfCurr15MinLOSs | 1.3.6.1.4.1.9.9.155.1.7.1.10 | PerfCurrentCount | read-only | This object specifies the number of seconds in the current 15-minute interval when the STU-R experienced LOS. |
| PER cSdslSturPerfCurr15MinSESs | 1.3.6.1.4.1.9.9.155.1.7.1.14 | PerfCurrentCount | read-only | This object specifies the number of severely errored seconds experienced by the STU-R in the current 15-minute interval. |
| SDS cSdslSturPerfCurr15MinTimeElapse | 1.3.6.1.4.1.9.9.155.1.7.1.9 | SdslPerfTimeElapsed | read-only | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. |
| PER cSdslSturPerfCurr15MinUASs | 1.3.6.1.4.1.9.9.155.1.7.1.15 | PerfCurrentCount | read-only | This object specifies the number of unavailable seconds experienced by the STU-R in the current 15-minute interval. |
| SDS cSdslSturPerfCurr1DayCVs | 1.3.6.1.4.1.9.9.155.1.7.1.19 | SdslPerfCurrDayCount | read-only | This object specifies the number of coding violations experienced by the STU-R in the current 1-day interval. |
| SDS cSdslSturPerfCurr1DayESs | 1.3.6.1.4.1.9.9.155.1.7.1.20 | SdslPerfCurrDayCount | read-only | This object specifies the number of errored seconds experienced by the STU-R in the current 1-day interval. |
| SDS cSdslSturPerfCurr1DayLOSQs | 1.3.6.1.4.1.9.9.155.1.7.1.18 | SdslPerfCurrDayCount | read-only | This object specifies the number of seconds experienced by the STU-R in the current 1-day interval when there was LOSQ. |
| SDS cSdslSturPerfCurr1DayLOSs | 1.3.6.1.4.1.9.9.155.1.7.1.17 | SdslPerfCurrDayCount | read-only | This object specifies the number of seconds experienced by the STU-R in the current 1-day interval when there was LOS. |
| SDS cSdslSturPerfCurr1DaySESs | 1.3.6.1.4.1.9.9.155.1.7.1.21 | SdslPerfCurrDayCount | read-only | This object specifies the number of severely errored seconds experienced by the STU-R in the current 1-day interval. |
| SDS cSdslSturPerfCurr1DayTimeElapsed | 1.3.6.1.4.1.9.9.155.1.7.1.16 | SdslPerfTimeElapsed | read-only | The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. |
| SDS cSdslSturPerfCurr1DayUASs | 1.3.6.1.4.1.9.9.155.1.7.1.22 | SdslPerfCurrDayCount | read-only | This object specifies the number of unavailable seconds experienced by the STU-R in the current 1-day interval. |
| C32 cSdslSturPerfCVs | 1.3.6.1.4.1.9.9.155.1.7.1.3 | Counter32 | read-only | This object specifies the number of coding violations experienced by the STU-R since agent reset. |
| cSdslSturPerfDataEntry | 1.3.6.1.4.1.9.9.155.1.7.1 | not-accessible | A set of physical-layer statistics for an STU-R class device supported by the system. There exists an entry for each ifEntry with an ifType of sdsl(96). | |
| cSdslSturPerfDataTable | 1.3.6.1.4.1.9.9.155.1.7 | not-accessible | This table contains physical-layer statistics for STU-R class devices supported by the system. -- Note to implementor: -- If the implementation does not support remote management -- of STU-R class devices, then the agent must respond with -- the appropriate error indicating that the instance does not -- exist; that is, 'noSuchName' in response to a SNMPv1 get -- request, and 'noSuchInstance' in response to a SNMPv2 get -- request. | |
| C32 cSdslSturPerfESs | 1.3.6.1.4.1.9.9.155.1.7.1.4 | Counter32 | read-only | This object specifies the number of errored seconds experienced by the STU-R since agent reset. |
| I32 cSdslSturPerfInvalidIntervals | 1.3.6.1.4.1.9.9.155.1.7.1.8 | Integer32 | read-only | The number of far-end performance data 15-minute intervals in the range from 0 to cSdslSturPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations). |
| C32 cSdslSturPerfLOSQs | 1.3.6.1.4.1.9.9.155.1.7.1.2 | Counter32 | read-only | This object specifies the number of LOSQ failures experienced by the STU-R since agent reset. |
| C32 cSdslSturPerfLOSs | 1.3.6.1.4.1.9.9.155.1.7.1.1 | Counter32 | read-only | This object specifies the number of LOS failures experienced by the STU-R since agent reset. |
| SDS cSdslSturPerfPrev1DayCVs | 1.3.6.1.4.1.9.9.155.1.7.1.26 | SdslPerfPrevDayCount | read-only | This object specifies the number of coding violations experienced by the STU-R in the previous 1-day interval. |
| SDS cSdslSturPerfPrev1DayESs | 1.3.6.1.4.1.9.9.155.1.7.1.27 | SdslPerfPrevDayCount | read-only | This object specifies the number of errored seconds experienced by the STU-R in the previous 1-day interval. |
| SDS cSdslSturPerfPrev1DayLOSQs | 1.3.6.1.4.1.9.9.155.1.7.1.25 | SdslPerfPrevDayCount | read-only | This object specifies the number of seconds in the previous 1-day interval when the STU-R experienced LOSQ. |
| SDS cSdslSturPerfPrev1DayLOSs | 1.3.6.1.4.1.9.9.155.1.7.1.24 | SdslPerfPrevDayCount | read-only | This object specifies the number of seconds in the current 1-day interval when the STU-R experienced LOS. |
| I32 cSdslSturPerfPrev1DayMoniSecs | 1.3.6.1.4.1.9.9.155.1.7.1.23 | Integer32 | read-only | The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason. |
| SDS cSdslSturPerfPrev1DaySESs | 1.3.6.1.4.1.9.9.155.1.7.1.28 | SdslPerfPrevDayCount | read-only | This object specifies the number of severely errored seconds experienced by the STU-R in the previous 1-day interval. |
| SDS cSdslSturPerfPrev1DayUASs | 1.3.6.1.4.1.9.9.155.1.7.1.29 | SdslPerfPrevDayCount | read-only | This object specifies the number of unavailable seconds experienced by the STU-R in the previous 1-day interval. |
| C32 cSdslSturPerfSESs | 1.3.6.1.4.1.9.9.155.1.7.1.5 | Counter32 | read-only | This object specifies the number of severely errored seconds experienced by the STU-R since agent reset. |
| C32 cSdslSturPerfUASs | 1.3.6.1.4.1.9.9.155.1.7.1.6 | Counter32 | read-only | This object specifies the number of unavailable seconds experienced by the STU-R since agent reset. |
| I32 cSdslSturPerfValidIntervals | 1.3.6.1.4.1.9.9.155.1.7.1.7 | Integer32 | read-only | The number of previous far end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute far end intervals since the interface has been online. |
| cSdslSturPhysEntry | 1.3.6.1.4.1.9.9.155.1.3.1 | not-accessible | A set of enterprise-specific physical-layer parameters for an STU-R class device supported by the system. There exists an entry for each ifEntry with an ifType of sdsl(96). | |
| cSdslSturPhysTable | 1.3.6.1.4.1.9.9.155.1.3 | not-accessible | This table contains enterprise-specific physical layer parameters for STU-R class devices supported by the system. -- Note to implementor: -- If the implementation does not support remote management -- of STU-R class devices, then the agent must respond with -- the appropriate error indicating that the instance does not -- exist; that is, 'noSuchName' in response to a SNMPv1 get -- request, 'noSuchInstance' in response to a SNMPv2 get -- request or a null string for string types. | |
| cSdslSturPM15MinIntervalGroup | 1.3.6.1.4.1.9.9.155.3.2.8 | A collection of managed objects defining far-end performance data collection capability using 15-minute intervals. | ||
| cSdslSturPM1DayIntervalGroup | 1.3.6.1.4.1.9.9.155.3.2.9 | A collection of managed objects defining far-end performance data collection capability using 1-day intervals. | ||
| cSdslSturPMCounterGroup | 1.3.6.1.4.1.9.9.155.3.2.7 | A collection of managed objects defining basic far-end performance monitoring capability. | ||
| INT cSdslSturState | 1.3.6.1.4.1.9.9.155.1.3.1.4 | INTEGER | read-only | This object specifies the state of the STU-R transceiver. |
RFC description
Management of symmetric DSL (SDSL) line interfaces, including configuration profiles, performance counters, and line statistics for DSL modems.
Start monitoring Cisco SDSL DSLAMs and routers with SDSL line cards with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.